[media] doc-rst: move bttv documentation to bttv.rst file

There were several files under Documentation/video4linux/bttv.

Instead of simply copying them to the rst folder, I opted to
merge into a single document and adjust the headers to
adjust the section levels and fix the cards tables.

There are two exceptions on the merge:

- The Tuners were renamed as a separate document, as they
  describe a separate driver;

- I removed the PROBLEMS section. It describes problems with
  the very first generation of 3D boards (Mistique/S3).
  It sounds very unlikely that someone would still need to
  install a bttv board on such hardware. Also, it is not
  very well written, IMHO.

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

17 files changed, 1881 insertions, 1763 deletions

diff --git a/Documentation/media/v4l-drivers/bttv.rst b/Documentation/media/v4l-drivers/bttv.rst
new file mode 100644
index 000000000000..d7d956835e38
--- /dev/null
+++ b/Documentation/media/v4l-drivers/bttv.rst
@@ -0,0 +1,1881 @@
+The bttv driver
+===============
+
+
+Release notes for bttv
+----------------------
+
+You'll need at least these config options for bttv:
+	CONFIG_I2C=m
+	CONFIG_I2C_ALGOBIT=m
+	CONFIG_VIDEO_DEV=m
+
+The latest bttv version is available from http://bytesex.org/bttv/
+
+
+Make bttv work with your card
+-----------------------------
+
+Just try "modprobe bttv" and see if that works.
+
+If it doesn't bttv likely could not autodetect your card and needs some
+insmod options.  The most important insmod option for bttv is "card=n"
+to select the correct card type.  If you get video but no sound you've
+very likely specified the wrong (or no) card type.  A list of supported
+cards is in CARDLIST.bttv
+
+If bttv takes very long to load (happens sometimes with the cheap
+cards which have no tuner), try adding this to your modules.conf:
+	options i2c-algo-bit bit_test=1
+
+For the WinTV/PVR you need one firmware file from the driver CD:
+hcwamc.rbf.  The file is in the pvr45xxx.exe archive (self-extracting
+zip file, unzip can unpack it).  Put it into the /etc/pvr directory or
+use the firm_altera=<path> insmod option to point the driver to the
+location of the file.
+
+If your card isn't listed in CARDLIST.bttv or if you have trouble making
+audio work, you should read the Sound-FAQ.
+
+
+Autodetecting cards
+-------------------
+
+bttv uses the PCI Subsystem ID to autodetect the card type.  lspci lists
+the Subsystem ID in the second line, looks like this:
+
+00:0a.0 Multimedia video controller: Brooktree Corporation Bt878 (rev 02)
+	Subsystem: Hauppauge computer works Inc. WinTV/GO
+	Flags: bus master, medium devsel, latency 32, IRQ 5
+	Memory at e2000000 (32-bit, prefetchable) [size=4K]
+
+only bt878-based cards can have a subsystem ID (which does not mean
+that every card really has one).  bt848 cards can't have a Subsystem
+ID and therefore can't be autodetected.  There is a list with the ID's
+in bttv-cards.c (in case you are intrested or want to mail patches
+with updates).
+
+
+Still doesn't work?
+-------------------
+
+I do NOT have a lab with 30+ different grabber boards and a
+PAL/NTSC/SECAM test signal generator at home, so I often can't
+reproduce your problems.  This makes debugging very difficult for me.
+If you have some knowledge and spare time, please try to fix this
+yourself (patches very welcome of course...)  You know: The linux
+slogan is "Do it yourself".
+
+There is a mailing list: linux-media@vger.kernel.org
+http://vger.kernel.org/vger-lists.html#linux-media
+
+If you have trouble with some specific TV card, try to ask there
+instead of mailing me directly.  The chance that someone with the
+same card listens there is much higher...
+
+For problems with sound:  There are a lot of different systems used
+for TV sound all over the world.  And there are also different chips
+which decode the audio signal.  Reports about sound problems ("stereo
+does'nt work") are pretty useless unless you include some details
+about your hardware and the TV sound scheme used in your country (or
+at least the country you are living in).
+
+Modprobe options
+----------------
+
+Note: "modinfo <module>" prints various information about a kernel
+module, among them a complete and up-to-date list of insmod options.
+This list tends to be outdated because it is updated manually ...
+
+==========================================================================
+
+bttv.o
+
+::
+
+	the bt848/878 (grabber chip) driver
+
+	insmod args:
+		card=n		card type, see CARDLIST for a list.
+		tuner=n		tuner type, see CARDLIST for a list.
+		radio=0/1	card supports radio
+		pll=0/1/2	pll settings
+			0: don't use PLL
+			1: 28 MHz crystal installed
+			2: 35 MHz crystal installed
+
+		triton1=0/1     for Triton1 (+others) compatibility
+		vsfx=0/1	yet another chipset bug compatibility bit
+				see README.quirks for details on these two.
+
+		bigendian=n	Set the endianness of the gfx framebuffer.
+				Default is native endian.
+		fieldnr=0/1	Count fields.  Some TV descrambling software
+				needs this, for others it only generates
+				50 useless IRQs/sec.  default is 0 (off).
+		autoload=0/1	autoload helper modules (tuner, audio).
+				default is 1 (on).
+		bttv_verbose=0/1/2  verbose level (at insmod time, while
+				looking at the hardware).  default is 1.
+		bttv_debug=0/1	debug messages (for capture).
+				default is 0 (off).
+		irq_debug=0/1	irq handler debug messages.
+				default is 0 (off).
+		gbuffers=2-32	number of capture buffers for mmap'ed capture.
+				default is 4.
+		gbufsize=	size of capture buffers. default and
+				maximum value is 0x208000 (~2MB)
+		no_overlay=0	Enable overlay on broken hardware.  There
+				are some chipsets (SIS for example) which
+				are known to have problems with the PCI DMA
+				push used by bttv.  bttv will disable overlay
+				by default on this hardware to avoid crashes.
+				With this insmod option you can override this.
+		no_overlay=1	Disable overlay. It should be used by broken
+				hardware that doesn't support PCI2PCI direct
+				transfers.
+		automute=0/1	Automatically mutes the sound if there is
+				no TV signal, on by default.  You might try
+				to disable this if you have bad input signal
+				quality which leading to unwanted sound
+				dropouts.
+		chroma_agc=0/1	AGC of chroma signal, off by default.
+		adc_crush=0/1	Luminance ADC crush, on by default.
+		i2c_udelay=     Allow reduce I2C speed. Default is 5 usecs
+				(meaning 66,67 Kbps). The default is the
+				maximum supported speed by kernel bitbang
+				algorithm. You may use lower numbers, if I2C
+				messages are lost (16 is known to work on
+				all supported cards).
+
+		bttv_gpio=0/1
+		gpiomask=
+		audioall=
+		audiomux=
+				See Sound-FAQ for a detailed description.
+
+	remap, card, radio and pll accept up to four comma-separated arguments
+	(for multiple boards).
+
+tuner.o
+
+::
+
+	The tuner driver.  You need this unless you want to use only
+	with a camera or external tuner ...
+
+	insmod args:
+		debug=1		print some debug info to the syslog
+		type=n		type of the tuner chip. n as follows:
+				see CARDLIST for a complete list.
+		pal=[bdgil]	select PAL variant (used for some tuners
+				only, important for the audio carrier).
+
+tvaudio.o
+
+::
+
+	new, experimental module which is supported to provide a single
+	driver for all simple i2c audio control chips (tda/tea*).
+
+	insmod args:
+		tda8425  = 1	enable/disable the support for the
+		tda9840  = 1	various chips.
+		tda9850  = 1	The tea6300 can't be autodetected and is
+		tda9855  = 1	therefore off by default, if you have
+		tda9873  = 1	this one on your card (STB uses these)
+		tda9874a = 1	you have to enable it explicitly.
+		tea6300  = 0	The two tda985x chips use the same i2c
+		tea6420  = 1	address and can't be disturgished from
+		pic16c54 = 1	each other, you might have to disable
+				the wrong one.
+		debug = 1	print debug messages
+
+	insmod args for tda9874a:
+		tda9874a_SIF=1/2	select sound IF input pin (1 or 2)
+					(default is pin 1)
+		tda9874a_AMSEL=0/1	auto-mute select for NICAM (default=0)
+					Please read note 3 below!
+		tda9874a_STD=n		select TV sound standard (0..8):
+					0 - A2, B/G
+					1 - A2, M (Korea)
+					2 - A2, D/K (1)
+					3 - A2, D/K (2)
+					4 - A2, D/K (3)
+					5 - NICAM, I
+					6 - NICAM, B/G
+					7 - NICAM, D/K (default)
+					8 - NICAM, L
+
+	Note 1: tda9874a supports both tda9874h (old) and tda9874a (new) chips.
+	Note 2: tda9874h/a and tda9875 (which is supported separately by
+	tda9875.o) use the same i2c address so both modules should not be
+	used at the same time.
+	Note 3: Using tda9874a_AMSEL option depends on your TV card design!
+		AMSEL=0: auto-mute will switch between NICAM sound
+			 and the sound on 1st carrier (i.e. FM mono or AM).
+		AMSEL=1: auto-mute will switch between NICAM sound
+			 and the analog mono input (MONOIN pin).
+	If tda9874a decoder on your card has MONOIN pin not connected, then
+	use only tda9874_AMSEL=0 or don't specify this option at all.
+	For example:
+	  card=65 (FlyVideo 2000S) - set AMSEL=1 or AMSEL=0
+	  card=72 (Prolink PV-BT878P rev.9B) - set AMSEL=0 only
+
+msp3400.o
+
+::
+
+
+	The driver for the msp34xx sound processor chips. If you have a
+	stereo card, you probably want to insmod this one.
+
+	insmod args:
+		debug=1/2	print some debug info to the syslog,
+				2 is more verbose.
+		simple=1	Use the "short programming" method.  Newer
+				msp34xx versions support this.  You need this
+				for dbx stereo.  Default is on if supported by
+				the chip.
+		once=1		Don't check the TV-stations Audio mode
+				every few seconds, but only once after
+				channel switches.
+		amsound=1	Audio carrier is AM/NICAM at 6.5 Mhz.  This
+				should improve things for french people, the
+				carrier autoscan seems to work with FM only...
+
+tea6300.o - OBSOLETE (use tvaudio instead)
+
+::
+
+	The driver for the tea6300 fader chip.  If you have a stereo
+	card and the msp3400.o doesn't work, you might want to try this
+	one.  This chip is seen on most STB TV/FM cards (usually from
+	Gateway OEM sold surplus on auction sites).
+
+	insmod args:
+		debug=1		print some debug info to the syslog.
+
+tda8425.o - OBSOLETE (use tvaudio instead)
+
+::
+
+	The driver for the tda8425 fader chip.  This driver used to be
+	part of bttv.c, so if your sound used to work but does not
+	anymore, try loading this module.
+
+	insmod args:
+		debug=1		print some debug info to the syslog.
+
+tda985x.o - OBSOLETE (use tvaudio instead)
+
+::
+
+	The driver for the tda9850/55 audio chips.
+
+	insmod args:
+		debug=1		print some debug info to the syslog.
+		chip=9850/9855	set the chip type.
+
+
+If the box freezes hard with bttv
+---------------------------------
+
+It might be a bttv driver bug.  It also might be bad hardware.  It also
+might be something else ...
+
+Just mailing me "bttv freezes" isn't going to help much.  This README
+has a few hints how you can help to pin down the problem.
+
+
+bttv bugs
+~~~~~~~~~
+
+If some version works and another doesn't it is likely to be a driver
+bug.  It is very helpful if you can tell where exactly it broke
+(i.e. the last working and the first broken version).
+
+With a hard freeze you probably doesn't find anything in the logfiles.
+The only way to capture any kernel messages is to hook up a serial
+console and let some terminal application log the messages.  /me uses
+screen.  See Documentation/serial-console.txt for details on setting
+up a serial console.
+
+Read Documentation/oops-tracing.txt to learn how to get any useful
+information out of a register+stack dump printed by the kernel on
+protection faults (so-called "kernel oops").
+
+If you run into some kind of deadlock, you can try to dump a call trace
+for each process using sysrq-t (see Documentation/sysrq.txt).
+This way it is possible to figure where *exactly* some process in "D"
+state is stuck.
+
+I've seen reports that bttv 0.7.x crashes whereas 0.8.x works rock solid
+for some people.  Thus probably a small buglet left somewhere in bttv
+0.7.x.  I have no idea where exactly, it works stable for me and a lot of
+other people.  But in case you have problems with the 0.7.x versions you
+can give 0.8.x a try ...
+
+
+hardware bugs
+~~~~~~~~~~~~~
+
+Some hardware can't deal with PCI-PCI transfers (i.e. grabber => vga).
+Sometimes problems show up with bttv just because of the high load on
+the PCI bus. The bt848/878 chips have a few workarounds for known
+incompatibilities, see README.quirks.
+
+Some folks report that increasing the pci latency helps too,
+althrought I'm not sure whenever this really fixes the problems or
+only makes it less likely to happen.  Both bttv and btaudio have a
+insmod option to set the PCI latency of the device.
+
+Some mainboard have problems to deal correctly with multiple devices
+doing DMA at the same time.  bttv + ide seems to cause this sometimes,
+if this is the case you likely see freezes only with video and hard disk
+access at the same time.  Updating the IDE driver to get the latest and
+greatest workarounds for hardware bugs might fix these problems.
+
+
+other
+~~~~~
+
+If you use some binary-only yunk (like nvidia module) try to reproduce
+the problem without.
+
+IRQ sharing is known to cause problems in some cases.  It works just
+fine in theory and many configurations.  Neverless it might be worth a
+try to shuffle around the PCI cards to give bttv another IRQ or make
+it share the IRQ with some other piece of hardware.  IRQ sharing with
+VGA cards seems to cause trouble sometimes.  I've also seen funny
+effects with bttv sharing the IRQ with the ACPI bridge (and
+apci-enabled kernel).
+
+Bttv quirks
+-----------
+
+Below is what the bt878 data book says about the PCI bug compatibility
+modes of the bt878 chip.
+
+The triton1 insmod option sets the EN_TBFX bit in the control register.
+The vsfx insmod option does the same for EN_VSFX bit.  If you have
+stability problems you can try if one of these options makes your box
+work solid.
+
+drivers/pci/quirks.c knows about these issues, this way these bits are
+enabled automagically for known-buggy chipsets (look at the kernel
+messages, bttv tells you).
+
+Normal PCI Mode
+~~~~~~~~~~~~~~~
+
+The PCI REQ signal is the logical-or of the incoming function requests.
+The inter-nal GNT[0:1] signals are gated asynchronously with GNT and
+demultiplexed by the audio request signal. Thus the arbiter defaults to
+the video function at power-up and parks there during no requests for
+bus access. This is desirable since the video will request the bus more
+often. However, the audio will have highest bus access priority. Thus
+the audio will have first access to the bus even when issuing a request
+after the video request but before the PCI external arbiter has granted
+access to the Bt879. Neither function can preempt the other once on the
+bus. The duration to empty the entire video PCI FIFO onto the PCI bus is
+very short compared to the bus access latency the audio PCI FIFO can
+tolerate.
+
+
+430FX Compatibility Mode
+~~~~~~~~~~~~~~~~~~~~~~~~
+
+When using the 430FX PCI, the following rules will ensure
+compatibility:
+
+ (1) Deassert REQ at the same time as asserting FRAME.
+ (2) Do not reassert REQ to request another bus transaction until after
+     finish-ing the previous transaction.
+
+Since the individual bus masters do not have direct control of REQ, a
+simple logical-or of video and audio requests would violate the rules.
+Thus, both the arbiter and the initiator contain 430FX compatibility
+mode logic. To enable 430FX mode, set the EN_TBFX bit as indicated in
+Device Control Register on page 104.
+
+When EN_TBFX is enabled, the arbiter ensures that the two compatibility
+rules are satisfied. Before GNT is asserted by the PCI arbiter, this
+internal arbiter may still logical-or the two requests. However, once
+the GNT is issued, this arbiter must lock in its decision and now route
+only the granted request to the REQ pin. The arbiter decision lock
+happens regardless of the state of FRAME because it does not know when
+FRAME will be asserted (typically - each initiator will assert FRAME on
+the cycle following GNT). When FRAME is asserted, it is the initiator s
+responsibility to remove its request at the same time. It is the
+arbiters responsibility to allow this request to flow through to REQ and
+not allow the other request to hold REQ asserted. The decision lock may
+be removed at the end of the transaction: for example, when the bus is
+idle (FRAME and IRDY). The arbiter decision may then continue
+asynchronously until GNT is again asserted.
+
+
+Interfacing with Non-PCI 2.1 Compliant Core Logic
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+A small percentage of core logic devices may start a bus transaction
+during the same cycle that GNT is de-asserted. This is non PCI 2.1
+compliant. To ensure compatibility when using PCs with these PCI
+controllers, the EN_VSFX bit must be enabled (refer to Device Control
+Register on page 104). When in this mode, the arbiter does not pass GNT
+to the internal functions unless REQ is asserted. This prevents a bus
+transaction from starting the same cycle as GNT is de-asserted. This
+also has the side effect of not being able to take advantage of bus
+parking, thus lowering arbitration performance. The Bt879 drivers must
+query for these non-compliant devices, and set the EN_VSFX bit only if
+required.
+
+bttv and sound mini howto
+-------------------------
+
+There are a lot of different bt848/849/878/879 based boards available.
+Making video work often is not a big deal, because this is handled
+completely by the bt8xx chip, which is common on all boards.  But
+sound is handled in slightly different ways on each board.
+
+To handle the grabber boards correctly, there is a array tvcards[] in
+bttv-cards.c, which holds the information required for each board.
