diff options
67 files changed, 1703 insertions, 910 deletions
diff --git a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt index b7943f3f9995..dedfb02c744a 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt @@ -22,6 +22,8 @@ Optional properties: - voltage-ranges : two cells are required, first cell specifies minimum slot voltage (mV), second cell specifies maximum slot voltage (mV). Several ranges could be specified. + - little-endian : If the host controller is little-endian mode, specify + this property. The default endian mode is big-endian. Example: diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index 0384fc3f64e8..f693baf87264 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -37,6 +37,7 @@ Optional properties: - sd-uhs-sdr104: SD UHS SDR104 speed is supported - sd-uhs-ddr50: SD UHS DDR50 speed is supported - cap-power-off-card: powering off the card is safe +- cap-mmc-hw-reset: eMMC hardware reset is supported - cap-sdio-irq: enable SDIO IRQ signalling on this interface - full-pwr-cycle: full power cycle of the card is supported - mmc-ddr-1_8v: eMMC high-speed DDR mode(1.8V I/O) is supported diff --git a/Documentation/devicetree/bindings/mmc/mtk-sd.txt b/Documentation/devicetree/bindings/mmc/mtk-sd.txt index a1adfa495ad3..0120c7f1109c 100644 --- a/Documentation/devicetree/bindings/mmc/mtk-sd.txt +++ b/Documentation/devicetree/bindings/mmc/mtk-sd.txt @@ -17,6 +17,11 @@ Required properties: - vmmc-supply: power to the Core - vqmmc-supply: power to the IO +Optional properties: +- assigned-clocks: PLL of the source clock +- assigned-clock-parents: parent of source clock, used for HS400 mode to get 400Mhz source clock +- hs400-ds-delay: HS400 DS delay setting + Examples: mmc0: mmc@11230000 { compatible = "mediatek,mt8173-mmc", "mediatek,mt8135-mmc"; @@ -24,9 +29,13 @@ mmc0: mmc@11230000 { interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_LOW>; vmmc-supply = <&mt6397_vemc_3v3_reg>; vqmmc-supply = <&mt6397_vio18_reg>; - clocks = <&pericfg CLK_PERI_MSDC30_0>, <&topckgen CLK_TOP_MSDC50_0_H_SEL>; + clocks = <&pericfg CLK_PERI_MSDC30_0>, + <&topckgen CLK_TOP_MSDC50_0_H_SEL>; clock-names = "source", "hclk"; pinctrl-names = "default", "state_uhs"; pinctrl-0 = <&mmc0_pins_default>; pinctrl-1 = <&mmc0_pins_uhs>; + assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>; + assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL_D2>; + hs400-ds-delay = <0x14015>; }; diff --git a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt index d38942f6c5ae..cae29eb5733d 100644 --- a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt +++ b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt @@ -6,11 +6,12 @@ and the properties used by the MMCIF device. Required properties: -- compatible: must contain one of the following +- compatible: should be "renesas,mmcif-<soctype>", "renesas,sh-mmcif" as a + fallback. Examples with <soctype> are: - "renesas,mmcif-r8a7740" for the MMCIF found in r8a7740 SoCs - "renesas,mmcif-r8a7790" for the MMCIF found in r8a7790 SoCs - "renesas,mmcif-r8a7791" for the MMCIF found in r8a7791 SoCs - - "renesas,sh-mmcif" for the generic MMCIF + - "renesas,mmcif-r8a7794" for the MMCIF found in r8a7794 SoCs - clocks: reference to the functional clock diff --git a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt index c327c2d6f23d..3dc13b68fc3f 100644 --- a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt @@ -14,6 +14,19 @@ Required Properties: before RK3288 - "rockchip,rk3288-dw-mshc": for Rockchip RK3288 +Optional Properties: +* clocks: from common clock binding: if ciu_drive and ciu_sample are + specified in clock-names, should contain handles to these clocks. + +* clock-names: Apart from the clock-names described in synopsys-dw-mshc.txt + two more clocks "ciu-drive" and "ciu-sample" are supported. They are used + to control the clock phases, "ciu-sample" is required for tuning high- + speed modes. + +* rockchip,default-sample-phase: The default phase to set ciu_sample at + probing, low speeds or in case where all phases work at tuning time. + If not specified 0 deg will be used. + Example: rkdwmmc0@12200000 { diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt index 346c6095a615..8636f5ae97e5 100644 --- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt @@ -75,6 +75,12 @@ Optional properties: * vmmc-supply: The phandle to the regulator to use for vmmc. If this is specified we'll defer probe until we can find this regulator. +* dmas: List of DMA specifiers with the controller specific format as described + in the generic DMA client binding. Refer to dma.txt for details. + +* dma-names: request names for generic DMA client binding. Must be "rx-tx". + Refer to dma.txt for details. + Aliases: - All the MSHC controller nodes should be represented in the aliases node using @@ -95,6 +101,23 @@ board specific portions as listed below. #size-cells = <0>; }; +[board specific internal DMA resources] + + dwmmc0@12200000 { + clock-frequency = <400000000>; + clock-freq-min-max = <400000 200000000>; + num-slots = <1>; + broken-cd; + fifo-depth = <0x80>; + card-detect-delay = <200>; + vmmc-supply = <&buck8>; + bus-width = <8>; + cap-mmc-highspeed; + cap-sd-highspeed; + }; + +[board specific generic DMA request binding] + dwmmc0@12200000 { clock-frequency = <400000000>; clock-freq-min-max = <400000 200000000>; @@ -106,4 +129,6 @@ board specific portions as listed below. bus-width = <8>; cap-mmc-highspeed; cap-sd-highspeed; + dmas = <&pdma 12>; + dma-names = "rx-tx"; }; diff --git a/Documentation/mmc/mmc-dev-attrs.txt b/Documentation/mmc/mmc-dev-attrs.txt index 189bab09255a..caa555706f89 100644 --- a/Documentation/mmc/mmc-dev-attrs.txt +++ b/Documentation/mmc/mmc-dev-attrs.txt @@ -72,13 +72,3 @@ Note on raw_rpmb_size_mult: "raw_rpmb_size_mult" is a mutliple of 128kB block. RPMB size in byte is calculated by using the following equation: RPMB partition size = 128kB x raw_rpmb_size_mult - -SD/MMC/SDIO Clock Gating Attribute -================================== - -Read and write access is provided to following attribute. -This attribute appears only if CONFIG_MMC_CLKGATE is enabled. - - clkgate_delay Tune the clock gating delay with desired value in milliseconds. - -echo <desired delay> > /sys/class/mmc_host/mmcX/clkgate_delay diff --git a/arch/arc/configs/axs101_defconfig b/arch/arc/configs/axs101_defconfig index 562dac6a7f78..c92c0ef1e9d2 100644 --- a/arch/arc/configs/axs101_defconfig +++ b/arch/arc/configs/axs101_defconfig @@ -89,7 +89,6 @@ CONFIG_MMC=y CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_PLTFM=y CONFIG_MMC_DW=y -CONFIG_MMC_DW_IDMAC=y # CONFIG_IOMMU_SUPPORT is not set CONFIG_EXT3_FS=y CONFIG_EXT4_FS=y diff --git a/arch/arc/configs/axs103_defconfig b/arch/arc/configs/axs103_defconfig index 83a6d8d5cc58..cfac24e0e7b6 100644 --- a/arch/arc/configs/axs103_defconfig +++ b/arch/arc/configs/axs103_defconfig @@ -95,7 +95,6 @@ CONFIG_MMC=y CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_PLTFM=y CONFIG_MMC_DW=y -CONFIG_MMC_DW_IDMAC=y # CONFIG_IOMMU_SUPPORT is not set CONFIG_EXT3_FS=y CONFIG_EXT4_FS=y diff --git a/arch/arc/configs/axs103_smp_defconfig b/arch/arc/configs/axs103_smp_defconfig index f1e1c84e0dda..9922a118a15a 100644 --- a/arch/arc/configs/axs103_smp_defconfig +++ b/arch/arc/configs/axs103_smp_defconfig @@ -96,7 +96,6 @@ CONFIG_MMC=y CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_PLTFM=y CONFIG_MMC_DW=y -CONFIG_MMC_DW_IDMAC=y # CONFIG_IOMMU_SUPPORT is not set CONFIG_EXT3_FS=y CONFIG_EXT4_FS=y diff --git a/arch/arm/boot/dts/rk3288-veyron-sdmmc.dtsi b/arch/arm/boot/dts/rk3288-veyron-sdmmc.dtsi index b5334ecff13c..fec076eb7aef 100644 --- a/arch/arm/boot/dts/rk3288-veyron-sdmmc.dtsi +++ b/arch/arm/boot/dts/rk3288-veyron-sdmmc.dtsi @@ -90,7 +90,7 @@ regulators { vccio_sd: LDO_REG4 { regulator-name = "vccio_sd"; - regulator-min-microvolt = <3300000>; + regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; regulator-state-mem { regulator-off-in-suspend; @@ -116,7 +116,12 @@ cap-sd-highspeed; card-detect-delay = <200>; cd-gpios = <&gpio7 5 GPIO_ACTIVE_LOW>; + rockchip,default-sample-phase = <90>; num-slots = <1>; + sd-uhs-sdr12; + sd-uhs-sdr25; + sd-uhs-sdr50; + sd-uhs-sdr104; vmmc-supply = <&vcc33_sd>; vqmmc-supply = <&vccio_sd>; }; diff --git a/arch/arm/boot/dts/rk3288-veyron.dtsi b/arch/arm/boot/dts/rk3288-veyron.dtsi index 275c78ccc0f3..860cea0a7613 100644 --- a/arch/arm/boot/dts/rk3288-veyron.dtsi +++ b/arch/arm/boot/dts/rk3288-veyron.dtsi @@ -149,7 +149,9 @@ broken-cd; bus-width = <8>; cap-mmc-highspeed; + rockchip,default-sample-phase = <158>; disable-wp; + mmc-hs200-1_8v; mmc-pwrseq = <&emmc_pwrseq>; non-removable; num-slots = <1>; @@ -355,6 +357,10 @@ num-slots = <1>; pinctrl-names = "default"; pinctrl-0 = <&sdio0_clk &sdio0_cmd &sdio0_bus4>; + sd-uhs-sdr12; + sd-uhs-sdr25; + sd-uhs-sdr50; + sd-uhs-sdr104; vmmc-supply = <&vcc33_sys>; vqmmc-supply = <&vcc18_wl>; }; diff --git a/arch/arm/boot/dts/rk3288.dtsi b/arch/arm/boot/dts/rk3288.dtsi index 906e938fb6bf..4e7c6b7392af 100644 --- a/arch/arm/boot/dts/rk3288.dtsi +++ b/arch/arm/boot/dts/rk3288.dtsi @@ -222,8 +222,9 @@ sdmmc: dwmmc@ff0c0000 { compatible = "rockchip,rk3288-dw-mshc"; clock-freq-min-max = <400000 150000000>; - clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>; - clock-names = "biu", "ciu"; + clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>, + <&cru SCLK_SDMMC_DRV>, <&cru SCLK_SDMMC_SAMPLE>; + clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; fifo-depth = <0x100>; interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; reg = <0xff0c0000 0x4000>; @@ -233,8 +234,9 @@ sdio0: dwmmc@ff0d0000 { compatible = "rockchip,rk3288-dw-mshc"; clock-freq-min-max = <400000 150000000>; - clocks = <&cru HCLK_SDIO0>, <&cru SCLK_SDIO0>; - clock-names = "biu", "ciu"; + clocks = <&cru HCLK_SDIO0>, <&cru SCLK_SDIO0>, + <&cru SCLK_SDIO0_DRV>, <&cru SCLK_SDIO0_SAMPLE>; + clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; fifo-depth = <0x100>; interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; reg = <0xff0d0000 0x4000>; @@ -244,8 +246,9 @@ sdio1: dwmmc@ff0e0000 { compatible = "rockchip,rk3288-dw-mshc"; clock-freq-min-max = <400000 150000000>; - clocks = <&cru HCLK_SDIO1>, <&cru SCLK_SDIO1>; - clock-names = "biu", "ciu"; + clocks = <&cru HCLK_SDIO1>, <&cru SCLK_SDIO1>, + <&cru SCLK_SDIO1_DRV>, <&cru SCLK_SDIO1_SAMPLE>; + clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; fifo-depth = <0x100>; interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; reg = <0xff0e0000 0x4000>; @@ -255,8 +258,9 @@ emmc: dwmmc@ff0f0000 { compatible = "rockchip,rk3288-dw-mshc"; clock-freq-min-max = <400000 150000000>; - clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>; - clock-names = "biu", "ciu"; + clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>, + <&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>; + clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; fifo-depth = <0x100>; interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; reg = <0xff0f0000 0x4000>; diff --git a/arch/arm/configs/exynos_defconfig b/arch/arm/configs/exynos_defconfig index 1ff2bfa2e183..13ba48c4b03b 100644 --- a/arch/arm/configs/exynos_defconfig +++ b/arch/arm/configs/exynos_defconfig @@ -166,7 +166,6 @@ CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_S3C=y CONFIG_MMC_SDHCI_S3C_DMA=y CONFIG_MMC_DW=y -CONFIG_MMC_DW_IDMAC=y CONFIG_MMC_DW_EXYNOS=y CONFIG_RTC_CLASS=y CONFIG_RTC_DRV_MAX77686=y diff --git a/arch/arm/configs/hisi_defconfig b/arch/arm/configs/hisi_defconfig index 5997dbc69822..b2e340b272ee 100644 --- a/arch/arm/configs/hisi_defconfig +++ b/arch/arm/configs/hisi_defconfig @@ -69,7 +69,6 @@ CONFIG_NOP_USB_XCEIV=y CONFIG_MMC=y CONFIG_RTC_CLASS=y CONFIG_MMC_DW=y -CONFIG_MMC_DW_IDMAC=y CONFIG_MMC_DW_PLTFM=y CONFIG_RTC_DRV_PL031=y CONFIG_DMADEVICES=y diff --git a/arch/arm/configs/lpc18xx_defconfig b/arch/arm/configs/lpc18xx_defconfig index 1c47f86c3970..b7e8cdab51f9 100644 --- a/arch/arm/configs/lpc18xx_defconfig +++ b/arch/arm/configs/lpc18xx_defconfig @@ -119,7 +119,6 @@ CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_ROOT_HUB_TT=y CONFIG_MMC=y CONFIG_MMC_DW=y -CONFIG_MMC_DW_IDMAC=y CONFIG_NEW_LEDS=y CONFIG_LEDS_CLASS=y CONFIG_LEDS_PCA9532=y diff --git a/arch/mips/configs/pistachio_defconfig b/arch/mips/configs/pistachio_defconfig index 642b50946943..8b7429127a1d 100644 --- a/arch/mips/configs/pistachio_defconfig +++ b/arch/mips/configs/pistachio_defconfig @@ -257,7 +257,6 @@ CONFIG_MMC=y CONFIG_MMC_BLOCK_MINORS=16 CONFIG_MMC_TEST=m CONFIG_MMC_DW=y -CONFIG_MMC_DW_IDMAC=y CONFIG_NEW_LEDS=y CONFIG_LEDS_CLASS=y CONFIG_RTC_CLASS=y diff --git a/drivers/clk/rockchip/clk-mmc-phase.c b/drivers/clk/rockchip/clk-mmc-phase.c index 9b613426e968..bc24e5a002e7 100644 --- a/drivers/clk/rockchip/clk-mmc-phase.c +++ b/drivers/clk/rockchip/clk-mmc-phase.c @@ -45,8 +45,8 @@ static unsigned long rockchip_mmc_recalc(struct clk_hw *hw, #define PSECS_PER_SEC 1000000000000LL /* - * Each fine delay is between 40ps-80ps. Assume each fine delay is 60ps to - * simplify calculations. So 45degs could be anywhere between 33deg and 66deg. + * Each fine delay is between 44ps-77ps. Assume each fine delay is 60ps to + * simplify calculations. So 45degs could be anywhere between 33deg and 57.8deg. */ #define ROCKCHIP_MMC_DELAY_ELEMENT_PSEC 60 @@ -69,7 +69,7 @@ static int rockchip_mmc_get_phase(struct clk_hw *hw) delay_num = (raw_value & ROCKCHIP_MMC_DELAYNUM_MASK); delay_num >>= ROCKCHIP_MMC_DELAYNUM_OFFSET; - degrees += delay_num * factor / 10000; + degrees += DIV_ROUND_CLOSEST(delay_num * factor, 10000); } return degrees % 360; @@ -82,25 +82,41 @@ static int rockchip_mmc_set_phase(struct clk_hw *hw, int degrees) u8 nineties, remainder; u8 delay_num; u32 raw_value; - u64 delay; - - /* allow 22 to be 22.5 */ - degrees++; - /* floor to 22.5 increment */ - degrees -= ((degrees) * 10 % 225) / 10; + u32 delay; nineties = degrees / 90; - /* 22.5 multiples */ - remainder = (degrees % 90) / 22; - - delay = PSECS_PER_SEC; - do_div(delay, rate); - /* / 360 / 22.5 */ - do_div(delay, 16); - do_div(delay, ROCKCHIP_MMC_DELAY_ELEMENT_PSEC); - + remainder = (degrees % 90); + + /* + * Due to the inexact nature of the "fine" delay, we might + * actually go non-monotonic. We don't go _too_ monotonic + * though, so we should be OK. Here are options of how we may + * work: + * + * Ideally we end up with: + * 1.0, 2.0, ..., 69.0, 70.0, ..., 89.0, 90.0 + * + * On one extreme (if delay is actually 44ps): + * .73, 1.5, ..., 50.6, 51.3, ..., 65.3, 90.0 + * The other (if delay is actually 77ps): + * 1.3, 2.6, ..., 88.6. 89.8, ..., 114.0, 90 + * + * It's possible we might make a delay that is up to 25 + * degrees off from what we think we're making. That's OK + * though because we should be REALLY far from any bad range. + */ + + /* + * Convert to delay; do a little extra work to make sure we + * don't overflow 32-bit / 64-bit numbers. + */ + delay = 10000000; /* PSECS_PER_SEC / 10000 / 10 */ delay *= remainder; - delay_num = (u8) min(delay, 255ULL); + delay = DIV_ROUND_CLOSEST(delay, + (rate / 1000) * 36 * + (ROCKCHIP_MMC_DELAY_ELEMENT_PSEC / 10)); + + delay_num = (u8) min_t(u32, delay, 255); raw_value = delay_num ? ROCKCHIP_MMC_DELAY_SEL : 0; raw_value |= delay_num << ROCKCHIP_MMC_DELAYNUM_OFFSET; diff --git a/drivers/mmc/card/block.c b/drivers/mmc/card/block.c index c742cfd7674e..23b6c8e8701c 100644 --- a/drivers/mmc/card/block.c +++ b/drivers/mmc/card/block.c @@ -387,6 +387,24 @@ out: return ERR_PTR(err); } +static int mmc_blk_ioctl_copy_to_user(struct mmc_ioc_cmd __user *ic_ptr, + struct mmc_blk_ioc_data *idata) +{ + struct mmc_ioc_cmd *ic = &idata->ic; + + if (copy_to_user(&(ic_ptr->response), ic->response, + sizeof(ic->response))) + return -EFAULT; + + if (!idata->ic.write_flag) { + if (copy_to_user((void __user *)(unsigned long)ic->data_ptr, + idata->buf, idata->buf_bytes)) + return -EFAULT; + } + + return 0; +} + static int ioctl_rpmb_card_status_poll(struct mmc_card *card, u32 *status, u32 retries_max) { @@ -447,12 +465,9 @@ out: return err; } -static int mmc_blk_ioctl_cmd(struct block_device *bdev, - struct mmc_ioc_cmd __user *ic_ptr) +static int __mmc_blk_ioctl_cmd(struct mmc_card *card, struct mmc_blk_data *md, + struct mmc_blk_ioc_data *idata) { - struct mmc_blk_ioc_data *idata; - struct mmc_blk_data *md; - struct mmc_card *card; struct mmc_command cmd = {0}; struct mmc_data data = {0}; struct mmc_request mrq = {NULL}; @@ -461,33 +476,12 @@ static int mmc_blk_ioctl_cmd(struct block_device *bdev, int is_rpmb = false; u32 status = 0; - /* - * The caller must have CAP_SYS_RAWIO, and must be calling this on the - * whole block device, not on a partition. This prevents overspray - * between sibling partitions. - */ - if ((!capable(CAP_SYS_RAWIO)) || (bdev != bdev->bd_contains)) - return -EPERM; - - idata = mmc_blk_ioctl_copy_from_user(ic_ptr); - if (IS_ERR(idata)) - return PTR_ERR(idata); - - md = mmc_blk_get(bdev->bd_disk); - if (!md) { - err = -EINVAL; - goto cmd_err; - } + if (!card || !md || !idata) + return -EINVAL; if (md->area_type & MMC_BLK_DATA_AREA_RPMB) is_rpmb = true; - card = md->queue.card; - if (IS_ERR(card)) { - err = PTR_ERR(card); - goto cmd_done; - } - cmd.opcode = idata->ic.opcode; cmd.arg = idata->ic.arg; cmd.flags = idata->ic.flags; @@ -530,23 +524,21 @@ static int mmc_blk_ioctl_cmd(struct block_device *bdev, mrq.cmd = &cmd; - mmc_get_card(card); - err = mmc_blk_part_switch(card, md); if (err) - goto cmd_rel_host; + return err; if (idata->ic.is_acmd) { err = mmc_app_cmd(card->host, card); if (err) - goto cmd_rel_host; + return err; } if (is_rpmb) { err = mmc_set_blockcount(card, data.blocks, idata->ic.write_flag & (1 << 31)); if (err) - goto cmd_rel_host; + return err; } if ((MMC_EXTRACT_INDEX_FROM_ARG(cmd.arg) == EXT_CSD_SANITIZE_START) && @@ -557,7 +549,7 @@ static int mmc_blk_ioctl_cmd(struct block_device *bdev, pr_err("%s: ioctl_do_sanitize() failed. err = %d", __func__, err); - goto cmd_rel_host; + return err; } mmc_wait_for_req(card->host, &mrq); @@ -565,14 +557,12 @@ static int mmc_blk_ioctl_cmd(struct