Merge branch 'gic' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64 into next/cleanup

* 'gic' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
  irqchip: gic: Perform the gic_secondary_init() call via CPU notifier
  irqchip: gic: Call handle_bad_irq() directly
  arm: Move chained_irq_(enter|exit) to a generic file
  arm: Move the set_handle_irq and handle_arch_irq declarations to asm/irq.h
  + Linux 3.9-rc3

Signed-off-by: Olof Johansson <olof@lixom.net>

82 files changed, 123 insertions, 285 deletions

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 5bfd584929c8..eaae82a182ed 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -49,7 +49,7 @@ config ARM
 	select HAVE_REGS_AND_STACK_ACCESS_API
 	select HAVE_SYSCALL_TRACEPOINTS
 	select HAVE_UID16
-	select HAVE_VIRT_TO_BUS
+	select VIRT_TO_BUS
 	select KTIME_SCALAR
 	select PERF_USE_VMALLOC
 	select RTC_LIB
@@ -556,7 +556,6 @@ config ARCH_IXP4XX
 config ARCH_DOVE
 	bool "Marvell Dove"
 	select ARCH_REQUIRE_GPIOLIB
-	select COMMON_CLK_DOVE
 	select CPU_V7
 	select GENERIC_CLOCKEVENTS
 	select MIGHT_HAVE_PCI
@@ -1658,13 +1657,16 @@ config LOCAL_TIMERS
 	  accounting to be spread across the timer interval, preventing a
 	  "thundering herd" at every timer tick.
 
+# The GPIO number here must be sorted by descending number. In case of
+# a multiplatform kernel, we just want the highest value required by the
+# selected platforms.
 config ARCH_NR_GPIO
 	int
 	default 1024 if ARCH_SHMOBILE || ARCH_TEGRA
-	default 355 if ARCH_U8500
-	default 264 if MACH_H4700
 	default 512 if SOC_OMAP5
+	default 355 if ARCH_U8500
 	default 288 if ARCH_VT8500 || ARCH_SUNXI
+	default 264 if MACH_H4700
 	default 0
 	help
 	  Maximum number of GPIOs in the system.
@@ -1888,8 +1890,9 @@ config XEN_DOM0
 
 config XEN
 	bool "Xen guest support on ARM (EXPERIMENTAL)"
-	depends on ARM && OF
+	depends on ARM && AEABI && OF
 	depends on CPU_V7 && !CPU_V6
+	depends on !GENERIC_ATOMIC64
 	help
 	  Say Y if you want to run Linux in a Virtual Machine on Xen on ARM.
 
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index acddddac7ee4..ecfcdba2d17c 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -492,7 +492,7 @@ config DEBUG_IMX_UART_PORT
 						DEBUG_IMX31_UART || \
 						DEBUG_IMX35_UART || \
 						DEBUG_IMX51_UART || \
-						DEBUG_IMX50_IMX53_UART || \
+						DEBUG_IMX53_UART || \
 						DEBUG_IMX6Q_UART
 	default 1
 	help
diff --git a/arch/arm/boot/Makefile b/arch/arm/boot/Makefile
index 71768b8a1ab9..84aa2caf07ed 100644
--- a/arch/arm/boot/Makefile
+++ b/arch/arm/boot/Makefile
@@ -115,4 +115,4 @@ i:
 	$(CONFIG_SHELL) $(srctree)/$(src)/install.sh $(KERNELRELEASE) \
 	$(obj)/Image System.map "$(INSTALL_PATH)"
 
-subdir-	    := bootp compressed
+subdir-	    := bootp compressed dts
diff --git a/arch/arm/boot/dts/armada-370-rd.dts b/arch/arm/boot/dts/armada-370-rd.dts
index f8e4855bc9a5..070bba4f2585 100644
--- a/arch/arm/boot/dts/armada-370-rd.dts
+++ b/arch/arm/boot/dts/armada-370-rd.dts
@@ -64,5 +64,13 @@
 			status = "okay";
 			/* No CD or WP GPIOs */
 		};
+
+		usb@d0050000 {
+			status = "okay";
+		};
+
+		usb@d0051000 {
+			status = "okay";
+		};
 	};
 };
diff --git a/arch/arm/boot/dts/armada-370-xp.dtsi b/arch/arm/boot/dts/armada-370-xp.dtsi
index 6f1acc75e155..5b708208b607 100644
--- a/arch/arm/boot/dts/armada-370-xp.dtsi
+++ b/arch/arm/boot/dts/armada-370-xp.dtsi
@@ -31,7 +31,6 @@
 	mpic: interrupt-controller@d0020000 {
 	      compatible = "marvell,mpic";
 	      #interrupt-cells = <1>;
-	      #address-cells = <1>;
 	      #size-cells = <1>;
 	      interrupt-controller;
 	};
@@ -54,7 +53,7 @@
 				reg = <0xd0012000 0x100>;
 				reg-shift = <2>;
 				interrupts = <41>;
-				reg-io-width = <4>;
+				reg-io-width = <1>;
 				status = "disabled";
 		};
 		serial@d0012100 {
@@ -62,7 +61,7 @@
 				reg = <0xd0012100 0x100>;
 				reg-shift = <2>;
 				interrupts = <42>;
-				reg-io-width = <4>;
+				reg-io-width = <1>;
 				status = "disabled";
 		};
 
diff --git a/arch/arm/boot/dts/armada-xp.dtsi b/arch/arm/boot/dts/armada-xp.dtsi
index 1443949c165e..ca00d8326c87 100644
--- a/arch/arm/boot/dts/armada-xp.dtsi
+++ b/arch/arm/boot/dts/armada-xp.dtsi
@@ -46,7 +46,7 @@
 				reg = <0xd0012200 0x100>;
 				reg-shift = <2>;
 				interrupts = <43>;
-				reg-io-width = <4>;
+				reg-io-width = <1>;
 				status = "disabled";
 		};
 		serial@d0012300 {
@@ -54,7 +54,7 @@
 				reg = <0xd0012300 0x100>;
 				reg-shift = <2>;
 				interrupts = <44>;
-				reg-io-width = <4>;
+				reg-io-width = <1>;
 				status = "disabled";
 		};
 
diff --git a/arch/arm/boot/dts/bcm2835.dtsi b/arch/arm/boot/dts/bcm2835.dtsi
index 4bf2a8774aa7..7e0481e2441a 100644
--- a/arch/arm/boot/dts/bcm2835.dtsi
+++ b/arch/arm/boot/dts/bcm2835.dtsi
@@ -105,7 +105,7 @@
 			compatible = "fixed-clock";
 			reg = <1>;
 			#clock-cells = <0>;
-			clock-frequency = <150000000>;
+			clock-frequency = <250000000>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/dbx5x0.dtsi b/arch/arm/boot/dts/dbx5x0.dtsi
index 69140ba99f46..9de93096601a 100644
--- a/arch/arm/boot/dts/dbx5x0.dtsi
+++ b/arch/arm/boot/dts/dbx5x0.dtsi
@@ -319,9 +319,8 @@
 				};
 			};
 
-			ab8500@5 {
+			ab8500 {
 				compatible = "stericsson,ab8500";
-				reg = <5>; /* mailbox 5 is i2c */
 				interrupt-parent = <&intc>;
 				interrupts = <0 40 0x4>;
 				interrupt-controller;
diff --git a/arch/arm/boot/dts/dove.dtsi b/arch/arm/boot/dts/dove.dtsi
index 67dbe20868a2..f7509cafc377 100644
--- a/arch/arm/boot/dts/dove.dtsi
+++ b/arch/arm/boot/dts/dove.dtsi
@@ -197,6 +197,11 @@
 			status = "disabled";
 		};
 
+		rtc@d8500 {
+			compatible = "marvell,orion-rtc";
+			reg = <0xd8500 0x20>;
+		};
+
 		crypto: crypto@30000 {
 			compatible = "marvell,orion-crypto";
 			reg = <0x30000 0x10000>,
diff --git a/arch/arm/boot/dts/href.dtsi b/arch/arm/boot/dts/href.dtsi
index 592fb9dc35bd..379128eb9d98 100644
--- a/arch/arm/boot/dts/href.dtsi
+++ b/arch/arm/boot/dts/href.dtsi
@@ -221,7 +221,7 @@
 				};
 			};
 
-			ab8500@5 {
+			ab8500 {
 				ab8500-regulators {
 					ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
 						regulator-name = "V-DISPLAY";
diff --git a/arch/arm/boot/dts/hrefv60plus.dts b/arch/arm/boot/dts/hrefv60plus.dts
index 55f4191a626e..2b587a74b813 100644
--- a/arch/arm/boot/dts/hrefv60plus.dts
+++ b/arch/arm/boot/dts/hrefv60plus.dts
@@ -158,7 +158,7 @@
 				};
 			};
 
