aboutsummaryrefslogtreecommitdiff
diff options
context:
space:
mode:
Diffstat
-rw-r--r--Documentation/hwmon/shtc143
-rw-r--r--drivers/hwmon/Kconfig10
-rw-r--r--drivers/hwmon/Makefile1
-rw-r--r--drivers/hwmon/atxp1.c42
-rw-r--r--drivers/hwmon/ina2xx.c7
-rw-r--r--drivers/hwmon/lm85.c33
-rw-r--r--drivers/hwmon/ltc4151.c51
-rw-r--r--drivers/hwmon/shtc1.c251
-rw-r--r--drivers/hwmon/vexpress.c82
-rw-r--r--include/linux/platform_data/shtc1.h23
10 files changed, 401 insertions, 142 deletions
diff --git a/Documentation/hwmon/shtc1 b/Documentation/hwmon/shtc1
new file mode 100644
index 000000000000..6b1e05458f0f
--- /dev/null
+++ b/Documentation/hwmon/shtc1
@@ -0,0 +1,43 @@
+Kernel driver shtc1
+===================
+
+Supported chips:
+ * Sensirion SHTC1
+ Prefix: 'shtc1'
+ Addresses scanned: none
+ Datasheet: http://www.sensirion.com/file/datasheet_shtc1
+
+ * Sensirion SHTW1
+ Prefix: 'shtw1'
+ Addresses scanned: none
+ Datasheet: Not publicly available
+
+Author:
+ Johannes Winkelmann <johannes.winkelmann@sensirion.com>
+
+Description
+-----------
+
+This driver implements support for the Sensirion SHTC1 chip, a humidity and
+temperature sensor. Temperature is measured in degrees celsius, relative
+humidity is expressed as a percentage. Driver can be used as well for SHTW1
+chip, which has the same electrical interface.
+
+The device communicates with the I2C protocol. All sensors are set to I2C
+address 0x70. See Documentation/i2c/instantiating-devices for methods to
+instantiate the device.
+
+There are two options configurable by means of shtc1_platform_data:
+1. blocking (pull the I2C clock line down while performing the measurement) or
+ non-blocking mode. Blocking mode will guarantee the fastest result but
+ the I2C bus will be busy during that time. By default, non-blocking mode
+ is used. Make sure clock-stretching works properly on your device if you
+ want to use blocking mode.
+2. high or low accuracy. High accuracy is used by default and using it is
+ strongly recommended.
+
+sysfs-Interface
+---------------
+
+temp1_input - temperature input
+humidity1_input - humidity input
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index 00343166feb1..08531a128f53 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -1124,6 +1124,16 @@ config SENSORS_SHT21
This driver can also be built as a module. If so, the module
will be called sht21.
+config SENSORS_SHTC1
+ tristate "Sensiron humidity and temperature sensors. SHTC1 and compat."
+ depends on I2C
+ help
+ If you say yes here you get support for the Sensiron SHTC1 and SHTW1
+ humidity and temperature sensors.
+
+ This driver can also be built as a module. If so, the module
+ will be called shtc1.