block_device *bdev, if (cmd.error) { dev_err(mmc_dev(card->host), "%s: cmd error %d\n", __func__, cmd.error); - err = cmd.error; - goto cmd_rel_host; + return cmd.error; } if (data.error) { dev_err(mmc_dev(card->host), "%s: data error %d\n", __func__, data.error); - err = data.error; - goto cmd_rel_host; + return data.error; } /* @@ -582,18 +572,7 @@ static int mmc_blk_ioctl_cmd(struct block_device *bdev, if (idata->ic.postsleep_min_us) usleep_range(idata->ic.postsleep_min_us, idata->ic.postsleep_max_us); - if (copy_to_user(&(ic_ptr->response), cmd.resp, sizeof(cmd.resp))) { - err = -EFAULT; - goto cmd_rel_host; - } - - if (!idata->ic.write_flag) { - if (copy_to_user((void __user *)(unsigned long) idata->ic.data_ptr, - idata->buf, idata->buf_bytes)) { - err = -EFAULT; - goto cmd_rel_host; - } - } + memcpy(&(idata->ic.response), cmd.resp, sizeof(cmd.resp)); if (is_rpmb) { /* @@ -607,24 +586,132 @@ static int mmc_blk_ioctl_cmd(struct block_device *bdev, __func__, status, err); } -cmd_rel_host: + return err; +} + +static int mmc_blk_ioctl_cmd(struct block_device *bdev, + struct mmc_ioc_cmd __user *ic_ptr) +{ + struct mmc_blk_ioc_data *idata; + struct mmc_blk_data *md; + struct mmc_card *card; + int err = 0, ioc_err = 0; + + idata = mmc_blk_ioctl_copy_from_user(ic_ptr); + if (IS_ERR(idata)) + return PTR_ERR(idata); + + md = mmc_blk_get(bdev->bd_disk); + if (!md) { + err = -EINVAL; + goto cmd_err; + } + + card = md->queue.card; + if (IS_ERR(card)) { + err = PTR_ERR(card); + goto cmd_done; + } + + mmc_get_card(card); + + ioc_err = __mmc_blk_ioctl_cmd(card, md, idata); + mmc_put_card(card); + err = mmc_blk_ioctl_copy_to_user(ic_ptr, idata); + cmd_done: mmc_blk_put(md); cmd_err: kfree(idata->buf); kfree(idata); - return err; + return ioc_err ? ioc_err : err; +} + +static int mmc_blk_ioctl_multi_cmd(struct block_device *bdev, + struct mmc_ioc_multi_cmd __user *user) +{ + struct mmc_blk_ioc_data **idata = NULL; + struct mmc_ioc_cmd __user *cmds = user->cmds; + struct mmc_card *card; + struct mmc_blk_data *md; + int i, err = 0, ioc_err = 0; + __u64 num_of_cmds; + + if (copy_from_user(&num_of_cmds, &user->num_of_cmds, + sizeof(num_of_cmds))) + return -EFAULT; + + if (num_of_cmds > MMC_IOC_MAX_CMDS) + return -EINVAL; + + idata = kcalloc(num_of_cmds, sizeof(*idata), GFP_KERNEL); + if (!idata) + return -ENOMEM; + + for (i = 0; i < num_of_cmds; i++) { + idata[i] = mmc_blk_ioctl_copy_from_user(&cmds[i]); + if (IS_ERR(idata[i])) { + err = PTR_ERR(idata[i]); + num_of_cmds = i; + goto cmd_err; + } + } + + md = mmc_blk_get(bdev->bd_disk); + if (!md) + goto cmd_err; + + card = md->queue.card; + if (IS_ERR(card)) { + err = PTR_ERR(card); + goto cmd_done; + } + + mmc_get_card(card); + + for (i = 0; i < num_of_cmds && !ioc_err; i++) + ioc_err = __mmc_blk_ioctl_cmd(card, md, idata[i]); + + mmc_put_card(card); + + /* copy to user if data and response */ + for (i = 0; i < num_of_cmds && !err; i++) + err = mmc_blk_ioctl_copy_to_user(&cmds[i], idata[i]); + +cmd_done: + mmc_blk_put(md); +cmd_err: + for (i = 0; i < num_of_cmds; i++) { + kfree(idata[i]->buf); + kfree(idata[i]); + } + kfree(idata); + return ioc_err ? ioc_err : err; } static int mmc_blk_ioctl(struct block_device *bdev, fmode_t mode, unsigned int cmd, unsigned long arg) { - int ret = -EINVAL; - if (cmd == MMC_IOC_CMD) - ret = mmc_blk_ioctl_cmd(bdev, (struct mmc_ioc_cmd __user *)arg); - return ret; + /* + * The caller must have CAP_SYS_RAWIO, and must be calling this on the + * whole block device, not on a partition. This prevents overspray + * between sibling partitions. + */ + if ((!capable(CAP_SYS_RAWIO)) || (bdev != bdev->bd_contains)) + return -EPERM; + + switch (cmd) { + case MMC_IOC_CMD: + return mmc_blk_ioctl_cmd(bdev, + (struct mmc_ioc_cmd __user *)arg); + case MMC_IOC_MULTI_CMD: + return mmc_blk_ioctl_multi_cmd(bdev, + (struct mmc_ioc_multi_cmd __user *)arg); + default: + return -EINVAL; + } } #ifdef CONFIG_COMPAT diff --git a/drivers/mmc/core/Kconfig b/drivers/mmc/core/Kconfig index 9ebee72d9c3f..4c33d7690f2f 100644 --- a/drivers/mmc/core/Kconfig +++ b/drivers/mmc/core/Kconfig @@ -1,13 +1,3 @@ # # MMC core configuration # - -config MMC_CLKGATE - bool "MMC host clock gating" - help - This will attempt to aggressively gate the clock to the MMC card. - This is done to save power due to gating off the logic and bus - noise when the MMC card is not in use. Your host driver has to - support handling this in order for it to be of any use. - - If unsure, say N. diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c index a3eb20bdcd97..5ae89e48fd85 100644 --- a/drivers/mmc/core/core.c +++ b/drivers/mmc/core/core.c @@ -187,8 +187,6 @@ void mmc_request_done(struct mmc_host *host, struct mmc_request *mrq) if (mrq->done) mrq->done(mrq); - - mmc_host_clk_release(host); } } @@ -206,6 +204,23 @@ static void __mmc_start_request(struct mmc_host *host, struct mmc_request *mrq) return; } + /* + * For sdio rw commands we must wait for card busy otherwise some + * sdio devices won't work properly. + */ + if (mmc_is_io_op(mrq->cmd->opcode) && host->ops->card_busy) { + int tries = 500; /* Wait aprox 500ms at maximum */ + + while (host->ops->card_busy(host) && --tries) + mmc_delay(1); + + if (tries == 0) { + mrq->cmd->error = -EBUSY; + mmc_request_done(host, mrq); + return; + } + } + host->ops->request(host, mrq); } @@ -275,7 +290,6 @@ static int mmc_start_request(struct mmc_host *host, struct mmc_request *mrq) mrq->stop->mrq = mrq; } } - mmc_host_clk_hold(host); led_trigger_event(host->led, LED_FULL); __mmc_start_request(host, mrq); @@ -525,11 +539,8 @@ static void mmc_wait_for_req_done(struct mmc_host *host, static void mmc_pre_req(struct mmc_host *host, struct mmc_request *mrq, bool is_first_req) { - if (host->ops->pre_req) { - mmc_host_clk_hold(host); + if (host->ops->pre_req) host->ops->pre_req(host, mrq, is_first_req); - mmc_host_clk_release(host); - } } /** @@ -544,11 +555,8 @@ static void mmc_pre_req(struct mmc_host *host, struct mmc_request *mrq, static void mmc_post_req(struct mmc_host *host, struct mmc_request *mrq, int err) { - if (host->ops->post_req) { - mmc_host_clk_hold(host); + if (host->ops->post_req) host->ops->post_req(host, mrq, err); - mmc_host_clk_release(host); - } } /** @@ -833,9 +841,9 @@ void mmc_set_data_timeout(struct mmc_data *data, const struct mmc_card *card) unsigned int timeout_us, limit_us; timeout_us = data->timeout_ns / 1000; - if (mmc_host_clk_rate(card->host)) + if (card->host->ios.clock) timeout_us += data->timeout_clks * 1000 / - (mmc_host_clk_rate(card->host) / 1000); + (card->host->ios.clock / 1000); if (data->flags & MMC_DATA_WRITE) /* @@ -1033,8 +1041,6 @@ static inline void mmc_set_ios(struct mmc_host *host) ios->power_mode, ios->chip_select, ios->vdd, ios->bus_width, ios->timing); - if (ios->clock > 0) - mmc_set_ungated(host); host->ops->set_ios(host, ios); } @@ -1043,17 +1049,15 @@ static inline void mmc_set_ios(struct mmc_host *host) */ void mmc_set_chip_select(struct mmc_host *host, int mode) { - mmc_host_clk_hold(host); host->ios.chip_select = mode; mmc_set_ios(host); - mmc_host_clk_release(host); } /* * Sets the host clock to the highest possible frequency that * is below "hz". */ -static void __mmc_set_clock(struct mmc_host *host, unsigned int hz) +void mmc_set_clock(struct mmc_host *host, unsigned int hz) { WARN_ON(hz && hz < host->f_min); @@ -1064,68 +1068,6 @@ static void __mmc_set_clock(struct mmc_host *host, unsigned int hz) mmc_set_ios(host); } -void mmc_set_clock(struct mmc_host *host, unsigned int hz) -{ - mmc_host_clk_hold(host); - __mmc_set_clock(host, hz); - mmc_host_clk_release(host); -} - -#ifdef CONFIG_MMC_CLKGATE -/* - * This gates the clock by setting it to 0 Hz. - */ -void mmc_gate_clock(struct mmc_host *host) -{ - unsigned long flags; - - spin_lock_irqsave(&host->clk_lock, flags); - host->clk_old = host->ios.clock; - host->ios.clock = 0; - host->clk_gated = true; - spin_unlock_irqrestore(&host->clk_lock, flags); - mmc_set_ios(host); -} - -/* - * This restores the clock from gating by using the cached - * clock value. - */ -void mmc_ungate_clock(struct mmc_host *host) -{ - /* - * We should previously have gated the clock, so the clock shall - * be 0 here! The clock may however be 0 during initialization, - * when some request operations are performed before setting - * the frequency. When ungate is requested in that situation - * we just ignore the call. - */ - if (host->clk_old) { - BUG_ON(host->ios.clock); - /* This call will also set host->clk_gated to false */ - __mmc_set_clock(host, host->clk_old); - } -} - -void mmc_set_ungated(struct mmc_host *host) -{ - unsigned long flags; - - /* - * We've been given a new frequency while the clock is gated, - * so make sure we regard this as ungating it. - */ - spin_lock_irqsave(&host->clk_lock, flags); - host->clk_gated = false; - spin_unlock_irqrestore(&host->clk_lock, flags); -} - -#else -void mmc_set_ungated(struct mmc_host *host) -{ -} -#endif - int mmc_execute_tuning(struct mmc_card *card) { struct mmc_host *host = card->host; @@ -1140,9 +1082,7 @@ int mmc_execute_tuning(struct mmc_card *card) else opcode = MMC_SEND_TUNING_BLOCK; - mmc_host_clk_hold(host); err = host->ops->execute_tuning(host, opcode); - mmc_host_clk_release(host); if (err) pr_err("%s: tuning execution failed\n", mmc_hostname(host)); @@ -1157,10 +1097,8 @@ int mmc_execute_tuning(struct mmc_card *card) */ void mmc_set_bus_mode(struct mmc_host *host, unsigned int mode) { - mmc_host_clk_hold(host); host->ios.bus_mode = mode; mmc_set_ios(host); - mmc_host_clk_release(host); } /* @@ -1168,10 +1106,8 @@ void mmc_set_bus_mode(struct mmc_host *host, unsigned int mode) */ void mmc_set_bus_width(struct mmc_host *host, unsigned int width) { - mmc_host_clk_hold(host); host->ios.bus_width = width; mmc_set_ios(host); - mmc_host_clk_release(host); } /* @@ -1341,6 +1277,40 @@ struct device_node *mmc_of_find_child_device(struct mmc_host *host, #ifdef CONFIG_REGULATOR /** + * mmc_ocrbitnum_to_vdd - Convert a OCR bit number to its voltage + * @vdd_bit: OCR bit number + * @min_uV: minimum voltage value (mV) + * @max_uV: maximum voltage value (mV) + * + * This function returns the voltage range according to the provided OCR + * bit number. If conversion is not possible a negative errno value returned. + */ +static int mmc_ocrbitnum_to_vdd(int vdd_bit, int *min_uV, int *max_uV) +{ + int tmp; + + if (!vdd_bit) + return -EINVAL; + + /* + * REVISIT mmc_vddrange_to_ocrmask() may have set some + * bits this regulator doesn't quite support ... don't + * be too picky, most cards and regulators are OK with + * a 0.1V range goof (it's a small error percentage). + */ + tmp = vdd_bit - ilog2(MMC_VDD_165_195); + if (tmp == 0) { + *min_uV = 1650 * 1000; + *max_uV = 1950 * 1000; + } else { + *min_uV = 1900 * 1000 + tmp * 100 * 1000; + *max_uV = *min_uV + 100 * 1000; + } + + return 0; +} + +/** * mmc_regulator_get_ocrmask - return mask of supported voltages * @supply: regulator to use * @@ -1403,22 +1373,7 @@ int mmc_regulator_set_ocr(struct mmc_host *mmc, int min_uV, max_uV; if (vdd_bit) { - int tmp; - - /* - * REVISIT mmc_vddrange_to_ocrmask() may have set some - * bits this regulator doesn't quite support ... don't - * be too picky, most cards and regulators are OK with - * a 0.1V range goof (it's a small error percentage). - */ - tmp = vdd_bit - ilog2(MMC_VDD_165_195); - if (tmp == 0) { - min_uV = 1650 * 1000; - max_uV = 1950 * 1000; - } else { - min_uV = 1900 * 1000 + tmp * 100 * 1000; - max_uV = min_uV + 100 * 1000; - } + mmc_ocrbitnum_to_vdd(vdd_bit, &min_uV, &max_uV); result = regulator_set_voltage(supply, min_uV, max_uV); if (result == 0 && !mmc->regulator_enabled) { @@ -1439,6 +1394,84 @@ int mmc_regulator_set_ocr(struct mmc_host *mmc, } EXPORT_SYMBOL_GPL(mmc_regulator_set_ocr); +static int mmc_regulator_set_voltage_if_supported(struct regulator *regulator, + int min_uV, int target_uV, + int max_uV) +{ + /* + * Check if supported first to avoid errors since we may try several + * signal levels during power up and don't want to show errors. + */ + if (!regulator_is_supported_voltage(regulator, min_uV, max_uV)) + return -EINVAL; + + return regulator_set_voltage_triplet(regulator, min_uV, target_uV, + max_uV); +} + +/** + * mmc_regulator_set_vqmmc - Set VQMMC as per the ios + * + * For 3.3V signaling, we try to match VQMMC to VMMC as closely as possible. + * That will match the behavior of old boards where VQMMC and VMMC were supplied + * by the same supply. The Bus Operating conditions for 3.3V signaling in the + * SD card spec also define VQMMC in terms of VMMC. + * If this is not possible we'll try the full 2.7-3.6V of the spec. + * + * For 1.2V and 1.8V signaling we'll try to get as close as possible to the + * requested voltage. This is definitely a good idea for UHS where there's a + * separate regulator on the card that's trying to make 1.8V and it's best if + * we match. + * + * This function is expected to be used by a controller's + * start_signal_voltage_switch() function. + */ +int mmc_regulator_set_vqmmc(struct mmc_host *mmc, struct mmc_ios *ios) +{ + struct device *dev = mmc_dev(mmc); + int ret, volt, min_uV, max_uV; + + /* If no vqmmc supply then we can't change the voltage */ + if (IS_ERR(mmc->supply.vqmmc)) + return -EINVAL; + + switch (ios->signal_voltage) { + case MMC_SIGNAL_VOLTAGE_120: + return mmc_regulator_set_voltage_if_supported(mmc->supply.vqmmc, + 1100000, 1200000, 1300000); + case MMC_SIGNAL_VOLTAGE_180: + return mmc_regulator_set_voltage_if_supported(mmc->supply.vqmmc, + 1700000, 1800000, 1950000); + case MMC_SIGNAL_VOLTAGE_330: + ret = mmc_ocrbitnum_to_vdd(mmc->ios.vdd, &volt, &max_uV); + if (ret < 0) + return ret; + + dev_dbg(dev, "%s: found vmmc voltage range of %d-%duV\n", + __func__, volt, max_uV); + + min_uV = max(volt - 300000, 2700000); + max_uV = min(max_uV + 200000, 3600000); + + /* + * Due to a limitation in the current implementation of + * regulator_set_voltage_triplet() which is taking the lowest + * voltage possible if below the target, search for a suitable + * voltage in two steps and try to stay close to vmmc + * with a 0.3V tolerance at first. + */ + if (!mmc_regulator_set_voltage_if_supported(mmc->supply.vqmmc, + min_uV, volt, max_uV)) + return 0; + + return mmc_regulator_set_voltage_if_supported(mmc->supply.vqmmc, + 2700000, volt, 3600000); + default: + return -EINVAL; + } +} +EXPORT_SYMBOL_GPL(mmc_regulator_set_vqmmc); + #endif /* CONFIG_REGULATOR */ int mmc_regulator_get_supply(struct mmc_host *mmc) @@ -1515,11 +1548,8 @@ int __mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage) int old_signal_voltage = host->ios.signal_voltage; host->ios.signal_voltage = signal_voltage; - if (host->ops->start_signal_voltage_switch) { - mmc_host_clk_hold(host); + if (host->ops->start_signal_voltage_switch) err = host->ops->start_signal_voltage_switch(host, &host->ios); - mmc_host_clk_release(host); - } if (err) host->ios.signal_voltage = old_signal_voltage; @@ -1553,20 +1583,17 @@ int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage, u32 ocr) pr_warn("%s: cannot verify signal voltage switch\n", mmc_hostname(host)); - mmc_host_clk_hold(host); - cmd.opcode = SD_SWITCH_VOLTAGE; cmd.arg = 0; cmd.flags = MMC_RSP_R1 | MMC_CMD_AC; err = mmc_wait_for_cmd(host, &cmd, 0); if (err) - goto err_command; + return err; + + if (!mmc_host_is_spi(host) && (cmd.resp[0] & R1_ERROR)) + return -EIO; - if (!mmc_host_is_spi(host) && (cmd.resp[0] & R1_ERROR)) { - err = -EIO; - goto err_command; - } /* * The card should drive cmd and dat[0:3] low immediately * after the response of cmd11, but wait 1 ms to be sure @@ -1615,9 +1642,6 @@ power_cycle: mmc_power_cycle(host, ocr); } -err_command: - mmc_host_clk_release(host); - return err; } @@ -1626,10 +1650,8 @@ err_command: */ void mmc_set_timing(struct mmc_host *host, unsigned int timing) { - mmc_host_clk_hold(host); host->ios.timing = timing; mmc_set_ios(host); - mmc_host_clk_release(host); } /* @@ -1637,10 +1659,8 @@ void mmc_set_timing(struct mmc_host *host, unsigned int timing) */ void mmc_set_driver_type(struct mmc_host *host, unsigned int drv_type) { - mmc_host_clk_hold(host); host->ios.drv_type = drv_type; mmc_set_ios(host); - mmc_host_clk_release(host); } int mmc_select_drive_strength(struct mmc_card *card, unsigned int max_dtr, @@ -1648,7 +1668,6 @@ int mmc_select_drive_strength(struct mmc_card *card, unsigned int max_dtr, { struct mmc_host *host = card->host; int host_drv_type = SD_DRIVER_TYPE_B; - int drive_strength; *drv_type = 0; @@ -1671,14 +1690,10 @@ int mmc_select_drive_strength(struct mmc_card *card, unsigned int max_dtr, * information and let the hardware specific code * return what is possible given the options */ - mmc_host_clk_hold(host); - drive_strength = host->ops->select_drive_strength(card, max_dtr, - host_drv_type, - card_drv_type, - drv_type); - mmc_host_clk_release(host); - - return drive_strength; + return host->ops->select_drive_strength(card, max_dtr, + host_drv_type, + card_drv_type, + drv_type); } /* @@ -1697,8 +1712,6 @@ void mmc_power_up(struct mmc_host *host, u32 ocr) if (host->ios.power_mode == MMC_POWER_ON) return; - mmc_host_clk_hold(host); - mmc_pwrseq_pre_power_on(host); host->ios.vdd = fls(ocr) - 1; @@ -1732,8 +1745,6 @@ void mmc_power_up(struct mmc_host *host, u32 ocr) * time required to reach a stable voltage. */ mmc_delay(10); - - mmc_host_clk_release(host); } void mmc_power_off(struct mmc_host *host) @@ -1741,8 +1752,6 @@ void mmc_power_off(struct mmc_host *host) if (host->ios.power_mode == MMC_POWER_OFF) return; - mmc_host_clk_hold(host); - mmc_pwrseq_power_off(host); host->ios.clock = 0; @@ -1758,8 +1767,6 @@ void mmc_power_off(struct mmc_host *host) * can be successfully turned on again. */ mmc_delay(1); - - mmc_host_clk_release(host); } void mmc_power_cycle(struct mmc_host *host, u32 ocr) @@ -1975,7 +1982,7 @@ static unsigned int mmc_mmc_erase_timeout(struct mmc_card *card, */ timeout_clks <<= 1; timeout_us += (timeout_clks * 1000) / - (mmc_host_clk_rate(card->host) / 1000); + (card->host->ios.clock / 1000); erase_timeout = timeout_us / 1000; @@ -2423,9 +2430,7 @@ static void mmc_hw_reset_for_init(struct mmc_host *host) { if (!