+Sound will work only, if the correct entry is used (for video it often
+makes no difference).  The bttv driver prints a line to the kernel
+log, telling which card type is used.  Like this one:
+
+	bttv0: model: BT848(Hauppauge old) [autodetected]
+
+You should verify this is correct.  If it isn't, you have to pass the
+correct board type as insmod argument, "insmod bttv card=2" for
+example.  The file CARDLIST has a list of valid arguments for card.
+If your card isn't listed there, you might check the source code for
+new entries which are not listed yet.  If there isn't one for your
+card, you can check if one of the existing entries does work for you
+(just trial and error...).
+
+Some boards have an extra processor for sound to do stereo decoding
+and other nice features.  The msp34xx chips are used by Hauppauge for
+example.  If your board has one, you might have to load a helper
+module like msp3400.o to make sound work.  If there isn't one for the
+chip used on your board:  Bad luck.  Start writing a new one.  Well,
+you might want to check the video4linux mailing list archive first...
+
+Of course you need a correctly installed soundcard unless you have the
+speakers connected directly to the grabber board.  Hint: check the
+mixer settings too.  ALSA for example has everything muted by default.
+
+
+How sound works in detail
+~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Still doesn't work?  Looks like some driver hacking is required.
+Below is a do-it-yourself description for you.
+
+The bt8xx chips have 32 general purpose pins, and registers to control
+these pins.  One register is the output enable register
+(BT848_GPIO_OUT_EN), it says which pins are actively driven by the
+bt848 chip.  Another one is the data register (BT848_GPIO_DATA), where
+you can get/set the status if these pins.  They can be used for input
+and output.
+
+Most grabber board vendors use these pins to control an external chip
+which does the sound routing.  But every board is a little different.
+These pins are also used by some companies to drive remote control
+receiver chips.  Some boards use the i2c bus instead of the gpio pins
+to connect the mux chip.
+
+As mentioned above, there is a array which holds the required
+information for each known board.  You basically have to create a new
+line for your board.  The important fields are these two:
+
+struct tvcard
+{
+	[ ... ]
+	u32 gpiomask;
+	u32 audiomux[6]; /* Tuner, Radio, external, internal, mute, stereo */
+};
+
+gpiomask specifies which pins are used to control the audio mux chip.
+The corresponding bits in the output enable register
+(BT848_GPIO_OUT_EN) will be set as these pins must be driven by the
+bt848 chip.
+
+The audiomux[] array holds the data values for the different inputs
+(i.e. which pins must be high/low for tuner/mute/...).  This will be
+written to the data register (BT848_GPIO_DATA) to switch the audio
+mux.
+
+
+What you have to do is figure out the correct values for gpiomask and
+the audiomux array.  If you have Windows and the drivers four your
+card installed, you might to check out if you can read these registers
+values used by the windows driver.  A tool to do this is available
+from ftp://telepresence.dmem.strath.ac.uk/pub/bt848/winutil, but it
+does'nt work with bt878 boards according to some reports I received.
+Another one with bt878 support is available from
+http://btwincap.sourceforge.net/Files/btspy2.00.zip
+
+You might also dig around in the *.ini files of the Windows applications.
+You can have a look at the board to see which of the gpio pins are
+connected at all and then start trial-and-error ...
+
+
+Starting with release 0.7.41 bttv has a number of insmod options to
+make the gpio debugging easier:
+
+bttv_gpio=0/1		enable/disable gpio debug messages
+gpiomask=n		set the gpiomask value
+audiomux=i,j,...	set the values of the audiomux array
+audioall=a		set the values of the audiomux array (one
+			value for all array elements, useful to check
+			out which effect the particular value has).
+
+The messages printed with bttv_gpio=1 look like this:
+
+	bttv0: gpio: en=00000027, out=00000024 in=00ffffd8 [audio: off]
+
+en  =	output _en_able register (BT848_GPIO_OUT_EN)
+out =	_out_put bits of the data register (BT848_GPIO_DATA),
+	i.e. BT848_GPIO_DATA & BT848_GPIO_OUT_EN
+in  = 	_in_put bits of the data register,
+	i.e. BT848_GPIO_DATA & ~BT848_GPIO_OUT_EN
+
+
+
+Other elements of the tvcards array
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+If you are trying to make a new card work you might find it useful to
+know what the other elements in the tvcards array are good for:
+
+video_inputs    - # of video inputs the card has
+audio_inputs    - historical cruft, not used any more.
+tuner           - which input is the tuner
+svhs            - which input is svhs (all others are labeled composite)
+muxsel          - video mux, input->registervalue mapping
+pll             - same as pll= insmod option
+tuner_type      - same as tuner= insmod option
+*_modulename    - hint whenever some card needs this or that audio
+		  module loaded to work properly.
+has_radio	- whenever this TV card has a radio tuner.
+no_msp34xx	- "1" disables loading of msp3400.o module
+no_tda9875	- "1" disables loading of tda9875.o module
+needs_tvaudio	- set to "1" to load tvaudio.o module
+
+If some config item is specified both from the tvcards array and as
+insmod option, the insmod option takes precedence.
+
+Cards
+-----
+
+.. note::
+   For a more updated list, please check
+   https://linuxtv.org/wiki/index.php/Hardware_Device_Information
+
+Supported cards: Bt848/Bt848a/Bt849/Bt878/Bt879 cards
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+All cards with Bt848/Bt848a/Bt849/Bt878/Bt879 and normal
+Composite/S-VHS inputs are supported.  Teletext and Intercast support
+(PAL only) for ALL cards via VBI sample decoding in software.
+
+Some cards with additional multiplexing of inputs or other additional
+fancy chips are only partially supported (unless specifications by the
+card manufacturer are given).  When a card is listed here it isn't
+necessarily fully supported.
+
+All other cards only differ by additional components as tuners, sound
+decoders, EEPROMs, teletext decoders ...
+
+
+MATRIX Vision
+~~~~~~~~~~~~~
+
+MV-Delta
+- Bt848A
+- 4 Composite inputs, 1 S-VHS input (shared with 4th composite)
+- EEPROM
+
+http://www.matrix-vision.de/
+
+This card has no tuner but supports all 4 composite (1 shared with an
+S-VHS input) of the Bt848A.
+Very nice card if you only have satellite TV but several tuners connected
+to the card via composite.
+
+Many thanks to Matrix-Vision for giving us 2 cards for free which made
+Bt848a/Bt849 single crystal operation support possible!!!
+
+
+
+Miro/Pinnacle PCTV
+~~~~~~~~~~~~~~~~~~
+
+- Bt848
+  some (all??) come with 2 crystals for PAL/SECAM and NTSC
+- PAL, SECAM or NTSC TV tuner (Philips or TEMIC)
+- MSP34xx sound decoder on add on board
+  decoder is supported but AFAIK does not yet work
+  (other sound MUX setting in GPIO port needed??? somebody who fixed this???)
+- 1 tuner, 1 composite and 1 S-VHS input
+- tuner type is autodetected
+
+http://www.miro.de/
+http://www.miro.com/
+
+
+Many thanks for the free card which made first NTSC support possible back
+in 1997!
+
+
+Hauppauge Win/TV pci
+~~~~~~~~~~~~~~~~~~~~
+
+There are many different versions of the Hauppauge cards with different
+tuners (TV+Radio ...), teletext decoders.
+Note that even cards with same model numbers have (depending on the revision)
+different chips on it.
+
+- Bt848 (and others but always in 2 crystal operation???)
+  newer cards have a Bt878
+
+- PAL, SECAM, NTSC or tuner with or without Radio support
+
+e.g.:
+
+- PAL:
+
+  - TDA5737: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners
+  - TSA5522: 1.4 GHz I2C-bus controlled synthesizer, I2C 0xc2-0xc3
+
+- NTSC:
+
+  - TDA5731: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners
+  - TSA5518: no datasheet available on Philips site
+
+- Philips SAA5246 or SAA5284 ( or no) Teletext decoder chip
+  with buffer RAM (e.g. Winbond W24257AS-35: 32Kx8 CMOS static RAM)
+  SAA5246 (I2C 0x22) is supported
+
+- 256 bytes EEPROM: Microchip 24LC02B or Philips 8582E2Y
+  with configuration information
+  I2C address 0xa0 (24LC02B also responds to 0xa2-0xaf)
+
+- 1 tuner, 1 composite and (depending on model) 1 S-VHS input
+
+- 14052B: mux for selection of sound source
+
+- sound decoder: TDA9800, MSP34xx (stereo cards)
+
+
+Askey CPH-Series
+~~~~~~~~~~~~~~~~
+Developed by TelSignal(?), OEMed by many vendors (Typhoon, Anubis, Dynalink)
+
+- Card series:
+  - CPH01x: BT848 capture only
+  - CPH03x: BT848
+  - CPH05x: BT878 with FM
+  - CPH06x: BT878 (w/o FM)
+  - CPH07x: BT878 capture only
+
+- TV standards:
+  - CPH0x0: NTSC-M/M
+  - CPH0x1: PAL-B/G
+  - CPH0x2: PAL-I/I
+  - CPH0x3: PAL-D/K
+  - CPH0x4: SECAM-L/L
+  - CPH0x5: SECAM-B/G
+  - CPH0x6: SECAM-D/K
+  - CPH0x7: PAL-N/N
+  - CPH0x8: PAL-B/H
+  - CPH0x9: PAL-M/M
+
+- CPH03x was often sold as "TV capturer".
+
+Identifying:
+
+  #) 878 cards can be identified by PCI Subsystem-ID:
+     - 144f:3000 = CPH06x
+     - 144F:3002 = CPH05x w/ FM
+     - 144F:3005 = CPH06x_LC (w/o remote control)
+  #) The cards have a sticker with "CPH"-model on the back.
+  #) These cards have a number printed on the PCB just above the tuner metal box:
+     - "80-CP2000300-x" = CPH03X
+     - "80-CP2000500-x" = CPH05X
+     - "80-CP2000600-x" = CPH06X / CPH06x_LC
+
+  Askey sells these cards as "Magic TView series", Brand "MagicXpress".
+  Other OEM often call these "Tview", "TView99" or else.
+
+Lifeview Flyvideo Series:
+~~~~~~~~~~~~~~~~~~~~~~~~~
+
+The naming of these series differs in time and space.
+
+Identifying:
+  #) Some models can be identified by PCI subsystem ID:
+
+     - 1852:1852 = Flyvideo 98 FM
+     - 1851:1850 = Flyvideo 98
+     - 1851:1851 = Flyvideo 98 EZ (capture only)
+
+  #) There is a print on the PCB:
+
+     - LR25       = Flyvideo (Zoran ZR36120, SAA7110A)
+     - LR26 Rev.N = Flyvideo II (Bt848)
+     - LR26 Rev.O = Flyvideo II (Bt878)
+     - LR37 Rev.C = Flyvideo EZ (Capture only, ZR36120 + SAA7110)
+     - LR38 Rev.A1= Flyvideo II EZ (Bt848 capture only)
+     - LR50 Rev.Q = Flyvideo 98 (w/eeprom and PCI subsystem ID)
+     - LR50 Rev.W = Flyvideo 98 (no eeprom)
+     - LR51 Rev.E = Flyvideo 98 EZ (capture only)
+     - LR90       = Flyvideo 2000 (Bt878)
+     - LR90 Flyvideo 2000S (Bt878) w/Stereo TV (Package incl. LR91 daughterboard)
+     - LR91       = Stereo daughter card for LR90
+     - LR97       = Flyvideo DVBS
+     - LR99 Rev.E = Low profile card for OEM integration (only internal audio!) bt878
+     - LR136	 = Flyvideo 2100/3100 (Low profile, SAA7130/SAA7134)
+     - LR137      = Flyvideo DV2000/DV3000 (SAA7130/SAA7134 + IEEE1394)
+     - LR138 Rev.C= Flyvideo 2000 (SAA7130)
+     - LR138 Flyvideo 3000 (SAA7134) w/Stereo TV
+	- These exist in variations w/FM and w/Remote sometimes denoted
+	  by suffixes "FM" and "R".
+
+  #) You have a laptop (miniPCI card):
+      - Product    = FlyTV Platinum Mini
+      - Model/Chip = LR212/saa7135
+
+      - Lifeview.com.tw states (Feb. 2002):
+        "The FlyVideo2000 and FlyVideo2000s product name have renamed to FlyVideo98."
+        Their Bt8x8 cards are listed as discontinued.
+      - Flyvideo 2000S was probably sold as Flyvideo 3000 in some contries(Europe?).
+        The new Flyvideo 2000/3000 are SAA7130/SAA7134 based.
+
+"Flyvideo II" had been the name for the 848 cards, nowadays (in Germany)
+this name is re-used for LR50 Rev.W.
+
+The Lifeview website mentioned Flyvideo III at some time, but such a card
+has not yet been seen (perhaps it was the german name for LR90 [stereo]).
+These cards are sold by many OEMs too.
+
+FlyVideo A2 (Elta 8680)= LR90 Rev.F (w/Remote, w/o FM, stereo TV by tda9821) {Germany}
+
+Lifeview 3000 (Elta 8681) as sold by Plus(April 2002), Germany = LR138 w/ saa7134
+
+
+Typhoon TV card series:
+~~~~~~~~~~~~~~~~~~~~~~~
+
+These can be CPH, Flyvideo, Pixelview or KNC1 series.
+Typhoon is the brand of Anubis.
+Model 50680 got re-used, some model no. had different contents over time.
+
+Models:
+
+  - 50680 "TV Tuner PCI Pal BG"(old,red package)=can be CPH03x(bt848) or CPH06x(bt878)
+  - 50680 "TV Tuner Pal BG" (blue package)= Pixelview PV-BT878P+ (Rev 9B)
+  - 50681 "TV Tuner PCI Pal I" (variant of 50680)
+  - 50682 "TView TV/FM Tuner Pal BG"       = Flyvideo 98FM (LR50 Rev.Q)
+
+  .. note::
+
+	 The package has a picture of CPH05x (which would be a real TView)
+
+  - 50683 "TV Tuner PCI SECAM" (variant of 50680)
+  - 50684 "TV Tuner Pal BG"                = Pixelview 878TV(Rev.3D)
+  - 50686 "TV Tuner"                       = KNC1 TV Station
+  - 50687 "TV Tuner stereo"                = KNC1 TV Station pro
+  - 50688 "TV Tuner RDS" (black package)   = KNC1 TV Station RDS
+  - 50689  TV SAT DVB-S CARD CI PCI (SAA7146AH, SU1278?) = "KNC1 TV Station DVB-S"
+  - 50692 "TV/FM Tuner" (small PCB)
+  - 50694  TV TUNER CARD RDS (PHILIPS CHIPSET SAA7134HL)
+  - 50696  TV TUNER STEREO (PHILIPS CHIPSET SAA7134HL, MK3ME Tuner)
+  - 50804  PC-SAT TV/Audio Karte = Techni-PC-Sat (ZORAN 36120PQC, Tuner:Alps)
+  - 50866  TVIEW SAT RECEIVER+ADR
+  - 50868 "TV/FM Tuner Pal I" (variant of 50682)
+  - 50999 "TV/FM Tuner Secam" (variant of 50682)
+
+Guillemot
+~~~~~~~~~
+
+Models:
+
+- Maxi-TV PCI (ZR36120)
+- Maxi TV Video 2 = LR50 Rev.Q (FI1216MF, PAL BG+SECAM)
+- Maxi TV Video 3 = CPH064 (PAL BG + SECAM)
+
+Mentor
+~~~~~~
+
+Mentor TV card ("55-878TV-U1") = Pixelview 878TV(Rev.3F) (w/FM w/Remote)
+
+Prolink
+~~~~~~~
+
+- TV cards:
+
+  - PixelView Play TV pro - (Model: PV-BT878P+ REV 8E)
+  - PixelView Play TV pro - (Model: PV-BT878P+ REV 9D)
+  - PixelView Play TV pro - (Model: PV-BT878P+ REV 4C / 8D / 10A )
+  - PixelView Play TV - (Model: PV-BT848P+)
+  - 878TV - (Model: PV-BT878TV)
+
+- Multimedia TV packages (card + software pack):
+
+  - PixelView Play TV Theater - (Model: PV-M4200) =  PixelView Play TV pro + Software
+  - PixelView Play TV PAK -     (Model: PV-BT878P+ REV 4E)
+  - PixelView Play TV/VCR -     (Model: PV-M3200 REV 4C / 8D / 10A )
+  - PixelView Studio PAK -      (Model:    M2200 REV 4C / 8D / 10A )
+  - PixelView PowerStudio PAK - (Model: PV-M3600 REV 4E)
+  - PixelView DigitalVCR PAK -  (Model: PV-M2400 REV 4C / 8D / 10A )
+  - PixelView PlayTV PAK II (TV/FM card + usb camera)  PV-M3800
+  - PixelView PlayTV XP PV-M4700,PV-M4700(w/FM)
+  - PixelView PlayTV DVR PV-M4600  package contents:PixelView PlayTV pro, windvr & videoMail s/w
+
+- Further Cards:
+
+  - PV-BT878P+rev.9B (Play TV Pro, opt. w/FM w/NICAM)
+  - PV-BT878P+rev.2F
+  - PV-BT878P Rev.1D (bt878, capture only)
+
+  - XCapture PV-CX881P (cx23881)
+  - PlayTV HD PV-CX881PL+, PV-CX881PL+(w/FM) (cx23881)
+
+  - DTV3000 PV-DTV3000P+ DVB-S CI = Twinhan VP-1030
+  - DTV2000 DVB-S = Twinhan VP-1020
+
+- Video Conferencing:
+
+  - PixelView Meeting PAK - (Model: PV-BT878P)
+  - PixelView Meeting PAK Lite - (Model: PV-BT878P)
+  - PixelView Meeting PAK plus - (Model: PV-BT878P+rev 4C/8D/10A)
+  - PixelView Capture - (Model: PV-BT848P)
+  - PixelView PlayTV USB pro
+  - Model No. PV-NT1004+, PV-NT1004+ (w/FM) = NT1004 USB decoder chip + SAA7113 video decoder chip
+
+Dynalink
+~~~~~~~~
+
+These are CPH series.