+
config SENSORS_S3C
tristate "Samsung built-in ADC"
depends on S3C_ADC
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index 11798ad7e801..3dc0f02f71d2 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -126,6 +126,7 @@ obj-$(CONFIG_SENSORS_SCH5627) += sch5627.o
obj-$(CONFIG_SENSORS_SCH5636) += sch5636.o
obj-$(CONFIG_SENSORS_SHT15) += sht15.o
obj-$(CONFIG_SENSORS_SHT21) += sht21.o
+obj-$(CONFIG_SENSORS_SHTC1) += shtc1.o
obj-$(CONFIG_SENSORS_SIS5595) += sis5595.o
obj-$(CONFIG_SENSORS_SMM665) += smm665.o
obj-$(CONFIG_SENSORS_SMSC47B397)+= smsc47b397.o
diff --git a/drivers/hwmon/atxp1.c b/drivers/hwmon/atxp1.c
index 6edce42c61d5..2ae8a304b5ef 100644
--- a/drivers/hwmon/atxp1.c
+++ b/drivers/hwmon/atxp1.c
@@ -45,30 +45,6 @@ MODULE_AUTHOR("Sebastian Witt <se.witt@gmx.net>");
static const unsigned short normal_i2c[] = { 0x37, 0x4e, I2C_CLIENT_END };
-static int atxp1_probe(struct i2c_client *client,
- const struct i2c_device_id *id);
-static int atxp1_remove(struct i2c_client *client);
-static struct atxp1_data *atxp1_update_device(struct device *dev);
-static int atxp1_detect(struct i2c_client *client, struct i2c_board_info *info);
-
-static const struct i2c_device_id atxp1_id[] = {
- { "atxp1", 0 },
- { }
-};
-MODULE_DEVICE_TABLE(i2c, atxp1_id);
-
-static struct i2c_driver atxp1_driver = {
- .class = I2C_CLASS_HWMON,
- .driver = {
- .name = "atxp1",
- },
- .probe = atxp1_probe,
- .remove = atxp1_remove,
- .id_table = atxp1_id,
- .detect = atxp1_detect,
- .address_list = normal_i2c,
-};
-
struct atxp1_data {
struct device *hwmon_dev;
struct mutex update_lock;
@@ -386,4 +362,22 @@ static int atxp1_remove(struct i2c_client *client)
return 0;
};
+static const struct i2c_device_id atxp1_id[] = {
+ { "atxp1", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, atxp1_id);
+
+static struct i2c_driver atxp1_driver = {
+ .class = I2C_CLASS_HWMON,
+ .driver = {
+ .name = "atxp1",
+ },
+ .probe = atxp1_probe,
+ .remove = atxp1_remove,
+ .id_table = atxp1_id,
+ .detect = atxp1_detect,
+ .address_list = normal_i2c,
+};
+
module_i2c_driver(atxp1_driver);
diff --git a/drivers/hwmon/ina2xx.c b/drivers/hwmon/ina2xx.c
index 93d26e8af3e2..bfd3f3eeabcd 100644
--- a/drivers/hwmon/ina2xx.c
+++ b/drivers/hwmon/ina2xx.c
@@ -148,7 +148,8 @@ static int ina2xx_get_value(struct ina2xx_data *data, u8 reg)
switch (reg) {
case INA2XX_SHUNT_VOLTAGE:
- val = DIV_ROUND_CLOSEST(data->regs[reg],
+ /* signed register */
+ val = DIV_ROUND_CLOSEST((s16)data->regs[reg],
data->config->shunt_div);
break;
case INA2XX_BUS_VOLTAGE:
@@ -160,8 +161,8 @@ static int ina2xx_get_value(struct ina2xx_data *data, u8 reg)
val = data->regs[reg] * data->config->power_lsb;
break;
case INA2XX_CURRENT:
- /* LSB=1mA (selected). Is in mA */
- val = data->regs[reg];
+ /* signed register, LSB=1mA (selected), in mA */
+ val = (s16)data->regs[reg];
break;
default:
/* programmer goofed */
diff --git a/drivers/hwmon/lm85.c b/drivers/hwmon/lm85.c
index bed4af358308..b0129a54e1a6 100644
--- a/drivers/hwmon/lm85.c
+++ b/drivers/hwmon/lm85.c
@@ -5,7 +5,7 @@
* Copyright (c) 2002, 2003 Philip Pokorny <ppokorny@penguincomputing.com>
* Copyright (c) 2003 Margit Schubert-While <margitsw@t-online.de>
* Copyright (c) 2004 Justin Thiessen <jthiessen@penguincomputing.com>
