Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC cleanups from Olof Johansson:
 "A large cleanup branch this release, with a healthy 10k negative line
  delta.

  Most of this is removal of legacy (non-DT) support of shmobile
  platforms.  There is also removal of two non-DT platforms on OMAP, and
  the plat-samsung directory is cleaned out by moving most of the
  previously shared-location-but-not-actually-shared files from there to
  the appropriate mach directories instead.

  There are other sets of changes in here as well:

   - Rob Herring removed use of set_irq_flags under all platforms and
     moved to genirq alternatives

   - a series of timer API conversions to set-state interface

   - ep93xx, nomadik and ux500 cleanups from Linus Walleij

   - __init annotation fixes from Nicolas Pitre

   + a bunch of other changes that all add up to a nice set of cleanups"

* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (108 commits)
  ARM/fb: ep93xx: switch framebuffer to use modedb only
  ARM: gemini: Setup timer3 as free running timer
  ARM: gemini: Use timer1 for clockevent
  ARM: gemini: Add missing register definitions for gemini timer
  ARM: ep93xx/timer: Migrate to new 'set-state' interface
  ARM: nomadik: push accelerometer down to boards
  ARM: nomadik: move l2x0 setup to device tree
  ARM: nomadik: selectively enable UART0 on boards
  ARM: nomadik: move hog code to use DT hogs
  ARM: shmobile: Fix mismerges
  ARM: ux500: simplify secondary CPU boot
  ARM: SAMSUNG: remove keypad-core header in plat-samsung
  ARM: SAMSUNG: local watchdog-reset header in mach-s3c64xx
  ARM: SAMSUNG: local onenand-core header in mach-s3c64xx
  ARM: SAMSUNG: local irq-uart header in mach-s3c64xx
  ARM: SAMSUNG: local backlight header in mach-s3c64xx
  ARM: SAMSUNG: local ata-core header in mach-s3c64xx
  ARM: SAMSUNG: local regs-usb-hsotg-phy header in mach-s3c64xx
  ARM: SAMSUNG: local spi-core header in mach-s3c24xx
  ARM: SAMSUNG: local nand-core header in mach-s3c24xx
  ...

4 files changed, 74 insertions, 36 deletions

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 246473a244f6..917aa318929d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -501,11 +501,8 @@ dtb-$(CONFIG_ARCH_S5PV210) += \
 	s5pv210-smdkv210.dtb \
 	s5pv210-torbreck.dtb
 dtb-$(CONFIG_ARCH_SHMOBILE_LEGACY) += \
-	r8a7740-armadillo800eva.dtb \
 	r8a7778-bockw.dtb \
-	r8a7778-bockw-reference.dtb \
-	r8a7779-marzen.dtb \
-	sh73a0-kzm9g.dtb
+	r8a7778-bockw-reference.dtb
 dtb-$(CONFIG_ARCH_SHMOBILE_MULTI) += \
 	emev2-kzm9d.dtb \
 	r7s72100-genmai.dtb \
diff --git a/arch/arm/boot/dts/ste-nomadik-nhk15.dts b/arch/arm/boot/dts/ste-nomadik-nhk15.dts
index 3d25dba143a5..4a21c6492dbb 100644
--- a/arch/arm/boot/dts/ste-nomadik-nhk15.dts
+++ b/arch/arm/boot/dts/ste-nomadik-nhk15.dts
@@ -17,12 +17,22 @@
 	};
 
 	aliases {
+		serial0 = &uart0;
 		serial1 = &uart1;
 		stmpe-i2c0 = &stmpe0;
 		stmpe-i2c1 = &stmpe1;
 	};
 
 	pinctrl {
+		uart0 {
+			uart0_nhk_mode: uart0_mux {
+				u0_default_mux {
+					function = "u0";
+					groups = "u0txrx_a_1", "u0ctsrts_a_1";
+				};
+			};
+		};
+
 		stmpe2401_1 {
 			stmpe2401_1_nhk_mode: stmpe2401_1_nhk {
 				nhk_cfg1 {
@@ -73,6 +83,11 @@
 	};
 
 	i2c0 {
+		lis3lv02dl@1d {
+			/* Accelerometer */
+			compatible = "st,lis3lv02dl-accel";
+			reg = <0x1d>;
+		};
 		stmpe0: stmpe2401@43 {
 			compatible = "st,stmpe2401";
 			reg = <0x43>;
@@ -131,22 +146,30 @@
 				#gpio-cells = <2>;
 				interrupt-controller;
 				#interrupt-cells = <2>;
+				/*
+				 * This will turn off SATA so that MMC/SD
+				 * can thrive
+				 */
+				mmcsd-gpio {
+					gpio-hog;
+					gpios = <2 0x0>;
+					output-low;
+					line-name = "SATA EN";
+				};
 			};
 		};
 	};
 
