Merge branch 'highbank/soc' into next/soc

Conflicts:
	arch/arm/mach-mxs/include/mach/gpio.h
	arch/arm/mach-omap2/board-generic.c
	arch/arm/plat-mxc/include/mach/gpio.h

303 files changed, 2996 insertions, 2057 deletions

diff --git a/Documentation/devicetree/bindings/arm/calxeda.txt b/Documentation/devicetree/bindings/arm/calxeda.txt
new file mode 100644
index 000000000000..4755caaccba6
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/calxeda.txt
@@ -0,0 +1,8 @@
+Calxeda Highbank Platforms Device Tree Bindings
+-----------------------------------------------
+
+Boards with Calxeda Cortex-A9 based Highbank SOC shall have the following
+properties.
+
+Required root node properties:
+    - compatible = "calxeda,highbank";
diff --git a/Documentation/devicetree/bindings/arm/l2cc.txt b/Documentation/devicetree/bindings/arm/l2cc.txt
new file mode 100644
index 000000000000..7ca52161e7ab
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/l2cc.txt
@@ -0,0 +1,44 @@
+* ARM L2 Cache Controller
+
+ARM cores often have a separate level 2 cache controller. There are various
+implementations of the L2 cache controller with compatible programming models.
+The ARM L2 cache representation in the device tree should be done as follows:
+
+Required properties:
+
+- compatible : should be one of:
+	"arm,pl310-cache"
+	"arm,l220-cache"
+	"arm,l210-cache"
+- cache-unified : Specifies the cache is a unified cache.
+- cache-level : Should be set to 2 for a level 2 cache.
+- reg : Physical base address and size of cache controller's memory mapped
+  registers.
+
+Optional properties:
+
+- arm,data-latency : Cycles of latency for Data RAM accesses. Specifies 3 cells of
+  read, write and setup latencies. Minimum valid values are 1. Controllers
+  without setup latency control should use a value of 0.
+- arm,tag-latency : Cycles of latency for Tag RAM accesses. Specifies 3 cells of
+  read, write and setup latencies. Controllers without setup latency control
+  should use 0. Controllers without separate read and write Tag RAM latency
+  values should only use the first cell.
+- arm,dirty-latency : Cycles of latency for Dirty RAMs. This is a single cell.
+- arm,filter-ranges : <start length> Starting address and length of window to
+  filter. Addresses in the filter window are directed to the M1 port. Other
+  addresses will go to the M0 port.
+- interrupts : 1 combined interrupt.
+
+Example:
+
+L2: cache-controller {
+        compatible = "arm,pl310-cache";
+        reg = <0xfff12000 0x1000>;
+        arm,data-latency = <1 1 1>;
+        arm,tag-latency = <2 2 2>;
+        arm,filter-latency = <0x80000000 0x8000000>;
+        cache-unified;
+        cache-level = <2>;
+	interrupts = <45>;
+};
diff --git a/MAINTAINERS b/MAINTAINERS
index 6185d0513584..5066335b97de 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -688,6 +688,12 @@ F:	drivers/mtd/nand/bcm_umi_nand.c
 F:	drivers/mtd/nand/bcm_umi_bch.c
 F:	drivers/mtd/nand/nand_bcm_umi.h
 
+ARM/CALXEDA HIGHBANK ARCHITECTURE
+M:	Rob Herring <rob.herring@calxeda.com>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+S:	Maintained
+F:	arch/arm/mach-highbank/
+
 ARM/CAVIUM NETWORKS CNS3XXX MACHINE SUPPORT
 M:	Anton Vorontsov <avorontsov@mvista.com>
 S:	Maintained
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index a94a09ba356b..6147d30a832c 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -330,6 +330,20 @@ config ARCH_BCMRING
 	help
 	  Support for Broadcom's BCMRing platform.
 
+config ARCH_HIGHBANK
+	bool "Calxeda Highbank-based"
+	select ARCH_WANT_OPTIONAL_GPIOLIB
+	select ARM_AMBA
+	select ARM_GIC
+	select ARM_TIMER_SP804
+	select CLKDEV_LOOKUP
+	select CPU_V7
+	select GENERIC_CLOCKEVENTS
+	select HAVE_ARM_SCU
+	select USE_OF
+	help
+	  Support for the Calxeda Highbank SoC based boards.
+
 config ARCH_CLPS711X
 	bool "Cirrus Logic CLPS711x/EP721x-based"
 	select CPU_ARM720T
@@ -862,6 +876,7 @@ config ARCH_U300
 	select CLKDEV_LOOKUP
 	select HAVE_MACH_CLKDEV
 	select GENERIC_GPIO
+	select ARCH_REQUIRE_GPIOLIB
 	select NEED_MACH_MEMORY_H
 	help
 	  Support for ST-Ericsson U300 series mobile platforms.
@@ -1402,7 +1417,7 @@ config SMP
 	depends on REALVIEW_EB_ARM11MP || REALVIEW_EB_A9MP || \
 		 MACH_REALVIEW_PB11MP || MACH_REALVIEW_PBX || ARCH_OMAP4 || \
 		 ARCH_EXYNOS4 || ARCH_TEGRA || ARCH_U8500 || ARCH_VEXPRESS_CA9X4 || \
-		 ARCH_MSM_SCORPIONMP || ARCH_SHMOBILE
+		 ARCH_MSM_SCORPIONMP || ARCH_SHMOBILE || ARCH_HIGHBANK
 	select USE_GENERIC_SMP_HELPERS
 	select HAVE_ARM_SCU if !ARCH_MSM_SCORPIONMP
 	help
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index be3a0f78d915..4bb7eb90f070 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -65,13 +65,78 @@ config DEBUG_USER
 
 # These options are only for real kernel hackers who want to get their hands dirty.
 config DEBUG_LL
-	bool "Kernel low-level debugging functions"
+	bool "Kernel low-level debugging functions (read help!)"
 	depends on DEBUG_KERNEL
 	help
 	  Say Y here to include definitions of printascii, printch, printhex
 	  in the kernel.  This is helpful if you are debugging code that
 	  executes before the console is initialized.
 
+	  Note that selecting this option will limit the kernel to a single
+	  UART definition, as specified below. Attempting to boot the kernel
+	  image on a different platform *will not work*, so this option should
+	  not be enabled for kernels that are intended to be portable.
+
+choice
+	prompt "Kernel low-level debugging port"
+	depends on DEBUG_LL
+
+	config DEBUG_LL_UART_NONE
+		bool "No low-level debugging UART"
+		help
+		  Say Y here if your platform doesn't provide a UART option
+		  below. This relies on your platform choosing the right UART
+		  definition internally in order for low-level debugging to
+		  work.
+
+	config DEBUG_ICEDCC
+		bool "Kernel low-level debugging via EmbeddedICE DCC channel"
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the EmbeddedICE macrocell's DCC channel using
+		  co-processor 14. This is known to work on the ARM9 style ICE
+		  channel and on the XScale with the PEEDI.
+
+		  Note that the system will appear to hang during boot if there
+		  is nothing connected to read from the DCC.
+
+	config DEBUG_FOOTBRIDGE_COM1
+		bool "Kernel low-level debugging messages via footbridge 8250 at PCI COM1"
+		depends on FOOTBRIDGE
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the 8250 at PCI COM1.
+
+	config DEBUG_DC21285_PORT
+		bool "Kernel low-level debugging messages via footbridge serial port"
+		depends on FOOTBRIDGE
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the serial port in the DC21285 (Footbridge).
+
+	config DEBUG_CLPS711X_UART1
+		bool "Kernel low-level debugging messages via UART1"
+		depends on ARCH_CLPS711X
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the first serial port on these devices.
+
+	config DEBUG_CLPS711X_UART2
+		bool "Kernel low-level debugging messages via UART2"
+		depends on ARCH_CLPS711X
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the second serial port on these devices.
+
+	config DEBUG_HIGHBANK_UART
+		bool "Kernel low-level debugging messages via Highbank UART"
+		depends on ARCH_HIGHBANK
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the UART on Highbank based devices.
+
+endchoice
+
 config EARLY_PRINTK
 	bool "Early printk"
 	depends on DEBUG_LL
@@ -80,18 +145,6 @@ config EARLY_PRINTK
 	  kernel low-level debugging functions. Add earlyprintk to your
 	  kernel parameters to enable this console.
 
-config DEBUG_ICEDCC
-	bool "Kernel low-level debugging via EmbeddedICE DCC channel"
-	depends on DEBUG_LL
-	help
-	  Say Y here if you want the debug print routines to direct their
-	  output to the EmbeddedICE macrocell's DCC channel using
-	  co-processor 14. This is known to work on the ARM9 style ICE
-	  channel and on the XScale with the PEEDI.
-
-	  It does include a timeout to ensure that the system does not
-	  totally freeze when there is nothing connected to read.
-
 config OC_ETM
 	bool "On-chip ETM and ETB"
 	select ARM_AMBA
@@ -100,23 +153,6 @@ config OC_ETM
 	  buffer driver that will allow you to collect traces of the
 	  kernel code.
 
-config DEBUG_DC21285_PORT
-	bool "Kernel low-level debugging messages via footbridge serial port"
-	depends on DEBUG_LL && FOOTBRIDGE
-	help
-	  Say Y here if you want the debug print routines to direct their
-	  output to the serial port in the DC21285 (Footbridge). Saying N
-	  will cause the debug messages to appear on the first 16550
-	  serial port.
-
-config DEBUG_CLPS711X_UART2
-	bool "Kernel low-level debugging messages via UART2"
-	depends on DEBUG_LL && ARCH_CLPS711X
-	help
-	  Say Y here if you want the debug print routines to direct their
-	  output to the second serial port on these devices.  Saying N will
-	  cause the debug messages to appear on the first serial port.
-
 config DEBUG_S3C_UART
 	depends on PLAT_SAMSUNG
 	int "S3C UART to use for low-level debug"
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index 8904caa736cb..e8688114ca95 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -144,6 +144,7 @@ machine-$(CONFIG_ARCH_EBSA110)		:= ebsa110
 machine-$(CONFIG_ARCH_EP93XX)		:= ep93xx
 machine-$(CONFIG_ARCH_GEMINI)		:= gemini
 machine-$(CONFIG_ARCH_H720X)		:= h720x
+machine-$(CONFIG_ARCH_HIGHBANK)		:= highbank
 machine-$(CONFIG_ARCH_INTEGRATOR)	:= integrator
 machine-$(CONFIG_ARCH_IOP13XX)		:= iop13xx
 machine-$(CONFIG_ARCH_IOP32X)		:= iop32x
diff --git a/arch/arm/boot/dts/highbank.dts b/arch/arm/boot/dts/highbank.dts
new file mode 100644
index 000000000000..aeb1a7578fad
--- /dev/null
+++ b/arch/arm/boot/dts/highbank.dts
@@ -0,0 +1,198 @@
+/*
+ * Copyright 2011 Calxeda, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/dts-v1/;
+
+/* First 4KB has pen for secondary cores. */
+/memreserve/ 0x00000000 0x0001000;
+
+/ {
+	model = "Calxeda Highbank";
+	compatible = "calxeda,highbank";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "arm,cortex-a9";
+			reg = <0>;
+			next-level-cache = <&L2>;
+		};
+
+		cpu@1 {
+			compatible = "arm,cortex-a9";
+			reg = <1>;
+			next-level-cache = <&L2>;
+		};
+
+		cpu@2 {
+			compatible = "arm,cortex-a9";
+			reg = <2>;
+			next-level-cache = <&L2>;
+		};
+
+		cpu@3 {
+			compatible = "arm,cortex-a9";
+			reg = <3>;
+			next-level-cache = <&L2>;
+		};
+	};
+
+	memory {
+		name = "memory";
+		device_type = "memory";
+		reg = <0x00000000 0xff900000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyAMA0";
+	};
+
+	soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		interrupt-parent = <&intc>;
+		ranges;
+
+		timer@fff10600 {
+			compatible = "arm,smp-twd";
+			reg = <0xfff10600 0x20>;
+			interrupts = <1 13 0xf04>;
+		};
+
+		watchdog@fff10620 {
+			compatible = "arm,cortex-a9-wdt";
+			reg = <0xfff10620 0x20>;
+			interrupts = <1 14 0xf04>;
+		};
+
+		intc: interrupt-controller@fff11000 {
+			compatible = "arm,cortex-a9-gic";
+			#interrupt-cells = <3>;
+			#size-cells = <0>;
+			#address-cells = <1>;
+			interrupt-controller;
+			interrupt-parent;
+			reg = <0xfff11000 0x1000>,
+			      <0xfff10100 0x100>;
+		};
+
+		L2: l2-cache {
+			compatible = "arm,pl310-cache";
+			reg = <0xfff12000 0x1000>;
+			interrupts = <0 70 4>;
+			cache-unified;
+			cache-level = <2>;
+		};
+
+		pmu {
+			compatible = "arm,cortex-a9-pmu";
+			interrupts = <0 76 4  0 75 4  0 74 4  0 73 4>;
+		};
+
+		sata@ffe08000 {
+			compatible = "calxeda,hb-ahci";
+			reg = <0xffe08000 0x10000>;
+			interrupts = <0 83 4>;
+		};
+
+		sdhci@ffe0e000 {
+			compatible = "calxeda,hb-sdhci";
+			reg = <0xffe0e000 0x1000>;
+			interrupts = <0 90 4>;
+		};
+
+		ipc@fff20000 {
+			compatible = "arm,pl320", "arm,primecell";
+			reg = <0xfff20000 0x1000>;
+			interrupts = <0 7 4>;
+		};
+
+		gpioe: gpio@fff30000 {
+			#gpio-cells = <2>;
+			compatible = "arm,pl061", "arm,primecell";
+			gpio-controller;
+			reg = <0xfff30000 0x1000>;
+			interrupts = <0 14 4>;
+		};
+
+		gpiof: gpio@fff31000 {
+			#gpio-cells = <2>;
+			compatible = "arm,pl061", "arm,primecell";
+			gpio-controller;
+			reg = <0xfff31000 0x1000>;
+			interrupts = <0 15 4>;
+		};
+
+		gpiog: gpio@fff32000 {
+			#gpio-cells = <2>;
+			compatible = "arm,pl061", "arm,primecell";
+			gpio-controller;
+			reg = <0xfff32000 0x1000>;
+			interrupts = <0 16 4>;
+		};
+
+		gpioh: gpio@fff33000 {
+			#gpio-cells = <2>;
+			compatible = "arm,pl061", "arm,primecell";
+			gpio-controller;
+			reg = <0xfff33000 0x1000>;
+			interrupts = <0 17 4>;
+		};
+
+		timer {
+			compatible = "arm,sp804", "arm,primecell";
+			reg = <0xfff34000 0x1000>;
+			interrupts = <0 18 4>;
+		};
+
+		rtc@fff35000 {
+			compatible = "arm,pl031", "arm,primecell";
+			reg = <0xfff35000 0x1000>;
+			interrupts = <0 19 4>;
+		};
+
+		serial@fff36000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0xfff36000 0x1000>;
+			interrupts = <0 20 4>;
+		};
+
+		smic@fff3a000 {
+			compatible = "ipmi-smic";
+			device_type = "ipmi";
+			reg = <0xfff3a000 0x1000>;
+			interrupts = <0 24 4>;
+			reg-size = <4>;
+			reg-spacing = <4>;
+		};
+
+		sregs@fff3c000 {
+			compatible = "calxeda,hb-sregs";
+			reg = <0xfff3c000 0x1000>;
+		};
+
+		dma@fff3d000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0xfff3d000 0x1000>;
+			interrupts = <0 92 4>;
+		};
+	};
+};
diff --git a/arch/arm/common/scoop.c b/arch/arm/common/scoop.c
index a07b0e763a80..1cde34a080d7 100644
--- a/arch/arm/common/scoop.c
+++ b/arch/arm/common/scoop.c
@@ -12,11 +12,11 @@
  */
 
 #include <linux/device.h>
+#include <linux/gpio.h>
 #include <linux/string.h>
 #include <linux/slab.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
-#include <asm/gpio.h>
 #include <asm/hardware/scoop.h>
 
 /* PCMCIA to Scoop linkage
diff --git a/arch/arm/include/asm/ecard.h b/arch/arm/include/asm/ecard.h
index 29f2610efc70..eaea14676d57 100644
--- a/arch/arm/include/asm/ecard.h
+++ b/arch/arm/include/asm/ecard.h
@@ -161,7 +161,6 @@ struct expansion_card {
 
 	/* Private internal data */
 	const char		*card_desc;	/* Card description		*/
-	CONST unsigned int	podaddr;	/* Base Linux address for card	*/
 	CONST loader_t		loader;		/* loader program */
 	u64			dma_mask;
 };
diff --git a/arch/arm/include/asm/gpio.h b/arch/arm/include/asm/gpio.h
index 166a7a3e2840..11ad0bfbb0ad 100644
--- a/arch/arm/include/asm/gpio.h
+++ b/arch/arm/include/asm/gpio.h
@@ -4,4 +4,23 @@
 /* not all ARM platforms necessarily support this API ... */
 #include <mach/gpio.h>
 
+#ifndef __ARM_GPIOLIB_COMPLEX
+/* Note: this may rely upon the value of ARCH_NR_GPIOS set in mach/gpio.h */
+#include <asm-generic/gpio.h>
+
+/* The trivial gpiolib dispatchers */
+#define gpio_get_value  __gpio_get_value
+#define gpio_set_value  __gpio_set_value
+#define gpio_cansleep   __gpio_cansleep
+#endif
+
+/*
+ * Provide a default gpio_to_irq() which should satisfy every case.
+ * However, some platforms want to do this differently, so allow them
+ * to override it.
+ */
+#ifndef gpio_to_irq
+#define gpio_to_irq	__gpio_to_irq
+#endif
+
 #endif /* _ARCH_ARM_GPIO_H */
diff --git a/arch/arm/include/asm/hardware/cache-l2x0.h b/arch/arm/include/asm/hardware/cache-l2x0.h
index 99a6ed7e1bfd..1db1143a9483 100644
--- a/arch/arm/include/asm/hardware/cache-l2x0.h
+++ b/arch/arm/include/asm/hardware/cache-l2x0.h
@@ -52,6 +52,8 @@
 #define L2X0_LOCKDOWN_WAY_D_BASE	0x900
 #define L2X0_LOCKDOWN_WAY_I_BASE	0x904
 #define L2X0_LOCKDOWN_STRIDE		0x08
+#define L2X0_ADDR_FILTER_START		0xC00
+#define L2X0_ADDR_FILTER_END		0xC04
 #define L2X0_TEST_OPERATION		0xF00
 #define L2X0_LINE_DATA			0xF10
 #define L2X0_LINE_TAG			0xF30
@@ -65,8 +67,23 @@
 #define L2X0_CACHE_ID_PART_MASK		(0xf << 6)
 #define L2X0_CACHE_ID_PART_L210		(1 << 6)
 #define L2X0_CACHE_ID_PART_L310		(3 << 6)
+#define L2X0_CACHE_ID_RTL_MASK          0x3f
+#define L2X0_CACHE_ID_RTL_R0P0          0x0
+#define L2X0_CACHE_ID_RTL_R1P0          0x2
+#define L2X0_CACHE_ID_RTL_R2P0          0x4
+#define L2X0_CACHE_ID_RTL_R3P0          0x5
+#define L2X0_CACHE_ID_RTL_R3P1          0x6
+#define L2X0_CACHE_ID_RTL_R3P2          0x8
 
 #define L2X0_AUX_CTRL_MASK			0xc0000fff
+#define L2X0_AUX_CTRL_DATA_RD_LATENCY_SHIFT	0
+#define L2X0_AUX_CTRL_DATA_RD_LATENCY_MASK	0x7
+#define L2X0_AUX_CTRL_DATA_WR_LATENCY_SHIFT	3
+#define L2X0_AUX_CTRL_DATA_WR_LATENCY_MASK	(0x7 << 3)
+#define L2X0_AUX_CTRL_TAG_LATENCY_SHIFT		6
+#define L2X0_AUX_CTRL_TAG_LATENCY_MASK		(0x7 << 6)
+#define L2X0_AUX_CTRL_DIRTY_LATENCY_SHIFT	9
+#define L2X0_AUX_CTRL_DIRTY_LATENCY_MASK	(0x7 << 9)
 #define L2X0_AUX_CTRL_ASSOCIATIVITY_SHIFT	16
 #define L2X0_AUX_CTRL_WAY_SIZE_SHIFT		17
 #define L2X0_AUX_CTRL_WAY_SIZE_MASK		(0x7 << 17)
@@ -77,8 +94,40 @@
 #define L2X0_AUX_CTRL_INSTR_PREFETCH_SHIFT	29
 #define L2X0_AUX_CTRL_EARLY_BRESP_SHIFT		30
 
+#define L2X0_LATENCY_CTRL_SETUP_SHIFT	0
+#define L2X0_LATENCY_CTRL_RD_SHIFT	4
+#define L2X0_LATENCY_CTRL_WR_SHIFT	8
+
+#define L2X0_ADDR_FILTER_EN		1
+
 #ifndef __ASSEMBLY__
 extern void __init l2x0_init(void __iomem *base, __u32 aux_val, __u32 aux_mask);
+#if defined(CONFIG_CACHE_L2X0) && defined(CONFIG_OF)
+extern int l2x0_of_init(__u32 aux_val, __u32 aux_mask);
+#else
+static inline int l2x0_of_init(__u32 aux_val, __u32 aux_mask)
+{
+	return -ENODEV;
+}
 #endif
 
+struct l2x0_regs {
+	unsigned long phy_base;
+	unsigned long aux_ctrl;
+	/*
+	 * Whether the following registers need to be saved/restored
+	 * depends on platform
+	 */
+	unsigned long tag_latency;
+	unsigned long data_latency;
+	unsigned long filter_start;
+	unsigned long filter_end;
+	unsigned long prefetch_ctrl;
+	unsigned long pwr_ctrl;
+};
+
+extern struct l2x0_regs l2x0_saved_regs;
+
+#endif /* __ASSEMBLY__ */
+
 #endif
diff --git a/arch/arm/include/asm/hardware/iop3xx-gpio.h b/arch/arm/include/asm/hardware/iop3xx-gpio.h
index b69d972b1f7d..9eda7dc92ad8 100644
--- a/arch/arm/include/asm/hardware/iop3xx-gpio.h
+++ b/arch/arm/include/asm/hardware/iop3xx-gpio.h
@@ -28,6 +28,8 @@
 #include <mach/hardware.h>
 #include <asm-generic/gpio.h>
 
+#define __ARM_GPIOLIB_COMPLEX
+
 #define IOP3XX_N_GPIOS	8
 
 static inline int gpio_get_value(unsigned gpio)
diff --git a/arch/arm/include/asm/io.h b/arch/arm/include/asm/io.h
index d66605dea55a..ffb089d46a17 100644
--- a/arch/arm/include/asm/io.h
+++ b/arch/arm/include/asm/io.h
@@ -110,6 +110,27 @@ static inline void __iomem *__typesafe_io(unsigned long addr)
 #include <mach/io.h>
 
 /*
+ * This is the limit of PC card/PCI/ISA IO space, which is by default
+ * 64K if we have PC card, PCI or ISA support.  Otherwise, default to
+ * zero to prevent ISA/PCI drivers claiming IO space (and potentially
+ * oopsing.)
+ *
+ * Only set this larger if you really need inb() et.al. to operate over
+ * a larger address space.  Note that SOC_COMMON ioremaps each sockets
+ * IO space area, and so inb() et.al. must be defined to operate as per
+ * readb() et.al. on such platforms.
+ */
+#ifndef IO_SPACE_LIMIT
+#if defined(CONFIG_PCMCIA_SOC_COMMON) || defined(CONFIG_PCMCIA_SOC_COMMON_MODULE)
+#define IO_SPACE_LIMIT ((resource_size_t)0xffffffff)
+#elif defined(CONFIG_PCI) || defined(CONFIG_ISA) || defined(CONFIG_PCCARD)
+#define IO_SPACE_LIMIT ((resource_size_t)0xffff)
+#else
+#define IO_SPACE_LIMIT ((resource_size_t)0)
+#endif
+#endif
+
+/*
  *  IO port access primitives
  *  -------------------------
  *
diff --git a/arch/arm/include/asm/outercache.h b/arch/arm/include/asm/outercache.h
index d8387437ec5a..53426c66352a 100644
--- a/arch/arm/include/asm/outercache.h
+++ b/arch/arm/include/asm/outercache.h
@@ -34,6 +34,7 @@ struct outer_cache_fns {
 	void (*sync)(void);
 #endif
 	void (*set_debug)(unsigned long);
+	void (*resume)(void);
 };
 
 #ifdef CONFIG_OUTER_CACHE
@@ -74,6 +75,12 @@ static inline void outer_disable(void)
 		outer_cache.disable();
 }
 
+static inline void outer_resume(void)
+{
+	if (outer_cache.resume)
+		outer_cache.resume();
+}
+
 #else
 
 static inline void outer_inv_range(phys_addr_t start, phys_addr_t end)
diff --git a/arch/arm/kernel/asm-offsets.c b/arch/arm/kernel/asm-offsets.c
index 16baba2e4369..1429d8989fb9 100644
--- a/arch/arm/kernel/asm-offsets.c
+++ b/arch/arm/kernel/asm-offsets.c
@@ -20,6 +20,7 @@
 #include <asm/thread_info.h>
 #include <asm/memory.h>
 #include <asm/procinfo.h>
+#include <asm/hardware/cache-l2x0.h>
 #include <linux/kbuild.h>
 
 /*
@@ -92,6 +93,17 @@ int main(void)
   DEFINE(S_OLD_R0,		offsetof(struct pt_regs, ARM_ORIG_r0));
   DEFINE(S_FRAME_SIZE,		sizeof(struct pt_regs));
   BLANK();
+#ifdef CONFIG_CACHE_L2X0
+  DEFINE(L2X0_R_PHY_BASE,	offsetof(struct l2x0_regs, phy_base));
+  DEFINE(L2X0_R_AUX_CTRL,	offsetof(struct l2x0_regs, aux_ctrl));
+  DEFINE(L2X0_R_TAG_LATENCY,	offsetof(struct l2x0_regs, tag_latency));
+  DEFINE(L2X0_R_DATA_LATENCY,	offsetof(struct l2x0_regs, data_latency));
+  DEFINE(L2X0_R_FILTER_START,	offsetof(struct l2x0_regs, filter_start));
+  DEFINE(L2X0_R_FILTER_END,	offsetof(struct l2x0_regs, filter_end));
+  DEFINE(L2X0_R_PREFETCH_CTRL,	offsetof(struct l2x0_regs, prefetch_ctrl));
+  DEFINE(L2X0_R_PWR_CTRL,	offsetof(struct l2x0_regs, pwr_ctrl));
+  BLANK();
+#endif
 #ifdef CONFIG_CPU_HAS_ASID
   DEFINE(MM_CONTEXT_ID,		offsetof(struct mm_struct, context.id));
   BLANK();
diff --git a/arch/arm/kernel/ecard.c b/arch/arm/kernel/ecard.c
index d16500110ee9..4dd0edab6a65 100644
--- a/arch/arm/kernel/ecard.c
+++ b/arch/arm/kernel/ecard.c
@@ -237,7 +237,7 @@ static void ecard_init_pgtables(struct mm_struct *mm)
 
 	memcpy(dst_pgd, src_pgd, sizeof(pgd_t) * (IO_SIZE / PGDIR_SIZE));
 
-	src_pgd = pgd_offset(mm, EASI_BASE);
+	src_pgd = pgd_offset(mm, (unsigned long)EASI_BASE);
 	dst_pgd = pgd_offset(mm, EASI_START);
 
 	memcpy(dst_pgd, src_pgd, sizeof(pgd_t) * (EASI_SIZE / PGDIR_SIZE));
@@ -674,44 +674,37 @@ static int __init ecard_probeirqhw(void)
 #define ecard_probeirqhw() (0)
 #endif
 
-#ifndef IO_EC_MEMC8_BASE
-#define IO_EC_MEMC8_BASE 0
-#endif
-
-static unsigned int __ecard_address(ecard_t *ec, card_type_t type, card_speed_t speed)
+static void __iomem *__ecard_address(ecard_t *ec, card_type_t type, card_speed_t speed)
 {
-	unsigned long address = 0;
+	void __iomem *address = NULL;
 	int slot = ec->slot_no;
 
 	if (ec->slot_no == 8)
-		return IO_EC_MEMC8_BASE;
+		return ECARD_MEMC8_BASE;
 
 	ectcr &= ~(1 << slot);
 
 	switch (type) {
 	case ECARD_MEMC:
 		if (slot < 4)
-			address = IO_EC_MEMC_BASE + (slot << 12);
+			address = ECARD_MEMC_BASE + (slot << 14);
 		break;
 
 	case ECARD_IOC:
 		if (slot < 4)
-			address = IO_EC_IOC_BASE + (slot << 12);
-#ifdef IO_EC_IOC4_BASE
+			address = ECARD_IOC_BASE + (slot << 14);
 		else
-			address = IO_EC_IOC4_BASE + ((slot - 4) << 12);
-#endif
+			address = ECARD_IOC4_BASE + ((slot - 4) << 14);
 		if (address)
-			address +=  speed << 17;
+			address += speed << 19;
 		break;
 
-#ifdef IO_EC_EASI_BASE
 	case ECARD_EASI:
-		address = IO_EC_EASI_BASE + (slot << 22);
+		address = ECARD_EASI_BASE + (slot << 24);
 		if (speed == ECARD_FAST)
 			ectcr |= 1 << slot;
 		break;
-#endif
+
 	default:
 		break;
 	}
@@ -990,6 +983,7 @@ ecard_probe(int slot, card_type_t type)
 	ecard_t **ecp;
 	ecard_t *ec;
 	struct ex_ecid cid;
+	void __iomem *addr;
 	int i, rc;
 
 	ec = ecard_alloc_card(type, slot);
@@ -999,7 +993,7 @@ ecard_probe(int slot, card_type_t type)
 	}
 
 	rc = -ENODEV;
-	if ((ec->podaddr = __ecard_address(ec, type, ECARD_SYNC)) == 0)
+	if ((addr = __ecard_address(ec, type, ECARD_SYNC)) == NULL)
 		goto nodev;
 
 	cid.r_zero = 1;
@@ -1019,7 +1013,7 @@ ecard_probe(int slot, card_type_t type)
 	ec->cid.fiqmask = cid.r_fiqmask;
 	ec->cid.fiqoff  = ecard_gets24(cid.r_fiqoff);
 	ec->fiqaddr	=
-	ec->irqaddr	= (void __iomem *)ioaddr(ec->podaddr);
+	ec->irqaddr	= addr;
 
 	if (ec->cid.is) {
 		ec->irqmask = ec->cid.irqmask;
@@ -1048,10 +1042,8 @@ ecard_probe(int slot, card_type_t type)
 		set_irq_flags(ec->irq, IRQF_VALID);
 	}
 
-#ifdef IO_EC_MEMC8_BASE
 	if (slot == 8)
 		ec->irq = 11;
-#endif
 #ifdef CONFIG_ARCH_RPC
 	/* On RiscPC, only first two slots have DMA capability */
 	if (slot < 2)
@@ -1097,9 +1089,7 @@ static int __init ecard_init(void)
 			ecard_probe(slot, ECARD_IOC);
 	}
 
-#ifdef IO_EC_MEMC8_BASE
 	ecard_probe(8, ECARD_IOC);
-#endif
 
 	irqhw = ecard_probeirqhw();
 
diff --git a/arch/arm/mach-at91/at91cap9_devices.c b/arch/arm/mach-at91/at91cap9_devices.c
index dba0d8d8a4bd..f87f5040e78e 100644
--- a/arch/arm/mach-at91/at91cap9_devices.c
+++ b/arch/arm/mach-at91/at91cap9_devices.c
@@ -16,6 +16,7 @@
 #include <asm/mach/irq.h>
 
 #include <linux/dma-mapping.h>
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/i2c-gpio.h>
 
@@ -23,7 +24,6 @@
 
 #include <mach/board.h>
 #include <mach/cpu.h>
-#include <mach/gpio.h>
 #include <mach/at91cap9.h>
 #include <mach/at91cap9_matrix.h>
 #include <mach/at91sam9_smc.h>
diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c
index 7227755ffec6..978be950035a 100644
--- a/arch/arm/mach-at91/at91rm9200_devices.c
+++ b/arch/arm/mach-at91/at91rm9200_devices.c
@@ -14,11 +14,11 @@
 #include <asm/mach/map.h>
 
 #include <linux/dma-mapping.h>
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/i2c-gpio.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91rm9200.h>
 #include <mach/at91rm9200_mc.h>
 
diff --git a/arch/arm/mach-at91/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c
index 39f81f47b4ba..a53b3de9daa2 100644
--- a/arch/arm/mach-at91/at91sam9260_devices.c
+++ b/arch/arm/mach-at91/at91sam9260_devices.c
@@ -13,11 +13,11 @@
 #include <asm/mach/map.h>
 
 #include <linux/dma-mapping.h>
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/i2c-gpio.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/cpu.h>
 #include <mach/at91sam9260.h>
 #include <mach/at91sam9260_matrix.h>
diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c
index 0f917928eeb7..4e647b653339 100644
--- a/arch/arm/mach-at91/at91sam9261_devices.c
+++ b/arch/arm/mach-at91/at91sam9261_devices.c
@@ -14,6 +14,7 @@
 #include <asm/mach/map.h>
 
 #include <linux/dma-mapping.h>
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/i2c-gpio.h>
 
@@ -21,7 +22,6 @@
 #include <video/atmel_lcdc.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9261.h>
 #include <mach/at91sam9261_matrix.h>
 #include <mach/at91sam9_smc.h>
diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c
index a050f41fc860..dd7662bc395f 100644
--- a/arch/arm/mach-at91/at91sam9263_devices.c
+++ b/arch/arm/mach-at91/at91sam9263_devices.c
@@ -13,6 +13,7 @@
 #include <asm/mach/map.h>
 
 #include <linux/dma-mapping.h>
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/i2c-gpio.h>
 
@@ -20,7 +21,6 @@
 #include <video/atmel_lcdc.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9263.h>
 #include <mach/at91sam9263_matrix.h>
 #include <mach/at91sam9_smc.h>
diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c
index 600bffb01edb..c3dfb1b3b1e3 100644
--- a/arch/arm/mach-at91/at91sam9g45_devices.c
+++ b/arch/arm/mach-at91/at91sam9g45_devices.c
@@ -13,6 +13,7 @@
 #include <asm/mach/map.h>
 
 #include <linux/dma-mapping.h>
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/i2c-gpio.h>
 #include <linux/atmel-mci.h>
@@ -21,7 +22,6 @@
 #include <video/atmel_lcdc.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9g45.h>
 #include <mach/at91sam9g45_matrix.h>
 #include <mach/at91sam9_smc.h>
diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c
index aacb19dc9225..305a851b5bff 100644
--- a/arch/arm/mach-at91/at91sam9rl_devices.c
+++ b/arch/arm/mach-at91/at91sam9rl_devices.c
@@ -10,6 +10,7 @@
 #include <asm/mach/map.h>
 
 #include <linux/dma-mapping.h>
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/i2c-gpio.h>
 
@@ -17,7 +18,6 @@
 #include <video/atmel_lcdc.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9rl.h>
 #include <mach/at91sam9rl_matrix.h>
 #include <mach/at91sam9_smc.h>
diff --git a/arch/arm/mach-at91/board-1arm.c b/arch/arm/mach-at91/board-1arm.c
index 5aa58851eb39..367d5cd5e362 100644
--- a/arch/arm/mach-at91/board-1arm.c
+++ b/arch/arm/mach-at91/board-1arm.c
@@ -19,6 +19,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -34,7 +35,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/cpu.h>
 
 #include "generic.h"
diff --git a/arch/arm/mach-at91/board-afeb-9260v1.c b/arch/arm/mach-at91/board-afeb-9260v1.c
index b0c796d42e49..0487ea10c2d6 100644
--- a/arch/arm/mach-at91/board-afeb-9260v1.c
+++ b/arch/arm/mach-at91/board-afeb-9260v1.c
@@ -25,6 +25,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -43,7 +44,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 
 #include "generic.h"
 
diff --git a/arch/arm/mach-at91/board-cam60.c b/arch/arm/mach-at91/board-cam60.c
index d1abd5898e85..747b2eaa9737 100644
--- a/arch/arm/mach-at91/board-cam60.c
+++ b/arch/arm/mach-at91/board-cam60.c
@@ -21,6 +21,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -38,7 +39,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 
 #include "sam9_smc.h"
diff --git a/arch/arm/mach-at91/board-cap9adk.c b/arch/arm/mach-at91/board-cap9adk.c
index 679b0b743e92..062670351a6a 100644
--- a/arch/arm/mach-at91/board-cap9adk.c
+++ b/arch/arm/mach-at91/board-cap9adk.c
@@ -22,6 +22,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -41,7 +42,6 @@
 #include <asm/mach/map.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91cap9_matrix.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/system_rev.h>
diff --git a/arch/arm/mach-at91/board-carmeva.c b/arch/arm/mach-at91/board-carmeva.c
index c578c5d90728..774c87fcbd5b 100644
--- a/arch/arm/mach-at91/board-carmeva.c
+++ b/arch/arm/mach-at91/board-carmeva.c
@@ -20,6 +20,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -35,7 +36,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 
 #include "generic.h"
 
diff --git a/arch/arm/mach-at91/board-cpu9krea.c b/arch/arm/mach-at91/board-cpu9krea.c
index f4da8a16d5dc..fc885a4ce243 100644
--- a/arch/arm/mach-at91/board-cpu9krea.c
+++ b/arch/arm/mach-at91/board-cpu9krea.c
@@ -21,6 +21,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -40,7 +41,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91sam9260_matrix.h>
 
diff --git a/arch/arm/mach-at91/board-cpuat91.c b/arch/arm/mach-at91/board-cpuat91.c
index 2d919f5a4f57..d35e65b08ccd 100644
--- a/arch/arm/mach-at91/board-cpuat91.c
+++ b/arch/arm/mach-at91/board-cpuat91.c
@@ -19,6 +19,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -36,7 +37,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91rm9200_mc.h>
 #include <mach/cpu.h>
 
diff --git a/arch/arm/mach-at91/board-csb337.c b/arch/arm/mach-at91/board-csb337.c
index 17654d5e94e6..c3936665e645 100644
--- a/arch/arm/mach-at91/board-csb337.c
+++ b/arch/arm/mach-at91/board-csb337.c
@@ -19,6 +19,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -38,7 +39,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 
 #include "generic.h"
 
diff --git a/arch/arm/mach-at91/board-csb637.c b/arch/arm/mach-at91/board-csb637.c
index 72b55674616c..586100e2acbb 100644
--- a/arch/arm/mach-at91/board-csb637.c
+++ b/arch/arm/mach-at91/board-csb637.c
@@ -20,6 +20,7 @@
 
 #include <linux/types.h>
 #include <linux/init.h>
+#include <linux/gpio.h>
 #include <linux/mm.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
@@ -35,7 +36,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 
 #include "generic.h"
 
diff --git a/arch/arm/mach-at91/board-eb9200.c b/arch/arm/mach-at91/board-eb9200.c
index 01170a2766a8..45db7a3dbef0 100644
--- a/arch/arm/mach-at91/board-eb9200.c
+++ b/arch/arm/mach-at91/board-eb9200.c
@@ -20,6 +20,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -35,7 +36,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 
 #include "generic.h"
 
diff --git a/arch/arm/mach-at91/board-ecbat91.c b/arch/arm/mach-at91/board-ecbat91.c
index 7c0313c51f26..2f9c16d29212 100644
--- a/arch/arm/mach-at91/board-ecbat91.c
+++ b/arch/arm/mach-at91/board-ecbat91.c
@@ -20,6 +20,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -37,7 +38,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/cpu.h>
 
 #include "generic.h"
diff --git a/arch/arm/mach-at91/board-kafa.c b/arch/arm/mach-at91/board-kafa.c
index 4a170890b3b1..3bae73e63633 100644
--- a/arch/arm/mach-at91/board-kafa.c
+++ b/arch/arm/mach-at91/board-kafa.c
@@ -19,6 +19,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -34,7 +35,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/cpu.h>
 
 #include "generic.h"
diff --git a/arch/arm/mach-at91/board-kb9202.c b/arch/arm/mach-at91/board-kb9202.c
index 9dc8d496ead1..15a3f1a87ab0 100644
--- a/arch/arm/mach-at91/board-kb9202.c
+++ b/arch/arm/mach-at91/board-kb9202.c
@@ -20,6 +20,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -35,7 +36,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/cpu.h>
 #include <mach/at91rm9200_mc.h>
 
diff --git a/arch/arm/mach-at91/board-neocore926.c b/arch/arm/mach-at91/board-neocore926.c
index 9bc6ab32e0ac..6094496f7edb 100644
--- a/arch/arm/mach-at91/board-neocore926.c
+++ b/arch/arm/mach-at91/board-neocore926.c
@@ -21,6 +21,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -44,7 +45,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 
 #include "sam9_smc.h"
diff --git a/arch/arm/mach-at91/board-picotux200.c b/arch/arm/mach-at91/board-picotux200.c
index b7b8390e8a00..0a8fe6a1b7c8 100644
--- a/arch/arm/mach-at91/board-picotux200.c
+++ b/arch/arm/mach-at91/board-picotux200.c
@@ -20,6 +20,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -37,7 +38,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91rm9200_mc.h>
 
 #include "generic.h"
diff --git a/arch/arm/mach-at91/board-qil-a9260.c b/arch/arm/mach-at91/board-qil-a9260.c
index 81f911033681..938cc390bea3 100644
--- a/arch/arm/mach-at91/board-qil-a9260.c
+++ b/arch/arm/mach-at91/board-qil-a9260.c
@@ -21,6 +21,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -40,7 +41,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 
diff --git a/arch/arm/mach-at91/board-rm9200dk.c b/arch/arm/mach-at91/board-rm9200dk.c
index 6f08faadb474..b4ac30e38a9e 100644
--- a/arch/arm/mach-at91/board-rm9200dk.c
+++ b/arch/arm/mach-at91/board-rm9200dk.c
@@ -22,6 +22,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -39,7 +40,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91rm9200_mc.h>
 
 #include "generic.h"
diff --git a/arch/arm/mach-at91/board-rm9200ek.c b/arch/arm/mach-at91/board-rm9200ek.c
index 85bcccd7b9e4..99fd7f8aee0e 100644
--- a/arch/arm/mach-at91/board-rm9200ek.c
+++ b/arch/arm/mach-at91/board-rm9200ek.c
@@ -22,6 +22,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -39,7 +40,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91rm9200_mc.h>
 
 #include "generic.h"
diff --git a/arch/arm/mach-at91/board-sam9-l9260.c b/arch/arm/mach-at91/board-sam9-l9260.c
index 4d3a02f1289e..2a21e790250e 100644
--- a/arch/arm/mach-at91/board-sam9-l9260.c
+++ b/arch/arm/mach-at91/board-sam9-l9260.c
@@ -21,6 +21,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -37,7 +38,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 
 #include "sam9_smc.h"
diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c
index 8a50c3e67186..89c8b579bfda 100644
--- a/arch/arm/mach-at91/board-sam9260ek.c
+++ b/arch/arm/mach-at91/board-sam9260ek.c
@@ -20,6 +20,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -41,7 +42,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 #include <mach/system_rev.h>
diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c
index 5096a0ec50c1..3741f43cdae9 100644
--- a/arch/arm/mach-at91/board-sam9261ek.c
+++ b/arch/arm/mach-at91/board-sam9261ek.c
@@ -20,6 +20,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -45,7 +46,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 #include <mach/system_rev.h>
diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c
index ea8f185d3b9d..a580dd451a41 100644
--- a/arch/arm/mach-at91/board-sam9263ek.c
+++ b/arch/arm/mach-at91/board-sam9263ek.c
@@ -20,6 +20,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -44,7 +45,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 #include <mach/system_rev.h>
diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c
index 817f59d7251b..8d77c2ff96b2 100644
--- a/arch/arm/mach-at91/board-sam9g20ek.c
+++ b/arch/arm/mach-at91/board-sam9g20ek.c
@@ -18,6 +18,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -41,7 +42,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/system_rev.h>
 
diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c
index ad234ccbf57e..2d6203ac1a42 100644
--- a/arch/arm/mach-at91/board-sam9m10g45ek.c
+++ b/arch/arm/mach-at91/board-sam9m10g45ek.c
@@ -14,6 +14,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -38,7 +39,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 #include <mach/system_rev.h>
diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c
index 4f14b54b93a8..39a28effc3df 100644
--- a/arch/arm/mach-at91/board-sam9rlek.c
+++ b/arch/arm/mach-at91/board-sam9rlek.c
@@ -8,6 +8,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -30,7 +31,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 
diff --git a/arch/arm/mach-at91/board-usb-a9260.c b/arch/arm/mach-at91/board-usb-a9260.c
index 8c4c1a02c4be..bac9b65cf551 100644
--- a/arch/arm/mach-at91/board-usb-a9260.c
+++ b/arch/arm/mach-at91/board-usb-a9260.c
@@ -21,6 +21,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -40,7 +41,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 
diff --git a/arch/arm/mach-at91/board-usb-a9263.c b/arch/arm/mach-at91/board-usb-a9263.c
index 25e793782a4e..5bd735787d6d 100644
--- a/arch/arm/mach-at91/board-usb-a9263.c
+++ b/arch/arm/mach-at91/board-usb-a9263.c
@@ -21,6 +21,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -39,7 +40,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 
diff --git a/arch/arm/mach-at91/board-yl-9200.c b/arch/arm/mach-at91/board-yl-9200.c
index 95edcbd2aec6..3c288b396fc4 100644
--- a/arch/arm/mach-at91/board-yl-9200.c
+++ b/arch/arm/mach-at91/board-yl-9200.c
@@ -22,6 +22,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -43,7 +44,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91rm9200_mc.h>
 #include <mach/cpu.h>
 
diff --git a/arch/arm/mach-at91/gpio.c b/arch/arm/mach-at91/gpio.c
index 4615528205c8..224e9e2f8674 100644
--- a/arch/arm/mach-at91/gpio.c
+++ b/arch/arm/mach-at91/gpio.c
@@ -11,6 +11,7 @@
 
