diff options
31 files changed, 1428 insertions, 777 deletions
diff --git a/Documentation/devicetree/bindings/arm/spear/shirq.txt b/Documentation/devicetree/bindings/arm/spear/shirq.txt new file mode 100644 index 000000000000..13fbb8866bd6 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/spear/shirq.txt @@ -0,0 +1,48 @@ +* SPEAr Shared IRQ layer (shirq) + +SPEAr3xx architecture includes shared/multiplexed irqs for certain set +of devices. The multiplexor provides a single interrupt to parent +interrupt controller (VIC) on behalf of a group of devices. + +There can be multiple groups available on SPEAr3xx variants but not +exceeding 4. The number of devices in a group can differ, further they +may share same set of status/mask registers spanning across different +bit masks. Also in some cases the group may not have enable or other +registers. This makes software little complex. + +A single node in the device tree is used to describe the shared +interrupt multiplexor (one node for all groups). A group in the +interrupt controller shares config/control registers with other groups. +For example, a 32-bit interrupt enable/disable config register can +accommodate upto 4 interrupt groups. + +Required properties: + - compatible: should be, either of + - "st,spear300-shirq" + - "st,spear310-shirq" + - "st,spear320-shirq" + - interrupt-controller: Identifies the node as an interrupt controller. + - #interrupt-cells: should be <1> which basically contains the offset + (starting from 0) of interrupts for all the groups. + - reg: Base address and size of shirq registers. + - interrupts: The list of interrupts generated by the groups which are + then connected to a parent interrupt controller. Each group is + associated with one of the interrupts, hence number of interrupts (to + parent) is equal to number of groups. The format of the interrupt + specifier depends in the interrupt parent controller. + + Optional properties: + - interrupt-parent: pHandle of the parent interrupt controller, if not + inherited from the parent node. + +Example: + +The following is an example from the SPEAr320 SoC dtsi file. + +shirq: interrupt-controller@0xb3000000 { + compatible = "st,spear320-shirq"; + reg = <0xb3000000 0x1000>; + interrupts = <28 29 30 1>; + #interrupt-cells = <1>; + interrupt-controller; +}; diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 2af359cfe985..d0ae1d3a90d9 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -126,7 +126,8 @@ dtb-$(CONFIG_ARCH_SPEAR13XX) += spear1310-evb.dtb \ spear1340-evb.dtb dtb-$(CONFIG_ARCH_SPEAR3XX)+= spear300-evb.dtb \ spear310-evb.dtb \ - spear320-evb.dtb + spear320-evb.dtb \ + spear320-hmi.dtb dtb-$(CONFIG_ARCH_SPEAR6XX)+= spear600-evb.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun4i-cubieboard.dtb \ sun5i-olinuxino.dtb diff --git a/arch/arm/boot/dts/spear1310-evb.dts b/arch/arm/boot/dts/spear1310-evb.dts index 2e4c5727468e..b56a801e42a2 100644 --- a/arch/arm/boot/dts/spear1310-evb.dts +++ b/arch/arm/boot/dts/spear1310-evb.dts @@ -30,10 +30,14 @@ pinctrl-0 = <&state_default>; state_default: pinmux { - i2c0-pmx { + i2c0 { st,pins = "i2c0_grp"; st,function = "i2c0"; }; + i2s0 { + st,pins = "i2s0_grp"; + st,function = "i2s0"; + }; i2s1 { st,pins = "i2s1_grp"; st,function = "i2s1"; @@ -42,6 +46,10 @@ st,pins = "arm_gpio_grp"; st,function = "arm_gpio"; }; + clcd { + st,pins = "clcd_grp" , "clcd_high_res"; + st,function = "clcd"; + }; eth { st,pins = "gmii_grp"; st,function = "gmii"; @@ -74,11 +82,6 @@ st,pins = "i2c_1_2_grp"; st,function = "i2c_1_2"; }; - pci { - st,pins = "pcie0_grp","pcie1_grp", - "pcie2_grp"; - st,function = "pci"; - }; smii { st,pins = "smii_0_1_2_grp"; st,function = "smii_0_1_2"; @@ -88,6 +91,14 @@ "nand_16bit_grp"; st,function = "nand"; }; + sata { + st,pins = "sata0_grp"; + st,function = "sata"; + }; + pcie { + st,pins = "pcie1_grp", "pcie2_grp"; + st,function = "pci_express"; + }; }; }; @@ -109,9 +120,49 @@ fsmc: flash@b0000000 { status = "okay"; + + partition@0 { + label = "xloader"; + reg = <0x0 0x80000>; + }; + partition@80000 { + label = "u-boot"; + reg = <0x80000 0x140000>; + }; + partition@1C0000 { + label = "environment"; + reg = <0x1C0000 0x40000>; + }; + partition@200000 { + label = "dtb"; + reg = <0x200000 0x40000>; + }; + partition@240000 { + label = "linux"; + reg = <0x240000 0xC00000>; + }; + partition@E40000 { + label = "rootfs"; + reg = <0xE40000 0x0>; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + button@1 { + label = "wakeup"; + linux,code = <0x100>; + gpios = <&gpio0 7 0x4>; + debounce-interval = <20>; + gpio-key,wakeup = <1>; + }; }; gmac0: eth@e2000000 { + phy-mode = "gmii"; status = "okay"; }; @@ -135,23 +186,27 @@ }; partition@10000 { label = "u-boot"; - reg = <0x10000 0x40000>; + reg = <0x10000 0x50000>; + }; + partition@60000 { + label = "environment"; + reg = <0x60000 0x10000>; }; - partition@50000 { + partition@70000 { + label = "dtb"; + reg = <0x70000 0x10000>; + }; + partition@80000 { label = "linux"; - reg = <0x50000 0x2c0000>; + reg = <0x80000 0x310000>; }; - partition@310000 { + partition@390000 { label = "rootfs"; - reg = <0x310000 0x4f0000>; + reg = <0x390000 0x0>; }; }; }; - spi0: spi@e0100000 { - status = "okay"; - }; - ehci@e4800000 { status = "okay"; }; @@ -189,10 +244,6 @@ status = "okay"; }; - i2c1: i2c@5cd00000 { - status = "okay"; - }; - kbd@e0300000 { linux,keymap = < 0x00000001 0x00010002 @@ -277,6 +328,7 @@ 0x08080052 >; autorepeat; st,mode = <0>; + suspended_rate = <2000000>; status = "okay"; }; @@ -286,6 +338,81 @@ serial@e0000000 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + }; + + spi0: spi@e0100000 { + status = "okay"; + num-cs = <3>; + cs-gpios = <&gpio1 7 0>, <&spics 0>, <&spics 1>; + + stmpe610@0 { + compatible = "st,stmpe610"; + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <1000000>; + spi-cpha; + pl022,hierarchy = <0>; + pl022,interface = <0>; + pl022,slave-tx-disable; + pl022,com-mode = <0>; + pl022,rx-level-trig = <0>; + pl022,tx-level-trig = <0>; + pl022,ctrl-len = <0x7>; + pl022,wait-state = <0>; + pl022,duplex = <0>; + interrupts = <6 0x4>; + interrupt-parent = <&gpio1>; + irq-trigger = <0x2>; + + stmpe_touchscreen { + compatible = "st,stmpe-ts"; + ts,sample-time = <4>; + ts,mod-12b = <1>; + ts,ref-sel = <0>; + ts,adc-freq = <1>; + ts,ave-ctrl = <1>; + ts,touch-det-delay = <2>; + ts,settling = <2>; + ts,fraction-z = <7>; + ts,i-drive = <1>; + }; + }; + + m25p80@1 { + compatible = "st,m25p80"; + reg = <1>; + spi-max-frequency = <12000000>; + spi-cpol; + spi-cpha; + pl022,hierarchy = <0>; + pl022,interface = <0>; + pl022,slave-tx-disable; + pl022,com-mode = <0x2>; + pl022,rx-level-trig = <0>; + pl022,tx-level-trig = <0>; + pl022,ctrl-len = <0x11>; + pl022,wait-state = <0>; + pl022,duplex = <0>; + }; + + spidev@2 { + compatible = "spidev"; + reg = <2>; + spi-max-frequency = <25000000>; + spi-cpha; + pl022,hierarchy = <0>; + pl022,interface = <0>; + pl022,slave-tx-disable; + pl022,com-mode = <0x2>; + pl022,rx-level-trig = <0>; + pl022,tx-level-trig = <0>; + pl022,ctrl-len = <0x11>; + pl022,wait-state = <0>; + pl022,duplex = <0>; + }; }; wdt@ec800620 { diff --git a/arch/arm/boot/dts/spear1310.dtsi b/arch/arm/boot/dts/spear1310.dtsi index 7cd25eb4f8e0..1513c1927cc8 100644 --- a/arch/arm/boot/dts/spear1310.dtsi +++ b/arch/arm/boot/dts/spear1310.dtsi @@ -17,6 +17,18 @@ compatible = "st,spear1310"; ahb { + spics: spics@e0700000{ + compatible = "st,spear-spics-gpio"; + reg = <0xe0700000 0x1000>; + st-spics,peripcfg-reg = <0x3b0>; + st-spics,sw-enable-bit = <12>; + st-spics,cs-value-bit = <11>; + st-spics,cs-enable-mask = <3>; + st-spics,cs-enable-shift = <8>; + gpio-controller; + #gpio-cells = <2>; + }; + ahci@b1000000 { compatible = "snps,spear-ahci"; reg = <0xb1000000 0x10000>; @@ -43,6 +55,7 @@ reg = <0x5c400000 0x8000>; interrupts = <0 95 0x4>; interrupt-names = "macirq"; + phy-mode = "mii"; status = "disabled"; }; @@ -51,6 +64,7 @@ reg = <0x5c500000 0x8000>; interrupts = <0 96 0x4>; interrupt-names = "macirq"; + phy-mode = "mii"; status = "disabled"; }; @@ -59,6 +73,7 @@ reg = <0x5c600000 0x8000>; interrupts = <0 97 0x4>; interrupt-names = "macirq"; + phy-mode = "rmii"; status = "disabled"; }; @@ -67,6 +82,7 @@ reg = <0x5c700000 0x8000>; interrupts = <0 98 0x4>; interrupt-names = "macirq"; + phy-mode = "rgmii"; status = "disabled"; }; @@ -76,13 +92,6 @@ #gpio-range-cells = <2>; }; - spi1: spi@5d400000 { - compatible = "arm,pl022", "arm,primecell"; - reg = <0x5d400000 0x1000>; - interrupts = <0 99 0x4>; - status = "disabled"; - }; - apb { i2c1: i2c@5cd00000 { #address-cells = <1>; @@ -147,6 +156,15 @@ status = "disabled"; }; + spi1: spi@5d400000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0x5d400000 0x1000>; + interrupts = <0 99 0x4>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + serial@5c800000 { compatible = "arm,pl011", "arm,primecell"; reg = <0x5c800000 0x1000>; diff --git a/arch/arm/boot/dts/spear1340-evb.dts b/arch/arm/boot/dts/spear1340-evb.dts index 045f7123ffac..d6c30ae0a8d7 100644 --- a/arch/arm/boot/dts/spear1340-evb.dts +++ b/arch/arm/boot/dts/spear1340-evb.dts @@ -38,20 +38,15 @@ st,pins = "fsmc_8bit_grp"; st,function = "fsmc"; }; - kbd { - st,pins = "keyboard_row_col_grp", - "keyboard_col5_grp"; - st,function = "keyboard"; - }; uart0 { - st,pins = "uart0_grp", "uart0_enh_grp"; + st,pins = "uart0_grp"; st,function = "uart0"; }; - i2c0-pmx { + i2c0 { st,pins = "i2c0_grp"; st,function = "i2c0"; }; - i2c1-pmx { + i2c1 { st,pins = "i2c1_grp"; st,function = "i2c1"; }; @@ -64,14 +59,9 @@ st,function = "spdif_out"; }; ssp0 { - st,pins = "ssp0_grp", "ssp0_cs1_grp", - "ssp0_cs3_grp"; + st,pins = "ssp0_grp", "ssp0_cs1_grp", "ssp0_cs2_grp", "ssp0_cs3_grp"; st,function = "ssp0"; }; - pwm { - st,pins = "pwm2_grp", "pwm3_grp"; - st,function = "pwm"; - }; smi-pmx { st,pins = "smi_grp"; st,function = "smi"; @@ -84,6 +74,18 @@ st,pins = "gmii_grp", "rgmii_grp"; st,function = "gmac"; }; + cam0 { + st,pins = "cam0_grp"; + st,function = "cam0"; + }; + cam1 { + st,pins = "cam1_grp"; + st,function = "cam1"; + }; + cam2 { + st,pins = "cam2_grp"; + st,function = "cam2"; + }; cam3 { st,pins = "cam3_grp"; st,function = "cam3"; @@ -108,9 +110,18 @@ st,pins = "sata_grp"; st,function = "sata"; }; + pcie { + st,pins = "pcie_grp"; + st,function = "pcie"; + }; + }; }; + ahci@b1000000 { + status = "okay"; + }; + dma@ea800000 { status = "okay"; }; @@ -121,9 +132,35 @@ fsmc: flash@b0000000 { status = "okay"; + + partition@0 { + label = "xloader"; + reg = <0x0 0x200000>; + }; + partition@200000 { + label = "u-boot"; + reg = <0x200000 0x200000>; + }; + partition@400000 { + label = "environment"; + reg = <0x400000 0x100000>; + }; + partition@500000 { + label = "dtb"; + reg = <0x500000 0x100000>; + }; + partition@600000 { + label = "linux"; + reg = <0x600000 0xC00000>; + }; + partition@1200000 { + label = "rootfs"; + reg = <0x1200000 0x0>; + }; }; gmac0: eth@e2000000 { + phy-mode = "rgmii"; status = "okay"; }; @@ -147,31 +184,62 @@ }; partition@10000 { label = "u-boot"; - reg = <0x10000 0x40000>; + reg = <0x10000 0x50000>; + }; + partition@60000 { + label = "environment"; + reg = <0x60000 0x10000>; }; - partition@50000 { + partition@70000 { + label = "dtb"; + reg = <0x70000 0x10000>; + }; + partition@80000 { label = "linux"; - reg = <0x50000 0x2c0000>; + reg = <0x80000 0x310000>; }; - partition@310000 { + partition@390000 { label = "rootfs"; - reg = <0x310000 0x4f0000>; + reg = <0x390000 0x0>; }; }; }; - spi0: spi@e0100000 { + ehci@e4800000 { status = "okay"; }; - ehci@e4800000 { - status = "okay"; + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + button@1 { + label = "wakeup"; + linux,code = <0x100>; + gpios = <&gpio1 1 0x4>; + debounce-interval = <20>; + gpio-key,wakeup = <1>; + }; }; ehci@e5800000 { status = "okay"; }; + i2s0: i2s-play@b2400000 { + status = "okay"; + }; + + i2s1: i2s-rec@b2000000 { + status = "okay"; + }; + + incodec: dir-hifi { + compatible = "dummy,dir-hifi"; + status = "okay"; + }; + ohci@e4000000 { status = "okay"; }; @@ -180,11 +248,43 @@ status = "okay"; }; + outcodec: dit-hifi { + compatible = "dummy,dit-hifi"; + status = "okay"; + }; + + sound { + compatible = "spear,spear-evb"; + audio-controllers = <&spdif0 &spdif1 &i2s0 &i2s1>; + audio-codecs = <&incodec &outcodec &sta529 &sta529>; + codec_dai_name = "dir-hifi", "dit-hifi", "sta529-audio", "sta529-audio"; + stream_name = "spdif-cap", "spdif-play", "i2s-play", "i2s-cap"; + dai_name = "spdifin-pcm", "spdifout-pcm", "i2s0-pcm", "i2s1-pcm"; + nr_controllers = <4>; + status = "okay"; + }; + + spdif0: spdif-in@d0100000 { + status = "okay"; + }; + + spdif1: spdif-out@d0000000 { + status = "okay"; + }; + apb { adc@e0080000 { status = "okay"; }; + i2s-play@b2400000 { + status = "okay"; + }; + + i2s-rec@b2000000 { + status = "okay"; + }; + gpio0: gpio@e0600000 { status = "okay"; }; @@ -199,10 +299,36 @@ i2c0: i2c@e0280000 { status = "okay"; + + sta529: sta529@1a { + compatible = "st,sta529"; + reg = <0x1a>; + }; }; i2c1: i2c@b4000000 { status = "okay"; + + eeprom0@56 { + compatible = "st,eeprom"; + reg = <0x56>; + }; + + stmpe801@41 { + compatible = "st,stmpe801"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x41>; + interrupts = <4 0x4>; + interrupt-parent = <&gpio0>; + irq-trigger = <0x2>; + + stmpegpio: stmpe_gpio { + compatible = "st,stmpe-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + }; }; kbd@e0300000 { @@ -289,6 +415,7 @@ 0x08080052 >; autorepeat; st,mode = <0>; + suspended_rate = <2000000>; status = "okay"; }; @@ -298,10 +425,92 @@ serial@e0000000 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; }; serial@b4100000 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + }; + + spi0: spi@e0100000 { + status = "okay"; + num-cs = <3>; + cs-gpios = <&gpiopinctrl 80 0>, <&gpiopinctrl 24 0>, + <&gpiopinctrl 85 0>; + + m25p80@0 { + compatible = "m25p80"; + reg = <0>; + spi-max-frequency = <12000000>; + spi-cpol; + spi-cpha; + pl022,hierarchy = <0>; + pl022,interface = <0>; + pl022,slave-tx-disable; + pl022,com-mode = <0x2>; + pl022,rx-level-trig = <0>; + pl022,tx-level-trig = <0>; + pl022,ctrl-len = <0x11>; + pl022,wait-state = <0>; + pl022,duplex = <0>; + }; + + stmpe610@1 { + compatible = "st,stmpe610"; + spi-max-frequency = <1000000>; + spi-cpha; + reg = <1>; + pl022,hierarchy = <0>; + pl022,interface = <0>; + pl022,slave-tx-disable; + pl022,com-mode = <0>; + pl022,rx-level-trig = <0>; + pl022,tx-level-trig = <0>; + pl022,ctrl-len = <0x7>; + pl022,wait-state = <0>; + pl022,duplex = <0>; + interrupts = <100 0>; + interrupt-parent = <&gpiopinctrl>; + irq-trigger = <0x2>; + #address-cells = <1>; + #size-cells = <0>; + + stmpe_touchscreen { + compatible = "st,stmpe-ts"; + ts,sample-time = <4>; + ts,mod-12b = <1>; + ts,ref-sel = <0>; + ts,adc-freq = <1>; + ts,ave-ctrl = <1>; + ts,touch-det-delay = <2>; + ts,settling = <2>; + ts,fraction-z = <7>; + ts,i-drive = <1>; + }; + }; + + spidev@2 { + compatible = "spidev"; + reg = <2>; + spi-max-frequency = <25000000>; + spi-cpha; + pl022,hierarchy = <0>; + pl022,interface = <0>; + pl022,slave-tx-disable; + pl022,com-mode = <0x2>; + pl022,rx-level-trig = <0>; + pl022,tx-level-trig = <0>; + pl022,ctrl-len = <0x11>; + pl022,wait-state = <0>; + pl022,duplex = <0>; + }; + }; + + timer@ec800600 { + status = "okay"; }; wdt@ec800620 { diff --git a/arch/arm/boot/dts/spear1340.dtsi b/arch/arm/boot/dts/spear1340.dtsi index 6c09eb0a1b2b..34da11aa6795 100644 --- a/arch/arm/boot/dts/spear1340.dtsi +++ b/arch/arm/boot/dts/spear1340.dtsi @@ -17,6 +17,20 @@ compatible = "st,spear1340"; ahb { + + spics: spics@e0700000{ + compatible = "st,spear-spics-gpio"; + reg = <0xe0700000 0x1000>; + st-spics,peripcfg-reg = <0x42c>; + st-spics,sw-enable-bit = <21>; + st-spics,cs-value-bit = <20>; + st-spics,cs-enable-mask = <3>; + st-spics,cs-enable-shift = <18>; + gpio-controller; + #gpio-cells = <2>; + status = "disabled"; + }; + ahci@b1000000 { compatible = "snps,spear-ahci"; reg = <0xb1000000 0x10000>; @@ -24,15 +38,61 @@ status = "disabled"; }; + i2s-play@b2400000 { + compatible = "snps,designware-i2s"; + reg = <0xb2400000 0x10000>; + interrupt-names = "play_irq"; + interrupts = <0 98 0x4 + 0 99 0x4>; + play; + channel = <8>; + status = "disabled"; + }; + + i2s-rec@b2000000 { + compatible = "snps,designware-i2s"; + reg = <0xb2000000 0x10000>; + interrupt-names = "record_irq"; + interrupts = <0 100 0x4 + 0 101 0x4>; + record; + channel = <8>; + status = "disabled"; + }; + pinmux: pinmux@e0700000 { compatible = "st,spear1340-pinmux"; reg = <0xe0700000 0x1000>; #gpio-range-cells = <2>; }; + pwm: pwm@e0180000 { + compatible ="st,spear13xx-pwm"; + reg = <0xe0180000 0x1000>; + #pwm-cells = <2>; + status = "disabled"; + }; + + spdif-in@d0100000 { + compatible = "st,spdif-in"; + reg = < 0xd0100000 0x20000 + 0xd0110000 0x10000 >; + interrupts = <0 84 0x4>; + status = "disabled"; + }; + + spdif-out@d0000000 { + compatible = "st,spdif-out"; + reg = <0xd0000000 0x20000>; + interrupts = <0 85 0x4>; + status = "disabled"; + }; + spi1: spi@5d400000 { compatible = "arm,pl022", "arm,primecell"; reg = <0x5d400000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; interrupts = <0 99 0x4>; status = "disabled"; }; @@ -44,6 +104,7 @@ compatible = "snps,designware-i2c"; reg = <0xb4000000 0x1000>; interrupts = <0 104 0x4>; + write-16bit; status = "disabled"; }; diff --git a/arch/arm/boot/dts/spear13xx.dtsi b/arch/arm/boot/dts/spear13xx.dtsi index f7b84aced654..009096d1d2c3 100644 --- a/arch/arm/boot/dts/spear13xx.dtsi +++ b/arch/arm/boot/dts/spear13xx.dtsi @@ -64,12 +64,26 @@ bootargs = "console=ttyAMA0,115200"; }; + cpufreq { + compatible = "st,cpufreq-spear"; + cpufreq_tbl = < 166000 + 200000 + 250000 + 300000 + 400000 + 500000 + 600000 >; + status = "disable"; + }; + ahb { #address-cells = <1>; #size-cells = <1>; compatible = "simple-bus"; ranges = <0x50000000 0x50000000 0x10000000 0xb0000000 0xb0000000 0x10000000 + 0xd0000000 0xd0000000 0x02000000 + 0xd8000000 0xd8000000 0x01000000 0xe0000000 0xe0000000 0x10000000>; sdhci@b3000000 { @@ -81,7 +95,7 @@ cf@b2800000 { compatible = "arasan,cf-spear1340"; - reg = <0xb2800000 0x100>; + reg = <0xb2800000 0x1000>; interrupts = <0 29 0x4>; status = "disabled"; }; @@ -113,6 +127,7 @@ 0 23 0x4>; st,ale-off = <0x20000>; st,cle-off = <0x10000>; + st,mode = <2>; status = "disabled"; }; @@ -125,6 +140,13 @@ status = "disabled"; }; + pcm { + compatible = "st,pcm-audio"; + #address-cells = <0>; + #size-cells = <0>; + status = "disable"; + }; + smi: flash@ea000000 { compatible = "st,spear600-smi"; #address-cells = <1>; @@ -134,17 +156,11 @@ status = "disabled"; }; - spi0: spi@e0100000 { - compatible = "arm,pl022", "arm,primecell"; - reg = <0xe0100000 0x1000>; - interrupts = <0 31 0x4>; - status = "disabled"; - }; - ehci@e4800000 { compatible = "st,spear600-ehci", "usb-ehci"; reg = <0xe4800000 0x1000>; interrupts = <0 64 0x4>; + usbh0_id = <0>; status = "disabled"; }; @@ -152,6 +168,7 @@ compatible = "st,spear600-ehci", "usb-ehci"; reg = <0xe5800000 0x1000>; interrupts = <0 66 0x4>; + usbh1_id = <1>; status = "disabled"; }; @@ -159,6 +176,7 @@ compatible = "st,spear600-ohci", "usb-ohci"; reg = <0xe4000000 0x1000>; interrupts = <0 65 0x4>; + usbh0_id = <0>; status = "disabled"; }; @@ -166,6 +184,7 @@ compatible = "st,spear600-ohci", "usb-ohci"; reg = <0xe5000000 0x1000>; interrupts = <0 67 0x4>; + usbh1_id = <1>; status = "disabled"; }; @@ -175,6 +194,8 @@ compatible = "simple-bus"; ranges = <0x50000000 0x50000000 0x10000000 0xb0000000 0xb0000000 0x10000000 + 0xd0000000 0xd0000000 0x02000000 + 0xd8000000 0xd8000000 0x01000000 0xe0000000 0xe0000000 0x10000000>; gpio0: gpio@e0600000 { @@ -215,8 +236,35 @@ status = "disabled"; }; + i2s@e0180000 { + compatible = "st,designware-i2s"; + reg = <0xe0180000 0x1000>; + interrupt-names = "play_irq", "record_irq"; + interrupts = <0 10 0x4 + 0 11 0x4 >; + status = "disabled"; + }; + + i2s@e0200000 { + compatible = "st,designware-i2s"; + reg = <0xe0200000 0x1000>; + interrupt-names = "play_irq", "record_irq"; + interrupts = <0 26 0x4 + 0 53 0x4>; + status = "disabled"; + }; + + spi0: spi@e0100000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0xe0100000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 31 0x4>; + status = "disabled"; + }; + rtc@e0580000 { - compatible = "st,spear-rtc"; + compatible = "st,spear600-rtc"; reg = <0xe0580000 0x1000>; interrupts = <0 36 0x4>; status = "disabled"; @@ -232,7 +280,7 @@ adc@e0080000 { compatible = "st,spear600-adc"; reg = <0xe0080000 0x1000>; - interrupts = <0 44 0x4>; + interrupts = <0 12 0x4>; status = "disabled"; }; @@ -245,7 +293,8 @@ timer@ec800600 { compatible = "arm,cortex-a9-twd-timer"; reg = <0xec800600 0x20>; - interrupts = <1 13 0x301>; + interrupts = <1 13 0x4>; + status = "disabled"; }; wdt@ec800620 { @@ -257,6 +306,7 @@ thermal@e07008c4 { compatible = "st,thermal-spear1340"; reg = <0xe07008c4 0x4>; + thermal_flags = <0x7000>; }; }; }; diff --git a/arch/arm/boot/dts/spear300-evb.dts b/arch/arm/boot/dts/spear300-evb.dts index 1e7c7a8e2123..5de1431653e4 100644 --- a/arch/arm/boot/dts/spear300-evb.dts +++ b/arch/arm/boot/dts/spear300-evb.dts @@ -100,15 +100,23 @@ }; partition@10000 { label = "u-boot"; - reg = <0x10000 0x40000>; + reg = <0x10000 0x50000>; }; - partition@50000 { + partition@60000 { + label = "environment"; + reg = <0x60000 0x10000>; + }; + partition@70000 { + label = "dtb"; + reg = <0x70000 0x10000>; + }; + partition@80000 { label = "linux"; - reg = <0x50000 0x2c0000>; + reg = <0x80000 0x310000>; }; - partition@310000 { + partition@390000 { label = "rootfs"; - reg = <0x310000 0x4f0000>; + reg = <0x390000 0x0>; }; }; }; @@ -235,6 +243,8 @@ serial@d0000000 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; }; wdt@fc880000 { diff --git a/arch/arm/boot/dts/spear300.dtsi b/arch/arm/boot/dts/spear300.dtsi index ed3627c116cc..090adc656015 100644 --- a/arch/arm/boot/dts/spear300.dtsi +++ b/arch/arm/boot/dts/spear300.dtsi @@ -27,7 +27,7 @@ }; clcd@60000000 { - compatible = "arm,clcd-pl110", "arm,primecell"; + compatible = "arm,pl110", "arm,primecell"; reg = <0x60000000 0x1000>; interrupts = <30>; status = "disabled"; @@ -52,6 +52,14 @@ status = "disabled"; }; + shirq: interrupt-controller@0x50000000 { + compatible = "st,spear300-shirq"; + reg = <0x50000000 0x1000>; + interrupts = <28>; + #interrupt-cells = <1>; + interrupt-controller; + }; + apb { #address-cells = <1>; #size-cells = <1>; @@ -64,12 +72,16 @@ compatible = "arm,pl061", "arm,primecell"; gpio-controller; reg = <0xa9000000 0x1000>; + interrupts = <8>; + interrupt-parent = <&shirq>; status = "disabled"; }; kbd@a0000000 { compatible = "st,spear300-kbd"; reg = <0xa0000000 0x1000>; + interrupts = <7>; + interrupt-parent = <&shirq>; status = "disabled"; }; }; diff --git a/arch/arm/boot/dts/spear310-evb.dts b/arch/arm/boot/dts/spear310-evb.dts index b00544e0cd5d..b09632963d15 100644 --- a/arch/arm/boot/dts/spear310-evb.dts +++ b/arch/arm/boot/dts/spear310-evb.dts @@ -114,15 +114,23 @@ }; partition@10000 { label = "u-boot"; - reg = <0x10000 0x40000>; + reg = <0x10000 0x50000>; }; - partition@50000 { + partition@60000 { + label = "environment"; + reg = <0x60000 0x10000>; + }; + partition@70000 { + label = "dtb"; + reg = <0x70000 0x10000>; + }; + partition@80000 { label = "linux"; - reg = <0x50000 0x2c0000>; + reg = <0x80000 0x310000>; }; - partition@310000 { + partition@390000 { label = "rootfs"; - reg = <0x310000 0x4f0000>; + reg = <0x390000 0x0>; }; }; }; @@ -158,26 +166,38 @@ serial@d0000000 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; }; serial@b2000000 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; }; serial@b2080000 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; }; serial@b2100000 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; }; serial@b2180000 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; }; serial@b2200000 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; }; wdt@fc880000 { diff --git a/arch/arm/boot/dts/spear310.dtsi b/arch/arm/boot/dts/spear310.dtsi index 930303e48df9..e814e5e97083 100644 --- a/arch/arm/boot/dts/spear310.dtsi +++ b/arch/arm/boot/dts/spear310.dtsi @@ -40,6 +40,14 @@ status = "disabled"; }; + shirq: interrupt-controller@0xb4000000 { + compatible = "st,spear310-shirq"; + reg = <0xb4000000 0x1000>; + interrupts = <28 29 30 1>; + #interrupt-cells = <1>; + interrupt-controller; + }; + apb { #address-cells = <1>; #size-cells = <1>; @@ -50,30 +58,40 @@ serial@b2000000 { compatible = "arm,pl011", "arm,primecell"; reg = <0xb2000000 0x1000>; + interrupts = <8>; + interrupt-parent = <&shirq>; status = "disabled"; }; serial@b2080000 { compatible = "arm,pl011", "arm,primecell"; reg = <0xb2080000 0x1000>; + interrupts = <9>; + interrupt-parent = <&shirq>; status = "disabled"; }; serial@b2100000 { compatible = "arm,pl011", "arm,primecell"; reg = <0xb2100000 0x1000>; + interrupts = <10>; + interrupt-parent = <&shirq>; status = "disabled"; }; serial@b2180000 { compatible = "arm,pl011", "arm,primecell"; reg = <0xb2180000 0x1000>; + interrupts = <11>; + interrupt-parent = <&shirq>; status = "disabled"; }; serial@b2200000 { compatible = "arm,pl011", "arm,primecell"; reg = <0xb2200000 0x1000>; + interrupts = <12>; + interrupt-parent = <&shirq>; status = "disabled"; }; diff --git a/arch/arm/boot/dts/spear320-evb.dts b/arch/arm/boot/dts/spear320-evb.dts index ad4bfc68ee05..fdedbb514102 100644 --- a/arch/arm/boot/dts/spear320-evb.dts +++ b/arch/arm/boot/dts/spear320-evb.dts @@ -76,20 +76,12 @@ st,function = "mii2"; }; pwm0_1 { - st,pins = "pwm0_1_pin_14_15_grp"; + st,pins = "pwm0_1_pin_37_38_grp"; st,function = "pwm0_1"; }; - pwm2 { - st,pins = "pwm2_pin_13_grp"; - st,function = "pwm2"; - }; }; }; - clcd@90000000 { - status = "okay"; - }; - dma@fc400000 { status = "okay"; }; @@ -103,6 +95,7 @@ }; sdhci@70000000 { + power-gpio = <&gpiopinctrl 61 1>; status = "okay"; }; @@ -122,15 +115,23 @@ }; partition@10000 { label = "u-boot"; - reg = <0x10000 0x40000>; + reg = <0x10000 0x50000>; + }; + partition@60000 { + label = "environment"; + reg = <0x60000 0x10000>; + }; + partition@70000 { + label = "dtb"; + reg = <0x70000 0x10000>; }; - partition@50000 { + partition@80000 { label = "linux"; - reg = <0x50000 0x2c0000>; + reg = <0x80000 0x310000>; }; - partition@310000 { + partition@390000 { label = "rootfs"; - reg = <0x310000 0x4f0000>; + reg = <0x390000 0x0>; }; }; }; @@ -182,14 +183,20 @@ serial@d0000000 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; }; serial@a3000000 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; }; serial@a4000000 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; }; wdt@fc880000 { diff --git a/arch/arm/boot/dts/spear320-hmi.dts b/arch/arm/boot/dts/spear320-hmi.dts new file mode 100644 index 000000000000..3075d2d3a8be --- /dev/null +++ b/arch/arm/boot/dts/spear320-hmi.dts @@ -0,0 +1,305 @@ +/* + * DTS file for SPEAr320 Evaluation Baord + * + * Copyright 2012 Shiraz Hashim <shiraz.hashim@st.com> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +/include/ "spear320.dtsi" + +/ { + model = "ST SPEAr320 HMI Board"; + compatible = "st,spear320-hmi", "st,spear320"; + #address-cells = <1>; + #size-cells = <1>; + + memory { + reg = <0 0x40000000>; + }; + + ahb { + pinmux@b3000000 { + st,pinmux-mode = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + i2c0 { + st,pins = "i2c0_grp"; + st,function = "i2c0"; + }; + ssp0 { + st,pins = "ssp0_grp"; + st,function = "ssp0"; + }; + uart0 { + st,pins = "uart0_grp"; + st,function = "uart0"; + }; + clcd { + st,pins = "clcd_grp"; + st,function = "clcd"; + }; + fsmc { + st,pins = "fsmc_8bit_grp"; + st,function = "fsmc"; + }; + sdhci { + st,pins = "sdhci_cd_12_grp"; + st,function = "sdhci"; + }; + i2s { + st,pins = "i2s_grp"; + st,function = "i2s"; + }; + uart1 { + st,pins = "uart1_grp"; + st,function = "uart1"; + }; + uart2 { + st,pins = "uart2_grp"; + st,function = "uart2"; + }; + can0 { + st,pins = "can0_grp"; + st,function = "can0"; + }; + can1 { + st,pins = "can1_grp"; + st,function = "can1"; + }; + mii0_1 { + st,pins = "rmii0_1_grp"; + st,function = "mii0_1"; + }; + pwm0_1 { + st,pins = "pwm0_1_pin_37_38_grp"; + st,function = "pwm0_1"; + }; + pwm2 { + st,pins = "pwm2_pin_34_grp"; + st,function = "pwm2"; + }; + }; + }; + + clcd@90000000 { + status = "okay"; + }; + + dma@fc400000 { + status = "okay"; + }; + + ehci@e1800000 { + status = "okay"; + }; + + fsmc: flash@4c000000 { + status = "okay"; + + partition@0 { + label = "xloader"; + reg = <0x0 0x80000>; + }; + partition@80000 { + label = "u-boot"; + reg = <0x80000 0x140000>; + }; + partition@1C0000 { + label = "environment"; + reg = <0x1C0000 0x40000>; + }; + partition@200000 { + label = "dtb"; + reg = <0x200000 0x40000>; + }; + partition@240000 { + label = "linux"; + reg = <0x240000 0xC00000>; + }; + partition@E40000 { + label = "rootfs"; + reg = <0xE40000 0x0>; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + button@1 { + label = "user button 1"; + linux,code = <0x100>; + gpios = <&stmpegpio 3 0x4>; + debounce-interval = <20>; + gpio-key,wakeup = <1>; + }; + + button@2 { + label = "user button 2"; + linux,code = <0x200>; + gpios = <&stmpegpio 2 0x4>; + debounce-interval = <20>; + gpio-key,wakeup = <1>; + }; + }; + + ohci@e1900000 { + status = "okay"; + }; + + ohci@e2100000 { + status = "okay"; + }; + + pwm: pwm@a8000000 { + status = "okay"; + }; + + sdhci@70000000 { + power-gpio = <&gpiopinctrl 50 1>; + power_always_enb; + status = "okay"; + }; + + smi: flash@fc000000 { + status = "okay"; + clock-rate=<50000000>; + + flash@f8000000 { + #address-cells = <1>; + #size-cells = <1>; + reg = <0xf8000000 0x800000>; + st,smi-fast-mode; + + partition@0 { + label = "xloader"; + reg = <0x0 0x10000>; + }; + partition@10000 { + label = "u-boot"; + reg = <0x10000 0x50000>; + }; + partition@60000 { + label = "environment"; + reg = <0x60000 0x10000>; + }; + partition@70000 { + label = "dtb"; + reg = <0x70000 0x10000>; + }; + partition@80000 { + label = "linux"; + reg = <0x80000 0x310000>; + }; + partition@390000 { + label = "rootfs"; + reg = <0x390000 0x0>; + }; + }; + }; + + spi0: spi@d0100000 { + status = "okay"; + }; + + spi1: spi@a5000000 { + status = "okay"; + }; + + spi2: spi@a6000000 { + status = "okay"; + }; + + usbd@e1100000 { + status = "okay"; + }; + + apb { + gpio0: gpio@fc980000 { + status = "okay"; + }; + + gpio@b3000000 { + status = "okay"; + }; + + i2c0: i2c@d0180000 { + status = "okay"; + + stmpe811@41 { + compatible = "st,stmpe811"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x41>; + irq-over-gpio; + irq-gpios = <&gpiopinctrl 29 0x4>; + id = <0>; + blocks = <0x5>; + irq-trigger = <0x1>; + + stmpegpio: stmpe-gpio { + compatible = "stmpe,gpio"; + reg = <0>; + gpio-controller; + #gpio-cells = <2>; + gpio,norequest-mask = <0xF3>; + }; + + stmpe610-ts { + compatible = "stmpe,ts"; + reg = <0>; + ts,sample-time = <4>; + ts,mod-12b = <1>; + ts,ref-sel = <0>; + ts,adc-freq = <1>; + ts,ave-ctrl = <1>; + ts,touch-det-delay = <3>; + ts,settling = <4>; + ts,fraction-z = <7>; + ts,i-drive = <1>; + }; + }; + }; + + i2c1: i2c@a7000000 { + status = "okay"; + }; + + rtc@fc900000 { + status = "okay"; + }; + + serial@d0000000 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + }; + + serial@a3000000 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + }; + + serial@a4000000 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + }; + + wdt@fc880000 { + status = "okay"; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/spear320.dtsi b/arch/arm/boot/dts/spear320.dtsi index 67d7ada71275..c056a84deabf 100644 --- a/arch/arm/boot/dts/spear320.dtsi +++ b/arch/arm/boot/dts/spear320.dtsi @@ -28,9 +28,10 @@ }; clcd@90000000 { - compatible = "arm,clcd-pl110", "arm,primecell"; + compatible = "arm,pl110", "arm,primecell"; reg = <0x90000000 0x1000>; - interrupts = <33>; + interrupts = <8>; + interrupt-parent = <&shirq>; status = "disabled"; }; @@ -49,27 +50,51 @@ sdhci@70000000 { compatible = "st,sdhci-spear"; reg = <0x70000000 0x100>; - interrupts = <29>; + interrupts = <10>; + interrupt-parent = <&shirq>; status = "disabled"; }; + shirq: interrupt-controller@0xb3000000 { + compatible = "st,spear320-shirq"; + reg = <0xb3000000 0x1000>; + interrupts = <30 28 29 1>; + #interrupt-cells = <1>; + interrupt-controller; + }; + spi1: spi@a5000000 { compatible = "arm,pl022", "arm,primecell"; reg = <0xa5000000 0x1000>; + interrupts = <15>; + interrupt-parent = <&shirq>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; spi2: spi@a6000000 { compatible = "arm,pl022", "arm,primecell"; reg = <0xa6000000 0x1000>; + interrupts = <16>; + interrupt-parent = <&shirq>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; + pwm: pwm@a8000000 { + compatible ="st,spear-pwm"; + reg = <0xa8000000 0x1000>; + #pwm-cells = <2>; + status = "disabled"; + }; + apb { #address-cells = <1>; #size-cells = <1>; compatible = "simple-bus"; - ranges = <0xa0000000 0xa0000000 0x10000000 + ranges = <0xa0000000 0xa0000000 0x20000000 0xd0000000 0xd0000000 0x30000000>; i2c1: i2c@a7000000 { @@ -77,18 +102,24 @@ #size-cells = <0>; compatible = "snps,designware-i2c"; reg = <0xa7000000 0x1000>; + interrupts = <21>; + interrupt-parent = <&shirq>; status = "disabled"; }; serial@a3000000 { compatible = "arm,pl011", "arm,primecell"; reg = <0xa3000000 0x1000>; + interrupts = <13>; + interrupt-parent = <&shirq>; status = "disabled"; }; serial@a4000000 { compatible = "arm,pl011", "arm,primecell"; reg = <0xa4000000 0x1000>; + interrupts = <14>; + interrupt-parent = <&shirq>; status = "disabled"; }; diff --git a/arch/arm/boot/dts/spear3xx.dtsi b/arch/arm/boot/dts/spear3xx.dtsi index 3a8bb5736928..c2a852d43c48 100644 --- a/arch/arm/boot/dts/spear3xx.dtsi +++ b/arch/arm/boot/dts/spear3xx.dtsi @@ -53,6 +53,7 @@ reg = <0xe0800000 0x8000>; interrupts = <23 22>; interrupt-names = "macirq", "eth_wake_irq"; + phy-mode = "mii"; status = "disabled"; }; @@ -69,6 +70,8 @@ compatible = "arm,pl022", "arm,primecell"; reg = <0xd0100000 0x1000>; interrupts = <20>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; @@ -120,7 +123,7 @@ }; rtc@fc900000 { - compatible = "st,spear-rtc"; + compatible = "st,spear600-rtc"; reg = <0xfc900000 0x1000>; interrupts = <10>; status = "disabled"; diff --git a/arch/arm/boot/dts/spear600-evb.dts b/arch/arm/boot/dts/spear600-evb.dts index 1119c22c9a82..d865a891776d 100644 --- a/arch/arm/boot/dts/spear600-evb.dts +++ b/arch/arm/boot/dts/spear600-evb.dts @@ -24,15 +24,35 @@ }; ahb { + clcd@fc200000 { + status = "okay"; + }; + dma@fc400000 { status = "okay"; }; + ehci@e1800000 { + status = "okay"; + }; + + ehci@e2000000 { + status = "okay"; + }; + gmac: ethernet@e0800000 { phy-mode = "gmii"; status = "okay"; }; + ohci@e1900000 { + status = "okay"; + }; + + ohci@e2100000 { + status = "okay"; + }; + smi: flash@fc000000 { status = "okay"; clock-rate=<50000000>; @@ -49,15 +69,23 @@ }; partition@10000 { label = "u-boot"; - reg = <0x10000 0x40000>; + reg = <0x10000 0x50000>; }; - partition@50000 { + partition@60000 { + label = "environment"; + reg = <0x60000 0x10000>; + }; + partition@70000 { + label = "dtb"; + reg = <0x70000 0x10000>; + }; + partition@80000 { label = "linux"; - reg = <0x50000 0x2c0000>; + reg = <0x80000 0x310000>; }; - partition@310000 { + partition@390000 { label = "rootfs"; - reg = <0x310000 0x4f0000>; + reg = <0x390000 0x0>; }; }; }; @@ -65,10 +93,18 @@ apb { serial@d0000000 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; }; serial@d0080000 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + }; + + rtc@fc900000 { + status = "okay"; }; i2c@d0200000 { diff --git a/arch/arm/boot/dts/spear600.dtsi b/arch/arm/boot/dts/spear600.dtsi index a3c36e47d7ef..e051dde5181f 100644 --- a/arch/arm/boot/dts/spear600.dtsi +++ b/arch/arm/boot/dts/spear600.dtsi @@ -45,6 +45,14 @@ #interrupt-cells = <1>; }; + clcd@fc200000 { + compatible = "arm,pl110", "arm,primecell"; + reg = <0xfc200000 0x1000>; + interrupt-parent = <&vic1>; + interrupts = <12>; + status = "disabled"; + }; + dma@fc400000 { compatible = "arm,pl080", "arm,primecell"; reg = <0xfc400000 0x1000>; @@ -59,6 +67,7 @@ interrupt-parent = <&vic1>; interrupts = <24 23>; interrupt-names = "macirq", "eth_wake_irq"; + phy-mode = "gmii"; status = "disabled"; }; @@ -178,6 +187,13 @@ status = "disabled"; }; + rtc@fc900000 { + compatible = "st,spear600-rtc"; + reg = <0xfc900000 0x1000>; + interrupts = <10>; + status = "disabled"; + }; + timer@f0000000 { compatible = "st,spear-timer"; reg = <0xf0000000 0x400>; diff --git a/arch/arm/mach-spear13xx/include/mach/spear.h b/arch/arm/mach-spear13xx/include/mach/spear.h index 07d90acc92c8..7cfa6818865a 100644 --- a/arch/arm/mach-spear13xx/include/mach/spear.h +++ b/arch/arm/mach-spear13xx/include/mach/spear.h @@ -47,14 +47,6 @@ #define DMAC1_BASE UL(0xEB000000) #define MCIF_CF_BASE UL(0xB2800000) -/* Devices present in SPEAr1310 */ -#ifdef CONFIG_MACH_SPEAR1310 -#define SPEAR1310_RAS_GRP1_BASE UL(0xD8000000) -#define VA_SPEAR1310_RAS_GRP1_BASE UL(0xFA000000) -#define SPEAR1310_RAS_BASE UL(0xD8400000) -#define VA_SPEAR1310_RAS_BASE IOMEM(UL(0xFA400000)) -#endif /* CONFIG_MACH_SPEAR1310 */ - /* Debug uart for linux, will be used for debug and uncompress messages */ #define SPEAR_DBG_UART_BASE UART_BASE #define VA_SPEAR_DBG_UART_BASE VA_UART_BASE diff --git a/arch/arm/mach-spear13xx/spear1310.c b/arch/arm/mach-spear13xx/spear1310.c index 