Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC driver updates from Arnd Bergmann:
 "This contains driver changes that are tightly connected to SoC
  specific code. Aside from smaller cleanups and bug fixes, here is a
  list of the notable changes.

  New device drivers:

   - The Turris Mox router has a new "moxtet" bus driver for its
     on-board pluggable extension bus. The same platform also gains a
     firmware driver.

   - The Samsung Exynos family gains a new Chipid driver exporting using
     the soc device sysfs interface

   - A similar socinfo driver for Qualcomm Snapdragon chips.

   - A firmware driver for the NXP i.MX DSP IPC protocol using shared
     memory and a mailbox

  Other changes:

   - The i.MX reset controller driver now supports the NXP i.MX8MM chip

   - Amlogic SoC specific drivers gain support for the S905X3 and A311D
     chips

   - A rework of the TI Davinci framebuffer driver to allow important
     cleanups in the platform code

   - A couple of device drivers for removed ARM SoC platforms are
     removed. Most of the removals were picked up by other maintainers,
     this contains whatever was left"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
  bus: uniphier-system-bus: use devm_platform_ioremap_resource()
  soc: ti: ti_sci_pm_domains: Add support for exclusive and shared access
  dt-bindings: ti_sci_pm_domains: Add support for exclusive and shared access
  firmware: ti_sci: Allow for device shared and exclusive requests
  bus: imx-weim: remove incorrect __init annotations
  fbdev: remove w90x900/nuc900 platform drivers
  spi: remove w90x900 driver
  net: remove w90p910-ether driver
  net: remove ks8695 driver
  firmware: turris-mox-rwtm: Add sysfs documentation
  firmware: Add Turris Mox rWTM firmware driver
  dt-bindings: firmware: Document cznic,turris-mox-rwtm binding
  bus: moxtet: fix unsigned comparison to less than zero
  bus: moxtet: remove set but not used variable 'dummy'
  ARM: scoop: Use the right include
  dt-bindings: power: add Amlogic Everything-Else power domains bindings
  soc: amlogic: Add support for Everything-Else power domains controller
  fbdev: da8xx: use resource management for dma
  fbdev: da8xx-fb: drop a redundant if
  fbdev: da8xx-fb: use devm_platform_ioremap_resource()
  ...

16 files changed, 340 insertions, 7 deletions

diff --git a/Documentation/ABI/testing/debugfs-moxtet b/Documentation/ABI/testing/debugfs-moxtet
new file mode 100644
index 000000000000..67b1717794d8
--- /dev/null
+++ b/Documentation/ABI/testing/debugfs-moxtet
@@ -0,0 +1,23 @@
+What:		/sys/kernel/debug/moxtet/input
+Date:		March 2019
+KernelVersion:	5.3
+Contact:	Marek Behún <marek.behun@nic.cz>
+Description:	(R) Read input from the shift registers, in hexadecimal.
+		Returns N+1 bytes, where N is the number of Moxtet connected
+		modules. The first byte is from the CPU board itself.
+		Example: 101214
+			 10: CPU board with SD card
+			 12: 2 = PCIe module, 1 = IRQ not active
+			 14: 4 = Peridot module, 1 = IRQ not active
+
+What:		/sys/kernel/debug/moxtet/output
+Date:		March 2019
+KernelVersion:	5.3
+Contact:	Marek Behún <marek.behun@nic.cz>
+Description:	(RW) Read last written value to the shift registers, in
+		hexadecimal, or write values to the shift registers, also
+		in hexadecimal.
+		Example: 0102
+			 01: 01 was last written, or is to be written, to the
+			     first module's shift register
+			 02: the same for second module
diff --git a/Documentation/ABI/testing/sysfs-bus-moxtet-devices b/Documentation/ABI/testing/sysfs-bus-moxtet-devices
new file mode 100644
index 000000000000..355958527fa3
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-moxtet-devices
@@ -0,0 +1,17 @@
+What:		/sys/bus/moxtet/devices/moxtet-<name>.<addr>/module_description
+Date:		March 2019
+KernelVersion:	5.3
+Contact:	Marek Behún <marek.behun@nic.cz>
+Description:	(R) Moxtet module description. Format: string
+
+What:		/sys/bus/moxtet/devices/moxtet-<name>.<addr>/module_id
+Date:		March 2019
+KernelVersion:	5.3
+Contact:	Marek Behún <marek.behun@nic.cz>
+Description:	(R) Moxtet module ID. Format: %x
+
+What:		/sys/bus/moxtet/devices/moxtet-<name>.<addr>/module_name
+Date:		March 2019
+KernelVersion:	5.3
+Contact:	Marek Behún <marek.behun@nic.cz>
+Description:	(R) Moxtet module name. Format: string
diff --git a/Documentation/ABI/testing/sysfs-devices-soc b/Documentation/ABI/testing/sysfs-devices-soc
index 6d9cc253f2b2..ba3a3fac0ee1 100644
--- a/Documentation/ABI/testing/sysfs-devices-soc
+++ b/Documentation/ABI/testing/sysfs-devices-soc
@@ -26,6 +26,13 @@ Description:
 		Read-only attribute common to all SoCs. Contains SoC family name
 		(e.g. DB8500).
 