+
+Phoebemicro
+~~~~~~~~~~~
+
+- TV Master    = CPH030 or CPH060
+- TV Master FM = CPH050
+
+Genius/Kye
+~~~~~~~~~~
+
+- Video Wonder/Genius Internet Video Kit = LR37 Rev.C
+- Video Wonder Pro II (848 or 878) = LR26
+
+Tekram
+~~~~~~
+
+- VideoCap C205 (Bt848)
+- VideoCap C210 (zr36120 +Philips)
+- CaptureTV M200 (ISA)
+- CaptureTV M205 (Bt848)
+
+Lucky Star
+~~~~~~~~~~
+
+- Image World Conference TV = LR50 Rev. Q
+
+Leadtek
+~~~~~~~
+
+- WinView 601 (Bt848)
+- WinView 610 (Zoran)
+- WinFast2000
+- WinFast2000 XP
+
+Support for the Leadtek WinView 601 TV/FM
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+Author of this section: Jon Tombs <jon@gte.esi.us.es>
+
+This card is basically the same as all the rest (Bt484A, Philips tuner),
+the main difference is that they have attached a programmable attenuator to 3
+GPIO lines in order to give some volume control. They have also stuck an
+infra-red remote control decoded on the board, I will add support for this
+when I get time (it simple generates an interrupt for each key press, with
+the key code is placed in the GPIO port).
+
+I don't yet have any application to test the radio support. The tuner
+frequency setting should work but it is possible that the audio multiplexer
+is wrong. If it doesn't work, send me email.
+
+
+- No Thanks to Leadtek they refused to answer any questions about their
+hardware. The driver was written by visual inspection of the card. If you
+use this driver, send an email insult to them, and tell them you won't
+continue buying their hardware unless they support Linux.
+
+- Little thanks to Princeton Technology Corp (http://www.princeton.com.tw)
+who make the audio attenuator. Their publicly available data-sheet available
+on their web site doesn't include the chip programming information! Hidden
+on their server are the full data-sheets, but don't ask how I found it.
+
+To use the driver I use the following options, the tuner and pll settings might
+be different in your country
+
+insmod videodev
+insmod i2c scan=1 i2c_debug=0 verbose=0
+insmod tuner type=1 debug=0
+insmod bttv  pll=1 radio=1 card=17
+
+
+KNC One
+~~~~~~~
+
+- TV-Station
+- TV-Station SE (+Software Bundle)
+- TV-Station pro (+TV stereo)
+- TV-Station FM (+Radio)
+- TV-Station RDS (+RDS)
+- TV Station SAT (analog satellite)
+- TV-Station DVB-S
+
+.. note:: newer Cards have saa7134, but model name stayed the same?
+
+Provideo
+~~~~~~~~
+
+- PV951 or PV-951 (also are sold as:
+   Boeder TV-FM Video Capture Card,
+   Titanmedia Supervision TV-2400,
+   Provideo PV951 TF,
+   3DeMon PV951,
+   MediaForte TV-Vision PV951,
+   Yoko PV951,
+   Vivanco Tuner Card PCI Art.-Nr.: 68404,
+  ) now named PV-951T
+
+- Surveillance Series:
+
+ - PV-141
+ - PV-143
+ - PV-147
+ - PV-148 (capture only)
+ - PV-150
+ - PV-151
+
+- TV-FM Tuner Series:
+
+ - PV-951TDV (tv tuner + 1394)
+ - PV-951T/TF
+ - PV-951PT/TF
+ - PV-956T/TF Low Profile
+ - PV-911
+
+Highscreen
+~~~~~~~~~~
+
+Models:
+
+- TV Karte = LR50 Rev.S
+- TV-Boostar = Terratec Terra TV+ Version 1.0 (Bt848, tda9821) "ceb105.pcb"
+
+Zoltrix
+~~~~~~~
+
+Models:
+
+- Face to Face Capture (Bt848 capture only) (PCB "VP-2848")
+- Face To Face TV MAX (Bt848) (PCB "VP-8482 Rev1.3")
+- Genie TV (Bt878) (PCB "VP-8790 Rev 2.1")
+- Genie Wonder Pro
+
+AVerMedia
+~~~~~~~~~
+
+- AVer FunTV Lite (ISA, AV3001 chipset)  "M101.C"
+- AVerTV
+- AVerTV Stereo
+- AVerTV Studio (w/FM)
+- AVerMedia TV98 with Remote
+- AVerMedia TV/FM98 Stereo
+- AVerMedia TVCAM98
+- TVCapture (Bt848)
+- TVPhone (Bt848)
+- TVCapture98 (="AVerMedia TV98" in USA) (Bt878)
+- TVPhone98 (Bt878, w/FM)
+
+======== =========== =============== ======= ====== ======== =======================
+PCB      PCI-ID      Model-Name      Eeprom  Tuner  Sound    Country
+======== =========== =============== ======= ====== ======== =======================
+M101.C   ISA !
+M108-B      Bt848                     --     FR1236		 US   [#f2]_,[#f3]_
+M1A8-A      Bt848    AVer TV-Phone           FM1216  --
+M168-T   1461:0003   AVerTV Studio   48:17   FM1216 TDA9840T  D    [#f1]_ w/FM w/Remote
+M168-U   1461:0004   TVCapture98     40:11   FI1216   --      D    w/Remote
+M168II-B 1461:0003   Medion MD9592   48:16   FM1216 TDA9873H  D    w/FM
+======== =========== =============== ======= ====== ======== =======================
+
+.. [#f1] Daughterboard MB68-A with TDA9820T and TDA9840T
+.. [#f2] Sony NE41S soldered (stereo sound?)
+.. [#f3] Daughterboard M118-A w/ pic 16c54 and 4 MHz quartz
+
+- US site has different drivers for (as of 09/2002):
+
+  - EZ Capture/InterCam PCI (BT-848 chip)
+  - EZ Capture/InterCam PCI (BT-878 chip)
+  - TV-Phone (BT-848 chip)
+  - TV98 (BT-848 chip)
+  - TV98 With Remote (BT-848 chip)
+  - TV98 (BT-878 chip)
+  - TV98 With Remote (BT-878)
+  - TV/FM98 (BT-878 chip)
+  - AVerTV
+  - AverTV Stereo
+  - AVerTV Studio
+
+DE hat diverse Treiber fuer diese Modelle (Stand 09/2002):
+
+  - TVPhone (848) mit Philips tuner FR12X6 (w/ FM radio)
+  - TVPhone (848) mit Philips tuner FM12X6 (w/ FM radio)
+  - TVCapture (848) w/Philips tuner FI12X6
+  - TVCapture (848) non-Philips tuner
+  - TVCapture98 (Bt878)
+  - TVPhone98 (Bt878)
+  - AVerTV und TVCapture98 w/VCR (Bt 878)
+  - AVerTVStudio und TVPhone98 w/VCR (Bt878)
+  - AVerTV GO Serie (Kein SVideo Input)
+  - AVerTV98 (BT-878 chip)
+  - AVerTV98 mit Fernbedienung (BT-878 chip)
+  - AVerTV/FM98 (BT-878 chip)
+
+  - VDOmate (www.averm.com.cn) = M168U ?
+
+Aimslab
+~~~~~~~
+
+Models:
+
+- Video Highway or "Video Highway TR200" (ISA)
+- Video Highway Xtreme (aka "VHX") (Bt848, FM w/ TEA5757)
+
+IXMicro (former: IMS=Integrated Micro Solutions)
+~~~~~~~
+
+Models:
+
+- IXTV BT848 (=TurboTV)
+- IXTV BT878
+- IMS TurboTV (Bt848)
+
+Lifetec/Medion/Tevion/Aldi
+~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- LT9306/MD9306 = CPH061
+- LT9415/MD9415 = LR90 Rev.F or Rev.G
+- MD9592 = Avermedia TVphone98 (PCI_ID=1461:0003), PCB-Rev=M168II-B (w/TDA9873H)
+- MD9717 = KNC One (Rev D4, saa7134, FM1216 MK2 tuner)
+- MD5044 = KNC One (Rev D4, saa7134, FM1216ME MK3 tuner)
+
+Modular Technologies (www.modulartech.com) UK
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- MM100 PCTV (Bt848)
+- MM201 PCTV (Bt878, Bt832) w/ Quartzsight camera
+- MM202 PCTV (Bt878, Bt832, tda9874)
+- MM205 PCTV (Bt878)
+- MM210 PCTV (Bt878) (Galaxy TV, Galaxymedia ?)
+
+Terratec
+~~~~~~~~
+
+Models:
+
+- Terra TV+ Version 1.0 (Bt848), "ceb105.PCB" printed on the PCB, TDA9821
+- Terra TV+ Version 1.1 (Bt878), "LR74 Rev.E" printed on the PCB, TDA9821
+- Terra TValueRadio,             "LR102 Rev.C" printed on the PCB
+- Terra TV/Radio+ Version 1.0,   "80-CP2830100-0" TTTV3 printed on the PCB,
+  "CPH010-E83" on the back, SAA6588T, TDA9873H
+- Terra TValue Version BT878,    "80-CP2830110-0 TTTV4" printed on the PCB,
+  "CPH011-D83" on back
+- Terra TValue Version 1.0       "ceb105.PCB" (really identical to Terra TV+ Version 1.0)
+- Terra TValue New Revision	  "LR102 Rec.C"
+- Terra Active Radio Upgrade (tea5757h, saa6588t)
+
+- LR74 is a newer PCB revision of ceb105 (both incl. connector for Active Radio Upgrade)
+
+- Cinergy 400 (saa7134), "E877 11(S)", "PM820092D" printed on PCB
+- Cinergy 600 (saa7134)
+
+Technisat
+~~~~~~~~~
+
+Models:
+
+- Discos ADR PC-Karte ISA (no TV!)
+- Discos ADR PC-Karte PCI (probably no TV?)
+- Techni-PC-Sat (Sat. analog)
+  Rev 1.2 (zr36120, vpx3220, stv0030, saa5246, BSJE3-494A)
+- Mediafocus I (zr36120/zr36125, drp3510, Sat. analog + ADR Radio)
+- Mediafocus II (saa7146, Sat. analog)
+- SatADR Rev 2.1 (saa7146a, saa7113h, stv0056a, msp3400c, drp3510a, BSKE3-307A)
+- SkyStar 1 DVB  (AV7110) = Technotrend Premium
+- SkyStar 2 DVB  (B2C2) (=Sky2PC)
+
+Siemens
+~~~~~~~
+
+Multimedia eXtension Board (MXB) (SAA7146, SAA7111)
+
+Powercolor
+~~~~~~~~~~
+
+Models:
+
+- MTV878
+       Package comes with different contents:
+           a) pcb "MTV878" (CARD=75)
+           b) Pixelview Rev. 4_
+- MTV878R w/Remote Control
+- MTV878F w/Remote Control w/FM radio
+
+Pinnacle
+~~~~~~~~
+
+PCTV models:
+
+- Mirovideo PCTV (Bt848)
+- Mirovideo PCTV SE (Bt848)
+- Mirovideo PCTV Pro (Bt848 + Daughterboard for TV Stereo and FM)
+- Studio PCTV Rave (Bt848 Version = Mirovideo PCTV)
+- Studio PCTV Rave (Bt878 package w/o infrared)
+- Studio PCTV      (Bt878)
+- Studio PCTV Pro  (Bt878 stereo w/ FM)
+- Pinnacle PCTV    (Bt878, MT2032)
+- Pinnacle PCTV Pro (Bt878, MT2032)
+- Pinncale PCTV Sat (bt878a, HM1821/1221) ["Conexant CX24110 with CX24108 tuner, aka HM1221/HM1811"]
+- Pinnacle PCTV Sat XE
+
+M(J)PEG capture and playback models:
+
+- DC1+ (ISA)
+- DC10  (zr36057,     zr36060,      saa7110, adv7176)
+- DC10+ (zr36067,     zr36060,      saa7110, adv7176)
+- DC20  (ql16x24b,zr36050, zr36016, saa7110, saa7187 ...)
+- DC30  (zr36057, zr36050, zr36016, vpx3220, adv7176, ad1843, tea6415, miro FST97A1)
+- DC30+ (zr36067, zr36050, zr36016, vpx3220, adv7176)
+- DC50  (zr36067, zr36050, zr36016, saa7112, adv7176 (2 pcs.?), ad1843, miro FST97A1, Lattice ???)
+
+Lenco
+~~~~~
+
+Models:
+
+- MXR-9565 (=Technisat Mediafocus?)
+- MXR-9571 (Bt848) (=CPH031?)
+- MXR-9575
+- MXR-9577 (Bt878) (=Prolink 878TV Rev.3x)
+- MXTV-9578CP (Bt878) (= Prolink PV-BT878P+4E)
+
+Iomega
+~~~~~~
+
+Buz (zr36067, zr36060, saa7111, saa7185)
+
+LML
+~~~
+   LML33 (zr36067, zr36060, bt819, bt856)
+
+Grandtec
+~~~~~~~~
+
+Models:
+
+- Grand Video Capture (Bt848)
+- Multi Capture Card  (Bt878)
+
+Koutech
+~~~~~~~
+
+Models:
+
+- KW-606 (Bt848)
+- KW-607 (Bt848 capture only)
+- KW-606RSF
+- KW-607A (capture only)
+- KW-608 (Zoran capture only)
+
+IODATA (jp)
+~~~~~~~~~~~
+
+Models:
+
+- GV-BCTV/PCI
+- GV-BCTV2/PCI
+- GV-BCTV3/PCI
+- GV-BCTV4/PCI
+- GV-VCP/PCI (capture only)
+- GV-VCP2/PCI (capture only)
+
+Canopus (jp)
+~~~~~~~~~~~~
+
+WinDVR	= Kworld "KW-TVL878RF"
+
+www.sigmacom.co.kr
+~~~~~~~~~~~~~~~~~~
+
+Sigma Cyber TV II
+
+www.sasem.co.kr
+~~~~~~~~~~~~~~~
+
+Litte OnAir TV
+
+hama
+~~~~
+
+TV/Radio-Tuner Card, PCI (Model 44677) = CPH051
+
+Sigma Designs
+~~~~~~~~~~~~~
+
+Hollywood plus (em8300, em9010, adv7175), (PCB "M340-10") MPEG DVD decoder
+
+Formac
+~~~~~~
+
+Models:
+
+- iProTV (Card for iMac Mezzanine slot, Bt848+SCSI)
+- ProTV (Bt848)
+- ProTV II = ProTV Stereo (Bt878) ["stereo" means FM stereo, tv is still mono]
+
+ATI
+~~~
+
+Models:
+
+- TV-Wonder
+- TV-Wonder VE
+
+Diamond Multimedia
+~~~~~~~~~~~~~~~~~~
+
+DTV2000 (Bt848, tda9875)
+
+Aopen
+~~~~~
+
+- VA1000 Plus (w/ Stereo)
+- VA1000 Lite
+- VA1000 (=LR90)
+
+Intel
+~~~~~
+
+Models:
+
+- Smart Video Recorder (ISA full-length)
+- Smart Video Recorder pro (ISA half-length)
+- Smart Video Recorder III (Bt848)
+
+STB
+~~~
+
+Models:
+
+- STB Gateway 6000704 (bt878)
+- STB Gateway 6000699 (bt848)
+- STB Gateway 6000402 (bt848)
+- STB TV130 PCI
+
+Videologic
+~~~~~~~~~~
+
+Models:
+
+- Captivator Pro/TV (ISA?)
+- Captivator PCI/VC (Bt848 bundled with camera) (capture only)
+
+Technotrend
+~~~~~~~~~~~~
+
+Models:
+
+- TT-SAT PCI (PCB "Sat-PCI Rev.:1.3.1"; zr36125, vpx3225d, stc0056a, Tuner:BSKE6-155A
+- TT-DVB-Sat
+   - revisions 1.1, 1.3, 1.5, 1.6 and 2.1
+   - This card is sold as OEM from:
+	- Siemens DVB-s Card
+	- Hauppauge WinTV DVB-S
+	- Technisat SkyStar 1 DVB
+	- Galaxis DVB Sat
+   - Now this card is called TT-PCline Premium Family
+   - TT-Budget (saa7146, bsru6-701a)
+    This card is sold as OEM from:
+	- Hauppauge WinTV Nova
+	- Satelco Standard PCI (DVB-S)
+   - TT-DVB-C PCI
+
+Teles
+~~~~~
+
+ DVB-s (Rev. 2.2, BSRV2-301A, data only?)
+
+Remote Vision
+~~~~~~~~~~~~~
+
+MX RV605 (Bt848 capture only)
+
+Boeder
+~~~~~~
+
+Models:
+
+- PC ChatCam (Model 68252) (Bt848 capture only)
+- Tv/Fm Capture Card  (Model 68404) = PV951
+
+Media-Surfer  (esc-kathrein.de)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- Sat-Surfer (ISA)
+- Sat-Surfer PCI = Techni-PC-Sat
+- Cable-Surfer 1
+- Cable-Surfer 2
+- Cable-Surfer PCI (zr36120)
+- Audio-Surfer (ISA Radio card)
+
+Jetway (www.jetway.com.tw)
+~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- JW-TV 878M
+- JW-TV 878  = KWorld KW-TV878RF
+
+Galaxis
+~~~~~~~
+
+Models:
+
+- Galaxis DVB Card S CI
+- Galaxis DVB Card C CI
+- Galaxis DVB Card S
+- Galaxis DVB Card C
+- Galaxis plug.in S [neuer Name: Galaxis DVB Card S CI
+
+Hauppauge
+~~~~~~~~~
+
+Models:
+
+- many many WinTV models ...