-			ab8500@5 {
+			ab8500 {
 				ab8500-regulators {
 					ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
 						regulator-name = "V-DISPLAY";
diff --git a/arch/arm/boot/dts/imx53-mba53.dts b/arch/arm/boot/dts/imx53-mba53.dts
index e54fffd48369..468c0a1d48d9 100644
--- a/arch/arm/boot/dts/imx53-mba53.dts
+++ b/arch/arm/boot/dts/imx53-mba53.dts
@@ -42,10 +42,9 @@
 			fsl,pins = <689 0x10000		/* DISP1_DRDY	*/
 				    482 0x10000		/* DISP1_HSYNC	*/
 				    489 0x10000		/* DISP1_VSYNC	*/
-				    684 0x10000		/* DISP1_DAT_0	*/
 				    515 0x10000		/* DISP1_DAT_22	*/
 				    523 0x10000		/* DISP1_DAT_23	*/
-				    543 0x10000		/* DISP1_DAT_21	*/
+				    545 0x10000		/* DISP1_DAT_21	*/
 				    553 0x10000		/* DISP1_DAT_20	*/
 				    558 0x10000		/* DISP1_DAT_19	*/
 				    564 0x10000		/* DISP1_DAT_18	*/
diff --git a/arch/arm/boot/dts/kirkwood-dns320.dts b/arch/arm/boot/dts/kirkwood-dns320.dts
index 5bb0bf39d3b8..c9c44b2f62d7 100644
--- a/arch/arm/boot/dts/kirkwood-dns320.dts
+++ b/arch/arm/boot/dts/kirkwood-dns320.dts
@@ -42,12 +42,10 @@
 
 	ocp@f1000000 {
 		serial@12000 {
-			clock-frequency = <166666667>;
 			status = "okay";
 		};
 
 		serial@12100 {
-			clock-frequency = <166666667>;
 			status = "okay";
 		};
 	};
diff --git a/arch/arm/boot/dts/kirkwood-dns325.dts b/arch/arm/boot/dts/kirkwood-dns325.dts
index d430713ea9b9..e4e4930dc5cf 100644
--- a/arch/arm/boot/dts/kirkwood-dns325.dts
+++ b/arch/arm/boot/dts/kirkwood-dns325.dts
@@ -50,7 +50,6 @@
 			};
 		};
 		serial@12000 {
-			clock-frequency = <200000000>;
 			status = "okay";
 		};
 	};
diff --git a/arch/arm/boot/dts/kirkwood-dockstar.dts b/arch/arm/boot/dts/kirkwood-dockstar.dts
index 2e3dd34e21a5..0196cf6b0ef2 100644
--- a/arch/arm/boot/dts/kirkwood-dockstar.dts
+++ b/arch/arm/boot/dts/kirkwood-dockstar.dts
@@ -37,7 +37,6 @@
 			};
 		};
 		serial@12000 {
-			clock-frequency = <200000000>;
 			status = "ok";
 		};
 
diff --git a/arch/arm/boot/dts/kirkwood-dreamplug.dts b/arch/arm/boot/dts/kirkwood-dreamplug.dts
index ef2d8c705709..289e51d86372 100644
--- a/arch/arm/boot/dts/kirkwood-dreamplug.dts
+++ b/arch/arm/boot/dts/kirkwood-dreamplug.dts
@@ -38,7 +38,6 @@
 			};
 		};
 		serial@12000 {
-			clock-frequency = <200000000>;
 			status = "ok";
 		};
 
diff --git a/arch/arm/boot/dts/kirkwood-goflexnet.dts b/arch/arm/boot/dts/kirkwood-goflexnet.dts
index 1b133e0c566e..bd83b8fc7c83 100644
--- a/arch/arm/boot/dts/kirkwood-goflexnet.dts
+++ b/arch/arm/boot/dts/kirkwood-goflexnet.dts
@@ -73,7 +73,6 @@
 			};
 		};
 		serial@12000 {
-			clock-frequency = <200000000>;
 			status = "ok";
 		};
 
diff --git a/arch/arm/boot/dts/kirkwood-ib62x0.dts b/arch/arm/boot/dts/kirkwood-ib62x0.dts
index 71902da33d63..5335b1aa8601 100644
--- a/arch/arm/boot/dts/kirkwood-ib62x0.dts
+++ b/arch/arm/boot/dts/kirkwood-ib62x0.dts
@@ -51,7 +51,6 @@
 			};
 		};
 		serial@12000 {
-			clock-frequency = <200000000>;
 			status = "okay";
 		};
 
diff --git a/arch/arm/boot/dts/kirkwood-iconnect.dts b/arch/arm/boot/dts/kirkwood-iconnect.dts
index 504f16be8b54..12ccf74ac3c4 100644
--- a/arch/arm/boot/dts/kirkwood-iconnect.dts
+++ b/arch/arm/boot/dts/kirkwood-iconnect.dts
@@ -78,7 +78,6 @@
 			};
 		};
 		serial@12000 {
-			clock-frequency = <200000000>;
 			status = "ok";
 		};
 
diff --git a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
index 6cae4599c4b3..93c3afbef9ee 100644
--- a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
+++ b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
@@ -115,7 +115,6 @@
 		};
 
 		serial@12000 {
-			clock-frequency = <200000000>;
 			status = "ok";
 		};
 
diff --git a/arch/arm/boot/dts/kirkwood-km_kirkwood.dts b/arch/arm/boot/dts/kirkwood-km_kirkwood.dts
index 8db3123ac80f..5bbd0542cdd3 100644
--- a/arch/arm/boot/dts/kirkwood-km_kirkwood.dts
+++ b/arch/arm/boot/dts/kirkwood-km_kirkwood.dts
@@ -34,7 +34,6 @@
 		};
 
 		serial@12000 {
-			clock-frequency = <200000000>;
 			status = "ok";
 		};
 
diff --git a/arch/arm/boot/dts/kirkwood-lschlv2.dts b/arch/arm/boot/dts/kirkwood-lschlv2.dts
index 9510c9ea666c..9f55d95f35f5 100644
--- a/arch/arm/boot/dts/kirkwood-lschlv2.dts
+++ b/arch/arm/boot/dts/kirkwood-lschlv2.dts
@@ -13,7 +13,6 @@
 
 	ocp@f1000000 {
 		serial@12000 {
-			clock-frequency = <166666667>;
 			status = "okay";
 		};
 	};
diff --git a/arch/arm/boot/dts/kirkwood-lsxhl.dts b/arch/arm/boot/dts/kirkwood-lsxhl.dts
index 739019c4cba9..5c84c118ed8d 100644
--- a/arch/arm/boot/dts/kirkwood-lsxhl.dts
+++ b/arch/arm/boot/dts/kirkwood-lsxhl.dts
@@ -13,7 +13,6 @@
 
 	ocp@f1000000 {
 		serial@12000 {
-			clock-frequency = <200000000>;
 			status = "okay";
 		};
 	};
diff --git a/arch/arm/boot/dts/kirkwood-mplcec4.dts b/arch/arm/boot/dts/kirkwood-mplcec4.dts
index 662dfd81b1ce..758824118a9a 100644
--- a/arch/arm/boot/dts/kirkwood-mplcec4.dts
+++ b/arch/arm/boot/dts/kirkwood-mplcec4.dts
@@ -90,7 +90,6 @@
                 };
 
                 serial@12000 {
-                        clock-frequency = <200000000>;
                         status = "ok";
                 };
 
diff --git a/arch/arm/boot/dts/kirkwood-ns2-common.dtsi b/arch/arm/boot/dts/kirkwood-ns2-common.dtsi
index e8e7ecef1650..6affd924fe11 100644
--- a/arch/arm/boot/dts/kirkwood-ns2-common.dtsi
+++ b/arch/arm/boot/dts/kirkwood-ns2-common.dtsi
@@ -23,7 +23,6 @@
 		};
 
 		serial@12000 {
-			clock-frequency = <166666667>;
 			status = "okay";
 		};
 
diff --git a/arch/arm/boot/dts/kirkwood-nsa310.dts b/arch/arm/boot/dts/kirkwood-nsa310.dts
index 3a178cf708d7..a7412b937a8a 100644
--- a/arch/arm/boot/dts/kirkwood-nsa310.dts
+++ b/arch/arm/boot/dts/kirkwood-nsa310.dts
@@ -117,7 +117,6 @@
 		};
 
 		serial@12000 {
-			clock-frequency = <200000000>;
 			status = "ok";
 		};
 
diff --git a/arch/arm/boot/dts/kirkwood-openblocks_a6.dts b/arch/arm/boot/dts/kirkwood-openblocks_a6.dts
index ede7fe0d7a87..d27f7245f8e7 100644
--- a/arch/arm/boot/dts/kirkwood-openblocks_a6.dts
+++ b/arch/arm/boot/dts/kirkwood-openblocks_a6.dts
@@ -18,12 +18,10 @@
 
 	ocp@f1000000 {
 		serial@12000 {
-			clock-frequency = <200000000>;
 			status = "ok";
 		};
 
 		serial@12100 {
-			clock-frequency = <200000000>;
 			status = "ok";
 		};
 
diff --git a/arch/arm/boot/dts/kirkwood-topkick.dts b/arch/arm/boot/dts/kirkwood-topkick.dts
index 842ff95d60df..66eb45b00b25 100644
--- a/arch/arm/boot/dts/kirkwood-topkick.dts
+++ b/arch/arm/boot/dts/kirkwood-topkick.dts
@@ -108,7 +108,6 @@
 		};
 
 		serial@12000 {
-			clock-frequency = <200000000>;
 			status = "ok";
 		};
 
diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/kirkwood.dtsi
index 2c738d9dc82a..fada7e6d24d8 100644
--- a/arch/arm/boot/dts/kirkwood.dtsi
+++ b/arch/arm/boot/dts/kirkwood.dtsi
@@ -38,6 +38,7 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 			interrupts = <35>, <36>, <37>, <38>;
+			clocks = <&gate_clk 7>;
 		};
 
 		gpio1: gpio@10140 {
@@ -49,6 +50,7 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 			interrupts = <39>, <40>, <41>;
+			clocks = <&gate_clk 7>;
 		};
 
 		serial@12000 {
@@ -57,7 +59,6 @@
 			reg-shift = <2>;
 			interrupts = <33>;
 			clocks = <&gate_clk 7>;
-			/* set clock-frequency in board dts */
 			status = "disabled";
 		};
 