+What:		/sys/devices/socX/serial_number
+Date:		January 2019
+contact:	Bjorn Andersson <bjorn.andersson@linaro.org>
+Description:
+		Read-only attribute supported by most SoCs. Contains the SoC's
+		serial number, if available.
+
 What:		/sys/devices/socX/soc_id
 Date:		January 2012
 contact:	Lee Jones <lee.jones@linaro.org>
diff --git a/Documentation/ABI/testing/sysfs-firmware-turris-mox-rwtm b/Documentation/ABI/testing/sysfs-firmware-turris-mox-rwtm
new file mode 100644
index 000000000000..15595fab88d1
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-firmware-turris-mox-rwtm
@@ -0,0 +1,37 @@
+What:		/sys/firmware/turris-mox-rwtm/board_version
+Date:		August 2019
+KernelVersion:	5.4
+Contact:	Marek Behún <marek.behun@nic.cz>
+Description:	(R) Board version burned into eFuses of this Turris Mox board.
+		Format: %i
+
+What:		/sys/firmware/turris-mox-rwtm/mac_address*
+Date:		August 2019
+KernelVersion:	5.4
+Contact:	Marek Behún <marek.behun@nic.cz>
+Description:	(R) MAC addresses burned into eFuses of this Turris Mox board.
+		Format: %pM
+
+What:		/sys/firmware/turris-mox-rwtm/pubkey
+Date:		August 2019
+KernelVersion:	5.4
+Contact:	Marek Behún <marek.behun@nic.cz>
+Description:	(R) ECDSA public key (in pubkey hex compressed form) computed
+		as pair to the ECDSA private key burned into eFuses of this
+		Turris Mox Board.
+		Format: string
+
+What:		/sys/firmware/turris-mox-rwtm/ram_size
+Date:		August 2019
+KernelVersion:	5.4
+Contact:	Marek Behún <marek.behun@nic.cz>
+Description:	(R) RAM size in MiB of this Turris Mox board as was detected
+		during manufacturing and burned into eFuses. Can be 512 or 1024.
+		Format: %i
+
+What:		/sys/firmware/turris-mox-rwtm/serial_number
+Date:		August 2019
+KernelVersion:	5.4
+Contact:	Marek Behún <marek.behun@nic.cz>
+Description:	(R) Serial number burned into eFuses of this Turris Mox device.
+		Format: %016X
diff --git a/Documentation/devicetree/bindings/arm/arm,scmi.txt b/Documentation/devicetree/bindings/arm/arm,scmi.txt
index 317a2fc3667a..083dbf96ee00 100644
--- a/Documentation/devicetree/bindings/arm/arm,scmi.txt
+++ b/Documentation/devicetree/bindings/arm/arm,scmi.txt
@@ -73,6 +73,16 @@ Required properties:
 			 as used by the firmware. Refer to  platform details
 			 for your implementation for the IDs to use.
 
+Reset signal bindings for the reset domains based on SCMI Message Protocol
+------------------------------------------------------------
+
+This binding for the SCMI reset domain providers uses the generic reset
+signal binding[5].
+
+Required properties:
+ - #reset-cells : Should be 1. Contains the reset domain ID value used
+		  by SCMI commands.
+
 SRAM and Shared Memory for SCMI
 -------------------------------
 
@@ -93,6 +103,7 @@ Required sub-node properties:
 [2] Documentation/devicetree/bindings/power/power_domain.txt
 [3] Documentation/devicetree/bindings/thermal/thermal.txt
 [4] Documentation/devicetree/bindings/sram/sram.txt
+[5] Documentation/devicetree/bindings/reset/reset.txt
 
 Example:
 
@@ -152,6 +163,11 @@ firmware {
 			reg = <0x15>;
 			#thermal-sensor-cells = <1>;
 		};
+
+		scmi_reset: protocol@16 {
+			reg = <0x16>;
+			#reset-cells = <1>;
+		};
 	};
 };
 
