OMAP4: PRM: add module hard reset support

Most processor modules (e.g., DSP, IVA, IPU) on OMAPs can be reset
under the control of the PRM.  This patch adds an API for this purpose
for OMAP4 devices:

int omap4_prm_is_hardreset_asserted(void __iomem *rstctrl_reg, u8 shift);
int omap4_prm_assert_hardreset(void __iomem *rstctrl_reg, u8 shift);
int omap4_prm_deassert_hardreset(void __iomem *rstctrl_reg, u8 shift);

This API is intended to be used only by the hwmod code - a subsequent
patch will add that support to hwmod.

This patch is a collaboration between Benoît Cousson <b-cousson@ti.com>
and Paul Walmsley <paul@pwsan.com>.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>

3 files changed, 129 insertions, 2 deletions

diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index 88d3a1e920f5..c0da784e6b28 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -15,7 +15,7 @@ clock-common				= clock.o clock_common_data.o \
 
 obj-$(CONFIG_ARCH_OMAP2) += $(omap-2-3-common) $(prcm-common) $(hwmod-common)
 obj-$(CONFIG_ARCH_OMAP3) += $(omap-2-3-common) $(prcm-common) $(hwmod-common)
-obj-$(CONFIG_ARCH_OMAP4) += $(prcm-common) $(hwmod-common)
+obj-$(CONFIG_ARCH_OMAP4) += $(prcm-common) prm44xx.o $(hwmod-common)
 
 obj-$(CONFIG_OMAP_MCBSP) += mcbsp.o
 
diff --git a/arch/arm/mach-omap2/prm.h b/arch/arm/mach-omap2/prm.h
index 588873b9303a..bc7e6e6099d5 100644
--- a/arch/arm/mach-omap2/prm.h
+++ b/arch/arm/mach-omap2/prm.h
@@ -5,7 +5,7 @@
  * OMAP2/3 Power/Reset Management (PRM) register definitions
  *
  * Copyright (C) 2007-2009 Texas Instruments, Inc.
- * Copyright (C) 2009 Nokia Corporation
+ * Copyright (C) 2010 Nokia Corporation
  *
  * Written by Paul Walmsley
  *
@@ -246,6 +246,10 @@ static inline u32 prm_clear_mod_reg_bits(u32 bits, s16 module, s16 idx)
 	return prm_rmw_mod_reg_bits(bits, 0x0, module, idx);
 }
 
+int omap4_prm_is_hardreset_asserted(void __iomem *rstctrl_reg, u8 shift);
+int omap4_prm_assert_hardreset(void __iomem *rstctrl_reg, u8 shift);
+int omap4_prm_deassert_hardreset(void __iomem *rstctrl_reg, u8 shift);
+
 #endif
 
 /*
@@ -398,4 +402,11 @@ static inline u32 prm_clear_mod_reg_bits(u32 bits, s16 module, s16 idx)
 #define OMAP_POWERSTATE_MASK				(0x3 << 0)
 
