Merge tag 'sound-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound

Pull sound updates from Takashi Iwai:
 "There have been lots of changes in ALSA core, HD-audio and ASoC, also
  most of PCI drivers touched by conversions of printks.  All these
  resulted in a high volume and wide ranged patch sets in this release.
  Many changes are fairly trivial, but also lots of nice cleanups and
  refactors.  There are a few new drivers, most notably, the Intel
  Haswell and Baytrail ASoC driver.

  Core changes:
   - A bit modernization; embed the device struct into snd_card struct,
     so that it may be referred from the beginning.  A new
     snd_card_new() function is introduced for that, and all drivers
     have been converted.

   - Simplification in the device management code in ALSA core; now
     managed by a simple priority list instead

   - Converted many kernel messages to use the standard dev_err() & co;
     this would be the pretty visible difference, especially for
     HD-audio.

  HD-audio:
   - Conexant codecs use the auto-parser as default now; the old static
     code still remains in case of regressions.  Some old quirks have
     been rewritten with the fixups for auto-parser.

   - C-Media codecs also use the auto-parser as default now, too.

   - A device struct is assigned to each HD-audio codec, and the
     formerly hwdep attributes are accessible over the codec sysfs, too.
     hwdep attributes still remain for compatibility.

   - Split the PCI-specific stuff for HD-audio controller into a
     separate module, ane make a helper module for the generic
     controller driver.  This is a preliminary change for supporting
     Tegra HDMI controller in near future, which slipped from 3.15
     merge.

   - Device-specific fixes: mute LED support for Lenovo Ideapad, mic LED
     fix for HP laptops, more ASUS subwoofer quirks, yet more Dell
     laptop headset quirks

   - Make the HD-audio codec response a bit more robust

   - A few improvements on Realtek ALC282 / 283 about the pop noises

   - A couple of Intel HDMI fixes

  ASoC:
   - Lots of cleanups for enumerations; refactored lots of error prone
     original codes to use more modern APIs

   - Elimination of the ASoC level wrappers for I2C and SPI moving us
     closer to converting to regmap completely and avoiding some
     randconfig hassle

   - Provide both manually and transparently locked DAPM APIs rather
     than a mix of the two fixing some concurrency issues

   - Start converting CODEC drivers to use separate bus interface
     drivers rather than having them all in one file helping avoid
     dependency issues

   - DPCM support for Intel Haswell and Bay Trail platforms, lots of
     fixes

   - Lots of work on improvements for simple-card, DaVinci and the
     Renesas rcar drivers.

   - New drivers for Analog Devices ADAU1977, TI PCM512x and parts of
     the CSR SiRF SoC, TLV320AIC31XXX, Armada 370 DB, Cirrus cs42xx8

   - Fixes for the simple-card DAI format DT mess

   - DT support for a couple more devices.

   - Use of the tdm_slot mapping in a few drivers

  Others:
   - Support of reset_resume callback for improved S4 in USB-audio
     driver; the device with boot quirks have been little tested, which
     we need to watch out in this development cycle

   - Add PM support for ICE1712 driver (finally!); it's still pretty
     partial support, only for M-Audio devices"

* tag 'sound-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (610 commits)
  ALSA: ice1712: Add suspend support for M-Audio ICE1712-based cards
  ALSA: ice1712: add suspend support for ICE1712 chip
  ALSA: hda - Enable beep for ASUS 1015E
  ALSA: asihpi: fix some indenting in snd_card_asihpi_pcm_new()
  ALSA: hda - add headset mic detect quirks for three Dell laptops
  ASoC: tegra: move AC97 clock handling to the machine driver
  ASoC: simple-card: Handle many DAI links
  ASoC: simple-card: Add DT documentation for multi-DAI links
  ASoC: simple-card: dynamically allocate the DAI link and properties
  ASoC: imx-ssi: Add .xlate_tdm_slot_mask() support.
  ASoC: fsl-esai: Add .xlate_tdm_slot_mask() support.
  ASoC: fsl-utils: Add fsl_asoc_xlate_tdm_slot_mask() support.
  ASoC: core: remove the 'of_' prefix of of_xlate_tdm_slot_mask.
  ASoC: rcar: subnode tidyup for renesas,rsnd.txt
  ASoC: Remove name_prefix unset during DAI link init hack
  ALSA: hda - Inform the unexpectedly ignored pins by auto-parser
  ASoC: rcar: bugfix: it cares about the non-src case
  ARM: bockw: fixup SND_SOC_DAIFMT_CBx_CFx flags
  ASoC: pcm: Drop incorrect double/extra frees
  ASoC: mfld_machine: Fix compile error
  ...

