diff options
351 files changed, 7825 insertions, 40990 deletions
diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio index faaa2166d741..d3e53a6d8331 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio +++ b/Documentation/ABI/testing/sysfs-bus-iio @@ -1726,3 +1726,16 @@ Contact: linux-iio@vger.kernel.org Description: List of valid periods (in seconds) for which the light intensity must be above the threshold level before interrupt is asserted. + +What: /sys/bus/iio/devices/iio:deviceX/in_filter_notch_center_frequency +KernelVersion: 5.5 +Contact: linux-iio@vger.kernel.org +Description: + Center frequency in Hz for a notch filter. Used i.e. for line + noise suppression. + +What: /sys/bus/iio/devices/iio:deviceX/in_temp_thermocouple_type +KernelVersion: 5.5 +Contact: linux-iio@vger.kernel.org +Description: + One of the following thermocouple types: B, E, J, K, N, R, S, T. diff --git a/Documentation/ABI/testing/sysfs-bus-iio-dma-buffer b/Documentation/ABI/testing/sysfs-bus-iio-dma-buffer new file mode 100644 index 000000000000..d526e6571001 --- /dev/null +++ b/Documentation/ABI/testing/sysfs-bus-iio-dma-buffer @@ -0,0 +1,19 @@ +What: /sys/bus/iio/devices/iio:deviceX/buffer/length_align_bytes +KernelVersion: 5.4 +Contact: linux-iio@vger.kernel.org +Description: + DMA buffers tend to have a alignment requirement for the + buffers. If this alignment requirement is not met samples might + be dropped from the buffer. + + This property reports the alignment requirements in bytes. + This means that the buffer size in bytes needs to be a integer + multiple of the number reported by this file. + + The alignment requirements in number of sample sets will depend + on the enabled channels and the bytes per channel. This means + that the alignment requirement in samples sets might change + depending on which and how many channels are enabled. Whereas + the alignment requirement reported in bytes by this property + will remain static and does not depend on which channels are + enabled. diff --git a/Documentation/devicetree/bindings/iio/accel/adi,adis16240.yaml b/Documentation/devicetree/bindings/iio/accel/adi,adis16240.yaml new file mode 100644 index 000000000000..4147f02b5e3c --- /dev/null +++ b/Documentation/devicetree/bindings/iio/accel/adi,adis16240.yaml @@ -0,0 +1,49 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/accel/adi,adis16240.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ADIS16240 Programmable Impact Sensor and Recorder driver + +maintainers: + - Alexandru Ardelean <alexandru.ardelean@analog.com> + +description: | + ADIS16240 Programmable Impact Sensor and Recorder driver that supports + SPI interface. + https://www.analog.com/en/products/adis16240.html + +properties: + compatible: + enum: + - adi,adis16240 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + spi0 { + #address-cells = <1>; + #size-cells = <0>; + + /* Example for a SPI device node */ + accelerometer@0 { + compatible = "adi,adis16240"; + reg = <0>; + spi-max-frequency = <2500000>; + interrupt-parent = <&gpio0>; + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; + }; + }; diff --git a/Documentation/devicetree/bindings/iio/accel/bma180.txt b/Documentation/devicetree/bindings/iio/accel/bma180.txt index 3b25b4c4d446..f53237270b32 100644 --- a/Documentation/devicetree/bindings/iio/accel/bma180.txt +++ b/Documentation/devicetree/bindings/iio/accel/bma180.txt @@ -1,11 +1,14 @@ -* Bosch BMA180 / BMA250 triaxial acceleration sensor +* Bosch BMA180 / BMA25x triaxial acceleration sensor http://omapworld.com/BMA180_111_1002839.pdf http://ae-bst.resource.bosch.com/media/products/dokumente/bma250/bst-bma250-ds002-05.pdf Required properties: - - compatible : should be "bosch,bma180" or "bosch,bma250" + - compatible : should be one of: + "bosch,bma180" + "bosch,bma250" + "bosch,bma254" - reg : the I2C address of the sensor Optional properties: diff --git a/Documentation/devicetree/bindings/iio/accel/bosch,bma400.yaml b/Documentation/devicetree/bindings/iio/accel/bosch,bma400.yaml new file mode 100644 index 000000000000..c1c6d6f223cf --- /dev/null +++ b/Documentation/devicetree/bindings/iio/accel/bosch,bma400.yaml @@ -0,0 +1,54 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/accel/bosch,bma400.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Bosch BMA400 triaxial acceleration sensor + +maintainers: + - Dan Robertson <dan@dlrobertson.com> + +description: | + Acceleration and temperature iio sensors with an i2c interface + + Specifications about the sensor can be found at: + https://ae-bst.resource.bosch.com/media/_tech/media/datasheets/BST-BMA400-DS000.pdf + +properties: + compatible: + enum: + - bosch,bma400 + + reg: + maxItems: 1 + + vdd-supply: + description: phandle to the regulator that provides power to the accelerometer + + vddio-supply: + description: phandle to the regulator that provides power to the sensor's IO + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + accelerometer@14 { + compatible = "bosch,bma400"; + reg = <0x14>; + vdd-supply = <&vdd>; + vddio-supply = <&vddio>; + interrupt-parent = <&gpio0>; + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; + }; + }; diff --git a/Documentation/devicetree/bindings/iio/accel/kionix,kxcjk1013.txt b/Documentation/devicetree/bindings/iio/accel/kionix,kxcjk1013.txt index eb76a02e2a82..ce950e162d5d 100644 --- a/Documentation/devicetree/bindings/iio/accel/kionix,kxcjk1013.txt +++ b/Documentation/devicetree/bindings/iio/accel/kionix,kxcjk1013.txt @@ -9,9 +9,16 @@ Required properties: "kionix,kxtf9" - reg: i2c slave address +Optional properties: + + - mount-matrix: an optional 3x3 mounting rotation matrix + Example: kxtf9@f { compatible = "kionix,kxtf9"; reg = <0x0F>; + mount-matrix = "0", "1", "0", + "1", "0", "0", + "0", "0", "1"; }; diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7091r5.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7091r5.yaml new file mode 100644 index 000000000000..31ffa275f5fa --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7091r5.yaml @@ -0,0 +1,54 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/adi,ad7091r5.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices AD7091R5 4-Channel 12-Bit ADC + +maintainers: + - Beniamin Bia <beniamin.bia@analog.com> + +description: | + Analog Devices AD7091R5 4-Channel 12-Bit ADC + https://www.analog.com/media/en/technical-documentation/data-sheets/ad7091r-5.pdf + +properties: + compatible: + enum: + - adi,ad7091r5 + + reg: + maxItems: 1 + + vref-supply: + description: + Phandle to the vref power supply + + interrupts: + maxItems: 1 + + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + adc@2f { + compatible = "adi,ad7091r5"; + reg = <0x2f>; + + interrupts = <25 IRQ_TYPE_EDGE_FALLING>; + interrupt-parent = <&gpio>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/adc/lltc,ltc2496.yaml b/Documentation/devicetree/bindings/iio/adc/lltc,ltc2496.yaml new file mode 100644 index 000000000000..59009997dca0 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/lltc,ltc2496.yaml @@ -0,0 +1,47 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/lltc,ltc2496.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Linear Technology / Analog Devices LTC2496 ADC + +maintainers: + - Lars-Peter Clausen <lars@metafoo.de> + - Michael Hennerich <Michael.Hennerich@analog.com> + - Stefan Popa <stefan.popa@analog.com> + +properties: + compatible: + enum: + - lltc,ltc2496 + + vref-supply: + description: phandle to an external regulator providing the reference voltage + allOf: + - $ref: /schemas/types.yaml#/definitions/phandle + + reg: + description: spi chipselect number according to the usual spi bindings + + spi-max-frequency: + description: maximal spi bus frequency supported + +required: + - compatible + - vref-supply + - reg + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + adc@0 { + compatible = "lltc,ltc2496"; + reg = <0>; + vref-supply = <<c2496_reg>; + spi-max-frequency = <2000000>; + }; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/sigma-delta-modulator.txt b/Documentation/devicetree/bindings/iio/adc/sigma-delta-modulator.txt deleted file mode 100644 index 59b92cd32552..000000000000 --- a/Documentation/devicetree/bindings/iio/adc/sigma-delta-modulator.txt +++ /dev/null @@ -1,13 +0,0 @@ -Device-Tree bindings for sigma delta modulator - -Required properties: -- compatible: should be "ads1201", "sd-modulator". "sd-modulator" can be use - as a generic SD modulator if modulator not specified in compatible list. -- #io-channel-cells = <0>: See the IIO bindings section "IIO consumers". - -Example node: - - ads1202: adc { - compatible = "sd-modulator"; - #io-channel-cells = <0>; - }; diff --git a/Documentation/devicetree/bindings/iio/adc/sigma-delta-modulator.yaml b/Documentation/devicetree/bindings/iio/adc/sigma-delta-modulator.yaml new file mode 100644 index 000000000000..a390343d0c2a --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/sigma-delta-modulator.yaml @@ -0,0 +1,37 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/sigma-delta-modulator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Device-Tree bindings for sigma delta modulator + +maintainers: + - Arnaud Pouliquen <arnaud.pouliquen@st.com> + +properties: + compatible: + description: | + "sd-modulator" can be used as a generic SD modulator, + if the modulator is not specified in the compatible list. + enum: + - sd-modulator + - ads1201 + + '#io-channel-cells': + const: 0 + +required: + - compatible + - '#io-channel-cells' + +additionalProperties: false + +examples: + - | + ads1202: adc { + compatible = "sd-modulator"; + #io-channel-cells = <0>; + }; + +... diff --git a/Documentation/devicetree/bindings/iio/imu/adi,adis16480.txt b/Documentation/devicetree/bindings/iio/imu/adi,adis16480.txt index ed7783f45233..cd903a1d880d 100644 --- a/Documentation/devicetree/bindings/iio/imu/adi,adis16480.txt +++ b/Documentation/devicetree/bindings/iio/imu/adi,adis16480.txt @@ -8,6 +8,7 @@ Required properties for the ADIS16480: * "adi,adis16480" * "adi,adis16485" * "adi,adis16488" + * "adi,adis16490" * "adi,adis16495-1" * "adi,adis16495-2" * "adi,adis16495-3" diff --git a/Documentation/devicetree/bindings/iio/pressure/asc,dlhl60d.yaml b/Documentation/devicetree/bindings/iio/pressure/asc,dlhl60d.yaml new file mode 100644 index 000000000000..9f5ca9c42025 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/pressure/asc,dlhl60d.yaml @@ -0,0 +1,51 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/pressure/asc,dlhl60d.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: All Sensors DLH series low voltage digital pressure sensors + +maintainers: + - Tomislav Denis <tomislav.denis@avl.com> + +description: | + Bindings for the All Sensors DLH series pressure sensors. + + Specifications about the sensors can be found at: + http://www.allsensors.com/cad/DS-0355_Rev_B.PDF + +properties: + compatible: + enum: + - asc,dlhl60d + - asc,dlhl60g + + reg: + description: I2C device address + maxItems: 1 + + interrupts: + description: interrupt mapping for EOC(data ready) pin + maxItems: 1 + +required: + - compatible + - reg + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + pressure@29 { + compatible = "asc,dlhl60d"; + reg = <0x29>; + interrupt-parent = <&gpio0>; + interrupts = <10 IRQ_TYPE_EDGE_RISING>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/proximity/parallax-ping.yaml b/Documentation/devicetree/bindings/iio/proximity/parallax-ping.yaml new file mode 100644 index 000000000000..a079c9921af6 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/proximity/parallax-ping.yaml @@ -0,0 +1,51 @@ +# SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/proximity/parallax-ping.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Parallax PING))) and LaserPING range finder + +maintainers: + - Andreas Klinger <ak@it-klinger.de> + +description: | + Bit-banging driver using one GPIO: + - ping-gpios is raised by the driver to start measurement + - direction of ping-gpio is then switched into input with an interrupt + for receiving distance value as PWM signal + + Specifications about the devices can be found at: + http://parallax.com/sites/default/files/downloads/28041-LaserPING-2m-Rangefinder-Guide.pdf + http://parallax.com/sites/default/files/downloads/28015-PING-Documentation-v1.6.pdf + +properties: + compatible: + enum: + - parallax,ping + - parallax,laserping + + ping-gpios: + description: + Definition of the GPIO for the triggering and echo (output and input) + This GPIO is set for about 5 us by the driver to tell the device it + should initiate the measurement cycle. Afterwards the GPIO is switched + to input direction with an interrupt. The device sets it and the + length of the input signal corresponds to the measured distance. + It needs to be an GPIO which is able to deliver an interrupt because + the time between two interrupts is measured in the driver. + See Documentation/devicetree/bindings/gpio/gpio.txt for information + on how to specify a consumer gpio. + maxItems: 1 + +required: + - compatible + - ping-gpios + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + proximity { + compatible = "parallax,laserping"; + ping-gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/iio/temperature/maxim_thermocouple.txt b/Documentation/devicetree/bindings/iio/temperature/maxim_thermocouple.txt index 28bc5c4d965b..bb85cd0e039c 100644 --- a/Documentation/devicetree/bindings/iio/temperature/maxim_thermocouple.txt +++ b/Documentation/devicetree/bindings/iio/temperature/maxim_thermocouple.txt @@ -5,7 +5,10 @@ Maxim thermocouple support Required properties: - - compatible: must be "maxim,max31855" or "maxim,max6675" + - compatible: must be "maxim,max6675" or one of the following: + "maxim,max31855k", "maxim,max31855j", "maxim,max31855n", + "maxim,max31855s", "maxim,max31855t", "maxim,max31855e", + "maxim,max31855r"; the generic "max,max31855" is deprecated. - reg: SPI chip select number for the device - spi-max-frequency: must be 4300000 - spi-cpha: must be defined for max6675 to enable SPI mode 1 @@ -15,7 +18,7 @@ Required properties: Example: max31855@0 { - compatible = "maxim,max31855"; + compatible = "maxim,max31855k"; reg = <0>; spi-max-frequency = <4300000>; }; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index 9cb3bc683db7..315ebac520b3 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -109,6 +109,8 @@ patternProperties: description: Artesyn Embedded Technologies Inc. "^asahi-kasei,.*": description: Asahi Kasei Corp. + "^asc,.*": + description: All Sensors Corporation "^aspeed,.*": description: ASPEED Technology Inc. "^asus,.*": @@ -717,6 +719,8 @@ patternProperties: description: Panasonic Corporation "^parade,.*": description: Parade Technologies Inc. + "^parallax,.*": + description: Parallax Inc. "^pda,.*": description: Precision Design Associates, Inc. "^pericom,.*": diff --git a/Documentation/isdn/avmb1.rst b/Documentation/isdn/avmb1.rst deleted file mode 100644 index de3961e67553..000000000000 --- a/Documentation/isdn/avmb1.rst +++ /dev/null @@ -1,246 +0,0 @@ -================================ -Driver for active AVM Controller -================================ - -The driver provides a kernel capi2.0 Interface (kernelcapi) and -on top of this a User-Level-CAPI2.0-interface (capi) -and a driver to connect isdn4linux with CAPI2.0 (capidrv). -The lowlevel interface can be used to implement a CAPI2.0 -also for passive cards since July 1999. - -The author can be reached at calle@calle.in-berlin.de. -The command avmcapictrl is part of the isdn4k-utils. -t4-files can be found at ftp://ftp.avm.de/cardware/b1/linux/firmware - -Currently supported cards: - - - B1 ISA (all versions) - - B1 PCI - - T1/T1B (HEMA card) - - M1 - - M2 - - B1 PCMCIA - -Installing ----------- - -You need at least /dev/capi20 to load the firmware. - -:: - - mknod /dev/capi20 c 68 0 - mknod /dev/capi20.00 c 68 1 - mknod /dev/capi20.01 c 68 2 - . - . - . - mknod /dev/capi20.19 c 68 20 - -Running -------- - -To use the card you need the t4-files to download the firmware. -AVM GmbH provides several t4-files for the different D-channel -protocols (b1.t4 for Euro-ISDN). Install these file in /lib/isdn. - -if you configure as modules load the modules this way:: - - insmod /lib/modules/current/misc/capiutil.o - insmod /lib/modules/current/misc/b1.o - insmod /lib/modules/current/misc/kernelcapi.o - insmod /lib/modules/current/misc/capidrv.o - insmod /lib/modules/current/misc/capi.o - -if you have an B1-PCI card load the module b1pci.o:: - - insmod /lib/modules/current/misc/b1pci.o - -and load the firmware with:: - - avmcapictrl load /lib/isdn/b1.t4 1 - -if you have an B1-ISA card load the module b1isa.o -and add the card by calling:: - - avmcapictrl add 0x150 15 - -and load the firmware by calling:: - - avmcapictrl load /lib/isdn/b1.t4 1 - -if you have an T1-ISA card load the module t1isa.o -and add the card by calling:: - - avmcapictrl add 0x450 15 T1 0 - -and load the firmware by calling:: - - avmcapictrl load /lib/isdn/t1.t4 1 - -if you have an PCMCIA card (B1/M1/M2) load the module b1pcmcia.o -before you insert the card. - -Leased Lines with B1 --------------------- - -Init card and load firmware. - -For an D64S use "FV: 1" as phone number - -For an D64S2 use "FV: 1" and "FV: 2" for multilink -or "FV: 1,2" to use CAPI channel bundling. - -/proc-Interface ------------------ - -/proc/capi:: - - dr-xr-xr-x 2 root root 0 Jul 1 14:03 . - dr-xr-xr-x 82 root root 0 Jun 30 19:08 .. - -r--r--r-- 1 root root 0 Jul 1 14:03 applications - -r--r--r-- 1 root root 0 Jul 1 14:03 applstats - -r--r--r-- 1 root root 0 Jul 1 14:03 capi20 - -r--r--r-- 1 root root 0 Jul 1 14:03 capidrv - -r--r--r-- 1 root root 0 Jul 1 14:03 controller - -r--r--r-- 1 root root 0 Jul 1 14:03 contrstats - -r--r--r-- 1 root root 0 Jul 1 14:03 driver - -r--r--r-- 1 root root 0 Jul 1 14:03 ncci - -r--r--r-- 1 root root 0 Jul 1 14:03 users - -/proc/capi/applications: - applid level3cnt datablkcnt datablklen ncci-cnt recvqueuelen - level3cnt: - capi_register parameter - datablkcnt: - capi_register parameter - ncci-cnt: - current number of nccis (connections) - recvqueuelen: - number of messages on receive queue - - for example:: - - 1 -2 16 2048 1 0 - 2 2 7 2048 1 0 - -/proc/capi/applstats: - applid recvctlmsg nrecvdatamsg nsentctlmsg nsentdatamsg - recvctlmsg: - capi messages received without DATA_B3_IND - recvdatamsg: - capi DATA_B3_IND received - sentctlmsg: - capi messages sent without DATA_B3_REQ - sentdatamsg: - capi DATA_B3_REQ sent - - for example:: - - 1 2057 1699 1721 1699 - -/proc/capi/capi20: statistics of capi.o (/dev/capi20) - minor nopen nrecvdropmsg nrecvctlmsg nrecvdatamsg sentctlmsg sentdatamsg - minor: - minor device number of capi device - nopen: - number of calls to devices open - nrecvdropmsg: - capi messages dropped (messages in recvqueue in close) - nrecvctlmsg: - capi messages received without DATA_B3_IND - nrecvdatamsg: - capi DATA_B3_IND received - nsentctlmsg: - capi messages sent without DATA_B3_REQ - nsentdatamsg: - capi DATA_B3_REQ sent - - for example:: - - 1 2 18 0 16 2 - -/proc/capi/capidrv: statistics of capidrv.o (capi messages) - nrecvctlmsg nrecvdatamsg sentctlmsg sentdatamsg - nrecvctlmsg: - capi messages received without DATA_B3_IND - nrecvdatamsg: - capi DATA_B3_IND received - nsentctlmsg: - capi messages sent without DATA_B3_REQ - nsentdatamsg: - capi DATA_B3_REQ sent - - for example: - 2780 2226 2256 2226 - -/proc/capi/controller: - controller drivername state cardname controllerinfo - - for example:: - - 1 b1pci running b1pci-e000 B1 3.07-01 0xe000 19 - 2 t1isa running t1isa-450 B1 3.07-01 0x450 11 0 - 3 b1pcmcia running m2-150 B1 3.07-01 0x150 5 - -/proc/capi/contrstats: - controller nrecvctlmsg nrecvdatamsg sentctlmsg sentdatamsg - nrecvctlmsg: - capi messages received without DATA_B3_IND - nrecvdatamsg: - capi DATA_B3_IND received - nsentctlmsg: - capi messages sent without DATA_B3_REQ - nsentdatamsg: - capi DATA_B3_REQ sent - - for example:: - - 1 2845 2272 2310 2274 - 2 2 0 2 0 - 3 2 0 2 0 - -/proc/capi/driver: - drivername ncontroller - - for example:: - - b1pci 1 - t1isa 1 - b1pcmcia 1 - b1isa 0 - -/proc/capi/ncci: - apllid ncci winsize sendwindow - - for example:: - - 1 0x10101 8 0 - -/proc/capi/users: kernelmodules that use the kernelcapi. - name - - for example:: - - capidrv - capi20 - -Questions ---------- - -Check out the FAQ (ftp.isdn4linux.de) or subscribe to the -linux-avmb1@calle.in-berlin.de mailing list by sending -a mail to majordomo@calle.in-berlin.de with -subscribe linux-avmb1 -in the body. - -German documentation and several scripts can be found at -ftp://ftp.avm.de/cardware/b1/linux/ - -Bugs ----- - -If you find any please let me know. - -Enjoy, - -Carsten Paeth (calle@calle.in-berlin.de) diff --git a/Documentation/isdn/gigaset.rst b/Documentation/isdn/gigaset.rst deleted file mode 100644 index 98b4ec521c51..000000000000 --- a/Documentation/isdn/gigaset.rst +++ /dev/null @@ -1,465 +0,0 @@ -========================== -GigaSet 307x Device Driver -========================== - -1. Requirements -================= - -1.1. Hardware -------------- - - This driver supports the connection of the Gigaset 307x/417x family of - ISDN DECT bases via Gigaset M101 Data, Gigaset M105 Data or direct USB - connection. The following devices are reported to be compatible: - - Bases: - - Siemens Gigaset 3070/3075 isdn - - Siemens Gigaset 4170/4175 isdn - - Siemens Gigaset SX205/255 - - Siemens Gigaset SX353 - - T-Com Sinus 45 [AB] isdn - - T-Com Sinus 721X[A] [SE] - - Vox Chicago 390 ISDN (KPN Telecom) - - RS232 data boxes: - - Siemens Gigaset M101 Data - - T-Com Sinus 45 Data 1 - - USB data boxes: - - Siemens Gigaset M105 Data - - Siemens Gigaset USB Adapter DECT - - T-Com Sinus 45 Data 2 - - T-Com Sinus 721 data - - Chicago 390 USB (KPN) - - See also http://www.erbze.info/sinus_gigaset.htm - (archived at https://web.archive.org/web/20100717020421/http://www.erbze.info:80/sinus_gigaset.htm ) and - http://gigaset307x.sourceforge.net/ - - We had also reports from users of Gigaset M105 who could use the drivers - with SX 100 and CX 100 ISDN bases (only in unimodem mode, see section 2.5.) - If you have another device that works with our driver, please let us know. - - Chances of getting an USB device to work are good if the output of:: - - lsusb - - at the command line contains one of the following:: - - ID 0681:0001 - ID 0681:0002 - ID 0681:0009 - ID 0681:0021 - ID 0681:0022 - -1.2. Software -------------- - - The driver works with the Kernel CAPI subsystem and can be used with any - software which is able to use CAPI 2.0 for ISDN connections (voice or data). - - There are some user space tools available at - https://sourceforge.net/projects/gigaset307x/ - which provide access to additional device specific functions like SMS, - phonebook or call journal. - - -2. How to use the driver -========================== - -2.1. Modules ------------- - - For the devices to work, the proper kernel modules have to be loaded. - This normally happens automatically when the system detects the USB - device (base, M105) or when the line discipline is attached (M101). It - can also be triggered manually using the modprobe(8) command, for example - for troubleshooting or to pass module parameters. - - The module ser_gigaset provides a serial line discipline N_GIGASET_M101 - which uses the regular serial port driver to access the device, and must - therefore be attached to the serial device to which the M101 is connected. - The ldattach(8) command (included in util-linux-ng release 2.14 or later) - can be used for that purpose, for example:: - - ldattach GIGASET_M101 /dev/ttyS1 - - This will open the device file, attach the line discipline to it, and - then sleep in the background, keeping the device open so that the line - discipline remains active. To deactivate it, kill the daemon, for example - with:: - - killall ldattach - - before disconnecting the device. To have this happen automatically at - system startup/shutdown on an LSB compatible system, create and activate - an appropriate LSB startup script /etc/init.d/gigaset. (The init name - 'gigaset' is officially assigned to this project by LANANA.) - Alternatively, just add the 'ldattach' command line to /etc/rc.local. - - The modules accept the following parameters: - - =============== ========== ========================================== - Module Parameter Meaning - - gigaset debug debug level (see section 3.2.) - - startmode initial operation mode (see section 2.5.): - bas_gigaset ) 1=CAPI (default), 0=Unimodem - ser_gigaset ) - usb_gigaset ) cidmode initial Call-ID mode setting (see section - 2.5.): 1=on (default), 0=off - - =============== ========== ========================================== - - Depending on your distribution you may want to create a separate module - configuration file like /etc/modprobe.d/gigaset.conf for these. - -2.2. Device nodes for user space programs ------------------------------------------ - - The device can be accessed from user space (eg. by the user space tools - mentioned in 1.2.) through the device nodes: - - - /dev/ttyGS0 for M101 (RS232 data boxes) - - /dev/ttyGU0 for M105 (USB data boxes) - - /dev/ttyGB0 for the base driver (direct USB connection) - - If you connect more than one device of a type, they will get consecutive - device nodes, eg. /dev/ttyGU1 for a second M105. - - You can also set a "default device" for the user space tools to use when - no device node is given as parameter, by creating a symlink /dev/ttyG to - one of them, eg.:: - - ln -s /dev/ttyGB0 /dev/ttyG - - The devices accept the following device specific ioctl calls - (defined in gigaset_dev.h): - - ``ioctl(int fd, GIGASET_REDIR, int *cmd);`` - - If cmd==1, the device is set to be controlled exclusively through the - character device node; access from the ISDN subsystem is blocked. - - If cmd==0, the device is set to be used from the ISDN subsystem and does - not communicate through the character device node. - - ``ioctl(int fd, GIGASET_CONFIG, int *cmd);`` - - (ser_gigaset and usb_gigaset only) - - If cmd==1, the device is set to adapter configuration mode where commands - are interpreted by the M10x DECT adapter itself instead of being - forwarded to the base station. In this mode, the device accepts the - commands described in Siemens document "AT-Kommando Alignment M10x Data" - for setting the operation mode, associating with a base station and - querying parameters like field strengh and signal quality. - - Note that there is no ioctl command for leaving adapter configuration - mode and returning to regular operation. In order to leave adapter - configuration mode, write the command ATO to the device. - - ``ioctl(int fd, GIGASET_BRKCHARS, unsigned char brkchars[6]);`` - - (usb_gigaset only) - - Set the break characters on an M105's internal serial adapter to the six - bytes stored in brkchars[]. Unused bytes should be set to zero. - - ioctl(int fd, GIGASET_VERSION, unsigned version[4]); - Retrieve version information from the driver. version[0] must be set to - one of: - - - GIGVER_DRIVER: retrieve driver version - - GIGVER_COMPAT: retrieve interface compatibility version - - GIGVER_FWBASE: retrieve the firmware version of the base - - Upon return, version[] is filled with the requested version information. - -2.3. CAPI ---------- - - The devices will show up as CAPI controllers as soon as the - corresponding driver module is loaded, and can then be used with - CAPI 2.0 kernel and user space applications. For user space access, - the module capi.ko must be loaded. - - Most distributions handle loading and unloading of the various CAPI - modules automatically via the command capiinit(1) from the capi4k-utils - package or a similar mechanism. Note that capiinit(1) cannot unload the - Gigaset drivers because it doesn't support more than one module per - driver. - -2.5. Unimodem mode ------------------- - - In this mode the device works like a modem connected to a serial port - (the /dev/ttyGU0, ... mentioned above) which understands the commands:: - - ATZ init, reset - => OK or ERROR - ATD - ATDT dial - => OK, CONNECT, - BUSY, - NO DIAL TONE, - NO CARRIER, - NO ANSWER - <pause>+++<pause> change to command mode when connected - ATH hangup - - You can use some configuration tool of your distribution to configure this - "modem" or configure pppd/wvdial manually. There are some example ppp - configuration files and chat scripts in the gigaset-VERSION/ppp directory - in the driver packages from https://sourceforge.net/projects/gigaset307x/. - Please note that the USB drivers are not able to change the state of the - control lines. This means you must use "Stupid Mode" if you are using - wvdial or you should use the nocrtscts option of pppd. - You must also assure that the ppp_async module is loaded with the parameter - flag_time=0. You can do this e.g. by adding a line like:: - - options ppp_async flag_time=0 - - to an appropriate module configuration file, like:: - - /etc/modprobe.d/gigaset.conf. - - Unimodem mode is needed for making some devices [e.g. SX100] work which - do not support the regular Gigaset command set. If debug output (see - section 3.2.) shows something like this when dialing:: - - CMD Received: ERROR - Available Params: 0 - Connection State: 0, Response: -1 - gigaset_process_response: resp_code -1 in ConState 0 ! - Timeout occurred - - then switching to unimodem mode may help. - - If you have installed the command line tool gigacontr, you can enter - unimodem mode using:: - - gigacontr --mode unimodem - - You can switch back using:: - - gigacontr --mode isdn - - You can also put the driver directly into Unimodem mode when it's loaded, - by passing the module parameter startmode=0 to the hardware specific - module, e.g.:: - - modprobe usb_gigaset startmode=0 - - or by adding a line like:: - - options usb_gigaset startmode=0 - - to an appropriate module configuration file, like:: - - /etc/modprobe.d/gigaset.conf - -2.6. Call-ID (CID) mode ------------------------ - - Call-IDs are numbers used to tag commands to, and responses from, the - Gigaset base in order to support the simultaneous handling of multiple - ISDN calls. Their use can be enabled ("CID mode") or disabled ("Unimodem - mode"). Without Call-IDs (in Unimodem mode), only a very limited set of - functions is available. It allows outgoing data connections only, but - does not signal incoming calls or other base events. - - DECT cordless data devices (M10x) permanently occupy the cordless - connection to the base while Call-IDs are activated. As the Gigaset - bases only support one DECT data connection at a time, this prevents - other DECT cordless data devices from accessing the base. - - During active operation, the driver switches to the necessary mode - automatically. However, for the reasons above, the mode chosen when - the device is not in use (idle) can be selected by the user. - - - If you want to receive incoming calls, you can use the default - settings (CID mode). - - If you have several DECT data devices (M10x) which you want to use - in turn, select Unimodem mode by passing the parameter "cidmode=0" to - the appropriate driver module (ser_gigaset or usb_gigaset). - - If you want both of these at once, you are out of luck. - - You can also use the tty class parameter "cidmode" of the device to - change its CID mode while the driver is loaded, eg.:: - - echo 0 > /sys/class/tty/ttyGU0/cidmode - -2.7. Dialing Numbers --------------------- -provided by an application for dialing out must - be a public network number according to the local dialing plan, without - any dial prefix for getting an outside line. - - Internal calls can be made by providing an internal extension number - prefixed with ``**`` (two asterisks) as the called party number. So to dial - eg. the first registered DECT handset, give ``**11`` as the called party - number. Dialing ``***`` (three asterisks) calls all extensions - simultaneously (global call). - - Unimodem mode does not support internal calls. - -2.8. Unregistered Wireless Devices (M101/M105) ----------------------------------------------- - - The main purpose of the ser_gigaset and usb_gigaset drivers is to allow - the M101 and M105 wireless devices to be used as ISDN devices for ISDN - connections through a Gigaset base. Therefore they assume that the device - is registered to a DECT base. - - If the M101/M105 device is not registered to a base, initialization of - the device fails, and a corresponding error message is logged by the - driver. In that situation, a restricted set of functions is available - which includes, in particular, those necessary for registering the device - to a base or for switching it between Fixed Part and Portable Part - modes. See the gigacontr(8) manpage for details. - -3. Troubleshooting -==================== - -3.1. Solutions to frequently reported problems ----------------------------------------------- - - Problem: - You have a slow provider and isdn4linux gives up dialing too early. - Solution: - Load the isdn module using the dialtimeout option. You can do this e.g. - by adding a line like:: - - options isdn dialtimeout=15 - - to /etc/modprobe.d/gigaset.conf or a similar file. - - Problem: - The isdnlog program emits error messages or just doesn't work. - Solution: - Isdnlog supports only the HiSax driver. Do not attempt to use it with - other drivers such as Gigaset. - - Problem: - You have two or more DECT data adapters (M101/M105) and only the - first one you turn on works. - Solution: - Select Unimodem mode for all DECT data adapters. (see section 2.5.) - - Problem: - Messages like this:: - - usb_gigaset 3-2:1.0: Could not initialize the device. - - appear in your syslog. - Solution: - Check whether your M10x wireless device is correctly registered to the - Gigaset base. (see section 2.7.) - -3.2. Telling the driver to provide more information ---------------------------------------------------- - Building the driver with the "Gigaset debugging" kernel configuration - option (CONFIG_GIGASET_DEBUG) gives it the ability to produce additional - information useful for debugging. - - You can control the amount of debugging information the driver produces by - writing an appropriate value to /sys/module/gigaset/parameters/debug, - e.g.:: - - echo 0 > /sys/module/gigaset/parameters/debug - - switches off debugging output completely, - - :: - - echo 0x302020 > /sys/module/gigaset/parameters/debug - - enables a reasonable set of debugging output messages. These values are - bit patterns where every bit controls a certain type of debugging output. - See the constants DEBUG_* in the source file gigaset.h for details. - - The initial value can be set using the debug parameter when loading the - module "gigaset", e.g. by adding a line:: - - options gigaset debug=0 - - to your module configuration file, eg. /etc/modprobe.d/gigaset.conf - - Generated debugging information can be found - - as output of the command:: - - dmesg - - - in system log files written by your syslog daemon, usually - in /var/log/, e.g. /var/log/messages. - -3.3. Reporting problems and bugs --------------------------------- - If you can't solve problems with the driver on your own, feel free to - use one of the forums, bug trackers, or mailing lists on - - https://sourceforge.net/projects/gigaset307x - - or write an electronic mail to the maintainers. - - Try to provide as much information as possible, such as - - - distribution - - kernel version (uname -r) - - gcc version (gcc --version) - - hardware architecture (uname -m, ...) - - type and firmware version of your device (base and wireless module, - if any) - - output of "lsusb -v" (if using an USB device) - - error messages - - relevant system log messages (it would help if you activate debug - output as described in 3.2.) - - For help with general configuration problems not specific to our driver, - such as isdn4linux and network configuration issues, please refer to the - appropriate forums and newsgroups. - -3.4. Reporting problem solutions --------------------------------- - If you solved a problem with our drivers, wrote startup scripts for your - distribution, ... feel free to contact us (using one of the places - mentioned in 3.3.). We'd like to add scripts, hints, documentation - to the driver and/or the project web page. - - -4. Links, other software -========================== - - - Sourceforge project developing this driver and associated tools - https://sourceforge.net/projects/gigaset307x - - Yahoo! Group on the Siemens Gigaset family of devices - https://de.groups.yahoo.com/group/Siemens-Gigaset - - Siemens Gigaset/T-Sinus compatibility table - http://www.erbze.info/sinus_gigaset.htm - (archived at https://web.archive.org/web/20100717020421/http://www.erbze.info:80/sinus_gigaset.htm ) - - -5. Credits -============ - - Thanks to - - Karsten Keil - for his help with isdn4linux - Deti Fliegl - for his base driver code - Dennis Dietrich - for his kernel 2.6 patches - Andreas Rummel - for his work and logs to get unimodem mode working - Andreas Degert - for his logs and patches to get cx 100 working - Dietrich Feist - for his generous donation of one M105 and two M101 cordless adapters - Christoph Schweers - for his generous donation of a M34 device - - and all the other people who sent logs and other information. diff --git a/Documentation/isdn/hysdn.rst b/Documentation/isdn/hysdn.rst deleted file mode 100644 index 0a168d1cbffc..000000000000 --- a/Documentation/isdn/hysdn.rst +++ /dev/null @@ -1,196 +0,0 @@ -============ -Hysdn Driver -============ - -The hysdn driver has been written by -Werner Cornelius (werner@isdn4linux.de or werner@titro.de) -for Hypercope GmbH Aachen Germany. Hypercope agreed to publish this driver -under the GNU General Public License. - -The CAPI 2.0-support was added by Ulrich Albrecht (ualbrecht@hypercope.de) -for Hypercope GmbH Aachen, Germany. - - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; either version 2 of the License, or - (at your option) any later version. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. - -.. Table of contents - - 1. About the driver - - 2. Loading/Unloading the driver - - 3. Entries in the /proc filesystem - - 4. The /proc/net/hysdn/cardconfX file - - 5. The /proc/net/hysdn/cardlogX file - - 6. Where to get additional info and help - - -1. About the driver -=================== - - The drivers/isdn/hysdn subdir contains a driver for HYPERCOPEs active - PCI isdn cards Champ, Ergo and Metro. To enable support for this cards - enable ISDN support in the kernel config and support for HYSDN cards in - the active cards submenu. The driver may only be compiled and used if - support for loadable modules and the process filesystem have been enabled. - - These cards provide two different interfaces to the kernel. Without the - optional CAPI 2.0 support, they register as ethernet card. IP-routing - to a ISDN-destination is performed on the card itself. All necessary - handlers for various protocols like ppp and others as well as config info - and firmware may be fetched from Hypercopes WWW-Site www.hypercope.de. - - With CAPI 2.0 support enabled, the card can also be used as a CAPI 2.0 - compliant devices with either CAPI 2.0 applications - (check isdn4k-utils) or -using the capidrv module- as a regular - isdn4linux device. This is done via the same mechanism as with the - active AVM cards and in fact uses the same module. - - -2. Loading/Unloading the driver -=============================== - - The module has no command line parameters and auto detects up to 10 cards - in the id-range 0-9. - If a loaded driver shall be unloaded all open files in the /proc/net/hysdn - subdir need to be closed and all ethernet interfaces allocated by this - driver must be shut down. Otherwise the module counter will avoid a module - unload. - - If you are using the CAPI 2.0-interface, make sure to load/modprobe the - kernelcapi-module first. - - If you plan to use the capidrv-link to isdn4linux, make sure to load - capidrv.o after all modules using this driver (i.e. after hysdn and - any avm-specific modules). - -3. Entries in the /proc filesystem -================================== - - When the module has been loaded it adds the directory hysdn in the - /proc/net tree. This directory contains exactly 2 file entries for each - card. One is called cardconfX and the other cardlogX, where X is the - card id number from 0 to 9. - The cards are numbered in the order found in the PCI config data. - -4. The /proc/net/hysdn/cardconfX file -===================================== - - This file may be read to get by everyone to get info about the cards type, - actual state, available features and used resources. - The first 3 entries (id, bus and slot) are PCI info fields, the following - type field gives the information about the cards type: - - - 4 -> Ergo card (server card with 2 b-chans) - - 5 -> Metro card (server card with 4 or 8 b-chans) - - 6 -> Champ card (client card with 2 b-chans) - - The following 3 fields show the hardware assignments for irq, iobase and the - dual ported memory (dp-mem). - - The fields b-chans and fax-chans announce the available card resources of - this types for the user. - - The state variable indicates the actual drivers state for this card with the - following assignments. - - - 0 -> card has not been booted since driver load - - 1 -> card booting is actually in progess - - 2 -> card is in an error state due to a previous boot failure - - 3 -> card is booted and active - - And the last field (device) shows the name of the ethernet device assigned - to this card. Up to the first successful boot this field only shows a - - to tell that no net device has been allocated up to now. Once a net device - has been allocated it remains assigned to this card, even if a card is - rebooted and an boot error occurs. - - Writing to the cardconfX file boots the card or transfers config lines to - the cards firmware. The type of data is automatically detected when the - first data is written. Only root has write access to this file. - The firmware boot files are normally called hyclient.pof for client cards - and hyserver.pof for server cards. - After successfully writing the boot file, complete config files or single - config lines may be copied to this file. - If an error occurs the return value given to the writing process has the - following additional codes (decimal): - - ==== ============================================ - 1000 Another process is currently bootng the card - 1001 Invalid firmware header - 1002 Boards dual-port RAM test failed - 1003 Internal firmware handler error - 1004 Boot image size invalid - 1005 First boot stage (bootstrap loader) failed - 1006 Second boot stage failure - 1007 Timeout waiting for card ready during boot - 1008 Operation only allowed in booted state - 1009 Config line too long - 1010 Invalid channel number - 1011 Timeout sending config data - ==== ============================================ - - Additional info about error reasons may be fetched from the log output. - -5. The /proc/net/hysdn/cardlogX file -==================================== - - The cardlogX file entry may be opened multiple for reading by everyone to - get the cards and drivers log data. Card messages always start with the - keyword LOG. All other lines are output from the driver. - The driver log data may be redirected to the syslog by selecting the - appropriate bitmask. The cards log messages will always be send to this - interface but never to the syslog. - - A root user may write a decimal or hex (with 0x) value t this file to select - desired output options. As mentioned above the cards log dat is always - written to the cardlog file independent of the following options only used - to check and debug the driver itself: - - For example:: - - echo "0x34560078" > /proc/net/hysdn/cardlog0 - - to output the hex log mask 34560078 for card 0. - - The written value is regarded as an unsigned 32-Bit value, bit ored for - desired output. The following bits are already assigned: - - ========== ============================================================ - 0x80000000 All driver log data is alternatively via syslog - 0x00000001 Log memory allocation errors - 0x00000010 Firmware load start and close are logged - 0x00000020 Log firmware record parser - 0x00000040 Log every firmware write actions - 0x00000080 Log all card related boot messages - 0x00000100 Output all config data sent for debugging purposes - 0x00000200 Only non comment config lines are shown wth channel - 0x00000400 Additional conf log output - 0x00001000 Log the asynchronous scheduler actions (config and log) - 0x00100000 Log all open and close actions to /proc/net/hysdn/card files - 0x00200000 Log all actions from /proc file entries - 0x00010000 Log network interface init and deinit - ========== ============================================================ - -6. Where to get additional info and help -======================================== - - If you have any problems concerning the driver or configuration contact - the Hypercope support team (support@hypercope.de) and or the authors - Werner Cornelius (werner@isdn4linux or cornelius@titro.de) or - Ulrich Albrecht (ualbrecht@hypercope.de). diff --git a/Documentation/isdn/index.rst b/Documentation/isdn/index.rst index 407e74b78372..9622939fa526 100644 --- a/Documentation/isdn/index.rst +++ b/Documentation/isdn/index.rst @@ -9,9 +9,6 @@ ISDN interface_capi - avmb1 - gigaset - hysdn m_isdn credits diff --git a/Documentation/isdn/interface_capi.rst b/Documentation/isdn/interface_capi.rst index 01a4b5ade9a4..fe2421444b76 100644 --- a/Documentation/isdn/interface_capi.rst +++ b/Documentation/isdn/interface_capi.rst @@ -26,13 +26,6 @@ This standard is freely available from https://www.capi.org. 2. Driver and Device Registration ================================= -CAPI drivers optionally register themselves with Kernel CAPI by calling the -Kernel CAPI function register_capi_driver() with a pointer to a struct -capi_driver. This structure must be filled with the name and revision of the -driver, and optionally a pointer to a callback function, add_card(). The -registration can be revoked by calling the function unregister_capi_driver() -with a pointer to the same struct capi_driver. - CAPI drivers must register each of the ISDN devices they control with Kernel CAPI by calling the Kernel CAPI function attach_capi_ctr() with a pointer to a struct capi_ctr before they can be used. This structure must be filled with @@ -89,9 +82,6 @@ register_capi_driver(): the name of the driver, as a zero-terminated ASCII string ``char revision[32]`` the revision number of the driver, as a zero-terminated ASCII string -``int (*add_card)(struct capi_driver *driver, capicardparams *data)`` - a callback function pointer (may be NULL) - 4.2 struct capi_ctr ------------------- @@ -178,12 +168,6 @@ to be set by the driver before calling attach_capi_ctr(): pointer to a callback function returning the entry for the device in the CAPI controller info table, /proc/capi/controller -``const struct file_operations *proc_fops`` - pointers to callback functions for the device's proc file - system entry, /proc/capi/controllers/<n>; pointer to the device's - capi_ctr structure is available from struct proc_dir_entry::data - which is available from struct inode. - Note: Callback functions except send_message() are never called in interrupt context. @@ -267,25 +251,10 @@ _cmstruct alternative representation for CAPI parameters of type 'struct' _cmsg structure members. =========== ================================================================= -Functions capi_cmsg2message() and capi_message2cmsg() are provided to convert -messages between their transport encoding described in the CAPI 2.0 standard -and their _cmsg structure representation. Note that capi_cmsg2message() does -not know or check the size of its destination buffer. The caller must make -sure it is big enough to accommodate the resulting CAPI message. - 5. Lower Layer Interface Functions ================================== -(declared in <linux/isdn/capilli.h>) - -:: - - void register_capi_driver(struct capi_driver *drvr) - void unregister_capi_driver(struct capi_driver *drvr) - -register/unregister a driver with Kernel CAPI - :: int attach_capi_ctr(struct capi_ctr *ctrlr) @@ -302,13 +271,6 @@ signal controller ready/not ready :: - void capi_ctr_suspend_output(struct capi_ctr *ctrlr) - void capi_ctr_resume_output(struct capi_ctr *ctrlr) - -signal suspend/resume - -:: - void capi_ctr_handle_message(struct capi_ctr * ctrlr, u16 applid, struct sk_buff *skb) @@ -319,21 +281,6 @@ for forwarding to the specified application 6. Helper Functions and Macros ============================== -Library functions (from <linux/isdn/capilli.h>): - -:: - - void capilib_new_ncci(struct list_head *head, u16 applid, - u32 ncci, u32 winsize) - void capilib_free_ncci(struct list_head *head, u16 applid, u32 ncci) - void capilib_release_appl(struct list_head *head, u16 applid) - void capilib_release(struct list_head *head) - void capilib_data_b3_conf(struct list_head *head, u16 applid, - u32 ncci, u16 msgid) - u16 capilib_data_b3_req(struct list_head *head, u16 applid, - u32 ncci, u16 msgid) - - Macros to extract/set element values from/in a CAPI message header (from <linux/isdn/capiutil.h>): @@ -357,24 +304,6 @@ CAPIMSG_DATALEN(m) CAPIMSG_SETDATALEN(m, len) Data Length (u16) Library functions for working with _cmsg structures (from <linux/isdn/capiutil.h>): -``unsigned capi_cmsg2message(_cmsg *cmsg, u8 *msg)`` - Assembles a CAPI 2.0 message from the parameters in ``*cmsg``, - storing the result in ``*msg``. - -``unsigned capi_message2cmsg(_cmsg *cmsg, u8 *msg)`` - Disassembles the CAPI 2.0 message in ``*msg``, storing the parameters - in ``*cmsg``. - -``unsigned capi_cmsg_header(_cmsg *cmsg, u16 ApplId, u8 Command, u8 Subcommand, u16 Messagenumber, u32 Controller)`` - Fills the header part and address field of the _cmsg structure ``*cmsg`` - with the given values, zeroing the remainder of the structure so only - parameters with non-default values need to be changed before sending - the message. - -``void capi_cmsg_answer(_cmsg *cmsg)`` - Sets the low bit of the Subcommand field in ``*cmsg``, thereby - converting ``_REQ`` to ``_CONF`` and ``_IND`` to ``_RESP``. - ``char *capi_cmd2str(u8 Command, u8 Subcommand)`` Returns the CAPI 2.0 message name corresponding to the given command and subcommand values, as a static ASCII string. The return value may diff --git a/Documentation/userspace-api/ioctl/ioctl-number.rst b/Documentation/userspace-api/ioctl/ioctl-number.rst index 4ef86433bd67..2e91370dc159 100644 --- a/Documentation/userspace-api/ioctl/ioctl-number.rst +++ b/Documentation/userspace-api/ioctl/ioctl-number.rst @@ -132,7 +132,6 @@ Code Seq# Include File Comments 'F' 80-8F linux/arcfb.h conflict! 'F' DD video/sstfb.h conflict! 'G' 00-3F drivers/misc/sgi-gru/grulib.h conflict! -'G' 00-0F linux/gigaset_dev.h conflict! 'H' 00-7F linux/hiddev.h conflict! 'H' 00-0F linux/hidraw.h conflict! 'H' 01 linux/mei.h conflict! diff --git a/MAINTAINERS b/MAINTAINERS index 5590daffdb5a..eb2ea59932b9 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -674,6 +674,14 @@ S: Maintained F: Documentation/i2c/busses/i2c-ali1563.rst F: drivers/i2c/busses/i2c-ali1563.c +ALL SENSORS DLH SERIES PRESSURE SENSORS DRIVER +M: Tomislav Denis <tomislav.denis@avl.com> +W: http://www.allsensors.com/ +S: Maintained +L: linux-iio@vger.kernel.org +F: drivers/iio/pressure/dlhl60d.c +F: Documentation/devicetree/bindings/iio/pressure/asc,dlhl60d.yaml + ALLEGRO DVT VIDEO IP CORE DRIVER M: Michael Tretter <m.tretter@pengutronix.de> R: Pengutronix Kernel Team <kernel@pengutronix.de> @@ -907,6 +915,14 @@ S: Supported F: drivers/iio/dac/ad5758.c F: Documentation/devicetree/bindings/iio/dac/ad5758.txt +ANALOG DEVICES INC AD7091R5 DRIVER +M: Beniamin Bia <beniamin.bia@analog.com> +L: linux-iio@vger.kernel.org +W: http://ez.analog.com/community/linux-device-drivers +S: Supported +F: drivers/iio/adc/ad7091r5.c +F: Documentation/devicetree/bindings/iio/adc/adi,ad7091r5.yaml + ANALOG DEVICES INC AD7124 DRIVER M: Stefan Popa <stefan.popa@analog.com> L: linux-iio@vger.kernel.org @@ -1061,7 +1077,7 @@ S: Supported F: Documentation/ABI/testing/sysfs-bus-iio-frequency-ad9523 F: Documentation/ABI/testing/sysfs-bus-iio-frequency-adf4350 F: drivers/iio/*/ad* -F: drivers/iio/adc/ltc2497* +F: drivers/iio/adc/ltc249* X: drivers/iio/*/adjd* F: drivers/staging/iio/*/ad* @@ -3116,6 +3132,13 @@ S: Supported F: drivers/net/bonding/ F: include/uapi/linux/if_bonding.h +BOSCH SENSORTEC BMA400 ACCELEROMETER IIO DRIVER +M: Dan Robertson <dan@dlrobertson.com> +L: linux-iio@vger.kernel.org +S: Maintained +F: drivers/iio/accel/bma400* +F: Documentation/devicetree/bindings/iio/accel/bosch,bma400.yaml + BPF (Safe dynamic programs and tools) M: Alexei Starovoitov <ast@kernel.org> M: Daniel Borkmann <daniel@iogearbox.net> @@ -8862,7 +8885,7 @@ S: Maintained F: drivers/isdn/mISDN F: drivers/isdn/hardware -ISDN/CAPI SUBSYSTEM +ISDN/CMTP OVER BLUETOOTH M: Karsten Keil <isdn@linux-pingi.de> L: isdn4linux@listserv.isdn4linux.de (subscribers-only) L: netdev@vger.kernel.org @@ -8870,7 +8893,6 @@ W: http://www.isdn4linux.de S: Odd Fixes F: Documentation/isdn/ F: drivers/isdn/capi/ -F: drivers/staging/isdn/ F: net/bluetooth/cmtp/ F: include/linux/isdn/ F: include/uapi/linux/isdn/ @@ -12528,6 +12550,13 @@ L: platform-driver-x86@vger.kernel.org S: Maintained F: drivers/platform/x86/panasonic-laptop.c +PARALLAX PING IIO SENSOR DRIVER +M: Andreas Klinger <ak@it-klinger.de> +L: linux-iio@vger.kernel.org +S: Maintained +F: Documentation/devicetree/bindings/iio/proximity/parallax-ping.yaml +F: drivers/iio/proximity/ping.c + PARALLEL LCD/KEYPAD PANEL DRIVER M: Willy Tarreau <willy@haproxy.com> M: Ksenija Stanojevic <ksenija.stanojevic@gmail.com> diff --git a/drivers/iio/accel/Kconfig b/drivers/iio/accel/Kconfig index d4ef35aeb579..5d91a6dda894 100644 --- a/drivers/iio/accel/Kconfig +++ b/drivers/iio/accel/Kconfig @@ -89,13 +89,13 @@ config ADXL372_I2C module will be called adxl372_i2c. config BMA180 - tristate "Bosch BMA180/BMA250 3-Axis Accelerometer Driver" + tristate "Bosch BMA180/BMA25x 3-Axis Accelerometer Driver" depends on I2C select IIO_BUFFER select IIO_TRIGGERED_BUFFER help Say Y here if you want to build a driver for the Bosch BMA180 or - BMA250 triaxial acceleration sensor. + BMA25x triaxial acceleration sensor. To compile this driver as a module, choose M here: the module will be called bma180. @@ -112,6 +112,22 @@ config BMA220 To compile this driver as a module, choose M here: the module will be called bma220_spi. +config BMA400 + tristate "Bosch BMA400 3-Axis Accelerometer Driver" + select REGMAP + select BMA400_I2C if I2C + help + Say Y here if you want to build a driver for the Bosch BMA400 + triaxial acceleration sensor. + + To compile this driver as a module, choose M here: the + module will be called bma400_core and you will also get + bma400_i2c if I2C is enabled. + +config BMA400_I2C + tristate + depends on BMA400 + config BMC150_ACCEL tristate "Bosch BMC150 Accelerometer Driver" select IIO_BUFFER diff --git a/drivers/iio/accel/Makefile b/drivers/iio/accel/Makefile index 56bd0215e0d4..3a051cf37f40 100644 --- a/drivers/iio/accel/Makefile +++ b/drivers/iio/accel/Makefile @@ -14,6 +14,8 @@ obj-$(CONFIG_ADXL372_I2C) += adxl372_i2c.o obj-$(CONFIG_ADXL372_SPI) += adxl372_spi.o obj-$(CONFIG_BMA180) += bma180.o obj-$(CONFIG_BMA220) += bma220_spi.o +obj-$(CONFIG_BMA400) += bma400_core.o +obj-$(CONFIG_BMA400_I2C) += bma400_i2c.o obj-$(CONFIG_BMC150_ACCEL) += bmc150-accel-core.o obj-$(CONFIG_BMC150_ACCEL_I2C) += bmc150-accel-i2c.o obj-$(CONFIG_BMC150_ACCEL_SPI) += bmc150-accel-spi.o diff --git a/drivers/iio/accel/adis16201.c b/drivers/iio/accel/adis16201.c index c4810c73b2a2..0f0f27a8184e 100644 --- a/drivers/iio/accel/adis16201.c +++ b/drivers/iio/accel/adis16201.c @@ -233,6 +233,12 @@ static const char * const adis16201_status_error_msgs[] = { [ADIS16201_DIAG_STAT_POWER_LOW_BIT] = "Power supply below 2.975V", }; +static const struct adis_timeout adis16201_timeouts = { + .reset_ms = ADIS16201_STARTUP_DELAY_MS, + .sw_reset_ms = ADIS16201_STARTUP_DELAY_MS, + .self_test_ms = ADIS16201_STARTUP_DELAY_MS, +}; + static const struct adis_data adis16201_data = { .read_delay = 20, .msc_ctrl_reg = ADIS16201_MSC_CTRL_REG, @@ -241,7 +247,7 @@ static const struct adis_data adis16201_data = { .self_test_mask = ADIS16201_MSC_CTRL_SELF_TEST_EN, .self_test_no_autoclear = true, - .startup_delay = ADIS16201_STARTUP_DELAY_MS, + .timeouts = &adis16201_timeouts, .status_error_msgs = adis16201_status_error_msgs, .status_error_mask = BIT(ADIS16201_DIAG_STAT_SPI_FAIL_BIT) | diff --git a/drivers/iio/accel/adis16209.c b/drivers/iio/accel/adis16209.c index 98d77af8a2b0..c6dbd2424e10 100644 --- a/drivers/iio/accel/adis16209.c +++ b/drivers/iio/accel/adis16209.c @@ -243,6 +243,12 @@ static const char * const adis16209_status_error_msgs[] = { [ADIS16209_STAT_POWER_LOW_BIT] = "Power supply below 2.975V", }; +static const struct adis_timeout adis16209_timeouts = { + .reset_ms = ADIS16209_STARTUP_DELAY_MS, + .self_test_ms = ADIS16209_STARTUP_DELAY_MS, + .sw_reset_ms = ADIS16209_STARTUP_DELAY_MS, +}; + static const struct adis_data adis16209_data = { .read_delay = 30, .msc_ctrl_reg = ADIS16209_MSC_CTRL_REG, @@ -251,7 +257,7 @@ static const struct adis_data adis16209_data = { .self_test_mask = ADIS16209_MSC_CTRL_SELF_TEST_EN, .self_test_no_autoclear = true, - .startup_delay = ADIS16209_STARTUP_DELAY_MS, + .timeouts = &adis16209_timeouts, .status_error_msgs = adis16209_status_error_msgs, .status_error_mask = BIT(ADIS16209_STAT_SELFTEST_FAIL_BIT) | diff --git a/drivers/iio/accel/bma180.c b/drivers/iio/accel/bma180.c index 1574e4604a4f..fcd91d5f05fd 100644 --- a/drivers/iio/accel/bma180.c +++ b/drivers/iio/accel/bma180.c @@ -9,6 +9,7 @@ * SPI is not supported by driver * BMA180: 7-bit I2C slave address 0x40 or 0x41 * BMA250: 7-bit I2C slave address 0x18 or 0x19 + * BMA254: 7-bit I2C slave address 0x18 or 0x19 */ #include <linux/module.h> @@ -18,6 +19,7 @@ #include <linux/of_device.h> #include <linux/of.h> #include <linux/bitops.h> +#include <linux/regulator/consumer.h> #include <linux/slab.h> #include <linux/string.h> #include <linux/iio/iio.h> @@ -33,17 +35,20 @@ enum chip_ids { BMA180, BMA250, + BMA254, }; struct bma180_data; struct bma180_part_info { + u8 chip_id; const struct iio_chan_spec *channels; unsigned int num_channels; const int *scale_table; unsigned int num_scales; const int *bw_table; unsigned int num_bw; + int center_temp; u8 int_reset_reg, int_reset_mask; u8 sleep_reg, sleep_mask; @@ -51,6 +56,7 @@ struct bma180_part_info { u8 scale_reg, scale_mask; u8 power_reg, power_mask, lowpower_val; u8 int_enable_reg, int_enable_mask; + u8 int_map_reg, int_enable_dataready_int1_mask; u8 softreset_reg; int (*chip_config)(struct bma180_data *data); @@ -89,6 +95,8 @@ struct bma180_part_info { #define BMA180_RESET_VAL 0xb6 #define BMA180_ID_REG_VAL 0x03 +#define BMA250_ID_REG_VAL 0x03 +#define BMA254_ID_REG_VAL 0xfa /* 250 decimal */ /* Chip power modes */ #define BMA180_LOW_POWER 0x03 @@ -109,7 +117,26 @@ struct bma180_part_info { #define BMA250_INT1_DATA_MASK BIT(0) #define BMA250_INT_RESET_MASK BIT(7) /* Reset pending interrupts */ +#define BMA254_RANGE_REG 0x0f +#define BMA254_BW_REG 0x10 +#define BMA254_POWER_REG 0x11 +#define BMA254_RESET_REG 0x14 +#define BMA254_INT_ENABLE_REG 0x17 +#define BMA254_INT_MAP_REG 0x1a +#define BMA254_INT_RESET_REG 0x21 + +#define BMA254_RANGE_MASK GENMASK(3, 0) /* Range of accel values */ +#define BMA254_BW_MASK GENMASK(4, 0) /* Accel bandwidth */ +#define BMA254_SUSPEND_MASK BIT(7) /* chip will sleep */ +#define BMA254_LOWPOWER_MASK BIT(6) +#define BMA254_DATA_INTEN_MASK BIT(4) +#define BMA254_INT2_DATA_MASK BIT(7) +#define BMA254_INT1_DATA_MASK BIT(0) +#define BMA254_INT_RESET_MASK BIT(7) /* Reset pending interrupts */ + struct bma180_data { + struct regulator *vdd_supply; + struct regulator *vddio_supply; struct i2c_client *client; struct iio_trigger *trig; const struct bma180_part_info *part_info; @@ -132,8 +159,8 @@ enum bma180_chan { static int bma180_bw_table[] = { 10, 20, 40, 75, 150, 300 }; /* Hz */ static int bma180_scale_table[] = { 1275, 1863, 2452, 3727, 4903, 9709, 19417 }; -static int bma250_bw_table[] = { 8, 16, 31, 63, 125, 250 }; /* Hz */ -static int bma250_scale_table[] = { 0, 0, 0, 38344, 0, 76590, 0, 0, 153180, 0, +static int bma25x_bw_table[] = { 8, 16, 31, 63, 125, 250 }; /* Hz */ +static int bma25x_scale_table[] = { 0, 0, 0, 38344, 0, 76590, 0, 0, 153180, 0, 0, 0, 306458 }; static int bma180_get_data_reg(struct bma180_data *data, enum bma180_chan chan) @@ -307,8 +334,11 @@ static int bma180_chip_init(struct bma180_data *data) if (ret < 0) return ret; - if (ret != BMA180_ID_REG_VAL) + if (ret != data->part_info->chip_id) { + dev_err(&data->client->dev, "wrong chip ID %d expected %d\n", + ret, data->part_info->chip_id); return -ENODEV; + } ret = bma180_soft_reset(data); if (ret) @@ -355,7 +385,7 @@ err: return ret; } -static int bma250_chip_config(struct bma180_data *data) +static int bma25x_chip_config(struct bma180_data *data) { int ret = bma180_chip_init(data); @@ -367,8 +397,12 @@ static int bma250_chip_config(struct bma180_data *data) ret = bma180_set_scale(data, 38344); /* 2 G */ if (ret) goto err; - ret = bma180_set_bits(data, BMA250_INT_MAP_REG, - BMA250_INT1_DATA_MASK, 1); + /* + * This enables dataready interrupt on the INT1 pin + * FIXME: support using the INT2 pin + */ + ret = bma180_set_bits(data, data->part_info->int_map_reg, + data->part_info->int_enable_dataready_int1_mask, 1); if (ret) goto err; @@ -394,7 +428,7 @@ err: dev_err(&data->client->dev, "failed to disable the chip\n"); } -static void bma250_chip_disable(struct bma180_data *data) +static void bma25x_chip_disable(struct bma180_data *data) { if (bma180_set_new_data_intr_state(data, false)) goto err; @@ -497,7 +531,7 @@ static int bma180_read_raw(struct iio_dev *indio_dev, return -EINVAL; } case IIO_CHAN_INFO_OFFSET: - *val = 48; /* 0 LSB @ 24 degree C */ + *val = data->part_info->center_temp; return IIO_VAL_INT; default: return -EINVAL; @@ -627,34 +661,96 @@ static const struct iio_chan_spec bma250_channels[] = { IIO_CHAN_SOFT_TIMESTAMP(4), }; +static const struct iio_chan_spec bma254_channels[] = { + BMA180_ACC_CHANNEL(X, 12), + BMA180_ACC_CHANNEL(Y, 12), + BMA180_ACC_CHANNEL(Z, 12), + BMA180_TEMP_CHANNEL, + IIO_CHAN_SOFT_TIMESTAMP(4), +}; + static const struct bma180_part_info bma180_part_info[] = { [BMA180] = { - bma180_channels, ARRAY_SIZE(bma180_channels), - bma180_scale_table, ARRAY_SIZE(bma180_scale_table), - bma180_bw_table, ARRAY_SIZE(bma180_bw_table), - BMA180_CTRL_REG0, BMA180_RESET_INT, - BMA180_CTRL_REG0, BMA180_SLEEP, - BMA180_BW_TCS, BMA180_BW, - BMA180_OFFSET_LSB1, BMA180_RANGE, - BMA180_TCO_Z, BMA180_MODE_CONFIG, BMA180_LOW_POWER, - BMA180_CTRL_REG3, BMA180_NEW_DATA_INT, - BMA180_RESET, - bma180_chip_config, - bma180_chip_disable, + .chip_id = BMA180_ID_REG_VAL, + .channels = bma180_channels, + .num_channels = ARRAY_SIZE(bma180_channels), + .scale_table = bma180_scale_table, + .num_scales = ARRAY_SIZE(bma180_scale_table), + .bw_table = bma180_bw_table, + .num_bw = ARRAY_SIZE(bma180_bw_table), + .center_temp = 48, /* 0 LSB @ 24 degree C */ + .int_reset_reg = BMA180_CTRL_REG0, + .int_reset_mask = BMA180_RESET_INT, + .sleep_reg = BMA180_CTRL_REG0, + .sleep_mask = BMA180_SLEEP, + .bw_reg = BMA180_BW_TCS, + .bw_mask = BMA180_BW, + .scale_reg = BMA180_OFFSET_LSB1, + .scale_mask = BMA180_RANGE, + .power_reg = BMA180_TCO_Z, + .power_mask = BMA180_MODE_CONFIG, + .lowpower_val = BMA180_LOW_POWER, + .int_enable_reg = BMA180_CTRL_REG3, + .int_enable_mask = BMA180_NEW_DATA_INT, + .softreset_reg = BMA180_RESET, + .chip_config = bma180_chip_config, + .chip_disable = bma180_chip_disable, }, [BMA250] = { - bma250_channels, ARRAY_SIZE(bma250_channels), - bma250_scale_table, ARRAY_SIZE(bma250_scale_table), - bma250_bw_table, ARRAY_SIZE(bma250_bw_table), - BMA250_INT_RESET_REG, BMA250_INT_RESET_MASK, - BMA250_POWER_REG, BMA250_SUSPEND_MASK, - BMA250_BW_REG, BMA250_BW_MASK, - BMA250_RANGE_REG, BMA250_RANGE_MASK, - BMA250_POWER_REG, BMA250_LOWPOWER_MASK, 1, - BMA250_INT_ENABLE_REG, BMA250_DATA_INTEN_MASK, - BMA250_RESET_REG, - bma250_chip_config, - bma250_chip_disable, + .chip_id = BMA250_ID_REG_VAL, + .channels = bma250_channels, + .num_channels = ARRAY_SIZE(bma250_channels), + .scale_table = bma25x_scale_table, + .num_scales = ARRAY_SIZE(bma25x_scale_table), + .bw_table = bma25x_bw_table, + .num_bw = ARRAY_SIZE(bma25x_bw_table), + .center_temp = 48, /* 0 LSB @ 24 degree C */ + .int_reset_reg = BMA250_INT_RESET_REG, + .int_reset_mask = BMA250_INT_RESET_MASK, + .sleep_reg = BMA250_POWER_REG, + .sleep_mask = BMA250_SUSPEND_MASK, + .bw_reg = BMA250_BW_REG, + .bw_mask = BMA250_BW_MASK, + .scale_reg = BMA250_RANGE_REG, + .scale_mask = BMA250_RANGE_MASK, + .power_reg = BMA250_POWER_REG, + .power_mask = BMA250_LOWPOWER_MASK, + .lowpower_val = 1, + .int_enable_reg = BMA250_INT_ENABLE_REG, + .int_enable_mask = BMA250_DATA_INTEN_MASK, + .int_map_reg = BMA250_INT_MAP_REG, + .int_enable_dataready_int1_mask = BMA250_INT1_DATA_MASK, + .softreset_reg = BMA250_RESET_REG, + .chip_config = bma25x_chip_config, + .chip_disable = bma25x_chip_disable, + }, + [BMA254] = { + .chip_id = BMA254_ID_REG_VAL, + .channels = bma254_channels, + .num_channels = ARRAY_SIZE(bma254_channels), + .scale_table = bma25x_scale_table, + .num_scales = ARRAY_SIZE(bma25x_scale_table), + .bw_table = bma25x_bw_table, + .num_bw = ARRAY_SIZE(bma25x_bw_table), + .center_temp = 46, /* 0 LSB @ 23 degree C */ + .int_reset_reg = BMA254_INT_RESET_REG, + .int_reset_mask = BMA254_INT_RESET_MASK, + .sleep_reg = BMA254_POWER_REG, + .sleep_mask = BMA254_SUSPEND_MASK, + .bw_reg = BMA254_BW_REG, + .bw_mask = BMA254_BW_MASK, + .scale_reg = BMA254_RANGE_REG, + .scale_mask = BMA254_RANGE_MASK, + .power_reg = BMA254_POWER_REG, + .power_mask = BMA254_LOWPOWER_MASK, + .lowpower_val = 1, + .int_enable_reg = BMA254_INT_ENABLE_REG, + .int_enable_mask = BMA254_DATA_INTEN_MASK, + .int_map_reg = BMA254_INT_MAP_REG, + .int_enable_dataready_int1_mask = BMA254_INT1_DATA_MASK, + .softreset_reg = BMA254_RESET_REG, + .chip_config = bma25x_chip_config, + .chip_disable = bma25x_chip_disable, }, }; @@ -712,12 +808,13 @@ static const struct iio_trigger_ops bma180_trigger_ops = { static int bma180_probe(struct i2c_client *client, const struct i2c_device_id *id) { + struct device *dev = &client->dev; struct bma180_data *data; struct iio_dev *indio_dev; enum chip_ids chip; int ret; - indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data)); + indio_dev = devm_iio_device_alloc(dev, sizeof(*data)); if (!indio_dev) return -ENOMEM; @@ -725,22 +822,56 @@ static int bma180_probe(struct i2c_client *client, i2c_set_clientdata(client, indio_dev); data->client = client; if (client->dev.of_node) - chip = (enum chip_ids)of_device_get_match_data(&client->dev); + chip = (enum chip_ids)of_device_get_match_data(dev); else chip = id->driver_data; data->part_info = &bma180_part_info[chip]; - ret = iio_read_mount_matrix(&client->dev, "mount-matrix", + ret = iio_read_mount_matrix(dev, "mount-matrix", &data->orientation); if (ret) return ret; + data->vdd_supply = devm_regulator_get(dev, "vdd"); + if (IS_ERR(data->vdd_supply)) { + if (PTR_ERR(data->vdd_supply) != -EPROBE_DEFER) + dev_err(dev, "Failed to get vdd regulator %d\n", + (int)PTR_ERR(data->vdd_supply)); + return PTR_ERR(data->vdd_supply); + } + data->vddio_supply = devm_regulator_get(dev, "vddio"); + if (IS_ERR(data->vddio_supply)) { + if (PTR_ERR(data->vddio_supply) != -EPROBE_DEFER) + dev_err(dev, "Failed to get vddio regulator %d\n", + (int)PTR_ERR(data->vddio_supply)); + return PTR_ERR(data->vddio_supply); + } + /* Typical voltage 2.4V these are min and max */ + ret = regulator_set_voltage(data->vdd_supply, 1620000, 3600000); + if (ret) + return ret; + ret = regulator_set_voltage(data->vddio_supply, 1200000, 3600000); + if (ret) + return ret; + ret = regulator_enable(data->vdd_supply); + if (ret) { + dev_err(dev, "Failed to enable vdd regulator: %d\n", ret); + return ret; + } + ret = regulator_enable(data->vddio_supply); + if (ret) { + dev_err(dev, "Failed to enable vddio regulator: %d\n", ret); + goto err_disable_vdd; + } + /* Wait to make sure we started up properly (3 ms at least) */ + usleep_range(3000, 5000); + ret = data->part_info->chip_config(data); if (ret < 0) goto err_chip_disable; mutex_init(&data->mutex); - indio_dev->dev.parent = &client->dev; + indio_dev->dev.parent = dev; indio_dev->channels = data->part_info->channels; indio_dev->num_channels = data->part_info->num_channels; indio_dev->name = id->name; @@ -755,15 +886,15 @@ static int bma180_probe(struct i2c_client *client, goto err_chip_disable; } - ret = devm_request_irq(&client->dev, client->irq, + ret = devm_request_irq(dev, client->irq, iio_trigger_generic_data_rdy_poll, IRQF_TRIGGER_RISING, "bma180_event", data->trig); if (ret) { - dev_err(&client->dev, "unable to request IRQ\n"); + dev_err(dev, "unable to request IRQ\n"); goto err_trigger_free; } - data->trig->dev.parent = &client->dev; + data->trig->dev.parent = dev; data->trig->ops = &bma180_trigger_ops; iio_trigger_set_drvdata(data->trig, indio_dev); indio_dev->trig = iio_trigger_get(data->trig); @@ -776,13 +907,13 @@ static int bma180_probe(struct i2c_client *client, ret = iio_triggered_buffer_setup(indio_dev, NULL, bma180_trigger_handler, NULL); if (ret < 0) { - dev_err(&client->dev, "unable to setup iio triggered buffer\n"); + dev_err(dev, "unable to setup iio triggered buffer\n"); goto err_trigger_unregister; } ret = iio_device_register(indio_dev); if (ret < 0) { - dev_err(&client->dev, "unable to register iio device\n"); + dev_err(dev, "unable to register iio device\n"); goto err_buffer_cleanup; } @@ -797,6 +928,9 @@ err_trigger_free: iio_trigger_free(data->trig); err_chip_disable: data->part_info->chip_disable(data); + regulator_disable(data->vddio_supply); +err_disable_vdd: + regulator_disable(data->vdd_supply); return ret; } @@ -816,6 +950,8 @@ static int bma180_remove(struct i2c_client *client) mutex_lock(&data->mutex); data->part_info->chip_disable(data); mutex_unlock(&data->mutex); + regulator_disable(data->vddio_supply); + regulator_disable(data->vdd_supply); return 0; } @@ -856,6 +992,7 @@ static SIMPLE_DEV_PM_OPS(bma180_pm_ops, bma180_suspend, bma180_resume); static const struct i2c_device_id bma180_ids[] = { { "bma180", BMA180 }, { "bma250", BMA250 }, + { "bma254", BMA254 }, { } }; @@ -870,6 +1007,10 @@ static const struct of_device_id bma180_of_match[] = { .compatible = "bosch,bma250", .data = (void *)BMA250 }, + { + .compatible = "bosch,bma254", + .data = (void *)BMA254 + }, { } }; MODULE_DEVICE_TABLE(of, bma180_of_match); @@ -889,5 +1030,5 @@ module_i2c_driver(bma180_driver); MODULE_AUTHOR("Kravchenko Oleksandr <x0199363@ti.com>"); MODULE_AUTHOR("Texas Instruments, Inc."); -MODULE_DESCRIPTION("Bosch BMA180/BMA250 triaxial acceleration sensor"); +MODULE_DESCRIPTION("Bosch BMA180/BMA25x triaxial acceleration sensor"); MODULE_LICENSE("GPL"); diff --git a/drivers/iio/accel/bma400.h b/drivers/iio/accel/bma400.h new file mode 100644 index 000000000000..5ad10db9819f --- /dev/null +++ b/drivers/iio/accel/bma400.h @@ -0,0 +1,99 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * Register constants and other forward declarations needed by the bma400 + * sources. + * + * Copyright 2019 Dan Robertson <dan@dlrobertson.com> + */ + +#ifndef _BMA400_H_ +#define _BMA400_H_ + +#include <linux/bits.h> +#include <linux/regmap.h> + +/* + * Read-Only Registers + */ + +/* Status and ID registers */ +#define BMA400_CHIP_ID_REG 0x00 +#define BMA400_ERR_REG 0x02 +#define BMA400_STATUS_REG 0x03 + +/* Acceleration registers */ +#define BMA400_X_AXIS_LSB_REG 0x04 +#define BMA400_X_AXIS_MSB_REG 0x05 +#define BMA400_Y_AXIS_LSB_REG 0x06 +#define BMA400_Y_AXIS_MSB_REG 0x07 +#define BMA400_Z_AXIS_LSB_REG 0x08 +#define BMA400_Z_AXIS_MSB_REG 0x09 + +/* Sensor time registers */ +#define BMA400_SENSOR_TIME0 0x0a +#define BMA400_SENSOR_TIME1 0x0b +#define BMA400_SENSOR_TIME2 0x0c + +/* Event and interrupt registers */ +#define BMA400_EVENT_REG 0x0d +#define BMA400_INT_STAT0_REG 0x0e +#define BMA400_INT_STAT1_REG 0x0f +#define BMA400_INT_STAT2_REG 0x10 + +/* Temperature register */ +#define BMA400_TEMP_DATA_REG 0x11 + +/* FIFO length and data registers */ +#define BMA400_FIFO_LENGTH0_REG 0x12 +#define BMA400_FIFO_LENGTH1_REG 0x13 +#define BMA400_FIFO_DATA_REG 0x14 + +/* Step count registers */ +#define BMA400_STEP_CNT0_REG 0x15 +#define BMA400_STEP_CNT1_REG 0x16 +#define BMA400_STEP_CNT3_REG 0x17 +#define BMA400_STEP_STAT_REG 0x18 + +/* + * Read-write configuration registers + */ +#define BMA400_ACC_CONFIG0_REG 0x19 +#define BMA400_ACC_CONFIG1_REG 0x1a +#define BMA400_ACC_CONFIG2_REG 0x1b +#define BMA400_CMD_REG 0x7e + +/* Chip ID of BMA 400 devices found in the chip ID register. */ +#define BMA400_ID_REG_VAL 0x90 + +#define BMA400_LP_OSR_SHIFT 5 +#define BMA400_NP_OSR_SHIFT 4 +#define BMA400_SCALE_SHIFT 6 + +#define BMA400_TWO_BITS_MASK GENMASK(1, 0) +#define BMA400_LP_OSR_MASK GENMASK(6, 5) +#define BMA400_NP_OSR_MASK GENMASK(5, 4) +#define BMA400_ACC_ODR_MASK GENMASK(3, 0) +#define BMA400_ACC_SCALE_MASK GENMASK(7, 6) + +#define BMA400_ACC_ODR_MIN_RAW 0x05 +#define BMA400_ACC_ODR_LP_RAW 0x06 +#define BMA400_ACC_ODR_MAX_RAW 0x0b + +#define BMA400_ACC_ODR_MAX_HZ 800 +#define BMA400_ACC_ODR_MIN_WHOLE_HZ 25 +#define BMA400_ACC_ODR_MIN_HZ 12 + +#define BMA400_SCALE_MIN 38357 +#define BMA400_SCALE_MAX 306864 + +#define BMA400_NUM_REGULATORS 2 +#define BMA400_VDD_REGULATOR 0 +#define BMA400_VDDIO_REGULATOR 1 + +extern const struct regmap_config bma400_regmap_config; + +int bma400_probe(struct device *dev, struct regmap *regmap, const char *name); + +int bma400_remove(struct device *dev); + +#endif diff --git a/drivers/iio/accel/bma400_core.c b/drivers/iio/accel/bma400_core.c new file mode 100644 index 000000000000..cc77f89c048b --- /dev/null +++ b/drivers/iio/accel/bma400_core.c @@ -0,0 +1,853 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Core IIO driver for Bosch BMA400 triaxial acceleration sensor. + * + * Copyright 2019 Dan Robertson <dan@dlrobertson.com> + * + * TODO: + * - Support for power management + * - Support events and interrupts + * - Create channel for step count + * - Create channel for sensor time + */ + +#include <linux/bitops.h> +#include <linux/device.h> +#include <linux/iio/iio.h> +#include <linux/iio/sysfs.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/mutex.h> +#include <linux/regmap.h> +#include <linux/regulator/consumer.h> + +#include "bma400.h" + +/* + * The G-range selection may be one of 2g, 4g, 8, or 16g. The scale may + * be selected with the acc_range bits of the ACC_CONFIG1 register. + * NB: This buffer is populated in the device init. + */ +static int bma400_scales[8]; + +/* + * See the ACC_CONFIG1 section of the datasheet. + * NB: This buffer is populated in the device init. + */ +static int bma400_sample_freqs[14]; + +static const int bma400_osr_range[] = { 0, 1, 3 }; + +/* See the ACC_CONFIG0 section of the datasheet */ +enum bma400_power_mode { + POWER_MODE_SLEEP = 0x00, + POWER_MODE_LOW = 0x01, + POWER_MODE_NORMAL = 0x02, + POWER_MODE_INVALID = 0x03, +}; + +struct bma400_sample_freq { + int hz; + int uhz; +}; + +struct bma400_data { + struct device *dev; + struct regmap *regmap; + struct regulator_bulk_data regulators[BMA400_NUM_REGULATORS]; + struct mutex mutex; /* data register lock */ + struct iio_mount_matrix orientation; + enum bma400_power_mode power_mode; + struct bma400_sample_freq sample_freq; + int oversampling_ratio; + int scale; +}; + +static bool bma400_is_writable_reg(struct device *dev, unsigned int reg) +{ + switch (reg) { + case BMA400_CHIP_ID_REG: + case BMA400_ERR_REG: + case BMA400_STATUS_REG: + case BMA400_X_AXIS_LSB_REG: + case BMA400_X_AXIS_MSB_REG: + case BMA400_Y_AXIS_LSB_REG: + case BMA400_Y_AXIS_MSB_REG: + case BMA400_Z_AXIS_LSB_REG: + case BMA400_Z_AXIS_MSB_REG: + case BMA400_SENSOR_TIME0: + case BMA400_SENSOR_TIME1: + case BMA400_SENSOR_TIME2: + case BMA400_EVENT_REG: + case BMA400_INT_STAT0_REG: + case BMA400_INT_STAT1_REG: + case BMA400_INT_STAT2_REG: + case BMA400_TEMP_DATA_REG: + case BMA400_FIFO_LENGTH0_REG: + case BMA400_FIFO_LENGTH1_REG: + case BMA400_FIFO_DATA_REG: + case BMA400_STEP_CNT0_REG: + case BMA400_STEP_CNT1_REG: + case BMA400_STEP_CNT3_REG: + case BMA400_STEP_STAT_REG: + return false; + default: + return true; + } +} + +static bool bma400_is_volatile_reg(struct device *dev, unsigned int reg) +{ + switch (reg) { + case BMA400_ERR_REG: + case BMA400_STATUS_REG: + case BMA400_X_AXIS_LSB_REG: + case BMA400_X_AXIS_MSB_REG: + case BMA400_Y_AXIS_LSB_REG: + case BMA400_Y_AXIS_MSB_REG: + case BMA400_Z_AXIS_LSB_REG: + case BMA400_Z_AXIS_MSB_REG: + case BMA400_SENSOR_TIME0: + case BMA400_SENSOR_TIME1: + case BMA400_SENSOR_TIME2: + case BMA400_EVENT_REG: + case BMA400_INT_STAT0_REG: + case BMA400_INT_STAT1_REG: + case BMA400_INT_STAT2_REG: + case BMA400_TEMP_DATA_REG: + case BMA400_FIFO_LENGTH0_REG: + case BMA400_FIFO_LENGTH1_REG: + case BMA400_FIFO_DATA_REG: + case BMA400_STEP_CNT0_REG: + case BMA400_STEP_CNT1_REG: + case BMA400_STEP_CNT3_REG: + case BMA400_STEP_STAT_REG: + return true; + default: + return false; + } +} + +const struct regmap_config bma400_regmap_config = { + .reg_bits = 8, + .val_bits = 8, + .max_register = BMA400_CMD_REG, + .cache_type = REGCACHE_RBTREE, + .writeable_reg = bma400_is_writable_reg, + .volatile_reg = bma400_is_volatile_reg, +}; +EXPORT_SYMBOL(bma400_regmap_config); + +static const struct iio_mount_matrix * +bma400_accel_get_mount_matrix(const struct iio_dev *indio_dev, + const struct iio_chan_spec *chan) +{ + struct bma400_data *data = iio_priv(indio_dev); + + return &data->orientation; +} + +static const struct iio_chan_spec_ext_info bma400_ext_info[] = { + IIO_MOUNT_MATRIX(IIO_SHARED_BY_DIR, bma400_accel_get_mount_matrix), + { } +}; + +#define BMA400_ACC_CHANNEL(_axis) { \ + .type = IIO_ACCEL, \ + .modified = 1, \ + .channel2 = IIO_MOD_##_axis, \ + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SAMP_FREQ) | \ + BIT(IIO_CHAN_INFO_SCALE) | \ + BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO), \ + .info_mask_shared_by_type_available = BIT(IIO_CHAN_INFO_SAMP_FREQ) | \ + BIT(IIO_CHAN_INFO_SCALE) | \ + BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO), \ + .ext_info = bma400_ext_info, \ +} + +static const struct iio_chan_spec bma400_channels[] = { + BMA400_ACC_CHANNEL(X), + BMA400_ACC_CHANNEL(Y), + BMA400_ACC_CHANNEL(Z), + { + .type = IIO_TEMP, + .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED), + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SAMP_FREQ), + }, +}; + +static int bma400_get_temp_reg(struct bma400_data *data, int *val, int *val2) +{ + unsigned int raw_temp; + int host_temp; + int ret; + + if (data->power_mode == POWER_MODE_SLEEP) + return -EBUSY; + + ret = regmap_read(data->regmap, BMA400_TEMP_DATA_REG, &raw_temp); + if (ret) + return ret; + + host_temp = sign_extend32(raw_temp, 7); + /* + * The formula for the TEMP_DATA register in the datasheet + * is: x * 0.5 + 23 + */ + *val = (host_temp >> 1) + 23; + *val2 = (host_temp & 0x1) * 500000; + return IIO_VAL_INT_PLUS_MICRO; +} + +static int bma400_get_accel_reg(struct bma400_data *data, + const struct iio_chan_spec *chan, + int *val) +{ + __le16 raw_accel; + int lsb_reg; + int ret; + + if (data->power_mode == POWER_MODE_SLEEP) + return -EBUSY; + + switch (chan->channel2) { + case IIO_MOD_X: + lsb_reg = BMA400_X_AXIS_LSB_REG; + break; + case IIO_MOD_Y: + lsb_reg = BMA400_Y_AXIS_LSB_REG; + break; + case IIO_MOD_Z: + lsb_reg = BMA400_Z_AXIS_LSB_REG; + break; + default: + dev_err(data->dev, "invalid axis channel modifier\n"); + return -EINVAL; + } + + /* bulk read two registers, with the base being the LSB register */ + ret = regmap_bulk_read(data->regmap, lsb_reg, &raw_accel, + sizeof(raw_accel)); + if (ret) + return ret; + + *val = sign_extend32(le16_to_cpu(raw_accel), 11); + return IIO_VAL_INT; +} + +static void bma400_output_data_rate_from_raw(int raw, unsigned int *val, + unsigned int *val2) +{ + *val = BMA400_ACC_ODR_MAX_HZ >> (BMA400_ACC_ODR_MAX_RAW - raw); + if (raw > BMA400_ACC_ODR_MIN_RAW) + *val2 = 0; + else + *val2 = 500000; +} + +static int bma400_get_accel_output_data_rate(struct bma400_data *data) +{ + unsigned int val; + unsigned int odr; + int ret; + + switch (data->power_mode) { + case POWER_MODE_LOW: + /* + * Runs at a fixed rate in low-power mode. See section 4.3 + * in the datasheet. + */ + bma400_output_data_rate_from_raw(BMA400_ACC_ODR_LP_RAW, + &data->sample_freq.hz, + &data->sample_freq.uhz); + return 0; + case POWER_MODE_NORMAL: + /* + * In normal mode the ODR can be found in the ACC_CONFIG1 + * register. + */ + ret = regmap_read(data->regmap, BMA400_ACC_CONFIG1_REG, &val); + if (ret) + goto error; + + odr = val & BMA400_ACC_ODR_MASK; + if (odr < BMA400_ACC_ODR_MIN_RAW || + odr > BMA400_ACC_ODR_MAX_RAW) { + ret = -EINVAL; + goto error; + } + + bma400_output_data_rate_from_raw(odr, &data->sample_freq.hz, + &data->sample_freq.uhz); + return 0; + case POWER_MODE_SLEEP: + data->sample_freq.hz = 0; + data->sample_freq.uhz = 0; + return 0; + default: + ret = 0; + goto error; + } +error: + data->sample_freq.hz = -1; + data->sample_freq.uhz = -1; + return ret; +} + +static int bma400_set_accel_output_data_rate(struct bma400_data *data, + int hz, int uhz) +{ + unsigned int idx; + unsigned int odr; + unsigned int val; + int ret; + + if (hz >= BMA400_ACC_ODR_MIN_WHOLE_HZ) { + if (uhz || hz > BMA400_ACC_ODR_MAX_HZ) + return -EINVAL; + + /* Note this works because MIN_WHOLE_HZ is odd */ + idx = __ffs(hz); + + if (hz >> idx != BMA400_ACC_ODR_MIN_WHOLE_HZ) + return -EINVAL; + + idx += BMA400_ACC_ODR_MIN_RAW + 1; + } else if (hz == BMA400_ACC_ODR_MIN_HZ && uhz == 500000) { + idx = BMA400_ACC_ODR_MIN_RAW; + } else { + return -EINVAL; + } + + ret = regmap_read(data->regmap, BMA400_ACC_CONFIG1_REG, &val); + if (ret) + return ret; + + /* preserve the range and normal mode osr */ + odr = (~BMA400_ACC_ODR_MASK & val) | idx; + + ret = regmap_write(data->regmap, BMA400_ACC_CONFIG1_REG, odr); + if (ret) + return ret; + + bma400_output_data_rate_from_raw(idx, &data->sample_freq.hz, + &data->sample_freq.uhz); + return 0; +} + +static int bma400_get_accel_oversampling_ratio(struct bma400_data *data) +{ + unsigned int val; + unsigned int osr; + int ret; + + /* + * The oversampling ratio is stored in a different register + * based on the power-mode. In normal mode the OSR is stored + * in ACC_CONFIG1. In low-power mode it is stored in + * ACC_CONFIG0. + */ + switch (data->power_mode) { + case POWER_MODE_LOW: + ret = regmap_read(data->regmap, BMA400_ACC_CONFIG0_REG, &val); + if (ret) { + data->oversampling_ratio = -1; + return ret; + } + + osr = (val & BMA400_LP_OSR_MASK) >> BMA400_LP_OSR_SHIFT; + + data->oversampling_ratio = osr; + return 0; + case POWER_MODE_NORMAL: + ret = regmap_read(data->regmap, BMA400_ACC_CONFIG1_REG, &val); + if (ret) { + data->oversampling_ratio = -1; + return ret; + } + + osr = (val & BMA400_NP_OSR_MASK) >> BMA400_NP_OSR_SHIFT; + + data->oversampling_ratio = osr; + return 0; + case POWER_MODE_SLEEP: + data->oversampling_ratio = 0; + return 0; + default: + data->oversampling_ratio = -1; + return -EINVAL; + } +} + +static int bma400_set_accel_oversampling_ratio(struct bma400_data *data, + int val) +{ + unsigned int acc_config; + int ret; + + if (val & ~BMA400_TWO_BITS_MASK) + return -EINVAL; + + /* + * The oversampling ratio is stored in a different register + * based on the power-mode. + */ + switch (data->power_mode) { + case POWER_MODE_LOW: + ret = regmap_read(data->regmap, BMA400_ACC_CONFIG0_REG, + &acc_config); + if (ret) + return ret; + + ret = regmap_write(data->regmap, BMA400_ACC_CONFIG0_REG, + (acc_config & ~BMA400_LP_OSR_MASK) | + (val << BMA400_LP_OSR_SHIFT)); + if (ret) { + dev_err(data->dev, "Failed to write out OSR\n"); + return ret; + } + + data->oversampling_ratio = val; + return 0; + case POWER_MODE_NORMAL: + ret = regmap_read(data->regmap, BMA400_ACC_CONFIG1_REG, + &acc_config); + if (ret) + return ret; + + ret = regmap_write(data->regmap, BMA400_ACC_CONFIG1_REG, + (acc_config & ~BMA400_NP_OSR_MASK) | + (val << BMA400_NP_OSR_SHIFT)); + if (ret) { + dev_err(data->dev, "Failed to write out OSR\n"); + return ret; + } + + data->oversampling_ratio = val; + return 0; + default: + return -EINVAL; + } + return ret; +} + +static int bma400_accel_scale_to_raw(struct bma400_data *data, + unsigned int val) +{ + int raw; + + if (val == 0) + return -EINVAL; + + /* Note this works because BMA400_SCALE_MIN is odd */ + raw = __ffs(val); + + if (val >> raw != BMA400_SCALE_MIN) + return -EINVAL; + + return raw; +} + +static int bma400_get_accel_scale(struct bma400_data *data) +{ + unsigned int raw_scale; + unsigned int val; + int ret; + + ret = regmap_read(data->regmap, BMA400_ACC_CONFIG1_REG, &val); + if (ret) + return ret; + + raw_scale = (val & BMA400_ACC_SCALE_MASK) >> BMA400_SCALE_SHIFT; + if (raw_scale > BMA400_TWO_BITS_MASK) + return -EINVAL; + + data->scale = BMA400_SCALE_MIN << raw_scale; + + return 0; +} + +static int bma400_set_accel_scale(struct bma400_data *data, unsigned int val) +{ + unsigned int acc_config; + int raw; + int ret; + + ret = regmap_read(data->regmap, BMA400_ACC_CONFIG1_REG, &acc_config); + if (ret) + return ret; + + raw = bma400_accel_scale_to_raw(data, val); + if (raw < 0) + return raw; + + ret = regmap_write(data->regmap, BMA400_ACC_CONFIG1_REG, + (acc_config & ~BMA400_ACC_SCALE_MASK) | + (raw << BMA400_SCALE_SHIFT)); + if (ret) + return ret; + + data->scale = val; + return 0; +} + +static int bma400_get_power_mode(struct bma400_data *data) +{ + unsigned int val; + int ret; + + ret = regmap_read(data->regmap, BMA400_STATUS_REG, &val); + if (ret) { + dev_err(data->dev, "Failed to read status register\n"); + return ret; + } + + data->power_mode = (val >> 1) & BMA400_TWO_BITS_MASK; + return 0; +} + +static int bma400_set_power_mode(struct bma400_data *data, + enum bma400_power_mode mode) +{ + unsigned int val; + int ret; + + ret = regmap_read(data->regmap, BMA400_ACC_CONFIG0_REG, &val); + if (ret) + return ret; + + if (data->power_mode == mode) + return 0; + + if (mode == POWER_MODE_INVALID) + return -EINVAL; + + /* Preserve the low-power oversample ratio etc */ + ret = regmap_write(data->regmap, BMA400_ACC_CONFIG0_REG, + mode | (val & ~BMA400_TWO_BITS_MASK)); + if (ret) { + dev_err(data->dev, "Failed to write to power-mode\n"); + return ret; + } + + data->power_mode = mode; + + /* + * Update our cached osr and odr based on the new + * power-mode. + */ + bma400_get_accel_output_data_rate(data); + bma400_get_accel_oversampling_ratio(data); + return 0; +} + +static void bma400_init_tables(void) +{ + int raw; + int i; + + for (i = 0; i + 1 < ARRAY_SIZE(bma400_sample_freqs); i += 2) { + raw = (i / 2) + 5; + bma400_output_data_rate_from_raw(raw, &bma400_sample_freqs[i], + &bma400_sample_freqs[i + 1]); + } + + for (i = 0; i + 1 < ARRAY_SIZE(bma400_scales); i += 2) { + raw = i / 2; + bma400_scales[i] = 0; + bma400_scales[i + 1] = BMA400_SCALE_MIN << raw; + } +} + +static int bma400_init(struct bma400_data *data) +{ + unsigned int val; + int ret; + + /* Try to read chip_id register. It must return 0x90. */ + ret = regmap_read(data->regmap, BMA400_CHIP_ID_REG, &val); + if (ret) { + dev_err(data->dev, "Failed to read chip id register\n"); + goto out; + } + + if (val != BMA400_ID_REG_VAL) { + dev_err(data->dev, "Chip ID mismatch\n"); + ret = -ENODEV; + goto out; + } + + data->regulators[BMA400_VDD_REGULATOR].supply = "vdd"; + data->regulators[BMA400_VDDIO_REGULATOR].supply = "vddio"; + ret = devm_regulator_bulk_get(data->dev, + ARRAY_SIZE(data->regulators), + data->regulators); + if (ret) { + if (ret != -EPROBE_DEFER) + dev_err(data->dev, + "Failed to get regulators: %d\n", + ret); + + goto out; + } + ret = regulator_bulk_enable(ARRAY_SIZE(data->regulators), + data->regulators); + if (ret) { + dev_err(data->dev, "Failed to enable regulators: %d\n", + ret); + goto out; + } + + ret = bma400_get_power_mode(data); + if (ret) { + dev_err(data->dev, "Failed