 #include <linux/clk.h>
 #include <linux/errno.h>
+#include <linux/gpio.h>
 #include <linux/interrupt.h>
 #include <linux/irq.h>
 #include <linux/debugfs.h>
@@ -22,9 +23,6 @@
 
 #include <mach/hardware.h>
 #include <mach/at91_pio.h>
-#include <mach/gpio.h>
-
-#include <asm/gpio.h>
 
 #include "generic.h"
 
diff --git a/arch/arm/mach-at91/include/mach/gpio.h b/arch/arm/mach-at91/include/mach/gpio.h
index 056dc6674b6b..2b9a1f51210f 100644
--- a/arch/arm/mach-at91/include/mach/gpio.h
+++ b/arch/arm/mach-at91/include/mach/gpio.h
@@ -214,11 +214,6 @@ extern void at91_gpio_resume(void);
  */
 
 #include <asm/errno.h>
-#include <asm-generic/gpio.h>		/* cansleep wrappers */
-
-#define gpio_get_value	__gpio_get_value
-#define gpio_set_value	__gpio_set_value
-#define gpio_cansleep	__gpio_cansleep
 
 #define gpio_to_irq(gpio) (gpio)
 #define irq_to_gpio(irq)  (irq)
diff --git a/arch/arm/mach-at91/leds.c b/arch/arm/mach-at91/leds.c
index 0415a839e1ad..8dfafe76ffe6 100644
--- a/arch/arm/mach-at91/leds.c
+++ b/arch/arm/mach-at91/leds.c
@@ -9,13 +9,13 @@
  * 2 of the License, or (at your option) any later version.
 */
 
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 
 
 /* ------------------------------------------------------------------------- */
diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
index 4159eca78945..7046158109d7 100644
--- a/arch/arm/mach-at91/pm.c
+++ b/arch/arm/mach-at91/pm.c
@@ -10,6 +10,7 @@
  * (at your option) any later version.
  */
 
+#include <linux/gpio.h>
 #include <linux/suspend.h>
 #include <linux/sched.h>
 #include <linux/proc_fs.h>
@@ -25,7 +26,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/at91_pmc.h>
-#include <mach/gpio.h>
 #include <mach/cpu.h>
 
 #include "generic.h"
diff --git a/arch/arm/mach-davinci/Makefile b/arch/arm/mach-davinci/Makefile
index 0b87a1ca2bb3..495e31306fc0 100644
--- a/arch/arm/mach-davinci/Makefile
+++ b/arch/arm/mach-davinci/Makefile
@@ -5,7 +5,7 @@
 
 # Common objects
 obj-y 			:= time.o clock.o serial.o io.o psc.o \
-			   gpio.o dma.o usb.o common.o sram.o aemif.o
+			   dma.o usb.o common.o sram.o aemif.o
 
 obj-$(CONFIG_DAVINCI_MUX)		+= mux.o
 
@@ -17,7 +17,6 @@ obj-$(CONFIG_ARCH_DAVINCI_DM365)	+= dm365.o devices.o
 obj-$(CONFIG_ARCH_DAVINCI_DA830)        += da830.o devices-da8xx.o
 obj-$(CONFIG_ARCH_DAVINCI_DA850)        += da850.o devices-da8xx.o
 obj-$(CONFIG_ARCH_DAVINCI_TNETV107X)    += tnetv107x.o devices-tnetv107x.o
-obj-$(CONFIG_ARCH_DAVINCI_TNETV107X)    += gpio-tnetv107x.o
 
 obj-$(CONFIG_AINTC)			+= irq.o
 obj-$(CONFIG_CP_INTC)			+= cp_intc.o
diff --git a/arch/arm/mach-davinci/da830.c b/arch/arm/mach-davinci/da830.c
index 2ed2f822fc40..a6bf5dcaef13 100644
--- a/arch/arm/mach-davinci/da830.c
+++ b/arch/arm/mach-davinci/da830.c
@@ -8,6 +8,7 @@
  * is licensed "as is" without any warranty of any kind, whether express
  * or implied.
  */
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/clk.h>
 
@@ -19,7 +20,7 @@
 #include <mach/common.h>
 #include <mach/time.h>
 #include <mach/da8xx.h>
-#include <mach/gpio.h>
+#include <mach/gpio-davinci.h>
 
 #include "clock.h"
 #include "mux.h"
diff --git a/arch/arm/mach-davinci/da850.c b/arch/arm/mach-davinci/da850.c
index 935dbed5c541..4aae01576aab 100644
--- a/arch/arm/mach-davinci/da850.c
+++ b/arch/arm/mach-davinci/da850.c
@@ -11,6 +11,7 @@
  * is licensed "as is" without any warranty of any kind, whether express
  * or implied.
  */
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/clk.h>
 #include <linux/platform_device.h>
@@ -27,7 +28,7 @@
 #include <mach/da8xx.h>
 #include <mach/cpufreq.h>
 #include <mach/pm.h>
-#include <mach/gpio.h>
+#include <mach/gpio-davinci.h>
 
 #include "clock.h"
 #include "mux.h"
diff --git a/arch/arm/mach-davinci/dm355.c b/arch/arm/mach-davinci/dm355.c
index a3a94e9c9378..c143f43addcc 100644
--- a/arch/arm/mach-davinci/dm355.c
+++ b/arch/arm/mach-davinci/dm355.c
@@ -13,7 +13,6 @@
 #include <linux/serial_8250.h>
 #include <linux/platform_device.h>
 #include <linux/dma-mapping.h>
-#include <linux/gpio.h>
 
 #include <linux/spi/spi.h>
 
@@ -30,6 +29,7 @@
 #include <mach/common.h>
 #include <mach/asp.h>
 #include <mach/spi.h>
+#include <mach/gpio-davinci.h>
 
 #include "clock.h"
 #include "mux.h"
diff --git a/arch/arm/mach-davinci/dm365.c b/arch/arm/mach-davinci/dm365.c
index 4604e72d7d99..679e168dce34 100644
--- a/arch/arm/mach-davinci/dm365.c
+++ b/arch/arm/mach-davinci/dm365.c
@@ -17,7 +17,6 @@
 #include <linux/serial_8250.h>
 #include <linux/platform_device.h>
 #include <linux/dma-mapping.h>
-#include <linux/gpio.h>
 #include <linux/spi/spi.h>
 
 #include <asm/mach/map.h>
@@ -34,7 +33,7 @@
 #include <mach/asp.h>
 #include <mach/keyscan.h>
 #include <mach/spi.h>
-
+#include <mach/gpio-davinci.h>
 
 #include "clock.h"
 #include "mux.h"
diff --git a/arch/arm/mach-davinci/dm644x.c b/arch/arm/mach-davinci/dm644x.c
index 4c82c2716293..9a274665edc5 100644
--- a/arch/arm/mach-davinci/dm644x.c
+++ b/arch/arm/mach-davinci/dm644x.c
@@ -12,7 +12,6 @@
 #include <linux/clk.h>
 #include <linux/serial_8250.h>
 #include <linux/platform_device.h>
-#include <linux/gpio.h>
 
 #include <asm/mach/map.h>
 
@@ -26,6 +25,7 @@
 #include <mach/serial.h>
 #include <mach/common.h>
 #include <mach/asp.h>
+#include <mach/gpio-davinci.h>
 
 #include "clock.h"
 #include "mux.h"
diff --git a/arch/arm/mach-davinci/dm646x.c b/arch/arm/mach-davinci/dm646x.c
index 1802e711a2b8..03e5f4931b42 100644
--- a/arch/arm/mach-davinci/dm646x.c
+++ b/arch/arm/mach-davinci/dm646x.c
@@ -13,7 +13,6 @@
 #include <linux/clk.h>
 #include <linux/serial_8250.h>
 #include <linux/platform_device.h>
-#include <linux/gpio.h>
 
 #include <asm/mach/map.h>
 
@@ -27,6 +26,7 @@
 #include <mach/serial.h>
 #include <mach/common.h>
 #include <mach/asp.h>
+#include <mach/gpio-davinci.h>
 
 #include "clock.h"
 #include "mux.h"
diff --git a/arch/arm/mach-davinci/include/mach/gpio-davinci.h b/arch/arm/mach-davinci/include/mach/gpio-davinci.h
new file mode 100644
index 000000000000..1fdd1fd35448
--- /dev/null
+++ b/arch/arm/mach-davinci/include/mach/gpio-davinci.h
@@ -0,0 +1,91 @@
+/*
+ * TI DaVinci GPIO Support
+ *
+ * Copyright (c) 2006 David Brownell
+ * Copyright (c) 2007, MontaVista Software, Inc. <source@mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef	__DAVINCI_DAVINCI_GPIO_H
+#define	__DAVINCI_DAVINCI_GPIO_H
+
+#include <linux/io.h>
+#include <linux/spinlock.h>
+
+#include <asm-generic/gpio.h>
+
+#include <mach/irqs.h>
+#include <mach/common.h>
+
+#define DAVINCI_GPIO_BASE 0x01C67000
+
+enum davinci_gpio_type {
+	GPIO_TYPE_DAVINCI = 0,
+	GPIO_TYPE_TNETV107X,
+};
+
+/*
+ * basic gpio routines
+ *
+ * board-specific init should be done by arch/.../.../board-XXX.c (maybe
+ * initializing banks together) rather than boot loaders; kexec() won't
+ * go through boot loaders.
+ *
+ * the gpio clock will be turned on when gpios are used, and you may also
+ * need to pay attention to PINMUX registers to be sure those pins are
+ * used as gpios, not with other peripherals.
+ *
+ * On-chip GPIOs are numbered 0..(DAVINCI_N_GPIO-1).  For documentation,
+ * and maybe for later updates, code may write GPIO(N).  These may be
+ * all 1.8V signals, all 3.3V ones, or a mix of the two.  A given chip
+ * may not support all the GPIOs in that range.
+ *
+ * GPIOs can also be on external chips, numbered after the ones built-in
+ * to the DaVinci chip.  For now, they won't be usable as IRQ sources.
+ */
+#define	GPIO(X)		(X)		/* 0 <= X <= (DAVINCI_N_GPIO - 1) */
+
+/* Convert GPIO signal to GPIO pin number */
+#define GPIO_TO_PIN(bank, gpio)	(16 * (bank) + (gpio))
+
+struct davinci_gpio_controller {
+	struct gpio_chip	chip;
+	int			irq_base;
+	spinlock_t		lock;
+	void __iomem		*regs;
+	void __iomem		*set_data;
+	void __iomem		*clr_data;
+	void __iomem		*in_data;
+};
+
+/* The __gpio_to_controller() and __gpio_mask() functions inline to constants
+ * with constant parameters; or in outlined code they execute at runtime.
+ *
+ * You'd access the controller directly when reading or writing more than
+ * one gpio value at a time, and to support wired logic where the value
+ * being driven by the cpu need not match the value read back.
+ *
+ * These are NOT part of the cross-platform GPIO interface
+ */
+static inline struct davinci_gpio_controller *
+__gpio_to_controller(unsigned gpio)
+{
+	struct davinci_gpio_controller *ctlrs = davinci_soc_info.gpio_ctlrs;
+	int index = gpio / 32;
+
+	if (!ctlrs || index >= davinci_soc_info.gpio_ctlrs_num)
+		return NULL;
+
+	return ctlrs + index;
+}
+
+static inline u32 __gpio_mask(unsigned gpio)
+{
+	return 1 << (gpio % 32);
+}
+
+#endif	/* __DAVINCI_DAVINCI_GPIO_H */
diff --git a/arch/arm/mach-davinci/include/mach/gpio.h b/arch/arm/mach-davinci/include/mach/gpio.h
index fbece126c2bf..fbaae4772b91 100644
--- a/arch/arm/mach-davinci/include/mach/gpio.h
+++ b/arch/arm/mach-davinci/include/mach/gpio.h
@@ -13,80 +13,10 @@
 #ifndef	__DAVINCI_GPIO_H
 #define	__DAVINCI_GPIO_H
 
-#include <linux/io.h>
-#include <linux/spinlock.h>
-
 #include <asm-generic/gpio.h>
 
-#include <mach/irqs.h>
-#include <mach/common.h>
-
-#define DAVINCI_GPIO_BASE 0x01C67000
-
-enum davinci_gpio_type {
-	GPIO_TYPE_DAVINCI = 0,
-	GPIO_TYPE_TNETV107X,
-};
-
-/*
- * basic gpio routines
- *
- * board-specific init should be done by arch/.../.../board-XXX.c (maybe
- * initializing banks together) rather than boot loaders; kexec() won't
- * go through boot loaders.
- *
- * the gpio clock will be turned on when gpios are used, and you may also
- * need to pay attention to PINMUX registers to be sure those pins are
- * used as gpios, not with other peripherals.
- *
- * On-chip GPIOs are numbered 0..(DAVINCI_N_GPIO-1).  For documentation,
- * and maybe for later updates, code may write GPIO(N).  These may be
- * all 1.8V signals, all 3.3V ones, or a mix of the two.  A given chip
- * may not support all the GPIOs in that range.
- *
- * GPIOs can also be on external chips, numbered after the ones built-in
- * to the DaVinci chip.  For now, they won't be usable as IRQ sources.
- */
-#define	GPIO(X)		(X)		/* 0 <= X <= (DAVINCI_N_GPIO - 1) */
-
-/* Convert GPIO signal to GPIO pin number */
-#define GPIO_TO_PIN(bank, gpio)	(16 * (bank) + (gpio))
-
-struct davinci_gpio_controller {
-	struct gpio_chip	chip;
-	int			irq_base;
-	spinlock_t		lock;
-	void __iomem		*regs;
-	void __iomem		*set_data;
-	void __iomem		*clr_data;
-	void __iomem		*in_data;
-};
-
-/* The __gpio_to_controller() and __gpio_mask() functions inline to constants
- * with constant parameters; or in outlined code they execute at runtime.
- *
- * You'd access the controller directly when reading or writing more than
- * one gpio value at a time, and to support wired logic where the value
- * being driven by the cpu need not match the value read back.
- *
- * These are NOT part of the cross-platform GPIO interface
- */
-static inline struct davinci_gpio_controller *
-__gpio_to_controller(unsigned gpio)
-{
-	struct davinci_gpio_controller *ctlrs = davinci_soc_info.gpio_ctlrs;
-	int index = gpio / 32;
-
-	if (!ctlrs || index >= davinci_soc_info.gpio_ctlrs_num)
-		return NULL;
-
-	return ctlrs + index;
-}
-
-static inline u32 __gpio_mask(unsigned gpio)
-{
-	return 1 << (gpio % 32);
-}
+/* The inline versions use the static inlines in the driver header */
+#include "gpio-davinci.h"
 
 /*
  * The get/set/clear functions will inline when called with constant
@@ -147,11 +77,6 @@ static inline int gpio_cansleep(unsigned gpio)
 		return __gpio_cansleep(gpio);
 }
 
-static inline int gpio_to_irq(unsigned gpio)
-{
-	return __gpio_to_irq(gpio);
-}
-
 static inline int irq_to_gpio(unsigned irq)
 {
 	/* don't support the reverse mapping */
diff --git a/arch/arm/mach-davinci/tnetv107x.c b/arch/arm/mach-davinci/tnetv107x.c
index 1b28fdd892a6..409bb869c7c7 100644
--- a/arch/arm/mach-davinci/tnetv107x.c
+++ b/arch/arm/mach-davinci/tnetv107x.c
@@ -12,6 +12,7 @@
  * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  */
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/clk.h>
@@ -27,9 +28,9 @@
 #include <mach/psc.h>
 #include <mach/cp_intc.h>
 #include <mach/irqs.h>
-#include <mach/gpio.h>
 #include <mach/hardware.h>
 #include <mach/tnetv107x.h>
+#include <mach/gpio-davinci.h>
 
 #include "clock.h"
 #include "mux.h"
diff --git a/arch/arm/mach-ebsa110/include/mach/io.h b/arch/arm/mach-ebsa110/include/mach/io.h
index f68daa632af0..44679db672fb 100644
--- a/arch/arm/mach-ebsa110/include/mach/io.h
+++ b/arch/arm/mach-ebsa110/include/mach/io.h
@@ -13,8 +13,6 @@
 #ifndef __ASM_ARM_ARCH_IO_H
 #define __ASM_ARM_ARCH_IO_H
 
-#define IO_SPACE_LIMIT 0xffff
-
 u8 __inb8(unsigned int port);
 void __outb8(u8  val, unsigned int port);
 
diff --git a/arch/arm/mach-ep93xx/core.c b/arch/arm/mach-ep93xx/core.c
index c60f081e930b..94c78bc66275 100644
--- a/arch/arm/mach-ep93xx/core.c
+++ b/arch/arm/mach-ep93xx/core.c
@@ -38,6 +38,7 @@
 #include <mach/fb.h>
 #include <mach/ep93xx_keypad.h>
 #include <mach/ep93xx_spi.h>
+#include <mach/gpio-ep93xx.h>
 
 #include <asm/mach/map.h>
 #include <asm/mach/time.h>
diff --git a/arch/arm/mach-ep93xx/edb93xx.c b/arch/arm/mach-ep93xx/edb93xx.c
index 257175edc575..c63a5ec1a8e3 100644
--- a/arch/arm/mach-ep93xx/edb93xx.c
+++ b/arch/arm/mach-ep93xx/edb93xx.c
@@ -37,6 +37,7 @@
 #include <mach/hardware.h>
 #include <mach/fb.h>
 #include <mach/ep93xx_spi.h>
+#include <mach/gpio-ep93xx.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
diff --git a/arch/arm/mach-ep93xx/include/mach/gpio.h b/arch/arm/mach-ep93xx/include/mach/gpio-ep93xx.h
index c57152c231f1..8aff2ea35877 100644
--- a/arch/arm/mach-ep93xx/include/mach/gpio.h
+++ b/arch/arm/mach-ep93xx/include/mach/gpio-ep93xx.h
@@ -1,9 +1,7 @@
-/*
- * arch/arm/mach-ep93xx/include/mach/gpio.h
- */
+/* Include file for the EP93XX GPIO controller machine specifics */
 
-#ifndef __ASM_ARCH_GPIO_H
-#define __ASM_ARCH_GPIO_H
+#ifndef __GPIO_EP93XX_H
+#define __GPIO_EP93XX_H
 
 /* GPIO port A.  */
 #define EP93XX_GPIO_LINE_A(x)		((x) + 0)
@@ -99,22 +97,4 @@
 /* maximum value for irq capable line identifiers */
 #define EP93XX_GPIO_LINE_MAX_IRQ	EP93XX_GPIO_LINE_F(7)
 
-/* new generic GPIO API - see Documentation/gpio.txt */
-
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value	__gpio_get_value
-#define gpio_set_value	__gpio_set_value
-#define gpio_cansleep	__gpio_cansleep
-
-/*
- * Map GPIO A0..A7  (0..7)  to irq 64..71,
- *          B0..B7  (7..15) to irq 72..79, and
- *          F0..F7 (16..24) to irq 80..87.
- */
-#define gpio_to_irq(gpio)	\
-	(((gpio) <= EP93XX_GPIO_LINE_MAX_IRQ) ? (64 + (gpio)) : -EINVAL)
-
-#define irq_to_gpio(irq)	((irq) - gpio_to_irq(0))
-
-#endif
+#endif /* __GPIO_EP93XX_H */
diff --git a/arch/arm/mach-ep93xx/simone.c b/arch/arm/mach-ep93xx/simone.c
index 238bc603da86..d6f286b4db9c 100644
--- a/arch/arm/mach-ep93xx/simone.c
+++ b/arch/arm/mach-ep93xx/simone.c
@@ -18,12 +18,12 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
-#include <linux/gpio.h>
 #include <linux/i2c.h>
 #include <linux/i2c-gpio.h>
 
 #include <mach/hardware.h>
 #include <mach/fb.h>
+#include <mach/gpio-ep93xx.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
diff --git a/arch/arm/mach-ep93xx/snappercl15.c b/arch/arm/mach-ep93xx/snappercl15.c
index 3bdf3a2e5ad0..2b4d4b0201df 100644
--- a/arch/arm/mach-ep93xx/snappercl15.c
+++ b/arch/arm/mach-ep93xx/snappercl15.c
@@ -20,7 +20,6 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/io.h>
-#include <linux/gpio.h>
 #include <linux/i2c.h>
 #include <linux/i2c-gpio.h>
 #include <linux/fb.h>
@@ -30,6 +29,7 @@
 
 #include <mach/hardware.h>
 #include <mach/fb.h>
+#include <mach/gpio-ep93xx.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
diff --git a/arch/arm/mach-exynos4/include/mach/gpio.h b/arch/arm/mach-exynos4/include/mach/gpio.h
index be9266b10fdb..80523ca9bb49 100644
--- a/arch/arm/mach-exynos4/include/mach/gpio.h
+++ b/arch/arm/mach-exynos4/include/mach/gpio.h
@@ -13,11 +13,6 @@
 #ifndef __ASM_ARCH_GPIO_H
 #define __ASM_ARCH_GPIO_H __FILE__
 
-#define gpio_get_value	__gpio_get_value
-#define gpio_set_value	__gpio_set_value
-#define gpio_cansleep	__gpio_cansleep
-#define gpio_to_irq	__gpio_to_irq
-
 /* Practically, GPIO banks up to GPZ are the configurable gpio banks */
 
 /* GPIO bank sizes */
@@ -151,6 +146,4 @@ enum s5p_gpio_number {
 #define ARCH_NR_GPIOS		(EXYNOS4_GPZ(EXYNOS4_GPIO_Z_NR) +	\
 				 CONFIG_SAMSUNG_GPIO_EXTRA + 1)
 
-#include <asm-generic/gpio.h>
-
 #endif /* __ASM_ARCH_GPIO_H */
diff --git a/arch/arm/mach-footbridge/include/mach/io.h b/arch/arm/mach-footbridge/include/mach/io.h
index 32e4cc397c28..15a70396c27d 100644
--- a/arch/arm/mach-footbridge/include/mach/io.h
+++ b/arch/arm/mach-footbridge/include/mach/io.h
@@ -23,8 +23,6 @@
 #define PCIO_SIZE       0x00100000
 #define PCIO_BASE       MMU_IO(0xff000000, 0x7c000000)
 
-#define IO_SPACE_LIMIT 0xffff
-
 /*
  * Translation of various region addresses to virtual addresses
  */
diff --git a/arch/arm/mach-gemini/include/mach/gpio.h b/arch/arm/mach-gemini/include/mach/gpio.h
index 3bc2c70f2989..40a0527bada7 100644
--- a/arch/arm/mach-gemini/include/mach/gpio.h
+++ b/arch/arm/mach-gemini/include/mach/gpio.h
@@ -13,11 +13,6 @@
 #define __MACH_GPIO_H__
 
 #include <mach/irqs.h>
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value	__gpio_get_value
-#define gpio_set_value	__gpio_set_value
-#define gpio_cansleep	__gpio_cansleep
 
 #define gpio_to_irq(x)	((x) + GPIO_IRQ_BASE)
 #define irq_to_gpio(x)	((x) - GPIO_IRQ_BASE)
diff --git a/arch/arm/mach-highbank/Makefile b/arch/arm/mach-highbank/Makefile
new file mode 100644
index 000000000000..986958a5a720
--- /dev/null
+++ b/arch/arm/mach-highbank/Makefile
@@ -0,0 +1,6 @@
+obj-y					:= clock.o highbank.o system.o
+obj-$(CONFIG_DEBUG_HIGHBANK_UART)	+= lluart.o
+obj-$(CONFIG_SMP)			+= platsmp.o
+obj-$(CONFIG_LOCAL_TIMERS)		+= localtimer.o
+obj-$(CONFIG_HOTPLUG_CPU)		+= hotplug.o
+obj-$(CONFIG_PM_SLEEP)			+= pm.o
diff --git a/arch/arm/mach-highbank/Makefile.boot b/arch/arm/mach-highbank/Makefile.boot
new file mode 100644
index 000000000000..dae9661a7689
--- /dev/null
+++ b/arch/arm/mach-highbank/Makefile.boot
@@ -0,0 +1 @@
+zreladdr-y	:= 0x00008000
diff --git a/arch/arm/mach-highbank/clock.c b/arch/arm/mach-highbank/clock.c
new file mode 100644
index 000000000000..c25a2ae4fde1
--- /dev/null
+++ b/arch/arm/mach-highbank/clock.c
@@ -0,0 +1,62 @@
+/*
+ * Copyright 2011 Calxeda, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/clk.h>
+#include <linux/clkdev.h>
+
+struct clk {
+	unsigned long rate;
+};
+
+int clk_enable(struct clk *clk)
+{
+	return 0;
+}
+
+void clk_disable(struct clk *clk)
+{}
+
+unsigned long clk_get_rate(struct clk *clk)
+{
+	return clk->rate;
+}
+
+long clk_round_rate(struct clk *clk, unsigned long rate)
+{
+	return clk->rate;
+}
+
+int clk_set_rate(struct clk *clk, unsigned long rate)
+{
+	return 0;
+}
+
+static struct clk eclk = { .rate = 200000000 };
+static struct clk pclk = { .rate = 150000000 };
+
+static struct clk_lookup lookups[] = {
+	{ .clk = &pclk, .con_id = "apb_pclk", },
+	{ .clk = &pclk, .dev_id = "sp804", },
+	{ .clk = &eclk, .dev_id = "ffe0e000.sdhci", },
+	{ .clk = &pclk, .dev_id = "fff36000.serial", },
+};
+
+void __init highbank_clocks_init(void)
+{
+	clkdev_add_table(lookups, ARRAY_SIZE(lookups));
+}
diff --git a/arch/arm/mach-highbank/core.h b/arch/arm/mach-highbank/core.h
new file mode 100644
index 000000000000..7e33fc94cd1e
--- /dev/null
+++ b/arch/arm/mach-highbank/core.h
@@ -0,0 +1,9 @@
+extern void highbank_set_cpu_jump(int cpu, void *jump_addr);
+extern void highbank_clocks_init(void);
+extern void __iomem *scu_base_addr;
+#ifdef CONFIG_DEBUG_HIGHBANK_UART
+extern void highbank_lluart_map_io(void);
+#else
+static inline void highbank_lluart_map_io(void) {}
+#endif
+
diff --git a/arch/arm/mach-highbank/highbank.c b/arch/arm/mach-highbank/highbank.c
new file mode 100644
index 000000000000..b82dcf08e747
--- /dev/null
+++ b/arch/arm/mach-highbank/highbank.c
@@ -0,0 +1,145 @@
+/*
+ * Copyright 2010-2011 Calxeda, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <linux/clk.h>
+#include <linux/clkdev.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/of_address.h>
+
+#include <asm/cacheflush.h>
+#include <asm/unified.h>
+#include <asm/smp_scu.h>
+#include <asm/hardware/arm_timer.h>
+#include <asm/hardware/timer-sp.h>
+#include <asm/hardware/gic.h>
+#include <asm/hardware/cache-l2x0.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/time.h>
+#include <mach/irqs.h>
+
+#include "core.h"
+#include "sysregs.h"
+
+void __iomem *sregs_base;
+
+#define HB_SCU_VIRT_BASE	0xfee00000
+void __iomem *scu_base_addr = ((void __iomem *)(HB_SCU_VIRT_BASE));
+
+static struct map_desc scu_io_desc __initdata = {
+	.virtual	= HB_SCU_VIRT_BASE,
+	.pfn		= 0, /* run-time */
+	.length		= SZ_4K,
+	.type		= MT_DEVICE,
+};
+
+static void __init highbank_scu_map_io(void)
+{
+	unsigned long base;
+
+	/* Get SCU base */
+	asm("mrc p15, 4, %0, c15, c0, 0" : "=r" (base));
+
+	scu_io_desc.pfn = __phys_to_pfn(base);
+	iotable_init(&scu_io_desc, 1);
+}
+
+static void __init highbank_map_io(void)
+{
+	highbank_scu_map_io();
+	highbank_lluart_map_io();
+}
+
+#define HB_JUMP_TABLE_PHYS(cpu)		(0x40 + (0x10 * (cpu)))
+#define HB_JUMP_TABLE_VIRT(cpu)		phys_to_virt(HB_JUMP_TABLE_PHYS(cpu))
+
+void highbank_set_cpu_jump(int cpu, void *jump_addr)
+{
+	writel(BSYM(virt_to_phys(jump_addr)), HB_JUMP_TABLE_VIRT(cpu));
+	__cpuc_flush_dcache_area(HB_JUMP_TABLE_VIRT(cpu), 16);
+	outer_clean_range(HB_JUMP_TABLE_PHYS(cpu),
+			  HB_JUMP_TABLE_PHYS(cpu) + 15);
+}
+
+const static struct of_device_id irq_match[] = {
+	{ .compatible = "arm,cortex-a9-gic", .data = gic_of_init, },
+	{}
+};
+
+static void __init highbank_init_irq(void)
+{
+	of_irq_init(irq_match);
+	l2x0_of_init(0, ~0UL);
+}
+
+static void __init highbank_timer_init(void)
+{
+	int irq;
+	struct device_node *np;
+	void __iomem *timer_base;
+
+	/* Map system registers */
+	np = of_find_compatible_node(NULL, NULL, "calxeda,hb-sregs");
+	sregs_base = of_iomap(np, 0);
+	WARN_ON(!sregs_base);
+
+	np = of_find_compatible_node(NULL, NULL, "arm,sp804");
+	timer_base = of_iomap(np, 0);
+	WARN_ON(!timer_base);
+	irq = irq_of_parse_and_map(np, 0);
+
+	highbank_clocks_init();
+
+	sp804_clocksource_init(timer_base + 0x20, "timer1");
+	sp804_clockevents_init(timer_base, irq, "timer0");
+}
+
+static struct sys_timer highbank_timer = {
+	.init = highbank_timer_init,
+};
+
+static void highbank_power_off(void)
+{
+	hignbank_set_pwr_shutdown();
+	scu_power_mode(scu_base_addr, SCU_PM_POWEROFF);
+
+	while (1)
+		cpu_do_idle();
+}
+
+static void __init highbank_init(void)
+{
+	pm_power_off = highbank_power_off;
+
+	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
+}
+
+static const char *highbank_match[] __initconst = {
+	"calxeda,highbank",
+	NULL,
+};
+
+DT_MACHINE_START(HIGHBANK, "Highbank")
+	.map_io		= highbank_map_io,
+	.init_irq	= highbank_init_irq,
+	.timer		= &highbank_timer,
+	.init_machine	= highbank_init,
+	.dt_compat	= highbank_match,
+MACHINE_END
diff --git a/arch/arm/mach-highbank/hotplug.c b/arch/arm/mach-highbank/hotplug.c
new file mode 100644
index 000000000000..977cebbea580
--- /dev/null
+++ b/arch/arm/mach-highbank/hotplug.c
@@ -0,0 +1,56 @@
+/*
+ * Copyright 2011 Calxeda, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/smp.h>
+
+#include <asm/smp_scu.h>
+#include <asm/cacheflush.h>
+
+#include "core.h"
+
+extern void secondary_startup(void);
+
+int platform_cpu_kill(unsigned int cpu)
+{
+	return 1;
+}
+
+/*
+ * platform-specific code to shutdown a CPU
+ *
+ */
+void platform_cpu_die(unsigned int cpu)
+{
+	flush_cache_all();
+
+	highbank_set_cpu_jump(cpu, secondary_startup);
+	scu_power_mode(scu_base_addr, SCU_PM_POWEROFF);
+
+	cpu_do_idle();
+
+	/* We should never return from idle */
+	panic("highbank: cpu %d unexpectedly exit from shutdown\n", cpu);
+}
+
+int platform_cpu_disable(unsigned int cpu)
+{
+	/*
+	 * CPU0 should not be shut down via hotplug.  cpu_idle can WFI
+	 * or a proper shutdown or hibernate should be used.
+	 */
+	return cpu == 0 ? -EPERM : 0;
+}
diff --git a/arch/arm/mach-highbank/include/mach/debug-macro.S b/arch/arm/mach-highbank/include/mach/debug-macro.S
new file mode 100644
index 000000000000..cb57fe5bcd04
--- /dev/null
+++ b/arch/arm/mach-highbank/include/mach/debug-macro.S
@@ -0,0 +1,19 @@
+/*
+ * Debugging macro include header
+ *
+ *  Copyright (C) 1994-1999 Russell King
+ *  Moved from linux/arch/arm/kernel/debug.S by Ben Dooks
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+		.macro	addruart,rp,rv,tmp
+		movw	\rv, #0x6000
+		movt	\rv, #0xfee3
+		movw	\rp, #0x6000
+		movt	\rp, #0xfff3
+		.endm
+
+#include <asm/hardware/debug-pl01x.S>
diff --git a/arch/arm/mach-highbank/include/mach/entry-macro.S b/arch/arm/mach-highbank/include/mach/entry-macro.S
new file mode 100644
index 000000000000..73c11297509e
--- /dev/null
+++ b/arch/arm/mach-highbank/include/mach/entry-macro.S
@@ -0,0 +1,7 @@
+#include <asm/hardware/entry-macro-gic.S>
+
+	.macro	disable_fiq
+	.endm
+
+	.macro	arch_ret_to_user, tmp1, tmp2
+	.endm
diff --git a/arch/arm/mach-highbank/include/mach/gpio.h b/arch/arm/mach-highbank/include/mach/gpio.h
new file mode 100644
index 000000000000..40a8c178f10d
--- /dev/null
+++ b/arch/arm/mach-highbank/include/mach/gpio.h
@@ -0,0 +1 @@
+/* empty */
diff --git a/arch/arm/mach-highbank/include/mach/io.h b/arch/arm/mach-highbank/include/mach/io.h
new file mode 100644
index 000000000000..70cfa3ba7697
--- /dev/null
+++ b/arch/arm/mach-highbank/include/mach/io.h
@@ -0,0 +1,7 @@
+#ifndef __MACH_IO_H
+#define __MACH_IO_H
+
+#define __io(a)		({ (void)(a); __typesafe_io(0); })
+#define __mem_pci(a)	(a)
+
+#endif
diff --git a/arch/arm/mach-highbank/include/mach/irqs.h b/arch/arm/mach-highbank/include/mach/irqs.h
new file mode 100644
index 000000000000..9746aab14e9a
--- /dev/null
+++ b/arch/arm/mach-highbank/include/mach/irqs.h
@@ -0,0 +1,6 @@
+#ifndef __MACH_IRQS_H
+#define __MACH_IRQS_H
+
+#define NR_IRQS			192
+
+#endif
diff --git a/arch/arm/mach-highbank/include/mach/memory.h b/arch/arm/mach-highbank/include/mach/memory.h
new file mode 100644
index 000000000000..40a8c178f10d
--- /dev/null
+++ b/arch/arm/mach-highbank/include/mach/memory.h
@@ -0,0 +1 @@
+/* empty */
diff --git a/arch/arm/mach-highbank/include/mach/system.h b/arch/arm/mach-highbank/include/mach/system.h
new file mode 100644
index 000000000000..7e8192296cae
--- /dev/null
+++ b/arch/arm/mach-highbank/include/mach/system.h
@@ -0,0 +1,26 @@
+/*
+ * Copyright 2010-2011 Calxeda, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#ifndef __MACH_SYSTEM_H
+#define __MACH_SYSTEM_H
+
+static inline void arch_idle(void)
+{
+	cpu_do_idle();
+}
+
+extern void arch_reset(char mode, const char *cmd);
+
+#endif
diff --git a/arch/arm/mach-highbank/include/mach/timex.h b/arch/arm/mach-highbank/include/mach/timex.h
new file mode 100644
index 000000000000..88dac7a55a97
--- /dev/null
+++ b/arch/arm/mach-highbank/include/mach/timex.h
@@ -0,0 +1,6 @@
+#ifndef __MACH_TIMEX_H
+#define __MACH_TIMEX_H
+
+#define CLOCK_TICK_RATE		1000000
+
+#endif
diff --git a/arch/arm/mach-highbank/include/mach/uncompress.h b/arch/arm/mach-highbank/include/mach/uncompress.h
new file mode 100644
index 000000000000..bbe20e696325
--- /dev/null
+++ b/arch/arm/mach-highbank/include/mach/uncompress.h
@@ -0,0 +1,9 @@
+#ifndef __MACH_UNCOMPRESS_H
+#define __MACH_UNCOMPRESS_H
+
+#define putc(c)
+#define flush()
+#define arch_decomp_setup()
+#define arch_decomp_wdog()
+
+#endif
diff --git a/arch/arm/mach-highbank/include/mach/vmalloc.h b/arch/arm/mach-highbank/include/mach/vmalloc.h
new file mode 100644
index 000000000000..1969e954277a
--- /dev/null
+++ b/arch/arm/mach-highbank/include/mach/vmalloc.h
@@ -0,0 +1 @@
+#define VMALLOC_END		0xFEE00000UL
diff --git a/arch/arm/mach-highbank/lluart.c b/arch/arm/mach-highbank/lluart.c
new file mode 100644
index 000000000000..371575019f33
--- /dev/null
+++ b/arch/arm/mach-highbank/lluart.c
@@ -0,0 +1,34 @@
+/*
+ * Copyright 2011 Calxeda, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <linux/init.h>
+#include <asm/page.h>
+#include <asm/sizes.h>
+#include <asm/mach/map.h>
+
+#define HB_DEBUG_LL_PHYS_BASE	0xfff36000
+#define HB_DEBUG_LL_VIRT_BASE	0xfee36000
+
+static struct map_desc lluart_io_desc __initdata = {
+	.virtual	= HB_DEBUG_LL_VIRT_BASE,
+	.pfn		= __phys_to_pfn(HB_DEBUG_LL_PHYS_BASE),
+	.length		= SZ_4K,
+	.type		= MT_DEVICE,
+};
+
+void __init highbank_lluart_map_io(void)
+{
+	iotable_init(&lluart_io_desc, 1);
+}
diff --git a/arch/arm/mach-highbank/localtimer.c b/arch/arm/mach-highbank/localtimer.c
new file mode 100644
index 000000000000..5a00e7945fdf
--- /dev/null
+++ b/arch/arm/mach-highbank/localtimer.c
@@ -0,0 +1,40 @@
+/*
+ * Copyright 2010-2011 Calxeda, Inc.
+ * Based on localtimer.c, Copyright (C) 2002 ARM Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <linux/init.h>
+#include <linux/clockchips.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+
+#include <asm/smp_twd.h>
+
+/*
+ * Setup the local clock events for a CPU.
+ */
+int __cpuinit local_timer_setup(struct clock_event_device *evt)
+{
+	struct device_node *np;
+
+	np = of_find_compatible_node(NULL, NULL, "arm,smp-twd");
+	if (!twd_base) {
+		twd_base = of_iomap(np, 0);
+		WARN_ON(!twd_base);
+	}
+	evt->irq = irq_of_parse_and_map(np, 0);
+	twd_timer_setup(evt);
+	return 0;
+}
diff --git a/arch/arm/mach-highbank/platsmp.c b/arch/arm/mach-highbank/platsmp.c
new file mode 100644
index 000000000000..d01364c72b45
--- /dev/null
+++ b/arch/arm/mach-highbank/platsmp.c
@@ -0,0 +1,78 @@
+/*
+ * Copyright 2010-2011 Calxeda, Inc.
+ * Based on platsmp.c, Copyright (C) 2002 ARM Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <linux/init.h>
+#include <linux/smp.h>
+#include <linux/io.h>
+
+#include <asm/smp_scu.h>
+#include <asm/hardware/gic.h>
+
+#include "core.h"
+
+extern void secondary_startup(void);
+
+void __cpuinit platform_secondary_init(unsigned int cpu)
+{
+	gic_secondary_init(0);
+}
+
+int __cpuinit boot_secondary(unsigned int cpu, struct task_struct *idle)
+{
+	gic_raise_softirq(cpumask_of(cpu), 0);
+	return 0;
+}
+
+/*
+ * Initialise the CPU possible map early - this describes the CPUs
+ * which may be present or become present in the system.
+ */
+void __init smp_init_cpus(void)
+{
+	unsigned int i, ncores;
+
+	ncores = scu_get_core_count(scu_base_addr);
+
+	/* sanity check */
+	if (ncores > NR_CPUS) {
+		printk(KERN_WARNING
+		       "highbank: no. of cores (%d) greater than configured "
+		       "maximum of %d - clipping\n",
+		       ncores, NR_CPUS);
+		ncores = NR_CPUS;
+	}
+
+	for (i = 0; i < ncores; i++)
+		set_cpu_possible(i, true);
+
+	set_smp_cross_call(gic_raise_softirq);
+}
+
+void __init platform_smp_prepare_cpus(unsigned int max_cpus)
+{
+	int i;
+
+	scu_enable(scu_base_addr);
+
+	/*
+	 * Write the address of secondary startup into the jump table
+	 * The cores are in wfi and wait until they receive a soft interrupt
+	 * and a non-zero value to jump to. Then the secondary CPU branches
+	 * to this address.
+	 */
+	for (i = 1; i < max_cpus; i++)
+		highbank_set_cpu_jump(i, secondary_startup);
+}
diff --git a/arch/arm/mach-highbank/pm.c b/arch/arm/mach-highbank/pm.c
new file mode 100644
index 000000000000..33b3beb89982
--- /dev/null
+++ b/arch/arm/mach-highbank/pm.c
@@ -0,0 +1,55 @@
+/*
+ * Copyright 2011 Calxeda, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/suspend.h>
+
+#include <asm/proc-fns.h>
+#include <asm/smp_scu.h>
+#include <asm/suspend.h>
+
+#include "core.h"
+#include "sysregs.h"
+
+static int highbank_suspend_finish(unsigned long val)
+{
+	cpu_do_idle();
+	return 0;
+}
+
+static int highbank_pm_enter(suspend_state_t state)
+{
+	hignbank_set_pwr_suspend();
+	highbank_set_cpu_jump(0, cpu_resume);
+
+	scu_power_mode(scu_base_addr, SCU_PM_POWEROFF);
+	cpu_suspend(0, highbank_suspend_finish);
+
+	return 0;
+}
+
+static const struct platform_suspend_ops highbank_pm_ops = {
+	.enter = highbank_pm_enter,
+	.valid = suspend_valid_only_mem,
+};
+
+static int __init highbank_pm_init(void)
+{
+	suspend_set_ops(&highbank_pm_ops);
+	return 0;
+}
+module_init(highbank_pm_init);
diff --git a/arch/arm/mach-highbank/sysregs.h b/arch/arm/mach-highbank/sysregs.h
new file mode 100644
index 000000000000..0e913389f445
--- /dev/null
+++ b/arch/arm/mach-highbank/sysregs.h
@@ -0,0 +1,52 @@
+/*
+ * Copyright 2011 Calxeda, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#ifndef _MACH_HIGHBANK__SYSREGS_H_
+#define _MACH_HIGHBANK__SYSREGS_H_
+
+#include <linux/io.h>
+
+extern void __iomem *sregs_base;
+
+#define HB_SREG_A9_PWR_REQ		0xf00
+#define HB_SREG_A9_BOOT_STAT		0xf04
+#define HB_SREG_A9_BOOT_DATA		0xf08
+
+#define HB_PWR_SUSPEND			0
+#define HB_PWR_SOFT_RESET		1
+#define HB_PWR_HARD_RESET		2
+#define HB_PWR_SHUTDOWN			3
+
+static inline void hignbank_set_pwr_suspend(void)
+{
+	writel(HB_PWR_SUSPEND, sregs_base + HB_SREG_A9_PWR_REQ);
+}
+
+static inline void hignbank_set_pwr_shutdown(void)
+{
+	writel(HB_PWR_SHUTDOWN, sregs_base + HB_SREG_A9_PWR_REQ);
+}
+
+static inline void hignbank_set_pwr_soft_reset(void)
+{
+	writel(HB_PWR_SOFT_RESET, sregs_base + HB_SREG_A9_PWR_REQ);
+}
+
+static inline void hignbank_set_pwr_hard_reset(void)
+{
+	writel(HB_PWR_HARD_RESET, sregs_base + HB_SREG_A9_PWR_REQ);
+}
+
+#endif
diff --git a/arch/arm/mach-highbank/system.c b/arch/arm/mach-highbank/system.c
new file mode 100644
index 000000000000..53f0c4c5ef1c
--- /dev/null
+++ b/arch/arm/mach-highbank/system.c
@@ -0,0 +1,33 @@
+/*
+ * Copyright 2011 Calxeda, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <linux/io.h>
+#include <asm/smp_scu.h>
+#include <asm/proc-fns.h>
+
+#include "core.h"
+#include "sysregs.h"
+
+void arch_reset(char mode, const char *cmd)
+{
+	if (mode == 'h')
+		hignbank_set_pwr_hard_reset();
+	else
+		hignbank_set_pwr_soft_reset();
+
+	scu_power_mode(scu_base_addr, SCU_PM_POWEROFF);
+	cpu_do_idle();
+}
+
diff --git a/arch/arm/mach-imx/iomux-imx31.c b/arch/arm/mach-imx/iomux-imx31.c
index cf8f8099ebd7..82bd4403b450 100644
--- a/arch/arm/mach-imx/iomux-imx31.c
+++ b/arch/arm/mach-imx/iomux-imx31.c
@@ -17,13 +17,12 @@
  * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
  * MA 02110-1301, USA.
  */
-
+#include <linux/gpio.h>
 #include <linux/module.h>
 #include <linux/spinlock.h>
 #include <linux/io.h>
 #include <linux/kernel.h>
 #include <mach/hardware.h>
-#include <mach/gpio.h>
 #include <mach/iomux-mx3.h>
 
