Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

Pull input updates from Dmitry Torokhov:

 - three new touchscreen drivers: Hycon HY46XX, ILITEK Lego Series,
   and MStar MSG2638

 - a new driver for Azoteq IQS626A proximity and touch controller

 - addition of Amazon Game Controller to the list of devices handled
   by the xpad driver

 - Elan touchscreen driver will avoid binding to devices described as
   I2CHID compatible in ACPI tables

 - various driver fixes

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (56 commits)
  Input: xpad - add support for Amazon Game Controller
  Input: ili210x - add missing negation for touch indication on ili210x
  MAINTAINERS: repair reference in HYCON HY46XX TOUCHSCREEN SUPPORT
  Input: add driver for the Hycon HY46XX touchpanel series
  dt-bindings: touchscreen: Add HY46XX bindings
  dt-bindings: Add Hycon Technology vendor prefix
  Input: cyttsp - flag the device properly
  Input: cyttsp - set abs params for ABS_MT_TOUCH_MAJOR
  Input: cyttsp - drop the phys path
  Input: cyttsp - reduce reset pulse timings
  Input: cyttsp - error message on boot mode exit error
  Input: apbps2 - remove useless variable
  Input: mms114 - support MMS136
  Input: mms114 - convert bindings to YAML and extend
  Input: Add support for ILITEK Lego Series
  dt-bindings: input: touchscreen: ilitek_ts_i2c: Add bindings
  Input: add MStar MSG2638 touchscreen driver
  dt-bindings: input/touchscreen: add bindings for msg2638
  Input: silead - add workaround for x86 BIOS-es which bring the chip up in a stuck state
  Input: elants_i2c - do not bind to i2c-hid compatible ACPI instantiated devices
  ...

10 files changed, 1300 insertions, 122 deletions

diff --git a/Documentation/devicetree/bindings/input/atmel,maxtouch.yaml b/Documentation/devicetree/bindings/input/atmel,maxtouch.yaml
index 8c6418f76e94..3ec579d63570 100644
--- a/Documentation/devicetree/bindings/input/atmel,maxtouch.yaml
+++ b/Documentation/devicetree/bindings/input/atmel,maxtouch.yaml
@@ -39,6 +39,13 @@ properties:
       (active low). The line must be flagged with
       GPIO_ACTIVE_LOW.
 
+  wake-gpios:
+    maxItems: 1
+    description:
+      Optional GPIO specifier for the touchscreen's wake pin
+      (active low). The line must be flagged with
+      GPIO_ACTIVE_LOW.
+
   linux,gpio-keymap:
     $ref: /schemas/types.yaml#/definitions/uint32-array
     description: |
@@ -53,6 +60,29 @@ properties:
       or experiment to determine which bit corresponds to which input. Use
       KEY_RESERVED for unused padding values.
 
+  atmel,wakeup-method:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      The WAKE line is an active-low input that is used to wake up the touch
+      controller from deep-sleep mode before communication with the controller
+      could be started. This optional feature used to minimize current
+      consumption when the controller is in deep sleep mode. This feature is
+      relevant only to some controller families, like mXT1386 controller for
+      example.
+
+      The WAKE pin can be connected in one of the following ways:
+       1) left permanently low
+       2) connected to the I2C-compatible SCL pin
+       3) connected to a GPIO pin on the host
+    enum:
+      - 0 # ATMEL_MXT_WAKEUP_NONE
+      - 1 # ATMEL_MXT_WAKEUP_I2C_SCL
+      - 2 # ATMEL_MXT_WAKEUP_GPIO
+    default: 0
+
+  wakeup-source:
+    type: boolean
+
 required:
   - compatible
   - reg
@@ -63,6 +93,7 @@ additionalProperties: false
 examples:
   - |
     #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/input/atmel-maxtouch.h>
     #include <dt-bindings/gpio/gpio.h>
     i2c {
       #address-cells = <1>;
@@ -75,6 +106,7 @@ examples:
         reset-gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
         vdda-supply = <&ab8500_ldo_aux2_reg>;
         vdd-supply = <&ab8500_ldo_aux5_reg>;
+        atmel,wakeup-method = <ATMEL_MXT_WAKEUP_I2C_SCL>;
       };
     };
 
diff --git a/Documentation/devicetree/bindings/input/iqs626a.yaml b/Documentation/devicetree/bindings/input/iqs626a.yaml
new file mode 100644
index 000000000000..0cb736c541c9
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/iqs626a.yaml
@@ -0,0 +1,843 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/input/iqs626a.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Azoteq IQS626A Capacitive Touch Controller
+
+maintainers:
+  - Jeff LaBundy <jeff@labundy.com>
+
+description: |
+  The Azoteq IQS626A is a 14-channel capacitive touch controller that features
+  additional Hall-effect and inductive sensing capabilities.
+
+  Link to datasheet: https://www.azoteq.com/
+
+allOf:
+  - $ref: touchscreen/touchscreen.yaml#
+
+properties:
+  compatible:
+    const: azoteq,iqs626a
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+  azoteq,suspend-mode:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1, 2, 3]
+    default: 0
+    description: |
+      Specifies the power mode during suspend as follows:
+      0: Automatic (same as normal runtime, i.e. suspend/resume disabled)
+      1: Low power (all sensing at a reduced reporting rate)
+      2: Ultra-low power (ULP channel proximity sensing)
+      3: Halt (no sensing)
+
+  azoteq,clk-div:
+    type: boolean
+    description: Divides the device's core clock by a factor of 4.
