docs: hwmon: Add an index file and rename docs to *.rst

Now that all files were converted to ReST format, rename them
and add an index.

Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

1 files changed, 0 insertions, 124 deletions

diff --git a/Documentation/hwmon/w83627hf b/Documentation/hwmon/w83627hf
deleted file mode 100644
index d1406c28dee7..000000000000
--- a/Documentation/hwmon/w83627hf
+++ /dev/null
@@ -1,124 +0,0 @@
-Kernel driver w83627hf
-======================
-
-Supported chips:
-  * Winbond W83627HF (ISA accesses ONLY)
-    Prefix: 'w83627hf'
-    Addresses scanned: ISA address retrieved from Super I/O registers
-  * Winbond W83627THF
-    Prefix: 'w83627thf'
-    Addresses scanned: ISA address retrieved from Super I/O registers
-  * Winbond W83697HF
-    Prefix: 'w83697hf'
-    Addresses scanned: ISA address retrieved from Super I/O registers
-  * Winbond W83637HF
-    Prefix: 'w83637hf'
-    Addresses scanned: ISA address retrieved from Super I/O registers
-  * Winbond W83687THF
-    Prefix: 'w83687thf'
-    Addresses scanned: ISA address retrieved from Super I/O registers
-    Datasheet: Provided by Winbond on request(http://www.winbond.com/hq/enu)
-
-Authors:
-	Frodo Looijaard <frodol@dds.nl>,
-	Philip Edelbrock <phil@netroedge.com>,
-	Mark Studebaker <mdsxyz123@yahoo.com>,
-	Bernhard C. Schrenk <clemy@clemy.org>
-
-Module Parameters
------------------
-
-* force_i2c: int
-  Initialize the I2C address of the sensors
-* init: int
-  (default is 1)
-  Use 'init=0' to bypass initializing the chip.
-  Try this if your computer crashes when you load the module.
-
-Description
------------
-
-This driver implements support for ISA accesses *only* for
-the Winbond W83627HF, W83627THF, W83697HF and W83637HF Super I/O chips.
-We will refer to them collectively as Winbond chips.
-
-This driver supports ISA accesses, which should be more reliable
-than i2c accesses. Also, for Tyan boards which contain both a
-Super I/O chip and a second i2c-only Winbond chip (often a W83782D),
-using this driver will avoid i2c address conflicts and complex
-initialization that were required in the w83781d driver.
-
-If you really want i2c accesses for these Super I/O chips,
-use the w83781d driver. However this is not the preferred method
-now that this ISA driver has been developed.
-
-The `w83627_HF_` uses pins 110-106 as VID0-VID4. The `w83627_THF_` uses the
-same pins as GPIO[0:4]. Technically, the `w83627_THF_` does not support a
-VID reading. However the two chips have the identical 128 pin package. So,
-it is possible or even likely for a w83627thf to have the VID signals routed
-to these pins despite their not being labeled for that purpose. Therefore,
-the w83627thf driver interprets these as VID. If the VID on your board
-doesn't work, first see doc/vid in the lm_sensors package[1]. If that still
-doesn't help, you may just ignore the bogus VID reading with no harm done.
-
-For further information on this driver see the w83781d driver documentation.
-
-[1] http://www.lm-sensors.org/browser/lm-sensors/trunk/doc/vid
-
-Forcing the address
--------------------
-
-The driver used to have a module parameter named force_addr, which could
-be used to force the base I/O address of the hardware monitoring block.
-This was meant as a workaround for mainboards with a broken BIOS. This
-module parameter is gone for technical reasons. If you need this feature,
-you can obtain the same result by using the isaset tool (part of
-lm-sensors) before loading the driver:
-
-# Enter the Super I/O config space::
-
-	isaset -y -f 0x2e 0x87
-	isaset -y -f 0x2e 0x87
-
-# Select the hwmon logical device::
-
-	isaset -y 0x2e 0x2f 0x07 0x0b
-
-# Set the base I/O address (to 0x290 in this example)::
-
-	isaset -y 0x2e 0x2f 0x60 0x02
-	isaset -y 0x2e 0x2f 0x61 0x90
-
-# Exit the Super-I/O config space::
-
-	isaset -y -f 0x2e 0xaa
-
-The above sequence assumes a Super-I/O config space at 0x2e/0x2f, but
-0x4e/0x4f is also possible.
-
-Voltage pin mapping
--------------------
-
-Here is a summary of the voltage pin mapping for the W83627THF. This
-can be useful to convert data provided by board manufacturers into
-working libsensors configuration statements:
-
-
-- W83627THF
-
-
-  ======== =============== =============== ===============
-  Pin	   Name		   Register	   Sysfs attribute
-  ======== =============== =============== ===============
-    100	   CPUVCORE	   20h		   in0
-     99	   VIN0		   21h		   in1
-     98	   VIN1		   22h		   in2
-     97	   VIN2		   24h		   in4
-    114	   AVCC		   23h		   in3
-     61	   5VSB		   50h (bank 5)	   in7
-     74	   VBAT		   51h (bank 5)	   in8
-  ======== =============== =============== ===============
-
-For other supported devices, you'll have to take the hard path and
-look up the information in the datasheet yourself (and then add it
-to this document please.)