 /*
diff --git a/arch/arm/mach-imx/mach-mx27ads.c b/arch/arm/mach-imx/mach-mx27ads.c
index e75f39147845..74dd5731eb61 100644
--- a/arch/arm/mach-imx/mach-mx27ads.c
+++ b/arch/arm/mach-imx/mach-mx27ads.c
@@ -13,7 +13,7 @@
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  */
-
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/map.h>
@@ -27,7 +27,6 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/time.h>
 #include <asm/mach/map.h>
-#include <mach/gpio.h>
 #include <mach/iomux-mx27.h>
 
 #include "devices-imx27.h"
diff --git a/arch/arm/mach-integrator/include/mach/io.h b/arch/arm/mach-integrator/include/mach/io.h
index f21bb5493dd9..37beed3fa3ed 100644
--- a/arch/arm/mach-integrator/include/mach/io.h
+++ b/arch/arm/mach-integrator/include/mach/io.h
@@ -20,8 +20,6 @@
 #ifndef __ASM_ARM_ARCH_IO_H
 #define __ASM_ARM_ARCH_IO_H
 
-#define IO_SPACE_LIMIT 0xffff
-
 /*
  * WARNING: this has to mirror definitions in platform.h
  */
diff --git a/arch/arm/mach-ixp2000/core.c b/arch/arm/mach-ixp2000/core.c
index 4068166c8993..59a512672bb9 100644
--- a/arch/arm/mach-ixp2000/core.c
+++ b/arch/arm/mach-ixp2000/core.c
@@ -13,7 +13,7 @@
  * License version 2. This program is licensed "as is" without any 
  * warranty of any kind, whether express or implied.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/spinlock.h>
@@ -39,7 +39,7 @@
 #include <asm/mach/time.h>
 #include <asm/mach/irq.h>
 
-#include <mach/gpio.h>
+#include <mach/gpio-ixp2000.h>
 
 static DEFINE_SPINLOCK(ixp2000_slowport_lock);
 static unsigned long ixp2000_slowport_irq_flags;
diff --git a/arch/arm/mach-ixp2000/include/mach/gpio.h b/arch/arm/mach-ixp2000/include/mach/gpio-ixp2000.h
index 4a88d2c33dac..af836c76c3f1 100644
--- a/arch/arm/mach-ixp2000/include/mach/gpio.h
+++ b/arch/arm/mach-ixp2000/include/mach/gpio-ixp2000.h
@@ -3,7 +3,7 @@
  *
  * Copyright (C) 2002 Intel Corporation.
  *
- * This program is free software, you can redistribute it and/or modify 
+ * This program is free software, you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
@@ -11,7 +11,7 @@
 /*
  * IXP2000 GPIO in/out, edge/level detection for IRQs:
  * IRQs are generated on Falling-edge, Rising-Edge, Level-low, Level-High
- * or both Falling-edge and Rising-edge.  
+ * or both Falling-edge and Rising-edge.
  * This must be called *before* the corresponding IRQ is registerd.
  * Use this instead of directly setting the GPIO registers.
  * GPIOs may also be used as GPIOs (e.g. for emulating i2c/smb)
diff --git a/arch/arm/mach-ixp2000/ixdp2x00.c b/arch/arm/mach-ixp2000/ixdp2x00.c
index 235638f800e5..634b6c852f68 100644
--- a/arch/arm/mach-ixp2000/ixdp2x00.c
+++ b/arch/arm/mach-ixp2000/ixdp2x00.c
@@ -14,6 +14,7 @@
  *  Free Software Foundation;  either version 2 of the  License, or (at your
  *  option) any later version.
  */
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/mm.h>
@@ -40,8 +41,7 @@
 #include <asm/mach/flash.h>
 #include <asm/mach/arch.h>
 
-#include <mach/gpio.h>
-
+#include <mach/gpio-ixp2000.h>
 
 /*************************************************************************
  * IXDP2x00 IRQ Initialization
diff --git a/arch/arm/mach-ixp4xx/dsmg600-setup.c b/arch/arm/mach-ixp4xx/dsmg600-setup.c
index 71607a7ecc7e..8837fbca27ce 100644
--- a/arch/arm/mach-ixp4xx/dsmg600-setup.c
+++ b/arch/arm/mach-ixp4xx/dsmg600-setup.c
@@ -16,7 +16,7 @@
  * Author: Rod Whitby <rod@whitby.id.au>
  * Maintainers: http://www.nslu2-linux.org/
  */
-
+#include <linux/gpio.h>
 #include <linux/irq.h>
 #include <linux/jiffies.h>
 #include <linux/timer.h>
@@ -31,7 +31,6 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/flash.h>
 #include <asm/mach/time.h>
-#include <asm/gpio.h>
 
 #define DSMG600_SDA_PIN		5
 #define DSMG600_SCL_PIN		4
diff --git a/arch/arm/mach-ixp4xx/fsg-setup.c b/arch/arm/mach-ixp4xx/fsg-setup.c
index a9540cd90375..2887c3578c17 100644
--- a/arch/arm/mach-ixp4xx/fsg-setup.c
+++ b/arch/arm/mach-ixp4xx/fsg-setup.c
@@ -14,7 +14,7 @@
  * Maintainers: http://www.nslu2-linux.org/
  *
  */
-
+#include <linux/gpio.h>
 #include <linux/if_ether.h>
 #include <linux/irq.h>
 #include <linux/serial.h>
@@ -27,7 +27,6 @@
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/flash.h>
-#include <asm/gpio.h>
 
 #define FSG_SDA_PIN		12
 #define FSG_SCL_PIN		13
diff --git a/arch/arm/mach-ixp4xx/include/mach/gpio.h b/arch/arm/mach-ixp4xx/include/mach/gpio.h
index a5f87ded2f28..83d6b4ed60bb 100644
--- a/arch/arm/mach-ixp4xx/include/mach/gpio.h
+++ b/arch/arm/mach-ixp4xx/include/mach/gpio.h
@@ -28,6 +28,8 @@
 #include <linux/kernel.h>
 #include <mach/hardware.h>
 
+#define __ARM_GPIOLIB_COMPLEX
+
 static inline int gpio_request(unsigned gpio, const char *label)
 {
 	return 0;
@@ -70,6 +72,7 @@ static inline void gpio_set_value(unsigned gpio, int value)
 #include <asm-generic/gpio.h>			/* cansleep wrappers */
 
 extern int gpio_to_irq(int gpio);
+#define gpio_to_irq gpio_to_irq
 extern int irq_to_gpio(unsigned int irq);
 
 #endif
diff --git a/arch/arm/mach-ixp4xx/include/mach/io.h b/arch/arm/mach-ixp4xx/include/mach/io.h
index 57b5410c31f4..ffb9d6afb89f 100644
--- a/arch/arm/mach-ixp4xx/include/mach/io.h
+++ b/arch/arm/mach-ixp4xx/include/mach/io.h
@@ -17,8 +17,6 @@
 
 #include <mach/hardware.h>
 
-#define IO_SPACE_LIMIT 0x0000ffff
-
 extern int (*ixp4xx_pci_read)(u32 addr, u32 cmd, u32* data);
 extern int ixp4xx_pci_write(u32 addr, u32 cmd, u32 data);
 
diff --git a/arch/arm/mach-ixp4xx/nas100d-setup.c b/arch/arm/mach-ixp4xx/nas100d-setup.c
index 9f4669260d4c..de716fa1aab6 100644
--- a/arch/arm/mach-ixp4xx/nas100d-setup.c
+++ b/arch/arm/mach-ixp4xx/nas100d-setup.c
@@ -17,7 +17,7 @@
  * Maintainers: http://www.nslu2-linux.org/
  *
  */
-
+#include <linux/gpio.h>
 #include <linux/if_ether.h>
 #include <linux/irq.h>
 #include <linux/jiffies.h>
@@ -32,7 +32,6 @@
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/flash.h>
-#include <asm/gpio.h>
 
 #define NAS100D_SDA_PIN		5
 #define NAS100D_SCL_PIN		6
diff --git a/arch/arm/mach-ixp4xx/nslu2-setup.c b/arch/arm/mach-ixp4xx/nslu2-setup.c
index 3676fbf6ef9c..ac81ccb26bfe 100644
--- a/arch/arm/mach-ixp4xx/nslu2-setup.c
+++ b/arch/arm/mach-ixp4xx/nslu2-setup.c
@@ -16,7 +16,7 @@
  * Maintainers: http://www.nslu2-linux.org/
  *
  */
-
+#include <linux/gpio.h>
 #include <linux/if_ether.h>
 #include <linux/irq.h>
 #include <linux/serial.h>
@@ -30,7 +30,6 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/flash.h>
 #include <asm/mach/time.h>
-#include <asm/gpio.h>
 
 #define NSLU2_SDA_PIN		7
 #define NSLU2_SCL_PIN		6
diff --git a/arch/arm/mach-kirkwood/irq.c b/arch/arm/mach-kirkwood/irq.c
index 05d193a25b25..c4c68e5b94f1 100644
--- a/arch/arm/mach-kirkwood/irq.c
+++ b/arch/arm/mach-kirkwood/irq.c
@@ -7,14 +7,13 @@
  * License version 2.  This program is licensed "as is" without any
  * warranty of any kind, whether express or implied.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/irq.h>
 #include <linux/io.h>
 #include <mach/bridge-regs.h>
 #include <plat/irq.h>
-#include <asm/gpio.h>
 #include "common.h"
 
 static void gpio_irq_handler(unsigned int irq, struct irq_desc *desc)
diff --git a/arch/arm/mach-kirkwood/mpp.c b/arch/arm/mach-kirkwood/mpp.c
index b0a7d979a8ed..cc431fa22ccb 100644
--- a/arch/arm/mach-kirkwood/mpp.c
+++ b/arch/arm/mach-kirkwood/mpp.c
@@ -7,12 +7,11 @@
  * License version 2.  This program is licensed "as is" without any
  * warranty of any kind, whether express or implied.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/mbus.h>
 #include <linux/io.h>
-#include <asm/gpio.h>
 #include <mach/hardware.h>
 #include <plat/mpp.h>
 #include "common.h"
diff --git a/arch/arm/mach-ks8695/Makefile b/arch/arm/mach-ks8695/Makefile
index 7e3e8160ed30..853efd9133c6 100644
--- a/arch/arm/mach-ks8695/Makefile
+++ b/arch/arm/mach-ks8695/Makefile
@@ -3,7 +3,7 @@
 # Makefile for KS8695 architecture support
 #
 
-obj-y				:= cpu.o irq.o time.o gpio.o devices.o
+obj-y				:= cpu.o irq.o time.o devices.o
 obj-m				:=
 obj-n				:=
 obj-				:=
diff --git a/arch/arm/mach-ks8695/board-acs5k.c b/arch/arm/mach-ks8695/board-acs5k.c
index a5fcc7c7fe18..a91f99d265aa 100644
--- a/arch/arm/mach-ks8695/board-acs5k.c
+++ b/arch/arm/mach-ks8695/board-acs5k.c
@@ -10,7 +10,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/types.h>
 #include <linux/interrupt.h>
@@ -34,7 +34,7 @@
 #include <asm/mach/irq.h>
 
 #include <mach/devices.h>
-#include <mach/gpio.h>
+#include <mach/gpio-ks8695.h>
 
 #include "generic.h"
 
diff --git a/arch/arm/mach-ks8695/board-dsm320.c b/arch/arm/mach-ks8695/board-dsm320.c
index fb91a716a7db..d24bcef2e2dd 100644
--- a/arch/arm/mach-ks8695/board-dsm320.c
+++ b/arch/arm/mach-ks8695/board-dsm320.c
@@ -10,7 +10,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/types.h>
 #include <linux/interrupt.h>
@@ -29,7 +29,7 @@
 #include <asm/mach/irq.h>
 
 #include <mach/devices.h>
-#include <mach/gpio.h>
+#include <mach/gpio-ks8695.h>
 
 #include "generic.h"
 
diff --git a/arch/arm/mach-ks8695/board-micrel.c b/arch/arm/mach-ks8695/board-micrel.c
index 8f67a750b6c7..16c95657f8fd 100644
--- a/arch/arm/mach-ks8695/board-micrel.c
+++ b/arch/arm/mach-ks8695/board-micrel.c
@@ -5,7 +5,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/types.h>
 #include <linux/interrupt.h>
@@ -18,7 +18,7 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/gpio.h>
+#include <mach/gpio-ks8695.h>
 #include <mach/devices.h>
 
 #include "generic.h"
diff --git a/arch/arm/mach-ks8695/devices.c b/arch/arm/mach-ks8695/devices.c
index b89fb6d46ccc..73bd63812878 100644
--- a/arch/arm/mach-ks8695/devices.c
+++ b/arch/arm/mach-ks8695/devices.c
@@ -20,6 +20,7 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 
 #include <mach/irqs.h>
diff --git a/arch/arm/mach-ks8695/include/mach/gpio-ks8695.h b/arch/arm/mach-ks8695/include/mach/gpio-ks8695.h
new file mode 100644
index 000000000000..6eb034d60325
--- /dev/null
+++ b/arch/arm/mach-ks8695/include/mach/gpio-ks8695.h
@@ -0,0 +1,39 @@
+/*
+ * Copyright (C) 2006 Andrew Victor
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __MACH_KS8659_GPIO_H
+#define __MACH_KS8659_GPIO_H
+
+#include <linux/kernel.h>
+
+#define KS8695_GPIO_0		0
+#define KS8695_GPIO_1		1
+#define KS8695_GPIO_2		2
+#define KS8695_GPIO_3		3
+#define KS8695_GPIO_4		4
+#define KS8695_GPIO_5		5
+#define KS8695_GPIO_6		6
+#define KS8695_GPIO_7		7
+#define KS8695_GPIO_8		8
+#define KS8695_GPIO_9		9
+#define KS8695_GPIO_10		10
+#define KS8695_GPIO_11		11
+#define KS8695_GPIO_12		12
+#define KS8695_GPIO_13		13
+#define KS8695_GPIO_14		14
+#define KS8695_GPIO_15		15
+
+/*
+ * Configure GPIO pin as external interrupt source.
+ */
+extern int ks8695_gpio_interrupt(unsigned int pin, unsigned int type);
+
+/* Register the GPIOs */
+extern void ks8695_register_gpios(void);
+
+#endif /* __MACH_KS8659_GPIO_H */
diff --git a/arch/arm/mach-ks8695/include/mach/gpio.h b/arch/arm/mach-ks8695/include/mach/gpio.h
index 86312d476bc6..f5fda36e4512 100644
--- a/arch/arm/mach-ks8695/include/mach/gpio.h
+++ b/arch/arm/mach-ks8695/include/mach/gpio.h
@@ -11,47 +11,9 @@
 #ifndef __ASM_ARCH_GPIO_H_
 #define __ASM_ARCH_GPIO_H_
 
-#include <linux/kernel.h>
-
-#define KS8695_GPIO_0		0
-#define KS8695_GPIO_1		1
-#define KS8695_GPIO_2		2
-#define KS8695_GPIO_3		3
-#define KS8695_GPIO_4		4
-#define KS8695_GPIO_5		5
-#define KS8695_GPIO_6		6
-#define KS8695_GPIO_7		7
-#define KS8695_GPIO_8		8
-#define KS8695_GPIO_9		9
-#define KS8695_GPIO_10		10
-#define KS8695_GPIO_11		11
-#define KS8695_GPIO_12		12
-#define KS8695_GPIO_13		13
-#define KS8695_GPIO_14		14
-#define KS8695_GPIO_15		15
-
-/*
- * Configure GPIO pin as external interrupt source.
- */
-extern int ks8695_gpio_interrupt(unsigned int pin, unsigned int type);
-
 /*
  * Map IRQ number to GPIO line.
  */
 extern int irq_to_gpio(unsigned int irq);
 
-#include <asm-generic/gpio.h>
-
-/* If it turns out that we need to optimise GPIO access for the
- * Micrel's GPIOs, then these can be changed to check their argument
- * directly as static inlines. However for now it's probably not
- * worthwhile.
- */
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_to_irq __gpio_to_irq
-
-/* Register the GPIOs */
-extern void ks8695_register_gpios(void);
-
 #endif
diff --git a/arch/arm/mach-ks8695/leds.c b/arch/arm/mach-ks8695/leds.c
index 184ef74e4bee..d6f6502ac9b5 100644
--- a/arch/arm/mach-ks8695/leds.c
+++ b/arch/arm/mach-ks8695/leds.c
@@ -7,14 +7,14 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/init.h>
+#include <linux/gpio.h>
 
 #include <asm/leds.h>
 #include <mach/devices.h>
-#include <mach/gpio.h>
 
 
 static inline void ks8695_led_on(unsigned int led)
diff --git a/arch/arm/mach-lpc32xx/Makefile b/arch/arm/mach-lpc32xx/Makefile
index a5fc5d0eeaeb..f5db805ab958 100644
--- a/arch/arm/mach-lpc32xx/Makefile
+++ b/arch/arm/mach-lpc32xx/Makefile
@@ -3,6 +3,6 @@
 #
 
 obj-y	:= timer.o irq.o common.o serial.o clock.o
-obj-y	+= gpiolib.o pm.o suspend.o
+obj-y	+= pm.o suspend.o
 obj-y	+= phy3250.o
 
diff --git a/arch/arm/mach-lpc32xx/include/mach/gpio-lpc32xx.h b/arch/arm/mach-lpc32xx/include/mach/gpio-lpc32xx.h
new file mode 100644
index 000000000000..1816e22a3479
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/include/mach/gpio-lpc32xx.h
@@ -0,0 +1,50 @@
+/*
+ * Author: Kevin Wells <kevin.wells@nxp.com>
+ *
+ * Copyright (C) 2010 NXP Semiconductors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __MACH_GPIO_LPC32XX_H
+#define __MACH_GPIO_LPC32XX_H
+
+/*
+ * Note!
+ * Muxed GP pins need to be setup to the GP state in the board level
+ * code prior to using this driver.
+ * GPI pins : 28xP3 group
+ * GPO pins : 24xP3 group
+ * GPIO pins: 8xP0 group, 24xP1 group, 13xP2 group, 6xP3 group
+ */
+
+#define LPC32XX_GPIO_P0_MAX 8
+#define LPC32XX_GPIO_P1_MAX 24
+#define LPC32XX_GPIO_P2_MAX 13
+#define LPC32XX_GPIO_P3_MAX 6
+#define LPC32XX_GPI_P3_MAX 28
+#define LPC32XX_GPO_P3_MAX 24
+
+#define LPC32XX_GPIO_P0_GRP 0
+#define LPC32XX_GPIO_P1_GRP (LPC32XX_GPIO_P0_GRP + LPC32XX_GPIO_P0_MAX)
+#define LPC32XX_GPIO_P2_GRP (LPC32XX_GPIO_P1_GRP + LPC32XX_GPIO_P1_MAX)
+#define LPC32XX_GPIO_P3_GRP (LPC32XX_GPIO_P2_GRP + LPC32XX_GPIO_P2_MAX)
+#define LPC32XX_GPI_P3_GRP (LPC32XX_GPIO_P3_GRP + LPC32XX_GPIO_P3_MAX)
+#define LPC32XX_GPO_P3_GRP (LPC32XX_GPI_P3_GRP + LPC32XX_GPI_P3_MAX)
+
+/*
+ * A specific GPIO can be selected with this macro
+ * ie, GPIO_05 can be selected with LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 5)
+ * See the LPC32x0 User's guide for GPIO group numbers
+ */
+#define LPC32XX_GPIO(x, y) ((x) + (y))
+
+#endif /* __MACH_GPIO_LPC32XX_H */
diff --git a/arch/arm/mach-lpc32xx/include/mach/gpio.h b/arch/arm/mach-lpc32xx/include/mach/gpio.h
index 67d03da1eee9..e69de29bb2d1 100644
--- a/arch/arm/mach-lpc32xx/include/mach/gpio.h
+++ b/arch/arm/mach-lpc32xx/include/mach/gpio.h
@@ -1,74 +0,0 @@
-/*
- * arch/arm/mach-lpc32xx/include/mach/gpio.h
- *
- * Author: Kevin Wells <kevin.wells@nxp.com>
- *
- * Copyright (C) 2010 NXP Semiconductors
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#ifndef __ASM_ARCH_GPIO_H
-#define __ASM_ARCH_GPIO_H
-
-#include <asm-generic/gpio.h>
-
-/*
- * Note!
- * Muxed GP pins need to be setup to the GP state in the board level
- * code prior to using this driver.
- * GPI pins : 28xP3 group
- * GPO pins : 24xP3 group
- * GPIO pins: 8xP0 group, 24xP1 group, 13xP2 group, 6xP3 group
- */
-
-#define LPC32XX_GPIO_P0_MAX 8
-#define LPC32XX_GPIO_P1_MAX 24
-#define LPC32XX_GPIO_P2_MAX 13
-#define LPC32XX_GPIO_P3_MAX 6
-#define LPC32XX_GPI_P3_MAX 28
-#define LPC32XX_GPO_P3_MAX 24
-
-#define LPC32XX_GPIO_P0_GRP 0
-#define LPC32XX_GPIO_P1_GRP (LPC32XX_GPIO_P0_GRP + LPC32XX_GPIO_P0_MAX)
-#define LPC32XX_GPIO_P2_GRP (LPC32XX_GPIO_P1_GRP + LPC32XX_GPIO_P1_MAX)
-#define LPC32XX_GPIO_P3_GRP (LPC32XX_GPIO_P2_GRP + LPC32XX_GPIO_P2_MAX)
-#define LPC32XX_GPI_P3_GRP (LPC32XX_GPIO_P3_GRP + LPC32XX_GPIO_P3_MAX)
-#define LPC32XX_GPO_P3_GRP (LPC32XX_GPI_P3_GRP + LPC32XX_GPI_P3_MAX)
-
-/*
- * A specific GPIO can be selected with this macro
- * ie, GPIO_05 can be selected with LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 5)
- * See the LPC32x0 User's guide for GPIO group numbers
- */
-#define LPC32XX_GPIO(x, y) ((x) + (y))
-
-static inline int gpio_get_value(unsigned gpio)
-{
-	return __gpio_get_value(gpio);
-}
-
-static inline void gpio_set_value(unsigned gpio, int value)
-{
-	__gpio_set_value(gpio, value);
-}
-
-static inline int gpio_cansleep(unsigned gpio)
-{
-	return __gpio_cansleep(gpio);
-}
-
-static inline int gpio_to_irq(unsigned gpio)
-{
-	return __gpio_to_irq(gpio);
-}
-
-#endif
diff --git a/arch/arm/mach-lpc32xx/phy3250.c b/arch/arm/mach-lpc32xx/phy3250.c
index 9b621e14d16a..6d2f0d1b9373 100644
--- a/arch/arm/mach-lpc32xx/phy3250.c
+++ b/arch/arm/mach-lpc32xx/phy3250.c
@@ -37,6 +37,7 @@
 
 #include <mach/hardware.h>
 #include <mach/platform.h>
+#include <mach/gpio-lpc32xx.h>
 #include "common.h"
 
 /*
diff --git a/arch/arm/mach-mmp/aspenite.c b/arch/arm/mach-mmp/aspenite.c
index 06b5fa853c93..833c3a2784aa 100644
--- a/arch/arm/mach-mmp/aspenite.c
+++ b/arch/arm/mach-mmp/aspenite.c
@@ -8,7 +8,7 @@
  *  it under the terms of the GNU General Public License version 2 as
  *  publishhed by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/kernel.h>
 #include <linux/platform_device.h>
@@ -17,13 +17,13 @@
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/nand.h>
 #include <linux/interrupt.h>
+#include <linux/gpio.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <mach/addr-map.h>
 #include <mach/mfp-pxa168.h>
 #include <mach/pxa168.h>
-#include <mach/gpio.h>
 #include <video/pxa168fb.h>
 #include <linux/input.h>
 #include <plat/pxa27x_keypad.h>
diff --git a/arch/arm/mach-mmp/brownstone.c b/arch/arm/mach-mmp/brownstone.c
index c79162a50f28..e411252e3d39 100644
--- a/arch/arm/mach-mmp/brownstone.c
+++ b/arch/arm/mach-mmp/brownstone.c
@@ -14,7 +14,6 @@
 #include <linux/kernel.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
-#include <linux/gpio.h>
 #include <linux/regulator/machine.h>
 #include <linux/regulator/max8649.h>
 #include <linux/regulator/fixed.h>
diff --git a/arch/arm/mach-mmp/gplugd.c b/arch/arm/mach-mmp/gplugd.c
index 98e25d9aaab6..32776f3739f1 100644
--- a/arch/arm/mach-mmp/gplugd.c
+++ b/arch/arm/mach-mmp/gplugd.c
@@ -9,11 +9,11 @@
  */
 
 #include <linux/init.h>
+#include <linux/gpio.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach-types.h>
 
-#include <mach/gpio.h>
 #include <mach/pxa168.h>
 #include <mach/mfp-pxa168.h>
 
diff --git a/arch/arm/mach-mmp/include/mach/gpio-pxa.h b/arch/arm/mach-mmp/include/mach/gpio-pxa.h
new file mode 100644
index 000000000000..c017a983eced
--- /dev/null
+++ b/arch/arm/mach-mmp/include/mach/gpio-pxa.h
@@ -0,0 +1,30 @@
+#ifndef __ASM_MACH_GPIO_PXA_H
+#define __ASM_MACH_GPIO_PXA_H
+
+#include <mach/addr-map.h>
+#include <mach/irqs.h>
+
+#define GPIO_REGS_VIRT	(APB_VIRT_BASE + 0x19000)
+
+#define BANK_OFF(n)	(((n) < 3) ? (n) << 2 : 0x100 + (((n) - 3) << 2))
+#define GPIO_REG(x)	(*((volatile u32 *)(GPIO_REGS_VIRT + (x))))
+
+#define NR_BUILTIN_GPIO		IRQ_GPIO_NUM
+
+#define gpio_to_bank(gpio)	((gpio) >> 5)
+
+/* NOTE: these macros are defined here to make optimization of
+ * gpio_{get,set}_value() to work when 'gpio' is a constant.
+ * Usage of these macros otherwise is no longer recommended,
+ * use generic GPIO API whenever possible.
+ */
+#define GPIO_bit(gpio)	(1 << ((gpio) & 0x1f))
+
+#define GPLR(x)		GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x00)
+#define GPDR(x)		GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x0c)
+#define GPSR(x)		GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x18)
+#define GPCR(x)		GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x24)
+
+#include <plat/gpio-pxa.h>
+
+#endif /* __ASM_MACH_GPIO_PXA_H */
diff --git a/arch/arm/mach-mmp/include/mach/gpio.h b/arch/arm/mach-mmp/include/mach/gpio.h
index 7bfb827f3fe3..681262359d1c 100644
--- a/arch/arm/mach-mmp/include/mach/gpio.h
+++ b/arch/arm/mach-mmp/include/mach/gpio.h
@@ -1,36 +1,13 @@
 #ifndef __ASM_MACH_GPIO_H
 #define __ASM_MACH_GPIO_H
 
-#include <mach/addr-map.h>
-#include <mach/irqs.h>
 #include <asm-generic/gpio.h>
 
-#define GPIO_REGS_VIRT	(APB_VIRT_BASE + 0x19000)
-
-#define BANK_OFF(n)	(((n) < 3) ? (n) << 2 : 0x100 + (((n) - 3) << 2))
-#define GPIO_REG(x)	(*((volatile u32 *)(GPIO_REGS_VIRT + (x))))
-
-#define NR_BUILTIN_GPIO		IRQ_GPIO_NUM
-
-#define gpio_to_bank(gpio)	((gpio) >> 5)
 #define gpio_to_irq(gpio)	(IRQ_GPIO_START + (gpio))
 #define irq_to_gpio(irq)	((irq) - IRQ_GPIO_START)
 
-
 #define __gpio_is_inverted(gpio)	(0)
 #define __gpio_is_occupied(gpio)	(0)
 
-/* NOTE: these macros are defined here to make optimization of
- * gpio_{get,set}_value() to work when 'gpio' is a constant.
- * Usage of these macros otherwise is no longer recommended,
- * use generic GPIO API whenever possible.
- */
-#define GPIO_bit(gpio)	(1 << ((gpio) & 0x1f))
-
-#define GPLR(x)		GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x00)
-#define GPDR(x)		GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x0c)
-#define GPSR(x)		GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x18)
-#define GPCR(x)		GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x24)
-
 #include <plat/gpio.h>
 #endif /* __ASM_MACH_GPIO_H */
diff --git a/arch/arm/mach-mmp/jasper.c b/arch/arm/mach-mmp/jasper.c
index 5d6421d63254..8bfac6612623 100644
--- a/arch/arm/mach-mmp/jasper.c
+++ b/arch/arm/mach-mmp/jasper.c
@@ -14,7 +14,6 @@
 #include <linux/kernel.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
-#include <linux/gpio.h>
 #include <linux/regulator/machine.h>
 #include <linux/regulator/max8649.h>
 #include <linux/mfd/max8925.h>
diff --git a/arch/arm/mach-mmp/mmp2.c b/arch/arm/mach-mmp/mmp2.c
index 079c18861d5c..65d8689e40c9 100644
--- a/arch/arm/mach-mmp/mmp2.c
+++ b/arch/arm/mach-mmp/mmp2.c
@@ -9,7 +9,6 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -25,7 +24,7 @@
 #include <mach/irqs.h>
 #include <mach/dma.h>
 #include <mach/mfp.h>
-#include <mach/gpio.h>
+#include <mach/gpio-pxa.h>
 #include <mach/devices.h>
 #include <mach/mmp2.h>
 
diff --git a/arch/arm/mach-mmp/pxa168.c b/arch/arm/mach-mmp/pxa168.c
index 0156f535dae7..50c1763911ff 100644
--- a/arch/arm/mach-mmp/pxa168.c
+++ b/arch/arm/mach-mmp/pxa168.c
@@ -7,7 +7,6 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -21,7 +20,7 @@
 #include <mach/regs-apbc.h>
 #include <mach/regs-apmu.h>
 #include <mach/irqs.h>
-#include <mach/gpio.h>
+#include <mach/gpio-pxa.h>
 #include <mach/dma.h>
 #include <mach/devices.h>
 #include <mach/mfp.h>
diff --git a/arch/arm/mach-mmp/pxa910.c b/arch/arm/mach-mmp/pxa910.c
index 1464607aa60d..4ebbfbba39fc 100644
--- a/arch/arm/mach-mmp/pxa910.c
+++ b/arch/arm/mach-mmp/pxa910.c
@@ -7,7 +7,6 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -20,7 +19,7 @@
 #include <mach/regs-apmu.h>
 #include <mach/cputype.h>
 #include <mach/irqs.h>
-#include <mach/gpio.h>
+#include <mach/gpio-pxa.h>
 #include <mach/dma.h>
 #include <mach/mfp.h>
 #include <mach/devices.h>
diff --git a/arch/arm/mach-mmp/tavorevb.c b/arch/arm/mach-mmp/tavorevb.c
index c296b75c4453..eb5be879fd8c 100644
--- a/arch/arm/mach-mmp/tavorevb.c
+++ b/arch/arm/mach-mmp/tavorevb.c
@@ -7,18 +7,18 @@
  *  it under the terms of the GNU General Public License version 2 as
  *  publishhed by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/kernel.h>
 #include <linux/platform_device.h>
 #include <linux/smc91x.h>
+#include <linux/gpio.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <mach/addr-map.h>
 #include <mach/mfp-pxa910.h>
 #include <mach/pxa910.h>
-#include <mach/gpio.h>
 
 #include "common.h"
 
diff --git a/arch/arm/mach-msm/board-msm7x27.c b/arch/arm/mach-msm/board-msm7x27.c
index a80765533f13..6d84ee740df4 100644
--- a/arch/arm/mach-msm/board-msm7x27.c
+++ b/arch/arm/mach-msm/board-msm7x27.c
@@ -13,7 +13,7 @@
  * GNU General Public License for more details.
  *
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -34,7 +34,6 @@
 
 #include <mach/vreg.h>
 #include <mach/mpp.h>
-#include <mach/gpio.h>
 #include <mach/board.h>
 #include <mach/msm_iomap.h>
 
diff --git a/arch/arm/mach-msm/board-msm7x30.c b/arch/arm/mach-msm/board-msm7x30.c
index bb72ea0383b7..71de5062c71e 100644
--- a/arch/arm/mach-msm/board-msm7x30.c
+++ b/arch/arm/mach-msm/board-msm7x30.c
@@ -14,7 +14,7 @@
  * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
  * 02110-1301, USA.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/irq.h>
 #include <linux/gpio.h>
@@ -31,7 +31,6 @@
 #include <asm/memory.h>
 #include <asm/setup.h>
 
-#include <mach/gpio.h>
 #include <mach/board.h>
 #include <mach/msm_iomap.h>
 #include <mach/dma.h>
diff --git a/arch/arm/mach-msm/board-qsd8x50.c b/arch/arm/mach-msm/board-qsd8x50.c
index 51109b1f4342..7e8909c978c3 100644
--- a/arch/arm/mach-msm/board-qsd8x50.c
+++ b/arch/arm/mach-msm/board-qsd8x50.c
@@ -14,7 +14,7 @@
  * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
  * 02110-1301, USA.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/irq.h>
 #include <linux/gpio.h>
@@ -32,7 +32,6 @@
 #include <mach/board.h>
 #include <mach/irqs.h>
 #include <mach/sirc.h>
-#include <mach/gpio.h>
 #include <mach/vreg.h>
 #include <mach/mmc.h>
 
diff --git a/arch/arm/mach-msm/board-sapphire.c b/arch/arm/mach-msm/board-sapphire.c
index dc0bcb5a6b9a..afa9293d5800 100644
--- a/arch/arm/mach-msm/board-sapphire.c
+++ b/arch/arm/mach-msm/board-sapphire.c
@@ -11,7 +11,7 @@
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
 */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -22,7 +22,6 @@
 
 #include <linux/delay.h>
 
-#include <asm/gpio.h>
 #include <mach/hardware.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
diff --git a/arch/arm/mach-msm/board-trout-mmc.c b/arch/arm/mach-msm/board-trout-mmc.c
index f7a9724788b0..8650342b7493 100644
--- a/arch/arm/mach-msm/board-trout-mmc.c
+++ b/arch/arm/mach-msm/board-trout-mmc.c
@@ -1,7 +1,7 @@
 /* linux/arch/arm/mach-msm/board-trout-mmc.c
 ** Author: Brian Swetland <swetland@google.com>
 */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -11,7 +11,6 @@
 #include <linux/err.h>
 #include <linux/debugfs.h>
 
-#include <asm/gpio.h>
 #include <asm/io.h>
 
 #include <mach/vreg.h>
diff --git a/arch/arm/mach-msm/board-trout-panel.c b/arch/arm/mach-msm/board-trout-panel.c
index 729bb49a44ca..25105c1027fe 100644
--- a/arch/arm/mach-msm/board-trout-panel.c
+++ b/arch/arm/mach-msm/board-trout-panel.c
@@ -1,7 +1,7 @@
 /* linux/arch/arm/mach-msm/board-trout-mddi.c
 ** Author: Brian Swetland <swetland@google.com>
 */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -11,7 +11,6 @@
 #include <linux/err.h>
 
 #include <asm/io.h>
-#include <asm/gpio.h>
 #include <asm/mach-types.h>
 
 #include <mach/msm_fb.h>
diff --git a/arch/arm/mach-msm/include/mach/gpio.h b/arch/arm/mach-msm/include/mach/gpio.h
index 36ad50d3bfaa..40a8c178f10d 100644
--- a/arch/arm/mach-msm/include/mach/gpio.h
+++ b/arch/arm/mach-msm/include/mach/gpio.h
@@ -1,26 +1 @@
-/*
- * Copyright (C) 2007 Google, Inc.
- * Copyright (c) 2009-2010, Code Aurora Forum. All rights reserved.
- * Author: Mike Lockwood <lockwood@android.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-#ifndef __ASM_ARCH_MSM_GPIO_H
-#define __ASM_ARCH_MSM_GPIO_H
-
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value  __gpio_get_value
-#define gpio_set_value  __gpio_set_value
-#define gpio_cansleep   __gpio_cansleep
-#define gpio_to_irq     __gpio_to_irq
-
-#endif /* __ASM_ARCH_MSM_GPIO_H */
+/* empty */
diff --git a/arch/arm/mach-mv78xx0/irq.c b/arch/arm/mach-mv78xx0/irq.c
index 3e24431bb5ea..e421b701663b 100644
--- a/arch/arm/mach-mv78xx0/irq.c
+++ b/arch/arm/mach-mv78xx0/irq.c
@@ -7,12 +7,11 @@
  * License version 2.  This program is licensed "as is" without any
  * warranty of any kind, whether express or implied.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/pci.h>
 #include <linux/irq.h>
-#include <asm/gpio.h>
 #include <mach/bridge-regs.h>
 #include <plat/irq.h>
 #include "common.h"
diff --git a/arch/arm/mach-mv78xx0/mpp.c b/arch/arm/mach-mv78xx0/mpp.c
index 59b7686b9209..cf4e494d44bf 100644
--- a/arch/arm/mach-mv78xx0/mpp.c
+++ b/arch/arm/mach-mv78xx0/mpp.c
@@ -7,13 +7,12 @@
  * License version 2.  This program is licensed "as is" without any
  * warranty of any kind, whether express or implied.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/mbus.h>
 #include <linux/io.h>
 #include <plat/mpp.h>
-#include <asm/gpio.h>
 #include <mach/hardware.h>
 #include "common.h"
 #include "mpp.h"
diff --git a/arch/arm/mach-mxs/include/mach/gpio.h b/arch/arm/mach-mxs/include/mach/gpio.h
index 56025aa0a639..40a8c178f10d 100644
--- a/arch/arm/mach-mxs/include/mach/gpio.h
+++ b/arch/arm/mach-mxs/include/mach/gpio.h
@@ -1,31 +1 @@
-/*
- * Copyright 2007 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright 2008 Juergen Beisert, kernel@pengutronix.de
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA  02110-1301, USA.
- */
-
-#ifndef __MACH_MXS_GPIO_H__
-#define __MACH_MXS_GPIO_H__
-
-#include <asm-generic/gpio.h>
-
-/* use gpiolib dispatchers */
-#define gpio_get_value		__gpio_get_value
-#define gpio_set_value		__gpio_set_value
-#define gpio_cansleep		__gpio_cansleep
-#define gpio_to_irq		__gpio_to_irq
-
-#endif /* __MACH_MXS_GPIO_H__ */
+/* empty */
diff --git a/arch/arm/mach-nomadik/board-nhk8815.c b/arch/arm/mach-nomadik/board-nhk8815.c
index 398a75f62bee..0cbb74c96ef7 100644
--- a/arch/arm/mach-nomadik/board-nhk8815.c
+++ b/arch/arm/mach-nomadik/board-nhk8815.c
@@ -27,6 +27,7 @@
 #include <asm/mach/irq.h>
 #include <asm/mach/flash.h>
 
+#include <plat/gpio-nomadik.h>
 #include <plat/mtu.h>
 
 #include <mach/setup.h>
diff --git a/arch/arm/mach-nomadik/cpu-8815.c b/arch/arm/mach-nomadik/cpu-8815.c
index ac58e3b03b1a..dc67717db6f0 100644
--- a/arch/arm/mach-nomadik/cpu-8815.c
+++ b/arch/arm/mach-nomadik/cpu-8815.c
@@ -21,8 +21,8 @@
 #include <linux/device.h>
 #include <linux/amba/bus.h>
 #include <linux/platform_device.h>
-#include <linux/gpio.h>
 
+#include <plat/gpio-nomadik.h>
 #include <mach/hardware.h>
 #include <mach/irqs.h>
 #include <asm/mach/map.h>
diff --git a/arch/arm/mach-nomadik/i2c-8815nhk.c b/arch/arm/mach-nomadik/i2c-8815nhk.c
index abfe25a08d6b..0fc2f6f1cc97 100644
--- a/arch/arm/mach-nomadik/i2c-8815nhk.c
+++ b/arch/arm/mach-nomadik/i2c-8815nhk.c
@@ -3,8 +3,8 @@
 #include <linux/i2c.h>
 #include <linux/i2c-algo-bit.h>
 #include <linux/i2c-gpio.h>
-#include <linux/gpio.h>
 #include <linux/platform_device.h>
+#include <plat/gpio-nomadik.h>
 
 /*
  * There are two busses in the 8815NHK.
diff --git a/arch/arm/mach-nomadik/include/mach/gpio.h b/arch/arm/mach-nomadik/include/mach/gpio.h
index 7a81a0420343..efdde0ae0a4f 100644
--- a/arch/arm/mach-nomadik/include/mach/gpio.h
+++ b/arch/arm/mach-nomadik/include/mach/gpio.h
@@ -1,6 +1,4 @@
 #ifndef __ASM_ARCH_GPIO_H
 #define __ASM_ARCH_GPIO_H
 
-#include <plat/gpio.h>
-
 #endif /* __ASM_ARCH_GPIO_H */
diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c
index eb36b25450a0..4ea60e2038ea 100644
--- a/arch/arm/mach-omap1/board-ams-delta.c
+++ b/arch/arm/mach-omap1/board-ams-delta.c
@@ -11,7 +11,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/input.h>
@@ -30,7 +30,6 @@
 
 #include <plat/io.h>
 #include <plat/board-ams-delta.h>
-#include <mach/gpio.h>
 #include <plat/keypad.h>
 #include <plat/mux.h>
 #include <plat/usb.h>
diff --git a/arch/arm/mach-omap1/board-fsample.c b/arch/arm/mach-omap1/board-fsample.c
index 999789c4811d..31e089b6f03f 100644
--- a/arch/arm/mach-omap1/board-fsample.c
+++ b/arch/arm/mach-omap1/board-fsample.c
@@ -10,7 +10,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -28,7 +28,6 @@
 #include <asm/mach/map.h>
 
 #include <plat/tc.h>
-#include <mach/gpio.h>
 #include <plat/mux.h>
 #include <plat/flash.h>
 #include <plat/fpga.h>
diff --git a/arch/arm/mach-omap1/board-generic.c b/arch/arm/mach-omap1/board-generic.c
index 23cc9e4ad50d..05c6e9d858f3 100644
--- a/arch/arm/mach-omap1/board-generic.c
+++ b/arch/arm/mach-omap1/board-generic.c
@@ -12,7 +12,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -22,7 +22,6 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <mach/gpio.h>
 #include <plat/mux.h>
 #include <plat/usb.h>
 #include <plat/board.h>
diff --git a/arch/arm/mach-omap1/board-h2-mmc.c b/arch/arm/mach-omap1/board-h2-mmc.c
index f2fc43d8382b..da0e37d40823 100644
--- a/arch/arm/mach-omap1/board-h2-mmc.c
+++ b/arch/arm/mach-omap1/board-h2-mmc.c
@@ -11,13 +11,12 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 
 #include <linux/i2c/tps65010.h>
 
 #include <plat/mmc.h>
-#include <mach/gpio.h>
 
 #include "board-h2.h"
 
diff --git a/arch/arm/mach-omap1/board-h2.c b/arch/arm/mach-omap1/board-h2.c
index 6c70c28d055c..c2e279173d42 100644
--- a/arch/arm/mach-omap1/board-h2.c
+++ b/arch/arm/mach-omap1/board-h2.c
@@ -18,7 +18,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/platform_device.h>
 #include <linux/delay.h>
@@ -32,7 +32,6 @@
 #include <linux/smc91x.h>
 
 #include <mach/hardware.h>
-#include <asm/gpio.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
diff --git a/arch/arm/mach-omap1/board-h3-mmc.c b/arch/arm/mach-omap1/board-h3-mmc.c
index 2098525e7cc5..f8242aa9b763 100644
--- a/arch/arm/mach-omap1/board-h3-mmc.c
+++ b/arch/arm/mach-omap1/board-h3-mmc.c
@@ -11,13 +11,12 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 
 #include <linux/i2c/tps65010.h>
 