9fbbfc5650aa..02f4724bb0d4 100644 --- a/arch/arm/mach-spear13xx/spear1310.c +++ b/arch/arm/mach-spear13xx/spear1310.c @@ -15,6 +15,7 @@ #include <linux/amba/pl022.h> #include <linux/of_platform.h> +#include <linux/pata_arasan_cf_data.h> #include <asm/hardware/gic.h> #include <asm/mach/arch.h> #include <asm/mach/map.h> @@ -27,16 +28,25 @@ #define SPEAR1310_SATA1_BASE UL(0xB1800000) #define SPEAR1310_SATA2_BASE UL(0xB4000000) +#define SPEAR1310_RAS_GRP1_BASE UL(0xD8000000) +#define VA_SPEAR1310_RAS_GRP1_BASE UL(0xFA000000) +#define SPEAR1310_RAS_BASE UL(0xD8400000) +#define VA_SPEAR1310_RAS_BASE IOMEM(UL(0xFA400000)) + +static struct arasan_cf_pdata cf_pdata = { + .cf_if_clk = CF_IF_CLK_166M, + .quirk = CF_BROKEN_UDMA, + .dma_priv = &cf_dma_priv, +}; + /* ssp device registration */ static struct pl022_ssp_controller ssp1_plat_data = { - .bus_id = 0, .enable_dma = 0, - .num_chipselect = 3, }; /* Add SPEAr1310 auxdata to pass platform data */ static struct of_dev_auxdata spear1310_auxdata_lookup[] __initdata = { - OF_DEV_AUXDATA("arasan,cf-spear1340", MCIF_CF_BASE, NULL, &cf_dma_priv), + OF_DEV_AUXDATA("arasan,cf-spear1340", MCIF_CF_BASE, NULL, &cf_pdata), OF_DEV_AUXDATA("snps,dma-spear1340", DMAC0_BASE, NULL, &dmac_plat_data), OF_DEV_AUXDATA("snps,dma-spear1340", DMAC1_BASE, NULL, &dmac_plat_data), OF_DEV_AUXDATA("arm,pl022", SSP_BASE, NULL, &pl022_plat_data), diff --git a/arch/arm/mach-spear13xx/spear13xx.c b/arch/arm/mach-spear13xx/spear13xx.c index 5633d698f1e1..c4af775a8451 100644 --- a/arch/arm/mach-spear13xx/spear13xx.c +++ b/arch/arm/mach-spear13xx/spear13xx.c @@ -57,12 +57,10 @@ static struct dw_dma_slave ssp_dma_param[] = { }; struct pl022_ssp_controller pl022_plat_data = { - .bus_id = 0, .enable_dma = 1, .dma_filter = dw_dma_filter, .dma_rx_param = &ssp_dma_param[1], .dma_tx_param = &ssp_dma_param[0], - .num_chipselect = 3, }; /* CF device registration */ diff --git a/arch/arm/mach-spear3xx/include/mach/irqs.h b/arch/arm/mach-spear3xx/include/mach/irqs.h index 803de76f5f36..f95e5b2b6686 100644 --- a/arch/arm/mach-spear3xx/include/mach/irqs.h +++ b/arch/arm/mach-spear3xx/include/mach/irqs.h @@ -14,14 +14,6 @@ #ifndef __MACH_IRQS_H #define __MACH_IRQS_H -/* FIXME: probe all these from DT */ -#define SPEAR3XX_IRQ_INTRCOMM_RAS_ARM 1 -#define SPEAR3XX_IRQ_GEN_RAS_1 28 -#define SPEAR3XX_IRQ_GEN_RAS_2 29 -#define SPEAR3XX_IRQ_GEN_RAS_3 30 -#define SPEAR3XX_IRQ_VIC_END 32 -#define SPEAR3XX_VIRQ_START SPEAR3XX_IRQ_VIC_END - -#define NR_IRQS 160 +#define NR_IRQS 256 #endif /* __MACH_IRQS_H */ diff --git a/arch/arm/mach-spear3xx/spear300.c b/arch/arm/mach-spear3xx/spear300.c index 6ec300549960..a69cbfdb07ee 100644 --- a/arch/arm/mach-spear3xx/spear300.c +++ b/arch/arm/mach-spear3xx/spear300.c @@ -17,102 +17,9 @@ #include <linux/of_platform.h> #include <asm/hardware/vic.h> #include <asm/mach/arch.h> -#include <plat/shirq.h> #include <mach/generic.h> #include <mach/spear.h> -/* Base address of various IPs */ -#define SPEAR300_TELECOM_BASE UL(0x50000000) - -/* Interrupt registers offsets and masks */ -#define SPEAR300_INT_ENB_MASK_REG 0x54 -#define SPEAR300_INT_STS_MASK_REG 0x58 -#define SPEAR300_IT_PERS_S_IRQ_MASK (1 << 0) -#define SPEAR300_IT_CHANGE_S_IRQ_MASK (1 << 1) -#define SPEAR300_I2S_IRQ_MASK (1 << 2) -#define SPEAR300_TDM_IRQ_MASK (1 << 3) -#define SPEAR300_CAMERA_L_IRQ_MASK (1 << 4) -#define SPEAR300_CAMERA_F_IRQ_MASK (1 << 5) -#define SPEAR300_CAMERA_V_IRQ_MASK (1 << 6) -#define SPEAR300_KEYBOARD_IRQ_MASK (1 << 7) -#define SPEAR300_GPIO1_IRQ_MASK (1 << 8) - -#define SPEAR300_SHIRQ_RAS1_MASK 0x1FF - -#define SPEAR300_SOC_CONFIG_BASE UL(0x99000000) - - -/* SPEAr300 Virtual irq definitions */ -/* IRQs sharing IRQ_GEN_RAS_1 */ -#define SPEAR300_VIRQ_IT_PERS_S (SPEAR3XX_VIRQ_START + 0) -#define SPEAR300_VIRQ_IT_CHANGE_S (SPEAR3XX_VIRQ_START + 1) -#define SPEAR300_VIRQ_I2S (SPEAR3XX_VIRQ_START + 2) -#define SPEAR300_VIRQ_TDM (SPEAR3XX_VIRQ_START + 3) -#define SPEAR300_VIRQ_CAMERA_L (SPEAR3XX_VIRQ_START + 4) -#define SPEAR300_VIRQ_CAMERA_F (SPEAR3XX_VIRQ_START + 5) -#define SPEAR300_VIRQ_CAMERA_V (SPEAR3XX_VIRQ_START + 6) -#define SPEAR300_VIRQ_KEYBOARD (SPEAR3XX_VIRQ_START + 7) -#define SPEAR300_VIRQ_GPIO1 (SPEAR3XX_VIRQ_START + 8) - -/* IRQs sharing IRQ_GEN_RAS_3 */ -#define SPEAR300_IRQ_CLCD SPEAR3XX_IRQ_GEN_RAS_3 - -/* IRQs sharing IRQ_INTRCOMM_RAS_ARM */ -#define SPEAR300_IRQ_SDHCI SPEAR3XX_IRQ_INTRCOMM_RAS_ARM - -/* spear3xx shared irq */ -static struct shirq_dev_config shirq_ras1_config[] = { - { - .virq = SPEAR300_VIRQ_IT_PERS_S, - .enb_mask = SPEAR300_IT_PERS_S_IRQ_MASK, - .status_mask = SPEAR300_IT_PERS_S_IRQ_MASK, - }, { - .virq = SPEAR300_VIRQ_IT_CHANGE_S, - .enb_mask = SPEAR300_IT_CHANGE_S_IRQ_MASK, - .status_mask = SPEAR300_IT_CHANGE_S_IRQ_MASK, - }, { - .virq = SPEAR300_VIRQ_I2S, - .enb_mask = SPEAR300_I2S_IRQ_MASK, - .status_mask = SPEAR300_I2S_IRQ_MASK, - }, { - .virq = SPEAR300_VIRQ_TDM, - .enb_mask = SPEAR300_TDM_IRQ_MASK, - .status_mask = SPEAR300_TDM_IRQ_MASK, - }, { - .virq = SPEAR300_VIRQ_CAMERA_L, - .enb_mask = SPEAR300_CAMERA_L_IRQ_MASK, - .status_mask = SPEAR300_CAMERA_L_IRQ_MASK, - }, { - .virq = SPEAR300_VIRQ_CAMERA_F, - .enb_mask = SPEAR300_CAMERA_F_IRQ_MASK, - .status_mask = SPEAR300_CAMERA_F_IRQ_MASK, - }, { - .virq = SPEAR300_VIRQ_CAMERA_V, - .enb_mask = SPEAR300_CAMERA_V_IRQ_MASK, - .status_mask = SPEAR300_CAMERA_V_IRQ_MASK, - }, { - .virq = SPEAR300_VIRQ_KEYBOARD, - .enb_mask = SPEAR300_KEYBOARD_IRQ_MASK, - .status_mask = SPEAR300_KEYBOARD_IRQ_MASK, - }, { - .virq = SPEAR300_VIRQ_GPIO1, - .enb_mask = SPEAR300_GPIO1_IRQ_MASK, - .status_mask = SPEAR300_GPIO1_IRQ_MASK, - }, -}; - -static struct spear_shirq shirq_ras1 = { - .irq = SPEAR3XX_IRQ_GEN_RAS_1, - .dev_config = shirq_ras1_config, - .dev_count = ARRAY_SIZE(shirq_ras1_config), - .regs = { - .enb_reg = SPEAR300_INT_ENB_MASK_REG, - .status_reg = SPEAR300_INT_STS_MASK_REG, - .status_reg_mask = SPEAR300_SHIRQ_RAS1_MASK, - .clear_reg = -1, - }, -}; - /* DMAC platform data's slave info */ struct pl08x_channel_data spear300_dma_info[] = { { @@ -285,21 +192,11 @@ static struct of_dev_auxdata spear300_auxdata_lookup[] __initdata = { static void __init spear300_dt_init(void) { - int ret; - pl080_plat_data.slave_channels = spear300_dma_info; pl080_plat_data.num_slave_channels = ARRAY_SIZE(spear300_dma_info); of_platform_populate(NULL, of_default_bus_match_table, spear300_auxdata_lookup, NULL); - - /* shared irq registration */ - shirq_ras1.regs.base = ioremap(SPEAR300_TELECOM_BASE, SZ_4K); - if (shirq_ras1.regs.base) { - ret = spear_shirq_register(&shirq_ras1); - if (ret) - pr_err("Error registering Shared IRQ\n"); - } } static const char * const spear300_dt_board_compat[] = { diff --git a/arch/arm/mach-spear3xx/spear310.c b/arch/arm/mach-spear3xx/spear310.c index 1d0e435b9045..b963ebb10b56 100644 --- a/arch/arm/mach-spear3xx/spear310.c +++ b/arch/arm/mach-spear3xx/spear310.c @@ -18,7 +18,6 @@ #include <linux/of_platform.h> #include <asm/hardware/vic.h> #include <asm/mach/arch.h> -#include <plat/shirq.h> #include <mach/generic.h> #include <mach/spear.h> @@ -27,176 +26,6 @@ #define SPEAR310_UART3_BASE UL(0xB2100000) #define SPEAR310_UART4_BASE UL(0xB2180000) #define SPEAR310_UART5_BASE UL(0xB2200000) -#define SPEAR310_SOC_CONFIG_BASE UL(0xB4000000) - -/* Interrupt registers offsets and masks */ -#define SPEAR310_INT_STS_MASK_REG 0x04 -#define SPEAR310_SMII0_IRQ_MASK (1 << 0) -#define SPEAR310_SMII1_IRQ_MASK (1 << 1) -#define SPEAR310_SMII2_IRQ_MASK (1 << 2) -#define SPEAR310_SMII3_IRQ_MASK (1 << 3) -#define SPEAR310_WAKEUP_SMII0_IRQ_MASK (1 << 4) -#define SPEAR310_WAKEUP_SMII1_IRQ_MASK (1 << 5) -#define SPEAR310_WAKEUP_SMII2_IRQ_MASK (1 << 6) -#define SPEAR310_WAKEUP_SMII3_IRQ_MASK (1 << 7) -#define SPEAR310_UART1_IRQ_MASK (1 << 8) -#define SPEAR310_UART2_IRQ_MASK (1 << 9) -#define SPEAR310_UART3_IRQ_MASK (1 << 10) -#define SPEAR310_UART4_IRQ_MASK (1 << 11) -#define SPEAR310_UART5_IRQ_MASK (1 << 12) -#define SPEAR310_EMI_IRQ_MASK (1 << 13) -#define SPEAR310_TDM_HDLC_IRQ_MASK (1 << 14) -#define SPEAR310_RS485_0_IRQ_MASK (1 << 15) -#define SPEAR310_RS485_1_IRQ_MASK (1 << 16) - -#define SPEAR310_SHIRQ_RAS1_MASK 0x000FF -#define SPEAR310_SHIRQ_RAS2_MASK 0x01F00 -#define SPEAR310_SHIRQ_RAS3_MASK 0x02000 -#define SPEAR310_SHIRQ_INTRCOMM_RAS_MASK 0x1C000 - -/* SPEAr310 Virtual irq definitions */ -/* IRQs sharing IRQ_GEN_RAS_1 */ -#define SPEAR310_VIRQ_SMII0 (SPEAR3XX_VIRQ_START + 0) -#define SPEAR310_VIRQ_SMII1 (SPEAR3XX_VIRQ_START + 1) -#define SPEAR310_VIRQ_SMII2 (SPEAR3XX_VIRQ_START + 2) -#define SPEAR310_VIRQ_SMII3 (SPEAR3XX_VIRQ_START + 3) -#define SPEAR310_VIRQ_WAKEUP_SMII0 (SPEAR3XX_VIRQ_START + 4) -#define SPEAR310_VIRQ_WAKEUP_SMII1 (SPEAR3XX_VIRQ_START + 5) -#define SPEAR310_VIRQ_WAKEUP_SMII2 (SPEAR3XX_VIRQ_START + 6) -#define SPEAR310_VIRQ_WAKEUP_SMII3 (SPEAR3XX_VIRQ_START + 7) - -/* IRQs sharing IRQ_GEN_RAS_2 */ -#define SPEAR310_VIRQ_UART1 (SPEAR3XX_VIRQ_START + 8) -#define SPEAR310_VIRQ_UART2 (SPEAR3XX_VIRQ_START + 9) -#define SPEAR310_VIRQ_UART3 (SPEAR3XX_VIRQ_START + 10) -#define SPEAR310_VIRQ_UART4 (SPEAR3XX_VIRQ_START + 11) -#define SPEAR310_VIRQ_UART5 (SPEAR3XX_VIRQ_START + 12) - -/* IRQs sharing IRQ_GEN_RAS_3 */ -#define SPEAR310_VIRQ_EMI (SPEAR3XX_VIRQ_START + 13) -#define SPEAR310_VIRQ_PLGPIO (SPEAR3XX_VIRQ_START + 14) - -/* IRQs sharing IRQ_INTRCOMM_RAS_ARM */ -#define SPEAR310_VIRQ_TDM_HDLC (SPEAR3XX_VIRQ_START + 15) -#define SPEAR310_VIRQ_RS485_0 (SPEAR3XX_VIRQ_START + 16) -#define SPEAR310_VIRQ_RS485_1 (SPEAR3XX_VIRQ_START + 17) - - -/* spear3xx shared irq */ -static struct shirq_dev_config shirq_ras1_config[] = { - { - .virq = SPEAR310_VIRQ_SMII0, - .status_mask = SPEAR310_SMII0_IRQ_MASK, - }, { - .virq = SPEAR310_VIRQ_SMII1, - .status_mask = SPEAR310_SMII1_IRQ_MASK, - }, { - .virq = SPEAR310_VIRQ_SMII2, - .status_mask = SPEAR310_SMII2_IRQ_MASK, - }, { - .virq = SPEAR310_VIRQ_SMII3, - .status_mask = SPEAR310_SMII3_IRQ_MASK, - }, { - .virq = SPEAR310_VIRQ_WAKEUP_SMII0, - .status_mask = SPEAR310_WAKEUP_SMII0_IRQ_MASK, - }, { - .virq = SPEAR310_VIRQ_WAKEUP_SMII1, - .status_mask = SPEAR310_WAKEUP_SMII1_IRQ_MASK, - }, { - .virq = SPEAR310_VIRQ_WAKEUP_SMII2, - .status_mask = SPEAR310_WAKEUP_SMII2_IRQ_MASK, - }, { - .virq = SPEAR310_VIRQ_WAKEUP_SMII3, - .status_mask = SPEAR310_WAKEUP_SMII3_IRQ_MASK, - }, -}; - -static struct spear_shirq shirq_ras1 = { - .irq = SPEAR3XX_IRQ_GEN_RAS_1, - .dev_config = shirq_ras1_config, - .dev_count = ARRAY_SIZE(shirq_ras1_config), - .regs = { - .enb_reg = -1, - .status_reg = SPEAR310_INT_STS_MASK_REG, - .status_reg_mask = SPEAR310_SHIRQ_RAS1_MASK, - .clear_reg = -1, - }, -}; - -static struct shirq_dev_config shirq_ras2_config[] = { - { - .virq = SPEAR310_VIRQ_UART1, - .status_mask = SPEAR310_UART1_IRQ_MASK, - }, { - .virq = SPEAR310_VIRQ_UART2, - .status_mask = SPEAR310_UART2_IRQ_MASK, - }, { - .virq = SPEAR310_VIRQ_UART3, - .status_mask = SPEAR310_UART3_IRQ_MASK, - }, { - .virq = SPEAR310_VIRQ_UART4, - .status_mask = SPEAR310_UART4_IRQ_MASK, - }, { - .virq = SPEAR310_VIRQ_UART5, - .status_mask = SPEAR310_UART5_IRQ_MASK, - }, -}; - -static struct spear_shirq shirq_ras2 = { - .irq = SPEAR3XX_IRQ_GEN_RAS_2, - .dev_config = shirq_ras2_config, - .dev_count = ARRAY_SIZE(shirq_ras2_config), - .regs = { - .enb_reg = -1, - .status_reg = SPEAR310_INT_STS_MASK_REG, - .status_reg_mask = SPEAR310_SHIRQ_RAS2_MASK, - .clear_reg = -1, - }, -}; - -static struct shirq_dev_config shirq_ras3_config[] = { - { - .virq = SPEAR310_VIRQ_EMI, - .status_mask = SPEAR310_EMI_IRQ_MASK, - }, -}; - -static struct spear_shirq shirq_ras3 = { - .irq = SPEAR3XX_IRQ_GEN_RAS_3, - .dev_config = shirq_ras3_config, - .dev_count = ARRAY_SIZE(shirq_ras3_config), - .regs = { - .enb_reg = -1, - .status_reg = SPEAR310_INT_STS_MASK_REG, - .status_reg_mask = SPEAR310_SHIRQ_RAS3_MASK, - .clear_reg = -1, - }, -}; - -static struct shirq_dev_config shirq_intrcomm_ras_config[] = { - { - .virq = SPEAR310_VIRQ_TDM_HDLC, - .status_mask = SPEAR310_TDM_HDLC_IRQ_MASK, - }, { - .virq = SPEAR310_VIRQ_RS485_0, - .status_mask = SPEAR310_RS485_0_IRQ_MASK, - }, { - .virq = SPEAR310_VIRQ_RS485_1, - .status_mask = SPEAR310_RS485_1_IRQ_MASK, - }, -}; - -static struct spear_shirq shirq_intrcomm_ras = { - .irq = SPEAR3XX_IRQ_INTRCOMM_RAS_ARM, - .dev_config = shirq_intrcomm_ras_config, - .dev_count = ARRAY_SIZE(shirq_intrcomm_ras_config), - .regs = { - .enb_reg = -1, - .status_reg = SPEAR310_INT_STS_MASK_REG, - .status_reg_mask = SPEAR310_SHIRQ_INTRCOMM_RAS_MASK, - .clear_reg = -1, - }, -}; /* DMAC platform data's slave info */ struct pl08x_channel_data spear310_dma_info[] = { @@ -405,42 +234,11 @@ static struct of_dev_auxdata spear310_auxdata_lookup[] __initdata = { static void __init spear310_dt_init(void) { - void __iomem *base; - int ret; - pl080_plat_data.slave_channels = spear310_dma_info; pl080_plat_data.num_slave_channels = ARRAY_SIZE(spear310_dma_info); of_platform_populate(NULL, of_default_bus_match_table, spear310_auxdata_lookup, NULL); - - /* shared irq registration */ - base = ioremap(SPEAR310_SOC_CONFIG_BASE, SZ_4K); - if (base) { - /* shirq 1 */ - shirq_ras1.regs.base = base; - ret = spear_shirq_register(&shirq_ras1); - if (ret) - pr_err("Error registering Shared IRQ 1\n"); - - /* shirq 2 */ - shirq_ras2.regs.base = base; - ret = spear_shirq_register(&shirq_ras2); - if (ret) - pr_err("Error registering Shared IRQ 2\n"); - - /* shirq 3 */ - shirq_ras3.regs.base = base; - ret = spear_shirq_register(&shirq_ras3); - if (ret) - pr_err("Error registering Shared IRQ 3\n"); - - /* shirq 4 */ - shirq_intrcomm_ras.regs.base = base; - ret = spear_shirq_register(&shirq_intrcomm_ras); - if (ret) - pr_err("Error registering Shared IRQ 4\n"); - } } static const char * const spear310_dt_board_compat[] = { diff --git a/arch/arm/mach-spear3xx/spear320.c b/arch/arm/mach-spear3xx/spear320.c index fd823c624575..66e3a0c33e75 100644 --- a/arch/arm/mach-spear3xx/spear320.c +++ b/arch/arm/mach-spear3xx/spear320.c @@ -19,7 +19,6 @@ #include <linux/of_platform.h> #include <asm/hardware/vic.h> #include <asm/mach/arch.h> -#include <plat/shirq.h> #include <mach/generic.h> #include <mach/spear.h> @@ -28,184 +27,6 @@ #define SPEAR320_SSP0_BASE UL(0xA5000000) #define SPEAR320_SSP1_BASE UL(0xA6000000) -/* Interrupt registers offsets and masks */ -#define SPEAR320_INT_STS_MASK_REG 0x04 -#define SPEAR320_INT_CLR_MASK_REG 0x04 -#define SPEAR320_INT_ENB_MASK_REG 0x08 -#define SPEAR320_GPIO_IRQ_MASK (1 << 0) -#define SPEAR320_I2S_PLAY_IRQ_MASK (1 << 1) -#define SPEAR320_I2S_REC_IRQ_MASK (1 << 2) -#define SPEAR320_EMI_IRQ_MASK (1 << 7) -#define SPEAR320_CLCD_IRQ_MASK (1 << 8) -#define SPEAR320_SPP_IRQ_MASK (1 << 9) -#define SPEAR320_SDHCI_IRQ_MASK (1 << 10) -#define SPEAR320_CAN_U_IRQ_MASK (1 << 11) -#define SPEAR320_CAN_L_IRQ_MASK (1 << 12) -#define SPEAR320_UART1_IRQ_MASK (1 << 13) -#define SPEAR320_UART2_IRQ_MASK (1 << 14) -#define SPEAR320_SSP1_IRQ_MASK (1 << 15) -#define SPEAR320_SSP2_IRQ_MASK (1 << 16) -#define SPEAR320_SMII0_IRQ_MASK (1 << 17) -#define SPEAR320_MII1_SMII1_IRQ_MASK (1 << 18) -#define SPEAR320_WAKEUP_SMII0_IRQ_MASK (1 << 19) -#define SPEAR320_WAKEUP_MII1_SMII1_IRQ_MASK (1 << 20) -#define SPEAR320_I2C1_IRQ_MASK (1 << 21) - -#define SPEAR320_SHIRQ_RAS1_MASK 0x000380 -#define SPEAR320_SHIRQ_RAS3_MASK 0x000007 -#define SPEAR320_SHIRQ_INTRCOMM_RAS_MASK 0x3FF800 - -/* SPEAr320 Virtual irq definitions */ -/* IRQs sharing IRQ_GEN_RAS_1 */ -#define SPEAR320_VIRQ_EMI (SPEAR3XX_VIRQ_START + 0) -#define SPEAR320_VIRQ_CLCD (SPEAR3XX_VIRQ_START + 1) -#define SPEAR320_VIRQ_SPP (SPEAR3XX_VIRQ_START + 2) - -/* IRQs sharing IRQ_GEN_RAS_2 */ -#define SPEAR320_IRQ_SDHCI SPEAR3XX_IRQ_GEN_RAS_2 - -/* IRQs sharing IRQ_GEN_RAS_3 */ -#define SPEAR320_VIRQ_PLGPIO (SPEAR3XX_VIRQ_START + 3) -#define SPEAR320_VIRQ_I2S_PLAY (SPEAR3XX_VIRQ_START + 4) -#define SPEAR320_VIRQ_I2S_REC (SPEAR3XX_VIRQ_START + 5) - -/* IRQs sharing IRQ_INTRCOMM_RAS_ARM */ -#define SPEAR320_VIRQ_CANU (SPEAR3XX_VIRQ_START + 6) -#define SPEAR320_VIRQ_CANL (SPEAR3XX_VIRQ_START + 7) -#define SPEAR320_VIRQ_UART1 (SPEAR3XX_VIRQ_START + 8) -#define SPEAR320_VIRQ_UART2 (SPEAR3XX_VIRQ_START + 9) -#define SPEAR320_VIRQ_SSP1 (SPEAR3XX_VIRQ_START + 10) -#define SPEAR320_VIRQ_SSP2 (SPEAR3XX_VIRQ_START + 11) -#define SPEAR320_VIRQ_SMII0 (SPEAR3XX_VIRQ_START + 12) -#define SPEAR320_VIRQ_MII1_SMII1 (SPEAR3XX_VIRQ_START + 13) -#define SPEAR320_VIRQ_WAKEUP_SMII0 (SPEAR3XX_VIRQ_START + 14) -#define SPEAR320_VIRQ_WAKEUP_MII1_SMII1 (SPEAR3XX_VIRQ_START + 15) -#define SPEAR320_VIRQ_I2C1 (SPEAR3XX_VIRQ_START + 16) - -/* spear3xx shared irq */ -static struct shirq_dev_config shirq_ras1_config[] = { - { - .virq = SPEAR320_VIRQ_EMI, - .status_mask = SPEAR320_EMI_IRQ_MASK, - .clear_mask = SPEAR320_EMI_IRQ_MASK, - }, { - .virq = SPEAR320_VIRQ_CLCD, - .status_mask = SPEAR320_CLCD_IRQ_MASK, - .clear_mask = SPEAR320_CLCD_IRQ_MASK, - }, { - .virq = SPEAR320_VIRQ_SPP, - .status_mask = SPEAR320_SPP_IRQ_MASK, - .clear_mask = SPEAR320_SPP_IRQ_MASK, - }, -}; - -static struct spear_shirq shirq_ras1 = { - .irq = SPEAR3XX_IRQ_GEN_RAS_1, - .dev_config = shirq_ras1_config, - .dev_count = ARRAY_SIZE(shirq_ras1_config), - .regs = { - .enb_reg = -1, - .status_reg = SPEAR320_INT_STS_MASK_REG, - .status_reg_mask = SPEAR320_SHIRQ_RAS1_MASK, - .clear_reg = SPEAR320_INT_CLR_MASK_REG, - .reset_to_clear = 1, - }, -}; - -static struct shirq_dev_config shirq_ras3_config[] = { - { - .virq = SPEAR320_VIRQ_PLGPIO, - .enb_mask = SPEAR320_GPIO_IRQ_MASK, - .status_mask = SPEAR320_GPIO_IRQ_MASK, - .clear_mask = SPEAR320_GPIO_IRQ_MASK, - }, { - .virq = SPEAR320_VIRQ_I2S_PLAY, - .enb_mask = SPEAR320_I2S_PLAY_IRQ_MASK, - .status_mask = SPEAR320_I2S_PLAY_IRQ_MASK, - .clear_mask = SPEAR320_I2S_PLAY_IRQ_MASK, - }, { - .virq = SPEAR320_VIRQ_I2S_REC, - .enb_mask = SPEAR320_I2S_REC_IRQ_MASK, - .status_mask = SPEAR320_I2S_REC_IRQ_MASK, - .clear_mask = SPEAR320_I2S_REC_IRQ_MASK, - }, -}; - -static struct spear_shirq shirq_ras3 = { - .irq = SPEAR3XX_IRQ_GEN_RAS_3, - .dev_config = shirq_ras3_config, - .dev_count = ARRAY_SIZE(shirq_ras3_config), - .regs = { - .enb_reg = SPEAR320_INT_ENB_MASK_REG, - .reset_to_enb = 1, - .status_reg = SPEAR320_INT_STS_MASK_REG, - .status_reg_mask = SPEAR320_SHIRQ_RAS3_MASK, - .clear_reg = SPEAR320_INT_CLR_MASK_REG, - .reset_to_clear = 1, - }, -}; - -static struct shirq_dev_config shirq_intrcomm_ras_config[] = { - { - .virq = SPEAR320_VIRQ_CANU, - .status_mask = SPEAR320_CAN_U_IRQ_MASK, - .clear_mask = SPEAR320_CAN_U_IRQ_MASK, - }, { - .virq = SPEAR320_VIRQ_CANL, - .status_mask = SPEAR320_CAN_L_IRQ_MASK, - .clear_mask = SPEAR320_CAN_L_IRQ_MASK, - }, { - .virq = SPEAR320_VIRQ_UART1, - .status_mask = SPEAR320_UART1_IRQ_MASK, - .clear_mask = SPEAR320_UART1_IRQ_MASK, - }, { - .virq = SPEAR320_VIRQ_UART2, - .status_mask = SPEAR320_UART2_IRQ_MASK, - .clear_mask = SPEAR320_UART2_IRQ_MASK, - }, { - .virq = SPEAR320_VIRQ_SSP1, - .status_mask = SPEAR320_SSP1_IRQ_MASK, - .clear_mask = SPEAR320_SSP1_IRQ_MASK, - }, { - .virq = SPEAR320_VIRQ_SSP2, - .status_mask = SPEAR320_SSP2_IRQ_MASK, - .clear_mask = SPEAR320_SSP2_IRQ_MASK, - }, { - .virq = SPEAR320_VIRQ_SMII0, - .status_mask = SPEAR320_SMII0_IRQ_MASK, - .clear_mask = SPEAR320_SMII0_IRQ_MASK, - }, { - .virq = SPEAR320_VIRQ_MII1_SMII1, - .status_mask = SPEAR320_MII1_SMII1_IRQ_MASK, - .clear_mask = SPEAR320_MII1_SMII1_IRQ_MASK, - }, { - .virq = SPEAR320_VIRQ_WAKEUP_SMII0, - .status_mask = SPEAR320_WAKEUP_SMII0_IRQ_MASK, - .clear_mask = SPEAR320_WAKEUP_SMII0_IRQ_MASK, - }, { - .virq = SPEAR320_VIRQ_WAKEUP_MII1_SMII1, - .status_mask = SPEAR320_WAKEUP_MII1_SMII1_IRQ_MASK, - .clear_mask = SPEAR320_WAKEUP_MII1_SMII1_IRQ_MASK, - }, { - .virq = SPEAR320_VIRQ_I2C1, - .status_mask = SPEAR320_I2C1_IRQ_MASK, - .clear_mask = SPEAR320_I2C1_IRQ_MASK, - }, -}; - -static struct spear_shirq shirq_intrcomm_ras = { - .irq = SPEAR3XX_IRQ_INTRCOMM_RAS_ARM, - .dev_config = shirq_intrcomm_ras_config, - .dev_count = ARRAY_SIZE(shirq_intrcomm_ras_config), - .regs = { - .enb_reg = -1, - .status_reg = SPEAR320_INT_STS_MASK_REG, - .status_reg_mask = SPEAR320_SHIRQ_INTRCOMM_RAS_MASK, - .clear_reg = SPEAR320_INT_CLR_MASK_REG, - .reset_to_clear = 1, - }, -}; - /* DMAC platform data's slave info */ struct pl08x_channel_data spear320_dma_info[] = { { @@ -416,41 +237,17 @@ static struct of_dev_auxdata spear320_auxdata_lookup[] __initdata = { static void __init spear320_dt_init(void) { - void __iomem *base; - int ret; - pl080_plat_data.slave_channels = spear320_dma_info; pl080_plat_data.num_slave_channels = ARRAY_SIZE(spear320_dma_info); of_platform_populate(NULL, of_default_bus_match_table, spear320_auxdata_lookup, NULL); - - /* shared irq registration */ - base = ioremap(SPEAR320_SOC_CONFIG_BASE, SZ_4K); - if (base) { - /* shirq 1 */ - shirq_ras1.regs.base = base; - ret = spear_shirq_register(&shirq_ras1); - if (ret) - pr_err("Error registering Shared IRQ 1\n"); - - /* shirq 3 */ - shirq_ras3.regs.base = base; - ret = spear_shirq_register(&shirq_ras3); - if (ret) - pr_err("Error registering Shared IRQ 3\n"); - - /* shirq 4 */ - shirq_intrcomm_ras.regs.base = base; - ret = spear_shirq_register(&shirq_intrcomm_ras); - if (ret) - pr_err("Error registering Shared IRQ 4\n"); - } } static const char * const spear320_dt_board_compat[] = { "st,spear320", "st,spear320-evb", + "st,spear320-hmi", NULL, }; diff --git a/arch/arm/mach-spear3xx/spear3xx.c b/arch/arm/mach-spear3xx/spear3xx.c index 98144baf8883..38fe95db31a7 100644 --- a/arch/arm/mach-spear3xx/spear3xx.c +++ b/arch/arm/mach-spear3xx/spear3xx.c @@ -15,6 +15,7 @@ #include <linux/amba/pl022.h> #include <linux/amba/pl08x.h> +#include <linux/irqchip/spear-shirq.h> #include <linux/of_irq.h> #include <linux/io.h> #include <asm/hardware/pl080.h> @@ -121,6 +122,9 @@ struct sys_timer spear3xx_timer = { static const struct of_device_id vic_of_match[] __initconst = { { .compatible = "arm,pl190-vic", .data = vic_of_init, }, + { .compatible = "st,spear300-shirq", .data = spear300_shirq_of_init, }, + { .compatible = "st,spear310-shirq", .data = spear310_shirq_of_init, }, + { .compatible = "st,spear320-shirq", .data = spear320_shirq_of_init, }, { /* Sentinel */ } }; diff --git a/arch/arm/plat-spear/Makefile b/arch/arm/plat-spear/Makefile index 2607bd05c525..01e88532a5db 100644 --- a/arch/arm/plat-spear/Makefile +++ b/arch/arm/plat-spear/Makefile @@ -5,5 +5,5 @@ # Common support obj-y := restart.o time.o -obj-$(CONFIG_ARCH_SPEAR3XX) += pl080.o shirq.o +obj-$(CONFIG_ARCH_SPEAR3XX) += pl080.o obj-$(CONFIG_ARCH_SPEAR6XX) += pl080.o diff --git a/arch/arm/plat-spear/shirq.c b/arch/arm/plat-spear/shirq.c deleted file mode 100644 index 853e891e1184..000000000000 --- a/arch/arm/plat-spear/shirq.c +++ /dev/null @@ -1,118 +0,0 @@ -/* - * arch/arm/plat-spear/shirq.c - * - * SPEAr platform shared irq layer source file - * - * Copyright (C) 2009 ST Microelectronics - * Viresh Kumar <viresh.linux@gmail.com> - * - * This file is licensed under the terms of the GNU General Public - * License version 2. This program is licensed "as is" without any - * warranty of any kind, whether express or implied. - */ - -#include <linux/err.h> -#include <linux/io.h> -#include <linux/irq.h> -#include <linux/spinlock.h> -#include <plat/shirq.h> - -struct spear_shirq *shirq; -static DEFINE_SPINLOCK(lock); - -static void shirq_irq_mask(struct irq_data *d) -{ - struct spear_shirq *shirq = irq_data_get_irq_chip_data(d); - u32 val, id = d->irq - shirq->dev_config[0].virq; - unsigned long flags; - - if ((shirq->regs.enb_reg == -1) || shirq->dev_config[id].enb_mask == -1) - return; - - spin_lock_irqsave(&lock, flags); - val = readl(shirq->regs.base + shirq->regs.enb_reg); - if (shirq->regs.reset_to_enb) - val |= shirq->dev_config[id].enb_mask; - else - val &= ~(shirq->dev_config[id].enb_mask); - writel(val, shirq->regs.base + shirq->regs.enb_reg); - spin_unlock_irqrestore(&lock, flags); -} - -static void shirq_irq_unmask(struct irq_data *d) -{ - struct spear_shirq *shirq = irq_data_get_irq_chip_data(d); - u32 val, id = d->irq - shirq->dev_config[0].virq; - unsigned long flags; - - if ((shirq->regs.enb_reg == -1) || shirq->dev_config[id].enb_mask == -1) - return; - - spin_lock_irqsave(&lock, flags); - val = readl(shirq->regs.base + shirq->regs.enb_reg); - if (shirq->regs.reset_to_enb) - val &= ~(shirq->dev_config[id].enb_mask); - else - val |= shirq->dev_config[id].enb_mask; - writel(val, shirq->regs.base + shirq->regs.enb_reg); - spin_unlock_irqrestore(&lock, flags); -} - -static struct irq_chip shirq_chip = { - .name = "spear_shirq", - .irq_ack = shirq_irq_mask, - .irq_mask = shirq_irq_mask, - .irq_unmask = shirq_irq_unmask, -}; - -static void shirq_handler(unsigned irq, struct irq_desc *desc) -{ - u32 i, val, mask; - struct spear_shirq *shirq = irq_get_handler_data(irq); - - desc->irq_data.chip->irq_ack(&desc->irq_data); - while ((val = readl(shirq->regs.base + shirq->regs.status_reg) & - shirq->regs.status_reg_mask)) { - for (i = 0; (i < shirq->dev_count) && val; i++) { - if (!(shirq->dev_config[i].status_mask & val)) - continue; - - generic_handle_irq(shirq->dev_config[i].virq); - - /* clear interrupt */ - val &= ~shirq->dev_config[i].status_mask; - if ((shirq->regs.clear_reg == -1) || - shirq->dev_config[i].clear_mask == -1) - continue; - mask = readl(shirq->regs.base + shirq->regs.clear_reg); - if (shirq->regs.reset_to_clear) - mask &= ~shirq->dev_config[i].clear_mask; - else - mask |= shirq->dev_config[i].clear_mask; - writel(mask, shirq->regs.base + shirq->regs.clear_reg); - } - } - desc->irq_data.chip->irq_unmask(&desc->irq_data); -} - -int spear_shirq_register(struct spear_shirq *shirq) -{ - int i; - - if (!shirq || !shirq->dev_config || !shirq->regs.base) - return -EFAULT; - - if (!shirq->dev_count) - return -EINVAL; - - irq_set_chained_handler(shirq->irq, shirq_handler); - for (i = 0; i < shirq->dev_count; i++) { - irq_set_chip_and_handler(shirq->dev_config[i].virq, - &shirq_chip, handle_simple_irq); - set_irq_flags(shirq->dev_config[i].virq, IRQF_VALID); - irq_set_chip_data(shirq->dev_config[i].virq, shirq); - } - - irq_set_handler_data(shirq->irq, shirq); - return 0; -} diff --git a/drivers/clk/spear/spear1310_clock.c b/drivers/clk/spear/spear1310_clock.c index 147e25f00405..ed9af4278619 100644 --- a/drivers/clk/spear/spear1310_clock.c +++ b/drivers/clk/spear/spear1310_clock.c @@ -20,6 +20,7 @@ #include <mach/spear.h> #include "clk.h" +#define VA_SPEAR1310_RAS_BASE IOMEM(UL(0xFA400000)) /* PLL related registers and bit values */ #define SPEAR1310_PLL_CFG (VA_MISC_BASE + 0x210) /* PLL_CFG bit values */ diff --git a/drivers/irqchip/Makefile b/drivers/irqchip/Makefile index 02bd37a6187f..bf4609a5bd9d 100644 --- a/drivers/irqchip/Makefile +++ b/drivers/irqchip/Makefile @@ -1,3 +1,4 @@ -obj-$(CONFIG_ARCH_BCM2835) += irq-bcm2835.o -obj-$(CONFIG_ARCH_SUNXI) += irq-sunxi.o -obj-$(CONFIG_VERSATILE_FPGA_IRQ) += irq-versatile-fpga.o +obj-$(CONFIG_ARCH_BCM2835) += irq-bcm2835.o +obj-$(CONFIG_ARCH_SUNXI) += irq-sunxi.o +obj-$(CONFIG_VERSATILE_FPGA_IRQ) += irq-versatile-fpga.o +obj-$(CONFIG_ARCH_SPEAR3XX) += spear-shirq.o diff --git a/drivers/irqchip/spear-shirq.c b/drivers/irqchip/spear-shirq.c new file mode 100644 index 000000000000..80e1d2fd9d4c --- /dev/null +++ b/drivers/irqchip/spear-shirq.c @@ -0,0 +1,316 @@ +/* + * SPEAr platform shared irq layer source file + * + * Copyright (C) 2009-2012 ST Microelectronics + * Viresh Kumar <viresh.linux@gmail.com> + * + * Copyright (C) 2012 ST Microelectronics + * Shiraz Hashim <shiraz.hashim@st.com> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + +#include <linux/err.h> +#include <linux/export.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/irq.h> +#include <linux/irqdomain.h> +#include <linux/irqchip/spear-shirq.