USB: host: Remove ehci-octeon and ohci-octeon drivers

Remove special-purpose octeon drivers and instead use ehci-platform
and ohci-platform as suggested with
http://marc.info/?l=linux-mips&m=140139694721623&w=2

[andreas.herrmann:
    fixed compile error]

Cc: David Daney <david.daney@cavium.com>
Cc: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Andreas Herrmann <andreas.herrmann@caviumnetworks.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

7 files changed, 10 insertions, 597 deletions

diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index a3ca1375dd52..fafc628480e0 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -292,11 +292,15 @@ config USB_EHCI_HCD_PLATFORM
 	  If unsure, say N.
 
 config USB_OCTEON_EHCI
-	bool "Octeon on-chip EHCI support"
+	bool "Octeon on-chip EHCI support (DEPRECATED)"
 	depends on CAVIUM_OCTEON_SOC
 	default n
 	select USB_EHCI_BIG_ENDIAN_MMIO
+	select USB_EHCI_HCD_PLATFORM
 	help
+	  This option is deprecated now and the driver was removed, use
+	  USB_EHCI_HCD_PLATFORM instead.
+
 	  Enable support for the Octeon II SOC's on-chip EHCI
 	  controller.  It is needed for high-speed (480Mbit/sec)
 	  USB 2.0 device support.  All CN6XXX based chips with USB are
@@ -575,12 +579,16 @@ config USB_OHCI_HCD_PLATFORM
 	  If unsure, say N.
 
 config USB_OCTEON_OHCI
-	bool "Octeon on-chip OHCI support"
+	bool "Octeon on-chip OHCI support (DEPRECATED)"
 	depends on CAVIUM_OCTEON_SOC
 	default USB_OCTEON_EHCI
 	select USB_OHCI_BIG_ENDIAN_MMIO
 	select USB_OHCI_LITTLE_ENDIAN
+	select USB_OHCI_HCD_PLATFORM
 	help
+	  This option is deprecated now and the driver was removed, use
+	  USB_OHCI_HCD_PLATFORM instead.
+
 	  Enable support for the Octeon II SOC's on-chip OHCI
 	  controller.  It is needed for low-speed USB 1.0 device
 	  support.  All CN6XXX based chips with USB are supported.
@@ -754,12 +762,6 @@ config USB_IMX21_HCD
          To compile this driver as a module, choose M here: the
          module will be called "imx21-hcd".
 
-
-
-config USB_OCTEON2_COMMON
-	bool
-	default y if USB_OCTEON_EHCI || USB_OCTEON_OHCI
-
 config USB_HCD_BCMA
 	tristate "BCMA usb host driver"
 	depends on BCMA
diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index 348c24321562..d6216a493bab 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -73,7 +73,6 @@ obj-$(CONFIG_USB_ISP1760_HCD)	+= isp1760.o
 obj-$(CONFIG_USB_HWA_HCD)	+= hwa-hc.o
 obj-$(CONFIG_USB_IMX21_HCD)	+= imx21-hcd.o
 obj-$(CONFIG_USB_FSL_MPH_DR_OF)	+= fsl-mph-dr-of.o
-obj-$(CONFIG_USB_OCTEON2_COMMON) += octeon2-common.o
 obj-$(CONFIG_USB_HCD_BCMA)	+= bcma-hcd.o
 obj-$(CONFIG_USB_HCD_SSB)	+= ssb-hcd.o
 obj-$(CONFIG_USB_FUSBH200_HCD)	+= fusbh200-hcd.o
diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c
index df75b8e7d157..38bfeedae1d0 100644
--- a/drivers/usb/host/ehci-hcd.c
+++ b/drivers/usb/host/ehci-hcd.c
@@ -1275,11 +1275,6 @@ MODULE_LICENSE ("GPL");
 #define XILINX_OF_PLATFORM_DRIVER	ehci_hcd_xilinx_of_driver
 #endif
 
-#ifdef CONFIG_USB_OCTEON_EHCI
-#include "ehci-octeon.c"
-#define PLATFORM_DRIVER		ehci_octeon_driver
-#endif
-
 #ifdef CONFIG_TILE_USB
 #include "ehci-tilegx.c"
 #define	PLATFORM_DRIVER		ehci_hcd_tilegx_driver
diff --git a/drivers/usb/host/ehci-octeon.c b/drivers/usb/host/ehci-octeon.c
deleted file mode 100644
index 2d0c4bcba579..000000000000
--- a/drivers/usb/host/ehci-octeon.c
+++ /dev/null
@@ -1,182 +0,0 @@
-/*
- * EHCI HCD glue for Cavium Octeon II SOCs.