- * Copyright (C) 2007--2009 Jean Delvare <jdelvare@suse.de>
+ * Copyright (C) 2007--2014 Jean Delvare <jdelvare@suse.de>
*
* Chip details at <http://www.national.com/ds/LM/LM85.pdf>
*
@@ -39,7 +39,7 @@
static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
enum chips {
- any_chip, lm85b, lm85c,
+ lm85,
adm1027, adt7463, adt7468,
emc6d100, emc6d102, emc6d103, emc6d103s
};
@@ -75,9 +75,6 @@ enum chips {
#define LM85_COMPANY_NATIONAL 0x01
#define LM85_COMPANY_ANALOG_DEV 0x41
#define LM85_COMPANY_SMSC 0x5c
-#define LM85_VERSTEP_VMASK 0xf0
-#define LM85_VERSTEP_GENERIC 0x60
-#define LM85_VERSTEP_GENERIC2 0x70
#define LM85_VERSTEP_LM85C 0x60
#define LM85_VERSTEP_LM85B 0x62
#define LM85_VERSTEP_LM96000_1 0x68
@@ -351,9 +348,9 @@ static const struct i2c_device_id lm85_id[] = {
{ "adm1027", adm1027 },
{ "adt7463", adt7463 },
{ "adt7468", adt7468 },
- { "lm85", any_chip },
- { "lm85b", lm85b },
- { "lm85c", lm85c },
+ { "lm85", lm85 },
+ { "lm85b", lm85 },
+ { "lm85c", lm85 },
{ "emc6d100", emc6d100 },
{ "emc6d101", emc6d100 },
{ "emc6d102", emc6d102 },
@@ -1281,7 +1278,7 @@ static int lm85_detect(struct i2c_client *client, struct i2c_board_info *info)
{
struct i2c_adapter *adapter = client->adapter;
int address = client->addr;
- const char *type_name;
+ const char *type_name = NULL;
int company, verstep;
if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) {
@@ -1297,16 +1294,6 @@ static int lm85_detect(struct i2c_client *client, struct i2c_board_info *info)
"Detecting device at 0x%02x with COMPANY: 0x%02x and VERSTEP: 0x%02x\n",
address, company, verstep);
- /* All supported chips have the version in common */
- if ((verstep & LM85_VERSTEP_VMASK) != LM85_VERSTEP_GENERIC &&
- (verstep & LM85_VERSTEP_VMASK) != LM85_VERSTEP_GENERIC2) {
- dev_dbg(&adapter->dev,
- "Autodetection failed: unsupported version\n");
- return -ENODEV;
- }
- type_name = "lm85";
-
- /* Now, refine the detection */
if (company == LM85_COMPANY_NATIONAL) {
switch (verstep) {
case LM85_VERSTEP_LM85C:
@@ -1323,6 +1310,7 @@ static int lm85_detect(struct i2c_client *client, struct i2c_board_info *info)
"Found Winbond WPCD377I, ignoring\n");
return -ENODEV;
}
+ type_name = "lm85";
break;
}
} else if (company == LM85_COMPANY_ANALOG_DEV) {
@@ -1357,12 +1345,11 @@ static int lm85_detect(struct i2c_client *client, struct i2c_board_info *info)
type_name = "emc6d103s";
break;
}
- } else {
- dev_dbg(&adapter->dev,
- "Autodetection failed: unknown vendor\n");
- return -ENODEV;
}
+ if (!type_name)
+ return -ENODEV;
+
strlcpy(info->type, type_name, I2C_NAME_SIZE);
return 0;
diff --git a/drivers/hwmon/ltc4151.c b/drivers/hwmon/ltc4151.c
index af81be1237c9..c86a18402496 100644
--- a/drivers/hwmon/ltc4151.c
+++ b/drivers/hwmon/ltc4151.c
@@ -47,7 +47,7 @@
#define LTC4151_ADIN_L 0x05
struct ltc4151_data {
- struct device *hwmon_dev;
+ struct i2c_client *client;
struct mutex update_lock;
bool valid;
@@ -59,8 +59,8 @@ struct ltc4151_data {
static struct ltc4151_data *ltc4151_update_device(struct device *dev)
{
- struct i2c_client *client = to_i2c_client(dev);
- struct ltc4151_data *data = i2c_get_clientdata(client);
+ struct ltc4151_data *data = dev_get_drvdata(dev);
+ struct i2c_client *client = data->client;