+
+  azoteq,ulp-enable:
+    type: boolean
+    description:
+      Permits the device to automatically enter ultra-low-power mode from low-
+      power mode.
+
+  azoteq,ulp-update:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1, 2, 3, 4, 5, 6, 7]
+    default: 3
+    description: |
+      Specifies the rate at which the trackpad, generic and Hall channels are
+      updated during ultra-low-power mode as follows:
+      0: 8
+      1: 13
+      2: 28
+      3: 54
+      4: 89
+      5: 135
+      6: 190
+      7: 256
+
+  azoteq,ati-band-disable:
+    type: boolean
+    description: Disables the ATI band check.
+
+  azoteq,ati-lp-only:
+    type: boolean
+    description: Limits automatic ATI to low-power mode.
+
+  azoteq,gpio3-select:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1, 2, 3, 4, 5, 6, 7]
+    default: 1
+    description: |
+      Selects the channel or group of channels for which the GPIO3 pin
+      represents touch state as follows:
+      0: None
+      1: ULP channel
+      2: Trackpad
+      3: Trackpad
+      4: Generic channel 0
+      5: Generic channel 1
+      6: Generic channel 2
+      7: Hall channel
+
+  azoteq,reseed-select:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1, 2, 3]
+    default: 0
+    description: |
+      Specifies the event(s) that prompt the device to reseed (i.e. reset the
+      long-term average) of an associated channel as follows:
+      0: None
+      1: Proximity
+      2: Proximity or touch
+      3: Proximity, touch or deep touch
+
+  azoteq,thresh-extend:
+    type: boolean
+    description: Multiplies all touch and deep-touch thresholds by 4.
+
+  azoteq,tracking-enable:
+    type: boolean
+    description:
+      Enables all associated channels to track their respective reference
+      channels.
+
+  azoteq,reseed-offset:
+    type: boolean
+    description:
+      Applies an 8-count offset to all long-term averages upon either ATI or
+      reseed events.
+
+  azoteq,rate-np-ms:
+    minimum: 0
+    maximum: 255
+    default: 150
+    description: Specifies the report rate (in ms) during normal-power mode.
+
+  azoteq,rate-lp-ms:
+    minimum: 0
+    maximum: 255
+    default: 150
+    description: Specifies the report rate (in ms) during low-power mode.
+
+  azoteq,rate-ulp-ms:
+    multipleOf: 16
+    minimum: 0
+    maximum: 4080
+    default: 0
+    description: Specifies the report rate (in ms) during ultra-low-power mode.
+
+  azoteq,timeout-pwr-ms:
+    multipleOf: 512
+    minimum: 0
+    maximum: 130560
+    default: 2560
+    description:
+      Specifies the length of time (in ms) to wait for an event before moving
+      from normal-power mode to low-power mode, or (if 'azoteq,ulp-enable' is
+      present) from low-power mode to ultra-low-power mode.
+
+  azoteq,timeout-lta-ms:
+    multipleOf: 512
+    minimum: 0
+    maximum: 130560
+    default: 40960
+    description:
+      Specifies the length of time (in ms) to wait before resetting the long-
+      term average of all channels. Specify the maximum timeout to disable it
+      altogether.
+
+  touchscreen-inverted-x: true
+  touchscreen-inverted-y: true
+  touchscreen-swapped-x-y: true
+
+patternProperties:
+  "^ulp-0|generic-[0-2]|hall$":
+    type: object
+    description:
+      Represents a single sensing channel. A channel is active if defined and
+      inactive otherwise.
+
+    properties:
+      azoteq,ati-exclude:
+        type: boolean
+        description:
+          Prevents the channel from participating in an ATI event that is
+          manually triggered during initialization.
+
+      azoteq,reseed-disable:
+        type: boolean
+        description:
+          Prevents the channel from being reseeded if the long-term average
+          timeout (defined in 'azoteq,timeout-lta') expires.
+
+      azoteq,meas-cap-decrease:
+        type: boolean
+        description:
+          Decreases the internal measurement capacitance from 60 pF to 15 pF.
+
+      azoteq,rx-inactive:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [0, 1, 2]
+        default: 0
+        description: |
+          Specifies how inactive CRX pins are to be terminated as follows:
+          0: VSS
+          1: Floating
+          2: VREG (generic channels only)
+
+      azoteq,linearize:
+        type: boolean
+        description:
+          Enables linearization of the channel's counts (generic and Hall
+          channels) or inverts the polarity of the channel's proximity or
+          touch states (ULP channel).
+
+      azoteq,dual-direction:
+        type: boolean
+        description:
+          Specifies that the channel's long-term average is to freeze in the
+          presence of either increasing or decreasing counts, thereby permit-
+          ting events to be reported in either direction.
+
+      azoteq,filt-disable:
+        type: boolean
+        description: Disables raw count filtering for the channel.
+
+      azoteq,ati-mode:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [0, 1, 2, 3]
+        description: |
+          Specifies the channel's ATI mode as follows:
+          0: Disabled
+          1: Semi-partial
+          2: Partial
+          3: Full
+
+          The default value is a function of the channel and the device's reset
+          user interface (RUI); reference the datasheet for further information
+          about the available RUI options.
+
+      azoteq,ati-base:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [75, 100, 150, 200]
+        description:
+          Specifies the channel's ATI base. The default value is a function
+          of the channel and the device's RUI.
