Merge tag 'pinctrl-v3.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl into next

Pull pin control changes from Linus Walleij:
 "This is the bulk of pin control changes for the v3.16 development
  cycle:

   - Antoine Tenart made the get_group_pins() vtable entry optional.

   - Antoine also provides an entirely new driver for the Marvell Berlin
     SoC.  This is unrelated to the existing MVEBU hardware driver and
     warrants its own separate driver.

   - reflected from the GPIO subsystem there is a number of refactorings
     to make pin control drivers with gpiochips use the new gpiolib
     irqchip helpers.  The following drivers were converted to use the
     new infrastructure:
       * ST Microelectronics STiH416 and friends
       * The Atmel AT91
       * The CSR SiRF (Prima2)
       * The Qualcomm MSM series

   - massive improvements in the Qualcomm MSM driver from Bjorn
     Andersson, Andy Gross and Kumar Gala.  Among those new support for
     the IPQ8064 and MSM8x74 SoC variants.

   - support for the Freescale i.MX6 SoloX SoC variant.

   - massive improvements in the Allwinner sunxi driver from Boris
     Brezillon, Maxime Ripard and Chen-Yu Tsai.

   - Renesas PFC updates from Laurent Pinchart, Kuninori Morimoto,
     Wolfram Sang and Magnus Damm.

   - Cleanups and refactorings of the nVidia Tegra driver from Stepgen
     Warren.

   - the Exynos driver now supports the Exynos3250 SoC.

   - Intel BayTrail updates from Jin Yao, Mika Westerberg.

   - the MVEBU driver now supports the Orion5x SoC variants, which is
     part of the effort of getting rid of the old Marvell kludges in
     arch/arm/mach-orion5x

   - Rockchip driver updates from Heiko Stuebner.

   - a ton of cleanups and janitorial patches from Axel Lin.

   - some minor fixes and improvements here and there"

* tag 'pinctrl-v3.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (93 commits)
  pinctrl: sirf: fix a bad conflict resolution
  pinctrl: msm: Add more MSM8X74 pin definitions
  pinctrl: qcom: ipq8064: Fix naming convention
  pinctrl: msm: Add missing sdc1 and sdc3 groups
  pinctrl: sirf: switch to using allocated state container
  pinctrl: Enable "power-source" to be extracted from DT files
  pinctrl: sunxi: create irq/pin mapping during init
  pinctrl: pinconf-generic: Use kmemdup instead of kmalloc + memcpy
  pinctrl: berlin: Use devm_ioremap_resource()
  pinctrl: sirf: fix typo for GPIO bank number
  pinctrl: sunxi: depend on RESET_CONTROLLER
  pinctrl: sunxi: fix pin numbers passed to register offset helpers
  pinctrl: add pinctrl driver for imx6sx
  pinctrl/at91: Fix lockup when IRQ on PIOC and PIOD occurs
  pinctrl: msm: switch to using generic GPIO irqchip helpers
  pinctrl: sunxi: Fix multiple registration issue
  pinctrl: sunxi: Fix recursive dependency
  pinctrl: berlin: add the BG2CD pinctrl driver
  pinctrl: berlin: add the BG2 pinctrl driver
  pinctrl: berlin: add the BG2Q pinctrl driver
  ...

8 files changed, 360 insertions, 10 deletions

diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
index dff0e5f995e2..d8d065608ec0 100644
--- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
@@ -6,8 +6,13 @@ the first two functions being GPIO in and out. The configuration on
 the pins includes drive strength and pull-up.
 
 Required properties:
-- compatible: "allwinner,<soc>-pinctrl". Supported SoCs for now are:
-  sun5i-a13.
+- compatible: Should be one of the followings (depending on you SoC):
+  "allwinner,sun4i-a10-pinctrl"
+  "allwinner,sun5i-a10s-pinctrl"
+  "allwinner,sun5i-a13-pinctrl"
+  "allwinner,sun6i-a31-pinctrl"
+  "allwinner,sun6i-a31-r-pinctrl"
+  "allwinner,sun7i-a20-pinctrl"
 - reg: Should contain the register physical address and length for the
   pin controller.
 
diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx6sx-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx6sx-pinctrl.txt
new file mode 100644
index 000000000000..b1b595220f1b
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx6sx-pinctrl.txt
@@ -0,0 +1,36 @@
+* Freescale i.MX6 SoloX IOMUX Controller
+
+Please refer to fsl,imx-pinctrl.txt in this directory for common binding part
+and usage.
+
+Required properties:
+- compatible: "fsl,imx6sx-iomuxc"
+- fsl,pins: each entry consists of 6 integers and represents the mux and config
+  setting for one pin.  The first 5 integers <mux_reg conf_reg input_reg mux_val
+  input_val> are specified using a PIN_FUNC_ID macro, which can be found in
+  imx6sx-pinfunc.h under device tree source folder.  The last integer CONFIG is
+  the pad setting value like pull-up on this pin.  Please refer to i.MX6 SoloX
+  Reference Manual for detailed CONFIG settings.
+
+CONFIG bits definition:
+PAD_CTL_HYS                     (1 << 16)
+PAD_CTL_PUS_100K_DOWN           (0 << 14)
+PAD_CTL_PUS_47K_UP              (1 << 14)
+PAD_CTL_PUS_100K_UP             (2 << 14)
+PAD_CTL_PUS_22K_UP              (3 << 14)
+PAD_CTL_PUE                     (1 << 13)
+PAD_CTL_PKE                     (1 << 12)
+PAD_CTL_ODE                     (1 << 11)
+PAD_CTL_SPEED_LOW               (0 << 6)
+PAD_CTL_SPEED_MED               (1 << 6)
+PAD_CTL_SPEED_HIGH              (3 << 6)
+PAD_CTL_DSE_DISABLE             (0 << 3)
+PAD_CTL_DSE_260ohm              (1 << 3)
+PAD_CTL_DSE_130ohm              (2 << 3)
+PAD_CTL_DSE_87ohm               (3 << 3)
+PAD_CTL_DSE_65ohm               (4 << 3)
+PAD_CTL_DSE_52ohm               (5 << 3)
+PAD_CTL_DSE_43ohm               (6 << 3)
+PAD_CTL_DSE_37ohm               (7 << 3)
+PAD_CTL_SRE_FAST                (1 << 0)
+PAD_CTL_SRE_SLOW                (0 << 0)
diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,orion-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,orion-pinctrl.txt
new file mode 100644
index 000000000000..27570a3a1741
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/marvell,orion-pinctrl.txt
@@ -0,0 +1,91 @@
+* Marvell Orion SoC pinctrl driver for mpp
+
+Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding
+part and usage.
+
+Required properties:
+- compatible: "marvell,88f5181l-pinctrl", "marvell,88f5182-pinctrl",
+              "marvell,88f5281-pinctrl"
+
+- reg: two register areas, the first one describing the first two
+  contiguous MPP registers, and the second one describing the single
+  final MPP register, separated from the previous one.
+
+Available mpp pins/groups and functions:
+Note: brackets (x) are not part of the mpp name for marvell,function and given
+only for more detailed description in this document.
+
+* Marvell Orion 88f5181l
+
+name          pins     functions
+================================================================================
+mpp0          0        pcie(rstout), pci(req2), gpio
+mpp1          1        gpio, pci(gnt2)
+mpp2          2        gpio, pci(req3), pci-1(pme)
+mpp3          3        gpio, pci(gnt3)
+mpp4          4        gpio, pci(req4)
+mpp5          5        gpio, pci(gnt4)
+mpp6          6        gpio, pci(req5), pci-1(clk)
+mpp7          7        gpio, pci(gnt5), pci-1(clk)
+mpp8          8        gpio, ge(col)
+mpp9          9        gpio, ge(rxerr)
+mpp10         10       gpio, ge(crs)
+mpp11         11       gpio, ge(txerr)
+mpp12         12       gpio, ge(txd4)
+mpp13         13       gpio, ge(txd5)
+mpp14         14       gpio, ge(txd6)
+mpp15         15       gpio, ge(txd7)
+mpp16         16       ge(rxd4)
+mpp17         17       ge(rxd5)
+mpp18         18       ge(rxd6)
+mpp19         19       ge(rxd7)
+
+* Marvell Orion 88f5182
+
+name          pins     functions
+================================================================================
+mpp0          0        pcie(rstout), pci(req2), gpio
+mpp1          1        gpio, pci(gnt2)
+mpp2          2        gpio, pci(req3), pci-1(pme)
+mpp3          3        gpio, pci(gnt3)
+mpp4          4        gpio, pci(req4), bootnand(re), sata0(prsnt)
+mpp5          5        gpio, pci(gnt4), bootnand(we), sata1(prsnt)
+mpp6          6        gpio, pci(req5), nand(re0), sata0(act)
+mpp7          7        gpio, pci(gnt5), nand(we0), sata1(act)
+mpp8          8        gpio, ge(col)
+mpp9          9        gpio, ge(rxerr)
+mpp10         10       gpio, ge(crs)
+mpp11         11       gpio, ge(txerr)
+mpp12         12       gpio, ge(txd4), nand(re1), sata0(ledprsnt)
+mpp13         13       gpio, ge(txd5), nand(we1), sata1(ledprsnt)
+mpp14         14       gpio, ge(txd6), nand(re2), sata0(ledact)
+mpp15         15       gpio, ge(txd7), nand(we2), sata1(ledact)
+mpp16         16       uart1(rxd), ge(rxd4), gpio
+mpp17         17       uart1(txd), ge(rxd5), gpio
+mpp18         18       uart1(cts), ge(rxd6), gpio
+mpp19         19       uart1(rts), ge(rxd7), gpio
+
+* Marvell Orion 88f5281
+
+name          pins     functions
+================================================================================
+mpp0          0        pcie(rstout), pci(req2), gpio
+mpp1          1        gpio, pci(gnt2)
+mpp2          2        gpio, pci(req3), pci(pme)
+mpp3          3        gpio, pci(gnt3)
+mpp4          4        gpio, pci(req4), bootnand(re)
+mpp5          5        gpio, pci(gnt4), bootnand(we)
+mpp6          6        gpio, pci(req5), nand(re0)
+mpp7          7        gpio, pci(gnt5), nand(we0)
+mpp8          8        gpio, ge(col)