22 files changed, 559 insertions, 50 deletions

diff --git a/Documentation/DocBook/writing-an-alsa-driver.tmpl b/Documentation/DocBook/writing-an-alsa-driver.tmpl
index 06741e925985..d0056a4e9c53 100644
--- a/Documentation/DocBook/writing-an-alsa-driver.tmpl
+++ b/Documentation/DocBook/writing-an-alsa-driver.tmpl
@@ -468,8 +468,6 @@
                   return err;
           }
 
-          snd_card_set_dev(card, &pci->dev);
-
           *rchip = chip;
           return 0;
   }
@@ -492,7 +490,8 @@
           }
 
           /* (2) */
-          err = snd_card_create(index[dev], id[dev], THIS_MODULE, 0, &card);
+          err = snd_card_new(&pci->dev, index[dev], id[dev], THIS_MODULE,
+                             0, &card);
           if (err < 0)
                   return err;
 
@@ -591,7 +590,8 @@
   struct snd_card *card;
   int err;
   ....
-  err = snd_card_create(index[dev], id[dev], THIS_MODULE, 0, &card);
+  err = snd_card_new(&pci->dev, index[dev], id[dev], THIS_MODULE,
+                     0, &card);
 ]]>
             </programlisting>
           </informalexample>
@@ -809,28 +809,34 @@
 
       <para>
         As mentioned above, to create a card instance, call
-      <function>snd_card_create()</function>.
+      <function>snd_card_new()</function>.
 
         <informalexample>
           <programlisting>
 <![CDATA[
   struct snd_card *card;
   int err;
-  err = snd_card_create(index, id, module, extra_size, &card);
+  err = snd_card_new(&pci->dev, index, id, module, extra_size, &card);
 ]]>
           </programlisting>
         </informalexample>
       </para>
 
       <para>
-        The function takes five arguments, the card-index number, the
-        id string, the module pointer (usually
+        The function takes six arguments: the parent device pointer,
+        the card-index number, the id string, the module pointer (usually
         <constant>THIS_MODULE</constant>),
         the size of extra-data space, and the pointer to return the
         card instance.  The extra_size argument is used to
         allocate card-&gt;private_data for the
         chip-specific data.  Note that these data
-        are allocated by <function>snd_card_create()</function>.
+        are allocated by <function>snd_card_new()</function>.
+      </para>
+
+      <para>
+	The first argument, the pointer of struct
+	<structname>device</structname>, specifies the parent device.
+	For PCI devices, typically &amp;pci-&gt; is passed there.
       </para>
     </section>
 
@@ -916,16 +922,16 @@
       </para>
 
       <section id="card-management-chip-specific-snd-card-new">
-        <title>1. Allocating via <function>snd_card_create()</function>.</title>
+        <title>1. Allocating via <function>snd_card_new()</function>.</title>
         <para>
           As mentioned above, you can pass the extra-data-length
-	  to the 4th argument of <function>snd_card_create()</function>, i.e.
+	  to the 5th argument of <function>snd_card_new()</function>, i.e.
 
           <informalexample>
             <programlisting>
 <![CDATA[
-  err = snd_card_create(index[dev], id[dev], THIS_MODULE,
-                        sizeof(struct mychip), &card);
+  err = snd_card_new(&pci->dev, index[dev], id[dev], THIS_MODULE,
+                     sizeof(struct mychip), &card);
 ]]>
             </programlisting>
           </informalexample>
@@ -954,7 +960,7 @@
 
         <para>
           After allocating a card instance via
-          <function>snd_card_create()</function> (with
+          <function>snd_card_new()</function> (with
           <constant>0</constant> on the 4th arg), call
           <function>kzalloc()</function>. 
 
@@ -963,7 +969,8 @@
 <![CDATA[
   struct snd_card *card;
   struct mychip *chip;
-  err = snd_card_create(index[dev], id[dev], THIS_MODULE, 0, &card);
+  err = snd_card_new(&pci->dev, index[dev], id[dev], THIS_MODULE,
+                     0, &card);
   .....
   chip = kzalloc(sizeof(*chip), GFP_KERNEL);
 ]]>
@@ -1170,8 +1177,6 @@
                   return err;
           }
 
-          snd_card_set_dev(card, &pci->dev);
-
           *rchip = chip;
           return 0;
   }        
@@ -1526,30 +1531,6 @@
 
     </section>
 
-    <section id="pci-resource-device-struct">
-      <title>Registration of Device Struct</title>
-      <para>
-	At some point, typically after calling <function>snd_device_new()</function>,
-	you need to register the struct <structname>device</structname> of the chip
-	you're handling for udev and co.  ALSA provides a macro for compatibility with
-	older kernels.  Simply call like the following:
-        <informalexample>
-          <programlisting>
-<![CDATA[
-  snd_card_set_dev(card, &pci->dev);
-]]>
-          </programlisting>
-        </informalexample>
-	so that it stores the PCI's device pointer to the card.  This will be
-	referred by ALSA core functions later when the devices are registered.
-      </para>
-      <para>
-	In the case of non-PCI, pass the proper device struct pointer of the BUS
-	instead.  (In the case of legacy ISA without PnP, you don't have to do
-	anything.)
-      </para>
-    </section>
-
     <section id="pci-resource-entries">
       <title>PCI Entries</title>
       <para>
@@ -5740,7 +5721,8 @@ struct _snd_pcm_runtime {
           struct mychip *chip;
           int err;
           ....
-          err = snd_card_create(index[dev], id[dev], THIS_MODULE, 0, &card);
+          err = snd_card_new(&pci->dev, index[dev], id[dev], THIS_MODULE,
+                             0, &card);
           ....
           chip = kzalloc(sizeof(*chip), GFP_KERNEL);
           ....
@@ -5752,7 +5734,7 @@ struct _snd_pcm_runtime {
       </informalexample>
 
 	When you created the chip data with
-	<function>snd_card_create()</function>, it's anyway accessible
+	<function>snd_card_new()</function>, it's anyway accessible
 	via <structfield>private_data</structfield> field.
 