(host->caps & MMC_CAP_HW_RESET) || !host->ops->hw_reset) return; - mmc_host_clk_hold(host); host->ops->hw_reset(host); - mmc_host_clk_release(host); } int mmc_hw_reset(struct mmc_host *host) @@ -2633,10 +2638,14 @@ void mmc_start_host(struct mmc_host *host) host->f_init = max(freqs[0], host->f_min); host->rescan_disable = 0; host->ios.power_mode = MMC_POWER_UNDEFINED; + + mmc_claim_host(host); if (host->caps2 & MMC_CAP2_NO_PRESCAN_POWERUP) mmc_power_off(host); else mmc_power_up(host, host->ocr_avail); + mmc_release_host(host); + mmc_gpiod_request_cd_irq(host); _mmc_detect_change(host, 0, false); } @@ -2674,7 +2683,9 @@ void mmc_stop_host(struct mmc_host *host) BUG_ON(host->card); + mmc_claim_host(host); mmc_power_off(host); + mmc_release_host(host); } int mmc_power_save_host(struct mmc_host *host) diff --git a/drivers/mmc/core/core.h b/drivers/mmc/core/core.h index 1a22a82209b2..09241e56d628 100644 --- a/drivers/mmc/core/core.h +++ b/drivers/mmc/core/core.h @@ -40,9 +40,6 @@ void mmc_init_erase(struct mmc_card *card); void mmc_set_chip_select(struct mmc_host *host, int mode); void mmc_set_clock(struct mmc_host *host, unsigned int hz); -void mmc_gate_clock(struct mmc_host *host); -void mmc_ungate_clock(struct mmc_host *host); -void mmc_set_ungated(struct mmc_host *host); void mmc_set_bus_mode(struct mmc_host *host, unsigned int mode); void mmc_set_bus_width(struct mmc_host *host, unsigned int width); u32 mmc_select_voltage(struct mmc_host *host, u32 ocr); diff --git a/drivers/mmc/core/debugfs.c b/drivers/mmc/core/debugfs.c index e9142108a6c6..154aced0b91b 100644 --- a/drivers/mmc/core/debugfs.c +++ b/drivers/mmc/core/debugfs.c @@ -126,6 +126,12 @@ static int mmc_ios_show(struct seq_file *s, void *data) case MMC_TIMING_SD_HS: str = "sd high-speed"; break; + case MMC_TIMING_UHS_SDR12: + str = "sd uhs SDR12"; + break; + case MMC_TIMING_UHS_SDR25: + str = "sd uhs SDR25"; + break; case MMC_TIMING_UHS_SDR50: str = "sd uhs SDR50"; break; @@ -166,6 +172,25 @@ static int mmc_ios_show(struct seq_file *s, void *data) } seq_printf(s, "signal voltage:\t%u (%s)\n", ios->chip_select, str); + switch (ios->drv_type) { + case MMC_SET_DRIVER_TYPE_A: + str = "driver type A"; + break; + case MMC_SET_DRIVER_TYPE_B: + str = "driver type B"; + break; + case MMC_SET_DRIVER_TYPE_C: + str = "driver type C"; + break; + case MMC_SET_DRIVER_TYPE_D: + str = "driver type D"; + break; + default: + str = "invalid"; + break; + } + seq_printf(s, "driver type:\t%u (%s)\n", ios->drv_type, str); + return 0; } @@ -230,11 +255,6 @@ void mmc_add_host_debugfs(struct mmc_host *host) &mmc_clock_fops)) goto err_node; -#ifdef CONFIG_MMC_CLKGATE - if (!debugfs_create_u32("clk_delay", (S_IRUSR | S_IWUSR), - root, &host->clk_delay)) - goto err_node; -#endif #ifdef CONFIG_FAIL_MMC_REQUEST if (fail_request) setup_fault_attr(&fail_default_attr, fail_request); diff --git a/drivers/mmc/core/host.c b/drivers/mmc/core/host.c index 5466f25f0281..da950c44204d 100644 --- a/drivers/mmc/core/host.c +++ b/drivers/mmc/core/host.c @@ -61,246 +61,6 @@ void mmc_unregister_host_class(void) class_unregister(&mmc_host_class); } -#ifdef CONFIG_MMC_CLKGATE -static ssize_t clkgate_delay_show(struct device *dev, - struct device_attribute *attr, char *buf) -{ - struct mmc_host *host = cls_dev_to_mmc_host(dev); - return snprintf(buf, PAGE_SIZE, "%lu\n", host->clkgate_delay); -} - -static ssize_t clkgate_delay_store(struct device *dev, - struct device_attribute *attr, const char *buf, size_t count) -{ - struct mmc_host *host = cls_dev_to_mmc_host(dev); - unsigned long flags, value; - - if (kstrtoul(buf, 0, &value)) - return -EINVAL; - - spin_lock_irqsave(&host->clk_lock, flags); - host->clkgate_delay = value; - spin_unlock_irqrestore(&host->clk_lock, flags); - return count; -} - -/* - * Enabling clock gating will make the core call out to the host - * once up and once down when it performs a request or card operation - * intermingled in any fashion. The driver will see this through - * set_ios() operations with ios.clock field set to 0 to gate (disable) - * the block clock, and to the old frequency to enable it again. - */ -static void mmc_host_clk_gate_delayed(struct mmc_host *host) -{ - unsigned long tick_ns; - unsigned long freq = host->ios.clock; - unsigned long flags; - - if (!freq) { - pr_debug("%s: frequency set to 0 in disable function, " - "this means the clock is already disabled.\n", - mmc_hostname(host)); - return; - } - /* - * New requests may have appeared while we were scheduling, - * then there is no reason to delay the check before - * clk_disable(). - */ - spin_lock_irqsave(&host->clk_lock, flags); - - /* - * Delay n bus cycles (at least 8 from MMC spec) before attempting - * to disable the MCI block clock. The reference count may have - * gone up again after this delay due to rescheduling! - */ - if (!host->clk_requests) { - spin_unlock_irqrestore(&host->clk_lock, flags); - tick_ns = DIV_ROUND_UP(1000000000, freq); - ndelay(host->clk_delay * tick_ns); - } else { - /* New users appeared while waiting for this work */ - spin_unlock_irqrestore(&host->clk_lock, flags); - return; - } - mutex_lock(&host->clk_gate_mutex); - spin_lock_irqsave(&host->clk_lock, flags); - if (!host->clk_requests) { - spin_unlock_irqrestore(&host->clk_lock, flags); - /* This will set host->ios.clock to 0 */ - mmc_gate_clock(host); - spin_lock_irqsave(&host->clk_lock, flags); - pr_debug("%s: gated MCI clock\n", mmc_hostname(host)); - } - spin_unlock_irqrestore(&host->clk_lock, flags); - mutex_unlock(&host->clk_gate_mutex); -} - -/* - * Internal work. Work to disable the clock at some later point. - */ -static void mmc_host_clk_gate_work(struct work_struct *work) -{ - struct mmc_host *host = container_of(work, struct mmc_host, - clk_gate_work.work); - - mmc_host_clk_gate_delayed(host); -} - -/** - * mmc_host_clk_hold - ungate hardware MCI clocks - * @host: host to ungate. - * - * Makes sure the host ios.clock is restored to a non-zero value - * past this call. Increase clock reference count and ungate clock - * if we're the first user. - */ -void mmc_host_clk_hold(struct mmc_host *host) -{ - unsigned long flags; - - /* cancel any clock gating work scheduled by mmc_host_clk_release() */ - cancel_delayed_work_sync(&host->clk_gate_work); - mutex_lock(&host->clk_gate_mutex); - spin_lock_irqsave(&host->clk_lock, flags); - if (host->clk_gated) { - spin_unlock_irqrestore(&host->clk_lock, flags); - mmc_ungate_clock(host); - spin_lock_irqsave(&host->clk_lock, flags); - pr_debug("%s: ungated MCI clock\n", mmc_hostname(host)); - } - host->clk_requests++; - spin_unlock_irqrestore(&host->clk_lock, flags); - mutex_unlock(&host->clk_gate_mutex); -} - -/** - * mmc_host_may_gate_card - check if this card may be gated - * @card: card to check. - */ -static bool mmc_host_may_gate_card(struct mmc_card *card) -{ - /* If there is no card we may gate it */ - if (!card) - return true; - /* - * Don't gate SDIO cards! These need to be clocked at all times - * since they may be independent systems generating interrupts - * and other events. The clock requests counter from the core will - * go down to zero since the core does not need it, but we will not - * gate the clock, because there is somebody out there that may still - * be using it. - */ - return !(card->quirks & MMC_QUIRK_BROKEN_CLK_GATING); -} - -/** - * mmc_host_clk_release - gate off hardware MCI clocks - * @host: host to gate. - * - * Calls the host driver with ios.clock set to zero as often as possible - * in order to gate off hardware MCI clocks. Decrease clock reference - * count and schedule disabling of clock. - */ -void mmc_host_clk_release(struct mmc_host *host) -{ - unsigned long flags; - - spin_lock_irqsave(&host->clk_lock, flags); - host->clk_requests--; - if (mmc_host_may_gate_card(host->card) && - !host->clk_requests) - schedule_delayed_work(&host->clk_gate_work, - msecs_to_jiffies(host->clkgate_delay)); - spin_unlock_irqrestore(&host->clk_lock, flags); -} - -/** - * mmc_host_clk_rate - get current clock frequency setting - * @host: host to get the clock frequency for. - * - * Returns current clock frequency regardless of gating. - */ -unsigned int mmc_host_clk_rate(struct mmc_host *host) -{ - unsigned long freq; - unsigned long flags; - - spin_lock_irqsave(&host->clk_lock, flags); - if (host->clk_gated) - freq = host->clk_old; - else - freq = host->ios.clock; - spin_unlock_irqrestore(&host->clk_lock, flags); - return freq; -} - -/** - * mmc_host_clk_init - set up clock gating code - * @host: host with potential clock to control - */ -static inline void mmc_host_clk_init(struct mmc_host *host) -{ - host->clk_requests = 0; - /* Hold MCI clock for 8 cycles by default */ - host->clk_delay = 8; - /* - * Default clock gating delay is 0ms to avoid wasting power. - * This value can be tuned by writing into sysfs entry. - */ - host->clkgate_delay = 0; - host->clk_gated = false; - INIT_DELAYED_WORK(&host->clk_gate_work, mmc_host_clk_gate_work); - spin_lock_init(&host->clk_lock); - mutex_init(&host->clk_gate_mutex); -} - -/** - * mmc_host_clk_exit - shut down clock gating code - * @host: host with potential clock to control - */ -static inline void mmc_host_clk_exit(struct mmc_host *host) -{ - /* - * Wait for any outstanding gate and then make sure we're - * ungated before exiting. - */ - if (cancel_delayed_work_sync(&host->clk_gate_work)) - mmc_host_clk_gate_delayed(host); - if (host->clk_gated) - mmc_host_clk_hold(host); - /* There should be only one user now */ - WARN_ON(host->clk_requests > 1); -} - -static inline void mmc_host_clk_sysfs_init(struct mmc_host *host) -{ - host->clkgate_delay_attr.show = clkgate_delay_show; - host->clkgate_delay_attr.store = clkgate_delay_store; - sysfs_attr_init(&host->clkgate_delay_attr.attr); - host->clkgate_delay_attr.attr.name = "clkgate_delay"; - host->clkgate_delay_attr.attr.mode = S_IRUGO | S_IWUSR; - if (device_create_file(&host->class_dev, &host->clkgate_delay_attr)) - pr_err("%s: Failed to create clkgate_delay sysfs entry\n", - mmc_hostname(host)); -} -#else - -static inline void mmc_host_clk_init(struct mmc_host *host) -{ -} - -static inline void mmc_host_clk_exit(struct mmc_host *host) -{ -} - -static inline void mmc_host_clk_sysfs_init(struct mmc_host *host) -{ -} - -#endif - void mmc_retune_enable(struct mmc_host *host) { host->can_retune = 1; @@ -507,6 +267,8 @@ int mmc_of_parse(struct mmc_host *host) host->caps |= MMC_CAP_UHS_DDR50; if (of_property_read_bool(np, "cap-power-off-card")) host->caps |= MMC_CAP_POWER_OFF_CARD; + if (of_property_read_bool(np, "cap-mmc-hw-reset")) + host->caps |= MMC_CAP_HW_RESET; if (of_property_read_bool(np, "cap-sdio-irq")) host->caps |= MMC_CAP_SDIO_IRQ; if (of_property_read_bool(np, "full-pwr-cycle")) @@ -583,8 +345,6 @@ struct mmc_host *mmc_alloc_host(int extra, struct device *dev) return NULL; } - mmc_host_clk_init(host); - spin_lock_init(&host->lock); init_waitqueue_head(&host->wq); INIT_DELAYED_WORK(&host->detect, mmc_rescan); @@ -633,7 +393,6 @@ int mmc_add_host(struct mmc_host *host) #ifdef CONFIG_DEBUG_FS mmc_add_host_debugfs(host); #endif - mmc_host_clk_sysfs_init(host); mmc_start_host(host); register_pm_notifier(&host->pm_notify); @@ -663,8 +422,6 @@ void mmc_remove_host(struct mmc_host *host) device_del(&host->class_dev); led_trigger_unregister_simple(host->led); - - mmc_host_clk_exit(host); } EXPORT_SYMBOL(mmc_remove_host); diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c index f6cd995dbe92..c793fda27321 100644 --- a/drivers/mmc/core/mmc.c +++ b/drivers/mmc/core/mmc.c @@ -1931,14 +1931,12 @@ static int mmc_reset(struct mmc_host *host) if (!mmc_can_reset(card)) return -EOPNOTSUPP; - mmc_host_clk_hold(host); mmc_set_clock(host, host->f_init); host->ops->hw_reset(host); /* Set initial state and call mmc_set_ios */ mmc_set_initial_state(host); - mmc_host_clk_release(host); return mmc_init_card(host, card->ocr, card); } @@ -2006,14 +2004,13 @@ int mmc_attach_mmc(struct mmc_host *host) mmc_release_host(host); err = mmc_add_card(host->card); - mmc_claim_host(host); if (err) goto remove_card; + mmc_claim_host(host); return 0; remove_card: - mmc_release_host(host); mmc_remove_card(host->card); mmc_claim_host(host); host->card = NULL; diff --git a/drivers/mmc/core/mmc_ops.c b/drivers/mmc/core/mmc_ops.c index 0e9ae1c276c8..1f444269ebbe 100644 --- a/drivers/mmc/core/mmc_ops.c +++ b/drivers/mmc/core/mmc_ops.c @@ -579,7 +579,6 @@ out: return err; } -EXPORT_SYMBOL_GPL(__mmc_switch); int mmc_switch(struct mmc_card *card, u8 set, u8 index, u8 value, unsigned int timeout_ms) @@ -589,7 +588,7 @@ int mmc_switch(struct mmc_card *card, u8 set, u8 index, u8 value, } EXPORT_SYMBOL_GPL(mmc_switch); -int mmc_send_tuning(struct mmc_host *host) +int mmc_send_tuning(struct mmc_host *host, u32 opcode, int *cmd_error) { struct mmc_request mrq = {NULL}; struct mmc_command cmd = {0}; @@ -599,16 +598,13 @@ int mmc_send_tuning(struct mmc_host *host) const u8 *tuning_block_pattern; int size, err = 0; u8 *data_buf; - u32 opcode; if (ios->bus_width == MMC_BUS_WIDTH_8) { tuning_block_pattern = tuning_blk_pattern_8bit; size = sizeof(tuning_blk_pattern_8bit); - opcode = MMC_SEND_TUNING_BLOCK_HS200; } else if (ios->bus_width == MMC_BUS_WIDTH_4) { tuning_block_pattern = tuning_blk_pattern_4bit; size = sizeof(tuning_blk_pattern_4bit); - opcode = MMC_SEND_TUNING_BLOCK; } else return -EINVAL; @@ -639,6 +635,9 @@ int mmc_send_tuning(struct mmc_host *host) mmc_wait_for_req(host, &mrq); + if (cmd_error) + *cmd_error = cmd.error; + if (cmd.error) { err = cmd.error; goto out; diff --git a/drivers/mmc/core/mmc_ops.h b/drivers/mmc/core/mmc_ops.h index f498f9ae21f0..f1b8e81aaa28 100644 --- a/drivers/mmc/core/mmc_ops.h +++ b/drivers/mmc/core/mmc_ops.h @@ -28,6 +28,9 @@ int mmc_bus_test(struct mmc_card *card, u8 bus_width); int mmc_send_hpi_cmd(struct mmc_card *card, u32 *status); int mmc_can_ext_csd(struct mmc_card *card); int mmc_switch_status_error(struct mmc_host *host, u32 status); +int __mmc_switch(struct mmc_card *card, u8 set, u8 index, u8 value, + unsigned int timeout_ms, bool use_busy_signal, bool send_status, + bool ignore_crc); #endif diff --git a/drivers/mmc/core/pwrseq_emmc.c b/drivers/mmc/core/pwrseq_emmc.c index 9d6d2fb21796..ad4f94ec7e8d 100644 --- a/drivers/mmc/core/pwrseq_emmc.c +++ b/drivers/mmc/core/pwrseq_emmc.c @@ -76,7 +76,7 @@ struct mmc_pwrseq *mmc_pwrseq_emmc_alloc(struct mmc_host *host, if (!pwrseq) return ERR_PTR(-ENOMEM); - pwrseq->reset_gpio = gpiod_get_index(dev, "reset", 0, GPIOD_OUT_LOW); + pwrseq->reset_gpio = gpiod_get(dev, "reset", GPIOD_OUT_LOW); if (IS_ERR(pwrseq->reset_gpio)) { ret = PTR_ERR(pwrseq->reset_gpio); goto free; @@ -84,11 +84,11 @@ struct mmc_pwrseq *mmc_pwrseq_emmc_alloc(struct mmc_host *host, /* * register reset handler to ensure emmc reset also from - * emergency_reboot(), priority 129 schedules it just before - * system reboot + * emergency_reboot(), priority 255 is the highest priority + * so it will be executed before any system reboot handler. */ pwrseq->reset_nb.notifier_call = mmc_pwrseq_emmc_reset_nb; - pwrseq->reset_nb.priority = 129; + pwrseq->reset_nb.priority = 255; register_restart_handler(&pwrseq->reset_nb); pwrseq->pwrseq.ops = &mmc_pwrseq_emmc_ops; diff --git a/drivers/mmc/core/pwrseq_simple.c b/drivers/mmc/core/pwrseq_simple.c index 0b14b83a53d6..d10538bb5e07 100644 --- a/drivers/mmc/core/pwrseq_simple.c +++ b/drivers/mmc/core/pwrseq_simple.c @@ -23,18 +23,21 @@ struct mmc_pwrseq_simple { struct mmc_pwrseq pwrseq; bool clk_enabled; struct clk *ext_clk; - int nr_gpios; - struct gpio_desc *reset_gpios[0]; + struct gpio_descs *reset_gpios; }; static void mmc_pwrseq_simple_set_gpios_value(struct mmc_pwrseq_simple *pwrseq, int value) { int i; + struct gpio_descs *reset_gpios = pwrseq->reset_gpios; + int values[reset_gpios->ndescs]; - for (i = 0; i < pwrseq->nr_gpios; i++) - if (!IS_ERR(pwrseq->reset_gpios[i])) - gpiod_set_value_cansleep(pwrseq->reset_gpios[i], value); + for (i = 0; i < reset_gpios->ndescs; i++) + values[i] = value; + + gpiod_set_array_value_cansleep(reset_gpios->ndescs, reset_gpios->desc, + values); } static void mmc_pwrseq_simple_pre_power_on(struct mmc_host *host) @@ -75,11 +78,8 @@ static void mmc_pwrseq_simple_free(struct mmc_host *host) { struct mmc_pwrseq_simple *pwrseq = container_of(host->pwrseq, struct mmc_pwrseq_simple, pwrseq); - int i; - for (i = 0; i < pwrseq->nr_gpios; i++) - if (!IS_ERR(pwrseq->reset_gpios[i])) - gpiod_put(pwrseq->reset_gpios[i]); + gpiod_put_array(pwrseq->reset_gpios); if (!IS_ERR(pwrseq->ext_clk)) clk_put(pwrseq->ext_clk); @@ -98,14 +98,9 @@ struct mmc_pwrseq *mmc_pwrseq_simple_alloc(struct mmc_host *host, struct device *dev) { struct mmc_pwrseq_simple *pwrseq; - int i, nr_gpios, ret = 0; - - nr_gpios = of_gpio_named_count(dev->of_node, "reset-gpios"); - if (nr_gpios < 0) - nr_gpios = 0; + int ret = 0; - pwrseq = kzalloc(sizeof(struct mmc_pwrseq_simple) + nr_gpios * - sizeof(struct gpio_desc *), GFP_KERNEL); + pwrseq = kzalloc(sizeof(*pwrseq), GFP_KERNEL); if (!pwrseq) return ERR_PTR(-ENOMEM); @@ -116,22 +111,12 @@ struct mmc_pwrseq *mmc_pwrseq_simple_alloc(struct mmc_host *host, goto free; } - for (i = 0; i < nr_gpios; i++) { - pwrseq->reset_gpios[i] = gpiod_get_index(dev, "reset", i, - GPIOD_OUT_HIGH); - if (IS_ERR(pwrseq->reset_gpios[i]) && - PTR_ERR(pwrseq->reset_gpios[i]) != -ENOENT && - PTR_ERR(pwrseq->reset_gpios[i]) != -ENOSYS) { - ret = PTR_ERR(pwrseq->reset_gpios[i]); - - while (i--) - gpiod_put(pwrseq->reset_gpios[i]); - - goto clk_put; - } + pwrseq->reset_gpios = gpiod_get_array(dev, "reset", GPIOD_OUT_HIGH); + if (IS_ERR(pwrseq->reset_gpios)) { + ret = PTR_ERR(pwrseq->reset_gpios); + goto clk_put; } - pwrseq->nr_gpios = nr_gpios; pwrseq->pwrseq.ops = &mmc_pwrseq_simple_ops; return &pwrseq->pwrseq; diff --git a/drivers/mmc/core/quirks.c b/drivers/mmc/core/quirks.c index dd1d1e0fe322..fad660b95809 100644 --- a/drivers/mmc/core/quirks.c +++ b/drivers/mmc/core/quirks.c @@ -35,25 +35,7 @@ #define SDIO_DEVICE_ID_MARVELL_8797_F0 