 #include <plat/mmc.h>
-#include <mach/gpio.h>
 
 #include "board-h3.h"
 
diff --git a/arch/arm/mach-omap1/board-h3.c b/arch/arm/mach-omap1/board-h3.c
index 8e2b64a46929..8f5b6af7ed59 100644
--- a/arch/arm/mach-omap1/board-h3.c
+++ b/arch/arm/mach-omap1/board-h3.c
@@ -13,7 +13,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/types.h>
 #include <linux/init.h>
 #include <linux/major.h>
@@ -34,7 +34,6 @@
 #include <asm/setup.h>
 #include <asm/page.h>
 #include <mach/hardware.h>
-#include <asm/gpio.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
diff --git a/arch/arm/mach-omap1/board-htcherald.c b/arch/arm/mach-omap1/board-htcherald.c
index e81ead1c89ea..fcd1a3c31896 100644
--- a/arch/arm/mach-omap1/board-htcherald.c
+++ b/arch/arm/mach-omap1/board-htcherald.c
@@ -23,7 +23,6 @@
  * 02110-1301, USA.
  *
  */
-
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
diff --git a/arch/arm/mach-omap1/board-innovator.c b/arch/arm/mach-omap1/board-innovator.c
index 8b034594fbc7..c2234caf8a7a 100644
--- a/arch/arm/mach-omap1/board-innovator.c
+++ b/arch/arm/mach-omap1/board-innovator.c
@@ -15,7 +15,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -34,7 +34,6 @@
 #include <plat/mux.h>
 #include <plat/flash.h>
 #include <plat/fpga.h>
-#include <mach/gpio.h>
 #include <plat/tc.h>
 #include <plat/usb.h>
 #include <plat/keypad.h>
diff --git a/arch/arm/mach-omap1/board-nokia770.c b/arch/arm/mach-omap1/board-nokia770.c
index 6825635ac681..02789c5d3703 100644
--- a/arch/arm/mach-omap1/board-nokia770.c
+++ b/arch/arm/mach-omap1/board-nokia770.c
@@ -7,7 +7,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/mutex.h>
@@ -26,7 +26,6 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <mach/gpio.h>
 #include <plat/mux.h>
 #include <plat/usb.h>
 #include <plat/board.h>
diff --git a/arch/arm/mach-omap1/board-osk.c b/arch/arm/mach-omap1/board-osk.c
index 44b8e9362bf4..e4dca1deebb4 100644
--- a/arch/arm/mach-omap1/board-osk.c
+++ b/arch/arm/mach-omap1/board-osk.c
@@ -25,7 +25,7 @@
  * with this program; if not, write  to the Free Software Foundation, Inc.,
  * 675 Mass Ave, Cambridge, MA 02139, USA.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -42,7 +42,6 @@
 #include <linux/i2c/tps65010.h>
 
 #include <mach/hardware.h>
-#include <asm/gpio.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
diff --git a/arch/arm/mach-omap1/board-palmte.c b/arch/arm/mach-omap1/board-palmte.c
index 3d8cd90b1dbb..50c4e398bcc8 100644
--- a/arch/arm/mach-omap1/board-palmte.c
+++ b/arch/arm/mach-omap1/board-palmte.c
@@ -16,7 +16,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/input.h>
@@ -33,7 +33,6 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <mach/gpio.h>
 #include <plat/flash.h>
 #include <plat/mux.h>
 #include <plat/usb.h>
diff --git a/arch/arm/mach-omap1/board-palmtt.c b/arch/arm/mach-omap1/board-palmtt.c
index d0eefe81cd1b..273771cb1b61 100644
--- a/arch/arm/mach-omap1/board-palmtt.c
+++ b/arch/arm/mach-omap1/board-palmtt.c
@@ -12,6 +12,7 @@
  */
 
 #include <linux/delay.h>
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -30,7 +31,6 @@
 #include <asm/mach/map.h>
 
 #include <plat/led.h>
-#include <mach/gpio.h>
 #include <plat/flash.h>
 #include <plat/mux.h>
 #include <plat/usb.h>
diff --git a/arch/arm/mach-omap1/board-palmz71.c b/arch/arm/mach-omap1/board-palmz71.c
index 98e79bc09213..de36ade38ef7 100644
--- a/arch/arm/mach-omap1/board-palmz71.c
+++ b/arch/arm/mach-omap1/board-palmz71.c
@@ -15,6 +15,7 @@
  */
 
 #include <linux/delay.h>
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -32,7 +33,6 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <mach/gpio.h>
 #include <plat/flash.h>
 #include <plat/mux.h>
 #include <plat/usb.h>
diff --git a/arch/arm/mach-omap1/board-perseus2.c b/arch/arm/mach-omap1/board-perseus2.c
index ad3a1567604e..04b1befaced6 100644
--- a/arch/arm/mach-omap1/board-perseus2.c
+++ b/arch/arm/mach-omap1/board-perseus2.c
@@ -10,7 +10,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -28,7 +28,6 @@
 #include <asm/mach/map.h>
 
 #include <plat/tc.h>
-#include <mach/gpio.h>
 #include <plat/mux.h>
 #include <plat/fpga.h>
 #include <plat/flash.h>
diff --git a/arch/arm/mach-omap1/board-sx1-mmc.c b/arch/arm/mach-omap1/board-sx1-mmc.c
index e8ddd86e3fda..b59f78850e69 100644
--- a/arch/arm/mach-omap1/board-sx1-mmc.c
+++ b/arch/arm/mach-omap1/board-sx1-mmc.c
@@ -12,11 +12,11 @@
  * published by the Free Software Foundation.
  */
 
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 
 #include <mach/hardware.h>
 #include <plat/mmc.h>
-#include <mach/gpio.h>
 #include <plat/board-sx1.h>
 
 #if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
diff --git a/arch/arm/mach-omap1/board-sx1.c b/arch/arm/mach-omap1/board-sx1.c
index 602b55c39d3d..2bea941741d5 100644
--- a/arch/arm/mach-omap1/board-sx1.c
+++ b/arch/arm/mach-omap1/board-sx1.c
@@ -14,7 +14,7 @@
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/input.h>
@@ -32,7 +32,6 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <mach/gpio.h>
 #include <plat/flash.h>
 #include <plat/mux.h>
 #include <plat/dma.h>
diff --git a/arch/arm/mach-omap1/board-voiceblue.c b/arch/arm/mach-omap1/board-voiceblue.c
index 80165154617a..940faed82be2 100644
--- a/arch/arm/mach-omap1/board-voiceblue.c
+++ b/arch/arm/mach-omap1/board-voiceblue.c
@@ -13,6 +13,7 @@
  */
 
 #include <linux/delay.h>
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/interrupt.h>
 #include <linux/irq.h>
@@ -33,7 +34,6 @@
 
 #include <plat/board-voiceblue.h>
 #include <plat/common.h>
-#include <mach/gpio.h>
 #include <plat/flash.h>
 #include <plat/mux.h>
 #include <plat/tc.h>
diff --git a/arch/arm/mach-omap1/devices.c b/arch/arm/mach-omap1/devices.c
index 36f26c3fa25e..7c50ecf68123 100644
--- a/arch/arm/mach-omap1/devices.c
+++ b/arch/arm/mach-omap1/devices.c
@@ -10,6 +10,7 @@
  */
 
 #include <linux/dma-mapping.h>
+#include <linux/gpio.h>
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -24,7 +25,6 @@
 #include <plat/tc.h>
 #include <plat/board.h>
 #include <plat/mux.h>
-#include <mach/gpio.h>
 #include <plat/mmc.h>
 #include <plat/omap7xx.h>
 #include <plat/mcbsp.h>
diff --git a/arch/arm/mach-omap1/fpga.c b/arch/arm/mach-omap1/fpga.c
index cddbf8b089ce..0a17a1a7e00d 100644
--- a/arch/arm/mach-omap1/fpga.c
+++ b/arch/arm/mach-omap1/fpga.c
@@ -17,6 +17,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/kernel.h>
 #include <linux/device.h>
@@ -28,7 +29,6 @@
 #include <asm/mach/irq.h>
 
 #include <plat/fpga.h>
-#include <mach/gpio.h>
 
 static void fpga_mask_irq(struct irq_data *d)
 {
diff --git a/arch/arm/mach-omap1/irq.c b/arch/arm/mach-omap1/irq.c
index e2b9c901ab67..e5b104b7fce6 100644
--- a/arch/arm/mach-omap1/irq.c
+++ b/arch/arm/mach-omap1/irq.c
@@ -35,7 +35,7 @@
  * with this program; if not, write  to the Free Software Foundation, Inc.,
  * 675 Mass Ave, Cambridge, MA 02139, USA.
  */
-
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/module.h>
 #include <linux/sched.h>
@@ -45,7 +45,6 @@
 #include <mach/hardware.h>
 #include <asm/irq.h>
 #include <asm/mach/irq.h>
-#include <mach/gpio.h>
 #include <plat/cpu.h>
 
 #define IRQ_BANK(irq) ((irq) >> 5)
diff --git a/arch/arm/mach-omap1/leds-h2p2-debug.c b/arch/arm/mach-omap1/leds-h2p2-debug.c
index b4f9be52e1e8..4b818eb9f911 100644
--- a/arch/arm/mach-omap1/leds-h2p2-debug.c
+++ b/arch/arm/mach-omap1/leds-h2p2-debug.c
@@ -9,6 +9,7 @@
  * The "surfer" expansion board and H2 sample board also have two-color
  * green+red LEDs (in parallel), used here for timer and idle indicators.
  */
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/kernel_stat.h>
 #include <linux/sched.h>
@@ -20,7 +21,6 @@
 #include <asm/mach-types.h>
 
 #include <plat/fpga.h>
-#include <mach/gpio.h>
 
 #include "leds.h"
 
diff --git a/arch/arm/mach-omap1/leds-osk.c b/arch/arm/mach-omap1/leds-osk.c
index 499d7ad8697d..da09f4364979 100644
--- a/arch/arm/mach-omap1/leds-osk.c
+++ b/arch/arm/mach-omap1/leds-osk.c
@@ -3,14 +3,13 @@
  *
  * LED driver for OSK with optional Mistral QVGA board
  */
+#include <linux/gpio.h>
 #include <linux/init.h>
 
 #include <mach/hardware.h>
 #include <asm/leds.h>
 #include <asm/system.h>
 
-#include <mach/gpio.h>
-
 #include "leds.h"
 
 
diff --git a/arch/arm/mach-omap1/leds.c b/arch/arm/mach-omap1/leds.c
index 22eb11dde9e7..ae6dd93b8ddc 100644
--- a/arch/arm/mach-omap1/leds.c
+++ b/arch/arm/mach-omap1/leds.c
@@ -3,13 +3,13 @@
  *
  * OMAP LEDs dispatcher
  */
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 
 #include <asm/leds.h>
 #include <asm/mach-types.h>
 
-#include <mach/gpio.h>
 #include <plat/mux.h>
 
 #include "leds.h"
diff --git a/arch/arm/mach-omap1/serial.c b/arch/arm/mach-omap1/serial.c
index 550ca9d9991d..93ae8f29727e 100644
--- a/arch/arm/mach-omap1/serial.c
+++ b/arch/arm/mach-omap1/serial.c
@@ -7,7 +7,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -24,7 +24,6 @@
 
 #include <plat/board.h>
 #include <plat/mux.h>
-#include <mach/gpio.h>
 #include <plat/fpga.h>
 
 #include "pm.h"
diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c
index 0c427976d62f..67f0a122e18b 100644
--- a/arch/arm/mach-omap2/board-generic.c
+++ b/arch/arm/mach-omap2/board-generic.c
@@ -11,7 +11,10 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/device.h>
 #include <linux/io.h>
 #include <linux/of_platform.h>
 #include <linux/irqdomain.h>
@@ -20,6 +23,7 @@
 #include <mach/hardware.h>
 #include <asm/mach/arch.h>
 
+#include <plat/usb.h>
 #include <plat/board.h>
 #include <plat/common.h>
 #include <mach/omap4-common.h>
diff --git a/arch/arm/mach-omap2/board-h4.c b/arch/arm/mach-omap2/board-h4.c
index fe75c195f69f..a65effe7e8d5 100644
--- a/arch/arm/mach-omap2/board-h4.c
+++ b/arch/arm/mach-omap2/board-h4.c
@@ -10,7 +10,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -31,7 +31,6 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <mach/gpio.h>
 #include <plat/usb.h>
 #include <plat/board.h>
 #include <plat/common.h>
diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-ldp.c
index 0fa28be2cfda..57979175cff3 100644
--- a/arch/arm/mach-omap2/board-ldp.c
+++ b/arch/arm/mach-omap2/board-ldp.c
@@ -10,7 +10,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -34,7 +34,6 @@
 #include <asm/mach/map.h>
 
 #include <plat/mcspi.h>
-#include <mach/gpio.h>
 #include <plat/board.h>
 #include <plat/common.h>
 #include <plat/gpmc.h>
diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c
index 0f8e0eb18166..37b4ef8b07e8 100644
--- a/arch/arm/mach-omap2/devices.c
+++ b/arch/arm/mach-omap2/devices.c
@@ -8,7 +8,7 @@
  * the Free Software Foundation; either version 2 of the License, or
  * (at your option) any later version.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -27,7 +27,6 @@
 #include <plat/tc.h>
 #include <plat/board.h>
 #include <plat/mcbsp.h>
-#include <mach/gpio.h>
 #include <plat/mmc.h>
 #include <plat/dma.h>
 #include <plat/omap_hwmod.h>
diff --git a/arch/arm/mach-orion5x/db88f5281-setup.c b/arch/arm/mach-orion5x/db88f5281-setup.c
index 88432aba972c..4b79a80d5e1f 100644
--- a/arch/arm/mach-orion5x/db88f5281-setup.c
+++ b/arch/arm/mach-orion5x/db88f5281-setup.c
@@ -9,7 +9,7 @@
  * License version 2.  This program is licensed "as is" without any
  * warranty of any kind, whether express or implied.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -21,7 +21,6 @@
 #include <linux/mv643xx_eth.h>
 #include <linux/i2c.h>
 #include <asm/mach-types.h>
-#include <asm/gpio.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/pci.h>
 #include <mach/orion5x.h>
diff --git a/arch/arm/mach-orion5x/dns323-setup.c b/arch/arm/mach-orion5x/dns323-setup.c
index 9e5c1663fc4f..343f60e9639f 100644
--- a/arch/arm/mach-orion5x/dns323-setup.c
+++ b/arch/arm/mach-orion5x/dns323-setup.c
@@ -13,7 +13,7 @@
  * License, or (at your option) any later version.
  *
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/delay.h>
@@ -30,7 +30,6 @@
 #include <linux/phy.h>
 #include <linux/marvell_phy.h>
 #include <asm/mach-types.h>
-#include <asm/gpio.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/pci.h>
 #include <mach/orion5x.h>
diff --git a/arch/arm/mach-orion5x/irq.c b/arch/arm/mach-orion5x/irq.c
index 43cf8bc9767b..b1b45fff776e 100644
--- a/arch/arm/mach-orion5x/irq.c
+++ b/arch/arm/mach-orion5x/irq.c
@@ -9,12 +9,11 @@
  * License version 2.  This program is licensed "as is" without any
  * warranty of any kind, whether express or implied.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/irq.h>
 #include <linux/io.h>
-#include <asm/gpio.h>
 #include <mach/bridge-regs.h>
 #include <plat/irq.h>
 #include "common.h"
diff --git a/arch/arm/mach-orion5x/kurobox_pro-setup.c b/arch/arm/mach-orion5x/kurobox_pro-setup.c
index 9115511dc035..d3cd3f63258a 100644
--- a/arch/arm/mach-orion5x/kurobox_pro-setup.c
+++ b/arch/arm/mach-orion5x/kurobox_pro-setup.c
@@ -7,7 +7,7 @@
  * License version 2.  This program is licensed "as is" without any
  * warranty of any kind, whether express or implied.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -21,7 +21,6 @@
 #include <linux/serial_reg.h>
 #include <linux/ata_platform.h>
 #include <asm/mach-types.h>
-#include <asm/gpio.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/pci.h>
 #include <mach/orion5x.h>
diff --git a/arch/arm/mach-orion5x/mv2120-setup.c b/arch/arm/mach-orion5x/mv2120-setup.c
index b3356ada64b9..201ae3676289 100644
--- a/arch/arm/mach-orion5x/mv2120-setup.c
+++ b/arch/arm/mach-orion5x/mv2120-setup.c
@@ -7,7 +7,7 @@
  * published by the Free Software Foundation; either version 2 of the
  * License, or (at your option) any later version.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -20,7 +20,6 @@
 #include <linux/i2c.h>
 #include <linux/ata_platform.h>
 #include <asm/mach-types.h>
-#include <asm/gpio.h>
 #include <asm/mach/arch.h>
 #include <mach/orion5x.h>
 #include "common.h"
diff --git a/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c b/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c
index 8c876664f494..ebd6767d8e88 100644
--- a/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c
+++ b/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c
@@ -7,7 +7,7 @@
  * License version 2.  This program is licensed "as is" without any
  * warranty of any kind, whether express or implied.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -18,7 +18,6 @@
 #include <linux/ethtool.h>
 #include <net/dsa.h>
 #include <asm/mach-types.h>
-#include <asm/gpio.h>
 #include <asm/leds.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/pci.h>
diff --git a/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c b/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c
index 994644f59d8d..05db2d336b08 100644
--- a/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c
+++ b/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c
@@ -7,7 +7,7 @@
  * License version 2.  This program is licensed "as is" without any
  * warranty of any kind, whether express or implied.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -19,7 +19,6 @@
 #include <linux/i2c.h>
 #include <net/dsa.h>
 #include <asm/mach-types.h>
-#include <asm/gpio.h>
 #include <asm/leds.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/pci.h>
diff --git a/arch/arm/mach-orion5x/rd88f5182-setup.c b/arch/arm/mach-orion5x/rd88f5182-setup.c
index 1903d25ecae9..e47fa0578ae3 100644
--- a/arch/arm/mach-orion5x/rd88f5182-setup.c
+++ b/arch/arm/mach-orion5x/rd88f5182-setup.c
@@ -9,7 +9,7 @@
  * License version 2.  This program is licensed "as is" without any
  * warranty of any kind, whether express or implied.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -20,7 +20,6 @@
 #include <linux/ata_platform.h>
 #include <linux/i2c.h>
 #include <asm/mach-types.h>
-#include <asm/gpio.h>
 #include <asm/leds.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/pci.h>
diff --git a/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c b/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c
index e06fdae77f0a..64317251ec00 100644
--- a/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c
+++ b/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c
@@ -7,7 +7,7 @@
  * License version 2.  This program is licensed "as is" without any
  * warranty of any kind, whether express or implied.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -21,7 +21,6 @@
 #include <linux/ethtool.h>
 #include <net/dsa.h>
 #include <asm/mach-types.h>
-#include <asm/gpio.h>
 #include <asm/leds.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/pci.h>
diff --git a/arch/arm/mach-orion5x/terastation_pro2-setup.c b/arch/arm/mach-orion5x/terastation_pro2-setup.c
index 306183273eb9..29f1526f7b70 100644
--- a/arch/arm/mach-orion5x/terastation_pro2-setup.c
+++ b/arch/arm/mach-orion5x/terastation_pro2-setup.c
@@ -8,7 +8,7 @@
  * as published by the Free Software Foundation; either version
  * 2 of the License, or (at your option) any later version.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -20,7 +20,6 @@
 #include <linux/i2c.h>
 #include <linux/serial_reg.h>
 #include <asm/mach-types.h>
-#include <asm/gpio.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/pci.h>
 #include <mach/orion5x.h>
diff --git a/arch/arm/mach-orion5x/ts209-setup.c b/arch/arm/mach-orion5x/ts209-setup.c
index 3dbcd5ed77ef..31e51f9b4b64 100644
--- a/arch/arm/mach-orion5x/ts209-setup.c
+++ b/arch/arm/mach-orion5x/ts209-setup.c
@@ -8,7 +8,7 @@
  * as published by the Free Software Foundation; either version
  * 2 of the License, or (at your option) any later version.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -23,7 +23,6 @@
 #include <linux/serial_reg.h>
 #include <linux/ata_platform.h>
 #include <asm/mach-types.h>
-#include <asm/gpio.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/pci.h>
 #include <mach/orion5x.h>
diff --git a/arch/arm/mach-orion5x/ts409-setup.c b/arch/arm/mach-orion5x/ts409-setup.c
index 23c9e2e5e550..0fbcc14e09d7 100644
--- a/arch/arm/mach-orion5x/ts409-setup.c
+++ b/arch/arm/mach-orion5x/ts409-setup.c
@@ -11,7 +11,7 @@
  * as published by the Free Software Foundation; either version
  * 2 of the License, or (at your option) any later version.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -25,7 +25,6 @@
 #include <linux/i2c.h>
 #include <linux/serial_reg.h>
 #include <asm/mach-types.h>
-#include <asm/gpio.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/pci.h>
 #include <mach/orion5x.h>
diff --git a/arch/arm/mach-orion5x/wnr854t-setup.c b/arch/arm/mach-orion5x/wnr854t-setup.c
index 1c63a76f3ca3..b8be7d8d0cf4 100644
--- a/arch/arm/mach-orion5x/wnr854t-setup.c
+++ b/arch/arm/mach-orion5x/wnr854t-setup.c
@@ -5,7 +5,7 @@
  * License version 2.  This program is licensed "as is" without any
  * warranty of any kind, whether express or implied.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -17,7 +17,6 @@
 #include <linux/ethtool.h>
 #include <net/dsa.h>
 #include <asm/mach-types.h>
-#include <asm/gpio.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/pci.h>
 #include <mach/orion5x.h>
diff --git a/arch/arm/mach-orion5x/wrt350n-v2-setup.c b/arch/arm/mach-orion5x/wrt350n-v2-setup.c
index 4fd9f18c9d5d..faf81a039360 100644
--- a/arch/arm/mach-orion5x/wrt350n-v2-setup.c
+++ b/arch/arm/mach-orion5x/wrt350n-v2-setup.c
@@ -5,7 +5,7 @@
  * License version 2.  This program is licensed "as is" without any
  * warranty of any kind, whether express or implied.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -20,7 +20,6 @@
 #include <linux/input.h>
 #include <net/dsa.h>
 #include <asm/mach-types.h>
-#include <asm/gpio.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/pci.h>
 #include <mach/orion5x.h>
diff --git a/arch/arm/mach-pnx4008/gpio.c b/arch/arm/mach-pnx4008/gpio.c
index f219914f5b29..d3e71d3847b4 100644
--- a/arch/arm/mach-pnx4008/gpio.c
+++ b/arch/arm/mach-pnx4008/gpio.c
@@ -13,14 +13,13 @@
  * is licensed "as is" without any warranty of any kind, whether express
  * or implied.
  */
-
 #include <linux/types.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/io.h>
 #include <mach/hardware.h>
 #include <mach/platform.h>
-#include <mach/gpio.h>
+#include <mach/gpio-pnx4008.h>
 
 /* register definitions */
 #define PIO_VA_BASE	IO_ADDRESS(PNX4008_PIO_BASE)
diff --git a/arch/arm/mach-pnx4008/include/mach/gpio.h b/arch/arm/mach-pnx4008/include/mach/gpio-pnx4008.h
index 9591467eb9ec..41027dd7cf74 100644
--- a/arch/arm/mach-pnx4008/include/mach/gpio.h
+++ b/arch/arm/mach-pnx4008/include/mach/gpio-pnx4008.h
@@ -1,5 +1,5 @@
 /*
- * arch/arm/mach-pnx4008/include/mach/gpio.h
+ * arch/arm/mach-pnx4008/include/mach/gpio-pnx4008.h
  *
  * PNX4008 GPIO driver - header file
  *
diff --git a/arch/arm/mach-pnx4008/serial.c b/arch/arm/mach-pnx4008/serial.c
index f40961e51914..374c138ac1ac 100644
--- a/arch/arm/mach-pnx4008/serial.c
+++ b/arch/arm/mach-pnx4008/serial.c
@@ -9,7 +9,6 @@
  *  it under the terms of the GNU General Public License version 2 as
  *  published by the Free Software Foundation.
  */
-
 #include <linux/kernel.h>
 #include <linux/types.h>
 #include <linux/io.h>
@@ -19,8 +18,8 @@
 
 #include <linux/serial_core.h>
 #include <linux/serial_reg.h>
-#include <mach/gpio.h>
 
+#include <mach/gpio-pnx4008.h>
 #include <mach/clock.h>
 
 #define UART_3		0
diff --git a/arch/arm/mach-pxa/cm-x255.c b/arch/arm/mach-pxa/cm-x255.c
index 93f59f877fc6..be751470d37b 100644
--- a/arch/arm/mach-pxa/cm-x255.c
+++ b/arch/arm/mach-pxa/cm-x255.c
@@ -11,7 +11,6 @@
 
 #include <linux/platform_device.h>
 #include <linux/irq.h>
-#include <linux/gpio.h>
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/physmap.h>
 #include <linux/mtd/nand-gpio.h>
diff --git a/arch/arm/mach-pxa/generic.c b/arch/arm/mach-pxa/generic.c
index f5d91efc2965..5432ecb15def 100644
--- a/arch/arm/mach-pxa/generic.c
+++ b/arch/arm/mach-pxa/generic.c
@@ -16,6 +16,7 @@
  * initialization stuff for PXA machines which can be overridden later if
  * need be.
  */
+#include <linux/gpio.h>
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -26,7 +27,6 @@
 #include <asm/mach-types.h>
 
 #include <mach/reset.h>
-#include <mach/gpio.h>
 #include <mach/smemc.h>
 #include <mach/pxa3xx-regs.h>
 
diff --git a/arch/arm/mach-pxa/include/mach/gpio-pxa.h b/arch/arm/mach-pxa/include/mach/gpio-pxa.h
new file mode 100644
index 000000000000..41b4c93a96c2
--- /dev/null
+++ b/arch/arm/mach-pxa/include/mach/gpio-pxa.h
@@ -0,0 +1,133 @@
+/*
+ * Written by Philipp Zabel <philipp.zabel@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+#ifndef __MACH_PXA_GPIO_PXA_H
+#define __MACH_PXA_GPIO_PXA_H
+
+#include <mach/irqs.h>
+#include <mach/hardware.h>
+
+#define GPIO_REGS_VIRT	io_p2v(0x40E00000)
+
+#define BANK_OFF(n)	(((n) < 3) ? (n) << 2 : 0x100 + (((n) - 3) << 2))
+#define GPIO_REG(x)	(*(volatile u32 *)(GPIO_REGS_VIRT + (x)))
+
+/* GPIO Pin Level Registers */
+#define GPLR0		GPIO_REG(BANK_OFF(0) + 0x00)
+#define GPLR1		GPIO_REG(BANK_OFF(1) + 0x00)
+#define GPLR2		GPIO_REG(BANK_OFF(2) + 0x00)
+#define GPLR3		GPIO_REG(BANK_OFF(3) + 0x00)
+
+/* GPIO Pin Direction Registers */
+#define GPDR0		GPIO_REG(BANK_OFF(0) + 0x0c)
+#define GPDR1		GPIO_REG(BANK_OFF(1) + 0x0c)
+#define GPDR2		GPIO_REG(BANK_OFF(2) + 0x0c)
+#define GPDR3		GPIO_REG(BANK_OFF(3) + 0x0c)
+
+/* GPIO Pin Output Set Registers */
+#define GPSR0		GPIO_REG(BANK_OFF(0) + 0x18)
+#define GPSR1		GPIO_REG(BANK_OFF(1) + 0x18)
+#define GPSR2		GPIO_REG(BANK_OFF(2) + 0x18)
+#define GPSR3		GPIO_REG(BANK_OFF(3) + 0x18)
+
+/* GPIO Pin Output Clear Registers */
+#define GPCR0		GPIO_REG(BANK_OFF(0) + 0x24)
+#define GPCR1		GPIO_REG(BANK_OFF(1) + 0x24)
+#define GPCR2		GPIO_REG(BANK_OFF(2) + 0x24)
+#define GPCR3		GPIO_REG(BANK_OFF(3) + 0x24)
+
+/* GPIO Rising Edge Detect Registers */
+#define GRER0		GPIO_REG(BANK_OFF(0) + 0x30)
+#define GRER1		GPIO_REG(BANK_OFF(1) + 0x30)
+#define GRER2		GPIO_REG(BANK_OFF(2) + 0x30)
+#define GRER3		GPIO_REG(BANK_OFF(3) + 0x30)
+
+/* GPIO Falling Edge Detect Registers */
+#define GFER0		GPIO_REG(BANK_OFF(0) + 0x3c)
+#define GFER1		GPIO_REG(BANK_OFF(1) + 0x3c)
+#define GFER2		GPIO_REG(BANK_OFF(2) + 0x3c)
+#define GFER3		GPIO_REG(BANK_OFF(3) + 0x3c)
+
+/* GPIO Edge Detect Status Registers */
+#define GEDR0		GPIO_REG(BANK_OFF(0) + 0x48)
+#define GEDR1		GPIO_REG(BANK_OFF(1) + 0x48)
+#define GEDR2		GPIO_REG(BANK_OFF(2) + 0x48)
+#define GEDR3		GPIO_REG(BANK_OFF(3) + 0x48)
+
+/* GPIO Alternate Function Select Registers */
+#define GAFR0_L		GPIO_REG(0x0054)
+#define GAFR0_U		GPIO_REG(0x0058)
+#define GAFR1_L		GPIO_REG(0x005C)
+#define GAFR1_U		GPIO_REG(0x0060)
+#define GAFR2_L		GPIO_REG(0x0064)
+#define GAFR2_U		GPIO_REG(0x0068)
+#define GAFR3_L		GPIO_REG(0x006C)
+#define GAFR3_U		GPIO_REG(0x0070)
+
+/* More handy macros.  The argument is a literal GPIO number. */
+
+#define GPIO_bit(x)	(1 << ((x) & 0x1f))
+
+#define GPLR(x)		GPIO_REG(BANK_OFF((x) >> 5) + 0x00)
+#define GPDR(x)		GPIO_REG(BANK_OFF((x) >> 5) + 0x0c)
+#define GPSR(x)		GPIO_REG(BANK_OFF((x) >> 5) + 0x18)
+#define GPCR(x)		GPIO_REG(BANK_OFF((x) >> 5) + 0x24)
+#define GRER(x)		GPIO_REG(BANK_OFF((x) >> 5) + 0x30)
+#define GFER(x)		GPIO_REG(BANK_OFF((x) >> 5) + 0x3c)
+#define GEDR(x)		GPIO_REG(BANK_OFF((x) >> 5) + 0x48)
+#define GAFR(x)		GPIO_REG(0x54 + (((x) & 0x70) >> 2))
+
+
+#define NR_BUILTIN_GPIO		PXA_GPIO_IRQ_NUM
+
+#define gpio_to_bank(gpio)	((gpio) >> 5)
+
+#ifdef CONFIG_CPU_PXA26x
+/* GPIO86/87/88/89 on PXA26x have their direction bits in GPDR2 inverted,
+ * as well as their Alternate Function value being '1' for GPIO in GAFRx.
+ */
+static inline int __gpio_is_inverted(unsigned gpio)
+{
+	return cpu_is_pxa25x() && gpio > 85;
+}
+#else
+static inline int __gpio_is_inverted(unsigned gpio) { return 0; }
+#endif
+
+/*
+ * On PXA25x and PXA27x, GAFRx and GPDRx together decide the alternate
+ * function of a GPIO, and GPDRx cannot be altered once configured. It
+ * is attributed as "occupied" here (I know this terminology isn't
+ * accurate, you are welcome to propose a better one :-)
+ */
+static inline int __gpio_is_occupied(unsigned gpio)
+{
+	if (cpu_is_pxa27x() || cpu_is_pxa25x()) {
+		int af = (GAFR(gpio) >> ((gpio & 0xf) * 2)) & 0x3;
+		int dir = GPDR(gpio) & GPIO_bit(gpio);
+
+		if (__gpio_is_inverted(gpio))
+			return af != 1 || dir == 0;
+		else
+			return af != 0 || dir != 0;
+	} else
+		return GPDR(gpio) & GPIO_bit(gpio);
+}
+
+#include <plat/gpio-pxa.h>
+#endif /* __MACH_PXA_GPIO_PXA_H */
diff --git a/arch/arm/mach-pxa/include/mach/gpio.h b/arch/arm/mach-pxa/include/mach/gpio.h
index c4639502efca..004cade7bb13 100644
--- a/arch/arm/mach-pxa/include/mach/gpio.h
+++ b/arch/arm/mach-pxa/include/mach/gpio.h
@@ -24,84 +24,10 @@
 #ifndef __ASM_ARCH_PXA_GPIO_H
 #define __ASM_ARCH_PXA_GPIO_H
 
-#include <mach/irqs.h>
-#include <mach/hardware.h>
 #include <asm-generic/gpio.h>
+/* The defines for the driver are needed for the accelerated accessors */
+#include "gpio-pxa.h"
 
-#define GPIO_REGS_VIRT	io_p2v(0x40E00000)
-
-#define BANK_OFF(n)	(((n) < 3) ? (n) << 2 : 0x100 + (((n) - 3) << 2))
-#define GPIO_REG(x)	(*(volatile u32 *)(GPIO_REGS_VIRT + (x)))
-
-/* GPIO Pin Level Registers */
-#define GPLR0		GPIO_REG(BANK_OFF(0) + 0x00)
-#define GPLR1		GPIO_REG(BANK_OFF(1) + 0x00)
-#define GPLR2		GPIO_REG(BANK_OFF(2) + 0x00)
-#define GPLR3		GPIO_REG(BANK_OFF(3) + 0x00)
-
-/* GPIO Pin Direction Registers */
-#define GPDR0		GPIO_REG(BANK_OFF(0) + 0x0c)
-#define GPDR1		GPIO_REG(BANK_OFF(1) + 0x0c)
-#define GPDR2		GPIO_REG(BANK_OFF(2) + 0x0c)
-#define GPDR3		GPIO_REG(BANK_OFF(3) + 0x0c)
-
-/* GPIO Pin Output Set Registers */
-#define GPSR0		GPIO_REG(BANK_OFF(0) + 0x18)
-#define GPSR1		GPIO_REG(BANK_OFF(1) + 0x18)
-#define GPSR2		GPIO_REG(BANK_OFF(2) + 0x18)
-#define GPSR3		GPIO_REG(BANK_OFF(3) + 0x18)
-
-/* GPIO Pin Output Clear Registers */
-#define GPCR0		GPIO_REG(BANK_OFF(0) + 0x24)
-#define GPCR1		GPIO_REG(BANK_OFF(1) + 0x24)
-#define GPCR2		GPIO_REG(BANK_OFF(2) + 0x24)
-#define GPCR3		GPIO_REG(BANK_OFF(3) + 0x24)
-
-/* GPIO Rising Edge Detect Registers */
-#define GRER0		GPIO_REG(BANK_OFF(0) + 0x30)
-#define GRER1		GPIO_REG(BANK_OFF(1) + 0x30)
-#define GRER2		GPIO_REG(BANK_OFF(2) + 0x30)
-#define GRER3		GPIO_REG(BANK_OFF(3) + 0x30)
-
-/* GPIO Falling Edge Detect Registers */
-#define GFER0		GPIO_REG(BANK_OFF(0) + 0x3c)
-#define GFER1		GPIO_REG(BANK_OFF(1) + 0x3c)
-#define GFER2		GPIO_REG(BANK_OFF(2) + 0x3c)
-#define GFER3		GPIO_REG(BANK_OFF(3) + 0x3c)
-
-/* GPIO Edge Detect Status Registers */
-#define GEDR0		GPIO_REG(BANK_OFF(0) + 0x48)
-#define GEDR1		GPIO_REG(BANK_OFF(1) + 0x48)
-#define GEDR2		GPIO_REG(BANK_OFF(2) + 0x48)
-#define GEDR3		GPIO_REG(BANK_OFF(3) + 0x48)
-
-/* GPIO Alternate Function Select Registers */
-#define GAFR0_L		GPIO_REG(0x0054)
-#define GAFR0_U		GPIO_REG(0x0058)
-#define GAFR1_L		GPIO_REG(0x005C)
-#define GAFR1_U		GPIO_REG(0x0060)
-#define GAFR2_L		GPIO_REG(0x0064)
-#define GAFR2_U		GPIO_REG(0x0068)
-#define GAFR3_L		GPIO_REG(0x006C)
-#define GAFR3_U		GPIO_REG(0x0070)
-
-/* More handy macros.  The argument is a literal GPIO number. */
-
-#define GPIO_bit(x)	(1 << ((x) & 0x1f))
-
-#define GPLR(x)		GPIO_REG(BANK_OFF((x) >> 5) + 0x00)
-#define GPDR(x)		GPIO_REG(BANK_OFF((x) >> 5) + 0x0c)
-#define GPSR(x)		GPIO_REG(BANK_OFF((x) >> 5) + 0x18)
-#define GPCR(x)		GPIO_REG(BANK_OFF((x) >> 5) + 0x24)
-#define GRER(x)		GPIO_REG(BANK_OFF((x) >> 5) + 0x30)
-#define GFER(x)		GPIO_REG(BANK_OFF((x) >> 5) + 0x3c)
-#define GEDR(x)		GPIO_REG(BANK_OFF((x) >> 5) + 0x48)
-#define GAFR(x)		GPIO_REG(0x54 + (((x) & 0x70) >> 2))
-
-
-#define NR_BUILTIN_GPIO		PXA_GPIO_IRQ_NUM
-
-#define gpio_to_bank(gpio)	((gpio) >> 5)
 #define gpio_to_irq(gpio)	IRQ_GPIO(gpio)
 
 static inline int irq_to_gpio(unsigned int irq)
@@ -118,37 +44,5 @@ static inline int irq_to_gpio(unsigned int irq)
 	return -1;
 }
 
-#ifdef CONFIG_CPU_PXA26x
-/* GPIO86/87/88/89 on PXA26x have their direction bits in GPDR2 inverted,
- * as well as their Alternate Function value being '1' for GPIO in GAFRx.
- */
-static inline int __gpio_is_inverted(unsigned gpio)
-{
-	return cpu_is_pxa25x() && gpio > 85;
-}
-#else
-static inline int __gpio_is_inverted(unsigned gpio) { return 0; }
-#endif
-
-/*
- * On PXA25x and PXA27x, GAFRx and GPDRx together decide the alternate
- * function of a GPIO, and GPDRx cannot be altered once configured. It
- * is attributed as "occupied" here (I know this terminology isn't
- * accurate, you are welcome to propose a better one :-)
- */
-static inline int __gpio_is_occupied(unsigned gpio)
-{
-	if (cpu_is_pxa27x() || cpu_is_pxa25x()) {
-		int af = (GAFR(gpio) >> ((gpio & 0xf) * 2)) & 0x3;
-		int dir = GPDR(gpio) & GPIO_bit(gpio);
-
-		if (__gpio_is_inverted(gpio))
-			return af != 1 || dir == 0;
-		else
-			return af != 0 || dir != 0;
-	} else
-		return GPDR(gpio) & GPIO_bit(gpio);
-}
-
 #include <plat/gpio.h>
 #endif
diff --git a/arch/arm/mach-pxa/include/mach/littleton.h b/arch/arm/mach-pxa/include/mach/littleton.h
index 2a5726c15e0e..b6238cbd8aea 100644
--- a/arch/arm/mach-pxa/include/mach/littleton.h
+++ b/arch/arm/mach-pxa/include/mach/littleton.h
@@ -1,7 +1,7 @@
 #ifndef __ASM_ARCH_LITTLETON_H
 #define __ASM_ARCH_LITTLETON_H
 
-#include <mach/gpio.h>
+#include <mach/gpio-pxa.h>
 
 #define LITTLETON_ETH_PHYS	0x30000000
 
diff --git a/arch/arm/mach-pxa/irq.c b/arch/arm/mach-pxa/irq.c
index ca6075717824..8d9200f92268 100644
--- a/arch/arm/mach-pxa/irq.c
+++ b/arch/arm/mach-pxa/irq.c
@@ -11,7 +11,6 @@
  *  it under the terms of the GNU General Public License version 2 as
  *  published by the Free Software Foundation.
  */
-
 #include <linux/init.h>
 #include <linux/module.h>
 #include <linux/interrupt.h>
@@ -23,7 +22,7 @@
 
 #include <mach/hardware.h>
 #include <mach/irqs.h>
-#include <mach/gpio.h>
+#include <mach/gpio-pxa.h>
 
 #include "generic.h"
 
diff --git a/arch/arm/mach-pxa/lpd270.c b/arch/arm/mach-pxa/lpd270.c
index 16df0fc0879a..64540d908958 100644
--- a/arch/arm/mach-pxa/lpd270.c
+++ b/arch/arm/mach-pxa/lpd270.c
@@ -12,7 +12,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
 #include <linux/syscore_ops.h>
@@ -39,7 +39,6 @@
 #include <asm/mach/flash.h>
 
 #include <mach/pxa27x.h>
-#include <mach/gpio.h>
 #include <mach/lpd270.h>
 #include <mach/audio.h>
 #include <mach/pxafb.h>
diff --git a/arch/arm/mach-pxa/lubbock.c b/arch/arm/mach-pxa/lubbock.c
index a8c696bfc132..c48ce6da9184 100644
--- a/arch/arm/mach-pxa/lubbock.c
+++ b/arch/arm/mach-pxa/lubbock.c
@@ -11,6 +11,7 @@
  *  it under the terms of the GNU General Public License version 2 as
  *  published by the Free Software Foundation.
  */
+#include <linux/gpio.h>
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -42,7 +43,6 @@
 #include <asm/hardware/sa1111.h>
 
 #include <mach/pxa25x.h>
-#include <mach/gpio.h>
 #include <mach/audio.h>
 #include <mach/lubbock.h>
 #include <mach/udc.h>
diff --git a/arch/arm/mach-pxa/mainstone.c b/arch/arm/mach-pxa/mainstone.c
index cc6e14f6d114..0567d3965fda 100644
--- a/arch/arm/mach-pxa/mainstone.c
+++ b/arch/arm/mach-pxa/mainstone.c
@@ -12,7 +12,7 @@
  *  it under the terms of the GNU General Public License version 2 as
  *  published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
 #include <linux/syscore_ops.h>
@@ -43,7 +43,6 @@
 #include <asm/mach/flash.h>
 
 #include <mach/pxa27x.h>
-#include <mach/gpio.h>
 #include <mach/mainstone.h>
 #include <mach/audio.h>
 #include <mach/pxafb.h>
diff --git a/arch/arm/mach-pxa/mfp-pxa2xx.c b/arch/arm/mach-pxa/mfp-pxa2xx.c
index b27544bcafcb..43a5f6861ca3 100644
--- a/arch/arm/mach-pxa/mfp-pxa2xx.c
+++ b/arch/arm/mach-pxa/mfp-pxa2xx.c
@@ -12,15 +12,15 @@
  *  it under the terms of the GNU General Public License version 2 as
  *  published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/syscore_ops.h>
 
-#include <mach/gpio.h>
 #include <mach/pxa2xx-regs.h>
 #include <mach/mfp-pxa2xx.h>
+#include <mach/gpio-pxa.h>
 
 #include "generic.h"
 
diff --git a/arch/arm/mach-pxa/pcm990-baseboard.c b/arch/arm/mach-pxa/pcm990-baseboard.c
index 6d5b7e062124..9a9c539f6c01 100644
--- a/arch/arm/mach-pxa/pcm990-baseboard.c
+++ b/arch/arm/mach-pxa/pcm990-baseboard.c
@@ -19,7 +19,7 @@
  *  it under the terms of the GNU General Public License version 2 as
  *  published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/irq.h>
 #include <linux/platform_device.h>
 #include <linux/i2c.h>
@@ -28,7 +28,6 @@
 
 #include <media/soc_camera.h>
 
-#include <asm/gpio.h>
 #include <mach/camera.h>
 #include <asm/mach/map.h>
 #include <mach/pxa27x.h>
diff --git a/arch/arm/mach-pxa/pxa25x.c b/arch/arm/mach-pxa/pxa25x.c
index 9c434d21a271..8746e1090b6e 100644
--- a/arch/arm/mach-pxa/pxa25x.c
+++ b/arch/arm/mach-pxa/pxa25x.c
@@ -16,6 +16,7 @@
  * initialization stuff for PXA machines which can be overridden later if
  * need be.
  */
+#include <linux/gpio.h>
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -23,12 +24,12 @@
 #include <linux/suspend.h>
 #include <linux/syscore_ops.h>
 #include <linux/irq.h>
+#include <linux/gpio.h>
 
 #include <asm/mach/map.h>
 #include <asm/suspend.h>
 #include <mach/hardware.h>
 #include <mach/irqs.h>
-#include <mach/gpio.h>
 #include <mach/pxa25x.h>
 #include <mach/reset.h>
 #include <mach/pm.h>
diff --git a/arch/arm/mach-pxa/pxa27x.c b/arch/arm/mach-pxa/pxa27x.c
index 9d2400b5f503..2bb5cf8ba6ec 100644
--- a/arch/arm/mach-pxa/pxa27x.c
+++ b/arch/arm/mach-pxa/pxa27x.c
@@ -11,6 +11,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
+#include <linux/gpio.h>
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -20,13 +21,13 @@
 #include <linux/io.h>
 #include <linux/irq.h>
 #include <linux/i2c/pxa-i2c.h>
+#include <linux/gpio.h>
 