@@ -166,6 +182,7 @@ hdlcd@7ff60000 {
 	reg = <0 0x7ff60000 0 0x1000>;
 	clocks = <&scmi_clk 4>;
 	power-domains = <&scmi_devpd 1>;
+	resets = <&scmi_reset 10>;
 };
 
 thermal-zones {
diff --git a/Documentation/devicetree/bindings/bus/moxtet.txt b/Documentation/devicetree/bindings/bus/moxtet.txt
new file mode 100644
index 000000000000..fb50fc865336
--- /dev/null
+++ b/Documentation/devicetree/bindings/bus/moxtet.txt
@@ -0,0 +1,46 @@
+Turris Mox module status and configuration bus (over SPI)
+
+Required properties:
+ - compatible		: Should be "cznic,moxtet"
+ - #address-cells	: Has to be 1
+ - #size-cells		: Has to be 0
+ - spi-cpol		: Required inverted clock polarity
+ - spi-cpha		: Required shifted clock phase
+ - interrupts		: Must contain reference to the shared interrupt line
+ - interrupt-controller	: Required
+ - #interrupt-cells	: Has to be 1
+
+For other required and optional properties of SPI slave nodes please refer to
+../spi/spi-bus.txt.
+
+Required properties of subnodes:
+ - reg			: Should be position on the Moxtet bus (how many Moxtet
+			  modules are between this module and CPU module, so
+			  either 0 or a positive integer)
+
+The driver finds the devices connected to the bus by itself, but it may be
+needed to reference some of them from other parts of the device tree. In that
+case the devices can be defined as subnodes of the moxtet node.
+
+Example:
+
+	moxtet@1 {
+		compatible = "cznic,moxtet";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <1>;
+		spi-max-frequency = <10000000>;
+		spi-cpol;
+		spi-cpha;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		interrupt-parent = <&gpiosb>;
+		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+
+		moxtet_sfp: gpio@0 {
+			compatible = "cznic,moxtet-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+			reg = <0>;
+		}
+	};
diff --git a/Documentation/devicetree/bindings/firmware/cznic,turris-mox-rwtm.txt b/Documentation/devicetree/bindings/firmware/cznic,turris-mox-rwtm.txt
new file mode 100644
index 000000000000..338169dea7bb
--- /dev/null
+++ b/Documentation/devicetree/bindings/firmware/cznic,turris-mox-rwtm.txt
@@ -0,0 +1,19 @@
+Turris Mox rWTM firmware driver
+
+Required properties:
+ - compatible		: Should be "cznic,turris-mox-rwtm"
+ - mboxes		: Must contain a reference to associated mailbox
+
+This device tree node should be used on Turris Mox, or potentially another A3700
+compatible device running the Mox's rWTM firmware in the secure processor (for
+example it is possible to flash this firmware into EspressoBin).
+
+Example:
+
+	firmware {
+		turris-mox-rwtm {
+			compatible = "cznic,turris-mox-rwtm";
+			mboxes = <&rwtm 0>;
+			status = "okay";
+		};
+	};
diff --git a/Documentation/devicetree/bindings/firmware/qcom,scm.txt b/Documentation/devicetree/bindings/firmware/qcom,scm.txt
index 41f133a4e2fa..3f29ea04b5fe 100644
--- a/Documentation/devicetree/bindings/firmware/qcom,scm.txt
+++ b/Documentation/devicetree/bindings/firmware/qcom,scm.txt
@@ -9,14 +9,16 @@ Required properties:
 - compatible: must contain one of the following:
  * "qcom,scm-apq8064"
  * "qcom,scm-apq8084"
+ * "qcom,scm-ipq4019"
  * "qcom,scm-msm8660"
  * "qcom,scm-msm8916"
  * "qcom,scm-msm8960"
  * "qcom,scm-msm8974"
  * "qcom,scm-msm8996"
  * "qcom,scm-msm8998"
- * "qcom,scm-ipq4019"
+ * "qcom,scm-sc7180"
  * "qcom,scm-sdm845"
+ * "qcom,scm-sm8150"
  and:
  * "qcom,scm"
 - clocks: Specifies clocks needed by the SCM interface, if any:
diff --git a/Documentation/devicetree/bindings/gpio/gpio-moxtet.txt b/Documentation/devicetree/bindings/gpio/gpio-moxtet.txt
new file mode 100644
index 000000000000..410759de9f09
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-moxtet.txt
@@ -0,0 +1,18 @@
+Turris Mox Moxtet GPIO expander via Moxtet bus
+
+Required properties:
+ - compatible		: Should be "cznic,moxtet-gpio".
+ - gpio-controller	: Marks the device node as a GPIO controller.
+ - #gpio-cells		: Should be two. For consumer use see gpio.txt.
+
+Other properties are required for a Moxtet bus device, please refer to
+Documentation/devicetree/bindings/bus/moxtet.txt.
+
+Example:
+
+	moxtet_sfp: gpio@0 {
+		compatible = "cznic,moxtet-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		reg = <0>;
+	}
diff --git a/Documentation/devicetree/bindings/power/amlogic,meson-ee-pwrc.yaml b/Documentation/devicetree/bindings/power/amlogic,meson-ee-pwrc.yaml
new file mode 100644
index 000000000000..aab70e8b681e
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/amlogic,meson-ee-pwrc.yaml
@@ -0,0 +1,93 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+# Copyright 2019 BayLibre, SAS
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/power/amlogic,meson-ee-pwrc.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Amlogic Meson Everything-Else Power Domains
+
+maintainers:
+  - Neil Armstrong <narmstrong@baylibre.com>
+
+description: |+
+  The Everything-Else Power Domains node should be the child of a syscon
+  node with the required property:
+
+  - compatible: Should be the following:
+                "amlogic,meson-gx-hhi-sysctrl", "simple-mfd", "syscon"
+
+  Refer to the the bindings described in
+  Documentation/devicetree/bindings/mfd/syscon.txt
+
+properties:
+  compatible:
+    enum:
+      - amlogic,meson-g12a-pwrc
+      - amlogic,meson-sm1-pwrc
+
+  clocks:
+    minItems: 2
+
+  clock-names:
+    items:
+      - const: vpu
+      - const: vapb
+
+  resets:
+    minItems: 11
+
+  reset-names:
+    items:
+      - const: viu
+      - const: venc
+      - const: vcbus
+      - const: bt656
+      - const: rdma
+      - const: venci
+      - const: vencp
+      - const: vdac
+      - const: vdi6
+      - const: vencl
+      - const: vid_lock
+
+  "#power-domain-cells":
+    const: 1
+
+  amlogic,ao-sysctrl:
+    description: phandle to the AO sysctrl node
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/phandle
+
+required:
+  - compatible
+  - clocks
+  - clock-names
+  - resets
+  - reset-names
+  - "#power-domain-cells"
+  - amlogic,ao-sysctrl
+
+examples:
+  - |
+    pwrc: power-controller {
+          compatible = "amlogic,meson-sm1-pwrc";
+          #power-domain-cells = <1>;
+          amlogic,ao-sysctrl = <&rti>;
+          resets = <&reset_viu>,
+                   <&reset_venc>,
+                   <&reset_vcbus>,
+                   <&reset_bt656>,
+                   <&reset_rdma>,
+                   <&reset_venci>,
+                   <&reset_vencp>,
+                   <&reset_vdac>,
+                   <&reset_vdi6>,
+                   <&reset_vencl>,
+                   <&reset_vid_lock>;
+          reset-names = "viu", "venc", "vcbus", "bt656",
+                        "rdma", "venci", "vencp", "vdac",
+                        "vdi6", "vencl", "vid_lock";
+          clocks = <&clk_vpu>, <&clk_vapb>;
+          clock-names = "vpu", "vapb";
+    };
diff --git a/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt b/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
index 13e095182db4..c2489e41a801 100644
--- a/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
+++ b/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
@@ -8,6 +8,7 @@ Required properties:
 - compatible:
 	- For i.MX7 SoCs should be "fsl,imx7d-src", "syscon"
 	- For i.MX8MQ SoCs should be "fsl,imx8mq-src", "syscon"
+	- For i.MX8MM SoCs should be "fsl,imx8mm-src", "fsl,imx8mq-src", "syscon"
 - reg: should be register base and length as documented in the
   datasheet
 - interrupts: Should contain SRC interrupt
@@ -46,5 +47,6 @@ Example:
 
