pinctrl: Add pinctrl binding for Broadcom Capri SoCs

Adds pinctrl driver devicetree binding for Broadcom Capri (BCM281xx) SoCs.

v4: Changed valid values for "bias-pull-up" property for I2C pins.
    Expanded pin configuration node example.
v3: Use generic pin config properties instead of brcm-specific ones.
    Clarified pin types (standard, i2c, hdmi).
v2: Use hyphens instead of underscore in DT property names.

Device tree bindings maintainers ECG:
           _             _          _        _        _
__________/ \   ________/ \   _____/ \   ___/ \   ___/ \   __
             \_/           \_/        \_/      \_/      \_/

Signed-off-by: Sherman Yin <syin@broadcom.com>
Reviewed-by: Christian Daudt <bcm@fixthebug.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

1 files changed, 461 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,capri-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/brcm,capri-pinctrl.txt
new file mode 100644
index 000000000000..9e9e9ef9f852
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/brcm,capri-pinctrl.txt
@@ -0,0 +1,461 @@
+Broadcom Capri Pin Controller
+
+This is a pin controller for the Broadcom BCM281xx SoC family, which includes
+BCM11130, BCM11140, BCM11351, BCM28145, and BCM28155 SoCs.
+
+=== Pin Controller Node ===
+
+Required Properties:
+
+- compatible:	Must be "brcm,capri-pinctrl".
+- reg:		Base address of the PAD Controller register block and the size
+		of the block.
+
+For example, the following is the bare minimum node:
+
+	pinctrl@35004800 {
+		compatible = "brcm,capri-pinctrl";
+		reg = <0x35004800 0x430>;
+	};
+
+As a pin controller device, in addition to the required properties, this node
+should also contain the pin configuration nodes that client devices reference,
+if any.
+
+=== Pin Configuration Node ===
+
+Each pin configuration node is a sub-node of the pin controller node and is a
+container of an arbitrary number of subnodes, called pin group nodes in this
+document.
+
+Please refer to the pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the definition of a
+"pin configuration node".
+
+=== Pin Group Node ===
+
+A pin group node specifies the desired pin mux and/or pin configuration for an
+arbitrary number of pins.  The name of the pin group node is optional and not
+used.
+
+A pin group node only affects the properties specified in the node, and has no
+effect on any properties that are omitted.
+
+The pin group node accepts a subset of the generic pin config properties. For
+details generic pin config properties, please refer to pinctrl-bindings.txt
+and <include/linux/pinctrl/pinconfig-generic.h>.
+
+Each pin controlled by this pin controller belong to one of three types:
+Standard, I2C, and HDMI.  Each type accepts a different set of pin config
+properties.  A list of pins and their types is provided below.
+
+Required Properties (applicable to all pins):
+
+- pins:		Multiple strings.  Specifies the name(s) of one or more pins to
+		be configured by this node.
+
+Optional Properties (for standard pins):
+
+- function:			String. Specifies the pin mux selection. Values
+				must be one of: "alt1", "alt2", "alt3", "alt4"
+- input-schmitt-enable:		No arguments. Enable schmitt-trigger mode.
+- input-schmitt-disable:	No arguments. Disable schmitt-trigger mode.
+- bias-pull-up:			No arguments. Pull up on pin.
+- bias-pull-down:		No arguments. Pull down on pin.
+- bias-disable:			No arguments. Disable pin bias.
+- slew-rate:			Integer. Meaning depends on configured pin mux:
+				*_SCL or *_SDA:
+					0: Standard(100kbps)& Fast(400kbps) mode
+					1: Highspeed (3.4Mbps) mode
+				IC_DM or IC_DP:
+					0: normal slew rate
+					1: fast slew rate
+				Otherwise:
+					0: fast slew rate
+					1: normal slew rate
+- input-enable:			No arguements. Enable input (does not affect
+				output.)
+- input-disable:		No arguements. Disable input (does not affect
+				output.)
+- drive-strength:		Integer. Drive strength in mA.  Valid values are
+				2, 4, 6, 8, 10, 12, 14, 16 mA.
+
+Optional Properties (for I2C pins):
+
+- function:			String. Specifies the pin mux selection. Values
+				must be one of: "alt1", "alt2", "alt3", "alt4"
+- bias-pull-up:			Integer. Pull up strength in Ohm. There are 3
+				pull-up resisitors (1.2k, 1.8k, 2.7k) available
+				in parallel for I2C pins, so the valid values
+				are: 568, 720, 831, 1080, 1200, 1800, 2700 Ohm.
+- bias-disable:			No arguments. Disable pin bias.