+mpp9          9        gpio, ge(rxerr)
+mpp10         10       gpio, ge(crs)
+mpp11         11       gpio, ge(txerr)
+mpp12         12       gpio, ge(txd4), nand(re1)
+mpp13         13       gpio, ge(txd5), nand(we1)
+mpp14         14       gpio, ge(txd6), nand(re2)
+mpp15         15       gpio, ge(txd7), nand(we2)
+mpp16         16       uart1(rxd), ge(rxd4)
+mpp17         17       uart1(txd), ge(rxd5)
+mpp18         18       uart1(cts), ge(rxd6)
+mpp19         19       uart1(rts), ge(rxd7)
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
index 4414163e76d2..fa40a177164c 100644
--- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
@@ -156,6 +156,7 @@ input-disable		- disable input on pin (no effect on output)
 input-schmitt-enable	- enable schmitt-trigger mode
 input-schmitt-disable	- disable schmitt-trigger mode
 input-debounce		- debounce mode with debound time X
+power-source		- select between different power supplies
 low-power-enable	- enable low power mode
 low-power-disable	- disable low power mode
 output-low		- set the pin to output mode with low level
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt
new file mode 100644
index 000000000000..7181f925acaa
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt
@@ -0,0 +1,88 @@
+Qualcomm APQ8064 TLMM block
+
+Required properties:
+- compatible: "qcom,apq8064-pinctrl"
+- reg: Should be the base address and length of the TLMM block.
+- interrupts: Should be the parent IRQ of the TLMM block.
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells: Should be two.
+- gpio-controller: Marks the device node as a GPIO controller.
+- #gpio-cells : Should be two.
+                The first cell is the gpio pin number and the
+                second cell is used for optional parameters.
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Qualcomm's pin configuration nodes act as a container for an abitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+ pins, function, bias-disable, bias-pull-down, bias-pull,up, drive-strength,
+ output-low, output-high.
+
+Non-empty subnodes must specify the 'pins' property.
+
+Valid values for pins are:
+  gpio0-gpio89
+
+Valid values for function are:
+  cam_mclk, codec_mic_i2s, codec_spkr_i2s, gsbi1, gsbi2, gsbi3, gsbi4,
+  gsbi4_cam_i2c, gsbi5, gsbi5_spi_cs1, gsbi5_spi_cs2, gsbi5_spi_cs3, gsbi6,
+  gsbi6_spi_cs1, gsbi6_spi_cs2, gsbi6_spi_cs3, gsbi7, gsbi7_spi_cs1,
+  gsbi7_spi_cs2, gsbi7_spi_cs3, gsbi_cam_i2c, hdmi, mi2s, riva_bt, riva_fm,
+  riva_wlan, sdc2, sdc4, slimbus, spkr_i2s, tsif1, tsif2, usb2_hsic,
+
+Example:
+
+	msmgpio: pinctrl@800000 {
+		compatible = "qcom,apq8064-pinctrl";
+		reg = <0x800000 0x4000>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupts = <0 32 0x4>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gsbi5_uart_default>;
+
+		gsbi5_uart_default: gsbi5_uart_default {
+			mux {
+				pins = "gpio51", "gpio52";
+				function = "gsbi5";
+			};
+
+			tx {
+				pins = "gpio51";
+				drive-strength = <4>;
+				bias-disable;
+			};
+
+			rx {
+				pins = "gpio52";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt
new file mode 100644
index 000000000000..e0d35a40981b
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt
@@ -0,0 +1,95 @@
+Qualcomm IPQ8064 TLMM block
+
+Required properties:
+- compatible: "qcom,ipq8064-pinctrl"
+- reg: Should be the base address and length of the TLMM block.
+- interrupts: Should be the parent IRQ of the TLMM block.
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells: Should be two.
+- gpio-controller: Marks the device node as a GPIO controller.
+- #gpio-cells : Should be two.
+                The first cell is the gpio pin number and the
+                second cell is used for optional parameters.
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Qualcomm's pin configuration nodes act as a container for an abitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+ pins, function, bias-disable, bias-pull-down, bias-pull,up, drive-strength,
+ output-low, output-high.
+
+Non-empty subnodes must specify the 'pins' property.
+
+Valid values for qcom,pins are:
+  gpio0-gpio68
+   Supports mux, bias, and drive-strength
+
+  sdc3_clk, sdc3_cmd, sdc3_data
+   Supports bias and drive-strength
+
+
+Valid values for function are:
+  mdio, mi2s, pdm, ssbi, spmi, audio_pcm, gsbi1, gsbi2, gsbi4, gsbi5,
+  gsbi5_spi_cs1, gsbi5_spi_cs2, gsbi5_spi_cs3, gsbi6, gsbi7, nss_spi, sdc1,
+  spdif, nand, tsif1, tsif2, usb_fs_n, usb_fs, usb2_hsic, rgmii2, sata,
+  pcie1_rst, pcie1_prsnt, pcie1_pwren_n, pcie1_pwren, pcie1_pwrflt,
+  pcie1_clk_req, pcie2_rst, pcie2_prsnt, pcie2_pwren_n, pcie2_pwren,
+  pcie2_pwrflt, pcie2_clk_req, pcie3_rst, pcie3_prsnt, pcie3_pwren_n,
+  pcie3_pwren, pcie3_pwrflt, pcie3_clk_req, ps_hold
+
+Example:
+
+	pinmux: pinctrl@800000 {
+		compatible = "qcom,ipq8064-pinctrl";
+		reg = <0x800000 0x4000>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupts = <0 32 0x4>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gsbi5_uart_default>;
+
+		gsbi5_uart_default: gsbi5_uart_default {
+			mux {
+				pins = "gpio18", "gpio19";
+				function = "gsbi5";
+			};
+
+			tx {
+				pins = "gpio18";
+				drive-strength = <4>;
+				bias-disable;
+			};
+
+			rx {
+				pins = "gpio19";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt
index 9fb89e3f61ea..73262b575dfc 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt
@@ -50,7 +50,27 @@ Valid values for pins are:
     Supports bias and drive-strength
 