       <informalexample>
@@ -5766,8 +5748,8 @@ struct _snd_pcm_runtime {
           struct mychip *chip;
           int err;
           ....
-          err = snd_card_create(index[dev], id[dev], THIS_MODULE,
-                                sizeof(struct mychip), &card);
+          err = snd_card_new(&pci->dev, index[dev], id[dev], THIS_MODULE,
+                             sizeof(struct mychip), &card);
           ....
           chip = card->private_data;
           ....
diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt
index 1a1ac2e560e9..f47e56bcf78d 100644
--- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt
+++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt
@@ -18,6 +18,7 @@ atmel,24c02		i2c serial eeprom  (24cxx)
 atmel,at97sc3204t	i2c trusted platform module (TPM)
 capella,cm32181		CM32181: Ambient Light Sensor
 catalyst,24c32		i2c serial eeprom
+cirrus,cs42l51		Cirrus Logic CS42L51 audio codec
 dallas,ds1307		64 x 8, Serial, I2C Real-Time Clock
 dallas,ds1338		I2C RTC with 56-Byte NV RAM
 dallas,ds1339		I2C Serial Real-Time Clock
diff --git a/Documentation/devicetree/bindings/misc/atmel-ssc.txt b/Documentation/devicetree/bindings/misc/atmel-ssc.txt
index 60960b2755f4..efc98ea1f23d 100644
--- a/Documentation/devicetree/bindings/misc/atmel-ssc.txt
+++ b/Documentation/devicetree/bindings/misc/atmel-ssc.txt
@@ -17,6 +17,14 @@ Required properties for devices compatible with "atmel,at91sam9g45-ssc":
   See Documentation/devicetree/bindings/dma/atmel-dma.txt for details.
 - dma-names: Must be "tx", "rx".
 
+Optional properties:
+  - atmel,clk-from-rk-pin: bool property.
+     - When SSC works in slave mode, according to the hardware design, the
+       clock can get from TK pin, and also can get from RK pin. So, add
+       this parameter to choose where the clock from.
+     - By default the clock is from TK pin, if the clock from RK pin, this
+       property is needed.
+
 Examples:
 - PDC transfer:
 ssc0: ssc@fffbc000 {
diff --git a/Documentation/devicetree/bindings/sound/armada-370db-audio.txt b/Documentation/devicetree/bindings/sound/armada-370db-audio.txt
new file mode 100644
index 000000000000..bf984d238620
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/armada-370db-audio.txt
@@ -0,0 +1,27 @@
+Device Tree bindings for the Armada 370 DB audio
+================================================
+
+These Device Tree bindings are used to describe the audio complex
+found on the Armada 370 DB platform.
+
+Mandatory properties:
+
+ * compatible: must be "marvell,a370db-audio"
+
+ * marvell,audio-controller: a phandle that points to the audio
+   controller of the Armada 370 SoC.
+
+ * marvell,audio-codec: a set of three phandles that points to:
+
+    1/ the analog audio codec connected to the Armada 370 SoC
+    2/ the S/PDIF transceiver
+    3/ the S/PDIF receiver
+
+Example:
+
+	sound {
+	      compatible = "marvell,a370db-audio";
+	      marvell,audio-controller = <&audio_controller>;
+	      marvell,audio-codec = <&audio_codec &spdif_out &spdif_in>;
+	      status = "okay";
+	};
diff --git a/Documentation/devicetree/bindings/sound/cs42xx8.txt b/Documentation/devicetree/bindings/sound/cs42xx8.txt
new file mode 100644
index 000000000000..f631fbca6284
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/cs42xx8.txt
@@ -0,0 +1,28 @@
+CS42448/CS42888 audio CODEC
+
+Required properties:
+
+  - compatible : must contain one of "cirrus,cs42448" and "cirrus,cs42888"
+
+  - reg : the I2C address of the device for I2C
+
+  - clocks : a list of phandles + clock-specifiers, one for each entry in
+    clock-names
+
+  - clock-names : must contain "mclk"
+
+  - VA-supply, VD-supply, VLS-supply, VLC-supply: power supplies for the device,
+    as covered in Documentation/devicetree/bindings/regulator/regulator.txt
+
+Example:
+
+codec: cs42888@48 {
+	compatible = "cirrus,cs42888";
+	reg = <0x48>;
+	clocks = <&codec_mclk 0>;
+	clock-names = "mclk";
+	VA-supply = <&reg_audio>;
+	VD-supply = <&reg_audio>;
+	VLS-supply = <&reg_audio>;
+	VLC-supply = <&reg_audio>;
+};
diff --git a/Documentation/devicetree/bindings/sound/da9055.txt b/Documentation/devicetree/bindings/sound/da9055.txt
new file mode 100644
index 000000000000..ed1b7cc6f249
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/da9055.txt
@@ -0,0 +1,22 @@
+* Dialog DA9055 Audio CODEC
+
+DA9055 provides Audio CODEC support (I2C only).
+
+The Audio CODEC device in DA9055 has it's own I2C address which is configurable,
+so the device is instantiated separately from the PMIC (MFD) device.
+
+For details on accompanying PMIC I2C device, see the following:
+Documentation/devicetree/bindings/mfd/da9055.txt
+
+Required properties:
+
+  - compatible: "dlg,da9055-codec"
+  - reg: Specifies the I2C slave address
+
+
+Example:
+
+	codec: da9055-codec@1a {
+		compatible = "dlg,da9055-codec";
+		reg = <0x1a>;
+	};
diff --git a/Documentation/devicetree/bindings/sound/davinci-evm-audio.txt b/Documentation/devicetree/bindings/sound/davinci-evm-audio.txt
index 865178d5cdf3..963e100514c2 100644
--- a/Documentation/devicetree/bindings/sound/davinci-evm-audio.txt
+++ b/Documentation/devicetree/bindings/sound/davinci-evm-audio.txt
@@ -5,12 +5,19 @@ Required properties:
 - ti,model : The user-visible name of this sound complex.
 - ti,audio-codec : The phandle of the TLV320AIC3x audio codec
 - ti,mcasp-controller : The phandle of the McASP controller
-- ti,codec-clock-rate : The Codec Clock rate (in Hz) applied to the Codec
 - ti,audio-routing : A list of the connections between audio components.
   Each entry is a pair of strings, the first being the connection's sink,
   the second being the connection's source. Valid names for sources and
   sinks are the codec's pins, and the jacks on the board:
 
