Merge git://linuxtv.org/sailus/media_tree into media_stage

* git://linuxtv.org/sailus/media_tree: (47 commits)
  media: i2c: ov4689: code cleanup
  media: ov9650: Drop platform data code path
  media: ov7670: Drop unused include
  media: ov2640: Drop legacy includes
  media: tc358746: add Toshiba TC358746 Parallel to CSI-2 bridge driver
  media: dt-bindings: add bindings for Toshiba TC358746
  phy: dphy: add support to calculate the timing based on hs_clk_rate
  phy: dphy: refactor get_default_config
  v4l: subdev: Warn if disabling streaming failed, return success
  dw9768: Enable low-power probe on ACPI
  media: i2c: imx290: Replace GAIN control with ANALOGUE_GAIN
  media: i2c: imx290: Add crop selection targets support
  media: i2c: imx290: Factor out format retrieval to separate function
  media: i2c: imx290: Move registers with fixed value to init array
  media: i2c: imx290: Create controls for fwnode properties
  media: i2c: imx290: Implement HBLANK and VBLANK controls
  media: i2c: imx290: Split control initialization to separate function
  media: i2c: imx290: Fix max gain value
  media: i2c: imx290: Add exposure time control
  media: i2c: imx290: Define more register macros
  ...

8 files changed, 622 insertions, 57 deletions

diff --git a/Documentation/devicetree/bindings/media/i2c/imx290.txt b/Documentation/devicetree/bindings/media/i2c/imx290.txt
deleted file mode 100644
index a3cc21410f7c..000000000000
--- a/Documentation/devicetree/bindings/media/i2c/imx290.txt
+++ /dev/null
@@ -1,57 +0,0 @@
-* Sony IMX290 1/2.8-Inch CMOS Image Sensor
-
-The Sony IMX290 is a 1/2.8-Inch CMOS Solid-state image sensor with
-Square Pixel for Color Cameras. It is programmable through I2C and 4-wire
-interfaces. The sensor output is available via CMOS logic parallel SDR output,
-Low voltage LVDS DDR output and CSI-2 serial data output. The CSI-2 bus is the
-default. No bindings have been defined for the other busses.
-
-Required Properties:
-- compatible: Should be "sony,imx290"
-- reg: I2C bus address of the device
-- clocks: Reference to the xclk clock.
-- clock-names: Should be "xclk".
-- clock-frequency: Frequency of the xclk clock in Hz.
-- vdddo-supply: Sensor digital IO regulator.
-- vdda-supply: Sensor analog regulator.
-- vddd-supply: Sensor digital core regulator.
-
-Optional Properties:
-- reset-gpios: Sensor reset GPIO
-
-The imx290 device node should contain one 'port' child node with
-an 'endpoint' subnode. For further reading on port node refer to
-Documentation/devicetree/bindings/media/video-interfaces.txt.
-
-Required Properties on endpoint:
-- data-lanes: check ../video-interfaces.txt
-- link-frequencies: check ../video-interfaces.txt
-- remote-endpoint: check ../video-interfaces.txt
-
-Example:
-	&i2c1 {
-		...
-		imx290: camera-sensor@1a {
-			compatible = "sony,imx290";
-			reg = <0x1a>;
-
-			reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&camera_rear_default>;
-
-			clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
-			clock-names = "xclk";
-			clock-frequency = <37125000>;
-
-			vdddo-supply = <&camera_vdddo_1v8>;
-			vdda-supply = <&camera_vdda_2v8>;
-			vddd-supply = <&camera_vddd_1v5>;
-
-			port {
-				imx290_ep: endpoint {
-					data-lanes = <1 2 3 4>;
-					link-frequencies = /bits/ 64 <445500000>;
-					remote-endpoint = <&csiphy0_ep>;
-				};
-			};
-		};
diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov4689.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov4689.yaml
new file mode 100644
index 000000000000..50579c947f3c
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov4689.yaml
@@ -0,0 +1,134 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/ovti,ov4689.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Omnivision OV4689 CMOS
+
+maintainers:
+  - Mikhail Rudenko <mike.rudenko@gmail.com>
+
+description: |
+  The Omnivision OV4689 is a high performance, 1/3-inch, 4 megapixel
+  image sensor. Ihis chip supports high frame rate speeds up to 90 fps
+  at 2688x1520 resolution. It is programmable through an I2C
+  interface, and sensor output is sent via 1/2/4 lane MIPI CSI-2
+  connection.