 Valid values for function are:
-  blsp_i2c2, blsp_i2c6, blsp_i2c11, blsp_spi1, blsp_uart2, blsp_uart8, slimbus
+  cci_i2c0, cci_i2c1, uim1, uim2, uim_batt_alarm,
+  blsp_uim1, blsp_uart1, blsp_i2c1, blsp_spi1,
+  blsp_uim2, blsp_uart2, blsp_i2c2, blsp_spi2,
+  blsp_uim3, blsp_uart3, blsp_i2c3, blsp_spi3,
+  blsp_uim4, blsp_uart4, blsp_i2c4, blsp_spi4,
+  blsp_uim5, blsp_uart5, blsp_i2c5, blsp_spi5,
+  blsp_uim6, blsp_uart6, blsp_i2c6, blsp_spi6,
+  blsp_uim7, blsp_uart7, blsp_i2c7, blsp_spi7,
+  blsp_uim8, blsp_uart8, blsp_i2c8, blsp_spi8,
+  blsp_uim9, blsp_uart9, blsp_i2c9, blsp_spi9,
+  blsp_uim10, blsp_uart10, blsp_i2c10, blsp_spi10,
+  blsp_uim11, blsp_uart11, blsp_i2c11, blsp_spi11,
+  blsp_uim12, blsp_uart12, blsp_i2c12, blsp_spi12,
+  blsp_spi1_cs1, blsp_spi2_cs2, blsp_spi_cs3, blsp_spi2_cs1, blsp_spi2_cs2
+  blsp_spi2_cs3, blsp_spi10_cs1, blsp_spi10_cs2, blsp_spi10_cs3,
+  sdc3, sdc4, gcc_gp_clk1, gcc_gp_clk2, gcc_gp_clk3, cci_timer0, cci_timer1,
+  cci_timer2, cci_timer3, cci_async_in0, cci_async_in1, cci_async_in2,
+  cam_mckl0, cam_mclk1, cam_mclk2, cam_mclk3, mdp_vsync, hdmi_cec, hdmi_ddc,
+  hdmi_hpd, edp_hpd, gp_pdm0, gp_pdm1, gp_pdm2, gp_pdm3, gp0_clk, gp1_clk,
+  gp_mn, tsif1, tsif2, hsic, grfc, audio_ref_clk, qua_mi2s, pri_mi2s, spkr_mi2s,
+  ter_mi2s, sec_mi2s, bt, fm, wlan, slimbus
 