 #include <asm/mach/map.h>
 #include <mach/hardware.h>
 #include <asm/irq.h>
 #include <asm/suspend.h>
 #include <mach/irqs.h>
-#include <mach/gpio.h>
 #include <mach/pxa27x.h>
 #include <mach/reset.h>
 #include <mach/ohci.h>
diff --git a/arch/arm/mach-pxa/pxa3xx.c b/arch/arm/mach-pxa/pxa3xx.c
index b5cd9e5aba31..f940a1345531 100644
--- a/arch/arm/mach-pxa/pxa3xx.c
+++ b/arch/arm/mach-pxa/pxa3xx.c
@@ -12,7 +12,6 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -26,7 +25,7 @@
 #include <asm/mach/map.h>
 #include <asm/suspend.h>
 #include <mach/hardware.h>
-#include <mach/gpio.h>
+#include <mach/gpio-pxa.h>
 #include <mach/pxa3xx-regs.h>
 #include <mach/reset.h>
 #include <mach/ohci.h>
diff --git a/arch/arm/mach-pxa/pxa95x.c b/arch/arm/mach-pxa/pxa95x.c
index 0ee166b61f81..51371b39d2a3 100644
--- a/arch/arm/mach-pxa/pxa95x.c
+++ b/arch/arm/mach-pxa/pxa95x.c
@@ -9,7 +9,6 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -21,7 +20,7 @@
 #include <linux/syscore_ops.h>
 
 #include <mach/hardware.h>
-#include <mach/gpio.h>
+#include <mach/gpio-pxa.h>
 #include <mach/pxa3xx-regs.h>
 #include <mach/pxa930.h>
 #include <mach/reset.h>
diff --git a/arch/arm/mach-pxa/saarb.c b/arch/arm/mach-pxa/saarb.c
index 5ce340320ab9..3c988b6f718f 100644
--- a/arch/arm/mach-pxa/saarb.c
+++ b/arch/arm/mach-pxa/saarb.c
@@ -9,12 +9,13 @@
  *  it under the terms of the GNU General Public License version 2 as
  *  publishhed by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/kernel.h>
 #include <linux/i2c.h>
 #include <linux/i2c/pxa-i2c.h>
 #include <linux/mfd/88pm860x.h>
+#include <linux/gpio.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -23,7 +24,6 @@
 #include <mach/hardware.h>
 #include <mach/mfp.h>
 #include <mach/mfp-pxa930.h>
-#include <mach/gpio.h>
 
 #include "generic.h"
 
diff --git a/arch/arm/mach-realview/include/mach/gpio.h b/arch/arm/mach-realview/include/mach/gpio.h
index 94ff27678a46..40a8c178f10d 100644
--- a/arch/arm/mach-realview/include/mach/gpio.h
+++ b/arch/arm/mach-realview/include/mach/gpio.h
@@ -1,6 +1 @@
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value	__gpio_get_value
-#define gpio_set_value	__gpio_set_value
-#define gpio_cansleep	__gpio_cansleep
-#define gpio_to_irq	__gpio_to_irq
+/* empty */
diff --git a/arch/arm/mach-rpc/include/mach/hardware.h b/arch/arm/mach-rpc/include/mach/hardware.h
index dde6b3c0e299..050d63c74cc1 100644
--- a/arch/arm/mach-rpc/include/mach/hardware.h
+++ b/arch/arm/mach-rpc/include/mach/hardware.h
@@ -36,7 +36,7 @@
 
 #define EASI_SIZE		0x08000000	/* EASI I/O */
 #define EASI_START		0x08000000
-#define EASI_BASE		0xe5000000
+#define EASI_BASE		IOMEM(0xe5000000)
 
 #define IO_START		0x03000000	/* I/O */
 #define IO_SIZE			0x01000000
@@ -51,21 +51,20 @@
 /*
  * IO Addresses
  */
-#define VIDC_BASE		IOMEM(0xe0400000)
-#define EXPMASK_BASE		0xe0360000
-#define IOMD_BASE		IOMEM(0xe0200000)
-#define IOC_BASE		IOMEM(0xe0200000)
-#define PCIO_BASE		IOMEM(0xe0010000)
-#define FLOPPYDMA_BASE		IOMEM(0xe002a000)
+#define ECARD_EASI_BASE		(EASI_BASE)
+#define VIDC_BASE		(IO_BASE + 0x00400000)
+#define EXPMASK_BASE		(IO_BASE + 0x00360000)
+#define ECARD_IOC4_BASE		(IO_BASE + 0x00270000)
+#define ECARD_IOC_BASE		(IO_BASE + 0x00240000)
+#define IOMD_BASE		(IO_BASE + 0x00200000)
+#define IOC_BASE		(IO_BASE + 0x00200000)
+#define ECARD_MEMC8_BASE	(IO_BASE + 0x0002b000)
+#define FLOPPYDMA_BASE		(IO_BASE + 0x0002a000)
+#define PCIO_BASE		(IO_BASE + 0x00010000)
+#define ECARD_MEMC_BASE		(IO_BASE + 0x00000000)
 
 #define vidc_writel(val)	__raw_writel(val, VIDC_BASE)
 
-#define IO_EC_EASI_BASE		0x81400000
-#define IO_EC_IOC4_BASE		0x8009c000
-#define IO_EC_IOC_BASE		0x80090000
-#define IO_EC_MEMC8_BASE	0x8000ac00
-#define IO_EC_MEMC_BASE		0x80000000
-
 #define NETSLOT_BASE		0x0302b000
 #define NETSLOT_SIZE		0x00001000
 
diff --git a/arch/arm/mach-rpc/include/mach/io.h b/arch/arm/mach-rpc/include/mach/io.h
index 20da7f486e51..695f4ed2e11b 100644
--- a/arch/arm/mach-rpc/include/mach/io.h
+++ b/arch/arm/mach-rpc/include/mach/io.h
@@ -15,195 +15,18 @@
 
 #include <mach/hardware.h>
 
-#define IO_SPACE_LIMIT 0xffffffff
+#define IO_SPACE_LIMIT 0xffff
 
 /*
- * We use two different types of addressing - PC style addresses, and ARM
- * addresses.  PC style accesses the PC hardware with the normal PC IO
- * addresses, eg 0x3f8 for serial#1.  ARM addresses are 0x80000000+
- * and are translated to the start of IO.  Note that all addresses are
- * shifted left!
- */
-#define __PORT_PCIO(x)	(!((x) & 0x80000000))
-
-/*
- * Dynamic IO functions.
- */
-static inline void __outb (unsigned int value, unsigned int port)
-{
-	unsigned long temp;
-	__asm__ __volatile__(
-	"tst	%2, #0x80000000\n\t"
-	"mov	%0, %4\n\t"
-	"addeq	%0, %0, %3\n\t"
-	"strb	%1, [%0, %2, lsl #2]	@ outb"
-	: "=&r" (temp)
-	: "r" (value), "r" (port), "Ir" (PCIO_BASE - IO_BASE), "Ir" (IO_BASE)
-	: "cc");
-}
-
-static inline void __outw (unsigned int value, unsigned int port)
-{
-	unsigned long temp;
-	__asm__ __volatile__(
-	"tst	%2, #0x80000000\n\t"
-	"mov	%0, %4\n\t"
-	"addeq	%0, %0, %3\n\t"
-	"str	%1, [%0, %2, lsl #2]	@ outw"
-	: "=&r" (temp)
-	: "r" (value|value<<16), "r" (port), "Ir" (PCIO_BASE - IO_BASE), "Ir" (IO_BASE)
-	: "cc");
-}
-
-static inline void __outl (unsigned int value, unsigned int port)
-{
-	unsigned long temp;
-	__asm__ __volatile__(
-	"tst	%2, #0x80000000\n\t"
-	"mov	%0, %4\n\t"
-	"addeq	%0, %0, %3\n\t"
-	"str	%1, [%0, %2, lsl #2]	@ outl"
-	: "=&r" (temp)
-	: "r" (value), "r" (port), "Ir" (PCIO_BASE - IO_BASE), "Ir" (IO_BASE)
-	: "cc");
-}
-
-#define DECLARE_DYN_IN(sz,fnsuffix,instr)					\
-static inline unsigned sz __in##fnsuffix (unsigned int port)		\
-{										\
-	unsigned long temp, value;						\
-	__asm__ __volatile__(							\
-	"tst	%2, #0x80000000\n\t"						\
-	"mov	%0, %4\n\t"							\
-	"addeq	%0, %0, %3\n\t"							\
-	"ldr" instr "	%1, [%0, %2, lsl #2]	@ in" #fnsuffix			\
-	: "=&r" (temp), "=r" (value)						\
-	: "r" (port), "Ir" (PCIO_BASE - IO_BASE), "Ir" (IO_BASE)		\
-	: "cc");								\
-	return (unsigned sz)value;						\
-}
-
-static inline void __iomem *__deprecated __ioaddr(unsigned int port)
-{
-	void __iomem *ret;
-	if (__PORT_PCIO(port))
-		ret = PCIO_BASE;
-	else
-		ret = IO_BASE;
-	return ret + (port << 2);
-}
-
-#define DECLARE_IO(sz,fnsuffix,instr)	\
-	DECLARE_DYN_IN(sz,fnsuffix,instr)
-
-DECLARE_IO(char,b,"b")
-DECLARE_IO(short,w,"")
-DECLARE_IO(int,l,"")
-
-#undef DECLARE_IO
-#undef DECLARE_DYN_IN
-
-/*
- * Constant address IO functions
+ * We need PC style IO addressing for:
+ *  - floppy (at 0x3f2,0x3f4,0x3f5,0x3f7)
+ *  - parport (at 0x278-0x27a, 0x27b-0x27f, 0x778-0x77a)
+ *  - 8250 serial (only for compile)
  *
- * These have to be macros for the 'J' constraint to work -
- * +/-4096 immediate operand.
+ * These peripherals are found in an area of MMIO which looks very much
+ * like an ISA bus, but with registers at the low byte of each word.
  */
-#define __outbc(value,port)							\
-({										\
-	if (__PORT_PCIO((port)))						\
-		__asm__ __volatile__(						\
-		"strb	%0, [%1, %2]	@ outbc"				\
-		: : "r" (value), "r" (PCIO_BASE), "Jr" ((port) << 2));		\
-	else									\
-		__asm__ __volatile__(						\
-		"strb	%0, [%1, %2]	@ outbc"				\
-		: : "r" (value), "r" (IO_BASE), "r" ((port) << 2));		\
-})
-
-#define __inbc(port)								\
-({										\
-	unsigned char result;							\
-	if (__PORT_PCIO((port)))						\
-		__asm__ __volatile__(						\
-		"ldrb	%0, [%1, %2]	@ inbc"					\
-		: "=r" (result) : "r" (PCIO_BASE), "Jr" ((port) << 2));		\
-	else									\
-		__asm__ __volatile__(						\
-		"ldrb	%0, [%1, %2]	@ inbc"					\
-		: "=r" (result) : "r" (IO_BASE), "r" ((port) << 2));		\
-	result;									\
-})
-
-#define __outwc(value,port)							\
-({										\
-	unsigned long __v = value;						\
-	if (__PORT_PCIO((port)))						\
-		__asm__ __volatile__(						\
-		"str	%0, [%1, %2]	@ outwc"				\
-		: : "r" (__v|__v<<16), "r" (PCIO_BASE), "Jr" ((port) << 2));	\
-	else									\
-		__asm__ __volatile__(						\
-		"str	%0, [%1, %2]	@ outwc"				\
-		: : "r" (__v|__v<<16), "r" (IO_BASE), "r" ((port) << 2));		\
-})
-
-#define __inwc(port)								\
-({										\
-	unsigned short result;							\
-	if (__PORT_PCIO((port)))						\
-		__asm__ __volatile__(						\
-		"ldr	%0, [%1, %2]	@ inwc"					\
-		: "=r" (result) : "r" (PCIO_BASE), "Jr" ((port) << 2));		\
-	else									\
-		__asm__ __volatile__(						\
-		"ldr	%0, [%1, %2]	@ inwc"					\
-		: "=r" (result) : "r" (IO_BASE), "r" ((port) << 2));		\
-	result & 0xffff;							\
-})
-
-#define __outlc(value,port)							\
-({										\
-	unsigned long __v = value;						\
-	if (__PORT_PCIO((port)))						\
-		__asm__ __volatile__(						\
-		"str	%0, [%1, %2]	@ outlc"				\
-		: : "r" (__v), "r" (PCIO_BASE), "Jr" ((port) << 2));		\
-	else									\
-		__asm__ __volatile__(						\
-		"str	%0, [%1, %2]	@ outlc"				\
-		: : "r" (__v), "r" (IO_BASE), "r" ((port) << 2));		\
-})
-
-#define __inlc(port)								\
-({										\
-	unsigned long result;							\
-	if (__PORT_PCIO((port)))						\
-		__asm__ __volatile__(						\
-		"ldr	%0, [%1, %2]	@ inlc"					\
-		: "=r" (result) : "r" (PCIO_BASE), "Jr" ((port) << 2));		\
-	else									\
-		__asm__ __volatile__(						\
-		"ldr	%0, [%1, %2]	@ inlc"					\
-		: "=r" (result) : "r" (IO_BASE), "r" ((port) << 2));		\
-	result;									\
-})
-
-#define inb(p)	 	(__builtin_constant_p((p)) ? __inbc(p)    : __inb(p))
-#define inw(p)	 	(__builtin_constant_p((p)) ? __inwc(p)    : __inw(p))
-#define inl(p)	 	(__builtin_constant_p((p)) ? __inlc(p)    : __inl(p))
-#define outb(v,p)	(__builtin_constant_p((p)) ? __outbc(v,p) : __outb(v,p))
-#define outw(v,p)	(__builtin_constant_p((p)) ? __outwc(v,p) : __outw(v,p))
-#define outl(v,p)	(__builtin_constant_p((p)) ? __outlc(v,p) : __outl(v,p))
-
-/* the following macro is deprecated */
-#define ioaddr(port)	((unsigned long)__ioaddr((port)))
-
-#define insb(p,d,l)	__raw_readsb(__ioaddr(p),d,l)
-#define insw(p,d,l)	__raw_readsw(__ioaddr(p),d,l)
-
-#define outsb(p,d,l)	__raw_writesb(__ioaddr(p),d,l)
-#define outsw(p,d,l)	__raw_writesw(__ioaddr(p),d,l)
+#define __io(a)		(PCIO_BASE + ((a) << 2))
 
 /*
  * 1:1 mapping for ioremapped regions.
diff --git a/arch/arm/mach-rpc/riscpc.c b/arch/arm/mach-rpc/riscpc.c
index a9241eb87724..8559598ab767 100644
--- a/arch/arm/mach-rpc/riscpc.c
+++ b/arch/arm/mach-rpc/riscpc.c
@@ -74,7 +74,7 @@ static struct map_desc rpc_io_desc[] __initdata = {
 		.length		= 	IO_SIZE	 ,
 		.type		= MT_DEVICE
 	}, {	/* EASI space	*/
-		.virtual	= EASI_BASE,
+		.virtual	= (unsigned long)EASI_BASE,
 		.pfn		= __phys_to_pfn(EASI_START),
 		.length		= EASI_SIZE,
 		.type		= MT_DEVICE
diff --git a/arch/arm/mach-s3c2410/include/mach/gpio.h b/arch/arm/mach-s3c2410/include/mach/gpio.h
index f7f6b07df30e..6fac70f3484e 100644
--- a/arch/arm/mach-s3c2410/include/mach/gpio.h
+++ b/arch/arm/mach-s3c2410/include/mach/gpio.h
@@ -11,11 +11,6 @@
  * published by the Free Software Foundation.
 */
 
-#define gpio_get_value	__gpio_get_value
-#define gpio_set_value	__gpio_set_value
-#define gpio_cansleep	__gpio_cansleep
-#define gpio_to_irq	__gpio_to_irq
-
 /* some boards require extra gpio capacity to support external
  * devices that need GPIO.
  */
@@ -28,7 +23,6 @@
 #define ARCH_NR_GPIOS	(256 + CONFIG_S3C24XX_GPIO_EXTRA)
 #endif
 
-#include <asm-generic/gpio.h>
 #include <mach/gpio-nrs.h>
 #include <mach/gpio-fns.h>
 
diff --git a/arch/arm/mach-s3c2410/include/mach/h1940-latch.h b/arch/arm/mach-s3c2410/include/mach/h1940-latch.h
index 97e42bfce81e..fc897d3a056c 100644
--- a/arch/arm/mach-s3c2410/include/mach/h1940-latch.h
+++ b/arch/arm/mach-s3c2410/include/mach/h1940-latch.h
@@ -14,7 +14,7 @@
 #ifndef __ASM_ARCH_H1940_LATCH_H
 #define __ASM_ARCH_H1940_LATCH_H
 
-#include <mach/gpio.h>
+#include <asm/gpio.h>
 
 #define H1940_LATCH_GPIO(x)		(S3C_GPIO_END + (x))
 
diff --git a/arch/arm/mach-s3c2410/include/mach/io.h b/arch/arm/mach-s3c2410/include/mach/io.h
index 9813dbf2ae4f..118749f37c4c 100644
--- a/arch/arm/mach-s3c2410/include/mach/io.h
+++ b/arch/arm/mach-s3c2410/include/mach/io.h
@@ -199,8 +199,6 @@ DECLARE_IO(int,l,"")
 #define outw(v,p)	(__builtin_constant_p((p)) ? __outwc(v,p) : __outw(v,p))
 #define outl(v,p)	(__builtin_constant_p((p)) ? __outlc(v,p) : __outl(v,p))
 #define __ioaddr(p)	(__builtin_constant_p((p)) ? __ioaddr(p)  : __ioaddrc(p))
-/* the following macro is deprecated */
-#define ioaddr(port)	__ioaddr((port))
 
 #define insb(p,d,l)	__raw_readsb(__ioaddr(p),d,l)
 #define insw(p,d,l)	__raw_readsw(__ioaddr(p),d,l)
diff --git a/arch/arm/mach-s3c64xx/include/mach/gpio.h b/arch/arm/mach-s3c64xx/include/mach/gpio.h
index 0d46e994048a..6e34c2f6e670 100644
--- a/arch/arm/mach-s3c64xx/include/mach/gpio.h
+++ b/arch/arm/mach-s3c64xx/include/mach/gpio.h
@@ -12,11 +12,6 @@
  * published by the Free Software Foundation.
 */
 
-#define gpio_get_value	__gpio_get_value
-#define gpio_set_value	__gpio_set_value
-#define gpio_cansleep	__gpio_cansleep
-#define gpio_to_irq	__gpio_to_irq
-
 /* GPIO bank sizes */
 #define S3C64XX_GPIO_A_NR	(8)
 #define S3C64XX_GPIO_B_NR	(7)
@@ -96,5 +91,3 @@ enum s3c_gpio_number {
 #define BOARD_NR_GPIOS 16
 
 #define ARCH_NR_GPIOS	(GPIO_BOARD_START + BOARD_NR_GPIOS)
-
-#include <asm-generic/gpio.h>
diff --git a/arch/arm/mach-s5p64x0/include/mach/gpio.h b/arch/arm/mach-s5p64x0/include/mach/gpio.h
index adb5f298ead8..06cd3c9b16ac 100644
--- a/arch/arm/mach-s5p64x0/include/mach/gpio.h
+++ b/arch/arm/mach-s5p64x0/include/mach/gpio.h
@@ -13,11 +13,6 @@
 #ifndef __ASM_ARCH_GPIO_H
 #define __ASM_ARCH_GPIO_H __FILE__
 
-#define gpio_get_value	__gpio_get_value
-#define gpio_set_value	__gpio_set_value
-#define gpio_cansleep	__gpio_cansleep
-#define gpio_to_irq	__gpio_to_irq
-
 /* GPIO bank sizes */
 
 #define S5P6440_GPIO_A_NR	(6)
@@ -134,6 +129,4 @@ enum s5p6450_gpio_number {
 
 #define ARCH_NR_GPIOS		(S5P64X0_GPIO_END + CONFIG_SAMSUNG_GPIO_EXTRA)
 
-#include <asm-generic/gpio.h>
-
 #endif /* __ASM_ARCH_GPIO_H */
diff --git a/arch/arm/mach-s5pc100/include/mach/gpio.h b/arch/arm/mach-s5pc100/include/mach/gpio.h
index 29a8a12d9b4f..5e1a924b595f 100644
--- a/arch/arm/mach-s5pc100/include/mach/gpio.h
+++ b/arch/arm/mach-s5pc100/include/mach/gpio.h
@@ -15,11 +15,6 @@
 #ifndef __ASM_ARCH_GPIO_H
 #define __ASM_ARCH_GPIO_H __FILE__
 
-#define gpio_get_value	__gpio_get_value
-#define gpio_set_value	__gpio_set_value
-#define gpio_cansleep	__gpio_cansleep
-#define gpio_to_irq	__gpio_to_irq
-
 /* GPIO bank sizes */
 #define S5PC100_GPIO_A0_NR	(8)
 #define S5PC100_GPIO_A1_NR	(5)
@@ -146,6 +141,4 @@ enum s5p_gpio_number {
 /* define the number of gpios we need to the one after the MP04() range */
 #define ARCH_NR_GPIOS		(S5PC100_GPIO_END + 1)
 
-#include <asm-generic/gpio.h>
-
 #endif /* __ASM_ARCH_GPIO_H */
diff --git a/arch/arm/mach-s5pv210/include/mach/gpio.h b/arch/arm/mach-s5pv210/include/mach/gpio.h
index a5a1e331f8ed..6c8b903c02e4 100644
--- a/arch/arm/mach-s5pv210/include/mach/gpio.h
+++ b/arch/arm/mach-s5pv210/include/mach/gpio.h
@@ -13,11 +13,6 @@
 #ifndef __ASM_ARCH_GPIO_H
 #define __ASM_ARCH_GPIO_H __FILE__
 
-#define gpio_get_value	__gpio_get_value
-#define gpio_set_value	__gpio_set_value
-#define gpio_cansleep	__gpio_cansleep
-#define gpio_to_irq	__gpio_to_irq
-
 /* Practically, GPIO banks up to MP03 are the configurable gpio banks */
 
 /* GPIO bank sizes */
@@ -142,6 +137,4 @@ enum s5p_gpio_number {
 #define ARCH_NR_GPIOS		(S5PV210_MP05(S5PV210_GPIO_MP05_NR) +	\
 				 CONFIG_SAMSUNG_GPIO_EXTRA + 1)
 
-#include <asm-generic/gpio.h>
-
 #endif /* __ASM_ARCH_GPIO_H */
diff --git a/arch/arm/mach-sa1100/Makefile b/arch/arm/mach-sa1100/Makefile
index 41252d22e659..73a5c6431792 100644
--- a/arch/arm/mach-sa1100/Makefile
+++ b/arch/arm/mach-sa1100/Makefile
@@ -3,7 +3,7 @@
 #
 
 # Common support
-obj-y := clock.o generic.o gpio.o irq.o dma.o time.o #nmi-oopser.o
+obj-y := clock.o generic.o irq.o dma.o time.o #nmi-oopser.o
 obj-m :=
 obj-n :=
 obj-  :=
diff --git a/arch/arm/mach-sa1100/generic.c b/arch/arm/mach-sa1100/generic.c
index e21f3470eece..5fa5ae1f39e1 100644
--- a/arch/arm/mach-sa1100/generic.c
+++ b/arch/arm/mach-sa1100/generic.c
@@ -9,6 +9,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
+#include <linux/gpio.h>
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -24,7 +25,6 @@
 #include <asm/mach/map.h>
 #include <asm/mach/flash.h>
 #include <asm/irq.h>
-#include <asm/gpio.h>
 
 #include "generic.h"
 
diff --git a/arch/arm/mach-sa1100/include/mach/gpio.h b/arch/arm/mach-sa1100/include/mach/gpio.h
index 7befc104e9a9..703631887c94 100644
--- a/arch/arm/mach-sa1100/include/mach/gpio.h
+++ b/arch/arm/mach-sa1100/include/mach/gpio.h
@@ -28,6 +28,8 @@
 #include <asm/irq.h>
 #include <asm-generic/gpio.h>
 
+#define __ARM_GPIOLIB_COMPLEX
+
 static inline int gpio_get_value(unsigned gpio)
 {
 	if (__builtin_constant_p(gpio) && (gpio <= GPIO_MAX))
@@ -51,7 +53,5 @@ static inline void gpio_set_value(unsigned gpio, int value)
 
 #define gpio_to_irq(gpio)	((gpio < 11) ? (IRQ_GPIO0 + gpio) : \
 					(IRQ_GPIO11 - 11 + gpio))
-#define irq_to_gpio(irq)	((irq < IRQ_GPIO11_27) ? (irq - IRQ_GPIO0) : \
-					(irq - IRQ_GPIO11 + 11))
 
 #endif
diff --git a/arch/arm/mach-sa1100/include/mach/io.h b/arch/arm/mach-sa1100/include/mach/io.h
index d8b43f3dcd2d..dfc27ff08344 100644
--- a/arch/arm/mach-sa1100/include/mach/io.h
+++ b/arch/arm/mach-sa1100/include/mach/io.h
@@ -10,11 +10,9 @@
 #ifndef __ASM_ARM_ARCH_IO_H
 #define __ASM_ARM_ARCH_IO_H
 
-#define IO_SPACE_LIMIT 0xffffffff
-
 /*
- * We don't actually have real ISA nor PCI buses, but there is so many 
- * drivers out there that might just work if we fake them...
+ * __io() is required to be an equivalent mapping to __mem_pci() for
+ * SOC_COMMON to work.
  */
 #define __io(a)		__typesafe_io(a)
 #define __mem_pci(a)	(a)
diff --git a/arch/arm/mach-shmobile/include/mach/gpio.h b/arch/arm/mach-shmobile/include/mach/gpio.h
index 2b1bb9e43dda..7bf0890e16ba 100644
--- a/arch/arm/mach-shmobile/include/mach/gpio.h
+++ b/arch/arm/mach-shmobile/include/mach/gpio.h
@@ -18,31 +18,15 @@
 
 #ifdef CONFIG_GPIOLIB
 
-static inline int gpio_get_value(unsigned gpio)
-{
-	return __gpio_get_value(gpio);
-}
-
-static inline void gpio_set_value(unsigned gpio, int value)
-{
-	__gpio_set_value(gpio, value);
-}
-
-static inline int gpio_cansleep(unsigned gpio)
-{
-	return __gpio_cansleep(gpio);
-}
-
-static inline int gpio_to_irq(unsigned gpio)
-{
-	return __gpio_to_irq(gpio);
-}
-
 static inline int irq_to_gpio(unsigned int irq)
 {
 	return -ENOSYS;
 }
 
+#else
+
+#define __ARM_GPIOLIB_COMPLEX
+
 #endif /* CONFIG_GPIOLIB */
 
 #endif /* __ASM_ARCH_GPIO_H */
diff --git a/arch/arm/mach-tegra/board-harmony-pcie.c b/arch/arm/mach-tegra/board-harmony-pcie.c
index 9c27b95b8d86..6db7d699ef1c 100644
--- a/arch/arm/mach-tegra/board-harmony-pcie.c
+++ b/arch/arm/mach-tegra/board-harmony-pcie.c
@@ -24,12 +24,10 @@
 
 #include <mach/pinmux.h>
 #include "board.h"
+#include "board-harmony.h"
 
 #ifdef CONFIG_TEGRA_PCI
 
-/* GPIO 3 of the PMIC */
-#define EN_VDD_1V05_GPIO	(TEGRA_NR_GPIOS + 2)
-
 static int __init harmony_pcie_init(void)
 {
 	struct regulator *regulator = NULL;
@@ -38,11 +36,11 @@ static int __init harmony_pcie_init(void)
 	if (!machine_is_harmony())
 		return 0;
 
-	err = gpio_request(EN_VDD_1V05_GPIO, "EN_VDD_1V05");
+	err = gpio_request(TEGRA_GPIO_EN_VDD_1V05_GPIO, "EN_VDD_1V05");
 	if (err)
 		return err;
 
-	gpio_direction_output(EN_VDD_1V05_GPIO, 1);
+	gpio_direction_output(TEGRA_GPIO_EN_VDD_1V05_GPIO, 1);
 
 	regulator = regulator_get(NULL, "pex_clk");
 	if (IS_ERR_OR_NULL(regulator))
@@ -68,7 +66,7 @@ err_pcie:
 	regulator_disable(regulator);
 	regulator_put(regulator);
 err_reg:
-	gpio_free(EN_VDD_1V05_GPIO);
+	gpio_free(TEGRA_GPIO_EN_VDD_1V05_GPIO);
 
 	return err;
 }
diff --git a/arch/arm/mach-tegra/board-harmony.h b/arch/arm/mach-tegra/board-harmony.h
index d85142edaf6b..139d96c93843 100644
--- a/arch/arm/mach-tegra/board-harmony.h
+++ b/arch/arm/mach-tegra/board-harmony.h
@@ -17,6 +17,8 @@
 #ifndef _MACH_TEGRA_BOARD_HARMONY_H
 #define _MACH_TEGRA_BOARD_HARMONY_H
 
+#include <mach/gpio-tegra.h>
+
 #define HARMONY_GPIO_TPS6586X(_x_)	(TEGRA_NR_GPIOS + (_x_))
 #define HARMONY_GPIO_WM8903(_x_)	(HARMONY_GPIO_TPS6586X(4) + (_x_))
 
@@ -31,6 +33,7 @@
 #define TEGRA_GPIO_HP_DET		TEGRA_GPIO_PW2
 #define TEGRA_GPIO_INT_MIC_EN		TEGRA_GPIO_PX0
 #define TEGRA_GPIO_EXT_MIC_EN		TEGRA_GPIO_PX1
+#define TEGRA_GPIO_EN_VDD_1V05_GPIO	HARMONY_GPIO_TPS6586X(2)
 
 void harmony_pinmux_init(void);
 int harmony_regulator_init(void);
diff --git a/arch/arm/mach-tegra/board-paz00.h b/arch/arm/mach-tegra/board-paz00.h
index d4ff39ddaeb3..42ce8639b90c 100644
--- a/arch/arm/mach-tegra/board-paz00.h
+++ b/arch/arm/mach-tegra/board-paz00.h
@@ -17,6 +17,8 @@
 #ifndef _MACH_TEGRA_BOARD_PAZ00_H
 #define _MACH_TEGRA_BOARD_PAZ00_H
 
+#include <mach/gpio-tegra.h>
+
 #define TEGRA_GPIO_SD1_CD		TEGRA_GPIO_PV5
 #define TEGRA_GPIO_SD1_WP		TEGRA_GPIO_PH1
 #define TEGRA_GPIO_SD1_POWER		TEGRA_GPIO_PT3
diff --git a/arch/arm/mach-tegra/board-seaboard.h b/arch/arm/mach-tegra/board-seaboard.h
index d8415e1a8434..15b6c57361be 100644
--- a/arch/arm/mach-tegra/board-seaboard.h
+++ b/arch/arm/mach-tegra/board-seaboard.h
@@ -17,6 +17,8 @@
 #ifndef _MACH_TEGRA_BOARD_SEABOARD_H
 #define _MACH_TEGRA_BOARD_SEABOARD_H
 
+#include <mach/gpio-tegra.h>
+
 #define TEGRA_GPIO_SD2_CD		TEGRA_GPIO_PI5
 #define TEGRA_GPIO_SD2_WP		TEGRA_GPIO_PH1
 #define TEGRA_GPIO_SD2_POWER		TEGRA_GPIO_PI6
diff --git a/arch/arm/mach-tegra/board-trimslice-pinmux.c b/arch/arm/mach-tegra/board-trimslice-pinmux.c
index 47c596cdbf32..bcb1916e68b9 100644
--- a/arch/arm/mach-tegra/board-trimslice-pinmux.c
+++ b/arch/arm/mach-tegra/board-trimslice-pinmux.c
@@ -13,12 +13,11 @@
  * GNU General Public License for more details.
  *
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 
 #include <mach/pinmux.h>
-#include <mach/gpio.h>
 
 #include "gpio-names.h"
 #include "board-trimslice.h"
diff --git a/arch/arm/mach-tegra/board-trimslice.h b/arch/arm/mach-tegra/board-trimslice.h
index 7a7dee86b4da..50f128d87779 100644
--- a/arch/arm/mach-tegra/board-trimslice.h
+++ b/arch/arm/mach-tegra/board-trimslice.h
@@ -17,6 +17,8 @@
 #ifndef _MACH_TEGRA_BOARD_TRIMSLICE_H
 #define _MACH_TEGRA_BOARD_TRIMSLICE_H
 
+#include <mach/gpio-tegra.h>
+
 #define TRIMSLICE_GPIO_SD4_CD	TEGRA_GPIO_PP1	/* mmc4 cd */
 #define TRIMSLICE_GPIO_SD4_WP	TEGRA_GPIO_PP2	/* mmc4 wp */
 
diff --git a/arch/arm/mach-tegra/include/mach/gpio-tegra.h b/arch/arm/mach-tegra/include/mach/gpio-tegra.h
new file mode 100644
index 000000000000..87d37fdf5084
--- /dev/null
+++ b/arch/arm/mach-tegra/include/mach/gpio-tegra.h
@@ -0,0 +1,39 @@
+/*
+ * arch/arm/mach-tegra/include/mach/gpio.h
+ *
+ * Copyright (C) 2010 Google, Inc.
+ *
+ * Author:
+ *	Erik Gilling <konkers@google.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef __MACH_TEGRA_GPIO_TEGRA_H
+#define __MACH_TEGRA_GPIO_TEGRA_H
+
+#include <linux/types.h>
+#include <mach/irqs.h>
+
+#define TEGRA_NR_GPIOS		INT_GPIO_NR
+
+#define TEGRA_GPIO_TO_IRQ(gpio) (INT_GPIO_BASE + (gpio))
+
+struct tegra_gpio_table {
+	int	gpio;	/* GPIO number */
+	bool	enable;	/* Enable for GPIO at init? */
+};
+
+void tegra_gpio_config(struct tegra_gpio_table *table, int num);
+void tegra_gpio_enable(int gpio);
+void tegra_gpio_disable(int gpio);
+
+#endif
diff --git a/arch/arm/mach-tegra/include/mach/gpio.h b/arch/arm/mach-tegra/include/mach/gpio.h
index 196f114dc241..e69de29bb2d1 100644
--- a/arch/arm/mach-tegra/include/mach/gpio.h
+++ b/arch/arm/mach-tegra/include/mach/gpio.h
@@ -1,60 +0,0 @@
-/*
- * arch/arm/mach-tegra/include/mach/gpio.h
- *
- * Copyright (C) 2010 Google, Inc.
- *
- * Author:
- *	Erik Gilling <konkers@google.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#ifndef __MACH_TEGRA_GPIO_H
-#define __MACH_TEGRA_GPIO_H
-
-#include <linux/init.h>
-#include <mach/irqs.h>
-
-#define TEGRA_NR_GPIOS		INT_GPIO_NR
-
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value		__gpio_get_value
-#define gpio_set_value		__gpio_set_value
-#define gpio_cansleep		__gpio_cansleep
-
-#define TEGRA_GPIO_TO_IRQ(gpio) (INT_GPIO_BASE + (gpio))
-#define TEGRA_IRQ_TO_GPIO(irq) ((irq) - INT_GPIO_BASE)
-
-static inline int gpio_to_irq(unsigned int gpio)
-{
-	if (gpio < TEGRA_NR_GPIOS)
-		return INT_GPIO_BASE + gpio;
-	return -EINVAL;
-}
-
-static inline int irq_to_gpio(unsigned int irq)
-{
-	if ((irq >= INT_GPIO_BASE) && (irq < INT_GPIO_BASE + INT_GPIO_NR))
-		return irq - INT_GPIO_BASE;
-	return -EINVAL;
-}
-
-struct tegra_gpio_table {
-	int	gpio;	/* GPIO number */
-	bool	enable;	/* Enable for GPIO at init? */
-};
-
-void tegra_gpio_config(struct tegra_gpio_table *table, int num);
-void tegra_gpio_enable(int gpio);
-void tegra_gpio_disable(int gpio);
-
-#endif
diff --git a/arch/arm/mach-tegra/usb_phy.c b/arch/arm/mach-tegra/usb_phy.c
index 88081bb3ec52..37576a721aeb 100644
--- a/arch/arm/mach-tegra/usb_phy.c
+++ b/arch/arm/mach-tegra/usb_phy.c
@@ -28,6 +28,7 @@
 #include <linux/usb/otg.h>
 #include <linux/usb/ulpi.h>
 #include <asm/mach-types.h>
+#include <mach/gpio-tegra.h>
 #include <mach/usb_phy.h>
 #include <mach/iomap.h>
 
diff --git a/arch/arm/mach-u300/Kconfig b/arch/arm/mach-u300/Kconfig
index 32a7b0f7e9f7..7b5c229dc7ea 100644
--- a/arch/arm/mach-u300/Kconfig
+++ b/arch/arm/mach-u300/Kconfig
@@ -6,6 +6,7 @@ comment "ST-Ericsson Mobile Platform Products"
 
 config MACH_U300
 	bool "U300"
+	select GPIO_U300
 
 comment "ST-Ericsson U300/U330/U335/U365 Feature Selections"
 
diff --git a/arch/arm/mach-u300/core.c b/arch/arm/mach-u300/core.c
index 376b6dfdfae9..22c5ab79a74c 100644
--- a/arch/arm/mach-u300/core.c
+++ b/arch/arm/mach-u300/core.c
@@ -38,6 +38,7 @@
 #include <mach/hardware.h>
 #include <mach/syscon.h>
 #include <mach/dma_channels.h>
+#include <mach/gpio-u300.h>
 
 #include "clock.h"
 #include "mmc.h"
@@ -242,7 +243,7 @@ static struct resource gpio_resources[] = {
 		.end   = IRQ_U300_GPIO_PORT2,
 		.flags = IORESOURCE_IRQ,
 	},
-#ifdef U300_COH901571_3
+#if defined(CONFIG_MACH_U300_BS365) || defined(CONFIG_MACH_U300_BS335)
 	{
 		.name  = "gpio3",
 		.start = IRQ_U300_GPIO_PORT3,
@@ -255,6 +256,7 @@ static struct resource gpio_resources[] = {
 		.end   = IRQ_U300_GPIO_PORT4,
 		.flags = IORESOURCE_IRQ,
 	},
+#endif
 #ifdef CONFIG_MACH_U300_BS335
 	{
 		.name  = "gpio5",
@@ -269,7 +271,6 @@ static struct resource gpio_resources[] = {
 		.flags = IORESOURCE_IRQ,
 	},
 #endif /* CONFIG_MACH_U300_BS335 */
-#endif /* U300_COH901571_3 */
 };
 
 static struct resource keypad_resources[] = {
@@ -1559,11 +1560,35 @@ static struct platform_device i2c1_device = {
 	.resource = i2c1_resources,
 };
 
+/*
+ * The different variants have a few different versions of the
+ * GPIO block, with different number of ports.
+ */
+static struct u300_gpio_platform u300_gpio_plat = {
+#if defined(CONFIG_MACH_U300_BS2X) || defined(CONFIG_MACH_U300_BS330)
+	.variant = U300_GPIO_COH901335,
+	.ports = 3,
+#endif
+#ifdef CONFIG_MACH_U300_BS335
+	.variant = U300_GPIO_COH901571_3_BS335,
+	.ports = 7,
+#endif
+#ifdef CONFIG_MACH_U300_BS365
+	.variant = U300_GPIO_COH901571_3_BS365,
+	.ports = 5,
+#endif
+	.gpio_base = 0,
+	.gpio_irq_base = IRQ_U300_GPIO_BASE,
+};
+
 static struct platform_device gpio_device = {
 	.name = "u300-gpio",
 	.id = -1,
 	.num_resources = ARRAY_SIZE(gpio_resources),
 	.resource = gpio_resources,
+	.dev = {
+		.platform_data = &u300_gpio_plat,
+	},
 };
 
 static struct platform_device keypad_device = {
@@ -1669,7 +1694,7 @@ void __init u300_init_irq(void)
 	BUG_ON(IS_ERR(clk));
 	clk_enable(clk);
 