struct ltc4151_data *ret = data;
mutex_lock(&data->update_lock);
@@ -159,7 +159,7 @@ static SENSOR_DEVICE_ATTR(curr1_input, S_IRUGO, ltc4151_show_value, NULL,
* Finally, construct an array of pointers to members of the above objects,
* as required for sysfs_create_group()
*/
-static struct attribute *ltc4151_attributes[] = {
+static struct attribute *ltc4151_attrs[] = {
&sensor_dev_attr_in1_input.dev_attr.attr,
&sensor_dev_attr_in2_input.dev_attr.attr,
@@ -167,54 +167,30 @@ static struct attribute *ltc4151_attributes[] = {
NULL,
};
-
-static const struct attribute_group ltc4151_group = {
- .attrs = ltc4151_attributes,
-};
+ATTRIBUTE_GROUPS(ltc4151);
static int ltc4151_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct i2c_adapter *adapter = client->adapter;
+ struct device *dev = &client->dev;
struct ltc4151_data *data;
- int ret;
+ struct device *hwmon_dev;
if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
return -ENODEV;
- data = devm_kzalloc(&client->dev, sizeof(*data), GFP_KERNEL);
+ data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
if (!data)
return -ENOMEM;
- i2c_set_clientdata(client, data);
+ data->client = client;
mutex_init(&data->update_lock);
- /* Register sysfs hooks */
- ret = sysfs_create_group(&client->dev.kobj, &ltc4151_group);
- if (ret)
- return ret;
-
- data->hwmon_dev = hwmon_device_register(&client->dev);
- if (IS_ERR(data->hwmon_dev)) {
- ret = PTR_ERR(data->hwmon_dev);
- goto out_hwmon_device_register;
- }
-
- return 0;
-
-out_hwmon_device_register:
- sysfs_remove_group(&client->dev.kobj, &ltc4151_group);
- return ret;
-}
-
-static int ltc4151_remove(struct i2c_client *client)
-{
- struct ltc4151_data *data = i2c_get_clientdata(client);
-
- hwmon_device_unregister(data->hwmon_dev);
- sysfs_remove_group(&client->dev.kobj, &ltc4151_group);
-
- return 0;
+ hwmon_dev = devm_hwmon_device_register_with_groups(dev, client->name,
+ data,
+ ltc4151_groups);
+ return PTR_ERR_OR_ZERO(hwmon_dev);
}
static const struct i2c_device_id ltc4151_id[] = {
@@ -229,7 +205,6 @@ static struct i2c_driver ltc4151_driver = {
.name = "ltc4151",
},
.probe = ltc4151_probe,
- .remove = ltc4151_remove,
.id_table = ltc4151_id,
};
diff --git a/drivers/hwmon/shtc1.c b/drivers/hwmon/shtc1.c
new file mode 100644
index 000000000000..decd7df995ab
--- /dev/null
+++ b/drivers/hwmon/shtc1.c
@@ -0,0 +1,251 @@
+/* Sensirion SHTC1 humidity and temperature sensor driver
+ *
+ * Copyright (C) 2014 Sensirion AG, Switzerland
+ * Author: Johannes Winkelmann <johannes.winkelmann@sensirion.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/err.h>
+#include <linux/delay.h>
+#include <linux/platform_data/shtc1.h>
+
+/* commands (high precision mode) */
+static const unsigned char shtc1_cmd_measure_blocking_hpm[] = { 0x7C, 0xA2 };
+static const unsigned char shtc1_cmd_measure_nonblocking_hpm[] = { 0x78, 0x66 };
+
+/* commands (low precision mode) */
+static const unsigned char shtc1_cmd_measure_blocking_lpm[] = { 0x64, 0x58 };
+static const unsigned char shtc1_cmd_measure_nonblocking_lpm[] = { 0x60, 0x9c };
+
+/* command for reading the ID register */
+static const unsigned char shtc1_cmd_read_id_reg[] = { 0xef, 0xc8 };
+
+/* constants for reading the ID register */
+#define SHTC1_ID 0x07
+#define SHTC1_ID_REG_MASK 0x1f