@@ -67,7 +68,6 @@
 			reg-shift = <2>;
 			interrupts = <34>;
 			clocks = <&gate_clk 7>;
-			/* set clock-frequency in board dts */
 			status = "disabled";
 		};
 
@@ -75,6 +75,7 @@
 			compatible = "marvell,kirkwood-rtc", "marvell,orion-rtc";
 			reg = <0x10300 0x20>;
 			interrupts = <53>;
+			clocks = <&gate_clk 7>;
 		};
 
 		spi@10600 {
diff --git a/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts b/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts
index 5a3a58b7e18f..0077fc8510b7 100644
--- a/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts
+++ b/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts
@@ -11,7 +11,7 @@
 
 / {
 	model = "LaCie Ethernet Disk mini V2";
-	compatible = "lacie,ethernet-disk-mini-v2", "marvell-orion5x-88f5182", "marvell,orion5x";
+	compatible = "lacie,ethernet-disk-mini-v2", "marvell,orion5x-88f5182", "marvell,orion5x";
 
 	memory {
 		reg = <0x00000000 0x4000000>; /* 64 MB */
diff --git a/arch/arm/boot/dts/snowball.dts b/arch/arm/boot/dts/snowball.dts
index 27f31a5fa494..d3ec32f6b790 100644
--- a/arch/arm/boot/dts/snowball.dts
+++ b/arch/arm/boot/dts/snowball.dts
@@ -298,7 +298,7 @@
 				};
 			};
 
-			ab8500@5 {
+			ab8500 {
 				ab8500-regulators {
 					ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
 						regulator-name = "V-DISPLAY";
diff --git a/arch/arm/boot/dts/socfpga.dtsi b/arch/arm/boot/dts/socfpga.dtsi
index 936d2306e7e1..7e8769bd5977 100644
--- a/arch/arm/boot/dts/socfpga.dtsi
+++ b/arch/arm/boot/dts/socfpga.dtsi
@@ -75,6 +75,9 @@
 				compatible = "arm,pl330", "arm,primecell";
 				reg = <0xffe01000 0x1000>;
 				interrupts = <0 180 4>;
+				#dma-cells = <1>;
+				#dma-channels = <8>;
+				#dma-requests = <32>;
 			};
 		};
 
diff --git a/arch/arm/boot/dts/tegra20.dtsi b/arch/arm/boot/dts/tegra20.dtsi
index 9a428931d042..48d00a099ce3 100644
--- a/arch/arm/boot/dts/tegra20.dtsi
+++ b/arch/arm/boot/dts/tegra20.dtsi
@@ -118,6 +118,7 @@
 		compatible = "arm,cortex-a9-twd-timer";
 		reg = <0x50040600 0x20>;
 		interrupts = <1 13 0x304>;
+		clocks = <&tegra_car 132>;
 	};
 
 	intc: interrupt-controller {
diff --git a/arch/arm/boot/dts/tegra30.dtsi b/arch/arm/boot/dts/tegra30.dtsi
index 767803e1fd55..9d87a3ffe998 100644
--- a/arch/arm/boot/dts/tegra30.dtsi
+++ b/arch/arm/boot/dts/tegra30.dtsi
@@ -119,6 +119,7 @@
 		compatible = "arm,cortex-a9-twd-timer";
 		reg = <0x50040600 0x20>;
 		interrupts = <1 13 0xf04>;
+		clocks = <&tegra_car 214>;
 	};
 
 	intc: interrupt-controller {
diff --git a/arch/arm/configs/mxs_defconfig b/arch/arm/configs/mxs_defconfig
index fbbc5bb022d5..6a99e30f81d2 100644
--- a/arch/arm/configs/mxs_defconfig
+++ b/arch/arm/configs/mxs_defconfig
@@ -116,6 +116,7 @@ CONFIG_SND_SOC=y
 CONFIG_SND_MXS_SOC=y
 CONFIG_SND_SOC_MXS_SGTL5000=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_CHIPIDEA=y
 CONFIG_USB_CHIPIDEA_HOST=y
 CONFIG_USB_STORAGE=y
diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig
index b16bae2c9a60..bd07864f14a0 100644
--- a/arch/arm/configs/omap2plus_defconfig
+++ b/arch/arm/configs/omap2plus_defconfig
@@ -126,6 +126,8 @@ CONFIG_INPUT_MISC=y
 CONFIG_INPUT_TWL4030_PWRBUTTON=y
 CONFIG_VT_HW_CONSOLE_BINDING=y
 # CONFIG_LEGACY_PTYS is not set
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
 CONFIG_SERIAL_8250_NR_UARTS=32
 CONFIG_SERIAL_8250_EXTENDED=y
 CONFIG_SERIAL_8250_MANY_PORTS=y
diff --git a/arch/arm/include/asm/irq.h b/arch/arm/include/asm/irq.h
index 35c21c375d81..53c15dec7af6 100644
--- a/arch/arm/include/asm/irq.h
+++ b/arch/arm/include/asm/irq.h
@@ -30,6 +30,11 @@ extern void asm_do_IRQ(unsigned int, struct pt_regs *);
 void handle_IRQ(unsigned int, struct pt_regs *);
 void init_IRQ(void);
 
+#ifdef CONFIG_MULTI_IRQ_HANDLER
+extern void (*handle_arch_irq)(struct pt_regs *);
+extern void set_handle_irq(void (*handle_irq)(struct pt_regs *));
+#endif
+
 #endif
 
 #endif
diff --git a/arch/arm/include/asm/mach/irq.h b/arch/arm/include/asm/mach/irq.h
index 18c883023339..2092ee1e1300 100644
--- a/arch/arm/include/asm/mach/irq.h
+++ b/arch/arm/include/asm/mach/irq.h
@@ -20,11 +20,6 @@ struct seq_file;
 extern void init_FIQ(int);
 extern int show_fiq_list(struct seq_file *, int);
 
-#ifdef CONFIG_MULTI_IRQ_HANDLER
-extern void (*handle_arch_irq)(struct pt_regs *);
-extern void set_handle_irq(void (*handle_irq)(struct pt_regs *));
-#endif
-
 /*
  * This is for easy migration, but should be changed in the source
  */
@@ -35,35 +30,4 @@ do {							\
 	raw_spin_unlock(&desc->lock);			\
 } while(0)
 
-#ifndef __ASSEMBLY__
-/*
- * Entry/exit functions for chained handlers where the primary IRQ chip
- * may implement either fasteoi or level-trigger flow control.
- */
-static inline void chained_irq_enter(struct irq_chip *chip,
-				     struct irq_desc *desc)
-{
-	/* FastEOI controllers require no action on entry. */
-	if (chip->irq_eoi)
-		return;
-
-	if (chip->irq_mask_ack) {
-		chip->irq_mask_ack(&desc->irq_data);
-	} else {
-		chip->irq_mask(&desc->irq_data);
-		if (chip->irq_ack)
-			chip->irq_ack(&desc->irq_data);
-	}
-}
-
-static inline void chained_irq_exit(struct irq_chip *chip,
-				    struct irq_desc *desc)
-{
-	if (chip->irq_eoi)
-		chip->irq_eoi(&desc->irq_data);
-	else
-		chip->irq_unmask(&desc->irq_data);
-}
-#endif
-
 #endif
diff --git a/arch/arm/include/asm/xen/events.h b/arch/arm/include/asm/xen/events.h
index 5c27696de14f..8b1f37bfeeec 100644
--- a/arch/arm/include/asm/xen/events.h
+++ b/arch/arm/include/asm/xen/events.h
@@ -2,6 +2,7 @@
 #define _ASM_ARM_XEN_EVENTS_H
 
 #include <asm/ptrace.h>
+#include <asm/atomic.h>
 
 enum ipi_vector {
 	XEN_PLACEHOLDER_VECTOR,
@@ -15,26 +16,8 @@ static inline int xen_irqs_disabled(struct pt_regs *regs)
 	return raw_irqs_disabled_flags(regs->ARM_cpsr);
 }
 