+- WinTV DVBs = Technotrend Premium 1.3
+- WinTV NOVA = Technotrend Budget 1.1 "S-DVB DATA"
+- WinTV NOVA-CI "SDVBACI"
+- WinTV Nova USB (=Technotrend USB 1.0)
+- WinTV-Nexus-s (=Technotrend Premium 2.1 or 2.2)
+- WinTV PVR
+- WinTV PVR 250
+- WinTV PVR 450
+
+US models
+
+-990 WinTV-PVR-350 (249USD) (iTVC15 chipset + radio)
+-980 WinTV-PVR-250 (149USD) (iTVC15 chipset)
+-880 WinTV-PVR-PCI (199USD) (KFIR chipset + bt878)
+-881 WinTV-PVR-USB
+-190 WinTV-GO
+-191 WinTV-GO-FM
+-404 WinTV
+-401 WinTV-radio
+-495 WinTV-Theater
+-602 WinTV-USB
+-621 WinTV-USB-FM
+-600 USB-Live
+-698 WinTV-HD
+-697 WinTV-D
+-564 WinTV-Nexus-S
+
+Deutsche Modelle:
+
+-603 WinTV GO
+-719 WinTV Primio-FM
+-718 WinTV PCI-FM
+-497 WinTV Theater
+-569 WinTV USB
+-568 WinTV USB-FM
+-882 WinTV PVR
+-981 WinTV PVR 250
+-891 WinTV-PVR-USB
+-541 WinTV Nova
+-488 WinTV Nova-Ci
+-564 WinTV-Nexus-s
+-727 WinTV-DVB-c
+-545 Common Interface
+-898 WinTV-Nova-USB
+
+UK models:
+
+-607 WinTV Go
+-693,793 WinTV Primio FM
+-647,747 WinTV PCI FM
+-498 WinTV Theater
+-883 WinTV PVR
+-893 WinTV PVR USB  (Duplicate entry)
+-566 WinTV USB (UK)
+-573 WinTV USB FM
+-429 Impact VCB (bt848)
+-600 USB Live (Video-In 1x Comp, 1xSVHS)
+-542 WinTV Nova
+-717 WinTV DVB-S
+-909 Nova-t PCI
+-893 Nova-t USB   (Duplicate entry)
+-802 MyTV
+-804 MyView
+-809 MyVideo
+-872 MyTV2Go FM
+-546 WinTV Nova-S CI
+-543 WinTV Nova
+-907 Nova-S USB
+-908 Nova-T USB
+-717 WinTV Nexus-S
+-157 DEC3000-s Standalone + USB
+
+Spain:
+
+-685 WinTV-Go
+-690 WinTV-PrimioFM
+-416 WinTV-PCI Nicam Estereo
+-677 WinTV-PCI-FM
+-699 WinTV-Theater
+-683 WinTV-USB
+-678 WinTV-USB-FM
+-983 WinTV-PVR-250
+-883 WinTV-PVR-PCI
+-993 WinTV-PVR-350
+-893 WinTV-PVR-USB
+-728 WinTV-DVB-C PCI
+-832 MyTV2Go
+-869 MyTV2Go-FM
+-805 MyVideo (USB)
+
+
+Matrix-Vision
+~~~~~~~~~~~~~
+
+Models:
+
+- MATRIX-Vision MV-Delta
+- MATRIX-Vision MV-Delta 2
+- MVsigma-SLC (Bt848)
+
+Conceptronic (.net)
+~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- TVCON FM,  TV card w/ FM = CPH05x
+- TVCON = CPH06x
+
+BestData
+~~~~~~~~
+
+Models:
+
+- HCC100 = VCC100rev1 + camera
+- VCC100 rev1 (bt848)
+- VCC100 rev2 (bt878)
+
+Gallant  (www.gallantcom.com) www.minton.com.tw
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- Intervision IV-510 (capture only bt8x8)
+- Intervision IV-550 (bt8x8)
+- Intervision IV-100 (zoran)
+- Intervision IV-1000 (bt8x8)
+
+Asonic (www.asonic.com.cn) (website down)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+SkyEye tv 878
+
+Hoontech
+~~~~~~~~
+
+878TV/FM
+
+Teppro (www.itcteppro.com.tw)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- ITC PCITV (Card Ver 1.0) "Teppro TV1/TVFM1 Card"
+- ITC PCITV (Card Ver 2.0)
+- ITC PCITV (Card Ver 3.0) = "PV-BT878P+ (REV.9D)"
+- ITC PCITV (Card Ver 4.0)
+- TEPPRO IV-550 (For BT848 Main Chip)
+- ITC DSTTV (bt878, satellite)
+- ITC VideoMaker (saa7146, StreamMachine sm2110, tvtuner) "PV-SM2210P+ (REV:1C)"
+
+Kworld (www.kworld.com.tw)
+~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+PC TV Station:
+
+- KWORLD KW-TV878R  TV (no radio)
+- KWORLD KW-TV878RF TV (w/ radio)
+- KWORLD KW-TVL878RF (low profile)
+- KWORLD KW-TV713XRF (saa7134)
+
+
+ MPEG TV Station (same cards as above plus WinDVR Software MPEG en/decoder)
+
+- KWORLD KW-TV878R -Pro   TV (no Radio)
+- KWORLD KW-TV878RF-Pro   TV (w/ Radio)
+- KWORLD KW-TV878R -Ultra TV (no Radio)
+- KWORLD KW-TV878RF-Ultra TV (w/ Radio)
+
+JTT/ Justy Corp.(http://www.jtt.ne.jp/)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+JTT-02 (JTT TV) "TV watchmate pro" (bt848)
+
+ADS www.adstech.com
+~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- Channel Surfer TV ( CHX-950 )
+- Channel Surfer TV+FM ( CHX-960FM )
+
+AVEC www.prochips.com
+~~~~~~~~~~~~~~~~~~~~~
+
+AVEC Intercapture (bt848, tea6320)
+
+NoBrand
+~~~~~~~
+
+TV Excel = Australian Name for "PV-BT878P+ 8E" or "878TV Rev.3_"
+
+Mach www.machspeed.com
+~~~~~~~~~~~~~~~~~~~~~~
+
+Mach TV 878
+
+Eline www.eline-net.com/
+~~~~~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- Eline Vision TVMaster / TVMaster FM (ELV-TVM/ ELV-TVM-FM) = LR26  (bt878)
+- Eline Vision TVMaster-2000 (ELV-TVM-2000, ELV-TVM-2000-FM)= LR138 (saa713x)
+
+Spirit
+~~~~~~
+
+- Spirit TV Tuner/Video Capture Card (bt848)
+
+Boser www.boser.com.tw
+~~~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- HS-878 Mini PCI Capture Add-on Card
+- HS-879 Mini PCI 3D Audio and Capture Add-on Card (w/ ES1938 Solo-1)
+
+Satelco www.citycom-gmbh.de, www.satelco.de
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- TV-FM =KNC1 saa7134
+- Standard PCI (DVB-S) = Technotrend Budget
+- Standard PCI (DVB-S) w/ CI
+- Satelco Highend PCI (DVB-S) = Technotrend Premium
+
+
+Sensoray www.sensoray.com
+~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- Sensoray 311 (PC/104 bus)
+- Sensoray 611 (PCI)
+
+CEI (Chartered Electronics Industries Pte Ltd [CEI] [FCC ID HBY])
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- TV Tuner  -  HBY-33A-RAFFLES  Brooktree Bt848KPF + Philips
+- TV Tuner MG9910  -  HBY33A-TVO  CEI + Philips SAA7110 + OKI M548262 + ST STV8438CV
+- Primetime TV (ISA)
+  - acquired by Singapore Technologies
+  - now operating as Chartered Semiconductor Manufacturing
+  - Manufacturer of video cards is listed as:
+    - Cogent Electronics Industries [CEI]
+
+AITech
+~~~~~~
+
+Models:
+
+- Wavewatcher TV (ISA)
+- AITech WaveWatcher TV-PCI = can be LR26 (Bt848) or LR50 (BT878)
+- WaveWatcher TVR-202 TV/FM Radio Card (ISA)
+
+MAXRON
+~~~~~~
+
+Maxron MaxTV/FM Radio (KW-TV878-FNT) = Kworld or JW-TV878-FBK
+
+www.ids-imaging.de
+~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- Falcon Series (capture only)
+ In USA: http://www.theimagingsource.com/
+- DFG/LC1
+
+www.sknet-web.co.jp
+~~~~~~~~~~~~~~~~~~~
+
+SKnet Monster TV (saa7134)
+
+A-Max www.amaxhk.com (Colormax, Amax, Napa)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+APAC Viewcomp 878
+
+Cybertainment
+~~~~~~~~~~~~~
+
+Models:
+
+- CyberMail AV Video Email Kit w/ PCI Capture Card (capture only)
+- CyberMail Xtreme
+
+These are Flyvideo
+
+VCR (http://www.vcrinc.com/)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Video Catcher 16
+
+Twinhan
+~~~~~~~
+
+Models:
+
+- DST Card/DST-IP (bt878, twinhan asic) VP-1020
+  - Sold as:
+    - KWorld DVBS Satellite TV-Card
+    - Powercolor DSTV Satellite Tuner Card
+    - Prolink Pixelview DTV2000
+    - Provideo PV-911 Digital Satellite TV Tuner Card With Common Interface ?
+- DST-CI Card (DVB Satellite) VP-1030
+- DCT Card (DVB cable)
+
+MSI
+~~~
+
+Models:
+
+- MSI TV@nywhere Tuner Card (MS-8876) (CX23881/883) Not Bt878 compatible.
+- MS-8401 DVB-S
+
+Focus www.focusinfo.com
+~~~~~~~~~~~~~~~~~~~~~~~
+
+InVideo PCI (bt878)
+
+Sdisilk www.sdisilk.com/
+~~~~~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- SDI Silk 100
+- SDI Silk 200 SDI Input Card
+
+www.euresys.com
+~~~~~~~~~~~~~~~
+
+PICOLO series
+
+PMC/Pace
+~~~~~~~~
+
+www.pacecom.co.uk website closed
+
+Mercury www.kobian.com (UK and FR)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- LR50
+- LR138RBG-Rx  == LR138
+
+TEC sound
+~~~~~~~~~
+
+TV-Mate = Zoltrix VP-8482
+
+Though educated googling found: www.techmakers.com
+
+(package and manuals don't have any other manufacturer info) TecSound
+
+Lorenzen www.lorenzen.de
+~~~~~~~~~~~~~~~~~~~~~~~~
+
+SL DVB-S PCI = Technotrend Budget PCI (su1278 or bsru version)
+
+Origo (.uk) www.origo2000.com
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+PC TV Card = LR50
+
+I/O Magic www.iomagic.com
+~~~~~~~~~~~~~~~~~~~~~~~~~
+
+PC PVR - Desktop TV Personal Video Recorder DR-PCTV100 = Pinnacle ROB2D-51009464 4.0 + Cyberlink PowerVCR II
+
+Arowana
+~~~~~~~
+
+TV-Karte / Poso Power TV (?) = Zoltrix VP-8482 (?)
+
+iTVC15 boards:
+~~~~~~~~~~~~~
+
+kuroutoshikou.com ITVC15
+yuan.com MPG160 PCI TV (Internal PCI MPEG2 encoder card plus TV-tuner)
+
+Asus www.asuscom.com
+~~~~~~~~~~~~~~~~~~~~
+
+Models:
+
+- Asus TV Tuner Card 880 NTSC (low profile, cx23880)
+- Asus TV (saa7134)
+
+Hoontech
+~~~~~~~~
+
+http://www.hoontech.de/
+
+- HART Vision 848 (H-ART Vision 848)
+- HART Vision 878 (H-Art Vision 878)
+
+
+
+Chips used at bttv devices
+--------------------------
+
+- all boards:
+
+  - Brooktree Bt848/848A/849/878/879: video capture chip
+
+- Board specific
+
+  - Miro PCTV:
+
+    - Philips or Temic Tuner
+
+  - Hauppauge Win/TV pci (version 405):
+
+    - Microchip 24LC02B or Philips 8582E2Y:
+       - 256 Byte EEPROM with configuration information
+       - I2C 0xa0-0xa1, (24LC02B also responds to 0xa2-0xaf)
+    - Philips SAA5246AGP/E: Videotext decoder chip, I2C 0x22-0x23
+
+    - TDA9800: sound decoder
+
+    - Winbond W24257AS-35: 32Kx8 CMOS static RAM (Videotext buffer mem)
+
+    - 14052B: analog switch for selection of sound source
+
+- PAL:
+
+  - TDA5737: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners
+  - TSA5522: 1.4 GHz I2C-bus controlled synthesizer, I2C 0xc2-0xc3
+
+- NTSC:
+
+  - TDA5731: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners
+  - TSA5518: no datasheet available on Philips site
+
+- STB TV pci:
+
+  - ???
+  - if you want better support for STB cards send me info!
+    Look at the board! What chips are on it?
+
+
+
+
+Specs
+-----
+Philips		http://www.Semiconductors.COM/pip/
+Conexant	http://www.conexant.com/
+Micronas	http://www.micronas.com/en/home/index.html
+
+Thanks
+------
+
+Many thanks to:
+
+- Markus Schroeder <schroedm@uni-duesseldorf.de> for information on the Bt848
+  and tuner programming and his control program xtvc.
+
+- Martin Buck <martin-2.buck@student.uni-ulm.de> for his great Videotext
+  package.
+
+- Gerd Hoffmann for the MSP3400 support and the modular
+  I2C, tuner, ... support.
+
+
+- MATRIX Vision for giving us 2 cards for free, which made support of
+  single crystal operation possible.
+
+- MIRO for providing a free PCTV card and detailed information about the
+  components on their cards. (E.g. how the tuner type is detected)
+  Without their card I could not have debugged the NTSC mode.
+
+- Hauppauge for telling how the sound input is selected and what components
+  they do and will use on their radio cards.
+  Also many thanks for faxing me the FM1216 data sheet.
+
+Contributors
+------------
+
+Michael Chu <mmchu@pobox.com>
+  AverMedia fix and more flexible card recognition
+
+Alan Cox <alan@lxorguk.ukuu.org.uk>
+  Video4Linux interface and 2.1.x kernel adaptation
+
+Chris Kleitsch
+  Hardware I2C
+
+Gerd Hoffmann
+  Radio card (ITT sound processor)
+
+bigfoot <bigfoot@net-way.net>
+Ragnar Hojland Espinosa <ragnar@macula.net>
+  ConferenceTV card
+
+
++ many more (please mail me if you are missing in this list and would
+	     like to be mentioned)
diff --git a/Documentation/video4linux/bttv/Tuners b/Documentation/media/v4l-drivers/tuners.rst
index 0a371d349542..0a371d349542 100644
--- a/Documentation/video4linux/bttv/Tuners
+++ b/Documentation/media/v4l-drivers/tuners.rst
diff --git a/Documentation/video4linux/bttv/CONTRIBUTORS b/Documentation/video4linux/bttv/CONTRIBUTORS
deleted file mode 100644
index eb41b2650860..000000000000
--- a/Documentation/video4linux/bttv/CONTRIBUTORS
+++ /dev/null
@@ -1,25 +0,0 @@
-Contributors to bttv:
-
-Michael Chu <mmchu@pobox.com>
-  AverMedia fix and more flexible card recognition
-
-Alan Cox <alan@lxorguk.ukuu.org.uk>
-  Video4Linux interface and 2.1.x kernel adaptation
-
-Chris Kleitsch
-  Hardware I2C
-
-Gerd Knorr <kraxel@cs.tu-berlin.de>
-  Radio card (ITT sound processor)
-
-bigfoot <bigfoot@net-way.net>
-Ragnar Hojland Espinosa <ragnar@macula.net>
-  ConferenceTV card
-
-
-+ many more (please mail me if you are missing in this list and would
-	     like to be mentioned)
-
-
-
-
diff --git a/Documentation/video4linux/bttv/Cards b/Documentation/video4linux/bttv/Cards
deleted file mode 100644
index a8fb6e2d3c8b..000000000000
--- a/Documentation/video4linux/bttv/Cards
+++ /dev/null
@@ -1,960 +0,0 @@
-
-Gunther Mayer's bttv card gallery (graphical version of this text file :-)
-is available at: http://www.bttv-gallery.de/
-
-
-Supported cards:
-Bt848/Bt848a/Bt849/Bt878/Bt879 cards
-------------------------------------
-
-All cards with Bt848/Bt848a/Bt849/Bt878/Bt879 and normal
-Composite/S-VHS inputs are supported.  Teletext and Intercast support
-(PAL only) for ALL cards via VBI sample decoding in software.
-
-Some cards with additional multiplexing of inputs or other additional
-fancy chips are only partially supported (unless specifications by the
-card manufacturer are given).  When a card is listed here it isn't
-necessarily fully supported.
-
-All other cards only differ by additional components as tuners, sound
-decoders, EEPROMs, teletext decoders ...
-
-
-Unsupported Cards:
-------------------
-
-Cards with Zoran (ZR) or Philips (SAA) or ISA are not supported by
-this driver.
