kbuild: doc: merge 'Special Rules' and 'Custom kbuild commands' sections

The two sections "3.10 Special Rules" and "7.8 Custom kbuild commands"
are related because you must understand both of them when you write
custom rules.

Actually I do not understand the policy about what to go into
"3 The kbuild files" and what into "7 Architecture Makefile".

This commit reworks the custom rule explanation as follows:

 - Merged "7.8 Custom kbuild commands" into "3.10 Special Rules".

 - Reword "Special Rules" to "Custom Rules" for consistency.

 - Update the example for kecho because the blackfin Makefile
   does not exist any more.

 - Replace the example for cmd_<command> with a simpler one.

Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

1 files changed, 40 insertions, 48 deletions

diff --git a/Documentation/kbuild/makefiles.rst b/Documentation/kbuild/makefiles.rst
index 9636e81bed78..87ff7c677749 100644
--- a/Documentation/kbuild/makefiles.rst
+++ b/Documentation/kbuild/makefiles.rst
@@ -18,7 +18,7 @@ This document describes the Linux kernel Makefiles.
 	   --- 3.7 Compilation flags
 	   --- 3.8 <deleted>
 	   --- 3.9 Dependency tracking
-	   --- 3.10 Special Rules
+	   --- 3.10 Custom Rules
 	   --- 3.11 $(CC) support functions
 	   --- 3.12 $(LD) support functions
 	   --- 3.13 Script Invocation
@@ -46,7 +46,7 @@ This document describes the Linux kernel Makefiles.
 	   --- 7.5 Architecture-specific boot images
 	   --- 7.6 Building non-kbuild targets
 	   --- 7.7 Commands useful for building a boot image
-	   --- 7.8 Custom kbuild commands
+	   --- 7.8 <deleted>
 	   --- 7.9 Preprocessing linker scripts
 	   --- 7.10 Generic header files
 	   --- 7.11 Post-link pass
@@ -422,21 +422,21 @@ more details, with real examples.
 	Thus, if you change an option to $(CC) all affected files will
 	be re-compiled.
 
-3.10 Special Rules
+3.10 Custom Rules
 ------------------
 
-	Special rules are used when the kbuild infrastructure does
+	Custom rules are used when the kbuild infrastructure does
 	not provide the required support. A typical example is
 	header files generated during the build process.
 	Another example are the architecture-specific Makefiles which
-	need special rules to prepare boot images etc.
+	need custom rules to prepare boot images etc.
 
-	Special rules are written as normal Make rules.
+	Custom rules are written as normal Make rules.
 	Kbuild is not executing in the directory where the Makefile is
-	located, so all special rules shall provide a relative
+	located, so all custom rules shall use a relative
 	path to prerequisite files and target files.
 
-	Two variables are used when defining special rules:
+	Two variables are used when defining custom rules:
 
 	$(src)
 	    $(src) is a relative path which points to the directory
@@ -454,7 +454,7 @@ more details, with real examples.
 		$(obj)/53c8xx_d.h: $(src)/53c7,8xx.scr $(src)/script_asm.pl
 			$(CPP) -DCHIP=810 - < $< | ... $(src)/script_asm.pl
 
-	    This is a special rule, following the normal syntax
+	    This is a custom rule, following the normal syntax
 	    required by make.
 
 	    The target file depends on two prerequisite files. References
@@ -471,11 +471,33 @@ more details, with real examples.
 
 	Example::
 
-		#arch/blackfin/boot/Makefile
-		$(obj)/vmImage: $(obj)/vmlinux.gz
-			$(call if_changed,uimage)
-			@$(kecho) 'Kernel: $@ is ready'
+		# arch/arm/Makefile
+		$(BOOT_TARGETS): vmlinux
+			$(Q)$(MAKE) $(build)=$(boot) MACHINE=$(MACHINE) $(boot)/$@
+			@$(kecho) '  Kernel: $(boot)/$@ is ready'
 
+	When kbuild is executing with KBUILD_VERBOSE=0, then only a shorthand
+	of a command is normally displayed.
+	To enable this behaviour for custom commands kbuild requires
+	two variables to be set::
+
+		quiet_cmd_<command>	- what shall be echoed
+		      cmd_<command>	- the command to execute
+
+	Example::
+
+		# lib/Makefile
+		quiet_cmd_crc32 = GEN     $@
+		      cmd_crc32 = $< > $@
+
+		$(obj)/crc32table.h: $(obj)/gen_crc32table
+			$(call cmd,crc32)
+
+	When updating the $(obj)/crc32table.h target, the line:
+
+		  GEN     lib/crc32table.h
+
+	will be displayed with "make KBUILD_VERBOSE=0".
 
 3.11 $(CC) support functions
 ----------------------------
@@ -744,7 +766,7 @@ Both possibilities are described in the following.
 	as a prerequisite.
 	This is possible in two ways:
 
-	(1) List the prerequisite explicitly in a special rule.
+	(1) List the prerequisite explicitly in a custom rule.
 
 	Example::
 
@@ -755,11 +777,11 @@ Both possibilities are described in the following.
 
 	The target $(obj)/devlist.h will not be built before
 	$(obj)/gen-devlist is updated. Note that references to
-	the host programs in special rules must be prefixed with $(obj).
+	the host programs in custom rules must be prefixed with $(obj).
 
 	(2) Use always-y
 
-	When there is no suitable special rule, and the host program
+	When there is no suitable custom rule, and the host program
 	shall be built when a makefile is entered, the always-y
 	variable shall be used.
 
@@ -1281,8 +1303,8 @@ When kbuild executes, the following steps are followed (roughly):
 	otherwise the command line check will fail, and the target will
 	always be built.
 	Assignments to $(targets) are without $(obj)/ prefix.
-	if_changed may be used in conjunction with custom commands as
-	defined in 7.8 "Custom kbuild commands".
+	if_changed may be used in conjunction with custom rules as
+	defined in "3.10 Custom Rules".
 
 	Note: It is a typical mistake to forget the FORCE prerequisite.
 	Another common pitfall is that whitespace is sometimes
@@ -1362,36 +1384,6 @@ When kbuild executes, the following steps are followed (roughly):
 		targets += $(dtb-y)
 		DTC_FLAGS ?= -p 1024
 
-7.8 Custom kbuild commands
---------------------------
-
-	When kbuild is executing with KBUILD_VERBOSE=0, then only a shorthand
-	of a command is normally displayed.
-	To enable this behaviour for custom commands kbuild requires
-	two variables to be set::
-
-		quiet_cmd_<command>	- what shall be echoed
-		      cmd_<command>	- the command to execute
-
-	Example::
-
-		#
-		quiet_cmd_image = BUILD   $@
-		      cmd_image = $(obj)/tools/build $(BUILDFLAGS) \
-		                                     $(obj)/vmlinux.bin > $@
-
-		targets += bzImage
-		$(obj)/bzImage: $(obj)/vmlinux.bin $(obj)/tools/build FORCE
-			$(call if_changed,image)
-			@echo 'Kernel: $@ is ready'
-
-	When updating the $(obj)/bzImage target, the line:
-
-		BUILD    arch/x86/boot/bzImage
-
-	will be displayed with "make KBUILD_VERBOSE=0".
-
-
 7.9 Preprocessing linker scripts
 --------------------------------