- *
- * Loosely based on ehci-au1xxx.c
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2010 Cavium Networks
- *
- */
-
-#include <linux/platform_device.h>
-
-#include <asm/octeon/octeon.h>
-#include <asm/octeon/cvmx-uctlx-defs.h>
-
-#define OCTEON_EHCI_HCD_NAME "octeon-ehci"
-
-/* Common clock init code.  */
-void octeon2_usb_clocks_start(void);
-void octeon2_usb_clocks_stop(void);
-
-static void ehci_octeon_start(void)
-{
-	union cvmx_uctlx_ehci_ctl ehci_ctl;
-
-	octeon2_usb_clocks_start();
-
-	ehci_ctl.u64 = cvmx_read_csr(CVMX_UCTLX_EHCI_CTL(0));
-	/* Use 64-bit addressing. */
-	ehci_ctl.s.ehci_64b_addr_en = 1;
-	ehci_ctl.s.l2c_addr_msb = 0;
-	ehci_ctl.s.l2c_buff_emod = 1; /* Byte swapped. */
-	ehci_ctl.s.l2c_desc_emod = 1; /* Byte swapped. */
-	cvmx_write_csr(CVMX_UCTLX_EHCI_CTL(0), ehci_ctl.u64);
-}
-
-static void ehci_octeon_stop(void)
-{
-	octeon2_usb_clocks_stop();
-}
-
-static const struct hc_driver ehci_octeon_hc_driver = {
-	.description		= hcd_name,
-	.product_desc		= "Octeon EHCI",
-	.hcd_priv_size		= sizeof(struct ehci_hcd),
-
-	/*
-	 * generic hardware linkage
-	 */
-	.irq			= ehci_irq,
-	.flags			= HCD_MEMORY | HCD_USB2 | HCD_BH,
-
-	/*
-	 * basic lifecycle operations
-	 */
-	.reset			= ehci_setup,
-	.start			= ehci_run,
-	.stop			= ehci_stop,
-	.shutdown		= ehci_shutdown,
-
-	/*
-	 * managing i/o requests and associated device resources
-	 */
-	.urb_enqueue		= ehci_urb_enqueue,
-	.urb_dequeue		= ehci_urb_dequeue,
-	.endpoint_disable	= ehci_endpoint_disable,
-	.endpoint_reset		= ehci_endpoint_reset,
-
-	/*
-	 * scheduling support
-	 */
-	.get_frame_number	= ehci_get_frame,
-
-	/*
-	 * root hub support
-	 */
-	.hub_status_data	= ehci_hub_status_data,
-	.hub_control		= ehci_hub_control,
-	.bus_suspend		= ehci_bus_suspend,
-	.bus_resume		= ehci_bus_resume,
-	.relinquish_port	= ehci_relinquish_port,
-	.port_handed_over	= ehci_port_handed_over,
-
-	.clear_tt_buffer_complete	= ehci_clear_tt_buffer_complete,
-};
-
-static u64 ehci_octeon_dma_mask = DMA_BIT_MASK(64);
-
-static int ehci_octeon_drv_probe(struct platform_device *pdev)
-{
-	struct usb_hcd *hcd;
-	struct ehci_hcd *ehci;
-	struct resource *res_mem;
-	int irq;
-	int ret;
-
-	if (usb_disabled())
-		return -ENODEV;
-
-	irq = platform_get_irq(pdev, 0);
-	if (irq < 0) {
-		dev_err(&pdev->dev, "No irq assigned\n");
-		return -ENODEV;
-	}
-
-	/*
-	 * We can DMA from anywhere. But the descriptors must be in
-	 * the lower 4GB.