-/*
- * We cannot use xchg because it does not support 8-byte
- * values. However it is safe to use {ldr,dtd}exd directly because all
- * platforms which Xen can run on support those instructions.
- */
-static inline xen_ulong_t xchg_xen_ulong(xen_ulong_t *ptr, xen_ulong_t val)
-{
-	xen_ulong_t oldval;
-	unsigned int tmp;
-
-	wmb();
-	asm volatile("@ xchg_xen_ulong\n"
-		"1:     ldrexd  %0, %H0, [%3]\n"
-		"       strexd  %1, %2, %H2, [%3]\n"
-		"       teq     %1, #0\n"
-		"       bne     1b"
-		: "=&r" (oldval), "=&r" (tmp)
-		: "r" (val), "r" (ptr)
-		: "memory", "cc");
-	return oldval;
-}
+#define xchg_xen_ulong(ptr, val) atomic64_xchg(container_of((ptr),	\
+							    atomic64_t,	\
+							    counter), (val))
 
 #endif /* _ASM_ARM_XEN_EVENTS_H */
diff --git a/arch/arm/mach-at91/board-foxg20.c b/arch/arm/mach-at91/board-foxg20.c
index 2ea7059b840b..c20a870ea9c9 100644
--- a/arch/arm/mach-at91/board-foxg20.c
+++ b/arch/arm/mach-at91/board-foxg20.c
@@ -176,6 +176,7 @@ static struct w1_gpio_platform_data w1_gpio_pdata = {
 	/* If you choose to use a pin other than PB16 it needs to be 3.3V */
 	.pin		= AT91_PIN_PB16,
 	.is_open_drain  = 1,
+	.ext_pullup_enable_pin	= -EINVAL,
 };
 
 static struct platform_device w1_device = {
diff --git a/arch/arm/mach-at91/board-stamp9g20.c b/arch/arm/mach-at91/board-stamp9g20.c
index a033b8df9fb2..869cbecf00b7 100644
--- a/arch/arm/mach-at91/board-stamp9g20.c
+++ b/arch/arm/mach-at91/board-stamp9g20.c
@@ -188,6 +188,7 @@ static struct spi_board_info portuxg20_spi_devices[] = {
 static struct w1_gpio_platform_data w1_gpio_pdata = {
 	.pin		= AT91_PIN_PA29,
 	.is_open_drain	= 1,
+	.ext_pullup_enable_pin	= -EINVAL,
 };
 
 static struct platform_device w1_device = {
diff --git a/arch/arm/mach-at91/gpio.c b/arch/arm/mach-at91/gpio.c
index c5d7e1e9d757..a5afcf76550e 100644
--- a/arch/arm/mach-at91/gpio.c
+++ b/arch/arm/mach-at91/gpio.c
@@ -22,10 +22,9 @@
 #include <linux/module.h>
 #include <linux/io.h>
 #include <linux/irqdomain.h>
+#include <linux/irqchip/chained_irq.h>
 #include <linux/of_address.h>
 
-#include <asm/mach/irq.h>
-
 #include <mach/hardware.h>
 #include <mach/at91_pio.h>
 
diff --git a/arch/arm/mach-exynos/common.c b/arch/arm/mach-exynos/common.c
index d63d399c7bae..7bc0f9aa8b33 100644
--- a/arch/arm/mach-exynos/common.c
+++ b/arch/arm/mach-exynos/common.c
@@ -26,6 +26,7 @@
 #include <linux/irqchip.h>
 #include <linux/of_address.h>
 #include <linux/irqchip/arm-gic.h>
+#include <linux/irqchip/chained_irq.h>
 
 #include <asm/proc-fns.h>
 #include <asm/exception.h>
diff --git a/arch/arm/mach-exynos/platsmp.c b/arch/arm/mach-exynos/platsmp.c
index 60f7c5be057d..95e04bd5813f 100644
--- a/arch/arm/mach-exynos/platsmp.c
+++ b/arch/arm/mach-exynos/platsmp.c
@@ -20,7 +20,6 @@
 #include <linux/jiffies.h>
 #include <linux/smp.h>
 #include <linux/io.h>
-#include <linux/irqchip/arm-gic.h>
 
 #include <asm/cacheflush.h>
 #include <asm/smp_plat.h>
@@ -76,13 +75,6 @@ static DEFINE_SPINLOCK(boot_lock);
 static void __cpuinit exynos_secondary_init(unsigned int cpu)
 {
 	/*
-	 * if any interrupts are already enabled for the primary
-	 * core (e.g. timer irq), then they will not have been enabled
-	 * for us: do so
-	 */
-	gic_secondary_init(0);
-
-	/*
 	 * let the primary processor know we're out of the
 	 * pen, then head off into the C entry point
 	 */
diff --git a/arch/arm/mach-highbank/platsmp.c b/arch/arm/mach-highbank/platsmp.c
index 8797a7001720..a984573e0d02 100644
--- a/arch/arm/mach-highbank/platsmp.c
+++ b/arch/arm/mach-highbank/platsmp.c
@@ -17,7 +17,6 @@
 #include <linux/init.h>
 #include <linux/smp.h>
 #include <linux/io.h>
-#include <linux/irqchip/arm-gic.h>
 
 #include <asm/smp_scu.h>
 
@@ -25,11 +24,6 @@
 
 extern void secondary_startup(void);
 
-static void __cpuinit highbank_secondary_init(unsigned int cpu)
-{
-	gic_secondary_init(0);
-}
-
 static int __cpuinit highbank_boot_secondary(unsigned int cpu, struct task_struct *idle)
 {
 	highbank_set_cpu_jump(cpu, secondary_startup);
@@ -67,7 +61,6 @@ static void __init highbank_smp_prepare_cpus(unsigned int max_cpus)
 struct smp_operations highbank_smp_ops __initdata = {
 	.smp_init_cpus		= highbank_smp_init_cpus,
 	.smp_prepare_cpus	= highbank_smp_prepare_cpus,
-	.smp_secondary_init	= highbank_secondary_init,
 	.smp_boot_secondary	= highbank_boot_secondary,
 #ifdef CONFIG_HOTPLUG_CPU
 	.cpu_die		= highbank_cpu_die,
diff --git a/arch/arm/mach-imx/clk-imx6q.c b/arch/arm/mach-imx/clk-imx6q.c
index 7b025ee528a5..2f9ff93a4e61 100644
--- a/arch/arm/mach-imx/clk-imx6q.c
+++ b/arch/arm/mach-imx/clk-imx6q.c
@@ -172,7 +172,7 @@ static struct clk *clk[clk_max];
 static struct clk_onecell_data clk_data;
 
 static enum mx6q_clks const clks_init_on[] __initconst = {
-	mmdc_ch0_axi, rom,
+	mmdc_ch0_axi, rom, pll1_sys,
 };
 
 static struct clk_div_table clk_enet_ref_table[] = {
diff --git a/arch/arm/mach-imx/headsmp.S b/arch/arm/mach-imx/headsmp.S
index 921fc1555854..a58c8b0527cc 100644
--- a/arch/arm/mach-imx/headsmp.S
+++ b/arch/arm/mach-imx/headsmp.S
@@ -26,16 +26,16 @@ ENDPROC(v7_secondary_startup)
 
 #ifdef CONFIG_PM
 /*
- * The following code is located into the .data section.  This is to
- * allow phys_l2x0_saved_regs to be accessed with a relative load
- * as we are running on physical address here.
+ * The following code must assume it is running from physical address
+ * where absolute virtual addresses to the data section have to be
+ * turned into relative ones.
  */
-	.data
-	.align
 
 #ifdef CONFIG_CACHE_L2X0
 	.macro	pl310_resume
-	ldr	r2, phys_l2x0_saved_regs
+	adr	r0, l2x0_saved_regs_offset
+	ldr	r2, [r0]
+	add	r2, r2, r0
 	ldr	r0, [r2, #L2X0_R_PHY_BASE]	@ get physical base of l2x0
 	ldr	r1, [r2, #L2X0_R_AUX_CTRL]	@ get aux_ctrl value
 	str	r1, [r0, #L2X0_AUX_CTRL]	@ restore aux_ctrl
@@ -43,9 +43,9 @@ ENDPROC(v7_secondary_startup)
 	str	r1, [r0, #L2X0_CTRL]		@ re-enable L2
 	.endm
 
-	.globl	phys_l2x0_saved_regs
-phys_l2x0_saved_regs:
-        .long   0
+l2x0_saved_regs_offset:
+	.word	l2x0_saved_regs - .
+
 #else
 	.macro	pl310_resume
 	.endm
diff --git a/arch/arm/mach-imx/platsmp.c b/arch/arm/mach-imx/platsmp.c
index 7c0b03f67b05..77e9a25ed0f6 100644
--- a/arch/arm/mach-imx/platsmp.c
+++ b/arch/arm/mach-imx/platsmp.c
@@ -12,7 +12,6 @@
 
 #include <linux/init.h>
 #include <linux/smp.h>
-#include <linux/irqchip/arm-gic.h>
 #include <asm/page.h>
 #include <asm/smp_scu.h>
 #include <asm/mach/map.h>
@@ -52,16 +51,6 @@ void imx_scu_standby_enable(void)
 	writel_relaxed(val, scu_base);
 }
 