+Optional properties:
+- ti,codec-clock-rate : The Codec Clock rate (in Hz) applied to the Codec.
+- clocks : Reference to the master clock
+- clock-names : The clock should be named "mclk"
+- Either codec-clock-rate or the codec-clock reference has to be defined. If
+  the both are defined the driver attempts to set referenced clock to the
+  defined rate and takes the rate from the clock reference.
+
   Board connectors:
 
   * Headphone Jack
diff --git a/Documentation/devicetree/bindings/sound/eukrea-tlv320.txt b/Documentation/devicetree/bindings/sound/eukrea-tlv320.txt
new file mode 100644
index 000000000000..0d7985c864af
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/eukrea-tlv320.txt
@@ -0,0 +1,21 @@
+Audio complex for Eukrea boards with tlv320aic23 codec.
+
+Required properties:
+- compatible : "eukrea,asoc-tlv320"
+- eukrea,model : The user-visible name of this sound complex.
+- ssi-controller : The phandle of the SSI controller.
+- fsl,mux-int-port : The internal port of the i.MX audio muxer (AUDMUX).
+- fsl,mux-ext-port : The external port of the i.MX audio muxer.
+
+Note: The AUDMUX port numbering should start at 1, which is consistent with
+hardware manual.
+
+Example:
+
+	sound {
+		compatible = "eukrea,asoc-tlv320";
+		eukrea,model = "imx51-eukrea-tlv320aic23";
+		ssi-controller = <&ssi2>;
+		fsl,mux-int-port = <2>;
+		fsl,mux-ext-port = <3>;
+	};
diff --git a/Documentation/devicetree/bindings/sound/fsl,esai.txt b/Documentation/devicetree/bindings/sound/fsl,esai.txt
index d7b99fa637b5..aeb8c4a0b88d 100644
--- a/Documentation/devicetree/bindings/sound/fsl,esai.txt
+++ b/Documentation/devicetree/bindings/sound/fsl,esai.txt
@@ -34,6 +34,10 @@ Required properties:
     that ESAI would work in the synchronous mode, which means all the settings
     for Receiving would be duplicated from Transmition related registers.
 
+  - big-endian : If this property is absent, the native endian mode will
+    be in use as default, or the big endian mode will be in use for all the
+    device registers.
+
 Example:
 
 esai: esai@02024000 {
@@ -46,5 +50,6 @@ esai: esai@02024000 {
 	dma-names = "rx", "tx";
 	fsl,fifo-depth = <128>;
 	fsl,esai-synchronous;
+	big-endian;
 	status = "disabled";
 };
diff --git a/Documentation/devicetree/bindings/sound/fsl,spdif.txt b/Documentation/devicetree/bindings/sound/fsl,spdif.txt
index f2ae335670f5..3e9e82c8eab3 100644
--- a/Documentation/devicetree/bindings/sound/fsl,spdif.txt
+++ b/Documentation/devicetree/bindings/sound/fsl,spdif.txt
@@ -29,6 +29,10 @@ Required properties:
 			can also be referred to TxClk_Source
 			bit of register SPDIF_STC.
 