-
-
-MATRIX Vision
--------------
-
-MV-Delta
-- Bt848A
-- 4 Composite inputs, 1 S-VHS input (shared with 4th composite)
-- EEPROM
-
-http://www.matrix-vision.de/
-
-This card has no tuner but supports all 4 composite (1 shared with an
-S-VHS input) of the Bt848A.
-Very nice card if you only have satellite TV but several tuners connected
-to the card via composite.
-
-Many thanks to Matrix-Vision for giving us 2 cards for free which made
-Bt848a/Bt849 single crystal operation support possible!!!
-
-
-
-Miro/Pinnacle PCTV
-------------------
-
-- Bt848
-  some (all??) come with 2 crystals for PAL/SECAM and NTSC
-- PAL, SECAM or NTSC TV tuner (Philips or TEMIC)
-- MSP34xx sound decoder on add on board
-  decoder is supported but AFAIK does not yet work
-  (other sound MUX setting in GPIO port needed??? somebody who fixed this???)
-- 1 tuner, 1 composite and 1 S-VHS input
-- tuner type is autodetected
-
-http://www.miro.de/
-http://www.miro.com/
-
-
-Many thanks for the free card which made first NTSC support possible back
-in 1997!
-
-
-Hauppauge Win/TV pci
---------------------
-
-There are many different versions of the Hauppauge cards with different
-tuners (TV+Radio ...), teletext decoders.
-Note that even cards with same model numbers have (depending on the revision)
-different chips on it.
-
-- Bt848 (and others but always in 2 crystal operation???)
-  newer cards have a Bt878
-- PAL, SECAM, NTSC or tuner with or without Radio support
-
-e.g.:
-  PAL:
-  TDA5737: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners
-  TSA5522: 1.4 GHz I2C-bus controlled synthesizer, I2C 0xc2-0xc3
-
-  NTSC:
-  TDA5731: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners
-  TSA5518: no datasheet available on Philips site
-- Philips SAA5246 or SAA5284 ( or no) Teletext decoder chip
-  with buffer RAM (e.g. Winbond W24257AS-35: 32Kx8 CMOS static RAM)
-  SAA5246 (I2C 0x22) is supported
-- 256 bytes EEPROM: Microchip 24LC02B or Philips 8582E2Y
-  with configuration information
-  I2C address 0xa0 (24LC02B also responds to 0xa2-0xaf)
-- 1 tuner, 1 composite and (depending on model) 1 S-VHS input
-- 14052B: mux for selection of sound source
-- sound decoder: TDA9800, MSP34xx (stereo cards)
-
-
-Askey CPH-Series
-----------------
-Developed by TelSignal(?), OEMed by many vendors (Typhoon, Anubis, Dynalink)
-
-  Card series:
-    CPH01x: BT848 capture only
-    CPH03x: BT848
-    CPH05x: BT878 with FM
-    CPH06x: BT878 (w/o FM)
-    CPH07x: BT878 capture only
-
-  TV standards:
-     CPH0x0: NTSC-M/M
-     CPH0x1: PAL-B/G
-     CPH0x2: PAL-I/I
-     CPH0x3: PAL-D/K
-     CPH0x4: SECAM-L/L
-     CPH0x5: SECAM-B/G
-     CPH0x6: SECAM-D/K
-     CPH0x7: PAL-N/N
-     CPH0x8: PAL-B/H
-     CPH0x9: PAL-M/M
-
-  CPH03x was often sold as "TV capturer".
-
-  Identifying:
-  1) 878 cards can be identified by PCI Subsystem-ID:
-      144f:3000 = CPH06x
-      144F:3002 = CPH05x w/ FM
-      144F:3005 = CPH06x_LC (w/o remote control)
-  1) The cards have a sticker with "CPH"-model on the back.
-  2) These cards have a number printed on the PCB just above the tuner metal box:
-      "80-CP2000300-x" = CPH03X
-      "80-CP2000500-x" = CPH05X
-      "80-CP2000600-x" = CPH06X / CPH06x_LC
-
-  Askey sells these cards as "Magic TView series", Brand "MagicXpress".
-  Other OEM often call these "Tview", "TView99" or else.
-
-Lifeview Flyvideo Series:
--------------------------
-  The naming of these series differs in time and space.
-
-  Identifying:
-  1) Some models can be identified by PCI subsystem ID:
-      1852:1852 = Flyvideo 98 FM
-      1851:1850 = Flyvideo 98
-      1851:1851 = Flyvideo 98 EZ (capture only)
-  2) There is a print on the PCB:
-      LR25       = Flyvideo (Zoran ZR36120, SAA7110A)
-      LR26 Rev.N = Flyvideo II (Bt848)
-	   Rev.O = Flyvideo II (Bt878)
-      LR37 Rev.C = Flyvideo EZ (Capture only, ZR36120 + SAA7110)
-      LR38 Rev.A1= Flyvideo II EZ (Bt848 capture only)
-      LR50 Rev.Q = Flyvideo 98 (w/eeprom and PCI subsystem ID)
-	   Rev.W = Flyvideo 98 (no eeprom)
-      LR51 Rev.E = Flyvideo 98 EZ (capture only)
-      LR90       = Flyvideo 2000 (Bt878)
-		   Flyvideo 2000S (Bt878) w/Stereo TV (Package incl. LR91 daughterboard)
-      LR91       = Stereo daughter card for LR90
-      LR97       = Flyvideo DVBS
-      LR99 Rev.E = Low profile card for OEM integration (only internal audio!) bt878
-      LR136	 = Flyvideo 2100/3100 (Low profile, SAA7130/SAA7134)
-      LR137      = Flyvideo DV2000/DV3000 (SAA7130/SAA7134 + IEEE1394)
-      LR138 Rev.C= Flyvideo 2000 (SAA7130)
-		or Flyvideo 3000 (SAA7134) w/Stereo TV
-		   These exist in variations w/FM and w/Remote sometimes denoted
-		   by suffixes "FM" and "R".
-  3) You have a laptop (miniPCI card):
-      Product    = FlyTV Platinum Mini
-      Model/Chip = LR212/saa7135
-
-      Lifeview.com.tw states (Feb. 2002):
-      "The FlyVideo2000 and FlyVideo2000s product name have renamed to FlyVideo98."
-      Their Bt8x8 cards are listed as discontinued.
-      Flyvideo 2000S was probably sold as Flyvideo 3000 in some contries(Europe?).
-      The new Flyvideo 2000/3000 are SAA7130/SAA7134 based.
-
-  "Flyvideo II" had been the name for the 848 cards, nowadays (in Germany)
-  this name is re-used for LR50 Rev.W.
-  The Lifeview website mentioned Flyvideo III at some time, but such a card
-  has not yet been seen (perhaps it was the german name for LR90 [stereo]).
-  These cards are sold by many OEMs too.
-
-  FlyVideo A2 (Elta 8680)= LR90 Rev.F (w/Remote, w/o FM, stereo TV by tda9821) {Germany}
-  Lifeview 3000 (Elta 8681) as sold by Plus(April 2002), Germany = LR138 w/ saa7134
-
-
-Typhoon TV card series:
------------------------
-  These can be CPH, Flyvideo, Pixelview or KNC1 series.
-  Typhoon is the brand of Anubis.
-  Model 50680 got re-used, some model no. had different contents over time.
-
-  Models:
-  50680 "TV Tuner PCI Pal BG"(old,red package)=can be CPH03x(bt848) or CPH06x(bt878)
-  50680 "TV Tuner Pal BG" (blue package)= Pixelview PV-BT878P+ (Rev 9B)
-  50681 "TV Tuner PCI Pal I" (variant of 50680)
-  50682 "TView TV/FM Tuner Pal BG"       = Flyvideo 98FM (LR50 Rev.Q)
-	 Note: The package has a picture of CPH05x (which would be a real TView)
-  50683 "TV Tuner PCI SECAM" (variant of 50680)
-  50684 "TV Tuner Pal BG"                = Pixelview 878TV(Rev.3D)
-  50686 "TV Tuner"                       = KNC1 TV Station
-  50687 "TV Tuner stereo"                = KNC1 TV Station pro
-  50688 "TV Tuner RDS" (black package)   = KNC1 TV Station RDS
-  50689  TV SAT DVB-S CARD CI PCI (SAA7146AH, SU1278?) = "KNC1 TV Station DVB-S"
-  50692 "TV/FM Tuner" (small PCB)
-  50694  TV TUNER CARD RDS (PHILIPS CHIPSET SAA7134HL)
-  50696  TV TUNER STEREO (PHILIPS CHIPSET SAA7134HL, MK3ME Tuner)
-  50804  PC-SAT TV/Audio Karte = Techni-PC-Sat (ZORAN 36120PQC, Tuner:Alps)
-  50866  TVIEW SAT RECEIVER+ADR
-  50868 "TV/FM Tuner Pal I" (variant of 50682)
-  50999 "TV/FM Tuner Secam" (variant of 50682)
-
-
-Guillemot
----------
-  Maxi-TV PCI (ZR36120)
-  Maxi TV Video 2 = LR50 Rev.Q (FI1216MF, PAL BG+SECAM)
-  Maxi TV Video 3 = CPH064 (PAL BG + SECAM)
-
-Mentor
-------
-  Mentor TV card ("55-878TV-U1") = Pixelview 878TV(Rev.3F) (w/FM w/Remote)
-
-Prolink
--------
-   TV cards:
-   PixelView Play TV pro - (Model: PV-BT878P+ REV 8E)
-   PixelView Play TV pro - (Model: PV-BT878P+ REV 9D)
-   PixelView Play TV pro - (Model: PV-BT878P+ REV 4C / 8D / 10A )
-   PixelView Play TV - (Model: PV-BT848P+)
-   878TV - (Model: PV-BT878TV)
-
-   Multimedia TV packages (card + software pack):
-   PixelView Play TV Theater - (Model: PV-M4200) =  PixelView Play TV pro + Software
-   PixelView Play TV PAK -     (Model: PV-BT878P+ REV 4E)
-   PixelView Play TV/VCR -     (Model: PV-M3200 REV 4C / 8D / 10A )
-   PixelView Studio PAK -      (Model:    M2200 REV 4C / 8D / 10A )
-   PixelView PowerStudio PAK - (Model: PV-M3600 REV 4E)
-   PixelView DigitalVCR PAK -  (Model: PV-M2400 REV 4C / 8D / 10A )
-
-   PixelView PlayTV PAK II (TV/FM card + usb camera)  PV-M3800
-   PixelView PlayTV XP PV-M4700,PV-M4700(w/FM)
-   PixelView PlayTV DVR PV-M4600  package contents:PixelView PlayTV pro, windvr & videoMail s/w
-
-   Further Cards:
-   PV-BT878P+rev.9B (Play TV Pro, opt. w/FM w/NICAM)
-   PV-BT878P+rev.2F
-   PV-BT878P Rev.1D (bt878, capture only)
-
-   XCapture PV-CX881P (cx23881)
-   PlayTV HD PV-CX881PL+, PV-CX881PL+(w/FM) (cx23881)
-
-   DTV3000 PV-DTV3000P+ DVB-S CI = Twinhan VP-1030
-   DTV2000 DVB-S = Twinhan VP-1020
-
-   Video Conferencing:
-   PixelView Meeting PAK - (Model: PV-BT878P)
-   PixelView Meeting PAK Lite - (Model: PV-BT878P)
-   PixelView Meeting PAK plus - (Model: PV-BT878P+rev 4C/8D/10A)
-   PixelView Capture - (Model: PV-BT848P)
-
-   PixelView PlayTV USB pro
-   Model No. PV-NT1004+, PV-NT1004+ (w/FM) = NT1004 USB decoder chip + SAA7113 video decoder chip
-
-Dynalink
---------
-   These are CPH series.
-
-Phoebemicro
------------
-   TV Master    = CPH030 or CPH060
-   TV Master FM = CPH050
-
-Genius/Kye
-----------
-   Video Wonder/Genius Internet Video Kit = LR37 Rev.C
-   Video Wonder Pro II (848 or 878) = LR26
-
-Tekram
-------
-   VideoCap C205 (Bt848)
-   VideoCap C210 (zr36120 +Philips)
-   CaptureTV M200 (ISA)
-   CaptureTV M205 (Bt848)
-
-Lucky Star
-----------
-   Image World Conference TV = LR50 Rev. Q
-
-Leadtek
--------
-   WinView 601 (Bt848)
-   WinView 610 (Zoran)
-   WinFast2000
-   WinFast2000 XP
-
-KNC One
--------
-   TV-Station
-   TV-Station SE (+Software Bundle)
-   TV-Station pro (+TV stereo)
-   TV-Station FM (+Radio)
-   TV-Station RDS (+RDS)
-   TV Station SAT (analog satellite)
-   TV-Station DVB-S
-
-   newer Cards have saa7134, but model name stayed the same?
-
-Provideo
---------
-  PV951 or PV-951 (also are sold as:
-   Boeder TV-FM Video Capture Card
-   Titanmedia Supervision TV-2400
-   Provideo PV951 TF
-   3DeMon PV951
-   MediaForte TV-Vision PV951
-   Yoko PV951
-   Vivanco Tuner Card PCI Art.-Nr.: 68404
-  ) now named PV-951T
-
-  Surveillance Series
-  PV-141
-  PV-143
-  PV-147
-  PV-148 (capture only)
-  PV-150
-  PV-151
-
-  TV-FM Tuner Series
-  PV-951TDV (tv tuner + 1394)
-  PV-951T/TF
-  PV-951PT/TF
-  PV-956T/TF Low Profile
-  PV-911
-
-Highscreen
-----------
-   TV Karte = LR50 Rev.S
-   TV-Boostar = Terratec Terra TV+ Version 1.0 (Bt848, tda9821) "ceb105.pcb"
-
-Zoltrix
--------
-   Face to Face Capture (Bt848 capture only) (PCB "VP-2848")
-   Face To Face TV MAX (Bt848) (PCB "VP-8482 Rev1.3")
-   Genie TV (Bt878) (PCB "VP-8790 Rev 2.1")
-   Genie Wonder Pro
-
-AVerMedia
----------
-   AVer FunTV Lite (ISA, AV3001 chipset)  "M101.C"
-   AVerTV
-   AVerTV Stereo
-   AVerTV Studio (w/FM)
-   AVerMedia TV98 with Remote
-   AVerMedia TV/FM98 Stereo
-   AVerMedia TVCAM98
-   TVCapture (Bt848)
-   TVPhone (Bt848)
-   TVCapture98 (="AVerMedia TV98" in USA) (Bt878)
-   TVPhone98 (Bt878, w/FM)
-
-   PCB      PCI-ID      Model-Name      Eeprom  Tuner  Sound    Country
-   --------------------------------------------------------------------
-   M101.C   ISA !
-   M108-B      Bt848                     --     FR1236		 US   (2),(3)
-   M1A8-A      Bt848    AVer TV-Phone           FM1216  --
-   M168-T   1461:0003   AVerTV Studio   48:17   FM1216 TDA9840T  D    (1) w/FM w/Remote
-   M168-U   1461:0004   TVCapture98     40:11   FI1216   --      D    w/Remote
-   M168II-B 1461:0003   Medion MD9592   48:16   FM1216 TDA9873H  D    w/FM
-
-   (1) Daughterboard MB68-A with TDA9820T and TDA9840T
-   (2) Sony NE41S soldered (stereo sound?)
-   (3) Daughterboard M118-A w/ pic 16c54 and 4 MHz quartz
-
-   US site has different drivers for (as of 09/2002):
-   EZ Capture/InterCam PCI (BT-848 chip)
-   EZ Capture/InterCam PCI (BT-878 chip)
-   TV-Phone (BT-848 chip)
-   TV98 (BT-848 chip)
-   TV98 With Remote (BT-848 chip)
-   TV98 (BT-878 chip)
-   TV98 With Remote (BT-878)
-   TV/FM98 (BT-878 chip)
-   AVerTV
-   AverTV Stereo
-   AVerTV Studio
-
-   DE hat diverse Treiber fuer diese Modelle (Stand 09/2002):
-   TVPhone (848) mit Philips tuner FR12X6 (w/ FM radio)
-   TVPhone (848) mit Philips tuner FM12X6 (w/ FM radio)
-   TVCapture (848) w/Philips tuner FI12X6
-   TVCapture (848) non-Philips tuner
-   TVCapture98 (Bt878)
-   TVPhone98 (Bt878)
-   AVerTV und TVCapture98 w/VCR (Bt 878)
-   AVerTVStudio und TVPhone98 w/VCR (Bt878)
-   AVerTV GO Serie (Kein SVideo Input)
-   AVerTV98 (BT-878 chip)
-   AVerTV98 mit Fernbedienung (BT-878 chip)
-   AVerTV/FM98 (BT-878 chip)
-
-   VDOmate (www.averm.com.cn) = M168U ?
-
-Aimslab
--------
-   Video Highway or "Video Highway TR200" (ISA)
-   Video Highway Xtreme (aka "VHX") (Bt848, FM w/ TEA5757)
-
-IXMicro (former: IMS=Integrated Micro Solutions)
--------
-   IXTV BT848 (=TurboTV)
-   IXTV BT878
-   IMS TurboTV (Bt848)
-
-Lifetec/Medion/Tevion/Aldi
---------------------------
-   LT9306/MD9306 = CPH061
-   LT9415/MD9415 = LR90 Rev.F or Rev.G
-	  MD9592 = Avermedia TVphone98 (PCI_ID=1461:0003), PCB-Rev=M168II-B (w/TDA9873H)
-	  MD9717 = KNC One (Rev D4, saa7134, FM1216 MK2 tuner)
-	  MD5044 = KNC One (Rev D4, saa7134, FM1216ME MK3 tuner)
-
-Modular Technologies (www.modulartech.com) UK
----------------------------------------------
-   MM100 PCTV (Bt848)
-   MM201 PCTV (Bt878, Bt832) w/ Quartzsight camera
-   MM202 PCTV (Bt878, Bt832, tda9874)
-   MM205 PCTV (Bt878)
-   MM210 PCTV (Bt878) (Galaxy TV, Galaxymedia ?)