+
+allOf:
+  - $ref: /schemas/media/video-interface-devices.yaml#
+
+properties:
+  compatible:
+    const: ovti,ov4689
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    description:
+      External clock (XVCLK) for the sensor, 6-64 MHz
+    maxItems: 1
+
+  dovdd-supply:
+    description:
+      Digital I/O voltage supply, 1.7-3.0 V
+
+  avdd-supply:
+    description:
+      Analog voltage supply, 2.6-3.0 V
+
+  dvdd-supply:
+    description:
+      Digital core voltage supply, 1.1-1.3 V
+
+  powerdown-gpios:
+    description:
+      GPIO connected to the powerdown pin (active low)
+
+  reset-gpios:
+    maxItems: 1
+    description:
+      GPIO connected to the reset pin (active low)
+
+  orientation: true
+
+  rotation: true
+
+  port:
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    additionalProperties: false
+    description:
+      Output port node, single endpoint describing the CSI-2 transmitter
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          data-lanes:
+            oneOf:
+              - items:
+                  - const: 1
+                  - const: 2
+                  - const: 3
+                  - const: 4
+              - items:
+                  - const: 1
+                  - const: 2
+              - items:
+                  - const: 1
+          link-frequencies: true
+
+        required:
+          - data-lanes
+          - link-frequencies
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - dovdd-supply
+  - avdd-supply
+  - dvdd-supply
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ov4689: camera@36 {
+            compatible = "ovti,ov4689";
+            reg = <0x36>;
+
+            clocks = <&ov4689_clk>;
+
+            avdd-supply = <&ov4689_avdd>;
+            dovdd-supply = <&ov4689_dovdd>;
+            dvdd-supply = <&ov4689_dvdd>;
+
+            powerdown-gpios = <&pio 107 GPIO_ACTIVE_LOW>;
+            reset-gpios = <&pio 109 GPIO_ACTIVE_LOW>;
+
+            orientation = <2>;
+            rotation = <0>;
+
+            port {
+                wcam_out: endpoint {
+                    remote-endpoint = <&mipi_in_wcam>;
+                    data-lanes = <1 2 3 4>;
+                    link-frequencies = /bits/ 64 <504000000>;
+                };
+            };
+        };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx290.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx290.yaml
new file mode 100644
index 000000000000..21377daae026
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/sony,imx290.yaml
@@ -0,0 +1,129 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/sony,imx290.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Sony IMX290 1/2.8-Inch CMOS Image Sensor
+
+maintainers:
+  - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+  - Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+
+description: |-
+  The Sony IMX290 is a 1/2.8-Inch CMOS Solid-state image sensor with Square
+  Pixel for Color Cameras. It is programmable through I2C and 4-wire
+  interfaces. The sensor output is available via CMOS logic parallel SDR
+  output, Low voltage LVDS DDR output and CSI-2 serial data output. The CSI-2
+  bus is the default. No bindings have been defined for the other busses.
