Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC late updates from Olof Johansson:
 "This is a branch with a few merge requests that either came in late,
  or took a while longer for us to review and merge than usual and thus
  cut it a bit close to the merge window. We stage them in a separate
  branch and if things look good, we still send them up -- and that's
  the case here.

  This is mostly DT additions for Renesas platforms, adding IP block
  descriptions for existing and new SoCs.

  There are also some driver updates for Qualcomm platforms for SMEM/QMI
  and GENI, which is their generalized serial protocol interface"

* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (186 commits)
  soc: qcom: smem: introduce qcom_smem_virt_to_phys()
  soc: qcom: qmi: fix a buffer sizing bug
  MAINTAINERS: Update pattern for qcom_scm
  soc: Unconditionally include qcom Makefile
  soc: qcom: smem: check sooner in qcom_smem_set_global_partition()
  soc: qcom: smem: fix qcom_smem_set_global_partition()
  soc: qcom: smem: fix off-by-one error in qcom_smem_alloc_private()
  soc: qcom: smem: byte swap values properly
  soc: qcom: smem: return proper type for cached entry functions
  soc: qcom: smem: fix first cache entry calculation
  soc: qcom: cmd-db: Make endian-agnostic
  drivers: qcom: add command DB driver
  arm64: dts: renesas: salvator-common: Add ADV7482 support
  ARM: dts: r8a7740: Add CEU1
  ARM: dts: r8a7740: Add CEU0
  arm64: dts: renesas: salvator-common: enable VIN
  arm64: dts: renesas: r8a77970: add VIN and CSI-2 nodes
  arm64: dts: renesas: r8a77965: add VIN and CSI-2 nodes
  arm64: dts: renesas: r8a7796: add VIN and CSI-2 nodes
  arm64: dts: renesas: r8a7795-es1: add CSI-2 node
  ...

2 files changed, 427 insertions, 0 deletions

diff --git a/include/linux/qcom-geni-se.h b/include/linux/qcom-geni-se.h
new file mode 100644
index 000000000000..5d6144977828
--- /dev/null
+++ b/include/linux/qcom-geni-se.h
@@ -0,0 +1,425 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * Copyright (c) 2017-2018, The Linux Foundation. All rights reserved.
+ */
+
+#ifndef _LINUX_QCOM_GENI_SE
+#define _LINUX_QCOM_GENI_SE
+
+/* Transfer mode supported by GENI Serial Engines */
+enum geni_se_xfer_mode {
+	GENI_SE_INVALID,
+	GENI_SE_FIFO,
+	GENI_SE_DMA,
+};
+
+/* Protocols supported by GENI Serial Engines */
+enum geni_se_protocol_type {
+	GENI_SE_NONE,
+	GENI_SE_SPI,
+	GENI_SE_UART,
+	GENI_SE_I2C,
+	GENI_SE_I3C,
+};
+
+struct geni_wrapper;
+struct clk;
+
+/**
+ * struct geni_se - GENI Serial Engine
+ * @base:		Base Address of the Serial Engine's register block
+ * @dev:		Pointer to the Serial Engine device
+ * @wrapper:		Pointer to the parent QUP Wrapper core
+ * @clk:		Handle to the core serial engine clock
+ * @num_clk_levels:	Number of valid clock levels in clk_perf_tbl
+ * @clk_perf_tbl:	Table of clock frequency input to serial engine clock
+ */
+struct geni_se {
+	void __iomem *base;
+	struct device *dev;
+	struct geni_wrapper *wrapper;
+	struct clk *clk;
+	unsigned int num_clk_levels;
+	unsigned long *clk_perf_tbl;
+};
+
+/* Common SE registers */