+
+      azoteq,ati-target:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        multipleOf: 32
+        minimum: 0
+        maximum: 2016
+        description:
+          Specifies the channel's ATI target. The default value is a function
+          of the channel and the device's RUI.
+
+      azoteq,cct-increase:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 16
+        default: 0
+        description:
+          Specifies the degree to which the channel's charge cycle time is to
+          be increased, with 0 representing no increase. The maximum value is
+          limited to 4 in the case of the ULP channel, and the property is un-
+          available entirely in the case of the Hall channel.
+
+      azoteq,proj-bias:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [0, 1, 2, 3]
+        default: 0
+        description: |
+          Specifies the bias current applied during projected-capacitance
+          sensing as follows:
+          0: 2.5 uA
+          1: 5 uA
+          2: 10 uA
+          3: 20 uA
+
+          This property is unavailable in the case of the Hall channel.
+
+      azoteq,sense-freq:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [0, 1, 2, 3]
+        description: |
+          Specifies the channel's sensing frequency as follows (parenthesized
+          numbers represent the frequency if 'azoteq,clk-div' is present):
+          0: 4 MHz (1 MHz)
+          1: 2 MHz (500 kHz)
+          2: 1 MHz (250 kHz)
+          3: 500 kHz (125 kHz)
+
+          This property is unavailable in the case of the Hall channel. The
+          default value is a function of the channel and the device's RUI.
+
+      azoteq,ati-band-tighten:
+        type: boolean
+        description:
+          Tightens the ATI band from 1/8 to 1/16 of the desired target (ULP and
+          generic channels only).
+
+      azoteq,proj-enable:
+        type: boolean
+        description: Enables projected-capacitance sensing (ULP channel only).
+
+      azoteq,filt-str-np-cnt:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [0, 1, 2, 3]
+        default: 0
+        description:
+          Specifies the raw count filter strength during normal-power mode (ULP
+          and generic channels only).
+
+      azoteq,filt-str-lp-cnt:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [0, 1, 2, 3]
+        default: 0
+        description:
+          Specifies the raw count filter strength during low-power mode (ULP and
+          generic channels only).
+
+      azoteq,filt-str-np-lta:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [0, 1, 2, 3]
+        default: 0
+        description:
+          Specifies the long-term average filter strength during normal-power
+          mode (ULP and generic channels only).
+
+      azoteq,filt-str-lp-lta:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [0, 1, 2, 3]
+        default: 0
+        description:
+          Specifies the long-term average filter strength during low-power mode
+          (ULP and generic channels only).
+
+      azoteq,rx-enable:
+        $ref: /schemas/types.yaml#/definitions/uint32-array
+        minItems: 1
+        maxItems: 8
+        items:
+          minimum: 0
+          maximum: 7
+        description:
+          Specifies the CRX pin(s) associated with the channel.
+
+          This property is unavailable in the case of the Hall channel. The
+          default value is a function of the channel and the device's RUI.
+
+      azoteq,tx-enable:
+        $ref: /schemas/types.yaml#/definitions/uint32-array
+        minItems: 1
+        maxItems: 8
+        items:
+          minimum: 0
+          maximum: 7
+        description:
+          Specifies the TX pin(s) associated with the channel.
+
+          This property is unavailable in the case of the Hall channel. The
+          default value is a function of the channel and the device's RUI.
+
+      azoteq,local-cap-size:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [0, 1, 2, 3, 4]
+        default: 0
+        description: |
+          Specifies the capacitance to be added to the channel as follows:
+          0: 0 pF
+          1: 0.5 pF
+          2: 1.0 pF
+          3: 1.5 pF
+          4: 2.0 pF
+
+          This property is unavailable in the case of the ULP or Hall channels.
+
+      azoteq,sense-mode:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [0, 1, 8, 9, 12, 14, 15]
+        description: |
+          Specifies the channel's sensing mode as follows:
+          0:  Self capacitance
+          1:  Projected capacitance
+          8:  Self inductance
+          9:  Mutual inductance
+          12: External
+          14: Hall effect
+          15: Temperature
+
+          This property is unavailable in the case of the ULP or Hall channels.
+          The default value is a function of the channel and the device's RUI.
+
+      azoteq,tx-freq:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [0, 1, 2, 3]
+        default: 0
+        description: |
+          Specifies the inductive sensing excitation frequency as follows
+          (parenthesized numbers represent the frequency if 'azoteq,clk-div'
+          is present):
+          0: 16 MHz (4 MHz)
+          1: 8 MHz (2 MHz)
+          2: 4 MHz (1 MHz)
+          3: 2 MHz (500 kHz)
+
+          This property is unavailable in the case of the ULP or Hall channels.
+
+      azoteq,invert-enable:
+        type: boolean
+        description:
+          Inverts the polarity of the states reported for proximity, touch and
+          deep-touch events relative to their respective thresholds (generic
+          channels only).
+
+      azoteq,comp-disable:
+        type: boolean
+        description:
+          Disables compensation for the channel (generic channels only).
+
+      azoteq,static-enable:
+        type: boolean
+        description:
+          Enables the static front-end for the channel (generic channels only).
+
+      azoteq,assoc-select:
+        $ref: /schemas/types.yaml#/definitions/string-array
+        minItems: 1
+        maxItems: 6
+        items:
+          enum:
+            - ulp-0
+            - trackpad-3x2
+            - trackpad-3x3
+            - generic-0
+            - generic-1
+            - generic-2
+            - hall
+        description:
+          Specifies the associated channels for which the channel serves as a
+          reference channel. By default, no channels are selected. This prop-
+          erty is only available for the generic channels.