+
+properties:
+  compatible:
+    enum:
+      - sony,imx290
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    description: Input clock (37.125 MHz or 74.25 MHz)
+    items:
+      - const: xclk
+
+  clock-frequency:
+    description: Frequency of the xclk clock in Hz
+
+  vdda-supply:
+    description: Analog power supply (2.9V)
+
+  vddd-supply:
+    description: Digital core power supply (1.2V)
+
+  vdddo-supply:
+    description: Digital I/O power supply (1.8V)
+
+  reset-gpios:
+    description: Sensor reset (XCLR) GPIO
+    maxItems: 1
+
+  port:
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    description: |
+      Video output port
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          data-lanes:
+            anyOf:
+              - items:
+                  - const: 1
+                  - const: 2
+              - items:
+                  - const: 1
+                  - const: 2
+                  - const: 3
+                  - const: 4
+
+          link-frequencies: true
+
+        required:
+          - data-lanes
+          - link-frequencies
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - clock-frequency
+  - vdda-supply
+  - vddd-supply
+  - vdddo-supply
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        imx290: camera-sensor@1a {
+            compatible = "sony,imx290";
+            reg = <0x1a>;
+
+            pinctrl-names = "default";
+            pinctrl-0 = <&camera_rear_default>;
+
+            clocks = <&gcc 90>;
+            clock-names = "xclk";
+            clock-frequency = <37125000>;
+
+            vdddo-supply = <&camera_vdddo_1v8>;
+            vdda-supply = <&camera_vdda_2v8>;
+            vddd-supply = <&camera_vddd_1v5>;
+
+            reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>;
+
+            port {
+                imx290_ep: endpoint {
+                    data-lanes = <1 2 3 4>;
+                    link-frequencies = /bits/ 64 <445500000>;
+                    remote-endpoint = <&csiphy0_ep>;
+                };
+            };
+        };
+    };
+...
diff --git a/Documentation/devicetree/bindings/media/i2c/st,st-vgxy61.yaml b/Documentation/devicetree/bindings/media/i2c/st,st-vgxy61.yaml
new file mode 100644
index 000000000000..6597e1d0e65f
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/st,st-vgxy61.yaml
@@ -0,0 +1,113 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+# Copyright (c) 2022 STMicroelectronics SA.
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/st,st-vgxy61.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectronics VGxy61 HDR Global Shutter Sensor Family Device Tree Bindings
+
+maintainers:
+  - Benjamin Mugnier <benjamin.mugnier@foss.st.com>
+  - Sylvain Petinot <sylvain.petinot@foss.st.com>
+
+description: |-
+  STMicroelectronics VGxy61 family has a CSI-2 output port. CSI-2 output is a
+  quad lanes 800Mbps per lane.
+  Supported formats are RAW8, RAW10, RAW12, RAW14 and RAW16.
+  Following part number are supported
+  - VG5661 and VG6661 are 1.6 Mpx (1464 x 1104) monochrome and color sensors.
+  Maximum frame rate is 75 fps.
+  - VG5761 and VG6761 are 2.3 Mpx (1944 x 1204) monochrome and color sensors.
+  Maximum frame rate is 60 fps.
+
+properties:
+  compatible:
+    const: st,st-vgxy61
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  VCORE-supply:
+    description:
+      Sensor digital core supply. Must be 1.2 volts.
+
+  VDDIO-supply:
+    description:
+      Sensor digital IO supply. Must be 1.8 volts.
+
+  VANA-supply:
+    description:
+      Sensor analog supply. Must be 2.8 volts.
+
+  reset-gpios:
+    description:
+      Reference to the GPIO connected to the reset pin, if any.
+      This is an active low signal to the vgxy61.
+
+  st,strobe-gpios-polarity:
+    description:
+      Invert polarity of illuminator's lights strobe GPIOs.
+      These GPIOs directly drive the illuminator LEDs.