+#define GENI_FORCE_DEFAULT_REG		0x20
+#define SE_GENI_STATUS			0x40
+#define GENI_SER_M_CLK_CFG		0x48
+#define GENI_SER_S_CLK_CFG		0x4c
+#define GENI_FW_REVISION_RO		0x68
+#define SE_GENI_CLK_SEL			0x7c
+#define SE_GENI_DMA_MODE_EN		0x258
+#define SE_GENI_M_CMD0			0x600
+#define SE_GENI_M_CMD_CTRL_REG		0x604
+#define SE_GENI_M_IRQ_STATUS		0x610
+#define SE_GENI_M_IRQ_EN		0x614
+#define SE_GENI_M_IRQ_CLEAR		0x618
+#define SE_GENI_S_CMD0			0x630
+#define SE_GENI_S_CMD_CTRL_REG		0x634
+#define SE_GENI_S_IRQ_STATUS		0x640
+#define SE_GENI_S_IRQ_EN		0x644
+#define SE_GENI_S_IRQ_CLEAR		0x648
+#define SE_GENI_TX_FIFOn		0x700
+#define SE_GENI_RX_FIFOn		0x780
+#define SE_GENI_TX_FIFO_STATUS		0x800
+#define SE_GENI_RX_FIFO_STATUS		0x804
+#define SE_GENI_TX_WATERMARK_REG	0x80c
+#define SE_GENI_RX_WATERMARK_REG	0x810
+#define SE_GENI_RX_RFR_WATERMARK_REG	0x814
+#define SE_GENI_IOS			0x908
+#define SE_DMA_TX_IRQ_STAT		0xc40
+#define SE_DMA_TX_IRQ_CLR		0xc44
+#define SE_DMA_TX_FSM_RST		0xc58
+#define SE_DMA_RX_IRQ_STAT		0xd40
+#define SE_DMA_RX_IRQ_CLR		0xd44
+#define SE_DMA_RX_FSM_RST		0xd58
+#define SE_HW_PARAM_0			0xe24
+#define SE_HW_PARAM_1			0xe28
+
+/* GENI_FORCE_DEFAULT_REG fields */
+#define FORCE_DEFAULT	BIT(0)
+
+/* GENI_STATUS fields */
+#define M_GENI_CMD_ACTIVE		BIT(0)
+#define S_GENI_CMD_ACTIVE		BIT(12)
+
+/* GENI_SER_M_CLK_CFG/GENI_SER_S_CLK_CFG */
+#define SER_CLK_EN			BIT(0)
+#define CLK_DIV_MSK			GENMASK(15, 4)
+#define CLK_DIV_SHFT			4
+
+/* GENI_FW_REVISION_RO fields */
+#define FW_REV_PROTOCOL_MSK		GENMASK(15, 8)
+#define FW_REV_PROTOCOL_SHFT		8
+
+/* GENI_CLK_SEL fields */
+#define CLK_SEL_MSK			GENMASK(2, 0)
+
+/* SE_GENI_DMA_MODE_EN */
+#define GENI_DMA_MODE_EN		BIT(0)
+
+/* GENI_M_CMD0 fields */
+#define M_OPCODE_MSK			GENMASK(31, 27)
+#define M_OPCODE_SHFT			27
+#define M_PARAMS_MSK			GENMASK(26, 0)
+
+/* GENI_M_CMD_CTRL_REG */
+#define M_GENI_CMD_CANCEL		BIT(2)
+#define M_GENI_CMD_ABORT		BIT(1)
+#define M_GENI_DISABLE			BIT(0)
+
+/* GENI_S_CMD0 fields */
+#define S_OPCODE_MSK			GENMASK(31, 27)
+#define S_OPCODE_SHFT			27
+#define S_PARAMS_MSK			GENMASK(26, 0)
+
+/* GENI_S_CMD_CTRL_REG */
+#define S_GENI_CMD_CANCEL		BIT(2)
+#define S_GENI_CMD_ABORT		BIT(1)
+#define S_GENI_DISABLE			BIT(0)
+
+/* GENI_M_IRQ_EN fields */
+#define M_CMD_DONE_EN			BIT(0)
+#define M_CMD_OVERRUN_EN		BIT(1)
+#define M_ILLEGAL_CMD_EN		BIT(2)
+#define M_CMD_FAILURE_EN		BIT(3)
+#define M_CMD_CANCEL_EN			BIT(4)
+#define M_CMD_ABORT_EN			BIT(5)
+#define M_TIMESTAMP_EN			BIT(6)
+#define M_RX_IRQ_EN			BIT(7)
+#define M_GP_SYNC_IRQ_0_EN		BIT(8)
+#define M_GP_IRQ_0_EN			BIT(9)
+#define M_GP_IRQ_1_EN			BIT(10)
+#define M_GP_IRQ_2_EN			BIT(11)
+#define M_GP_IRQ_3_EN			BIT(12)
+#define M_GP_IRQ_4_EN			BIT(13)
+#define M_GP_IRQ_5_EN			BIT(14)
+#define M_IO_DATA_DEASSERT_EN		BIT(22)
+#define M_IO_DATA_ASSERT_EN		BIT(23)
+#define M_RX_FIFO_RD_ERR_EN		BIT(24)
+#define M_RX_FIFO_WR_ERR_EN		BIT(25)
+#define M_RX_FIFO_WATERMARK_EN		BIT(26)
+#define M_RX_FIFO_LAST_EN		BIT(27)
+#define M_TX_FIFO_RD_ERR_EN		BIT(28)
+#define M_TX_FIFO_WR_ERR_EN		BIT(29)