-
-Terratec
---------
-   Terra TV+ Version 1.0 (Bt848), "ceb105.PCB" printed on the PCB, TDA9821
-   Terra TV+ Version 1.1 (Bt878), "LR74 Rev.E" printed on the PCB, TDA9821
-   Terra TValueRadio,             "LR102 Rev.C" printed on the PCB
-   Terra TV/Radio+ Version 1.0,   "80-CP2830100-0" TTTV3 printed on the PCB,
-				     "CPH010-E83" on the back, SAA6588T, TDA9873H
-   Terra TValue Version BT878,    "80-CP2830110-0 TTTV4" printed on the PCB,
-				     "CPH011-D83" on back
-   Terra TValue Version 1.0       "ceb105.PCB" (really identical to Terra TV+ Version 1.0)
-   Terra TValue New Revision	  "LR102 Rec.C"
-   Terra Active Radio Upgrade (tea5757h, saa6588t)
-
-   LR74 is a newer PCB revision of ceb105 (both incl. connector for Active Radio Upgrade)
-
-   Cinergy 400 (saa7134), "E877 11(S)", "PM820092D" printed on PCB
-   Cinergy 600 (saa7134)
-
-Technisat
----------
-   Discos ADR PC-Karte ISA (no TV!)
-   Discos ADR PC-Karte PCI (probably no TV?)
-   Techni-PC-Sat (Sat. analog)
-	 Rev 1.2 (zr36120, vpx3220, stv0030, saa5246, BSJE3-494A)
-   Mediafocus I (zr36120/zr36125, drp3510, Sat. analog + ADR Radio)
-   Mediafocus II (saa7146, Sat. analog)
-	 SatADR Rev 2.1 (saa7146a, saa7113h, stv0056a, msp3400c, drp3510a, BSKE3-307A)
-   SkyStar 1 DVB  (AV7110) = Technotrend Premium
-   SkyStar 2 DVB  (B2C2) (=Sky2PC)
-
-Siemens
--------
-   Multimedia eXtension Board (MXB) (SAA7146, SAA7111)
-
-Powercolor
-----------
-   MTV878
-       Package comes with different contents:
-       a) pcb "MTV878" (CARD=75)
-       b) Pixelview Rev. 4_
-   MTV878R w/Remote Control
-   MTV878F w/Remote Control w/FM radio
-
-Pinnacle
---------
-   Mirovideo PCTV (Bt848)
-   Mirovideo PCTV SE (Bt848)
-   Mirovideo PCTV Pro (Bt848 + Daughterboard for TV Stereo and FM)
-   Studio PCTV Rave (Bt848 Version = Mirovideo PCTV)
-   Studio PCTV Rave (Bt878 package w/o infrared)
-   Studio PCTV      (Bt878)
-   Studio PCTV Pro  (Bt878 stereo w/ FM)
-   Pinnacle PCTV    (Bt878, MT2032)
-   Pinnacle PCTV Pro (Bt878, MT2032)
-   Pinncale PCTV Sat (bt878a, HM1821/1221) ["Conexant CX24110 with CX24108 tuner, aka HM1221/HM1811"]
-   Pinnacle PCTV Sat XE
-
-   M(J)PEG capture and playback:
-   DC1+ (ISA)
-   DC10  (zr36057,     zr36060,      saa7110, adv7176)
-   DC10+ (zr36067,     zr36060,      saa7110, adv7176)
-   DC20  (ql16x24b,zr36050, zr36016, saa7110, saa7187 ...)
-   DC30  (zr36057, zr36050, zr36016, vpx3220, adv7176, ad1843, tea6415, miro FST97A1)
-   DC30+ (zr36067, zr36050, zr36016, vpx3220, adv7176)
-   DC50  (zr36067, zr36050, zr36016, saa7112, adv7176 (2 pcs.?), ad1843, miro FST97A1, Lattice ???)
-
-Lenco
------
-   MXR-9565 (=Technisat Mediafocus?)
-   MXR-9571 (Bt848) (=CPH031?)
-   MXR-9575
-   MXR-9577 (Bt878) (=Prolink 878TV Rev.3x)
-   MXTV-9578CP (Bt878) (= Prolink PV-BT878P+4E)
-
-Iomega
-------
-   Buz (zr36067, zr36060, saa7111, saa7185)
-
-LML
----
-   LML33 (zr36067, zr36060, bt819, bt856)
-
-Grandtec
---------
-   Grand Video Capture (Bt848)
-   Multi Capture Card  (Bt878)
-
-Koutech
--------
-   KW-606 (Bt848)
-   KW-607 (Bt848 capture only)
-   KW-606RSF
-   KW-607A (capture only)
-   KW-608 (Zoran capture only)
-
-IODATA (jp)
-------
-   GV-BCTV/PCI
-   GV-BCTV2/PCI
-   GV-BCTV3/PCI
-   GV-BCTV4/PCI
-   GV-VCP/PCI (capture only)
-   GV-VCP2/PCI (capture only)
-
-Canopus (jp)
--------
-   WinDVR	= Kworld "KW-TVL878RF"
-
-www.sigmacom.co.kr
-------------------
-   Sigma Cyber TV II
-
-www.sasem.co.kr
----------------
-   Litte OnAir TV
-
-hama
-----
-   TV/Radio-Tuner Card, PCI (Model 44677) = CPH051
-
-Sigma Designs
--------------
-   Hollywood plus (em8300, em9010, adv7175), (PCB "M340-10") MPEG DVD decoder
-
-Formac
-------
-   iProTV (Card for iMac Mezzanine slot, Bt848+SCSI)
-   ProTV (Bt848)
-   ProTV II = ProTV Stereo (Bt878) ["stereo" means FM stereo, tv is still mono]
-
-ATI
----
-   TV-Wonder
-   TV-Wonder VE
-
-Diamond Multimedia
-------------------
-   DTV2000 (Bt848, tda9875)
-
-Aopen
------
-   VA1000 Plus (w/ Stereo)
-   VA1000 Lite
-   VA1000 (=LR90)
-
-Intel
------
-   Smart Video Recorder (ISA full-length)
-   Smart Video Recorder pro (ISA half-length)
-   Smart Video Recorder III (Bt848)
-
-STB
----
-   STB Gateway 6000704 (bt878)
-   STB Gateway 6000699 (bt848)
-   STB Gateway 6000402 (bt848)
-   STB TV130 PCI
-
-Videologic
-----------
-   Captivator Pro/TV (ISA?)
-   Captivator PCI/VC (Bt848 bundled with camera) (capture only)
-
-Technotrend
-------------
-   TT-SAT PCI (PCB "Sat-PCI Rev.:1.3.1"; zr36125, vpx3225d, stc0056a, Tuner:BSKE6-155A
-   TT-DVB-Sat
-    revisions 1.1, 1.3, 1.5, 1.6 and 2.1
-    This card is sold as OEM from:
-	Siemens DVB-s Card
-	Hauppauge WinTV DVB-S
-	Technisat SkyStar 1 DVB
-	Galaxis DVB Sat
-    Now this card is called TT-PCline Premium Family
-   TT-Budget (saa7146, bsru6-701a)
-    This card is sold as OEM from:
-	Hauppauge WinTV Nova
-	Satelco Standard PCI (DVB-S)
-   TT-DVB-C PCI
-
-Teles
------
-   DVB-s (Rev. 2.2, BSRV2-301A, data only?)
-
-Remote Vision
--------------
-   MX RV605 (Bt848 capture only)
-
-Boeder
-------
-   PC ChatCam (Model 68252) (Bt848 capture only)
-   Tv/Fm Capture Card  (Model 68404) = PV951
-
-Media-Surfer  (esc-kathrein.de)
--------------------------------
-   Sat-Surfer (ISA)
-   Sat-Surfer PCI = Techni-PC-Sat
-   Cable-Surfer 1
-   Cable-Surfer 2
-   Cable-Surfer PCI (zr36120)
-   Audio-Surfer (ISA Radio card)
-
-Jetway (www.jetway.com.tw)
---------------------------
-   JW-TV 878M
-   JW-TV 878  = KWorld KW-TV878RF
-
-Galaxis
--------
-   Galaxis DVB Card S CI
-   Galaxis DVB Card C CI
-   Galaxis DVB Card S
-   Galaxis DVB Card C
-   Galaxis plug.in S [neuer Name: Galaxis DVB Card S CI
-
-Hauppauge
----------
-   many many WinTV models ...
-   WinTV DVBs = Technotrend Premium 1.3
-   WinTV NOVA = Technotrend Budget 1.1 "S-DVB DATA"
-   WinTV NOVA-CI "SDVBACI"
-   WinTV Nova USB (=Technotrend USB 1.0)
-   WinTV-Nexus-s (=Technotrend Premium 2.1 or 2.2)
-   WinTV PVR
-   WinTV PVR 250
-   WinTV PVR 450
-
-  US models
-  990 WinTV-PVR-350 (249USD) (iTVC15 chipset + radio)
-  980 WinTV-PVR-250 (149USD) (iTVC15 chipset)
-  880 WinTV-PVR-PCI (199USD) (KFIR chipset + bt878)
-  881 WinTV-PVR-USB
-  190 WinTV-GO
-  191 WinTV-GO-FM
-  404 WinTV
-  401 WinTV-radio
-  495 WinTV-Theater
-  602 WinTV-USB
-  621 WinTV-USB-FM
-  600 USB-Live
-  698 WinTV-HD
-  697 WinTV-D
-  564 WinTV-Nexus-S
-
-  Deutsche Modelle
-  603 WinTV GO
-  719 WinTV Primio-FM
-  718 WinTV PCI-FM
-  497 WinTV Theater
-  569 WinTV USB
-  568 WinTV USB-FM
-  882 WinTV PVR
-  981 WinTV PVR 250
-  891 WinTV-PVR-USB
-  541 WinTV Nova
-  488 WinTV Nova-Ci
-  564 WinTV-Nexus-s
-  727 WinTV-DVB-c
-  545 Common Interface
-  898 WinTV-Nova-USB
-
-  UK models
-  607 WinTV Go
-  693,793 WinTV Primio FM
-  647,747 WinTV PCI FM
-  498 WinTV Theater
-  883 WinTV PVR
-  893 WinTV PVR USB  (Duplicate entry)
-  566 WinTV USB (UK)
-  573 WinTV USB FM
-  429 Impact VCB (bt848)
-  600 USB Live (Video-In 1x Comp, 1xSVHS)
-  542 WinTV Nova
-  717 WinTV DVB-S
-  909 Nova-t PCI
-  893 Nova-t USB   (Duplicate entry)
-  802 MyTV
-  804 MyView
-  809 MyVideo
-  872 MyTV2Go FM
-
-
-  546 WinTV Nova-S CI
-  543 WinTV Nova
-  907 Nova-S USB
-  908 Nova-T USB
-  717 WinTV Nexus-S
-  157 DEC3000-s Standalone + USB
-
-  Spain
-  685 WinTV-Go
-  690 WinTV-PrimioFM
-  416 WinTV-PCI Nicam Estereo
-  677 WinTV-PCI-FM
-  699 WinTV-Theater
-  683 WinTV-USB
-  678 WinTV-USB-FM
-  983 WinTV-PVR-250
-  883 WinTV-PVR-PCI
-  993 WinTV-PVR-350
-  893 WinTV-PVR-USB
-  728 WinTV-DVB-C PCI
-  832 MyTV2Go
-  869 MyTV2Go-FM
-  805 MyVideo (USB)
-
-
-Matrix-Vision
--------------
-   MATRIX-Vision MV-Delta
-   MATRIX-Vision MV-Delta 2
-   MVsigma-SLC (Bt848)
-
-Conceptronic (.net)
-------------
-   TVCON FM,  TV card w/ FM = CPH05x
-   TVCON = CPH06x
-
-BestData
---------
-   HCC100 = VCC100rev1 + camera
-   VCC100 rev1 (bt848)
-   VCC100 rev2 (bt878)
-
-Gallant  (www.gallantcom.com) www.minton.com.tw
------------------------------------------------
-   Intervision IV-510 (capture only bt8x8)
-   Intervision IV-550 (bt8x8)
-   Intervision IV-100 (zoran)
-   Intervision IV-1000 (bt8x8)
-
-Asonic (www.asonic.com.cn) (website down)
------------------------------------------
-   SkyEye tv 878
-
-Hoontech
---------
-   878TV/FM
-
-Teppro (www.itcteppro.com.tw)
------------------------------
-   ITC PCITV (Card Ver 1.0) "Teppro TV1/TVFM1 Card"
-   ITC PCITV (Card Ver 2.0)
-   ITC PCITV (Card Ver 3.0) = "PV-BT878P+ (REV.9D)"
-   ITC PCITV (Card Ver 4.0)
-   TEPPRO IV-550 (For BT848 Main Chip)
-   ITC DSTTV (bt878, satellite)
-   ITC VideoMaker (saa7146, StreamMachine sm2110, tvtuner) "PV-SM2210P+ (REV:1C)"
-
-Kworld (www.kworld.com.tw)
---------------------------
-  PC TV Station
-   KWORLD KW-TV878R  TV (no radio)
-   KWORLD KW-TV878RF TV (w/ radio)
-
-   KWORLD KW-TVL878RF (low profile)
-
-   KWORLD KW-TV713XRF (saa7134)
-
-
-  MPEG TV Station (same cards as above plus WinDVR Software MPEG en/decoder)
-   KWORLD KW-TV878R -Pro   TV (no Radio)
-   KWORLD KW-TV878RF-Pro   TV (w/ Radio)
-   KWORLD KW-TV878R -Ultra TV (no Radio)
-   KWORLD KW-TV878RF-Ultra TV (w/ Radio)
-
-
-
-JTT/ Justy Corp.(http://www.jtt.ne.jp/)
----------------------------------------------------------------------
-   JTT-02 (JTT TV) "TV watchmate pro" (bt848)
-
-ADS www.adstech.com
--------------------
-   Channel Surfer TV ( CHX-950 )
-   Channel Surfer TV+FM ( CHX-960FM )
-
-AVEC www.prochips.com
----------------------
-   AVEC Intercapture (bt848, tea6320)
-
-NoBrand
--------
-   TV Excel = Australian Name for "PV-BT878P+ 8E" or "878TV Rev.3_"
-
-Mach www.machspeed.com
-----
-   Mach TV 878
-
-Eline www.eline-net.com/
------
-   Eline Vision TVMaster / TVMaster FM (ELV-TVM/ ELV-TVM-FM) = LR26  (bt878)
-   Eline Vision TVMaster-2000 (ELV-TVM-2000, ELV-TVM-2000-FM)= LR138 (saa713x)
-
-Spirit 
-------
-   Spirit TV Tuner/Video Capture Card (bt848)
-
-Boser www.boser.com.tw
------
-   HS-878 Mini PCI Capture Add-on Card
-   HS-879 Mini PCI 3D Audio and Capture Add-on Card (w/ ES1938 Solo-1)
-
-Satelco www.citycom-gmbh.de, www.satelco.de
--------
-   TV-FM =KNC1 saa7134
-   Standard PCI (DVB-S) = Technotrend Budget
-   Standard PCI (DVB-S) w/ CI
-   Satelco Highend PCI (DVB-S) = Technotrend Premium
-
-
-Sensoray www.sensoray.com
---------
-   Sensoray 311 (PC/104 bus)
-   Sensoray 611 (PCI)
-
-CEI (Chartered Electronics Industries Pte Ltd [CEI] [FCC ID HBY])
----
-  TV Tuner  -  HBY-33A-RAFFLES  Brooktree Bt848KPF + Philips
-  TV Tuner MG9910  -  HBY33A-TVO  CEI + Philips SAA7110 + OKI M548262 + ST STV8438CV
-  Primetime TV (ISA)
-   acquired by Singapore Technologies
-   now operating as Chartered Semiconductor Manufacturing
-   Manufacturer of video cards is listed as:
-   Cogent Electronics Industries [CEI]
-
-AITech
-------
-   Wavewatcher TV (ISA)
-   AITech WaveWatcher TV-PCI = can be LR26 (Bt848) or LR50 (BT878)
-   WaveWatcher TVR-202 TV/FM Radio Card (ISA)
-
-MAXRON
-------
-   Maxron MaxTV/FM Radio (KW-TV878-FNT) = Kworld or JW-TV878-FBK
-
-www.ids-imaging.de
-------------------
-   Falcon Series (capture only)
- In USA: http://www.theimagingsource.com/
-   DFG/LC1
-
-www.sknet-web.co.jp
--------------------
-   SKnet Monster TV (saa7134)
-
-A-Max www.amaxhk.com (Colormax, Amax, Napa)
--------------------
-   APAC Viewcomp 878
-
-Cybertainment
--------------
-   CyberMail AV Video Email Kit w/ PCI Capture Card (capture only)
-   CyberMail Xtreme
-  These are Flyvideo
-
-VCR (http://www.vcrinc.com/)
----
-  Video Catcher 16
-
-Twinhan
--------
-   DST Card/DST-IP (bt878, twinhan asic) VP-1020
-    Sold as:
-     KWorld DVBS Satellite TV-Card
-     Powercolor DSTV Satellite Tuner Card
-     Prolink Pixelview DTV2000
-     Provideo PV-911 Digital Satellite TV Tuner Card With Common Interface ?