 
 For list of all valid reset indices see
-<dt-bindings/reset/imx7-reset.h> for i.MX7 and
-<dt-bindings/reset/imx8mq-reset.h> for i.MX8MQ
+<dt-bindings/reset/imx7-reset.h> for i.MX7,
+<dt-bindings/reset/imx8mq-reset.h> for i.MX8MQ and
+<dt-bindings/reset/imx8mq-reset.h> for i.MX8MM
diff --git a/Documentation/devicetree/bindings/reset/snps,dw-reset.txt b/Documentation/devicetree/bindings/reset/snps,dw-reset.txt
new file mode 100644
index 000000000000..f94f911dd98d
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/snps,dw-reset.txt
@@ -0,0 +1,30 @@
+Synopsys DesignWare Reset controller
+=======================================
+
+Please also refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Required properties:
+
+- compatible: should be one of the following.
+	"snps,dw-high-reset" - for active high configuration
+	"snps,dw-low-reset" - for active low configuration
+
+- reg: physical base address of the controller and length of memory mapped
+	region.
+
+- #reset-cells: must be 1.
+
+example:
+
+	dw_rst_1: reset-controller@0000 {
+		compatible = "snps,dw-high-reset";
+		reg = <0x0000 0x4>;
+		#reset-cells = <1>;
+	};
+
+	dw_rst_2: reset-controller@1000 {i
+		compatible = "snps,dw-low-reset";
+		reg = <0x1000 0x8>;
+		#reset-cells = <1>;
+	};
diff --git a/Documentation/devicetree/bindings/soc/amlogic/clk-measure.txt b/Documentation/devicetree/bindings/soc/amlogic/clk-measure.txt
index 6bf6b43f8dd8..3dd563cec794 100644
--- a/Documentation/devicetree/bindings/soc/amlogic/clk-measure.txt
+++ b/Documentation/devicetree/bindings/soc/amlogic/clk-measure.txt
@@ -11,6 +11,7 @@ Required properties:
 			"amlogic,meson8b-clk-measure" for Meson8b SoCs
 			"amlogic,meson-axg-clk-measure" for AXG SoCs
 			"amlogic,meson-g12a-clk-measure" for G12a SoCs
+			"amlogic,meson-sm1-clk-measure" for SM1 SoCs
 - reg: base address and size of the Clock Measurer register space.
 