+
+      azoteq,assoc-weight:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 255
+        default: 0
+        description:
+          Specifies the channel's impact weight if it acts as an associated
+          channel (0 = 0% impact, 255 = 200% impact). This property is only
+          available for the generic channels.
+
+    patternProperties:
+      "^event-(prox|touch|deep)(-alt)?$":
+        type: object
+        description:
+          Represents a proximity, touch or deep-touch event reported by the
+          channel in response to a decrease in counts. Node names suffixed with
+          '-alt' instead correspond to an increase in counts.
+
+          By default, the long-term average tracks an increase in counts such
+          that only events corresponding to a decrease in counts are reported
+          (refer to the datasheet for more information).
+
+          Specify 'azoteq,dual-direction' to freeze the long-term average when
+          the counts increase or decrease such that events of either direction
+          can be reported. Alternatively, specify 'azoteq,invert-enable' to in-
+          vert the polarity of the states reported by the channel.
+
+          Complementary events (e.g. event-touch and event-touch-alt) can both
+          be present and specify different key or switch codes, but not differ-
+          ent thresholds or hysteresis (if applicable).
+
+          Proximity events are unavailable in the case of the Hall channel, and
+          deep-touch events are only available for the generic channels. Unless
+          otherwise specified, default values are a function of the channel and
+          the device's RUI.
+
+        properties:
+          azoteq,thresh:
+            $ref: /schemas/types.yaml#/definitions/uint32
+            minimum: 0
+            maximum: 255
+            description: Specifies the threshold for the event.
+
+          azoteq,hyst:
+            $ref: /schemas/types.yaml#/definitions/uint32
+            minimum: 0
+            maximum: 15
+            description:
+              Specifies the hysteresis for the event (touch and deep-touch
+              events only).
+
+          linux,code:
+            $ref: /schemas/types.yaml#/definitions/uint32
+            description: Numeric key or switch code associated with the event.
+
+          linux,input-type:
+            $ref: /schemas/types.yaml#/definitions/uint32
+            enum: [1, 5]
+            description:
+              Specifies whether the event is to be interpreted as a key (1) or
+              a switch (5). By default, Hall-channel events are interpreted as
+              switches and all others are interpreted as keys.
+
+        dependencies:
+          linux,input-type: ["linux,code"]
+
+        additionalProperties: false
+
+    dependencies:
+      azoteq,assoc-weight: ["azoteq,assoc-select"]
+
+    additionalProperties: false
+
+  "^trackpad-3x[2-3]$":
+    type: object
+    description:
+      Represents all channels associated with the trackpad. The channels are
+      collectively active if the trackpad is defined and inactive otherwise.
+
+    properties:
+      azoteq,ati-exclude:
+        type: boolean
+        description:
+          Prevents the trackpad channels from participating in an ATI event
+          that is manually triggered during initialization.
+
+      azoteq,reseed-disable:
+        type: boolean
+        description:
+          Prevents the trackpad channels from being reseeded if the long-term
+          average timeout (defined in 'azoteq,timeout-lta') expires.
+
+      azoteq,meas-cap-decrease:
+        type: boolean
+        description:
+          Decreases the internal measurement capacitance from 60 pF to 15 pF.
+
+      azoteq,rx-inactive:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [0, 1]
+        default: 0
+        description: |
+          Specifies how inactive CRX pins are to be terminated as follows:
+          0: VSS
+          1: Floating
+
+      azoteq,linearize:
+        type: boolean
+        description: Inverts the polarity of the trackpad's touch state.
+
+      azoteq,dual-direction:
+        type: boolean
+        description:
+          Specifies that the trackpad's long-term averages are to freeze in
+          the presence of either increasing or decreasing counts, thereby
+          permitting events to be reported in either direction.
+
+      azoteq,filt-disable:
+        type: boolean
+        description: Disables raw count filtering for the trackpad channels.
+
+      azoteq,ati-mode:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [0, 1, 2, 3]
+        default: 0
+        description: |
+          Specifies the trackpad's ATI mode as follows:
+          0: Disabled
+          1: Semi-partial
+          2: Partial
+          3: Full
+
+      azoteq,ati-base:
+        $ref: /schemas/types.yaml#/definitions/uint32-array
+        minItems: 6
+        maxItems: 9
+        items:
+          minimum: 45
+          maximum: 300
+        default: [45, 45, 45, 45, 45, 45, 45, 45, 45]
+        description: Specifies each individual trackpad channel's ATI base.
+
+      azoteq,ati-target:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        multipleOf: 32
+        minimum: 0
+        maximum: 2016
+        default: 0
+        description: Specifies the trackpad's ATI target.
+
+      azoteq,cct-increase:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 4
+        default: 0
+        description:
+          Specifies the degree to which the trackpad's charge cycle time is to
+          be increased, with 0 representing no increase.
+
+      azoteq,proj-bias:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [0, 1, 2, 3]
+        default: 0
+        description: |
+          Specifies the bias current applied during projected-capacitance
+          sensing as follows:
+          0: 2.5 uA
+          1: 5 uA
+          2: 10 uA
+          3: 20 uA
+
+      azoteq,sense-freq:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [0, 1, 2, 3]
+        default: 0
+        description: |
+          Specifies the trackpad's sensing frequency as follows (parenthesized
+          numbers represent the frequency if 'azoteq,clk-div' is present):
+          0: 4 MHz (1 MHz)
+          1: 2 MHz (500 kHz)
+          2: 1 MHz (250 kHz)
+          3: 500 kHz (125 kHz)
+
+      azoteq,ati-band-tighten:
+        type: boolean
+        description:
+          Tightens the ATI band from 1/8 to 1/16 of the desired target.