+
+/* delays for non-blocking i2c commands, both in us */
+#define SHTC1_NONBLOCKING_WAIT_TIME_HPM 14400
+#define SHTC1_NONBLOCKING_WAIT_TIME_LPM 1000
+
+#define SHTC1_CMD_LENGTH 2
+#define SHTC1_RESPONSE_LENGTH 6
+
+struct shtc1_data {
+ struct i2c_client *client;
+ struct mutex update_lock;
+ bool valid;
+ unsigned long last_updated; /* in jiffies */
+
+ const unsigned char *command;
+ unsigned int nonblocking_wait_time; /* in us */
+
+ struct shtc1_platform_data setup;
+
+ int temperature; /* 1000 * temperature in dgr C */
+ int humidity; /* 1000 * relative humidity in %RH */
+};
+
+static int shtc1_update_values(struct i2c_client *client,
+ struct shtc1_data *data,
+ char *buf, int bufsize)
+{
+ int ret = i2c_master_send(client, data->command, SHTC1_CMD_LENGTH);
+ if (ret != SHTC1_CMD_LENGTH) {
+ dev_err(&client->dev, "failed to send command: %d\n", ret);
+ return ret < 0 ? ret : -EIO;
+ }
+
+ /*
+ * In blocking mode (clock stretching mode) the I2C bus
+ * is blocked for other traffic, thus the call to i2c_master_recv()
+ * will wait until the data is ready. For non blocking mode, we
+ * have to wait ourselves.
+ */
+ if (!data->setup.blocking_io)
+ usleep_range(data->nonblocking_wait_time,
+ data->nonblocking_wait_time + 1000);
+
+ ret = i2c_master_recv(client, buf, bufsize);
+ if (ret != bufsize) {
+ dev_err(&client->dev, "failed to read values: %d\n", ret);
+ return ret < 0 ? ret : -EIO;
+ }
+
+ return 0;
+}
+
+/* sysfs attributes */
+static struct shtc1_data *shtc1_update_client(struct device *dev)
+{
+ struct shtc1_data *data = dev_get_drvdata(dev);
+ struct i2c_client *client = data->client;
+ unsigned char buf[SHTC1_RESPONSE_LENGTH];
+ int val;
+ int ret = 0;
+
+ mutex_lock(&data->update_lock);
+
+ if (time_after(jiffies, data->last_updated + HZ / 10) || !data->valid) {
+ ret = shtc1_update_values(client, data, buf, sizeof(buf));
+ if (ret)
+ goto out;
+
+ /*
+ * From datasheet:
+ * T = -45 + 175 * ST / 2^16
+ * RH = 100 * SRH / 2^16
+ *
+ * Adapted for integer fixed point (3 digit) arithmetic.
+ */
+ val = be16_to_cpup((__be16 *)buf);
+ data->temperature = ((21875 * val) >> 13) - 45000;
+ val = be16_to_cpup((__be16 *)(buf + 3));
+ data->humidity = ((12500 * val) >> 13);
+
+ data->last_updated = jiffies;
+ data->valid = true;
+ }
+
+out:
+ mutex_unlock(&data->update_lock);
+
+ return ret == 0 ? data : ERR_PTR(ret);
+}
+
+static ssize_t temp1_input_show(struct device *dev,
+ struct device_attribute *attr,
+ char *buf)
+{
+ struct shtc1_data *data = shtc1_update_client(dev);
+ if (IS_ERR(data))
+ return PTR_ERR(data);
+
+ return sprintf(buf, "%d\n", data->temperature);
+}
+
+static ssize_t humidity1_input_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct shtc1_data *data = shtc1_update_client(dev);
+ if (IS_ERR(data))
+ return PTR_ERR(data);
+
+ return sprintf(buf, "%d\n", data->humidity);
+}
+
+static DEVICE_ATTR_RO(temp1_input);
+static DEVICE_ATTR_RO(humidity1_input);
+
+static struct attribute *shtc1_attrs[] = {
+ &dev_attr_temp1_input.attr,
+ &dev_attr_humidity1_input.attr,
+ NULL
+};
+
+ATTRIBUTE_GROUPS(shtc1);
+
+static void shtc1_select_command(struct shtc1_data *data)
+{
+ if (data->setup.high_precision) {
+ data->command = data->setup.blocking_io ?