-	 */
-	pdev->dev.dma_mask = &ehci_octeon_dma_mask;
-	ret = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32));
-	if (ret)
-		return ret;
-
-	hcd = usb_create_hcd(&ehci_octeon_hc_driver, &pdev->dev, "octeon");
-	if (!hcd)
-		return -ENOMEM;
-
-	res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	hcd->regs = devm_ioremap_resource(&pdev->dev, res_mem);
-	if (IS_ERR(hcd->regs)) {
-		ret = PTR_ERR(hcd->regs);
-		goto err1;
-	}
-	hcd->rsrc_start = res_mem->start;
-	hcd->rsrc_len = resource_size(res_mem);
-
-	ehci_octeon_start();
-
-	ehci = hcd_to_ehci(hcd);
-
-	/* Octeon EHCI matches CPU endianness. */
-#ifdef __BIG_ENDIAN
-	ehci->big_endian_mmio = 1;
-#endif
-
-	ehci->caps = hcd->regs;
-
-	ret = usb_add_hcd(hcd, irq, IRQF_SHARED);
-	if (ret) {
-		dev_dbg(&pdev->dev, "failed to add hcd with err %d\n", ret);
-		goto err2;
-	}
-	device_wakeup_enable(hcd->self.controller);
-
-	platform_set_drvdata(pdev, hcd);
-
-	return 0;
-err2:
-	ehci_octeon_stop();
-
-err1:
-	usb_put_hcd(hcd);
-	return ret;
-}
-
-static int ehci_octeon_drv_remove(struct platform_device *pdev)
-{
-	struct usb_hcd *hcd = platform_get_drvdata(pdev);
-
-	usb_remove_hcd(hcd);
-
-	ehci_octeon_stop();
-	usb_put_hcd(hcd);
-
-	return 0;
-}
-
-static struct platform_driver ehci_octeon_driver = {
-	.probe		= ehci_octeon_drv_probe,
-	.remove		= ehci_octeon_drv_remove,
-	.shutdown	= usb_hcd_platform_shutdown,
-	.driver = {
-		.name	= OCTEON_EHCI_HCD_NAME,
-		.owner	= THIS_MODULE,
-	}
-};
-
-MODULE_ALIAS("platform:" OCTEON_EHCI_HCD_NAME);
diff --git a/drivers/usb/host/octeon2-common.c b/drivers/usb/host/octeon2-common.c
deleted file mode 100644
index d9df423f3d12..000000000000
--- a/drivers/usb/host/octeon2-common.c
+++ /dev/null
@@ -1,200 +0,0 @@
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2010, 2011 Cavium Networks
- */
-
-#include <linux/module.h>
-#include <linux/mutex.h>
-#include <linux/delay.h>
-
-#include <asm/octeon/octeon.h>
-#include <asm/octeon/cvmx-uctlx-defs.h>
-
-static DEFINE_MUTEX(octeon2_usb_clocks_mutex);
-
-static int octeon2_usb_clock_start_cnt;
-
-void octeon2_usb_clocks_start(void)
-{
-	u64 div;
-	union cvmx_uctlx_if_ena if_ena;
-	union cvmx_uctlx_clk_rst_ctl clk_rst_ctl;
-	union cvmx_uctlx_uphy_ctl_status uphy_ctl_status;
-	union cvmx_uctlx_uphy_portx_ctl_status port_ctl_status;
-	int i;
-	unsigned long io_clk_64_to_ns;
-
-
-	mutex_lock(&octeon2_usb_clocks_mutex);
-
-	octeon2_usb_clock_start_cnt++;
-	if (octeon2_usb_clock_start_cnt != 1)
-		goto exit;
-
-	io_clk_64_to_ns = 64000000000ull / octeon_get_io_clock_rate();
-
-	/*
-	 * Step 1: Wait for voltages stable.  That surely happened
-	 * before starting the kernel.
-	 *
-	 * Step 2: Enable  SCLK of UCTL by writing UCTL0_IF_ENA[EN] = 1
-	 */
-	if_ena.u64 = 0;
-	if_ena.s.en = 1;
-	cvmx_write_csr(CVMX_UCTLX_IF_ENA(0), if_ena.u64);
-
-	/* Step 3: Configure the reference clock, PHY, and HCLK */
-	clk_rst_ctl.u64 = cvmx_read_csr(CVMX_UCTLX_CLK_RST_CTL(0));
-
-	/*
-	 * If the UCTL looks like it has already been started, skip
-	 * the initialization, otherwise bus errors are obtained.