+
+      azoteq,thresh:
+        $ref: /schemas/types.yaml#/definitions/uint32-array
+        minItems: 6
+        maxItems: 9
+        items:
+          minimum: 0
+          maximum: 255
+        default: [0, 0, 0, 0, 0, 0, 0, 0, 0]
+        description:
+          Specifies each individual trackpad channel's touch threshold.
+
+      azoteq,hyst:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 15
+        default: 0
+        description: Specifies the trackpad's touch hysteresis.
+
+      azoteq,lta-update:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [0, 1, 2, 3, 4, 5, 6, 7]
+        default: 0
+        description: |
+          Specifies the update rate of the trackpad's long-term average during
+          ultra-low-power mode as follows:
+          0: 2
+          1: 4
+          2: 8
+          3: 16
+          4: 32
+          5: 64
+          6: 128
+          7: 255
+
+      azoteq,filt-str-trackpad:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [0, 1, 2, 3]
+        default: 0
+        description: Specifies the trackpad coordinate filter strength.
+
+      azoteq,filt-str-np-cnt:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [0, 1, 2, 3]
+        default: 0
+        description:
+          Specifies the raw count filter strength during normal-power mode.
+
+      azoteq,filt-str-lp-cnt:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [0, 1, 2, 3]
+        default: 0
+        description:
+          Specifies the raw count filter strength during low-power mode.
+
+      linux,keycodes:
+        $ref: /schemas/types.yaml#/definitions/uint32-array
+        minItems: 1
+        maxItems: 6
+        description: |
+          Specifies the numeric keycodes associated with each available gesture
+          in the following order (enter 0 for unused gestures):
+          0: Positive flick or swipe in X direction
+          1: Negative flick or swipe in X direction
+          2: Positive flick or swipe in Y direction
+          3: Negative flick or swipe in Y direction
+          4: Tap
+          5: Hold
+
+      azoteq,gesture-swipe:
+        type: boolean
+        description:
+          Directs the device to interpret axial gestures as a swipe (finger
+          remains on trackpad) instead of a flick (finger leaves trackpad).
+
+      azoteq,timeout-tap-ms:
+        multipleOf: 16
+        minimum: 0
+        maximum: 4080
+        default: 0
+        description:
+          Specifies the length of time (in ms) within which a trackpad touch
+          must be released in order to be interpreted as a tap.
+
+      azoteq,timeout-swipe-ms:
+        multipleOf: 16
+        minimum: 0
+        maximum: 4080
+        default: 0
+        description:
+          Specifies the length of time (in ms) within which an axial gesture
+          must be completed in order to be interpreted as a flick or swipe.
+
+      azoteq,thresh-swipe:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 255
+        default: 0
+        description:
+          Specifies the number of points across which an axial gesture must
+          travel in order to be interpreted as a flick or swipe.
+
+    dependencies:
+      azoteq,gesture-swipe: ["linux,keycodes"]
+      azoteq,timeout-tap-ms: ["linux,keycodes"]
+      azoteq,timeout-swipe-ms: ["linux,keycodes"]
+      azoteq,thresh-swipe: ["linux,keycodes"]
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - "#address-cells"
+  - "#size-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/input/input.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            iqs626a@44 {
+                    #address-cells = <1>;
+                    #size-cells = <0>;
+
+                    compatible = "azoteq,iqs626a";
+                    reg = <0x44>;
+                    interrupt-parent = <&gpio>;
+                    interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+
+                    azoteq,rate-np-ms = <16>;
+                    azoteq,rate-lp-ms = <160>;
+
+                    azoteq,timeout-pwr-ms = <2560>;
+                    azoteq,timeout-lta-ms = <32768>;
+
+                    ulp-0 {
+                            azoteq,meas-cap-decrease;
+
+                            azoteq,ati-base = <75>;
+                            azoteq,ati-target = <1024>;
+
+                            azoteq,rx-enable = <2>, <3>, <4>,
+                                               <5>, <6>, <7>;
+
+                            event-prox {
+                                    linux,code = <KEY_POWER>;
+                            };
+                    };
+
+                    trackpad-3x3 {
+                            azoteq,filt-str-np-cnt = <1>;
+                            azoteq,filt-str-lp-cnt = <1>;
+
+                            azoteq,hyst = <4>;
+                            azoteq,thresh = <35>, <40>, <40>,
+                                            <38>, <33>, <38>,
+                                            <35>, <35>, <35>;
+
+                            azoteq,ati-mode = <3>;
+                            azoteq,ati-base = <195>, <195>, <195>,
+                                              <195>, <195>, <195>,
+                                              <195>, <195>, <195>;
+                            azoteq,ati-target = <512>;
+
+                            azoteq,proj-bias = <1>;
+                            azoteq,sense-freq = <2>;
+
+                            linux,keycodes = <KEY_VOLUMEUP>,
+                                             <KEY_VOLUMEDOWN>,
+                                             <KEY_NEXTSONG>,
+                                             <KEY_PREVIOUSSONG>,
+                                             <KEY_PLAYPAUSE>,
+                                             <KEY_STOPCD>;
+
+                            azoteq,gesture-swipe;
+                            azoteq,timeout-swipe-ms = <800>;
+                            azoteq,timeout-tap-ms = <400>;
+                            azoteq,thresh-swipe = <40>;
+                    };
+
+                    /*
+                     * Preserve the default register settings for
+                     * the temperature-tracking channel leveraged
+                     * by reset user interface (RUI) 1.