0x9128 #endif -/* - * This hook just adds a quirk for all sdio devices - */ -static void add_quirk_for_sdio_devices(struct mmc_card *card, int data) -{ - if (mmc_card_sdio(card)) - card->quirks |= data; -} - static const struct mmc_fixup mmc_fixup_methods[] = { - /* by default sdio devices are considered CLK_GATING broken */ - /* good cards will be whitelisted as they are tested */ - SDIO_FIXUP(SDIO_ANY_ID, SDIO_ANY_ID, - add_quirk_for_sdio_devices, - MMC_QUIRK_BROKEN_CLK_GATING), - - SDIO_FIXUP(SDIO_VENDOR_ID_TI, SDIO_DEVICE_ID_TI_WL1271, - remove_quirk, MMC_QUIRK_BROKEN_CLK_GATING), - SDIO_FIXUP(SDIO_VENDOR_ID_TI, SDIO_DEVICE_ID_TI_WL1271, add_quirk, MMC_QUIRK_NONSTD_FUNC_IF), diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c index 4e7366ab187f..141eaa923e18 100644 --- a/drivers/mmc/core/sd.c +++ b/drivers/mmc/core/sd.c @@ -357,8 +357,6 @@ int mmc_sd_switch_hs(struct mmc_card *card) if (card->sw_caps.hs_max_dtr == 0) return 0; - err = -EIO; - status = kmalloc(64, GFP_KERNEL); if (!status) { pr_err("%s: could not allocate a buffer for " @@ -628,9 +626,25 @@ static int mmc_sd_init_uhs_card(struct mmc_card *card) * SDR104 mode SD-cards. Note that tuning is mandatory for SDR104. */ if (!mmc_host_is_spi(card->host) && - (card->sd_bus_speed == UHS_SDR50_BUS_SPEED || - card->sd_bus_speed == UHS_SDR104_BUS_SPEED)) + (card->sd_bus_speed == UHS_SDR50_BUS_SPEED || + card->sd_bus_speed == UHS_DDR50_BUS_SPEED || + card->sd_bus_speed == UHS_SDR104_BUS_SPEED)) { err = mmc_execute_tuning(card); + + /* + * As SD Specifications Part1 Physical Layer Specification + * Version 3.01 says, CMD19 tuning is available for unlocked + * cards in transfer state of 1.8V signaling mode. The small + * difference between v3.00 and 3.01 spec means that CMD19 + * tuning is also available for DDR50 mode. + */ + if (err && card->sd_bus_speed == UHS_DDR50_BUS_SPEED) { + pr_warn("%s: ddr50 tuning failed\n", + mmc_hostname(card->host)); + err = 0; + } + } + out: kfree(status); @@ -786,9 +800,7 @@ static int mmc_sd_get_ro(struct mmc_host *host) if (!host->ops->get_ro) return -1; - mmc_host_clk_hold(host); ro = host->ops->get_ro(host); - mmc_host_clk_release(host); return ro; } @@ -1231,14 +1243,13 @@ int mmc_attach_sd(struct mmc_host *host) mmc_release_host(host); err = mmc_add_card(host->card); - mmc_claim_host(host); if (err) goto remove_card; + mmc_claim_host(host); return 0; remove_card: - mmc_release_host(host); mmc_remove_card(host->card); host->card = NULL; mmc_claim_host(host); diff --git a/drivers/mmc/core/sdio.c b/drivers/mmc/core/sdio.c index b91abedcfdca..16d838e6d623 100644 --- a/drivers/mmc/core/sdio.c +++ b/drivers/mmc/core/sdio.c @@ -897,11 +897,10 @@ static int mmc_sdio_pre_suspend(struct mmc_host *host) */ static int mmc_sdio_suspend(struct mmc_host *host) { - if (mmc_card_keep_power(host) && mmc_card_wake_sdio_irq(host)) { - mmc_claim_host(host); + mmc_claim_host(host); + + if (mmc_card_keep_power(host) && mmc_card_wake_sdio_irq(host)) sdio_disable_wide(host->card); - mmc_release_host(host); - } if (!mmc_card_keep_power(host)) { mmc_power_off(host); @@ -910,6 +909,8 @@ static int mmc_sdio_suspend(struct mmc_host *host) mmc_retune_needed(host); } + mmc_release_host(host); + return 0; } @@ -955,13 +956,10 @@ static int mmc_sdio_resume(struct mmc_host *host) } if (!err && host->sdio_irqs) { - if (!(host->caps2 & MMC_CAP2_SDIO_IRQ_NOTHREAD)) { + if (!(host->caps2 & MMC_CAP2_SDIO_IRQ_NOTHREAD)) wake_up_process(host->sdio_irq_thread); - } else if (host->caps & MMC_CAP_SDIO_IRQ) { - mmc_host_clk_hold(host); + else if (host->caps & MMC_CAP_SDIO_IRQ) host->ops->enable_sdio_irq(host, 1); - mmc_host_clk_release(host); - } } mmc_release_host(host); @@ -1018,15 +1016,24 @@ out: static int mmc_sdio_runtime_suspend(struct mmc_host *host) { /* No references to the card, cut the power to it. */ + mmc_claim_host(host); mmc_power_off(host); + mmc_release_host(host); + return 0; } static int mmc_sdio_runtime_resume(struct mmc_host *host) { + int ret; + /* Restore power and re-initialize. */ + mmc_claim_host(host); mmc_power_up(host, host->card->ocr); - return mmc_sdio_power_restore(host); + ret = mmc_sdio_power_restore(host); + mmc_release_host(host); + + return ret; } static int mmc_sdio_reset(struct mmc_host *host) diff --git a/drivers/mmc/core/sdio_irq.c b/drivers/mmc/core/sdio_irq.c index 09cc67d028f0..91bbbfb29f3f 100644 --- a/drivers/mmc/core/sdio_irq.c +++ b/drivers/mmc/core/sdio_irq.c @@ -168,21 +168,15 @@ static int sdio_irq_thread(void *_host) } set_current_state(TASK_INTERRUPTIBLE); - if (host->caps & MMC_CAP_SDIO_IRQ) { - mmc_host_clk_hold(host); + if (host->caps & MMC_CAP_SDIO_IRQ) host->ops->enable_sdio_irq(host, 1); - mmc_host_clk_release(host); - } if (!kthread_should_stop()) schedule_timeout(period); set_current_state(TASK_RUNNING); } while (!kthread_should_stop()); - if (host->caps & MMC_CAP_SDIO_IRQ) { - mmc_host_clk_hold(host); + if (host->caps & MMC_CAP_SDIO_IRQ) host->ops->enable_sdio_irq(host, 0); - mmc_host_clk_release(host); - } pr_debug("%s: IRQ thread exiting with code %d\n", mmc_hostname(host), ret); @@ -208,9 +202,7 @@ static int sdio_card_irq_get(struct mmc_card *card) return err; } } else if (host->caps & MMC_CAP_SDIO_IRQ) { - mmc_host_clk_hold(host); host->ops->enable_sdio_irq(host, 1); - mmc_host_clk_release(host); } } @@ -229,9 +221,7 @@ static int sdio_card_irq_put(struct mmc_card *card) atomic_set(&host->sdio_irq_thread_abort, 1); kthread_stop(host->sdio_irq_thread); } else if (host->caps & MMC_CAP_SDIO_IRQ) { - mmc_host_clk_hold(host); host->ops->enable_sdio_irq(host, 0); - mmc_host_clk_release(host); } } diff --git a/drivers/mmc/core/sdio_ops.h b/drivers/mmc/core/sdio_ops.h index 12a4d3ab174c..5660c7f459e9 100644 --- a/drivers/mmc/core/sdio_ops.h +++ b/drivers/mmc/core/sdio_ops.h @@ -12,6 +12,8 @@ #ifndef _MMC_SDIO_OPS_H #define _MMC_SDIO_OPS_H +#include <linux/mmc/sdio.h> + int mmc_send_io_op_cond(struct mmc_host *host, u32 ocr, u32 *rocr); int mmc_io_rw_direct(struct mmc_card *card, int write, unsigned fn, unsigned addr, u8 in, u8* out); @@ -19,5 +21,10 @@ int mmc_io_rw_extended(struct mmc_card *card, int write, unsigned fn, unsigned addr, int incr_addr, u8 *buf, unsigned blocks, unsigned blksz); int sdio_reset(struct mmc_host *host); +static inline bool mmc_is_io_op(u32 opcode) +{ + return opcode == SD_IO_RW_DIRECT || opcode == SD_IO_RW_EXTENDED; +} + #endif diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig index 8a1e3498261e..af71de5fda3b 100644 --- a/drivers/mmc/host/Kconfig +++ b/drivers/mmc/host/Kconfig @@ -67,7 +67,7 @@ config MMC_SDHCI_BIG_ENDIAN_32BIT_BYTE_SWAPPER has the effect of scrambling the addresses and formats of data accessed in sizes other than the datum size. - This is the case for the Freescale eSDHC and Nintendo Wii SDHCI. + This is the case for the Nintendo Wii SDHCI. config MMC_SDHCI_PCI tristate "SDHCI support on PCI bus" @@ -140,8 +140,8 @@ config MMC_SDHCI_OF_AT91 config MMC_SDHCI_OF_ESDHC tristate "SDHCI OF support for the Freescale eSDHC controller" depends on MMC_SDHCI_PLTFM - depends on PPC - select MMC_SDHCI_BIG_ENDIAN_32BIT_BYTE_SWAPPER + depends on PPC || ARCH_MXC || ARCH_LAYERSCAPE + select MMC_SDHCI_IO_ACCESSORS help This selects the Freescale eSDHC controller support. @@ -366,7 +366,7 @@ config MMC_OMAP config MMC_OMAP_HS tristate "TI OMAP High Speed Multimedia Card Interface support" depends on HAS_DMA - depends on ARCH_OMAP2PLUS || COMPILE_TEST + depends on ARCH_OMAP2PLUS || ARCH_KEYSTONE || COMPILE_TEST help This selects the TI OMAP High Speed Multimedia card Interface. If you have an omap2plus board with a Multimedia Card slot, @@ -473,7 +473,7 @@ config MMC_DAVINCI config MMC_GOLDFISH tristate "goldfish qemu Multimedia Card Interface support" - depends on GOLDFISH + depends on GOLDFISH || COMPILE_TEST help This selects the Goldfish Multimedia card Interface emulation found on the Goldfish Android virtual device emulation. @@ -615,15 +615,7 @@ config MMC_DW help This selects support for the Synopsys DesignWare Mobile Storage IP block, this provides host support for SD and MMC interfaces, in both - PIO and external DMA modes. - -config MMC_DW_IDMAC - bool "Internal DMAC interface" - depends on MMC_DW - help - This selects support for the internal DMAC block within the Synopsys - Designware Mobile Storage IP block. This disables the external DMA - interface. + PIO, internal DMA mode and external DMA mode. config MMC_DW_PLTFM tristate "Synopsys Designware MCI Support as platform device" @@ -652,7 +644,6 @@ config MMC_DW_K3 tristate "K3 specific extensions for Synopsys DW Memory Card Interface" depends on MMC_DW select MMC_DW_PLTFM - select MMC_DW_IDMAC help This selects support for Hisilicon K3 SoC specific extensions to the Synopsys DesignWare Memory Card Interface driver. Select this option diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile index 4f3452afa6ca..3595f83e89dd 100644 --- a/drivers/mmc/host/Makefile +++ b/drivers/mmc/host/Makefile @@ -9,8 +9,8 @@ obj-$(CONFIG_MMC_MXC) += mxcmmc.o obj-$(CONFIG_MMC_MXS) += mxs-mmc.o obj-$(CONFIG_MMC_SDHCI) += sdhci.o obj-$(CONFIG_MMC_SDHCI_PCI) += sdhci-pci.o +sdhci-pci-y += sdhci-pci-core.o sdhci-pci-o2micro.o obj-$(subst m,y,$(CONFIG_MMC_SDHCI_PCI)) += sdhci-pci-data.o -obj-$(subst m,y,$(CONFIG_MMC_SDHCI_PCI)) += sdhci-pci-o2micro.o obj-$(CONFIG_MMC_SDHCI_ACPI) += sdhci-acpi.o obj-$(CONFIG_MMC_SDHCI_PXAV3) += sdhci-pxav3.o obj-$(CONFIG_MMC_SDHCI_PXAV2) += sdhci-pxav2.o diff --git a/drivers/mmc/host/dw_mmc-exynos.c b/drivers/mmc/host/dw_mmc-exynos.c index 1e75309898b7..3a7e835a0033 100644 --- a/drivers/mmc/host/dw_mmc-exynos.c +++ b/drivers/mmc/host/dw_mmc-exynos.c @@ -446,7 +446,7 @@ out: return loc; } -static int dw_mci_exynos_execute_tuning(struct dw_mci_slot *slot) +static int dw_mci_exynos_execute_tuning(struct dw_mci_slot *slot, u32 opcode) { struct dw_mci *host = slot->host; struct dw_mci_exynos_priv_data *priv = host->priv; @@ -461,7 +461,7 @@ static int dw_mci_exynos_execute_tuning(struct dw_mci_slot *slot) mci_writel(host, TMOUT, ~0); smpl = dw_mci_exynos_move_next_clksmpl(host); - if (!mmc_send_tuning(mmc)) + if (!mmc_send_tuning(mmc, opcode, NULL)) candiates |= (1 << smpl); } while (start_smpl != smpl); diff --git a/drivers/mmc/host/dw_mmc-pltfm.c b/drivers/mmc/host/dw_mmc-pltfm.c index ec6dbcdec693..7e1d13b68b06 100644 --- a/drivers/mmc/host/dw_mmc-pltfm.c +++ b/drivers/mmc/host/dw_mmc-pltfm.c @@ -59,6 +59,8 @@ int dw_mci_pltfm_register(struct platform_device *pdev, host->pdata = pdev->dev.platform_data; regs = platform_get_resource(pdev, IORESOURCE_MEM, 0); + /* Get registers' physical base address */ + host->phy_regs = (void *)(regs->start); host->regs = devm_ioremap_resource(&pdev->dev, regs); if (IS_ERR(host->regs)) return PTR_ERR(host->regs); diff --git a/drivers/mmc/host/dw_mmc-rockchip.c b/drivers/mmc/host/dw_mmc-rockchip.c index bc76aa22473e..9becebeeccd1 100644 --- a/drivers/mmc/host/dw_mmc-rockchip.c +++ b/drivers/mmc/host/dw_mmc-rockchip.c @@ -13,12 +13,19 @@ #include <linux/mmc/host.h> #include <linux/mmc/dw_mmc.h> #include <linux/of_address.h> +#include <linux/slab.h> #include "dw_mmc.h" #include "dw_mmc-pltfm.h" #define RK3288_CLKGEN_DIV 2 +struct dw_mci_rockchip_priv_data { + struct clk *drv_clk; + struct clk *sample_clk; + int default_sample_phase; +}; + static void dw_mci_rockchip_prepare_command(struct dw_mci *host, u32 *cmdr) { *cmdr |= SDMMC_CMD_USE_HOLD_REG; @@ -33,6 +40,7 @@ static int dw_mci_rk3288_setup_clock(struct dw_mci *host) static void dw_mci_rk3288_set_ios(struct dw_mci *host, struct mmc_ios *ios) { + struct dw_mci_rockchip_priv_data *priv = host->priv; int ret; unsigned int cclkin; u32 bus_hz; @@ -66,6 +74,158 @@ static void dw_mci_rk3288_set_ios(struct dw_mci *host, struct mmc_ios *ios) /* force dw_mci_setup_bus() */ host->current_speed = 0; } + + /* Make sure we use phases which we can enumerate with */ + if (!IS_ERR(priv->sample_clk)) + clk_set_phase(priv->sample_clk, priv->default_sample_phase); +} + +#define NUM_PHASES 360 +#define TUNING_ITERATION_TO_PHASE(i) (DIV_ROUND_UP((i) * 360, NUM_PHASES)) + +static int dw_mci_rk3288_execute_tuning(struct dw_mci_slot *slot, u32 opcode) +{ + struct dw_mci *host = slot->host; + struct dw_mci_rockchip_priv_data *priv = host->priv; + struct mmc_host *mmc = slot->mmc; + int ret = 0; + int i; + bool v, prev_v = 0, first_v; + struct range_t { + int start; + int end; /* inclusive */ + }; + struct range_t *ranges; + unsigned int range_count = 0; + int longest_range_len = -1; + int longest_range = -1; + int middle_phase; + + if (IS_ERR(priv->sample_clk)) { + dev_err(host->dev, "Tuning clock (sample_clk) not defined.\n"); + return -EIO; + } + + ranges = kmalloc_array(NUM_PHASES / 2 + 1, sizeof(*ranges), GFP_KERNEL); + if (!ranges) + return -ENOMEM; + + /* Try each phase and extract good ranges */ + for (i = 0; i < NUM_PHASES; ) { + clk_set_phase(priv->sample_clk, TUNING_ITERATION_TO_PHASE(i)); + + v = !mmc_send_tuning(mmc, opcode, NULL); + + if (i == 0) + first_v = v; + + if ((!prev_v) && v) { + range_count++; + ranges[range_count-1].start = i; + } + if (v) { + ranges[range_count-1].end = i; + i++; + } else if (i == NUM_PHASES - 1) { + /* No extra skipping rules if we're at the end */ + i++; + } else { + /* + * No need to check too close to an invalid + * one since testing bad phases is slow. Skip + * 20 degrees. + */ + i += DIV_ROUND_UP(20 * NUM_PHASES, 360); + + /* Always test the last one */ + if (i >= NUM_PHASES) + i = NUM_PHASES - 1; + } + + prev_v = v; + } + + if (range_count == 0) { + dev_warn(host->dev, "All phases bad!"); + ret = -EIO; + goto free; + } + + /* wrap around case, merge the end points */ + if ((range_count > 1) && first_v && v) { + ranges[0].start = ranges[range_count-1].start; + range_count--; + } + + if (ranges[0].start == 0 && ranges[0].end == NUM_PHASES - 1) { + clk_set_phase(priv->sample_clk, priv->default_sample_phase); + dev_info(host->dev, "All phases work, using default phase %d.", + priv->default_sample_phase); + goto free; + } + + /* Find the longest range */ + for (i = 0; i < range_count; i++) { + int len = (ranges[i].end - ranges[i].start + 1); + + if (len < 0) + len += NUM_PHASES; + + if (longest_range_len < len) { + longest_range_len = len; + longest_range = i; + } + + dev_dbg(host->dev, "Good phase range %d-%d (%d len)\n", + TUNING_ITERATION_TO_PHASE(ranges[i].start), + TUNING_ITERATION_TO_PHASE(ranges[i].end), + len + ); + } + + dev_dbg(host->dev, "Best phase range %d-%d (%d len)\n", + TUNING_ITERATION_TO_PHASE(ranges[longest_range].start), + TUNING_ITERATION_TO_PHASE(ranges[longest_range].end), + longest_range_len + ); + + middle_phase = ranges[longest_range].start + longest_range_len / 2; + middle_phase %= NUM_PHASES; + dev_info(host->dev, "Successfully tuned phase to %d\n", + TUNING_ITERATION_TO_PHASE(middle_phase)); + + clk_set_phase(priv->sample_clk, + TUNING_ITERATION_TO_PHASE(middle_phase)); + +free: + kfree(ranges); + return ret; +} + +static int dw_mci_rk3288_parse_dt(struct dw_mci *host) +{ + struct device_node *np = host->dev->of_node; + struct dw_mci_rockchip_priv_data *priv; + + priv = devm_kzalloc(host->dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + if (of_property_read_u32(np, "rockchip,default-sample-phase", + &priv->default_sample_phase)) + priv->default_sample_phase = 0; + + priv->drv_clk = devm_clk_get(host->dev, "ciu-drive"); + if (IS_ERR(priv->drv_clk)) + dev_dbg(host->dev, "ciu_drv not available\n"); + + priv->sample_clk = devm_clk_get(host->dev, "ciu-sample"); + if (IS_ERR(priv->sample_clk)) + dev_dbg(host->dev, "ciu_sample not available\n"); + + host->priv = priv; + + return 0; } static int dw_mci_rockchip_init(struct dw_mci *host) @@ -95,6 +255,8 @@ static const struct dw_mci_drv_data rk3288_drv_data = { .caps = dw_mci_rk3288_dwmmc_caps, .prepare_command = dw_mci_rockchip_prepare_command, .set_ios = dw_mci_rk3288_set_ios, + .execute_tuning = dw_mci_rk3288_execute_tuning, + .parse_dt = dw_mci_rk3288_parse_dt, .setup_clock = dw_mci_rk3288_setup_clock, .init = dw_mci_rockchip_init, }; diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c index fcbf5524fd31..7a6cedbe48a8 100644 --- a/drivers/mmc/host/dw_mmc.c +++ b/drivers/mmc/host/dw_mmc.c @@ -56,7 +56,6 @@ #define DW_MCI_FREQ_MAX 200000000 /* unit: HZ */ #define DW_MCI_FREQ_MIN 400000 /* unit: HZ */ -#ifdef CONFIG_MMC_DW_IDMAC #define IDMAC_INT_CLR (SDMMC_IDMAC_INT_AI | SDMMC_IDMAC_INT_NI | \ SDMMC_IDMAC_INT_CES | SDMMC_IDMAC_INT_DU | \ SDMMC_IDMAC_INT_FBE | SDMMC_IDMAC_INT_RI | \ @@ -102,7 +101,6 @@ struct idmac_desc { /* Each descriptor can transfer up to 4KB of data in chained mode */ #define DW_MCI_DESC_DATA_LENGTH 0x1000 -#endif /* CONFIG_MMC_DW_IDMAC */ static bool dw_mci_reset(struct dw_mci *host); static bool dw_mci_ctrl_reset(struct dw_mci *host, u32 reset); @@ -407,7 +405,6 @@ static int dw_mci_get_dma_dir(struct mmc_data *data) return DMA_FROM_DEVICE; } -#ifdef CONFIG_MMC_DW_IDMAC static void dw_mci_dma_cleanup(struct dw_mci *host) { struct mmc_data *data = host->data; @@ -445,12 +442,21 @@ static void dw_mci_idmac_stop_dma(struct dw_mci *host) mci_writel(host, BMOD, temp); } -static void dw_mci_idmac_complete_dma(struct dw_mci *host) +static void dw_mci_dmac_complete_dma(void *arg) { + struct dw_mci *host = arg; struct mmc_data *data = host->data; dev_vdbg(host->dev, "DMA complete\n"); + if ((host->use_dma == TRANS_MODE_EDMAC) && + data && (data->flags & MMC_DATA_READ)) + /* Invalidate cache after read */ + dma_sync_sg_for_cpu(mmc_dev(host->cur_slot->mmc), + data->sg, + data->sg_len, + DMA_FROM_DEVICE); + host->dma_ops->cleanup(host); /* @@ -564,7 +570,7 @@ static void dw_mci_translate_sglist(struct dw_mci *host, struct mmc_data *data, wmb(); /* drain writebuffer */ } -static void dw_mci_idmac_start_dma(struct dw_mci *host, unsigned int sg_len) +static int dw_mci_idmac_start_dma(struct dw_mci *host, unsigned int sg_len) { u32 temp; @@ -589,6 +595,8 @@ static void dw_mci_idmac_start_dma(struct dw_mci *host, unsigned int sg_len) /* Start it running */ mci_writel(host, PLDMND, 1); + + return 0; } static int dw_mci_idmac_init(struct dw_mci *host) @@ -669,10 +677,110 @@ static const struct dw_mci_dma_ops dw_mci_idmac_ops = { .init = dw_mci_idmac_init, .start = dw_mci_idmac_start_dma, .stop = dw_mci_idmac_stop_dma, - .complete = dw_mci_idmac_complete_dma, + .complete = dw_mci_dmac_complete_dma, + .cleanup = dw_mci_dma_cleanup, +}; + +static void dw_mci_edmac_stop_dma(struct dw_mci *host) +{ + dmaengine_terminate_all(host->dms->ch); +} + +static int dw_mci_edmac_start_dma(struct dw_mci *host, + unsigned int sg_len) +{ + struct dma_slave_config cfg; + struct dma_async_tx_descriptor *desc = NULL; + struct scatterlist *sgl = host->data->sg; + const u32 mszs[] = {1, 4, 8, 16, 32, 64, 128, 256}; + u32 sg_elems = host->data->sg_len; + u32 fifoth_val; + u32 fifo_offset = host->fifo_reg - host->regs; + int ret = 0; + + /* Set external dma config: burst size, burst width */ + cfg.dst_addr = (dma_addr_t)(host->phy_regs + fifo_offset); + cfg.src_addr = cfg.dst_addr; + cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; + cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; + + /* Match burst msize with external dma config */ + fifoth_val = mci_readl(host, FIFOTH); + cfg.dst_maxburst = mszs[(fifoth_val >> 28) & 0x7]; + cfg.src_maxburst = cfg.dst_maxburst; + + if (host->data->flags & MMC_DATA_WRITE) + cfg.direction = DMA_MEM_TO_DEV; + else + cfg.direction = DMA_DEV_TO_MEM; + + ret = dmaengine_slave_config(host->dms->ch, &cfg); + if (ret) { + dev_err(host->dev, "Failed to config edmac.