diff options
| -rw-r--r-- | Documentation/hwmon/index.rst | 1 | ||||
| -rw-r--r-- | Documentation/hwmon/stpddc60.rst | 90 | ||||
| -rw-r--r-- | MAINTAINERS | 7 | ||||
| -rw-r--r-- | drivers/hwmon/pmbus/Kconfig | 10 | ||||
| -rw-r--r-- | drivers/hwmon/pmbus/Makefile | 1 | ||||
| -rw-r--r-- | drivers/hwmon/pmbus/stpddc60.c | 248 |
6 files changed, 357 insertions, 0 deletions
diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst index b34894403c2b..d4b422edbe3a 100644 --- a/Documentation/hwmon/index.rst +++ b/Documentation/hwmon/index.rst @@ -169,6 +169,7 @@ Hardware Monitoring Kernel Drivers smsc47m192 smsc47m1 sparx5-temp + stpddc60 tc654 tc74 thmc50 diff --git a/Documentation/hwmon/stpddc60.rst b/Documentation/hwmon/stpddc60.rst new file mode 100644 index 000000000000..7f7ce7f7871b --- /dev/null +++ b/Documentation/hwmon/stpddc60.rst @@ -0,0 +1,90 @@ +.. SPDX-License-Identifier: GPL-2.0 + +Kernel driver stpddc60 +====================== + +Supported chips: + + * ST STPDDC60 + + Prefix: 'stpddc60', 'bmr481' + + Addresses scanned: - + + Datasheet: https://flexpowermodules.com/documents/fpm-techspec-bmr481 + +Author: Erik Rosen <erik.rosen@metormote.com> + + +Description +----------- + +This driver supports hardware monitoring for ST STPDDC60 controller chip and +compatible modules. + +The driver is a client driver to the core PMBus driver. Please see +Documentation/hwmon/pmbus.rst and Documentation.hwmon/pmbus-core for details +on PMBus client drivers. + + +Usage Notes +----------- + +This driver does not auto-detect devices. You will have to instantiate the +devices explicitly. Please see Documentation/i2c/instantiating-devices.rst for +details. + +The vout under- and over-voltage limits are set in relation to the commanded +output voltage as a positive or negative offset in the interval 50mV to 400mV +in 50mV steps. This means that the absolute values of the limits will change +when the commanded output voltage changes. Also, care should be taken when +writing to those limits since in the worst case the commanded output voltage +could change at the same time as the limit is written to, wich will lead to +unpredictable results. + + +Platform data support +--------------------- + +The driver supports standard PMBus driver platform data. + + +Sysfs entries +------------- + +The following attributes are supported. Vin, iout, pout and temp limits +are read-write; all other attributes are read-only. + +======================= ======================================================== +in1_label "vin" +in1_input Measured input voltage. +in1_lcrit Critical minimum input voltage. +in1_crit Critical maximum input voltage. +in1_lcrit_alarm Input voltage critical low alarm. +in1_crit_alarm Input voltage critical high alarm. + +in2_label "vout1" +in2_input Measured output voltage. +in2_lcrit Critical minimum output voltage. +in2_crit Critical maximum output voltage. +in2_lcrit_alarm Critical output voltage critical low alarm. +in2_crit_alarm Critical output voltage critical high alarm. + +curr1_label "iout1" +curr1_input Measured output current. +curr1_max Maximum output current. +curr1_max_alarm Output current high alarm. +curr1_crit Critical maximum output current. +curr1_crit_alarm Output current critical high alarm. + +power1_label "pout1" +power1_input Measured output power. +power1_crit Critical maximum output power. +power1_crit_alarm Output power critical high alarm. + +temp1_input Measured maximum temperature of all phases. +temp1_max Maximum temperature limit. +temp1_max_alarm High temperature alarm. +temp1_crit Critical maximum temperature limit. +temp1_crit_alarm Critical maximum temperature alarm. +======================= ======================================================== diff --git a/MAINTAINERS b/MAINTAINERS index aa84121c5611..3aaeab8c6b15 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -16947,6 +16947,13 @@ L: linux-i2c@vger.kernel.org S: Maintained F: drivers/i2c/busses/i2c-stm32* +ST STPDDC60 DRIVER +M: Daniel Nilsson <daniel.nilsson@flex.com> +L: linux-hwmon@vger.kernel.org +S: Maintained +F: Documentation/hwmon/stpddc60.rst +F: drivers/hwmon/pmbus/stpddc60.c + ST VL53L0X ToF RANGER(I2C) IIO DRIVER M: Song Qiang <songqiang1304521@gmail.com> L: linux-iio@vger.kernel.org diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig index ee8c27b3b83d..28658b9f09ff 100644 --- a/drivers/hwmon/pmbus/Kconfig +++ b/drivers/hwmon/pmbus/Kconfig @@ -256,6 +256,16 @@ config SENSORS_Q54SJ108A2 This driver can also be built as a module. If so, the module will be called q54sj108a2. +config SENSORS_STPDDC60 + tristate "ST STPDDC60" + help + If you say yes here you get hardware monitoring support for ST + STPDDC60 Universal Digital Multicell Controller, as well as for + Flex BMR481. + + This driver can also be built as a module. If so, the module will + be called stpddc60. + config SENSORS_TPS40422 tristate "TI TPS40422" help diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile index 685a6bc2b15f..ed1266f6fb01 100644 --- a/drivers/hwmon/pmbus/Makefile +++ b/drivers/hwmon/pmbus/Makefile @@ -29,6 +29,7 @@ obj-$(CONFIG_SENSORS_MP2975) += mp2975.o obj-$(CONFIG_SENSORS_PM6764TR) += pm6764tr.o obj-$(CONFIG_SENSORS_PXE1610) += pxe1610.o obj-$(CONFIG_SENSORS_Q54SJ108A2) += q54sj108a2.o +obj-$(CONFIG_SENSORS_STPDDC60) += stpddc60.o obj-$(CONFIG_SENSORS_TPS40422) += tps40422.o obj-$(CONFIG_SENSORS_TPS53679) += tps53679.o obj-$(CONFIG_SENSORS_UCD9000) += ucd9000.o diff --git a/drivers/hwmon/pmbus/stpddc60.c b/drivers/hwmon/pmbus/stpddc60.c new file mode 100644 index 000000000000..3e6709542b63 --- /dev/null +++ b/drivers/hwmon/pmbus/stpddc60.c @@ -0,0 +1,248 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Hardware monitoring driver for the STPDDC60 controller + * + * Copyright (c) 2021 Flextronics International Sweden AB. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/init.h> +#include <linux/err.h> +#include <linux/i2c.h> +#include <linux/pmbus.h> +#include "pmbus.h" + +#define STPDDC60_MFR_READ_VOUT 0xd2 +#define STPDDC60_MFR_OV_LIMIT_OFFSET 0xe5 +#define STPDDC60_MFR_UV_LIMIT_OFFSET 0xe6 + +static const struct i2c_device_id stpddc60_id[] = { + {"stpddc60", 0}, + {"bmr481", 0}, + {} +}; +MODULE_DEVICE_TABLE(i2c, stpddc60_id); + +static struct pmbus_driver_info stpddc60_info = { + .pages = 1, + .func[0] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT + | PMBUS_HAVE_VIN | PMBUS_HAVE_STATUS_INPUT + | PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP + | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT + | PMBUS_HAVE_POUT, +}; + +/* + * Calculate the closest absolute offset between commanded vout value + * and limit value in steps of 50mv in the range 0 (50mv) to 7 (400mv). + * Return 0 if the upper limit is lower than vout or if the lower limit + * is higher than vout. + */ +static u8 stpddc60_get_offset(int vout, u16 limit, bool over) +{ + int offset; + long v, l; + + v = 250 + (vout - 1) * 5; /* Convert VID to mv */ + l = (limit * 1000L) >> 8; /* Convert LINEAR to mv */ + + if (over == (l < v)) + return 0; + + offset = DIV_ROUND_CLOSEST(abs(l - v), 50); + + if (offset > 0) + offset--; + + return clamp_val(offset, 0, 7); +} + +/* + * Adjust the linear format word to use the given fixed exponent. + */ +static u16 stpddc60_adjust_linear(u16 word, s16 fixed) +{ + s16 e, m, d; + + e = ((s16)word) >> 11; + m = ((s16)((word & 0x7ff) << 5)) >> 5; + d = e - fixed; + + if (d >= 0) + m <<= d; + else + m >>= -d; + + return clamp_val(m, 0, 0x3ff) | ((fixed << 11) & 0xf800); +} + +/* + * The VOUT_COMMAND register uses the VID format but the vout alarm limit + * registers use the LINEAR format so we override VOUT_MODE here to force + * LINEAR format for all registers. + */ +static int stpddc60_read_byte_data(struct