+ shtc1_cmd_measure_blocking_hpm :
+ shtc1_cmd_measure_nonblocking_hpm;
+ data->nonblocking_wait_time = SHTC1_NONBLOCKING_WAIT_TIME_HPM;
+
+ } else {
+ data->command = data->setup.blocking_io ?
+ shtc1_cmd_measure_blocking_lpm :
+ shtc1_cmd_measure_nonblocking_lpm;
+ data->nonblocking_wait_time = SHTC1_NONBLOCKING_WAIT_TIME_LPM;
+ }
+}
+
+static int shtc1_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ int ret;
+ char id_reg[2];
+ struct shtc1_data *data;
+ struct device *hwmon_dev;
+ struct i2c_adapter *adap = client->adapter;
+ struct device *dev = &client->dev;
+
+ if (!i2c_check_functionality(adap, I2C_FUNC_I2C)) {
+ dev_err(dev, "plain i2c transactions not supported\n");
+ return -ENODEV;
+ }
+
+ ret = i2c_master_send(client, shtc1_cmd_read_id_reg, SHTC1_CMD_LENGTH);
+ if (ret != SHTC1_CMD_LENGTH) {
+ dev_err(dev, "could not send read_id_reg command: %d\n", ret);
+ return ret < 0 ? ret : -ENODEV;
+ }
+ ret = i2c_master_recv(client, id_reg, sizeof(id_reg));
+ if (ret != sizeof(id_reg)) {
+ dev_err(dev, "could not read ID register: %d\n", ret);
+ return -ENODEV;
+ }
+ if ((id_reg[1] & SHTC1_ID_REG_MASK) != SHTC1_ID) {
+ dev_err(dev, "ID register doesn't match\n");
+ return -ENODEV;
+ }
+
+ data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ data->setup.blocking_io = false;
+ data->setup.high_precision = true;
+ data->client = client;
+
+ if (client->dev.platform_data)
+ data->setup = *(struct shtc1_platform_data *)dev->platform_data;
+ shtc1_select_command(data);
+ mutex_init(&data->update_lock);
+
+ hwmon_dev = devm_hwmon_device_register_with_groups(dev,
+ client->name,
+ data,
+ shtc1_groups);
+ if (IS_ERR(hwmon_dev))
+ dev_dbg(dev, "unable to register hwmon device\n");
+
+ return PTR_ERR_OR_ZERO(hwmon_dev);
+}
+
+/* device ID table */
+static const struct i2c_device_id shtc1_id[] = {
+ { "shtc1", 0 },
+ { "shtw1", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, shtc1_id);
+
+static struct i2c_driver shtc1_i2c_driver = {
+ .driver.name = "shtc1",
+ .probe = shtc1_probe,
+ .id_table = shtc1_id,
+};
+
+module_i2c_driver(shtc1_i2c_driver);
+
+MODULE_AUTHOR("Johannes Winkelmann <johannes.winkelmann@sensirion.com>");
+MODULE_DESCRIPTION("Sensirion SHTC1 humidity and temperature sensor driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/hwmon/vexpress.c b/drivers/hwmon/vexpress.c
index 611f34c7333d..c53619086f33 100644
--- a/drivers/hwmon/vexpress.c
+++ b/drivers/hwmon/vexpress.c
@@ -27,17 +27,8 @@
struct vexpress_hwmon_data {
struct device *hwmon_dev;
struct regmap *reg;
- const char *name;
};
-static ssize_t vexpress_hwmon_name_show(struct device *dev,
- struct device_attribute *dev_attr, char *buffer)
-{
- struct vexpress_hwmon_data *data = dev_get_drvdata(dev);
-
- return sprintf(buffer, "%s\n", data->name);
-}
-
static ssize_t vexpress_hwmon_label_show(struct device *dev,