-   DST-CI Card (DVB Satellite) VP-1030
-   DCT Card (DVB cable)
-
-MSI
----
-    MSI TV@nywhere Tuner Card (MS-8876) (CX23881/883) Not Bt878 compatible.
-    MS-8401 DVB-S
-
-Focus www.focusinfo.com
------
-    InVideo PCI (bt878)
-
-Sdisilk www.sdisilk.com/
--------
-    SDI Silk 100
-    SDI Silk 200 SDI Input Card
-
-www.euresys.com
-    PICOLO series
-
-PMC/Pace
-www.pacecom.co.uk website closed
-
-Mercury www.kobian.com (UK and FR)
-    LR50
-    LR138RBG-Rx  == LR138
-
-TEC sound (package and manuals don't have any other manufacturer info) TecSound
-    Though educated googling found: www.techmakers.com
-    TV-Mate = Zoltrix VP-8482
-
-Lorenzen www.lorenzen.de
---------
-     SL DVB-S PCI = Technotrend Budget PCI (su1278 or bsru version)
-
-Origo (.uk) www.origo2000.com
-     PC TV Card = LR50
-
-I/O Magic www.iomagic.com
----------
-    PC PVR - Desktop TV Personal Video Recorder DR-PCTV100 = Pinnacle ROB2D-51009464 4.0 + Cyberlink PowerVCR II
-
-Arowana
--------
-    TV-Karte / Poso Power TV (?) = Zoltrix VP-8482 (?)
-
-iTVC15 boards:
--------------
-kuroutoshikou.com ITVC15
-yuan.com MPG160 PCI TV (Internal PCI MPEG2 encoder card plus TV-tuner)
-
-Asus www.asuscom.com
-   Asus TV Tuner Card 880 NTSC (low profile, cx23880)
-   Asus TV (saa7134)
-
-Hoontech
---------
-http://www.hoontech.de/
-   HART Vision 848 (H-ART Vision 848)
-   HART Vision 878 (H-Art Vision 878)
diff --git a/Documentation/video4linux/bttv/ICs b/Documentation/video4linux/bttv/ICs
deleted file mode 100644
index 611315f87c3e..000000000000
--- a/Documentation/video4linux/bttv/ICs
+++ /dev/null
@@ -1,37 +0,0 @@
-all boards:
-
-Brooktree Bt848/848A/849/878/879: video capture chip
-
-
-
-Miro PCTV:
-
-Philips or Temic Tuner
-
-
-
-Hauppauge Win/TV pci (version 405):
-
-Microchip 24LC02B or
-Philips 8582E2Y: 256 Byte EEPROM with configuration information
-		 I2C 0xa0-0xa1, (24LC02B also responds to 0xa2-0xaf)
-Philips SAA5246AGP/E: Videotext decoder chip, I2C 0x22-0x23
-TDA9800: sound decoder
-Winbond W24257AS-35: 32Kx8 CMOS static RAM (Videotext buffer mem)
-14052B: analog switch for selection of sound source
-
-PAL:
-TDA5737: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners
-TSA5522: 1.4 GHz I2C-bus controlled synthesizer, I2C 0xc2-0xc3
-
-NTSC:
-TDA5731: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners
-TSA5518: no datasheet available on Philips site
-
-
-
-STB TV pci:
-
-???
-if you want better support for STB cards send me info!
-Look at the board! What chips are on it?
diff --git a/Documentation/video4linux/bttv/Insmod-options b/Documentation/video4linux/bttv/Insmod-options
deleted file mode 100644
index 14c065fa23ef..000000000000
--- a/Documentation/video4linux/bttv/Insmod-options
+++ /dev/null
@@ -1,172 +0,0 @@
-
-Note: "modinfo <module>" prints various information about a kernel
-module, among them a complete and up-to-date list of insmod options.
-This list tends to be outdated because it is updated manually ...
-
-==========================================================================
-
-bttv.o
-	the bt848/878 (grabber chip) driver
-
-	insmod args:
-		card=n		card type, see CARDLIST for a list.
-		tuner=n		tuner type, see CARDLIST for a list.
-		radio=0/1	card supports radio
-		pll=0/1/2	pll settings
-			0: don't use PLL
-			1: 28 MHz crystal installed
-			2: 35 MHz crystal installed
-
-		triton1=0/1     for Triton1 (+others) compatibility
-		vsfx=0/1	yet another chipset bug compatibility bit
-				see README.quirks for details on these two.
-
-		bigendian=n	Set the endianness of the gfx framebuffer.
-				Default is native endian.
-		fieldnr=0/1	Count fields.  Some TV descrambling software
-				needs this, for others it only generates
-				50 useless IRQs/sec.  default is 0 (off).
-		autoload=0/1	autoload helper modules (tuner, audio).
-				default is 1 (on).
-		bttv_verbose=0/1/2  verbose level (at insmod time, while
-				looking at the hardware).  default is 1.
-		bttv_debug=0/1	debug messages (for capture).
-				default is 0 (off).
-		irq_debug=0/1	irq handler debug messages.
-				default is 0 (off).
-		gbuffers=2-32	number of capture buffers for mmap'ed capture.
-				default is 4.
-		gbufsize=	size of capture buffers. default and
-				maximum value is 0x208000 (~2MB)
-		no_overlay=0	Enable overlay on broken hardware.  There
-				are some chipsets (SIS for example) which
-				are known to have problems with the PCI DMA
-				push used by bttv.  bttv will disable overlay
-				by default on this hardware to avoid crashes.
-				With this insmod option you can override this.
-		no_overlay=1	Disable overlay. It should be used by broken
-				hardware that doesn't support PCI2PCI direct
-				transfers.
-		automute=0/1	Automatically mutes the sound if there is
-				no TV signal, on by default.  You might try
-				to disable this if you have bad input signal
-				quality which leading to unwanted sound
-				dropouts.
-		chroma_agc=0/1	AGC of chroma signal, off by default.
-		adc_crush=0/1	Luminance ADC crush, on by default.
-		i2c_udelay=     Allow reduce I2C speed. Default is 5 usecs
-				(meaning 66,67 Kbps). The default is the
-				maximum supported speed by kernel bitbang
-				algorithm. You may use lower numbers, if I2C
-				messages are lost (16 is known to work on
-				all supported cards).
-
-		bttv_gpio=0/1
-		gpiomask=
-		audioall=
-		audiomux=
-				See Sound-FAQ for a detailed description.
-
-	remap, card, radio and pll accept up to four comma-separated arguments
-	(for multiple boards).
-
-tuner.o
-	The tuner driver.  You need this unless you want to use only
-	with a camera or external tuner ...
-
-	insmod args:
-		debug=1		print some debug info to the syslog
-		type=n		type of the tuner chip. n as follows:
-				see CARDLIST for a complete list.
-		pal=[bdgil]	select PAL variant (used for some tuners
-				only, important for the audio carrier).
-
-tvaudio.o
-	new, experimental module which is supported to provide a single
-	driver for all simple i2c audio control chips (tda/tea*).
-
-	insmod args:
-		tda8425  = 1	enable/disable the support for the
-		tda9840  = 1	various chips.
-		tda9850  = 1	The tea6300 can't be autodetected and is
-		tda9855  = 1	therefore off by default, if you have
-		tda9873  = 1	this one on your card (STB uses these)
-		tda9874a = 1	you have to enable it explicitly.
-		tea6300  = 0	The two tda985x chips use the same i2c
-		tea6420  = 1	address and can't be disturgished from
-		pic16c54 = 1	each other, you might have to disable
-				the wrong one.
-		debug = 1	print debug messages
-
-	insmod args for tda9874a:
-		tda9874a_SIF=1/2	select sound IF input pin (1 or 2)
-					(default is pin 1)
-		tda9874a_AMSEL=0/1	auto-mute select for NICAM (default=0)
-					Please read note 3 below!
-		tda9874a_STD=n		select TV sound standard (0..8):
-					0 - A2, B/G
-					1 - A2, M (Korea)
-					2 - A2, D/K (1)
-					3 - A2, D/K (2)
-					4 - A2, D/K (3)
-					5 - NICAM, I
-					6 - NICAM, B/G
-					7 - NICAM, D/K (default)
-					8 - NICAM, L
-
-	Note 1: tda9874a supports both tda9874h (old) and tda9874a (new) chips.
-	Note 2: tda9874h/a and tda9875 (which is supported separately by
-	tda9875.o) use the same i2c address so both modules should not be
-	used at the same time.
-	Note 3: Using tda9874a_AMSEL option depends on your TV card design!
-		AMSEL=0: auto-mute will switch between NICAM sound
-			 and the sound on 1st carrier (i.e. FM mono or AM).
-		AMSEL=1: auto-mute will switch between NICAM sound
-			 and the analog mono input (MONOIN pin).
-	If tda9874a decoder on your card has MONOIN pin not connected, then
-	use only tda9874_AMSEL=0 or don't specify this option at all.
-	For example:
-	  card=65 (FlyVideo 2000S) - set AMSEL=1 or AMSEL=0
-	  card=72 (Prolink PV-BT878P rev.9B) - set AMSEL=0 only
-
-msp3400.o
-	The driver for the msp34xx sound processor chips. If you have a
-	stereo card, you probably want to insmod this one.
-
-	insmod args:
-		debug=1/2	print some debug info to the syslog,
-				2 is more verbose.
-		simple=1	Use the "short programming" method.  Newer
-				msp34xx versions support this.  You need this
-				for dbx stereo.  Default is on if supported by
-				the chip.
-		once=1		Don't check the TV-stations Audio mode
-				every few seconds, but only once after
-				channel switches.
-		amsound=1	Audio carrier is AM/NICAM at 6.5 Mhz.  This
-				should improve things for french people, the
-				carrier autoscan seems to work with FM only...
-
-tea6300.o - OBSOLETE (use tvaudio instead)
-	The driver for the tea6300 fader chip.  If you have a stereo
-	card and the msp3400.o doesn't work, you might want to try this
-	one.  This chip is seen on most STB TV/FM cards (usually from
-	Gateway OEM sold surplus on auction sites).
-
-	insmod args:
-		debug=1		print some debug info to the syslog.
-
-tda8425.o - OBSOLETE (use tvaudio instead)
-	The driver for the tda8425 fader chip.  This driver used to be
-	part of bttv.c, so if your sound used to work but does not
-	anymore, try loading this module.
-
-	insmod args:
-		debug=1		print some debug info to the syslog.
-
-tda985x.o - OBSOLETE (use tvaudio instead)
-	The driver for the tda9850/55 audio chips.
-
-	insmod args:
-		debug=1		print some debug info to the syslog.
-		chip=9850/9855	set the chip type.
diff --git a/Documentation/video4linux/bttv/MAKEDEV b/Documentation/video4linux/bttv/MAKEDEV
deleted file mode 100644
index 093c0cd18042..000000000000
--- a/Documentation/video4linux/bttv/MAKEDEV
+++ /dev/null
@@ -1,27 +0,0 @@
-#!/bin/bash
-
-function makedev () {
-
-	for dev in 0 1 2 3; do
-		echo "/dev/$1$dev: char 81 $[ $2 + $dev ]"
-		rm -f /dev/$1$dev
-		mknod /dev/$1$dev c 81 $[ $2 + $dev ]
-		chmod 666 /dev/$1$dev
-	done
-
-	# symlink for default device
-	rm -f /dev/$1
-	ln -s /dev/${1}0 /dev/$1
-}
-
-# see http://linux.bytesex.org/v4l2/API.html
-
-echo "*** new device names ***"
-makedev video 0
-makedev radio 64
-makedev vbi 224
-
-#echo "*** old device names (for compatibility only) ***"
-#makedev bttv 0
-#makedev bttv-fm 64
-#makedev bttv-vbi 224
diff --git a/Documentation/video4linux/bttv/Modprobe.conf b/Documentation/video4linux/bttv/Modprobe.conf
deleted file mode 100644
index 55f14650d8cd..000000000000
--- a/Documentation/video4linux/bttv/Modprobe.conf
+++ /dev/null
@@ -1,11 +0,0 @@
-# i2c
-alias char-major-89	i2c-dev
-options i2c-core	i2c_debug=1
-options i2c-algo-bit	bit_test=1
-
-# bttv
-alias char-major-81	videodev
-alias char-major-81-0	bttv
-options	bttv		card=2 radio=1
-options	tuner		debug=1
-
diff --git a/Documentation/video4linux/bttv/Modules.conf b/Documentation/video4linux/bttv/Modules.conf
deleted file mode 100644
index 8f258faf18f1..000000000000
--- a/Documentation/video4linux/bttv/Modules.conf
+++ /dev/null
@@ -1,14 +0,0 @@
-# For modern kernels (2.6 or above), this belongs in /etc/modprobe.d/*.conf
-# For for 2.4 kernels or earlier, this belongs in /etc/modules.conf.
-
-# i2c
-alias char-major-89	i2c-dev
-options i2c-core	i2c_debug=1
-options i2c-algo-bit	bit_test=1
-
-# bttv
-alias char-major-81	videodev
-alias char-major-81-0	bttv
-options	bttv		card=2 radio=1
-options	tuner		debug=1
-
diff --git a/Documentation/video4linux/bttv/PROBLEMS b/Documentation/video4linux/bttv/PROBLEMS
deleted file mode 100644
index 2b8b0079f7c7..000000000000
--- a/Documentation/video4linux/bttv/PROBLEMS
+++ /dev/null
@@ -1,62 +0,0 @@
-- Start capturing by pressing "c" or by selecting it via a menu!
-
-- Start capturing by pressing "c" or by selecting it via a menu!!!
-
-- The memory of some S3 cards is not recognized right:
-
-  First of all, if you are not using XFree-3.2 or newer, upgrade AT LEAST to
-  XFree-3.2A! This solved the problem for most people.
-
-  Start up X11 like this: "XF86_S3 -probeonly" and write down where the
-  linear frame buffer is.
-  If it is different to the address found by bttv install bttv like this:
-  "insmod bttv vidmem=0xfb0"
-  if the linear frame buffer is at 0xfb000000 (i.e. omit the last 5 zeros!)
-
-  Some S3 cards even take up 64MB of memory but only report 32MB to the BIOS.
-  If this 64MB area overlaps the IO memory of the Bt848 you also have to
-  remap this. E.g.: insmod bttv vidmem=0xfb0 remap=0xfa0
-
-  If the video memory is found at the right place and there are no address
-  conflicts but still no picture (or the computer even crashes),
-  try disabling features of your PCI chipset in the BIOS setup.
-
-  Frank Kapahnke <frank@kapahnke.prima.ruhr.de> also reported that problems
-  with his S3 868 went away when he upgraded to XFree 3.2.
-
-
-- I still only get a black picture with my S3 card!
-
-  Even with XFree-3.2A some people have problems with their S3 cards
-  (mostly with Trio 64 but also with some others)
-  Get the free demo version of Accelerated X from www.xinside.com and try
-  bttv with it. bttv seems to work with most S3 cards with Accelerated X.
-
-  Since I do not know much (better make that almost nothing) about VGA card
-  programming I do not know the reason for this.
-  Looks like XFree does something different when setting up the video memory?
-  Maybe somebody can enlighten me?
-  Would be nice if somebody could get this to work with XFree since
-  Accelerated X costs more than some of the grabber cards ...
-
-  Better linear frame buffer support for S3 cards will probably be in
-  XFree 4.0.
-
-- Grabbing is not switched off when changing consoles with XFree.
-  That's because XFree and some AcceleratedX versions do not send unmap
-  events.
-
-- Some popup windows (e.g. of the window manager) are not refreshed.
-
-  Disable backing store by starting X with the option "-bs"
-
-- When using 32 bpp in XFree or 24+8bpp mode in AccelX 3.1 the system
-  can sometimes lock up if you use more than 1 bt848 card at the same time.
-  You will always get pixel errors when e.g. using more than 1 card in full
-  screen mode. Maybe we need something faster than the PCI bus ...
-
-
-- Some S3 cards and the Matrox Mystique will produce pixel errors with
-  full resolution in 32-bit mode.
-
-- Some video cards have problems with Accelerated X 4.1
diff --git a/Documentation/video4linux/bttv/README b/Documentation/video4linux/bttv/README
deleted file mode 100644
index 7cbf4fb6cf31..000000000000
--- a/Documentation/video4linux/bttv/README
+++ /dev/null
@@ -1,90 +0,0 @@
-
-Release notes for bttv
-======================
-
-You'll need at least these config options for bttv:
-	CONFIG_I2C=m
-	CONFIG_I2C_ALGOBIT=m
-	CONFIG_VIDEO_DEV=m
-
-The latest bttv version is available from http://bytesex.org/bttv/
-
-
-Make bttv work with your card
------------------------------
-
-Just try "modprobe bttv" and see if that works.
-
-If it doesn't bttv likely could not autodetect your card and needs some
-insmod options.  The most important insmod option for bttv is "card=n"
-to select the correct card type.  If you get video but no sound you've
-very likely specified the wrong (or no) card type.  A list of supported
-cards is in CARDLIST.bttv
-
-If bttv takes very long to load (happens sometimes with the cheap
-cards which have no tuner), try adding this to your modules.conf:
-	options i2c-algo-bit bit_test=1
-
-For the WinTV/PVR you need one firmware file from the driver CD:
-hcwamc.rbf.  The file is in the pvr45xxx.exe archive (self-extracting
-zip file, unzip can unpack it).  Put it into the /etc/pvr directory or
-use the firm_altera=<path> insmod option to point the driver to the
-location of the file.
-
-If your card isn't listed in CARDLIST.bttv or if you have trouble making
-audio work, you should read the Sound-FAQ.