+    type: boolean
+
+  port:
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    additionalProperties: false
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          data-lanes:
+            description:
+              CSI lanes to use
+            items:
+              - const: 1
+              - const: 2
+              - const: 3
+              - const: 4
+
+          remote-endpoint: true
+
+        required:
+          - data-lanes
+
+required:
+  - compatible
+  - clocks
+  - VCORE-supply
+  - VDDIO-supply
+  - VANA-supply
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        vgxy61: csi2tx@10 {
+            compatible = "st,st-vgxy61";
+            reg = <0x10>;
+            clocks = <&clk_ext_camera>;
+            VCORE-supply = <&v1v2>;
+            VDDIO-supply = <&v1v8>;
+            VANA-supply = <&v2v8>;
+            reset-gpios = <&mfxgpio 18 GPIO_ACTIVE_LOW>;
+            port {
+                ep0: endpoint {
+                    data-lanes = <1 2 3 4>;
+                    remote-endpoint = <&mipi_csi2_out>;
+                };
+            };
+        };
+    };
+...
diff --git a/Documentation/devicetree/bindings/media/i2c/toshiba,tc358746.yaml b/Documentation/devicetree/bindings/media/i2c/toshiba,tc358746.yaml
new file mode 100644
index 000000000000..b8ba85a2416c
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/toshiba,tc358746.yaml
@@ -0,0 +1,178 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/toshiba,tc358746.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Toshiba TC358746 Parallel to MIPI CSI2 Bridge
+
+maintainers:
+  - Marco Felsch <kernel@pengutronix.de>
+
+description: |-
+  The Toshiba TC358746 converts a parallel video stream into a MIPI CSI-2
+  stream. The direction can be either parallel-in -> csi-out or csi-in ->
+  parallel-out The chip is programmable trough I2C and SPI but the SPI
+  interface is only supported in parallel-in -> csi-out mode.
+
+  Note that the current device tree bindings only support the
+  parallel-in -> csi-out path.
+
+properties:
+  compatible:
+    const: toshiba,tc358746
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    description:
+      The phandle to the reference clock source. This corresponds to the
+      hardware pin REFCLK.
+    maxItems: 1
+
+  clock-names:
+    const: refclk
+
+  "#clock-cells":
+    description: |
+      The bridge can act as clock provider for the sensor. To enable this
+      support #clock-cells must be specified. Attention if this feature is used
+      then the mclk rate must be at least: (2 * link-frequency) / 8
+                                           `------------------´   ^
+                                           internal PLL rate   smallest possible
+                                                                   mclk-div
+    const: 0
+
+  clock-output-names:
+    description:
+      The clock name of the MCLK output, the default name is tc358746-mclk.
+    maxItems: 1
+
+  vddc-supply:
+    description: Digital core voltage supply, 1.2 volts
+
+  vddio-supply:
+    description: Digital I/O voltage supply, 1.8 volts
+
+  vddmipi-supply:
+    description: MIPI CSI phy voltage supply, 1.2 volts
+
+  reset-gpios:
+    description:
+      The phandle and specifier for the GPIO that controls the chip reset.
+      This corresponds to the hardware pin RESX which is physically active low.
+    maxItems: 1
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        description: Input port
+
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              hsync-active: true
+              vsync-active: true
+              bus-type:
+                enum: [ 5, 6 ]
+
+            required:
+              - hsync-active
+              - vsync-active
+              - bus-type
+
+      port@1:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        description: Output port
+
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              data-lanes:
+                minItems: 1
+                maxItems: 4
+
+              clock-noncontinuous: true
+              link-frequencies: true
+
+            required:
+              - data-lanes
+              - link-frequencies
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - vddc-supply
+  - vddio-supply
+  - vddmipi-supply
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      csi-bridge@e {
+        compatible = "toshiba,tc358746";
+        reg = <0xe>;
+
+        clocks = <&refclk>;
+        clock-names = "refclk";
+
+        reset-gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+
+        vddc-supply = <&v1_2d>;
+        vddio-supply = <&v1_8d>;
+        vddmipi-supply = <&v1_2d>;
+
+        /* sensor mclk provider */
+        #clock-cells = <0>;
+
+        ports {
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          /* Input */
+          port@0 {
+            reg = <0>;
+            tc358746_in: endpoint {
+              remote-endpoint = <&sensor_out>;
+              hsync-active = <0>;
+              vsync-active = <0>;
+              bus-type = <5>;
+            };
+          };
+
+          /* Output */
+          port@1 {
+            reg = <1>;
+            tc358746_out: endpoint {
+              remote-endpoint = <&mipi_csi2_in>;
+              data-lanes = <1 2>;
+              clock-noncontinuous;
+              link-frequencies = /bits/ 64 <216000000>;
+            };
+          };
+        };
+      };
+    };
diff --git a/Documentation/userspace-api/media/drivers/st-vgxy61.rst b/Documentation/userspace-api/media/drivers/st-vgxy61.rst
new file mode 100644
index 000000000000..213b884dcfa6
--- /dev/null
+++ b/Documentation/userspace-api/media/drivers/st-vgxy61.rst
@@ -0,0 +1,23 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+ST VGXY61 camera sensor driver
+==============================
+
+The ST VGXY61 driver implements the following controls:
+
+``V4L2_CID_HDR_SENSOR_MODE``
+-------------------------------
+    Change the sensor HDR mode. A HDR picture is obtained by merging two captures of the same scene
+    using two different exposure periods.