\n"); + return -EBUSY; + } + + desc = dmaengine_prep_slave_sg(host->dms->ch, sgl, + sg_len, cfg.direction, + DMA_PREP_INTERRUPT | DMA_CTRL_ACK); + if (!desc) { + dev_err(host->dev, "Can't prepare slave sg.\n"); + return -EBUSY; + } + + /* Set dw_mci_dmac_complete_dma as callback */ + desc->callback = dw_mci_dmac_complete_dma; + desc->callback_param = (void *)host; + dmaengine_submit(desc); + + /* Flush cache before write */ + if (host->data->flags & MMC_DATA_WRITE) + dma_sync_sg_for_device(mmc_dev(host->cur_slot->mmc), sgl, + sg_elems, DMA_TO_DEVICE); + + dma_async_issue_pending(host->dms->ch); + + return 0; +} + +static int dw_mci_edmac_init(struct dw_mci *host) +{ + /* Request external dma channel */ + host->dms = kzalloc(sizeof(struct dw_mci_dma_slave), GFP_KERNEL); + if (!host->dms) + return -ENOMEM; + + host->dms->ch = dma_request_slave_channel(host->dev, "rx-tx"); + if (!host->dms->ch) { + dev_err(host->dev, "Failed to get external DMA channel.\n"); + kfree(host->dms); + host->dms = NULL; + return -ENXIO; + } + + return 0; +} + +static void dw_mci_edmac_exit(struct dw_mci *host) +{ + if (host->dms) { + if (host->dms->ch) { + dma_release_channel(host->dms->ch); + host->dms->ch = NULL; + } + kfree(host->dms); + host->dms = NULL; + } +} + +static const struct dw_mci_dma_ops dw_mci_edmac_ops = { + .init = dw_mci_edmac_init, + .exit = dw_mci_edmac_exit, + .start = dw_mci_edmac_start_dma, + .stop = dw_mci_edmac_stop_dma, + .complete = dw_mci_dmac_complete_dma, .cleanup = dw_mci_dma_cleanup, }; -#endif /* CONFIG_MMC_DW_IDMAC */ static int dw_mci_pre_dma_transfer(struct dw_mci *host, struct mmc_data *data, @@ -752,7 +860,6 @@ static void dw_mci_post_req(struct mmc_host *mmc, static void dw_mci_adjust_fifoth(struct dw_mci *host, struct mmc_data *data) { -#ifdef CONFIG_MMC_DW_IDMAC unsigned int blksz = data->blksz; const u32 mszs[] = {1, 4, 8, 16, 32, 64, 128, 256}; u32 fifo_width = 1 << host->data_shift; @@ -760,6 +867,10 @@ static void dw_mci_adjust_fifoth(struct dw_mci *host, struct mmc_data *data) u32 msize = 0, rx_wmark = 1, tx_wmark, tx_wmark_invers; int idx = ARRAY_SIZE(mszs) - 1; + /* pio should ship this scenario */ + if (!host->use_dma) + return; + tx_wmark = (host->fifo_depth) / 2; tx_wmark_invers = host->fifo_depth - tx_wmark; @@ -788,7 +899,6 @@ static void dw_mci_adjust_fifoth(struct dw_mci *host, struct mmc_data *data) done: fifoth_val = SDMMC_SET_FIFOTH(msize, rx_wmark, tx_wmark); mci_writel(host, FIFOTH, fifoth_val); -#endif } static void dw_mci_ctrl_rd_thld(struct dw_mci *host, struct mmc_data *data) @@ -850,10 +960,12 @@ static int dw_mci_submit_data_dma(struct dw_mci *host, struct mmc_data *data) host->using_dma = 1; - dev_vdbg(host->dev, - "sd sg_cpu: %#lx sg_dma: %#lx sg_len: %d\n", - (unsigned long)host->sg_cpu, (unsigned long)host->sg_dma, - sg_len); + if (host->use_dma == TRANS_MODE_IDMAC) + dev_vdbg(host->dev, + "sd sg_cpu: %#lx sg_dma: %#lx sg_len: %d\n", + (unsigned long)host->sg_cpu, + (unsigned long)host->sg_dma, + sg_len); /* * Decide the MSIZE and RX/TX Watermark. @@ -875,7 +987,11 @@ static int dw_mci_submit_data_dma(struct dw_mci *host, struct mmc_data *data) mci_writel(host, INTMASK, temp); spin_unlock_irqrestore(&host->irq_lock, irqflags); - host->dma_ops->start(host, sg_len); + if (host->dma_ops->start(host, sg_len)) { + /* We can't do DMA */ + dev_err(host->dev, "%s: failed to start DMA.\n", __func__); + return -ENODEV; + } return 0; } @@ -1177,6 +1293,7 @@ static void dw_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) /* DDR mode set */ if (ios->timing == MMC_TIMING_MMC_DDR52 || + ios->timing == MMC_TIMING_UHS_DDR50 || ios->timing == MMC_TIMING_MMC_HS400) regs |= ((0x1 << slot->id) << 16); else @@ -1279,7 +1396,6 @@ static int dw_mci_switch_voltage(struct mmc_host *mmc, struct mmc_ios *ios) const struct dw_mci_drv_data *drv_data = host->drv_data; u32 uhs; u32 v18 = SDMMC_UHS_18V << slot->id; - int min_uv, max_uv; int ret; if (drv_data && drv_data->switch_voltage) @@ -1291,22 +1407,18 @@ static int dw_mci_switch_voltage(struct mmc_host *mmc, struct mmc_ios *ios) * does no harm but you need to set the regulator directly. Try both. */ uhs = mci_readl(host, UHS_REG); - if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_330) { - min_uv = 2700000; - max_uv = 3600000; + if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_330) uhs &= ~v18; - } else { - min_uv = 1700000; - max_uv = 1950000; + else uhs |= v18; - } + if (!IS_ERR(mmc->supply.vqmmc)) { - ret = regulator_set_voltage(mmc->supply.vqmmc, min_uv, max_uv); + ret = mmc_regulator_set_vqmmc(mmc, ios); if (ret) { dev_dbg(&mmc->class_dev, - "Regulator set error %d: %d - %d\n", - ret, min_uv, max_uv); + "Regulator set error %d - %s V\n", + ret, uhs & v18 ? "1.8" : "3.3"); return ret; } } @@ -1427,7 +1539,7 @@ static int dw_mci_execute_tuning(struct mmc_host *mmc, u32 opcode) int err = -EINVAL; if (drv_data && drv_data->execute_tuning) - err = drv_data->execute_tuning(slot); + err = drv_data->execute_tuning(slot, opcode); return err; } @@ -2343,15 +2455,17 @@ static irqreturn_t dw_mci_interrupt(int irq, void *dev_id) } -#ifdef CONFIG_MMC_DW_IDMAC - /* Handle DMA interrupts */ + if (host->use_dma != TRANS_MODE_IDMAC) + return IRQ_HANDLED; + + /* Handle IDMA interrupts */ if (host->dma_64bit_address == 1) { pending = mci_readl(host, IDSTS64); if (pending & (SDMMC_IDMAC_INT_TI | SDMMC_IDMAC_INT_RI)) { mci_writel(host, IDSTS64, SDMMC_IDMAC_INT_TI | SDMMC_IDMAC_INT_RI); mci_writel(host, IDSTS64, SDMMC_IDMAC_INT_NI); - host->dma_ops->complete(host); + host->dma_ops->complete((void *)host); } } else { pending = mci_readl(host, IDSTS); @@ -2359,10 +2473,9 @@ static irqreturn_t dw_mci_interrupt(int irq, void *dev_id) mci_writel(host, IDSTS, SDMMC_IDMAC_INT_TI | SDMMC_IDMAC_INT_RI); mci_writel(host, IDSTS, SDMMC_IDMAC_INT_NI); - host->dma_ops->complete(host); + host->dma_ops->complete((void *)host); } } -#endif return IRQ_HANDLED; } @@ -2471,13 +2584,21 @@ static int dw_mci_init_slot(struct dw_mci *host, unsigned int id) goto err_host_allocated; /* Useful defaults if platform data is unset. */ - if (host->use_dma) { + if (host->use_dma == TRANS_MODE_IDMAC) { mmc->max_segs = host->ring_size; mmc->max_blk_size = 65536; mmc->max_seg_size = 0x1000; mmc->max_req_size = mmc->max_seg_size * host->ring_size; mmc->max_blk_count = mmc->max_req_size / 512; + } else if (host->use_dma == TRANS_MODE_EDMAC) { + mmc->max_segs = 64; + mmc->max_blk_size = 65536; + mmc->max_blk_count = 65535; + mmc->max_req_size = + mmc->max_blk_size * mmc->max_blk_count; + mmc->max_seg_size = mmc->max_req_size; } else { + /* TRANS_MODE_PIO */ mmc->max_segs = 64; mmc->max_blk_size = 65536; /* BLKSIZ is 16 bits */ mmc->max_blk_count = 512; @@ -2517,38 +2638,74 @@ static void dw_mci_cleanup_slot(struct dw_mci_slot *slot, unsigned int id) static void dw_mci_init_dma(struct dw_mci *host) { int addr_config; - /* Check ADDR_CONFIG bit in HCON to find IDMAC address bus width */ - addr_config = (mci_readl(host, HCON) >> 27) & 0x01; - - if (addr_config == 1) { - /* host supports IDMAC in 64-bit address mode */ - host->dma_64bit_address = 1; - dev_info(host->dev, "IDMAC supports 64-bit address mode.\n"); - if (!dma_set_mask(host->dev, DMA_BIT_MASK(64))) - dma_set_coherent_mask(host->dev, DMA_BIT_MASK(64)); - } else { - /* host supports IDMAC in 32-bit address mode */ - host->dma_64bit_address = 0; - dev_info(host->dev, "IDMAC supports 32-bit address mode.\n"); - } + struct device *dev = host->dev; + struct device_node *np = dev->of_node; - /* Alloc memory for sg translation */ - host->sg_cpu = dmam_alloc_coherent(host->dev, PAGE_SIZE, - &host->sg_dma, GFP_KERNEL); - if (!host->sg_cpu) { - dev_err(host->dev, "%s: could not alloc DMA memory\n", - __func__); + /* + * Check tansfer mode from HCON[17:16] + * Clear the ambiguous description of dw_mmc databook: + * 2b'00: No DMA Interface -> Actually means using Internal DMA block + * 2b'01: DesignWare DMA Interface -> Synopsys DW-DMA block + * 2b'10: Generic DMA Interface -> non-Synopsys generic DMA block + * 2b'11: Non DW DMA Interface -> pio only + * Compared to DesignWare DMA Interface, Generic DMA Interface has a + * simpler request/acknowledge handshake mechanism and both of them + * are regarded as external dma master for dw_mmc. + */ + host->use_dma = SDMMC_GET_TRANS_MODE(mci_readl(host, HCON)); + if (host->use_dma == DMA_INTERFACE_IDMA) { + host->use_dma = TRANS_MODE_IDMAC; + } else if (host->use_dma == DMA_INTERFACE_DWDMA || + host->use_dma == DMA_INTERFACE_GDMA) { + host->use_dma = TRANS_MODE_EDMAC; + } else { goto no_dma; } /* Determine which DMA interface to use */ -#ifdef CONFIG_MMC_DW_IDMAC - host->dma_ops = &dw_mci_idmac_ops; - dev_info(host->dev, "Using internal DMA controller.\n"); -#endif + if (host->use_dma == TRANS_MODE_IDMAC) { + /* + * Check ADDR_CONFIG bit in HCON to find + * IDMAC address bus width + */ + addr_config = SDMMC_GET_ADDR_CONFIG(mci_readl(host, HCON)); + + if (addr_config == 1) { + /* host supports IDMAC in 64-bit address mode */ + host->dma_64bit_address = 1; + dev_info(host->dev, + "IDMAC supports 64-bit address mode.\n"); + if (!dma_set_mask(host->dev, DMA_BIT_MASK(64))) + dma_set_coherent_mask(host->dev, + DMA_BIT_MASK(64)); + } else { + /* host supports IDMAC in 32-bit address mode */ + host->dma_64bit_address = 0; + dev_info(host->dev, + "IDMAC supports 32-bit address mode.\n"); + } - if (!host->dma_ops) - goto no_dma; + /* Alloc memory for sg translation */ + host->sg_cpu = dmam_alloc_coherent(host->dev, PAGE_SIZE, + &host->sg_dma, GFP_KERNEL); + if (!host->sg_cpu) { + dev_err(host->dev, + "%s: could not alloc DMA memory\n", + __func__); + goto no_dma; + } + + host->dma_ops = &dw_mci_idmac_ops; + dev_info(host->dev, "Using internal DMA controller.\n"); + } else { + /* TRANS_MODE_EDMAC: check dma bindings again */ + if ((of_property_count_strings(np, "dma-names") < 0) || + (!of_find_property(np, "dmas", NULL))) { + goto no_dma; + } + host->dma_ops = &dw_mci_edmac_ops; + dev_info(host->dev, "Using external DMA controller.\n"); + } if (host->dma_ops->init && host->dma_ops->start && host->dma_ops->stop && host->dma_ops->cleanup) { @@ -2562,12 +2719,11 @@ static void dw_mci_init_dma(struct dw_mci *host) goto no_dma; } - host->use_dma = 1; return; no_dma: dev_info(host->dev, "Using PIO mode.\n"); - host->use_dma = 0; + host->use_dma = TRANS_MODE_PIO; } static bool dw_mci_ctrl_reset(struct dw_mci *host, u32 reset) @@ -2650,10 +2806,9 @@ static bool dw_mci_reset(struct dw_mci *host) } } -#if IS_ENABLED(CONFIG_MMC_DW_IDMAC) - /* It is also recommended that we reset and reprogram idmac */ - dw_mci_idmac_reset(host); -#endif + if (host->use_dma == TRANS_MODE_IDMAC) + /* It is also recommended that we reset and reprogram idmac */ + dw_mci_idmac_reset(host); ret = true; @@ -2890,7 +3045,7 @@ int dw_mci_probe(struct dw_mci *host) * Get the host data width - this assumes that HCON has been set with * the correct values. */ - i = (mci_readl(host, HCON) >> 7) & 0x7; + i = SDMMC_GET_HDATA_WIDTH(mci_readl(host, HCON)); if (!i) { host->push_data = dw_mci_push_data16; host->pull_data = dw_mci_pull_data16; @@ -2972,7 +3127,7 @@ int dw_mci_probe(struct dw_mci *host) if (host->pdata->num_slots) host->num_slots = host->pdata->num_slots; else - host->num_slots = ((mci_readl(host, HCON) >> 1) & 0x1F) + 1; + host->num_slots = SDMMC_GET_SLOT_NUM(mci_readl(host, HCON)); /* * Enable interrupts for command done, data over, data empty, @@ -3067,6 +3222,9 @@ EXPORT_SYMBOL(dw_mci_remove); */ int dw_mci_suspend(struct dw_mci *host) { + if (host->use_dma && host->dma_ops->exit) + host->dma_ops->exit(host); + return 0; } EXPORT_SYMBOL(dw_mci_suspend); diff --git a/drivers/mmc/host/dw_mmc.h b/drivers/mmc/host/dw_mmc.h index 8ce4674730a6..f695b58f0613 100644 --- a/drivers/mmc/host/dw_mmc.h +++ b/drivers/mmc/host/dw_mmc.h @@ -148,6 +148,15 @@ #define SDMMC_SET_FIFOTH(m, r, t) (((m) & 0x7) << 28 | \ ((r) & 0xFFF) << 16 | \ ((t) & 0xFFF)) +/* HCON register defines */ +#define DMA_INTERFACE_IDMA (0x0) +#define DMA_INTERFACE_DWDMA (0x1) +#define DMA_INTERFACE_GDMA (0x2) +#define DMA_INTERFACE_NODMA (0x3) +#define SDMMC_GET_TRANS_MODE(x) (((x)>>16) & 0x3) +#define SDMMC_GET_SLOT_NUM(x) ((((x)>>1) & 0x1F) + 1) +#define SDMMC_GET_HDATA_WIDTH(x) (((x)>>7) & 0x7) +#define SDMMC_GET_ADDR_CONFIG(x) (((x)>>27) & 0x1) /* Internal DMAC interrupt defines */ #define SDMMC_IDMAC_INT_AI BIT(9) #define SDMMC_IDMAC_INT_NI BIT(8) @@ -163,7 +172,7 @@ /* Version ID register define */ #define SDMMC_GET_VERID(x) ((x) & 0xFFFF) /* Card read threshold */ -#define SDMMC_SET_RD_THLD(v, x) (((v) & 0x1FFF) << 16 | (x)) +#define SDMMC_SET_RD_THLD(v, x) (((v) & 0xFFF) << 16 | (x)) #define SDMMC_UHS_18V BIT(0) /* All ctrl reset bits */ #define SDMMC_CTRL_ALL_RESET_FLAGS \ @@ -281,7 +290,7 @@ struct dw_mci_drv_data { void (*prepare_command)(struct dw_mci *host, u32 *cmdr); void (*set_ios)(struct dw_mci *host, struct mmc_ios *ios); int (*parse_dt)(struct dw_mci *host); - int (*execute_tuning)(struct dw_mci_slot *slot); + int (*execute_tuning)(struct dw_mci_slot *slot, u32 opcode); int (*prepare_hs400_tuning)(struct dw_mci *host, struct mmc_ios *ios); int (*switch_voltage)(struct mmc_host *mmc, diff --git a/drivers/mmc/host/mmc_spi.c b/drivers/mmc/host/mmc_spi.c index ae19d83bb9de..8ee11f4120fc 100644 --- a/drivers/mmc/host/mmc_spi.c +++ b/drivers/mmc/host/mmc_spi.c @@ -1511,6 +1511,7 @@ static const struct of_device_id mmc_spi_of_match_table[] = { { .compatible = "mmc-spi-slot", }, {}, }; +MODULE_DEVICE_TABLE(of, mmc_spi_of_match_table); static struct spi_driver mmc_spi_driver = { .driver = { diff --git a/drivers/mmc/host/moxart-mmc.c b/drivers/mmc/host/moxart-mmc.c index 006f1862444b..79905ce895ad 100644 --- a/drivers/mmc/host/moxart-mmc.c +++ b/drivers/mmc/host/moxart-mmc.c @@ -711,6 +711,7 @@ static const struct of_device_id moxart_mmc_match[] = { { .compatible = "faraday,ftsdc010" }, { } }; +MODULE_DEVICE_TABLE(of, moxart_mmc_match); static struct platform_driver moxart_mmc_driver = { .probe = moxart_probe, diff --git a/drivers/mmc/host/mtk-sd.c b/drivers/mmc/host/mtk-sd.c index 7153500dd007..39568cc29a2a 100644 --- a/drivers/mmc/host/mtk-sd.c +++ b/drivers/mmc/host/mtk-sd.c @@ -26,6 +26,7 @@ #include <linux/pm.h> #include <linux/pm_runtime.h> #include <linux/regulator/consumer.h> +#include <linux/slab.h> #include <linux/spinlock.h> #include <linux/mmc/card.h> @@ -64,6 +65,7 @@ #define SDC_RESP2 0x48 #define SDC_RESP3 0x4c #define SDC_BLK_NUM 0x50 +#define EMMC_IOCON 0x7c #define SDC_ACMD_RESP 0x80 #define MSDC_DMA_SA 0x90 #define MSDC_DMA_CTRL 0x98 @@ -71,6 +73,8 @@ #define MSDC_PATCH_BIT 0xb0 #define MSDC_PATCH_BIT1 0xb4 #define MSDC_PAD_TUNE 0xec +#define PAD_DS_TUNE 0x188 +#define EMMC50_CFG0 0x208 /*--------------------------------------------------------------------------*/ /* Register Mask */ @@ -87,6 +91,7 @@ #define MSDC_CFG_CKSTB (0x1 << 7) /* R */ #define MSDC_CFG_CKDIV (0xff << 8) /* RW */ #define MSDC_CFG_CKMOD (0x3 << 16) /* RW */ +#define MSDC_CFG_HS400_CK_MODE (0x1 << 18) /* RW */ /* MSDC_IOCON mask */ #define MSDC_IOCON_SDR104CKS (0x1 << 0) /* RW */ @@ -204,6 +209,17 @@ #define MSDC_PATCH_BIT_SPCPUSH (0x1 << 29) /* RW */ #define MSDC_PATCH_BIT_DECRCTMO (0x1 << 30) /* RW */ +#define MSDC_PAD_TUNE_DATRRDLY (0x1f << 8) /* RW */ +#define MSDC_PAD_TUNE_CMDRDLY (0x1f << 16) /* RW */ + +#define PAD_DS_TUNE_DLY1 (0x1f << 2) /* RW */ +#define PAD_DS_TUNE_DLY2 (0x1f << 7) /* RW */ +#define PAD_DS_TUNE_DLY3 (0x1f << 12) /* RW */ + +#define EMMC50_CFG_PADCMD_LATCHCK (0x1 << 0) /* RW */ +#define EMMC50_CFG_CRCSTS_EDGE (0x1 << 3) /* RW */ +#define EMMC50_CFG_CFCSTS_SEL (0x1 << 4) /* RW */ + #define REQ_CMD_EIO (0x1 << 0) #define REQ_CMD_TMO (0x1 << 1) #define REQ_DAT_ERR (0x1 << 2) @@ -219,6 +235,7 @@ #define CMD_TIMEOUT (HZ/10 * 5) /* 100ms x5 */ #define DAT_TIMEOUT (HZ * 5) /* 1000ms x5 */ +#define PAD_DELAY_MAX 32 /* PAD delay cells */ /*--------------------------------------------------------------------------*/ /* Descriptor Structure */ /*--------------------------------------------------------------------------*/ @@ -265,6 +282,14 @@ struct msdc_save_para { u32 pad_tune; u32 patch_bit0; u32 patch_bit1; + u32 pad_ds_tune; + u32 emmc50_cfg0; +}; + +struct msdc_delay_phase { + u8 maxlen; + u8 start; + u8 final_phase; }; struct msdc_host { @@ -297,8 +322,9 @@ struct msdc_host { u32 mclk; /* mmc subsystem clock frequency */ u32 src_clk_freq; /* source clock frequency */ u32 sclk; /* SD/MS bus clock frequency */ - bool ddr; + unsigned char timing; bool vqmmc_enabled; + u32 hs400_ds_delay; struct msdc_save_para