 
+/*
+ * MAX_MODULE_HARDRESET_WAIT: Maximum microseconds to wait for an OMAP
+ * submodule to exit hardreset
+ */
+#define MAX_MODULE_HARDRESET_WAIT		10000
+
+
 #endif
diff --git a/arch/arm/mach-omap2/prm44xx.c b/arch/arm/mach-omap2/prm44xx.c
new file mode 100644
index 000000000000..a1ff918d9bed
--- /dev/null
+++ b/arch/arm/mach-omap2/prm44xx.c
@@ -0,0 +1,116 @@
+/*
+ * OMAP4 PRM module functions
+ *
+ * Copyright (C) 2010 Texas Instruments, Inc.
+ * Copyright (C) 2010 Nokia Corporation
+ * Benoît Cousson
+ * Paul Walmsley
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/err.h>
+
+#include <plat/common.h>
+#include <plat/cpu.h>
+#include <plat/prcm.h>
+
+#include "prm.h"
+#include "prm-regbits-44xx.h"
+
+/*
+ * Address offset (in bytes) between the reset control and the reset
+ * status registers: 4 bytes on OMAP4
+ */
+#define OMAP4_RST_CTRL_ST_OFFSET		4
+
+/**
+ * omap4_prm_is_hardreset_asserted - read the HW reset line state of
+ * submodules contained in the hwmod module
+ * @rstctrl_reg: RM_RSTCTRL register address for this module
+ * @shift: register bit shift corresponding to the reset line to check
+ *
+ * Returns 1 if the (sub)module hardreset line is currently asserted,
+ * 0 if the (sub)module hardreset line is not currently asserted, or
+ * -EINVAL upon parameter error.
+ */
+int omap4_prm_is_hardreset_asserted(void __iomem *rstctrl_reg, u8 shift)
+{
+	if (!cpu_is_omap44xx() || !rstctrl_reg)
+		return -EINVAL;
+
+	return omap4_prm_read_bits_shift(rstctrl_reg, (1 << shift));
+}
+
+/**
+ * omap4_prm_assert_hardreset - assert the HW reset line of a submodule
+ * @rstctrl_reg: RM_RSTCTRL register address for this module
+ * @shift: register bit shift corresponding to the reset line to assert
+ *
+ * Some IPs like dsp, ipu or iva contain processors that require an HW
+ * reset line to be asserted / deasserted in order to fully enable the
+ * IP.  These modules may have multiple hard-reset lines that reset
+ * different 'submodules' inside the IP block.  This function will
+ * place the submodule into reset.  Returns 0 upon success or -EINVAL
+ * upon an argument error.
+ */
+int omap4_prm_assert_hardreset(void __iomem *rstctrl_reg, u8 shift)
+{
+	u32 mask;
+
+	if (!cpu_is_omap44xx() || !rstctrl_reg)
+		return -EINVAL;
+
+	mask = 1 << shift;
+	omap4_prm_rmw_reg_bits(mask, mask, rstctrl_reg);
+
+	return 0;
+}
+
+/**
+ * omap4_prm_deassert_hardreset - deassert a submodule hardreset line and wait
+ * @rstctrl_reg: RM_RSTCTRL register address for this module
+ * @shift: register bit shift corresponding to the reset line to deassert
+ *
+ * Some IPs like dsp, ipu or iva contain processors that require an HW
+ * reset line to be asserted / deasserted in order to fully enable the
+ * IP.  These modules may have multiple hard-reset lines that reset
+ * different 'submodules' inside the IP block.  This function will
+ * take the submodule out of reset and wait until the PRCM indicates
+ * that the reset has completed before returning.  Returns 0 upon success or
+ * -EINVAL upon an argument error, -EEXIST if the submodule was already out
+ * of reset, or -EBUSY if the submodule did not exit reset promptly.
+ */
+int omap4_prm_deassert_hardreset(void __iomem *rstctrl_reg, u8 shift)
+{
+	u32 mask;
+	void __iomem *rstst_reg;
+	int c;
+
+	if (!cpu_is_omap44xx() || !rstctrl_reg)
+		return -EINVAL;
+
+	rstst_reg = rstctrl_reg + OMAP4_RST_CTRL_ST_OFFSET;
+
+	mask = 1 << shift;
+
+	/* Check the current status to avoid de-asserting the line twice */
+	if (omap4_prm_read_bits_shift(rstctrl_reg, mask) == 0)
+		return -EEXIST;
+
+	/* Clear the reset status by writing 1 to the status bit */
+	omap4_prm_rmw_reg_bits(0xffffffff, mask, rstst_reg);
+	/* de-assert the reset control line */
+	omap4_prm_rmw_reg_bits(mask, 0, rstctrl_reg);
+	/* wait the status to be set */
+	omap_test_timeout(omap4_prm_read_bits_shift(rstst_reg, mask),
+			  MAX_MODULE_HARDRESET_WAIT, c);
+
+	return (c == MAX_MODULE_HARDRESET_WAIT) ? -EBUSY : 0;
+}
+