diff options
| -rw-r--r-- | Documentation/hwmon/isl68137 | 72 | ||||
| -rw-r--r-- | drivers/hwmon/pmbus/Kconfig | 9 | ||||
| -rw-r--r-- | drivers/hwmon/pmbus/Makefile | 1 | ||||
| -rw-r--r-- | drivers/hwmon/pmbus/isl68137.c | 169 |
4 files changed, 251 insertions, 0 deletions
diff --git a/Documentation/hwmon/isl68137 b/Documentation/hwmon/isl68137 new file mode 100644 index 000000000000..92e5c5fc5b77 --- /dev/null +++ b/Documentation/hwmon/isl68137 @@ -0,0 +1,72 @@ +Kernel driver isl68137 +====================== + +Supported chips: + * Intersil ISL68137 + Prefix: 'isl68137' + Addresses scanned: - + Datasheet: Publicly available at the Intersil website + https://www.intersil.com/content/dam/Intersil/documents/isl6/isl68137.pdf + +Authors: + Maxim Sloyko <maxims@google.com> + Robert Lippert <rlippert@google.com> + Patrick Venture <venture@google.com> + +Description +----------- + +Intersil ISL68137 is a digital output 7-phase configurable PWM +controller with an AVSBus interface. + +Usage Notes +----------- + +This driver does not probe for PMBus devices. You will have to instantiate +devices explicitly. + +The ISL68137 AVS operation mode must be enabled/disabled at runtime. + +Beyond the normal sysfs pmbus attributes, the driver exposes a control attribute. + +Additional Sysfs attributes +--------------------------- + +avs(0|1)_enable Controls the AVS state of each rail. + +curr1_label "iin" +curr1_input Measured input current +curr1_crit Critical maximum current +curr1_crit_alarm Current critical high alarm + +curr[2-3]_label "iout[1-2]" +curr[2-3]_input Measured output current +curr[2-3]_crit Critical maximum current +curr[2-3]_crit_alarm Current critical high alarm + +in1_label "vin" +in1_input Measured input voltage +in1_lcrit Critical minimum input voltage +in1_lcrit_alarm Input voltage critical low alarm +in1_crit Critical maximum input voltage +in1_crit_alarm Input voltage critical high alarm + +in[2-3]_label "vout[1-2]" +in[2-3]_input Measured output voltage +in[2-3]_lcrit Critical minimum output voltage +in[2-3]_lcrit_alarm Output voltage critical low alarm +in[2-3]_crit Critical maximum output voltage +in[2-3]_crit_alarm Output voltage critical high alarm + +power1_label "pin" +power1_input Measured input power +power1_alarm Input power high alarm + +power[2-3]_label "pout[1-2]" +power[2-3]_input Measured output power + +temp[1-3]_input Measured temperature +temp[1-3]_crit Critical high temperature +temp[1-3]_crit_alarm Chip temperature critical high alarm +temp[1-3]_max Maximum temperature +temp[1-3]_max_alarm Chip temperature high alarm diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig index de87abab990e..7edab7e30eaf 100644 --- a/drivers/hwmon/pmbus/Kconfig +++ b/drivers/hwmon/pmbus/Kconfig @@ -63,6 +63,15 @@ config SENSORS_IR38064 This driver can also be built as a module. If so, the module will be called ir38064. +config SENSORS_ISL68137 + tristate "Intersil ISL68137" + help + If you say yes here you get hardware monitoring support for Intersil + ISL68137. + + This driver can also be built as a module. If so, the module will + be called isl68137. + config SENSORS_LM25066 tristate "National Semiconductor LM25066 and compatibles" help diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile index 7d1fa6b3c8c9..2219b9300316 100644 --- a/drivers/hwmon/pmbus/Makefile +++ b/drivers/hwmon/pmbus/Makefile @@ -9,6 +9,7 @@ obj-$(CONFIG_SENSORS_ADM1275) += adm1275.o obj-$(CONFIG_SENSORS_IBM_CFFPS) += ibm-cffps.o obj-$(CONFIG_SENSORS_IR35221) += ir35221.o obj-$(CONFIG_SENSORS_IR38064) += ir38064.o +obj-$(CONFIG_SENSORS_ISL68137) += isl68137.o obj-$(CONFIG_SENSORS_LM25066) += lm25066.o obj-$(CONFIG_SENSORS_LTC2978) += ltc2978.o obj-$(CONFIG_SENSORS_LTC3815) += ltc3815.o diff --git a/drivers/hwmon/pmbus/isl68137.c b/drivers/hwmon/pmbus/isl68137.c new file mode 100644 index 000000000000..515596c92fe1 --- /dev/null +++ b/drivers/hwmon/pmbus/isl68137.c @@ -0,0 +1,169 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Hardware monitoring driver for Intersil ISL68137 + * + * Copyright (c) 2017 Google Inc + * + */ + +#include <linux/err.h> +#include <linux/hwmon-sysfs.h> +#include <linux/i2c.h> +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/string.h> +#include <linux/sysfs.h> +#include "pmbus.h" + +#define ISL68137_VOUT_AVS 0x30 + +static ssize_t isl68137_avs_enable_show_page(struct i2c_client *client, + int page, + char *buf) +{ + int val = pmbus_read_byte_data(client, page, PMBUS_OPERATION); + + return sprintf(buf, "%d\n", + (val & ISL68137_VOUT_AVS) == ISL68137_VOUT_AVS ? 