-	for (i = 0; i < NR_IRQS; i++)
+	for (i = 0; i < U300_VIC_IRQS_END; i++)
 		set_bit(i, (unsigned long *) &mask[0]);
 	vic_init((void __iomem *) U300_INTCON0_VBASE, 0, mask[0], mask[0]);
 	vic_init((void __iomem *) U300_INTCON1_VBASE, 32, mask[1], mask[1]);
diff --git a/arch/arm/mach-u300/include/mach/gpio-u300.h b/arch/arm/mach-u300/include/mach/gpio-u300.h
new file mode 100644
index 000000000000..0c2b2021951a
--- /dev/null
+++ b/arch/arm/mach-u300/include/mach/gpio-u300.h
@@ -0,0 +1,150 @@
+/*
+ * Copyright (C) 2007-2011 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ * GPIO block resgister definitions and inline macros for
+ * U300 GPIO COH 901 335 or COH 901 571/3
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ */
+
+#ifndef __MACH_U300_GPIO_U300_H
+#define __MACH_U300_GPIO_U300_H
+
+/*
+ * Individual pin assignments for the B26/S26. Notice that the
+ * actual usage of these pins depends on the PAD MUX settings, that
+ * is why the same number can potentially appear several times.
+ * In the reference design each pin is only used for one purpose.
+ * These were determined by inspecting the B26/S26 schematic:
+ * 2/1911-ROA 128 1603
+ */
+#ifdef CONFIG_MACH_U300_BS2X
+#define U300_GPIO_PIN_UART_RX		0
+#define U300_GPIO_PIN_UART_TX		1
+#define U300_GPIO_PIN_GPIO02		2  /* Unrouted */
+#define U300_GPIO_PIN_GPIO03		3  /* Unrouted */
+#define U300_GPIO_PIN_CAM_SLEEP		4
+#define U300_GPIO_PIN_CAM_REG_EN	5
+#define U300_GPIO_PIN_GPIO06		6  /* Unrouted */
+#define U300_GPIO_PIN_GPIO07		7  /* Unrouted */
+
+#define U300_GPIO_PIN_GPIO08		8  /* Service point SP2321 */
+#define U300_GPIO_PIN_GPIO09		9  /* Service point SP2322 */
+#define U300_GPIO_PIN_PHFSENSE		10 /* Headphone jack sensing */
+#define U300_GPIO_PIN_MMC_CLKRET	11 /* Clock return from MMC/SD card */
+#define U300_GPIO_PIN_MMC_CD		12 /* MMC Card insertion detection */
+#define U300_GPIO_PIN_FLIPSENSE		13 /* Mechanical flip sensing */
+#define U300_GPIO_PIN_GPIO14		14 /* DSP JTAG Port RTCK */
+#define U300_GPIO_PIN_GPIO15		15 /* Unrouted */
+
+#define U300_GPIO_PIN_GPIO16		16 /* Unrouted */
+#define U300_GPIO_PIN_GPIO17		17 /* Unrouted */
+#define U300_GPIO_PIN_GPIO18		18 /* Unrouted */
+#define U300_GPIO_PIN_GPIO19		19 /* Unrouted */
+#define U300_GPIO_PIN_GPIO20		20 /* Unrouted */
+#define U300_GPIO_PIN_GPIO21		21 /* Unrouted */
+#define U300_GPIO_PIN_GPIO22		22 /* Unrouted */
+#define U300_GPIO_PIN_GPIO23		23 /* Unrouted */
+#endif
+
+/*
+ * Individual pin assignments for the B330/S330 and B365/S365.
+ * Notice that the actual usage of these pins depends on the
+ * PAD MUX settings, that is why the same number can potentially
+ * appear several times. In the reference design each pin is only
+ * used for one purpose. These were determined by inspecting the
+ * S365 schematic.
+ */
+#if defined(CONFIG_MACH_U300_BS330) || defined(CONFIG_MACH_U300_BS365) || \
+    defined(CONFIG_MACH_U300_BS335)
+#define U300_GPIO_PIN_UART_RX		0
+#define U300_GPIO_PIN_UART_TX		1
+#define U300_GPIO_PIN_UART_CTS		2
+#define U300_GPIO_PIN_UART_RTS		3
+#define U300_GPIO_PIN_CAM_MAIN_STANDBY	4 /* Camera MAIN standby */
+#define U300_GPIO_PIN_GPIO05		5 /* Unrouted */
+#define U300_GPIO_PIN_MS_CD		6 /* Memory Stick Card insertion */
+#define U300_GPIO_PIN_GPIO07		7 /* Test point TP2430 */
+
+#define U300_GPIO_PIN_GPIO08		8 /* Test point TP2437 */
+#define U300_GPIO_PIN_GPIO09		9 /* Test point TP2431 */
+#define U300_GPIO_PIN_GPIO10		10 /* Test point TP2432 */
+#define U300_GPIO_PIN_MMC_CLKRET	11 /* Clock return from MMC/SD card */
+#define U300_GPIO_PIN_MMC_CD		12 /* MMC Card insertion detection */
+#define U300_GPIO_PIN_CAM_SUB_STANDBY	13 /* Camera SUB standby */
+#define U300_GPIO_PIN_GPIO14		14 /* Test point TP2436 */
+#define U300_GPIO_PIN_GPIO15		15 /* Unrouted */
+
+#define U300_GPIO_PIN_GPIO16		16 /* Test point TP2438 */
+#define U300_GPIO_PIN_PHFSENSE		17 /* Headphone jack sensing */
+#define U300_GPIO_PIN_GPIO18		18 /* Test point TP2439 */
+#define U300_GPIO_PIN_GPIO19		19 /* Routed somewhere */
+#define U300_GPIO_PIN_GPIO20		20 /* Unrouted */
+#define U300_GPIO_PIN_GPIO21		21 /* Unrouted */
+#define U300_GPIO_PIN_GPIO22		22 /* Unrouted */
+#define U300_GPIO_PIN_GPIO23		23 /* Unrouted */
+
+#define U300_GPIO_PIN_GPIO24		24 /* Unrouted */
+#define U300_GPIO_PIN_GPIO25		25 /* Unrouted */
+#define U300_GPIO_PIN_GPIO26		26 /* Unrouted */
+#define U300_GPIO_PIN_GPIO27		27 /* Unrouted */
+#define U300_GPIO_PIN_GPIO28		28 /* Unrouted */
+#define U300_GPIO_PIN_GPIO29		29 /* Unrouted */
+#define U300_GPIO_PIN_GPIO30		30 /* Unrouted */
+#define U300_GPIO_PIN_GPIO31		31 /* Unrouted */
+
+#define U300_GPIO_PIN_GPIO32		32 /* Unrouted */
+#define U300_GPIO_PIN_GPIO33		33 /* Unrouted */
+#define U300_GPIO_PIN_GPIO34		34 /* Unrouted */
+#define U300_GPIO_PIN_GPIO35		35 /* Unrouted */
+#define U300_GPIO_PIN_GPIO36		36 /* Unrouted */
+#define U300_GPIO_PIN_GPIO37		37 /* Unrouted */
+#define U300_GPIO_PIN_GPIO38		38 /* Unrouted */
+#define U300_GPIO_PIN_GPIO39		39 /* Unrouted */
+
+#ifdef CONFIG_MACH_U300_BS335
+
+#define U300_GPIO_PIN_GPIO40		40 /* Unrouted */
+#define U300_GPIO_PIN_GPIO41		41 /* Unrouted */
+#define U300_GPIO_PIN_GPIO42		42 /* Unrouted */
+#define U300_GPIO_PIN_GPIO43		43 /* Unrouted */
+#define U300_GPIO_PIN_GPIO44		44 /* Unrouted */
+#define U300_GPIO_PIN_GPIO45		45 /* Unrouted */
+#define U300_GPIO_PIN_GPIO46		46 /* Unrouted */
+#define U300_GPIO_PIN_GPIO47		47 /* Unrouted */
+
+#define U300_GPIO_PIN_GPIO48		48 /* Unrouted */
+#define U300_GPIO_PIN_GPIO49		49 /* Unrouted */
+#define U300_GPIO_PIN_GPIO50		50 /* Unrouted */
+#define U300_GPIO_PIN_GPIO51		51 /* Unrouted */
+#define U300_GPIO_PIN_GPIO52		52 /* Unrouted */
+#define U300_GPIO_PIN_GPIO53		53 /* Unrouted */
+#define U300_GPIO_PIN_GPIO54		54 /* Unrouted */
+#define U300_GPIO_PIN_GPIO55		55 /* Unrouted */
+#endif
+
+#endif
+
+/**
+ * enum u300_gpio_variant - the type of U300 GPIO employed
+ */
+enum u300_gpio_variant {
+	U300_GPIO_COH901335,
+	U300_GPIO_COH901571_3_BS335,
+	U300_GPIO_COH901571_3_BS365,
+};
+
+/**
+ * struct u300_gpio_platform - U300 GPIO platform data
+ * @variant: IP block variant
+ * @ports: number of GPIO block ports
+ * @gpio_base: first GPIO number for this block (use a free range)
+ * @gpio_irq_base: first GPIO IRQ number for this block (use a free range)
+ */
+struct u300_gpio_platform {
+	enum u300_gpio_variant variant;
+	u8 ports;
+	int gpio_base;
+	int gpio_irq_base;
+};
+
+#endif /* __MACH_U300_GPIO_U300_H */
diff --git a/arch/arm/mach-u300/include/mach/gpio.h b/arch/arm/mach-u300/include/mach/gpio.h
index d5a71abcbaea..e69de29bb2d1 100644
--- a/arch/arm/mach-u300/include/mach/gpio.h
+++ b/arch/arm/mach-u300/include/mach/gpio.h
@@ -1,294 +0,0 @@
-/*
- *
- * arch/arm/mach-u300/include/mach/gpio.h
- *
- *
- * Copyright (C) 2007-2009 ST-Ericsson AB
- * License terms: GNU General Public License (GPL) version 2
- * GPIO block resgister definitions and inline macros for
- * U300 GPIO COH 901 335 or COH 901 571/3
- * Author: Linus Walleij <linus.walleij@stericsson.com>
- */
-
-#ifndef __MACH_U300_GPIO_H
-#define __MACH_U300_GPIO_H
-
-#include <linux/kernel.h>
-#include <linux/io.h>
-#include <mach/hardware.h>
-#include <asm/irq.h>
-
-/* Switch type depending on platform/chip variant */
-#if defined(CONFIG_MACH_U300_BS2X) || defined(CONFIG_MACH_U300_BS330)
-#define U300_COH901335
-#endif
-#if defined(CONFIG_MACH_U300_BS365) || defined(CONFIG_MACH_U300_BS335)
-#define U300_COH901571_3
-#endif
-
-/* Get base address for regs here */
-#include "u300-regs.h"
-/* IRQ numbers */
-#include "irqs.h"
-
-/*
- * This is the GPIO block definitions. GPIO (General Purpose I/O) can be
- * used for anything, and often is. The event/enable etc figures are for
- * the lowermost pin (pin 0 on each port), shift this left to match your
- * pin if you're gonna use these values.
- */
-#ifdef U300_COH901335
-#define U300_GPIO_PORTX_SPACING				(0x1C)
-/* Port X Pin Data Register 32bit, this is both input and output (R/W) */
-#define U300_GPIO_PXPDIR				(0x00)
-#define U300_GPIO_PXPDOR				(0x00)
-/* Port X Pin Config Register 32bit (R/W) */
-#define U300_GPIO_PXPCR					(0x04)
-#define U300_GPIO_PXPCR_ALL_PINS_MODE_MASK		(0x0000FFFFUL)
-#define U300_GPIO_PXPCR_PIN_MODE_MASK			(0x00000003UL)
-#define U300_GPIO_PXPCR_PIN_MODE_SHIFT			(0x00000002UL)
-#define U300_GPIO_PXPCR_PIN_MODE_INPUT			(0x00000000UL)
-#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL	(0x00000001UL)
-#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN	(0x00000002UL)
-#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE	(0x00000003UL)
-/* Port X Interrupt Event Register 32bit (R/W) */
-#define U300_GPIO_PXIEV					(0x08)
-#define U300_GPIO_PXIEV_ALL_IRQ_EVENT_MASK		(0x000000FFUL)
-#define U300_GPIO_PXIEV_IRQ_EVENT			(0x00000001UL)
-/* Port X Interrupt Enable Register 32bit (R/W) */
-#define U300_GPIO_PXIEN					(0x0C)
-#define U300_GPIO_PXIEN_ALL_IRQ_ENABLE_MASK		(0x000000FFUL)
-#define U300_GPIO_PXIEN_IRQ_ENABLE			(0x00000001UL)
-/* Port X Interrupt Force Register 32bit (R/W) */
-#define U300_GPIO_PXIFR					(0x10)
-#define U300_GPIO_PXIFR_ALL_IRQ_FORCE_MASK		(0x000000FFUL)
-#define U300_GPIO_PXIFR_IRQ_FORCE			(0x00000001UL)
-/* Port X Interrupt Config Register 32bit (R/W) */
-#define U300_GPIO_PXICR					(0x14)
-#define U300_GPIO_PXICR_ALL_IRQ_CONFIG_MASK		(0x000000FFUL)
-#define U300_GPIO_PXICR_IRQ_CONFIG_MASK			(0x00000001UL)
-#define U300_GPIO_PXICR_IRQ_CONFIG_FALLING_EDGE		(0x00000000UL)
-#define U300_GPIO_PXICR_IRQ_CONFIG_RISING_EDGE		(0x00000001UL)
-/* Port X Pull-up Enable Register 32bit (R/W) */
-#define U300_GPIO_PXPER					(0x18)
-#define U300_GPIO_PXPER_ALL_PULL_UP_DISABLE_MASK	(0x000000FFUL)
-#define U300_GPIO_PXPER_PULL_UP_DISABLE			(0x00000001UL)
-/* Control Register 32bit (R/W) */
-#define U300_GPIO_CR					(0x54)
-#define U300_GPIO_CR_BLOCK_CLOCK_ENABLE			(0x00000001UL)
-/* three ports of 8 bits each = GPIO pins 0..23 */
-#define U300_GPIO_NUM_PORTS 3
-#define U300_GPIO_PINS_PER_PORT 8
-#define U300_GPIO_MAX	(U300_GPIO_PINS_PER_PORT * U300_GPIO_NUM_PORTS - 1)
-#endif
-
-#ifdef U300_COH901571_3
-/*
- * Control Register 32bit (R/W)
- * bit 15-9 (mask 0x0000FE00) contains the number of cores. 8*cores
- * gives the number of GPIO pins.
- * bit 8-2  (mask 0x000001FC) contains the core version ID.
- */
-#define U300_GPIO_CR					(0x00)
-#define U300_GPIO_CR_SYNC_SEL_ENABLE			(0x00000002UL)
-#define U300_GPIO_CR_BLOCK_CLKRQ_ENABLE			(0x00000001UL)
-#define U300_GPIO_PORTX_SPACING				(0x30)
-/* Port X Pin Data INPUT Register 32bit (R/W) */
-#define U300_GPIO_PXPDIR				(0x04)
-/* Port X Pin Data OUTPUT Register 32bit (R/W) */
-#define U300_GPIO_PXPDOR				(0x08)
-/* Port X Pin Config Register 32bit (R/W) */
-#define U300_GPIO_PXPCR					(0x0C)
-#define U300_GPIO_PXPCR_ALL_PINS_MODE_MASK		(0x0000FFFFUL)
-#define U300_GPIO_PXPCR_PIN_MODE_MASK			(0x00000003UL)
-#define U300_GPIO_PXPCR_PIN_MODE_SHIFT			(0x00000002UL)
-#define U300_GPIO_PXPCR_PIN_MODE_INPUT			(0x00000000UL)
-#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL	(0x00000001UL)
-#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN	(0x00000002UL)
-#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE	(0x00000003UL)
-/* Port X Pull-up Enable Register 32bit (R/W) */
-#define U300_GPIO_PXPER					(0x10)
-#define U300_GPIO_PXPER_ALL_PULL_UP_DISABLE_MASK	(0x000000FFUL)
-#define U300_GPIO_PXPER_PULL_UP_DISABLE			(0x00000001UL)
-/* Port X Interrupt Event Register 32bit (R/W) */
-#define U300_GPIO_PXIEV					(0x14)
-#define U300_GPIO_PXIEV_ALL_IRQ_EVENT_MASK		(0x000000FFUL)
-#define U300_GPIO_PXIEV_IRQ_EVENT			(0x00000001UL)
-/* Port X Interrupt Enable Register 32bit (R/W) */
-#define U300_GPIO_PXIEN					(0x18)
-#define U300_GPIO_PXIEN_ALL_IRQ_ENABLE_MASK		(0x000000FFUL)
-#define U300_GPIO_PXIEN_IRQ_ENABLE			(0x00000001UL)
-/* Port X Interrupt Force Register 32bit (R/W) */
-#define U300_GPIO_PXIFR					(0x1C)
-#define U300_GPIO_PXIFR_ALL_IRQ_FORCE_MASK		(0x000000FFUL)
-#define U300_GPIO_PXIFR_IRQ_FORCE			(0x00000001UL)
-/* Port X Interrupt Config Register 32bit (R/W) */
-#define U300_GPIO_PXICR					(0x20)
-#define U300_GPIO_PXICR_ALL_IRQ_CONFIG_MASK		(0x000000FFUL)
-#define U300_GPIO_PXICR_IRQ_CONFIG_MASK			(0x00000001UL)
-#define U300_GPIO_PXICR_IRQ_CONFIG_FALLING_EDGE		(0x00000000UL)
-#define U300_GPIO_PXICR_IRQ_CONFIG_RISING_EDGE		(0x00000001UL)
-#ifdef CONFIG_MACH_U300_BS335
-/* seven ports of 8 bits each = GPIO pins 0..55 */
-#define U300_GPIO_NUM_PORTS 7
-#else
-/* five ports of 8 bits each = GPIO pins 0..39 */
-#define U300_GPIO_NUM_PORTS 5
-#endif
-#define U300_GPIO_PINS_PER_PORT 8
-#define U300_GPIO_MAX (U300_GPIO_PINS_PER_PORT * U300_GPIO_NUM_PORTS - 1)
-#endif
-
-/*
- * Individual pin assignments for the B26/S26. Notice that the
- * actual usage of these pins depends on the PAD MUX settings, that
- * is why the same number can potentially appear several times.
- * In the reference design each pin is only used for one purpose.
- * These were determined by inspecting the B26/S26 schematic:
- * 2/1911-ROA 128 1603
- */
-#ifdef CONFIG_MACH_U300_BS2X
-#define U300_GPIO_PIN_UART_RX		0
-#define U300_GPIO_PIN_UART_TX		1
-#define U300_GPIO_PIN_GPIO02		2  /* Unrouted */
-#define U300_GPIO_PIN_GPIO03		3  /* Unrouted */
-#define U300_GPIO_PIN_CAM_SLEEP		4
-#define U300_GPIO_PIN_CAM_REG_EN	5
-#define U300_GPIO_PIN_GPIO06		6  /* Unrouted */
-#define U300_GPIO_PIN_GPIO07		7  /* Unrouted */
-
-#define U300_GPIO_PIN_GPIO08		8  /* Service point SP2321 */
-#define U300_GPIO_PIN_GPIO09		9  /* Service point SP2322 */
-#define U300_GPIO_PIN_PHFSENSE		10 /* Headphone jack sensing */
-#define U300_GPIO_PIN_MMC_CLKRET	11 /* Clock return from MMC/SD card */
-#define U300_GPIO_PIN_MMC_CD		12 /* MMC Card insertion detection */
-#define U300_GPIO_PIN_FLIPSENSE		13 /* Mechanical flip sensing */
-#define U300_GPIO_PIN_GPIO14		14 /* DSP JTAG Port RTCK */
-#define U300_GPIO_PIN_GPIO15		15 /* Unrouted */
-
-#define U300_GPIO_PIN_GPIO16		16 /* Unrouted */
-#define U300_GPIO_PIN_GPIO17		17 /* Unrouted */
-#define U300_GPIO_PIN_GPIO18		18 /* Unrouted */
-#define U300_GPIO_PIN_GPIO19		19 /* Unrouted */
-#define U300_GPIO_PIN_GPIO20		20 /* Unrouted */
-#define U300_GPIO_PIN_GPIO21		21 /* Unrouted */
-#define U300_GPIO_PIN_GPIO22		22 /* Unrouted */
-#define U300_GPIO_PIN_GPIO23		23 /* Unrouted */
-#endif
-
-/*
- * Individual pin assignments for the B330/S330 and B365/S365.
- * Notice that the actual usage of these pins depends on the
- * PAD MUX settings, that is why the same number can potentially
- * appear several times. In the reference design each pin is only
- * used for one purpose. These were determined by inspecting the
- * S365 schematic.
- */
-#if defined(CONFIG_MACH_U300_BS330) || defined(CONFIG_MACH_U300_BS365) || \
-    defined(CONFIG_MACH_U300_BS335)
-#define U300_GPIO_PIN_UART_RX		0
-#define U300_GPIO_PIN_UART_TX		1
-#define U300_GPIO_PIN_UART_CTS		2
-#define U300_GPIO_PIN_UART_RTS		3
-#define U300_GPIO_PIN_CAM_MAIN_STANDBY	4 /* Camera MAIN standby */
-#define U300_GPIO_PIN_GPIO05		5 /* Unrouted */
-#define U300_GPIO_PIN_MS_CD		6 /* Memory Stick Card insertion */
-#define U300_GPIO_PIN_GPIO07		7 /* Test point TP2430 */
-
-#define U300_GPIO_PIN_GPIO08		8 /* Test point TP2437 */
-#define U300_GPIO_PIN_GPIO09		9 /* Test point TP2431 */
-#define U300_GPIO_PIN_GPIO10		10 /* Test point TP2432 */
-#define U300_GPIO_PIN_MMC_CLKRET	11 /* Clock return from MMC/SD card */
-#define U300_GPIO_PIN_MMC_CD		12 /* MMC Card insertion detection */
-#define U300_GPIO_PIN_CAM_SUB_STANDBY	13 /* Camera SUB standby */
-#define U300_GPIO_PIN_GPIO14		14 /* Test point TP2436 */
-#define U300_GPIO_PIN_GPIO15		15 /* Unrouted */
-
-#define U300_GPIO_PIN_GPIO16		16 /* Test point TP2438 */
-#define U300_GPIO_PIN_PHFSENSE		17 /* Headphone jack sensing */
-#define U300_GPIO_PIN_GPIO18		18 /* Test point TP2439 */
-#define U300_GPIO_PIN_GPIO19		19 /* Routed somewhere */
-#define U300_GPIO_PIN_GPIO20		20 /* Unrouted */
-#define U300_GPIO_PIN_GPIO21		21 /* Unrouted */
-#define U300_GPIO_PIN_GPIO22		22 /* Unrouted */
-#define U300_GPIO_PIN_GPIO23		23 /* Unrouted */
-
-#define U300_GPIO_PIN_GPIO24		24 /* Unrouted */
-#define U300_GPIO_PIN_GPIO25		25 /* Unrouted */
-#define U300_GPIO_PIN_GPIO26		26 /* Unrouted */
-#define U300_GPIO_PIN_GPIO27		27 /* Unrouted */
-#define U300_GPIO_PIN_GPIO28		28 /* Unrouted */
-#define U300_GPIO_PIN_GPIO29		29 /* Unrouted */
-#define U300_GPIO_PIN_GPIO30		30 /* Unrouted */
-#define U300_GPIO_PIN_GPIO31		31 /* Unrouted */
-
-#define U300_GPIO_PIN_GPIO32		32 /* Unrouted */
-#define U300_GPIO_PIN_GPIO33		33 /* Unrouted */
-#define U300_GPIO_PIN_GPIO34		34 /* Unrouted */
-#define U300_GPIO_PIN_GPIO35		35 /* Unrouted */
-#define U300_GPIO_PIN_GPIO36		36 /* Unrouted */
-#define U300_GPIO_PIN_GPIO37		37 /* Unrouted */
-#define U300_GPIO_PIN_GPIO38		38 /* Unrouted */
-#define U300_GPIO_PIN_GPIO39		39 /* Unrouted */
-
-#ifdef CONFIG_MACH_U300_BS335
-
-#define U300_GPIO_PIN_GPIO40		40 /* Unrouted */
-#define U300_GPIO_PIN_GPIO41		41 /* Unrouted */
-#define U300_GPIO_PIN_GPIO42		42 /* Unrouted */
-#define U300_GPIO_PIN_GPIO43		43 /* Unrouted */
-#define U300_GPIO_PIN_GPIO44		44 /* Unrouted */
-#define U300_GPIO_PIN_GPIO45		45 /* Unrouted */
-#define U300_GPIO_PIN_GPIO46		46 /* Unrouted */
-#define U300_GPIO_PIN_GPIO47		47 /* Unrouted */
-
-#define U300_GPIO_PIN_GPIO48		48 /* Unrouted */
-#define U300_GPIO_PIN_GPIO49		49 /* Unrouted */
-#define U300_GPIO_PIN_GPIO50		50 /* Unrouted */
-#define U300_GPIO_PIN_GPIO51		51 /* Unrouted */
-#define U300_GPIO_PIN_GPIO52		52 /* Unrouted */
-#define U300_GPIO_PIN_GPIO53		53 /* Unrouted */
-#define U300_GPIO_PIN_GPIO54		54 /* Unrouted */
-#define U300_GPIO_PIN_GPIO55		55 /* Unrouted */
-#endif
-
-#endif
-
-/* translates a pin number to a port number */
-#define PIN_TO_PORT(val) (val >> 3)
-
-/* These can be found in arch/arm/mach-u300/gpio.c */
-extern int gpio_is_valid(int number);
-extern int gpio_request(unsigned gpio, const char *label);
-extern void gpio_free(unsigned gpio);
-extern int gpio_direction_input(unsigned gpio);
-extern int gpio_direction_output(unsigned gpio, int value);
-extern int gpio_register_callback(unsigned gpio,
-				  int (*func)(void *arg),
-				  void *);
-extern int gpio_unregister_callback(unsigned gpio);
-extern void enable_irq_on_gpio_pin(unsigned gpio, int edge);
-extern void disable_irq_on_gpio_pin(unsigned gpio);
-extern void gpio_pullup(unsigned gpio, int value);
-extern int gpio_get_value(unsigned gpio);
-extern void gpio_set_value(unsigned gpio, int value);
-
-#define gpio_get_value_cansleep gpio_get_value
-#define gpio_set_value_cansleep gpio_set_value
-
-/* wrappers to sleep-enable the previous two functions */
-static inline unsigned gpio_to_irq(unsigned gpio)
-{
-	return PIN_TO_PORT(gpio) + IRQ_U300_GPIO_PORT0;
-}
-
-static inline unsigned irq_to_gpio(unsigned irq)
-{
-	/*
-	 * FIXME: This is no 1-1 mapping at all, it points to the
-	 * whole block of 8 pins.
-	 */
-	return (irq - IRQ_U300_GPIO_PORT0) << 3;
-}
-
-#endif
diff --git a/arch/arm/mach-u300/include/mach/irqs.h b/arch/arm/mach-u300/include/mach/irqs.h
index 09b1b28fa8fd..d270fea32926 100644
--- a/arch/arm/mach-u300/include/mach/irqs.h
+++ b/arch/arm/mach-u300/include/mach/irqs.h
@@ -72,7 +72,7 @@
 
 /* DB3150 and DB3200 have only 45 IRQs */
 #if defined(CONFIG_MACH_U300_BS2X) || defined(CONFIG_MACH_U300_BS330)
-#define U300_NR_IRQS			45
+#define U300_VIC_IRQS_END		45
 #endif
 
 /* The DB3350-specific interrupt lines */
@@ -88,7 +88,7 @@
 #define IRQ_U300_GPIO_PORT4		53
 #define IRQ_U300_GPIO_PORT5		54
 #define IRQ_U300_GPIO_PORT6		55
-#define U300_NR_IRQS			56
+#define U300_VIC_IRQS_END		56
 #endif
 
 /* The DB3210-specific interrupt lines */
@@ -106,16 +106,25 @@
 #define IRQ_U300_NFIF			45
 #define IRQ_U300_NFIF2			46
 #define IRQ_U300_SYSCON_PLL_LOCK	47
-#define U300_NR_IRQS			48
+#define U300_VIC_IRQS_END		48
 #endif
 
-#ifdef CONFIG_AB3550_CORE
-#define IRQ_AB3550_BASE			(U300_NR_IRQS)
-#define IRQ_AB3550_END			(IRQ_AB3550_BASE + 37)
+/* Maximum 8*7 GPIO lines */
+#ifdef CONFIG_GPIO_U300
+#define IRQ_U300_GPIO_BASE		(U300_VIC_IRQS_END)
+#define IRQ_U300_GPIO_END		(IRQ_U300_GPIO_BASE + 56)
+#else
+#define IRQ_U300_GPIO_END		(U300_VIC_IRQS_END)
+#endif
 
-#define NR_IRQS				(IRQ_AB3550_END + 1)
+/* Optional AB3550 mixsig chip */
+#ifdef CONFIG_AB3550_CORE
+#define IRQ_AB3550_BASE			(IRQ_U300_GPIO_END)
+#define IRQ_AB3550_END			(IRQ_AB3550_BASE + 38)
 #else
-#define NR_IRQS U300_NR_IRQS
+#define IRQ_AB3550_END			(IRQ_U300_GPIO_END)
 #endif
 
+#define NR_IRQS				(IRQ_AB3550_END)
+
 #endif
diff --git a/arch/arm/mach-u300/mmc.c b/arch/arm/mach-u300/mmc.c
index 677ccef5cd32..d9a5c92db74a 100644
--- a/arch/arm/mach-u300/mmc.c
+++ b/arch/arm/mach-u300/mmc.c
@@ -13,12 +13,12 @@
 #include <linux/device.h>
 #include <linux/amba/bus.h>
 #include <linux/mmc/host.h>
-#include <linux/gpio.h>
 #include <linux/dmaengine.h>
 #include <linux/amba/mmci.h>
 #include <linux/slab.h>
 #include <mach/coh901318.h>
 #include <mach/dma_channels.h>
+#include <mach/gpio-u300.h>
 
 #include "mmc.h"
 #include "padmux.h"
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index f26fd76f72b4..15b23e4bd488 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -6,10 +6,10 @@
 
 #include <linux/kernel.h>
 #include <linux/init.h>
-#include <linux/gpio.h>
 
 #include <asm/mach-types.h>
 #include <plat/pincfg.h>
+#include <plat/gpio-nomadik.h>
 #include <mach/hardware.h>
 
 #include "pins-db8500.h"
diff --git a/arch/arm/mach-ux500/board-mop500-u8500uib.c b/arch/arm/mach-ux500/board-mop500-u8500uib.c
index 8ce46c0fdfd5..feb5744d98b7 100644
--- a/arch/arm/mach-ux500/board-mop500-u8500uib.c
+++ b/arch/arm/mach-ux500/board-mop500-u8500uib.c
@@ -4,7 +4,7 @@
  * Board data for the U8500 UIB, also known as the New UIB
  * License terms: GNU General Public License (GPL), version 2
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/i2c.h>
@@ -13,7 +13,6 @@
 #include <linux/mfd/tc3589x.h>
 #include <linux/input/matrix_keypad.h>
 
-#include <mach/gpio.h>
 #include <mach/irqs.h>
 
 #include "board-mop500.h"
diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c
index 2cc4876db212..f67b83dd9010 100644
--- a/arch/arm/mach-ux500/board-mop500.c
+++ b/arch/arm/mach-ux500/board-mop500.c
@@ -37,6 +37,7 @@
 #include <plat/i2c.h>
 #include <plat/ste_dma40.h>
 #include <plat/pincfg.h>
+#include <plat/gpio-nomadik.h>
 
 #include <mach/hardware.h>
 #include <mach/setup.h>
diff --git a/arch/arm/mach-ux500/board-u5500-sdi.c b/arch/arm/mach-ux500/board-u5500-sdi.c
index 739fb4c5b160..63c3f8058ffc 100644
--- a/arch/arm/mach-ux500/board-u5500-sdi.c
+++ b/arch/arm/mach-ux500/board-u5500-sdi.c
@@ -7,9 +7,9 @@
 
 #include <linux/amba/mmci.h>
 #include <linux/mmc/host.h>
-#include <linux/gpio.h>
 
 #include <plat/pincfg.h>
+#include <plat/gpio-nomadik.h>
 #include <mach/db5500-regs.h>
 #include <plat/ste_dma40.h>
 
diff --git a/arch/arm/mach-ux500/board-u5500.c b/arch/arm/mach-ux500/board-u5500.c
index 166d47a5f4f3..e014aa749b03 100644
--- a/arch/arm/mach-ux500/board-u5500.c
+++ b/arch/arm/mach-ux500/board-u5500.c
@@ -8,7 +8,6 @@
 #include <linux/init.h>
 #include <linux/platform_device.h>
 #include <linux/amba/bus.h>
-#include <linux/gpio.h>
 #include <linux/irq.h>
 #include <linux/i2c.h>
 
@@ -17,6 +16,7 @@
 
 #include <plat/pincfg.h>
 #include <plat/i2c.h>
+#include <plat/gpio-nomadik.h>
 
 #include <mach/hardware.h>
 #include <mach/devices.h>
diff --git a/arch/arm/mach-ux500/cpu-db5500.c b/arch/arm/mach-ux500/cpu-db5500.c
index 22705d246fc7..9de1af008094 100644
--- a/arch/arm/mach-ux500/cpu-db5500.c
+++ b/arch/arm/mach-ux500/cpu-db5500.c
@@ -13,7 +13,7 @@
 #include <asm/mach/map.h>
 #include <asm/pmu.h>
 
-#include <plat/gpio.h>
+#include <plat/gpio-nomadik.h>
 
 #include <mach/hardware.h>
 #include <mach/devices.h>
diff --git a/arch/arm/mach-ux500/cpu-db8500.c b/arch/arm/mach-ux500/cpu-db8500.c
index 4598b06c8c55..13e8890a8b8a 100644
--- a/arch/arm/mach-ux500/cpu-db8500.c
+++ b/arch/arm/mach-ux500/cpu-db8500.c
@@ -14,12 +14,12 @@
 #include <linux/amba/bus.h>
 #include <linux/interrupt.h>
 #include <linux/irq.h>
-#include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
 
 #include <asm/mach/map.h>
 #include <asm/pmu.h>
+#include <plat/gpio-nomadik.h>
 #include <mach/hardware.h>
 #include <mach/setup.h>
 #include <mach/devices.h>
diff --git a/arch/arm/mach-ux500/devices-common.c b/arch/arm/mach-ux500/devices-common.c
index 13a4ce046ae5..c563e5418d80 100644
--- a/arch/arm/mach-ux500/devices-common.c
+++ b/arch/arm/mach-ux500/devices-common.c
@@ -13,7 +13,7 @@
 #include <linux/platform_device.h>
 #include <linux/amba/bus.h>
 
-#include <plat/gpio.h>
+#include <plat/gpio-nomadik.h>
 
 #include <mach/hardware.h>
 
diff --git a/arch/arm/mach-ux500/include/mach/gpio.h b/arch/arm/mach-ux500/include/mach/gpio.h
index 3c4cd31ad9f7..7389df911b1a 100644
--- a/arch/arm/mach-ux500/include/mach/gpio.h
+++ b/arch/arm/mach-ux500/include/mach/gpio.h
@@ -7,6 +7,4 @@
  */
 #define ARCH_NR_GPIOS	350
 
-#include <plat/gpio.h>
-
 #endif /* __ASM_ARCH_GPIO_H */
diff --git a/arch/arm/mach-versatile/include/mach/gpio.h b/arch/arm/mach-versatile/include/mach/gpio.h
index 94ff27678a46..40a8c178f10d 100644
--- a/arch/arm/mach-versatile/include/mach/gpio.h
+++ b/arch/arm/mach-versatile/include/mach/gpio.h
@@ -1,6 +1 @@
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value	__gpio_get_value
-#define gpio_set_value	__gpio_set_value
-#define gpio_cansleep	__gpio_cansleep
-#define gpio_to_irq	__gpio_to_irq
+/* empty */
diff --git a/arch/arm/mach-vexpress/include/mach/io.h b/arch/arm/mach-vexpress/include/mach/io.h
index 748bb524ee71..13522d86685e 100644
--- a/arch/arm/mach-vexpress/include/mach/io.h
+++ b/arch/arm/mach-vexpress/include/mach/io.h
@@ -20,8 +20,6 @@
 #ifndef __ASM_ARM_ARCH_IO_H
 #define __ASM_ARM_ARCH_IO_H
 
-#define IO_SPACE_LIMIT 0xffffffff
-
 #define __io(a)		__typesafe_io(a)
 #define __mem_pci(a)	(a)
 
diff --git a/arch/arm/mach-vt8500/include/mach/gpio.h b/arch/arm/mach-vt8500/include/mach/gpio.h
index 94ff27678a46..40a8c178f10d 100644
--- a/arch/arm/mach-vt8500/include/mach/gpio.h
+++ b/arch/arm/mach-vt8500/include/mach/gpio.h
@@ -1,6 +1 @@
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value	__gpio_get_value
-#define gpio_set_value	__gpio_set_value
-#define gpio_cansleep	__gpio_cansleep
-#define gpio_to_irq	__gpio_to_irq
+/* empty */
diff --git a/arch/arm/mach-vt8500/include/mach/io.h b/arch/arm/mach-vt8500/include/mach/io.h
index 9077239f78c9..46181eecf273 100644
--- a/arch/arm/mach-vt8500/include/mach/io.h
+++ b/arch/arm/mach-vt8500/include/mach/io.h
@@ -20,8 +20,6 @@
 #ifndef __ASM_ARM_ARCH_IO_H
 #define __ASM_ARM_ARCH_IO_H
 
-#define IO_SPACE_LIMIT 0xffff
-
 #define __io(a)		__typesafe_io((a) + 0xf0000000)
 #define __mem_pci(a)	(a)
 
diff --git a/arch/arm/mach-w90x900/include/mach/gpio.h b/arch/arm/mach-w90x900/include/mach/gpio.h
index 034da3e390c9..5385a4203277 100644
--- a/arch/arm/mach-w90x900/include/mach/gpio.h
+++ b/arch/arm/mach-w90x900/include/mach/gpio.h
@@ -15,16 +15,12 @@
 
 #include <mach/hardware.h>
 #include <asm/irq.h>
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value	__gpio_get_value
-#define gpio_set_value	__gpio_set_value
-#define gpio_cansleep	__gpio_cansleep
 
 static inline int gpio_to_irq(unsigned gpio)
 {
 	return gpio;
 }
+#define gpio_to_irq gpio_to_irq
 
 static inline int irq_to_gpio(unsigned irq)
 {
diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig
index 88633fe01a5d..7d5fff7b3632 100644
--- a/arch/arm/mm/Kconfig
+++ b/arch/arm/mm/Kconfig
@@ -822,7 +822,7 @@ config CACHE_L2X0
 		   REALVIEW_EB_A9MP || SOC_IMX35 || SOC_IMX31 || MACH_REALVIEW_PBX || \
 		   ARCH_NOMADIK || ARCH_OMAP4 || ARCH_EXYNOS4 || ARCH_TEGRA || \
 		   ARCH_U8500 || ARCH_VEXPRESS_CA9X4 || ARCH_SHMOBILE || \
-		   ARCH_PRIMA2 || ARCH_ZYNQ || ARCH_CNS3XXX
+		   ARCH_PRIMA2 || ARCH_ZYNQ || ARCH_CNS3XXX || ARCH_HIGHBANK
 	default y
 	select OUTER_CACHE
 	select OUTER_CACHE_SYNC
diff --git a/arch/arm/mm/cache-l2x0.c b/arch/arm/mm/cache-l2x0.c
index 9ecfdb511951..3f9b9980478e 100644
--- a/arch/arm/mm/cache-l2x0.c
+++ b/arch/arm/mm/cache-l2x0.c
@@ -16,9 +16,12 @@
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
  */
+#include <linux/err.h>
 #include <linux/init.h>
 #include <linux/spinlock.h>
 #include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
 
 #include <asm/cacheflush.h>
 #include <asm/hardware/cache-l2x0.h>
@@ -30,11 +33,19 @@ static DEFINE_SPINLOCK(l2x0_lock);
 static uint32_t l2x0_way_mask;	/* Bitmask of active ways */
 static uint32_t l2x0_size;
 
+struct l2x0_regs l2x0_saved_regs;
+
+struct l2x0_of_data {
+	void (*setup)(const struct device_node *, __u32 *, __u32 *);
+	void (*save)(void);
+	void (*resume)(void);
+};
+
 static inline void cache_wait_way(void __iomem *reg, unsigned long mask)
 {
 	/* wait for cache operation by line or way to complete */
 	while (readl_relaxed(reg) & mask)
-		;
+		cpu_relax();
 }
 
 #ifdef CONFIG_CACHE_PL310
@@ -277,7 +288,7 @@ static void l2x0_disable(void)
 	spin_unlock_irqrestore(&l2x0_lock, flags);
 }
 
-static void __init l2x0_unlock(__u32 cache_id)
+static void l2x0_unlock(__u32 cache_id)
 {
 	int lockregs;
 	int i;
@@ -353,6 +364,8 @@ void __init l2x0_init(void __iomem *base, __u32 aux_val, __u32 aux_mask)
 		/* l2x0 controller is disabled */
 		writel_relaxed(aux, l2x0_base + L2X0_AUX_CTRL);
 
+		l2x0_saved_regs.aux_ctrl = aux;
+
 		l2x0_inv_all();
 
 		/* enable L2X0 */
@@ -372,3 +385,202 @@ void __init l2x0_init(void __iomem *base, __u32 aux_val, __u32 aux_mask)
 	printk(KERN_INFO "l2x0: %d ways, CACHE_ID 0x%08x, AUX_CTRL 0x%08x, Cache size: %d B\n",
 			ways, cache_id, aux, l2x0_size);
 }
+
+#ifdef CONFIG_OF
+static void __init l2x0_of_setup(const struct device_node *np,
+				 __u32 *aux_val, __u32 *aux_mask)
+{
+	u32 data[2] = { 0, 0 };
+	u32 tag = 0;
+	u32 dirty = 0;
+	u32 val = 0, mask = 0;
+
+	of_property_read_u32(np, "arm,tag-latency", &tag);
+	if (tag) {
+		mask |= L2X0_AUX_CTRL_TAG_LATENCY_MASK;
+		val |= (tag - 1) << L2X0_AUX_CTRL_TAG_LATENCY_SHIFT;
+	}
+
+	of_property_read_u32_array(np, "arm,data-latency",
+				   data, ARRAY_SIZE(data));
+	if (data[0] && data[1]) {
+		mask |= L2X0_AUX_CTRL_DATA_RD_LATENCY_MASK |
+			L2X0_AUX_CTRL_DATA_WR_LATENCY_MASK;
+		val |= ((data[0] - 1) << L2X0_AUX_CTRL_DATA_RD_LATENCY_SHIFT) |
+		       ((data[1] - 1) << L2X0_AUX_CTRL_DATA_WR_LATENCY_SHIFT);
+	}
+
+	of_property_read_u32(np, "arm,dirty-latency", &dirty);
+	if (dirty) {
+		mask |= L2X0_AUX_CTRL_DIRTY_LATENCY_MASK;
+		val |= (dirty - 1) << L2X0_AUX_CTRL_DIRTY_LATENCY_SHIFT;
+	}
+
+	*aux_val &= ~mask;
+	*aux_val |= val;
+	*aux_mask &= ~mask;
+}
+
+static void __init pl310_of_setup(const struct device_node *np,
+				  __u32 *aux_val, __u32 *aux_mask)
+{
+	u32 data[3] = { 0, 0, 0 };
+	u32 tag[3] = { 0, 0, 0 };
+	u32 filter[2] = { 0, 0 };
+
+	of_property_read_u32_array(np, "arm,tag-latency", tag, ARRAY_SIZE(tag));
+	if (tag[0] && tag[1] && tag[2])
+		writel_relaxed(
+			((tag[0] - 1) << L2X0_LATENCY_CTRL_RD_SHIFT) |
+			((tag[1] - 1) << L2X0_LATENCY_CTRL_WR_SHIFT) |
+			((tag[2] - 1) << L2X0_LATENCY_CTRL_SETUP_SHIFT),
+			l2x0_base + L2X0_TAG_LATENCY_CTRL);
+
+	of_property_read_u32_array(np, "arm,data-latency",
+				   data, ARRAY_SIZE(data));
+	if (data[0] && data[1] && data[2])
+		writel_relaxed(
+			((data[0] - 1) << L2X0_LATENCY_CTRL_RD_SHIFT) |
+			((data[1] - 1) << L2X0_LATENCY_CTRL_WR_SHIFT) |
+			((data[2] - 1) << L2X0_LATENCY_CTRL_SETUP_SHIFT),
+			l2x0_base + L2X0_DATA_LATENCY_CTRL);
+
+	of_property_read_u32_array(np, "arm,filter-ranges",
+				   filter, ARRAY_SIZE(filter));
+	if (filter[1]) {
+		writel_relaxed(ALIGN(filter[0] + filter[1], SZ_1M),
+			       l2x0_base + L2X0_ADDR_FILTER_END);
+		writel_relaxed((filter[0] & ~(SZ_1M - 1)) | L2X0_ADDR_FILTER_EN,
+			       l2x0_base + L2X0_ADDR_FILTER_START);
+	}
+}
+
+static void __init pl310_save(void)
+{
+	u32 l2x0_revision = readl_relaxed(l2x0_base + L2X0_CACHE_ID) &
+		L2X0_CACHE_ID_RTL_MASK;
+
+	l2x0_saved_regs.tag_latency = readl_relaxed(l2x0_base +
+		L2X0_TAG_LATENCY_CTRL);
+	l2x0_saved_regs.data_latency = readl_relaxed(l2x0_base +
+		L2X0_DATA_LATENCY_CTRL);
+	l2x0_saved_regs.filter_end = readl_relaxed(l2x0_base +
+		L2X0_ADDR_FILTER_END);
+	l2x0_saved_regs.filter_start = readl_relaxed(l2x0_base +
+		L2X0_ADDR_FILTER_START);
+
+	if (l2x0_revision >= L2X0_CACHE_ID_RTL_R2P0) {
+		/*
+		 * From r2p0, there is Prefetch offset/control register
+		 */
+		l2x0_saved_regs.prefetch_ctrl = readl_relaxed(l2x0_base +
+			L2X0_PREFETCH_CTRL);
+		/*
+		 * From r3p0, there is Power control register
+		 */
+		if (l2x0_revision >= L2X0_CACHE_ID_RTL_R3P0)
+			l2x0_saved_regs.pwr_ctrl = readl_relaxed(l2x0_base +
+				L2X0_POWER_CTRL);
+	}
+}
+
+static void l2x0_resume(void)
+{
+	if (!(readl_relaxed(l2x0_base + L2X0_CTRL) & 1)) {
+		/* restore aux ctrl and enable l2 */
+		l2x0_unlock(readl_relaxed(l2x0_base + L2X0_CACHE_ID));
+
+		writel_relaxed(l2x0_saved_regs.aux_ctrl, l2x0_base +
+			L2X0_AUX_CTRL);
+
+		l2x0_inv_all();
+
+		writel_relaxed(1, l2x0_base + L2X0_CTRL);
+	}
+}
+
+static void pl310_resume(void)
+{
+	u32 l2x0_revision;
+
+	if (!(readl_relaxed(l2x0_base + L2X0_CTRL) & 1)) {
+		/* restore pl310 setup */
+		writel_relaxed(l2x0_saved_regs.tag_latency,
+			l2x0_base + L2X0_TAG_LATENCY_CTRL);
+		writel_relaxed(l2x0_saved_regs.data_latency,
+			l2x0_base + L2X0_DATA_LATENCY_CTRL);
+		writel_relaxed(l2x0_saved_regs.filter_end,
+			l2x0_base + L2X0_ADDR_FILTER_END);
+		writel_relaxed(l2x0_saved_regs.filter_start,
+			l2x0_base + L2X0_ADDR_FILTER_START);
+
+		l2x0_revision = readl_relaxed(l2x0_base + L2X0_CACHE_ID) &
+			L2X0_CACHE_ID_RTL_MASK;
+
+		if (l2x0_revision >= L2X0_CACHE_ID_RTL_R2P0) {
+			writel_relaxed(l2x0_saved_regs.prefetch_ctrl,
+				l2x0_base + L2X0_PREFETCH_CTRL);
+			if (l2x0_revision >= L2X0_CACHE_ID_RTL_R3P0)
+				writel_relaxed(l2x0_saved_regs.pwr_ctrl,
+					l2x0_base + L2X0_POWER_CTRL);
+		}
+	}
+
+	l2x0_resume();
+}
+
+static const struct l2x0_of_data pl310_data = {
+	pl310_of_setup,
+	pl310_save,
+	pl310_resume,
+};
+
+static const struct l2x0_of_data l2x0_data = {
+	l2x0_of_setup,
+	NULL,
+	l2x0_resume,
+};
+
+static const struct of_device_id l2x0_ids[] __initconst = {
+	{ .compatible = "arm,pl310-cache", .data = (void *)&pl310_data },
+	{ .compatible = "arm,l220-cache", .data = (void *)&l2x0_data },
+	{ .compatible = "arm,l210-cache", .data = (void *)&l2x0_data },
+	{}
+};
+
+int __init l2x0_of_init(__u32 aux_val, __u32 aux_mask)
+{
+	struct device_node *np;
+	struct l2x0_of_data *data;
+	struct resource res;
+
+	np = of_find_matching_node(NULL, l2x0_ids);
+	if (!np)
+		return -ENODEV;
+
+	if (of_address_to_resource(np, 0, &res))
+		return -ENODEV;
+
+	l2x0_base = ioremap(res.start, resource_size(&res));
+	if (!l2x0_base)
+		return -ENOMEM;
+
+	l2x0_saved_regs.phy_base = res.start;
+
+	data = of_match_node(l2x0_ids, np)->data;
+
+	/* L2 configuration can only be changed if the cache is disabled */
+	if (!(readl_relaxed(l2x0_base + L2X0_CTRL) & 1)) {
+		if (data->setup)
+			data->setup(np, &aux_val, &aux_mask);
+	}
+
+	if (data->save)
+		data->save();
+
+	l2x0_init(l2x0_base, aux_val, aux_mask);
+
+	outer_cache.resume = data->resume;
+	return 0;
+}
+#endif
diff --git a/arch/arm/plat-mxc/include/mach/gpio.h b/arch/arm/plat-mxc/include/mach/gpio.h
index 44af0064ba1a..40a8c178f10d 100644
--- a/arch/arm/plat-mxc/include/mach/gpio.h
+++ b/arch/arm/plat-mxc/include/mach/gpio.h
@@ -1,32 +1 @@
-/*
- * Copyright 2007 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright 2008 Juergen Beisert, kernel@pengutronix.de
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
- */
-
-#ifndef __ASM_ARCH_MXC_GPIO_H__
-#define __ASM_ARCH_MXC_GPIO_H__
-
-#include <linux/spinlock.h>
-#include <mach/hardware.h>
-#include <asm-generic/gpio.h>
-
-/* use gpiolib dispatchers */
-#define gpio_get_value		__gpio_get_value
-#define gpio_set_value		__gpio_set_value
-#define gpio_cansleep		__gpio_cansleep
-#define gpio_to_irq		__gpio_to_irq
-
-#endif
+/* empty */
diff --git a/arch/arm/plat-nomadik/include/plat/gpio.h b/arch/arm/plat-nomadik/include/plat/gpio-nomadik.h
index d5d7e651269c..3ba4d8f8073b 100644
--- a/arch/arm/plat-nomadik/include/plat/gpio.h
+++ b/arch/arm/plat-nomadik/include/plat/gpio-nomadik.h
@@ -9,20 +9,9 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-#ifndef __ASM_PLAT_GPIO_H
-#define __ASM_PLAT_GPIO_H
 