-	 */
-	if (clk_rst_ctl.s.hrst)
-		goto end_clock;
-	/* 3a */
-	clk_rst_ctl.s.p_por = 1;
-	clk_rst_ctl.s.hrst = 0;
-	clk_rst_ctl.s.p_prst = 0;
-	clk_rst_ctl.s.h_clkdiv_rst = 0;
-	clk_rst_ctl.s.o_clkdiv_rst = 0;
-	clk_rst_ctl.s.h_clkdiv_en = 0;
-	clk_rst_ctl.s.o_clkdiv_en = 0;
-	cvmx_write_csr(CVMX_UCTLX_CLK_RST_CTL(0), clk_rst_ctl.u64);
-
-	/* 3b */
-	/* 12MHz crystal. */
-	clk_rst_ctl.s.p_refclk_sel = 0;
-	clk_rst_ctl.s.p_refclk_div = 0;
-	cvmx_write_csr(CVMX_UCTLX_CLK_RST_CTL(0), clk_rst_ctl.u64);
-
-	/* 3c */
-	div = octeon_get_io_clock_rate() / 130000000ull;
-
-	switch (div) {
-	case 0:
-		div = 1;
-		break;
-	case 1:
-	case 2:
-	case 3:
-	case 4:
-		break;
-	case 5:
-		div = 4;
-		break;
-	case 6:
-	case 7:
-		div = 6;
-		break;
-	case 8:
-	case 9:
-	case 10:
-	case 11:
-		div = 8;
-		break;
-	default:
-		div = 12;
-		break;
-	}
-	clk_rst_ctl.s.h_div = div;
-	cvmx_write_csr(CVMX_UCTLX_CLK_RST_CTL(0), clk_rst_ctl.u64);
-	/* Read it back, */
-	clk_rst_ctl.u64 = cvmx_read_csr(CVMX_UCTLX_CLK_RST_CTL(0));
-	clk_rst_ctl.s.h_clkdiv_en = 1;
-	cvmx_write_csr(CVMX_UCTLX_CLK_RST_CTL(0), clk_rst_ctl.u64);
-	/* 3d */
-	clk_rst_ctl.s.h_clkdiv_rst = 1;
-	cvmx_write_csr(CVMX_UCTLX_CLK_RST_CTL(0), clk_rst_ctl.u64);
-
-	/* 3e: delay 64 io clocks */
-	ndelay(io_clk_64_to_ns);
-
-	/*
-	 * Step 4: Program the power-on reset field in the UCTL
-	 * clock-reset-control register.
-	 */
-	clk_rst_ctl.s.p_por = 0;
-	cvmx_write_csr(CVMX_UCTLX_CLK_RST_CTL(0), clk_rst_ctl.u64);
-
-	/* Step 5:    Wait 1 ms for the PHY clock to start. */
-	mdelay(1);
-
-	/*
-	 * Step 6: Program the reset input from automatic test
-	 * equipment field in the UPHY CSR
-	 */
-	uphy_ctl_status.u64 = cvmx_read_csr(CVMX_UCTLX_UPHY_CTL_STATUS(0));
-	uphy_ctl_status.s.ate_reset = 1;
-	cvmx_write_csr(CVMX_UCTLX_UPHY_CTL_STATUS(0), uphy_ctl_status.u64);
-
-	/* Step 7: Wait for at least 10ns. */
-	ndelay(10);
-
-	/* Step 8: Clear the ATE_RESET field in the UPHY CSR. */
-	uphy_ctl_status.s.ate_reset = 0;
-	cvmx_write_csr(CVMX_UCTLX_UPHY_CTL_STATUS(0), uphy_ctl_status.u64);
-
-	/*
-	 * Step 9: Wait for at least 20ns for UPHY to output PHY clock
-	 * signals and OHCI_CLK48
-	 */
-	ndelay(20);
-
-	/* Step 10: Configure the OHCI_CLK48 and OHCI_CLK12 clocks. */
-	/* 10a */
-	clk_rst_ctl.s.o_clkdiv_rst = 1;
-	cvmx_write_csr(CVMX_UCTLX_CLK_RST_CTL(0), clk_rst_ctl.u64);
-
-	/* 10b */
-	clk_rst_ctl.s.o_clkdiv_en = 1;
-	cvmx_write_csr(CVMX_UCTLX_CLK_RST_CTL(0), clk_rst_ctl.u64);
-
-	/* 10c */
-	ndelay(io_clk_64_to_ns);
-
-	/*
-	 * Step 11: Program the PHY reset field:
-	 * UCTL0_CLK_RST_CTL[P_PRST] = 1
-	 */
-	clk_rst_ctl.s.p_prst = 1;
-	cvmx_write_csr(CVMX_UCTLX_CLK_RST_CTL(0), clk_rst_ctl.u64);
-
-	/* Step 12: Wait 1 uS. */
-	udelay(1);
-
-	/* Step 13: Program the HRESET_N field: UCTL0_CLK_RST_CTL[HRST] = 1 */