 	amba {
+		/* Activate RX/TX and CTS/RTS on UART 0 */
+		uart0: uart@101fd000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart0_nhk_mode>;
+			status = "okay";
+		};
 		mmcsd: sdi@101f6000 {
 			cd-gpios = <&stmpe_gpio44 7 GPIO_ACTIVE_LOW>;
 			wp-gpios = <&stmpe_gpio44 18 GPIO_ACTIVE_HIGH>;
 		};
 	};
-
-	/* Custom board node with GPIO pins to active etc */
-	usb-s8815 {
-		/* This will turn off SATA so that MMC/SD can thrive */
-		mmcsd-gpio {
-			gpios = <&stmpe_gpio44 2 0x1>;
-		};
-	};
 };
diff --git a/arch/arm/boot/dts/ste-nomadik-s8815.dts b/arch/arm/boot/dts/ste-nomadik-s8815.dts
index 3c140d05f796..35282c0105c6 100644
--- a/arch/arm/boot/dts/ste-nomadik-s8815.dts
+++ b/arch/arm/boot/dts/ste-nomadik-s8815.dts
@@ -16,9 +16,20 @@
 	};
 
 	aliases {
+		serial0 = &uart0;
 		serial1 = &uart1;
 	};
 
+	gpio3: gpio@101e7000 {
+		/* This hog will bias the MMC/SD card detect line */
+		mmcsd-gpio {
+			gpio-hog;
+			gpios = <16 0x0>;
+			output-low;
+			line-name = "card detect bias";
+		};
+	};
+
 	src@101e0000 {
 		/* These chrystal drivers are not used on this board */
 		disable-sxtalo;
@@ -30,6 +41,15 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&cd_default_mode>;
 
+		uart0 {
+			/* Only use RX/TX pins */
+			uart0_s8815_mode: uart0_mux {
+				u0_default_mux {
+					function = "u0";
+					groups = "u0txrx_a_1";
+				};
+			};
+		};
 		mmcsd-cd {
 			cd_default_mode: cd_default {
 				cd_default_cfg1 {
@@ -85,6 +105,14 @@
 		};
 	};
 
+	i2c1 {
+		lis3lv02dl@1d {
+			/* Accelerometer */
+			compatible = "st,lis3lv02dl-accel";
+			reg = <0x1d>;
+		};
+	};
+
 	/* GPIO I2C connected to the USB portions of the STw4811 only */
 	gpio-i2c {
 		compatible = "i2c-gpio";
@@ -102,21 +130,19 @@
 	};
 
 
-	/* Configure card detect for the uSD slot */
 	amba {
+		/* Activate RXTX on UART 0 */
+		uart0: uart@101fd000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart0_s8815_mode>;
+			status = "okay";
+		};
+		/* Configure card detect for the uSD slot */
 		mmcsd: sdi@101f6000 {
 			cd-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>;
 		};
 	};
 
-	/* Custom board node with GPIO pins to active etc */
-	usb-s8815 {
-		/* This will bias the MMC/SD card detect line */
-		mmcsd-gpio {
-			gpios = <&gpio3 16 0x1>;
-		};
-	};
-
 	/* The user LED on the board is set up to be used for heartbeat */
 	leds {
 		compatible = "gpio-leds";
diff --git a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi b/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
index ef794a33b4dc..176e332fc0bd 100644
--- a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
+++ b/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
@@ -21,6 +21,13 @@
 		interrupts = <30>;
 		cache-unified;
 		cache-level = <2>;
+		cache-size = <131072>;
+		cache-sets = <512>;
+		cache-line-size = <32>;
+		/* At full speed latency must be >=2 */
+		arm,tag-latency = <2>;
+		arm,data-latency = <2 2>;
+		arm,dirty-latency = <2>;
 	};
 
 	mtu0: mtu@101e2000 {
@@ -97,14 +104,6 @@
 	pinctrl {
 		compatible = "stericsson,stn8815-pinctrl";
 		/* Pin configurations */
-		uart0 {
-			uart0_default_mux: uart0_mux {
-				u0_default_mux {
-					function = "u0";
-					groups = "u0_a_1";
-				};
-			};
-		};
 		uart1 {
 			uart1_default_mux: uart1_mux {
 				u1_default_mux {
@@ -721,11 +720,6 @@
 			   compatible = "st,stw5095";
 			   reg = <0x1a>;
 		};
-		lis3lv02dl@1d {
-			/* Accelerometer */
-			compatible = "st,lis3lv02dl-accel";
-			reg = <0x1d>;
-		};
 	};
 
 	amba {
@@ -755,8 +749,6 @@
 			interrupts = <12>;
 			clocks = <&uart0clk>, <&pclkuart0>;
 			clock-names = "uartclk", "apb_pclk";
-			pinctrl-names = "default";
-			pinctrl-0 = <&uart0_default_mux>;
 			status = "disabled";
 		};