-static void __cpuinit imx_secondary_init(unsigned int cpu)
-{
-	/*
-	 * if any interrupts are already enabled for the primary
-	 * core (e.g. timer irq), then they will not have been enabled
-	 * for us: do so
-	 */
-	gic_secondary_init(0);
-}
-
 static int __cpuinit imx_boot_secondary(unsigned int cpu, struct task_struct *idle)
 {
 	imx_set_cpu_jump(cpu, v7_secondary_startup);
@@ -96,7 +85,6 @@ static void __init imx_smp_prepare_cpus(unsigned int max_cpus)
 struct smp_operations  imx_smp_ops __initdata = {
 	.smp_init_cpus		= imx_smp_init_cpus,
 	.smp_prepare_cpus	= imx_smp_prepare_cpus,
-	.smp_secondary_init	= imx_secondary_init,
 	.smp_boot_secondary	= imx_boot_secondary,
 #ifdef CONFIG_HOTPLUG_CPU
 	.cpu_die		= imx_cpu_die,
diff --git a/arch/arm/mach-imx/pm-imx6q.c b/arch/arm/mach-imx/pm-imx6q.c
index ee42d20cba19..5faba7a3c95f 100644
--- a/arch/arm/mach-imx/pm-imx6q.c
+++ b/arch/arm/mach-imx/pm-imx6q.c
@@ -22,8 +22,6 @@
 #include "common.h"
 #include "hardware.h"
 
-extern unsigned long phys_l2x0_saved_regs;
-
 static int imx6q_suspend_finish(unsigned long val)
 {
 	cpu_do_idle();
@@ -57,18 +55,5 @@ static const struct platform_suspend_ops imx6q_pm_ops = {
 
 void __init imx6q_pm_init(void)
 {
-	/*
-	 * The l2x0 core code provides an infrastucture to save and restore
-	 * l2x0 registers across suspend/resume cycle.  But because imx6q
-	 * retains L2 content during suspend and needs to resume L2 before
-	 * MMU is enabled, it can only utilize register saving support and
-	 * have to take care of restoring on its own.  So we save physical
-	 * address of the data structure used by l2x0 core to save registers,
-	 * and later restore the necessary ones in imx6q resume entry.
-	 */
-#ifdef CONFIG_CACHE_L2X0
-	phys_l2x0_saved_regs = __pa(&l2x0_saved_regs);
-#endif
-
 	suspend_set_ops(&imx6q_pm_ops);
 }
diff --git a/arch/arm/mach-ixp4xx/vulcan-setup.c b/arch/arm/mach-ixp4xx/vulcan-setup.c
index d42730a1d4ab..d599e354ca57 100644
--- a/arch/arm/mach-ixp4xx/vulcan-setup.c
+++ b/arch/arm/mach-ixp4xx/vulcan-setup.c
@@ -163,6 +163,7 @@ static struct platform_device vulcan_max6369 = {
 
 static struct w1_gpio_platform_data vulcan_w1_gpio_pdata = {
 	.pin			= 14,
+	.ext_pullup_enable_pin	= -EINVAL,
 };
 
 static struct platform_device vulcan_w1_gpio = {
diff --git a/arch/arm/mach-kirkwood/board-dt.c b/arch/arm/mach-kirkwood/board-dt.c
index 2e73e9d53f70..d367aa6b47bb 100644
--- a/arch/arm/mach-kirkwood/board-dt.c
+++ b/arch/arm/mach-kirkwood/board-dt.c
@@ -41,16 +41,12 @@ static void __init kirkwood_legacy_clk_init(void)
 
 	struct device_node *np = of_find_compatible_node(
 		NULL, NULL, "marvell,kirkwood-gating-clock");
-
 	struct of_phandle_args clkspec;
+	struct clk *clk;
 
 	clkspec.np = np;
 	clkspec.args_count = 1;
 
-	clkspec.args[0] = CGC_BIT_GE0;
-	orion_clkdev_add(NULL, "mv643xx_eth_port.0",
-			 of_clk_get_from_provider(&clkspec));
-
 	clkspec.args[0] = CGC_BIT_PEX0;
 	orion_clkdev_add("0", "pcie",
 			 of_clk_get_from_provider(&clkspec));
@@ -59,9 +55,24 @@ static void __init kirkwood_legacy_clk_init(void)
 	orion_clkdev_add("1", "pcie",
 			 of_clk_get_from_provider(&clkspec));
 
-	clkspec.args[0] = CGC_BIT_GE1;
-	orion_clkdev_add(NULL, "mv643xx_eth_port.1",
+	clkspec.args[0] = CGC_BIT_SDIO;
+	orion_clkdev_add(NULL, "mvsdio",
 			 of_clk_get_from_provider(&clkspec));
+
+	/*
+	 * The ethernet interfaces forget the MAC address assigned by
+	 * u-boot if the clocks are turned off. Until proper DT support
+	 * is available we always enable them for now.
+	 */
+	clkspec.args[0] = CGC_BIT_GE0;
+	clk = of_clk_get_from_provider(&clkspec);
+	orion_clkdev_add(NULL, "mv643xx_eth_port.0", clk);
+	clk_prepare_enable(clk);
+
+	clkspec.args[0] = CGC_BIT_GE1;
+	clk = of_clk_get_from_provider(&clkspec);
+	orion_clkdev_add(NULL, "mv643xx_eth_port.1", clk);
+	clk_prepare_enable(clk);
 }
 
 static void __init kirkwood_of_clk_init(void)
diff --git a/arch/arm/mach-msm/platsmp.c b/arch/arm/mach-msm/platsmp.c
index 42932865416a..00cdb0a5dac8 100644
--- a/arch/arm/mach-msm/platsmp.c
+++ b/arch/arm/mach-msm/platsmp.c
@@ -15,7 +15,6 @@
 #include <linux/jiffies.h>
 #include <linux/smp.h>
 #include <linux/io.h>
-#include <linux/irqchip/arm-gic.h>
 
 #include <asm/cacheflush.h>
 #include <asm/cputype.h>
@@ -42,13 +41,6 @@ static inline int get_core_count(void)
 static void __cpuinit msm_secondary_init(unsigned int cpu)
 {
 	/*
-	 * if any interrupts are already enabled for the primary
-	 * core (e.g. timer irq), then they will not have been enabled
-	 * for us: do so
-	 */
-	gic_secondary_init(0);
-
-	/*
 	 * let the primary processor know we're out of the
 	 * pen, then head off into the C entry point
 	 */
diff --git a/arch/arm/mach-mxs/icoll.c b/arch/arm/mach-mxs/icoll.c
index 8fb23af154b3..e26eeba46598 100644
--- a/arch/arm/mach-mxs/icoll.c
+++ b/arch/arm/mach-mxs/icoll.c
@@ -100,7 +100,7 @@ static struct irq_domain_ops icoll_irq_domain_ops = {
 	.xlate = irq_domain_xlate_onecell,
 };
 
-void __init icoll_of_init(struct device_node *np,
+static void __init icoll_of_init(struct device_node *np,
 			  struct device_node *interrupt_parent)
 {
 	/*
diff --git a/arch/arm/mach-mxs/mach-mxs.c b/arch/arm/mach-mxs/mach-mxs.c
index 052186713347..3218f1f2c0e0 100644
--- a/arch/arm/mach-mxs/mach-mxs.c
+++ b/arch/arm/mach-mxs/mach-mxs.c
@@ -402,17 +402,17 @@ static void __init cfa10049_init(void)
 {
 	enable_clk_enet_out();
 	update_fec_mac_prop(OUI_CRYSTALFONTZ);
+
+	mxsfb_pdata.mode_list = cfa10049_video_modes;
+	mxsfb_pdata.mode_count = ARRAY_SIZE(cfa10049_video_modes);
+	mxsfb_pdata.default_bpp = 32;
+	mxsfb_pdata.ld_intf_width = STMLCDIF_18BIT;
 }
 
 static void __init cfa10037_init(void)
 {
 	enable_clk_enet_out();
 	update_fec_mac_prop(OUI_CRYSTALFONTZ);
-
-	mxsfb_pdata.mode_list = cfa10049_video_modes;
-	mxsfb_pdata.mode_count = ARRAY_SIZE(cfa10049_video_modes);
-	mxsfb_pdata.default_bpp = 32;
-	mxsfb_pdata.ld_intf_width = STMLCDIF_18BIT;
 }
 
 static void __init apf28_init(void)
diff --git a/arch/arm/mach-mxs/mm.c b/arch/arm/mach-mxs/mm.c
index a4294aa9f301..e63b7d87acbd 100644
--- a/arch/arm/mach-mxs/mm.c
+++ b/arch/arm/mach-mxs/mm.c
@@ -18,6 +18,7 @@
 
 #include <mach/mx23.h>
 #include <mach/mx28.h>
+#include <mach/common.h>
 
 /*
  * Define the MX23 memory map.
diff --git a/arch/arm/mach-mxs/ocotp.c b/arch/arm/mach-mxs/ocotp.c
index 54add60f94c9..1dff46703753 100644
--- a/arch/arm/mach-mxs/ocotp.c
+++ b/arch/arm/mach-mxs/ocotp.c
@@ -19,6 +19,7 @@
 #include <asm/processor.h>	/* for cpu_relax() */
 