+- slew-rate:			Integer. Meaning depends on configured pin mux:
+				*_SCL or *_SDA:
+					0: Standard(100kbps)& Fast(400kbps) mode
+					1: Highspeed (3.4Mbps) mode
+				IC_DM or IC_DP:
+					0: normal slew rate
+					1: fast slew rate
+				Otherwise:
+					0: fast slew rate
+					1: normal slew rate
+- input-enable:			No arguements. Enable input (does not affect
+				output.)
+- input-disable:		No arguements. Disable input (does not affect
+				output.)
+
+Optional Properties (for HDMI pins):
+
+- function:			String. Specifies the pin mux selection. Values
+				must be one of: "alt1", "alt2", "alt3", "alt4"
+- slew-rate:			Integer. Controls slew rate.
+					0: Standard(100kbps)& Fast(400kbps) mode
+					1: Highspeed (3.4Mbps) mode
+- input-enable:			No arguements. Enable input (does not affect
+				output.)
+- input-disable:		No arguements. Disable input (does not affect
+				output.)
+
+Example:
+// pin controller node
+pinctrl@35004800 {
+	compatible = "brcm,capri-pinctrl";
+	reg = <0x35004800 0x430>;
+
+	// pin configuration node
+	dev_a_default: dev_a_active {
+		//group node defining 1 standard pin
+		grp_1 {
+			pins		= "std_pin1";
+			function	= "alt1";
+			input-schmitt-enable;
+			bias-disable;
+			slew-rate	= <1>;
+			drive-strength	= <4>;
+		};
+
+		// group node defining 2 I2C pins
+		grp_2 {
+			pins		= "i2c_pin1", "i2c_pin2";
+			function	= "alt2";
+			bias-pull-up	= <720>;
+			input-enable;
+		};
+
+		// group node defining 2 HDMI pins
+		grp_3 {
+			pins		= "hdmi_pin1", "hdmi_pin2";
+			function	= "alt3";
+			slew-rate	= <1>;
+		};
+
+		// other pin group nodes
+		...
+	};
+
+	// other pin configuration nodes
+	...
+};
+
+In the example above, "dev_a_active" is a pin configuration node with a number
+of sub-nodes.  In the pin group node "grp_1", one pin, "std_pin1", is defined in
+the "pins" property.  Thus, the remaining properties in the "grp_1" node applies
+only to this pin, including the following settings:
+ - setting pinmux to "alt1"
+ - enabling schmitt-trigger (hystersis) mode
+ - disabling pin bias
+ - setting the slew-rate to 1
+ - setting the drive strength to 4 mA
+Note that neither "input-enable" nor "input-disable" was specified - the pinctrl
+subsystem will therefore leave this property unchanged from whatever state it
+was in before applying these changes.
+
+The "pins" property in the pin group node "grp_2" specifies two pins -
+"i2c_pin1" and "i2c_pin2"; the remaining properties in this pin group node,
+therefore, applies to both of these pins.  The properties include:
+ - setting pinmux to "alt2"
+ - setting pull-up resistance to 720 Ohm (ie. enabling 1.2k and 1.8k resistors
+   in parallel)
+ - enabling both pins' input
+"slew-rate" is not specified in this pin group node, so the slew-rate for these
+pins are left as-is.
+
+Finally, "grp_3" defines two HDMI pins.  The following properties are applied to
+both pins:
+ - setting pinmux to "alt3"
+ - setting slew-rate to 1; for HDMI pins, this corresponds to the 3.4 Mbps
+   Highspeed mode
+The input is neither enabled or disabled, and is left untouched.
