Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

Pull networking updates from David Miller:
 "Another merge window, another set of networking changes.  I've heard
  rumblings that the lightweight tunnels infrastructure has been voted
  networking change of the year.  But what do I know?

   1) Add conntrack support to openvswitch, from Joe Stringer.

   2) Initial support for VRF (Virtual Routing and Forwarding), which
      allows the segmentation of routing paths without using multiple
      devices.  There are some semantic kinks to work out still, but
      this is a reasonably strong foundation.  From David Ahern.

   3) Remove spinlock fro act_bpf fast path, from Alexei Starovoitov.

   4) Ignore route nexthops with a link down state in ipv6, just like
      ipv4.  From Andy Gospodarek.

   5) Remove spinlock from fast path of act_gact and act_mirred, from
      Eric Dumazet.

   6) Document the DSA layer, from Florian Fainelli.

   7) Add netconsole support to bcmgenet, systemport, and DSA.  Also
      from Florian Fainelli.

   8) Add Mellanox Switch Driver and core infrastructure, from Jiri
      Pirko.

   9) Add support for "light weight tunnels", which allow for
      encapsulation and decapsulation without bearing the overhead of a
      full blown netdevice.  From Thomas Graf, Jiri Benc, and a cast of
      others.

  10) Add Identifier Locator Addressing support for ipv6, from Tom
      Herbert.

  11) Support fragmented SKBs in iwlwifi, from Johannes Berg.

  12) Allow perf PMUs to be accessed from eBPF programs, from Kaixu Xia.

  13) Add BQL support to 3c59x driver, from Loganaden Velvindron.

  14) Stop using a zero TX queue length to mean that a device shouldn't
      have a qdisc attached, use an explicit flag instead.  From Phil
      Sutter.

  15) Use generic geneve netdevice infrastructure in openvswitch, from
      Pravin B Shelar.

  16) Add infrastructure to avoid re-forwarding a packet in software
      that was already forwarded by a hardware switch.  From Scott
      Feldman.

  17) Allow AF_PACKET fanout function to be implemented in a bpf
      program, from Willem de Bruijn"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1458 commits)
  netfilter: nf_conntrack: make nf_ct_zone_dflt built-in
  netfilter: nf_dup{4, 6}: fix build error when nf_conntrack disabled
  net: fec: clear receive interrupts before processing a packet
  ipv6: fix exthdrs offload registration in out_rt path
  xen-netback: add support for multicast control
  bgmac: Update fixed_phy_register()
  sock, diag: fix panic in sock_diag_put_filterinfo
  flow_dissector: Use 'const' where possible.
  flow_dissector: Fix function argument ordering dependency
  ixgbe: Resolve "initialized field overwritten" warnings
  ixgbe: Remove bimodal SR-IOV disabling
  ixgbe: Add support for reporting 2.5G link speed
  ixgbe: fix bounds checking in ixgbe_setup_tc for 82598
  ixgbe: support for ethtool set_rxfh
  ixgbe: Avoid needless PHY access on copper phys
  ixgbe: cleanup to use cached mask value
  ixgbe: Remove second instance of lan_id variable
  ixgbe: use kzalloc for allocating one thing
  flow: Move __get_hash_from_flowi{4,6} into flow_dissector.c
  ixgbe: Remove unused PCI bus types
  ...

8 files changed, 187 insertions, 8 deletions

diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.txt b/Documentation/devicetree/bindings/net/dsa/dsa.txt
index f0b4cd72411d..04e6bef3ac3f 100644
--- a/Documentation/devicetree/bindings/net/dsa/dsa.txt
+++ b/Documentation/devicetree/bindings/net/dsa/dsa.txt
@@ -44,9 +44,10 @@ Note that a port labelled "dsa" will imply checking for the uplink phandle
 described below.
 
 Optionnal property:
-- link			: Should be a phandle to another switch's DSA port.
+- link			: Should be a list of phandles to another switch's DSA port.
 			  This property is only used when switches are being
-			  chained/cascaded together.
+			  chained/cascaded together. This port is used as outgoing port
+			  towards the phandle port, which can be more than one hop away.
 
 - phy-handle		: Phandle to a PHY on an external MDIO bus, not the
 			  switch internal one. See
@@ -58,6 +59,10 @@ Optionnal property:
 			  Documentation/devicetree/bindings/net/ethernet.txt
 			  for details.
 