to get the initial power-mode\n"); + goto err_reg_disable; + } + + if (data->power_mode != POWER_MODE_NORMAL) { + ret = bma400_set_power_mode(data, POWER_MODE_NORMAL); + if (ret) { + dev_err(data->dev, "Failed to wake up the device\n"); + goto err_reg_disable; + } + /* + * TODO: The datasheet waits 1500us here in the example, but + * lists 2/ODR as the wakeup time. + */ + usleep_range(1500, 2000); + } + + bma400_init_tables(); + + ret = bma400_get_accel_output_data_rate(data); + if (ret) + goto err_reg_disable; + + ret = bma400_get_accel_oversampling_ratio(data); + if (ret) + goto err_reg_disable; + + ret = bma400_get_accel_scale(data); + if (ret) + goto err_reg_disable; + + /* + * Once the interrupt engine is supported we might use the + * data_src_reg, but for now ensure this is set to the + * variable ODR filter selectable by the sample frequency + * channel. + */ + return regmap_write(data->regmap, BMA400_ACC_CONFIG2_REG, 0x00); + +err_reg_disable: + regulator_bulk_disable(ARRAY_SIZE(data->regulators), + data->regulators); +out: + return ret; +} + +static int bma400_read_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, int *val, + int *val2, long mask) +{ + struct bma400_data *data = iio_priv(indio_dev); + int ret; + + switch (mask) { + case IIO_CHAN_INFO_PROCESSED: + mutex_lock(&data->mutex); + ret = bma400_get_temp_reg(data, val, val2); + mutex_unlock(&data->mutex); + return ret; + case IIO_CHAN_INFO_RAW: + mutex_lock(&data->mutex); + ret = bma400_get_accel_reg(data, chan, val); + mutex_unlock(&data->mutex); + return ret; + case IIO_CHAN_INFO_SAMP_FREQ: + switch (chan->type) { + case IIO_ACCEL: + if (data->sample_freq.hz < 0) + return -EINVAL; + + *val = data->sample_freq.hz; + *val2 = data->sample_freq.uhz; + return IIO_VAL_INT_PLUS_MICRO; + case IIO_TEMP: + /* + * Runs at a fixed sampling frequency. See Section 4.4 + * of the datasheet. + */ + *val = 6; + *val2 = 250000; + return IIO_VAL_INT_PLUS_MICRO; + default: + return -EINVAL; + } + case IIO_CHAN_INFO_SCALE: + *val = 0; + *val2 = data->scale; + return IIO_VAL_INT_PLUS_MICRO; + case IIO_CHAN_INFO_OVERSAMPLING_RATIO: + /* + * TODO: We could avoid this logic and returning -EINVAL here if + * we set both the low-power and normal mode OSR registers when + * we configure the device. + */ + if (data->oversampling_ratio < 0) + return -EINVAL; + + *val = data->oversampling_ratio; + return IIO_VAL_INT; + default: + return -EINVAL; + } +} + +static int bma400_read_avail(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + const int **vals, int *type, int *length, + long mask) +{ + switch (mask) { + case IIO_CHAN_INFO_SCALE: + *type = IIO_VAL_INT_PLUS_MICRO; + *vals = bma400_scales; + *length = ARRAY_SIZE(bma400_scales); + return IIO_AVAIL_LIST; + case IIO_CHAN_INFO_OVERSAMPLING_RATIO: + *type = IIO_VAL_INT; + *vals = bma400_osr_range; + *length = ARRAY_SIZE(bma400_osr_range); + return IIO_AVAIL_RANGE; + case IIO_CHAN_INFO_SAMP_FREQ: + *type = IIO_VAL_INT_PLUS_MICRO; + *vals = bma400_sample_freqs; + *length = ARRAY_SIZE(bma400_sample_freqs); + return IIO_AVAIL_LIST; + default: + return -EINVAL; + } +} + +static int bma400_write_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, int val, int val2, + long mask) +{ + struct bma400_data *data = iio_priv(indio_dev); + int ret; + + switch (mask) { + case IIO_CHAN_INFO_SAMP_FREQ: + /* + * The sample frequency is readonly for the temperature + * register and a fixed value in low-power mode. + */ + if (chan->type != IIO_ACCEL) + return -EINVAL; + + mutex_lock(&data->mutex); + ret = bma400_set_accel_output_data_rate(data, val, val2); + mutex_unlock(&data->mutex); + return ret; + case IIO_CHAN_INFO_SCALE: + if (val != 0 || + val2 < BMA400_SCALE_MIN || val2 > BMA400_SCALE_MAX) + return -EINVAL; + + mutex_lock(&data->mutex); + ret = bma400_set_accel_scale(data, val2); + mutex_unlock(&data->mutex); + return ret; + case IIO_CHAN_INFO_OVERSAMPLING_RATIO: + mutex_lock(&data->mutex); + ret = bma400_set_accel_oversampling_ratio(data, val); + mutex_unlock(&data->mutex); + return ret; + default: + return -EINVAL; + } +} + +static int bma400_write_raw_get_fmt(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + long mask) +{ + switch (mask) { + case IIO_CHAN_INFO_SAMP_FREQ: + return IIO_VAL_INT_PLUS_MICRO; + case IIO_CHAN_INFO_SCALE: + return IIO_VAL_INT_PLUS_MICRO; + case IIO_CHAN_INFO_OVERSAMPLING_RATIO: + return IIO_VAL_INT; + default: + return -EINVAL; + } +} + +static const struct iio_info bma400_info = { + .read_raw = bma400_read_raw, + .read_avail = bma400_read_avail, + .write_raw = bma400_write_raw, + .write_raw_get_fmt = bma400_write_raw_get_fmt, +}; + +int bma400_probe(struct device *dev, struct regmap *regmap, const char *name) +{ + struct iio_dev *indio_dev; + struct bma400_data *data; + int ret; + + indio_dev = devm_iio_device_alloc(dev, sizeof(*data)); + if (!indio_dev) + return -ENOMEM; + + data = iio_priv(indio_dev); + data->regmap = regmap; + data->dev = dev; + + ret = bma400_init(data); + if (ret) + return ret; + + ret = iio_read_mount_matrix(dev, "mount-matrix", &data->orientation); + if (ret) + return ret; + + mutex_init(&data->mutex); + indio_dev->dev.parent = dev; + indio_dev->name = name; + indio_dev->info = &bma400_info; + indio_dev->channels = bma400_channels; + indio_dev->num_channels = ARRAY_SIZE(bma400_channels); + indio_dev->modes = INDIO_DIRECT_MODE; + + dev_set_drvdata(dev, indio_dev); + + return iio_device_register(indio_dev); +} +EXPORT_SYMBOL(bma400_probe); + +int bma400_remove(struct device *dev) +{ + struct iio_dev *indio_dev = dev_get_drvdata(dev); + struct bma400_data *data = iio_priv(indio_dev); + int ret; + + mutex_lock(&data->mutex); + ret = bma400_set_power_mode(data, POWER_MODE_SLEEP); + mutex_unlock(&data->mutex); + + regulator_bulk_disable(ARRAY_SIZE(data->regulators), + data->regulators); + + iio_device_unregister(indio_dev); + + return ret; +} +EXPORT_SYMBOL(bma400_remove); + +MODULE_AUTHOR("Dan Robertson <dan@dlrobertson.com>"); +MODULE_DESCRIPTION("Bosch BMA400 triaxial acceleration sensor core"); +MODULE_LICENSE("GPL"); diff --git a/drivers/iio/accel/bma400_i2c.c b/drivers/iio/accel/bma400_i2c.c new file mode 100644 index 000000000000..9dcb7cc9996e --- /dev/null +++ b/drivers/iio/accel/bma400_i2c.c @@ -0,0 +1,61 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * I2C IIO driver for Bosch BMA400 triaxial acceleration sensor. + * + * Copyright 2019 Dan Robertson <dan@dlrobertson.com> + * + * I2C address is either 0x14 or 0x15 depending on SDO + */ +#include <linux/i2c.h> +#include <linux/mod_devicetable.h> +#include <linux/module.h> +#include <linux/regmap.h> + +#include "bma400.h" + +static int bma400_i2c_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct regmap *regmap; + + regmap = devm_regmap_init_i2c(client, &bma400_regmap_config); + if (IS_ERR(regmap)) { + dev_err(&client->dev, "failed to create regmap\n"); + return PTR_ERR(regmap); + } + + return bma400_probe(&client->dev, regmap, id->name); +} + +static int bma400_i2c_remove(struct i2c_client *client) +{ + return bma400_remove(&client->dev); +} + +static const struct i2c_device_id bma400_i2c_ids[] = { + { "bma400", 0 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, bma400_i2c_ids); + +static const struct of_device_id bma400_of_i2c_match[] = { + { .compatible = "bosch,bma400" }, + { } +}; +MODULE_DEVICE_TABLE(of, bma400_of_i2c_match); + +static struct i2c_driver bma400_i2c_driver = { + .driver = { + .name = "bma400", + .of_match_table = bma400_of_i2c_match, + }, + .probe = bma400_i2c_probe, + .remove = bma400_i2c_remove, + .id_table = bma400_i2c_ids, +}; + +module_i2c_driver(bma400_i2c_driver); + +MODULE_AUTHOR("Dan Robertson <dan@dlrobertson.com>"); +MODULE_DESCRIPTION("Bosch BMA400 triaxial acceleration sensor (I2C)"); +MODULE_LICENSE("GPL"); diff --git a/drivers/iio/accel/kxcjk-1013.c b/drivers/iio/accel/kxcjk-1013.c index fee535d6e45b..c9924a65c32a 100644 --- a/drivers/iio/accel/kxcjk-1013.c +++ b/drivers/iio/accel/kxcjk-1013.c @@ -130,6 +130,7 @@ struct kxcjk1013_data { struct i2c_client *client; struct iio_trigger *dready_trig; struct iio_trigger *motion_trig; + struct iio_mount_matrix orientation; struct mutex mutex; s16 buffer[8]; u8 odr_bits; @@ -983,6 +984,20 @@ static const struct iio_event_spec kxcjk1013_event = { BIT(IIO_EV_INFO_PERIOD) }; +static const struct iio_mount_matrix * +kxcjk1013_get_mount_matrix(const struct iio_dev *indio_dev, + const struct iio_chan_spec *chan) +{ + struct kxcjk1013_data *data = iio_priv(indio_dev); + + return &data->orientation; +} + +static const struct iio_chan_spec_ext_info kxcjk1013_ext_info[] = { + IIO_MOUNT_MATRIX(IIO_SHARED_BY_TYPE, kxcjk1013_get_mount_matrix), + { } +}; + #define KXCJK1013_CHANNEL(_axis) { \ .type = IIO_ACCEL, \ .modified = 1, \ @@ -999,6 +1014,7 @@ static const struct iio_event_spec kxcjk1013_event = { .endianness = IIO_LE, \ }, \ .event_spec = &kxcjk1013_event, \ + .ext_info = kxcjk1013_ext_info, \ .num_event_specs = 1 \ } @@ -1267,11 +1283,18 @@ static int kxcjk1013_probe(struct i2c_client *client, data->client = client; pdata = dev_get_platdata(&client->dev); - if (pdata) + if (pdata) { data->active_high_intr = pdata->active_high_intr; - else + data->orientation = pdata->orientation; + } else { data->active_high_intr = true; /* default polarity */ + ret = iio_read_mount_matrix(&client->dev, "mount-matrix", + &data->orientation); + if (ret) + return ret; + } + if (id) { data->chipset = (enum kx_chipset)(id->driver_data); name = id->name; diff --git a/drivers/iio/accel/st_accel.h b/drivers/iio/accel/st_accel.h index af09943f38c9..5b13e293cade 100644 --- a/drivers/iio/accel/st_accel.h +++ b/drivers/iio/accel/st_accel.h @@ -64,7 +64,7 @@ enum st_accel_type { * struct st_sensors_platform_data - default accel platform data * @drdy_int_pin: default accel DRDY is available on INT1 pin. */ -static const struct st_sensors_platform_data default_accel_pdata = { +static __maybe_unused const struct st_sensors_platform_data default_accel_pdata = { .drdy_int_pin = 1, }; diff --git a/drivers/iio/accel/st_accel_i2c.c b/drivers/iio/accel/st_accel_i2c.c index 50fa0fc32baa..633955d764cc 100644 --- a/drivers/iio/accel/st_accel_i2c.c +++ b/drivers/iio/accel/st_accel_i2c.c @@ -18,7 +18,6 @@ #include <linux/iio/common/st_sensors_i2c.h> #include "st_accel.h" -#ifdef CONFIG_OF static const struct of_device_id st_accel_of_match[] = { { /* An older compatible */ @@ -108,9 +107,6 @@ static const struct of_device_id st_accel_of_match[] = { {}, }; MODULE_DEVICE_TABLE(of, st_accel_of_match); -#else -#define st_accel_of_match NULL -#endif #ifdef CONFIG_ACPI static const struct acpi_device_id st_accel_acpi_match[] = { @@ -119,8 +115,6 @@ static const struct acpi_device_id st_accel_acpi_match[] = { { }, }; MODULE_DEVICE_TABLE(acpi, st_accel_acpi_match); -#else -#define st_accel_acpi_match NULL #endif static const struct i2c_device_id st_accel_id_table[] = { @@ -195,7 +189,7 @@ static int st_accel_i2c_remove(struct i2c_client *client) static struct i2c_driver st_accel_driver = { .driver = { .name = "st-accel-i2c", - .of_match_table = of_match_ptr(st_accel_of_match), + .of_match_table = st_accel_of_match, .acpi_match_table = ACPI_PTR(st_accel_acpi_match), }, .probe_new = st_accel_i2c_probe, diff --git a/drivers/iio/accel/st_accel_spi.c b/drivers/iio/accel/st_accel_spi.c index 8af7027d5598..568ff1bae0ee 100644 --- a/drivers/iio/accel/st_accel_spi.c +++ b/drivers/iio/accel/st_accel_spi.c @@ -17,7 +17,6 @@ #include <linux/iio/common/st_sensors_spi.h> #include "st_accel.h" -#ifdef CONFIG_OF /* * For new single-chip sensors use <device_name> as compatible string. * For old single-chip devices keep <device_name>-accel to maintain @@ -96,9 +95,6 @@ static const struct of_device_id st_accel_of_match[] = { {} }; MODULE_DEVICE_TABLE(of, st_accel_of_match); -#else -#define st_accel_of_match NULL -#endif static int st_accel_spi_probe(struct spi_device *spi) { @@ -107,8 +103,7 @@ static int st_accel_spi_probe(struct spi_device *spi) struct iio_dev *indio_dev; int err; - st_sensors_of_name_probe(&spi->dev, st_accel_of_match, - spi->modalias, sizeof(spi->modalias)); + st_sensors_dev_name_probe(&spi->dev, spi->modalias, sizeof(spi->modalias)); settings = st_accel_get_settings(spi->modalias); if (!settings) { @@ -166,7 +161,7 @@ MODULE_DEVICE_TABLE(spi, st_accel_id_table); static struct spi_driver st_accel_driver = { .driver = { .name = "st-accel-spi", - .of_match_table = of_match_ptr(st_accel_of_match), + .of_match_table = st_accel_of_match, }, .probe = st_accel_spi_probe, .remove = st_accel_spi_remove, diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig index 5d8540b7b427..82e33082958c 100644 --- a/drivers/iio/adc/Kconfig +++ b/drivers/iio/adc/Kconfig @@ -21,6 +21,13 @@ config AD_SIGMA_DELTA select IIO_BUFFER select IIO_TRIGGERED_BUFFER +config AD7091R5 + tristate "Analog Devices AD7091R5 ADC Driver" + depends on I2C + select REGMAP_I2C + help + Say yes here to build support for Analog Devices AD7091R-5 ADC. + config AD7124 tristate "Analog Devices AD7124 and similar sigma-delta ADCs driver" depends on SPI_MASTER @@ -523,6 +530,16 @@ config LTC2485 To compile this driver as a module, choose M here: the module will be called ltc2485. +config LTC2496 + tristate "Linear Technology LTC2496 ADC driver" + depends on SPI + help + Say yes here to build support for Linear Technology LTC2496 + 16-Bit 8-/16-Channel Delta Sigma ADC. + + To compile this driver as a module, choose M here: the module will be + called ltc2496. + config LTC2497 tristate "Linear Technology LTC2497 ADC driver" depends on I2C diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile index a1f1fbec0f87..919228900df9 100644 --- a/drivers/iio/adc/Makefile +++ b/drivers/iio/adc/Makefile @@ -6,6 +6,7 @@ # When adding new entries keep the list in alphabetical order obj-$(CONFIG_AB8500_GPADC) += ab8500-gpadc.o obj-$(CONFIG_AD_SIGMA_DELTA) += ad_sigma_delta.o +obj-$(CONFIG_AD7091R5) += ad7091r5.o ad7091r-base.o obj-$(CONFIG_AD7124) += ad7124.o obj-$(CONFIG_AD7266) += ad7266.o obj-$(CONFIG_AD7291) += ad7291.o @@ -50,7 +51,8 @@ obj-$(CONFIG_LPC18XX_ADC) += lpc18xx_adc.o obj-$(CONFIG_LPC32XX_ADC) += lpc32xx_adc.o obj-$(CONFIG_LTC2471) += ltc2471.o obj-$(CONFIG_LTC2485) += ltc2485.o -obj-$(CONFIG_LTC2497) += ltc2497.o +obj-$(CONFIG_LTC2496) += ltc2496.o ltc2497-core.o +obj-$(CONFIG_LTC2497) += ltc2497.o ltc2497-core.o obj-$(CONFIG_MAX1027) += max1027.o obj-$(CONFIG_MAX11100) += max11100.o obj-$(CONFIG_MAX1118) += max1118.o diff --git a/drivers/iio/adc/ad7091r-base.c b/drivers/iio/adc/ad7091r-base.c new file mode 100644 index 000000000000..33c40357bd5e --- /dev/null +++ b/drivers/iio/adc/ad7091r-base.c @@ -0,0 +1,298 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * AD7091RX Analog to Digital converter driver + * + * Copyright 2014-2019 Analog Devices Inc. + */ + +#include <linux/bitops.h> +#include <linux/iio/events.h> +#include <linux/iio/iio.h> +#include <linux/interrupt.h> +#include <linux/module.h> +#include <linux/regmap.h> +#include <linux/regulator/consumer.h> + +#include "ad7091r-base.h" + +#define AD7091R_REG_RESULT 0 +#define AD7091R_REG_CHANNEL 1 +#define AD7091R_REG_CONF 2 +#define AD7091R_REG_ALERT 3 +#define AD7091R_REG_CH_LOW_LIMIT(ch) ((ch) * 3 + 4) +#define AD7091R_REG_CH_HIGH_LIMIT(ch) ((ch) * 3 + 5) +#define AD7091R_REG_CH_HYSTERESIS(ch) ((ch) * 3 + 6) + +/* AD7091R_REG_RESULT */ +#define AD7091R_REG_RESULT_CH_ID(x) (((x) >> 13) & 0x3) +#define AD7091R_REG_RESULT_CONV_RESULT(x) ((x) & 0xfff) + +/* AD7091R_REG_CONF */ +#define AD7091R_REG_CONF_AUTO BIT(8) +#define AD7091R_REG_CONF_CMD BIT(10) + +#define AD7091R_REG_CONF_MODE_MASK \ + (AD7091R_REG_CONF_AUTO | AD7091R_REG_CONF_CMD) + +enum ad7091r_mode { + AD7091R_MODE_SAMPLE, + AD7091R_MODE_COMMAND, + AD7091R_MODE_AUTOCYCLE, +}; + +struct ad7091r_state { + struct device *dev; + struct regmap *map; + struct regulator *vref; + const struct ad7091r_chip_info *chip_info; + enum ad7091r_mode mode; + struct mutex lock; /*lock to prevent concurent reads */ +}; + +static int ad7091r_set_mode(struct ad7091r_state *st, enum ad7091r_mode mode) +{ + int ret, conf; + + switch (mode) { + case AD7091R_MODE_SAMPLE: + conf = 0; + break; + case AD7091R_MODE_COMMAND: + conf = AD7091R_REG_CONF_CMD; + break; + case AD7091R_MODE_AUTOCYCLE: + conf = AD7091R_REG_CONF_AUTO; + break; + default: + return -EINVAL; + } + + ret = regmap_update_bits(st->map, AD7091R_REG_CONF, + AD7091R_REG_CONF_MODE_MASK, conf); + if (ret) + return ret; + + st->mode = mode; + + return 0; +} + +static int ad7091r_set_channel(struct ad7091r_state *st, unsigned int channel) +{ + unsigned int dummy; + int ret; + + /* AD7091R_REG_CHANNEL specified which channels to be converted */ + ret = regmap_write(st->map, AD7091R_REG_CHANNEL, + BIT(channel) | (BIT(channel) << 8)); + if (ret) + return ret; + + /* + * There is a latency of one conversion before the channel conversion + * sequence is updated + */ + return regmap_read(st->map, AD7091R_REG_RESULT, &dummy); +} + +static int ad7091r_read_one(struct iio_dev *iio_dev, + unsigned int channel, unsigned int *read_val) +{ + struct ad7091r_state *st = iio_priv(iio_dev); + unsigned int val; + int ret; + + ret = ad7091r_set_channel(st, channel); + if (ret) + return ret; + + ret = regmap_read(st->map, AD7091R_REG_RESULT, &val); + if (ret) + return ret; + + if (AD7091R_REG_RESULT_CH_ID(val) != channel) + return -EIO; + + *read_val = AD7091R_REG_RESULT_CONV_RESULT(val); + + return 0; +} + +static int ad7091r_read_raw(struct iio_dev *iio_dev, + struct iio_chan_spec const *chan, + int *val, int *val2, long m) +{ + struct ad7091r_state *st = iio_priv(iio_dev); + unsigned int read_val; + int ret; + + mutex_lock(&st->lock); + + switch (m) { + case IIO_CHAN_INFO_RAW: + if (st->mode != AD7091R_MODE_COMMAND) { + ret = -EBUSY; + goto unlock; + } + + ret = ad7091r_read_one(iio_dev, chan->channel, &read_val); + if (ret) + goto unlock; + + *val = read_val; + ret = IIO_VAL_INT; + break; + + case IIO_CHAN_INFO_SCALE: + if (st->vref) { + ret = regulator_get_voltage(st->vref); + if (ret < 0) + goto unlock; + + *val = ret / 1000; + } else { + *val = st->chip_info->vref_mV; + } + + *val2 = chan->scan_type.realbits; + ret = IIO_VAL_FRACTIONAL_LOG2; + break; + + default: + ret = -EINVAL; + break; + } + +unlock: + mutex_unlock(&st->lock); + return ret; +} + +static const struct iio_info ad7091r_info = { + .read_raw = ad7091r_read_raw, +}; + +static irqreturn_t ad7091r_event_handler(int irq, void *private) +{ + struct ad7091r_state *st = (struct ad7091r_state *) private; + struct iio_dev *iio_dev = dev_get_drvdata(st->dev); + unsigned int i, read_val; + int ret; + s64 timestamp = iio_get_time_ns(iio_dev); + + ret = regmap_read(st->map, AD7091R_REG_ALERT, &read_val); + if (ret) + return IRQ_HANDLED; + + for (i = 0; i < st->chip_info->num_channels; i++) { + if (read_val & BIT(i * 2)) + iio_push_event(iio_dev, + IIO_UNMOD_EVENT_CODE(IIO_VOLTAGE, i, + IIO_EV_TYPE_THRESH, + IIO_EV_DIR_RISING), timestamp); + if (read_val & BIT(i * 2 + 1)) + iio_push_event(iio_dev, + IIO_UNMOD_EVENT_CODE(IIO_VOLTAGE, i, + IIO_EV_TYPE_THRESH, + IIO_EV_DIR_FALLING), timestamp); + } + + return IRQ_HANDLED; +} + +static void ad7091r_remove(void *data) +{ + struct ad7091r_state *st = data; + + regulator_disable(st->vref); +} + +int ad7091r_probe(struct device *dev, const char *name, + const struct ad7091r_chip_info *chip_info, + struct regmap *map, int irq) +{ + struct iio_dev *iio_dev; + struct ad7091r_state *st; + int ret; + + iio_dev = devm_iio_device_alloc(dev, sizeof(*st)); + if (!iio_dev) + return -ENOMEM; + + st = iio_priv(iio_dev); + st->dev = dev; + st->chip_info = chip_info; + st->map = map; + + iio_dev->dev.parent = dev; + iio_dev->name = name; + iio_dev->info = &ad7091r_info; + iio_dev->modes = INDIO_DIRECT_MODE; + + iio_dev->num_channels = chip_info->num_channels; + iio_dev->channels = chip_info->channels; + + if (irq) { + ret = devm_request_threaded_irq(dev, irq, NULL, + ad7091r_event_handler, + IRQF_TRIGGER_FALLING | IRQF_ONESHOT, name, st); + if (ret) + return ret; + } + + st->vref = devm_regulator_get_optional(dev, "vref"); + if (IS_ERR(st->vref)) { + if (PTR_ERR(st->vref) == -EPROBE_DEFER) + return -EPROBE_DEFER; + st->vref = NULL; + } else { + ret = regulator_enable(st->vref); + if (ret) + return ret; + ret = devm_add_action_or_reset(dev, ad7091r_remove, st); + if (ret) + return ret; + } + + /* Use command mode by default to convert only desired channels*/ + ret = ad7091r_set_mode(st, AD7091R_MODE_COMMAND); + if (ret) + return ret; + + return devm_iio_device_register(dev, iio_dev); +} +EXPORT_SYMBOL_GPL(ad7091r_probe); + +static bool ad7091r_writeable_reg(struct device *dev, unsigned int reg) +{ + switch (reg) { + case AD7091R_REG_RESULT: + case AD7091R_REG_ALERT: + return false; + default: + return true; + } +} + +static bool ad7091r_volatile_reg(struct device *dev, unsigned int reg) +{ + switch (reg) { + case AD7091R_REG_RESULT: + case AD7091R_REG_ALERT: + return true; + default: + return false; + } +} + +const struct regmap_config ad7091r_regmap_config = { + .reg_bits = 8, + .val_bits = 16, + .writeable_reg = ad7091r_writeable_reg, + .volatile_reg = ad7091r_volatile_reg, +}; +EXPORT_SYMBOL_GPL(ad7091r_regmap_config); + +MODULE_AUTHOR("Beniamin Bia <beniamin.bia@analog.com>"); +MODULE_DESCRIPTION("Analog Devices AD7091Rx multi-channel converters"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/iio/adc/ad7091r-base.h b/drivers/iio/adc/ad7091r-base.h new file mode 100644 index 000000000000..509748aef9b1 --- /dev/null +++ b/drivers/iio/adc/ad7091r-base.h @@ -0,0 +1,26 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * AD7091RX Analog to Digital converter driver + * + * Copyright 2014-2019 Analog Devices Inc. + */ + +#ifndef __DRIVERS_IIO_ADC_AD7091R_BASE_H__ +#define __DRIVERS_IIO_ADC_AD7091R_BASE_H__ + +struct device; +struct ad7091r_state; + +struct ad7091r_chip_info { + unsigned int num_channels; + const struct iio_chan_spec *channels; + unsigned int vref_mV; +}; + +extern const struct regmap_config ad7091r_regmap_config; + +int ad7091r_probe(struct device *dev, const char *name, + const struct ad7091r_chip_info *chip_info, + struct regmap *map, int irq); + +#endif /* __DRIVERS_IIO_ADC_AD7091R_BASE_H__ */ diff --git a/drivers/iio/adc/ad7091r5.c b/drivers/iio/adc/ad7091r5.c new file mode 100644 index 000000000000..9665679c3ea6 --- /dev/null +++ b/drivers/iio/adc/ad7091r5.c @@ -0,0 +1,113 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * AD7091R5 Analog to Digital converter driver + * + * Copyright 2014-2019 Analog Devices Inc. + */ + +#include <linux/i2c.h> +#include <linux/iio/iio.h> +#include <linux/module.h> +#include <linux/regmap.h> + +#include "ad7091r-base.h" + +static const struct iio_event_spec ad7091r5_events[] = { + { + .type = IIO_EV_TYPE_THRESH, + .dir = IIO_EV_DIR_RISING, + .mask_separate = BIT(IIO_EV_INFO_VALUE) | + BIT(IIO_EV_INFO_ENABLE), + }, + { + .type = IIO_EV_TYPE_THRESH, + .dir = IIO_EV_DIR_FALLING, + .mask_separate = BIT(IIO_EV_INFO_VALUE) | + BIT(IIO_EV_INFO_ENABLE), + }, + { + .type = IIO_EV_TYPE_THRESH, + .dir = IIO_EV_DIR_EITHER, + .mask_separate = BIT(IIO_EV_INFO_HYSTERESIS), + }, +}; + +#define AD7091R_CHANNEL(idx, bits, ev, num_ev) { \ + .type = IIO_VOLTAGE, \ + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \ + .indexed = 1, \ + .channel = idx, \ + .event_spec = ev, \ + .num_event_specs = num_ev, \ + .scan_type.storagebits = 16, \ + .scan_type.realbits = bits, \ +} +static const struct iio_chan_spec ad7091r5_channels_irq[] = { + AD7091R_CHANNEL(0, 12, ad7091r5_events, ARRAY_SIZE(ad7091r5_events)), + AD7091R_CHANNEL(1, 12, ad7091r5_events, ARRAY_SIZE(ad7091r5_events)), + AD7091R_CHANNEL(2, 12, ad7091r5_events, ARRAY_SIZE(ad7091r5_events)), + AD7091R_CHANNEL(3, 12, ad7091r5_events, ARRAY_SIZE(ad7091r5_events)), +}; + +static const struct iio_chan_spec ad7091r5_channels_noirq[] = { + AD7091R_CHANNEL(0, 12, NULL, 0), + AD7091R_CHANNEL(1, 12, NULL, 0), + AD7091R_CHANNEL(2, 12, NULL, 0), + AD7091R_CHANNEL(3, 12, NULL, 0), +}; + +static const struct ad7091r_chip_info ad7091r5_chip_info_irq = { + .channels = ad7091r5_channels_irq, + .num_channels = ARRAY_SIZE(ad7091r5_channels_irq), + .vref_mV = 2500, +}; + +static const struct ad7091r_chip_info ad7091r5_chip_info_noirq = { + .channels = ad7091r5_channels_noirq, + .num_channels = ARRAY_SIZE(ad7091r5_channels_noirq), + .vref_mV = 2500, +}; + +static int ad7091r5_i2c_probe(struct i2c_client *i2c, + const struct i2c_device_id *id) +{ + const struct ad7091r_chip_info *chip_info; + struct regmap *map = devm_regmap_init_i2c(i2c, &ad7091r_regmap_config); + + if (IS_ERR(map)) + return PTR_ERR(map); + + if (i2c->irq) + chip_info = &ad7091r5_chip_info_irq; + else + chip_info = &ad7091r5_chip_info_noirq; + + return ad7091r_probe(&i2c->dev, id->name, chip_info, map, i2c->irq); +} + +static const struct of_device_id ad7091r5_dt_ids[] = { + { .compatible = "adi,ad7091r5" }, + {}, +}; +MODULE_DEVICE_TABLE(of, ad7091r5_dt_ids); + +static const struct i2c_device_id ad7091r5_i2c_ids[] = { + {"ad7091r5", 0}, + {} +}; +MODULE_DEVICE_TABLE(i2c, ad7091r5_i2c_ids); + +static struct i2c_driver ad7091r5_driver = { + .driver = { + .name = "ad7091r5", + .of_match_table = ad7091r5_dt_ids, + }, + .probe = ad7091r5_i2c_probe, + .id_table = ad7091r5_i2c_ids, +}; +module_i2c_driver(ad7091r5_driver); + +MODULE_AUTHOR("Beniamin Bia <beniamin.bia@analog.com>"); +MODULE_DESCRIPTION("Analog Devices AD7091R5 multi-channel ADC driver"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/iio/adc/ad7124.c b/drivers/iio/adc/ad7124.c index 306bf15023a7..d9915dc71d1e 100644 --- a/drivers/iio/adc/ad7124.c +++ b/drivers/iio/adc/ad7124.c @@ -9,6 +9,7 @@ #include <linux/delay.h> #include <linux/device.h> #include <linux/err.h> +#include <linux/interrupt.h> #include <linux/kernel.h> #include <linux/module.h> #include <linux/regulator/consumer.h> @@ -224,6 +225,7 @@ static const struct ad_sigma_delta_info ad7124_sigma_delta_info = { .addr_shift = 0, .read_mask = BIT(6), .data_reg = AD7124_DATA, + .irq_flags = IRQF_TRIGGER_FALLING, }; static int ad7124_set_channel_odr(struct ad7124_state *st, diff --git a/drivers/iio/adc/ad7266.c b/drivers/iio/adc/ad7266.c index c31b8eabb894..c8524f098883 100644 --- a/drivers/iio/adc/ad7266.c +++ b/drivers/iio/adc/ad7266.c @@ -11,7 +11,7 @@ #include <linux/spi/spi.h> #include <linux/regulator/consumer.h> #include <linux/err.h> -#include <linux/gpio.h> +#include <linux/gpio/consumer.h> #include <linux/module.h> #include <linux/interrupt.h> @@ -34,7 +34,7 @@ struct ad7266_state { enum ad7266_range range; enum ad7266_mode mode; bool fixed_addr; - struct gpio gpios[3]; + struct gpio_desc *gpios[3]; /* * DMA (thus cache coherency maintenance) requires the @@ -117,7 +117,7 @@ static void ad7266_select_input(struct ad7266_state *st, unsigned int nr) } for (i = 0; i < 3; ++i) - gpio_set_value(st->gpios[i].gpio, (bool)(nr & BIT(i))); + gpiod_set_value(st->gpios[i], (bool)(nr & BIT(i))); } static int ad7266_update_scan_mode(struct iio_dev *indio_dev, @@ -376,7 +376,7 @@ static void ad7266_init_channels(struct iio_dev *indio_dev) } static const char * const ad7266_gpio_labels[] = { - "AD0", "AD1", "AD2", + "ad0", "ad1", "ad2", }; static int ad7266_probe(struct spi_device *spi) @@ -419,14 +419,14 @@ static int ad7266_probe(struct spi_device *spi) if (!st->fixed_addr) { for (i = 0; i < ARRAY_SIZE(st->gpios); ++i) { - st->gpios[i].gpio = pdata->addr_gpios[i]; - st->gpios[i].flags = GPIOF_OUT_INIT_LOW; - st->gpios[i].label = ad7266_gpio_labels[i]; + st->gpios[i] = devm_gpiod_get(&spi->dev, + ad7266_gpio_labels[i], + GPIOD_OUT_LOW); + if (IS_ERR(st->gpios[i])) { + ret = PTR_ERR(st->gpios[i]); + goto error_disable_reg; + } } - ret = gpio_request_array(st->gpios, - ARRAY_SIZE(st->gpios)); - if (ret) - goto error_disable_reg; } } else { st->fixed_addr = true; @@ -465,7 +465,7 @@ static int ad7266_probe(struct spi_device *spi) ret = iio_triggered_buffer_setup(indio_dev, &iio_pollfunc_store_time, &ad7266_trigger_handler, &iio_triggered_buffer_setup_ops); if (ret) - goto error_free_gpios; + goto error_disable_reg; ret = iio_device_register(indio_dev); if (ret) @@ -475,9 +475,6 @@ static int ad7266_probe(struct spi_device *spi) error_buffer_cleanup: iio_triggered_buffer_cleanup(indio_dev); -error_free_gpios: - if (!st->fixed_addr) - gpio_free_array(st->gpios, ARRAY_SIZE(st->gpios)); error_disable_reg: if (!IS_ERR(st->reg)) regulator_disable(st->reg); @@ -492,8 +489,6 @@ static int ad7266_remove(struct spi_device *spi) iio_device_unregister(indio_dev); iio_triggered_buffer_cleanup(indio_dev); - if (!st->fixed_addr) - gpio_free_array(st->gpios, ARRAY_SIZE(st->gpios)); if (!IS_ERR(st->reg)) regulator_disable(st->reg); diff --git a/drivers/iio/adc/ad7780.c b/drivers/iio/adc/ad7780.c index 217a5a5c3c6d..291c1a898129 100644 --- a/drivers/iio/adc/ad7780.c +++ b/drivers/iio/adc/ad7780.c @@ -203,6 +203,7 @@ static const struct ad_sigma_delta_info ad7780_sigma_delta_info = { .set_mode = ad7780_set_mode, .postprocess_sample = ad7780_postprocess_sample, .has_registers = false, + .irq_flags = IRQF_TRIGGER_LOW, }; #define AD7780_CHANNEL(bits, wordsize) \ diff --git a/drivers/iio/adc/ad7791.c b/drivers/iio/adc/ad7791.c index 54025ea10239..abb239392631 100644 --- a/drivers/iio/adc/ad7791.c +++ b/drivers/iio/adc/ad7791.c @@ -205,6 +205,7 @@ static const struct ad_sigma_delta_info ad7791_sigma_delta_info = { .has_registers = true, .addr_shift = 4, .read_mask = BIT(3), + .irq_flags = IRQF_TRIGGER_LOW, }; static int ad7791_read_raw(struct iio_dev *indio_dev, diff --git a/drivers/iio/adc/ad7793.c b/drivers/iio/adc/ad7793.c index bbc41ecf0d2f..b747db97f78a 100644 --- a/drivers/iio/adc/ad7793.c +++ b/drivers/iio/adc/ad7793.c @@ -206,6 +206,7 @@ static const struct ad_sigma_delta_info ad7793_sigma_delta_info = { .has_registers = true, .addr_shift = 3, .read_mask = BIT(6), + .irq_flags = IRQF_TRIGGER_LOW, }; static const struct ad_sd_calib_data ad7793_calib_arr[6] = { diff --git a/drivers/iio/adc/ad7887.c b/drivers/iio/adc/ad7887.c index 6223043e432b..c6a3428e950a 100644 --- a/drivers/iio/adc/ad7887.c +++ b/drivers/iio/adc/ad7887.c @@ -43,11 +43,17 @@ enum ad7887_channels { /** * struct ad7887_chip_info - chip specifc information * @int_vref_mv: the internal reference voltage - * @channel: channel specification + * @channels: channels specification + * @num_channels: number of channels + * @dual_channels: channels specification in dual mode + * @num_dual_channels: number of channels in dual mode */ struct ad7887_chip_info { u16 int_vref_mv; - struct iio_chan_spec channel[3]; + const struct iio_chan_spec *channels; + unsigned int num_channels; + const struct iio_chan_spec *dual_channels; + unsigned int num_dual_channels; }; struct ad7887_state { @@ -183,45 +189,43 @@ static int ad7887_read_raw(struct iio_dev *indio_dev, return -EINVAL; } +#define AD7887_CHANNEL(x) { \ + .type = IIO_VOLTAGE, \ + .indexed = 1, \ + .channel = (x), \ + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \ + .address = (x), \ + .scan_index = (x), \ + .scan_type = { \ + .sign = 'u', \ + .realbits = 12, \ + .storagebits = 16, \ + .shift = 0, \ + .endianness = IIO_BE, \ + }, \ +} + +static const struct iio_chan_spec ad7887_channels[] = { + AD7887_CHANNEL(0), + IIO_CHAN_SOFT_TIMESTAMP(1), +}; + +static const struct iio_chan_spec ad7887_dual_channels[] = { + AD7887_CHANNEL(0), + AD7887_CHANNEL(1), + IIO_CHAN_SOFT_TIMESTAMP(2), +}; static const struct ad7887_chip_info ad7887_chip_info_tbl[] = { /* * More devices added in future */ [ID_AD7887] = { - .channel[0] = { - .type = IIO_VOLTAGE, - .indexed = 1, - .channel = 1, - .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), - .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), - .address = 1, - .scan_index = 1, - .scan_type = { - .sign = 'u', - .realbits = 12, - .storagebits = 16, - .shift = 0, - .endianness = IIO_BE, - }, - }, - .channel[1] = { - .type = IIO_VOLTAGE, - .indexed = 1, - .channel = 0, - .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), - .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), - .address = 0, - .scan_index = 0, - .scan_type = { - .sign = 'u', - .realbits = 12, - .storagebits = 16, - .shift = 0, - .endianness = IIO_BE, - }, - }, - .channel[2] = IIO_CHAN_SOFT_TIMESTAMP(2), + .channels = ad7887_channels, + .num_channels = ARRAY_SIZE(ad7887_channels), + .dual_channels = ad7887_dual_channels, + .num_dual_channels = ARRAY_SIZE(ad7887_dual_channels), .int_vref_mv = 2500, }, }; @@ -306,11 +310,11 @@ static int ad7887_probe(struct spi_device *spi) spi_message_init(&st->msg[AD7887_CH1]); spi_message_add_tail(&st->xfer[3], &st->msg[AD7887_CH1]); - indio_dev->channels = st->chip_info->channel; - indio_dev->num_channels = 3; + indio_dev->channels = st->chip_info->dual_channels; + indio_dev->num_channels = st->chip_info->num_dual_channels; } else { - indio_dev->channels = &st->chip_info->channel[1]; - indio_dev->num_channels = 2; + indio_dev->channels = st->chip_info->channels; + indio_dev->num_channels = st->chip_info->num_channels; } ret = iio_triggered_buffer_setup(indio_dev, &iio_pollfunc_store_time, diff --git a/drivers/iio/adc/ad7923.c b/drivers/iio/adc/ad7923.c index 3212eb4c0f25..1d124c87c6ac 100644 --- a/drivers/iio/adc/ad7923.c +++ b/drivers/iio/adc/ad7923.c @@ -1,6 +1,6 @@ // SPDX-License-Identifier: GPL-2.0-only /* - * AD7904/AD7914/AD7923/AD7924 SPI ADC driver + * AD7904/AD7914/AD7923/AD7924/AD7908/AD7918/AD7928 SPI ADC driver * * Copyright 2011 Analog Devices Inc (from AD7923 Driver) * Copyright 2012 CS Systemes d'Information @@ -29,15 +29,10 @@ #define AD7923_PM_MODE_AS (1) /* auto shutdown */ #define AD7923_PM_MODE_FS (2) /* full shutdown */ #define AD7923_PM_MODE_OPS (3) /* normal operation */ -#define AD7923_CHANNEL_0 (0) /* analog input 0 */ -#define AD7923_CHANNEL_1 (1) /* analog input 1 */ -#define AD7923_CHANNEL_2 (2) /* analog input 2 */ -#define AD7923_CHANNEL_3 (3) /* analog input 3 */ #define AD7923_SEQUENCE_OFF (0) /* no sequence fonction */ #define AD7923_SEQUENCE_PROTECT (2) /* no interrupt write cycle */ #define AD7923_SEQUENCE_ON (3) /* continuous sequence */ -#define AD7923_MAX_CHAN 4 #define AD7923_PM_MODE_WRITE(mode) ((mode) << 4) /* write mode */ #define AD7923_CHANNEL_WRITE(channel) ((channel) << 6) /* write channel */ @@ -78,6 +73,9 @@ enum ad7923_id { AD7904, AD7914, AD7924, + AD7908, + AD7918, + AD7928 }; #define AD7923_V_CHAN(index, bits) \ @@ -106,9 +104,25 @@ const struct iio_chan_spec name ## _channels[] = { \ IIO_CHAN_SOFT_TIMESTAMP(4), \ } +#define DECLARE_AD7908_CHANNELS(name, bits) \ +const struct iio_chan_spec name ## _channels[] = { \ + AD7923_V_CHAN(0, bits), \ + AD7923_V_CHAN(1, bits), \ + AD7923_V_CHAN(2, bits), \ + AD7923_V_CHAN(3, bits), \ + AD7923_V_CHAN(4, bits), \ + AD7923_V_CHAN(5, bits), \ + AD7923_V_CHAN(6, bits), \ + AD7923_V_CHAN(7, bits), \ + IIO_CHAN_SOFT_TIMESTAMP(8), \ +} + static DECLARE_AD7923_CHANNELS(ad7904, 8); static DECLARE_AD7923_CHANNELS(ad7914, 10); static DECLARE_AD7923_CHANNELS(ad7924, 12); +static DECLARE_AD7908_CHANNELS(ad7908, 8); +static DECLARE_AD7908_CHANNELS(ad7918, 10); +static DECLARE_AD7908_CHANNELS(ad7928, 12); static const struct ad7923_chip_info ad7923_chip_info[] = { [AD7904] = { @@ -123,6 +137,18 @@ static const struct ad7923_chip_info ad7923_chip_info[] = { .channels = ad7924_channels, .num_channels = ARRAY_SIZE(ad7924_channels), }, + [AD7908] = { + .channels = ad7908_channels, + .num_channels = ARRAY_SIZE(ad7908_channels), + }, + [AD7918] = { + .channels = ad7918_channels, + .num_channels = ARRAY_SIZE(ad7918_channels), + }, + [AD7928] = { + .channels = ad7928_channels, + .num_channels = ARRAY_SIZE(ad7928_channels), + }, }; /** @@ -135,7 +161,11 @@ static int ad7923_update_scan_mode(struct iio_dev *indio_dev, int i, cmd, len; len = 0; - for_each_set_bit(i, active_scan_mask, AD7923_MAX_CHAN) { + /* + * For this driver the last channel is always the software timestamp so + * skip that one. + */ + for_each_set_bit(i, active_scan_mask, indio_dev->num_channels - 1) { cmd = AD7923_WRITE_CR | AD7923_CHANNEL_WRITE(i) | AD7923_SEQUENCE_WRITE(AD7923_SEQUENCE_OFF) | st->settings; @@ -188,7 +218,7 @@ done: return IRQ_HANDLED; } -static int ad7923_scan_direct(struct ad7923_state *st, unsigned ch) +static int ad7923_scan_direct(struct ad7923_state *st, unsigned int ch) { int ret, cmd; @@ -348,13 +378,29 @@ static const struct spi_device_id ad7923_id[] = { {"ad7914", AD7914}, {"ad7923", AD7924}, {"ad7924", AD7924}, + {"ad7908", AD7908}, + {"ad7918", AD7918}, + {"ad7928", AD7928}, {} }; MODULE_DEVICE_TABLE(spi, ad7923_id); +static const struct of_device_id ad7923_of_match[] = { + { .compatible = "adi,ad7904", }, + { .compatible = "adi,ad7914", }, + { .compatible = "adi,ad7923", }, + { .compatible = "adi,ad7924", }, + { .compatible = "adi,ad7908", }, + { .compatible = "adi,ad7918", }, + { .compatible = "adi,ad7928", }, + { }, +}; +MODULE_DEVICE_TABLE(of, ad7923_of_match); + static struct spi_driver ad7923_driver = { .driver = { .name = "ad7923", + .of_match_table = ad7923_of_match, }, .probe = ad7923_probe, .remove = ad7923_remove, @@ -364,5 +410,5 @@ module_spi_driver(ad7923_driver); MODULE_AUTHOR("Michael Hennerich <michael.hennerich@analog.com>"); MODULE_AUTHOR("Patrick Vasseur <patrick.vasseur@c-s.fr>"); -MODULE_DESCRIPTION("Analog Devices AD7904/AD7914/AD7923/AD7924 ADC"); +MODULE_DESCRIPTION("Analog Devices AD7923 and similar ADC"); MODULE_LICENSE("GPL v2"); diff --git a/drivers/iio/adc/ad799x.c b/drivers/iio/adc/ad799x.c index f658012baad8..ef013af1aec0 100644 --- a/drivers/iio/adc/ad799x.c +++ b/drivers/iio/adc/ad799x.c @@ -167,6 +167,21 @@ static int ad799x_read_config(struct ad799x_state *st) } } +static int ad799x_update_config(struct ad799x_state *st, u16 config) +{ + int ret; + + ret = ad799x_write_config(st, config); + if (ret < 0) + return ret; + ret = ad799x_read_config(st); + if (ret < 0) + return ret; + st->config = ret; + + return 0; +} + /** * ad799x_trigger_handler() bh of trigger launched polling to ring buffer * @@ -808,13 +823,9 @@ static int ad799x_probe(struct i2c_client *client, indio_dev->channels = st->chip_config->channel; indio_dev->num_channels = chip_info->num_channels; - ret = ad799x_write_config(st, st->chip_config->default_config); - if (ret < 0) - goto error_disable_vref; - ret = ad799x_read_config(st); - if (ret < 0) + ret = ad799x_update_config(st, st->chip_config->default_config); + if (ret) goto error_disable_vref; - st->config = ret; ret = iio_triggered_buffer_setup(indio_dev, NULL, &ad799x_trigger_handler, NULL); @@ -864,6 +875,48 @@ static int ad799x_remove(struct i2c_client *client) return 0; } +static int __maybe_unused ad799x_suspend(struct device *dev) +{ + struct iio_dev *indio_dev = i2c_get_clientdata(to_i2c_client(dev)); + struct ad799x_state *st = iio_priv(indio_dev); + + regulator_disable(st->vref); + regulator_disable(st->reg); + + return 0; +} + +static int __maybe_unused ad799x_resume(struct device *dev) +{ + struct iio_dev *indio_dev = i2c_get_clientdata(to_i2c_client(dev)); + struct ad799x_state *st = iio_priv(indio_dev); + int ret; + + ret = regulator_enable(st->reg); + if (ret) { + dev_err(dev, "Unable to enable vcc regulator\n"); + return ret; + } + ret = regulator_enable(st->vref); + if (ret) { + regulator_disable(st->reg); + dev_err(dev, "Unable to enable vref regulator\n"); + return ret; + } + + /* resync config */ + ret = ad799x_update_config(st, st->config); + if (ret) { + regulator_disable(st->vref); + regulator_disable(st->reg); + return ret; + } + + return 0; +} + +static SIMPLE_DEV_PM_OPS(ad799x_pm_ops, ad799x_suspend, ad799x_resume); + static const struct i2c_device_id ad799x_id[] = { { "ad7991", ad7991 }, { "ad7995", ad7995 }, @@ -881,6 +934,7 @@ MODULE_DEVICE_TABLE(i2c, ad799x_id); static struct i2c_driver ad799x_driver = { .driver = { .name = "ad799x", + .pm = &ad799x_pm_ops, }, .probe = ad799x_probe, .remove = ad799x_remove, diff --git a/drivers/iio/adc/ad_sigma_delta.c b/drivers/iio/adc/ad_sigma_delta.c index 8ba90486c787..8115b6de1d6c 100644 --- a/drivers/iio/adc/ad_sigma_delta.c +++ b/drivers/iio/adc/ad_sigma_delta.c @@ -500,7 +500,7 @@ static int ad_sd_probe_trigger(struct iio_dev *indio_dev) ret = request_irq(sigma_delta->spi->irq, ad_sd_data_rdy_trig_poll, - IRQF_TRIGGER_LOW, + sigma_delta->info->irq_flags, indio_dev->name, sigma_delta); if (ret) diff --git a/drivers/iio/adc/at91-sama5d2_adc.c b/drivers/iio/adc/at91-sama5d2_adc.c index e1850f3d5cf3..a5c7771227d5 100644 --- a/drivers/iio/adc/at91-sama5d2_adc.c +++ b/drivers/iio/adc/at91-sama5d2_adc.c @@ -1444,10 +1444,10 @@ static void at91_adc_dma_init(struct platform_device *pdev) if (st->dma_st.dma_chan) return; - st->dma_st.dma_chan = dma_request_slave_channel(&pdev->dev, "rx"); - - if (!st->dma_st.dma_chan) { + st->dma_st.dma_chan = dma_request_chan(&pdev->dev, "rx"); + if (IS_ERR(st->dma_st.dma_chan)) { dev_info(&pdev->dev, "can't get DMA channel\n"); + st->dma_st.dma_chan = NULL; goto dma_exit; } diff --git a/drivers/iio/adc/ltc2496.c b/drivers/iio/adc/ltc2496.c new file mode 100644 index 000000000000..88a30156a849 --- /dev/null +++ b/drivers/iio/adc/ltc2496.c @@ -0,0 +1,108 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * ltc2496.c - Driver for Analog Devices/Linear Technology LTC2496 ADC + * + * Based on ltc2497.c which has + * Copyright (C) 2017 Analog Devices Inc. + * + * Licensed under the GPL-2. + * + * Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/2496fc.pdf + */ + +#include <linux/spi/spi.h> +#include <linux/iio/iio.h> +#include <linux/iio/driver.h> +#include <linux/module.h> +#include <linux/of.h> + +#include "ltc2497.h" + +struct ltc2496_driverdata { + /* this must be the first member */ + struct ltc2497core_driverdata common_ddata; + struct spi_device *spi; + + /* + * DMA (thus cache coherency maintenance) requires the + * transfer buffers to live in their own cache lines. + */ + unsigned char rxbuf[3] ____cacheline_aligned; + unsigned char txbuf[3]; +}; + +static int ltc2496_result_and_measure(struct ltc2497core_driverdata *ddata, + u8 address, int *val) +{ + struct ltc2496_driverdata *st = + container_of(ddata, struct ltc2496_driverdata, common_ddata); + struct spi_transfer t = { + .tx_buf = st->txbuf, + .rx_buf = st->rxbuf, + .len = sizeof(st->txbuf), + }; + int ret; + + st->txbuf[0] = LTC2497_ENABLE | address; + + ret = spi_sync_transfer(st->spi, &t, 1); + if (ret < 0) { + dev_err(&st->spi->dev, "spi_sync_transfer failed: %pe\n", + ERR_PTR(ret)); + return ret; + } + + if (val) + *val = ((st->rxbuf[0] & 0x3f) << 12 | + st->rxbuf[1] << 4 | st->rxbuf[2] >> 4) - + (1 << 17); + + return 0; +} + +static int ltc2496_probe(struct spi_device *spi) +{ + struct iio_dev *indio_dev; + struct ltc2496_driverdata *st; + struct device *dev = &spi->dev; + + indio_dev = devm_iio_device_alloc(dev, sizeof(*st)); + if (!indio_dev) + return -ENOMEM; + + st = iio_priv(indio_dev); + spi_set_drvdata(spi, indio_dev); + st->spi = spi; + st->common_ddata.result_and_measure = ltc2496_result_and_measure; + + return ltc2497core_probe(dev, indio_dev); +} + +static int ltc2496_remove(struct spi_device *spi) +{ + struct iio_dev *indio_dev = spi_get_drvdata(spi); + + ltc2497core_remove(indio_dev); + + return 0; +} + +static const struct of_device_id ltc2496_of_match[] = { + { .compatible = "lltc,ltc2496", }, + {}, +}; +MODULE_DEVICE_TABLE(of, ltc2496_of_match); + +static struct spi_driver ltc2496_driver = { + .driver = { + .name = "ltc2496", + .of_match_table = of_match_ptr(ltc2496_of_match), + }, + .probe = ltc2496_probe, + .remove = ltc2496_remove, +}; +module_spi_driver(ltc2496_driver); + +MODULE_AUTHOR("Uwe Kleine-König <u.kleine-könig@pengutronix.de>"); +MODULE_DESCRIPTION("Linear Technology LTC2496 ADC driver"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/iio/adc/ltc2497-core.c b/drivers/iio/adc/ltc2497-core.c new file mode 100644 index 000000000000..f5f7039caacc --- /dev/null +++ b/drivers/iio/adc/ltc2497-core.c @@ -0,0 +1,243 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * ltc2497-core.c - Common code for Analog Devices/Linear Technology + * LTC2496 and LTC2497 ADCs + * + * Copyright (C) 2017 Analog Devices Inc. + */ + +#include <linux/delay.h> +#include <linux/iio/iio.h> +#include <linux/iio/driver.h> +#include <linux/module.h> +#include <linux/regulator/consumer.h> + +#include "ltc2497.h" + +#define LTC2497_SGL BIT(4) +#define LTC2497_DIFF 0 +#define LTC2497_SIGN BIT(3) + +static int ltc2497core_wait_conv(struct ltc2497core_driverdata *ddata) +{ + s64 time_elapsed; + + time_elapsed = ktime_ms_delta(ktime_get(), ddata->time_prev); + + if (time_elapsed < LTC2497_CONVERSION_TIME_MS) { + /* delay if conversion time not passed + * since last read or write + */ + if (msleep_interruptible( + LTC2497_CONVERSION_TIME_MS - time_elapsed)) + return -ERESTARTSYS; + + return 0; + } + + if (time_elapsed - LTC2497_CONVERSION_TIME_MS <= 0) { + /* We're in automatic mode - + * so the last reading is still not outdated + */ + return 0; + } + + return 1; +} + +static int ltc2497core_read(struct ltc2497core_driverdata *ddata, u8 address, int *val) +{ + int ret; + + ret = ltc2497core_wait_conv(ddata); + if (ret < 0) + return ret; + + if (ret || ddata->addr_prev != address) { + ret = ddata->result_and_measure(ddata, address, NULL); + if (ret < 0) + return ret; + ddata->addr_prev = address; + + if (msleep_interruptible(LTC2497_CONVERSION_TIME_MS)) + return -ERESTARTSYS; + } + + ret = ddata->result_and_measure(ddata, address, val); + if (ret < 0) + return ret; + + ddata->time_prev = ktime_get(); + + return ret; +} + +static int ltc2497core_read_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + int *val, int *val2, long mask) +{ + struct ltc2497core_driverdata *ddata = iio_priv(indio_dev); + int ret; + + switch (mask) { + case IIO_CHAN_INFO_RAW: + mutex_lock(&indio_dev->mlock); + ret = ltc2497core_read(ddata, chan->address, val); + mutex_unlock(&indio_dev->mlock); + if (ret < 0) + return ret; + + return IIO_VAL_INT; + + case IIO_CHAN_INFO_SCALE: + ret = regulator_get_voltage(ddata->ref); + if (ret < 0) + return ret; + + *val = ret / 1000; + *val2 = 17; + + return IIO_VAL_FRACTIONAL_LOG2; + + default: + return -EINVAL; + } +} + +#define LTC2497_CHAN(_chan, _addr, _ds_name) { \ + .type = IIO_VOLTAGE, \ + .indexed = 1, \ + .channel = (_chan), \ + .address = (_addr | (_chan / 2) | ((_chan & 1) ? LTC2497_SIGN : 0)), \ + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \ + .datasheet_name = (_ds_name), \ +} + +#define LTC2497_CHAN_DIFF(_chan, _addr) { \ + .type = IIO_VOLTAGE, \ + .indexed = 1, \ + .channel = (_chan) * 2 + ((_addr) & LTC2497_SIGN ? 