-	clk_rst_ctl.s.hrst = 1;
-	cvmx_write_csr(CVMX_UCTLX_CLK_RST_CTL(0), clk_rst_ctl.u64);
-
-end_clock:
-	/* Now we can set some other registers.  */
-
-	for (i = 0; i <= 1; i++) {
-		port_ctl_status.u64 =
-			cvmx_read_csr(CVMX_UCTLX_UPHY_PORTX_CTL_STATUS(i, 0));
-		/* Set txvreftune to 15 to obtain compliant 'eye' diagram. */
-		port_ctl_status.s.txvreftune = 15;
-		port_ctl_status.s.txrisetune = 1;
-		port_ctl_status.s.txpreemphasistune = 1;
-		cvmx_write_csr(CVMX_UCTLX_UPHY_PORTX_CTL_STATUS(i, 0),
-			       port_ctl_status.u64);
-	}
-
-	/* Set uSOF cycle period to 60,000 bits. */
-	cvmx_write_csr(CVMX_UCTLX_EHCI_FLA(0), 0x20ull);
-exit:
-	mutex_unlock(&octeon2_usb_clocks_mutex);
-}
-EXPORT_SYMBOL(octeon2_usb_clocks_start);
-
-void octeon2_usb_clocks_stop(void)
-{
-	mutex_lock(&octeon2_usb_clocks_mutex);
-	octeon2_usb_clock_start_cnt--;
-	mutex_unlock(&octeon2_usb_clocks_mutex);
-}
-EXPORT_SYMBOL(octeon2_usb_clocks_stop);
diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c
index d664edabf14e..1dab9dfbca6a 100644
--- a/drivers/usb/host/ohci-hcd.c
+++ b/drivers/usb/host/ohci-hcd.c
@@ -1249,11 +1249,6 @@ MODULE_LICENSE ("GPL");
 #define PLATFORM_DRIVER	ohci_hcd_jz4740_driver
 #endif
 
-#ifdef CONFIG_USB_OCTEON_OHCI
-#include "ohci-octeon.c"
-#define PLATFORM_DRIVER		ohci_octeon_driver
-#endif
-
 #ifdef CONFIG_TILE_USB
 #include "ohci-tilegx.c"
 #define PLATFORM_DRIVER		ohci_hcd_tilegx_driver
diff --git a/drivers/usb/host/ohci-octeon.c b/drivers/usb/host/ohci-octeon.c
deleted file mode 100644
index 20d861b6192f..000000000000
--- a/drivers/usb/host/ohci-octeon.c
+++ /dev/null
@@ -1,196 +0,0 @@
-/*
- * EHCI HCD glue for Cavium Octeon II SOCs.
- *
- * Loosely based on ehci-au1xxx.c
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2010 Cavium Networks
- *
- */
-
-#include <linux/platform_device.h>
-
-#include <asm/octeon/octeon.h>
-#include <asm/octeon/cvmx-uctlx-defs.h>
-
-#define OCTEON_OHCI_HCD_NAME "octeon-ohci"
-
-/* Common clock init code.  */
-void octeon2_usb_clocks_start(void);
-void octeon2_usb_clocks_stop(void);
-
-static void ohci_octeon_hw_start(void)
-{
-	union cvmx_uctlx_ohci_ctl ohci_ctl;
-
-	octeon2_usb_clocks_start();
-
-	ohci_ctl.u64 = cvmx_read_csr(CVMX_UCTLX_OHCI_CTL(0));
-	ohci_ctl.s.l2c_addr_msb = 0;
-	ohci_ctl.s.l2c_buff_emod = 1; /* Byte swapped. */
-	ohci_ctl.s.l2c_desc_emod = 1; /* Byte swapped. */
-	cvmx_write_csr(CVMX_UCTLX_OHCI_CTL(0), ohci_ctl.u64);
-
-}
-
-static void ohci_octeon_hw_stop(void)
-{
-	/* Undo ohci_octeon_start() */
-	octeon2_usb_clocks_stop();
-}
-
-static int ohci_octeon_start(struct usb_hcd *hcd)
-{
-	struct ohci_hcd	*ohci = hcd_to_ohci(hcd);
-	int ret;
-
-	ret = ohci_init(ohci);
-
-	if (ret < 0)
-		return ret;
-
-	ret = ohci_run(ohci);
-
-	if (ret < 0) {
-		ohci_err(ohci, "can't start %s", hcd->self.bus_name);