 #include <mach/mxs.h>
+#include <mach/common.h>
 
 #define OCOTP_WORD_OFFSET		0x20
 #define OCOTP_WORD_COUNT		0x20
diff --git a/arch/arm/mach-omap1/common.h b/arch/arm/mach-omap1/common.h
index fb18831e88aa..14f7e9920479 100644
--- a/arch/arm/mach-omap1/common.h
+++ b/arch/arm/mach-omap1/common.h
@@ -31,6 +31,8 @@
 
 #include <plat/i2c.h>
 
+#include <mach/irqs.h>
+
 #if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
 void omap7xx_map_io(void);
 #else
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 49ac3dfebef9..8111cd9ff3e5 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -311,9 +311,6 @@ config MACH_OMAP_ZOOM2
 	default y
 	select OMAP_PACKAGE_CBB
 	select REGULATOR_FIXED_VOLTAGE if REGULATOR
-	select SERIAL_8250
-	select SERIAL_8250_CONSOLE
-	select SERIAL_CORE_CONSOLE
 
 config MACH_OMAP_ZOOM3
 	bool "OMAP3630 Zoom3 board"
@@ -321,9 +318,6 @@ config MACH_OMAP_ZOOM3
 	default y
 	select OMAP_PACKAGE_CBP
 	select REGULATOR_FIXED_VOLTAGE if REGULATOR
-	select SERIAL_8250
-	select SERIAL_8250_CONSOLE
-	select SERIAL_CORE_CONSOLE
 
 config MACH_CM_T35
 	bool "CompuLab CM-T35/CM-T3730 modules"
diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c
index 0274ff7a2a2b..e54a48060198 100644
--- a/arch/arm/mach-omap2/board-generic.c
+++ b/arch/arm/mach-omap2/board-generic.c
@@ -102,6 +102,7 @@ DT_MACHINE_START(OMAP3_DT, "Generic OMAP3 (Flattened Device Tree)")
 	.init_irq	= omap_intc_of_init,
 	.handle_irq	= omap3_intc_handle_irq,
 	.init_machine	= omap_generic_init,
+	.init_late	= omap3_init_late,
 	.init_time	= omap3_sync32k_timer_init,
 	.dt_compat	= omap3_boards_compat,
 	.restart	= omap3xxx_restart,
@@ -119,6 +120,7 @@ DT_MACHINE_START(OMAP3_GP_DT, "Generic OMAP3-GP (Flattened Device Tree)")
 	.init_irq	= omap_intc_of_init,
 	.handle_irq	= omap3_intc_handle_irq,
 	.init_machine	= omap_generic_init,
+	.init_late	= omap3_init_late,
 	.init_time	= omap3_secure_sync32k_timer_init,
 	.dt_compat	= omap3_gp_boards_compat,
 	.restart	= omap3xxx_restart,
diff --git a/arch/arm/mach-omap2/board-rx51.c b/arch/arm/mach-omap2/board-rx51.c
index f7c4616cbb60..d2ea68ea678a 100644
--- a/arch/arm/mach-omap2/board-rx51.c
+++ b/arch/arm/mach-omap2/board-rx51.c
@@ -17,6 +17,7 @@
 #include <linux/io.h>
 #include <linux/gpio.h>
 #include <linux/leds.h>
+#include <linux/usb/phy.h>
 #include <linux/usb/musb.h>
 #include <linux/platform_data/spi-omap2-mcspi.h>
 
@@ -98,6 +99,7 @@ static void __init rx51_init(void)
 	sdrc_params = nokia_get_sdram_timings();
 	omap_sdrc_init(sdrc_params, sdrc_params);
 
+	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
 	usb_musb_init(&musb_board_data);
 	rx51_peripherals_init();
 
diff --git a/arch/arm/mach-omap2/common.h b/arch/arm/mach-omap2/common.h
index 0a6b9c7a63da..40f4a03d728f 100644
--- a/arch/arm/mach-omap2/common.h
+++ b/arch/arm/mach-omap2/common.h
@@ -108,7 +108,6 @@ void omap35xx_init_late(void);
 void omap3630_init_late(void);
 void am35xx_init_late(void);
 void ti81xx_init_late(void);
-void omap4430_init_late(void);
 int omap2_common_pm_late_init(void);
 
 #if defined(CONFIG_SOC_OMAP2420) || defined(CONFIG_SOC_OMAP2430)
diff --git a/arch/arm/mach-omap2/gpmc.c b/arch/arm/mach-omap2/gpmc.c
index e4b16c8efe8b..410e1bac7815 100644
--- a/arch/arm/mach-omap2/gpmc.c
+++ b/arch/arm/mach-omap2/gpmc.c
@@ -1122,9 +1122,6 @@ int gpmc_calc_timings(struct gpmc_timings *gpmc_t,
 	/* TODO: remove, see function definition */
 	gpmc_convert_ps_to_ns(gpmc_t);
 
-	/* Now the GPMC is initialised, unreserve the chip-selects */
-	gpmc_cs_map = 0;
-
 	return 0;
 }
 
@@ -1383,6 +1380,9 @@ static int gpmc_probe(struct platform_device *pdev)
 	if (IS_ERR_VALUE(gpmc_setup_irq()))
 		dev_warn(gpmc_dev, "gpmc_setup_irq failed\n");
 
+	/* Now the GPMC is initialised, unreserve the chip-selects */
+	gpmc_cs_map = 0;
+
 	rc = gpmc_probe_dt(pdev);
 	if (rc < 0) {
 		clk_disable_unprepare(gpmc_l3_clk);
diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c
index 6a217c98db54..f82cf878d6af 100644
--- a/arch/arm/mach-omap2/mux.c
+++ b/arch/arm/mach-omap2/mux.c
@@ -211,8 +211,6 @@ static int __init _omap_mux_get_by_name(struct omap_mux_partition *partition,
 		return -EINVAL;
 	}
 
-	pr_err("%s: Could not find signal %s\n", __func__, muxname);
-
 	return -ENODEV;
 }
 
@@ -234,6 +232,8 @@ int __init omap_mux_get_by_name(const char *muxname,
 		return mux_mode;
 	}
 
+	pr_err("%s: Could not find signal %s\n", __func__, muxname);
+
 	return -ENODEV;
 }
 
@@ -739,8 +739,9 @@ static void __init omap_mux_dbg_create_entry(
 	list_for_each_entry(e, &partition->muxmodes, node) {
 		struct omap_mux *m = &e->mux;
 
-		(void)debugfs_create_file(m->muxnames[0], S_IWUSR, mux_dbg_dir,
-					  m, &omap_mux_dbg_signal_fops);
+		(void)debugfs_create_file(m->muxnames[0], S_IWUSR | S_IRUGO,
+					  mux_dbg_dir, m,
+					  &omap_mux_dbg_signal_fops);
 	}
 }
 
diff --git a/arch/arm/mach-omap2/omap-smp.c b/arch/arm/mach-omap2/omap-smp.c
index d9727218dd0a..e7a449758ab5 100644
--- a/arch/arm/mach-omap2/omap-smp.c
+++ b/arch/arm/mach-omap2/omap-smp.c
@@ -67,13 +67,6 @@ static void __cpuinit omap4_secondary_init(unsigned int cpu)
 							4, 0, 0, 0, 0, 0);
 
 	/*
-	 * If any interrupts are already enabled for the primary
-	 * core (e.g. timer irq), then they will not have been enabled
-	 * for us: do so
-	 */
-	gic_secondary_init(0);
-
-	/*
 	 * Synchronise with the boot thread.
 	 */
 	spin_lock(&boot_lock);
diff --git a/arch/arm/mach-prima2/platsmp.c b/arch/arm/mach-prima2/platsmp.c
index 4b788310f6a6..c7c92e78f0cf 100644
--- a/arch/arm/mach-prima2/platsmp.c
+++ b/arch/arm/mach-prima2/platsmp.c
@@ -11,7 +11,6 @@
 #include <linux/delay.h>
 #include <linux/of.h>
 #include <linux/of_address.h>
-#include <linux/irqchip/arm-gic.h>
 #include <asm/page.h>
 #include <asm/mach/map.h>
 #include <asm/smp_plat.h>
@@ -49,13 +48,6 @@ void __init sirfsoc_map_scu(void)
 static void __cpuinit sirfsoc_secondary_init(unsigned int cpu)
 {
 	/*
-	 * if any interrupts are already enabled for the primary
-	 * core (e.g. timer irq), then they will not have been enabled
-	 * for us: do so
-	 */
-	gic_secondary_init(0);
-
-	/*
 	 * let the primary processor know we're out of the
 	 * pen, then head off into the C entry point
 	 */
diff --git a/arch/arm/mach-pxa/raumfeld.c b/arch/arm/mach-pxa/raumfeld.c
index af41888acbd6..969b0ba7fa70 100644
--- a/arch/arm/mach-pxa/raumfeld.c
+++ b/arch/arm/mach-pxa/raumfeld.c
@@ -505,6 +505,7 @@ static struct w1_gpio_platform_data w1_gpio_platform_data = {
 	.pin			= GPIO_ONE_WIRE,
 	.is_open_drain		= 0,
 	.enable_external_pullup	= w1_enable_external_pullup,
+	.ext_pullup_enable_pin	= -EINVAL,
 };
 
 struct platform_device raumfeld_w1_gpio_device = {
diff --git a/arch/arm/mach-s3c24xx/irq.c b/arch/arm/mach-s3c24xx/irq.c
index c1b96f7cc587..05be3e2487ae 100644
--- a/arch/arm/mach-s3c24xx/irq.c
+++ b/arch/arm/mach-s3c24xx/irq.c
@@ -25,6 +25,7 @@
 #include <linux/ioport.h>
 #include <linux/device.h>
 #include <linux/irqdomain.h>
+#include <linux/irqchip/chained_irq.h>
 