save_para; /* used when gate HCLK */ }; @@ -353,7 +379,10 @@ static void msdc_reset_hw(struct msdc_host *host) static void msdc_cmd_next(struct msdc_host *host, struct mmc_request *mrq, struct mmc_command *cmd); -static u32 data_ints_mask = MSDC_INTEN_XFER_COMPL | MSDC_INTEN_DATTMO | +static const u32 cmd_ints_mask = MSDC_INTEN_CMDRDY | MSDC_INTEN_RSPCRCERR | + MSDC_INTEN_CMDTMO | MSDC_INTEN_ACMDRDY | + MSDC_INTEN_ACMDCRCERR | MSDC_INTEN_ACMDTMO; +static const u32 data_ints_mask = MSDC_INTEN_XFER_COMPL | MSDC_INTEN_DATTMO | MSDC_INTEN_DATCRCERR | MSDC_INTEN_DMA_BDCSERR | MSDC_INTEN_DMA_GPDCSERR | MSDC_INTEN_DMA_PROTECT; @@ -485,7 +514,7 @@ static void msdc_ungate_clock(struct msdc_host *host) cpu_relax(); } -static void msdc_set_mclk(struct msdc_host *host, int ddr, u32 hz) +static void msdc_set_mclk(struct msdc_host *host, unsigned char timing, u32 hz) { u32 mode; u32 flags; @@ -501,8 +530,15 @@ static void msdc_set_mclk(struct msdc_host *host, int ddr, u32 hz) flags = readl(host->base + MSDC_INTEN); sdr_clr_bits(host->base + MSDC_INTEN, flags); - if (ddr) { /* may need to modify later */ - mode = 0x2; /* ddr mode and use divisor */ + sdr_clr_bits(host->base + MSDC_CFG, MSDC_CFG_HS400_CK_MODE); + if (timing == MMC_TIMING_UHS_DDR50 || + timing == MMC_TIMING_MMC_DDR52 || + timing == MMC_TIMING_MMC_HS400) { + if (timing == MMC_TIMING_MMC_HS400) + mode = 0x3; + else + mode = 0x2; /* ddr mode and use divisor */ + if (hz >= (host->src_clk_freq >> 2)) { div = 0; /* mean div = 1/4 */ sclk = host->src_clk_freq >> 2; /* sclk = clk / 4 */ @@ -511,6 +547,14 @@ static void msdc_set_mclk(struct msdc_host *host, int ddr, u32 hz) sclk = (host->src_clk_freq >> 2) / div; div = (div >> 1); } + + if (timing == MMC_TIMING_MMC_HS400 && + hz >= (host->src_clk_freq >> 1)) { + sdr_set_bits(host->base + MSDC_CFG, + MSDC_CFG_HS400_CK_MODE); + sclk = host->src_clk_freq >> 1; + div = 0; /* div is ignore when bit18 is set */ + } } else if (hz >= host->src_clk_freq) { mode = 0x1; /* no divisor */ div = 0; @@ -532,12 +576,12 @@ static void msdc_set_mclk(struct msdc_host *host, int ddr, u32 hz) cpu_relax(); host->sclk = sclk; host->mclk = hz; - host->ddr = ddr; + host->timing = timing; /* need because clk changed. */ msdc_set_timeout(host, host->timeout_ns, host->timeout_clks); sdr_set_bits(host->base + MSDC_INTEN, flags); - dev_dbg(host->dev, "sclk: %d, ddr: %d\n", host->sclk, ddr); + dev_dbg(host->dev, "sclk: %d, timing: %d\n", host->sclk, timing); } static inline u32 msdc_cmd_find_resp(struct msdc_host *host, @@ -725,11 +769,7 @@ static bool msdc_cmd_done(struct msdc_host *host, int events, if (done) return true; - sdr_clr_bits(host->base + MSDC_INTEN, MSDC_INTEN_CMDRDY | - MSDC_INTEN_RSPCRCERR | MSDC_INTEN_CMDTMO | - MSDC_INTEN_ACMDRDY | MSDC_INTEN_ACMDCRCERR | - MSDC_INTEN_ACMDTMO); - writel(cmd->arg, host->base + SDC_ARG); + sdr_clr_bits(host->base + MSDC_INTEN, cmd_ints_mask); if (cmd->flags & MMC_RSP_PRESENT) { if (cmd->flags & MMC_RSP_136) { @@ -819,10 +859,7 @@ static void msdc_start_command(struct msdc_host *host, rawcmd = msdc_cmd_prepare_raw_cmd(host, mrq, cmd); mod_delayed_work(system_wq, &host->req_timeout, DAT_TIMEOUT); - sdr_set_bits(host->base + MSDC_INTEN, MSDC_INTEN_CMDRDY | - MSDC_INTEN_RSPCRCERR | MSDC_INTEN_CMDTMO | - MSDC_INTEN_ACMDRDY | MSDC_INTEN_ACMDCRCERR | - MSDC_INTEN_ACMDTMO); + sdr_set_bits(host->base + MSDC_INTEN, cmd_ints_mask); writel(cmd->arg, host->base + SDC_ARG); writel(rawcmd, host->base + SDC_CMD); } @@ -896,7 +933,7 @@ static void msdc_data_xfer_next(struct msdc_host *host, struct mmc_request *mrq, struct mmc_data *data) { if (mmc_op_multi(mrq->cmd->opcode) && mrq->stop && !mrq->stop->error && - (!data->bytes_xfered || !mrq->sbc)) + !mrq->sbc) msdc_start_command(host, mrq, mrq->stop); else msdc_request_done(host, mrq); @@ -942,6 +979,8 @@ static bool msdc_data_xfer_done(struct msdc_host *host, u32 events, if (events & MSDC_INT_DATTMO) data->error = -ETIMEDOUT; + else if (events & MSDC_INT_DATCRCERR) + data->error = -EILSEQ; dev_err(host->dev, "%s: cmd=%d; blocks=%d", __func__, mrq->cmd->opcode, data->blocks); @@ -1113,10 +1152,12 @@ static void msdc_init_hw(struct msdc_host *host) writel(0, host->base + MSDC_PAD_TUNE); writel(0, host->base + MSDC_IOCON); - sdr_set_field(host->base + MSDC_IOCON, MSDC_IOCON_DDLSEL, 1); - writel(0x403c004f, host->base + MSDC_PATCH_BIT); + sdr_set_field(host->base + MSDC_IOCON, MSDC_IOCON_DDLSEL, 0); + writel(0x403c0046, host->base + MSDC_PATCH_BIT); sdr_set_field(host->base + MSDC_PATCH_BIT, MSDC_CKGEN_MSDC_DLY_SEL, 1); writel(0xffff0089, host->base + MSDC_PATCH_BIT1); + sdr_set_bits(host->base + EMMC50_CFG0, EMMC50_CFG_CFCSTS_SEL); + /* Configure to enable SDIO mode. * it's must otherwise sdio cmd5 failed */ @@ -1148,11 +1189,14 @@ static void msdc_init_gpd_bd(struct msdc_host *host, struct msdc_dma *dma) struct mt_bdma_desc *bd = dma->bd; int i; - memset(gpd, 0, sizeof(struct mt_gpdma_desc)); + memset(gpd, 0, sizeof(struct mt_gpdma_desc) * 2); gpd->gpd_info = GPDMA_DESC_BDP; /* hwo, cs, bd pointer */ gpd->ptr = (u32)dma->bd_addr; /* physical address */ - + /* gpd->next is must set for desc DMA + * That's why must alloc 2 gpd structure. + */ + gpd->next = (u32)dma->gpd_addr + sizeof(struct mt_gpdma_desc); memset(bd, 0, sizeof(struct mt_bdma_desc) * MAX_BD_NUM); for (i = 0; i < (MAX_BD_NUM - 1); i++) bd[i].next = (u32)dma->bd_addr + sizeof(*bd) * (i + 1); @@ -1162,20 +1206,16 @@ static void msdc_ops_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) { struct msdc_host *host = mmc_priv(mmc); int ret; - u32 ddr = 0; pm_runtime_get_sync(host->dev); - if (ios->timing == MMC_TIMING_UHS_DDR50 || - ios->timing == MMC_TIMING_MMC_DDR52) - ddr = 1; - msdc_set_buswidth(host, ios->bus_width); /* Suspend/Resume will do power off/on */ switch (ios->power_mode) { case MMC_POWER_UP: if (!IS_ERR(mmc->supply.vmmc)) { + msdc_init_hw(host); ret = mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, ios->vdd); if (ret) { @@ -1206,14 +1246,207 @@ static void msdc_ops_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) break; } - if (host->mclk != ios->clock || host->ddr != ddr) - msdc_set_mclk(host, ddr, ios->clock); + if (host->mclk != ios->clock || host->timing != ios->timing) + msdc_set_mclk(host, ios->timing, ios->clock); end: pm_runtime_mark_last_busy(host->dev); pm_runtime_put_autosuspend(host->dev); } +static u32 test_delay_bit(u32 delay, u32 bit) +{ + bit %= PAD_DELAY_MAX; + return delay & (1 << bit); +} + +static int get_delay_len(u32 delay, u32 start_bit) +{ + int i; + + for (i = 0; i < (PAD_DELAY_MAX - start_bit); i++) { + if (test_delay_bit(delay, start_bit + i) == 0) + return i; + } + return PAD_DELAY_MAX - start_bit; +} + +static struct msdc_delay_phase get_best_delay(struct msdc_host *host, u32 delay) +{ + int start = 0, len = 0; + int start_final = 0, len_final = 0; + u8 final_phase = 0xff; + struct msdc_delay_phase delay_phase; + + if (delay == 0) { + dev_err(host->dev, "phase error: [map:%x]\n", delay); + delay_phase.final_phase = final_phase; + return delay_phase; + } + + while (start < PAD_DELAY_MAX) { + len = get_delay_len(delay, start); + if (len_final < len) { + start_final = start; + len_final = len; + } + start += len ? len : 1; + if (len >= 8 && start_final < 4) + break; + } + + /* The rule is that to find the smallest delay cell */ + if (start_final == 0) + final_phase = (start_final + len_final / 3) % PAD_DELAY_MAX; + else + final_phase = (start_final + len_final / 2) % PAD_DELAY_MAX; + dev_info(host->dev, "phase: [map:%x] [maxlen:%d] [final:%d]\n", + delay, len_final, final_phase); + + delay_phase.maxlen = len_final; + delay_phase.start = start_final; + delay_phase.final_phase = final_phase; + return delay_phase; +} + +static int msdc_tune_response(struct mmc_host *mmc, u32 opcode) +{ + struct msdc_host *host = mmc_priv(mmc); + u32 rise_delay = 0, fall_delay = 0; + struct msdc_delay_phase final_rise_delay, final_fall_delay; + u8 final_delay, final_maxlen; + int cmd_err; + int i; + + sdr_clr_bits(host->base + MSDC_IOCON, MSDC_IOCON_RSPL); + for (i = 0 ; i < PAD_DELAY_MAX; i++) { + sdr_set_field(host->base + MSDC_PAD_TUNE, + MSDC_PAD_TUNE_CMDRDLY, i); + mmc_send_tuning(mmc, opcode, &cmd_err); + if (!cmd_err) + rise_delay |= (1 << i); + } + + sdr_set_bits(host->base + MSDC_IOCON, MSDC_IOCON_RSPL); + for (i = 0; i < PAD_DELAY_MAX; i++) { + sdr_set_field(host->base + MSDC_PAD_TUNE, + MSDC_PAD_TUNE_CMDRDLY, i); + mmc_send_tuning(mmc, opcode, &cmd_err); + if (!cmd_err) + fall_delay |= (1 << i); + } + + final_rise_delay = get_best_delay(host, rise_delay); + final_fall_delay = get_best_delay(host, fall_delay); + + final_maxlen = max(final_rise_delay.maxlen, final_fall_delay.maxlen); + if (final_maxlen == final_rise_delay.maxlen) { + sdr_clr_bits(host->base + MSDC_IOCON, MSDC_IOCON_RSPL); + sdr_set_field(host->base + MSDC_PAD_TUNE, MSDC_PAD_TUNE_CMDRDLY, + final_rise_delay.final_phase); + final_delay = final_rise_delay.final_phase; + } else { + sdr_set_bits(host->base + MSDC_IOCON, MSDC_IOCON_RSPL); + sdr_set_field(host->base + MSDC_PAD_TUNE, MSDC_PAD_TUNE_CMDRDLY, + final_fall_delay.final_phase); + final_delay = final_fall_delay.final_phase; + } + + return final_delay == 0xff ? -EIO : 0; +} + +static int msdc_tune_data(struct mmc_host *mmc, u32 opcode) +{ + struct msdc_host *host = mmc_priv(mmc); + u32 rise_delay = 0, fall_delay = 0; + struct msdc_delay_phase final_rise_delay, final_fall_delay; + u8 final_delay, final_maxlen; + int i, ret; + + sdr_clr_bits(host->base + MSDC_IOCON, MSDC_IOCON_DSPL); + sdr_clr_bits(host->base + MSDC_IOCON, MSDC_IOCON_W_DSPL); + for (i = 0 ; i < PAD_DELAY_MAX; i++) { + sdr_set_field(host->base + MSDC_PAD_TUNE, + MSDC_PAD_TUNE_DATRRDLY, i); + ret = mmc_send_tuning(mmc, opcode, NULL); + if (!ret) + rise_delay |= (1 << i); + } + + sdr_set_bits(host->base + MSDC_IOCON, MSDC_IOCON_DSPL); + sdr_set_bits(host->base + MSDC_IOCON, MSDC_IOCON_W_DSPL); + for (i = 0; i < PAD_DELAY_MAX; i++) { + sdr_set_field(host->base + MSDC_PAD_TUNE, + MSDC_PAD_TUNE_DATRRDLY, i); + ret = mmc_send_tuning(mmc, opcode, NULL); + if (!ret) + fall_delay |= (1 << i); + } + + final_rise_delay = get_best_delay(host, rise_delay); + final_fall_delay = get_best_delay(host, fall_delay); + + final_maxlen = max(final_rise_delay.maxlen, final_fall_delay.maxlen); + /* Rising edge is more stable, prefer to use it */ + if (final_rise_delay.maxlen >= 10) + final_maxlen = final_rise_delay.maxlen; + if (final_maxlen == final_rise_delay.maxlen) { + sdr_clr_bits(host->base + MSDC_IOCON, MSDC_IOCON_DSPL); + sdr_clr_bits(host->base + MSDC_IOCON, MSDC_IOCON_W_DSPL); + sdr_set_field(host->base + MSDC_PAD_TUNE, + MSDC_PAD_TUNE_DATRRDLY, + final_rise_delay.final_phase); + final_delay = final_rise_delay.final_phase; + } else { + sdr_set_bits(host->base + MSDC_IOCON, MSDC_IOCON_DSPL); + sdr_set_bits(host->base + MSDC_IOCON, MSDC_IOCON_W_DSPL); + sdr_set_field(host->base + MSDC_PAD_TUNE, + MSDC_PAD_TUNE_DATRRDLY, + final_fall_delay.final_phase); + final_delay = final_fall_delay.final_phase; + } + + return final_delay == 0xff ? -EIO : 0; +} + +static int msdc_execute_tuning(struct mmc_host *mmc, u32 opcode) +{ + struct msdc_host *host = mmc_priv(mmc); + int ret; + + pm_runtime_get_sync(host->dev); + ret = msdc_tune_response(mmc, opcode); + if (ret == -EIO) { + dev_err(host->dev, "Tune response fail!\n"); + goto out; + } + ret = msdc_tune_data(mmc, opcode); + if (ret == -EIO) + dev_err(host->dev, "Tune data fail!\n"); + +out: + pm_runtime_mark_last_busy(host->dev); + pm_runtime_put_autosuspend(host->dev); + return ret; +} + +static int msdc_prepare_hs400_tuning(struct mmc_host *mmc, struct mmc_ios *ios) +{ + struct msdc_host *host = mmc_priv(mmc); + + writel(host->hs400_ds_delay, host->base + PAD_DS_TUNE); + return 0; +} + +static void msdc_hw_reset(struct mmc_host *mmc) +{ + struct msdc_host *host = mmc_priv(mmc); + + sdr_set_bits(host->base + EMMC_IOCON, 1); + udelay(10); /* 10us is enough */ + sdr_clr_bits(host->base + EMMC_IOCON, 1); +} + static struct mmc_host_ops mt_msdc_ops = { .post_req = msdc_post_req, .pre_req = msdc_pre_req, @@ -1221,6 +1454,9 @@ static struct mmc_host_ops mt_msdc_ops = { .set_ios = msdc_ops_set_ios, .start_signal_voltage_switch = msdc_ops_switch_volt, .card_busy = msdc_card_busy, + .execute_tuning = msdc_execute_tuning, + .prepare_hs400_tuning = msdc_prepare_hs400_tuning, + .hw_reset = msdc_hw_reset, }; static int msdc_drv_probe(struct platform_device *pdev) @@ -1294,6 +1530,11 @@ static int msdc_drv_probe(struct platform_device *pdev) goto host_free; } + if (!of_property_read_u32(pdev->dev.of_node, "hs400-ds-delay", + &host->hs400_ds_delay)) + dev_dbg(&pdev->dev, "hs400-ds-delay: %x\n", + host->hs400_ds_delay); + host->dev = &pdev->dev; host->mmc = mmc; host->src_clk_freq = clk_get_rate(host->src_clk); @@ -1302,6 +1543,7 @@ static int msdc_drv_probe(struct platform_device *pdev) mmc->f_min = host->src_clk_freq / (4 * 255); mmc->caps |= MMC_CAP_ERASE | MMC_CAP_CMD23; + mmc->caps |= MMC_CAP_RUNTIME_RESUME; /* MMC core transfer sizes tunable parameters */ mmc->max_segs = MAX_BD_NUM; mmc->max_seg_size = BDMA_DESC_BUFLEN; @@ -1313,7 +1555,7 @@ static int msdc_drv_probe(struct platform_device *pdev) host->timeout_clks = 3 * 1048576; host->dma.gpd = dma_alloc_coherent(&pdev->dev, - sizeof(struct mt_gpdma_desc), + 2 * sizeof(struct mt_gpdma_desc), &host->dma.gpd_addr, GFP_KERNEL); host->dma.bd = dma_alloc_coherent(&pdev->dev, MAX_BD_NUM * sizeof(struct mt_bdma_desc), @@ -1354,7 +1596,7 @@ release: release_mem: if (host->dma.gpd) dma_free_coherent(&pdev->dev, - sizeof(struct mt_gpdma_desc), + 2 * sizeof(struct mt_gpdma_desc), host->dma.gpd, host->dma.gpd_addr); if (host->dma.bd) dma_free_coherent(&pdev->dev, @@ -1403,6 +1645,8 @@ static void msdc_save_reg(struct msdc_host *host) host->save_para.pad_tune = readl(host->base + MSDC_PAD_TUNE); host->save_para.patch_bit0 = readl(host->base + MSDC_PATCH_BIT); host->save_para.patch_bit1 = readl(host->base + MSDC_PATCH_BIT1); + host->save_para.pad_ds_tune = readl(host->base + PAD_DS_TUNE); + host->save_para.emmc50_cfg0 = readl(host->base + EMMC50_CFG0); } static void msdc_restore_reg(struct msdc_host *host) @@ -1413,6 +1657,8 @@ static void msdc_restore_reg(struct msdc_host *host) writel(host->save_para.pad_tune, host->base + MSDC_PAD_TUNE); writel(host->save_para.patch_bit0, host->base + MSDC_PATCH_BIT); writel(host->save_para.patch_bit1, host->base + MSDC_PATCH_BIT1); + writel(host->save_para.pad_ds_tune, host->base + PAD_DS_TUNE); + writel(host->save_para.emmc50_cfg0, host->base + EMMC50_CFG0); } static int msdc_runtime_suspend(struct device *dev) diff --git a/drivers/mmc/host/omap.c b/drivers/mmc/host/omap.c index b763b11ed9e1..b9958a123594 100644 --- a/drivers/mmc/host/omap.c +++ b/drivers/mmc/host/omap.c @@ -1490,6 +1490,7 @@ static const struct of_device_id mmc_omap_match[] = { { .compatible = "ti,omap2420-mmc", }, { }, }; +MODULE_DEVICE_TABLE(of, mmc_omap_match); #endif static struct platform_driver mmc_omap_driver = { diff --git a/drivers/mmc/host/sdhci-acpi.c b/drivers/mmc/host/sdhci-acpi.c index 22d929fa3371..f6047fc94062 100644 --- a/drivers/mmc/host/sdhci-acpi.c +++ b/drivers/mmc/host/sdhci-acpi.c @@ -207,7 +207,9 @@ static const struct sdhci_acpi_slot sdhci_acpi_slot_int_emmc = { .caps2 = MMC_CAP2_HC_ERASE_SZ, .flags = SDHCI_ACPI_RUNTIME_PM, .quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC, - .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN | SDHCI_QUIRK2_STOP_WITH_TC, + .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN | + SDHCI_QUIRK2_STOP_WITH_TC | + SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400, .probe_slot = sdhci_acpi_emmc_probe_slot, }; @@ -239,6 +241,9 @@ struct sdhci_acpi_uid_slot { }; static const struct sdhci_acpi_uid_slot sdhci_acpi_uids[] = { + { "80865ACA", NULL, &sdhci_acpi_slot_int_sd }, + { "80865ACC", NULL, &sdhci_acpi_slot_int_emmc }, + { "80865AD0", NULL, &sdhci_acpi_slot_int_sdio }, { "80860F14" , "1" , &sdhci_acpi_slot_int_emmc }, { "80860F14" , "3" , &sdhci_acpi_slot_int_sd }, { "80860F16" , NULL, &sdhci_acpi_slot_int_sd }, @@ -247,11 +252,15 @@ static const struct sdhci_acpi_uid_slot sdhci_acpi_uids[] = { { "INT33C6" , NULL, &sdhci_acpi_slot_int_sdio }, { "INT3436" , NULL, &sdhci_acpi_slot_int_sdio }, { "INT344D" , NULL, &sdhci_acpi_slot_int_sdio }, + { "PNP0FFF" , "3" , &sdhci_acpi_slot_int_sd }, { "PNP0D40" }, { }, }; static const struct acpi_device_id sdhci_acpi_ids[] = { + { "80865ACA" }, + { "80865ACC" }, + { "80865AD0" }, { "80860F14" }, { "80860F16" }, { "INT33BB" }, diff --git a/drivers/mmc/host/sdhci-bcm-kona.c b/drivers/mmc/host/sdhci-bcm-kona.c index 2bd90fb35c75..00a8a40a3729 100644 --- a/drivers/mmc/host/sdhci-bcm-kona.c +++ b/drivers/mmc/host/sdhci-bcm-kona.c @@ -273,7 +273,7 @@ static int sdhci_bcm_kona_probe(struct platform_device *pdev) host->quirks |= SDHCI_QUIRK_BROKEN_CARD_DETECTION; dev_dbg(dev, "is_8bit=%c\n", - (host->mmc->caps | MMC_CAP_8_BIT_DATA) ? 'Y' : 'N'); + (host->mmc->caps & MMC_CAP_8_BIT_DATA) ? 