+                     *
+                     * Scalar properties (e.g. ATI mode) are left
+                     * untouched by simply omitting them; boolean
+                     * properties must be specified explicitly as
+                     * needed.
+                     */
+                    generic-2 {
+                            azoteq,reseed-disable;
+                            azoteq,meas-cap-decrease;
+                            azoteq,dual-direction;
+                            azoteq,comp-disable;
+                            azoteq,static-enable;
+                    };
+
+                    hall {
+                            azoteq,reseed-disable;
+                            azoteq,meas-cap-decrease;
+
+                            event-touch {
+                                    linux,code = <SW_LID>;
+                            };
+                    };
+            };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/input/touchscreen/azoteq,iqs5xx.yaml b/Documentation/devicetree/bindings/input/touchscreen/azoteq,iqs5xx.yaml
new file mode 100644
index 000000000000..b5f377215c09
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/azoteq,iqs5xx.yaml
@@ -0,0 +1,75 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/input/touchscreen/azoteq,iqs5xx.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Azoteq IQS550/572/525 Trackpad/Touchscreen Controller
+
+maintainers:
+  - Jeff LaBundy <jeff@labundy.com>
+
+description: |
+  The Azoteq IQS550, IQS572 and IQS525 trackpad and touchscreen controllers
+  employ projected-capacitance sensing and can track up to five independent
+  contacts.
+
+  Link to datasheet: https://www.azoteq.com/
+
+allOf:
+  - $ref: touchscreen.yaml#
+
+properties:
+  compatible:
+    enum:
+      - azoteq,iqs550
+      - azoteq,iqs572
+      - azoteq,iqs525
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  reset-gpios:
+    maxItems: 1
+
+  wakeup-source: true
+
+  touchscreen-size-x: true
+  touchscreen-size-y: true
+  touchscreen-inverted-x: true
+  touchscreen-inverted-y: true
+  touchscreen-swapped-x-y: true
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            touchscreen@74 {
+                    compatible = "azoteq,iqs550";
+                    reg = <0x74>;
+                    interrupt-parent = <&gpio>;
+                    interrupts = <27 IRQ_TYPE_LEVEL_HIGH>;
+                    reset-gpios = <&gpio 22 (GPIO_ACTIVE_LOW |
+                                             GPIO_PUSH_PULL)>;
+
+                    touchscreen-size-x = <800>;
+                    touchscreen-size-y = <480>;
+            };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/input/touchscreen/hycon,hy46xx.yaml b/Documentation/devicetree/bindings/input/touchscreen/hycon,hy46xx.yaml
new file mode 100644
index 000000000000..942562f1e45b
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/hycon,hy46xx.yaml
@@ -0,0 +1,119 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/input/touchscreen/hycon,hy46xx.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Hycon HY46XX series touchscreen controller bindings
+
+description: |
+  There are 6 variants of the chip for various touch panel sizes and cover lens material
+   Glass: 0.3mm--4.0mm
+    PET/PMMA: 0.2mm--2.0mm
+    HY4613(B)-N048  < 6"
+    HY4614(B)-N068  7" .. 10.1"
+    HY4621-NS32  < 5"
+    HY4623-NS48  5.1" .. 7"
+   Glass: 0.3mm--8.0mm
+    PET/PMMA: 0.2mm--4.0mm
+    HY4633(B)-N048  < 6"
+    HY4635(B)-N048  < 7" .. 10.1"
+
+maintainers:
+  - Giulio Benetti <giulio.benetti@benettiengineering.com>
+
+allOf:
+  - $ref: touchscreen.yaml#
+
+properties:
+  compatible:
+    enum:
+      - hycon,hy4613
+      - hycon,hy4614
+      - hycon,hy4621
+      - hycon,hy4623
+      - hycon,hy4633
+      - hycon,hy4635
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  reset-gpios:
+    maxItems: 1
+
+  vcc-supply: true
+
+  hycon,threshold:
+    description: Allows setting the sensitivity in the range from 0 to 255.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 255
+
+  hycon,glove-enable:
+    type: boolean
+    description: Allows enabling glove setting.
+
+  hycon,report-speed-hz:
+    description: Allows setting the report speed in Hertz.
+    minimum: 1
+    maximum: 255
+
+  hycon,noise-filter-enable:
+    type: boolean
+    description: Allows enabling power noise filter.