struct device_attribute *dev_attr, char *buffer)
{
@@ -95,16 +86,6 @@ static umode_t vexpress_hwmon_attr_is_visible(struct kobject *kobj,
return attr->mode;
}
-static DEVICE_ATTR(name, S_IRUGO, vexpress_hwmon_name_show, NULL);
-
-#define VEXPRESS_HWMON_ATTRS(_name, _label_attr, _input_attr) \
-struct attribute *vexpress_hwmon_attrs_##_name[] = { \
- &dev_attr_name.attr, \
- &dev_attr_##_label_attr.attr, \
- &sensor_dev_attr_##_input_attr.dev_attr.attr, \
- NULL \
-}
-
struct vexpress_hwmon_type {
const char *name;
const struct attribute_group **attr_groups;
@@ -114,7 +95,11 @@ struct vexpress_hwmon_type {
static DEVICE_ATTR(in1_label, S_IRUGO, vexpress_hwmon_label_show, NULL);
static SENSOR_DEVICE_ATTR(in1_input, S_IRUGO, vexpress_hwmon_u32_show,
NULL, 1000);
-static VEXPRESS_HWMON_ATTRS(volt, in1_label, in1_input);
+static struct attribute *vexpress_hwmon_attrs_volt[] = {
+ &dev_attr_in1_label.attr,
+ &sensor_dev_attr_in1_input.dev_attr.attr,
+ NULL
+};
static struct attribute_group vexpress_hwmon_group_volt = {
.is_visible = vexpress_hwmon_attr_is_visible,
.attrs = vexpress_hwmon_attrs_volt,
@@ -131,7 +116,11 @@ static struct vexpress_hwmon_type vexpress_hwmon_volt = {
static DEVICE_ATTR(curr1_label, S_IRUGO, vexpress_hwmon_label_show, NULL);
static SENSOR_DEVICE_ATTR(curr1_input, S_IRUGO, vexpress_hwmon_u32_show,
NULL, 1000);
-static VEXPRESS_HWMON_ATTRS(amp, curr1_label, curr1_input);
+static struct attribute *vexpress_hwmon_attrs_amp[] = {
+ &dev_attr_curr1_label.attr,
+ &sensor_dev_attr_curr1_input.dev_attr.attr,
+ NULL
+};
static struct attribute_group vexpress_hwmon_group_amp = {
.is_visible = vexpress_hwmon_attr_is_visible,
.attrs = vexpress_hwmon_attrs_amp,
@@ -147,7 +136,11 @@ static struct vexpress_hwmon_type vexpress_hwmon_amp = {
static DEVICE_ATTR(temp1_label, S_IRUGO, vexpress_hwmon_label_show, NULL);
static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, vexpress_hwmon_u32_show,
NULL, 1000);
-static VEXPRESS_HWMON_ATTRS(temp, temp1_label, temp1_input);
+static struct attribute *vexpress_hwmon_attrs_temp[] = {
+ &dev_attr_temp1_label.attr,
+ &sensor_dev_attr_temp1_input.dev_attr.attr,
+ NULL
+};
static struct attribute_group vexpress_hwmon_group_temp = {
.is_visible = vexpress_hwmon_attr_is_visible,
.attrs = vexpress_hwmon_attrs_temp,
@@ -163,7 +156,11 @@ static struct vexpress_hwmon_type vexpress_hwmon_temp = {
static DEVICE_ATTR(power1_label, S_IRUGO, vexpress_hwmon_label_show, NULL);
static SENSOR_DEVICE_ATTR(power1_input, S_IRUGO, vexpress_hwmon_u32_show,
NULL, 1);
-static VEXPRESS_HWMON_ATTRS(power, power1_label, power1_input);
+static struct attribute *vexpress_hwmon_attrs_power[] = {
+ &dev_attr_power1_label.attr,
+ &sensor_dev_attr_power1_input.dev_attr.attr,
+ NULL
+};
static struct attribute_group vexpress_hwmon_group_power = {
