diff options
| -rw-r--r-- | Documentation/devicetree/bindings/net/sti-dwmac.txt | 89 | ||||
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c | 374 |
2 files changed, 253 insertions, 210 deletions
diff --git a/Documentation/devicetree/bindings/net/sti-dwmac.txt b/Documentation/devicetree/bindings/net/sti-dwmac.txt index 8c84d9a18f4c..6762a6b5da7e 100644 --- a/Documentation/devicetree/bindings/net/sti-dwmac.txt +++ b/Documentation/devicetree/bindings/net/sti-dwmac.txt @@ -1,58 +1,65 @@ STMicroelectronics SoC DWMAC glue layer controller +This file documents differences between the core properties in +Documentation/devicetree/bindings/net/stmmac.txt +and what is needed on STi platforms to program the stmmac glue logic. + The device node has following properties. Required properties: - compatible : Can be "st,stih415-dwmac", "st,stih416-dwmac", - "st,stid127-dwmac", "st,stih407-dwmac". - - reg : Offset of the glue configuration register map in system + "st,stih407-dwmac", "st,stid127-dwmac". + - reg : Offset of the glue configuration register map in system configuration regmap pointed by st,syscon property and size. - - - reg-names : Should be "sti-ethconf". - - - st,syscon : Should be phandle to system configuration node which + - st,syscon : Should be phandle to system configuration node which encompases this glue registers. + - st,gmac_en: this is to enable the gmac into a dedicated sysctl control + register available on STiH407 SoC. + - sti-ethconf: this is the gmac glue logic register to enable the GMAC, + select among the different modes and program the clk retiming. + - pinctrl-0: pin-control for all the MII mode supported. - - st,tx-retime-src: On STi Parts for Giga bit speeds, 125Mhz clocks can be - wired up in from different sources. One via TXCLK pin and other via CLK_125 - pin. This wiring is totally board dependent. However the retiming glue - logic should be configured accordingly. Possible values for this property - - "txclk" - if 125Mhz clock is wired up via txclk line. - "clk_125" - if 125Mhz clock is wired up via clk_125 line. - - This property is only valid for Giga bit setup( GMII, RGMII), and it is - un-used for non-giga bit (MII and RMII) setups. Also note that internal - clockgen can not generate stable 125Mhz clock. - - - st,ext-phyclk: This boolean property indicates who is generating the clock - for tx and rx. This property is only valid for RMII case where the clock can - be generated from the MAC or PHY. - - - clock-names: should be "sti-ethclk". - - clocks: Should point to ethernet clockgen which can generate phyclk. - +Optional properties: + - resets : phandle pointing to the system reset controller with correct + reset line index for ethernet reset. + - st,ext-phyclk: valid only for RMII where PHY can generate 50MHz clock or + MAC can generate it. + - st,tx-retime-src: This specifies which clk is wired up to the mac for + retimeing tx lines. This is totally board dependent and can take one of the + posssible values from "txclk", "clk_125" or "clkgen". + If not passed, the internal clock will be used