1 : 0); +} + +static ssize_t isl68137_avs_enable_store_page(struct i2c_client *client, + int page, + const char *buf, size_t count) +{ + int rc, op_val; + bool result; + + rc = kstrtobool(buf, &result); + if (rc) + return rc; + + op_val = result ? ISL68137_VOUT_AVS : 0; + + /* + * Writes to VOUT setpoint over AVSBus will persist after the VRM is + * switched to PMBus control. Switching back to AVSBus control + * restores this persisted setpoint rather than re-initializing to + * PMBus VOUT_COMMAND. Writing VOUT_COMMAND first over PMBus before + * enabling AVS control is the workaround. + */ + if (op_val == ISL68137_VOUT_AVS) { + rc = pmbus_read_word_data(client, page, PMBUS_VOUT_COMMAND); + if (rc < 0) + return rc; + + rc = pmbus_write_word_data(client, page, PMBUS_VOUT_COMMAND, + rc); + if (rc < 0) + return rc; + } + + rc = pmbus_update_byte_data(client, page, PMBUS_OPERATION, + ISL68137_VOUT_AVS, op_val); + + return (rc < 0) ? rc : count; +} + +static ssize_t isl68137_avs_enable_show(struct device *dev, + struct device_attribute *devattr, + char *buf) +{ + struct i2c_client *client = to_i2c_client(dev->parent); + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + + return isl68137_avs_enable_show_page(client, attr->index, buf); +} + +static ssize_t isl68137_avs_enable_store(struct device *dev, + struct device_attribute *devattr, + const char *buf, size_t count) +{ + struct i2c_client *client = to_i2c_client(dev->parent); + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + + return isl68137_avs_enable_store_page(client, attr->index, buf, count); +} + +static SENSOR_DEVICE_ATTR_RW(avs0_enable, isl68137_avs_enable, 0); +static SENSOR_DEVICE_ATTR_RW(avs1_enable, isl68137_avs_enable, 1); + +static struct attribute *enable_attrs[] = { + &sensor_dev_attr_avs0_enable.dev_attr.attr, + &sensor_dev_attr_avs1_enable.dev_attr.attr, + NULL, +}; + +static const struct attribute_group enable_group = { + .attrs = enable_attrs, +}; + +static const struct attribute_group *attribute_groups[] = { + &enable_group, + NULL, +}; + +static struct pmbus_driver_info isl68137_info = { + .pages = 2, + .format[PSC_VOLTAGE_IN] = direct, + .format[PSC_VOLTAGE_OUT] = direct, + .format[PSC_CURRENT_IN] = direct, + .format[PSC_CURRENT_OUT] = direct, + .format[PSC_POWER] = direct, + .format[PSC_TEMPERATURE] = direct, + .m[PSC_VOLTAGE_IN] = 1, + .b[PSC_VOLTAGE_IN] = 0, + .R[PSC_VOLTAGE_IN] = 3, + .m[PSC_VOLTAGE_OUT] = 1, + .b[PSC_VOLTAGE_OUT] = 0, + .R[PSC_VOLTAGE_OUT] = 3, + .m[PSC_CURRENT_IN] = 1, + .b[PSC_CURRENT_IN] = 0, + .R[PSC_CURRENT_IN] = 2, + .m[PSC_CURRENT_OUT] = 1, + .b[PSC_CURRENT_OUT] = 0, + .R[PSC_CURRENT_OUT] = 1, + .m[PSC_POWER] = 1, + .b[PSC_POWER] = 0, + .R[PSC_POWER] = 0, + .m[PSC_TEMPERATURE] = 1, + .b[PSC_TEMPERATURE] = 0, + .R[PSC_TEMPERATURE] = 0, + .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_IIN | PMBUS_HAVE_PIN + | PMBUS_HAVE_STATUS_INPUT | PMBUS_HAVE_TEMP | PMBUS_HAVE_TEMP2 + | PMBUS_HAVE_TEMP3 | PMBUS_HAVE_STATUS_TEMP + | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT + | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT | PMBUS_HAVE_POUT, + .func[1] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT + | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT | PMBUS_HAVE_POUT, + .groups = attribute_groups, +}; + +static int isl68137_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + return pmbus_do_probe(client, id, &isl68137_info); +} + +static const struct i2c_device_id isl68137_id[] = { + {"isl68137", 0}, + {} +}; + +MODULE_DEVICE_TABLE(i2c, isl68137_id); + +/* This is the driver that will be inserted */ +static struct i2c_driver isl68137_driver = { + .driver = { + .name = "isl68137", + }, + .probe = isl68137_probe, + .remove = pmbus_do_remove, + .id_table = isl68137_id, +}; + +module_i2c_driver(isl68137_driver); + +MODULE_AUTHOR("Maxim Sloyko <maxims@google.com>"); +MODULE_DESCRIPTION("PMBus driver for Intersil ISL68137"); +MODULE_LICENSE("GPL"); |