1 : 0), \ + .channel2 = (_chan) * 2 + ((_addr) & LTC2497_SIGN ? 0 : 1),\ + .address = (_addr | _chan), \ + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \ + .differential = 1, \ +} + +static const struct iio_chan_spec ltc2497core_channel[] = { + LTC2497_CHAN(0, LTC2497_SGL, "CH0"), + LTC2497_CHAN(1, LTC2497_SGL, "CH1"), + LTC2497_CHAN(2, LTC2497_SGL, "CH2"), + LTC2497_CHAN(3, LTC2497_SGL, "CH3"), + LTC2497_CHAN(4, LTC2497_SGL, "CH4"), + LTC2497_CHAN(5, LTC2497_SGL, "CH5"), + LTC2497_CHAN(6, LTC2497_SGL, "CH6"), + LTC2497_CHAN(7, LTC2497_SGL, "CH7"), + LTC2497_CHAN(8, LTC2497_SGL, "CH8"), + LTC2497_CHAN(9, LTC2497_SGL, "CH9"), + LTC2497_CHAN(10, LTC2497_SGL, "CH10"), + LTC2497_CHAN(11, LTC2497_SGL, "CH11"), + LTC2497_CHAN(12, LTC2497_SGL, "CH12"), + LTC2497_CHAN(13, LTC2497_SGL, "CH13"), + LTC2497_CHAN(14, LTC2497_SGL, "CH14"), + LTC2497_CHAN(15, LTC2497_SGL, "CH15"), + LTC2497_CHAN_DIFF(0, LTC2497_DIFF), + LTC2497_CHAN_DIFF(1, LTC2497_DIFF), + LTC2497_CHAN_DIFF(2, LTC2497_DIFF), + LTC2497_CHAN_DIFF(3, LTC2497_DIFF), + LTC2497_CHAN_DIFF(4, LTC2497_DIFF), + LTC2497_CHAN_DIFF(5, LTC2497_DIFF), + LTC2497_CHAN_DIFF(6, LTC2497_DIFF), + LTC2497_CHAN_DIFF(7, LTC2497_DIFF), + LTC2497_CHAN_DIFF(0, LTC2497_DIFF | LTC2497_SIGN), + LTC2497_CHAN_DIFF(1, LTC2497_DIFF | LTC2497_SIGN), + LTC2497_CHAN_DIFF(2, LTC2497_DIFF | LTC2497_SIGN), + LTC2497_CHAN_DIFF(3, LTC2497_DIFF | LTC2497_SIGN), + LTC2497_CHAN_DIFF(4, LTC2497_DIFF | LTC2497_SIGN), + LTC2497_CHAN_DIFF(5, LTC2497_DIFF | LTC2497_SIGN), + LTC2497_CHAN_DIFF(6, LTC2497_DIFF | LTC2497_SIGN), + LTC2497_CHAN_DIFF(7, LTC2497_DIFF | LTC2497_SIGN), +}; + +static const struct iio_info ltc2497core_info = { + .read_raw = ltc2497core_read_raw, +}; + +int ltc2497core_probe(struct device *dev, struct iio_dev *indio_dev) +{ + struct ltc2497core_driverdata *ddata = iio_priv(indio_dev); + int ret; + + indio_dev->dev.parent = dev; + indio_dev->name = dev_name(dev); + indio_dev->info = <c2497core_info; + indio_dev->modes = INDIO_DIRECT_MODE; + indio_dev->channels = ltc2497core_channel; + indio_dev->num_channels = ARRAY_SIZE(ltc2497core_channel); + + ret = ddata->result_and_measure(ddata, LTC2497_CONFIG_DEFAULT, NULL); + if (ret < 0) + return ret; + + ddata->ref = devm_regulator_get(dev, "vref"); + if (IS_ERR(ddata->ref)) { + if (PTR_ERR(ddata->ref) != -EPROBE_DEFER) + dev_err(dev, "Failed to get vref regulator: %pe\n", + ddata->ref); + + return PTR_ERR(ddata->ref); + } + + ret = regulator_enable(ddata->ref); + if (ret < 0) { + dev_err(dev, "Failed to enable vref regulator: %pe\n", + ERR_PTR(ret)); + return ret; + } + + if (dev->platform_data) { + struct iio_map *plat_data; + + plat_data = (struct iio_map *)dev->platform_data; + + ret = iio_map_array_register(indio_dev, plat_data); + if (ret) { + dev_err(&indio_dev->dev, "iio map err: %d\n", ret); + goto err_regulator_disable; + } + } + + ddata->addr_prev = LTC2497_CONFIG_DEFAULT; + ddata->time_prev = ktime_get(); + + ret = iio_device_register(indio_dev); + if (ret < 0) + goto err_array_unregister; + + return 0; + +err_array_unregister: + iio_map_array_unregister(indio_dev); + +err_regulator_disable: + regulator_disable(ddata->ref); + + return ret; +} +EXPORT_SYMBOL_NS(ltc2497core_probe, LTC2497); + +void ltc2497core_remove(struct iio_dev *indio_dev) +{ + struct ltc2497core_driverdata *ddata = iio_priv(indio_dev); + + iio_device_unregister(indio_dev); + + iio_map_array_unregister(indio_dev); + + regulator_disable(ddata->ref); +} +EXPORT_SYMBOL_NS(ltc2497core_remove, LTC2497); + +MODULE_DESCRIPTION("common code for LTC2496/LTC2497 drivers"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/iio/adc/ltc2497.c b/drivers/iio/adc/ltc2497.c index 470406032720..5db63d7c6bc5 100644 --- a/drivers/iio/adc/ltc2497.c +++ b/drivers/iio/adc/ltc2497.c @@ -7,27 +7,18 @@ * Datasheet: http://cds.linear.com/docs/en/datasheet/2497fd.pdf */ -#include <linux/delay.h> #include <linux/i2c.h> #include <linux/iio/iio.h> #include <linux/iio/driver.h> -#include <linux/iio/sysfs.h> #include <linux/module.h> #include <linux/of.h> -#include <linux/regulator/consumer.h> -#define LTC2497_ENABLE 0xA0 -#define LTC2497_SGL BIT(4) -#define LTC2497_DIFF 0 -#define LTC2497_SIGN BIT(3) -#define LTC2497_CONFIG_DEFAULT LTC2497_ENABLE -#define LTC2497_CONVERSION_TIME_MS 150ULL +#include "ltc2497.h" -struct ltc2497_st { +struct ltc2497_driverdata { + /* this must be the first member */ + struct ltc2497core_driverdata common_ddata; struct i2c_client *client; - struct regulator *ref; - ktime_t time_prev; - u8 addr_prev; /* * DMA (thus cache coherency maintenance) requires the * transfer buffers to live in their own cache lines. @@ -35,232 +26,59 @@ struct ltc2497_st { __be32 buf ____cacheline_aligned; }; -static int ltc2497_wait_conv(struct ltc2497_st *st) +static int ltc2497_result_and_measure(struct ltc2497core_driverdata *ddata, + u8 address, int *val) { - s64 time_elapsed; - - time_elapsed = ktime_ms_delta(ktime_get(), st->time_prev); - - if (time_elapsed < LTC2497_CONVERSION_TIME_MS) { - /* delay if conversion time not passed - * since last read or write - */ - if (msleep_interruptible( - LTC2497_CONVERSION_TIME_MS - time_elapsed)) - return -ERESTARTSYS; - - return 0; - } - - if (time_elapsed - LTC2497_CONVERSION_TIME_MS <= 0) { - /* We're in automatic mode - - * so the last reading is stil not outdated - */ - return 0; - } - - return 1; -} - -static int ltc2497_read(struct ltc2497_st *st, u8 address, int *val) -{ - struct i2c_client *client = st->client; - int ret; - - ret = ltc2497_wait_conv(st); - if (ret < 0) - return ret; - - if (ret || st->addr_prev != address) { - ret = i2c_smbus_write_byte(st->client, - LTC2497_ENABLE | address); - if (ret < 0) - return ret; - st->addr_prev = address; - if (msleep_interruptible(LTC2497_CONVERSION_TIME_MS)) - return -ERESTARTSYS; - } - ret = i2c_master_recv(client, (char *)&st->buf, 3); - if (ret < 0) { - dev_err(&client->dev, "i2c_master_recv failed\n"); - return ret; - } - st->time_prev = ktime_get(); - - /* convert and shift the result, - * and finally convert from offset binary to signed integer - */ - *val = (be32_to_cpu(st->buf) >> 14) - (1 << 17); - - return ret; -} - -static int ltc2497_read_raw(struct iio_dev *indio_dev, - struct iio_chan_spec const *chan, - int *val, int *val2, long mask) -{ - struct ltc2497_st *st = iio_priv(indio_dev); + struct ltc2497_driverdata *st = + container_of(ddata, struct ltc2497_driverdata, common_ddata); int ret; - switch (mask) { - case IIO_CHAN_INFO_RAW: - mutex_lock(&indio_dev->mlock); - ret = ltc2497_read(st, chan->address, val); - mutex_unlock(&indio_dev->mlock); - if (ret < 0) - return ret; - - return IIO_VAL_INT; - - case IIO_CHAN_INFO_SCALE: - ret = regulator_get_voltage(st->ref); - if (ret < 0) + if (val) { + ret = i2c_master_recv(st->client, (char *)&st->buf, 3); + if (ret < 0) { + dev_err(&st->client->dev, "i2c_master_recv failed\n"); return ret; + } - *val = ret / 1000; - *val2 = 17; - - return IIO_VAL_FRACTIONAL_LOG2; - - default: - return -EINVAL; + *val = (be32_to_cpu(st->buf) >> 14) - (1 << 17); } -} -#define LTC2497_CHAN(_chan, _addr, _ds_name) { \ - .type = IIO_VOLTAGE, \ - .indexed = 1, \ - .channel = (_chan), \ - .address = (_addr | (_chan / 2) | ((_chan & 1) ? LTC2497_SIGN : 0)), \ - .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ - .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \ - .datasheet_name = (_ds_name), \ -} - -#define LTC2497_CHAN_DIFF(_chan, _addr) { \ - .type = IIO_VOLTAGE, \ - .indexed = 1, \ - .channel = (_chan) * 2 + ((_addr) & LTC2497_SIGN ? 1 : 0), \ - .channel2 = (_chan) * 2 + ((_addr) & LTC2497_SIGN ? 0 : 1),\ - .address = (_addr | _chan), \ - .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ - .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \ - .differential = 1, \ + ret = i2c_smbus_write_byte(st->client, + LTC2497_ENABLE | address); + if (ret) + dev_err(&st->client->dev, "i2c transfer failed: %pe\n", + ERR_PTR(ret)); + return ret; } -static const struct iio_chan_spec ltc2497_channel[] = { - LTC2497_CHAN(0, LTC2497_SGL, "CH0"), - LTC2497_CHAN(1, LTC2497_SGL, "CH1"), - LTC2497_CHAN(2, LTC2497_SGL, "CH2"), - LTC2497_CHAN(3, LTC2497_SGL, "CH3"), - LTC2497_CHAN(4, LTC2497_SGL, "CH4"), - LTC2497_CHAN(5, LTC2497_SGL, "CH5"), - LTC2497_CHAN(6, LTC2497_SGL, "CH6"), - LTC2497_CHAN(7, LTC2497_SGL, "CH7"), - LTC2497_CHAN(8, LTC2497_SGL, "CH8"), - LTC2497_CHAN(9, LTC2497_SGL, "CH9"), - LTC2497_CHAN(10, LTC2497_SGL, "CH10"), - LTC2497_CHAN(11, LTC2497_SGL, "CH11"), - LTC2497_CHAN(12, LTC2497_SGL, "CH12"), - LTC2497_CHAN(13, LTC2497_SGL, "CH13"), - LTC2497_CHAN(14, LTC2497_SGL, "CH14"), - LTC2497_CHAN(15, LTC2497_SGL, "CH15"), - LTC2497_CHAN_DIFF(0, LTC2497_DIFF), - LTC2497_CHAN_DIFF(1, LTC2497_DIFF), - LTC2497_CHAN_DIFF(2, LTC2497_DIFF), - LTC2497_CHAN_DIFF(3, LTC2497_DIFF), - LTC2497_CHAN_DIFF(4, LTC2497_DIFF), - LTC2497_CHAN_DIFF(5, LTC2497_DIFF), - LTC2497_CHAN_DIFF(6, LTC2497_DIFF), - LTC2497_CHAN_DIFF(7, LTC2497_DIFF), - LTC2497_CHAN_DIFF(0, LTC2497_DIFF | LTC2497_SIGN), - LTC2497_CHAN_DIFF(1, LTC2497_DIFF | LTC2497_SIGN), - LTC2497_CHAN_DIFF(2, LTC2497_DIFF | LTC2497_SIGN), - LTC2497_CHAN_DIFF(3, LTC2497_DIFF | LTC2497_SIGN), - LTC2497_CHAN_DIFF(4, LTC2497_DIFF | LTC2497_SIGN), - LTC2497_CHAN_DIFF(5, LTC2497_DIFF | LTC2497_SIGN), - LTC2497_CHAN_DIFF(6, LTC2497_DIFF | LTC2497_SIGN), - LTC2497_CHAN_DIFF(7, LTC2497_DIFF | LTC2497_SIGN), -}; - -static const struct iio_info ltc2497_info = { - .read_raw = ltc2497_read_raw, -}; - static int ltc2497_probe(struct i2c_client *client, const struct i2c_device_id *id) { struct iio_dev *indio_dev; - struct ltc2497_st *st; - struct iio_map *plat_data; - int ret; + struct ltc2497_driverdata *st; + struct device *dev = &client->dev; if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C | I2C_FUNC_SMBUS_WRITE_BYTE)) return -EOPNOTSUPP; - indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*st)); + indio_dev = devm_iio_device_alloc(dev, sizeof(*st)); if (!indio_dev) return -ENOMEM; st = iio_priv(indio_dev); i2c_set_clientdata(client, indio_dev); st->client = client; + st->common_ddata.result_and_measure = ltc2497_result_and_measure; - indio_dev->dev.parent = &client->dev; - indio_dev->name = id->name; - indio_dev->info = <c2497_info; - indio_dev->modes = INDIO_DIRECT_MODE; - indio_dev->channels = ltc2497_channel; - indio_dev->num_channels = ARRAY_SIZE(ltc2497_channel); - - st->ref = devm_regulator_get(&client->dev, "vref"); - if (IS_ERR(st->ref)) - return PTR_ERR(st->ref); - - ret = regulator_enable(st->ref); - if (ret < 0) - return ret; - - if (client->dev.platform_data) { - plat_data = ((struct iio_map *)client->dev.platform_data); - ret = iio_map_array_register(indio_dev, plat_data); - if (ret) { - dev_err(&indio_dev->dev, "iio map err: %d\n", ret); - goto err_regulator_disable; - } - } - - ret = i2c_smbus_write_byte(st->client, LTC2497_CONFIG_DEFAULT); - if (ret < 0) - goto err_array_unregister; - - st->addr_prev = LTC2497_CONFIG_DEFAULT; - st->time_prev = ktime_get(); - - ret = iio_device_register(indio_dev); - if (ret < 0) - goto err_array_unregister; - - return 0; - -err_array_unregister: - iio_map_array_unregister(indio_dev); - -err_regulator_disable: - regulator_disable(st->ref); - - return ret; + return ltc2497core_probe(dev, indio_dev); } static int ltc2497_remove(struct i2c_client *client) { struct iio_dev *indio_dev = i2c_get_clientdata(client); - struct ltc2497_st *st = iio_priv(indio_dev); - iio_map_array_unregister(indio_dev); - iio_device_unregister(indio_dev); - regulator_disable(st->ref); + ltc2497core_remove(indio_dev); return 0; } diff --git a/drivers/iio/adc/ltc2497.h b/drivers/iio/adc/ltc2497.h new file mode 100644 index 000000000000..d0b42dd6b8ad --- /dev/null +++ b/drivers/iio/adc/ltc2497.h @@ -0,0 +1,18 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#define LTC2497_ENABLE 0xA0 +#define LTC2497_CONFIG_DEFAULT LTC2497_ENABLE +#define LTC2497_CONVERSION_TIME_MS 150ULL + +struct ltc2497core_driverdata { + struct regulator *ref; + ktime_t time_prev; + u8 addr_prev; + int (*result_and_measure)(struct ltc2497core_driverdata *ddata, + u8 address, int *val); +}; + +int ltc2497core_probe(struct device *dev, struct iio_dev *indio_dev); +void ltc2497core_remove(struct iio_dev *indio_dev); + +MODULE_IMPORT_NS(LTC2497); diff --git a/drivers/iio/adc/max9611.c b/drivers/iio/adc/max9611.c index e480529b3f04..04d5ff7d2c8e 100644 --- a/drivers/iio/adc/max9611.c +++ b/drivers/iio/adc/max9611.c @@ -115,22 +115,17 @@ enum max9611_conf_ids { * where data shall be read from */ static const unsigned int max9611_mux_conf[][2] = { - /* CONF_SENSE_1x */ - { MAX9611_MUX_SENSE_1x, MAX9611_REG_CSA_DATA }, - /* CONF_SENSE_4x */ - { MAX9611_MUX_SENSE_4x, MAX9611_REG_CSA_DATA }, - /* CONF_SENSE_8x */ - { MAX9611_MUX_SENSE_8x, MAX9611_REG_CSA_DATA }, - /* CONF_IN_VOLT */ - { MAX9611_INPUT_VOLT, MAX9611_REG_RS_DATA }, - /* CONF_TEMP */ - { MAX9611_MUX_TEMP, MAX9611_REG_TEMP_DATA }, + [CONF_SENSE_1x] = { MAX9611_MUX_SENSE_1x, MAX9611_REG_CSA_DATA }, + [CONF_SENSE_4x] = { MAX9611_MUX_SENSE_4x, MAX9611_REG_CSA_DATA }, + [CONF_SENSE_8x] = { MAX9611_MUX_SENSE_8x, MAX9611_REG_CSA_DATA }, + [CONF_IN_VOLT] = { MAX9611_INPUT_VOLT, MAX9611_REG_RS_DATA }, + [CONF_TEMP] = { MAX9611_MUX_TEMP, MAX9611_REG_TEMP_DATA }, }; enum max9611_csa_gain { - CSA_GAIN_1x, - CSA_GAIN_4x, - CSA_GAIN_8x, + CSA_GAIN_1x = CONF_SENSE_1x, + CSA_GAIN_4x = CONF_SENSE_4x, + CSA_GAIN_8x = CONF_SENSE_8x, }; enum max9611_csa_gain_params { @@ -148,18 +143,9 @@ enum max9611_csa_gain_params { * value; use this structure to retrieve the correct LSB and offset values. */ static const unsigned int max9611_gain_conf[][2] = { - { /* [0] CSA_GAIN_1x */ - MAX9611_CSA_1X_LSB_nV, - MAX9611_CSA_1X_OFFS_RAW, - }, - { /* [1] CSA_GAIN_4x */ - MAX9611_CSA_4X_LSB_nV, - MAX9611_CSA_4X_OFFS_RAW, - }, - { /* [2] CSA_GAIN_8x */ - MAX9611_CSA_8X_LSB_nV, - MAX9611_CSA_8X_OFFS_RAW, - }, + [CSA_GAIN_1x] = { MAX9611_CSA_1X_LSB_nV, MAX9611_CSA_1X_OFFS_RAW, }, + [CSA_GAIN_4x] = { MAX9611_CSA_4X_LSB_nV, MAX9611_CSA_4X_OFFS_RAW, }, + [CSA_GAIN_8x] = { MAX9611_CSA_8X_LSB_nV, MAX9611_CSA_8X_OFFS_RAW, }, }; enum max9611_chan_addrs { diff --git a/drivers/iio/adc/stm32-adc-core.c b/drivers/iio/adc/stm32-adc-core.c index 6537f4f776c5..2df88d2b880a 100644 --- a/drivers/iio/adc/stm32-adc-core.c +++ b/drivers/iio/adc/stm32-adc-core.c @@ -280,21 +280,21 @@ out: static const struct stm32_adc_common_regs stm32f4_adc_common_regs = { .csr = STM32F4_ADC_CSR, .ccr = STM32F4_ADC_CCR, - .eoc1_msk = STM32F4_EOC1, - .eoc2_msk = STM32F4_EOC2, - .eoc3_msk = STM32F4_EOC3, + .eoc1_msk = STM32F4_EOC1 | STM32F4_OVR1, + .eoc2_msk = STM32F4_EOC2 | STM32F4_OVR2, + .eoc3_msk = STM32F4_EOC3 | STM32F4_OVR3, .ier = STM32F4_ADC_CR1, - .eocie_msk = STM32F4_EOCIE, + .eocie_msk = STM32F4_EOCIE | STM32F4_OVRIE, }; /* STM32H7 common registers definitions */ static const struct stm32_adc_common_regs stm32h7_adc_common_regs = { .csr = STM32H7_ADC_CSR, .ccr = STM32H7_ADC_CCR, - .eoc1_msk = STM32H7_EOC_MST, - .eoc2_msk = STM32H7_EOC_SLV, + .eoc1_msk = STM32H7_EOC_MST | STM32H7_OVR_MST, + .eoc2_msk = STM32H7_EOC_SLV | STM32H7_OVR_SLV, .ier = STM32H7_ADC_IER, - .eocie_msk = STM32H7_EOCIE, + .eocie_msk = STM32H7_EOCIE | STM32H7_OVRIE, }; static const unsigned int stm32_adc_offset[STM32_ADC_MAX_ADCS] = { @@ -688,7 +688,8 @@ static int stm32_adc_probe(struct platform_device *pdev) priv->vref = devm_regulator_get(&pdev->dev, "vref"); if (IS_ERR(priv->vref)) { ret = PTR_ERR(priv->vref); - dev_err(&pdev->dev, "vref get failed, %d\n", ret); + if (ret != -EPROBE_DEFER) + dev_err(&pdev->dev, "vref get failed, %d\n", ret); return ret; } @@ -696,7 +697,8 @@ static int stm32_adc_probe(struct platform_device *pdev) if (IS_ERR(priv->aclk)) { ret = PTR_ERR(priv->aclk); if (ret != -ENOENT) { - dev_err(&pdev->dev, "Can't get 'adc' clock\n"); + if (ret != -EPROBE_DEFER) + dev_err(&pdev->dev, "Can't get 'adc' clock\n"); return ret; } priv->aclk = NULL; @@ -706,7 +708,8 @@ static int stm32_adc_probe(struct platform_device *pdev) if (IS_ERR(priv->bclk)) { ret = PTR_ERR(priv->bclk); if (ret != -ENOENT) { - dev_err(&pdev->dev, "Can't get 'bus' clock\n"); + if (ret != -EPROBE_DEFER) + dev_err(&pdev->dev, "Can't get 'bus' clock\n"); return ret; } priv->bclk = NULL; diff --git a/drivers/iio/adc/stm32-adc-core.h b/drivers/iio/adc/stm32-adc-core.h index 2579d514c2a3..2322809bfd2f 100644 --- a/drivers/iio/adc/stm32-adc-core.h +++ b/drivers/iio/adc/stm32-adc-core.h @@ -51,10 +51,12 @@ #define STM32F4_ADC_CCR (STM32_ADCX_COMN_OFFSET + 0x04) /* STM32F4_ADC_SR - bit fields */ +#define STM32F4_OVR BIT(5) #define STM32F4_STRT BIT(4) #define STM32F4_EOC BIT(1) /* STM32F4_ADC_CR1 - bit fields */ +#define STM32F4_OVRIE BIT(26) #define STM32F4_RES_SHIFT 24 #define STM32F4_RES_MASK GENMASK(25, 24) #define STM32F4_SCAN BIT(8) @@ -72,8 +74,11 @@ #define STM32F4_ADON BIT(0) /* STM32F4_ADC_CSR - bit fields */ +#define STM32F4_OVR3 BIT(21) #define STM32F4_EOC3 BIT(17) +#define STM32F4_OVR2 BIT(13) #define STM32F4_EOC2 BIT(9) +#define STM32F4_OVR1 BIT(5) #define STM32F4_EOC1 BIT(1) /* STM32F4_ADC_CCR - bit fields */ @@ -103,10 +108,12 @@ /* STM32H7_ADC_ISR - bit fields */ #define STM32MP1_VREGREADY BIT(12) +#define STM32H7_OVR BIT(4) #define STM32H7_EOC BIT(2) #define STM32H7_ADRDY BIT(0) /* STM32H7_ADC_IER - bit fields */ +#define STM32H7_OVRIE STM32H7_OVR #define STM32H7_EOCIE STM32H7_EOC /* STM32H7_ADC_CR - bit fields */ @@ -155,7 +162,9 @@ enum stm32h7_adc_dmngt { #define STM32H7_LINCALFACT_MASK GENMASK(29, 0) /* STM32H7_ADC_CSR - bit fields */ +#define STM32H7_OVR_SLV BIT(20) #define STM32H7_EOC_SLV BIT(18) +#define STM32H7_OVR_MST BIT(4) #define STM32H7_EOC_MST BIT(2) /* STM32H7_ADC_CCR - bit fields */ diff --git a/drivers/iio/adc/stm32-adc.c b/drivers/iio/adc/stm32-adc.c index 3b291d72701c..80c3f963527b 100644 --- a/drivers/iio/adc/stm32-adc.c +++ b/drivers/iio/adc/stm32-adc.c @@ -117,7 +117,9 @@ struct stm32_adc_regs { * struct stm32_adc_regspec - stm32 registers definition * @dr: data register offset * @ier_eoc: interrupt enable register & eocie bitfield + * @ier_ovr: interrupt enable register & overrun bitfield * @isr_eoc: interrupt status register & eoc bitfield + * @isr_ovr: interrupt status register & overrun bitfield * @sqr: reference to sequence registers array * @exten: trigger control register & bitfield * @extsel: trigger selection register & bitfield @@ -128,7 +130,9 @@ struct stm32_adc_regs { struct stm32_adc_regspec { const u32 dr; const struct stm32_adc_regs ier_eoc; + const struct stm32_adc_regs ier_ovr; const struct stm32_adc_regs isr_eoc; + const struct stm32_adc_regs isr_ovr; const struct stm32_adc_regs *sqr; const struct stm32_adc_regs exten; const struct stm32_adc_regs extsel; @@ -337,7 +341,9 @@ static const unsigned int stm32f4_adc_smp_cycles[STM32_ADC_MAX_SMP + 1] = { static const struct stm32_adc_regspec stm32f4_adc_regspec = { .dr = STM32F4_ADC_DR, .ier_eoc = { STM32F4_ADC_CR1, STM32F4_EOCIE }, + .ier_ovr = { STM32F4_ADC_CR1, STM32F4_OVRIE }, .isr_eoc = { STM32F4_ADC_SR, STM32F4_EOC }, + .isr_ovr = { STM32F4_ADC_SR, STM32F4_OVR }, .sqr = stm32f4_sq, .exten = { STM32F4_ADC_CR2, STM32F4_EXTEN_MASK, STM32F4_EXTEN_SHIFT }, .extsel = { STM32F4_ADC_CR2, STM32F4_EXTSEL_MASK, @@ -429,7 +435,9 @@ static const unsigned int stm32h7_adc_smp_cycles[STM32_ADC_MAX_SMP + 1] = { static const struct stm32_adc_regspec stm32h7_adc_regspec = { .dr = STM32H7_ADC_DR, .ier_eoc = { STM32H7_ADC_IER, STM32H7_EOCIE }, + .ier_ovr = { STM32H7_ADC_IER, STM32H7_OVRIE }, .isr_eoc = { STM32H7_ADC_ISR, STM32H7_EOC }, + .isr_ovr = { STM32H7_ADC_ISR, STM32H7_OVR }, .sqr = stm32h7_sq, .exten = { STM32H7_ADC_CFGR, STM32H7_EXTEN_MASK, STM32H7_EXTEN_SHIFT }, .extsel = { STM32H7_ADC_CFGR, STM32H7_EXTSEL_MASK, @@ -506,6 +514,18 @@ static void stm32_adc_conv_irq_disable(struct stm32_adc *adc) adc->cfg->regs->ier_eoc.mask); } +static void stm32_adc_ovr_irq_enable(struct stm32_adc *adc) +{ + stm32_adc_set_bits(adc, adc->cfg->regs->ier_ovr.reg, + adc->cfg->regs->ier_ovr.mask); +} + +static void stm32_adc_ovr_irq_disable(struct stm32_adc *adc) +{ + stm32_adc_clr_bits(adc, adc->cfg->regs->ier_ovr.reg, + adc->cfg->regs->ier_ovr.mask); +} + static void stm32_adc_set_res(struct stm32_adc *adc) { const struct stm32_adc_regs *res = &adc->cfg->regs->res; @@ -1205,6 +1225,19 @@ static int stm32_adc_read_raw(struct iio_dev *indio_dev, } } +static irqreturn_t stm32_adc_threaded_isr(int irq, void *data) +{ + struct stm32_adc *adc = data; + struct iio_dev *indio_dev = iio_priv_to_dev(adc); + const struct stm32_adc_regspec *regs = adc->cfg->regs; + u32 status = stm32_adc_readl(adc, regs->isr_eoc.reg); + + if (status & regs->isr_ovr.mask) + dev_err(&indio_dev->dev, "Overrun, stopping: restart needed\n"); + + return IRQ_HANDLED; +} + static irqreturn_t stm32_adc_isr(int irq, void *data) { struct stm32_adc *adc = data; @@ -1212,6 +1245,19 @@ static irqreturn_t stm32_adc_isr(int irq, void *data) const struct stm32_adc_regspec *regs = adc->cfg->regs; u32 status = stm32_adc_readl(adc, regs->isr_eoc.reg); + if (status & regs->isr_ovr.mask) { + /* + * Overrun occurred on regular conversions: data for wrong + * channel may be read. Unconditionally disable interrupts + * to stop processing data and print error message. + * Restarting the capture can be done by disabling, then + * re-enabling it (e.g. write 0, then 1 to buffer/enable). + */ + stm32_adc_ovr_irq_disable(adc); + stm32_adc_conv_irq_disable(adc); + return IRQ_WAKE_THREAD; + } + if (status & regs->isr_eoc.mask) { /* Reading DR also clears EOC status flag */ adc->buffer[adc->bufi] = stm32_adc_readw(adc, regs->dr); @@ -1441,6 +1487,8 @@ static int __stm32_adc_buffer_postenable(struct iio_dev *indio_dev) /* Reset adc buffer index */ adc->bufi = 0; + stm32_adc_ovr_irq_enable(adc); + if (!adc->dma_chan) stm32_adc_conv_irq_enable(adc); @@ -1481,6 +1529,8 @@ static void __stm32_adc_buffer_predisable(struct iio_dev *indio_dev) if (!adc->dma_chan) stm32_adc_conv_irq_disable(adc); + stm32_adc_ovr_irq_disable(adc); + if (adc->dma_chan) dmaengine_terminate_sync(adc->dma_chan); @@ -1746,9 +1796,21 @@ static int stm32_adc_dma_request(struct iio_dev *indio_dev) struct dma_slave_config config; int ret; - adc->dma_chan = dma_request_slave_channel(&indio_dev->dev, "rx"); - if (!adc->dma_chan) + adc->dma_chan = dma_request_chan(&indio_dev->dev, "rx"); + if (IS_ERR(adc->dma_chan)) { + ret = PTR_ERR(adc->dma_chan); + if (ret != -ENODEV) { + if (ret != -EPROBE_DEFER) + dev_err(&indio_dev->dev, + "DMA channel request failed with %d\n", + ret); + return ret; + } + + /* DMA is optional: fall back to IRQ mode */ + adc->dma_chan = NULL; return 0; + } adc->rx_buf = dma_alloc_coherent(adc->dma_chan->device->dev, STM32_DMA_BUFFER_SIZE, @@ -1818,8 +1880,9 @@ static int stm32_adc_probe(struct platform_device *pdev) if (adc->irq < 0) return adc->irq; - ret = devm_request_irq(&pdev->dev, adc->irq, stm32_adc_isr, - 0, pdev->name, adc); + ret = devm_request_threaded_irq(&pdev->dev, adc->irq, stm32_adc_isr, + stm32_adc_threaded_isr, + 0, pdev->name, adc); if (ret) { dev_err(&pdev->dev, "failed to request IRQ\n"); return ret; diff --git a/drivers/iio/adc/stm32-dfsdm-adc.c b/drivers/iio/adc/stm32-dfsdm-adc.c index e493242c266e..2aad2cda6943 100644 --- a/drivers/iio/adc/stm32-dfsdm-adc.c +++ b/drivers/iio/adc/stm32-dfsdm-adc.c @@ -1204,6 +1204,8 @@ static int stm32_dfsdm_single_conv(struct iio_dev *indio_dev, stm32_dfsdm_stop_conv(adc); + stm32_dfsdm_process_data(adc, res); + stop_dfsdm: stm32_dfsdm_stop_dfsdm(adc->dfsdm); @@ -1219,14 +1221,32 @@ static int stm32_dfsdm_write_raw(struct iio_dev *indio_dev, unsigned int spi_freq; int ret = -EINVAL; + switch (ch->src) { + case DFSDM_CHANNEL_SPI_CLOCK_INTERNAL: + spi_freq = adc->dfsdm->spi_master_freq; + break; + case DFSDM_CHANNEL_SPI_CLOCK_INTERNAL_DIV2_FALLING: + case DFSDM_CHANNEL_SPI_CLOCK_INTERNAL_DIV2_RISING: + spi_freq = adc->dfsdm->spi_master_freq / 2; + break; + default: + spi_freq = adc->spi_freq; + } + switch (mask) { case IIO_CHAN_INFO_OVERSAMPLING_RATIO: ret = iio_device_claim_direct_mode(indio_dev); if (ret) return ret; + ret = stm32_dfsdm_compute_all_osrs(indio_dev, val); - if (!ret) + if (!ret) { + dev_dbg(&indio_dev->dev, + "Sampling rate changed from (%u) to (%u)\n", + adc->sample_freq, spi_freq / val); adc->oversamp = val; + adc->sample_freq = spi_freq / val; + } iio_device_release_direct_mode(indio_dev); return ret; @@ -1238,18 +1258,6 @@ static int stm32_dfsdm_write_raw(struct iio_dev *indio_dev, if (ret) return ret; - switch (ch->src) { - case DFSDM_CHANNEL_SPI_CLOCK_INTERNAL: - spi_freq = adc->dfsdm->spi_master_freq; - break; - case DFSDM_CHANNEL_SPI_CLOCK_INTERNAL_DIV2_FALLING: - case DFSDM_CHANNEL_SPI_CLOCK_INTERNAL_DIV2_RISING: - spi_freq = adc->dfsdm->spi_master_freq / 2; - break; - default: - spi_freq = adc->spi_freq; - } - ret = dfsdm_adc_set_samp_freq(indio_dev, val, spi_freq); iio_device_release_direct_mode(indio_dev); return ret; @@ -1383,9 +1391,13 @@ static int stm32_dfsdm_dma_request(struct iio_dev *indio_dev) { struct stm32_dfsdm_adc *adc = iio_priv(indio_dev); - adc->dma_chan = dma_request_slave_channel(&indio_dev->dev, "rx"); - if (!adc->dma_chan) - return -EINVAL; + adc->dma_chan = dma_request_chan(&indio_dev->dev, "rx"); + if (IS_ERR(adc->dma_chan)) { + int ret = PTR_ERR(adc->dma_chan); + + adc->dma_chan = NULL; + return ret; + } adc->rx_buf = dma_alloc_coherent(adc->dma_chan->device->dev, DFSDM_DMA_BUFFER_SIZE, @@ -1509,7 +1521,16 @@ static int stm32_dfsdm_adc_init(struct iio_dev *indio_dev) init_completion(&adc->completion); /* Optionally request DMA */ - if (stm32_dfsdm_dma_request(indio_dev)) { + ret = stm32_dfsdm_dma_request(indio_dev); + if (ret) { + if (ret != -ENODEV) { + if (ret != -EPROBE_DEFER) + dev_err(&indio_dev->dev, + "DMA channel request failed with %d\n", + ret); + return ret; + } + dev_dbg(&indio_dev->dev, "No DMA support\n"); return 0; } diff --git a/drivers/iio/adc/ti-ads1015.c b/drivers/iio/adc/ti-ads1015.c index a550b132cfb7..5ea4f45d6bad 100644 --- a/drivers/iio/adc/ti-ads1015.c +++ b/drivers/iio/adc/ti-ads1015.c @@ -12,17 +12,15 @@ */ #include <linux/module.h> -#include <linux/of_device.h> #include <linux/init.h> #include <linux/irq.h> #include <linux/i2c.h> +#include <linux/property.h> #include <linux/regmap.h> #include <linux/pm_runtime.h> #include <linux/mutex.h> #include <linux/delay.h> -#include <linux/platform_data/ads1015.h> - #include <linux/iio/iio.h> #include <linux/iio/types.h> #include <linux/iio/sysfs.h> @@ -33,6 +31,8 @@ #define ADS1015_DRV_NAME "ads1015" +#define ADS1015_CHANNELS 8 + #define ADS1015_CONV_REG 0x00 #define ADS1015_CFG_REG 0x01 #define ADS1015_LO_THRESH_REG 0x02 @@ -77,6 +77,7 @@ #define ADS1015_DEFAULT_CHAN 0 enum chip_ids { + ADSXXXX = 0, ADS1015, ADS1115, }; @@ -219,6 +220,12 @@ static const struct iio_event_spec ads1015_events[] = { .datasheet_name = "AIN"#_chan"-AIN"#_chan2, \ } +struct ads1015_channel_data { + bool enabled; + unsigned int pga; + unsigned int data_rate; +}; + struct ads1015_thresh_data { unsigned int comp_queue; int high_thresh; @@ -837,65 +844,58 @@ static const struct iio_info ads1115_info = { .attrs = &ads1115_attribute_group, }; -#ifdef CONFIG_OF -static int ads1015_get_channels_config_of(struct i2c_client *client) +static int ads1015_client_get_channels_config(struct i2c_client *client) { struct iio_dev *indio_dev = i2c_get_clientdata(client); struct ads1015_data *data = iio_priv(indio_dev); - struct device_node *node; + struct device *dev = &client->dev; + struct fwnode_handle *node; + int i = -1; - if (!client->dev.of_node || - !of_get_next_child(client->dev.of_node, NULL)) - return -EINVAL; - - for_each_child_of_node(client->dev.of_node, node) { + device_for_each_child_node(dev, node) { u32 pval; unsigned int channel; unsigned int pga = ADS1015_DEFAULT_PGA; unsigned int data_rate = ADS1015_DEFAULT_DATA_RATE; - if (of_property_read_u32(node, "reg", &pval)) { - dev_err(&client->dev, "invalid reg on %pOF\n", - node); + if (fwnode_property_read_u32(node, "reg", &pval)) { + dev_err(dev, "invalid reg on %pfw\n", node); continue; } channel = pval; if (channel >= ADS1015_CHANNELS) { - dev_err(&client->dev, - "invalid channel index %d on %pOF\n", + dev_err(dev, "invalid channel index %d on %pfw\n", channel, node); continue; } - if (!of_property_read_u32(node, "ti,gain", &pval)) { + if (!fwnode_property_read_u32(node, "ti,gain", &pval)) { pga = pval; if (pga > 6) { - dev_err(&client->dev, "invalid gain on %pOF\n", - node); - of_node_put(node); + dev_err(dev, "invalid gain on %pfw\n", node); + fwnode_handle_put(node); return -EINVAL; } } - if (!of_property_read_u32(node, "ti,datarate", &pval)) { + if (!fwnode_property_read_u32(node, "ti,datarate", &pval)) { data_rate = pval; if (data_rate > 7) { - dev_err(&client->dev, - "invalid data_rate on %pOF\n", - node); - of_node_put(node); + dev_err(dev, "invalid data_rate on %pfw\n", node); + fwnode_handle_put(node); return -EINVAL; } } data->channel_data[channel].pga = pga; data->channel_data[channel].data_rate = data_rate; + + i++; } - return 0; + return i < 0 ? -EINVAL : 0; } -#endif static void ads1015_get_channels_config(struct i2c_client *client) { @@ -903,19 +903,10 @@ static void ads1015_get_channels_config(struct i2c_client *client) struct iio_dev *indio_dev = i2c_get_clientdata(client); struct ads1015_data *data = iio_priv(indio_dev); - struct ads1015_platform_data *pdata = dev_get_platdata(&client->dev); - /* prefer platform data */ - if (pdata) { - memcpy(data->channel_data, pdata->channel_data, - sizeof(data->channel_data)); + if (!ads1015_client_get_channels_config(client)) return; - } -#ifdef CONFIG_OF - if (!ads1015_get_channels_config_of(client)) - return; -#endif /* fallback on default configuration */ for (k = 0; k < ADS1015_CHANNELS; ++k) { data->channel_data[k].pga = ADS1015_DEFAULT_PGA; @@ -953,9 +944,8 @@ static int ads1015_probe(struct i2c_client *client, indio_dev->name = ADS1015_DRV_NAME; indio_dev->modes = INDIO_DIRECT_MODE; - if (client->dev.of_node) - chip = (enum chip_ids)of_device_get_match_data(&client->dev); - else + chip = (enum chip_ids)device_get_match_data(&client->dev); + if (chip == ADSXXXX) chip = id->driver_data; switch (chip) { case ADS1015: @@ -970,6 +960,9 @@ static int ads1015_probe(struct i2c_client *client, indio_dev->info = &ads1115_info; data->data_rate = (unsigned int *) &ads1115_data_rate; break; + default: + dev_err(&client->dev, "Unknown chip %d\n", chip); + return -EINVAL; } data->event_channel = ADS1015_CHANNELS; diff --git a/drivers/iio/adc/ti-ads7950.c b/drivers/iio/adc/ti-ads7950.c index 2e66e4d586ff..f9edc1207f75 100644 --- a/drivers/iio/adc/ti-ads7950.c +++ b/drivers/iio/adc/ti-ads7950.c @@ -602,7 +602,7 @@ static int ti_ads7950_probe(struct spi_device *spi) st->reg = devm_regulator_get(&spi->dev, "vref"); if (IS_ERR(st->reg)) { - dev_err(&spi->dev, "Failed get get regulator \"vref\"\n"); + dev_err(&spi->dev, "Failed to get regulator \"vref\"\n"); ret = PTR_ERR(st->reg); goto error_destroy_mutex; } diff --git a/drivers/iio/buffer/industrialio-buffer-dma.c b/drivers/iio/buffer/industrialio-buffer-dma.c index 90cf6e586b10..a74bd9c0587c 100644 --- a/drivers/iio/buffer/industrialio-buffer-dma.c +++ b/drivers/iio/buffer/industrialio-buffer-dma.c @@ -476,7 +476,7 @@ static struct iio_dma_buffer_block *iio_dma_buffer_dequeue( * @n: Number of bytes to read * @user_buffer: Userspace buffer to copy the data to * - * Should be used as the read_first_n callback for iio_buffer_access_ops + * Should be used as the read callback for iio_buffer_access_ops * struct for DMA buffers. */ int iio_dma_buffer_read(struct iio_buffer *buffer, size_t n, diff --git a/drivers/iio/buffer/industrialio-buffer-dmaengine.c b/drivers/iio/buffer/industrialio-buffer-dmaengine.c index bea4a75e92f1..b129693af0fd 100644 --- a/drivers/iio/buffer/industrialio-buffer-dmaengine.c +++ b/drivers/iio/buffer/industrialio-buffer-dmaengine.c @@ -10,8 +10,10 @@ #include <linux/dma-mapping.h> #include <linux/spinlock.h> #include <linux/err.h> +#include <linux/module.h> #include <linux/iio/iio.h> +#include <linux/iio/sysfs.h> #include <linux/iio/buffer.h> #include <linux/iio/buffer_impl.h> #include <linux/iio/buffer-dma.h> @@ -107,7 +109,7 @@ static void iio_dmaengine_buffer_release(struct iio_buffer *buf) } static const struct iio_buffer_access_funcs iio_dmaengine_buffer_ops = { - .read_first_n = iio_dma_buffer_read, + .read = iio_dma_buffer_read, .set_bytes_per_datum = iio_dma_buffer_set_bytes_per_datum, .set_length = iio_dma_buffer_set_length, .request_update = iio_dma_buffer_request_update, @@ -125,6 +127,24 @@ static const struct iio_dma_buffer_ops iio_dmaengine_default_ops = { .abort = iio_dmaengine_buffer_abort, }; +static ssize_t iio_dmaengine_buffer_get_length_align(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct iio_dev *indio_dev = dev_to_iio_dev(dev); + struct dmaengine_buffer *dmaengine_buffer = + iio_buffer_to_dmaengine_buffer(indio_dev->buffer); + + return sprintf(buf, "%u\n", dmaengine_buffer->align); +} + +static IIO_DEVICE_ATTR(length_align_bytes, 0444, + iio_dmaengine_buffer_get_length_align, NULL, 0); + +static const struct attribute *iio_dmaengine_buffer_attrs[] = { + &iio_dev_attr_length_align_bytes.dev_attr.attr, + NULL, +}; + /** * iio_dmaengine_buffer_alloc() - Allocate new buffer which uses DMAengine * @dev: Parent device for the buffer @@ -150,7 +170,7 @@ struct iio_buffer *iio_dmaengine_buffer_alloc(struct device *dev, if (!dmaengine_buffer) return ERR_PTR(-ENOMEM); - chan = dma_request_slave_channel_reason(dev, channel); + chan = dma_request_chan(dev, channel); if (IS_ERR(chan)) { ret = PTR_ERR(chan); goto err_free; @@ -178,6 +198,8 @@ struct iio_buffer *iio_dmaengine_buffer_alloc(struct device *dev, iio_dma_buffer_init(&dmaengine_buffer->queue, chan->device->dev, &iio_dmaengine_default_ops); + iio_buffer_set_attrs(&dmaengine_buffer->queue.buffer, + iio_dmaengine_buffer_attrs); dmaengine_buffer->queue.buffer.access = &iio_dmaengine_buffer_ops; @@ -206,3 +228,7 @@ void iio_dmaengine_buffer_free(struct iio_buffer *buffer) iio_buffer_put(buffer); } EXPORT_SYMBOL_GPL(iio_dmaengine_buffer_free); + +MODULE_AUTHOR("Lars-Peter Clausen <lars@metafoo.de>"); +MODULE_DESCRIPTION("DMA buffer for the IIO framework"); +MODULE_LICENSE("GPL"); diff --git a/drivers/iio/buffer/kfifo_buf.c b/drivers/iio/buffer/kfifo_buf.c index e78fc0834e6b..3150f8ab984b 100644 --- a/drivers/iio/buffer/kfifo_buf.c +++ b/drivers/iio/buffer/kfifo_buf.c @@ -98,8 +98,7 @@ static int iio_store_to_kfifo(struct iio_buffer *r, return 0; } -static int iio_read_first_n_kfifo(struct iio_buffer *r, - size_t n, char __user *buf) +static int iio_read_kfifo(struct iio_buffer *r, size_t n, char __user *buf) { int ret, copied; struct iio_kfifo *kf = iio_to_kfifo(r); @@ -141,7 +140,7 @@ static void iio_kfifo_buffer_release(struct iio_buffer *buffer) static const struct iio_buffer_access_funcs kfifo_access_funcs = { .store_to = &iio_store_to_kfifo, - .read_first_n = &iio_read_first_n_kfifo, + .read = &iio_read_kfifo, .data_available = iio_kfifo_buf_data_available, .request_update = &iio_request_update_kfifo, .set_bytes_per_datum = &iio_set_bytes_per_datum_kfifo, diff --git a/drivers/iio/chemical/Makefile b/drivers/iio/chemical/Makefile index f97270bc4034..33d3a595dda9 100644 --- a/drivers/iio/chemical/Makefile +++ b/drivers/iio/chemical/Makefile @@ -4,7 +4,7 @@ # # When adding new entries keep the list in alphabetical order -obj-$(CONFIG_ATLAS_PH_SENSOR) += atlas-ph-sensor.o +obj-$(CONFIG_ATLAS_PH_SENSOR) += atlas-sensor.o obj-$(CONFIG_BME680) += bme680_core.o obj-$(CONFIG_BME680_I2C) += bme680_i2c.o obj-$(CONFIG_BME680_SPI) += bme680_spi.o diff --git a/drivers/iio/chemical/atlas-ph-sensor.c b/drivers/iio/chemical/atlas-sensor.c index 6c175eb1c7a7..2f0a6fed2589 100644 --- a/drivers/iio/chemical/atlas-ph-sensor.c +++ b/drivers/iio/chemical/atlas-sensor.c @@ -1,8 +1,8 @@ // SPDX-License-Identifier: GPL-2.0+ /* - * atlas-ph-sensor.c - Support for Atlas Scientific OEM pH-SM sensor + * atlas-sensor.c - Support for Atlas Scientific OEM SM sensors * - * Copyright (C) 2015-2018 Matt Ranostay + * Copyright (C) 2015-2019 Konsulko Group * Author: Matt Ranostay <matt.ranostay@konsulko.com> */ @@ -14,7 +14,6 @@ #include <linux/err.h> #include <linux/irq.h> #include <linux/irq_work.h> -#include <linux/gpio.h> #include <linux/i2c.h> #include <linux/of_device.h> #include <linux/regmap.h> @@ -25,8 +24,8 @@ #include <linux/iio/triggered_buffer.h> #include <linux/pm_runtime.h> -#define ATLAS_REGMAP_NAME "atlas_ph_regmap" -#define ATLAS_DRV_NAME "atlas_ph" +#define ATLAS_REGMAP_NAME "atlas_regmap" +#define ATLAS_DRV_NAME "atlas" #define ATLAS_REG_DEV_TYPE 0x00 #define ATLAS_REG_DEV_VERSION 0x01 @@ -87,6 +86,16 @@ static const struct regmap_config atlas_regmap_config = { .val_bits = 8, }; +static int atlas_buffer_num_channels(const struct iio_chan_spec *spec) +{ + int idx = 0; + + for (; spec->type != IIO_TIMESTAMP; spec++) + idx++; + + return idx; +}; + static const struct iio_chan_spec atlas_ph_channels[] = { { .type = IIO_PH, @@ -355,11 +364,12 @@ static irqreturn_t atlas_trigger_handler(int irq, void *private) struct iio_poll_func *pf = private; struct iio_dev *indio_dev = pf->indio_dev; struct atlas_data *data = iio_priv(indio_dev); + int channels = atlas_buffer_num_channels(data->chip->channels); int ret; ret = regmap_bulk_read(data->regmap, data->chip->data_reg, (u8 *) &data->buffer, - sizeof(__be32) * (data->chip->num_channels - 2)); + sizeof(__be32) * channels); if (!ret) iio_push_to_buffers_with_timestamp(indio_dev, data->buffer, @@ -681,5 +691,5 @@ static struct i2c_driver atlas_driver = { module_i2c_driver(atlas_driver); MODULE_AUTHOR("Matt Ranostay <matt.ranostay@konsulko.com>"); -MODULE_DESCRIPTION("Atlas Scientific pH-SM sensor"); +MODULE_DESCRIPTION("Atlas Scientific SM sensors"); MODULE_LICENSE("GPL"); diff --git a/drivers/iio/common/ssp_sensors/ssp.h b/drivers/iio/common/ssp_sensors/ssp.h index 0a381bb1ae6f..abb832795619 100644 --- a/drivers/iio/common/ssp_sensors/ssp.h +++ b/drivers/iio/common/ssp_sensors/ssp.h @@ -7,7 +7,7 @@ #define __SSP_SENSORHUB_H__ #include <linux/delay.h> -#include <linux/gpio.h> +#include <linux/gpio/consumer.h> #include <linux/iio/common/ssp_sensors.h> #include <linux/iio/iio.h> #include <linux/spi/spi.h> @@ -168,9 +168,9 @@ struct ssp_sensorhub_info { * @fw_dl_state: firmware download state * @comm_lock: lock protecting the handshake * @pending_lock: lock protecting pending list and completion - * @mcu_reset_gpio: mcu reset line - * @ap_mcu_gpio: ap to mcu gpio line - * @mcu_ap_gpio: mcu to ap gpio line + * @mcu_reset_gpiod: mcu reset line + * @ap_mcu_gpiod: ap to mcu gpio line + * @mcu_ap_gpiod: mcu to ap gpio line * @pending_list: pending list for messages queued to be sent/read * @sensor_devs: registered IIO devices table * @enable_refcount: enable reference count for wdt (watchdog timer) @@ -212,9 +212,9 @@ struct ssp_data { struct mutex comm_lock; struct mutex pending_lock; - int mcu_reset_gpio; - int ap_mcu_gpio; - int mcu_ap_gpio; + struct gpio_desc *mcu_reset_gpiod; + struct gpio_desc *ap_mcu_gpiod; + struct gpio_desc *mcu_ap_gpiod; struct list_head pending_list; diff --git a/drivers/iio/common/ssp_sensors/ssp_dev.c b/drivers/iio/common/ssp_sensors/ssp_dev.c index 9c70553994c6..a94dbcf491ce 100644 --- a/drivers/iio/common/ssp_sensors/ssp_dev.c +++ b/drivers/iio/common/ssp_sensors/ssp_dev.c @@ -9,7 +9,6 @@ #include <linux/mfd/core.h> #include <linux/module.h> #include <linux/of.h> -#include <linux/of_gpio.h> #include <linux/of_platform.h> #include "ssp.h" @@ -61,9 +60,9 @@ static const struct mfd_cell sensorhub_sensor_devs[] = { static void ssp_toggle_mcu_reset_gpio(struct ssp_data *data) { - gpio_set_value(data->mcu_reset_gpio, 0); + gpiod_set_value(data->mcu_reset_gpiod, 0); usleep_range(1000, 1200); - gpio_set_value(data->mcu_reset_gpio, 1); + gpiod_set_value(data->mcu_reset_gpiod, 1); msleep(50); } @@ -441,7 +440,6 @@ MODULE_DEVICE_TABLE(of, ssp_of_match); static struct ssp_data *ssp_parse_dt(struct device *dev) { - int ret; struct ssp_data *data; struct device_node *node = dev->of_node; const struct of_device_id *match; @@ -450,26 +448,17 @@ static struct ssp_data *ssp_parse_dt(struct device *dev) if (!data) return NULL; - data->mcu_ap_gpio = of_get_named_gpio(node, "mcu-ap-gpios", 0); - if (data->mcu_ap_gpio < 0) - return NULL; - - data->ap_mcu_gpio = of_get_named_gpio(node, "ap-mcu-gpios", 0); - if (data->ap_mcu_gpio < 0) - return NULL; - - data->mcu_reset_gpio = of_get_named_gpio(node, "mcu-reset-gpios", 0); - if (data->mcu_reset_gpio < 0) + data->mcu_ap_gpiod = devm_gpiod_get(dev, "mcu-ap", GPIOD_IN); + if (IS_ERR(data->mcu_ap_gpiod)) return NULL; - ret = devm_gpio_request_one(dev, data->ap_mcu_gpio, GPIOF_OUT_INIT_HIGH, - "ap-mcu-gpios"); - if (ret) + data->ap_mcu_gpiod = devm_gpiod_get(dev, "ap-mcu", GPIOD_OUT_HIGH); + if (IS_ERR(data->ap_mcu_gpiod)) return NULL; - ret = devm_gpio_request_one(dev, data->mcu_reset_gpio, - GPIOF_OUT_INIT_HIGH, "mcu-reset-gpios"); - if (ret) + data->mcu_reset_gpiod = devm_gpiod_get(dev, "mcu-reset", + GPIOD_OUT_HIGH); + if (IS_ERR(data->mcu_reset_gpiod)) return NULL; match = of_match_node(ssp_of_match, node); diff --git a/drivers/iio/common/ssp_sensors/ssp_spi.c b/drivers/iio/common/ssp_sensors/ssp_spi.c index 7db3d5886e3e..4864c38b8d1c 100644 --- a/drivers/iio/common/ssp_sensors/ssp_spi.c +++ b/drivers/iio/common/ssp_sensors/ssp_spi.c @@ -155,9 +155,9 @@ static int ssp_check_lines(struct ssp_data *data, bool state) { int delay_cnt = 0; - gpio_set_value_cansleep(data->ap_mcu_gpio, state); + gpiod_set_value_cansleep(data->ap_mcu_gpiod, state); - while (gpio_get_value_cansleep(data->mcu_ap_gpio) != state) { + while (gpiod_get_value_cansleep(data->mcu_ap_gpiod) != state) { usleep_range(3000, 3500); if (data->shut_down || delay_cnt++ > 500) { @@ -165,7 +165,7 @@ static int ssp_check_lines(struct ssp_data *data, bool state) __func__, state); if (!state) - gpio_set_value_cansleep(data->ap_mcu_gpio, 1); + gpiod_set_value_cansleep(data->ap_mcu_gpiod, 1); return -ETIMEDOUT; } @@ -197,7 +197,7 @@ static int ssp_do_transfer(struct ssp_data *data, struct ssp_msg *msg, status = spi_write(data->spi, msg->buffer, SSP_HEADER_SIZE); if (status < 0) { - gpio_set_value_cansleep(data->ap_mcu_gpio, 1); + gpiod_set_value_cansleep(data->ap_mcu_gpiod, 1); dev_err(SSP_DEV, "%s spi_write fail\n", __func__); goto _error_locked; } diff --git a/drivers/iio/common/st_sensors/st_sensors_core.c b/drivers/iio/common/st_sensors/st_sensors_core.c index 4a3064fb6cd9..e051edbc43c1 100644 --- a/drivers/iio/common/st_sensors/st_sensors_core.c +++ b/drivers/iio/common/st_sensors/st_sensors_core.c @@ -12,9 +12,8 @@ #include <linux/slab.h> #include <linux/delay.h> #include <linux/iio/iio.h> +#include <linux/property.h> #include <linux/regulator/consumer.h> -#include <linux/of.h> -#include <linux/of_device.h> #include <linux/regmap.h> #include <asm/unaligned.h> #include <linux/iio/common/st_sensors.h> @@ -319,63 +318,49 @@ static int st_sensors_set_drdy_int_pin(struct iio_dev *indio_dev, return 0; } -#ifdef CONFIG_OF -static struct st_sensors_platform_data *st_sensors_of_probe(struct device *dev, +static struct st_sensors_platform_data *st_sensors_dev_probe(struct device *dev, struct st_sensors_platform_data *defdata) { struct st_sensors_platform_data *pdata; - struct device_node *np = dev->of_node; u32 val; - if (!np) + if (!dev_fwnode(dev)) return NULL; pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL); - if (!of_property_read_u32(np, "st,drdy-int-pin", &val) && (val <= 2)) + if (!device_property_read_u32(dev, "st,drdy-int-pin", &val) && (val <= 2)) pdata->drdy_int_pin = (u8) val; else pdata->drdy_int_pin = defdata ? defdata->drdy_int_pin : 0; - pdata->open_drain = of_property_read_bool(np, "drive-open-drain"); + pdata->open_drain = device_property_read_bool(dev, "drive-open-drain"); return pdata; } /** - * st_sensors_of_name_probe() - device tree probe for ST sensor name + * st_sensors_dev_name_probe() - device probe for ST sensor name * @dev: driver model representation of the device. - * @match: the OF match table for the device, containing compatible strings - * but also a .data field with the corresponding internal kernel name - * used by this sensor. * @name: device name buffer reference. * @len: device name buffer length. * - * In effect this function matches a compatible string to an internal kernel + * In effect this function matches an ID to an internal kernel * name for a certain sensor device, so that the rest of the autodetection can * rely on that name from this point on. I2C/SPI devices will be renamed * to match the internal kernel convention. */ -void st_sensors_of_name_probe(struct device *dev, - const struct of_device_id *match, - char *name, int len) +void st_sensors_dev_name_probe(struct device *dev, char *name, int len) { - const struct of_device_id *of_id; + const void *match; - of_id = of_match_device(match, dev); - if (!of_id || !of_id->data) + match = device_get_match_data(dev); + if (!match) return; - /* The name from the OF match takes precedence if present */ - strlcpy(name, of_id->data, len); + /* The name from the match takes precedence if present */ + strlcpy(name, match, len); } -EXPORT_SYMBOL(st_sensors_of_name_probe); -#else -static struct st_sensors_platform_data *st_sensors_of_probe(struct device *dev, - struct st_sensors_platform_data *defdata) -{ - return NULL; -} -#endif +EXPORT_SYMBOL(st_sensors_dev_name_probe); int st_sensors_init_sensor(struct iio_dev *indio_dev, struct st_sensors_platform_data *pdata) @@ -385,7 +370,7 @@ int st_sensors_init_sensor(struct iio_dev *indio_dev, int err = 0; /* If OF/DT pdata exists, it will take precedence of anything else */ - of_pdata = st_sensors_of_probe(indio_dev->dev.parent, pdata); + of_pdata = st_sensors_dev_probe(indio_dev->dev.parent, pdata); if (of_pdata) pdata = of_pdata; diff --git a/drivers/iio/common/st_sensors/st_sensors_i2c.c b/drivers/iio/common/st_sensors/st_sensors_i2c.c index aa89d54a7c59..286830fb5d35 100644 --- a/drivers/iio/common/st_sensors/st_sensors_i2c.c +++ b/drivers/iio/common/st_sensors/st_sensors_i2c.c @@ -11,8 +11,6 @@ #include <linux/module.h> #include <linux/slab.h> #include <linux/iio/iio.h> -#include <linux/of_device.h> -#include <linux/acpi.h> #include <linux/regmap.h> #include <linux/iio/common/st_sensors_i2c.h> @@ -68,25 +66,6 @@ int st_sensors_i2c_configure(struct iio_dev *indio_dev, } EXPORT_SYMBOL(st_sensors_i2c_configure); -#ifdef CONFIG_ACPI -int st_sensors_match_acpi_device(struct device *dev) -{ - const struct acpi_device_id *acpi_id; - kernel_ulong_t driver_data = 0; - - if (ACPI_HANDLE(dev)) { - acpi_id = acpi_match_device(dev->driver->acpi_match_table, dev); - if (!acpi_id) { - dev_err(dev, "No driver data\n"); - return -EINVAL; - } - driver_data = acpi_id->driver_data; - } - return driver_data; -} -EXPORT_SYMBOL(st_sensors_match_acpi_device); -#endif - MODULE_AUTHOR("Denis Ciocca <denis.ciocca@st.com>"); MODULE_DESCRIPTION("STMicroelectronics ST-sensors i2c driver"); MODULE_LICENSE("GPL v2"); diff --git a/drivers/iio/common/st_sensors/st_sensors_spi.c b/drivers/iio/common/st_sensors/st_sensors_spi.c index 2262f81b07c2..1275fb0eda31 100644 --- a/drivers/iio/common/st_sensors/st_sensors_spi.c +++ b/drivers/iio/common/st_sensors/st_sensors_spi.c @@ -11,6 +11,7 @@ #include <linux/module.h> #include <linux/slab.h> #include <linux/iio/iio.h> +#include <linux/property.h> #include <linux/regmap.h> #include <linux/iio/common/st_sensors_spi.h> @@ -37,14 +38,15 @@ static const struct regmap_config st_sensors_spi_regmap_multiread_bit_config = { */ static bool st_sensors_is_spi_3_wire(struct spi_device *spi) { - struct device_node *np = spi->dev.of_node; struct st_sensors_platform_data *pdata; + struct device *dev = &spi->dev; - pdata = (struct st_sensors_platform_data *)spi->dev.platform_data; - if ((np && of_property_read_bool(np, "spi-3wire")) || - (pdata && pdata->spi_3wire)) { + if (device_property_read_bool(dev, "spi-3wire")) + return true; + + pdata = (struct st_sensors_platform_data *)dev->platform_data; + if (pdata && pdata->spi_3wire) return true; - } return false; } diff --git a/drivers/iio/common/st_sensors/st_sensors_trigger.c b/drivers/iio/common/st_sensors/st_sensors_trigger.c index 4a2efa00f7f2..e817537cdfb5 100644 --- a/drivers/iio/common/st_sensors/st_sensors_trigger.c +++ b/drivers/iio/common/st_sensors/st_sensors_trigger.c @@ -19,6 +19,9 @@ /** * st_sensors_new_samples_available() - check if more samples came in + * @indio_dev: IIO device reference. + * @sdata: Sensor data. + * * returns: * 0 - no new samples available * 1 - new samples available diff --git a/drivers/iio/dac/ad5592r-base.c b/drivers/iio/dac/ad5592r-base.c index 2d897e64c6a9..e2110113e884 100644 --- a/drivers/iio/dac/ad5592r-base.c +++ b/drivers/iio/dac/ad5592r-base.c @@ -15,7 +15,6 @@ #include <linux/regulator/consumer.h> #include <linux/gpio/consumer.h> #include <linux/gpio/driver.h> -#include <linux/gpio.h> #include <linux/property.h> #include <dt-bindings/iio/adi,ad5592r.h> diff --git a/drivers/iio/dac/ad7303.c b/drivers/iio/dac/ad7303.c index 14bbac6bee98..15af8a1cce3e 100644 --- a/drivers/iio/dac/ad7303.c +++ b/drivers/iio/dac/ad7303.c @@ -12,7 +12,6 @@ #include <linux/slab.h> #include <linux/sysfs.h> #include <linux/regulator/consumer.h> -#include <linux/of.h> #include <linux/iio/iio.h> #include <linux/iio/sysfs.h> @@ -202,7 +201,6 @@ static int ad7303_probe(struct spi_device *spi) const struct spi_device_id *id = spi_get_device_id(spi); struct iio_dev *indio_dev; struct ad7303_state *st; - bool ext_ref; int ret; indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st)); @@ -224,24 +222,15 @@ static int ad7303_probe(struct spi_device *spi) if (ret) return ret; - if (spi->dev.of_node) { - ext_ref = of_property_read_bool(spi->dev.of_node, - "REF-supply"); - } else { - struct ad7303_platform_data *pdata = spi->dev.platform_data; - if (pdata && pdata->use_external_ref) - ext_ref = true; - else - ext_ref = false; - } - - if (ext_ref) { - st->vref_reg = devm_regulator_get(&spi->dev, "REF"); - if (IS_ERR(st->vref_reg)) { - ret = PTR_ERR(st->vref_reg); + st->vref_reg = devm_regulator_get_optional(&spi->dev, "REF"); + if (IS_ERR(st->vref_reg)) { + ret = PTR_ERR(st->vref_reg); + if (ret != -ENODEV) goto err_disable_vdd_reg; - } + st->vref_reg = NULL; + } + if (st->vref_reg) { ret = regulator_enable(st->vref_reg); if (ret) goto err_disable_vdd_reg; diff --git a/drivers/iio/dac/stm32-dac-core.c b/drivers/iio/dac/stm32-dac-core.c index 9e6b4cd0a5cc..7e5809ba0dee 100644 --- a/drivers/iio/dac/stm32-dac-core.c +++ b/drivers/iio/dac/stm32-dac-core.c @@ -20,13 +20,11 @@ /** * struct stm32_dac_priv - stm32 DAC core private data * @pclk: peripheral clock common for all DACs - * @rst: peripheral reset control * @vref: regulator reference * @common: Common data for all DAC instances */ struct stm32_dac_priv { struct clk *pclk; - struct reset_control *rst; struct regulator *vref; struct stm32_dac_common common; }; @@ -94,6 +92,7 @@ static int stm32_dac_probe(struct platform_device *pdev) struct regmap *regmap; struct resource *res; void __iomem *mmio; + struct reset_control *rst; int ret; if (!dev->of_node) @@ -148,11 +147,19 @@ static int stm32_dac_probe(struct platform_device *pdev) priv->common.vref_mv = ret / 1000; dev_dbg(dev, "vref+=%dmV\n", priv->common.vref_mv); - priv->rst = devm_reset_control_get_exclusive(dev, NULL); - if (!IS_ERR(priv->rst)) { - reset_control_assert(priv->rst); + rst = devm_reset_control_get_optional_exclusive(dev, NULL); + if (rst) { + if (IS_ERR(rst)) { + ret = PTR_ERR(rst); + if (ret != -EPROBE_DEFER) + dev_err(dev, "reset get failed, %d\n", ret); + + goto err_hw_stop; + } + + reset_control_assert(rst); udelay(2); - reset_control_deassert(priv->rst); + reset_control_deassert(rst); } if (cfg && cfg->has_hfsel) { diff --git a/drivers/iio/frequency/adf4350.c b/drivers/iio/frequency/adf4350.c index ae0ca09ae062..1c2dc9b00f31 100644 --- a/drivers/iio/frequency/adf4350.c +++ b/drivers/iio/frequency/adf4350.c @@ -14,11 +14,10 @@ #include <linux/err.h> #include <linux/module.h> #include <linux/gcd.h> -#include <linux/gpio.h> +#include <linux/gpio/consumer.h> #include <asm/div64.h> #include <linux/clk.h> #include <linux/of.h> -#include <linux/of_gpio.h> #include <linux/iio/iio.h> #include <linux/iio/sysfs.h> @@ -34,6 +33,7 @@ enum { struct adf4350_state { struct spi_device *spi; struct regulator *reg; + struct gpio_desc *lock_detect_gpiod; struct adf4350_platform_data *pdata; struct clk *clk; unsigned long clkin; @@ -61,7 +61,6 @@ static struct adf4350_platform_data default_pdata = { .r3_user_settings = ADF4350_REG3_12BIT_CLKDIV_MODE(0), .r4_user_settings = ADF4350_REG4_OUTPUT_PWR(3) | ADF4350_REG4_MUTE_TILL_LOCK_EN, - .gpio_lock_detect = -1, }; static int adf4350_sync_config(struct adf4350_state *st) @@ -317,8 +316,8 @@ static ssize_t adf4350_read(struct iio_dev *indio_dev, (u64)st->fpfd; do_div(val, st->r1_mod * (1 << st->r4_rf_div_sel)); /* PLL unlocked? return error */ - if (gpio_is_valid(st->pdata->gpio_lock_detect)) - if (!gpio_get_value(st->pdata->gpio_lock_detect)) { + if (st->lock_detect_gpiod) + if (!gpiod_get_value(st->lock_detect_gpiod)) { dev_dbg(&st->spi->dev, "PLL un-locked\n"); ret = -EBUSY; } @@ -381,7 +380,6 @@ static struct adf4350_platform_data *adf4350_parse_dt(struct device *dev) struct device_node *np = dev->of_node; struct adf4350_platform_data *pdata; unsigned int tmp; - int ret; pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL); if (!pdata) @@ -401,12 +399,6 @@ static struct adf4350_platform_data *adf4350_parse_dt(struct device *dev) of_property_read_u32(np, "adi,reference-div-factor", &tmp); pdata->ref_div_factor = tmp; - ret = of_get_gpio(np, 0); - if (ret < 0) - pdata->gpio_lock_detect = -1; - else - pdata->gpio_lock_detect = ret; - pdata->ref_doubler_en = of_property_read_bool(np, "adi,reference-doubler-enable"); pdata->ref_div2_en = of_property_read_bool(np, @@ -561,16 +553,10 @@ static int adf4350_probe(struct spi_device *spi) memset(st->regs_hw, 0xFF, sizeof(st->regs_hw)); - if (gpio_is_valid(pdata->gpio_lock_detect)) { - ret = devm_gpio_request(&spi->dev, pdata->gpio_lock_detect, - indio_dev->name); - if (ret) { - dev_err(&spi->dev, "fail to request lock detect GPIO-%d", - pdata->gpio_lock_detect); - goto error_disable_reg; - } - gpio_direction_input(pdata->gpio_lock_detect); - } + st->lock_detect_gpiod = devm_gpiod_get_optional(&spi->dev, NULL, + GPIOD_IN); + if (IS_ERR(st->lock_detect_gpiod)) + return PTR_ERR(st->lock_detect_gpiod); if (pdata->power_up_frequency) { ret = adf4350_set_freq(st, pdata->power_up_frequency); diff --git a/drivers/iio/gyro/Kconfig b/drivers/iio/gyro/Kconfig index 95e6f96d4529..7eaf77707b0b 100644 --- a/drivers/iio/gyro/Kconfig +++ b/drivers/iio/gyro/Kconfig @@ -75,26 +75,26 @@ config BMG160_SPI select REGMAP_SPI config FXAS21002C - tristate "NXP FXAS21002C Gyro Sensor" - select IIO_BUFFER - select IIO_TRIGGERED_BUFFER - select FXAS21002C_I2C if (I2C) - select FXAS21002C_SPI if (SPI) - depends on (I2C || SPI_MASTER) - help - Say yes here to build support for NXP FXAS21002C Tri-axis Gyro - Sensor driver connected via I2C or SPI. - - This driver can also be built as a module. If so, the module - will be called fxas21002c_i2c or fxas21002c_spi. + tristate "NXP FXAS21002C Gyro Sensor" + select IIO_BUFFER + select IIO_TRIGGERED_BUFFER + select FXAS21002C_I2C if (I2C) + select FXAS21002C_SPI if (SPI) + depends on (I2C || SPI_MASTER) + help + Say yes here to build support for NXP FXAS21002C Tri-axis Gyro + Sensor driver connected via I2C or SPI. + + This driver can also be built as a module. If so, the module + will be called fxas21002c_i2c or fxas21002c_spi. config FXAS21002C_I2C - tristate - select REGMAP_I2C + tristate + select REGMAP_I2C config FXAS21002C_SPI - tristate - select REGMAP_SPI + tristate + select REGMAP_SPI config HID_SENSOR_GYRO_3D depends on HID_SENSOR_HUB diff --git a/drivers/iio/gyro/adis16136.c b/drivers/iio/gyro/adis16136.c index d637d52d051a..d5e03a406d4a 100644 --- a/drivers/iio/gyro/adis16136.c +++ b/drivers/iio/gyro/adis16136.c @@ -59,6 +59,7 @@ struct adis16136_chip_info { unsigned int precision; unsigned int fullscale; + const struct adis_timeout *timeouts; }; struct adis16136 { @@ -185,12 +186,12 @@ static int adis16136_set_freq(struct adis16136 *adis16136, unsigned int freq) return adis_write_reg_16(&adis16136->adis, ADIS16136_REG_SMPL_PRD, t); } -static int adis16136_get_freq(struct adis16136 *adis16136, unsigned int *freq) +static int __adis16136_get_freq(struct adis16136 *adis16136, unsigned int *freq) { uint16_t t; int ret; - ret = adis_read_reg_16(&adis16136->adis, ADIS16136_REG_SMPL_PRD, &t); + ret = __adis_read_reg_16(&adis16136->adis, ADIS16136_REG_SMPL_PRD, &t); if (ret) return ret; @@ -224,10 +225,13 @@ static ssize_t adis16136_read_frequency(struct device *dev, { struct iio_dev *indio_dev = dev_to_iio_dev(dev); struct adis16136 *adis16136 = iio_priv(indio_dev); + struct mutex *slock = &adis16136->adis.state_lock; unsigned int freq; int ret; - ret = adis16136_get_freq(adis16136, &freq); + mutex_lock(slock); + ret = __adis16136_get_freq(adis16136, &freq); + mutex_unlock(slock); if (ret) return ret; @@ -252,42 +256,50 @@ static const unsigned adis16136_3db_divisors[] = { static int adis16136_set_filter(struct iio_dev *indio_dev, int val) { struct adis16136 *adis16136 = iio_priv(indio_dev); + struct mutex *slock = &adis16136->adis.state_lock; unsigned int freq; int i, ret; - ret = adis16136_get_freq(adis16136, &freq); + mutex_lock(slock); + ret = __adis16136_get_freq(adis16136, &freq); if (ret) - return ret; + goto out_unlock; for (i = ARRAY_SIZE(adis16136_3db_divisors) - 1; i >= 1; i--) { if (freq / adis16136_3db_divisors[i] >= val) break; } - return adis_write_reg_16(&adis16136->adis, ADIS16136_REG_AVG_CNT, i); + ret = __adis_write_reg_16(&adis16136->adis, ADIS16136_REG_AVG_CNT, i); +out_unlock: + mutex_unlock(slock); + + return ret; } static int adis16136_get_filter(struct iio_dev *indio_dev, int *val) { struct adis16136 *adis16136 = iio_priv(indio_dev); + struct mutex *slock = &adis16136->adis.state_lock; unsigned int freq; uint16_t val16; int ret; - mutex_lock(&indio_dev->mlock); + mutex_lock(slock); - ret = adis_read_reg_16(&adis16136->adis, ADIS16136_REG_AVG_CNT, &val16); + ret = __adis_read_reg_16(&adis16136->adis, ADIS16136_REG_AVG_CNT, + &val16); if (ret) goto err_unlock; - ret = adis16136_get_freq(adis16136, &freq); + ret = __adis16136_get_freq(adis16136, &freq); if (ret) goto err_unlock; *val = freq / adis16136_3db_divisors[val16 & 0x07]; err_unlock: - mutex_unlock(&indio_dev->mlock); + mutex_unlock(slock); return ret ? ret : IIO_VAL_INT; } @@ -460,7 +472,6 @@ static const struct adis_data adis16136_data = { .msc_ctrl_reg = ADIS16136_REG_MSC_CTRL, .self_test_mask = ADIS16136_MSC_CTRL_SELF_TEST, - .startup_delay = 80, .read_delay = 10, .write_delay = 10, @@ -479,30 +490,63 @@ enum adis16136_id { ID_ADIS16137, }; +static const struct adis_timeout adis16133_timeouts = { + .reset_ms = 75, + .sw_reset_ms = 75, + .self_test_ms = 50, +}; + +static const struct adis_timeout adis16136_timeouts = { + .reset_ms = 128, + .sw_reset_ms = 75, + .self_test_ms = 245, +}; + static const struct adis16136_chip_info adis16136_chip_info[] = { [ID_ADIS16133] = { .precision = IIO_DEGREE_TO_RAD(1200), .fullscale = 24000, + .timeouts = &adis16133_timeouts, }, [ID_ADIS16135] = { .precision = IIO_DEGREE_TO_RAD(300), .fullscale = 24000, + .timeouts = &adis16133_timeouts, }, [ID_ADIS16136] = { .precision = IIO_DEGREE_TO_RAD(450), .fullscale = 24623, + .timeouts = &adis16136_timeouts, }, [ID_ADIS16137] = { .precision = IIO_DEGREE_TO_RAD(1000), .fullscale = 24609, + .timeouts = &adis16136_timeouts, }, }; +static struct adis_data *adis16136_adis_data_alloc(struct adis16136 *st, + struct device *dev) +{ + struct adis_data *data; + + data = devm_kmalloc(dev, sizeof(struct adis_data), GFP_KERNEL); + if (!data) + return ERR_PTR(-ENOMEM); + + memcpy(data, &adis16136_data, sizeof(*data)); + + data->timeouts = st->chip_info->timeouts; + + return data; +} + static int adis16136_probe(struct spi_device *spi) { const struct spi_device_id *id = spi_get_device_id(spi); struct adis16136 *adis16136; struct iio_dev *indio_dev; + const struct adis_data *adis16136_data; int ret; indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*adis16136)); @@ -521,7 +565,11 @@ static int adis16136_probe(struct spi_device *spi) indio_dev->info = &adis16136_info; indio_dev->modes = INDIO_DIRECT_MODE; - ret = adis_init(&adis16136->adis, indio_dev, spi, &adis16136_data); + adis16136_data = adis16136_adis_data_alloc(adis16136, &spi->dev); + if (IS_ERR(adis16136_data)) + return PTR_ERR(adis16136_data); + + ret = adis_init(&adis16136->adis, indio_dev, spi, adis16136_data); if (ret) return ret; diff --git a/drivers/iio/gyro/adis16260.c b/drivers/iio/gyro/adis16260.c index 207a0ce13439..be09b3e5910c 100644 --- a/drivers/iio/gyro/adis16260.c +++ b/drivers/iio/gyro/adis16260.c @@ -293,7 +293,7 @@ static int adis16260_write_raw(struct iio_dev *indio_dev, addr = adis16260_addresses[chan->scan_index][1]; return adis_write_reg_16(adis, addr, val); case IIO_CHAN_INFO_SAMP_FREQ: - mutex_lock(&indio_dev->mlock); + mutex_lock(&adis->state_lock); if (spi_get_device_id(adis->spi)->driver_data) t = 256 / val; else @@ -308,9 +308,9 @@ static int adis16260_write_raw(struct iio_dev *indio_dev, adis->spi->max_speed_hz = ADIS16260_SPI_SLOW; else adis->spi->max_speed_hz = ADIS16260_SPI_FAST; - ret = adis_write_reg_8(adis, ADIS16260_SMPL_PRD, t); + ret = __adis_write_reg_8(adis, ADIS16260_SMPL_PRD, t); - mutex_unlock(&indio_dev->mlock); + mutex_unlock(&adis->state_lock); return ret; } return -EINVAL; @@ -332,6 +332,12 @@ static const char * const adis1620_status_error_msgs[] = { [ADIS16260_DIAG_STAT_POWER_LOW_BIT] = "Power supply below 4.75", }; +static const struct adis_timeout adis16260_timeouts = { + .reset_ms = ADIS16260_STARTUP_DELAY, + .sw_reset_ms = ADIS16260_STARTUP_DELAY, + .self_test_ms = ADIS16260_STARTUP_DELAY, +}; + static const struct adis_data adis16260_data = { .write_delay = 30, .read_delay = 30, @@ -340,7 +346,7 @@ static const struct adis_data adis16260_data = { .diag_stat_reg = ADIS16260_DIAG_STAT, .self_test_mask = ADIS16260_MSC_CTRL_MEM_TEST, - .startup_delay = ADIS16260_STARTUP_DELAY, + .timeouts = &adis16260_timeouts, .status_error_msgs = adis1620_status_error_msgs, .status_error_mask = BIT(ADIS16260_DIAG_STAT_FLASH_CHK_BIT) | diff --git a/drivers/iio/gyro/itg3200_core.c b/drivers/iio/gyro/itg3200_core.c index 981ae2291505..b3afa556f973 100644 --- a/drivers/iio/gyro/itg3200_core.c +++ b/drivers/iio/gyro/itg3200_core.c @@ -15,7 +15,6 @@ #include <linux/interrupt.h> #include <linux/irq.h> #include <linux/i2c.h> -#include <linux/gpio.h> #include <linux/slab.h> #include <linux/stat.h> #include <linux/module.h> diff --git a/drivers/iio/gyro/st_gyro.h b/drivers/iio/gyro/st_gyro.h index 592f6b34e987..fd9171cc3aba 100644 --- a/drivers/iio/gyro/st_gyro.h +++ b/drivers/iio/gyro/st_gyro.h @@ -28,7 +28,7 @@ * struct st_sensors_platform_data - gyro platform data * @drdy_int_pin: DRDY on gyros is available only on INT2 pin. */ -static const struct st_sensors_platform_data gyro_pdata = { +static __maybe_unused const struct st_sensors_platform_data gyro_pdata = { .drdy_int_pin = 2, }; diff --git a/drivers/iio/gyro/st_gyro_core.c b/drivers/iio/gyro/st_gyro_core.c index 57be68b291fa..26c50b24bc08 100644 --- a/drivers/iio/gyro/st_gyro_core.c +++ b/drivers/iio/gyro/st_gyro_core.c @@ -138,7 +138,6 @@ static const struct st_sensor_settings st_gyro_sensors_settings[] = { [2] = LSM330DLC_GYRO_DEV_NAME, [3] = L3G4IS_GYRO_DEV_NAME, [4] = LSM330_GYRO_DEV_NAME, - [5] = LSM9DS0_GYRO_DEV_NAME, }, .ch = (struct iio_chan_spec *)st_gyro_16bit_channels, .odr = { @@ -209,6 +208,80 @@ static const struct st_sensor_settings st_gyro_sensors_settings[] = { .bootime = 2, }, { + .wai = 0xd4, + .wai_addr = ST_SENSORS_DEFAULT_WAI_ADDRESS, + .sensors_supported = { + [0] = LSM9DS0_GYRO_DEV_NAME, + }, + .ch = (struct iio_chan_spec *)st_gyro_16bit_channels, + .odr = { + .addr = 0x20, + .mask = GENMASK(7, 6), + .odr_avl = { + { .hz = 95, .value = 0x00, }, + { .hz = 190, .value = 0x01, }, + { .hz = 380, .value = 0x02, }, + { .hz = 760, .value = 0x03, }, + }, + }, + .pw = { + .addr = 0x20, + .mask = BIT(3), + .value_on = ST_SENSORS_DEFAULT_POWER_ON_VALUE, + .value_off = ST_SENSORS_DEFAULT_POWER_OFF_VALUE, + }, + .enable_axis = { + .addr = ST_SENSORS_DEFAULT_AXIS_ADDR, + .mask = ST_SENSORS_DEFAULT_AXIS_MASK, + }, + .fs = { + .addr = 0x23, + .mask = GENMASK(5, 4), + .fs_avl = { + [0] = { + .num = ST_GYRO_FS_AVL_245DPS, + .value = 0x00, + .gain = IIO_DEGREE_TO_RAD(8750), + }, + [1] = { + .num = ST_GYRO_FS_AVL_500DPS, + .value = 0x01, + .gain = IIO_DEGREE_TO_RAD(17500), + }, + [2] = { + .num = ST_GYRO_FS_AVL_2000DPS, + .value = 0x02, + .gain = IIO_DEGREE_TO_RAD(70000), + }, + }, + }, + .bdu = { + .addr = 0x23, + .mask = BIT(7), + }, + .drdy_irq = { + .int2 = { + .addr = 0x22, + .mask = BIT(3), + }, + /* + * The sensor has IHL (active low) and open + * drain settings, but only for INT1 and not + * for the DRDY line on INT2. + */ + .stat_drdy = { + .addr = ST_SENSORS_DEFAULT_STAT_ADDR, + .mask = GENMASK(2, 0), + }, + }, + .sim = { + .addr = 0x23, + .value = BIT(0), + }, + .multi_read_bit = true, + .bootime = 2, + }, + { .wai = 0xd7, .wai_addr = ST_SENSORS_DEFAULT_WAI_ADDRESS, .sensors_supported = { diff --git a/drivers/iio/gyro/st_gyro_i2c.c b/drivers/iio/gyro/st_gyro_i2c.c index 05a1a0874bd5..8190966e6ff0 100644 --- a/drivers/iio/gyro/st_gyro_i2c.c +++ b/drivers/iio/gyro/st_gyro_i2c.c @@ -17,7 +17,6 @@ #include <linux/iio/common/st_sensors_i2c.h> #include "st_gyro.h" -#ifdef CONFIG_OF static const struct of_device_id st_gyro_of_match[] = { { .compatible = "st,l3g4200d-gyro", @@ -58,9 +57,6 @@ static const struct of_device_id st_gyro_of_match[] = { {}, }; MODULE_DEVICE_TABLE(of, st_gyro_of_match); -#else -#define st_gyro_of_match NULL -#endif static int st_gyro_i2c_probe(struct i2c_client *client, const struct i2c_device_id *id) @@ -70,8 +66,7 @@ static int st_gyro_i2c_probe(struct i2c_client *client, struct iio_dev *indio_dev; int err; - st_sensors_of_name_probe(&client->dev, st_gyro_of_match, - client->name, sizeof(client->name)); + st_sensors_dev_name_probe(&client->dev, client->name, sizeof(client->name)); settings = st_gyro_get_settings(client->name); if (!settings) { @@ -122,7 +117,7 @@ MODULE_DEVICE_TABLE(i2c, st_gyro_id_table); static struct i2c_driver st_gyro_driver = { .driver = { .name = "st-gyro-i2c", - .of_match_table = of_match_ptr(st_gyro_of_match), + .of_match_table = st_gyro_of_match, }, .probe = st_gyro_i2c_probe, .remove = st_gyro_i2c_remove, diff --git a/drivers/iio/gyro/st_gyro_spi.c b/drivers/iio/gyro/st_gyro_spi.c index b5c624251231..efb862763ca3 100644 --- a/drivers/iio/gyro/st_gyro_spi.c +++ b/drivers/iio/gyro/st_gyro_spi.c @@ -17,7 +17,6 @@ #include <linux/iio/common/st_sensors_spi.h> #include "st_gyro.h" -#ifdef CONFIG_OF /* * For new single-chip sensors use <device_name> as compatible string. * For old single-chip devices keep <device_name>-gyro to maintain @@ -63,9 +62,6 @@ static const struct of_device_id st_gyro_of_match[] = { {}, }; MODULE_DEVICE_TABLE(of, st_gyro_of_match); -#else -#define st_gyro_of_match NULL -#endif static int st_gyro_spi_probe(struct spi_device *spi) { @@ -74,8 +70,7 @@ static int st_gyro_spi_probe(struct spi_device *spi) struct iio_dev *indio_dev; int err; - st_sensors_of_name_probe(&spi->dev, st_gyro_of_match, - spi->modalias, sizeof(spi->modalias)); + st_sensors_dev_name_probe(&spi->dev, spi->modalias, sizeof(spi->modalias)); settings = st_gyro_get_settings(spi->modalias); if (!settings) { @@ -126,7 +121,7 @@ MODULE_DEVICE_TABLE(spi, st_gyro_id_table); static struct spi_driver st_gyro_driver = { .driver = { .name = "st-gyro-spi", - .of_match_table = of_match_ptr(st_gyro_of_match), + .of_match_table = st_gyro_of_match, }, .probe = st_gyro_spi_probe, .remove = st_gyro_spi_remove, diff --git a/drivers/iio/humidity/dht11.c b/drivers/iio/humidity/dht11.c index b459600e1a33..d05c6fdb758b 100644 --- a/drivers/iio/humidity/dht11.c +++ b/drivers/iio/humidity/dht11.c @@ -174,7 +174,6 @@ static irqreturn_t dht11_handle_irq(int irq, void *data) struct iio_dev *iio = data; struct dht11 *dht11 = iio_priv(iio); - /* TODO: Consider making the handler safe for IRQ sharing */ if (dht11->num_edges < DHT11_EDGES_PER_READ && dht11->num_edges >= 0) { dht11->edges[dht11->num_edges].ts = ktime_get_boottime_ns(); dht11->edges[dht11->num_edges++].value = diff --git a/drivers/iio/humidity/hts221_core.c b/drivers/iio/humidity/hts221_core.c index 4922444771c6..9003671f14fb 100644 --- a/drivers/iio/humidity/hts221_core.c +++ b/drivers/iio/humidity/hts221_core.c @@ -24,13 +24,6 @@ #define HTS221_REG_CNTRL1_ADDR 0x20 #define HTS221_REG_CNTRL2_ADDR 0x21 -#define HTS221_REG_AVG_ADDR 0x10 -#define HTS221_REG_H_OUT_L 0x28 -#define HTS221_REG_T_OUT_L 0x2a - -#define HTS221_HUMIDITY_AVG_MASK 0x07 -#define HTS221_TEMP_AVG_MASK 0x38 - #define HTS221_ODR_MASK 0x03 #define HTS221_BDU_MASK BIT(2) #define HTS221_ENABLE_MASK BIT(7) @@ -66,8 +59,8 @@ static const struct hts221_odr hts221_odr_table[] = { static const struct hts221_avg hts221_avg_list[] = { { - .addr = HTS221_REG_AVG_ADDR, - .mask = HTS221_HUMIDITY_AVG_MASK, + .addr = 0x10, + .mask = 0x07, .avg_avl = { 4, /* 0.4 %RH */ 8, /* 0.3 %RH */ @@ -80,8 +73,8 @@ static const struct hts221_avg hts221_avg_list[] = { }, }, { - .addr = HTS221_REG_AVG_ADDR, - .mask = HTS221_TEMP_AVG_MASK, + .addr = 0x10, + .mask = 0x38, .avg_avl = { 2, /* 0.08 degC */ 4, /* 0.05 degC */ @@ -98,7 +91,7 @@ static const struct hts221_avg hts221_avg_list[] = { static const struct iio_chan_spec hts221_channels[] = { { .type = IIO_HUMIDITYRELATIVE, - .address = HTS221_REG_H_OUT_L, + .address = 0x28, .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_OFFSET) | BIT(IIO_CHAN_INFO_SCALE) | @@ -114,7 +107,7 @@ static const struct iio_chan_spec hts221_channels[] = { }, { .type = IIO_TEMP, - .address = HTS221_REG_T_OUT_L, + .address = 0x2a, .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_OFFSET) | BIT(IIO_CHAN_INFO_SCALE) | diff --git a/drivers/iio/iio_core.h b/drivers/iio/iio_core.h index 159ea3f8c02b..fd9a5f1d5e51 100644 --- a/drivers/iio/iio_core.h +++ b/drivers/iio/iio_core.h @@ -42,14 +42,14 @@ struct poll_table_struct; __poll_t iio_buffer_poll(struct file *filp, struct poll_table_struct *wait); -ssize_t iio_buffer_read_first_n_outer(struct file *filp, char __user *buf, - size_t n, loff_t *f_ps); +ssize_t iio_buffer_read_outer(struct file *filp, char __user *buf, + size_t n, loff_t *f_ps); int iio_buffer_alloc_sysfs_and_mask(struct iio_dev *indio_dev); void iio_buffer_free_sysfs_and_mask(struct iio_dev *indio_dev); #define iio_buffer_poll_addr (&iio_buffer_poll) -#define iio_buffer_read_first_n_outer_addr (&iio_buffer_read_first_n_outer) +#define iio_buffer_read_outer_addr (&iio_buffer_read_outer) void iio_disable_all_buffers(struct iio_dev *indio_dev); void iio_buffer_wakeup_poll(struct iio_dev *indio_dev); @@ -57,7 +57,7 @@ void iio_buffer_wakeup_poll(struct iio_dev *indio_dev); #else #define iio_buffer_poll_addr NULL -#define iio_buffer_read_first_n_outer_addr NULL +#define iio_buffer_read_outer_addr NULL static inline int iio_buffer_alloc_sysfs_and_mask(struct iio_dev *indio_dev) { diff --git a/drivers/iio/imu/adis.c b/drivers/iio/imu/adis.c index e14c8536fd09..022bb54fb748 100644 --- a/drivers/iio/imu/adis.c +++ b/drivers/iio/imu/adis.c @@ -26,7 +26,14 @@ #define ADIS_MSC_CTRL_DATA_RDY_DIO2 BIT(0) #define ADIS_GLOB_CMD_SW_RESET BIT(7) -int adis_write_reg(struct adis *adis, unsigned int reg, +/** + * __adis_write_reg() - write N bytes to register (unlocked version) + * @adis: The adis device + * @reg: The address of the lower of the two registers + * @value: The value to write to device (up to 4 bytes) + * @size: The size of the @value (in bytes) + */ +int __adis_write_reg(struct adis *adis, unsigned int reg, unsigned int value, unsigned int size) { unsigned int page = reg / ADIS_PAGE_SIZE; @@ -38,7 +45,8 @@ int adis_write_reg(struct adis *adis, unsigned int reg, .bits_per_word = 8, .len = 2, .cs_change = 1, - .delay_usecs = adis->data->write_delay, + .delay.value = adis->data->write_delay, + .delay.unit = SPI_DELAY_UNIT_USECS, .cs_change_delay.value = adis->data->cs_change_delay, .cs_change_delay.unit = SPI_DELAY_UNIT_USECS, }, { @@ -46,7 +54,8 @@ int adis_write_reg(struct adis *adis, unsigned int reg, .bits_per_word = 8, .len = 2, .cs_change = 1, - .delay_usecs = adis->data->write_delay, + .delay.value = adis->data->write_delay, + .delay.unit = SPI_DELAY_UNIT_USECS, .cs_change_delay.value = adis->data->cs_change_delay, .cs_change_delay.unit = SPI_DELAY_UNIT_USECS, }, { @@ -54,24 +63,25 @@ int adis_write_reg(struct adis *adis, unsigned int reg, .bits_per_word = 8, .len = 2, .cs_change = 1, - .delay_usecs = adis->data->write_delay, + .delay.value = adis->data->write_delay, + .delay.unit = SPI_DELAY_UNIT_USECS, .cs_change_delay.value = adis->data->cs_change_delay, .cs_change_delay.unit = SPI_DELAY_UNIT_USECS, }, { .tx_buf = adis->tx + 6, .bits_per_word = 8, .len = 2, - .delay_usecs = adis->data->write_delay, + .delay.value = adis->data->write_delay, + .delay.unit = SPI_DELAY_UNIT_USECS, }, { .tx_buf = adis->tx + 8, .bits_per_word = 8, .len = 2, - .delay_usecs = adis->data->write_delay, + .delay.value = adis->data->write_delay, + .delay.unit = SPI_DELAY_UNIT_USECS, }, }; - mutex_lock(&adis->txrx_lock); - spi_message_init(&msg); if (adis->current_page != page) { @@ -96,8 +106,7 @@ int adis_write_reg(struct adis *adis, unsigned int reg, adis->tx[3] = value & 0xff; break; default: - ret = -EINVAL; - goto out_unlock; + return -EINVAL; } xfers[size].cs_change = 0; @@ -113,20 +122,18 @@ int adis_write_reg(struct adis *adis, unsigned int reg, adis->current_page = page; } -out_unlock: - mutex_unlock(&adis->txrx_lock); - return ret; } -EXPORT_SYMBOL_GPL(adis_write_reg); +EXPORT_SYMBOL_GPL(__adis_write_reg); /** - * adis_read_reg() - read 2 bytes from a 16-bit register + * __adis_read_reg() - read N bytes from register (unlocked version) * @adis: The adis device * @reg: The address of the lower of the two registers * @val: The value read back from the device + * @size: The size of the @val buffer */ -int adis_read_reg(struct adis *adis, unsigned int reg, +int __adis_read_reg(struct adis *adis, unsigned int reg, unsigned int *val, unsigned int size) { unsigned int page = reg / ADIS_PAGE_SIZE; @@ -138,7 +145,8 @@ int adis_read_reg(struct adis *adis, unsigned int reg, .bits_per_word = 8, .len = 2, .cs_change = 1, - .delay_usecs = adis->data->write_delay, + .delay.value = adis->data->write_delay, + .delay.unit = SPI_DELAY_UNIT_USECS, .cs_change_delay.value = adis->data->cs_change_delay, .cs_change_delay.unit = SPI_DELAY_UNIT_USECS, }, { @@ -146,7 +154,8 @@ int adis_read_reg(struct adis *adis, unsigned int reg, .bits_per_word = 8, .len = 2, .cs_change = 1, - .delay_usecs = adis->data->read_delay, + .delay.value = adis->data->read_delay, + .delay.unit = SPI_DELAY_UNIT_USECS, .cs_change_delay.value = adis->data->cs_change_delay, .cs_change_delay.unit = SPI_DELAY_UNIT_USECS, }, { @@ -155,18 +164,19 @@ int adis_read_reg(struct adis *adis, unsigned int reg, .bits_per_word = 8, .len = 2, .cs_change = 1, - .delay_usecs = adis->data->read_delay, + .delay.value = adis->data->read_delay, + .delay.unit = SPI_DELAY_UNIT_USECS, .cs_change_delay.value = adis->data->cs_change_delay, .cs_change_delay.unit = SPI_DELAY_UNIT_USECS, }, { .rx_buf = adis->rx + 2, .bits_per_word = 8, .len = 2, - .delay_usecs = adis->data->read_delay, + .delay.value = adis->data->read_delay, + .delay.unit = SPI_DELAY_UNIT_USECS, }, }; - mutex_lock(&adis->txrx_lock); spi_message_init(&msg); if (adis->current_page != page) { @@ -188,15 +198,14 @@ int adis_read_reg(struct adis *adis, unsigned int reg, spi_message_add_tail(&xfers[3], &msg); break; default: - ret = -EINVAL; - goto out_unlock; + return -EINVAL; } ret = spi_sync(adis->spi, &msg); if (ret) { dev_err(&adis->spi->dev, "Failed to read register 0x%02X: %d\n", reg, ret); - goto out_unlock; + return ret; } else { adis->current_page = page; } @@ -210,12 +219,9 @@ int adis_read_reg(struct adis *adis, unsigned int reg, break; } -out_unlock: - mutex_unlock(&adis->txrx_lock); - return ret; } -EXPORT_SYMBOL_GPL(adis_read_reg); +EXPORT_SYMBOL_GPL(__adis_read_reg); #ifdef CONFIG_DEBUG_FS @@ -253,12 +259,16 @@ int adis_enable_irq(struct adis *adis, bool enable) int ret = 0; uint16_t msc; - if (adis->data->enable_irq) - return adis->data->enable_irq(adis, enable); + mutex_lock(&adis->state_lock); + + if (adis->data->enable_irq) { + ret = adis->data->enable_irq(adis, enable); + goto out_unlock; + } - ret = adis_read_reg_16(adis, adis->data->msc_ctrl_reg, &msc); + ret = __adis_read_reg_16(adis, adis->data->msc_ctrl_reg, &msc); if (ret) - goto error_ret; + goto out_unlock; msc |= ADIS_MSC_CTRL_DATA_RDY_POL_HIGH; msc &= ~ADIS_MSC_CTRL_DATA_RDY_DIO2; @@ -267,26 +277,27 @@ int adis_enable_irq(struct adis *adis, bool enable) else msc &= ~ADIS_MSC_CTRL_DATA_RDY_EN; - ret = adis_write_reg_16(adis, adis->data->msc_ctrl_reg, msc); + ret = __adis_write_reg_16(adis, adis->data->msc_ctrl_reg, msc); -error_ret: +out_unlock: + mutex_unlock(&adis->state_lock); return ret; } EXPORT_SYMBOL(adis_enable_irq); /** - * adis_check_status() - Check the device for error conditions + * __adis_check_status() - Check the device for error conditions (unlocked) * @adis: The adis device * * Returns 0 on success, a negative error code otherwise */ -int adis_check_status(struct adis *adis) +int __adis_check_status(struct adis *adis) { uint16_t status; int ret; int i; - ret = adis_read_reg_16(adis, adis->data->diag_stat_reg, &status); + ret = __adis_read_reg_16(adis, adis->data->diag_stat_reg, &status); if (ret) return ret; @@ -304,32 +315,38 @@ int adis_check_status(struct adis *adis) return -EIO; } -EXPORT_SYMBOL_GPL(adis_check_status); +EXPORT_SYMBOL_GPL(__adis_check_status); /** - * adis_reset() - Reset the device + * __adis_reset() - Reset the device (unlocked version) * @adis: The adis device * * Returns 0 on success, a negative error code otherwise */ -int adis_reset(struct adis *adis) +int __adis_reset(struct adis *adis) { int ret; + const struct adis_timeout *timeouts = adis->data->timeouts; - ret = adis_write_reg_8(adis, adis->data->glob_cmd_reg, + ret = __adis_write_reg_8(adis, adis->data->glob_cmd_reg, ADIS_GLOB_CMD_SW_RESET); - if (ret) + if (ret) { dev_err(&adis->spi->dev, "Failed to reset device: %d\n", ret); + return ret; + } - return ret; + msleep(timeouts->sw_reset_ms); + + return 0; } -EXPORT_SYMBOL_GPL(adis_reset); +EXPORT_SYMBOL_GPL(__adis_reset); static int adis_self_test(struct adis *adis) { int ret; + const struct adis_timeout *timeouts = adis->data->timeouts; - ret = adis_write_reg_16(adis, adis->data->msc_ctrl_reg, + ret = __adis_write_reg_16(adis, adis->data->msc_ctrl_reg, adis->data->self_test_mask); if (ret) { dev_err(&adis->spi->dev, "Failed to initiate self test: %d\n", @@ -337,12 +354,12 @@ static int adis_self_test(struct adis *adis) return ret; } - msleep(adis->data->startup_delay); + msleep(timeouts->self_test_ms); - ret = adis_check_status(adis); + ret = __adis_check_status(adis); if (adis->data->self_test_no_autoclear) - adis_write_reg_16(adis, adis->data->msc_ctrl_reg, 0x00); + __adis_write_reg_16(adis, adis->data->msc_ctrl_reg, 0x00); return ret; } @@ -360,19 +377,22 @@ int adis_initial_startup(struct adis *adis) { int ret; + mutex_lock(&adis->state_lock); + ret = adis_self_test(adis); if (ret) { dev_err(&adis->spi->dev, "Self-test failed, trying reset.\n"); - adis_reset(adis); - msleep(adis->data->startup_delay); + __adis_reset(adis); ret = adis_self_test(adis); if (ret) { dev_err(&adis->spi->dev, "Second self-test failed, giving up.\n"); - return ret; + goto out_unlock; } } - return 0; +out_unlock: + mutex_unlock(&adis->state_lock); + return ret; } EXPORT_SYMBOL_GPL(adis_initial_startup); @@ -398,15 +418,15 @@ int adis_single_conversion(struct iio_dev *indio_dev, unsigned int uval; int ret; - mutex_lock(&indio_dev->mlock); + mutex_lock(&adis->state_lock); - ret = adis_read_reg(adis, chan->address, &uval, + ret = __adis_read_reg(adis, chan->address, &uval, chan->scan_type.storagebits / 8); if (ret) goto err_unlock; if (uval & error_mask) { - ret = adis_check_status(adis); + ret = __adis_check_status(adis); if (ret) goto err_unlock; } @@ -418,7 +438,7 @@ int adis_single_conversion(struct iio_dev *indio_dev, ret = IIO_VAL_INT; err_unlock: - mutex_unlock(&indio_dev->mlock); + mutex_unlock(&adis->state_lock); return ret; } EXPORT_SYMBOL_GPL(adis_single_conversion); @@ -438,7 +458,12 @@ EXPORT_SYMBOL_GPL(adis_single_conversion); int adis_init(struct adis *adis, struct iio_dev *indio_dev, struct spi_device *spi, const struct adis_data *data) { - mutex_init(&adis->txrx_lock); + if (!data || !data->timeouts) { + dev_err(&spi->dev, "No config data or timeouts not defined!