by default. + - sti-ethclk: this is the phy clock. + - sti-clkconf: this is an extra sysconfig register, available in new SoCs, + to program the clk retiming. + - st,gmac_en: to enable the GMAC, this only is present in some SoCs; e.g. + STiH407. Example: -ethernet0: dwmac@fe810000 { - device_type = "network"; - compatible = "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710"; - reg = <0xfe810000 0x8000>, <0x8bc 0x4>; - reg-names = "stmmaceth", "sti-ethconf"; - interrupts = <0 133 0>, <0 134 0>, <0 135 0>; - interrupt-names = "macirq", "eth_wake_irq", "eth_lpi"; - phy-mode = "mii"; +ethernet0: dwmac@9630000 { + device_type = "network"; + status = "disabled"; + compatible = "st,stih407-dwmac", "snps,dwmac", "snps,dwmac-3.710"; + reg = <0x9630000 0x8000>, <0x80 0x4>; + reg-names = "stmmaceth", "sti-ethconf"; - st,syscon = <&syscfg_rear>; + st,syscon = <&syscfg_sbc_reg>; + st,gmac_en; + resets = <&softreset STIH407_ETH1_SOFTRESET>; + reset-names = "stmmaceth"; - snps,pbl = <32>; + interrupts = <GIC_SPI 98 IRQ_TYPE_NONE>, + <GIC_SPI 99 IRQ_TYPE_NONE>, + <GIC_SPI 100 IRQ_TYPE_NONE>; + interrupt-names = "macirq", "eth_wake_irq", "eth_lpi"; + + snps,pbl = <32>; snps,mixed-burst; - resets = <&softreset STIH416_ETH0_SOFTRESET>; - reset-names = "stmmaceth"; - pinctrl-0 = <&pinctrl_mii0>; - pinctrl-names = "default"; - clocks = <&CLK_S_GMAC0_PHY>; - clock-names = "stmmaceth"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rgmii1>; + + clock-names = "stmmaceth", "sti-ethclk"; + clocks = <&CLK_S_C0_FLEXGEN CLK_EXT2F_A9>, + <&CLK_S_C0_FLEXGEN CLK_ETH_PHY>; }; diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c index 552bbc17863c..ccfe7e510418 100644 --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c @@ -3,7 +3,7 @@ * * Copyright (C) 2003-2014 STMicroelectronics (R&D) Limited * Author: Srinivas Kandagatla <srinivas.kandagatla@st.com> - * + * Contributors: Giuseppe Cavallaro <peppe.cavallaro@st.com> * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -22,45 +22,22 @@ #include <linux/of.h> #include <linux/of_net.h> +#define DWMAC_125MHZ 125000000 +#define DWMAC_50MHZ 50000000 +#define DWMAC_25MHZ 25000000 +#define DWMAC_2_5MHZ 2500000 + +#define IS_PHY_IF_MODE_RGMII(iface) (iface == PHY_INTERFACE_MODE_RGMII || \ + iface == PHY_INTERFACE_MODE_RGMII_ID || \ + iface == PHY_INTERFACE_MODE_RGMII_RXID || \ + iface == PHY_INTERFACE_MODE_RGMII_TXID) + +#define IS_PHY_IF_MODE_GBIT(iface) (IS_PHY_IF_MODE_RGMII(iface) || \ + iface == PHY_INTERFACE_MODE_GMII) + +/* STiH4xx register definitions (STiH415/STiH416/STiH407/STiH410 families) */ + /** - * STi GMAC glue logic. - * -------------------- - * - * _ - * | \ - * --------|0 \ ETH_SEL_INTERNAL_NOTEXT_PHYCLK - * phyclk | |___________________________________________ - * | | | (phyclk-in) - * --------|1 / | - * int-clk |_ / | - * | _ - * | | \ - * |_______|1 \ ETH_SEL_TX_RETIME_CLK - * | |___________________________ - * | | (tx-retime-clk) - * _______|0 / - * | |_ / - * _ | - * | \ | - * --------|0 \ | - * clk_125 | |__| - * | | ETH_SEL_TXCLK_NOT_CLK125 - * --------|1 / - * txclk |_ / - * - * - * ETH_SEL_INTERNAL_NOTEXT_PHYCLK is valid only for RMII where PHY can - * generate 50MHz clock or MAC can generate it. - * This bit is configured by "st,ext-phyclk" property. - * - * ETH_SEL_TXCLK_NOT_CLK125 is only valid for gigabit modes, where the 125Mhz - * clock either comes from clk-125 pin or txclk pin. This configuration is - * totally driven by the board wiring. This bit is configured by - * "st,tx-retime-src" property. - * - * TXCLK configuration is different for different phy interface modes - * and changes according to link speed in modes like RGMII. - * * Below table summarizes the clock requirement and clock sources for * supported phy interface modes with link speeds. * ________________________________________________ @@ -74,44 +51,58 @@ * ------------------------------------------------ *| RGMII | 125Mhz | 25Mhz | *| | clk-125/txclk | clkgen | + *| | clkgen | | * ------------------------------------------------ *| RMII | n/a | 25Mhz | *| | |clkgen/phyclk-in | * ------------------------------------------------ * - * TX lines are always retimed with a clk, which can vary depending - * on the board configuration. Below is the table of these bits - * in eth configuration register depending on source of retime clk. - * - *--------------------------------------------------------------- - * src | tx_rt_clk | int_not_ext_phyclk | txclk_n_clk125| - *--------------------------------------------------------------- - * txclk | 0 | n/a | 1 | - *--------------------------------------------------------------- - * ck_125| 0 | n/a | 0 | - *--------------------------------------------------------------- - * phyclk| 1 | 0 | n/a | - *--------------------------------------------------------------- - * clkgen| 1 | 1 | n/a | - *--------------------------------------------------------------- + * Register Configuration + *------------------------------- + * src |BIT(8)| BIT(7)| BIT(6)| + *------------------------------- + * txclk | 0 | n/a | 1 | + *------------------------------- + * ck_125| 0 | n/a | 0 | + *------------------------------- + * phyclk| 1 | 0 | n/a | + *------------------------------- + * clkgen| 1 | 1 | n/a | + *------------------------------- */ - /* Register definition */ +#define STIH4XX_RETIME_SRC_MASK GENMASK(8, 6) +#define STIH4XX_ETH_SEL_TX_RETIME_CLK BIT(8) +#define STIH4XX_ETH_SEL_INTERNAL_NOTEXT_PHYCLK BIT(7) +#define STIH4XX_ETH_SEL_TXCLK_NOT_CLK125 BIT(6) + +/* STiD127 register definitions */ - /* 3 bits [8:6] - * [6:6] ETH_SEL_TXCLK_NOT_CLK125 - * [7:7] ETH_SEL_INTERNAL_NOTEXT_PHYCLK - * [8:8] ETH_SEL_TX_RETIME_CLK - * - */ +/** + *----------------------- + * src |BIT(6)| BIT(7)| + *----------------------- + * MII | 1 | n/a | + *----------------------- + * RMII | n/a | 1 | + * clkgen| | | + *----------------------- + * RMII | n/a | 0 | + * phyclk| | | + *----------------------- + * RGMII | 1 | n/a | + * clkgen| | | + *----------------------- + */ -#define TX_RETIME_SRC_MASK GENMASK(8, 6) -#define ETH_SEL_TX_RETIME_CLK BIT(8) -#define ETH_SEL_INTERNAL_NOTEXT_PHYCLK BIT(7) -#define ETH_SEL_TXCLK_NOT_CLK125 