+
+.. flat-table::
+    :header-rows:  0
+    :stub-columns: 0
+    :widths:       1 4
+
+    * - HDR linearize
+      - The merger outputs a long exposure capture as long as it is not saturated.
+    * - HDR substraction
+      - This involves subtracting the short exposure frame from the long exposure frame.
+    * - "No HDR"
+      - This mode is used for standard dynamic range (SDR) exposures.
diff --git a/Documentation/userspace-api/media/v4l/ext-ctrls-camera.rst b/Documentation/userspace-api/media/v4l/ext-ctrls-camera.rst
index 4c5061aa9cd4..daa4f40869f8 100644
--- a/Documentation/userspace-api/media/v4l/ext-ctrls-camera.rst
+++ b/Documentation/userspace-api/media/v4l/ext-ctrls-camera.rst
@@ -661,3 +661,11 @@ enum v4l2_scene_mode -
 .. [#f1]
    This control may be changed to a menu control in the future, if more
    options are required.
+
+``V4L2_CID_HDR_SENSOR_MODE (menu)``
+    Change the sensor HDR mode. A HDR picture is obtained by merging two
+    captures of the same scene using two different exposure periods. HDR mode
+    describes the way these two captures are merged in the sensor.
+
+    As modes differ for each sensor, menu items are not standardized by this
+    control and are left to the programmer.
diff --git a/Documentation/userspace-api/media/v4l/subdev-formats.rst b/Documentation/userspace-api/media/v4l/subdev-formats.rst
index d21d532eee15..16ef3b41932e 100644
--- a/Documentation/userspace-api/media/v4l/subdev-formats.rst
+++ b/Documentation/userspace-api/media/v4l/subdev-formats.rst
@@ -6057,6 +6057,43 @@ the following codes.
       - y\ :sub:`2`
       - y\ :sub:`1`
       - y\ :sub:`0`
+    * .. _MEDIA-BUS-FMT-Y16-1X16:
+
+      - MEDIA_BUS_FMT_Y16_1X16
+      - 0x202e
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      - y\ :sub:`15`
+      - y\ :sub:`14`
+      - y\ :sub:`13`
+      - y\ :sub:`12`
+      - y\ :sub:`11`
+      - y\ :sub:`10`
+      - y\ :sub:`9`
+      - y\ :sub:`8`
+      - y\ :sub:`7`
+      - y\ :sub:`6`
+      - y\ :sub:`5`
+      - y\ :sub:`4`
+      - y\ :sub:`3`
+      - y\ :sub:`2`
+      - y\ :sub:`1`
+      - y\ :sub:`0`
     * .. _MEDIA-BUS-FMT-UYVY8-1X16:
 
       - MEDIA_BUS_FMT_UYVY8_1X16