+   - big-endian : If this property is absent, the native endian mode will
+   be in use as default, or the big endian mode will be in use for all the
+   device registers.
+
 Example:
 
 spdif: spdif@02004000 {
@@ -50,5 +54,6 @@ spdif: spdif@02004000 {
 		"rxtx5", "rxtx6",
 		"rxtx7";
 
+	big-endian;
 	status = "okay";
 };
diff --git a/Documentation/devicetree/bindings/sound/mvebu-audio.txt b/Documentation/devicetree/bindings/sound/mvebu-audio.txt
index f0062c5871b4..cb8c07c81ce4 100644
--- a/Documentation/devicetree/bindings/sound/mvebu-audio.txt
+++ b/Documentation/devicetree/bindings/sound/mvebu-audio.txt
@@ -5,6 +5,7 @@ Required properties:
 - compatible:
   "marvell,kirkwood-audio" for Kirkwood platforms
   "marvell,dove-audio" for Dove platforms
+  "marvell,armada370-audio" for Armada 370 platforms
 
 - reg: physical base address of the controller and length of memory mapped
   region.
diff --git a/Documentation/devicetree/bindings/sound/pcm512x.txt b/Documentation/devicetree/bindings/sound/pcm512x.txt
new file mode 100644
index 000000000000..faff75e64573
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/pcm512x.txt
@@ -0,0 +1,30 @@
+PCM512x audio CODECs
+
+These devices support both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+
+  - compatible : One of "ti,pcm5121" or "ti,pcm5122"
+
+  - reg : the I2C address of the device for I2C, the chip select
+          number for SPI.
+
+  - AVDD-supply, DVDD-supply, and CPVDD-supply : power supplies for the
+    device, as covered in bindings/regulator/regulator.txt
+
+Optional properties:
+
+  - clocks : A clock specifier for the clock connected as SCLK.  If this
+    is absent the device will be configured to clock from BCLK.
+
+Example:
+
+	pcm5122: pcm5122@4c {
+		compatible = "ti,pcm5122";
+		reg = <0x4c>;
+
+		AVDD-supply = <&reg_3v3_analog>;
+		DVDD-supply = <&reg_1v8>;
+		CPVDD-supply = <&reg_3v3>;
+	};
diff --git a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt
new file mode 100644
index 000000000000..a44e9179faf5
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt
@@ -0,0 +1,105 @@
+Renesas R-Car sound
+
+Required properties:
+- compatible			: "renesas,rcar_sound-gen1" if generation1
+				  "renesas,rcar_sound-gen2" if generation2
+- reg				: Should contain the register physical address.
+				  required register is
+				   SRU/ADG/SSI      if generation1
+				   SRU/ADG/SSIU/SSI if generation2
+- rcar_sound,ssi		: Should contain SSI feature.
+				  The number of SSI subnode should be same as HW.
+				  see below for detail.
+- rcar_sound,src		: Should contain SRC feature.
+				  The number of SRC subnode should be same as HW.
+				  see below for detail.
+- rcar_sound,dai		: DAI contents.
+				  The number of DAI subnode should be same as HW.
+				  see below for detail.
+
+SSI subnode properties:
+- interrupts			: Should contain SSI interrupt for PIO transfer
+- shared-pin			: if shared clock pin
+
+SRC subnode properties:
+no properties at this point
+
+DAI subnode properties:
+- playback			: list of playback modules
+- capture			: list of capture  modules
+
+Example:
+
+rcar_sound: rcar_sound@0xffd90000 {
+	#sound-dai-cells = <1>;
+	compatible = "renesas,rcar_sound-gen2";
+	reg =	<0 0xec500000 0 0x1000>, /* SCU */
+		<0 0xec5a0000 0 0x100>,  /* ADG */
+		<0 0xec540000 0 0x1000>, /* SSIU */
+		<0 0xec541000 0 0x1280>; /* SSI */
+
+	rcar_sound,src {
+		src0: src@0 { };
+		src1: src@1 { };
+		src2: src@2 { };
+		src3: src@3 { };
+		src4: src@4 { };
+		src5: src@5 { };
+		src6: src@6 { };
+		src7: src@7 { };
+		src8: src@8 { };
+		src9: src@9 { };
+	};
+
+	rcar_sound,ssi {
+		ssi0: ssi@0 {
+			interrupts = <0 370 IRQ_TYPE_LEVEL_HIGH>;
+		};
+		ssi1: ssi@1 {
+			interrupts = <0 371 IRQ_TYPE_LEVEL_HIGH>;
+		};
+		ssi2: ssi@2 {
+			interrupts = <0 372 IRQ_TYPE_LEVEL_HIGH>;
+		};
+		ssi3: ssi@3 {
+			interrupts = <0 373 IRQ_TYPE_LEVEL_HIGH>;
+		};
+		ssi4: ssi@4 {
+			interrupts = <0 374 IRQ_TYPE_LEVEL_HIGH>;
+		};
+		ssi5: ssi@5 {
+			interrupts = <0 375 IRQ_TYPE_LEVEL_HIGH>;
+		};
+		ssi6: ssi@6 {
+			interrupts = <0 376 IRQ_TYPE_LEVEL_HIGH>;
+		};
+		ssi7: ssi@7 {
+			interrupts = <0 377 IRQ_TYPE_LEVEL_HIGH>;
+		};
+		ssi8: ssi@8 {
+			interrupts = <0 378 IRQ_TYPE_LEVEL_HIGH>;
+		};
+		ssi9: ssi@9 {
+			interrupts = <0 379 IRQ_TYPE_LEVEL_HIGH>;
+		};
+	};
+
+	rcar_sound,dai {
+		dai0 {
+			playback = <&ssi5 &src5>;
+			capture  = <&ssi6>;
+		};
+		dai1 {
+			playback = <&ssi3>;
+		};
+		dai2 {
+			capture  = <&ssi4>;
+		};
+		dai3 {
+			playback = <&ssi7>;
+		};
+		dai4 {
+			capture  = <&ssi8>;
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/sound/simple-card.txt b/Documentation/devicetree/bindings/sound/simple-card.txt
index 19c84df5fffa..131aa2ad7f1a 100644
--- a/Documentation/devicetree/bindings/sound/simple-card.txt
+++ b/Documentation/devicetree/bindings/sound/simple-card.txt
@@ -8,16 +8,26 @@ Required properties:
 