-#include <asm-generic/gpio.h>
-
-/*
- * These currently cause a function call to happen, they may be optimized
- * if needed by adding cpu-specific defines to identify blocks
- * (see mach-pxa/include/mach/gpio.h as an example using GPLR etc)
- */
-#define gpio_get_value  __gpio_get_value
-#define gpio_set_value  __gpio_set_value
-#define gpio_cansleep   __gpio_cansleep
-#define gpio_to_irq     __gpio_to_irq
+#ifndef __PLAT_NOMADIK_GPIO
+#define __PLAT_NOMADIK_GPIO
 
 /*
  * "nmk_gpio" and "NMK_GPIO" stand for "Nomadik GPIO", leaving
@@ -93,4 +82,4 @@ struct nmk_gpio_platform_data {
 	bool supports_sleepmode;
 };
 
-#endif /* __ASM_PLAT_GPIO_H */
+#endif /* __PLAT_NOMADIK_GPIO */
diff --git a/arch/arm/plat-omap/debug-devices.c b/arch/arm/plat-omap/debug-devices.c
index 923c9621096b..caa1f7b6cc21 100644
--- a/arch/arm/plat-omap/debug-devices.c
+++ b/arch/arm/plat-omap/debug-devices.c
@@ -8,7 +8,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
@@ -18,7 +18,6 @@
 #include <mach/hardware.h>
 
 #include <plat/board.h>
-#include <mach/gpio.h>
 
 
 /* Many OMAP development platforms reuse the same "debug board"; these
diff --git a/arch/arm/plat-omap/debug-leds.c b/arch/arm/plat-omap/debug-leds.c
index fc05b1022602..61a1ec2a6af4 100644
--- a/arch/arm/plat-omap/debug-leds.c
+++ b/arch/arm/plat-omap/debug-leds.c
@@ -7,7 +7,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
 #include <linux/leds.h>
@@ -19,7 +19,6 @@
 #include <asm/mach-types.h>
 
 #include <plat/fpga.h>
-#include <mach/gpio.h>
 
 
 /* Many OMAP development platforms reuse the same "debug board"; these
diff --git a/arch/arm/plat-omap/devices.c b/arch/arm/plat-omap/devices.c
index bd9a06b3ee89..acd132c29647 100644
--- a/arch/arm/plat-omap/devices.c
+++ b/arch/arm/plat-omap/devices.c
@@ -8,7 +8,7 @@
  * the Free Software Foundation; either version 2 of the License, or
  * (at your option) any later version.
  */
-
+#include <linux/gpio.h>
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -24,7 +24,6 @@
 #include <plat/tc.h>
 #include <plat/board.h>
 #include <plat/mmc.h>
-#include <mach/gpio.h>
 #include <plat/menelaus.h>
 #include <plat/omap44xx.h>
 
diff --git a/arch/arm/plat-omap/include/plat/gpio.h b/arch/arm/plat-omap/include/plat/gpio.h
index 91e8de3db085..9e86ee0aed0a 100644
--- a/arch/arm/plat-omap/include/plat/gpio.h
+++ b/arch/arm/plat-omap/include/plat/gpio.h
@@ -222,26 +222,6 @@ extern void omap_gpio_restore_context(void);
 #include <linux/errno.h>
 #include <asm-generic/gpio.h>
 
-static inline int gpio_get_value(unsigned gpio)
-{
-	return __gpio_get_value(gpio);
-}
-
-static inline void gpio_set_value(unsigned gpio, int value)
-{
-	__gpio_set_value(gpio, value);
-}
-
-static inline int gpio_cansleep(unsigned gpio)
-{
-	return __gpio_cansleep(gpio);
-}
-
-static inline int gpio_to_irq(unsigned gpio)
-{
-	return __gpio_to_irq(gpio);
-}
-
 static inline int irq_to_gpio(unsigned irq)
 {
 	int tmp;
diff --git a/arch/arm/plat-orion/include/plat/gpio.h b/arch/arm/plat-orion/include/plat/gpio.h
index 3075b9fdde83..3abf30428bee 100644
--- a/arch/arm/plat-orion/include/plat/gpio.h
+++ b/arch/arm/plat-orion/include/plat/gpio.h
@@ -12,15 +12,7 @@
 #define __PLAT_GPIO_H
 
 #include <linux/init.h>
-#include <asm-generic/gpio.h>
-
-/*
- * GENERIC_GPIO primitives.
- */
-#define gpio_get_value  __gpio_get_value
-#define gpio_set_value  __gpio_set_value
-#define gpio_cansleep   __gpio_cansleep
-#define gpio_to_irq     __gpio_to_irq
+#include <linux/types.h>
 
 /*
  * Orion-specific GPIO API extensions.
diff --git a/arch/arm/plat-pxa/Makefile b/arch/arm/plat-pxa/Makefile
index 3aca5ba0f876..f302d048392d 100644
--- a/arch/arm/plat-pxa/Makefile
+++ b/arch/arm/plat-pxa/Makefile
@@ -4,7 +4,6 @@
 
 obj-y	:= dma.o
 
-obj-$(CONFIG_GENERIC_GPIO)	+= gpio.o
 obj-$(CONFIG_PXA3xx)		+= mfp.o
 obj-$(CONFIG_PXA95x)		+= mfp.o
 obj-$(CONFIG_ARCH_MMP)		+= mfp.o
diff --git a/arch/arm/plat-pxa/include/plat/gpio-pxa.h b/arch/arm/plat-pxa/include/plat/gpio-pxa.h
new file mode 100644
index 000000000000..b6390beff323
--- /dev/null
+++ b/arch/arm/plat-pxa/include/plat/gpio-pxa.h
@@ -0,0 +1,44 @@
+#ifndef __PLAT_PXA_GPIO_H
+#define __PLAT_PXA_GPIO_H
+
+struct irq_data;
+
+/*
+ * We handle the GPIOs by banks, each bank covers up to 32 GPIOs with
+ * one set of registers. The register offsets are organized below:
+ *
+ *           GPLR    GPDR    GPSR    GPCR    GRER    GFER    GEDR
+ * BANK 0 - 0x0000  0x000C  0x0018  0x0024  0x0030  0x003C  0x0048
+ * BANK 1 - 0x0004  0x0010  0x001C  0x0028  0x0034  0x0040  0x004C
+ * BANK 2 - 0x0008  0x0014  0x0020  0x002C  0x0038  0x0044  0x0050
+ *
+ * BANK 3 - 0x0100  0x010C  0x0118  0x0124  0x0130  0x013C  0x0148
+ * BANK 4 - 0x0104  0x0110  0x011C  0x0128  0x0134  0x0140  0x014C
+ * BANK 5 - 0x0108  0x0114  0x0120  0x012C  0x0138  0x0144  0x0150
+ *
+ * NOTE:
+ *   BANK 3 is only available on PXA27x and later processors.
+ *   BANK 4 and 5 are only available on PXA935
+ */
+
+#define GPIO_BANK(n)	(GPIO_REGS_VIRT + BANK_OFF(n))
+
+#define GPLR_OFFSET	0x00
+#define GPDR_OFFSET	0x0C
+#define GPSR_OFFSET	0x18
+#define GPCR_OFFSET	0x24
+#define GRER_OFFSET	0x30
+#define GFER_OFFSET	0x3C
+#define GEDR_OFFSET	0x48
+
+/* NOTE: some PXAs have fewer on-chip GPIOs (like PXA255, with 85).
+ * Those cases currently cause holes in the GPIO number space, the
+ * actual number of the last GPIO is recorded by 'pxa_last_gpio'.
+ */
+extern int pxa_last_gpio;
+
+typedef int (*set_wake_t)(struct irq_data *d, unsigned int on);
+
+extern void pxa_init_gpio(int mux_irq, int start, int end, set_wake_t fn);
+
+#endif /* __PLAT_PXA_GPIO_H */
diff --git a/arch/arm/plat-pxa/include/plat/gpio.h b/arch/arm/plat-pxa/include/plat/gpio.h
index 1ddd2b97a729..258f77210b02 100644
--- a/arch/arm/plat-pxa/include/plat/gpio.h
+++ b/arch/arm/plat-pxa/include/plat/gpio.h
@@ -1,35 +1,10 @@
 #ifndef __PLAT_GPIO_H
 #define __PLAT_GPIO_H
 
-struct irq_data;
+#define __ARM_GPIOLIB_COMPLEX
 
-/*
- * We handle the GPIOs by banks, each bank covers up to 32 GPIOs with
- * one set of registers. The register offsets are organized below:
- *
- *           GPLR    GPDR    GPSR    GPCR    GRER    GFER    GEDR
- * BANK 0 - 0x0000  0x000C  0x0018  0x0024  0x0030  0x003C  0x0048
- * BANK 1 - 0x0004  0x0010  0x001C  0x0028  0x0034  0x0040  0x004C
- * BANK 2 - 0x0008  0x0014  0x0020  0x002C  0x0038  0x0044  0x0050
- *
- * BANK 3 - 0x0100  0x010C  0x0118  0x0124  0x0130  0x013C  0x0148
- * BANK 4 - 0x0104  0x0110  0x011C  0x0128  0x0134  0x0140  0x014C
- * BANK 5 - 0x0108  0x0114  0x0120  0x012C  0x0138  0x0144  0x0150
- *
- * NOTE:
- *   BANK 3 is only available on PXA27x and later processors.
- *   BANK 4 and 5 are only available on PXA935
- */
-
-#define GPIO_BANK(n)	(GPIO_REGS_VIRT + BANK_OFF(n))
-
-#define GPLR_OFFSET	0x00
-#define GPDR_OFFSET	0x0C
-#define GPSR_OFFSET	0x18
-#define GPCR_OFFSET	0x24
-#define GRER_OFFSET	0x30
-#define GFER_OFFSET	0x3C
-#define GEDR_OFFSET	0x48
+/* The individual machine provides register offsets and NR_BUILTIN_GPIO */
+#include <mach/gpio-pxa.h>
 
 static inline int gpio_get_value(unsigned gpio)
 {
@@ -52,13 +27,4 @@ static inline void gpio_set_value(unsigned gpio, int value)
 
 #define gpio_cansleep		__gpio_cansleep
 
-/* NOTE: some PXAs have fewer on-chip GPIOs (like PXA255, with 85).
- * Those cases currently cause holes in the GPIO number space, the
- * actual number of the last GPIO is recorded by 'pxa_last_gpio'.
- */
-extern int pxa_last_gpio;
-
-typedef int (*set_wake_t)(struct irq_data *d, unsigned int on);
-
-extern void pxa_init_gpio(int mux_irq, int start, int end, set_wake_t fn);
 #endif /* __PLAT_GPIO_H */
diff --git a/arch/arm/plat-spear/include/plat/gpio.h b/arch/arm/plat-spear/include/plat/gpio.h
index b857c91257dd..40a8c178f10d 100644
--- a/arch/arm/plat-spear/include/plat/gpio.h
+++ b/arch/arm/plat-spear/include/plat/gpio.h
@@ -1,24 +1 @@
-/*
- * arch/arm/plat-spear/include/plat/gpio.h
- *
- * GPIO macros for SPEAr platform
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __PLAT_GPIO_H
-#define __PLAT_GPIO_H
-
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value	__gpio_get_value
-#define gpio_set_value	__gpio_set_value
-#define gpio_cansleep	__gpio_cansleep
-#define gpio_to_irq	__gpio_to_irq
-
-#endif /* __PLAT_GPIO_H */
+/* empty */
diff --git a/drivers/ata/pata_at91.c b/drivers/ata/pata_at91.c
index 960c72571395..3f4c2613b3df 100644
--- a/drivers/ata/pata_at91.c
+++ b/drivers/ata/pata_at91.c
@@ -30,7 +30,7 @@
 
 #include <mach/at91sam9_smc.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
 
 #define DRV_NAME		"pata_at91"
 #define DRV_VERSION		"0.3"
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index d539efd96d4b..4caa3d37bbde 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -178,6 +178,15 @@ config GPIO_SCH
 	  The Intel Tunnel Creek processor has 5 GPIOs powered by the
 	  core power rail and 9 from suspend power supply.
 
+config GPIO_U300
+	bool "ST-Ericsson U300 COH 901 335/571 GPIO"
+	depends on GPIOLIB && ARCH_U300
+	help
+	  Say yes here to support GPIO interface on ST-Ericsson U300.
+	  The names of the two IP block variants supported are
+	  COH 901 335 and COH 901 571/3. They contain 3, 5 or 7
+	  ports of 8 GPIO pins each.
+
 config GPIO_VX855
 	tristate "VIA VX855/VX875 GPIO"
 	depends on MFD_SUPPORT && PCI
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 9588948c96f0..19c5d27b6d2e 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -14,11 +14,14 @@ obj-$(CONFIG_GPIO_ADP5588)	+= gpio-adp5588.o
 obj-$(CONFIG_GPIO_BT8XX)	+= gpio-bt8xx.o
 obj-$(CONFIG_GPIO_CS5535)	+= gpio-cs5535.o
 obj-$(CONFIG_GPIO_DA9052)	+= gpio-da9052.o
+obj-$(CONFIG_ARCH_DAVINCI)	+= gpio-davinci.o
 obj-$(CONFIG_GPIO_EP93XX)	+= gpio-ep93xx.o
 obj-$(CONFIG_GPIO_EXYNOS4)	+= gpio-exynos4.o
 obj-$(CONFIG_GPIO_IT8761E)	+= gpio-it8761e.o
 obj-$(CONFIG_GPIO_JANZ_TTL)	+= gpio-janz-ttl.o
+obj-$(CONFIG_MACH_KS8695)	+= gpio-ks8695.o
 obj-$(CONFIG_GPIO_LANGWELL)	+= gpio-langwell.o
+obj-$(CONFIG_ARCH_LPC32XX)	+= gpio-lpc32xx.o
 obj-$(CONFIG_GPIO_MAX730X)	+= gpio-max730x.o
 obj-$(CONFIG_GPIO_MAX7300)	+= gpio-max7300.o
 obj-$(CONFIG_GPIO_MAX7301)	+= gpio-max7301.o
@@ -37,18 +40,20 @@ obj-$(CONFIG_GPIO_PCA953X)	+= gpio-pca953x.o
 obj-$(CONFIG_GPIO_PCF857X)	+= gpio-pcf857x.o
 obj-$(CONFIG_GPIO_PCH)		+= gpio-pch.o
 obj-$(CONFIG_GPIO_PL061)	+= gpio-pl061.o
+obj-$(CONFIG_PLAT_PXA)		+= gpio-pxa.o
 obj-$(CONFIG_GPIO_RDC321X)	+= gpio-rdc321x.o
 
 obj-$(CONFIG_GPIO_PLAT_SAMSUNG)	+= gpio-plat-samsung.o
 obj-$(CONFIG_GPIO_S5PC100)	+= gpio-s5pc100.o
 obj-$(CONFIG_GPIO_S5PV210)	+= gpio-s5pv210.o
-
+obj-$(CONFIG_ARCH_SA1100)	+= gpio-sa1100.o
 obj-$(CONFIG_GPIO_SCH)		+= gpio-sch.o
 obj-$(CONFIG_GPIO_STMPE)	+= gpio-stmpe.o
 obj-$(CONFIG_GPIO_SX150X)	+= gpio-sx150x.o
 obj-$(CONFIG_GPIO_TC3589X)	+= gpio-tc3589x.o
 obj-$(CONFIG_ARCH_TEGRA)	+= gpio-tegra.o
 obj-$(CONFIG_GPIO_TIMBERDALE)	+= gpio-timberdale.o
+obj-$(CONFIG_ARCH_DAVINCI_TNETV107X) += gpio-tnetv107x.o
 obj-$(CONFIG_GPIO_TPS65910)	+= gpio-tps65910.o
 obj-$(CONFIG_GPIO_TPS65912)	+= gpio-tps65912.o
 obj-$(CONFIG_GPIO_TWL4030)	+= gpio-twl4030.o
diff --git a/arch/arm/mach-davinci/gpio.c b/drivers/gpio/gpio-davinci.c
index cafbe13a82a5..df0d59570a84 100644
--- a/arch/arm/mach-davinci/gpio.c
+++ b/drivers/gpio/gpio-davinci.c
@@ -9,15 +9,13 @@
  * the Free Software Foundation; either version 2 of the License, or
  * (at your option) any later version.
  */
-
+#include <linux/gpio.h>
 #include <linux/errno.h>
 #include <linux/kernel.h>
 #include <linux/clk.h>
 #include <linux/err.h>
 #include <linux/io.h>
 
-#include <mach/gpio.h>
-
 #include <asm/mach/irq.h>
 
 struct davinci_gpio_regs {
@@ -232,9 +230,6 @@ static void gpio_irq_enable(struct irq_data *d)
 
 static int gpio_irq_type(struct irq_data *d, unsigned trigger)
 {
-	struct davinci_gpio_regs __iomem *g = irq2regs(d->irq);
-	u32 mask = (u32) irq_data_get_irq_handler_data(d);
-
 	if (trigger & ~(IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_EDGE_RISING))
 		return -EINVAL;
 
diff --git a/drivers/gpio/gpio-ep93xx.c b/drivers/gpio/gpio-ep93xx.c
index 72fb9c665320..7aafbb437339 100644
--- a/drivers/gpio/gpio-ep93xx.c
+++ b/drivers/gpio/gpio-ep93xx.c
@@ -23,6 +23,9 @@
 #include <linux/basic_mmio_gpio.h>
 
 #include <mach/hardware.h>
+#include <mach/gpio-ep93xx.h>
+
+#define irq_to_gpio(irq)	((irq) - gpio_to_irq(0))
 
 struct ep93xx_gpio {
 	void __iomem		*mmio_base;
@@ -307,6 +310,21 @@ static int ep93xx_gpio_set_debounce(struct gpio_chip *chip,
 	return 0;
 }
 
+/*
+ * Map GPIO A0..A7  (0..7)  to irq 64..71,
+ *          B0..B7  (7..15) to irq 72..79, and
+ *          F0..F7 (16..24) to irq 80..87.
+ */
+static int ep93xx_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
+{
+	int gpio = chip->base + offset;
+
+	if (gpio > EP93XX_GPIO_LINE_MAX_IRQ)
+		return -EINVAL;
+
+	return 64 + gpio;
+}
+
 static int ep93xx_gpio_add_bank(struct bgpio_chip *bgc, struct device *dev,
 	void __iomem *mmio_base, struct ep93xx_gpio_bank *bank)
 {
@@ -321,8 +339,10 @@ static int ep93xx_gpio_add_bank(struct bgpio_chip *bgc, struct device *dev,
 	bgc->gc.label = bank->label;
 	bgc->gc.base = bank->base;
 
-	if (bank->has_debounce)
+	if (bank->has_debounce) {
 		bgc->gc.set_debounce = ep93xx_gpio_set_debounce;
+		bgc->gc.to_irq = ep93xx_gpio_to_irq;
+	}
 
 	return gpiochip_add(&bgc->gc);
 }
diff --git a/arch/arm/mach-ks8695/gpio.c b/drivers/gpio/gpio-ks8695.c
index 31e456508a6f..a3ac66ea364b 100644
--- a/arch/arm/mach-ks8695/gpio.c
+++ b/drivers/gpio/gpio-ks8695.c
@@ -18,7 +18,7 @@
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/mm.h>
 #include <linux/init.h>
@@ -31,7 +31,7 @@
 #include <asm/mach/irq.h>
 
 #include <mach/regs-gpio.h>
-#include <mach/gpio.h>
+#include <mach/gpio-ks8695.h>
 
 /*
  * Configure a GPIO line for either GPIO function, or its internal
diff --git a/arch/arm/mach-lpc32xx/gpiolib.c b/drivers/gpio/gpio-lpc32xx.c
index 69061ea8997a..5b6948081f8f 100644
--- a/arch/arm/mach-lpc32xx/gpiolib.c
+++ b/drivers/gpio/gpio-lpc32xx.c
@@ -24,7 +24,7 @@
 
 #include <mach/hardware.h>
 #include <mach/platform.h>
-#include "common.h"
+#include <mach/gpio-lpc32xx.h>
 
 #define LPC32XX_GPIO_P3_INP_STATE		_GPREG(0x000)
 #define LPC32XX_GPIO_P3_OUTP_SET		_GPREG(0x004)
diff --git a/drivers/gpio/gpio-nomadik.c b/drivers/gpio/gpio-nomadik.c
index 2c212c732d76..740caed2b278 100644
--- a/drivers/gpio/gpio-nomadik.c
+++ b/drivers/gpio/gpio-nomadik.c
@@ -27,8 +27,9 @@
 #include <asm/mach/irq.h>
 
 #include <plat/pincfg.h>
+#include <plat/gpio-nomadik.h>
 #include <mach/hardware.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
 
 /*
  * The GPIO module in the Nomadik family of Systems-on-Chip is an
diff --git a/drivers/gpio/gpio-omap.c b/drivers/gpio/gpio-omap.c
index 118ec12d2d5f..0e49d87f6c60 100644
--- a/drivers/gpio/gpio-omap.c
+++ b/drivers/gpio/gpio-omap.c
@@ -25,7 +25,7 @@
 #include <mach/hardware.h>
 #include <asm/irq.h>
 #include <mach/irqs.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
 #include <asm/mach/irq.h>
 
 struct gpio_bank {
diff --git a/arch/arm/plat-pxa/gpio.c b/drivers/gpio/gpio-pxa.c
index a11dc3670505..9052925c6fa2 100644
--- a/arch/arm/plat-pxa/gpio.c
+++ b/drivers/gpio/gpio-pxa.c
@@ -11,14 +11,14 @@
  *  it under the terms of the GNU General Public License version 2 as
  *  published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/irq.h>
 #include <linux/io.h>
 #include <linux/syscore_ops.h>
 #include <linux/slab.h>
 
-#include <mach/gpio.h>
+#include <mach/gpio-pxa.h>
 
 int pxa_last_gpio;
 
diff --git a/arch/arm/mach-sa1100/gpio.c b/drivers/gpio/gpio-sa1100.c
index 0d3829a8c2c1..b6c1f6d80649 100644
--- a/arch/arm/mach-sa1100/gpio.c
+++ b/drivers/gpio/gpio-sa1100.c
@@ -7,13 +7,11 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/module.h>
 
-#include <asm/gpio.h>
 #include <mach/hardware.h>
-#include "generic.h"
 
 static int sa1100_gpio_get(struct gpio_chip *chip, unsigned offset)
 {
diff --git a/drivers/gpio/gpio-tegra.c b/drivers/gpio/gpio-tegra.c
index 747eb40e8afe..6b65207c8106 100644
--- a/drivers/gpio/gpio-tegra.c
+++ b/drivers/gpio/gpio-tegra.c
@@ -27,6 +27,7 @@
 
 #include <asm/mach/irq.h>
 
+#include <mach/gpio-tegra.h>
 #include <mach/iomap.h>
 #include <mach/suspend.h>
 
@@ -134,7 +135,10 @@ static int tegra_gpio_direction_output(struct gpio_chip *chip, unsigned offset,
 	return 0;
 }
 
-
+static int tegra_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
+{
+	return TEGRA_GPIO_TO_IRQ(offset);
+}
 
 static struct gpio_chip tegra_gpio_chip = {
 	.label			= "tegra-gpio",
@@ -142,6 +146,7 @@ static struct gpio_chip tegra_gpio_chip = {
 	.get			= tegra_gpio_get,
 	.direction_output	= tegra_gpio_direction_output,
 	.set			= tegra_gpio_set,
+	.to_irq			= tegra_gpio_to_irq,
 	.base			= 0,
 	.ngpio			= TEGRA_NR_GPIOS,
 };
@@ -331,6 +336,7 @@ static struct lock_class_key gpio_lock_class;
 static int __init tegra_gpio_init(void)
 {
 	struct tegra_gpio_bank *bank;
+	int gpio;
 	int i;
 	int j;
 
@@ -352,14 +358,17 @@ static int __init tegra_gpio_init(void)
 
 	gpiochip_add(&tegra_gpio_chip);
 
-	for (i = INT_GPIO_BASE; i < (INT_GPIO_BASE + TEGRA_NR_GPIOS); i++) {
-		bank = &tegra_gpio_banks[GPIO_BANK(irq_to_gpio(i))];
+	for (gpio = 0; gpio < TEGRA_NR_GPIOS; gpio++) {
+		int irq = TEGRA_GPIO_TO_IRQ(gpio);
+		/* No validity check; all Tegra GPIOs are valid IRQs */
+
+		bank = &tegra_gpio_banks[GPIO_BANK(gpio)];
 
-		irq_set_lockdep_class(i, &gpio_lock_class);
-		irq_set_chip_data(i, bank);
-		irq_set_chip_and_handler(i, &tegra_gpio_irq_chip,
+		irq_set_lockdep_class(irq, &gpio_lock_class);
+		irq_set_chip_data(irq, bank);
+		irq_set_chip_and_handler(irq, &tegra_gpio_irq_chip,
 					 handle_simple_irq);
-		set_irq_flags(i, IRQF_VALID);
+		set_irq_flags(irq, IRQF_VALID);
 	}
 
 	for (i = 0; i < ARRAY_SIZE(tegra_gpio_banks); i++) {
diff --git a/arch/arm/mach-davinci/gpio-tnetv107x.c b/drivers/gpio/gpio-tnetv107x.c
index 3fa3e2867e19..3fa3e2867e19 100644
--- a/arch/arm/mach-davinci/gpio-tnetv107x.c
+++ b/drivers/gpio/gpio-tnetv107x.c
diff --git a/drivers/gpio/gpio-u300.c b/drivers/gpio/gpio-u300.c
index 53e8255cb0ba..4035778852b0 100644
--- a/drivers/gpio/gpio-u300.c
+++ b/drivers/gpio/gpio-u300.c
@@ -1,18 +1,17 @@
 /*
  * U300 GPIO module.
  *
- * Copyright (C) 2007-2009 ST-Ericsson AB
+ * Copyright (C) 2007-2011 ST-Ericsson AB
  * License terms: GNU General Public License (GPL) version 2
  * This can driver either of the two basic GPIO cores
  * available in the U300 platforms:
  * COH 901 335   - Used in DB3150 (U300 1.0) and DB3200 (U330 1.0)
  * COH 901 571/3 - Used in DB3210 (U365 2.0) and DB3350 (U335 1.0)
- * Notice that you also have inline macros in <asm-arch/gpio.h>
- * Author: Linus Walleij <linus.walleij@stericsson.com>
+ * Author: Linus Walleij <linus.walleij@linaro.org>
  * Author: Jonas Aaberg <jonas.aberg@stericsson.com>
- *
  */
 #include <linux/module.h>
+#include <linux/irq.h>
 #include <linux/interrupt.h>
 #include <linux/delay.h>
 #include <linux/errno.h>
@@ -21,677 +20,898 @@
 #include <linux/err.h>
 #include <linux/platform_device.h>
 #include <linux/gpio.h>
+#include <linux/list.h>
+#include <linux/slab.h>
+#include <mach/gpio-u300.h>
 
-/* Reference to GPIO block clock */
-static struct clk *clk;
+/*
+ * Bias modes for U300 GPIOs
+ *
+ * GPIO_U300_CONFIG_BIAS_UNKNOWN: this bias mode is not known to us
+ * GPIO_U300_CONFIG_BIAS_FLOAT: no specific bias, the GPIO will float or state
+ *	is not controlled by software
+ * GPIO_U300_CONFIG_BIAS_PULL_UP: the GPIO will be pulled up (usually with high
+ *	impedance to VDD)
+ */
+#define GPIO_U300_CONFIG_BIAS_UNKNOWN	0x1000
+#define GPIO_U300_CONFIG_BIAS_FLOAT	0x1001
+#define GPIO_U300_CONFIG_BIAS_PULL_UP	0x1002
 
-/* Memory resource */
-static struct resource *memres;
-static void __iomem *virtbase;
-static struct device *gpiodev;
+/*
+ * Drive modes for U300 GPIOs (output)
+ *
+ * GPIO_U300_CONFIG_DRIVE_PUSH_PULL: the GPIO will be driven actively high and
+ *	low, this is the most typical case and is typically achieved with two
+ *	active transistors on the output
+ * GPIO_U300_CONFIG_DRIVE_OPEN_DRAIN: the GPIO will be driven with open drain
+ *	(open collector) which means it is usually wired with other output
+ *	ports which are then pulled up with an external resistor
+ * GPIO_U300_CONFIG_DRIVE_OPEN_SOURCE: the GPIO will be driven with open drain
+ *	(open emitter) which is the same as open drain mutatis mutandis but
+ *	pulled to ground
+ */
+#define GPIO_U300_CONFIG_DRIVE_PUSH_PULL	0x2000
+#define GPIO_U300_CONFIG_DRIVE_OPEN_DRAIN	0x2001
+#define GPIO_U300_CONFIG_DRIVE_OPEN_SOURCE	0x2002
+
+/*
+ * Register definitions for COH 901 335 variant
+ */
+#define U300_335_PORT_STRIDE				(0x1C)
+/* Port X Pin Data Register 32bit, this is both input and output (R/W) */
+#define U300_335_PXPDIR					(0x00)
+#define U300_335_PXPDOR					(0x00)
+/* Port X Pin Config Register 32bit (R/W) */
+#define U300_335_PXPCR					(0x04)
+/* This register layout is the same in both blocks */
+#define U300_GPIO_PXPCR_ALL_PINS_MODE_MASK		(0x0000FFFFUL)
+#define U300_GPIO_PXPCR_PIN_MODE_MASK			(0x00000003UL)
+#define U300_GPIO_PXPCR_PIN_MODE_SHIFT			(0x00000002UL)
+#define U300_GPIO_PXPCR_PIN_MODE_INPUT			(0x00000000UL)
+#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL	(0x00000001UL)
+#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN	(0x00000002UL)
+#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE	(0x00000003UL)
+/* Port X Interrupt Event Register 32bit (R/W) */
+#define U300_335_PXIEV					(0x08)
+/* Port X Interrupt Enable Register 32bit (R/W) */
+#define U300_335_PXIEN					(0x0C)
+/* Port X Interrupt Force Register 32bit (R/W) */
+#define U300_335_PXIFR					(0x10)
+/* Port X Interrupt Config Register 32bit (R/W) */
+#define U300_335_PXICR					(0x14)
+/* This register layout is the same in both blocks */
+#define U300_GPIO_PXICR_ALL_IRQ_CONFIG_MASK		(0x000000FFUL)
+#define U300_GPIO_PXICR_IRQ_CONFIG_MASK			(0x00000001UL)
+#define U300_GPIO_PXICR_IRQ_CONFIG_FALLING_EDGE		(0x00000000UL)
+#define U300_GPIO_PXICR_IRQ_CONFIG_RISING_EDGE		(0x00000001UL)
+/* Port X Pull-up Enable Register 32bit (R/W) */
+#define U300_335_PXPER					(0x18)
+/* This register layout is the same in both blocks */
+#define U300_GPIO_PXPER_ALL_PULL_UP_DISABLE_MASK	(0x000000FFUL)
+#define U300_GPIO_PXPER_PULL_UP_DISABLE			(0x00000001UL)
+/* Control Register 32bit (R/W) */
+#define U300_335_CR					(0x54)
+#define U300_335_CR_BLOCK_CLOCK_ENABLE			(0x00000001UL)
+
+/*
+ * Register definitions for COH 901 571 / 3 variant
+ */
+#define U300_571_PORT_STRIDE				(0x30)
+/*
+ * Control Register 32bit (R/W)
+ * bit 15-9 (mask 0x0000FE00) contains the number of cores. 8*cores
+ * gives the number of GPIO pins.
+ * bit 8-2  (mask 0x000001FC) contains the core version ID.
+ */
+#define U300_571_CR					(0x00)
+#define U300_571_CR_SYNC_SEL_ENABLE			(0x00000002UL)
+#define U300_571_CR_BLOCK_CLKRQ_ENABLE			(0x00000001UL)
+/*
+ * These registers have the same layout and function as the corresponding
+ * COH 901 335 registers, just at different offset.
+ */
+#define U300_571_PXPDIR					(0x04)
+#define U300_571_PXPDOR					(0x08)
+#define U300_571_PXPCR					(0x0C)
+#define U300_571_PXPER					(0x10)
+#define U300_571_PXIEV					(0x14)
+#define U300_571_PXIEN					(0x18)
+#define U300_571_PXIFR					(0x1C)
+#define U300_571_PXICR					(0x20)
+
+/* 8 bits per port, no version has more than 7 ports */
+#define U300_GPIO_PINS_PER_PORT 8
+#define U300_GPIO_MAX (U300_GPIO_PINS_PER_PORT * 7)
+
+struct u300_gpio {
+	struct gpio_chip chip;
+	struct list_head port_list;
+	struct clk *clk;
+	struct resource *memres;
+	void __iomem *base;
+	struct device *dev;
+	int irq_base;
+	u32 stride;
+	/* Register offsets */
+	u32 pcr;
+	u32 dor;
+	u32 dir;
+	u32 per;
+	u32 icr;
+	u32 ien;
+	u32 iev;
+};
 
 struct u300_gpio_port {
-	const char *name;
+	struct list_head node;
+	struct u300_gpio *gpio;
+	char name[8];
 	int irq;
 	int number;
+	u8 toggle_edge_mode;
 };
 
+/*
+ * Macro to expand to read a specific register found in the "gpio"
+ * struct. It requires the struct u300_gpio *gpio variable to exist in
+ * its context. It calculates the port offset from the given pin
+ * offset, muliplies by the port stride and adds the register offset
+ * so it provides a pointer to the desired register.
+ */
+#define U300_PIN_REG(pin, reg) \
+	(gpio->base + (pin >> 3) * gpio->stride + gpio->reg)
 
-static struct u300_gpio_port gpio_ports[] = {
-	{
-		.name = "gpio0",
-		.number = 0,
-	},
-	{
-		.name = "gpio1",
-		.number = 1,
-	},
-	{
-		.name = "gpio2",
-		.number = 2,
-	},
-#ifdef U300_COH901571_3
-	{
-		.name = "gpio3",
-		.number = 3,
-	},
-	{
-		.name = "gpio4",
-		.number = 4,
-	},
-#ifdef CONFIG_MACH_U300_BS335
-	{
-		.name = "gpio5",
-		.number = 5,
-	},
-	{
-		.name = "gpio6",
-		.number = 6,
-	},
-#endif
-#endif
+/*
+ * Provides a bitmask for a specific gpio pin inside an 8-bit GPIO
+ * register.
+ */
+#define U300_PIN_BIT(pin) \
+	(1 << (pin & 0x07))
 
+struct u300_gpio_confdata {
+	u16 bias_mode;
+	bool output;
+	int outval;
 };
 
+/* BS335 has seven ports of 8 bits each = GPIO pins 0..55 */
+#define BS335_GPIO_NUM_PORTS 7
+/* BS365 has five ports of 8 bits each = GPIO pins 0..39 */
+#define BS365_GPIO_NUM_PORTS 5
 
-#ifdef U300_COH901571_3
+#define U300_FLOATING_INPUT { \
+	.bias_mode = GPIO_U300_CONFIG_BIAS_FLOAT, \
+	.output = false, \
+}
 
-/* Default input value */
-#define DEFAULT_OUTPUT_LOW   0
-#define DEFAULT_OUTPUT_HIGH  1
+#define U300_PULL_UP_INPUT { \
+	.bias_mode = GPIO_U300_CONFIG_BIAS_PULL_UP, \
+	.output = false, \
+}
 
-/* GPIO Pull-Up status */
-#define DISABLE_PULL_UP  0
-#define ENABLE_PULL_UP  1
+#define U300_OUTPUT_LOW { \
+	.output = true, \
+	.outval = 0, \
+}
 
-#define GPIO_NOT_USED 0
-#define GPIO_IN       1
-#define GPIO_OUT      2
+#define U300_OUTPUT_HIGH { \
+	.output = true, \
+	.outval = 1, \
+}
 
-struct u300_gpio_configuration_data {
-	unsigned char pin_usage;
-	unsigned char default_output_value;
-	unsigned char pull_up;
-};
 
 /* Initial configuration */
-const struct u300_gpio_configuration_data
-u300_gpio_config[U300_GPIO_NUM_PORTS][U300_GPIO_PINS_PER_PORT] = {
-#ifdef CONFIG_MACH_U300_BS335
+static const struct __initdata u300_gpio_confdata
+bs335_gpio_config[BS335_GPIO_NUM_PORTS][U300_GPIO_PINS_PER_PORT] = {
 	/* Port 0, pins 0-7 */
 	{
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_OUT, DEFAULT_OUTPUT_HIGH,  DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_OUT, DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_OUT, DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_OUT, DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_OUT, DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_OUT, DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP}
+		U300_FLOATING_INPUT,
+		U300_OUTPUT_HIGH,
+		U300_FLOATING_INPUT,
+		U300_OUTPUT_LOW,
+		U300_OUTPUT_LOW,
+		U300_OUTPUT_LOW,
+		U300_OUTPUT_LOW,
+		U300_OUTPUT_LOW,
 	},
 	/* Port 1, pins 0-7 */
 	{
-		{GPIO_OUT, DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_OUT, DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_OUT, DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,    ENABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_OUT, DEFAULT_OUTPUT_HIGH,  DISABLE_PULL_UP},
-		{GPIO_OUT, DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_OUT, DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP}
+		U300_OUTPUT_LOW,
+		U300_OUTPUT_LOW,
+		U300_OUTPUT_LOW,
+		U300_PULL_UP_INPUT,
+		U300_FLOATING_INPUT,
+		U300_OUTPUT_HIGH,
+		U300_OUTPUT_LOW,
+		U300_OUTPUT_LOW,
 	},
 	/* Port 2, pins 0-7 */
 	{
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_OUT, DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,    ENABLE_PULL_UP},
-		{GPIO_OUT, DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,    ENABLE_PULL_UP}
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_OUTPUT_LOW,
+		U300_PULL_UP_INPUT,
+		U300_OUTPUT_LOW,
+		U300_PULL_UP_INPUT,
 	},
 	/* Port 3, pins 0-7 */
 	{
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,    ENABLE_PULL_UP},
-		{GPIO_OUT, DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP}
+		U300_PULL_UP_INPUT,
+		U300_OUTPUT_LOW,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
 	},
 	/* Port 4, pins 0-7 */
 	{
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP}
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
 	},
 	/* Port 5, pins 0-7 */
 	{
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP}
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
 	},
 	/* Port 6, pind 0-7 */
 	{
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP}
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
 	}
-#endif
+};
 
-#ifdef CONFIG_MACH_U300_BS365
+static const struct __initdata u300_gpio_confdata
+bs365_gpio_config[BS365_GPIO_NUM_PORTS][U300_GPIO_PINS_PER_PORT] = {
 	/* Port 0, pins 0-7 */
 	{
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_OUT, DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_OUT, DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_OUT, DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_OUT, DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,    ENABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP}
+		U300_FLOATING_INPUT,
+		U300_OUTPUT_LOW,
+		U300_FLOATING_INPUT,
+		U300_OUTPUT_LOW,
+		U300_OUTPUT_LOW,
+		U300_OUTPUT_LOW,
+		U300_PULL_UP_INPUT,
+		U300_FLOATING_INPUT,
 	},
 	/* Port 1, pins 0-7 */
 	{
-		{GPIO_OUT, DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_OUT, DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_OUT, DEFAULT_OUTPUT_HIGH,  DISABLE_PULL_UP},
-		{GPIO_OUT, DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_OUT, DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP}
+		U300_OUTPUT_LOW,
+		U300_FLOATING_INPUT,
+		U300_OUTPUT_LOW,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_OUTPUT_HIGH,
+		U300_OUTPUT_LOW,
+		U300_OUTPUT_LOW,
 	},
 	/* Port 2, pins 0-7 */
 	{
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,    ENABLE_PULL_UP},
-		{GPIO_OUT, DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_OUT, DEFAULT_OUTPUT_LOW,   DISABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,    ENABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,    ENABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,    ENABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,    ENABLE_PULL_UP}
+		U300_FLOATING_INPUT,
+		U300_PULL_UP_INPUT,
+		U300_OUTPUT_LOW,
+		U300_OUTPUT_LOW,
+		U300_PULL_UP_INPUT,
+		U300_PULL_UP_INPUT,
+		U300_PULL_UP_INPUT,
+		U300_PULL_UP_INPUT,
 	},
 	/* Port 3, pins 0-7 */
 	{
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,    ENABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,    ENABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,    ENABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,    ENABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,    ENABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,    ENABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,    ENABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,    ENABLE_PULL_UP}
+		U300_PULL_UP_INPUT,
+		U300_PULL_UP_INPUT,
+		U300_PULL_UP_INPUT,
+		U300_PULL_UP_INPUT,
+		U300_PULL_UP_INPUT,
+		U300_PULL_UP_INPUT,
+		U300_PULL_UP_INPUT,
+		U300_PULL_UP_INPUT,
 	},
 	/* Port 4, pins 0-7 */
 	{
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,    ENABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,    ENABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,    ENABLE_PULL_UP},
-		{GPIO_IN,  DEFAULT_OUTPUT_LOW,    ENABLE_PULL_UP},
+		U300_PULL_UP_INPUT,
+		U300_PULL_UP_INPUT,
+		U300_PULL_UP_INPUT,
+		U300_PULL_UP_INPUT,
 		/* These 4 pins doesn't exist on DB3210 */
-		{GPIO_OUT, DEFAULT_OUTPUT_LOW,    ENABLE_PULL_UP},
-		{GPIO_OUT, DEFAULT_OUTPUT_LOW,    ENABLE_PULL_UP},
-		{GPIO_OUT, DEFAULT_OUTPUT_LOW,    ENABLE_PULL_UP},
-		{GPIO_OUT, DEFAULT_OUTPUT_LOW,    ENABLE_PULL_UP}
+		U300_OUTPUT_LOW,
+		U300_OUTPUT_LOW,
+		U300_OUTPUT_LOW,
+		U300_OUTPUT_LOW,
 	}
-#endif
 };
-#endif
 
-
-/* No users == we can power down GPIO */
-static int gpio_users;
-
-struct gpio_struct {
-	int (*callback)(void *);
-	void *data;
-	int users;
-};
-
-static struct gpio_struct gpio_pin[U300_GPIO_MAX];
-
-/*
- * Let drivers register callback in order to get notified when there is
- * an interrupt on the gpio pin
+/**
+ * to_u300_gpio() - get the pointer to u300_gpio
+ * @chip: the gpio chip member of the structure u300_gpio
  */
-int gpio_register_callback(unsigned gpio, int (*func)(void *arg), void *data)
+static inline struct u300_gpio *to_u300_gpio(struct gpio_chip *chip)
 {
-	if (gpio_pin[gpio].callback)
-		dev_warn(gpiodev, "%s: WARNING: callback already "
-			 "registered for gpio pin#%d\n", __func__, gpio);
-	gpio_pin[gpio].callback = func;
-	gpio_pin[gpio].data = data;
-
-	return 0;
+	return container_of(chip, struct u300_gpio, chip);
 }
-EXPORT_SYMBOL(gpio_register_callback);
 
-int gpio_unregister_callback(unsigned gpio)
+static int u300_gpio_get(struct gpio_chip *chip, unsigned offset)
 {
-	if (!gpio_pin[gpio].callback)
-		dev_warn(gpiodev, "%s: WARNING: callback already "
-			 "unregistered for gpio pin#%d\n", __func__, gpio);
-	gpio_pin[gpio].callback = NULL;
-	gpio_pin[gpio].data = NULL;
+	struct u300_gpio *gpio = to_u300_gpio(chip);
 
-	return 0;
+	return readl(U300_PIN_REG(offset, dir)) & U300_PIN_BIT(offset);
 }
-EXPORT_SYMBOL(gpio_unregister_callback);
 
