Merge tag 'tty-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull tty / serial driver updates from Greg KH:
 "Here is the big set of serial and tty driver updates for 6.3-rc1.

  Once again, Jiri and Ilpo have done a number of core vt and tty/serial
  layer cleanups that were much needed and appreciated. Other than that,
  it's just a bunch of little tty/serial driver updates:

   - qcom-geni-serial driver updates

   - liteuart driver updates

   - hvcs driver cleanups

   - n_gsm updates and additions for new features

   - more 8250 device support added

   - fpga/dfl update and additions

   - imx serial driver updates

   - fsl_lpuart updates

   - other tiny fixes and updates for serial drivers

  All of these have been in linux-next for a while with no reported
  problems"

* tag 'tty-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (143 commits)
  tty: n_gsm: add keep alive support
  serial: imx: remove a redundant check
  dt-bindings: serial: snps-dw-apb-uart: add dma & dma-names properties
  soc: qcom: geni-se: Move qcom-geni-se.h to linux/soc/qcom/geni-se.h
  tty: n_gsm: add TIOCMIWAIT support
  tty: n_gsm: add RING/CD control support
  tty: n_gsm: mark unusable ioctl structure fields accordingly
  serial: imx: get rid of registers shadowing
  serial: imx: refine local variables in rxint()
  serial: imx: stop using USR2 in FIFO reading loop
  serial: imx: remove redundant USR2 read from FIFO reading loop
  serial: imx: do not break from FIFO reading loop prematurely
  serial: imx: do not sysrq broken chars
  serial: imx: work-around for hardware RX flood
  serial: imx: factor-out common code to imx_uart_soft_reset()
  serial: 8250_pci1xxxx: Add power management functions to quad-uart driver
  serial: 8250_pci1xxxx: Add RS485 support to quad-uart driver
  serial: 8250_pci1xxxx: Add driver for quad-uart support
  serial: 8250_pci: Add serial8250_pci_setup_port definition in 8250_pcilib.c
  tty: pcn_uart: fix memory leak with using debugfs_lookup()
  ...

1 files changed, 7 insertions, 5 deletions

diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt
index 276a793168a6..8faec13961cd 100644
--- a/Documentation/admin-guide/kernel-parameters.txt
+++ b/Documentation/admin-guide/kernel-parameters.txt
@@ -1172,10 +1172,10 @@
 			specified, the serial port must already be setup and
 			configured.
 
-		uart[8250],io,<addr>[,options]
-		uart[8250],mmio,<addr>[,options]
-		uart[8250],mmio32,<addr>[,options]
-		uart[8250],mmio32be,<addr>[,options]
+		uart[8250],io,<addr>[,options[,uartclk]]
+		uart[8250],mmio,<addr>[,options[,uartclk]]
+		uart[8250],mmio32,<addr>[,options[,uartclk]]
+		uart[8250],mmio32be,<addr>[,options[,uartclk]]
 		uart[8250],0x<addr>[,options]
 			Start an early, polled-mode console on the 8250/16550
 			UART at the specified I/O port or MMIO address.
@@ -1184,7 +1184,9 @@
 			If none of [io|mmio|mmio32|mmio32be], <addr> is assumed
 			to be equivalent to 'mmio'. 'options' are specified
 			in the same format described for "console=ttyS<n>"; if
-			unspecified, the h/w is not initialized.
+			unspecified, the h/w is not initialized. 'uartclk' is
+			the uart clock frequency; if unspecified, it is set
+			to 'BASE_BAUD' * 16.
 
 		pl011,<addr>
 		pl011,mmio32,<addr>