-
-
-Autodetecting cards
--------------------
-
-bttv uses the PCI Subsystem ID to autodetect the card type.  lspci lists
-the Subsystem ID in the second line, looks like this:
-
-00:0a.0 Multimedia video controller: Brooktree Corporation Bt878 (rev 02)
-	Subsystem: Hauppauge computer works Inc. WinTV/GO
-	Flags: bus master, medium devsel, latency 32, IRQ 5
-	Memory at e2000000 (32-bit, prefetchable) [size=4K]
-
-only bt878-based cards can have a subsystem ID (which does not mean
-that every card really has one).  bt848 cards can't have a Subsystem
-ID and therefore can't be autodetected.  There is a list with the ID's
-in bttv-cards.c (in case you are intrested or want to mail patches
-with updates).
-
-
-Still doesn't work?
--------------------
-
-I do NOT have a lab with 30+ different grabber boards and a
-PAL/NTSC/SECAM test signal generator at home, so I often can't
-reproduce your problems.  This makes debugging very difficult for me.
-If you have some knowledge and spare time, please try to fix this
-yourself (patches very welcome of course...)  You know: The linux
-slogan is "Do it yourself".
-
-There is a mailing list: linux-media@vger.kernel.org
-http://vger.kernel.org/vger-lists.html#linux-media
-
-If you have trouble with some specific TV card, try to ask there
-instead of mailing me directly.  The chance that someone with the
-same card listens there is much higher...
-
-For problems with sound:  There are a lot of different systems used
-for TV sound all over the world.  And there are also different chips
-which decode the audio signal.  Reports about sound problems ("stereo
-does'nt work") are pretty useless unless you include some details
-about your hardware and the TV sound scheme used in your country (or
-at least the country you are living in).
-
-
-Finally: If you mail some patches for bttv around the world (to
-linux-kernel/Alan/Linus/...), please Cc: me.
-
-
-Have fun with bttv,
-
-  Gerd
-
---
-Gerd Knorr <kraxel@bytesex.org>
diff --git a/Documentation/video4linux/bttv/README.WINVIEW b/Documentation/video4linux/bttv/README.WINVIEW
deleted file mode 100644
index c61cf2864287..000000000000
--- a/Documentation/video4linux/bttv/README.WINVIEW
+++ /dev/null
@@ -1,33 +0,0 @@
-
-Support for the Leadtek WinView 601 TV/FM by Jon Tombs <jon@gte.esi.us.es>
-
-This card is basically the same as all the rest (Bt484A, Philips tuner),
-the main difference is that they have attached a programmable attenuator to 3
-GPIO lines in order to give some volume control. They have also stuck an
-infra-red remote control decoded on the board, I will add support for this
-when I get time (it simple generates an interrupt for each key press, with
-the key code is placed in the GPIO port).
-
-I don't yet have any application to test the radio support. The tuner
-frequency setting should work but it is possible that the audio multiplexer
-is wrong. If it doesn't work, send me email.
-
-
-- No Thanks to Leadtek they refused to answer any questions about their
-hardware. The driver was written by visual inspection of the card. If you
-use this driver, send an email insult to them, and tell them you won't
-continue buying their hardware unless they support Linux.
-
-- Little thanks to Princeton Technology Corp (http://www.princeton.com.tw)
-who make the audio attenuator. Their publicly available data-sheet available
-on their web site doesn't include the chip programming information! Hidden
-on their server are the full data-sheets, but don't ask how I found it.
-
-To use the driver I use the following options, the tuner and pll settings might
-be different in your country
-
-insmod videodev
-insmod i2c scan=1 i2c_debug=0 verbose=0
-insmod tuner type=1 debug=0
-insmod bttv  pll=1 radio=1 card=17
-
diff --git a/Documentation/video4linux/bttv/README.freeze b/Documentation/video4linux/bttv/README.freeze
deleted file mode 100644
index 5eddfa076cfb..000000000000
--- a/Documentation/video4linux/bttv/README.freeze
+++ /dev/null
@@ -1,74 +0,0 @@
-
-If the box freezes hard with bttv ...
-=====================================
-
-It might be a bttv driver bug.  It also might be bad hardware.  It also
-might be something else ...
-
-Just mailing me "bttv freezes" isn't going to help much.  This README
-has a few hints how you can help to pin down the problem.
-
-
-bttv bugs
----------
-
-If some version works and another doesn't it is likely to be a driver
-bug.  It is very helpful if you can tell where exactly it broke
-(i.e. the last working and the first broken version).
-
-With a hard freeze you probably doesn't find anything in the logfiles.
-The only way to capture any kernel messages is to hook up a serial
-console and let some terminal application log the messages.  /me uses
-screen.  See Documentation/serial-console.txt for details on setting
-up a serial console.
-
-Read Documentation/oops-tracing.txt to learn how to get any useful
-information out of a register+stack dump printed by the kernel on
-protection faults (so-called "kernel oops").
-
-If you run into some kind of deadlock, you can try to dump a call trace
-for each process using sysrq-t (see Documentation/sysrq.txt).
-This way it is possible to figure where *exactly* some process in "D"
-state is stuck.
-
-I've seen reports that bttv 0.7.x crashes whereas 0.8.x works rock solid
-for some people.  Thus probably a small buglet left somewhere in bttv
-0.7.x.  I have no idea where exactly, it works stable for me and a lot of
-other people.  But in case you have problems with the 0.7.x versions you
-can give 0.8.x a try ...
-
-
-hardware bugs
--------------
-
-Some hardware can't deal with PCI-PCI transfers (i.e. grabber => vga).
-Sometimes problems show up with bttv just because of the high load on
-the PCI bus. The bt848/878 chips have a few workarounds for known
-incompatibilities, see README.quirks.
-
-Some folks report that increasing the pci latency helps too,
-althrought I'm not sure whenever this really fixes the problems or
-only makes it less likely to happen.  Both bttv and btaudio have a
-insmod option to set the PCI latency of the device.
-
-Some mainboard have problems to deal correctly with multiple devices
-doing DMA at the same time.  bttv + ide seems to cause this sometimes,
-if this is the case you likely see freezes only with video and hard disk
-access at the same time.  Updating the IDE driver to get the latest and
-greatest workarounds for hardware bugs might fix these problems.
-
-
-other
------
-
-If you use some binary-only yunk (like nvidia module) try to reproduce
-the problem without.
-
-IRQ sharing is known to cause problems in some cases.  It works just
-fine in theory and many configurations.  Neverless it might be worth a
-try to shuffle around the PCI cards to give bttv another IRQ or make
-it share the IRQ with some other piece of hardware.  IRQ sharing with
-VGA cards seems to cause trouble sometimes.  I've also seen funny
-effects with bttv sharing the IRQ with the ACPI bridge (and
-apci-enabled kernel).
-
diff --git a/Documentation/video4linux/bttv/README.quirks b/Documentation/video4linux/bttv/README.quirks
deleted file mode 100644
index 92e03929a6b2..000000000000
--- a/Documentation/video4linux/bttv/README.quirks
+++ /dev/null
@@ -1,83 +0,0 @@
-
-Below is what the bt878 data book says about the PCI bug compatibility
-modes of the bt878 chip.
-
-The triton1 insmod option sets the EN_TBFX bit in the control register.
-The vsfx insmod option does the same for EN_VSFX bit.  If you have
-stability problems you can try if one of these options makes your box
-work solid.
-
-drivers/pci/quirks.c knows about these issues, this way these bits are
-enabled automagically for known-buggy chipsets (look at the kernel
-messages, bttv tells you).
-
-HTH,
-
-  Gerd
-
----------------------------- cut here --------------------------
-
-Normal PCI Mode
----------------
-
-The PCI REQ signal is the logical-or of the incoming function requests.
-The inter-nal GNT[0:1] signals are gated asynchronously with GNT and
-demultiplexed by the audio request signal. Thus the arbiter defaults to
-the video function at power-up and parks there during no requests for
-bus access. This is desirable since the video will request the bus more
-often. However, the audio will have highest bus access priority. Thus
-the audio will have first access to the bus even when issuing a request
-after the video request but before the PCI external arbiter has granted
-access to the Bt879. Neither function can preempt the other once on the
-bus. The duration to empty the entire video PCI FIFO onto the PCI bus is
-very short compared to the bus access latency the audio PCI FIFO can
-tolerate.
-
-
-430FX Compatibility Mode
-------------------------
-
-When using the 430FX PCI, the following rules will ensure
-compatibility:
-
- (1) Deassert REQ at the same time as asserting FRAME.
- (2) Do not reassert REQ to request another bus transaction until after
-     finish-ing the previous transaction.
-
-Since the individual bus masters do not have direct control of REQ, a
-simple logical-or of video and audio requests would violate the rules.
-Thus, both the arbiter and the initiator contain 430FX compatibility
-mode logic. To enable 430FX mode, set the EN_TBFX bit as indicated in
-Device Control Register on page 104.
-
-When EN_TBFX is enabled, the arbiter ensures that the two compatibility
-rules are satisfied. Before GNT is asserted by the PCI arbiter, this
-internal arbiter may still logical-or the two requests. However, once
-the GNT is issued, this arbiter must lock in its decision and now route
-only the granted request to the REQ pin. The arbiter decision lock
-happens regardless of the state of FRAME because it does not know when
-FRAME will be asserted (typically - each initiator will assert FRAME on
-the cycle following GNT). When FRAME is asserted, it is the initiator s
-responsibility to remove its request at the same time. It is the
-arbiters responsibility to allow this request to flow through to REQ and
-not allow the other request to hold REQ asserted. The decision lock may
-be removed at the end of the transaction: for example, when the bus is
-idle (FRAME and IRDY). The arbiter decision may then continue
-asynchronously until GNT is again asserted.
-
-
-Interfacing with Non-PCI 2.1 Compliant Core Logic
--------------------------------------------------
-
-A small percentage of core logic devices may start a bus transaction
-during the same cycle that GNT is de-asserted. This is non PCI 2.1
-compliant. To ensure compatibility when using PCs with these PCI
-controllers, the EN_VSFX bit must be enabled (refer to Device Control
-Register on page 104). When in this mode, the arbiter does not pass GNT
-to the internal functions unless REQ is asserted. This prevents a bus
-transaction from starting the same cycle as GNT is de-asserted. This
-also has the side effect of not being able to take advantage of bus
-parking, thus lowering arbitration performance. The Bt879 drivers must
-query for these non-compliant devices, and set the EN_VSFX bit only if
-required.
-
diff --git a/Documentation/video4linux/bttv/Sound-FAQ b/Documentation/video4linux/bttv/Sound-FAQ
deleted file mode 100644
index 646a47de0016..000000000000
--- a/Documentation/video4linux/bttv/Sound-FAQ
+++ /dev/null
@@ -1,148 +0,0 @@
-
-bttv and sound mini howto
-=========================
-
-There are a lot of different bt848/849/878/879 based boards available.
-Making video work often is not a big deal, because this is handled
-completely by the bt8xx chip, which is common on all boards.  But
-sound is handled in slightly different ways on each board.
-
-To handle the grabber boards correctly, there is a array tvcards[] in
-bttv-cards.c, which holds the information required for each board.
-Sound will work only, if the correct entry is used (for video it often
-makes no difference).  The bttv driver prints a line to the kernel
-log, telling which card type is used.  Like this one:
-
-	bttv0: model: BT848(Hauppauge old) [autodetected]
-
-You should verify this is correct.  If it isn't, you have to pass the
-correct board type as insmod argument, "insmod bttv card=2" for
-example.  The file CARDLIST has a list of valid arguments for card.
-If your card isn't listed there, you might check the source code for
-new entries which are not listed yet.  If there isn't one for your
-card, you can check if one of the existing entries does work for you
-(just trial and error...).
-
-Some boards have an extra processor for sound to do stereo decoding
-and other nice features.  The msp34xx chips are used by Hauppauge for
-example.  If your board has one, you might have to load a helper
-module like msp3400.o to make sound work.  If there isn't one for the
-chip used on your board:  Bad luck.  Start writing a new one.  Well,
-you might want to check the video4linux mailing list archive first...
-
-Of course you need a correctly installed soundcard unless you have the
-speakers connected directly to the grabber board.  Hint: check the
-mixer settings too.  ALSA for example has everything muted by default.
-
-
-How sound works in detail
-=========================
-
-Still doesn't work?  Looks like some driver hacking is required.
-Below is a do-it-yourself description for you.
-
-The bt8xx chips have 32 general purpose pins, and registers to control
-these pins.  One register is the output enable register
-(BT848_GPIO_OUT_EN), it says which pins are actively driven by the
-bt848 chip.  Another one is the data register (BT848_GPIO_DATA), where
-you can get/set the status if these pins.  They can be used for input
-and output.
-
-Most grabber board vendors use these pins to control an external chip
-which does the sound routing.  But every board is a little different.
-These pins are also used by some companies to drive remote control
-receiver chips.  Some boards use the i2c bus instead of the gpio pins
-to connect the mux chip.
-
-As mentioned above, there is a array which holds the required
-information for each known board.  You basically have to create a new
-line for your board.  The important fields are these two:
-
-struct tvcard
-{
-	[ ... ]
-	u32 gpiomask;
-	u32 audiomux[6]; /* Tuner, Radio, external, internal, mute, stereo */
-};
-
-gpiomask specifies which pins are used to control the audio mux chip.
-The corresponding bits in the output enable register
-(BT848_GPIO_OUT_EN) will be set as these pins must be driven by the
-bt848 chip.
-
-The audiomux[] array holds the data values for the different inputs
-(i.e. which pins must be high/low for tuner/mute/...).  This will be
-written to the data register (BT848_GPIO_DATA) to switch the audio
-mux.
-
-
-What you have to do is figure out the correct values for gpiomask and
-the audiomux array.  If you have Windows and the drivers four your
-card installed, you might to check out if you can read these registers
-values used by the windows driver.  A tool to do this is available
-from ftp://telepresence.dmem.strath.ac.uk/pub/bt848/winutil, but it
-does'nt work with bt878 boards according to some reports I received.
-Another one with bt878 support is available from
-http://btwincap.sourceforge.net/Files/btspy2.00.zip
-
-You might also dig around in the *.ini files of the Windows applications.
-You can have a look at the board to see which of the gpio pins are
-connected at all and then start trial-and-error ...
-
-
-Starting with release 0.7.41 bttv has a number of insmod options to
-make the gpio debugging easier:
-
-bttv_gpio=0/1		enable/disable gpio debug messages
-gpiomask=n		set the gpiomask value
-audiomux=i,j,...	set the values of the audiomux array
-audioall=a		set the values of the audiomux array (one
-			value for all array elements, useful to check
-			out which effect the particular value has).
-
-The messages printed with bttv_gpio=1 look like this:
-
-	bttv0: gpio: en=00000027, out=00000024 in=00ffffd8 [audio: off]
-
-en  =	output _en_able register (BT848_GPIO_OUT_EN)
-out =	_out_put bits of the data register (BT848_GPIO_DATA),
-	i.e. BT848_GPIO_DATA & BT848_GPIO_OUT_EN
-in  = 	_in_put bits of the data register,
-	i.e. BT848_GPIO_DATA & ~BT848_GPIO_OUT_EN
-
-
-
-Other elements of the tvcards array
-===================================
-
-If you are trying to make a new card work you might find it useful to
-know what the other elements in the tvcards array are good for:
-
-video_inputs    - # of video inputs the card has
-audio_inputs    - historical cruft, not used any more.
-tuner           - which input is the tuner
-svhs            - which input is svhs (all others are labeled composite)
-muxsel          - video mux, input->registervalue mapping
-pll             - same as pll= insmod option
-tuner_type      - same as tuner= insmod option
-*_modulename    - hint whenever some card needs this or that audio
-		  module loaded to work properly.
-has_radio	- whenever this TV card has a radio tuner.
-no_msp34xx	- "1" disables loading of msp3400.o module
-no_tda9875	- "1" disables loading of tda9875.o module
-needs_tvaudio	- set to "1" to load tvaudio.o module
-
-If some config item is specified both from the tvcards array and as
-insmod option, the insmod option takes precedence.
-
-
-
-Good luck,
-
-  Gerd
-
-
-PS: If you have a new working entry, mail it to me.
-
---
-Gerd Knorr <kraxel@bytesex.org>
diff --git a/Documentation/video4linux/bttv/Specs b/Documentation/video4linux/bttv/Specs
deleted file mode 100644
index f32466cdae05..000000000000
--- a/Documentation/video4linux/bttv/Specs
+++ /dev/null
@@ -1,3 +0,0 @@
-Philips		http://www.Semiconductors.COM/pip/
-Conexant	http://www.conexant.com/
-Micronas	http://www.micronas.com/en/home/index.html
diff --git a/Documentation/video4linux/bttv/THANKS b/Documentation/video4linux/bttv/THANKS
deleted file mode 100644
index 950aa781c2e9..000000000000
--- a/Documentation/video4linux/bttv/THANKS
+++ /dev/null
@@ -1,24 +0,0 @@
-Many thanks to:
-
-- Markus Schroeder <schroedm@uni-duesseldorf.de> for information on the Bt848
-  and tuner programming and his control program xtvc.
-
-- Martin Buck <martin-2.buck@student.uni-ulm.de> for his great Videotext
-  package.
-
-- Gerd Knorr <kraxel@cs.tu-berlin.de> for the MSP3400 support and the modular
-  I2C, tuner, ... support.
-
-
-- MATRIX Vision for giving us 2 cards for free, which made support of
-  single crystal operation possible.
-
-- MIRO for providing a free PCTV card and detailed information about the
-  components on their cards. (E.g. how the tuner type is detected)
-  Without their card I could not have debugged the NTSC mode.
-
-- Hauppauge for telling how the sound input is selected and what components
-  they do and will use on their radio cards.
-  Also many thanks for faxing me the FM1216 data sheet.
-
-