i2c_client *client, int page, int reg) +{ + int ret; + + if (page > 0) + return -ENXIO; + + switch (reg) { + case PMBUS_VOUT_MODE: + ret = 0x18; + break; + default: + ret = -ENODATA; + break; + } + + return ret; +} + +/* + * The vout related registers return values in LINEAR11 format when LINEAR16 + * is expected. Clear the top 5 bits to set the exponent part to zero to + * convert the value to LINEAR16 format. + */ +static int stpddc60_read_word_data(struct i2c_client *client, int page, + int phase, int reg) +{ + int ret; + + if (page > 0) + return -ENXIO; + + switch (reg) { + case PMBUS_READ_VOUT: + ret = pmbus_read_word_data(client, page, phase, + STPDDC60_MFR_READ_VOUT); + if (ret < 0) + return ret; + ret &= 0x7ff; + break; + case PMBUS_VOUT_OV_FAULT_LIMIT: + case PMBUS_VOUT_UV_FAULT_LIMIT: + ret = pmbus_read_word_data(client, page, phase, reg); + if (ret < 0) + return ret; + ret &= 0x7ff; + break; + default: + ret = -ENODATA; + break; + } + + return ret; +} + +/* + * The vout under- and over-voltage limits are set as an offset relative to + * the commanded vout voltage. The vin, iout, pout and temp limits must use + * the same fixed exponent the chip uses to encode the data when read. + */ +static int stpddc60_write_word_data(struct i2c_client *client, int page, + int reg, u16 word) +{ + int ret; + u8 offset; + + if (page > 0) + return -ENXIO; + + switch (reg) { + case PMBUS_VOUT_OV_FAULT_LIMIT: + ret = pmbus_read_word_data(client, page, 0xff, + PMBUS_VOUT_COMMAND); + if (ret < 0) + return ret; + offset = stpddc60_get_offset(ret, word, true); + ret = pmbus_write_byte_data(client, page, + STPDDC60_MFR_OV_LIMIT_OFFSET, + offset); + break; + case PMBUS_VOUT_UV_FAULT_LIMIT: + ret = pmbus_read_word_data(client, page, 0xff, + PMBUS_VOUT_COMMAND); + if (ret < 0) + return ret; + offset = stpddc60_get_offset(ret, word, false); + ret = pmbus_write_byte_data(client, page, + STPDDC60_MFR_UV_LIMIT_OFFSET, + offset); + break; + case PMBUS_VIN_OV_FAULT_LIMIT: + case PMBUS_VIN_UV_FAULT_LIMIT: + case PMBUS_OT_FAULT_LIMIT: + case PMBUS_OT_WARN_LIMIT: + case PMBUS_IOUT_OC_FAULT_LIMIT: + case PMBUS_IOUT_OC_WARN_LIMIT: + case PMBUS_POUT_OP_FAULT_LIMIT: + ret = pmbus_read_word_data(client, page, 0xff, reg); + if (ret < 0) + return ret; + word = stpddc60_adjust_linear(word, ret >> 11); + ret = pmbus_write_word_data(client, page, reg, word); + break; + default: + ret = -ENODATA; + break; + } + + return ret; +} + +static int stpddc60_probe(struct i2c_client *client) +{ + int status; + u8 device_id[I2C_SMBUS_BLOCK_MAX + 1]; + const struct i2c_device_id *mid; + struct pmbus_driver_info *info = &stpddc60_info; + + if (!i2c_check_functionality(client->adapter, + I2C_FUNC_SMBUS_READ_BYTE_DATA + | I2C_FUNC_SMBUS_BLOCK_DATA)) + return -ENODEV; + + status = i2c_smbus_read_block_data(client, PMBUS_MFR_MODEL, device_id); + if (status < 0) { + dev_err(&client->dev, "Failed to read Manufacturer Model\n"); + return status; + } + for (mid = stpddc60_id; mid->name[0]; mid++) { + if (!strncasecmp(mid->name, device_id, strlen(mid->name))) + break; + } + if (!mid->name[0]) { + dev_err(&client->dev, "Unsupported device\n"); + return -ENODEV; + } + + info->read_byte_data = stpddc60_read_byte_data; + info->read_word_data = stpddc60_read_word_data; + info->write_word_data = stpddc60_write_word_data; + + status = pmbus_do_probe(client, info); + if (status < 0) + return status; + + pmbus_set_update(client, PMBUS_VOUT_OV_FAULT_LIMIT, true); + pmbus_set_update(client, PMBUS_VOUT_UV_FAULT_LIMIT, true); + + return 0; +} + +static struct i2c_driver stpddc60_driver = { + .driver = { + .name = "stpddc60", + }, + .probe_new = stpddc60_probe, + .id_table = stpddc60_id, +}; + +module_i2c_driver(stpddc60_driver); + +MODULE_AUTHOR("Erik Rosen <erik.rosen@metormote.com>"); +MODULE_DESCRIPTION("PMBus driver for ST STPDDC60"); +MODULE_LICENSE("GPL"); |