+- mii-bus		: Should be a phandle to a valid MDIO bus device node.
+			  This mii-bus will be used in preference to the
+			  global dsa,mii-bus defined above, for this switch.
+
 Optional subnodes:
 - fixed-link		: Fixed-link subnode describing a link to a non-MDIO
 			  managed entity. See
@@ -96,10 +101,11 @@ Example:
 				label = "cpu";
 			};
 
-			switch0uplink: port@6 {
+			switch0port6: port@6 {
 				reg = <6>;
 				label = "dsa";
-				link = <&switch1uplink>;
+				link = <&switch1port0
+				        &switch2port0>;
 			};
 		};
 
@@ -107,11 +113,31 @@ Example:
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <17 1>;	/* MDIO address 17, switch 1 in tree */
+			mii-bus = <&mii_bus1>;
+
+			switch1port0: port@0 {
+				reg = <0>;
+				label = "dsa";
+				link = <&switch0port6>;
+			};
+			switch1port1: port@1 {
+				reg = <1>;
+				label = "dsa";
+				link = <&switch2port1>;
+			};
+		};
+
+		switch@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <18 2>;	/* MDIO address 18, switch 2 in tree */
+			mii-bus = <&mii_bus1>;
 
-			switch1uplink: port@0 {
+			switch2port0: port@0 {
 				reg = <0>;
 				label = "dsa";
-				link = <&switch0uplink>;
+				link = <&switch1port1
+				        &switch0port6>;
 			};
 		};
 	};
diff --git a/Documentation/devicetree/bindings/net/ethernet.txt b/Documentation/devicetree/bindings/net/ethernet.txt
index 41b3f3f864e8..5d88f37480b6 100644
--- a/Documentation/devicetree/bindings/net/ethernet.txt
+++ b/Documentation/devicetree/bindings/net/ethernet.txt
@@ -25,7 +25,11 @@ The following properties are common to the Ethernet controllers:
   flow control thresholds.
 - tx-fifo-depth: the size of the controller's transmit fifo in bytes. This
   is used for components that can have configurable fifo sizes.
+- managed: string, specifies the PHY management type. Supported values are:
+  "auto", "in-band-status". "auto" is the default, it usess MDIO for
+  management if fixed-link is not specified.
 
 Child nodes of the Ethernet controller are typically the individual PHY devices
 connected via the MDIO bus (sometimes the MDIO bus controller is separate).
 They are described in the phy.txt file in this same directory.
+For non-MDIO PHY management see fixed-link.txt.
diff --git a/Documentation/devicetree/bindings/net/fixed-link.txt b/Documentation/devicetree/bindings/net/fixed-link.txt
index 82bf7e0f47b6..ec5d889fe3d8 100644
--- a/Documentation/devicetree/bindings/net/fixed-link.txt
+++ b/Documentation/devicetree/bindings/net/fixed-link.txt
@@ -17,6 +17,8 @@ properties:
   enabled.
 * 'asym-pause' (boolean, optional), to indicate that asym_pause should
   be enabled.
+* 'link-gpios' ('gpio-list', optional), to indicate if a gpio can be read
+  to determine if the link is up.
 
 Old, deprecated 'fixed-link' binding:
 
@@ -30,7 +32,7 @@ Old, deprecated 'fixed-link' binding:
   - e: asymmetric pause configuration: 0 for no asymmetric pause, 1 for
     asymmetric pause
 
-Example:
+Examples:
 
 ethernet@0 {
 	...
@@ -40,3 +42,13 @@ ethernet@0 {
 	};
 	...
 };
+
+ethernet@1 {
+	...
+	fixed-link {
+	      speed = <1000>;
+	      pause;
+	      link-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+	};
+	...
+};
diff --git a/Documentation/devicetree/bindings/net/keystone-netcp.txt b/Documentation/devicetree/bindings/net/keystone-netcp.txt
index d0e6fa38f335..b30ab6b5cbfa 100644
--- a/Documentation/devicetree/bindings/net/keystone-netcp.txt
+++ b/Documentation/devicetree/bindings/net/keystone-netcp.txt
@@ -130,7 +130,11 @@ Required properties:
 