 #include <asm/mach/irq.h>
 
diff --git a/arch/arm/mach-shmobile/smp-emev2.c b/arch/arm/mach-shmobile/smp-emev2.c
index 953eb1f9388d..384e27dd3601 100644
--- a/arch/arm/mach-shmobile/smp-emev2.c
+++ b/arch/arm/mach-shmobile/smp-emev2.c
@@ -23,7 +23,6 @@
 #include <linux/spinlock.h>
 #include <linux/io.h>
 #include <linux/delay.h>
-#include <linux/irqchip/arm-gic.h>
 #include <mach/common.h>
 #include <mach/emev2.h>
 #include <asm/smp_plat.h>
@@ -85,11 +84,6 @@ static int __maybe_unused emev2_cpu_kill(unsigned int cpu)
 }
 
 
-static void __cpuinit emev2_secondary_init(unsigned int cpu)
-{
-	gic_secondary_init(0);
-}
-
 static int __cpuinit emev2_boot_secondary(unsigned int cpu, struct task_struct *idle)
 {
 	cpu = cpu_logical_map(cpu);
@@ -124,7 +118,6 @@ static void __init emev2_smp_init_cpus(void)
 struct smp_operations emev2_smp_ops __initdata = {
 	.smp_init_cpus		= emev2_smp_init_cpus,
 	.smp_prepare_cpus	= emev2_smp_prepare_cpus,
-	.smp_secondary_init	= emev2_secondary_init,
 	.smp_boot_secondary	= emev2_boot_secondary,
 #ifdef CONFIG_HOTPLUG_CPU
 	.cpu_kill		= emev2_cpu_kill,
diff --git a/arch/arm/mach-shmobile/smp-r8a7779.c b/arch/arm/mach-shmobile/smp-r8a7779.c
index 3a4acf23edcf..994906560edd 100644
--- a/arch/arm/mach-shmobile/smp-r8a7779.c
+++ b/arch/arm/mach-shmobile/smp-r8a7779.c
@@ -23,7 +23,6 @@
 #include <linux/spinlock.h>
 #include <linux/io.h>
 #include <linux/delay.h>
-#include <linux/irqchip/arm-gic.h>
 #include <mach/common.h>
 #include <mach/r8a7779.h>
 #include <asm/smp_plat.h>
@@ -132,11 +131,6 @@ static int __maybe_unused r8a7779_cpu_kill(unsigned int cpu)
 }
 
 
-static void __cpuinit r8a7779_secondary_init(unsigned int cpu)
-{
-	gic_secondary_init(0);
-}
-
 static int __cpuinit r8a7779_boot_secondary(unsigned int cpu, struct task_struct *idle)
 {
 	struct r8a7779_pm_ch *ch = NULL;
@@ -186,7 +180,6 @@ static void __init r8a7779_smp_init_cpus(void)
 struct smp_operations r8a7779_smp_ops  __initdata = {
 	.smp_init_cpus		= r8a7779_smp_init_cpus,
 	.smp_prepare_cpus	= r8a7779_smp_prepare_cpus,
-	.smp_secondary_init	= r8a7779_secondary_init,
 	.smp_boot_secondary	= r8a7779_boot_secondary,
 #ifdef CONFIG_HOTPLUG_CPU
 	.cpu_kill		= r8a7779_cpu_kill,
diff --git a/arch/arm/mach-shmobile/smp-sh73a0.c b/arch/arm/mach-shmobile/smp-sh73a0.c
index acb46a94ccdf..d0f9aca22477 100644
--- a/arch/arm/mach-shmobile/smp-sh73a0.c
+++ b/arch/arm/mach-shmobile/smp-sh73a0.c
@@ -23,7 +23,6 @@
 #include <linux/spinlock.h>
 #include <linux/io.h>
 #include <linux/delay.h>
-#include <linux/irqchip/arm-gic.h>
 #include <mach/common.h>
 #include <asm/cacheflush.h>
 #include <asm/smp_plat.h>
@@ -59,11 +58,6 @@ static unsigned int __init sh73a0_get_core_count(void)
 	return scu_get_core_count(scu_base);
 }
 
-static void __cpuinit sh73a0_secondary_init(unsigned int cpu)
-{
-	gic_secondary_init(0);
-}
-
 static int __cpuinit sh73a0_boot_secondary(unsigned int cpu, struct task_struct *idle)
 {
 	cpu = cpu_logical_map(cpu);
@@ -138,7 +132,6 @@ static void sh73a0_cpu_die(unsigned int cpu)
 struct smp_operations sh73a0_smp_ops __initdata = {
 	.smp_init_cpus		= sh73a0_smp_init_cpus,
 	.smp_prepare_cpus	= sh73a0_smp_prepare_cpus,
-	.smp_secondary_init	= sh73a0_secondary_init,
 	.smp_boot_secondary	= sh73a0_boot_secondary,
 #ifdef CONFIG_HOTPLUG_CPU
 	.cpu_kill		= sh73a0_cpu_kill,
diff --git a/arch/arm/mach-socfpga/platsmp.c b/arch/arm/mach-socfpga/platsmp.c
index 84c60fa8daa0..ca14d1d5ac7f 100644
--- a/arch/arm/mach-socfpga/platsmp.c
+++ b/arch/arm/mach-socfpga/platsmp.c
@@ -22,7 +22,6 @@
 #include <linux/io.h>
 #include <linux/of.h>
 #include <linux/of_address.h>
-#include <linux/irqchip/arm-gic.h>
 
 #include <asm/cacheflush.h>
 #include <asm/smp_scu.h>
@@ -33,16 +32,6 @@
 extern void __iomem *sys_manager_base_addr;
 extern void __iomem *rst_manager_base_addr;
 
-static void __cpuinit socfpga_secondary_init(unsigned int cpu)
-{
-	/*
-	 * if any interrupts are already enabled for the primary
-	 * core (e.g. timer irq), then they will not have been enabled
-	 * for us: do so
-	 */
-	gic_secondary_init(0);
-}
-
 static int __cpuinit socfpga_boot_secondary(unsigned int cpu, struct task_struct *idle)
 {
 	int trampoline_size = &secondary_trampoline_end - &secondary_trampoline;
@@ -109,7 +98,6 @@ static void socfpga_cpu_die(unsigned int cpu)
 struct smp_operations socfpga_smp_ops __initdata = {
 	.smp_init_cpus		= socfpga_smp_init_cpus,
 	.smp_prepare_cpus	= socfpga_smp_prepare_cpus,
-	.smp_secondary_init	= socfpga_secondary_init,
 	.smp_boot_secondary	= socfpga_boot_secondary,
 #ifdef CONFIG_HOTPLUG_CPU
 	.cpu_die		= socfpga_cpu_die,
diff --git a/arch/arm/mach-spear13xx/platsmp.c b/arch/arm/mach-spear13xx/platsmp.c
index af4ade61cd95..551c69c9a228 100644
--- a/arch/arm/mach-spear13xx/platsmp.c
+++ b/arch/arm/mach-spear13xx/platsmp.c
@@ -15,7 +15,6 @@
 #include <linux/jiffies.h>
 #include <linux/io.h>
 #include <linux/smp.h>
-#include <linux/irqchip/arm-gic.h>
 #include <asm/cacheflush.h>
 #include <asm/smp_scu.h>
 #include <mach/spear.h>
@@ -28,13 +27,6 @@ static void __iomem *scu_base = IOMEM(VA_SCU_BASE);
 static void __cpuinit spear13xx_secondary_init(unsigned int cpu)
 {
 	/*
-	 * if any interrupts are already enabled for the primary
-	 * core (e.g. timer irq), then they will not have been enabled
-	 * for us: do so
-	 */
-	gic_secondary_init(0);
-
-	/*
 	 * let the primary processor know we're out of the
 	 * pen, then head off into the C entry point
 	 */
diff --git a/arch/arm/mach-spear3xx/spear3xx.c b/arch/arm/mach-spear3xx/spear3xx.c
index f9d754f90c59..d2b3937c4014 100644
--- a/arch/arm/mach-spear3xx/spear3xx.c
+++ b/arch/arm/mach-spear3xx/spear3xx.c
@@ -14,7 +14,7 @@
 #define pr_fmt(fmt) "SPEAr3xx: " fmt
 
