Merge tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pin control updates from Linus Walleij:
 "This kernel cycle was quite calm when it comes to pin control and
  there is really just one major change, and that is the introduction of
  devm_pinctrl_register() managed resources.

  Apart from that linear development, details below.

  Core changes:

   - Add the devm_pinctrl_register() API and switch all applicable
     drivers to use it, saving lots of lines of code all over the place.

  New drivers:

   - driver for the Broadcom NS2 SoC

   - subdriver for the PXA25x SoCs

   - subdriver for the AMLogic Meson GXBB SoC

  Driver improvements:

   - the Intel Baytrail driver now properly supports pin control

   - Nomadik, Rockchip, Broadcom BCM2835 support the .get_direction()
     callback in the GPIO portions

   - continued development and stabilization of several SH-PFC SoC
     subdrivers: r8a7795, r8a7790, r8a7794 etc"

* tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (85 commits)
  Revert "pinctrl: tegra: avoid parked_reg and parked_bank"
  pinctrl: meson: Fix eth_tx_en bit index
  pinctrl: tegra: avoid parked_reg and parked_bank
  pinctrl: tegra: Correctly check the supported configuration
  pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC
  pinctrl: rockchip: fix pull setting error for rk3399
  pinctrl: stm32: Implement .pin_config_dbg_show()
  pinctrl: nomadik: hide nmk_gpio_get_mode when unused
  pinctrl: ns2: rename pinctrl_utils_dt_free_map
  pinctrl: at91: Merge clk_prepare and clk_enable into clk_prepare_enable
  pinctrl: at91: Make at91_gpio_template const
  pinctrl: baytrail: fix some error handling in debugfs
  pinctrl: ns2: add pinmux driver support for Broadcom NS2 SoC
  pinctrl: sirf/atlas7: trivial fix of spelling mistake on flagged
  pinctrl: sh-pfc: Kill unused variable in sh_pfc_remove()
  pinctrl: nomadik: implement .get_direction()
  pinctrl: nomadik: use BIT() with offsets consequently
  pinctrl: exynos5440: Use off-stack memory for pinctrl_gpio_range
  pinctrl: zynq: Use devm_pinctrl_register() for pinctrl registration
  pinctrl: u300: Use devm_pinctrl_register() for pinctrl registration
  ...

2 files changed, 4 insertions, 2 deletions

diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt
index ffadb7a371f6..74e6ec0339d6 100644
--- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt
@@ -72,8 +72,8 @@ Pin Configuration Node Properties:
 
 The pin configuration parameters use the generic pinconf bindings defined in
 pinctrl-bindings.txt in this directory. The supported parameters are
-bias-disable, bias-pull-up, bias-pull-down and power-source. For pins that
-have a configurable I/O voltage, the power-source value should be the
+bias-disable, bias-pull-up, bias-pull-down, drive strength and power-source. For
+pins that have a configurable I/O voltage, the power-source value should be the
 nominal I/O voltage in millivolts.
 
 
diff --git a/Documentation/driver-model/devres.txt b/Documentation/driver-model/devres.txt
index 73b98dfbcea4..e89f7b51f243 100644
--- a/Documentation/driver-model/devres.txt
+++ b/Documentation/driver-model/devres.txt
@@ -328,6 +328,8 @@ PHY
 PINCTRL
   devm_pinctrl_get()
   devm_pinctrl_put()
+  devm_pinctrl_register()
+  devm_pinctrl_unregister()
 
 PWM
   devm_pwm_get()