-/* Non-zero means valid */
-int gpio_is_valid(int number)
+static void u300_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
 {
-	if (number >= 0 &&
-	    number < (U300_GPIO_NUM_PORTS * U300_GPIO_PINS_PER_PORT))
-		return 1;
-	return 0;
-}
-EXPORT_SYMBOL(gpio_is_valid);
+	struct u300_gpio *gpio = to_u300_gpio(chip);
+	unsigned long flags;
+	u32 val;
 
-int gpio_request(unsigned gpio, const char *label)
-{
-	if (gpio_pin[gpio].users)
-		return -EINVAL;
-	else
-		gpio_pin[gpio].users++;
+	local_irq_save(flags);
 
-	gpio_users++;
+	val = readl(U300_PIN_REG(offset, dor));
+	if (value)
+		writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, dor));
+	else
+		writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, dor));
 
-	return 0;
+	local_irq_restore(flags);
 }
-EXPORT_SYMBOL(gpio_request);
 
-void gpio_free(unsigned gpio)
+static int u300_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
 {
-	gpio_users--;
-	gpio_pin[gpio].users--;
-	if (unlikely(gpio_pin[gpio].users < 0)) {
-		dev_warn(gpiodev, "warning: gpio#%d release mismatch\n",
-			 gpio);
-		gpio_pin[gpio].users = 0;
-	}
-
-	return;
-}
-EXPORT_SYMBOL(gpio_free);
+	struct u300_gpio *gpio = to_u300_gpio(chip);
+	unsigned long flags;
+	u32 val;
 
-/* This returns zero or nonzero */
-int gpio_get_value(unsigned gpio)
-{
-	return readl(virtbase + U300_GPIO_PXPDIR +
-	  PIN_TO_PORT(gpio) * U300_GPIO_PORTX_SPACING) & (1 << (gpio & 0x07));
+	local_irq_save(flags);
+	val = readl(U300_PIN_REG(offset, pcr));
+	/* Mask out this pin, note 2 bits per setting */
+	val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK << ((offset & 0x07) << 1));
+	writel(val, U300_PIN_REG(offset, pcr));
+	local_irq_restore(flags);
+	return 0;
 }
-EXPORT_SYMBOL(gpio_get_value);
 
-/*
- * We hope that the compiler will optimize away the unused branch
- * in case "value" is a constant
- */
-void gpio_set_value(unsigned gpio, int value)
+static int u300_gpio_direction_output(struct gpio_chip *chip, unsigned offset,
+				      int value)
 {
-	u32 val;
+	struct u300_gpio *gpio = to_u300_gpio(chip);
 	unsigned long flags;
+	u32 oldmode;
+	u32 val;
 
 	local_irq_save(flags);
-	if (value) {
-		/* set */
-		val = readl(virtbase + U300_GPIO_PXPDOR +
-		  PIN_TO_PORT(gpio) * U300_GPIO_PORTX_SPACING)
-		  & (1 << (gpio & 0x07));
-		writel(val | (1 << (gpio & 0x07)), virtbase +
-		  U300_GPIO_PXPDOR +
-		  PIN_TO_PORT(gpio) * U300_GPIO_PORTX_SPACING);
-	} else {
-		/* clear */
-		val = readl(virtbase + U300_GPIO_PXPDOR +
-		  PIN_TO_PORT(gpio) * U300_GPIO_PORTX_SPACING)
-		  & (1 << (gpio & 0x07));
-		writel(val & ~(1 << (gpio & 0x07)), virtbase +
-		  U300_GPIO_PXPDOR +
-		  PIN_TO_PORT(gpio) * U300_GPIO_PORTX_SPACING);
+	val = readl(U300_PIN_REG(offset, pcr));
+	/*
+	 * Drive mode must be set by the special mode set function, set
+	 * push/pull mode by default if no mode has been selected.
+	 */
+	oldmode = val & (U300_GPIO_PXPCR_PIN_MODE_MASK <<
+			 ((offset & 0x07) << 1));
+	/* mode = 0 means input, else some mode is already set */
+	if (oldmode == 0) {
+		val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK <<
+			 ((offset & 0x07) << 1));
+		val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL
+			<< ((offset & 0x07) << 1));
+		writel(val, U300_PIN_REG(offset, pcr));
 	}
+	u300_gpio_set(chip, offset, value);
 	local_irq_restore(flags);
+	return 0;
 }
-EXPORT_SYMBOL(gpio_set_value);
 
-int gpio_direction_input(unsigned gpio)
+static int u300_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
 {
+	struct u300_gpio *gpio = to_u300_gpio(chip);
+	int retirq = gpio->irq_base + offset;
+
+	dev_dbg(gpio->dev, "request IRQ for GPIO %d, return %d\n", offset,
+		retirq);
+	return retirq;
+}
+
+static int u300_gpio_config(struct gpio_chip *chip, unsigned offset,
+		     u16 param, unsigned long *data)
+{
+	struct u300_gpio *gpio = to_u300_gpio(chip);
 	unsigned long flags;
 	u32 val;
 
-	if (gpio > U300_GPIO_MAX)
-		return -EINVAL;
-
 	local_irq_save(flags);
-	val = readl(virtbase + U300_GPIO_PXPCR + PIN_TO_PORT(gpio) *
-				U300_GPIO_PORTX_SPACING);
-	/* Mask out this pin*/
-	val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK << ((gpio & 0x07) << 1));
-	/* This is not needed since it sets the bits to zero.*/
-	/* val |= (U300_GPIO_PXPCR_PIN_MODE_INPUT << (gpio*2)); */
-	writel(val, virtbase + U300_GPIO_PXPCR + PIN_TO_PORT(gpio) *
-				U300_GPIO_PORTX_SPACING);
+	switch (param) {
+	case GPIO_U300_CONFIG_BIAS_UNKNOWN:
+	case GPIO_U300_CONFIG_BIAS_FLOAT:
+		val = readl(U300_PIN_REG(offset, per));
+		writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, per));
+		break;
+	case GPIO_U300_CONFIG_BIAS_PULL_UP:
+		val = readl(U300_PIN_REG(offset, per));
+		writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, per));
+		break;
+	case GPIO_U300_CONFIG_DRIVE_PUSH_PULL:
+		val = readl(U300_PIN_REG(offset, pcr));
+		val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK
+			 << ((offset & 0x07) << 1));
+		val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL
+			<< ((offset & 0x07) << 1));
+		writel(val, U300_PIN_REG(offset, pcr));
+		break;
+	case GPIO_U300_CONFIG_DRIVE_OPEN_DRAIN:
+		val = readl(U300_PIN_REG(offset, pcr));
+		val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK
+			 << ((offset & 0x07) << 1));
+		val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN
+			<< ((offset & 0x07) << 1));
+		writel(val, U300_PIN_REG(offset, pcr));
+		break;
+	case GPIO_U300_CONFIG_DRIVE_OPEN_SOURCE:
+		val = readl(U300_PIN_REG(offset, pcr));
+		val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK
+			 << ((offset & 0x07) << 1));
+		val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE
+			<< ((offset & 0x07) << 1));
+		writel(val, U300_PIN_REG(offset, pcr));
+		break;
+	default:
+		local_irq_restore(flags);
+		dev_err(gpio->dev, "illegal configuration requested\n");
+		return -EINVAL;
+	}
 	local_irq_restore(flags);
 	return 0;
 }
-EXPORT_SYMBOL(gpio_direction_input);
 
-int gpio_direction_output(unsigned gpio, int value)
+static struct gpio_chip u300_gpio_chip = {
+	.label			= "u300-gpio-chip",
+	.owner			= THIS_MODULE,
+	.get			= u300_gpio_get,
+	.set			= u300_gpio_set,
+	.direction_input	= u300_gpio_direction_input,
+	.direction_output	= u300_gpio_direction_output,
+	.to_irq			= u300_gpio_to_irq,
+};
+
+static void u300_toggle_trigger(struct u300_gpio *gpio, unsigned offset)
 {
-	unsigned long flags;
 	u32 val;
 
-	if (gpio > U300_GPIO_MAX)
-		return -EINVAL;
-
-	local_irq_save(flags);
-	val = readl(virtbase + U300_GPIO_PXPCR + PIN_TO_PORT(gpio) *
-				U300_GPIO_PORTX_SPACING);
-	/* Mask out this pin */
-	val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK << ((gpio & 0x07) << 1));
-	/*
-	 * FIXME: configure for push/pull, open drain or open source per pin
-	 * in setup. The current driver will only support push/pull.
-	 */
-	val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL
-			<< ((gpio & 0x07) << 1));
-	writel(val, virtbase + U300_GPIO_PXPCR + PIN_TO_PORT(gpio) *
-				U300_GPIO_PORTX_SPACING);
-	gpio_set_value(gpio, value);
-	local_irq_restore(flags);
-	return 0;
+	val = readl(U300_PIN_REG(offset, icr));
+	/* Set mode depending on state */
+	if (u300_gpio_get(&gpio->chip, offset)) {
+		/* High now, let's trigger on falling edge next then */
+		writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, icr));
+		dev_dbg(gpio->dev, "next IRQ on falling edge on pin %d\n",
+			offset);
+	} else {
+		/* Low now, let's trigger on rising edge next then */
+		writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, icr));
+		dev_dbg(gpio->dev, "next IRQ on rising edge on pin %d\n",
+			offset);
+	}
 }
-EXPORT_SYMBOL(gpio_direction_output);
 
-/*
- * Enable an IRQ, edge is rising edge (!= 0) or falling edge (==0).
- */
-void enable_irq_on_gpio_pin(unsigned gpio, int edge)
+static int u300_gpio_irq_type(struct irq_data *d, unsigned trigger)
 {
+	struct u300_gpio_port *port = irq_data_get_irq_chip_data(d);
+	struct u300_gpio *gpio = port->gpio;
+	int offset = d->irq - gpio->irq_base;
 	u32 val;
-	unsigned long flags;
-	local_irq_save(flags);
 
-	val = readl(virtbase + U300_GPIO_PXIEN + PIN_TO_PORT(gpio) *
-				U300_GPIO_PORTX_SPACING);
-	val |= (1 << (gpio & 0x07));
-	writel(val, virtbase + U300_GPIO_PXIEN + PIN_TO_PORT(gpio) *
-				U300_GPIO_PORTX_SPACING);
-	val = readl(virtbase + U300_GPIO_PXICR + PIN_TO_PORT(gpio) *
-				U300_GPIO_PORTX_SPACING);
-	if (edge)
-		val |= (1 << (gpio & 0x07));
-	else
-		val &= ~(1 << (gpio & 0x07));
-	writel(val, virtbase + U300_GPIO_PXICR + PIN_TO_PORT(gpio) *
-				U300_GPIO_PORTX_SPACING);
-	local_irq_restore(flags);
+	if ((trigger & IRQF_TRIGGER_RISING) &&
+	    (trigger & IRQF_TRIGGER_FALLING)) {
+		/*
+		 * The GPIO block can only trigger on falling OR rising edges,
+		 * not both. So we need to toggle the mode whenever the pin
+		 * goes from one state to the other with a special state flag
+		 */
+		dev_dbg(gpio->dev,
+			"trigger on both rising and falling edge on pin %d\n",
+			offset);
+		port->toggle_edge_mode |= U300_PIN_BIT(offset);
+		u300_toggle_trigger(gpio, offset);
+	} else if (trigger & IRQF_TRIGGER_RISING) {
+		dev_dbg(gpio->dev, "trigger on rising edge on pin %d\n",
+			offset);
+		val = readl(U300_PIN_REG(offset, icr));
+		writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, icr));
+		port->toggle_edge_mode &= ~U300_PIN_BIT(offset);
+	} else if (trigger & IRQF_TRIGGER_FALLING) {
+		dev_dbg(gpio->dev, "trigger on falling edge on pin %d\n",
+			offset);
+		val = readl(U300_PIN_REG(offset, icr));
+		writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, icr));
+		port->toggle_edge_mode &= ~U300_PIN_BIT(offset);
+	}
+
+	return 0;
 }
-EXPORT_SYMBOL(enable_irq_on_gpio_pin);
 
-void disable_irq_on_gpio_pin(unsigned gpio)
+static void u300_gpio_irq_enable(struct irq_data *d)
 {
+	struct u300_gpio_port *port = irq_data_get_irq_chip_data(d);
+	struct u300_gpio *gpio = port->gpio;
+	int offset = d->irq - gpio->irq_base;
 	u32 val;
 	unsigned long flags;
 
 	local_irq_save(flags);
-	val = readl(virtbase + U300_GPIO_PXIEN + PIN_TO_PORT(gpio) *
-				U300_GPIO_PORTX_SPACING);
-	val &= ~(1 << (gpio & 0x07));
-	writel(val, virtbase + U300_GPIO_PXIEN + PIN_TO_PORT(gpio) *
-				U300_GPIO_PORTX_SPACING);
+	val = readl(U300_PIN_REG(offset, ien));
+	writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, ien));
 	local_irq_restore(flags);
 }
-EXPORT_SYMBOL(disable_irq_on_gpio_pin);
 
-/* Enable (value == 0) or disable (value == 1) internal pullup */
-void gpio_pullup(unsigned gpio, int value)
+static void u300_gpio_irq_disable(struct irq_data *d)
 {
+	struct u300_gpio_port *port = irq_data_get_irq_chip_data(d);
+	struct u300_gpio *gpio = port->gpio;
+	int offset = d->irq - gpio->irq_base;
 	u32 val;
 	unsigned long flags;
 
 	local_irq_save(flags);
-	if (value) {
-		val = readl(virtbase + U300_GPIO_PXPER + PIN_TO_PORT(gpio) *
-					U300_GPIO_PORTX_SPACING);
-		writel(val | (1 << (gpio & 0x07)), virtbase + U300_GPIO_PXPER +
-				PIN_TO_PORT(gpio) * U300_GPIO_PORTX_SPACING);
-	} else {
-		val = readl(virtbase + U300_GPIO_PXPER + PIN_TO_PORT(gpio) *
-					U300_GPIO_PORTX_SPACING);
-		writel(val & ~(1 << (gpio & 0x07)), virtbase + U300_GPIO_PXPER +
-				PIN_TO_PORT(gpio) * U300_GPIO_PORTX_SPACING);
-	}
+	val = readl(U300_PIN_REG(offset, ien));
+	writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, ien));
 	local_irq_restore(flags);
 }
-EXPORT_SYMBOL(gpio_pullup);
 
-static irqreturn_t gpio_irq_handler(int irq, void *dev_id)
+static struct irq_chip u300_gpio_irqchip = {
+	.name			= "u300-gpio-irqchip",
+	.irq_enable		= u300_gpio_irq_enable,
+	.irq_disable		= u300_gpio_irq_disable,
+	.irq_set_type		= u300_gpio_irq_type,
+
+};
+
+static void u300_gpio_irq_handler(unsigned irq, struct irq_desc *desc)
 {
-	struct u300_gpio_port *port = dev_id;
-	u32 val;
-	int pin;
+	struct u300_gpio_port *port = irq_get_handler_data(irq);
+	struct u300_gpio *gpio = port->gpio;
+	int pinoffset = port->number << 3; /* get the right stride */
+	unsigned long val;
 
+	desc->irq_data.chip->irq_ack(&desc->irq_data);
 	/* Read event register */
-	val = readl(virtbase + U300_GPIO_PXIEV + port->number *
-				U300_GPIO_PORTX_SPACING);
-	/* Mask with enable register */
-	val &= readl(virtbase + U300_GPIO_PXIEV + port->number *
-				U300_GPIO_PORTX_SPACING);
+	val = readl(U300_PIN_REG(pinoffset, iev));
 	/* Mask relevant bits */
-	val &= U300_GPIO_PXIEV_ALL_IRQ_EVENT_MASK;
+	val &= 0xFFU; /* 8 bits per port */
 	/* ACK IRQ (clear event) */
-	writel(val, virtbase + U300_GPIO_PXIEV + port->number *
-				U300_GPIO_PORTX_SPACING);
-	/* Print message */
-	while (val != 0) {
-		unsigned gpio;
-
-		pin = __ffs(val);
-		/* mask off this pin */
-		val &= ~(1 << pin);
-		gpio = (port->number << 3) + pin;
-
-		if (gpio_pin[gpio].callback)
-			(void)gpio_pin[gpio].callback(gpio_pin[gpio].data);
-		else
-			dev_dbg(gpiodev, "stray GPIO IRQ on line %d\n",
-			       gpio);
+	writel(val, U300_PIN_REG(pinoffset, iev));
+
+	/* Call IRQ handler */
+	if (val != 0) {
+		int irqoffset;
+
+		for_each_set_bit(irqoffset, &val, U300_GPIO_PINS_PER_PORT) {
+			int pin_irq = gpio->irq_base + (port->number << 3)
+				+ irqoffset;
+			int offset = pinoffset + irqoffset;
+
+			dev_dbg(gpio->dev, "GPIO IRQ %d on pin %d\n",
+				pin_irq, offset);
+			generic_handle_irq(pin_irq);
+			/*
+			 * Triggering IRQ on both rising and falling edge
+			 * needs mockery
+			 */
+			if (port->toggle_edge_mode & U300_PIN_BIT(offset))
+				u300_toggle_trigger(gpio, offset);
+		}
 	}
-	return IRQ_HANDLED;
+
+	desc->irq_data.chip->irq_unmask(&desc->irq_data);
 }
 
-static void gpio_set_initial_values(void)
+static void __init u300_gpio_init_pin(struct u300_gpio *gpio,
+				      int offset,
+				      const struct u300_gpio_confdata *conf)
 {
-#ifdef U300_COH901571_3
-	int i, j;
-	unsigned long flags;
-	u32 val;
+	/* Set mode: input or output */
+	if (conf->output) {
+		u300_gpio_direction_output(&gpio->chip, offset, conf->outval);
 
-	/* Write default values to all pins */
-	for (i = 0; i < U300_GPIO_NUM_PORTS; i++) {
-		val = 0;
-		for (j = 0; j < 8; j++)
-			val |= (u32) (u300_gpio_config[i][j].default_output_value != DEFAULT_OUTPUT_LOW) << j;
-		local_irq_save(flags);
-		writel(val, virtbase + U300_GPIO_PXPDOR + i * U300_GPIO_PORTX_SPACING);
-		local_irq_restore(flags);
+		/* Deactivate bias mode for output */
+		u300_gpio_config(&gpio->chip, offset,
+				 GPIO_U300_CONFIG_BIAS_FLOAT,
+				 NULL);
+
+		/* Set drive mode for output */
+		u300_gpio_config(&gpio->chip, offset,
+				 GPIO_U300_CONFIG_DRIVE_PUSH_PULL, NULL);
+
+		dev_dbg(gpio->dev, "set up pin %d as output, value: %d\n",
+			offset, conf->outval);
+	} else {
+		u300_gpio_direction_input(&gpio->chip, offset);
+
+		/* Always set output low on input pins */
+		u300_gpio_set(&gpio->chip, offset, 0);
+
+		/* Set bias mode for input */
+		u300_gpio_config(&gpio->chip, offset, conf->bias_mode, NULL);
+
+		dev_dbg(gpio->dev, "set up pin %d as input, bias: %04x\n",
+			offset, conf->bias_mode);
 	}
+}
 
-	/*
-	 * Put all pins that are set to either 'GPIO_OUT' or 'GPIO_NOT_USED'
-	 * to output and 'GPIO_IN' to input for each port. And initialize
-	 * default value on outputs.
-	 */
-	for (i = 0; i < U300_GPIO_NUM_PORTS; i++) {
-		for (j = 0; j < U300_GPIO_PINS_PER_PORT; j++) {
-			local_irq_save(flags);
-			val = readl(virtbase + U300_GPIO_PXPCR +
-					 i * U300_GPIO_PORTX_SPACING);
-			/* Mask out this pin */
-			val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK << (j << 1));
-
-			if (u300_gpio_config[i][j].pin_usage != GPIO_IN)
-				val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL << (j << 1));
-			writel(val, virtbase + U300_GPIO_PXPCR +
-					 i * U300_GPIO_PORTX_SPACING);
-			local_irq_restore(flags);
+static void __init u300_gpio_init_coh901571(struct u300_gpio *gpio,
+				     struct u300_gpio_platform *plat)
+{
+	int i, j;
+
+	/* Write default config and values to all pins */
+	for (i = 0; i < plat->ports; i++) {
+		for (j = 0; j < 8; j++) {
+			const struct u300_gpio_confdata *conf;
+			int offset = (i*8) + j;
+
+			if (plat->variant == U300_GPIO_COH901571_3_BS335)
+				conf = &bs335_gpio_config[i][j];
+			else if (plat->variant == U300_GPIO_COH901571_3_BS365)
+				conf = &bs365_gpio_config[i][j];
+			else
+				break;
+
+			u300_gpio_init_pin(gpio, offset, conf);
 		}
 	}
+}
 
-	/* Enable or disable the internal pull-ups in the GPIO ASIC block */
-	for (i = 0; i < U300_GPIO_MAX; i++) {
-		val = 0;
-		for (j = 0; j < 8; j++)
-			val |= (u32)((u300_gpio_config[i][j].pull_up == DISABLE_PULL_UP) << j);
-		local_irq_save(flags);
-		writel(val, virtbase + U300_GPIO_PXPER + i * U300_GPIO_PORTX_SPACING);
-		local_irq_restore(flags);
+static inline void u300_gpio_free_ports(struct u300_gpio *gpio)
+{
+	struct u300_gpio_port *port;
+	struct list_head *p, *n;
+
+	list_for_each_safe(p, n, &gpio->port_list) {
+		port = list_entry(p, struct u300_gpio_port, node);
+		list_del(&port->node);
+		free_irq(port->irq, port);
+		kfree(port);
 	}
-#endif
 }
 
-static int __init gpio_probe(struct platform_device *pdev)
+static int __init u300_gpio_probe(struct platform_device *pdev)
 {
-	u32 val;
+	struct u300_gpio_platform *plat = dev_get_platdata(&pdev->dev);
+	struct u300_gpio *gpio;
 	int err = 0;
+	int portno;
+	u32 val;
+	u32 ifr;
 	int i;
-	int num_irqs;
 
-	gpiodev = &pdev->dev;
-	memset(gpio_pin, 0, sizeof(gpio_pin));
+	gpio = kzalloc(sizeof(struct u300_gpio), GFP_KERNEL);
+	if (gpio == NULL) {
+		dev_err(&pdev->dev, "failed to allocate memory\n");
+		return -ENOMEM;
+	}
+
+	gpio->chip = u300_gpio_chip;
+	gpio->chip.ngpio = plat->ports * U300_GPIO_PINS_PER_PORT;
+	gpio->irq_base = plat->gpio_irq_base;
+	gpio->chip.dev = &pdev->dev;
+	gpio->chip.base = plat->gpio_base;
+	gpio->dev = &pdev->dev;
 
 	/* Get GPIO clock */
-	clk = clk_get(&pdev->dev, NULL);
-	if (IS_ERR(clk)) {
-		err = PTR_ERR(clk);
-		dev_err(gpiodev, "could not get GPIO clock\n");
+	gpio->clk = clk_get(gpio->dev, NULL);
+	if (IS_ERR(gpio->clk)) {
+		err = PTR_ERR(gpio->clk);
+		dev_err(gpio->dev, "could not get GPIO clock\n");
 		goto err_no_clk;
 	}
-	err = clk_enable(clk);
+	err = clk_enable(gpio->clk);
 	if (err) {
-		dev_err(gpiodev, "could not enable GPIO clock\n");
+		dev_err(gpio->dev, "could not enable GPIO clock\n");
 		goto err_no_clk_enable;
 	}
 
-	memres = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (!memres)
+	gpio->memres = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!gpio->memres) {
+		dev_err(gpio->dev, "could not get GPIO memory resource\n");
+		err = -ENODEV;
 		goto err_no_resource;
+	}
 
-	if (!request_mem_region(memres->start, resource_size(memres),
+	if (!request_mem_region(gpio->memres->start,
+				resource_size(gpio->memres),
 				"GPIO Controller")) {
 		err = -ENODEV;
 		goto err_no_ioregion;
 	}
 
-	virtbase = ioremap(memres->start, resource_size(memres));
-	if (!virtbase) {
+	gpio->base = ioremap(gpio->memres->start, resource_size(gpio->memres));
+	if (!gpio->base) {
 		err = -ENOMEM;
 		goto err_no_ioremap;
 	}
-	dev_info(gpiodev, "remapped 0x%08x to %p\n",
-		 memres->start, virtbase);
-
-#ifdef U300_COH901335
-	dev_info(gpiodev, "initializing GPIO Controller COH 901 335\n");
-	/* Turn on the GPIO block */
-	writel(U300_GPIO_CR_BLOCK_CLOCK_ENABLE, virtbase + U300_GPIO_CR);
-#endif
-
-#ifdef U300_COH901571_3
-	dev_info(gpiodev, "initializing GPIO Controller COH 901 571/3\n");
-	val = readl(virtbase + U300_GPIO_CR);
-	dev_info(gpiodev, "COH901571/3 block version: %d, " \
-	       "number of cores: %d\n",
-	       ((val & 0x0000FE00) >> 9),
-	       ((val & 0x000001FC) >> 2));
-	writel(U300_GPIO_CR_BLOCK_CLKRQ_ENABLE, virtbase + U300_GPIO_CR);
-#endif
-
-	gpio_set_initial_values();
-
-	for (num_irqs = 0 ; num_irqs < U300_GPIO_NUM_PORTS; num_irqs++) {
-
-		gpio_ports[num_irqs].irq =
-			platform_get_irq_byname(pdev,
-						gpio_ports[num_irqs].name);
-
-		err = request_irq(gpio_ports[num_irqs].irq,
-				  gpio_irq_handler, IRQF_DISABLED,
-				  gpio_ports[num_irqs].name,
-				  &gpio_ports[num_irqs]);
-		if (err) {
-			dev_err(gpiodev, "cannot allocate IRQ for %s!\n",
-				gpio_ports[num_irqs].name);
-			goto err_no_irq;
+
+	if (plat->variant == U300_GPIO_COH901335) {
+		dev_info(gpio->dev,
+			 "initializing GPIO Controller COH 901 335\n");
+		gpio->stride = U300_335_PORT_STRIDE;
+		gpio->pcr = U300_335_PXPCR;
+		gpio->dor = U300_335_PXPDOR;
+		gpio->dir = U300_335_PXPDIR;
+		gpio->per = U300_335_PXPER;
+		gpio->icr = U300_335_PXICR;
+		gpio->ien = U300_335_PXIEN;
+		gpio->iev = U300_335_PXIEV;
+		ifr = U300_335_PXIFR;
+
+		/* Turn on the GPIO block */
+		writel(U300_335_CR_BLOCK_CLOCK_ENABLE,
+		       gpio->base + U300_335_CR);
+	} else if (plat->variant == U300_GPIO_COH901571_3_BS335 ||
+		   plat->variant == U300_GPIO_COH901571_3_BS365) {
+		dev_info(gpio->dev,
+			 "initializing GPIO Controller COH 901 571/3\n");
+		gpio->stride = U300_571_PORT_STRIDE;
+		gpio->pcr = U300_571_PXPCR;
+		gpio->dor = U300_571_PXPDOR;
+		gpio->dir = U300_571_PXPDIR;
+		gpio->per = U300_571_PXPER;
+		gpio->icr = U300_571_PXICR;
+		gpio->ien = U300_571_PXIEN;
+		gpio->iev = U300_571_PXIEV;
+		ifr = U300_571_PXIFR;
+
+		val = readl(gpio->base + U300_571_CR);
+		dev_info(gpio->dev, "COH901571/3 block version: %d, " \
+			 "number of cores: %d totalling %d pins\n",
+			 ((val & 0x000001FC) >> 2),
+			 ((val & 0x0000FE00) >> 9),
+			 ((val & 0x0000FE00) >> 9) * 8);
+		writel(U300_571_CR_BLOCK_CLKRQ_ENABLE,
+		       gpio->base + U300_571_CR);
+		u300_gpio_init_coh901571(gpio, plat);
+	} else {
+		dev_err(gpio->dev, "unknown block variant\n");
+		err = -ENODEV;
+		goto err_unknown_variant;
+	}
+
+	/* Add each port with its IRQ separately */
+	INIT_LIST_HEAD(&gpio->port_list);
+	for (portno = 0 ; portno < plat->ports; portno++) {
+		struct u300_gpio_port *port =
+			kmalloc(sizeof(struct u300_gpio_port), GFP_KERNEL);
+
+		if (!port) {
+			dev_err(gpio->dev, "out of memory\n");
+			err = -ENOMEM;
+			goto err_no_port;
 		}
-		/* Turns off PortX_irq_force */
-		writel(0x0, virtbase + U300_GPIO_PXIFR +
-				 num_irqs * U300_GPIO_PORTX_SPACING);
+
+		snprintf(port->name, 8, "gpio%d", portno);
+		port->number = portno;
+		port->gpio = gpio;
+
+		port->irq = platform_get_irq_byname(pdev,
+						    port->name);
+
+		dev_dbg(gpio->dev, "register IRQ %d for %s\n", port->irq,
+			port->name);
+
+		irq_set_chained_handler(port->irq, u300_gpio_irq_handler);
+		irq_set_handler_data(port->irq, port);
+
+		/* For each GPIO pin set the unique IRQ handler */
+		for (i = 0; i < U300_GPIO_PINS_PER_PORT; i++) {
+			int irqno = gpio->irq_base + (portno << 3) + i;
+
+			dev_dbg(gpio->dev, "handler for IRQ %d on %s\n",
+				irqno, port->name);
+			irq_set_chip_and_handler(irqno, &u300_gpio_irqchip,
+						 handle_simple_irq);
+			set_irq_flags(irqno, IRQF_VALID);
+			irq_set_chip_data(irqno, port);
+		}
+
+		/* Turns off irq force (test register) for this port */
+		writel(0x0, gpio->base + portno * gpio->stride + ifr);
+
+		list_add_tail(&port->node, &gpio->port_list);
 	}
+	dev_dbg(gpio->dev, "initialized %d GPIO ports\n", portno);
+
+	err = gpiochip_add(&gpio->chip);
+	if (err) {
+		dev_err(gpio->dev, "unable to add gpiochip: %d\n", err);
+		goto err_no_chip;
+	}
+
+	platform_set_drvdata(pdev, gpio);
 
 	return 0;
 
- err_no_irq:
-	for (i = 0; i < num_irqs; i++)
-		free_irq(gpio_ports[i].irq, &gpio_ports[i]);
-	iounmap(virtbase);
- err_no_ioremap:
-	release_mem_region(memres->start, resource_size(memres));
- err_no_ioregion:
- err_no_resource:
-	clk_disable(clk);
- err_no_clk_enable:
-	clk_put(clk);
- err_no_clk:
-	dev_info(gpiodev, "module ERROR:%d\n", err);
+err_no_chip:
+err_no_port:
+	u300_gpio_free_ports(gpio);
+err_unknown_variant:
+	iounmap(gpio->base);
+err_no_ioremap:
+	release_mem_region(gpio->memres->start, resource_size(gpio->memres));
+err_no_ioregion:
+err_no_resource:
+	clk_disable(gpio->clk);
+err_no_clk_enable:
+	clk_put(gpio->clk);
+err_no_clk:
+	kfree(gpio);
+	dev_info(&pdev->dev, "module ERROR:%d\n", err);
 	return err;
 }
 
-static int __exit gpio_remove(struct platform_device *pdev)
+static int __exit u300_gpio_remove(struct platform_device *pdev)
 {
-	int i;
+	struct u300_gpio_platform *plat = dev_get_platdata(&pdev->dev);
+	struct u300_gpio *gpio = platform_get_drvdata(pdev);
+	int err;
 
 	/* Turn off the GPIO block */
-	writel(0x00000000U, virtbase + U300_GPIO_CR);
-	for (i = 0 ; i < U300_GPIO_NUM_PORTS; i++)
-		free_irq(gpio_ports[i].irq, &gpio_ports[i]);
-	iounmap(virtbase);
-	release_mem_region(memres->start, resource_size(memres));
-	clk_disable(clk);
-	clk_put(clk);
+	if (plat->variant == U300_GPIO_COH901335)
+		writel(0x00000000U, gpio->base + U300_335_CR);
+	if (plat->variant == U300_GPIO_COH901571_3_BS335 ||
+	    plat->variant == U300_GPIO_COH901571_3_BS365)
+		writel(0x00000000U, gpio->base + U300_571_CR);
+
+	err = gpiochip_remove(&gpio->chip);
+	if (err < 0) {
+		dev_err(gpio->dev, "unable to remove gpiochip: %d\n", err);
+		return err;
+	}
+	u300_gpio_free_ports(gpio);
+	iounmap(gpio->base);
+	release_mem_region(gpio->memres->start,
+			   resource_size(gpio->memres));
+	clk_disable(gpio->clk);
+	clk_put(gpio->clk);
+	platform_set_drvdata(pdev, NULL);
+	kfree(gpio);
 	return 0;
 }
 
-static struct platform_driver gpio_driver = {
+static struct platform_driver u300_gpio_driver = {
 	.driver		= {
 		.name	= "u300-gpio",
 	},
-	.remove		= __exit_p(gpio_remove),
+	.remove		= __exit_p(u300_gpio_remove),
 };
 
 
 static int __init u300_gpio_init(void)
 {
-	return platform_driver_probe(&gpio_driver, gpio_probe);
+	return platform_driver_probe(&u300_gpio_driver, u300_gpio_probe);
 }
 
 static void __exit u300_gpio_exit(void)
 {
-	platform_driver_unregister(&gpio_driver);
+	platform_driver_unregister(&u300_gpio_driver);
 }
 
 arch_initcall(u300_gpio_init);
 module_exit(u300_gpio_exit);
 
 MODULE_AUTHOR("Linus Walleij <linus.walleij@stericsson.com>");
-
-#ifdef U300_COH901571_3
-MODULE_DESCRIPTION("ST-Ericsson AB COH 901 571/3 GPIO driver");
-#endif
-
-#ifdef U300_COH901335
-MODULE_DESCRIPTION("ST-Ericsson AB COH 901 335 GPIO driver");
-#endif
-
+MODULE_DESCRIPTION("ST-Ericsson AB COH 901 335/COH 901 571/3 GPIO driver");
 MODULE_LICENSE("GPL");
diff --git a/drivers/i2c/busses/i2c-ixp2000.c b/drivers/i2c/busses/i2c-ixp2000.c
index 5d8aed5ec21b..c01e9519f6c1 100644
--- a/drivers/i2c/busses/i2c-ixp2000.c
+++ b/drivers/i2c/busses/i2c-ixp2000.c
@@ -35,7 +35,7 @@
 #include <linux/slab.h>
 
 #include <mach/hardware.h>	/* Pick up IXP2000-specific bits */
-#include <mach/gpio.h>
+#include <mach/gpio-ixp2000.h>
 
 static inline int ixp2000_scl_pin(void *data)
 {
diff --git a/drivers/ide/at91_ide.c b/drivers/ide/at91_ide.c
index 000a78e5246c..6dede8f366c5 100644
--- a/drivers/ide/at91_ide.c
+++ b/drivers/ide/at91_ide.c
@@ -28,7 +28,7 @@
 #include <linux/platform_device.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
 #include <mach/at91sam9_smc.h>
 
 #define DRV_NAME "at91_ide"
diff --git a/drivers/input/keyboard/omap-keypad.c b/drivers/input/keyboard/omap-keypad.c
index 33d0bdc837c0..323bcdfff248 100644
--- a/drivers/input/keyboard/omap-keypad.c
+++ b/drivers/input/keyboard/omap-keypad.c
@@ -35,7 +35,7 @@
 #include <linux/mutex.h>
 #include <linux/errno.h>
 #include <linux/slab.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
 #include <plat/keypad.h>
 #include <plat/menelaus.h>
 #include <asm/irq.h>
diff --git a/drivers/mfd/menelaus.c b/drivers/mfd/menelaus.c
index 9cee8e7f0bcb..af5d9d061371 100644
--- a/drivers/mfd/menelaus.c
+++ b/drivers/mfd/menelaus.c
@@ -44,7 +44,7 @@
 
 #include <asm/mach/irq.h>
 
-#include <mach/gpio.h>
+#include <asm/gpio.h>
 #include <plat/menelaus.h>
 
 #define DRIVER_NAME			"menelaus"
diff --git a/drivers/mmc/host/omap.c b/drivers/mmc/host/omap.c
index a6c329040140..2dba999caf2c 100644
--- a/drivers/mmc/host/omap.c
+++ b/drivers/mmc/host/omap.c
@@ -33,7 +33,7 @@
 
 #include <plat/board.h>
 #include <plat/mmc.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
 #include <plat/dma.h>
 #include <plat/mux.h>
 #include <plat/fpga.h>
diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c
index 18b0bd31de78..21b00cefae63 100644
--- a/drivers/mmc/host/sdhci-tegra.c
+++ b/drivers/mmc/host/sdhci-tegra.c
@@ -21,7 +21,9 @@
 #include <linux/mmc/card.h>
 #include <linux/mmc/host.h>
 
-#include <mach/gpio.h>
+#include <asm/gpio.h>
+
+#include <mach/gpio-tegra.h>
 #include <mach/sdhci.h>
 
 #include "sdhci-pltfm.h"
diff --git a/drivers/mtd/nand/ams-delta.c b/drivers/mtd/nand/ams-delta.c
index 78017eb9318e..9e6b498c9beb 100644
--- a/drivers/mtd/nand/ams-delta.c
+++ b/drivers/mtd/nand/ams-delta.c
@@ -26,7 +26,7 @@
 #include <asm/io.h>
 #include <mach/hardware.h>
 #include <asm/sizes.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
 #include <plat/board-ams-delta.h>
 
 /*
diff --git a/drivers/mtd/onenand/omap2.c b/drivers/mtd/onenand/omap2.c
index a916dec29215..6a1d6d9a2df9 100644
--- a/drivers/mtd/onenand/omap2.c
+++ b/drivers/mtd/onenand/omap2.c
@@ -40,7 +40,7 @@
 #include <asm/mach/flash.h>
 #include <plat/gpmc.h>
 #include <plat/onenand.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
 
 #include <plat/dma.h>
 
diff --git a/drivers/net/arm/at91_ether.c b/drivers/net/arm/at91_ether.c
index 29dc43523cec..48b4ec121f7f 100644
--- a/drivers/net/arm/at91_ether.c
+++ b/drivers/net/arm/at91_ether.c
@@ -35,7 +35,7 @@
 #include <asm/mach-types.h>
 
 #include <mach/at91rm9200_emac.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
 #include <mach/board.h>
 
 #include "at91_ether.h"
diff --git a/drivers/pcmcia/pxa2xx_vpac270.c b/drivers/pcmcia/pxa2xx_vpac270.c
index e956f659089a..66ab92cf3105 100644
--- a/drivers/pcmcia/pxa2xx_vpac270.c
+++ b/drivers/pcmcia/pxa2xx_vpac270.c
@@ -17,7 +17,7 @@
 
 #include <asm/mach-types.h>
 
-#include <mach/gpio.h>
+#include <asm/gpio.h>
 #include <mach/vpac270.h>
 
 #include "soc_common.h"
diff --git a/drivers/spi/spi-atmel.c b/drivers/spi/spi-atmel.c
index 82dee9a6c0de..d3bff424286f 100644
--- a/drivers/spi/spi-atmel.c
+++ b/drivers/spi/spi-atmel.c
@@ -22,7 +22,7 @@
 
 #include <asm/io.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
 #include <mach/cpu.h>
 
 /* SPI register offsets */
diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index b922f5d2e61e..caba6730a943 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -46,7 +46,7 @@
 
 #ifdef CONFIG_ARM
 #include <mach/cpu.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
 #endif
 
 #define PDC_BUFFER_SIZE		512
diff --git a/drivers/usb/host/ohci-pnx4008.c b/drivers/usb/host/ohci-pnx4008.c
index 653d6a60edb5..d1b41933199e 100644
--- a/drivers/usb/host/ohci-pnx4008.c
+++ b/drivers/usb/host/ohci-pnx4008.c
@@ -26,7 +26,7 @@
 
 #include <mach/platform.h>
 #include <mach/irqs.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
 
 #define USB_CTRL	IO_ADDRESS(PNX4008_PWRMAN_BASE + 0x64)
 
diff --git a/drivers/usb/musb/davinci.c b/drivers/usb/musb/davinci.c
index 8bdf25a8b023..f9a3f62a83b5 100644
--- a/drivers/usb/musb/davinci.c
+++ b/drivers/usb/musb/davinci.c
@@ -35,7 +35,7 @@
 
 #include <mach/hardware.h>
 #include <mach/memory.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
 #include <mach/cputype.h>
 
 #include <asm/mach-types.h>
diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
index 817ab60f7537..dda920623c6a 100644
--- a/drivers/video/atmel_lcdfb.c
+++ b/drivers/video/atmel_lcdfb.c
@@ -21,7 +21,7 @@
 
 #include <mach/board.h>
 #include <mach/cpu.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
 
 #include <video/atmel_lcdc.h>
 
diff --git a/drivers/video/omap/lcd_apollon.c b/drivers/video/omap/lcd_apollon.c
index 10459d8bd9a0..4b24f549f9b9 100644
--- a/drivers/video/omap/lcd_apollon.c
+++ b/drivers/video/omap/lcd_apollon.c
@@ -24,7 +24,7 @@
 #include <linux/module.h>
 #include <linux/platform_device.h>
 
-#include <mach/gpio.h>
+#include <asm/gpio.h>
 
 #include "omapfb.h"
 
diff --git a/drivers/video/omap/lcd_h3.c b/drivers/video/omap/lcd_h3.c
index 8df688748b5a..622ad839fd9d 100644
--- a/drivers/video/omap/lcd_h3.c
+++ b/drivers/video/omap/lcd_h3.c
@@ -23,7 +23,7 @@
 #include <linux/platform_device.h>
 #include <linux/i2c/tps65010.h>
 
-#include <mach/gpio.h>
+#include <asm/gpio.h>
 #include "omapfb.h"
 
 #define MODULE_NAME	"omapfb-lcd_h3"
diff --git a/drivers/video/omap/lcd_inn1610.c b/drivers/video/omap/lcd_inn1610.c
index 9fff86f67bde..12cc52a70f96 100644
--- a/drivers/video/omap/lcd_inn1610.c
+++ b/drivers/video/omap/lcd_inn1610.c
@@ -22,7 +22,7 @@
 #include <linux/module.h>
 #include <linux/platform_device.h>
 
-#include <mach/gpio.h>
+#include <asm/gpio.h>
 #include "omapfb.h"
 
 #define MODULE_NAME	"omapfb-lcd_h3"
diff --git a/drivers/video/omap/lcd_ldp.c b/drivers/video/omap/lcd_ldp.c
index 0f5952cae85e..062466402c0e 100644
--- a/drivers/video/omap/lcd_ldp.c
+++ b/drivers/video/omap/lcd_ldp.c
@@ -26,7 +26,7 @@
 #include <linux/delay.h>
 #include <linux/i2c/twl.h>
 
-#include <mach/gpio.h>
+#include <asm/gpio.h>
 #include <plat/mux.h>
 #include <asm/mach-types.h>
 
diff --git a/drivers/video/omap/lcd_osk.c b/drivers/video/omap/lcd_osk.c
index b87e8b83f29c..6f8d13c41202 100644
--- a/drivers/video/omap/lcd_osk.c
+++ b/drivers/video/omap/lcd_osk.c
@@ -23,7 +23,7 @@
 #include <linux/module.h>
 #include <linux/platform_device.h>
 
-#include <mach/gpio.h>
+#include <asm/gpio.h>
 #include <plat/mux.h>
 #include "omapfb.h"
 
diff --git a/drivers/video/omap/lcd_overo.c b/drivers/video/omap/lcd_overo.c
index 564933ffac6e..b8fd5b2ec29c 100644
--- a/drivers/video/omap/lcd_overo.c
+++ b/drivers/video/omap/lcd_overo.c
@@ -23,7 +23,7 @@
 #include <linux/platform_device.h>
 #include <linux/i2c/twl.h>
 
-#include <mach/gpio.h>
+#include <asm/gpio.h>
 #include <plat/mux.h>
 #include <asm/mach-types.h>
 
diff --git a/drivers/video/omap/lcd_palmtt.c b/drivers/video/omap/lcd_palmtt.c
index ff0e6d7ab3a2..b51b332e5a2b 100644
--- a/drivers/video/omap/lcd_palmtt.c
+++ b/drivers/video/omap/lcd_palmtt.c
@@ -29,7 +29,7 @@ GPIO13 - screen blanking
 #include <linux/module.h>
 #include <linux/io.h>
 
-#include <mach/gpio.h>
+#include <asm/gpio.h>
 #include "omapfb.h"
 
 static int palmtt_panel_init(struct lcd_panel *panel,
diff --git a/drivers/video/pnx4008/sdum.c b/drivers/video/pnx4008/sdum.c
index 5ec4f2d439c9..50e00395240f 100644
--- a/drivers/video/pnx4008/sdum.c
+++ b/drivers/video/pnx4008/sdum.c
@@ -30,7 +30,7 @@
 #include <linux/clk.h>
 #include <linux/gfp.h>
 #include <asm/uaccess.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
 
 #include "sdum.h"
 #include "fbcommon.h"