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_irq.h> +#include <linux/spinlock.h> + +static DEFINE_SPINLOCK(lock); + +/* spear300 shared irq registers offsets and masks */ +#define SPEAR300_INT_ENB_MASK_REG 0x54 +#define SPEAR300_INT_STS_MASK_REG 0x58 + +static struct spear_shirq spear300_shirq_ras1 = { + .irq_nr = 9, + .irq_bit_off = 0, + .regs = { + .enb_reg = SPEAR300_INT_ENB_MASK_REG, + .status_reg = SPEAR300_INT_STS_MASK_REG, + .clear_reg = -1, + }, +}; + +static struct spear_shirq *spear300_shirq_blocks[] = { + &spear300_shirq_ras1, +}; + +/* spear310 shared irq registers offsets and masks */ +#define SPEAR310_INT_STS_MASK_REG 0x04 + +static struct spear_shirq spear310_shirq_ras1 = { + .irq_nr = 8, + .irq_bit_off = 0, + .regs = { + .enb_reg = -1, + .status_reg = SPEAR310_INT_STS_MASK_REG, + .clear_reg = -1, + }, +}; + +static struct spear_shirq spear310_shirq_ras2 = { + .irq_nr = 5, + .irq_bit_off = 8, + .regs = { + .enb_reg = -1, + .status_reg = SPEAR310_INT_STS_MASK_REG, + .clear_reg = -1, + }, +}; + +static struct spear_shirq spear310_shirq_ras3 = { + .irq_nr = 1, + .irq_bit_off = 13, + .regs = { + .enb_reg = -1, + .status_reg = SPEAR310_INT_STS_MASK_REG, + .clear_reg = -1, + }, +}; + +static struct spear_shirq spear310_shirq_intrcomm_ras = { + .irq_nr = 3, + .irq_bit_off = 14, + .regs = { + .enb_reg = -1, + .status_reg = SPEAR310_INT_STS_MASK_REG, + .clear_reg = -1, + }, +}; + +static struct spear_shirq *spear310_shirq_blocks[] = { + &spear310_shirq_ras1, + &spear310_shirq_ras2, + &spear310_shirq_ras3, + &spear310_shirq_intrcomm_ras, +}; + +/* spear320 shared irq registers offsets and masks */ +#define SPEAR320_INT_STS_MASK_REG 0x04 +#define SPEAR320_INT_CLR_MASK_REG 0x04 +#define SPEAR320_INT_ENB_MASK_REG 0x08 + +static struct spear_shirq spear320_shirq_ras1 = { + .irq_nr = 3, + .irq_bit_off = 7, + .regs = { + .enb_reg = -1, + .status_reg = SPEAR320_INT_STS_MASK_REG, + .clear_reg = SPEAR320_INT_CLR_MASK_REG, + .reset_to_clear = 1, + }, +}; + +static struct spear_shirq spear320_shirq_ras2 = { + .irq_nr = 1, + .irq_bit_off = 10, + .regs = { + .enb_reg = -1, + .status_reg = SPEAR320_INT_STS_MASK_REG, + .clear_reg = SPEAR320_INT_CLR_MASK_REG, + .reset_to_clear = 1, + }, +}; + +static struct spear_shirq spear320_shirq_ras3 = { + .irq_nr = 3, + .irq_bit_off = 0, + .invalid_irq = 1, + .regs = { + .enb_reg = SPEAR320_INT_ENB_MASK_REG, + .reset_to_enb = 1, + .status_reg = SPEAR320_INT_STS_MASK_REG, + .clear_reg = SPEAR320_INT_CLR_MASK_REG, + .reset_to_clear = 1, + }, +}; + +static struct spear_shirq spear320_shirq_intrcomm_ras = { + .irq_nr = 11, + .irq_bit_off = 11, + .regs = { + .enb_reg = -1, + .status_reg = SPEAR320_INT_STS_MASK_REG, + .clear_reg = SPEAR320_INT_CLR_MASK_REG, + .reset_to_clear = 1, + }, +}; + +static struct spear_shirq *spear320_shirq_blocks[] = { + &spear320_shirq_ras3, + &spear320_shirq_ras1, + &spear320_shirq_ras2, + &spear320_shirq_intrcomm_ras, +}; + +static void shirq_irq_mask_unmask(struct irq_data *d, bool mask) +{ + struct spear_shirq *shirq = irq_data_get_irq_chip_data(d); + u32 val, offset = d->irq - shirq->irq_base; + unsigned long flags; + + if (shirq->regs.enb_reg == -1) + return; + + spin_lock_irqsave(&lock, flags); + val = readl(shirq->base + shirq->regs.enb_reg); + + if (mask ^ shirq->regs.reset_to_enb) + val &= ~(0x1 << shirq->irq_bit_off << offset); + else + val |= 0x1 << shirq->irq_bit_off << offset; + + writel(val, shirq->base + shirq->regs.enb_reg); + spin_unlock_irqrestore(&lock, flags); + +} + +static void shirq_irq_mask(struct irq_data *d) +{ + shirq_irq_mask_unmask(d, 1); +} + +static void shirq_irq_unmask(struct irq_data *d) +{ + shirq_irq_mask_unmask(d, 0); +} + +static struct irq_chip shirq_chip = { + .name = "spear-shirq", + .irq_ack = shirq_irq_mask, + .irq_mask = shirq_irq_mask, + .irq_unmask = shirq_irq_unmask, +}; + +static void shirq_handler(unsigned irq, struct irq_desc *desc) +{ + u32 i, j, val, mask, tmp; + struct irq_chip *chip; + struct spear_shirq *shirq = irq_get_handler_data(irq); + + chip = irq_get_chip(irq); + chip->irq_ack(&desc->irq_data); + + mask = ((0x1 << shirq->irq_nr) - 1) << shirq->irq_bit_off; + while ((val = readl(shirq->base + shirq->regs.status_reg) & + mask)) { + + val >>= shirq->irq_bit_off; + for (i = 0, j = 1; i < shirq->irq_nr; i++, j <<= 1) { + + if (!(j & val)) + continue; + + generic_handle_irq(shirq->irq_base + i); + + /* clear interrupt */ + if (shirq->regs.clear_reg == -1) + continue; + + tmp = readl(shirq->base + shirq->regs.clear_reg); + if (shirq->regs.reset_to_clear) + tmp &= ~(j << shirq->irq_bit_off); + else + tmp |= (j << shirq->irq_bit_off); + writel(tmp, shirq->base + shirq->regs.clear_reg); + } + } + chip->irq_unmask(&desc->irq_data); +} + +static void __init spear_shirq_register(struct spear_shirq *shirq) +{ + int i; + + if (shirq->invalid_irq) + return; + + irq_set_chained_handler(shirq->irq, shirq_handler); + for (i = 0; i < shirq->irq_nr; i++) { + irq_set_chip_and_handler(shirq->irq_base + i, + &shirq_chip, handle_simple_irq); + set_irq_flags(shirq->irq_base + i, IRQF_VALID); + irq_set_chip_data(shirq->irq_base + i, shirq); + } + + irq_set_handler_data(shirq->irq, shirq); +} + +static int __init shirq_init(struct spear_shirq **shirq_blocks, int block_nr, + struct device_node *np) +{ + int i, irq_base, hwirq = 0, irq_nr = 0; + static struct irq_domain *shirq_domain; + void __iomem *base; + + base = of_iomap(np, 0); + if (!base) { + pr_err("%s: failed to map shirq registers\n", __func__); + return -ENXIO; + } + + for (i = 0; i < block_nr; i++) + irq_nr += shirq_blocks[i]->irq_nr; + + irq_base = irq_alloc_descs(-1, 0, irq_nr, 0); + if (IS_ERR_VALUE(irq_base)) { + pr_err("%s: irq desc alloc failed\n", __func__); + goto err_unmap; + } + + shirq_domain = irq_domain_add_legacy(np, irq_nr, irq_base, 0, + &irq_domain_simple_ops, NULL); + if (WARN_ON(!shirq_domain)) { + pr_warn("%s: irq domain init failed\n", __func__); + goto err_free_desc; + } + + for (i = 0; i < block_nr; i++) { + shirq_blocks[i]->base = base; + shirq_blocks[i]->irq_base = irq_find_mapping(shirq_domain, + hwirq); + shirq_blocks[i]->irq = irq_of_parse_and_map(np, i); + + spear_shirq_register(shirq_blocks[i]); + hwirq += shirq_blocks[i]->irq_nr; + } + + return 0; + +err_free_desc: + irq_free_descs(irq_base, irq_nr); +err_unmap: + iounmap(base); + return -ENXIO; +} + +int __init spear300_shirq_of_init(struct device_node *np, + struct device_node *parent) +{ + return shirq_init(spear300_shirq_blocks, + ARRAY_SIZE(spear300_shirq_blocks), np); +} + +int __init spear310_shirq_of_init(struct device_node *np, + struct device_node *parent) +{ + return shirq_init(spear310_shirq_blocks, + ARRAY_SIZE(spear310_shirq_blocks), np); +} + +int __init spear320_shirq_of_init(struct device_node *np, + struct device_node *parent) +{ + return shirq_init(spear320_shirq_blocks, + ARRAY_SIZE(spear320_shirq_blocks), np); +} diff --git a/arch/arm/plat-spear/include/plat/shirq.h b/include/linux/irqchip/spear-shirq.h index 88a7fbd24793..c8be16d213a3 100644 --- a/arch/arm/plat-spear/include/plat/shirq.h +++ b/include/linux/irqchip/spear-shirq.h @@ -1,9 +1,7 @@ /* - * arch/arm/plat-spear/include/plat/shirq.h - * * SPEAr platform shared irq layer header file * - * Copyright (C) 2009 ST Microelectronics + * Copyright (C) 2009-2012 ST Microelectronics * Viresh Kumar <viresh.linux@gmail.com> * * This file is licensed under the terms of the GNU General Public @@ -11,31 +9,15 @@ * warranty of any kind, whether express or implied. */ -#ifndef __PLAT_SHIRQ_H -#define __PLAT_SHIRQ_H +#ifndef __SPEAR_SHIRQ_H +#define __SPEAR_SHIRQ_H #include <linux/irq.h> #include <linux/types.h> /* - * struct shirq_dev_config: shared irq device configuration - * - * virq: virtual irq number of device - * enb_mask: enable mask of device - * status_mask: status mask of device - * clear_mask: clear mask of device - */ -struct shirq_dev_config { - u32 virq; - u32 enb_mask; - u32 status_mask; - u32 clear_mask; -}; - -/* * struct shirq_regs: shared irq register configuration * - * base: base address of shared irq register * enb_reg: enable register offset * reset_to_enb: val 1 indicates, we need to clear bit for enabling interrupt * status_reg: status register offset @@ -44,11 +26,9 @@ struct shirq_dev_config { * reset_to_clear: val 1 indicates, we need to clear bit for clearing interrupt */ struct shirq_regs { - void __iomem *base; u32 enb_reg; u32 reset_to_enb; u32 status_reg; - u32 status_reg_mask; u32 clear_reg; u32 reset_to_clear; }; @@ -57,17 +37,28 @@ struct shirq_regs { * struct spear_shirq: shared irq structure * * irq: hardware irq number - * dev_config: array of device config structures which are using "irq" line - * dev_count: size of dev_config array + * irq_base: base irq in linux domain + * irq_nr: no. of shared interrupts in a particular block + * irq_bit_off: starting bit offset in the status register + * invalid_irq: irq group is currently disabled + * base: base address of shared irq register * regs: register configuration for shared irq block */ struct spear_shirq { u32 irq; - struct shirq_dev_config *dev_config; - u32 dev_count; + u32 irq_base; + u32 irq_nr; + u32 irq_bit_off; + int invalid_irq; + void __iomem *base; struct shirq_regs regs; }; -int spear_shirq_register(struct spear_shirq *shirq); +int __init spear300_shirq_of_init(struct device_node *np, + struct device_node *parent); +int __init spear310_shirq_of_init(struct device_node *np, + struct device_node *parent); +int __init spear320_shirq_of_init(struct device_node *np, + struct device_node *parent); -#endif /* __PLAT_SHIRQ_H */ +#endif /* __SPEAR_SHIRQ_H */ |