 Optional properties:
 
+- simple-audio-card,name		: User specified audio sound card name, one string
+					  property.
 - simple-audio-card,format		: CPU/CODEC common audio format.
 					  "i2s", "right_j", "left_j" , "dsp_a"
 					  "dsp_b", "ac97", "pdm", "msb", "lsb"
+- simple-audio-card,widgets		: Please refer to widgets.txt.
 - simple-audio-card,routing		: A list of the connections between audio components.
 					  Each entry is a pair of strings, the first being the
 					  connection's sink, the second being the connection's
 					  source.
+- dai-tdm-slot-num			: Please refer to tdm-slot.txt.
+- dai-tdm-slot-width			: Please refer to tdm-slot.txt.
 
 Required subnodes:
 
+- simple-audio-card,dai-link		: container for the CPU and CODEC sub-nodes
+					  This container may be omitted when the
+					  card has only one DAI link.
+					  See the examples.
+
 - simple-audio-card,cpu			: CPU   sub-node
 - simple-audio-card,codec		: CODEC sub-node
 
@@ -38,15 +48,29 @@ Optional CPU/CODEC subnodes properties:
 					  clock node (= common clock), or "system-clock-frequency"
 					  (if system doens't support common clock)
 
-Example:
+Note:
+ * For 'format', 'frame-master', 'bitclock-master', 'bitclock-inversion' and
+   'frame-inversion', the simple card will use the settings of CODEC for both
+   CPU and CODEC sides as we need to keep the settings identical for both ends
+   of the link.
+
+Example 1 - single DAI link:
 
 sound {
 	compatible = "simple-audio-card";
+	simple-audio-card,name = "VF610-Tower-Sound-Card";
 	simple-audio-card,format = "left_j";
+	simple-audio-card,widgets =
+		"Microphone", "Microphone Jack",
+		"Headphone", "Headphone Jack",
+		"Speaker", "External Speaker";
 	simple-audio-card,routing =
-		"MIC_IN", "Mic Jack",
+		"MIC_IN", "Microphone Jack",
 		"Headphone Jack", "HP_OUT",
-		"Ext Spk", "LINE_OUT";
+		"External Speaker", "LINE_OUT";
+
+	dai-tdm-slot-num = <2>;
+	dai-tdm-slot-width = <8>;
 