'Y' : 'N'); ret = sdhci_bcm_kona_sd_reset(host); if (ret) diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c index 886d230f41d0..1f1582f6cccb 100644 --- a/drivers/mmc/host/sdhci-esdhc-imx.c +++ b/drivers/mmc/host/sdhci-esdhc-imx.c @@ -759,7 +759,7 @@ static int esdhc_executing_tuning(struct sdhci_host *host, u32 opcode) min = ESDHC_TUNE_CTRL_MIN; while (min < ESDHC_TUNE_CTRL_MAX) { esdhc_prepare_tuning(host, min); - if (!mmc_send_tuning(host->mmc)) + if (!mmc_send_tuning(host->mmc, opcode, NULL)) break; min += ESDHC_TUNE_CTRL_STEP; } @@ -768,7 +768,7 @@ static int esdhc_executing_tuning(struct sdhci_host *host, u32 opcode) max = min + ESDHC_TUNE_CTRL_STEP; while (max < ESDHC_TUNE_CTRL_MAX) { esdhc_prepare_tuning(host, max); - if (mmc_send_tuning(host->mmc)) { + if (mmc_send_tuning(host->mmc, opcode, NULL)) { max -= ESDHC_TUNE_CTRL_STEP; break; } @@ -778,7 +778,7 @@ static int esdhc_executing_tuning(struct sdhci_host *host, u32 opcode) /* use average delay to get the best timing */ avg = (min + max) / 2; esdhc_prepare_tuning(host, avg); - ret = mmc_send_tuning(host->mmc); + ret = mmc_send_tuning(host->mmc, opcode, NULL); esdhc_post_tuning(host); dev_dbg(mmc_dev(host->mmc), "tunning %s at 0x%x ret %d\n", diff --git a/drivers/mmc/host/sdhci-esdhc.h b/drivers/mmc/host/sdhci-esdhc.h index 163ac9974d91..de132e281753 100644 --- a/drivers/mmc/host/sdhci-esdhc.h +++ b/drivers/mmc/host/sdhci-esdhc.h @@ -24,6 +24,8 @@ SDHCI_QUIRK_PIO_NEEDS_DELAY | \ SDHCI_QUIRK_NO_HISPD_BIT) +#define ESDHC_PROCTL 0x28 + #define ESDHC_SYSTEM_CONTROL 0x2c #define ESDHC_CLOCK_MASK 0x0000fff0 #define ESDHC_PREDIV_SHIFT 8 diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c index 4bcee033feda..4695bee203ea 100644 --- a/drivers/mmc/host/sdhci-msm.c +++ b/drivers/mmc/host/sdhci-msm.c @@ -373,7 +373,7 @@ retry: if (rc) return rc; - rc = mmc_send_tuning(mmc); + rc = mmc_send_tuning(mmc, opcode, NULL); if (!rc) { /* Tuning is successful at this tuning point */ tuned_phases[tuned_phase_cnt++] = phase; diff --git a/drivers/mmc/host/sdhci-of-at91.c b/drivers/mmc/host/sdhci-of-at91.c index a0f05de5409f..06d0b50dfe71 100644 --- a/drivers/mmc/host/sdhci-of-at91.c +++ b/drivers/mmc/host/sdhci-of-at91.c @@ -111,7 +111,6 @@ static int sdhci_at91_probe(struct platform_device *pdev) if (ret < 0) { dev_err(&pdev->dev, "failed to set gck"); goto hclock_disable_unprepare; - return -EINVAL; } /* * We need to check if we have the requested rate for gck because in diff --git a/drivers/mmc/host/sdhci-of-esdhc.c b/drivers/mmc/host/sdhci-of-esdhc.c index 653f335bef15..90e94a028a49 100644 --- a/drivers/mmc/host/sdhci-of-esdhc.c +++ b/drivers/mmc/host/sdhci-of-esdhc.c @@ -24,122 +24,324 @@ #define VENDOR_V_22 0x12 #define VENDOR_V_23 0x13 -static u32 esdhc_readl(struct sdhci_host *host, int reg) + +struct sdhci_esdhc { + u8 vendor_ver; + u8 spec_ver; +}; + +/** + * esdhc_read*_fixup - Fixup the value read from incompatible eSDHC register + * to make it compatible with SD spec. + * + * @host: pointer to sdhci_host + * @spec_reg: SD spec register address + * @value: 32bit eSDHC register value on spec_reg address + * + * In SD spec, there are 8/16/32/64 bits registers, while all of eSDHC + * registers are 32 bits. There are differences in register size, register + * address, register function, bit position and function between eSDHC spec + * and SD spec. + * + * Return a fixed up register value + */ +static u32 esdhc_readl_fixup(struct sdhci_host *host, + int spec_reg, u32 value) { + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); + struct sdhci_esdhc *esdhc = pltfm_host->priv; u32 ret; - ret = in_be32(host->ioaddr + reg); /* * The bit of ADMA flag in eSDHC is not compatible with standard * SDHC register, so set fake flag SDHCI_CAN_DO_ADMA2 when ADMA is * supported by eSDHC. * And for many FSL eSDHC controller, the reset value of field - * SDHCI_CAN_DO_ADMA1 is one, but some of them can't support ADMA, + * SDHCI_CAN_DO_ADMA1 is 1, but some of them can't support ADMA, * only these vendor version is greater than 2.2/0x12 support ADMA. - * For FSL eSDHC, must aligned 4-byte, so use 0xFC to read the - * the verdor version number, oxFE is SDHCI_HOST_VERSION. */ - if ((reg == SDHCI_CAPABILITIES) && (ret & SDHCI_CAN_DO_ADMA1)) { - u32 tmp = in_be32(host->ioaddr + SDHCI_SLOT_INT_STATUS); - tmp = (tmp & SDHCI_VENDOR_VER_MASK) >> SDHCI_VENDOR_VER_SHIFT; - if (tmp > VENDOR_V_22) - ret |= SDHCI_CAN_DO_ADMA2; + if ((spec_reg == SDHCI_CAPABILITIES) && (value & SDHCI_CAN_DO_ADMA1)) { + if (esdhc->vendor_ver > VENDOR_V_22) { + ret = value | SDHCI_CAN_DO_ADMA2; + return ret; + } } - + ret = value; return ret; } -static u16 esdhc_readw(struct sdhci_host *host, int reg) +static u16 esdhc_readw_fixup(struct sdhci_host *host, + int spec_reg, u32 value) { u16 ret; - int base = reg & ~0x3; - int shift = (reg & 0x2) * 8; + int shift = (spec_reg & 0x2) * 8; - if (unlikely(reg == SDHCI_HOST_VERSION)) - ret = in_be32(host->ioaddr + base) & 0xffff; + if (spec_reg == SDHCI_HOST_VERSION) + ret = value & 0xffff; else - ret = (in_be32(host->ioaddr + base) >> shift) & 0xffff; + ret = (value >> shift) & 0xffff; return ret; } -static u8 esdhc_readb(struct sdhci_host *host, int reg) +static u8 esdhc_readb_fixup(struct sdhci_host *host, + int spec_reg, u32 value) { - int base = reg & ~0x3; - int shift = (reg & 0x3) * 8; - u8 ret = (in_be32(host->ioaddr + base) >> shift) & 0xff; + u8 ret; + u8 dma_bits; + int shift = (spec_reg & 0x3) * 8; + + ret = (value >> shift) & 0xff; /* * "DMA select" locates at offset 0x28 in SD specification, but on * P5020 or P3041, it locates at 0x29. */ - if (reg == SDHCI_HOST_CONTROL) { - u32 dma_bits; - - dma_bits = in_be32(host->ioaddr + reg); + if (spec_reg == SDHCI_HOST_CONTROL) { /* DMA select is 22,23 bits in Protocol Control Register */ - dma_bits = (dma_bits >> 5) & SDHCI_CTRL_DMA_MASK; - + dma_bits = (value >> 5) & SDHCI_CTRL_DMA_MASK; /* fixup the result */ ret &= ~SDHCI_CTRL_DMA_MASK; ret |= dma_bits; } - return ret; } -static void esdhc_writel(struct sdhci_host *host, u32 val, int reg) +/** + * esdhc_write*_fixup - Fixup the SD spec register value so that it could be + * written into eSDHC register. + * + * @host: pointer to sdhci_host + * @spec_reg: SD spec register address + * @value: 8/16/32bit SD spec register value that would be written + * @old_value: 32bit eSDHC register value on spec_reg address + * + * In SD spec, there are 8/16/32/64 bits registers, while all of eSDHC + * registers are 32 bits. There are differences in register size, register + * address, register function, bit position and function between eSDHC spec + * and SD spec. + * + * Return a fixed up register value + */ +static u32 esdhc_writel_fixup(struct sdhci_host *host, + int spec_reg, u32 value, u32 old_value) { + u32 ret; + /* - * Enable IRQSTATEN[BGESEN] is just to set IRQSTAT[BGE] - * when SYSCTL[RSTD]) is set for some special operations. - * No any impact other operation. + * Enabling IRQSTATEN[BGESEN] is just to set IRQSTAT[BGE] + * when SYSCTL[RSTD] is set for some special operations. + * No any impact on other operation. */ - if (reg == SDHCI_INT_ENABLE) - val |= SDHCI_INT_BLK_GAP; - sdhci_be32bs_writel(host, val, reg); + if (spec_reg == SDHCI_INT_ENABLE) + ret = value | SDHCI_INT_BLK_GAP; + else + ret = value; + + return ret; } -static void esdhc_writew(struct sdhci_host *host, u16 val, int reg) +static u32 esdhc_writew_fixup(struct sdhci_host *host, + int spec_reg, u16 value, u32 old_value) { - if (reg == SDHCI_BLOCK_SIZE) { + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); + int shift = (spec_reg & 0x2) * 8; + u32 ret; + + switch (spec_reg) { + case SDHCI_TRANSFER_MODE: + /* + * Postpone this write, we must do it together with a + * command write that is down below. Return old value. + */ + pltfm_host->xfer_mode_shadow = value; + return old_value; + case SDHCI_COMMAND: + ret = (value << 16) | pltfm_host->xfer_mode_shadow; + return ret; + } + + ret = old_value & (~(0xffff << shift)); + ret |= (value << shift); + + if (spec_reg == SDHCI_BLOCK_SIZE) { /* * Two last DMA bits are reserved, and first one is used for * non-standard blksz of 4096 bytes that we don't support * yet. So clear the DMA boundary bits. */ - val &= ~SDHCI_MAKE_BLKSZ(0x7, 0); + ret &= (~SDHCI_MAKE_BLKSZ(0x7, 0)); } - sdhci_be32bs_writew(host, val, reg); + return ret; } -static void esdhc_writeb(struct sdhci_host *host, u8 val, int reg) +static u32 esdhc_writeb_fixup(struct sdhci_host *host, + int spec_reg, u8 value, u32 old_value) { + u32 ret; + u32 dma_bits; + u8 tmp; + int shift = (spec_reg & 0x3) * 8; + + /* + * eSDHC doesn't have a standard power control register, so we do + * nothing here to avoid incorrect operation. + */ + if (spec_reg == SDHCI_POWER_CONTROL) + return old_value; /* * "DMA select" location is offset 0x28 in SD specification, but on * P5020 or P3041, it's located at 0x29. */ - if (reg == SDHCI_HOST_CONTROL) { - u32 dma_bits; - + if (spec_reg == SDHCI_HOST_CONTROL) { /* * If host control register is not standard, exit * this function */ if (host->quirks2 & SDHCI_QUIRK2_BROKEN_HOST_CONTROL) - return; + return old_value; /* DMA select is 22,23 bits in Protocol Control Register */ - dma_bits = (val & SDHCI_CTRL_DMA_MASK) << 5; - clrsetbits_be32(host->ioaddr + reg , SDHCI_CTRL_DMA_MASK << 5, - dma_bits); - val &= ~SDHCI_CTRL_DMA_MASK; - val |= in_be32(host->ioaddr + reg) & SDHCI_CTRL_DMA_MASK; + dma_bits = (value & SDHCI_CTRL_DMA_MASK) << 5; + ret = (old_value & (~(SDHCI_CTRL_DMA_MASK << 5))) | dma_bits; + tmp = (value & (~SDHCI_CTRL_DMA_MASK)) | + (old_value & SDHCI_CTRL_DMA_MASK); + ret = (ret & (~0xff)) | tmp; + + /* Prevent SDHCI core from writing reserved bits (e.g. HISPD) */ + ret &= ~ESDHC_HOST_CONTROL_RES; + return ret; } - /* Prevent SDHCI core from writing reserved bits (e.g. HISPD). */ - if (reg == SDHCI_HOST_CONTROL) - val &= ~ESDHC_HOST_CONTROL_RES; - sdhci_be32bs_writeb(host, val, reg); + ret = (old_value & (~(0xff << shift))) | (value << shift); + return ret; +} + +static u32 esdhc_be_readl(struct sdhci_host *host, int reg) +{ + u32 ret; + u32 value; + + value = ioread32be(host->ioaddr + reg); + ret = esdhc_readl_fixup(host, reg, value); + + return ret; +} + +static u32 esdhc_le_readl(struct sdhci_host *host, int reg) +{ + u32 ret; + u32 value; + + value = ioread32(host->ioaddr + reg); + ret = esdhc_readl_fixup(host, reg, value); + + return ret; +} + +static u16 esdhc_be_readw(struct sdhci_host *host, int reg) +{ + u16 ret; + u32 value; + int base = reg & ~0x3; + + value = ioread32be(host->ioaddr + base); + ret = esdhc_readw_fixup(host, reg, value); + return ret; +} + +static u16 esdhc_le_readw(struct sdhci_host *host, int reg) +{ + u16 ret; + u32 value; + int base = reg & ~0x3; + + value = ioread32(host->ioaddr + base); + ret = esdhc_readw_fixup(host, reg, value); + return ret; +} + +static u8 esdhc_be_readb(struct sdhci_host *host, int reg) +{ + u8 ret; + u32 value; + int base = reg & ~0x3; + + value = ioread32be(host->ioaddr + base); + ret = esdhc_readb_fixup(host, reg, value); + return ret; +} + +static u8 esdhc_le_readb(struct sdhci_host *host, int reg) +{ + u8 ret; + u32 value; + int base = reg & ~0x3; + + value = ioread32(host->ioaddr + base); + ret = esdhc_readb_fixup(host, reg, value); + return ret; +} + +static void esdhc_be_writel(struct sdhci_host *host, u32 val, int reg) +{ + u32 value; + + value = esdhc_writel_fixup(host, reg, val, 0); + iowrite32be(value, host->ioaddr + reg); +} + +static void esdhc_le_writel(struct sdhci_host *host, u32 val, int reg) +{ + u32 value; + + value = esdhc_writel_fixup(host, reg, val, 0); + iowrite32(value, host->ioaddr + reg); +} + +static void esdhc_be_writew(struct sdhci_host *host, u16 val, int reg) +{ + int base = reg & ~0x3; + u32 value; + u32 ret; + + value = ioread32be(host->ioaddr + base); + ret = esdhc_writew_fixup(host, reg, val, value); + if (reg != SDHCI_TRANSFER_MODE) + iowrite32be(ret, host->ioaddr + base); +} + +static void esdhc_le_writew(struct sdhci_host *host, u16 val, int reg) +{ + int base = reg & ~0x3; + u32 value; + u32 ret; + + value = ioread32(host->ioaddr + base); + ret = esdhc_writew_fixup(host, reg, val, value); + if (reg != SDHCI_TRANSFER_MODE) + iowrite32(ret, host->ioaddr + base); +} + +static void esdhc_be_writeb(struct sdhci_host *host, u8 val, int reg) +{ + int base = reg & ~0x3; + u32 value; + u32 ret; + + value = ioread32be(host->ioaddr + base); + ret = esdhc_writeb_fixup(host, reg, val, value); + iowrite32be(ret, host->ioaddr + base); +} + +static void esdhc_le_writeb(struct sdhci_host *host, u8 val, int reg) +{ + int base = reg & ~0x3; + u32 value; + u32 ret; + + value = ioread32(host->ioaddr + base); + ret = esdhc_writeb_fixup(host, reg, val, value); + iowrite32(ret, host->ioaddr + base); } /* @@ -149,19 +351,17 @@ static void esdhc_writeb(struct sdhci_host *host, u8 val, int reg) * For Continue, apply soft reset for data(SYSCTL[RSTD]); * and re-issue the entire read transaction from beginning. */ -static void esdhci_of_adma_workaround(struct sdhci_host *host, u32 intmask) +static void esdhc_of_adma_workaround(struct sdhci_host *host, u32 intmask) { - u32 tmp; + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); + struct sdhci_esdhc *esdhc = pltfm_host->priv; bool applicable; dma_addr_t dmastart; dma_addr_t dmanow; - tmp = in_be32(host->ioaddr + SDHCI_SLOT_INT_STATUS); - tmp = (tmp & SDHCI_VENDOR_VER_MASK) >> SDHCI_VENDOR_VER_SHIFT; - applicable = (intmask & SDHCI_INT_DATA_END) && - (intmask & SDHCI_INT_BLK_GAP) && - (tmp == VENDOR_V_23); + (intmask & SDHCI_INT_BLK_GAP) && + (esdhc->vendor_ver == VENDOR_V_23); if (!applicable) return; @@ -179,7 +379,11 @@ static void esdhci_of_adma_workaround(struct sdhci_host *host, u32 intmask) static int esdhc_of_enable_dma(struct sdhci_host *host) { - setbits32(host->ioaddr + ESDHC_DMA_SYSCTL, ESDHC_DMA_SNOOP); + u32 value; + + value = sdhci_readl(host, ESDHC_DMA_SYSCTL); + value |= ESDHC_DMA_SNOOP; + sdhci_writel(host, value, ESDHC_DMA_SYSCTL); return 0; } @@ -199,6 +403,8 @@ static unsigned int esdhc_of_get_min_clock(struct sdhci_host *host) static void esdhc_of_set_clock(struct sdhci_host *host, unsigned int clock) { + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); + struct sdhci_esdhc *esdhc = pltfm_host->priv; int pre_div = 1; int div = 1; u32 temp; @@ -209,9 +415,7 @@ static void esdhc_of_set_clock(struct sdhci_host *host, unsigned int clock) return; /* Workaround to start pre_div at 2 for VNN < VENDOR_V_23 */ - temp = esdhc_readw(host, SDHCI_HOST_VERSION); - temp = (temp & SDHCI_VENDOR_VER_MASK) >> SDHCI_VENDOR_VER_SHIFT; - if (temp < VENDOR_V_23) + if (esdhc->vendor_ver < VENDOR_V_23) pre_div = 2; /* Workaround to reduce the clock frequency for p1010 esdhc */ @@ -247,39 +451,26 @@ static void esdhc_of_set_clock(struct sdhci_host *host, unsigned int clock) mdelay(1); } -static void esdhc_of_platform_init(struct sdhci_host *host) -{ - u32 vvn; - - vvn = in_be32(host->ioaddr + SDHCI_SLOT_INT_STATUS); - vvn = (vvn & SDHCI_VENDOR_VER_MASK) >> SDHCI_VENDOR_VER_SHIFT; - if (vvn == VENDOR_V_22) - host->quirks2 |= SDHCI_QUIRK2_HOST_NO_CMD23; - - if (vvn > VENDOR_V_22) - host->quirks &= ~SDHCI_QUIRK_NO_BUSY_IRQ; -} - static void esdhc_pltfm_set_bus_width(struct sdhci_host *host, int width) { u32 ctrl; + ctrl = sdhci_readl(host, ESDHC_PROCTL); + ctrl &= (~ESDHC_CTRL_BUSWIDTH_MASK); switch (width) { case MMC_BUS_WIDTH_8: - ctrl = ESDHC_CTRL_8BITBUS; + ctrl |= ESDHC_CTRL_8BITBUS; break; case MMC_BUS_WIDTH_4: - ctrl = ESDHC_CTRL_4BITBUS; + ctrl |= ESDHC_CTRL_4BITBUS; break; default: - ctrl = 0; break; } - clrsetbits_be32(host->ioaddr + SDHCI_HOST_CONTROL, - ESDHC_CTRL_BUSWIDTH_MASK, ctrl); + sdhci_writel(host, ctrl, ESDHC_PROCTL); } static void esdhc_reset(struct sdhci_host *host, u8 mask) @@ -290,32 +481,13 @@ static void esdhc_reset(struct sdhci_host *host, u8 mask) sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE); } -static const struct sdhci_ops sdhci_esdhc_ops = { - .read_l = esdhc_readl, - .read_w = esdhc_readw, - .read_b = esdhc_readb, - .write_l = esdhc_writel, - .write_w = esdhc_writew, - .write_b = esdhc_writeb, - .set_clock = esdhc_of_set_clock, - .enable_dma = esdhc_of_enable_dma, - .get_max_clock = esdhc_of_get_max_clock, - .get_min_clock = esdhc_of_get_min_clock, - .platform_init = esdhc_of_platform_init, - .adma_workaround = esdhci_of_adma_workaround, - .set_bus_width = esdhc_pltfm_set_bus_width, - .reset = esdhc_reset, - .set_uhs_signaling = sdhci_set_uhs_signaling, -}; - #ifdef CONFIG_PM - static u32 esdhc_proctl; static int esdhc_of_suspend(struct device *dev) { struct sdhci_host *host = dev_get_drvdata(dev); - esdhc_proctl = sdhci_be32bs_readl(host, SDHCI_HOST_CONTROL); + esdhc_proctl = sdhci_readl(host, SDHCI_HOST_CONTROL); return sdhci_suspend_host(host); } @@ -328,9 +500,8 @@ static int esdhc_of_resume(struct device *dev) if (ret == 0) { /* Isn't this already done by sdhci_resume_host() ? --rmk */ esdhc_of_enable_dma(host); - sdhci_be32bs_writel(host, esdhc_proctl, SDHCI_HOST_CONTROL); + sdhci_writel(host, esdhc_proctl, SDHCI_HOST_CONTROL); } - return ret; } @@ -343,37 +514,103 @@ static const struct dev_pm_ops esdhc_pmops = { #define ESDHC_PMOPS NULL #endif -static const struct sdhci_pltfm_data sdhci_esdhc_pdata = { - /* - * card detection could be handled via GPIO - * eSDHC cannot support End Attribute in NOP ADMA descriptor - */ +static const struct sdhci_ops sdhci_esdhc_be_ops = { + .read_l = esdhc_be_readl, + .read_w = esdhc_be_readw, + .read_b = esdhc_be_readb, + .write_l = esdhc_be_writel, + .write_w = esdhc_be_writew, + .write_b = esdhc_be_writeb, + .set_clock = esdhc_of_set_clock, + .enable_dma = esdhc_of_enable_dma, + .get_max_clock = esdhc_of_get_max_clock, + .get_min_clock = esdhc_of_get_min_clock, + .adma_workaround = esdhc_of_adma_workaround, + .set_bus_width = esdhc_pltfm_set_bus_width, + .reset = esdhc_reset, + .set_uhs_signaling = sdhci_set_uhs_signaling, +}; + +static const struct sdhci_ops sdhci_esdhc_le_ops = { + .read_l = esdhc_le_readl, + .read_w = esdhc_le_readw, + .read_b = esdhc_le_readb, + .write_l = esdhc_le_writel, + .write_w = esdhc_le_writew, + .write_b = esdhc_le_writeb, + .set_clock = esdhc_of_set_clock, + .enable_dma = esdhc_of_enable_dma, + .get_max_clock = esdhc_of_get_max_clock, + .get_min_clock = esdhc_of_get_min_clock, + .adma_workaround = esdhc_of_adma_workaround, + .set_bus_width = esdhc_pltfm_set_bus_width, + .reset = esdhc_reset, + .set_uhs_signaling = sdhci_set_uhs_signaling, +}; + +static const struct sdhci_pltfm_data sdhci_esdhc_be_pdata = { .quirks = ESDHC_DEFAULT_QUIRKS | SDHCI_QUIRK_BROKEN_CARD_DETECTION | SDHCI_QUIRK_NO_CARD_NO_RESET | SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC, - .ops = &sdhci_esdhc_ops, + .ops = &sdhci_esdhc_be_ops, }; +static const struct sdhci_pltfm_data sdhci_esdhc_le_pdata = { + .quirks = ESDHC_DEFAULT_QUIRKS | SDHCI_QUIRK_BROKEN_CARD_DETECTION + | SDHCI_QUIRK_NO_CARD_NO_RESET + | SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC, + .ops = &sdhci_esdhc_le_ops, +}; + +static void esdhc_init(struct platform_device *pdev, struct sdhci_host *host) +{ + struct sdhci_pltfm_host *pltfm_host; + struct