   (Note that this is not yet the complete list of functions)
 
diff --git a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt
index f378d342aae4..cefef741a40b 100644
--- a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt
@@ -21,13 +21,23 @@ defined as gpio sub-nodes of the pinmux controller.
 Required properties for iomux controller:
   - compatible: one of "rockchip,rk2928-pinctrl", "rockchip,rk3066a-pinctrl"
 		       "rockchip,rk3066b-pinctrl", "rockchip,rk3188-pinctrl"
+  - rockchip,grf: phandle referencing a syscon providing the
+	 "general register files"
+
+Optional properties for iomux controller:
+  - rockchip,pmu: phandle referencing a syscon providing the pmu registers
+	 as some SoCs carry parts of the iomux controller registers there.
+	 Required for at least rk3188 and rk3288.
+
+Deprecated properties for iomux controller:
   - reg: first element is the general register space of the iomux controller
-	 second element is the separate pull register space of the rk3188
+	 It should be large enough to contain also separate pull registers.
+	 second element is the separate pull register space of the rk3188.
+	 Use rockchip,grf and rockchip,pmu described above instead.
 
 Required properties for gpio sub nodes:
   - compatible: "rockchip,gpio-bank", "rockchip,rk3188-gpio-bank0"
   - reg: register of the gpio bank (different than the iomux registerset)
-         second element: separate pull register for rk3188 bank0
   - interrupts: base interrupt of the gpio bank in the interrupt controller
   - clocks: clock that drives this bank
   - gpio-controller: identifies the node as a gpio controller and pin bank.
@@ -39,6 +49,10 @@ Required properties for gpio sub nodes:
     cells should use the standard two-cell scheme described in
     bindings/interrupt-controller/interrupts.txt
 
+Deprecated properties for gpio sub nodes:
+  - reg: second element: separate pull register for rk3188 bank0, use
+	 rockchip,pmu described above instead
+
 Required properties for pin configuration node:
   - rockchip,pins: 3 integers array, represents a group of pins mux and config
     setting. The format is rockchip,pins = <PIN_BANK PIN_BANK_IDX MUX &phandle>.
@@ -54,7 +68,8 @@ Examples:
 
 pinctrl@20008000 {
 	compatible = "rockchip,rk3066a-pinctrl";
-	reg = <0x20008000 0x150>;
+	rockchip,grf = <&grf>;
+
 	#address-cells = <1>;
 	#size-cells = <1>;
 	ranges;
@@ -103,16 +118,15 @@ Example for rk3188:
 
 	pinctrl@20008000 {
 		compatible = "rockchip,rk3188-pinctrl";
-		reg = <0x20008000 0xa0>,
-		      <0x20008164 0x1a0>;
+		rockchip,grf = <&grf>;
+		rockchip,pmu = <&pmu>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges;
 
 		gpio0: gpio0@0x2000a000 {
 			compatible = "rockchip,rk3188-gpio-bank0";
-			reg = <0x2000a000 0x100>,
-			      <0x20004064 0x8>;
+			reg = <0x2000a000 0x100>;
 			interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clk_gates8 9>;