 	simple-audio-card,cpu {
 		sound-dai = <&sh_fsi2 0>;
@@ -75,3 +99,38 @@ sh_fsi2: sh_fsi2@ec230000 {
 	interrupt-parent = <&gic>;
 	interrupts = <0 146 0x4>;
 };
+
+Example 2 - many DAI links:
+
+sound {
+	compatible = "simple-audio-card";
+	simple-audio-card,name = "Cubox Audio";
+	simple-audio-card,format = "i2s";
+
+	simple-audio-card,dai-link@0 {		/* I2S - HDMI */
+		simple-audio-card,cpu {
+			sound-dai = <&audio1 0>;
+		};
+		simple-audio-card,codec {
+			sound-dai = <&tda998x 0>;
+		};
+	};
+
+	simple-audio-card,dai-link@1 {		/* S/PDIF - HDMI */
+		simple-audio-card,cpu {
+			sound-dai = <&audio1 1>;
+		};
+		simple-audio-card,codec {
+			sound-dai = <&tda998x 1>;
+		};
+	};
+
+	simple-audio-card,dai-link@2 {		/* S/PDIF - S/PDIF */
+		simple-audio-card,cpu {
+			sound-dai = <&audio1 1>;
+		};
+		simple-audio-card,codec {
+			sound-dai = <&spdif_codec>;
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/sound/sirf-audio-codec.txt b/Documentation/devicetree/bindings/sound/sirf-audio-codec.txt
new file mode 100644
index 000000000000..062f5ec36f9b
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/sirf-audio-codec.txt
@@ -0,0 +1,17 @@
+SiRF internal audio CODEC
+
+Required properties:
+
+  - compatible : "sirf,atlas6-audio-codec" or "sirf,prima2-audio-codec"
+
+  - reg : the register address of the device.
+
+  - clocks: the clock of SiRF internal audio codec
+
+Example:
+
+audiocodec: audiocodec@b0040000 {
+	compatible = "sirf,atlas6-audio-codec";
+	reg = <0xb0040000 0x10000>;
+	clocks = <&clks 27>;
+};
diff --git a/Documentation/devicetree/bindings/sound/sirf-audio-port.txt b/Documentation/devicetree/bindings/sound/sirf-audio-port.txt
new file mode 100644
index 000000000000..1f66de3c8f00
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/sirf-audio-port.txt
@@ -0,0 +1,20 @@
+* SiRF SoC audio port
+
+Required properties:
+- compatible: "sirf,audio-port"
+- reg: Base address and size entries:
+- dmas: List of DMA controller phandle and DMA request line ordered pairs.
+- dma-names: Identifier string for each DMA request line in the dmas property.
+  These strings correspond 1:1 with the ordered pairs in dmas.
+
+  One of the DMA channels will be responsible for transmission (should be
+  named "tx") and one for reception (should be named "rx").
+
+Example:
+
+audioport: audioport@b0040000 {
+	compatible = "sirf,audio-port";
+	reg = <0xb0040000 0x10000>;
+	dmas = <&dmac1 3>, <&dmac1 8>;
+	dma-names = "rx", "tx";
+};
diff --git a/Documentation/devicetree/bindings/sound/sirf-audio.txt b/Documentation/devicetree/bindings/sound/sirf-audio.txt
new file mode 100644
index 000000000000..c88882ca3704
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/sirf-audio.txt
@@ -0,0 +1,41 @@
+* SiRF atlas6 and prima2 internal audio codec and port based audio setups
+
+Required properties:
+- compatible: "sirf,sirf-audio-card"
+- sirf,audio-platform: phandle for the platform node
+- sirf,audio-codec: phandle for the SiRF internal codec node
+
+Optional properties:
+- hp-pa-gpios: Need to be present if the board need control external
+  headphone amplifier.
+- spk-pa-gpios: Need to be present if the board need control external
+  speaker amplifier.
+- hp-switch-gpios: Need to be present if the board capable to detect jack
+  insertion, removal.
+
+Available audio endpoints for the audio-routing table:
+
+Board connectors:
+ * Headset Stereophone
+ * Ext Spk
+ * Line In
+ * Mic
+
+SiRF internal audio codec pins:
+ * HPOUTL
+ * HPOUTR
+ * SPKOUT
+ * Ext Mic
+ * Mic Bias
+
+Example:
+
+sound {
+		compatible = "sirf,sirf-audio-card";
+		sirf,audio-codec = <&audiocodec>;
+		sirf,audio-platform = <&audioport>;
+		hp-pa-gpios = <&gpio 44 0>;
+		spk-pa-gpios = <&gpio 46 0>;
+		hp-switch-gpios = <&gpio 45 0>;
+};
+
diff --git a/Documentation/devicetree/bindings/sound/tdm-slot.txt b/Documentation/devicetree/bindings/sound/tdm-slot.txt
new file mode 100644
index 000000000000..6a2c84247f91
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/tdm-slot.txt
@@ -0,0 +1,20 @@
+TDM slot:
+
+This specifies audio DAI's TDM slot.
+
+TDM slot properties:
+dai-tdm-slot-num : Number of slots in use.
+dai-tdm-slot-width :  Width in bits for each slot.
+
+For instance:
+	dai-tdm-slot-num = <2>;
+	dai-tdm-slot-width = <8>;
+
+And for each spcified driver, there could be one .of_xlate_tdm_slot_mask()
+to specify a explicit mapping of the channels and the slots. If it's absent
+the default snd_soc_of_xlate_tdm_slot_mask() will be used to generating the
+tx and rx masks.
+
+For snd_soc_of_xlate_tdm_slot_mask(), the tx and rx masks will use a 1 bit
+for an active slot as default, and the default active bits are at the LSB of
+the masks.