+
+=== Pin Names and Type ===
+
+The following are valid pin names and their pin types:
+
+	"adcsync",		Standard
+	"bat_rm",		Standard
+	"bsc1_scl",		I2C
+	"bsc1_sda",		I2C
+	"bsc2_scl",		I2C
+	"bsc2_sda",		I2C
+	"classgpwr",		Standard
+	"clk_cx8",		Standard
+	"clkout_0",		Standard
+	"clkout_1",		Standard
+	"clkout_2",		Standard
+	"clkout_3",		Standard
+	"clkreq_in_0",		Standard
+	"clkreq_in_1",		Standard
+	"cws_sys_req1",		Standard
+	"cws_sys_req2",		Standard
+	"cws_sys_req3",		Standard
+	"digmic1_clk",		Standard
+	"digmic1_dq",		Standard
+	"digmic2_clk",		Standard
+	"digmic2_dq",		Standard
+	"gpen13",		Standard
+	"gpen14",		Standard
+	"gpen15",		Standard
+	"gpio00",		Standard
+	"gpio01",		Standard
+	"gpio02",		Standard
+	"gpio03",		Standard
+	"gpio04",		Standard
+	"gpio05",		Standard
+	"gpio06",		Standard
+	"gpio07",		Standard
+	"gpio08",		Standard
+	"gpio09",		Standard
+	"gpio10",		Standard
+	"gpio11",		Standard
+	"gpio12",		Standard
+	"gpio13",		Standard
+	"gpio14",		Standard
+	"gps_pablank",		Standard
+	"gps_tmark",		Standard
+	"hdmi_scl",		HDMI
+	"hdmi_sda",		HDMI
+	"ic_dm",		Standard
+	"ic_dp",		Standard
+	"kp_col_ip_0",		Standard
+	"kp_col_ip_1",		Standard
+	"kp_col_ip_2",		Standard
+	"kp_col_ip_3",		Standard
+	"kp_row_op_0",		Standard
+	"kp_row_op_1",		Standard
+	"kp_row_op_2",		Standard
+	"kp_row_op_3",		Standard
+	"lcd_b_0",		Standard
+	"lcd_b_1",		Standard
+	"lcd_b_2",		Standard
+	"lcd_b_3",		Standard
+	"lcd_b_4",		Standard
+	"lcd_b_5",		Standard
+	"lcd_b_6",		Standard
+	"lcd_b_7",		Standard
+	"lcd_g_0",		Standard
+	"lcd_g_1",		Standard
+	"lcd_g_2",		Standard
+	"lcd_g_3",		Standard
+	"lcd_g_4",		Standard
+	"lcd_g_5",		Standard
+	"lcd_g_6",		Standard
+	"lcd_g_7",		Standard
+	"lcd_hsync",		Standard
+	"lcd_oe",		Standard
+	"lcd_pclk",		Standard
+	"lcd_r_0",		Standard
+	"lcd_r_1",		Standard
+	"lcd_r_2",		Standard
+	"lcd_r_3",		Standard
+	"lcd_r_4",		Standard
+	"lcd_r_5",		Standard
+	"lcd_r_6",		Standard
+	"lcd_r_7",		Standard
+	"lcd_vsync",		Standard
+	"mdmgpio0",		Standard
+	"mdmgpio1",		Standard
+	"mdmgpio2",		Standard
+	"mdmgpio3",		Standard
+	"mdmgpio4",		Standard
+	"mdmgpio5",		Standard
+	"mdmgpio6",		Standard
+	"mdmgpio7",		Standard
+	"mdmgpio8",		Standard
+	"mphi_data_0",		Standard
+	"mphi_data_1",		Standard
+	"mphi_data_2",		Standard
+	"mphi_data_3",		Standard
+	"mphi_data_4",		Standard
+	"mphi_data_5",		Standard
+	"mphi_data_6",		Standard
+	"mphi_data_7",		Standard
+	"mphi_data_8",		Standard
+	"mphi_data_9",		Standard
+	"mphi_data_10",		Standard
+	"mphi_data_11",		Standard
+	"mphi_data_12",		Standard
+	"mphi_data_13",		Standard
+	"mphi_data_14",		Standard
+	"mphi_data_15",		Standard
+	"mphi_ha0",		Standard
+	"mphi_hat0",		Standard
+	"mphi_hat1",		Standard
+	"mphi_hce0_n",		Standard
+	"mphi_hce1_n",		Standard
+	"mphi_hrd_n",		Standard
+	"mphi_hwr_n",		Standard
+	"mphi_run0",		Standard
+	"mphi_run1",		Standard
+	"mtx_scan_clk",		Standard
+	"mtx_scan_data",	Standard
+	"nand_ad_0",		Standard
+	"nand_ad_1",		Standard
+	"nand_ad_2",		Standard
+	"nand_ad_3",		Standard
+	"nand_ad_4",		Standard
+	"nand_ad_5",		Standard
+	"nand_ad_6",		Standard
+	"nand_ad_7",		Standard
+	"nand_ale",		Standard
+	"nand_cen_0",		Standard
+	"nand_cen_1",		Standard
+	"nand_cle",		Standard
+	"nand_oen",		Standard
+	"nand_rdy_0",		Standard
+	"nand_rdy_1",		Standard
+	"nand_wen",		Standard
+	"nand_wp",		Standard
+	"pc1",			Standard
+	"pc2",			Standard