BIT(6) +#define STID127_RETIME_SRC_MASK GENMASK(7, 6) +#define STID127_ETH_SEL_INTERNAL_NOTEXT_PHYCLK BIT(7) +#define STID127_ETH_SEL_INTERNAL_NOTEXT_TXCLK BIT(6) -#define ENMII_MASK GENMASK(5, 5) -#define ENMII BIT(5) +#define ENMII_MASK GENMASK(5, 5) +#define ENMII BIT(5) +#define EN_MASK GENMASK(1, 1) +#define EN BIT(1) /** * 3 bits [4:2] @@ -120,29 +111,23 @@ * 010-SGMII * 100-RMII */ -#define MII_PHY_SEL_MASK GENMASK(4, 2) -#define ETH_PHY_SEL_RMII BIT(4) -#define ETH_PHY_SEL_SGMII BIT(3) -#define ETH_PHY_SEL_RGMII BIT(2) -#define ETH_PHY_SEL_GMII 0x0 -#define ETH_PHY_SEL_MII 0x0 - -#define IS_PHY_IF_MODE_RGMII(iface) (iface == PHY_INTERFACE_MODE_RGMII || \ - iface == PHY_INTERFACE_MODE_RGMII_ID || \ - iface == PHY_INTERFACE_MODE_RGMII_RXID || \ - iface == PHY_INTERFACE_MODE_RGMII_TXID) - -#define IS_PHY_IF_MODE_GBIT(iface) (IS_PHY_IF_MODE_RGMII(iface) || \ - iface == PHY_INTERFACE_MODE_GMII) +#define MII_PHY_SEL_MASK GENMASK(4, 2) +#define ETH_PHY_SEL_RMII BIT(4) +#define ETH_PHY_SEL_SGMII BIT(3) +#define ETH_PHY_SEL_RGMII BIT(2) +#define ETH_PHY_SEL_GMII 0x0 +#define ETH_PHY_SEL_MII 0x0 struct sti_dwmac { - int interface; - bool ext_phyclk; - bool is_tx_retime_src_clk_125; - struct clk *clk; - int reg; + int interface; /* MII interface */ + bool ext_phyclk; /* Clock from external PHY */ + u32 tx_retime_src; /* TXCLK Retiming*/ + struct clk *clk; /* PHY clock */ + int ctrl_reg; /* GMAC glue-logic control register */ + int clk_sel_reg; /* GMAC ext clk selection register */ struct device *dev; struct regmap *regmap; + u32 speed; }; static u32 phy_intf_sels[] = { @@ -162,74 +147,133 @@ enum { TX_RETIME_SRC_CLKGEN, }; -static const char *const tx_retime_srcs[] = { - [TX_RETIME_SRC_NA] = "", - [TX_RETIME_SRC_TXCLK] = "txclk", - [TX_RETIME_SRC_CLK_125] = "clk_125", - [TX_RETIME_SRC_PHYCLK] = "phyclk", - [TX_RETIME_SRC_CLKGEN] = "clkgen", -}; - -static u32 tx_retime_val[] = { - [TX_RETIME_SRC_TXCLK] = ETH_SEL_TXCLK_NOT_CLK125, +static u32 stih4xx_tx_retime_val[] = { + [TX_RETIME_SRC_TXCLK] = STIH4XX_ETH_SEL_TXCLK_NOT_CLK125, [TX_RETIME_SRC_CLK_125] = 0x0, - [TX_RETIME_SRC_PHYCLK] = ETH_SEL_TX_RETIME_CLK, - [TX_RETIME_SRC_CLKGEN] = ETH_SEL_TX_RETIME_CLK | - ETH_SEL_INTERNAL_NOTEXT_PHYCLK, + [TX_RETIME_SRC_PHYCLK] = STIH4XX_ETH_SEL_TX_RETIME_CLK, + [TX_RETIME_SRC_CLKGEN] = STIH4XX_ETH_SEL_TX_RETIME_CLK + | STIH4XX_ETH_SEL_INTERNAL_NOTEXT_PHYCLK, }; -static void setup_retime_src(struct sti_dwmac *dwmac, u32 spd) +static void stih4xx_fix_retime_src(void *priv, u32 spd) { - u32 src = 0, freq = 0; - - if (spd == SPEED_100) { - if (dwmac->interface == PHY_INTERFACE_MODE_MII || - dwmac->interface == PHY_INTERFACE_MODE_GMII) { - src = TX_RETIME_SRC_TXCLK; - } else if (dwmac->interface == PHY_INTERFACE_MODE_RMII) { - if (dwmac->ext_phyclk) { - src = TX_RETIME_SRC_PHYCLK; - } else { - src = TX_RETIME_SRC_CLKGEN; - freq = 50000000; - } - - } else if (IS_PHY_IF_MODE_RGMII(dwmac->interface)) { + struct sti_dwmac *dwmac = priv; + u32 src = dwmac->tx_retime_src; + u32 reg = dwmac->ctrl_reg; + u32 freq = 0; + + if (dwmac->interface == PHY_INTERFACE_MODE_MII) { + src = TX_RETIME_SRC_TXCLK; + } else if (dwmac->interface == PHY_INTERFACE_MODE_RMII) { + if (dwmac->ext_phyclk) { + src = TX_RETIME_SRC_PHYCLK; + } else { src = TX_RETIME_SRC_CLKGEN; - freq = 25000000; + freq = DWMAC_50MHZ; } + } else if (IS_PHY_IF_MODE_RGMII(dwmac->interface)) { + /* On GiGa clk source can be either ext or from clkgen */ + if (spd == SPEED_1000) { + freq = DWMAC_125MHZ; + } else { + /* Switch to clkgen for these speeds */ + src = TX_RETIME_SRC_CLKGEN; + if (spd == SPEED_100) + freq = DWMAC_25MHZ; + else if (spd == SPEED_10) + freq = DWMAC_2_5MHZ; + } + } - if (src == TX_RETIME_SRC_CLKGEN && dwmac->clk) - clk_set_rate(dwmac->clk, freq); + if (src == TX_RETIME_SRC_CLKGEN && dwmac->clk && freq) + clk_set_rate(dwmac->clk, freq); - } else if (spd == SPEED_1000) { - if (dwmac->is_tx_retime_src_clk_125) - src = TX_RETIME_SRC_CLK_125; - else - src = TX_RETIME_SRC_TXCLK; + regmap_update_bits(dwmac->regmap, reg, STIH4XX_RETIME_SRC_MASK, + stih4xx_tx_retime_val[src]); +} + +static void stid127_fix_retime_src(void *priv, u32 spd) +{ + struct sti_dwmac *dwmac = priv; + u32 reg = dwmac->ctrl_reg; + u32 freq = 0; + u32 val = 0; + + if (dwmac->interface == PHY_INTERFACE_MODE_MII) { + val = STID127_ETH_SEL_INTERNAL_NOTEXT_TXCLK; + } else if (dwmac->interface == PHY_INTERFACE_MODE_RMII) { + if (!dwmac->ext_phyclk) { + val = STID127_ETH_SEL_INTERNAL_NOTEXT_PHYCLK; + freq = DWMAC_50MHZ; + } + } else if (IS_PHY_IF_MODE_RGMII(dwmac->interface)) { + val = STID127_ETH_SEL_INTERNAL_NOTEXT_TXCLK; + if (spd == SPEED_1000) + freq = DWMAC_125MHZ; + else if (spd == SPEED_100) + freq = DWMAC_25MHZ; + else if (spd == SPEED_10) + freq = DWMAC_2_5MHZ; } - regmap_update_bits(dwmac->regmap, dwmac->reg, - TX_RETIME_SRC_MASK, tx_retime_val[src]); + if (dwmac->clk && freq) + clk_set_rate(dwmac->clk, freq); + + regmap_update_bits(dwmac->regmap, reg, STID127_RETIME_SRC_MASK, val); } -static void sti_dwmac_exit(struct platform_device *pdev, void *priv) +static void sti_dwmac_ctrl_init(struct sti_dwmac *dwmac) { - struct sti_dwmac *dwmac = priv; + struct regmap *regmap = dwmac->regmap; + int iface = dwmac->interface; + struct device *dev = dwmac->dev; + struct device_node *np = dev->of_node; + u32 reg = dwmac->ctrl_reg; + u32 val; if (dwmac->clk) - clk_disable_unprepare(dwmac->clk); + clk_prepare_enable(dwmac->clk); + + if (of_property_read_bool(np, "st,gmac_en")) + regmap_update_bits(regmap, reg, EN_MASK, EN); + + regmap_update_bits(regmap, reg, MII_PHY_SEL_MASK, phy_intf_sels[iface]); + + val = (iface == PHY_INTERFACE_MODE_REVMII) ? 0 : ENMII; + regmap_update_bits(regmap, reg, ENMII_MASK, val); +} + +static int stix4xx_init(struct platform_device *pdev, void *priv) +{ + struct sti_dwmac *dwmac = priv; + u32 spd = dwmac->speed; + + sti_dwmac_ctrl_init(dwmac); + + stih4xx_fix_retime_src(priv, spd); + + return 0; } -static void sti_fix_mac_speed(void *priv, unsigned int spd) +static int stid127_init(struct platform_device *pdev, void *priv) { struct sti_dwmac *dwmac = priv; + u32 spd = dwmac->speed; - setup_retime_src(dwmac, spd); + sti_dwmac_ctrl_init(dwmac); - return; + stid127_fix_retime_src(priv, spd); + + return 0; } +static void sti_dwmac_exit(struct platform_device *pdev, void *priv) +{ + struct sti_dwmac *dwmac = priv; + + if (dwmac->clk) + clk_disable_unprepare(dwmac->clk); +} static int sti_dwmac_parse_data(struct sti_dwmac *dwmac, struct platform_device *pdev) { @@ -245,6 +289,13 @@ static int sti_dwmac_parse_data(struct sti_dwmac *dwmac, res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "sti-ethconf"); if (!res) return -ENODATA; + dwmac->ctrl_reg = res->start; + + /* clk selection from extra syscfg register */ + dwmac->clk_sel_reg = -ENXIO; + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "sti-clkconf"); + if (res) + dwmac->clk_sel_reg = res->start; regmap = syscon_regmap_lookup_by_phandle(np, "st,syscon"); if (IS_ERR(regmap)) @@ -253,53 +304,31 @@ static int sti_dwmac_parse_data(struct sti_dwmac *dwmac, dwmac->dev = dev; dwmac->interface = of_get_phy_mode(np); dwmac->regmap = regmap; - dwmac->reg = res->start; dwmac->ext_phyclk = of_property_read_bool(np, "st,ext-phyclk"); - dwmac->is_tx_retime_src_clk_125 = false; + dwmac->tx_retime_src = TX_RETIME_SRC_NA; + dwmac->speed = SPEED_100; if (IS_PHY_IF_MODE_GBIT(dwmac->interface)) { const char *rs; + dwmac->tx_retime_src = TX_RETIME_SRC_CLKGEN; err = of_property_read_string(np, "st,tx-retime-src", &rs); - if (err < 0) { - dev_err(dev, "st,tx-retime-src not specified\n"); - return err; - } + if (err < 0) + dev_warn(dev, "Use internal clock source\n"); if (!strcasecmp(rs, "clk_125")) - dwmac->is_tx_retime_src_clk_125 = true; + dwmac->tx_retime_src = TX_RETIME_SRC_CLK_125; + else if (!strcasecmp(rs, "txclk")) + dwmac->tx_retime_src = TX_RETIME_SRC_TXCLK; + + dwmac->speed = SPEED_1000; } dwmac->clk = devm_clk_get(dev, "sti-ethclk"); - - if (IS_ERR(dwmac->clk)) + if (IS_ERR(dwmac->clk)) { + dev_warn(dev, "No phy clock provided...\n"); dwmac->clk = NULL; - - return 0; -} - -static int sti_dwmac_init(struct platform_device *pdev, void *priv) -{ - struct sti_dwmac *dwmac = priv; - struct regmap *regmap = dwmac->regmap; - int iface = dwmac->interface; - u32 reg = dwmac->reg; - u32 val, spd; - - if (dwmac->clk) - clk_prepare_enable(dwmac->clk); - - regmap_update_bits(regmap, reg, MII_PHY_SEL_MASK, phy_intf_sels[iface]); - - val = (iface == PHY_INTERFACE_MODE_REVMII) ? 0 : ENMII; - regmap_update_bits(regmap, reg, ENMII_MASK, val); - - if (IS_PHY_IF_MODE_GBIT(iface)) - spd = SPEED_1000; - else - spd = SPEED_100; - - setup_retime_src(dwmac, spd); + } return 0; } @@ -322,9 +351,16 @@ static void *sti_dwmac_setup(struct platform_device *pdev) return dwmac; } -const struct stmmac_of_data sti_gmac_data = { - .fix_mac_speed = sti_fix_mac_speed, +const struct stmmac_of_data stih4xx_dwmac_data = { + .fix_mac_speed = stih4xx_fix_retime_src, + .setup = sti_dwmac_setup, + .init = stix4xx_init, + .exit = sti_dwmac_exit, +}; + +const struct stmmac_of_data stid127_dwmac_data = { + .fix_mac_speed = stid127_fix_retime_src, .setup = sti_dwmac_setup, - .init = sti_dwmac_init, + .init = stid127_init, .exit = sti_dwmac_exit, }; |