+
+  hycon,filter-data:
+    description: Allows setting how many samples throw before reporting touch
+                 in the range from 0 to 5.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 5
+
+  hycon,gain:
+    description: Allows setting the sensitivity distance in the range from 0 to 5.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 5
+
+  hycon,edge-offset:
+    description: Allows setting the edge compensation in the range from 0 to 16.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 16
+
+  touchscreen-size-x: true
+  touchscreen-size-y: true
+  touchscreen-fuzz-x: true
+  touchscreen-fuzz-y: true
+  touchscreen-inverted-x: true
+  touchscreen-inverted-y: true
+  touchscreen-swapped-x-y: true
+  interrupt-controller: true
+
+additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+      touchscreen@1c {
+        compatible = "hycon,hy4633";
+        reg = <0x1c>;
+        interrupt-parent = <&gpio2>;
+        interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+        reset-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
+      };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/input/touchscreen/ilitek_ts_i2c.yaml b/Documentation/devicetree/bindings/input/touchscreen/ilitek_ts_i2c.yaml
new file mode 100644
index 000000000000..a190e7baac31
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/ilitek_ts_i2c.yaml
@@ -0,0 +1,73 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/input/touchscreen/ilitek_ts_i2c.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Ilitek I2C Touchscreen Controller
+
+maintainers:
+  - Dmitry Torokhov <dmitry.torokhov@gmail.com>
+
+allOf:
+  - $ref: touchscreen.yaml#
+
+properties:
+  compatible:
+    enum:
+      - ilitek,ili2130
+      - ilitek,ili2131
+      - ilitek,ili2132
+      - ilitek,ili2316
+      - ilitek,ili2322
+      - ilitek,ili2323
+      - ilitek,ili2326
+      - ilitek,ili2520
+      - ilitek,ili2521
+
+  reg:
+    const: 0x41
+
+  interrupts:
+    maxItems: 1
+
+  reset-gpios:
+    maxItems: 1
+
+  wakeup-source:
+    type: boolean
+    description: touchscreen can be used as a wakeup source.
+
+  touchscreen-size-x: true
+  touchscreen-size-y: true
+  touchscreen-inverted-x: true
+  touchscreen-inverted-y: true
+  touchscreen-swapped-x-y: true
+
+additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - reset-gpios
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/gpio/gpio.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        touchscreen@41 {
+            compatible = "ilitek,ili2520";
+            reg = <0x41>;
+
+            interrupt-parent = <&gpio1>;
+            interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+            reset-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+            touchscreen-inverted-y;
+            wakeup-source;
+        };
+    };
diff --git a/Documentation/devicetree/bindings/input/touchscreen/iqs5xx.txt b/Documentation/devicetree/bindings/input/touchscreen/iqs5xx.txt
deleted file mode 100644
index efa0820e2469..000000000000
--- a/Documentation/devicetree/bindings/input/touchscreen/iqs5xx.txt
+++ /dev/null
@@ -1,80 +0,0 @@
-Azoteq IQS550/572/525 Trackpad/Touchscreen Controller
-
-Required properties:
-
-- compatible			: Must be equal to one of the following:
-				  "azoteq,iqs550"
-				  "azoteq,iqs572"
-				  "azoteq,iqs525"
-
-- reg				: I2C slave address for the device.
-
-- interrupts			: GPIO to which the device's active-high RDY
-				  output is connected (see [0]).
-
-- reset-gpios			: GPIO to which the device's active-low NRST
-				  input is connected (see [1]).
-
-Optional properties:
-
-- touchscreen-min-x		: See [2].
-
-- touchscreen-min-y		: See [2].
-
-- touchscreen-size-x		: See [2]. If this property is omitted, the
-				  maximum x-coordinate is specified by the
-				  device's "X Resolution" register.
-
-- touchscreen-size-y		: See [2]. If this property is omitted, the
-				  maximum y-coordinate is specified by the
-				  device's "Y Resolution" register.
-
-- touchscreen-max-pressure	: See [2]. Pressure is expressed as the sum of
-				  the deltas across all channels impacted by a
-				  touch event. A channel's delta is calculated
-				  as its count value minus a reference, where
-				  the count value is inversely proportional to
-				  the channel's capacitance.
-
-- touchscreen-fuzz-x		: See [2].
-
-- touchscreen-fuzz-y		: See [2].
-
-- touchscreen-fuzz-pressure	: See [2].
-
-- touchscreen-inverted-x	: See [2]. Inversion is applied relative to that
-				  which may already be specified by the device's
-				  FLIP_X and FLIP_Y register fields.
-
-- touchscreen-inverted-y	: See [2]. Inversion is applied relative to that
-				  which may already be specified by the device's
-				  FLIP_X and FLIP_Y register fields.
-
-- touchscreen-swapped-x-y	: See [2]. Swapping is applied relative to that
-				  which may already be specified by the device's
-				  SWITCH_XY_AXIS register field.