 Example:
diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe.txt
index d7afaff5faff..05ec2a838c54 100644
--- a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe.txt
+++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe.txt
@@ -18,7 +18,8 @@ Required properties:
 - reg : offset and length of the device registers.
 - bus-frequency : the clock frequency for QUICC Engine.
 - fsl,qe-num-riscs: define how many RISC engines the QE has.
-- fsl,qe-num-snums: define how many serial number(SNUM) the QE can use for the
+- fsl,qe-snums: This property has to be specified as '/bits/ 8' value,
+  defining the array of serial number (SNUM) values for the virtual
   threads.
 
 Optional properties:
@@ -34,6 +35,11 @@ Recommended properties
 - brg-frequency : the internal clock source frequency for baud-rate
   generators in Hz.
 
+Deprecated properties
+- fsl,qe-num-snums: define how many serial number(SNUM) the QE can use
+  for the threads. Use fsl,qe-snums instead to not only specify the
+  number of snums, but also their values.
+
 Example:
      qe@e0100000 {
 	#address-cells = <1>;
@@ -44,6 +50,11 @@ Example:
 	reg = <e0100000 480>;
 	brg-frequency = <0>;
 	bus-frequency = <179A7B00>;
+	fsl,qe-snums = /bits/ 8 <
+		0x04 0x05 0x0C 0x0D 0x14 0x15 0x1C 0x1D
+		0x24 0x25 0x2C 0x2D 0x34 0x35 0x88 0x89
+		0x98 0x99 0xA8 0xA9 0xB8 0xB9 0xC8 0xC9
+		0xD8 0xD9 0xE8 0xE9>;
      }
 
 * Multi-User RAM (MURAM)
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,aoss-qmp.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,aoss-qmp.txt
index 954ffee0a9c4..4fc571e78f01 100644
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,aoss-qmp.txt
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,aoss-qmp.txt
@@ -15,7 +15,10 @@ power-domains.
 - compatible:
 	Usage: required
 	Value type: <string>
-	Definition: must be "qcom,sdm845-aoss-qmp"
+	Definition: must be one of:
+		    "qcom,sc7180-aoss-qmp"
+		    "qcom,sdm845-aoss-qmp"
+		    "qcom,sm8150-aoss-qmp"
 
 - reg:
 	Usage: required
diff --git a/Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt b/Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt
index f7b00a7c0f68..f541d1f776a2 100644
--- a/Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt
+++ b/Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt
@@ -19,8 +19,15 @@ child of the pmmc node.
 Required Properties:
 --------------------
 - compatible: should be "ti,sci-pm-domain"
-- #power-domain-cells: Must be 1 so that an id can be provided in each
-		       device node.
+- #power-domain-cells: Can be one of the following:
+			1: Containing the device id of each node
+			2: First entry should be device id
+			   Second entry should be one of the floowing:
+			   TI_SCI_PD_EXCLUSIVE: To allow device to be
+						exclusively controlled by
+						the requesting hosts.
+			   TI_SCI_PD_SHARED: To allow device to be shared
+					     by multiple hosts.
 
 Example (K2G):
 -------------