.is_visible = vexpress_hwmon_attr_is_visible,
.attrs = vexpress_hwmon_attrs_power,
@@ -179,7 +176,11 @@ static struct vexpress_hwmon_type vexpress_hwmon_power = {
static DEVICE_ATTR(energy1_label, S_IRUGO, vexpress_hwmon_label_show, NULL);
static SENSOR_DEVICE_ATTR(energy1_input, S_IRUGO, vexpress_hwmon_u64_show,
NULL, 1);
-static VEXPRESS_HWMON_ATTRS(energy, energy1_label, energy1_input);
+static struct attribute *vexpress_hwmon_attrs_energy[] = {
+ &dev_attr_energy1_label.attr,
+ &sensor_dev_attr_energy1_input.dev_attr.attr,
+ NULL
+};
static struct attribute_group vexpress_hwmon_group_energy = {
.is_visible = vexpress_hwmon_attr_is_visible,
.attrs = vexpress_hwmon_attrs_energy,
@@ -218,7 +219,6 @@ MODULE_DEVICE_TABLE(of, vexpress_hwmon_of_match);
static int vexpress_hwmon_probe(struct platform_device *pdev)
{
- int err;
const struct of_device_id *match;
struct vexpress_hwmon_data *data;
const struct vexpress_hwmon_type *type;
@@ -232,45 +232,19 @@ static int vexpress_hwmon_probe(struct platform_device *pdev)
if (!match)
return -ENODEV;
type = match->data;
- data->name = type->name;
data->reg = devm_regmap_init_vexpress_config(&pdev->dev);
if (IS_ERR(data->reg))
return PTR_ERR(data->reg);
- err = sysfs_create_groups(&pdev->dev.kobj, type->attr_groups);
- if (err)
- goto error;
-
- data->hwmon_dev = hwmon_device_register(&pdev->dev);
- if (IS_ERR(data->hwmon_dev)) {
- err = PTR_ERR(data->hwmon_dev);
- goto error;
- }
-
- return 0;
-
-error:
- sysfs_remove_group(&pdev->dev.kobj, match->data);
- return err;
-}
-
-static int vexpress_hwmon_remove(struct platform_device *pdev)
-{
- struct vexpress_hwmon_data *data = platform_get_drvdata(pdev);
- const struct of_device_id *match;
-
- hwmon_device_unregister(data->hwmon_dev);
-
- match = of_match_device(vexpress_hwmon_of_match, &pdev->dev);
- sysfs_remove_group(&pdev->dev.kobj, match->data);
+ data->hwmon_dev = devm_hwmon_device_register_with_groups(&pdev->dev,
+ type->name, data, type->attr_groups);
- return 0;
+ return PTR_ERR_OR_ZERO(data->hwmon_dev);
}
static struct platform_driver vexpress_hwmon_driver = {
.probe = vexpress_hwmon_probe,
- .remove = vexpress_hwmon_remove,
.driver = {
.name = DRVNAME,
.owner = THIS_MODULE,
diff --git a/include/linux/platform_data/shtc1.h b/include/linux/platform_data/shtc1.h
new file mode 100644
index 000000000000..7b8c353f7dc8
--- /dev/null
+++ b/include/linux/platform_data/shtc1.h
@@ -0,0 +1,23 @@
+/*
+ * Copyright (C) 2014 Sensirion AG, Switzerland
+ * Author: Johannes Winkelmann <johannes.winkelmann@sensirion.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef __SHTC1_H_
+#define __SHTC1_H_
+
+struct shtc1_platform_data {
+ bool blocking_io;
+ bool high_precision;
+};
+#endif /* __SHTC1_H_ */
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-19 09:20:37 +0000