+#define M_TX_FIFO_WATERMARK_EN		BIT(30)
+#define M_SEC_IRQ_EN			BIT(31)
+#define M_COMMON_GENI_M_IRQ_EN	(GENMASK(6, 1) | \
+				M_IO_DATA_DEASSERT_EN | \
+				M_IO_DATA_ASSERT_EN | M_RX_FIFO_RD_ERR_EN | \
+				M_RX_FIFO_WR_ERR_EN | M_TX_FIFO_RD_ERR_EN | \
+				M_TX_FIFO_WR_ERR_EN)
+
+/* GENI_S_IRQ_EN fields */
+#define S_CMD_DONE_EN			BIT(0)
+#define S_CMD_OVERRUN_EN		BIT(1)
+#define S_ILLEGAL_CMD_EN		BIT(2)
+#define S_CMD_FAILURE_EN		BIT(3)
+#define S_CMD_CANCEL_EN			BIT(4)
+#define S_CMD_ABORT_EN			BIT(5)
+#define S_GP_SYNC_IRQ_0_EN		BIT(8)
+#define S_GP_IRQ_0_EN			BIT(9)
+#define S_GP_IRQ_1_EN			BIT(10)
+#define S_GP_IRQ_2_EN			BIT(11)
+#define S_GP_IRQ_3_EN			BIT(12)
+#define S_GP_IRQ_4_EN			BIT(13)
+#define S_GP_IRQ_5_EN			BIT(14)
+#define S_IO_DATA_DEASSERT_EN		BIT(22)
+#define S_IO_DATA_ASSERT_EN		BIT(23)
+#define S_RX_FIFO_RD_ERR_EN		BIT(24)
+#define S_RX_FIFO_WR_ERR_EN		BIT(25)
+#define S_RX_FIFO_WATERMARK_EN		BIT(26)
+#define S_RX_FIFO_LAST_EN		BIT(27)
+#define S_COMMON_GENI_S_IRQ_EN	(GENMASK(5, 1) | GENMASK(13, 9) | \
+				 S_RX_FIFO_RD_ERR_EN | S_RX_FIFO_WR_ERR_EN)
+
+/*  GENI_/TX/RX/RX_RFR/_WATERMARK_REG fields */
+#define WATERMARK_MSK			GENMASK(5, 0)
+
+/* GENI_TX_FIFO_STATUS fields */
+#define TX_FIFO_WC			GENMASK(27, 0)
+
+/*  GENI_RX_FIFO_STATUS fields */
+#define RX_LAST				BIT(31)
+#define RX_LAST_BYTE_VALID_MSK		GENMASK(30, 28)
+#define RX_LAST_BYTE_VALID_SHFT		28
+#define RX_FIFO_WC_MSK			GENMASK(24, 0)
+
+/* SE_GENI_IOS fields */
+#define IO2_DATA_IN			BIT(1)
+#define RX_DATA_IN			BIT(0)
+
+/* SE_DMA_TX_IRQ_STAT Register fields */
+#define TX_DMA_DONE			BIT(0)
+#define TX_EOT				BIT(1)
+#define TX_SBE				BIT(2)
+#define TX_RESET_DONE			BIT(3)
+
+/* SE_DMA_RX_IRQ_STAT Register fields */
+#define RX_DMA_DONE			BIT(0)
+#define RX_EOT				BIT(1)
+#define RX_SBE				BIT(2)
+#define RX_RESET_DONE			BIT(3)
+#define RX_FLUSH_DONE			BIT(4)
+#define RX_GENI_GP_IRQ			GENMASK(10, 5)
+#define RX_GENI_CANCEL_IRQ		BIT(11)
+#define RX_GENI_GP_IRQ_EXT		GENMASK(13, 12)
+
+/* SE_HW_PARAM_0 fields */
+#define TX_FIFO_WIDTH_MSK		GENMASK(29, 24)
+#define TX_FIFO_WIDTH_SHFT		24
+#define TX_FIFO_DEPTH_MSK		GENMASK(21, 16)
+#define TX_FIFO_DEPTH_SHFT		16
+
+/* SE_HW_PARAM_1 fields */
+#define RX_FIFO_WIDTH_MSK		GENMASK(29, 24)
+#define RX_FIFO_WIDTH_SHFT		24
+#define RX_FIFO_DEPTH_MSK		GENMASK(21, 16)
+#define RX_FIFO_DEPTH_SHFT		16
+
+#define HW_VER_MAJOR_MASK		GENMASK(31, 28)
+#define HW_VER_MAJOR_SHFT		28
+#define HW_VER_MINOR_MASK		GENMASK(27, 16)
+#define HW_VER_MINOR_SHFT		16
+#define HW_VER_STEP_MASK		GENMASK(15, 0)
+
+#if IS_ENABLED(CONFIG_QCOM_GENI_SE)
+
+u32 geni_se_get_qup_hw_version(struct geni_se *se);
+
+#define geni_se_get_wrapper_version(se, major, minor, step) do { \
+	u32 ver; \
+\
+	ver = geni_se_get_qup_hw_version(se); \
+	major = (ver & HW_VER_MAJOR_MASK) >> HW_VER_MAJOR_SHFT; \
+	minor = (ver & HW_VER_MINOR_MASK) >> HW_VER_MINOR_SHFT; \
+	step = version & HW_VER_STEP_MASK; \
+} while (0)
+
+/**
+ * geni_se_read_proto() - Read the protocol configured for a serial engine
+ * @se:		Pointer to the concerned serial engine.