-		ohci_stop(hcd);
-		return ret;
-	}
-
-	return 0;
-}
-
-static const struct hc_driver ohci_octeon_hc_driver = {
-	.description		= hcd_name,
-	.product_desc		= "Octeon OHCI",
-	.hcd_priv_size		= sizeof(struct ohci_hcd),
-
-	/*
-	 * generic hardware linkage
-	 */
-	.irq =			ohci_irq,
-	.flags =		HCD_USB11 | HCD_MEMORY,
-
-	/*
-	 * basic lifecycle operations
-	 */
-	.start =		ohci_octeon_start,
-	.stop =			ohci_stop,
-	.shutdown =		ohci_shutdown,
-
-	/*
-	 * managing i/o requests and associated device resources
-	 */
-	.urb_enqueue =		ohci_urb_enqueue,
-	.urb_dequeue =		ohci_urb_dequeue,
-	.endpoint_disable =	ohci_endpoint_disable,
-
-	/*
-	 * scheduling support
-	 */
-	.get_frame_number =	ohci_get_frame,
-
-	/*
-	 * root hub support
-	 */
-	.hub_status_data =	ohci_hub_status_data,
-	.hub_control =		ohci_hub_control,
-
-	.start_port_reset =	ohci_start_port_reset,
-};
-
-static int ohci_octeon_drv_probe(struct platform_device *pdev)
-{
-	struct usb_hcd *hcd;
-	struct ohci_hcd *ohci;
-	void *reg_base;
-	struct resource *res_mem;
-	int irq;
-	int ret;
-
-	if (usb_disabled())
-		return -ENODEV;
-
-	irq = platform_get_irq(pdev, 0);
-	if (irq < 0) {
-		dev_err(&pdev->dev, "No irq assigned\n");
-		return -ENODEV;
-	}
-
-	/* Ohci is a 32-bit device. */
-	ret = dma_coerce_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
-	if (ret)
-		return ret;
-
-	hcd = usb_create_hcd(&ohci_octeon_hc_driver, &pdev->dev, "octeon");
-	if (!hcd)
-		return -ENOMEM;
-
-	res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	reg_base = devm_ioremap_resource(&pdev->dev, res_mem);
-	if (IS_ERR(reg_base)) {
-		ret = PTR_ERR(reg_base);
-		goto err1;
-	}
-	hcd->rsrc_start = res_mem->start;
-	hcd->rsrc_len = resource_size(res_mem);
-
-	ohci_octeon_hw_start();
-
-	hcd->regs = reg_base;
-
-	ohci = hcd_to_ohci(hcd);
-
-	/* Octeon OHCI matches CPU endianness. */
-#ifdef __BIG_ENDIAN
-	ohci->flags |= OHCI_QUIRK_BE_MMIO;
-#endif
-
-	ohci_hcd_init(ohci);
-
-	ret = usb_add_hcd(hcd, irq, IRQF_SHARED);
-	if (ret) {
-		dev_dbg(&pdev->dev, "failed to add hcd with err %d\n", ret);
-		goto err2;
-	}
-
-	device_wakeup_enable(hcd->self.controller);
-
-	platform_set_drvdata(pdev, hcd);
-
-	return 0;
-
-err2:
-	ohci_octeon_hw_stop();
-
-err1:
-	usb_put_hcd(hcd);
-	return ret;
-}
-
-static int ohci_octeon_drv_remove(struct platform_device *pdev)
-{
-	struct usb_hcd *hcd = platform_get_drvdata(pdev);
-
-	usb_remove_hcd(hcd);
-
-	ohci_octeon_hw_stop();
-	usb_put_hcd(hcd);
-
-	return 0;
-}
-
-static struct platform_driver ohci_octeon_driver = {
-	.probe		= ohci_octeon_drv_probe,
-	.remove		= ohci_octeon_drv_remove,
-	.shutdown	= usb_hcd_platform_shutdown,
-	.driver = {
-		.name	= OCTEON_OHCI_HCD_NAME,
-		.owner	= THIS_MODULE,
-	}
-};
-
-MODULE_ALIAS("platform:" OCTEON_OHCI_HCD_NAME);