sdhci_esdhc *esdhc; + u16 host_ver; + + pltfm_host = sdhci_priv(host); + esdhc = devm_kzalloc(&pdev->dev, sizeof(struct sdhci_esdhc), + GFP_KERNEL); + + host_ver = sdhci_readw(host, SDHCI_HOST_VERSION); + esdhc->vendor_ver = (host_ver & SDHCI_VENDOR_VER_MASK) >> + SDHCI_VENDOR_VER_SHIFT; + esdhc->spec_ver = host_ver & SDHCI_SPEC_VER_MASK; + + pltfm_host->priv = esdhc; +} + static int sdhci_esdhc_probe(struct platform_device *pdev) { struct sdhci_host *host; struct device_node *np; int ret; - host = sdhci_pltfm_init(pdev, &sdhci_esdhc_pdata, 0); + np = pdev->dev.of_node; + + if (of_get_property(np, "little-endian", NULL)) + host = sdhci_pltfm_init(pdev, &sdhci_esdhc_le_pdata, 0); + else + host = sdhci_pltfm_init(pdev, &sdhci_esdhc_be_pdata, 0); + if (IS_ERR(host)) return PTR_ERR(host); + esdhc_init(pdev, host); + sdhci_get_of_property(pdev); - np = pdev->dev.of_node; if (of_device_is_compatible(np, "fsl,p5040-esdhc") || of_device_is_compatible(np, "fsl,p5020-esdhc") || of_device_is_compatible(np, "fsl,p4080-esdhc") || of_device_is_compatible(np, "fsl,p1020-esdhc") || - of_device_is_compatible(np, "fsl,t1040-esdhc")) + of_device_is_compatible(np, "fsl,t1040-esdhc") || + of_device_is_compatible(np, "fsl,ls1021a-esdhc")) host->quirks &= ~SDHCI_QUIRK_BROKEN_CARD_DETECTION; + if (of_device_is_compatible(np, "fsl,ls1021a-esdhc")) + host->quirks |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL; + if (of_device_is_compatible(np, "fsl,p2020-esdhc")) { /* * Freescale messed up with P2020 as it has a non-standard diff --git a/drivers/mmc/host/sdhci-pci.c b/drivers/mmc/host/sdhci-pci-core.c index b3b0a3e4fca1..cf7ad458b4f4 100644 --- a/drivers/mmc/host/sdhci-pci.c +++ b/drivers/mmc/host/sdhci-pci-core.c @@ -444,11 +444,7 @@ static int jmicron_pmos(struct sdhci_pci_chip *chip, int on) else scratch &= ~0x47; - ret = pci_write_config_byte(chip->pdev, 0xAE, scratch); - if (ret) - return ret; - - return 0; + return pci_write_config_byte(chip->pdev, 0xAE, scratch); } static int jmicron_probe(struct sdhci_pci_chip *chip) @@ -1113,6 +1109,62 @@ static const struct pci_device_id pci_ids[] = { }, { + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_DNV_EMMC, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .driver_data = (kernel_ulong_t)&sdhci_intel_byt_emmc, + }, + + { + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_BXT_EMMC, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .driver_data = (kernel_ulong_t)&sdhci_intel_byt_emmc, + }, + + { + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_BXT_SDIO, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .driver_data = (kernel_ulong_t)&sdhci_intel_byt_sdio, + }, + + { + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_BXT_SD, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .driver_data = (kernel_ulong_t)&sdhci_intel_byt_sd, + }, + + { + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_APL_EMMC, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .driver_data = (kernel_ulong_t)&sdhci_intel_byt_emmc, + }, + + { + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_APL_SDIO, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .driver_data = (kernel_ulong_t)&sdhci_intel_byt_sdio, + }, + + { + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_APL_SD, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .driver_data = (kernel_ulong_t)&sdhci_intel_byt_sd, + }, + + { .vendor = PCI_VENDOR_ID_O2, .device = PCI_DEVICE_ID_O2_8120, .subvendor = PCI_ANY_ID, diff --git a/drivers/mmc/host/sdhci-pci-o2micro.c b/drivers/mmc/host/sdhci-pci-o2micro.c index e2ec108dba0e..d48f03104b5b 100644 --- a/drivers/mmc/host/sdhci-pci-o2micro.c +++ b/drivers/mmc/host/sdhci-pci-o2micro.c @@ -60,7 +60,7 @@ static void o2_pci_led_enable(struct sdhci_pci_chip *chip) } -void sdhci_pci_o2_fujin2_pci_init(struct sdhci_pci_chip *chip) +static void sdhci_pci_o2_fujin2_pci_init(struct sdhci_pci_chip *chip) { u32 scratch_32; int ret; @@ -145,7 +145,6 @@ void sdhci_pci_o2_fujin2_pci_init(struct sdhci_pci_chip *chip) scratch_32 |= 0x00080000; pci_write_config_dword(chip->pdev, O2_SD_MISC_CTRL4, scratch_32); } -EXPORT_SYMBOL_GPL(sdhci_pci_o2_fujin2_pci_init); int sdhci_pci_o2_probe_slot(struct sdhci_pci_slot *slot) { @@ -179,7 +178,6 @@ int sdhci_pci_o2_probe_slot(struct sdhci_pci_slot *slot) return 0; } -EXPORT_SYMBOL_GPL(sdhci_pci_o2_probe_slot); int sdhci_pci_o2_probe(struct sdhci_pci_chip *chip) { @@ -385,11 +383,9 @@ int sdhci_pci_o2_probe(struct sdhci_pci_chip *chip) return 0; } -EXPORT_SYMBOL_GPL(sdhci_pci_o2_probe); int sdhci_pci_o2_resume(struct sdhci_pci_chip *chip) { sdhci_pci_o2_probe(chip); return 0; } -EXPORT_SYMBOL_GPL(sdhci_pci_o2_resume); diff --git a/drivers/mmc/host/sdhci-pci-o2micro.h b/drivers/mmc/host/sdhci-pci-o2micro.h index f7ffc908d9a0..770f53857211 100644 --- a/drivers/mmc/host/sdhci-pci-o2micro.h +++ b/drivers/mmc/host/sdhci-pci-o2micro.h @@ -64,8 +64,6 @@ #define O2_SD_VENDOR_SETTING 0x110 #define O2_SD_VENDOR_SETTING2 0x1C8 -extern void sdhci_pci_o2_fujin2_pci_init(struct sdhci_pci_chip *chip); - extern int sdhci_pci_o2_probe_slot(struct sdhci_pci_slot *slot); extern int sdhci_pci_o2_probe(struct sdhci_pci_chip *chip); diff --git a/drivers/mmc/host/sdhci-pci.h b/drivers/mmc/host/sdhci-pci.h index 541f1cad5247..d1a0b4db60db 100644 --- a/drivers/mmc/host/sdhci-pci.h +++ b/drivers/mmc/host/sdhci-pci.h @@ -24,6 +24,13 @@ #define PCI_DEVICE_ID_INTEL_SPT_EMMC 0x9d2b #define PCI_DEVICE_ID_INTEL_SPT_SDIO 0x9d2c #define PCI_DEVICE_ID_INTEL_SPT_SD 0x9d2d +#define PCI_DEVICE_ID_INTEL_DNV_EMMC 0x19db +#define PCI_DEVICE_ID_INTEL_BXT_SD 0x0aca +#define PCI_DEVICE_ID_INTEL_BXT_EMMC 0x0acc +#define PCI_DEVICE_ID_INTEL_BXT_SDIO 0x0ad0 +#define PCI_DEVICE_ID_INTEL_APL_SD 0x5aca +#define PCI_DEVICE_ID_INTEL_APL_EMMC 0x5acc +#define PCI_DEVICE_ID_INTEL_APL_SDIO 0x5ad0 /* * PCI registers diff --git a/drivers/mmc/host/sdhci-pltfm.c b/drivers/mmc/host/sdhci-pltfm.c index a207f5aaf62f..87fb5ea8ebe7 100644 --- a/drivers/mmc/host/sdhci-pltfm.c +++ b/drivers/mmc/host/sdhci-pltfm.c @@ -71,9 +71,7 @@ void sdhci_get_of_property(struct platform_device *pdev) struct device_node *np = pdev->dev.of_node; struct sdhci_host *host = platform_get_drvdata(pdev); struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); - const __be32 *clk; u32 bus_width; - int size; if (of_get_property(np, "sdhci,auto-cmd12", NULL)) host->quirks |= SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12; @@ -101,9 +99,7 @@ void sdhci_get_of_property(struct platform_device *pdev) of_device_is_compatible(np, "fsl,mpc8536-esdhc")) host->quirks |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL; - clk = of_get_property(np, "clock-frequency", &size); - if (clk && size == sizeof(*clk) && *clk) - pltfm_host->clock = be32_to_cpup(clk); + of_property_read_u32(np, "clock-frequency", &pltfm_host->clock); if (of_find_property(np, "keep-power-in-suspend", NULL)) host->mmc->pm_caps |= MMC_PM_KEEP_POWER; diff --git a/drivers/mmc/host/sdhci-sirf.c b/drivers/mmc/host/sdhci-sirf.c index 884294576356..34866f668dd7 100644 --- a/drivers/mmc/host/sdhci-sirf.c +++ b/drivers/mmc/host/sdhci-sirf.c @@ -50,7 +50,8 @@ static u32 sdhci_sirf_readl_le(struct sdhci_host *host, int reg) if (unlikely((reg == SDHCI_CAPABILITIES_1) && (host->mmc->caps & MMC_CAP_UHS_SDR50))) { /* fake CAP_1 register */ - val = SDHCI_SUPPORT_SDR50 | SDHCI_USE_SDR50_TUNING; + val = SDHCI_SUPPORT_DDR50 | + SDHCI_SUPPORT_SDR50 | SDHCI_USE_SDR50_TUNING; } if (unlikely(reg == SDHCI_SLOT_INT_STATUS)) { @@ -97,7 +98,7 @@ retry: clock_setting | phase, SDHCI_CLK_DELAY_SETTING); - if (!mmc_send_tuning(mmc)) { + if (!mmc_send_tuning(mmc, opcode, NULL)) { /* Tuning is successful at this tuning point */ tuned_phase_cnt++; dev_dbg(mmc_dev(mmc), "%s: Found good phase = %d\n", diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c index fbc7efdddcb5..b48565ed5616 100644 --- a/drivers/mmc/host/sdhci.c +++ b/drivers/mmc/host/sdhci.c @@ -1895,9 +1895,9 @@ static int sdhci_execute_tuning(struct mmc_host *mmc, u32 opcode) tuning_count = host->tuning_count; /* - * The Host Controller needs tuning only in case of SDR104 mode - * and for SDR50 mode when Use Tuning for SDR50 is set in the - * Capabilities register. + * The Host Controller needs tuning in case of SDR104 and DDR50 + * mode, and for SDR50 mode when Use Tuning for SDR50 is set in + * the Capabilities register. * If the Host Controller supports the HS200 mode then the * tuning function has to be executed. */ @@ -1917,6 +1917,7 @@ static int sdhci_execute_tuning(struct mmc_host *mmc, u32 opcode) break; case MMC_TIMING_UHS_SDR104: + case MMC_TIMING_UHS_DDR50: break; case MMC_TIMING_UHS_SDR50: @@ -2716,17 +2717,6 @@ int sdhci_resume_host(struct sdhci_host *host) host->ops->enable_dma(host); } - if (!device_may_wakeup(mmc_dev(host->mmc))) { - ret = request_threaded_irq(host->irq, sdhci_irq, - sdhci_thread_irq, IRQF_SHARED, - mmc_hostname(host->mmc), host); - if (ret) - return ret; - } else { - sdhci_disable_irq_wakeups(host); - disable_irq_wake(host->irq); - } - if ((host->mmc->pm_flags & MMC_PM_KEEP_POWER) && (host->quirks2 & SDHCI_QUIRK2_HOST_OFF_CARD_ON)) { /* Card keeps power but host controller does not */ @@ -2739,6 +2729,17 @@ int sdhci_resume_host(struct sdhci_host *host) mmiowb(); } + if (!device_may_wakeup(mmc_dev(host->mmc))) { + ret = request_threaded_irq(host->irq, sdhci_irq, + sdhci_thread_irq, IRQF_SHARED, + mmc_hostname(host->mmc), host); + if (ret) + return ret; + } else { + sdhci_disable_irq_wakeups(host); + disable_irq_wake(host->irq); + } + sdhci_enable_card_detection(host); return ret; diff --git a/drivers/mmc/host/sunxi-mmc.c b/drivers/mmc/host/sunxi-mmc.c index b981b8552e43..83de82bceafc 100644 --- a/drivers/mmc/host/sunxi-mmc.c +++ b/drivers/mmc/host/sunxi-mmc.c @@ -873,6 +873,13 @@ static void sunxi_mmc_request(struct mmc_host *mmc, struct mmc_request *mrq) spin_unlock_irqrestore(&host->lock, iflags); } +static int sunxi_mmc_card_busy(struct mmc_host *mmc) +{ + struct sunxi_mmc_host *host = mmc_priv(mmc); + + return !!(mmc_readl(host, REG_STAS) & SDXC_CARD_DATA_BUSY); +} + static const struct of_device_id sunxi_mmc_of_match[] = { { .compatible = "allwinner,sun4i-a10-mmc", }, { .compatible = "allwinner,sun5i-a13-mmc", }, @@ -888,6 +895,7 @@ static struct mmc_host_ops sunxi_mmc_ops = { .get_cd = mmc_gpio_get_cd, .enable_sdio_irq = sunxi_mmc_enable_sdio_irq, .hw_reset = sunxi_mmc_hw_reset, + .card_busy = sunxi_mmc_card_busy, }; static const struct sunxi_mmc_clk_delay sunxi_mmc_clk_delays[] = { diff --git a/drivers/mmc/host/vub300.c b/drivers/mmc/host/vub300.c index fbabbb82b354..1e819f98b94f 100644 --- a/drivers/mmc/host/vub300.c +++ b/drivers/mmc/host/vub300.c @@ -563,7 +563,7 @@ static void add_offloaded_reg(struct vub300_mmc_host *vub300, i += 1; continue; } - }; + } __add_offloaded_reg_to_fifo(vub300, register_access, func); } @@ -1372,7 +1372,7 @@ static void download_offload_pseudocode(struct vub300_mmc_host *vub300) l += snprintf(vub300->vub_name + l, sizeof(vub300->vub_name) - l, "_%04X%04X", sf->vendor, sf->device); - }; + } snprintf(vub300->vub_name + l, sizeof(vub300->vub_name) - l, ".bin"); dev_info(&vub300->udev->dev, "requesting offload firmware %s\n", vub300->vub_name); @@ -1893,7 +1893,7 @@ static int satisfy_request_from_offloaded_data(struct vub300_mmc_host *vub300, i += 1; continue; } - }; + } if (vub300->total_offload_count == 0) return 0; else if (vub300->fn[func].offload_count == 0) diff --git a/drivers/mmc/host/wbsd.c b/drivers/mmc/host/wbsd.c index ca183ea767b3..c3fd16d997ca 100644 --- a/drivers/mmc/host/wbsd.c +++ b/drivers/mmc/host/wbsd.c @@ -809,7 +809,7 @@ static void wbsd_request(struct mmc_host *mmc, struct mmc_request *mrq) cmd->error = -EINVAL; goto done; - }; + } } /* diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h index fdd0779ccdfa..eb0151bac50c 100644 --- a/include/linux/mmc/card.h +++ b/include/linux/mmc/card.h @@ -269,7 +269,6 @@ struct mmc_card { /* for byte mode */ #define MMC_QUIRK_NONSTD_SDIO (1<<2) /* non-standard SDIO card attached */ /* (missing CIA registers) */ -#define MMC_QUIRK_BROKEN_CLK_GATING (1<<3) /* clock gating the sdio bus will make card fail */ #define MMC_QUIRK_NONSTD_FUNC_IF (1<<4) /* SDIO card has nonstd function interfaces */ #define MMC_QUIRK_DISABLE_CD (1<<5) /* disconnect CD/DAT[3] resistor */ #define MMC_QUIRK_INAND_CMD38 (1<<6) /* iNAND devices have broken CMD38 */ diff --git a/include/linux/mmc/core.h b/include/linux/mmc/core.h index 258daf914c6d..37967b6da03c 100644 --- a/include/linux/mmc/core.h +++ b/include/linux/mmc/core.h @@ -152,10 +152,8 @@ extern int mmc_app_cmd(struct mmc_host *, struct mmc_card *); extern int mmc_wait_for_app_cmd(struct mmc_host *, struct mmc_card *, struct mmc_command *, int); extern void mmc_start_bkops(struct mmc_card *card, bool from_exception); -extern int __mmc_switch(struct mmc_card *, u8, u8, u8, unsigned int, bool, - bool, bool); extern int mmc_switch(struct mmc_card *, u8, u8, u8, unsigned int); -extern int mmc_send_tuning(struct mmc_host *host); +extern int mmc_send_tuning(struct mmc_host *host, u32 opcode, int *cmd_error); extern int mmc_get_ext_csd(struct mmc_card *card, u8 **new_ext_csd); #define MMC_ERASE_ARG 0x00000000 diff --git a/include/linux/mmc/dw_mmc.h b/include/linux/mmc/dw_mmc.h index 134c57422740..f67b2ec18e6d 100644 --- a/include/linux/mmc/dw_mmc.h +++ b/include/linux/mmc/dw_mmc.h @@ -16,6 +16,7 @@ #include <linux/scatterlist.h> #include <linux/mmc/core.h> +#include <linux/dmaengine.h> #define MAX_MCI_SLOTS 2 @@ -40,6 +41,17 @@ enum { struct mmc_data; +enum { + TRANS_MODE_PIO = 0, + TRANS_MODE_IDMAC, + TRANS_MODE_EDMAC +}; + +struct dw_mci_dma_slave { + struct dma_chan *ch; + enum dma_transfer_direction direction; +}; + /** * struct dw_mci - MMC controller state shared between all slots * @lock: Spinlock protecting the queue and associated data. @@ -154,7 +166,14 @@ struct dw_mci { dma_addr_t sg_dma; void *sg_cpu; const struct dw_mci_dma_ops *dma_ops; + /* For idmac */ unsigned int ring_size; + + /* For edmac */ + struct dw_mci_dma_slave *dms; + /* Registers's physical base address */ + void *phy_regs; + u32 cmd_status; u32 data_status; u32 stop_cmdr; @@ -208,8 +227,8 @@ struct dw_mci { struct dw_mci_dma_ops { /* DMA Ops */ int (*init)(struct dw_mci *host); - void (*start)(struct dw_mci *host, unsigned int sg_len); - void (*complete)(struct dw_mci *host); + int (*start)(struct dw_mci *host, unsigned int sg_len); + void (*complete)(void *host); void (*stop)(struct dw_mci *host); void (*cleanup)(struct dw_mci *host); void (*exit)(struct dw_mci *host); diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h index 83b81fd865f3..8673ffe3d86e 100644 --- a/include/linux/mmc/host.h +++ b/include/linux/mmc/host.h @@ -292,18 +292,6 @@ struct mmc_host { mmc_pm_flag_t pm_caps; /* supported pm features */ -#ifdef CONFIG_MMC_CLKGATE - int clk_requests; /* internal reference counter */ - unsigned int clk_delay; /* number of MCI clk hold cycles */ - bool clk_gated; /* clock gated */ - struct delayed_work clk_gate_work; /* delayed clock gate */ - unsigned int clk_old; /* old clock value cache */ - spinlock_t clk_lock; /* lock for clk fields */ - struct mutex clk_gate_mutex; /* mutex for clock gating */ - struct device_attribute clkgate_delay_attr; - unsigned long clkgate_delay; -#endif - /* host specific block data */ unsigned int max_seg_size; /* see blk_queue_max_segment_size */ unsigned short max_segs; /* see blk_queue_max_segments */ @@ -423,6 +411,7 @@ int mmc_regulator_get_ocrmask(struct regulator *supply); int mmc_regulator_set_ocr(struct mmc_host *mmc, struct regulator *supply, unsigned short vdd_bit); +int mmc_regulator_set_vqmmc(struct mmc_host *mmc, struct mmc_ios *ios); #else static inline int mmc_regulator_get_ocrmask(struct regulator *supply) { @@ -435,6 +424,12 @@ static inline int mmc_regulator_set_ocr(struct mmc_host *mmc, { return 0; } + +static inline int mmc_regulator_set_vqmmc(struct mmc_host *mmc, + struct mmc_ios *ios) +{ + return -EINVAL; +} #endif int mmc_regulator_get_supply(struct mmc_host *mmc); @@ -479,26 +474,6 @@ static inline int mmc_host_packed_wr(struct mmc_host *host) return host->caps2 & MMC_CAP2_PACKED_WR; } -#ifdef CONFIG_MMC_CLKGATE -void mmc_host_clk_hold(struct mmc_host *host); -void mmc_host_clk_release(struct mmc_host *host); -unsigned int mmc_host_clk_rate(struct mmc_host *host); - -#else -static inline void mmc_host_clk_hold(struct mmc_host *host) -{ -} - -static inline void mmc_host_clk_release(struct mmc_host *host) -{ -} - -static inline unsigned int mmc_host_clk_rate(struct mmc_host *host) -{ - return host->ios.clock; -} -#endif - static inline int mmc_card_hs(struct mmc_card *card) { return card->host->ios.timing == MMC_TIMING_SD_HS || diff --git a/include/uapi/linux/mmc/ioctl.h b/include/uapi/linux/mmc/ioctl.h index 1f5e68923929..7e385b83b9d8 100644 --- a/include/uapi/linux/mmc/ioctl.h +++ b/include/uapi/linux/mmc/ioctl.h @@ -45,8 +45,24 @@ struct mmc_ioc_cmd { }; #define mmc_ioc_cmd_set_data(ic, ptr) ic.data_ptr = (__u64)(unsigned long) ptr -#define MMC_IOC_CMD _IOWR(MMC_BLOCK_MAJOR, 0, struct mmc_ioc_cmd) +/** + * struct mmc_ioc_multi_cmd - multi command information + * @num_of_cmds: Number of commands to send. Must be equal to or less than + * MMC_IOC_MAX_CMDS. + * @cmds: Array of commands with length equal to 'num_of_cmds' + */ +struct mmc_ioc_multi_cmd { + __u64 num_of_cmds; + struct mmc_ioc_cmd cmds[0]; +}; +#define MMC_IOC_CMD _IOWR(MMC_BLOCK_MAJOR, 0, struct mmc_ioc_cmd) +/* + * MMC_IOC_MULTI_CMD: Used to send an array of MMC commands described by + * the structure mmc_ioc_multi_cmd. The MMC driver will issue all + * commands in array in sequence to card. + */ +#define MMC_IOC_MULTI_CMD _IOWR(MMC_BLOCK_MAJOR, 1, struct mmc_ioc_multi_cmd) /* * Since this ioctl is only meant to enhance (and not replace) normal access * to the mmc bus device, an upper data transfer limit of MMC_IOC_MAX_BYTES @@ -54,4 +70,5 @@ struct mmc_ioc_cmd { * block device operations. */ #define MMC_IOC_MAX_BYTES (512L * 256) +#define MMC_IOC_MAX_CMDS 255 #endif /* LINUX_MMC_IOCTL_H */ |