\n"); + return -EINVAL; + } + + mutex_init(&adis->state_lock); adis->spi = spi; adis->data = data; iio_device_set_drvdata(indio_dev, adis); diff --git a/drivers/iio/imu/adis16400.c b/drivers/iio/imu/adis16400.c index 44e46dc96e00..cfb1c19eb930 100644 --- a/drivers/iio/imu/adis16400.c +++ b/drivers/iio/imu/adis16400.c @@ -156,12 +156,14 @@ struct adis16400_state; struct adis16400_chip_info { const struct iio_chan_spec *channels; + const struct adis_timeout *timeouts; const int num_channels; const long flags; unsigned int gyro_scale_micro; unsigned int accel_scale_micro; int temp_scale_nano; int temp_offset; + /* set_freq() & get_freq() need to avoid using ADIS lib's state lock */ int (*set_freq)(struct adis16400_state *st, unsigned int freq); int (*get_freq)(struct adis16400_state *st); }; @@ -326,7 +328,7 @@ static int adis16334_get_freq(struct adis16400_state *st) int ret; uint16_t t; - ret = adis_read_reg_16(&st->adis, ADIS16400_SMPL_PRD, &t); + ret = __adis_read_reg_16(&st->adis, ADIS16400_SMPL_PRD, &t); if (ret) return ret; @@ -350,7 +352,7 @@ static int adis16334_set_freq(struct adis16400_state *st, unsigned int freq) t <<= ADIS16334_RATE_DIV_SHIFT; t |= ADIS16334_RATE_INT_CLK; - return adis_write_reg_16(&st->adis, ADIS16400_SMPL_PRD, t); + return __adis_write_reg_16(&st->adis, ADIS16400_SMPL_PRD, t); } static int adis16400_get_freq(struct adis16400_state *st) @@ -358,7 +360,7 @@ static int adis16400_get_freq(struct adis16400_state *st) int sps, ret; uint16_t t; - ret = adis_read_reg_16(&st->adis, ADIS16400_SMPL_PRD, &t); + ret = __adis_read_reg_16(&st->adis, ADIS16400_SMPL_PRD, &t); if (ret) return ret; @@ -390,7 +392,7 @@ static int adis16400_set_freq(struct adis16400_state *st, unsigned int freq) else st->adis.spi->max_speed_hz = ADIS16400_SPI_FAST; - return adis_write_reg_8(&st->adis, ADIS16400_SMPL_PRD, val); + return __adis_write_reg_8(&st->adis, ADIS16400_SMPL_PRD, val); } static const unsigned int adis16400_3db_divisors[] = { @@ -404,7 +406,7 @@ static const unsigned int adis16400_3db_divisors[] = { [7] = 200, /* Not a valid setting */ }; -static int adis16400_set_filter(struct iio_dev *indio_dev, int sps, int val) +static int __adis16400_set_filter(struct iio_dev *indio_dev, int sps, int val) { struct adis16400_state *st = iio_priv(indio_dev); uint16_t val16; @@ -415,11 +417,11 @@ static int adis16400_set_filter(struct iio_dev *indio_dev, int sps, int val) break; } - ret = adis_read_reg_16(&st->adis, ADIS16400_SENS_AVG, &val16); + ret = __adis_read_reg_16(&st->adis, ADIS16400_SENS_AVG, &val16); if (ret) return ret; - ret = adis_write_reg_16(&st->adis, ADIS16400_SENS_AVG, + ret = __adis_write_reg_16(&st->adis, ADIS16400_SENS_AVG, (val16 & ~0x07) | i); return ret; } @@ -507,32 +509,31 @@ static int adis16400_write_raw(struct iio_dev *indio_dev, struct iio_chan_spec const *chan, int val, int val2, long info) { struct adis16400_state *st = iio_priv(indio_dev); + struct mutex *slock = &st->adis.state_lock; int ret, sps; switch (info) { case IIO_CHAN_INFO_CALIBBIAS: - mutex_lock(&indio_dev->mlock); ret = adis_write_reg_16(&st->adis, adis16400_addresses[chan->scan_index], val); - mutex_unlock(&indio_dev->mlock); return ret; case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY: /* * Need to cache values so we can update if the frequency * changes. */ - mutex_lock(&indio_dev->mlock); + mutex_lock(slock); st->filt_int = val; /* Work out update to current value */ sps = st->variant->get_freq(st); if (sps < 0) { - mutex_unlock(&indio_dev->mlock); + mutex_unlock(slock); return sps; } - ret = adis16400_set_filter(indio_dev, sps, + ret = __adis16400_set_filter(indio_dev, sps, val * 1000 + val2 / 1000); - mutex_unlock(&indio_dev->mlock); + mutex_unlock(slock); return ret; case IIO_CHAN_INFO_SAMP_FREQ: sps = val * 1000 + val2 / 1000; @@ -540,9 +541,9 @@ static int adis16400_write_raw(struct iio_dev *indio_dev, if (sps <= 0) return -EINVAL; - mutex_lock(&indio_dev->mlock); + mutex_lock(slock); ret = st->variant->set_freq(st, sps); - mutex_unlock(&indio_dev->mlock); + mutex_unlock(slock); return ret; default: return -EINVAL; @@ -553,6 +554,7 @@ static int adis16400_read_raw(struct iio_dev *indio_dev, struct iio_chan_spec const *chan, int *val, int *val2, long info) { struct adis16400_state *st = iio_priv(indio_dev); + struct mutex *slock = &st->adis.state_lock; int16_t val16; int ret; @@ -596,10 +598,8 @@ static int adis16400_read_raw(struct iio_dev *indio_dev, return -EINVAL; } case IIO_CHAN_INFO_CALIBBIAS: - mutex_lock(&indio_dev->mlock); ret = adis_read_reg_16(&st->adis, adis16400_addresses[chan->scan_index], &val16); - mutex_unlock(&indio_dev->mlock); if (ret) return ret; val16 = sign_extend32(val16, 11); @@ -610,27 +610,27 @@ static int adis16400_read_raw(struct iio_dev *indio_dev, *val = st->variant->temp_offset; return IIO_VAL_INT; case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY: - mutex_lock(&indio_dev->mlock); + mutex_lock(slock); /* Need both the number of taps and the sampling frequency */ - ret = adis_read_reg_16(&st->adis, + ret = __adis_read_reg_16(&st->adis, ADIS16400_SENS_AVG, &val16); if (ret) { - mutex_unlock(&indio_dev->mlock); + mutex_unlock(slock); return ret; } ret = st->variant->get_freq(st); - if (ret >= 0) { - ret /= adis16400_3db_divisors[val16 & 0x07]; - *val = ret / 1000; - *val2 = (ret % 1000) * 1000; - } - mutex_unlock(&indio_dev->mlock); + mutex_unlock(slock); if (ret) return ret; + ret /= adis16400_3db_divisors[val16 & 0x07]; + *val = ret / 1000; + *val2 = (ret % 1000) * 1000; return IIO_VAL_INT_PLUS_MICRO; case IIO_CHAN_INFO_SAMP_FREQ: + mutex_lock(slock); ret = st->variant->get_freq(st); + mutex_unlock(slock); if (ret) return ret; *val = ret / 1000; @@ -930,6 +930,36 @@ static const struct iio_chan_spec adis16334_channels[] = { IIO_CHAN_SOFT_TIMESTAMP(ADIS16400_SCAN_TIMESTAMP), }; +static const struct adis_timeout adis16300_timeouts = { + .reset_ms = ADIS16400_STARTUP_DELAY, + .sw_reset_ms = ADIS16400_STARTUP_DELAY, + .self_test_ms = ADIS16400_STARTUP_DELAY, +}; + +static const struct adis_timeout adis16362_timeouts = { + .reset_ms = 130, + .sw_reset_ms = 130, + .self_test_ms = 12, +}; + +static const struct adis_timeout adis16400_timeouts = { + .reset_ms = 170, + .sw_reset_ms = 170, + .self_test_ms = 12, +}; + +static const struct adis_timeout adis16445_timeouts = { + .reset_ms = 55, + .sw_reset_ms = 55, + .self_test_ms = 16, +}; + +static const struct adis_timeout adis16448_timeouts = { + .reset_ms = 90, + .sw_reset_ms = 90, + .self_test_ms = 45, +}; + static struct adis16400_chip_info adis16400_chips[] = { [ADIS16300] = { .channels = adis16300_channels, @@ -942,6 +972,7 @@ static struct adis16400_chip_info adis16400_chips[] = { .temp_offset = 25000000 / 140000, /* 25 C = 0x00 */ .set_freq = adis16400_set_freq, .get_freq = adis16400_get_freq, + .timeouts = &adis16300_timeouts, }, [ADIS16334] = { .channels = adis16334_channels, @@ -965,6 +996,7 @@ static struct adis16400_chip_info adis16400_chips[] = { .flags = ADIS16400_NO_BURST | ADIS16400_HAS_SLOW_MODE, .set_freq = adis16400_set_freq, .get_freq = adis16400_get_freq, + .timeouts = &adis16300_timeouts, }, [ADIS16360] = { .channels = adis16350_channels, @@ -977,6 +1009,7 @@ static struct adis16400_chip_info adis16400_chips[] = { .temp_offset = 25000000 / 136000, /* 25 C = 0x00 */ .set_freq = adis16400_set_freq, .get_freq = adis16400_get_freq, + .timeouts = &adis16300_timeouts, }, [ADIS16362] = { .channels = adis16350_channels, @@ -989,6 +1022,7 @@ static struct adis16400_chip_info adis16400_chips[] = { .temp_offset = 25000000 / 136000, /* 25 C = 0x00 */ .set_freq = adis16400_set_freq, .get_freq = adis16400_get_freq, + .timeouts = &adis16362_timeouts, }, [ADIS16364] = { .channels = adis16350_channels, @@ -1001,6 +1035,7 @@ static struct adis16400_chip_info adis16400_chips[] = { .temp_offset = 25000000 / 136000, /* 25 C = 0x00 */ .set_freq = adis16400_set_freq, .get_freq = adis16400_get_freq, + .timeouts = &adis16362_timeouts, }, [ADIS16367] = { .channels = adis16350_channels, @@ -1013,6 +1048,7 @@ static struct adis16400_chip_info adis16400_chips[] = { .temp_offset = 25000000 / 136000, /* 25 C = 0x00 */ .set_freq = adis16400_set_freq, .get_freq = adis16400_get_freq, + .timeouts = &adis16300_timeouts, }, [ADIS16400] = { .channels = adis16400_channels, @@ -1024,6 +1060,7 @@ static struct adis16400_chip_info adis16400_chips[] = { .temp_offset = 25000000 / 140000, /* 25 C = 0x00 */ .set_freq = adis16400_set_freq, .get_freq = adis16400_get_freq, + .timeouts = &adis16400_timeouts, }, [ADIS16445] = { .channels = adis16445_channels, @@ -1037,6 +1074,7 @@ static struct adis16400_chip_info adis16400_chips[] = { .temp_offset = 31000000 / 73860, /* 31 C = 0x00 */ .set_freq = adis16334_set_freq, .get_freq = adis16334_get_freq, + .timeouts = &adis16445_timeouts, }, [ADIS16448] = { .channels = adis16448_channels, @@ -1050,6 +1088,7 @@ static struct adis16400_chip_info adis16400_chips[] = { .temp_offset = 31000000 / 73860, /* 31 C = 0x00 */ .set_freq = adis16334_set_freq, .get_freq = adis16334_get_freq, + .timeouts = &adis16448_timeouts, } }; @@ -1087,7 +1126,6 @@ static const struct adis_data adis16400_data = { .write_delay = 50, .self_test_mask = ADIS16400_MSC_CTRL_MEM_TEST, - .startup_delay = ADIS16400_STARTUP_DELAY, .status_error_msgs = adis16400_status_error_msgs, .status_error_mask = BIT(ADIS16400_DIAG_STAT_ZACCL_FAIL) | @@ -1121,11 +1159,28 @@ static void adis16400_setup_chan_mask(struct adis16400_state *st) } } +static struct adis_data *adis16400_adis_data_alloc(struct adis16400_state *st, + struct device *dev) +{ + struct adis_data *data; + + data = devm_kmalloc(dev, sizeof(struct adis_data), GFP_KERNEL); + if (!data) + return ERR_PTR(-ENOMEM); + + memcpy(data, &adis16400_data, sizeof(*data)); + + data->timeouts = st->variant->timeouts; + + return data; +} + static int adis16400_probe(struct spi_device *spi) { struct adis16400_state *st; struct iio_dev *indio_dev; int ret; + const struct adis_data *adis16400_data; indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st)); if (indio_dev == NULL) @@ -1152,7 +1207,11 @@ static int adis16400_probe(struct spi_device *spi) st->adis.burst->extra_len = sizeof(u16); } - ret = adis_init(&st->adis, indio_dev, spi, &adis16400_data); + adis16400_data = adis16400_adis_data_alloc(st, &spi->dev); + if (IS_ERR(adis16400_data)) + return PTR_ERR(adis16400_data); + + ret = adis_init(&st->adis, indio_dev, spi, adis16400_data); if (ret) return ret; diff --git a/drivers/iio/imu/adis16460.c b/drivers/iio/imu/adis16460.c index b55812521537..9539cfe4a259 100644 --- a/drivers/iio/imu/adis16460.c +++ b/drivers/iio/imu/adis16460.c @@ -383,6 +383,12 @@ static const char * const adis16460_status_error_msgs[] = { [ADIS16460_DIAG_STAT_FLASH_UPT] = "Flash update failure", }; +static const struct adis_timeout adis16460_timeouts = { + .reset_ms = 225, + .sw_reset_ms = 225, + .self_test_ms = 10, +}; + static const struct adis_data adis16460_data = { .diag_stat_reg = ADIS16460_REG_DIAG_STAT, .glob_cmd_reg = ADIS16460_REG_GLOB_CMD, @@ -398,6 +404,7 @@ static const struct adis_data adis16460_data = { BIT(ADIS16460_DIAG_STAT_SPI_COMM) | BIT(ADIS16460_DIAG_STAT_FLASH_UPT), .enable_irq = adis16460_enable_irq, + .timeouts = &adis16460_timeouts, }; static int adis16460_probe(struct spi_device *spi) diff --git a/drivers/iio/imu/adis16480.c b/drivers/iio/imu/adis16480.c index 748f8bbf184d..dac87f1001fd 100644 --- a/drivers/iio/imu/adis16480.c +++ b/drivers/iio/imu/adis16480.c @@ -138,6 +138,7 @@ struct adis16480_chip_info { unsigned int max_dec_rate; const unsigned int *filter_freqs; bool has_pps_clk_mode; + const struct adis_timeout *timeouts; }; enum adis16480_int_pin { @@ -555,6 +556,7 @@ static int adis16480_set_filter_freq(struct iio_dev *indio_dev, const struct iio_chan_spec *chan, unsigned int freq) { struct adis16480 *st = iio_priv(indio_dev); + struct mutex *slock = &st->adis.state_lock; unsigned int enable_mask, offset, reg; unsigned int diff, best_diff; unsigned int i, best_freq; @@ -565,9 +567,11 @@ static int adis16480_set_filter_freq(struct iio_dev *indio_dev, offset = ad16480_filter_data[chan->scan_index][1]; enable_mask = BIT(offset + 2); - ret = adis_read_reg_16(&st->adis, reg, &val); + mutex_lock(slock); + + ret = __adis_read_reg_16(&st->adis, reg, &val); if (ret) - return ret; + goto out_unlock; if (freq == 0) { val &= ~enable_mask; @@ -589,7 +593,11 @@ static int adis16480_set_filter_freq(struct iio_dev *indio_dev, val |= enable_mask; } - return adis_write_reg_16(&st->adis, reg, val); + ret = __adis_write_reg_16(&st->adis, reg, val); +out_unlock: + mutex_unlock(slock); + + return ret; } static int adis16480_read_raw(struct iio_dev *indio_dev, @@ -779,6 +787,7 @@ enum adis16480_variant { ADIS16480, ADIS16485, ADIS16488, + ADIS16490, ADIS16495_1, ADIS16495_2, ADIS16495_3, @@ -787,6 +796,30 @@ enum adis16480_variant { ADIS16497_3, }; +static const struct adis_timeout adis16485_timeouts = { + .reset_ms = 560, + .sw_reset_ms = 120, + .self_test_ms = 12, +}; + +static const struct adis_timeout adis16480_timeouts = { + .reset_ms = 560, + .sw_reset_ms = 560, + .self_test_ms = 12, +}; + +static const struct adis_timeout adis16495_timeouts = { + .reset_ms = 170, + .sw_reset_ms = 130, + .self_test_ms = 40, +}; + +static const struct adis_timeout adis16495_1_timeouts = { + .reset_ms = 250, + .sw_reset_ms = 210, + .self_test_ms = 20, +}; + static const struct adis16480_chip_info adis16480_chip_info[] = { [ADIS16375] = { .channels = adis16485_channels, @@ -805,6 +838,7 @@ static const struct adis16480_chip_info adis16480_chip_info[] = { .int_clk = 2460000, .max_dec_rate = 2048, .filter_freqs = adis16480_def_filter_freqs, + .timeouts = &adis16485_timeouts, }, [ADIS16480] = { .channels = adis16480_channels, @@ -817,6 +851,7 @@ static const struct adis16480_chip_info adis16480_chip_info[] = { .int_clk = 2460000, .max_dec_rate = 2048, .filter_freqs = adis16480_def_filter_freqs, + .timeouts = &adis16480_timeouts, }, [ADIS16485] = { .channels = adis16485_channels, @@ -829,6 +864,7 @@ static const struct adis16480_chip_info adis16480_chip_info[] = { .int_clk = 2460000, .max_dec_rate = 2048, .filter_freqs = adis16480_def_filter_freqs, + .timeouts = &adis16485_timeouts, }, [ADIS16488] = { .channels = adis16480_channels, @@ -841,6 +877,21 @@ static const struct adis16480_chip_info adis16480_chip_info[] = { .int_clk = 2460000, .max_dec_rate = 2048, .filter_freqs = adis16480_def_filter_freqs, + .timeouts = &adis16485_timeouts, + }, + [ADIS16490] = { + .channels = adis16485_channels, + .num_channels = ARRAY_SIZE(adis16485_channels), + .gyro_max_val = 20000 << 16, + .gyro_max_scale = IIO_DEGREE_TO_RAD(100), + .accel_max_val = IIO_M_S_2_TO_G(16000 << 16), + .accel_max_scale = 8, + .temp_scale = 14285, /* 14.285 milli degree Celsius */ + .int_clk = 4250000, + .max_dec_rate = 4250, + .filter_freqs = adis16495_def_filter_freqs, + .has_pps_clk_mode = true, + .timeouts = &adis16495_timeouts, }, [ADIS16495_1] = { .channels = adis16485_channels, @@ -854,6 +905,7 @@ static const struct adis16480_chip_info adis16480_chip_info[] = { .max_dec_rate = 4250, .filter_freqs = adis16495_def_filter_freqs, .has_pps_clk_mode = true, + .timeouts = &adis16495_1_timeouts, }, [ADIS16495_2] = { .channels = adis16485_channels, @@ -867,6 +919,7 @@ static const struct adis16480_chip_info adis16480_chip_info[] = { .max_dec_rate = 4250, .filter_freqs = adis16495_def_filter_freqs, .has_pps_clk_mode = true, + .timeouts = &adis16495_1_timeouts, }, [ADIS16495_3] = { .channels = adis16485_channels, @@ -880,6 +933,7 @@ static const struct adis16480_chip_info adis16480_chip_info[] = { .max_dec_rate = 4250, .filter_freqs = adis16495_def_filter_freqs, .has_pps_clk_mode = true, + .timeouts = &adis16495_1_timeouts, }, [ADIS16497_1] = { .channels = adis16485_channels, @@ -893,6 +947,7 @@ static const struct adis16480_chip_info adis16480_chip_info[] = { .max_dec_rate = 4250, .filter_freqs = adis16495_def_filter_freqs, .has_pps_clk_mode = true, + .timeouts = &adis16495_1_timeouts, }, [ADIS16497_2] = { .channels = adis16485_channels, @@ -906,6 +961,7 @@ static const struct adis16480_chip_info adis16480_chip_info[] = { .max_dec_rate = 4250, .filter_freqs = adis16495_def_filter_freqs, .has_pps_clk_mode = true, + .timeouts = &adis16495_1_timeouts, }, [ADIS16497_3] = { .channels = adis16485_channels, @@ -919,6 +975,7 @@ static const struct adis16480_chip_info adis16480_chip_info[] = { .max_dec_rate = 4250, .filter_freqs = adis16495_def_filter_freqs, .has_pps_clk_mode = true, + .timeouts = &adis16495_1_timeouts, }, }; @@ -947,14 +1004,14 @@ static int adis16480_enable_irq(struct adis *adis, bool enable) uint16_t val; int ret; - ret = adis_read_reg_16(adis, ADIS16480_REG_FNCTIO_CTRL, &val); + ret = __adis_read_reg_16(adis, ADIS16480_REG_FNCTIO_CTRL, &val); if (ret) return ret; val &= ~ADIS16480_DRDY_EN_MSK; val |= ADIS16480_DRDY_EN(enable); - return adis_write_reg_16(adis, ADIS16480_REG_FNCTIO_CTRL, val); + return __adis_write_reg_16(adis, ADIS16480_REG_FNCTIO_CTRL, val); } static int adis16480_initial_setup(struct iio_dev *indio_dev) @@ -1188,9 +1245,26 @@ static int adis16480_get_ext_clocks(struct adis16480 *st) return 0; } +static struct adis_data *adis16480_adis_data_alloc(struct adis16480 *st, + struct device *dev) +{ + struct adis_data *data; + + data = devm_kmalloc(dev, sizeof(struct adis_data), GFP_KERNEL); + if (!data) + return ERR_PTR(-ENOMEM); + + memcpy(data, &adis16480_data, sizeof(*data)); + + data->timeouts = st->chip_info->timeouts; + + return data; +} + static int adis16480_probe(struct spi_device *spi) { const struct spi_device_id *id = spi_get_device_id(spi); + const struct adis_data *adis16480_data; struct iio_dev *indio_dev; struct adis16480 *st; int ret; @@ -1211,7 +1285,11 @@ static int adis16480_probe(struct spi_device *spi) indio_dev->info = &adis16480_info; indio_dev->modes = INDIO_DIRECT_MODE; - ret = adis_init(&st->adis, indio_dev, spi, &adis16480_data); + adis16480_data = adis16480_adis_data_alloc(st, &spi->dev); + if (IS_ERR(adis16480_data)) + return PTR_ERR(adis16480_data); + + ret = adis_init(&st->adis, indio_dev, spi, adis16480_data); if (ret) return ret; @@ -1278,6 +1356,7 @@ static const struct spi_device_id adis16480_ids[] = { { "adis16480", ADIS16480 }, { "adis16485", ADIS16485 }, { "adis16488", ADIS16488 }, + { "adis16490", ADIS16490 }, { "adis16495-1", ADIS16495_1 }, { "adis16495-2", ADIS16495_2 }, { "adis16495-3", ADIS16495_3 }, @@ -1293,6 +1372,7 @@ static const struct of_device_id adis16480_of_match[] = { { .compatible = "adi,adis16480" }, { .compatible = "adi,adis16485" }, { .compatible = "adi,adis16488" }, + { .compatible = "adi,adis16490" }, { .compatible = "adi,adis16495-1" }, { .compatible = "adi,adis16495-2" }, { .compatible = "adi,adis16495-3" }, diff --git a/drivers/iio/imu/adis_buffer.c b/drivers/iio/imu/adis_buffer.c index 4998a89d083d..3f4dd5c00b03 100644 --- a/drivers/iio/imu/adis_buffer.c +++ b/drivers/iio/imu/adis_buffer.c @@ -129,7 +129,7 @@ static irqreturn_t adis_trigger_handler(int irq, void *p) return -ENOMEM; if (adis->data->has_paging) { - mutex_lock(&adis->txrx_lock); + mutex_lock(&adis->state_lock); if (adis->current_page != 0) { adis->tx[0] = ADIS_WRITE_REG(ADIS_REG_PAGE_ID); adis->tx[1] = 0; @@ -144,7 +144,7 @@ static irqreturn_t adis_trigger_handler(int irq, void *p) if (adis->data->has_paging) { adis->current_page = 0; - mutex_unlock(&adis->txrx_lock); + mutex_unlock(&adis->state_lock); } iio_push_to_buffers_with_timestamp(indio_dev, adis->buffer, diff --git a/drivers/iio/imu/inv_mpu6050/Kconfig b/drivers/iio/imu/inv_mpu6050/Kconfig index e4c4c12236a7..017bc0fcc365 100644 --- a/drivers/iio/imu/inv_mpu6050/Kconfig +++ b/drivers/iio/imu/inv_mpu6050/Kconfig @@ -10,11 +10,12 @@ config INV_MPU6050_IIO config INV_MPU6050_I2C tristate "Invensense MPU6050 devices (I2C)" - depends on I2C_MUX + depends on I2C + select I2C_MUX select INV_MPU6050_IIO select REGMAP_I2C help - This driver supports the Invensense MPU6000/6050/6500/6515, + This driver supports the Invensense MPU6050/6500/6515, MPU9150/9250/9255 and ICM20608/20602 motion tracking devices over I2C. This driver can be built as a module. The module will be called @@ -26,8 +27,8 @@ config INV_MPU6050_SPI select INV_MPU6050_IIO select REGMAP_SPI help - This driver supports the Invensense MPU6000/6050/6500/6515, - MPU9150/9250/9255 and ICM20608/20602 motion tracking devices + This driver supports the Invensense MPU6000/6500/6515, + MPU9250/9255 and ICM20608/20602 motion tracking devices over SPI. This driver can be built as a module. The module will be called inv-mpu6050-spi. diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c index 0686e41bb8a1..5096fc49012d 100644 --- a/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c +++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c @@ -104,6 +104,7 @@ static const struct inv_mpu6050_chip_config chip_config_6050 = { .divider = INV_MPU6050_FIFO_RATE_TO_DIVIDER(INV_MPU6050_INIT_FIFO_RATE), .gyro_fifo_enable = false, .accl_fifo_enable = false, + .temp_fifo_enable = false, .magn_fifo_enable = false, .accl_fs = INV_MPU6050_FS_02G, .user_ctrl = 0, @@ -856,19 +857,27 @@ static const struct iio_chan_spec_ext_info inv_ext_info[] = { .ext_info = inv_ext_info, \ } +#define INV_MPU6050_TEMP_CHAN(_index) \ + { \ + .type = IIO_TEMP, \ + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) \ + | BIT(IIO_CHAN_INFO_OFFSET) \ + | BIT(IIO_CHAN_INFO_SCALE), \ + .scan_index = _index, \ + .scan_type = { \ + .sign = 's', \ + .realbits = 16, \ + .storagebits = 16, \ + .shift = 0, \ + .endianness = IIO_BE, \ + }, \ + } + static const struct iio_chan_spec inv_mpu_channels[] = { IIO_CHAN_SOFT_TIMESTAMP(INV_MPU6050_SCAN_TIMESTAMP), - /* - * Note that temperature should only be via polled reading only, - * not the final scan elements output. - */ - { - .type = IIO_TEMP, - .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) - | BIT(IIO_CHAN_INFO_OFFSET) - | BIT(IIO_CHAN_INFO_SCALE), - .scan_index = -1, - }, + + INV_MPU6050_TEMP_CHAN(INV_MPU6050_SCAN_TEMP), + INV_MPU6050_CHAN(IIO_ANGL_VEL, IIO_MOD_X, INV_MPU6050_SCAN_GYRO_X), INV_MPU6050_CHAN(IIO_ANGL_VEL, IIO_MOD_Y, INV_MPU6050_SCAN_GYRO_Y), INV_MPU6050_CHAN(IIO_ANGL_VEL, IIO_MOD_Z, INV_MPU6050_SCAN_GYRO_Z), @@ -878,22 +887,29 @@ static const struct iio_chan_spec inv_mpu_channels[] = { INV_MPU6050_CHAN(IIO_ACCEL, IIO_MOD_Z, INV_MPU6050_SCAN_ACCL_Z), }; +#define INV_MPU6050_SCAN_MASK_3AXIS_ACCEL \ + (BIT(INV_MPU6050_SCAN_ACCL_X) \ + | BIT(INV_MPU6050_SCAN_ACCL_Y) \ + | BIT(INV_MPU6050_SCAN_ACCL_Z)) + +#define INV_MPU6050_SCAN_MASK_3AXIS_GYRO \ + (BIT(INV_MPU6050_SCAN_GYRO_X) \ + | BIT(INV_MPU6050_SCAN_GYRO_Y) \ + | BIT(INV_MPU6050_SCAN_GYRO_Z)) + +#define INV_MPU6050_SCAN_MASK_TEMP (BIT(INV_MPU6050_SCAN_TEMP)) + static const unsigned long inv_mpu_scan_masks[] = { /* 3-axis accel */ - BIT(INV_MPU6050_SCAN_ACCL_X) - | BIT(INV_MPU6050_SCAN_ACCL_Y) - | BIT(INV_MPU6050_SCAN_ACCL_Z), + INV_MPU6050_SCAN_MASK_3AXIS_ACCEL, + INV_MPU6050_SCAN_MASK_3AXIS_ACCEL | INV_MPU6050_SCAN_MASK_TEMP, /* 3-axis gyro */ - BIT(INV_MPU6050_SCAN_GYRO_X) - | BIT(INV_MPU6050_SCAN_GYRO_Y) - | BIT(INV_MPU6050_SCAN_GYRO_Z), + INV_MPU6050_SCAN_MASK_3AXIS_GYRO, + INV_MPU6050_SCAN_MASK_3AXIS_GYRO | INV_MPU6050_SCAN_MASK_TEMP, /* 6-axis accel + gyro */ - BIT(INV_MPU6050_SCAN_ACCL_X) - | BIT(INV_MPU6050_SCAN_ACCL_Y) - | BIT(INV_MPU6050_SCAN_ACCL_Z) - | BIT(INV_MPU6050_SCAN_GYRO_X) - | BIT(INV_MPU6050_SCAN_GYRO_Y) - | BIT(INV_MPU6050_SCAN_GYRO_Z), + INV_MPU6050_SCAN_MASK_3AXIS_ACCEL | INV_MPU6050_SCAN_MASK_3AXIS_GYRO, + INV_MPU6050_SCAN_MASK_3AXIS_ACCEL | INV_MPU6050_SCAN_MASK_3AXIS_GYRO + | INV_MPU6050_SCAN_MASK_TEMP, 0, }; @@ -915,19 +931,30 @@ static const unsigned long inv_mpu_scan_masks[] = { .ext_info = inv_ext_info, \ } +static const struct iio_chan_spec inv_mpu9150_channels[] = { + IIO_CHAN_SOFT_TIMESTAMP(INV_MPU9X50_SCAN_TIMESTAMP), + + INV_MPU6050_TEMP_CHAN(INV_MPU6050_SCAN_TEMP), + + INV_MPU6050_CHAN(IIO_ANGL_VEL, IIO_MOD_X, INV_MPU6050_SCAN_GYRO_X), + INV_MPU6050_CHAN(IIO_ANGL_VEL, IIO_MOD_Y, INV_MPU6050_SCAN_GYRO_Y), + INV_MPU6050_CHAN(IIO_ANGL_VEL, IIO_MOD_Z, INV_MPU6050_SCAN_GYRO_Z), + + INV_MPU6050_CHAN(IIO_ACCEL, IIO_MOD_X, INV_MPU6050_SCAN_ACCL_X), + INV_MPU6050_CHAN(IIO_ACCEL, IIO_MOD_Y, INV_MPU6050_SCAN_ACCL_Y), + INV_MPU6050_CHAN(IIO_ACCEL, IIO_MOD_Z, INV_MPU6050_SCAN_ACCL_Z), + + /* Magnetometer resolution is 13 bits */ + INV_MPU9X50_MAGN_CHAN(IIO_MOD_X, 13, INV_MPU9X50_SCAN_MAGN_X), + INV_MPU9X50_MAGN_CHAN(IIO_MOD_Y, 13, INV_MPU9X50_SCAN_MAGN_Y), + INV_MPU9X50_MAGN_CHAN(IIO_MOD_Z, 13, INV_MPU9X50_SCAN_MAGN_Z), +}; + static const struct iio_chan_spec inv_mpu9250_channels[] = { IIO_CHAN_SOFT_TIMESTAMP(INV_MPU9X50_SCAN_TIMESTAMP), - /* - * Note that temperature should only be via polled reading only, - * not the final scan elements output. - */ - { - .type = IIO_TEMP, - .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) - | BIT(IIO_CHAN_INFO_OFFSET) - | BIT(IIO_CHAN_INFO_SCALE), - .scan_index = -1, - }, + + INV_MPU6050_TEMP_CHAN(INV_MPU6050_SCAN_TEMP), + INV_MPU6050_CHAN(IIO_ANGL_VEL, IIO_MOD_X, INV_MPU6050_SCAN_GYRO_X), INV_MPU6050_CHAN(IIO_ANGL_VEL, IIO_MOD_Y, INV_MPU6050_SCAN_GYRO_Y), INV_MPU6050_CHAN(IIO_ANGL_VEL, IIO_MOD_Z, INV_MPU6050_SCAN_GYRO_Z), @@ -942,98 +969,50 @@ static const struct iio_chan_spec inv_mpu9250_channels[] = { INV_MPU9X50_MAGN_CHAN(IIO_MOD_Z, 16, INV_MPU9X50_SCAN_MAGN_Z), }; +#define INV_MPU9X50_SCAN_MASK_3AXIS_MAGN \ + (BIT(INV_MPU9X50_SCAN_MAGN_X) \ + | BIT(INV_MPU9X50_SCAN_MAGN_Y) \ + | BIT(INV_MPU9X50_SCAN_MAGN_Z)) + static const unsigned long inv_mpu9x50_scan_masks[] = { /* 3-axis accel */ - BIT(INV_MPU6050_SCAN_ACCL_X) - | BIT(INV_MPU6050_SCAN_ACCL_Y) - | BIT(INV_MPU6050_SCAN_ACCL_Z), + INV_MPU6050_SCAN_MASK_3AXIS_ACCEL, + INV_MPU6050_SCAN_MASK_3AXIS_ACCEL | INV_MPU6050_SCAN_MASK_TEMP, /* 3-axis gyro */ - BIT(INV_MPU6050_SCAN_GYRO_X) - | BIT(INV_MPU6050_SCAN_GYRO_Y) - | BIT(INV_MPU6050_SCAN_GYRO_Z), + INV_MPU6050_SCAN_MASK_3AXIS_GYRO, + INV_MPU6050_SCAN_MASK_3AXIS_GYRO | INV_MPU6050_SCAN_MASK_TEMP, /* 3-axis magn */ - BIT(INV_MPU9X50_SCAN_MAGN_X) - | BIT(INV_MPU9X50_SCAN_MAGN_Y) - | BIT(INV_MPU9X50_SCAN_MAGN_Z), + INV_MPU9X50_SCAN_MASK_3AXIS_MAGN, + INV_MPU9X50_SCAN_MASK_3AXIS_MAGN | INV_MPU6050_SCAN_MASK_TEMP, /* 6-axis accel + gyro */ - BIT(INV_MPU6050_SCAN_ACCL_X) - | BIT(INV_MPU6050_SCAN_ACCL_Y) - | BIT(INV_MPU6050_SCAN_ACCL_Z) - | BIT(INV_MPU6050_SCAN_GYRO_X) - | BIT(INV_MPU6050_SCAN_GYRO_Y) - | BIT(INV_MPU6050_SCAN_GYRO_Z), + INV_MPU6050_SCAN_MASK_3AXIS_ACCEL | INV_MPU6050_SCAN_MASK_3AXIS_GYRO, + INV_MPU6050_SCAN_MASK_3AXIS_ACCEL | INV_MPU6050_SCAN_MASK_3AXIS_GYRO + | INV_MPU6050_SCAN_MASK_TEMP, /* 6-axis accel + magn */ - BIT(INV_MPU6050_SCAN_ACCL_X) - | BIT(INV_MPU6050_SCAN_ACCL_Y) - | BIT(INV_MPU6050_SCAN_ACCL_Z) - | BIT(INV_MPU9X50_SCAN_MAGN_X) - | BIT(INV_MPU9X50_SCAN_MAGN_Y) - | BIT(INV_MPU9X50_SCAN_MAGN_Z), + INV_MPU6050_SCAN_MASK_3AXIS_ACCEL | INV_MPU9X50_SCAN_MASK_3AXIS_MAGN, + INV_MPU6050_SCAN_MASK_3AXIS_ACCEL | INV_MPU9X50_SCAN_MASK_3AXIS_MAGN + | INV_MPU6050_SCAN_MASK_TEMP, /* 6-axis gyro + magn */ - BIT(INV_MPU6050_SCAN_GYRO_X) - | BIT(INV_MPU6050_SCAN_GYRO_Y) - | BIT(INV_MPU6050_SCAN_GYRO_Z) - | BIT(INV_MPU9X50_SCAN_MAGN_X) - | BIT(INV_MPU9X50_SCAN_MAGN_Y) - | BIT(INV_MPU9X50_SCAN_MAGN_Z), + INV_MPU6050_SCAN_MASK_3AXIS_GYRO | INV_MPU9X50_SCAN_MASK_3AXIS_MAGN, + INV_MPU6050_SCAN_MASK_3AXIS_GYRO | INV_MPU9X50_SCAN_MASK_3AXIS_MAGN + | INV_MPU6050_SCAN_MASK_TEMP, /* 9-axis accel + gyro + magn */ - BIT(INV_MPU6050_SCAN_ACCL_X) - | BIT(INV_MPU6050_SCAN_ACCL_Y) - | BIT(INV_MPU6050_SCAN_ACCL_Z) - | BIT(INV_MPU6050_SCAN_GYRO_X) - | BIT(INV_MPU6050_SCAN_GYRO_Y) - | BIT(INV_MPU6050_SCAN_GYRO_Z) - | BIT(INV_MPU9X50_SCAN_MAGN_X) - | BIT(INV_MPU9X50_SCAN_MAGN_Y) - | BIT(INV_MPU9X50_SCAN_MAGN_Z), + INV_MPU6050_SCAN_MASK_3AXIS_ACCEL | INV_MPU6050_SCAN_MASK_3AXIS_GYRO + | INV_MPU9X50_SCAN_MASK_3AXIS_MAGN, + INV_MPU6050_SCAN_MASK_3AXIS_ACCEL | INV_MPU6050_SCAN_MASK_3AXIS_GYRO + | INV_MPU9X50_SCAN_MASK_3AXIS_MAGN + | INV_MPU6050_SCAN_MASK_TEMP, 0, }; -static const struct iio_chan_spec inv_icm20602_channels[] = { - IIO_CHAN_SOFT_TIMESTAMP(INV_ICM20602_SCAN_TIMESTAMP), - { - .type = IIO_TEMP, - .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) - | BIT(IIO_CHAN_INFO_OFFSET) - | BIT(IIO_CHAN_INFO_SCALE), - .scan_index = INV_ICM20602_SCAN_TEMP, - .scan_type = { - .sign = 's', - .realbits = 16, - .storagebits = 16, - .shift = 0, - .endianness = IIO_BE, - }, - }, - - INV_MPU6050_CHAN(IIO_ANGL_VEL, IIO_MOD_X, INV_ICM20602_SCAN_GYRO_X), - INV_MPU6050_CHAN(IIO_ANGL_VEL, IIO_MOD_Y, INV_ICM20602_SCAN_GYRO_Y), - INV_MPU6050_CHAN(IIO_ANGL_VEL, IIO_MOD_Z, INV_ICM20602_SCAN_GYRO_Z), - - INV_MPU6050_CHAN(IIO_ACCEL, IIO_MOD_Y, INV_ICM20602_SCAN_ACCL_Y), - INV_MPU6050_CHAN(IIO_ACCEL, IIO_MOD_X, INV_ICM20602_SCAN_ACCL_X), - INV_MPU6050_CHAN(IIO_ACCEL, IIO_MOD_Z, INV_ICM20602_SCAN_ACCL_Z), -}; - static const unsigned long inv_icm20602_scan_masks[] = { /* 3-axis accel + temp (mandatory) */ - BIT(INV_ICM20602_SCAN_ACCL_X) - | BIT(INV_ICM20602_SCAN_ACCL_Y) - | BIT(INV_ICM20602_SCAN_ACCL_Z) - | BIT(INV_ICM20602_SCAN_TEMP), + INV_MPU6050_SCAN_MASK_3AXIS_ACCEL | INV_MPU6050_SCAN_MASK_TEMP, /* 3-axis gyro + temp (mandatory) */ - BIT(INV_ICM20602_SCAN_GYRO_X) - | BIT(INV_ICM20602_SCAN_GYRO_Y) - | BIT(INV_ICM20602_SCAN_GYRO_Z) - | BIT(INV_ICM20602_SCAN_TEMP), + INV_MPU6050_SCAN_MASK_3AXIS_GYRO | INV_MPU6050_SCAN_MASK_TEMP, /* 6-axis accel + gyro + temp (mandatory) */ - BIT(INV_ICM20602_SCAN_ACCL_X) - | BIT(INV_ICM20602_SCAN_ACCL_Y) - | BIT(INV_ICM20602_SCAN_ACCL_Z) - | BIT(INV_ICM20602_SCAN_GYRO_X) - | BIT(INV_ICM20602_SCAN_GYRO_Y) - | BIT(INV_ICM20602_SCAN_GYRO_Z) - | BIT(INV_ICM20602_SCAN_TEMP), + INV_MPU6050_SCAN_MASK_3AXIS_ACCEL | INV_MPU6050_SCAN_MASK_3AXIS_GYRO + | INV_MPU6050_SCAN_MASK_TEMP, 0, }; @@ -1241,7 +1220,7 @@ int inv_mpu_core_probe(struct regmap *regmap, int irq, const char *name, irq_type = irqd_get_trigger_type(desc); if (!irq_type) irq_type = IRQF_TRIGGER_RISING; - if (irq_type == IRQF_TRIGGER_RISING) + if (irq_type & IRQF_TRIGGER_RISING) // rising or both-edge st->irq_mask = INV_MPU6050_ACTIVE_HIGH; else if (irq_type == IRQF_TRIGGER_FALLING) st->irq_mask = INV_MPU6050_ACTIVE_LOW; @@ -1324,25 +1303,20 @@ int inv_mpu_core_probe(struct regmap *regmap, int irq, const char *name, inv_mpu_bus_setup(indio_dev); switch (chip_type) { + case INV_MPU9150: + indio_dev->channels = inv_mpu9150_channels; + indio_dev->num_channels = ARRAY_SIZE(inv_mpu9150_channels); + indio_dev->available_scan_masks = inv_mpu9x50_scan_masks; + break; case INV_MPU9250: case INV_MPU9255: - /* - * Use magnetometer inside the chip only if there is no i2c - * auxiliary device in use. - */ - if (!st->magn_disabled) { - indio_dev->channels = inv_mpu9250_channels; - indio_dev->num_channels = ARRAY_SIZE(inv_mpu9250_channels); - indio_dev->available_scan_masks = inv_mpu9x50_scan_masks; - } else { - indio_dev->channels = inv_mpu_channels; - indio_dev->num_channels = ARRAY_SIZE(inv_mpu_channels); - indio_dev->available_scan_masks = inv_mpu_scan_masks; - } + indio_dev->channels = inv_mpu9250_channels; + indio_dev->num_channels = ARRAY_SIZE(inv_mpu9250_channels); + indio_dev->available_scan_masks = inv_mpu9x50_scan_masks; break; case INV_ICM20602: - indio_dev->channels = inv_icm20602_channels; - indio_dev->num_channels = ARRAY_SIZE(inv_icm20602_channels); + indio_dev->channels = inv_mpu_channels; + indio_dev->num_channels = ARRAY_SIZE(inv_mpu_channels); indio_dev->available_scan_masks = inv_icm20602_scan_masks; break; default: @@ -1351,6 +1325,15 @@ int inv_mpu_core_probe(struct regmap *regmap, int irq, const char *name, indio_dev->available_scan_masks = inv_mpu_scan_masks; break; } + /* + * Use magnetometer inside the chip only if there is no i2c + * auxiliary device in use. Otherwise Going back to 6-axis only. + */ + if (st->magn_disabled) { + indio_dev->channels = inv_mpu_channels; + indio_dev->num_channels = ARRAY_SIZE(inv_mpu_channels); + indio_dev->available_scan_masks = inv_mpu_scan_masks; + } indio_dev->info = &mpu_info; indio_dev->modes = INDIO_BUFFER_TRIGGERED; diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_i2c.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_i2c.c index 389cc8505e0e..f47a28b4be23 100644 --- a/drivers/iio/imu/inv_mpu6050/inv_mpu_i2c.c +++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_i2c.c @@ -77,6 +77,7 @@ static bool inv_mpu_i2c_aux_bus(struct device *dev) case INV_ICM20602: /* no i2c auxiliary bus on the chip */ return false; + case INV_MPU9150: case INV_MPU9250: case INV_MPU9255: if (st->magn_disabled) @@ -102,6 +103,7 @@ static int inv_mpu_magn_disable(struct iio_dev *indio_dev) struct device_node *mux_node; switch (st->chip_type) { + case INV_MPU9150: case INV_MPU9250: case INV_MPU9255: mux_node = of_get_child_by_name(dev->of_node, "i2c-gate"); diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h b/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h index b096e010d4ee..6158fca7f70e 100644 --- a/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h +++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h @@ -86,6 +86,7 @@ enum inv_devices { * @accl_fs: accel full scale range. * @accl_fifo_enable: enable accel data output * @gyro_fifo_enable: enable gyro data output + * @temp_fifo_enable: enable temp data output * @magn_fifo_enable: enable magn data output * @divider: chip sample rate divider (sample rate divider - 1) */ @@ -95,6 +96,7 @@ struct inv_mpu6050_chip_config { unsigned int accl_fs:2; unsigned int accl_fifo_enable:1; unsigned int gyro_fifo_enable:1; + unsigned int temp_fifo_enable:1; unsigned int magn_fifo_enable:1; u8 divider; u8 user_ctrl; @@ -184,6 +186,7 @@ struct inv_mpu6050_state { #define INV_MPU6050_BIT_SLAVE_2 0x04 #define INV_MPU6050_BIT_ACCEL_OUT 0x08 #define INV_MPU6050_BITS_GYRO_OUT 0x70 +#define INV_MPU6050_BIT_TEMP_OUT 0x80 #define INV_MPU6050_REG_I2C_MST_CTRL 0x24 #define INV_MPU6050_BITS_I2C_MST_CLK_400KHZ 0x0D @@ -268,8 +271,8 @@ struct inv_mpu6050_state { /* MPU9X50 9-axis magnetometer */ #define INV_MPU9X50_BYTES_MAGN 7 -/* ICM20602 FIFO samples include temperature readings */ -#define INV_ICM20602_BYTES_PER_TEMP_SENSOR 2 +/* FIFO temperature sample size */ +#define INV_MPU6050_BYTES_PER_TEMP_SENSOR 2 /* mpu6500 registers */ #define INV_MPU6500_REG_ACCEL_CONFIG_2 0x1D @@ -298,7 +301,7 @@ struct inv_mpu6050_state { #define INV_ICM20608_TEMP_OFFSET 8170 #define INV_ICM20608_TEMP_SCALE 3059976 -/* 6 + 6 + 7 (for MPU9x50) = 19 round up to 24 and plus 8 */ +/* 6 + 6 + 2 + 7 (for MPU9x50) = 21 round up to 24 and plus 8 */ #define INV_MPU6050_OUTPUT_DATA_SIZE 32 #define INV_MPU6050_REG_INT_PIN_CFG 0x37 @@ -344,6 +347,7 @@ enum inv_mpu6050_scan { INV_MPU6050_SCAN_ACCL_X, INV_MPU6050_SCAN_ACCL_Y, INV_MPU6050_SCAN_ACCL_Z, + INV_MPU6050_SCAN_TEMP, INV_MPU6050_SCAN_GYRO_X, INV_MPU6050_SCAN_GYRO_Y, INV_MPU6050_SCAN_GYRO_Z, @@ -355,18 +359,6 @@ enum inv_mpu6050_scan { INV_MPU9X50_SCAN_TIMESTAMP, }; -/* scan element definition for ICM20602, which includes temperature */ -enum inv_icm20602_scan { - INV_ICM20602_SCAN_ACCL_X, - INV_ICM20602_SCAN_ACCL_Y, - INV_ICM20602_SCAN_ACCL_Z, - INV_ICM20602_SCAN_TEMP, - INV_ICM20602_SCAN_GYRO_X, - INV_ICM20602_SCAN_GYRO_Y, - INV_ICM20602_SCAN_GYRO_Z, - INV_ICM20602_SCAN_TIMESTAMP, -}; - enum inv_mpu6050_filter_e { INV_MPU6050_FILTER_256HZ_NOLPF2 = 0, INV_MPU6050_FILTER_188HZ, diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_magn.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_magn.c index 02735af152c8..4f192352521e 100644 --- a/drivers/iio/imu/inv_mpu6050/inv_mpu_magn.c +++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_magn.c @@ -12,7 +12,9 @@ #include "inv_mpu_magn.h" /* - * MPU9250 magnetometer is an AKM AK8963 chip on I2C aux bus + * MPU9xxx magnetometer are AKM chips on I2C aux bus + * MPU9150 is AK8975 + * MPU9250 is AK8963 */ #define INV_MPU_MAGN_I2C_ADDR 0x0C @@ -33,10 +35,10 @@ #define INV_MPU_MAGN_BITS_MODE_PWDN 0x00 #define INV_MPU_MAGN_BITS_MODE_SINGLE 0x01 #define INV_MPU_MAGN_BITS_MODE_FUSE 0x0F -#define INV_MPU_MAGN_BIT_OUTPUT_BIT 0x10 +#define INV_MPU9250_MAGN_BIT_OUTPUT_BIT 0x10 -#define INV_MPU_MAGN_REG_CNTL2 0x0B -#define INV_MPU_MAGN_BIT_SRST 0x01 +#define INV_MPU9250_MAGN_REG_CNTL2 0x0B +#define INV_MPU9250_MAGN_BIT_SRST 0x01 #define INV_MPU_MAGN_REG_ASAX 0x10 #define INV_MPU_MAGN_REG_ASAY 0x11 @@ -48,6 +50,7 @@ static bool inv_magn_supported(const struct inv_mpu6050_state *st) { switch (st->chip_type) { + case INV_MPU9150: case INV_MPU9250: case INV_MPU9255: return true; @@ -61,6 +64,7 @@ static int inv_magn_init(struct inv_mpu6050_state *st) { uint8_t val; uint8_t asa[3]; + int32_t sensitivity; int ret; /* check whoami */ @@ -71,12 +75,19 @@ static int inv_magn_init(struct inv_mpu6050_state *st) if (val != INV_MPU_MAGN_BITS_WIA) return -ENODEV; - /* reset chip */ - ret = inv_mpu_aux_write(st, INV_MPU_MAGN_I2C_ADDR, - INV_MPU_MAGN_REG_CNTL2, - INV_MPU_MAGN_BIT_SRST); - if (ret) - return ret; + /* software reset for MPU925x only */ + switch (st->chip_type) { + case INV_MPU9250: + case INV_MPU9255: + ret = inv_mpu_aux_write(st, INV_MPU_MAGN_I2C_ADDR, + INV_MPU9250_MAGN_REG_CNTL2, + INV_MPU9250_MAGN_BIT_SRST); + if (ret) + return ret; + break; + default: + break; + } /* read fuse ROM data */ ret = inv_mpu_aux_write(st, INV_MPU_MAGN_I2C_ADDR, @@ -98,22 +109,36 @@ static int inv_magn_init(struct inv_mpu6050_state *st) return ret; /* + * Sensor sentivity + * 1 uT = 0.01 G and value is in micron (1e6) + * sensitvity = x uT * 0.01 * 1e6 + */ + switch (st->chip_type) { + case INV_MPU9150: + /* sensor sensitivity is 0.3 uT */ + sensitivity = 3000; + break; + case INV_MPU9250: + case INV_MPU9255: + /* sensor sensitivity in 16 bits mode: 0.15 uT */ + sensitivity = 1500; + break; + default: + return -EINVAL; + } + + /* * Sensitivity adjustement and scale to Gauss * * Hadj = H * (((ASA - 128) * 0.5 / 128) + 1) * Factor simplification: * Hadj = H * ((ASA + 128) / 256) * - * Sensor sentivity - * 0.15 uT in 16 bits mode - * 1 uT = 0.01 G and value is in micron (1e6) - * sensitvity = 0.15 uT * 0.01 * 1e6 - * - * raw_to_gauss = Hadj * 1500 + * raw_to_gauss = Hadj * sensitivity */ - st->magn_raw_to_gauss[0] = (((int32_t)asa[0] + 128) * 1500) / 256; - st->magn_raw_to_gauss[1] = (((int32_t)asa[1] + 128) * 1500) / 256; - st->magn_raw_to_gauss[2] = (((int32_t)asa[2] + 128) * 1500) / 256; + st->magn_raw_to_gauss[0] = (((int32_t)asa[0] + 128) * sensitivity) / 256; + st->magn_raw_to_gauss[1] = (((int32_t)asa[1] + 128) * sensitivity) / 256; + st->magn_raw_to_gauss[2] = (((int32_t)asa[2] + 128) * sensitivity) / 256; return 0; } @@ -129,6 +154,7 @@ static int inv_magn_init(struct inv_mpu6050_state *st) */ int inv_mpu_magn_probe(struct inv_mpu6050_state *st) { + uint8_t val; int ret; /* quit if chip is not supported */ @@ -179,10 +205,17 @@ int inv_mpu_magn_probe(struct inv_mpu6050_state *st) if (ret) return ret; - /* add 16 bits mode */ - ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_DO(1), - INV_MPU_MAGN_BITS_MODE_SINGLE | - INV_MPU_MAGN_BIT_OUTPUT_BIT); + /* add 16 bits mode for MPU925x */ + val = INV_MPU_MAGN_BITS_MODE_SINGLE; + switch (st->chip_type) { + case INV_MPU9250: + case INV_MPU9255: + val |= INV_MPU9250_MAGN_BIT_OUTPUT_BIT; + break; + default: + break; + } + ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_DO(1), val); if (ret) return ret; @@ -237,6 +270,7 @@ int inv_mpu_magn_set_orient(struct inv_mpu6050_state *st) /* fill magnetometer orientation */ switch (st->chip_type) { + case INV_MPU9150: case INV_MPU9250: case INV_MPU9255: /* x <- y */ diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c index 10d16ec5104b..f9fdf4302a91 100644 --- a/drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c +++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c @@ -142,6 +142,8 @@ int inv_reset_fifo(struct iio_dev *indio_dev) d |= INV_MPU6050_BITS_GYRO_OUT; if (st->chip_config.accl_fifo_enable) d |= INV_MPU6050_BIT_ACCEL_OUT; + if (st->chip_config.temp_fifo_enable) + d |= INV_MPU6050_BIT_TEMP_OUT; if (st->chip_config.magn_fifo_enable) d |= INV_MPU6050_BIT_SLAVE_0; result = regmap_write(st->map, st->reg->fifo_en, d); @@ -183,11 +185,8 @@ irqreturn_t inv_mpu6050_read_fifo(int irq, void *p) "failed to ack interrupt\n"); goto flush_fifo; } - if (!(int_status & INV_MPU6050_BIT_RAW_DATA_RDY_INT)) { - dev_warn(regmap_get_device(st->map), - "spurious interrupt with status 0x%x\n", int_status); + if (!(int_status & INV_MPU6050_BIT_RAW_DATA_RDY_INT)) goto end_session; - } if (!(st->chip_config.accl_fifo_enable | st->chip_config.gyro_fifo_enable | @@ -200,8 +199,8 @@ irqreturn_t inv_mpu6050_read_fifo(int irq, void *p) if (st->chip_config.gyro_fifo_enable) bytes_per_datum += INV_MPU6050_BYTES_PER_3AXIS_SENSOR; - if (st->chip_type == INV_ICM20602) - bytes_per_datum += INV_ICM20602_BYTES_PER_TEMP_SENSOR; + if (st->chip_config.temp_fifo_enable) + bytes_per_datum += INV_MPU6050_BYTES_PER_TEMP_SENSOR; if (st->chip_config.magn_fifo_enable) bytes_per_datum += INV_MPU9X50_BYTES_MAGN; diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_spi.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_spi.c index 142692fc0758..ec102d5a5c77 100644 --- a/drivers/iio/imu/inv_mpu6050/inv_mpu_spi.c +++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_spi.c @@ -74,7 +74,6 @@ static int inv_mpu_probe(struct spi_device *spi) static const struct spi_device_id inv_mpu_id[] = { {"mpu6000", INV_MPU6000}, {"mpu6500", INV_MPU6500}, - {"mpu9150", INV_MPU9150}, {"mpu9250", INV_MPU9250}, {"mpu9255", INV_MPU9255}, {"icm20608", INV_ICM20608}, diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_trigger.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_trigger.c index d7d951927a44..5199fe790c30 100644 --- a/drivers/iio/imu/inv_mpu6050/inv_mpu_trigger.c +++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_trigger.c @@ -24,6 +24,9 @@ static void inv_scan_query_mpu6050(struct iio_dev *indio_dev) indio_dev->active_scan_mask) || test_bit(INV_MPU6050_SCAN_ACCL_Z, indio_dev->active_scan_mask); + + st->chip_config.temp_fifo_enable = + test_bit(INV_MPU6050_SCAN_TEMP, indio_dev->active_scan_mask); } static void inv_scan_query_mpu9x50(struct iio_dev *indio_dev) @@ -50,6 +53,7 @@ static void inv_scan_query(struct iio_dev *indio_dev) struct inv_mpu6050_state *st = iio_priv(indio_dev); switch (st->chip_type) { + case INV_MPU9150: case INV_MPU9250: case INV_MPU9255: return inv_scan_query_mpu9x50(indio_dev); diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h index dc55d7dff3eb..9c3486a8134f 100644 --- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h +++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h @@ -76,6 +76,7 @@ enum st_lsm6dsx_hw_id { .endianness = IIO_LE, \ }, \ .event_spec = &st_lsm6dsx_event, \ + .ext_info = st_lsm6dsx_accel_ext_info, \ .num_event_specs = 1, \ } @@ -176,21 +177,38 @@ struct st_lsm6dsx_hw_ts_settings { * @pullup_en: i2c controller pull-up register info (addr + mask). * @aux_sens: aux sensor register info (addr + mask). * @wr_once: write_once register info (addr + mask). + * @emb_func: embedded function register info (addr + mask). + * @num_ext_dev: max number of slave devices. * @shub_out: sensor hub first output register info. * @slv0_addr: slave0 address in secondary page. * @dw_slv0_addr: slave0 write register address in secondary page. * @batch_en: Enable/disable FIFO batching. + * @pause: controller pause value. */ struct st_lsm6dsx_shub_settings { struct st_lsm6dsx_reg page_mux; - struct st_lsm6dsx_reg master_en; - struct st_lsm6dsx_reg pullup_en; + struct { + bool sec_page; + u8 addr; + u8 mask; + } master_en; + struct { + bool sec_page; + u8 addr; + u8 mask; + } pullup_en; struct st_lsm6dsx_reg aux_sens; struct st_lsm6dsx_reg wr_once; - u8 shub_out; + struct st_lsm6dsx_reg emb_func; + u8 num_ext_dev; + struct { + bool sec_page; + u8 addr; + } shub_out; u8 slv0_addr; u8 dw_slv0_addr; u8 batch_en; + u8 pause; }; struct st_lsm6dsx_event_settings { @@ -361,6 +379,7 @@ struct st_lsm6dsx_sensor { * @enable_event: enabled event bitmask. * @iio_devs: Pointers to acc/gyro iio_dev instances. * @settings: Pointer to the specific sensor settings in use. + * @orientation: sensor chip orientation relative to main hardware. */ struct st_lsm6dsx_hw { struct device *dev; @@ -387,16 +406,21 @@ struct st_lsm6dsx_hw { struct iio_dev *iio_devs[ST_LSM6DSX_ID_MAX]; const struct st_lsm6dsx_settings *settings; + + struct iio_mount_matrix orientation; }; -static const struct iio_event_spec st_lsm6dsx_event = { +static __maybe_unused const struct iio_event_spec st_lsm6dsx_event = { .type = IIO_EV_TYPE_THRESH, .dir = IIO_EV_DIR_EITHER, .mask_separate = BIT(IIO_EV_INFO_VALUE) | BIT(IIO_EV_INFO_ENABLE) }; -static const unsigned long st_lsm6dsx_available_scan_masks[] = {0x7, 0x0}; +static __maybe_unused const unsigned long st_lsm6dsx_available_scan_masks[] = { + 0x7, 0x0, +}; + extern const struct dev_pm_ops st_lsm6dsx_pm_ops; int st_lsm6dsx_probe(struct device *dev, int irq, int hw_id, @@ -457,4 +481,19 @@ st_lsm6dsx_write_locked(struct st_lsm6dsx_hw *hw, unsigned int addr, return err; } +static const inline struct iio_mount_matrix * +st_lsm6dsx_get_mount_matrix(const struct iio_dev *iio_dev, + const struct iio_chan_spec *chan) +{ + struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); + struct st_lsm6dsx_hw *hw = sensor->hw; + + return &hw->orientation; +} + +static const struct iio_chan_spec_ext_info st_lsm6dsx_accel_ext_info[] = { + IIO_MOUNT_MATRIX(IIO_SHARED_BY_ALL, st_lsm6dsx_get_mount_matrix), + { } +}; + #endif /* ST_LSM6DSX_H */ diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c index cb536b81a1c2..bb899345f2bb 100644 --- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c +++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c @@ -336,12 +336,13 @@ static inline int st_lsm6dsx_read_block(struct st_lsm6dsx_hw *hw, u8 addr, */ int st_lsm6dsx_read_fifo(struct st_lsm6dsx_hw *hw) { + struct st_lsm6dsx_sensor *acc_sensor, *gyro_sensor, *ext_sensor = NULL; + int err, acc_sip, gyro_sip, ts_sip, ext_sip, read_len, offset; u16 fifo_len, pattern_len = hw->sip * ST_LSM6DSX_SAMPLE_SIZE; u16 fifo_diff_mask = hw->settings->fifo_ops.fifo_diff.mask; - int err, acc_sip, gyro_sip, ts_sip, read_len, offset; - struct st_lsm6dsx_sensor *acc_sensor, *gyro_sensor; u8 gyro_buff[ST_LSM6DSX_IIO_BUFF_SIZE]; u8 acc_buff[ST_LSM6DSX_IIO_BUFF_SIZE]; + u8 ext_buff[ST_LSM6DSX_IIO_BUFF_SIZE]; bool reset_ts = false; __le16 fifo_status; s64 ts = 0; @@ -364,6 +365,8 @@ int st_lsm6dsx_read_fifo(struct st_lsm6dsx_hw *hw) acc_sensor = iio_priv(hw->iio_devs[ST_LSM6DSX_ID_ACC]); gyro_sensor = iio_priv(hw->iio_devs[ST_LSM6DSX_ID_GYRO]); + if (hw->iio_devs[ST_LSM6DSX_ID_EXT0]) + ext_sensor = iio_priv(hw->iio_devs[ST_LSM6DSX_ID_EXT0]); for (read_len = 0; read_len < fifo_len; read_len += pattern_len) { err = st_lsm6dsx_read_block(hw, ST_LSM6DSX_REG_FIFO_OUTL_ADDR, @@ -391,12 +394,13 @@ int st_lsm6dsx_read_fifo(struct st_lsm6dsx_hw *hw) * following pattern is repeated every 9 samples: * - Gx, Gy, Gz, Ax, Ay, Az, Ts, Gx, Gy, Gz, Ts, Gx, .. */ + ext_sip = ext_sensor ? ext_sensor->sip : 0; gyro_sip = gyro_sensor->sip; acc_sip = acc_sensor->sip; ts_sip = hw->ts_sip; offset = 0; - while (acc_sip > 0 || gyro_sip > 0) { + while (acc_sip > 0 || gyro_sip > 0 || ext_sip > 0) { if (gyro_sip > 0) { memcpy(gyro_buff, &hw->buff[offset], ST_LSM6DSX_SAMPLE_SIZE); @@ -407,6 +411,11 @@ int st_lsm6dsx_read_fifo(struct st_lsm6dsx_hw *hw) ST_LSM6DSX_SAMPLE_SIZE); offset += ST_LSM6DSX_SAMPLE_SIZE; } + if (ext_sip > 0) { + memcpy(ext_buff, &hw->buff[offset], + ST_LSM6DSX_SAMPLE_SIZE); + offset += ST_LSM6DSX_SAMPLE_SIZE; + } if (ts_sip-- > 0) { u8 data[ST_LSM6DSX_SAMPLE_SIZE]; @@ -440,6 +449,10 @@ int st_lsm6dsx_read_fifo(struct st_lsm6dsx_hw *hw) iio_push_to_buffers_with_timestamp( hw->iio_devs[ST_LSM6DSX_ID_ACC], acc_buff, acc_sensor->ts_ref + ts); + if (ext_sip-- > 0) + iio_push_to_buffers_with_timestamp( + hw->iio_devs[ST_LSM6DSX_ID_EXT0], + ext_buff, ext_sensor->ts_ref + ts); } } @@ -638,12 +651,12 @@ int st_lsm6dsx_update_fifo(struct st_lsm6dsx_sensor *sensor, bool enable) err = st_lsm6dsx_sensor_set_enable(sensor, enable); if (err < 0) goto out; - - err = st_lsm6dsx_set_fifo_odr(sensor, enable); - if (err < 0) - goto out; } + err = st_lsm6dsx_set_fifo_odr(sensor, enable); + if (err < 0) + goto out; + err = st_lsm6dsx_update_decimators(hw); if (err < 0) goto out; diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c index b921dd9e108f..84d219ae6aee 100644 --- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c +++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c @@ -54,6 +54,7 @@ #include <linux/interrupt.h> #include <linux/irq.h> #include <linux/pm.h> +#include <linux/property.h> #include <linux/regmap.h> #include <linux/bitfield.h> @@ -655,6 +656,10 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { .addr = 0x08, .mask = GENMASK(5, 3), }, + [ST_LSM6DSX_ID_EXT0] = { + .addr = 0x09, + .mask = GENMASK(2, 0), + }, }, .fifo_ops = { .update_fifo = st_lsm6dsx_update_fifo, @@ -687,6 +692,39 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { .mask = GENMASK(5, 3), }, }, + .shub_settings = { + .page_mux = { + .addr = 0x01, + .mask = BIT(7), + }, + .master_en = { + .addr = 0x1a, + .mask = BIT(0), + }, + .pullup_en = { + .addr = 0x1a, + .mask = BIT(3), + }, + .aux_sens = { + .addr = 0x04, + .mask = GENMASK(5, 4), + }, + .wr_once = { + .addr = 0x07, + .mask = BIT(5), + }, + .emb_func = { + .addr = 0x19, + .mask = BIT(2), + }, + .num_ext_dev = 1, + .shub_out = { + .addr = 0x2e, + }, + .slv0_addr = 0x02, + .dw_slv0_addr = 0x0e, + .pause = 0x7, + }, .event_settings = { .enable_reg = { .addr = 0x58, @@ -867,10 +905,12 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { .mask = BIT(6), }, .master_en = { + .sec_page = true, .addr = 0x14, .mask = BIT(2), }, .pullup_en = { + .sec_page = true, .addr = 0x14, .mask = BIT(3), }, @@ -882,7 +922,11 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { .addr = 0x14, .mask = BIT(6), }, - .shub_out = 0x02, + .num_ext_dev = 3, + .shub_out = { + .sec_page = true, + .addr = 0x02, + }, .slv0_addr = 0x15, .dw_slv0_addr = 0x21, .batch_en = BIT(3), @@ -1241,10 +1285,12 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { .mask = BIT(6), }, .master_en = { + .sec_page = true, .addr = 0x14, .mask = BIT(2), }, .pullup_en = { + .sec_page = true, .addr = 0x14, .mask = BIT(3), }, @@ -1256,7 +1302,11 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { .addr = 0x14, .mask = BIT(6), }, - .shub_out = 0x02, + .num_ext_dev = 3, + .shub_out = { + .sec_page = true, + .addr = 0x02, + }, .slv0_addr = 0x15, .dw_slv0_addr = 0x21, .batch_en = BIT(3), @@ -1506,8 +1556,11 @@ static int st_lsm6dsx_read_oneshot(struct st_lsm6dsx_sensor *sensor, if (err < 0) return err; - if (!hw->enable_event) - st_lsm6dsx_sensor_set_enable(sensor, false); + if (!hw->enable_event) { + err = st_lsm6dsx_sensor_set_enable(sensor, false); + if (err < 0) + return err; + } *val = (s16)le16_to_cpu(data); @@ -1609,11 +1662,11 @@ static int st_lsm6dsx_event_setup(struct st_lsm6dsx_hw *hw, int state) } static int st_lsm6dsx_read_event(struct iio_dev *iio_dev, - const struct iio_chan_spec *chan, - enum iio_event_type type, - enum iio_event_direction dir, - enum iio_event_info info, - int *val, int *val2) + const struct iio_chan_spec *chan, + enum iio_event_type type, + enum iio_event_direction dir, + enum iio_event_info info, + int *val, int *val2) { struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); struct st_lsm6dsx_hw *hw = sensor->hw; @@ -1827,14 +1880,14 @@ static const struct iio_info st_lsm6dsx_gyro_info = { .hwfifo_set_watermark = st_lsm6dsx_set_watermark, }; -static int st_lsm6dsx_of_get_drdy_pin(struct st_lsm6dsx_hw *hw, int *drdy_pin) +static int st_lsm6dsx_get_drdy_pin(struct st_lsm6dsx_hw *hw, int *drdy_pin) { - struct device_node *np = hw->dev->of_node; + struct device *dev = hw->dev; - if (!np) + if (!dev_fwnode(dev)) return -EINVAL; - return of_property_read_u32(np, "st,drdy-int-pin", drdy_pin); + return device_property_read_u32(dev, "st,drdy-int-pin", drdy_pin); } static int @@ -1843,7 +1896,7 @@ st_lsm6dsx_get_drdy_reg(struct st_lsm6dsx_hw *hw, { int err = 0, drdy_pin; - if (st_lsm6dsx_of_get_drdy_pin(hw, &drdy_pin) < 0) { + if (st_lsm6dsx_get_drdy_pin(hw, &drdy_pin) < 0) { struct st_sensors_platform_data *pdata; struct device *dev = hw->dev; @@ -1872,26 +1925,29 @@ st_lsm6dsx_get_drdy_reg(struct st_lsm6dsx_hw *hw, static int st_lsm6dsx_init_shub(struct st_lsm6dsx_hw *hw) { const struct st_lsm6dsx_shub_settings *hub_settings; - struct device_node *np = hw->dev->of_node; struct st_sensors_platform_data *pdata; + struct device *dev = hw->dev; unsigned int data; int err = 0; hub_settings = &hw->settings->shub_settings; - pdata = (struct st_sensors_platform_data *)hw->dev->platform_data; - if ((np && of_property_read_bool(np, "st,pullups")) || + pdata = (struct st_sensors_platform_data *)dev->platform_data; + if ((dev_fwnode(dev) && device_property_read_bool(dev, "st,pullups")) || (pdata && pdata->pullups)) { - err = st_lsm6dsx_set_page(hw, true); - if (err < 0) - return err; + if (hub_settings->pullup_en.sec_page) { + err = st_lsm6dsx_set_page(hw, true); + if (err < 0) + return err; + } data = ST_LSM6DSX_SHIFT_VAL(1, hub_settings->pullup_en.mask); err = regmap_update_bits(hw->regmap, hub_settings->pullup_en.addr, hub_settings->pullup_en.mask, data); - st_lsm6dsx_set_page(hw, false); + if (hub_settings->pullup_en.sec_page) + st_lsm6dsx_set_page(hw, false); if (err < 0) return err; @@ -1909,6 +1965,16 @@ static int st_lsm6dsx_init_shub(struct st_lsm6dsx_hw *hw) hub_settings->aux_sens.mask, data); st_lsm6dsx_set_page(hw, false); + + if (err < 0) + return err; + } + + if (hub_settings->emb_func.addr) { + data = ST_LSM6DSX_SHIFT_VAL(1, hub_settings->emb_func.mask); + err = regmap_update_bits(hw->regmap, + hub_settings->emb_func.addr, + hub_settings->emb_func.mask, data); } return err; @@ -2158,9 +2224,9 @@ static irqreturn_t st_lsm6dsx_handler_thread(int irq, void *private) static int st_lsm6dsx_irq_setup(struct st_lsm6dsx_hw *hw) { - struct device_node *np = hw->dev->of_node; struct st_sensors_platform_data *pdata; const struct st_lsm6dsx_reg *reg; + struct device *dev = hw->dev; unsigned long irq_type; bool irq_active_low; int err; @@ -2188,8 +2254,8 @@ static int st_lsm6dsx_irq_setup(struct st_lsm6dsx_hw *hw) if (err < 0) return err; - pdata = (struct st_sensors_platform_data *)hw->dev->platform_data; - if ((np && of_property_read_bool(np, "drive-open-drain")) || + pdata = (struct st_sensors_platform_data *)dev->platform_data; + if ((dev_fwnode(dev) && device_property_read_bool(dev, "drive-open-drain")) || (pdata && pdata->open_drain)) { reg = &hw->settings->irq_config.od; err = regmap_update_bits(hw->regmap, reg->addr, reg->mask, @@ -2219,7 +2285,6 @@ int st_lsm6dsx_probe(struct device *dev, int irq, int hw_id, { struct st_sensors_platform_data *pdata = dev->platform_data; const struct st_lsm6dsx_shub_settings *hub_settings; - struct device_node *np = dev->of_node; struct st_lsm6dsx_hw *hw; const char *name = NULL; int i, err; @@ -2273,6 +2338,10 @@ int st_lsm6dsx_probe(struct device *dev, int irq, int hw_id, return err; } + err = iio_read_mount_matrix(hw->dev, "mount-matrix", &hw->orientation); + if (err) + return err; + for (i = 0; i < ST_LSM6DSX_ID_MAX; i++) { if (!hw->iio_devs[i]) continue; @@ -2282,7 +2351,7 @@ int st_lsm6dsx_probe(struct device *dev, int irq, int hw_id, return err; } - if ((np && of_property_read_bool(np, "wakeup-source")) || + if ((dev_fwnode(dev) && device_property_read_bool(dev, "wakeup-source")) || (pdata && pdata->wakeup_source)) device_init_wakeup(dev, true); diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_i2c.c b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_i2c.c index cd47ec1fedcb..0fb32131afce 100644 --- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_i2c.c +++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_i2c.c @@ -12,7 +12,6 @@ #include <linux/module.h> #include <linux/i2c.h> #include <linux/slab.h> -#include <linux/of.h> #include <linux/regmap.h> #include "st_lsm6dsx.h" @@ -122,7 +121,7 @@ static struct i2c_driver st_lsm6dsx_driver = { .driver = { .name = "st_lsm6dsx_i2c", .pm = &st_lsm6dsx_pm_ops, - .of_match_table = of_match_ptr(st_lsm6dsx_i2c_of_match), + .of_match_table = st_lsm6dsx_i2c_of_match, }, .probe = st_lsm6dsx_i2c_probe, .id_table = st_lsm6dsx_i2c_id_table, diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c index fa5d1001a46c..eea555617d4a 100644 --- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c +++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c @@ -30,7 +30,6 @@ #include "st_lsm6dsx.h" -#define ST_LSM6DSX_MAX_SLV_NUM 3 #define ST_LSM6DSX_SLV_ADDR(n, base) ((base) + (n) * 3) #define ST_LSM6DSX_SLV_SUB_ADDR(n, base) ((base) + 1 + (n) * 3) #define ST_LSM6DSX_SLV_CONFIG(n, base) ((base) + 2 + (n) * 3) @@ -102,24 +101,31 @@ static void st_lsm6dsx_shub_wait_complete(struct st_lsm6dsx_hw *hw) } /** - * st_lsm6dsx_shub_read_reg - read i2c controller register + * st_lsm6dsx_shub_read_output - read i2c controller register * * Read st_lsm6dsx i2c controller register */ -static int st_lsm6dsx_shub_read_reg(struct st_lsm6dsx_hw *hw, u8 addr, - u8 *data, int len) +static int +st_lsm6dsx_shub_read_output(struct st_lsm6dsx_hw *hw, u8 *data, + int len) { + const struct st_lsm6dsx_shub_settings *hub_settings; int err; mutex_lock(&hw->page_lock); - err = st_lsm6dsx_set_page(hw, true); - if (err < 0) - goto out; + hub_settings = &hw->settings->shub_settings; + if (hub_settings->shub_out.sec_page) { + err = st_lsm6dsx_set_page(hw, true); + if (err < 0) + goto out; + } - err = regmap_bulk_read(hw->regmap, addr, data, len); + err = regmap_bulk_read(hw->regmap, hub_settings->shub_out.addr, + data, len); - st_lsm6dsx_set_page(hw, false); + if (hub_settings->shub_out.sec_page) + st_lsm6dsx_set_page(hw, false); out: mutex_unlock(&hw->page_lock); @@ -186,15 +192,18 @@ static int st_lsm6dsx_shub_master_enable(struct st_lsm6dsx_sensor *sensor, mutex_lock(&hw->page_lock); hub_settings = &hw->settings->shub_settings; - err = st_lsm6dsx_set_page(hw, true); - if (err < 0) - goto out; + if (hub_settings->master_en.sec_page) { + err = st_lsm6dsx_set_page(hw, true); + if (err < 0) + goto out; + } data = ST_LSM6DSX_SHIFT_VAL(enable, hub_settings->master_en.mask); err = regmap_update_bits(hw->regmap, hub_settings->master_en.addr, hub_settings->master_en.mask, data); - st_lsm6dsx_set_page(hw, false); + if (hub_settings->master_en.sec_page) + st_lsm6dsx_set_page(hw, false); out: mutex_unlock(&hw->page_lock); @@ -212,16 +221,21 @@ st_lsm6dsx_shub_read(struct st_lsm6dsx_sensor *sensor, u8 addr, u8 *data, int len) { const struct st_lsm6dsx_shub_settings *hub_settings; + u8 config[3], slv_addr, slv_config = 0; struct st_lsm6dsx_hw *hw = sensor->hw; - u8 config[3], slv_addr; + const struct st_lsm6dsx_reg *aux_sens; int err; hub_settings = &hw->settings->shub_settings; slv_addr = ST_LSM6DSX_SLV_ADDR(0, hub_settings->slv0_addr); + aux_sens = &hw->settings->shub_settings.aux_sens; + /* do not overwrite aux_sens */ + if (slv_addr + 2 == aux_sens->addr) + slv_config = ST_LSM6DSX_SHIFT_VAL(3, aux_sens->mask); config[0] = (sensor->ext_info.addr << 1) | 1; config[1] = addr; - config[2] = len & ST_LS6DSX_READ_OP_MASK; + config[2] = (len & ST_LS6DSX_READ_OP_MASK) | slv_config; err = st_lsm6dsx_shub_write_reg(hw, slv_addr, config, sizeof(config)); @@ -234,12 +248,14 @@ st_lsm6dsx_shub_read(struct st_lsm6dsx_sensor *sensor, u8 addr, st_lsm6dsx_shub_wait_complete(hw); - err = st_lsm6dsx_shub_read_reg(hw, hub_settings->shub_out, data, - len & ST_LS6DSX_READ_OP_MASK); + err = st_lsm6dsx_shub_read_output(hw, data, + len & ST_LS6DSX_READ_OP_MASK); st_lsm6dsx_shub_master_enable(sensor, false); - memset(config, 0, sizeof(config)); + config[0] = hub_settings->pause; + config[1] = 0; + config[2] = slv_config; return st_lsm6dsx_shub_write_reg(hw, slv_addr, config, sizeof(config)); } @@ -296,7 +312,8 @@ st_lsm6dsx_shub_write(struct st_lsm6dsx_sensor *sensor, u8 addr, st_lsm6dsx_shub_master_enable(sensor, false); } - memset(config, 0, sizeof(config)); + config[0] = hub_settings->pause; + config[1] = 0; return st_lsm6dsx_shub_write_reg(hw, slv_addr, config, sizeof(config)); } @@ -688,14 +705,19 @@ st_lsm6dsx_shub_check_wai(struct st_lsm6dsx_hw *hw, u8 *i2c_addr, const struct st_lsm6dsx_ext_dev_settings *settings) { const struct st_lsm6dsx_shub_settings *hub_settings; + u8 config[3], data, slv_addr, slv_config = 0; + const struct st_lsm6dsx_reg *aux_sens; struct st_lsm6dsx_sensor *sensor; - u8 config[3], data, slv_addr; bool found = false; int i, err; + sensor = iio_priv(hw->iio_devs[ST_LSM6DSX_ID_ACC]); hub_settings = &hw->settings->shub_settings; + aux_sens = &hw->settings->shub_settings.aux_sens; slv_addr = ST_LSM6DSX_SLV_ADDR(0, hub_settings->slv0_addr); - sensor = iio_priv(hw->iio_devs[ST_LSM6DSX_ID_ACC]); + /* do not overwrite aux_sens */ + if (slv_addr + 2 == aux_sens->addr) + slv_config = ST_LSM6DSX_SHIFT_VAL(3, aux_sens->mask); for (i = 0; i < ARRAY_SIZE(settings->i2c_addr); i++) { if (!settings->i2c_addr[i]) @@ -704,7 +726,7 @@ st_lsm6dsx_shub_check_wai(struct st_lsm6dsx_hw *hw, u8 *i2c_addr, /* read wai slave register */ config[0] = (settings->i2c_addr[i] << 1) | 0x1; config[1] = settings->wai.addr; - config[2] = 0x1; + config[2] = 0x1 | slv_config; err = st_lsm6dsx_shub_write_reg(hw, slv_addr, config, sizeof(config)); @@ -717,9 +739,7 @@ st_lsm6dsx_shub_check_wai(struct st_lsm6dsx_hw *hw, u8 *i2c_addr, st_lsm6dsx_shub_wait_complete(hw); - err = st_lsm6dsx_shub_read_reg(hw, - hub_settings->shub_out, - &data, sizeof(data)); + err = st_lsm6dsx_shub_read_output(hw, &data, sizeof(data)); st_lsm6dsx_shub_master_enable(sensor, false); @@ -735,7 +755,9 @@ st_lsm6dsx_shub_check_wai(struct st_lsm6dsx_hw *hw, u8 *i2c_addr, } /* reset SLV0 channel */ - memset(config, 0, sizeof(config)); + config[0] = hub_settings->pause; + config[1] = 0; + config[2] = slv_config; err = st_lsm6dsx_shub_write_reg(hw, slv_addr, config, sizeof(config)); if (err < 0) @@ -770,7 +792,7 @@ int st_lsm6dsx_shub_probe(struct st_lsm6dsx_hw *hw, const char *name) if (err < 0) return err; - if (++num_ext_dev >= ST_LSM6DSX_MAX_SLV_NUM) + if (++num_ext_dev >= hw->settings->shub_settings.num_ext_dev) break; id++; } diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_spi.c b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_spi.c index 67ff36eac247..eb1086e4a951 100644 --- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_spi.c +++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_spi.c @@ -12,7 +12,6 @@ #include <linux/module.h> #include <linux/spi/spi.h> #include <linux/slab.h> -#include <linux/of.h> #include <linux/regmap.h> #include "st_lsm6dsx.h" @@ -122,7 +121,7 @@ static struct spi_driver st_lsm6dsx_driver = { .driver = { .name = "st_lsm6dsx_spi", .pm = &st_lsm6dsx_pm_ops, - .of_match_table = of_match_ptr(st_lsm6dsx_spi_of_match), + .of_match_table = st_lsm6dsx_spi_of_match, }, .probe = st_lsm6dsx_spi_probe, .id_table = st_lsm6dsx_spi_id_table, diff --git a/drivers/iio/industrialio-buffer.c b/drivers/iio/industrialio-buffer.c index 112225c0e486..4ada5592aa2b 100644 --- a/drivers/iio/industrialio-buffer.c +++ b/drivers/iio/industrialio-buffer.c @@ -87,7 +87,7 @@ static bool iio_buffer_ready(struct iio_dev *indio_dev, struct iio_buffer *buf, } /** - * iio_buffer_read_first_n_outer() - chrdev read for buffer access + * iio_buffer_read_outer() - chrdev read for buffer access * @filp: File structure pointer for the char device * @buf: Destination buffer for iio buffer read * @n: First n bytes to read @@ -99,8 +99,8 @@ static bool iio_buffer_ready(struct iio_dev *indio_dev, struct iio_buffer *buf, * Return: negative values corresponding to error codes or ret != 0 * for ending the reading activity **/ -ssize_t iio_buffer_read_first_n_outer(struct file *filp, char __user *buf, - size_t n, loff_t *f_ps) +ssize_t iio_buffer_read_outer(struct file *filp, char __user *buf, + size_t n, loff_t *f_ps) { struct iio_dev *indio_dev = filp->private_data; struct iio_buffer *rb = indio_dev->buffer; @@ -112,7 +112,7 @@ ssize_t iio_buffer_read_first_n_outer(struct file *filp, char __user *buf, if (!indio_dev->info) return -ENODEV; - if (!rb || !rb->access->read_first_n) + if (!rb || !rb->access->read) return -EINVAL; datum_size = rb->bytes_per_datum; @@ -147,7 +147,7 @@ ssize_t iio_buffer_read_first_n_outer(struct file *filp, char __user *buf, continue; } - ret = rb->access->read_first_n(rb, n, buf); + ret = rb->access->read(rb, n, buf); if (ret == 0 && (filp->f_flags & O_NONBLOCK)) ret = -EAGAIN; } while (ret == 0); diff --git a/drivers/iio/industrialio-core.c b/drivers/iio/industrialio-core.c index a46cdf2d8833..65ff0d067018 100644 --- a/drivers/iio/industrialio-core.c +++ b/drivers/iio/industrialio-core.c @@ -161,6 +161,7 @@ static const char * const iio_chan_info_postfix[] = { [IIO_CHAN_INFO_DEBOUNCE_TIME] = "debounce_time", [IIO_CHAN_INFO_CALIBEMISSIVITY] = "calibemissivity", [IIO_CHAN_INFO_OVERSAMPLING_RATIO] = "oversampling_ratio", + [IIO_CHAN_INFO_THERMOCOUPLE_TYPE] = "thermocouple_type", }; /** @@ -596,6 +597,8 @@ static ssize_t __iio_format_value(char *buf, size_t len, unsigned int type, } return l; } + case IIO_VAL_CHAR: + return snprintf(buf, len, "%c", (char)vals[0]); default: return 0; } @@ -837,7 +840,8 @@ static ssize_t iio_write_channel_info(struct device *dev, struct iio_dev *indio_dev = dev_to_iio_dev(dev); struct iio_dev_attr *this_attr = to_iio_dev_attr(attr); int ret, fract_mult = 100000; - int integer, fract; + int integer, fract = 0; + bool is_char = false; /* Assumes decimal - precision based on number of digits */ if (!indio_dev->info->write_raw) @@ -855,13 +859,24 @@ static ssize_t iio_write_channel_info(struct device *dev, case IIO_VAL_INT_PLUS_NANO: fract_mult = 100000000; break; + case IIO_VAL_CHAR: + is_char = true; + break; default: return -EINVAL; } - ret = iio_str_to_fixpoint(buf, fract_mult, &integer, &fract); - if (ret) - return ret; + if (is_char) { + char ch; + + if (sscanf(buf, "%c", &ch) != 1) + return -EINVAL; + integer = ch; + } else { + ret = iio_str_to_fixpoint(buf, fract_mult, &integer, &fract); + if (ret) + return ret; + } ret = indio_dev->info->write_raw(indio_dev, this_attr->c, integer, fract, this_attr->address); @@ -1617,7 +1632,7 @@ static long iio_ioctl(struct file *filp, unsigned int cmd, unsigned long arg) } static const struct file_operations iio_buffer_fileops = { - .read = iio_buffer_read_first_n_outer_addr, + .read = iio_buffer_read_outer_addr, .release = iio_chrdev_release, .open = iio_chrdev_open, .poll = iio_buffer_poll_addr, diff --git a/drivers/iio/light/apds9960.c b/drivers/iio/light/apds9960.c index c5dfb9a6b5a1..52f86bc777dd 100644 --- a/drivers/iio/light/apds9960.c +++ b/drivers/iio/light/apds9960.c @@ -15,7 +15,6 @@ #include <linux/mutex.h> #include <linux/err.h> #include <linux/irq.h> -#include <linux/gpio.h> #include <linux/i2c.h> #include <linux/pm_runtime.h> #include <linux/regmap.h> @@ -24,7 +23,6 @@ #include <linux/iio/events.h> #include <linux/iio/kfifo_buf.h> #include <linux/iio/sysfs.h> -#include <linux/of_gpio.h> #define APDS9960_REGMAP_NAME "apds9960_regmap" #define APDS9960_DRV_NAME "apds9960" diff --git a/drivers/iio/light/lm3533-als.c b/drivers/iio/light/lm3533-als.c index 6733b52c22df..bc196c212881 100644 --- a/drivers/iio/light/lm3533-als.c +++ b/drivers/iio/light/lm3533-als.c @@ -742,7 +742,7 @@ static int lm3533_als_set_resistor(struct lm3533_als *als, u8 val) if (val < LM3533_ALS_RESISTOR_MIN || val > LM3533_ALS_RESISTOR_MAX) { dev_err(&als->pdev->dev, "invalid resistor value\n"); return -EINVAL; - }; + } ret = lm3533_write(als->lm3533, LM3533_REG_ALS_RESISTOR_SELECT, val); if (ret) { diff --git a/drivers/iio/light/si1145.c b/drivers/iio/light/si1145.c index 982bba0c54e7..0476c2bc8138 100644 --- a/drivers/iio/light/si1145.c +++ b/drivers/iio/light/si1145.c @@ -17,7 +17,6 @@ #include <linux/slab.h> #include <linux/delay.h> #include <linux/irq.h> -#include <linux/gpio.h> #include <linux/iio/iio.h> #include <linux/iio/sysfs.h> diff --git a/drivers/iio/light/st_uvis25_i2c.c b/drivers/iio/light/st_uvis25_i2c.c index dacbac6a6662..4889bbeb0c73 100644 --- a/drivers/iio/light/st_uvis25_i2c.c +++ b/drivers/iio/light/st_uvis25_i2c.c @@ -9,7 +9,6 @@ #include <linux/kernel.h> #include <linux/module.h> -#include <linux/acpi.h> #include <linux/i2c.h> #include <linux/slab.h> #include <linux/regmap.h> diff --git a/drivers/iio/magnetometer/ak8975.c b/drivers/iio/magnetometer/ak8975.c index 893bec5a0312..3c881541ae72 100644 --- a/drivers/iio/magnetometer/ak8975.c +++ b/drivers/iio/magnetometer/ak8975.c @@ -16,8 +16,7 @@ #include <linux/mutex.h> #include <linux/delay.h> #include <linux/bitops.h> -#include <linux/gpio.h> -#include <linux/of_gpio.h> +#include <linux/gpio/consumer.h> #include <linux/acpi.h> #include <linux/regulator/consumer.h> #include <linux/pm_runtime.h> @@ -29,8 +28,6 @@ #include <linux/iio/trigger_consumer.h> #include <linux/iio/triggered_buffer.h> -#include <linux/iio/magnetometer/ak8975.h> - /* * Register definitions, as well as various shifts and masks to get at the * individual fields of the registers. @@ -206,11 +203,11 @@ static long ak09912_raw_to_gauss(u16 data) /* Compatible Asahi Kasei Compass parts */ enum asahi_compass_chipset { + AKXXXX = 0, AK8975, AK8963, AK09911, AK09912, - AK_MAX_TYPE }; enum ak_ctrl_reg_addr { @@ -248,7 +245,7 @@ struct ak_def { u8 data_regs[3]; }; -static const struct ak_def ak_def_array[AK_MAX_TYPE] = { +static const struct ak_def ak_def_array[] = { { .type = AK8975, .raw_to_gauss = ak8975_raw_to_gauss, @@ -360,7 +357,7 @@ struct ak8975_data { struct mutex lock; u8 asa[3]; long raw_to_gauss[3]; - int eoc_gpio; + struct gpio_desc *eoc_gpiod; int eoc_irq; wait_queue_head_t data_ready_queue; unsigned long flags; @@ -498,15 +495,13 @@ static int ak8975_setup_irq(struct ak8975_data *data) if (client->irq) irq = client->irq; else - irq = gpio_to_irq(data->eoc_gpio); + irq = gpiod_to_irq(data->eoc_gpiod); rc = devm_request_irq(&client->dev, irq, ak8975_irq_handler, IRQF_TRIGGER_RISING | IRQF_ONESHOT, dev_name(&client->dev), data); if (rc < 0) { - dev_err(&client->dev, - "irq %d request failed, (gpio %d): %d\n", - irq, data->eoc_gpio, rc); + dev_err(&client->dev, "irq %d request failed: %d\n", irq, rc); return rc; } @@ -549,7 +544,7 @@ static int ak8975_setup(struct i2c_client *client) return ret; } - if (data->eoc_gpio > 0 || client->irq > 0) { + if (data->eoc_gpiod || client->irq > 0) { ret = ak8975_setup_irq(data); if (ret < 0) { dev_err(&client->dev, @@ -574,7 +569,7 @@ static int wait_conversion_complete_gpio(struct ak8975_data *data) /* Wait for the conversion to complete. */ while (timeout_ms) { msleep(AK8975_CONVERSION_DONE_POLL_TIME); - if (gpio_get_value(data->eoc_gpio)) + if (gpiod_get_value(data->eoc_gpiod)) break; timeout_ms -= AK8975_CONVERSION_DONE_POLL_TIME; } @@ -646,7 +641,7 @@ static int ak8975_start_read_axis(struct ak8975_data *data, /* Wait for the conversion to complete. */ if (data->eoc_irq) ret = wait_conversion_complete_interrupt(data); - else if (gpio_is_valid(data->eoc_gpio)) + else if (data->eoc_gpiod) ret = wait_conversion_complete_gpio(data); else ret = wait_conversion_complete_polled(data); @@ -786,19 +781,6 @@ static const struct acpi_device_id ak_acpi_match[] = { MODULE_DEVICE_TABLE(acpi, ak_acpi_match); #endif -static const char *ak8975_match_acpi_device(struct device *dev, - enum asahi_compass_chipset *chipset) -{ - const struct acpi_device_id *id; - - id = acpi_match_device(dev->driver->acpi_match_table, dev); - if (!id) - return NULL; - *chipset = (int)id->driver_data; - - return dev_name(dev); -} - static void ak8975_fill_buffer(struct iio_dev *indio_dev) { struct ak8975_data *data = iio_priv(indio_dev); @@ -856,36 +838,23 @@ static int ak8975_probe(struct i2c_client *client, { struct ak8975_data *data; struct iio_dev *indio_dev; - int eoc_gpio; + struct gpio_desc *eoc_gpiod; + const void *match; + unsigned int i; int err; + enum asahi_compass_chipset chipset; const char *name = NULL; - enum asahi_compass_chipset chipset = AK_MAX_TYPE; - const struct ak8975_platform_data *pdata = - dev_get_platdata(&client->dev); - - /* Grab and set up the supplied GPIO. */ - if (pdata) - eoc_gpio = pdata->eoc_gpio; - else if (client->dev.of_node) - eoc_gpio = of_get_gpio(client->dev.of_node, 0); - else - eoc_gpio = -1; - if (eoc_gpio == -EPROBE_DEFER) - return -EPROBE_DEFER; - - /* We may not have a GPIO based IRQ to scan, that is fine, we will - poll if so */ - if (gpio_is_valid(eoc_gpio)) { - err = devm_gpio_request_one(&client->dev, eoc_gpio, - GPIOF_IN, "ak_8975"); - if (err < 0) { - dev_err(&client->dev, - "failed to request GPIO %d, error %d\n", - eoc_gpio, err); - return err; - } - } + /* + * Grab and set up the supplied GPIO. + * We may not have a GPIO based IRQ to scan, that is fine, we will + * poll if so. + */ + eoc_gpiod = devm_gpiod_get_optional(&client->dev, NULL, GPIOD_IN); + if (IS_ERR(eoc_gpiod)) + return PTR_ERR(eoc_gpiod); + if (eoc_gpiod) + gpiod_set_consumer_name(eoc_gpiod, "ak_8975"); /* Register with IIO */ indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data)); @@ -896,35 +865,35 @@ static int ak8975_probe(struct i2c_client *client, i2c_set_clientdata(client, indio_dev); data->client = client; - data->eoc_gpio = eoc_gpio; + data->eoc_gpiod = eoc_gpiod; data->eoc_irq = 0; - if (!pdata) { - err = iio_read_mount_matrix(&client->dev, "mount-matrix", - &data->orientation); - if (err) - return err; - } else - data->orientation = pdata->orientation; + err = iio_read_mount_matrix(&client->dev, "mount-matrix", &data->orientation); + if (err) + return err; /* id will be NULL when enumerated via ACPI */ - if (id) { + match = device_get_match_data(&client->dev); + if (match) { + chipset = (enum asahi_compass_chipset)(match); + name = dev_name(&client->dev); + } else if (id) { chipset = (enum asahi_compass_chipset)(id->driver_data); name = id->name; - } else if (ACPI_HANDLE(&client->dev)) { - name = ak8975_match_acpi_device(&client->dev, &chipset); - if (!name) - return -ENODEV; } else return -ENOSYS; - if (chipset >= AK_MAX_TYPE) { + for (i = 0; i < ARRAY_SIZE(ak_def_array); i++) + if (ak_def_array[i].type == chipset) + break; + + if (i == ARRAY_SIZE(ak_def_array)) { dev_err(&client->dev, "AKM device type unsupported: %d\n", chipset); return -ENODEV; } - data->def = &ak_def_array[chipset]; + data->def = &ak_def_array[i]; /* Fetch the regulators */ data->vdd = devm_regulator_get(&client->dev, "vdd"); diff --git a/drivers/iio/magnetometer/st_magn_i2c.c b/drivers/iio/magnetometer/st_magn_i2c.c index fdba480a12be..c6bb4ce77594 100644 --- a/drivers/iio/magnetometer/st_magn_i2c.c +++ b/drivers/iio/magnetometer/st_magn_i2c.c @@ -17,7 +17,6 @@ #include <linux/iio/common/st_sensors_i2c.h> #include "st_magn.h" -#ifdef CONFIG_OF static const struct of_device_id st_magn_of_match[] = { { .compatible = "st,lsm303dlh-magn", @@ -50,9 +49,6 @@ static const struct of_device_id st_magn_of_match[] = { {}, }; MODULE_DEVICE_TABLE(of, st_magn_of_match); -#else -#define st_magn_of_match NULL -#endif static int st_magn_i2c_probe(struct i2c_client *client, const struct i2c_device_id *id) @@ -62,8 +58,7 @@ static int st_magn_i2c_probe(struct i2c_client *client, struct iio_dev *indio_dev; int err; - st_sensors_of_name_probe(&client->dev, st_magn_of_match, - client->name, sizeof(client->name)); + st_sensors_dev_name_probe(&client->dev, client->name, sizeof(client->name)); settings = st_magn_get_settings(client->name); if (!settings) { @@ -113,7 +108,7 @@ MODULE_DEVICE_TABLE(i2c, st_magn_id_table); static struct i2c_driver st_magn_driver = { .driver = { .name = "st-magn-i2c", - .of_match_table = of_match_ptr(st_magn_of_match), + .of_match_table = st_magn_of_match, }, .probe = st_magn_i2c_probe, .remove = st_magn_i2c_remove, diff --git a/drivers/iio/magnetometer/st_magn_spi.c b/drivers/iio/magnetometer/st_magn_spi.c index fbf909bde841..3d08d74c367d 100644 --- a/drivers/iio/magnetometer/st_magn_spi.c +++ b/drivers/iio/magnetometer/st_magn_spi.c @@ -17,7 +17,6 @@ #include <linux/iio/common/st_sensors_spi.h> #include "st_magn.h" -#ifdef CONFIG_OF /* * For new single-chip sensors use <device_name> as compatible string. * For old single-chip devices keep <device_name>-magn to maintain @@ -45,9 +44,6 @@ static const struct of_device_id st_magn_of_match[] = { {} }; MODULE_DEVICE_TABLE(of, st_magn_of_match); -#else -#define st_magn_of_match NULL -#endif static int st_magn_spi_probe(struct spi_device *spi) { @@ -56,8 +52,7 @@ static int st_magn_spi_probe(struct spi_device *spi) struct iio_dev *indio_dev; int err; - st_sensors_of_name_probe(&spi->dev, st_magn_of_match, - spi->modalias, sizeof(spi->modalias)); + st_sensors_dev_name_probe(&spi->dev, spi->modalias, sizeof(spi->modalias)); settings = st_magn_get_settings(spi->modalias); if (!settings) { @@ -104,7 +99,7 @@ MODULE_DEVICE_TABLE(spi, st_magn_id_table); static struct spi_driver st_magn_driver = { .driver = { .name = "st-magn-spi", - .of_match_table = of_match_ptr(st_magn_of_match), + .of_match_table = st_magn_of_match, }, .probe = st_magn_spi_probe, .remove = st_magn_spi_remove, diff --git a/drivers/iio/pressure/Kconfig b/drivers/iio/pressure/Kconfig index ba420e484787..9c2d9bf8f100 100644 --- a/drivers/iio/pressure/Kconfig +++ b/drivers/iio/pressure/Kconfig @@ -53,6 +53,18 @@ config IIO_CROS_EC_BARO To compile this driver as a module, choose M here: the module will be called cros_ec_baro. +config DLHL60D + tristate "All Sensors DLHL60D and DLHL60G low voltage digital pressure sensors" + depends on I2C + select IIO_BUFFER + select IIO_TRIGGERED_BUFFER + help + Say yes here to build support for the All Sensors DLH series + pressure sensors driver. + + To compile this driver as a module, choose M here: the module + will be called dlhl60d. + config DPS310 tristate "Infineon DPS310 pressure and temperature sensor" depends on I2C diff --git a/drivers/iio/pressure/Makefile b/drivers/iio/pressure/Makefile index d8f5ace1f25d..5a79192d8cb5 100644 --- a/drivers/iio/pressure/Makefile +++ b/drivers/iio/pressure/Makefile @@ -9,6 +9,7 @@ obj-$(CONFIG_BMP280) += bmp280.o bmp280-objs := bmp280-core.o bmp280-regmap.o obj-$(CONFIG_BMP280_I2C) += bmp280-i2c.o obj-$(CONFIG_BMP280_SPI) += bmp280-spi.o +obj-$(CONFIG_DLHL60D) += dlhl60d.o obj-$(CONFIG_DPS310) += dps310.o obj-$(CONFIG_IIO_CROS_EC_BARO) += cros_ec_baro.o obj-$(CONFIG_HID_SENSOR_PRESS) += hid-sensor-press.o diff --git a/drivers/iio/pressure/bmp280-i2c.c b/drivers/iio/pressure/bmp280-i2c.c index 3109c8e2cc11..8b03ea15c0d0 100644 --- a/drivers/iio/pressure/bmp280-i2c.c +++ b/drivers/iio/pressure/bmp280-i2c.c @@ -1,8 +1,6 @@ // SPDX-License-Identifier: GPL-2.0-only #include <linux/module.h> #include <linux/i2c.h> -#include <linux/acpi.h> -#include <linux/of.h> #include <linux/regmap.h> #include "bmp280.h" @@ -38,16 +36,6 @@ static int bmp280_i2c_probe(struct i2c_client *client, client->irq); } -static const struct acpi_device_id bmp280_acpi_i2c_match[] = { - {"BMP0280", BMP280_CHIP_ID }, - {"BMP0180", BMP180_CHIP_ID }, - {"BMP0085", BMP180_CHIP_ID }, - {"BME0280", BME280_CHIP_ID }, - { }, -}; -MODULE_DEVICE_TABLE(acpi, bmp280_acpi_i2c_match); - -#ifdef CONFIG_OF static const struct of_device_id bmp280_of_i2c_match[] = { { .compatible = "bosch,bme280", .data = (void *)BME280_CHIP_ID }, { .compatible = "bosch,bmp280", .data = (void *)BMP280_CHIP_ID }, @@ -56,9 +44,6 @@ static const struct of_device_id bmp280_of_i2c_match[] = { { }, }; MODULE_DEVICE_TABLE(of, bmp280_of_i2c_match); -#else -#define bmp280_of_i2c_match NULL -#endif static const struct i2c_device_id bmp280_i2c_id[] = { {"bmp280", BMP280_CHIP_ID }, @@ -72,8 +57,7 @@ MODULE_DEVICE_TABLE(i2c, bmp280_i2c_id); static struct i2c_driver bmp280_i2c_driver = { .driver = { .name = "bmp280", - .acpi_match_table = ACPI_PTR(bmp280_acpi_i2c_match), - .of_match_table = of_match_ptr(bmp280_of_i2c_match), + .of_match_table = bmp280_of_i2c_match, .pm = &bmp280_dev_pm_ops, }, .probe = bmp280_i2c_probe, diff --git a/drivers/iio/pressure/dlhl60d.c b/drivers/iio/pressure/dlhl60d.c new file mode 100644 index 000000000000..b8c99e7bd6cf --- /dev/null +++ b/drivers/iio/pressure/dlhl60d.c @@ -0,0 +1,375 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * All Sensors DLH series low voltage digital pressure sensors + * + * Copyright (c) 2019 AVL DiTEST GmbH + * Tomislav Denis <tomislav.denis@avl.com> + * + * Datasheet: http://www.allsensors.com/cad/DS-0355_Rev_B.PDF + */ + +#include <linux/module.h> +#include <linux/delay.h> +#include <linux/i2c.h> +#include <linux/iio/iio.h> +#include <linux/iio/buffer.h> +#include <linux/iio/trigger_consumer.h> +#include <linux/iio/triggered_buffer.h> +#include <asm/unaligned.h> + +/* Commands */ +#define DLH_START_SINGLE 0xAA + +/* Status bits */ +#define DLH_STATUS_OK 0x40 + +/* DLH data format */ +#define DLH_NUM_READ_BYTES 7 +#define DLH_NUM_DATA_BYTES 3 +#define DLH_NUM_PR_BITS 24 +#define DLH_NUM_TEMP_BITS 24 + +/* DLH timings */ +#define DLH_SINGLE_DUT_MS 5 + +enum dhl_ids { + dlhl60d, + dlhl60g, +}; + +struct dlh_info { + u8 osdig; /* digital offset factor */ + unsigned int fss; /* full scale span (inch H2O) */ +}; + +struct dlh_state { + struct i2c_client *client; + struct dlh_info info; + bool use_interrupt; + struct completion completion; + u8 rx_buf[DLH_NUM_READ_BYTES] ____cacheline_aligned; +}; + +static struct dlh_info dlh_info_tbl[] = { + [dlhl60d] = { + .osdig = 2, + .fss = 120, + }, + [dlhl60g] = { + .osdig = 10, + .fss = 60, + }, +}; + + +static int dlh_cmd_start_single(struct dlh_state *st) +{ + int ret; + + ret = i2c_smbus_write_byte(st->client, DLH_START_SINGLE); + if (ret) + dev_err(&st->client->dev, + "%s: I2C write byte failed\n", __func__); + + return ret; +} + +static int dlh_cmd_read_data(struct dlh_state *st) +{ + int ret; + + ret = i2c_master_recv(st->client, st->rx_buf, DLH_NUM_READ_BYTES); + if (ret < 0) { + dev_err(&st->client->dev, + "%s: I2C read block failed\n", __func__); + return ret; + } + + if (st->rx_buf[0] != DLH_STATUS_OK) { + dev_err(&st->client->dev, + "%s: invalid status 0x%02x\n", __func__, st->rx_buf[0]); + return -EBUSY; + } + + return 0; +} + +static int dlh_start_capture_and_read(struct dlh_state *st) +{ + int ret; + + if (st->use_interrupt) + reinit_completion(&st->completion); + + ret = dlh_cmd_start_single(st); + if (ret) + return ret; + + if (st->use_interrupt) { + ret = wait_for_completion_timeout(&st->completion, + msecs_to_jiffies(DLH_SINGLE_DUT_MS)); + if (!ret) { + dev_err(&st->client->dev, + "%s: conversion timed out\n", __func__); + return -ETIMEDOUT; + } + } else { + mdelay(DLH_SINGLE_DUT_MS); + } + + return dlh_cmd_read_data(st); +} + +static int dlh_read_direct(struct dlh_state *st, + unsigned int *pressure, unsigned int *temperature) +{ + int ret; + + ret = dlh_start_capture_and_read(st); + if (ret) + return ret; + + *pressure = get_unaligned_be32(&st->rx_buf[1]) >> 8; + *temperature = get_unaligned_be32(&st->rx_buf[3]) & + GENMASK(DLH_NUM_TEMP_BITS - 1, 0); + + return 0; +} + +static int dlh_read_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *channel, int *value, + int *value2, long mask) +{ + struct dlh_state *st = iio_priv(indio_dev); + unsigned int pressure, temperature; + int ret; + s64 tmp; + s32 rem; + + switch (mask) { + case IIO_CHAN_INFO_RAW: + ret = iio_device_claim_direct_mode(indio_dev); + if (ret) + return ret; + + ret = dlh_read_direct(st, &pressure, &temperature); + iio_device_release_direct_mode(indio_dev); + if (ret) + return ret; + + switch (channel->type) { + case IIO_PRESSURE: + *value = pressure; + return IIO_VAL_INT; + + case IIO_TEMP: + *value = temperature; + return IIO_VAL_INT; + + default: + return -EINVAL; + } + case IIO_CHAN_INFO_SCALE: + switch (channel->type) { + case IIO_PRESSURE: + tmp = div_s64(125LL * st->info.fss * 24909 * 100, + 1 << DLH_NUM_PR_BITS); + tmp = div_s64_rem(tmp, 1000000000LL, &rem); + *value = tmp; + *value2 = rem; + return IIO_VAL_INT_PLUS_NANO; + + case IIO_TEMP: + *value = 125 * 1000; + *value2 = DLH_NUM_TEMP_BITS; + return IIO_VAL_FRACTIONAL_LOG2; + + default: + return -EINVAL; + } + case IIO_CHAN_INFO_OFFSET: + switch (channel->type) { + case IIO_PRESSURE: + *value = -125 * st->info.fss * 24909; + *value2 = 100 * st->info.osdig * 100000; + return IIO_VAL_FRACTIONAL; + + case IIO_TEMP: + *value = -40 * 1000; + return IIO_VAL_INT; + + default: + return -EINVAL; + } + } + + return -EINVAL; +} + +static const struct iio_info dlh_info = { + .read_raw = dlh_read_raw, +}; + +static const struct iio_chan_spec dlh_channels[] = { + { + .type = IIO_PRESSURE, + .indexed = 1, + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), + .info_mask_shared_by_type = + BIT(IIO_CHAN_INFO_SCALE) | + BIT(IIO_CHAN_INFO_OFFSET), + .scan_index = 0, + .scan_type = { + .sign = 'u', + .realbits = DLH_NUM_PR_BITS, + .storagebits = 32, + .shift = 8, + .endianness = IIO_BE, + }, + }, { + .type = IIO_TEMP, + .indexed = 1, + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), + .info_mask_shared_by_type = + BIT(IIO_CHAN_INFO_SCALE) | + BIT(IIO_CHAN_INFO_OFFSET), + .scan_index = 1, + .scan_type = { + .sign = 'u', + .realbits = DLH_NUM_TEMP_BITS, + .storagebits = 32, + .shift = 8, + .endianness = IIO_BE, + }, + } +}; + +static irqreturn_t dlh_trigger_handler(int irq, void *private) +{ + struct iio_poll_func *pf = private; + struct iio_dev *indio_dev = pf->indio_dev; + struct dlh_state *st = iio_priv(indio_dev); + int ret; + unsigned int chn, i = 0; + __be32 tmp_buf[2]; + + ret = dlh_start_capture_and_read(st); + if (ret) + goto out; + + for_each_set_bit(chn, indio_dev->active_scan_mask, + indio_dev->masklength) { + memcpy(tmp_buf + i, + &st->rx_buf[1] + chn * DLH_NUM_DATA_BYTES, + DLH_NUM_DATA_BYTES); + i++; + } + + iio_push_to_buffers(indio_dev, tmp_buf); + +out: + iio_trigger_notify_done(indio_dev->trig); + + return IRQ_HANDLED; +} + +static irqreturn_t dlh_interrupt(int irq, void *private) +{ + struct iio_dev *indio_dev = private; + struct dlh_state *st = iio_priv(indio_dev); + + complete(&st->completion); + + return IRQ_HANDLED; +}; + +static int dlh_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct dlh_state *st; + struct iio_dev *indio_dev; + int ret; + + if (!i2c_check_functionality(client->adapter, + I2C_FUNC_I2C | I2C_FUNC_SMBUS_WRITE_BYTE)) { + dev_err(&client->dev, + "adapter doesn't support required i2c functionality\n"); + return -EOPNOTSUPP; + } + + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*st)); + if (!indio_dev) { + dev_err(&client->dev, "failed to allocate iio device\n"); + return -ENOMEM; + } + + i2c_set_clientdata(client, indio_dev); + + st = iio_priv(indio_dev); + st->info = dlh_info_tbl[id->driver_data]; + st->client = client; + st->use_interrupt = false; + + indio_dev->name = id->name; + indio_dev->dev.parent = &client->dev; + indio_dev->dev.of_node = client->dev.of_node; + indio_dev->info = &dlh_info; + indio_dev->modes = INDIO_DIRECT_MODE; + indio_dev->channels = dlh_channels; + indio_dev->num_channels = ARRAY_SIZE(dlh_channels); + + if (client->irq > 0) { + ret = devm_request_threaded_irq(&client->dev, client->irq, + dlh_interrupt, NULL, + IRQF_TRIGGER_RISING | IRQF_ONESHOT, + id->name, indio_dev); + if (ret) { + dev_err(&client->dev, "failed to allocate threaded irq"); + return ret; + } + + st->use_interrupt = true; + init_completion(&st->completion); + } + + ret = devm_iio_triggered_buffer_setup(&client->dev, indio_dev, + NULL, &dlh_trigger_handler, NULL); + if (ret) { + dev_err(&client->dev, "failed to setup iio buffer\n"); + return ret; + } + + ret = devm_iio_device_register(&client->dev, indio_dev); + if (ret) + dev_err(&client->dev, "failed to register iio device\n"); + + return ret; +} + +static const struct of_device_id dlh_of_match[] = { + { .compatible = "asc,dlhl60d" }, + { .compatible = "asc,dlhl60g" }, + {} +}; +MODULE_DEVICE_TABLE(of, dlh_of_match); + +static const struct i2c_device_id dlh_id[] = { + { "dlhl60d", dlhl60d }, + { "dlhl60g", dlhl60g }, + {} +}; +MODULE_DEVICE_TABLE(i2c, dlh_id); + +static struct i2c_driver dlh_driver = { + .driver = { + .name = "dlhl60d", + .of_match_table = dlh_of_match, + }, + .probe = dlh_probe, + .id_table = dlh_id, +}; +module_i2c_driver(dlh_driver); + +MODULE_AUTHOR("Tomislav Denis <tomislav.denis@avl.com>"); +MODULE_DESCRIPTION("Driver for All Sensors DLH series pressure sensors"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/iio/pressure/st_pressure.h b/drivers/iio/pressure/st_pressure.h index c2e47a6c3118..5c746ff6087e 100644 --- a/drivers/iio/pressure/st_pressure.h +++ b/drivers/iio/pressure/st_pressure.h @@ -37,7 +37,7 @@ enum st_press_type { * struct st_sensors_platform_data - default press platform data * @drdy_int_pin: default press DRDY is available on INT1 pin. */ -static const struct st_sensors_platform_data default_press_pdata = { +static __maybe_unused const struct st_sensors_platform_data default_press_pdata = { .drdy_int_pin = 1, }; diff --git a/drivers/iio/pressure/st_pressure_i2c.c b/drivers/iio/pressure/st_pressure_i2c.c index 71d2ed6b4948..09c6903f99b8 100644 --- a/drivers/iio/pressure/st_pressure_i2c.c +++ b/drivers/iio/pressure/st_pressure_i2c.c @@ -10,7 +10,6 @@ #include <linux/kernel.h> #include <linux/module.h> #include <linux/slab.h> -#include <linux/acpi.h> #include <linux/i2c.h> #include <linux/iio/iio.h> @@ -18,7 +17,6 @@ #include <linux/iio/common/st_sensors_i2c.h> #include "st_pressure.h" -#ifdef CONFIG_OF static const struct of_device_id st_press_of_match[] = { { .compatible = "st,lps001wp-press", @@ -51,9 +49,6 @@ static const struct of_device_id st_press_of_match[] = { {}, }; MODULE_DEVICE_TABLE(of, st_press_of_match); -#else -#define st_press_of_match NULL -#endif #ifdef CONFIG_ACPI static const struct acpi_device_id st_press_acpi_match[] = { @@ -61,8 +56,6 @@ static const struct acpi_device_id st_press_acpi_match[] = { { }, }; MODULE_DEVICE_TABLE(acpi, st_press_acpi_match); -#else -#define st_press_acpi_match NULL #endif static const struct i2c_device_id st_press_id_table[] = { @@ -85,18 +78,7 @@ static int st_press_i2c_probe(struct i2c_client *client, struct iio_dev *indio_dev; int ret; - if (client->dev.of_node) { - st_sensors_of_name_probe(&client->dev, st_press_of_match, - client->name, sizeof(client->name)); - } else if (ACPI_HANDLE(&client->dev)) { - ret = st_sensors_match_acpi_device(&client->dev); - if ((ret < 0) || (ret >= ST_PRESS_MAX)) - return -ENODEV; - - strlcpy(client->name, st_press_id_table[ret].name, - sizeof(client->name)); - } else if (!id) - return -ENODEV; + st_sensors_dev_name_probe(&client->dev, client->name, sizeof(client->name)); settings = st_press_get_settings(client->name); if (!settings) { @@ -133,7 +115,7 @@ static int st_press_i2c_remove(struct i2c_client *client) static struct i2c_driver st_press_driver = { .driver = { .name = "st-press-i2c", - .of_match_table = of_match_ptr(st_press_of_match), + .of_match_table = st_press_of_match, .acpi_match_table = ACPI_PTR(st_press_acpi_match), }, .probe = st_press_i2c_probe, diff --git a/drivers/iio/pressure/st_pressure_spi.c b/drivers/iio/pressure/st_pressure_spi.c index 7c8b70221e70..b5ee3ec2764f 100644 --- a/drivers/iio/pressure/st_pressure_spi.c +++ b/drivers/iio/pressure/st_pressure_spi.c @@ -17,7 +17,6 @@ #include <linux/iio/common/st_sensors_spi.h> #include "st_pressure.h" -#ifdef CONFIG_OF /* * For new single-chip sensors use <device_name> as compatible string. * For old single-chip devices keep <device_name>-press to maintain @@ -55,9 +54,6 @@ static const struct of_device_id st_press_of_match[] = { {}, }; MODULE_DEVICE_TABLE(of, st_press_of_match); -#else -#define st_press_of_match NULL -#endif static int st_press_spi_probe(struct spi_device *spi) { @@ -66,8 +62,7 @@ static int st_press_spi_probe(struct spi_device *spi) struct iio_dev *indio_dev; int err; - st_sensors_of_name_probe(&spi->dev, st_press_of_match, - spi->modalias, sizeof(spi->modalias)); + st_sensors_dev_name_probe(&spi->dev, spi->modalias, sizeof(spi->modalias)); settings = st_press_get_settings(spi->modalias); if (!settings) { @@ -116,7 +111,7 @@ MODULE_DEVICE_TABLE(spi, st_press_id_table); static struct spi_driver st_press_driver = { .driver = { .name = "st-press-spi", - .of_match_table = of_match_ptr(st_press_of_match), + .of_match_table = st_press_of_match, }, .probe = st_press_spi_probe, .remove = st_press_spi_remove, diff --git a/drivers/iio/proximity/Kconfig b/drivers/iio/proximity/Kconfig index d53601447da4..37606d400805 100644 --- a/drivers/iio/proximity/Kconfig +++ b/drivers/iio/proximity/Kconfig @@ -58,6 +58,21 @@ config MB1232 To compile this driver as a module, choose M here: the module will be called mb1232. +config PING + tristate "Parallax GPIO bitbanged ranger sensors" + depends on GPIOLIB + help + Say Y here to build a driver for GPIO bitbanged ranger sensors + with just one GPIO for the trigger and echo. This driver can be + used to measure the distance of objects. + + Actually supported are: + - Parallax PING))) (ultrasonic) + - Parallax LaserPING (time-of-flight) + + To compile this driver as a module, choose M here: the + module will be called ping. + config RFD77402 tristate "RFD77402 ToF sensor" depends on I2C diff --git a/drivers/iio/proximity/Makefile b/drivers/iio/proximity/Makefile index 0bb5f9de13d6..c591b019304e 100644 --- a/drivers/iio/proximity/Makefile +++ b/drivers/iio/proximity/Makefile @@ -8,6 +8,7 @@ obj-$(CONFIG_AS3935) += as3935.o obj-$(CONFIG_ISL29501) += isl29501.o obj-$(CONFIG_LIDAR_LITE_V2) += pulsedlight-lidar-lite-v2.o obj-$(CONFIG_MB1232) += mb1232.o +obj-$(CONFIG_PING) += ping.o obj-$(CONFIG_RFD77402) += rfd77402.o obj-$(CONFIG_SRF04) += srf04.o obj-$(CONFIG_SRF08) += srf08.o diff --git a/drivers/iio/proximity/as3935.c b/drivers/iio/proximity/as3935.c index b591c63bd6c4..bac9a433dd19 100644 --- a/drivers/iio/proximity/as3935.c +++ b/drivers/iio/proximity/as3935.c @@ -14,7 +14,6 @@ #include <linux/mutex.h> #include <linux/err.h> #include <linux/irq.h> -#include <linux/gpio.h> #include <linux/spi/spi.h> #include <linux/iio/iio.h> #include <linux/iio/sysfs.h> @@ -22,8 +21,6 @@ #include <linux/iio/trigger_consumer.h> #include <linux/iio/buffer.h> #include <linux/iio/triggered_buffer.h> -#include <linux/of_gpio.h> - #define AS3935_AFE_GAIN 0x00 #define AS3935_AFE_MASK 0x3F diff --git a/drivers/iio/proximity/ping.c b/drivers/iio/proximity/ping.c new file mode 100644 index 000000000000..34aff108dff5 --- /dev/null +++ b/drivers/iio/proximity/ping.c @@ -0,0 +1,335 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * PING: ultrasonic sensor for distance measuring by using only one GPIOs + * + * Copyright (c) 2019 Andreas Klinger <ak@it-klinger.de> + * + * For details about the devices see: + * http://parallax.com/sites/default/files/downloads/28041-LaserPING-2m-Rangefinder-Guide.pdf + * http://parallax.com/sites/default/files/downloads/28015-PING-Documentation-v1.6.pdf + * + * the measurement cycle as timing diagram looks like: + * + * GPIO ___ ________________________ + * ping: __/ \____________/ \________________ + * ^ ^ ^ ^ + * |<->| interrupt interrupt + * udelay(5) (ts_rising) (ts_falling) + * |<---------------------->| + * . pulse time measured . + * . --> one round trip of ultra sonic waves + * ultra . . + * sonic _ _ _. . + * burst: _________/ \_/ \_/ \_________________________________________ + * . + * ultra . + * sonic _ _ _. + * echo: __________________________________/ \_/ \_/ \________________ + */ +#include <linux/err.h> +#include <linux/gpio/consumer.