-
-[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
-[1]: Documentation/devicetree/bindings/gpio/gpio.txt
-[2]: Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt
-
-Example:
-
-	&i2c1 {
-		/* ... */
-
-		touchscreen@74 {
-			compatible = "azoteq,iqs550";
-			reg = <0x74>;
-			interrupt-parent = <&gpio>;
-			interrupts = <17 4>;
-			reset-gpios = <&gpio 27 1>;
-
-			touchscreen-size-x = <640>;
-			touchscreen-size-y = <480>;
-
-			touchscreen-max-pressure = <16000>;
-		};
-
-		/* ... */
-	};
diff --git a/Documentation/devicetree/bindings/input/touchscreen/melfas,mms114.yaml b/Documentation/devicetree/bindings/input/touchscreen/melfas,mms114.yaml
new file mode 100644
index 000000000000..62366886fb3e
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/melfas,mms114.yaml
@@ -0,0 +1,87 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/input/touchscreen/melfas,mms114.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Melfas MMS114 family touchscreen controller bindings
+
+maintainers:
+  - Linus Walleij <linus.walleij@linaro.org>
+
+allOf:
+  - $ref: touchscreen.yaml#
+
+properties:
+  $nodename:
+    pattern: "^touchscreen(@.*)?$"
+
+  compatible:
+    items:
+      - enum:
+          - melfas,mms114
+          - melfas,mms134s
+          - melfas,mms136
+          - melfas,mms152
+          - melfas,mms345l
+
+  reg:
+    description: I2C address
+
+  clock-frequency:
+    description: I2C client clock frequency, defined for host
+    minimum: 100000
+    maximum: 400000
+
+  interrupts:
+    maxItems: 1
+
+  avdd-supply:
+    description: Analog power supply regulator on AVDD pin
+
+  vdd-supply:
+    description: Digital power supply regulator on VDD pin
+
+  touchscreen-size-x: true
+  touchscreen-size-y: true
+  touchscreen-fuzz-x: true
+  touchscreen-fuzz-y: true
+  touchscreen-fuzz-pressure: true
+  touchscreen-inverted-x: true
+  touchscreen-inverted-y: true
+  touchscreen-swapped-x-y: true
+  touchscreen-max-pressure: true
+
+additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - touchscreen-size-x
+  - touchscreen-size-y
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+      touchscreen@48 {
+        compatible = "melfas,mms114";
+        reg = <0x48>;
+        interrupt-parent = <&gpio>;
+        interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+        avdd-supply = <&ldo1_reg>;
+        vdd-supply = <&ldo2_reg>;
+        touchscreen-size-x = <720>;
+        touchscreen-size-y = <1280>;
+        touchscreen-fuzz-x = <10>;
+        touchscreen-fuzz-y = <10>;
+        touchscreen-fuzz-pressure = <10>;
+        touchscreen-inverted-x;
+        touchscreen-inverted-y;
+      };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/input/touchscreen/mms114.txt b/Documentation/devicetree/bindings/input/touchscreen/mms114.txt
deleted file mode 100644
index 707234cfd7e6..000000000000
--- a/Documentation/devicetree/bindings/input/touchscreen/mms114.txt
+++ /dev/null
@@ -1,42 +0,0 @@
-* MELFAS MMS114/MMS152/MMS345L touchscreen controller
-
-Required properties:
-- compatible: should be one of:
-	- "melfas,mms114"
-	- "melfas,mms152"
-	- "melfas,mms345l"
-- reg: I2C address of the chip
-- interrupts: interrupt to which the chip is connected
-- touchscreen-size-x: See [1]
-- touchscreen-size-y: See [1]
-
-Optional properties:
-- touchscreen-fuzz-x: See [1]
-- touchscreen-fuzz-y: See [1]
-- touchscreen-fuzz-pressure: See [1]
-- touchscreen-inverted-x: See [1]
-- touchscreen-inverted-y: See [1]
-- touchscreen-swapped-x-y: See [1]
-
-[1]: Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt
-
-Example:
-
-	i2c@00000000 {
-		/* ... */
-
-		touchscreen@48 {
-			compatible = "melfas,mms114";
-			reg = <0x48>;
-			interrupts = <39 0>;
-			touchscreen-size-x = <720>;
-			touchscreen-size-y = <1280>;
-			touchscreen-fuzz-x = <10>;
-			touchscreen-fuzz-y = <10>;
-			touchscreen-fuzz-pressure = <10>;
-			touchscreen-inverted-x;
-			touchscreen-inverted-y;
-		};
-
-		/* ... */
-	};
diff --git a/Documentation/devicetree/bindings/input/touchscreen/mstar,msg2638.yaml b/Documentation/devicetree/bindings/input/touchscreen/mstar,msg2638.yaml
new file mode 100644
index 000000000000..3a42c23faf6f
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/mstar,msg2638.yaml
@@ -0,0 +1,69 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/input/touchscreen/mstar,msg2638.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MStar msg2638 touchscreen controller Bindings
+
+maintainers:
+  - Vincent Knecht <vincent.knecht@mailoo.org>
+
+allOf:
+  - $ref: touchscreen.yaml#
+
+properties:
+  compatible:
+    const: mstar,msg2638
+
+  reg:
+    const: 0x26
+
+  interrupts:
+    maxItems: 1
+
+  reset-gpios:
+    maxItems: 1
+
+  vdd-supply:
+    description: Power supply regulator for the chip
+
+  vddio-supply:
+    description: Power supply regulator for the I2C bus
+
+  touchscreen-size-x: true
+  touchscreen-size-y: true
+
+additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - reset-gpios
+  - touchscreen-size-x
+  - touchscreen-size-y
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+      touchscreen@26 {
+        compatible = "mstar,msg2638";
+        reg = <0x26>;
+        interrupt-parent = <&msmgpio>;
+        interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
+        reset-gpios = <&msmgpio 100 GPIO_ACTIVE_LOW>;
+        pinctrl-names = "default";
+        pinctrl-0 = <&ts_int_reset_default>;
+        vdd-supply = <&pm8916_l17>;
+        vddio-supply = <&pm8916_l5>;
+        touchscreen-size-x = <2048>;
+        touchscreen-size-y = <2048>;
+      };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 99a72a480d32..b868cefc7c55 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -495,6 +495,8 @@ patternProperties:
     description: Shenzhen Hugsun Technology Co. Ltd.
   "^hwacom,.*":
     description: HwaCom Systems Inc.
+  "^hycon,.*":
+    description: Hycon Technology Corp.
   "^hydis,.*":
     description: Hydis Technologies
   "^hyundai,.*":