+	"pmu_int",		Standard
+	"pmu_scl",		I2C
+	"pmu_sda",		I2C
+	"rfst2g_mtsloten3g",	Standard
+	"rgmii_0_rx_ctl",	Standard
+	"rgmii_0_rxc",		Standard
+	"rgmii_0_rxd_0",	Standard
+	"rgmii_0_rxd_1",	Standard
+	"rgmii_0_rxd_2",	Standard
+	"rgmii_0_rxd_3",	Standard
+	"rgmii_0_tx_ctl",	Standard
+	"rgmii_0_txc",		Standard
+	"rgmii_0_txd_0",	Standard
+	"rgmii_0_txd_1",	Standard
+	"rgmii_0_txd_2",	Standard
+	"rgmii_0_txd_3",	Standard
+	"rgmii_1_rx_ctl",	Standard
+	"rgmii_1_rxc",		Standard
+	"rgmii_1_rxd_0",	Standard
+	"rgmii_1_rxd_1",	Standard
+	"rgmii_1_rxd_2",	Standard
+	"rgmii_1_rxd_3",	Standard
+	"rgmii_1_tx_ctl",	Standard
+	"rgmii_1_txc",		Standard
+	"rgmii_1_txd_0",	Standard
+	"rgmii_1_txd_1",	Standard
+	"rgmii_1_txd_2",	Standard
+	"rgmii_1_txd_3",	Standard
+	"rgmii_gpio_0",		Standard
+	"rgmii_gpio_1",		Standard
+	"rgmii_gpio_2",		Standard
+	"rgmii_gpio_3",		Standard
+	"rtxdata2g_txdata3g1",	Standard
+	"rtxen2g_txdata3g2",	Standard
+	"rxdata3g0",		Standard
+	"rxdata3g1",		Standard
+	"rxdata3g2",		Standard
+	"sdio1_clk",		Standard
+	"sdio1_cmd",		Standard
+	"sdio1_data_0",		Standard
+	"sdio1_data_1",		Standard
+	"sdio1_data_2",		Standard
+	"sdio1_data_3",		Standard
+	"sdio4_clk",		Standard
+	"sdio4_cmd",		Standard
+	"sdio4_data_0",		Standard
+	"sdio4_data_1",		Standard
+	"sdio4_data_2",		Standard
+	"sdio4_data_3",		Standard
+	"sim_clk",		Standard
+	"sim_data",		Standard
+	"sim_det",		Standard
+	"sim_resetn",		Standard
+	"sim2_clk",		Standard
+	"sim2_data",		Standard
+	"sim2_det",		Standard
+	"sim2_resetn",		Standard
+	"sri_c",		Standard
+	"sri_d",		Standard
+	"sri_e",		Standard
+	"ssp_extclk",		Standard
+	"ssp0_clk",		Standard
+	"ssp0_fs",		Standard
+	"ssp0_rxd",		Standard
+	"ssp0_txd",		Standard
+	"ssp2_clk",		Standard
+	"ssp2_fs_0",		Standard
+	"ssp2_fs_1",		Standard
+	"ssp2_fs_2",		Standard
+	"ssp2_fs_3",		Standard
+	"ssp2_rxd_0",		Standard
+	"ssp2_rxd_1",		Standard
+	"ssp2_txd_0",		Standard
+	"ssp2_txd_1",		Standard
+	"ssp3_clk",		Standard
+	"ssp3_fs",		Standard
+	"ssp3_rxd",		Standard
+	"ssp3_txd",		Standard
+	"ssp4_clk",		Standard
+	"ssp4_fs",		Standard
+	"ssp4_rxd",		Standard
+	"ssp4_txd",		Standard
+	"ssp5_clk",		Standard
+	"ssp5_fs",		Standard
+	"ssp5_rxd",		Standard
+	"ssp5_txd",		Standard
+	"ssp6_clk",		Standard
+	"ssp6_fs",		Standard
+	"ssp6_rxd",		Standard
+	"ssp6_txd",		Standard
+	"stat_1",		Standard
+	"stat_2",		Standard
+	"sysclken",		Standard
+	"traceclk",		Standard
+	"tracedt00",		Standard
+	"tracedt01",		Standard
+	"tracedt02",		Standard
+	"tracedt03",		Standard
+	"tracedt04",		Standard
+	"tracedt05",		Standard
+	"tracedt06",		Standard
+	"tracedt07",		Standard
+	"tracedt08",		Standard
+	"tracedt09",		Standard
+	"tracedt10",		Standard
+	"tracedt11",		Standard
+	"tracedt12",		Standard
+	"tracedt13",		Standard
+	"tracedt14",		Standard
+	"tracedt15",		Standard
+	"txdata3g0",		Standard
+	"txpwrind",		Standard
+	"uartb1_ucts",		Standard
+	"uartb1_urts",		Standard
+	"uartb1_urxd",		Standard
+	"uartb1_utxd",		Standard
+	"uartb2_urxd",		Standard
+	"uartb2_utxd",		Standard
+	"uartb3_ucts",		Standard
+	"uartb3_urts",		Standard
+	"uartb3_urxd",		Standard
+	"uartb3_utxd",		Standard
+	"uartb4_ucts",		Standard
+	"uartb4_urts",		Standard
+	"uartb4_urxd",		Standard
+	"uartb4_utxd",		Standard
+	"vc_cam1_scl",		I2C
+	"vc_cam1_sda",		I2C
+	"vc_cam2_scl",		I2C
+	"vc_cam2_sda",		I2C
+	"vc_cam3_scl",		I2C
+	"vc_cam3_sda",		I2C