 Optional properties:
 - efuse-mac:	If this is 1, then the MAC address for the interface is
-		obtained from the device efuse mac address register
+		obtained from the device efuse mac address register.
+		If this is 2, the two DWORDs occupied by the MAC address
+		are swapped.  The netcp driver will swap the two DWORDs
+		back to the proper order when this property is set to 2
+		when it obtains the mac address from efuse.
 - local-mac-address:	the driver is designed to use the of_get_mac_address api
 			only if efuse-mac is 0. When efuse-mac is 0, the MAC
 			address is obtained from local-mac-address. If this
diff --git a/Documentation/devicetree/bindings/net/nfc/s3fwrn5.txt b/Documentation/devicetree/bindings/net/nfc/s3fwrn5.txt
new file mode 100644
index 000000000000..fb1e75facf1b
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/nfc/s3fwrn5.txt
@@ -0,0 +1,27 @@
+* Samsung S3FWRN5 NCI NFC Controller
+
+Required properties:
+- compatible: Should be "samsung,s3fwrn5-i2c".
+- reg: address on the bus
+- interrupt-parent: phandle for the interrupt gpio controller
+- interrupts: GPIO interrupt to which the chip is connected
+- s3fwrn5,en-gpios: Output GPIO pin used for enabling/disabling the chip
+- s3fwrn5,fw-gpios: Output GPIO pin used to enter firmware mode and
+  sleep/wakeup control
+
+Example:
+
+&hsi2c_4 {
+	status = "okay";
+	s3fwrn5@27 {
+		compatible = "samsung,s3fwrn5-i2c";
+
+		reg = <0x27>;
+
+		interrupt-parent = <&gpa1>;
+		interrupts = <3 0 0>;
+
+		s3fwrn5,en-gpios = <&gpf1 4 0>;
+		s3fwrn5,fw-gpios = <&gpj0 2 0>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/nfc/st-nci.txt b/Documentation/devicetree/bindings/net/nfc/st-nci-i2c.txt
index d707588ed734..d707588ed734 100644
--- a/Documentation/devicetree/bindings/net/nfc/st-nci.txt
+++ b/Documentation/devicetree/bindings/net/nfc/st-nci-i2c.txt
diff --git a/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt b/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt
new file mode 100644
index 000000000000..525681b6dc39
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt
@@ -0,0 +1,31 @@
+* STMicroelectronics SAS. ST NCI NFC Controller
+
+Required properties:
+- compatible: Should be "st,st21nfcb-spi"
+- spi-max-frequency: Maximum SPI frequency (<= 10000000).
+- interrupt-parent: phandle for the interrupt gpio controller
+- interrupts: GPIO interrupt to which the chip is connected
+- reset-gpios: Output GPIO pin used to reset the ST21NFCB
+
+Optional SoC Specific Properties:
+- pinctrl-names: Contains only one value - "default".
+- pintctrl-0: Specifies the pin control groups used for this controller.
+
+Example (for ARM-based BeagleBoard xM with ST21NFCB on SPI4):
+
+&mcspi4 {
+
+	status = "okay";
+
+	st21nfcb: st21nfcb@0 {
+
+		compatible = "st,st21nfcb-spi";
+
+		clock-frequency = <4000000>;
+
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_EDGE_RISING>;
+
+		reset-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt b/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt
new file mode 100644
index 000000000000..51f8d2eba8d8
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt
@@ -0,0 +1,75 @@
+* Synopsys DWC Ethernet QoS IP version 4.10 driver (GMAC)
+
+
+Required properties:
+- compatible: Should be "snps,dwc-qos-ethernet-4.10"
+- reg: Address and length of the register set for the device
+- clocks: Phandles to the reference clock and the bus clock
+- clock-names: Should be "phy_ref_clk" for the reference clock and "apb_pclk"
+  for the bus clock.
+- interrupt-parent: Should be the phandle for the interrupt controller
+  that services interrupts for this device
+- interrupts: Should contain the core's combined interrupt signal
+- phy-mode: See ethernet.txt file in the same directory
+
+Optional properties:
+- dma-coherent: Present if dma operations are coherent
+- mac-address: See ethernet.txt in the same directory
+- local-mac-address: See ethernet.txt in the same directory
+- snps,en-lpi: If present it enables use of the AXI low-power interface
+- snps,write-requests: Number of write requests that the AXI port can issue.
+  It depends on the SoC configuration.
+- snps,read-requests: Number of read requests that the AXI port can issue.
+  It depends on the SoC configuration.
+- snps,burst-map: Bitmap of allowed AXI burst lengts, with the LSB
+  representing 4, then 8 etc.
+- snps,txpbl: DMA Programmable burst length for the TX DMA
+- snps,rxpbl: DMA Programmable burst length for the RX DMA
+- snps,en-tx-lpi-clockgating: Enable gating of the MAC TX clock during
+  TX low-power mode.
+- phy-handle: See ethernet.txt file in the same directory
+- mdio device tree subnode: When the GMAC has a phy connected to its local
+    mdio, there must be device tree subnode with the following
+    required properties:
+    - compatible: Must be "snps,dwc-qos-ethernet-mdio".
+    - #address-cells: Must be <1>.
+    - #size-cells: Must be <0>.
+
+    For each phy on the mdio bus, there must be a node with the following
+    fields:
+
+    - reg: phy id used to communicate to phy.
+    - device_type: Must be "ethernet-phy".
+    - fixed-mode device tree subnode: see fixed-link.txt in the same directory
+
+Examples:
+ethernet2@40010000 {
+	clock-names = "phy_ref_clk", "apb_pclk";
+	clocks = <&clkc 17>, <&clkc 15>;
+	compatible = "snps,dwc-qos-ethernet-4.10";
+	interrupt-parent = <&intc>;
+	interrupts = <0x0 0x1e 0x4>;
+	reg = <0x40010000 0x4000>;
+	phy-handle = <&phy2>;
+	phy-mode = "gmii";
+
+	snps,en-tx-lpi-clockgating;
+	snps,en-lpi;
+	snps,write-requests = <2>;
+	snps,read-requests = <16>;
+	snps,burst-map = <0x7>;
+	snps,txpbl = <8>;
+	snps,rxpbl = <2>;
+
+	dma-coherent;
+
+	mdio {
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+		phy2: phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			device_type = "ethernet-phy";
+			reg = <0x1>;
+		};
+	};
+};