+ *
+ * Return: Protocol value as configured in the serial engine.
+ */
+static inline u32 geni_se_read_proto(struct geni_se *se)
+{
+	u32 val;
+
+	val = readl_relaxed(se->base + GENI_FW_REVISION_RO);
+
+	return (val & FW_REV_PROTOCOL_MSK) >> FW_REV_PROTOCOL_SHFT;
+}
+
+/**
+ * geni_se_setup_m_cmd() - Setup the primary sequencer
+ * @se:		Pointer to the concerned serial engine.
+ * @cmd:	Command/Operation to setup in the primary sequencer.
+ * @params:	Parameter for the sequencer command.
+ *
+ * This function is used to configure the primary sequencer with the
+ * command and its associated parameters.
+ */
+static inline void geni_se_setup_m_cmd(struct geni_se *se, u32 cmd, u32 params)
+{
+	u32 m_cmd;
+
+	m_cmd = (cmd << M_OPCODE_SHFT) | (params & M_PARAMS_MSK);
+	writel_relaxed(m_cmd, se->base + SE_GENI_M_CMD0);
+}
+
+/**
+ * geni_se_setup_s_cmd() - Setup the secondary sequencer
+ * @se:		Pointer to the concerned serial engine.
+ * @cmd:	Command/Operation to setup in the secondary sequencer.
+ * @params:	Parameter for the sequencer command.
+ *
+ * This function is used to configure the secondary sequencer with the
+ * command and its associated parameters.
+ */
+static inline void geni_se_setup_s_cmd(struct geni_se *se, u32 cmd, u32 params)
+{
+	u32 s_cmd;
+
+	s_cmd = readl_relaxed(se->base + SE_GENI_S_CMD0);
+	s_cmd &= ~(S_OPCODE_MSK | S_PARAMS_MSK);
+	s_cmd |= (cmd << S_OPCODE_SHFT);
+	s_cmd |= (params & S_PARAMS_MSK);
+	writel_relaxed(s_cmd, se->base + SE_GENI_S_CMD0);
+}
+
+/**
+ * geni_se_cancel_m_cmd() - Cancel the command configured in the primary
+ *                          sequencer
+ * @se:	Pointer to the concerned serial engine.
+ *
+ * This function is used to cancel the currently configured command in the
+ * primary sequencer.
+ */
+static inline void geni_se_cancel_m_cmd(struct geni_se *se)
+{
+	writel_relaxed(M_GENI_CMD_CANCEL, se->base + SE_GENI_M_CMD_CTRL_REG);
+}
+
+/**
+ * geni_se_cancel_s_cmd() - Cancel the command configured in the secondary
+ *                          sequencer
+ * @se:	Pointer to the concerned serial engine.
+ *
+ * This function is used to cancel the currently configured command in the
+ * secondary sequencer.
+ */
+static inline void geni_se_cancel_s_cmd(struct geni_se *se)
+{
+	writel_relaxed(S_GENI_CMD_CANCEL, se->base + SE_GENI_S_CMD_CTRL_REG);
+}
+
+/**
+ * geni_se_abort_m_cmd() - Abort the command configured in the primary sequencer
+ * @se:	Pointer to the concerned serial engine.
+ *
+ * This function is used to force abort the currently configured command in the
+ * primary sequencer.