diff --git a/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt b/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt
new file mode 100644
index 000000000000..74c66dee3e14
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt
@@ -0,0 +1,61 @@
+Texas Instruments - tlv320aic31xx Codec module
+
+The tlv320aic31xx serial control bus communicates through I2C protocols
+
+Required properties:
+
+- compatible - "string" - One of:
+    "ti,tlv320aic310x" - Generic TLV320AIC31xx with mono speaker amp
+    "ti,tlv320aic311x" - Generic TLV320AIC31xx with stereo speaker amp
+    "ti,tlv320aic3100" - TLV320AIC3100 (mono speaker amp, no MiniDSP)
+    "ti,tlv320aic3110" - TLV320AIC3110 (stereo speaker amp, no MiniDSP)
+    "ti,tlv320aic3120" - TLV320AIC3120 (mono speaker amp, MiniDSP)
+    "ti,tlv320aic3111" - TLV320AIC3111 (stereo speaker amp, MiniDSP)
+
+- reg - <int> -  I2C slave address
+
+
+Optional properties:
+
+- gpio-reset - gpio pin number used for codec reset
+- ai31xx-micbias-vg - MicBias Voltage setting
+        1 or MICBIAS_2_0V - MICBIAS output is powered to 2.0V
+        2 or MICBIAS_2_5V - MICBIAS output is powered to 2.5V
+        3 or MICBIAS_AVDD - MICBIAS output is connected to AVDD
+	If this node is not mentioned or if the value is unknown, then
+	micbias	is set to 2.0V.
+- HPVDD-supply, SPRVDD-supply, SPLVDD-supply, AVDD-supply, IOVDD-supply,
+  DVDD-supply : power supplies for the device as covered in
+  Documentation/devicetree/bindings/regulator/regulator.txt
+
+CODEC output pins:
+  * HPL
+  * HPR
+  * SPL, devices with stereo speaker amp
+  * SPR, devices with stereo speaker amp
+  * SPK, devices with mono speaker amp
+  * MICBIAS
+
+CODEC input pins:
+  * MIC1LP
+  * MIC1RP
+  * MIC1LM
+
+The pins can be used in referring sound node's audio-routing property.
+
+Example:
+#include <dt-bindings/sound/tlv320aic31xx-micbias.h>
+
+tlv320aic31xx: tlv320aic31xx@18 {
+	compatible = "ti,tlv320aic311x";
+	reg = <0x18>;
+
+	ai31xx-micbias-vg = <MICBIAS_OFF>;
+
+	HPVDD-supply = <&regulator>;
+	SPRVDD-supply = <&regulator>;
+	SPLVDD-supply = <&regulator>;
+	AVDD-supply = <&regulator>;
+	IOVDD-supply = <&regulator>;
+	DVDD-supply = <&regulator>;
+};
diff --git a/Documentation/devicetree/bindings/sound/tlv320aic32x4.txt b/Documentation/devicetree/bindings/sound/tlv320aic32x4.txt
new file mode 100644
index 000000000000..5e2741af27be
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/tlv320aic32x4.txt
@@ -0,0 +1,30 @@
+Texas Instruments - tlv320aic32x4 Codec module
+
+The tlv320aic32x4 serial control bus communicates through I2C protocols
+
+Required properties:
+ - compatible: Should be "ti,tlv320aic32x4"
+ - reg: I2C slave address
+ - supply-*: Required supply regulators are:
+    "iov" - digital IO power supply
+    "ldoin" - LDO power supply
+    "dv" - Digital core power supply
+    "av" - Analog core power supply
+    If you supply ldoin, dv and av are optional. Otherwise they are required
+   See regulator/regulator.txt for more information about the detailed binding
+   format.
+
+Optional properties:
+ - reset-gpios: Reset-GPIO phandle with args as described in gpio/gpio.txt
+ - clocks/clock-names: Clock named 'mclk' for the master clock of the codec.
+   See clock/clock-bindings.txt for information about the detailed format.
+
+
+Example:
+
+codec: tlv320aic32x4@18 {
+	compatible = "ti,tlv320aic32x4";
+	reg = <0x18>;
+	clocks = <&clks 201>;
+	clock-names = "mclk";
+};
diff --git a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt
index 9d8ea14db490..5e6040c2c2e9 100644
--- a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt
+++ b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt
@@ -6,7 +6,6 @@ Required properties:
 
 - compatible - "string" - One of:
     "ti,tlv320aic3x" - Generic TLV320AIC3x device
-    "ti,tlv320aic32x4" - TLV320AIC32x4
     "ti,tlv320aic33" - TLV320AIC33
     "ti,tlv320aic3007" - TLV320AIC3007
     "ti,tlv320aic3106" - TLV320AIC3106
diff --git a/Documentation/devicetree/bindings/sound/widgets.txt b/Documentation/devicetree/bindings/sound/widgets.txt
new file mode 100644
index 000000000000..b6de5ba3b2de
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/widgets.txt
@@ -0,0 +1,20 @@
+Widgets:
+
+This mainly specifies audio off-codec DAPM widgets.
+
+Each entry is a pair of strings in DT:
+
+	"template-wname", "user-supplied-wname"
+
+The "template-wname" being the template widget name and currently includes:
+"Microphone", "Line", "Headphone" and "Speaker".
+
+The "user-supplied-wname" being the user specified widget name.
+
+For instance:
+	simple-audio-widgets =
+		"Microphone", "Microphone Jack",
+		"Line", "Line In Jack",
+		"Line", "Line Out Jack",
+		"Headphone", "Headphone Jack",
+		"Speaker", "Speaker External";