 #include <linux/amba/pl022.h>
-#include <linux/amba/pl08x.h>
+#include <linux/amba/pl080.h>
 #include <linux/io.h>
 #include <plat/pl080.h>
 #include <mach/generic.h>
diff --git a/arch/arm/mach-tegra/platsmp.c b/arch/arm/mach-tegra/platsmp.c
index 2c6b3d55213b..9348d3c496a9 100644
--- a/arch/arm/mach-tegra/platsmp.c
+++ b/arch/arm/mach-tegra/platsmp.c
@@ -18,7 +18,6 @@
 #include <linux/jiffies.h>
 #include <linux/smp.h>
 #include <linux/io.h>
-#include <linux/irqchip/arm-gic.h>
 #include <linux/clk/tegra.h>
 
 #include <asm/cacheflush.h>
@@ -44,13 +43,6 @@ static cpumask_t tegra_cpu_init_mask;
 
 static void __cpuinit tegra_secondary_init(unsigned int cpu)
 {
-	/*
-	 * if any interrupts are already enabled for the primary
-	 * core (e.g. timer irq), then they will not have been enabled
-	 * for us: do so
-	 */
-	gic_secondary_init(0);
-
 	cpumask_set_cpu(cpu, &tegra_cpu_init_mask);
 }
 
diff --git a/arch/arm/mach-ux500/platsmp.c b/arch/arm/mach-ux500/platsmp.c
index 18f7af339dc9..152b1309b9af 100644
--- a/arch/arm/mach-ux500/platsmp.c
+++ b/arch/arm/mach-ux500/platsmp.c
@@ -16,7 +16,6 @@
 #include <linux/device.h>
 #include <linux/smp.h>
 #include <linux/io.h>
-#include <linux/irqchip/arm-gic.h>
 
 #include <asm/cacheflush.h>
 #include <asm/smp_plat.h>
@@ -58,13 +57,6 @@ static DEFINE_SPINLOCK(boot_lock);
 static void __cpuinit ux500_secondary_init(unsigned int cpu)
 {
 	/*
-	 * if any interrupts are already enabled for the primary
-	 * core (e.g. timer irq), then they will not have been enabled
-	 * for us: do so
-	 */
-	gic_secondary_init(0);
-
-	/*
 	 * let the primary processor know we're out of the
 	 * pen, then head off into the C entry point
 	 */
diff --git a/arch/arm/mach-virt/platsmp.c b/arch/arm/mach-virt/platsmp.c
index 8badaabe70a1..f4143f5bfa5b 100644
--- a/arch/arm/mach-virt/platsmp.c
+++ b/arch/arm/mach-virt/platsmp.c
@@ -21,8 +21,6 @@
 #include <linux/smp.h>
 #include <linux/of.h>
 
-#include <linux/irqchip/arm-gic.h>
-
 #include <asm/psci.h>
 #include <asm/smp_plat.h>
 
@@ -45,14 +43,8 @@ static int __cpuinit virt_boot_secondary(unsigned int cpu,
 	return -ENODEV;
 }
 
-static void __cpuinit virt_secondary_init(unsigned int cpu)
-{
-	gic_secondary_init(0);
-}
-
 struct smp_operations __initdata virt_smp_ops = {
 	.smp_init_cpus		= virt_smp_init_cpus,
 	.smp_prepare_cpus	= virt_smp_prepare_cpus,
-	.smp_secondary_init	= virt_secondary_init,
 	.smp_boot_secondary	= virt_boot_secondary,
 };
diff --git a/arch/arm/mm/dma-mapping.c b/arch/arm/mm/dma-mapping.c
index c7e3759f16d3..e9db6b4bf65a 100644
--- a/arch/arm/mm/dma-mapping.c
+++ b/arch/arm/mm/dma-mapping.c
@@ -342,6 +342,7 @@ static int __init atomic_pool_init(void)
 {
 	struct dma_pool *pool = &atomic_pool;
 	pgprot_t prot = pgprot_dmacoherent(pgprot_kernel);
+	gfp_t gfp = GFP_KERNEL | GFP_DMA;
 	unsigned long nr_pages = pool->size >> PAGE_SHIFT;
 	unsigned long *bitmap;
 	struct page *page;
@@ -361,8 +362,8 @@ static int __init atomic_pool_init(void)
 		ptr = __alloc_from_contiguous(NULL, pool->size, prot, &page,
 					      atomic_pool_init);
 	else
-		ptr = __alloc_remap_buffer(NULL, pool->size, GFP_KERNEL, prot,
-					   &page, atomic_pool_init);
+		ptr = __alloc_remap_buffer(NULL, pool->size, gfp, prot, &page,
+					   atomic_pool_init);
 	if (ptr) {
 		int i;
 
diff --git a/arch/arm/plat-orion/addr-map.c b/arch/arm/plat-orion/addr-map.c
index febe3862873c..807ac8e5cbc0 100644
--- a/arch/arm/plat-orion/addr-map.c
+++ b/arch/arm/plat-orion/addr-map.c
@@ -157,9 +157,12 @@ void __init orion_setup_cpu_mbus_target(const struct orion_addr_map_cfg *cfg,
 		u32 size = readl(ddr_window_cpu_base + DDR_SIZE_CS_OFF(i));
 
 		/*
-		 * Chip select enabled?
+		 * We only take care of entries for which the chip
+		 * select is enabled, and that don't have high base
+		 * address bits set (devices can only access the first
+		 * 32 bits of the memory).
 		 */
-		if (size & 1) {
+		if ((size & 1) && !(base & 0xF)) {
 			struct mbus_dram_window *w;
 
 			w = &orion_mbus_dram_info.cs[cs++];
diff --git a/arch/arm/plat-samsung/irq-vic-timer.c b/arch/arm/plat-samsung/irq-vic-timer.c
index f980cf3d2baa..5d205e74e495 100644
--- a/arch/arm/plat-samsung/irq-vic-timer.c
+++ b/arch/arm/plat-samsung/irq-vic-timer.c
@@ -16,6 +16,7 @@
 #include <linux/kernel.h>
 #include <linux/interrupt.h>
 #include <linux/irq.h>
+#include <linux/irqchip/chained_irq.h>
 #include <linux/io.h>
 
 #include <mach/map.h>
@@ -23,8 +24,6 @@
 #include <plat/irq-vic-timer.h>
 #include <plat/regs-timer.h>
 
-#include <asm/mach/irq.h>
-
 static void s3c_irq_demux_vic_timer(unsigned int irq, struct irq_desc *desc)
 {
 	struct irq_chip *chip = irq_get_chip(irq);
diff --git a/arch/arm/plat-samsung/s5p-irq-gpioint.c b/arch/arm/plat-samsung/s5p-irq-gpioint.c
index bae56131a50a..fafdb059043a 100644
--- a/arch/arm/plat-samsung/s5p-irq-gpioint.c
+++ b/arch/arm/plat-samsung/s5p-irq-gpioint.c
@@ -14,6 +14,7 @@
 #include <linux/kernel.h>
 #include <linux/interrupt.h>
 #include <linux/irq.h>
+#include <linux/irqchip/chained_irq.h>
 #include <linux/io.h>
 #include <linux/gpio.h>
 #include <linux/slab.h>
@@ -22,8 +23,6 @@
 #include <plat/gpio-core.h>
 #include <plat/gpio-cfg.h>
 
-#include <asm/mach/irq.h>
-
 #define GPIO_BASE(chip)		((void __iomem *)((unsigned long)((chip)->base) & 0xFFFFF000u))
 
 #define CON_OFFSET		0x700
diff --git a/arch/arm/plat-spear/Kconfig b/arch/arm/plat-spear/Kconfig
index 739d016eb273..8a08c31b5e20 100644
--- a/arch/arm/plat-spear/Kconfig
+++ b/arch/arm/plat-spear/Kconfig
@@ -10,7 +10,7 @@ choice
 
 config ARCH_SPEAR13XX
 	bool "ST SPEAr13xx with Device Tree"
-	select ARCH_HAVE_CPUFREQ
+	select ARCH_HAS_CPUFREQ
 	select ARM_GIC
 	select CPU_V7
 	select GPIO_SPEAR_SPICS
diff --git a/arch/arm/plat-versatile/platsmp.c b/arch/arm/plat-versatile/platsmp.c
index f2ac15561778..1e1b2d769748 100644
--- a/arch/arm/plat-versatile/platsmp.c
+++ b/arch/arm/plat-versatile/platsmp.c
@@ -14,7 +14,6 @@
 #include <linux/device.h>
 #include <linux/jiffies.h>
 #include <linux/smp.h>
-#include <linux/irqchip/arm-gic.h>
 
 #include <asm/cacheflush.h>
 #include <asm/smp_plat.h>
@@ -37,13 +36,6 @@ static DEFINE_SPINLOCK(boot_lock);
 void __cpuinit versatile_secondary_init(unsigned int cpu)
 {
 	/*
-	 * if any interrupts are already enabled for the primary
-	 * core (e.g. timer irq), then they will not have been enabled
-	 * for us: do so
-	 */
-	gic_secondary_init(0);
-
-	/*
 	 * let the primary processor know we're out of the
 	 * pen, then head off into the C entry point
 	 */