+ */
+static inline void geni_se_abort_m_cmd(struct geni_se *se)
+{
+	writel_relaxed(M_GENI_CMD_ABORT, se->base + SE_GENI_M_CMD_CTRL_REG);
+}
+
+/**
+ * geni_se_abort_s_cmd() - Abort the command configured in the secondary
+ *                         sequencer
+ * @se:	Pointer to the concerned serial engine.
+ *
+ * This function is used to force abort the currently configured command in the
+ * secondary sequencer.
+ */
+static inline void geni_se_abort_s_cmd(struct geni_se *se)
+{
+	writel_relaxed(S_GENI_CMD_ABORT, se->base + SE_GENI_S_CMD_CTRL_REG);
+}
+
+/**
+ * geni_se_get_tx_fifo_depth() - Get the TX fifo depth of the serial engine
+ * @se:	Pointer to the concerned serial engine.
+ *
+ * This function is used to get the depth i.e. number of elements in the
+ * TX fifo of the serial engine.
+ *
+ * Return: TX fifo depth in units of FIFO words.
+ */
+static inline u32 geni_se_get_tx_fifo_depth(struct geni_se *se)
+{
+	u32 val;
+
+	val = readl_relaxed(se->base + SE_HW_PARAM_0);
+
+	return (val & TX_FIFO_DEPTH_MSK) >> TX_FIFO_DEPTH_SHFT;
+}
+
+/**
+ * geni_se_get_tx_fifo_width() - Get the TX fifo width of the serial engine
+ * @se:	Pointer to the concerned serial engine.
+ *
+ * This function is used to get the width i.e. word size per element in the
+ * TX fifo of the serial engine.
+ *
+ * Return: TX fifo width in bits
+ */
+static inline u32 geni_se_get_tx_fifo_width(struct geni_se *se)
+{
+	u32 val;
+
+	val = readl_relaxed(se->base + SE_HW_PARAM_0);
+
+	return (val & TX_FIFO_WIDTH_MSK) >> TX_FIFO_WIDTH_SHFT;
+}
+
+/**
+ * geni_se_get_rx_fifo_depth() - Get the RX fifo depth of the serial engine
+ * @se:	Pointer to the concerned serial engine.
+ *
+ * This function is used to get the depth i.e. number of elements in the
+ * RX fifo of the serial engine.
+ *
+ * Return: RX fifo depth in units of FIFO words
+ */
+static inline u32 geni_se_get_rx_fifo_depth(struct geni_se *se)
+{
+	u32 val;
+
+	val = readl_relaxed(se->base + SE_HW_PARAM_1);
+
+	return (val & RX_FIFO_DEPTH_MSK) >> RX_FIFO_DEPTH_SHFT;
+}
+
+void geni_se_init(struct geni_se *se, u32 rx_wm, u32 rx_rfr);
+
+void geni_se_select_mode(struct geni_se *se, enum geni_se_xfer_mode mode);
+
+void geni_se_config_packing(struct geni_se *se, int bpw, int pack_words,
+			    bool msb_to_lsb, bool tx_cfg, bool rx_cfg);
+
+int geni_se_resources_off(struct geni_se *se);
+
+int geni_se_resources_on(struct geni_se *se);
+
+int geni_se_clk_tbl_get(struct geni_se *se, unsigned long **tbl);
+
+int geni_se_clk_freq_match(struct geni_se *se, unsigned long req_freq,
+			   unsigned int *index, unsigned long *res_freq,
+			   bool exact);
+
+int geni_se_tx_dma_prep(struct geni_se *se, void *buf, size_t len,
+			dma_addr_t *iova);
+
+int geni_se_rx_dma_prep(struct geni_se *se, void *buf, size_t len,
+			dma_addr_t *iova);
+
+void geni_se_tx_dma_unprep(struct geni_se *se, dma_addr_t iova, size_t len);
+
+void geni_se_rx_dma_unprep(struct geni_se *se, dma_addr_t iova, size_t len);
+#endif
+#endif
diff --git a/include/linux/soc/qcom/smem.h b/include/linux/soc/qcom/smem.h
index c1657ed27b30..86e1b358688a 100644
--- a/include/linux/soc/qcom/smem.h
+++ b/include/linux/soc/qcom/smem.h
@@ -9,4 +9,6 @@ void *qcom_smem_get(unsigned host, unsigned item, size_t *size);
 
 int qcom_smem_get_free_space(unsigned host);
 
+phys_addr_t qcom_smem_virt_to_phys(void *p);
+
 #endif