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/platform_device.h> +#include <linux/property.h> +#include <linux/sched.h> +#include <linux/interrupt.h> +#include <linux/delay.h> +#include <linux/iio/iio.h> +#include <linux/iio/sysfs.h> + +struct ping_cfg { + unsigned long trigger_pulse_us; /* length of trigger pulse */ + int laserping_error; /* support error code in */ + /* pulse width of laser */ + /* ping sensors */ + s64 timeout_ns; /* timeout in ns */ +}; + +struct ping_data { + struct device *dev; + struct gpio_desc *gpiod_ping; + struct mutex lock; + int irqnr; + ktime_t ts_rising; + ktime_t ts_falling; + struct completion rising; + struct completion falling; + const struct ping_cfg *cfg; +}; + +static const struct ping_cfg pa_ping_cfg = { + .trigger_pulse_us = 5, + .laserping_error = 0, + .timeout_ns = 18500000, /* 3 meters */ +}; + +static const struct ping_cfg pa_laser_ping_cfg = { + .trigger_pulse_us = 5, + .laserping_error = 1, + .timeout_ns = 15500000, /* 2 meters plus error codes */ +}; + +static irqreturn_t ping_handle_irq(int irq, void *dev_id) +{ + struct iio_dev *indio_dev = dev_id; + struct ping_data *data = iio_priv(indio_dev); + ktime_t now = ktime_get(); + + if (gpiod_get_value(data->gpiod_ping)) { + data->ts_rising = now; + complete(&data->rising); + } else { + data->ts_falling = now; + complete(&data->falling); + } + + return IRQ_HANDLED; +} + +static int ping_read(struct ping_data *data) +{ + int ret; + ktime_t ktime_dt; + s64 dt_ns; + u32 time_ns, distance_mm; + struct platform_device *pdev = to_platform_device(data->dev); + struct iio_dev *indio_dev = iio_priv_to_dev(data); + + /* + * just one read-echo-cycle can take place at a time + * ==> lock against concurrent reading calls + */ + mutex_lock(&data->lock); + + reinit_completion(&data->rising); + reinit_completion(&data->falling); + + gpiod_set_value(data->gpiod_ping, 1); + udelay(data->cfg->trigger_pulse_us); + gpiod_set_value(data->gpiod_ping, 0); + + ret = gpiod_direction_input(data->gpiod_ping); + if (ret < 0) { + mutex_unlock(&data->lock); + return ret; + } + + data->irqnr = gpiod_to_irq(data->gpiod_ping); + if (data->irqnr < 0) { + dev_err(data->dev, "gpiod_to_irq: %d\n", data->irqnr); + mutex_unlock(&data->lock); + return data->irqnr; + } + + ret = request_irq(data->irqnr, ping_handle_irq, + IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, + pdev->name, indio_dev); + if (ret < 0) { + dev_err(data->dev, "request_irq: %d\n", ret); + mutex_unlock(&data->lock); + return ret; + } + + /* it should not take more than 20 ms until echo is rising */ + ret = wait_for_completion_killable_timeout(&data->rising, HZ/50); + if (ret < 0) + goto err_reset_direction; + else if (ret == 0) { + ret = -ETIMEDOUT; + goto err_reset_direction; + } + + /* it cannot take more than 50 ms until echo is falling */ + ret = wait_for_completion_killable_timeout(&data->falling, HZ/20); + if (ret < 0) + goto err_reset_direction; + else if (ret == 0) { + ret = -ETIMEDOUT; + goto err_reset_direction; + } + + ktime_dt = ktime_sub(data->ts_falling, data->ts_rising); + + free_irq(data->irqnr, indio_dev); + + ret = gpiod_direction_output(data->gpiod_ping, GPIOD_OUT_LOW); + if (ret < 0) { + mutex_unlock(&data->lock); + return ret; + } + + mutex_unlock(&data->lock); + + dt_ns = ktime_to_ns(ktime_dt); + if (dt_ns > data->cfg->timeout_ns) { + dev_dbg(data->dev, "distance out of range: dt=%lldns\n", + dt_ns); + return -EIO; + } + + time_ns = dt_ns; + + /* + * read error code of laser ping sensor and give users chance to + * figure out error by using dynamic debuggging + */ + if (data->cfg->laserping_error) { + if ((time_ns > 12500000) && (time_ns <= 13500000)) { + dev_dbg(data->dev, "target too close or to far\n"); + return -EIO; + } + if ((time_ns > 13500000) && (time_ns <= 14500000)) { + dev_dbg(data->dev, "internal sensor error\n"); + return -EIO; + } + if ((time_ns > 14500000) && (time_ns <= 15500000)) { + dev_dbg(data->dev, "internal sensor timeout\n"); + return -EIO; + } + } + + /* + * the speed as function of the temperature is approximately: + * + * speed = 331,5 + 0,6 * Temp + * with Temp in °C + * and speed in m/s + * + * use 343,5 m/s as ultrasonic speed at 20 °C here in absence of the + * temperature + * + * therefore: + * time 343,5 time * 232 + * distance = ------ * ------- = ------------ + * 10^6 2 1350800 + * with time in ns + * and distance in mm (one way) + * + * because we limit to 3 meters the multiplication with 232 just + * fits into 32 bit + */ + distance_mm = time_ns * 232 / 1350800; + + return distance_mm; + +err_reset_direction: + free_irq(data->irqnr, indio_dev); + mutex_unlock(&data->lock); + + if (gpiod_direction_output(data->gpiod_ping, GPIOD_OUT_LOW)) + dev_dbg(data->dev, "error in gpiod_direction_output\n"); + return ret; +} + +static int ping_read_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *channel, int *val, + int *val2, long info) +{ + struct ping_data *data = iio_priv(indio_dev); + int ret; + + if (channel->type != IIO_DISTANCE) + return -EINVAL; + + switch (info) { + case IIO_CHAN_INFO_RAW: + ret = ping_read(data); + if (ret < 0) + return ret; + *val = ret; + return IIO_VAL_INT; + case IIO_CHAN_INFO_SCALE: + /* + * maximum resolution in datasheet is 1 mm + * 1 LSB is 1 mm + */ + *val = 0; + *val2 = 1000; + return IIO_VAL_INT_PLUS_MICRO; + default: + return -EINVAL; + } +} + +static const struct iio_info ping_iio_info = { + .read_raw = ping_read_raw, +}; + +static const struct iio_chan_spec ping_chan_spec[] = { + { + .type = IIO_DISTANCE, + .info_mask_separate = + BIT(IIO_CHAN_INFO_RAW) | + BIT(IIO_CHAN_INFO_SCALE), + }, +}; + +static const struct of_device_id of_ping_match[] = { + { .compatible = "parallax,ping", .data = &pa_ping_cfg}, + { .compatible = "parallax,laserping", .data = &pa_ping_cfg}, + {}, +}; + +MODULE_DEVICE_TABLE(of, of_ping_match); + +static int ping_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct ping_data *data; + struct iio_dev *indio_dev; + + indio_dev = devm_iio_device_alloc(dev, sizeof(struct ping_data)); + if (!indio_dev) { + dev_err(dev, "failed to allocate IIO device\n"); + return -ENOMEM; + } + + data = iio_priv(indio_dev); + data->dev = dev; + data->cfg = of_device_get_match_data(dev); + + mutex_init(&data->lock); + init_completion(&data->rising); + init_completion(&data->falling); + + data->gpiod_ping = devm_gpiod_get(dev, "ping", GPIOD_OUT_LOW); + if (IS_ERR(data->gpiod_ping)) { + dev_err(dev, "failed to get ping-gpios: err=%ld\n", + PTR_ERR(data->gpiod_ping)); + return PTR_ERR(data->gpiod_ping); + } + + if (gpiod_cansleep(data->gpiod_ping)) { + dev_err(data->dev, "cansleep-GPIOs not supported\n"); + return -ENODEV; + } + + platform_set_drvdata(pdev, indio_dev); + + indio_dev->name = "ping"; + indio_dev->dev.parent = &pdev->dev; + indio_dev->info = &ping_iio_info; + indio_dev->modes = INDIO_DIRECT_MODE; + indio_dev->channels = ping_chan_spec; + indio_dev->num_channels = ARRAY_SIZE(ping_chan_spec); + + return devm_iio_device_register(dev, indio_dev); +} + +static struct platform_driver ping_driver = { + .probe = ping_probe, + .driver = { + .name = "ping-gpio", + .of_match_table = of_ping_match, + }, +}; + +module_platform_driver(ping_driver); + +MODULE_AUTHOR("Andreas Klinger <ak@it-klinger.de>"); +MODULE_DESCRIPTION("PING sensors for distance measuring using one GPIOs"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:ping"); diff --git a/drivers/iio/resolver/ad2s1200.c b/drivers/iio/resolver/ad2s1200.c index 17b89623418c..a391f46ee06b 100644 --- a/drivers/iio/resolver/ad2s1200.c +++ b/drivers/iio/resolver/ad2s1200.c @@ -10,7 +10,6 @@ #include <linux/bitops.h> #include <linux/delay.h> #include <linux/device.h> -#include <linux/gpio.h> #include <linux/gpio/consumer.h> #include <linux/module.h> #include <linux/mutex.h> diff --git a/drivers/iio/temperature/max31856.c b/drivers/iio/temperature/max31856.c index 73ed550e3fc9..b4cb21ab2e85 100644 --- a/drivers/iio/temperature/max31856.c +++ b/drivers/iio/temperature/max31856.c @@ -6,12 +6,14 @@ * Copyright (C) 2018-2019 Rockwell Collins */ +#include <linux/ctype.h> #include <linux/module.h> #include <linux/init.h> #include <linux/err.h> #include <linux/spi/spi.h> #include <linux/iio/iio.h> #include <linux/iio/sysfs.h> +#include <linux/util_macros.h> #include <dt-bindings/iio/temperature/thermocouple.h> /* * The MSB of the register value determines whether the following byte will @@ -23,6 +25,9 @@ #define MAX31856_CR0_1SHOT BIT(6) #define MAX31856_CR0_OCFAULT BIT(4) #define MAX31856_CR0_OCFAULT_MASK GENMASK(5, 4) +#define MAX31856_CR0_FILTER_50HZ BIT(0) +#define MAX31856_AVERAGING_MASK GENMASK(6, 4) +#define MAX31856_AVERAGING_SHIFT 4 #define MAX31856_TC_TYPE_MASK GENMASK(3, 0) #define MAX31856_FAULT_OVUV BIT(1) #define MAX31856_FAULT_OPEN BIT(0) @@ -49,7 +54,10 @@ static const struct iio_chan_spec max31856_channels[] = { { /* Thermocouple Temperature */ .type = IIO_TEMP, .info_mask_separate = - BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE), + BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE) | + BIT(IIO_CHAN_INFO_THERMOCOUPLE_TYPE), + .info_mask_shared_by_type = + BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO) }, { /* Cold Junction Temperature */ .type = IIO_TEMP, @@ -57,12 +65,20 @@ static const struct iio_chan_spec max31856_channels[] = { .modified = 1, .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE), + .info_mask_shared_by_type = + BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO) }, }; struct max31856_data { struct spi_device *spi; u32 thermocouple_type; + bool filter_50hz; + int averaging; +}; + +static const char max31856_tc_types[] = { + 'B', 'E', 'J', 'K', 'N', 'R', 'S', 'T' }; static int max31856_read(struct max31856_data *data, u8 reg, @@ -107,6 +123,10 @@ static int max31856_init(struct max31856_data *data) reg_cr1_val &= ~MAX31856_TC_TYPE_MASK; reg_cr1_val |= data->thermocouple_type; + + reg_cr1_val &= ~MAX31856_AVERAGING_MASK; + reg_cr1_val |= data->averaging << MAX31856_AVERAGING_SHIFT; + ret = max31856_write(data, MAX31856_CR1_REG, reg_cr1_val); if (ret) return ret; @@ -123,6 +143,11 @@ static int max31856_init(struct max31856_data *data) reg_cr0_val &= ~MAX31856_CR0_1SHOT; reg_cr0_val |= MAX31856_CR0_AUTOCONVERT; + if (data->filter_50hz) + reg_cr0_val |= MAX31856_CR0_FILTER_50HZ; + else + reg_cr0_val &= ~MAX31856_CR0_FILTER_50HZ; + return max31856_write(data, MAX31856_CR0_REG, reg_cr0_val); } @@ -210,6 +235,12 @@ static int max31856_read_raw(struct iio_dev *indio_dev, return IIO_VAL_INT_PLUS_MICRO; } break; + case IIO_CHAN_INFO_OVERSAMPLING_RATIO: + *val = 1 << data->averaging; + return IIO_VAL_INT; + case IIO_CHAN_INFO_THERMOCOUPLE_TYPE: + *val = max31856_tc_types[data->thermocouple_type]; + return IIO_VAL_CHAR; default: ret = -EINVAL; break; @@ -218,6 +249,62 @@ static int max31856_read_raw(struct iio_dev *indio_dev, return ret; } +static int max31856_write_raw_get_fmt(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + long mask) +{ + switch (mask) { + case IIO_CHAN_INFO_THERMOCOUPLE_TYPE: + return IIO_VAL_CHAR; + default: + return IIO_VAL_INT; + } +} + +static int max31856_write_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + int val, int val2, long mask) +{ + struct max31856_data *data = iio_priv(indio_dev); + int msb; + + switch (mask) { + case IIO_CHAN_INFO_OVERSAMPLING_RATIO: + if (val > 16 || val < 1) + return -EINVAL; + msb = fls(val) - 1; + /* Round up to next 2pow if needed */ + if (BIT(msb) < val) + msb++; + + data->averaging = msb; + max31856_init(data); + break; + case IIO_CHAN_INFO_THERMOCOUPLE_TYPE: + { + int tc_type = -1; + int i; + + for (i = 0; i < ARRAY_SIZE(max31856_tc_types); i++) { + if (max31856_tc_types[i] == toupper(val)) { + tc_type = i; + break; + } + } + if (tc_type < 0) + return -EINVAL; + + data->thermocouple_type = tc_type; + max31856_init(data); + break; + } + default: + return -EINVAL; + } + + return 0; +} + static ssize_t show_fault(struct device *dev, u8 faultbit, char *buf) { struct iio_dev *indio_dev = dev_to_iio_dev(dev); @@ -249,12 +336,54 @@ static ssize_t show_fault_oc(struct device *dev, return show_fault(dev, MAX31856_FAULT_OPEN, buf); } +static ssize_t show_filter(struct device *dev, + struct device_attribute *attr, + char *buf) +{ + struct iio_dev *indio_dev = dev_to_iio_dev(dev); + struct max31856_data *data = iio_priv(indio_dev); + + return sprintf(buf, "%d\n", data->filter_50hz ? 50 : 60); +} + +static ssize_t set_filter(struct device *dev, + struct device_attribute *attr, + const char *buf, + size_t len) +{ + struct iio_dev *indio_dev = dev_to_iio_dev(dev); + struct max31856_data *data = iio_priv(indio_dev); + unsigned int freq; + int ret; + + ret = kstrtouint(buf, 10, &freq); + if (ret) + return ret; + + switch (freq) { + case 50: + data->filter_50hz = true; + break; + case 60: + data->filter_50hz = false; + break; + default: + return -EINVAL; + } + + max31856_init(data); + return len; +} + static IIO_DEVICE_ATTR(fault_ovuv, 0444, show_fault_ovuv, NULL, 0); static IIO_DEVICE_ATTR(fault_oc, 0444, show_fault_oc, NULL, 0); +static IIO_DEVICE_ATTR(in_temp_filter_notch_center_frequency, 0644, + show_filter, set_filter, 0); static struct attribute *max31856_attributes[] = { &iio_dev_attr_fault_ovuv.dev_attr.attr, &iio_dev_attr_fault_oc.dev_attr.attr, + &iio_dev_attr_in_temp_filter_notch_center_frequency.dev_attr.attr, NULL, }; @@ -264,6 +393,8 @@ static const struct attribute_group max31856_group = { static const struct iio_info max31856_info = { .read_raw = max31856_read_raw, + .write_raw = max31856_write_raw, + .write_raw_get_fmt = max31856_write_raw_get_fmt, .attrs = &max31856_group, }; @@ -280,6 +411,7 @@ static int max31856_probe(struct spi_device *spi) data = iio_priv(indio_dev); data->spi = spi; + data->filter_50hz = false; spi_set_drvdata(spi, indio_dev); diff --git a/drivers/iio/temperature/maxim_thermocouple.c b/drivers/iio/temperature/maxim_thermocouple.c index d1360605209c..8d21116c7a22 100644 --- a/drivers/iio/temperature/maxim_thermocouple.c +++ b/drivers/iio/temperature/maxim_thermocouple.c @@ -14,6 +14,7 @@ #include <linux/of_device.h> #include <linux/spi/spi.h> #include <linux/iio/iio.h> +#include <linux/iio/sysfs.h> #include <linux/iio/trigger.h> #include <linux/iio/buffer.h> #include <linux/iio/triggered_buffer.h> @@ -24,13 +25,25 @@ enum { MAX6675, MAX31855, + MAX31855K, + MAX31855J, + MAX31855N, + MAX31855S, + MAX31855T, + MAX31855E, + MAX31855R, +}; + +static const char maxim_tc_types[] = { + 'K', '?', 'K', 'J', 'N', 'S', 'T', 'E', 'R' }; static const struct iio_chan_spec max6675_channels[] = { { /* thermocouple temperature */ .type = IIO_TEMP, .info_mask_separate = - BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE), + BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE) | + BIT(IIO_CHAN_INFO_THERMOCOUPLE_TYPE), .scan_index = 0, .scan_type = { .sign = 's', @@ -48,7 +61,8 @@ static const struct iio_chan_spec max31855_channels[] = { .type = IIO_TEMP, .address = 2, .info_mask_separate = - BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE), + BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE) | + BIT(IIO_CHAN_INFO_THERMOCOUPLE_TYPE), .scan_index = 0, .scan_type = { .sign = 's', @@ -110,6 +124,7 @@ struct maxim_thermocouple_data { const struct maxim_thermocouple_chip *chip; u8 buffer[16] ____cacheline_aligned; + char tc_type; }; static int maxim_thermocouple_read(struct maxim_thermocouple_data *data, @@ -196,6 +211,10 @@ static int maxim_thermocouple_read_raw(struct iio_dev *indio_dev, ret = IIO_VAL_INT; } break; + case IIO_CHAN_INFO_THERMOCOUPLE_TYPE: + *val = data->tc_type; + ret = IIO_VAL_CHAR; + break; } return ret; @@ -210,8 +229,9 @@ static int maxim_thermocouple_probe(struct spi_device *spi) const struct spi_device_id *id = spi_get_device_id(spi); struct iio_dev *indio_dev; struct maxim_thermocouple_data *data; + const int chip_type = (id->driver_data == MAX6675) ? MAX6675 : MAX31855; const struct maxim_thermocouple_chip *chip = - &maxim_thermocouple_chips[id->driver_data]; + &maxim_thermocouple_chips[chip_type]; int ret; indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*data)); @@ -229,6 +249,7 @@ static int maxim_thermocouple_probe(struct spi_device *spi) data = iio_priv(indio_dev); data->spi = spi; data->chip = chip; + data->tc_type = maxim_tc_types[id->driver_data]; ret = devm_iio_triggered_buffer_setup(&spi->dev, indio_dev, NULL, @@ -236,12 +257,22 @@ static int maxim_thermocouple_probe(struct spi_device *spi) if (ret) return ret; + if (id->driver_data == MAX31855) + dev_warn(&spi->dev, "generic max31855 ID is deprecated\nplease use more specific part type"); + return devm_iio_device_register(&spi->dev, indio_dev); } static const struct spi_device_id maxim_thermocouple_id[] = { {"max6675", MAX6675}, {"max31855", MAX31855}, + {"max31855k", MAX31855K}, + {"max31855j", MAX31855J}, + {"max31855n", MAX31855N}, + {"max31855s", MAX31855S}, + {"max31855t", MAX31855T}, + {"max31855e", MAX31855E}, + {"max31855r", MAX31855R}, {}, }; MODULE_DEVICE_TABLE(spi, maxim_thermocouple_id); @@ -249,6 +280,13 @@ MODULE_DEVICE_TABLE(spi, maxim_thermocouple_id); static const struct of_device_id maxim_thermocouple_of_match[] = { { .compatible = "maxim,max6675" }, { .compatible = "maxim,max31855" }, + { .compatible = "maxim,max31855k" }, + { .compatible = "maxim,max31855j" }, + { .compatible = "maxim,max31855n" }, + { .compatible = "maxim,max31855s" }, + { .compatible = "maxim,max31855t" }, + { .compatible = "maxim,max31855e" }, + { .compatible = "maxim,max31855r" }, { }, }; MODULE_DEVICE_TABLE(of, maxim_thermocouple_of_match); diff --git a/drivers/iio/trigger/stm32-timer-trigger.c b/drivers/iio/trigger/stm32-timer-trigger.c index a5dfe65cd9b9..2e0d32aa8436 100644 --- a/drivers/iio/trigger/stm32-timer-trigger.c +++ b/drivers/iio/trigger/stm32-timer-trigger.c @@ -297,9 +297,6 @@ static ssize_t stm32_tt_store_master_mode(struct device *dev, strlen(master_mode_table[i]))) { regmap_update_bits(priv->regmap, TIM_CR2, mask, i << shift); - /* Make sure that registers are updated */ - regmap_update_bits(priv->regmap, TIM_EGR, - TIM_EGR_UG, TIM_EGR_UG); return len; } } diff --git a/drivers/isdn/Makefile b/drivers/isdn/Makefile index 63baf27a2c79..d14334f4007e 100644 --- a/drivers/isdn/Makefile +++ b/drivers/isdn/Makefile @@ -3,6 +3,6 @@ # Object files in subdirectories -obj-$(CONFIG_ISDN_CAPI) += capi/ +obj-$(CONFIG_BT_CMTP) += capi/ obj-$(CONFIG_MISDN) += mISDN/ obj-$(CONFIG_ISDN) += hardware/ diff --git a/drivers/isdn/capi/Kconfig b/drivers/isdn/capi/Kconfig index 573fea5500ce..cc408ad9aafb 100644 --- a/drivers/isdn/capi/Kconfig +++ b/drivers/isdn/capi/Kconfig @@ -1,6 +1,6 @@ # SPDX-License-Identifier: GPL-2.0-only -menuconfig ISDN_CAPI - tristate "CAPI 2.0 subsystem" +config ISDN_CAPI + def_bool ISDN && BT help This provides CAPI (the Common ISDN Application Programming Interface) Version 2.0, a standard making it easy for programs to @@ -15,42 +15,18 @@ menuconfig ISDN_CAPI See CONFIG_BT_CMTP for the last remaining regular driver in the kernel that uses the CAPI subsystem. -if ISDN_CAPI - config CAPI_TRACE - bool "CAPI trace support" - default y + def_bool BT_CMTP help If you say Y here, the kernelcapi driver can make verbose traces of CAPI messages. This feature can be enabled/disabled via IOCTL for every controller (default disabled). - This will increase the size of the kernelcapi module by 20 KB. - If unsure, say Y. - -config ISDN_CAPI_CAPI20 - tristate "CAPI2.0 /dev/capi20 support" - help - This option will provide the CAPI 2.0 interface to userspace - applications via /dev/capi20. Applications should use the - standardized libcapi20 to access this functionality. You should say - Y/M here. config ISDN_CAPI_MIDDLEWARE - bool "CAPI2.0 Middleware support" - depends on ISDN_CAPI_CAPI20 && TTY + def_bool BT_CMTP && TTY help This option will enhance the capabilities of the /dev/capi20 interface. It will provide a means of moving a data connection, established via the usual /dev/capi20 interface to a special tty device. If you want to use pppd with pppdcapiplugin to dial up to your ISP, say Y here. - -config ISDN_CAPI_CAPIDRV_VERBOSE - bool "Verbose reason code reporting" - depends on ISDN_CAPI_CAPIDRV - help - If you say Y here, the capidrv interface will give verbose reasons - for disconnecting. This will increase the size of the kernel by 7 KB. - If unsure, say N. - -endif diff --git a/drivers/isdn/capi/Makefile b/drivers/isdn/capi/Makefile index d299f3e75f89..352217ebabd8 100644 --- a/drivers/isdn/capi/Makefile +++ b/drivers/isdn/capi/Makefile @@ -1,17 +1,5 @@ # SPDX-License-Identifier: GPL-2.0 -# Makefile for the CAPI subsystem. +# Makefile for the CAPI subsystem used by BT_CMTP -# Ordering constraints: kernelcapi.o first - -# Each configuration option enables a list of files. - -obj-$(CONFIG_ISDN_CAPI) += kernelcapi.o -obj-$(CONFIG_ISDN_CAPI_CAPI20) += capi.o -obj-$(CONFIG_ISDN_CAPI_CAPIDRV) += capidrv.o - -# Multipart objects. - -kernelcapi-y := kcapi.o capiutil.o capilib.o -kernelcapi-$(CONFIG_PROC_FS) += kcapi_proc.o - -ccflags-y += -I$(srctree)/$(src)/../include -I$(srctree)/$(src)/../include/uapi +obj-$(CONFIG_BT_CMTP) += kernelcapi.o +kernelcapi-y := kcapi.o capiutil.o capi.o kcapi_proc.o diff --git a/drivers/isdn/capi/capi.c b/drivers/isdn/capi/capi.c index 1675da34239b..85767f52fe3c 100644 --- a/drivers/isdn/capi/capi.c +++ b/drivers/isdn/capi/capi.c @@ -39,7 +39,9 @@ #include <linux/isdn/capiutil.h> #include <linux/isdn/capicmd.h> -MODULE_DESCRIPTION("CAPI4Linux: Userspace /dev/capi20 interface"); +#include "kcapi.h" + +MODULE_DESCRIPTION("CAPI4Linux: kernel CAPI layer and /dev/capi20 interface"); MODULE_AUTHOR("Carsten Paeth"); MODULE_LICENSE("GPL"); @@ -1412,15 +1414,22 @@ static int __init capi_init(void) { const char *compileinfo; int major_ret; + int ret; + + ret = kcapi_init(); + if (ret) + return ret; major_ret = register_chrdev(capi_major, "capi20", &capi_fops); if (major_ret < 0) { printk(KERN_ERR "capi20: unable to get major %d\n", capi_major); + kcapi_exit(); return major_ret; } capi_class = class_create(THIS_MODULE, "capi"); if (IS_ERR(capi_class)) { unregister_chrdev(capi_major, "capi20"); + kcapi_exit(); return PTR_ERR(capi_class); } @@ -1430,6 +1439,7 @@ static int __init capi_init(void) device_destroy(capi_class, MKDEV(capi_major, 0)); class_destroy(capi_class); unregister_chrdev(capi_major, "capi20"); + kcapi_exit(); return -ENOMEM; } @@ -1455,6 +1465,8 @@ static void __exit capi_exit(void) unregister_chrdev(capi_major, "capi20"); capinc_tty_exit(); + + kcapi_exit(); } module_init(capi_init); diff --git a/drivers/isdn/capi/capilib.c b/drivers/isdn/capi/capilib.c deleted file mode 100644 index a39ad3796bba..000000000000 --- a/drivers/isdn/capi/capilib.c +++ /dev/null @@ -1,202 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 - -#include <linux/slab.h> -#include <linux/kernel.h> -#include <linux/module.h> -#include <linux/isdn/capilli.h> - -#define DBG(format, arg...) do { \ - printk(KERN_DEBUG "%s: " format "\n" , __func__ , ## arg); \ - } while (0) - -struct capilib_msgidqueue { - struct capilib_msgidqueue *next; - u16 msgid; -}; - -struct capilib_ncci { - struct list_head list; - u16 applid; - u32 ncci; - u32 winsize; - int nmsg; - struct capilib_msgidqueue *msgidqueue; - struct capilib_msgidqueue *msgidlast; - struct capilib_msgidqueue *msgidfree; - struct capilib_msgidqueue msgidpool[CAPI_MAXDATAWINDOW]; -}; - -// --------------------------------------------------------------------------- -// NCCI Handling - -static inline void mq_init(struct capilib_ncci *np) -{ - u_int i; - np->msgidqueue = NULL; - np->msgidlast = NULL; - np->nmsg = 0; - memset(np->msgidpool, 0, sizeof(np->msgidpool)); - np->msgidfree = &np->msgidpool[0]; - for (i = 1; i < np->winsize; i++) { - np->msgidpool[i].next = np->msgidfree; - np->msgidfree = &np->msgidpool[i]; - } -} - -static inline int mq_enqueue(struct capilib_ncci *np, u16 msgid) -{ - struct capilib_msgidqueue *mq; - if ((mq = np->msgidfree) == NULL) - return 0; - np->msgidfree = mq->next; - mq->msgid = msgid; - mq->next = NULL; - if (np->msgidlast) - np->msgidlast->next = mq; - np->msgidlast = mq; - if (!np->msgidqueue) - np->msgidqueue = mq; - np->nmsg++; - return 1; -} - -static inline int mq_dequeue(struct capilib_ncci *np, u16 msgid) -{ - struct capilib_msgidqueue **pp; - for (pp = &np->msgidqueue; *pp; pp = &(*pp)->next) { - if ((*pp)->msgid == msgid) { - struct capilib_msgidqueue *mq = *pp; - *pp = mq->next; - if (mq == np->msgidlast) - np->msgidlast = NULL; - mq->next = np->msgidfree; - np->msgidfree = mq; - np->nmsg--; - return 1; - } - } - return 0; -} - -void capilib_new_ncci(struct list_head *head, u16 applid, u32 ncci, u32 winsize) -{ - struct capilib_ncci *np; - - np = kmalloc(sizeof(*np), GFP_ATOMIC); - if (!np) { - printk(KERN_WARNING "capilib_new_ncci: no memory.\n"); - return; - } - if (winsize > CAPI_MAXDATAWINDOW) { - printk(KERN_ERR "capi_new_ncci: winsize %d too big\n", - winsize); - winsize = CAPI_MAXDATAWINDOW; - } - np->applid = applid; - np->ncci = ncci; - np->winsize = winsize; - mq_init(np); - list_add_tail(&np->list, head); - DBG("kcapi: appl %d ncci 0x%x up", applid, ncci); -} - -EXPORT_SYMBOL(capilib_new_ncci); - -void capilib_free_ncci(struct list_head *head, u16 applid, u32 ncci) -{ - struct list_head *l; - struct capilib_ncci *np; - - list_for_each(l, head) { - np = list_entry(l, struct capilib_ncci, list); - if (np->applid != applid) - continue; - if (np->ncci != ncci) - continue; - printk(KERN_INFO "kcapi: appl %d ncci 0x%x down\n", applid, ncci); - list_del(&np->list); - kfree(np); - return; - } - printk(KERN_ERR "capilib_free_ncci: ncci 0x%x not found\n", ncci); -} - -EXPORT_SYMBOL(capilib_free_ncci); - -void capilib_release_appl(struct list_head *head, u16 applid) -{ - struct list_head *l, *n; - struct capilib_ncci *np; - - list_for_each_safe(l, n, head) { - np = list_entry(l, struct capilib_ncci, list); - if (np->applid != applid) - continue; - printk(KERN_INFO "kcapi: appl %d ncci 0x%x forced down\n", applid, np->ncci); - list_del(&np->list); - kfree(np); - } -} - -EXPORT_SYMBOL(capilib_release_appl); - -void capilib_release(struct list_head *head) -{ - struct list_head *l, *n; - struct capilib_ncci *np; - - list_for_each_safe(l, n, head) { - np = list_entry(l, struct capilib_ncci, list); - printk(KERN_INFO "kcapi: appl %d ncci 0x%x forced down\n", np->applid, np->ncci); - list_del(&np->list); - kfree(np); - } -} - -EXPORT_SYMBOL(capilib_release); - -u16 capilib_data_b3_req(struct list_head *head, u16 applid, u32 ncci, u16 msgid) -{ - struct list_head *l; - struct capilib_ncci *np; - - list_for_each(l, head) { - np = list_entry(l, struct capilib_ncci, list); - if (np->applid != applid) - continue; - if (np->ncci != ncci) - continue; - - if (mq_enqueue(np, msgid) == 0) - return CAPI_SENDQUEUEFULL; - - return CAPI_NOERROR; - } - printk(KERN_ERR "capilib_data_b3_req: ncci 0x%x not found\n", ncci); - return CAPI_NOERROR; -} - -EXPORT_SYMBOL(capilib_data_b3_req); - -void capilib_data_b3_conf(struct list_head *head, u16 applid, u32 ncci, u16 msgid) -{ - struct list_head *l; - struct capilib_ncci *np; - - list_for_each(l, head) { - np = list_entry(l, struct capilib_ncci, list); - if (np->applid != applid) - continue; - if (np->ncci != ncci) - continue; - - if (mq_dequeue(np, msgid) == 0) { - printk(KERN_ERR "kcapi: msgid %hu ncci 0x%x not on queue\n", - msgid, ncci); - } - return; - } - printk(KERN_ERR "capilib_data_b3_conf: ncci 0x%x not found\n", ncci); -} - -EXPORT_SYMBOL(capilib_data_b3_conf); diff --git a/drivers/isdn/capi/capiutil.c b/drivers/isdn/capi/capiutil.c index 9846d82eb097..f26bf3c66d7e 100644 --- a/drivers/isdn/capi/capiutil.c +++ b/drivers/isdn/capi/capiutil.c @@ -20,6 +20,8 @@ #include <linux/isdn/capiutil.h> #include <linux/slab.h> +#include "kcapi.h" + /* from CAPI2.0 DDK AVM Berlin GmbH */ typedef struct { @@ -245,190 +247,6 @@ static void jumpcstruct(_cmsg *cmsg) } } } -/*-------------------------------------------------------*/ -static void pars_2_message(_cmsg *cmsg) -{ - - for (; TYP != _CEND; cmsg->p++) { - switch (TYP) { - case _CBYTE: - byteTLcpy(cmsg->m + cmsg->l, OFF); - cmsg->l++; - break; - case _CWORD: - wordTLcpy(cmsg->m + cmsg->l, OFF); - cmsg->l += 2; - break; - case _CDWORD: - dwordTLcpy(cmsg->m + cmsg->l, OFF); - cmsg->l += 4; - break; - case _CSTRUCT: - if (*(u8 **) OFF == NULL) { - *(cmsg->m + cmsg->l) = '\0'; - cmsg->l++; - } else if (**(_cstruct *) OFF != 0xff) { - structTLcpy(cmsg->m + cmsg->l, *(_cstruct *) OFF, 1 + **(_cstruct *) OFF); - cmsg->l += 1 + **(_cstruct *) OFF; - } else { - _cstruct s = *(_cstruct *) OFF; - structTLcpy(cmsg->m + cmsg->l, s, 3 + *(u16 *) (s + 1)); - cmsg->l += 3 + *(u16 *) (s + 1); - } - break; - case _CMSTRUCT: -/*----- Metastruktur 0 -----*/ - if (*(_cmstruct *) OFF == CAPI_DEFAULT) { - *(cmsg->m + cmsg->l) = '\0'; - cmsg->l++; - jumpcstruct(cmsg); - } -/*----- Metastruktur wird composed -----*/ - else { - unsigned _l = cmsg->l; - unsigned _ls; - cmsg->l++; - cmsg->p++; - pars_2_message(cmsg); - _ls = cmsg->l - _l - 1; - if (_ls < 255) - (cmsg->m + _l)[0] = (u8) _ls; - else { - structTLcpyovl(cmsg->m + _l + 3, cmsg->m + _l + 1, _ls); - (cmsg->m + _l)[0] = 0xff; - wordTLcpy(cmsg->m + _l + 1, &_ls); - } - } - break; - } - } -} - -/** - * capi_cmsg2message() - assemble CAPI 2.0 message from _cmsg structure - * @cmsg: _cmsg structure - * @msg: buffer for assembled message - * - * Return value: 0 for success - */ - -unsigned capi_cmsg2message(_cmsg *cmsg, u8 *msg) -{ - cmsg->m = msg; - cmsg->l = 8; - cmsg->p = 0; - cmsg->par = capi_cmd2par(cmsg->Command, cmsg->Subcommand); - if (!cmsg->par) - return 1; /* invalid command/subcommand */ - - pars_2_message(cmsg); - - wordTLcpy(msg + 0, &cmsg->l); - byteTLcpy(cmsg->m + 4, &cmsg->Command); - byteTLcpy(cmsg->m + 5, &cmsg->Subcommand); - wordTLcpy(cmsg->m + 2, &cmsg->ApplId); - wordTLcpy(cmsg->m + 6, &cmsg->Messagenumber); - - return 0; -} - -/*-------------------------------------------------------*/ -static void message_2_pars(_cmsg *cmsg) -{ - for (; TYP != _CEND; cmsg->p++) { - - switch (TYP) { - case _CBYTE: - byteTRcpy(cmsg->m + cmsg->l, OFF); - cmsg->l++; - break; - case _CWORD: - wordTRcpy(cmsg->m + cmsg->l, OFF); - cmsg->l += 2; - break; - case _CDWORD: - dwordTRcpy(cmsg->m + cmsg->l, OFF); - cmsg->l += 4; - break; - case _CSTRUCT: - *(u8 **) OFF = cmsg->m + cmsg->l; - - if (cmsg->m[cmsg->l] != 0xff) - cmsg->l += 1 + cmsg->m[cmsg->l]; - else - cmsg->l += 3 + *(u16 *) (cmsg->m + cmsg->l + 1); - break; - case _CMSTRUCT: -/*----- Metastruktur 0 -----*/ - if (cmsg->m[cmsg->l] == '\0') { - *(_cmstruct *) OFF = CAPI_DEFAULT; - cmsg->l++; - jumpcstruct(cmsg); - } else { - unsigned _l = cmsg->l; - *(_cmstruct *) OFF = CAPI_COMPOSE; - cmsg->l = (cmsg->m + _l)[0] == 255 ? cmsg->l + 3 : cmsg->l + 1; - cmsg->p++; - message_2_pars(cmsg); - } - break; - } - } -} - -/** - * capi_message2cmsg() - disassemble CAPI 2.0 message into _cmsg structure - * @cmsg: _cmsg structure - * @msg: buffer for assembled message - * - * Return value: 0 for success - */ - -unsigned capi_message2cmsg(_cmsg *cmsg, u8 *msg) -{ - memset(cmsg, 0, sizeof(_cmsg)); - cmsg->m = msg; - cmsg->l = 8; - cmsg->p = 0; - byteTRcpy(cmsg->m + 4, &cmsg->Command); - byteTRcpy(cmsg->m + 5, &cmsg->Subcommand); - cmsg->par = capi_cmd2par(cmsg->Command, cmsg->Subcommand); - if (!cmsg->par) - return 1; /* invalid command/subcommand */ - - message_2_pars(cmsg); - - wordTRcpy(msg + 0, &cmsg->l); - wordTRcpy(cmsg->m + 2, &cmsg->ApplId); - wordTRcpy(cmsg->m + 6, &cmsg->Messagenumber); - - return 0; -} - -/** - * capi_cmsg_header() - initialize header part of _cmsg structure - * @cmsg: _cmsg structure - * @_ApplId: ApplID field value - * @_Command: Command field value - * @_Subcommand: Subcommand field value - * @_Messagenumber: Message Number field value - * @_Controller: Controller/PLCI/NCCI field value - * - * Return value: 0 for success - */ - -unsigned capi_cmsg_header(_cmsg *cmsg, u16 _ApplId, - u8 _Command, u8 _Subcommand, - u16 _Messagenumber, u32 _Controller) -{ - memset(cmsg, 0, sizeof(_cmsg)); - cmsg->ApplId = _ApplId; - cmsg->Command = _Command; - cmsg->Subcommand = _Subcommand; - cmsg->Messagenumber = _Messagenumber; - cmsg->adr.adrController = _Controller; - return 0; -} /*-------------------------------------------------------*/ @@ -561,8 +379,6 @@ static char *pnames[] = /*2f */ "Useruserdata" }; - - #include <stdarg.h> /*-------------------------------------------------------*/ @@ -800,37 +616,6 @@ _cdebbuf *capi_message2str(u8 *msg) return cdb; } -/** - * capi_cmsg2str() - format _cmsg structure for printing - * @cmsg: _cmsg structure - * - * Allocates a CAPI debug buffer and fills it with a printable representation - * of the CAPI 2.0 message stored in @cmsg by a previous call to - * capi_cmsg2message() or capi_message2cmsg(). - * Return value: allocated debug buffer, NULL on error - * The returned buffer should be freed by a call to cdebbuf_free() after use. - */ - -_cdebbuf *capi_cmsg2str(_cmsg *cmsg) -{ - _cdebbuf *cdb; - - if (!cmsg->m) - return NULL; /* no message */ - cdb = cdebbuf_alloc(); - if (!cdb) - return NULL; - cmsg->l = 8; - cmsg->p = 0; - cdb = bufprint(cdb, "%s ID=%03d #0x%04x LEN=%04d\n", - capi_cmd2str(cmsg->Command, cmsg->Subcommand), - ((u16 *) cmsg->m)[1], - ((u16 *) cmsg->m)[3], - ((u16 *) cmsg->m)[0]); - cdb = protocol_message_2_pars(cdb, cmsg, 1); - return cdb; -} - int __init cdebug_init(void) { g_cmsg = kmalloc(sizeof(_cmsg), GFP_KERNEL); @@ -854,7 +639,7 @@ int __init cdebug_init(void) return 0; } -void __exit cdebug_exit(void) +void cdebug_exit(void) { if (g_debbuf) kfree(g_debbuf->buf); @@ -885,16 +670,8 @@ int __init cdebug_init(void) return 0; } -void __exit cdebug_exit(void) +void cdebug_exit(void) { } #endif - -EXPORT_SYMBOL(cdebbuf_free); -EXPORT_SYMBOL(capi_cmsg2message); -EXPORT_SYMBOL(capi_message2cmsg); -EXPORT_SYMBOL(capi_cmsg_header); -EXPORT_SYMBOL(capi_cmd2str); -EXPORT_SYMBOL(capi_cmsg2str); -EXPORT_SYMBOL(capi_message2str); diff --git a/drivers/isdn/capi/kcapi.c b/drivers/isdn/capi/kcapi.c index a4ceb61c5b60..7168778fbbe1 100644 --- a/drivers/isdn/capi/kcapi.c +++ b/drivers/isdn/capi/kcapi.c @@ -10,8 +10,6 @@ * */ -#define AVMB1_COMPAT - #include "kcapi.h" #include <linux/module.h> #include <linux/mm.h> @@ -31,18 +29,12 @@ #include <linux/uaccess.h> #include <linux/isdn/capicmd.h> #include <linux/isdn/capiutil.h> -#ifdef AVMB1_COMPAT -#include <linux/b1lli.h> -#endif #include <linux/mutex.h> #include <linux/rcupdate.h> static int showcapimsgs = 0; static struct workqueue_struct *kcapi_wq; -MODULE_DESCRIPTION("CAPI4Linux: kernel CAPI layer"); -MODULE_AUTHOR("Carsten Paeth"); -MODULE_LICENSE("GPL"); module_param(showcapimsgs, uint, 0); /* ------------------------------------------------------------- */ @@ -61,9 +53,6 @@ static char capi_manufakturer[64] = "AVM Berlin"; #define NCCI2CTRL(ncci) (((ncci) >> 24) & 0x7f) -LIST_HEAD(capi_drivers); -DEFINE_MUTEX(capi_drivers_lock); - struct capi_ctr *capi_controller[CAPI_MAXCONTR]; DEFINE_MUTEX(capi_controller_lock); @@ -71,8 +60,6 @@ struct capi20_appl *capi_applications[CAPI_MAXAPPL]; static int ncontrollers; -static BLOCKING_NOTIFIER_HEAD(ctr_notifier_list); - /* -------- controller ref counting -------------------------------------- */ static inline struct capi_ctr * @@ -200,8 +187,6 @@ static void notify_up(u32 contr) if (ap) register_appl(ctr, applid, &ap->rparam); } - - wake_up_interruptible_all(&ctr->state_wait_queue); } else printk(KERN_WARNING "%s: invalid contr %d\n", __func__, contr); @@ -229,8 +214,6 @@ static void ctr_down(struct capi_ctr *ctr, int new_state) if (ap) capi_ctr_put(ctr); } - - wake_up_interruptible_all(&ctr->state_wait_queue); } static void notify_down(u32 contr) @@ -251,36 +234,23 @@ static void notify_down(u32 contr) mutex_unlock(&capi_controller_lock); } -static int -notify_handler(struct notifier_block *nb, unsigned long val, void *v) +static void do_notify_work(struct work_struct *work) { - u32 contr = (long)v; + struct capictr_event *event = + container_of(work, struct capictr_event, work); - switch (val) { + switch (event->type) { case CAPICTR_UP: - notify_up(contr); + notify_up(event->controller); break; case CAPICTR_DOWN: - notify_down(contr); + notify_down(event->controller); break; } - return NOTIFY_OK; -} -static void do_notify_work(struct work_struct *work) -{ - struct capictr_event *event = - container_of(work, struct capictr_event, work); - - blocking_notifier_call_chain(&ctr_notifier_list, event->type, - (void *)(long)event->controller); kfree(event); } -/* - * The notifier will result in adding/deleteing of devices. Devices can - * only removed in user process, not in bh. - */ static int notify_push(unsigned int event_type, u32 controller) { struct capictr_event *event = kmalloc(sizeof(*event), GFP_ATOMIC); @@ -296,18 +266,6 @@ static int notify_push(unsigned int event_type, u32 controller) return 0; } -int register_capictr_notifier(struct notifier_block *nb) -{ - return blocking_notifier_chain_register(&ctr_notifier_list, nb); -} -EXPORT_SYMBOL_GPL(register_capictr_notifier); - -int unregister_capictr_notifier(struct notifier_block *nb) -{ - return blocking_notifier_chain_unregister(&ctr_notifier_list, nb); -} -EXPORT_SYMBOL_GPL(unregister_capictr_notifier); - /* -------- Receiver ------------------------------------------ */ static void recv_handler(struct work_struct *work) @@ -454,48 +412,6 @@ void capi_ctr_down(struct capi_ctr *ctr) EXPORT_SYMBOL(capi_ctr_down); -/** - * capi_ctr_suspend_output() - suspend controller - * @ctr: controller descriptor structure. - * - * Called by hardware driver to stop data flow. - * - * Note: The caller is responsible for synchronizing concurrent state changes - * as well as invocations of capi_ctr_handle_message. - */ - -void capi_ctr_suspend_output(struct capi_ctr *ctr) -{ - if (!ctr->blocked) { - printk(KERN_DEBUG "kcapi: controller [%03d] suspend\n", - ctr->cnr); - ctr->blocked = 1; - } -} - -EXPORT_SYMBOL(capi_ctr_suspend_output); - -/** - * capi_ctr_resume_output() - resume controller - * @ctr: controller descriptor structure. - * - * Called by hardware driver to resume data flow. - * - * Note: The caller is responsible for synchronizing concurrent state changes - * as well as invocations of capi_ctr_handle_message. - */ - -void capi_ctr_resume_output(struct capi_ctr *ctr) -{ - if (ctr->blocked) { - printk(KERN_DEBUG "kcapi: controller [%03d] resumed\n", - ctr->cnr); - ctr->blocked = 0; - } -} - -EXPORT_SYMBOL(capi_ctr_resume_output); - /* ------------------------------------------------------------- */ /** @@ -531,7 +447,6 @@ int attach_capi_ctr(struct capi_ctr *ctr) ctr->state = CAPI_CTR_DETECTED; ctr->blocked = 0; ctr->traceflag = showcapimsgs; - init_waitqueue_head(&ctr->state_wait_queue); sprintf(ctr->procfn, "capi/controllers/%d", ctr->cnr); ctr->procent = proc_create_single_data(ctr->procfn, 0, NULL, @@ -586,38 +501,6 @@ unlock_out: EXPORT_SYMBOL(detach_capi_ctr); -/** - * register_capi_driver() - register CAPI driver - * @driver: driver descriptor structure. - * - * Called by hardware driver to register itself with the CAPI subsystem. - */ - -void register_capi_driver(struct capi_driver *driver) -{ - mutex_lock(&capi_drivers_lock); - list_add_tail(&driver->list, &capi_drivers); - mutex_unlock(&capi_drivers_lock); -} - -EXPORT_SYMBOL(register_capi_driver); - -/** - * unregister_capi_driver() - unregister CAPI driver - * @driver: driver descriptor structure. - * - * Called by hardware driver to unregister itself from the CAPI subsystem. - */ - -void unregister_capi_driver(struct capi_driver *driver) -{ - mutex_lock(&capi_drivers_lock); - list_del(&driver->list); - mutex_unlock(&capi_drivers_lock); -} - -EXPORT_SYMBOL(unregister_capi_driver); - /* ------------------------------------------------------------- */ /* -------- CAPI2.0 Interface ---------------------------------- */ /* ------------------------------------------------------------- */ @@ -648,8 +531,6 @@ u16 capi20_isinstalled(void) return ret; } -EXPORT_SYMBOL(capi20_isinstalled); - /** * capi20_register() - CAPI 2.0 operation CAPI_REGISTER * @ap: CAPI application descriptor structure. @@ -711,8 +592,6 @@ u16 capi20_register(struct capi20_appl *ap) return CAPI_NOERROR; } -EXPORT_SYMBOL(capi20_register); - /** * capi20_release() - CAPI 2.0 operation CAPI_RELEASE * @ap: CAPI application descriptor structure. @@ -755,8 +634,6 @@ u16 capi20_release(struct capi20_appl *ap) return CAPI_NOERROR; } -EXPORT_SYMBOL(capi20_release); - /** * capi20_put_message() - CAPI 2.0 operation CAPI_PUT_MESSAGE * @ap: CAPI application descriptor structure. @@ -834,8 +711,6 @@ u16 capi20_put_message(struct capi20_appl *ap, struct sk_buff *skb) return ctr->send_message(ctr, skb); } -EXPORT_SYMBOL(capi20_put_message); - /** * capi20_get_manufacturer() - CAPI 2.0 operation CAPI_GET_MANUFACTURER * @contr: controller number. @@ -869,8 +744,6 @@ u16 capi20_get_manufacturer(u32 contr, u8 *buf) return ret; } -EXPORT_SYMBOL(capi20_get_manufacturer); - /** * capi20_get_version() - CAPI 2.0 operation CAPI_GET_VERSION * @contr: controller number. @@ -904,8 +777,6 @@ u16 capi20_get_version(u32 contr, struct capi_version *verp) return ret; } -EXPORT_SYMBOL(capi20_get_version); - /** * capi20_get_serial() - CAPI 2.0 operation CAPI_GET_SERIAL_NUMBER * @contr: controller number. @@ -939,8 +810,6 @@ u16 capi20_get_serial(u32 contr, u8 *serial) return ret; } -EXPORT_SYMBOL(capi20_get_serial); - /** * capi20_get_profile() - CAPI 2.0 operation CAPI_GET_PROFILE * @contr: controller number. @@ -974,209 +843,6 @@ u16 capi20_get_profile(u32 contr, struct capi_profile *profp) return ret; } -EXPORT_SYMBOL(capi20_get_profile); - -/* Must be called with capi_controller_lock held. */ -static int wait_on_ctr_state(struct capi_ctr *ctr, unsigned int state) -{ - DEFINE_WAIT(wait); - int retval = 0; - - ctr = capi_ctr_get(ctr); - if (!ctr) - return -ESRCH; - - for (;;) { - prepare_to_wait(&ctr->state_wait_queue, &wait, - TASK_INTERRUPTIBLE); - - if (ctr->state == state) - break; - if (ctr->state == CAPI_CTR_DETACHED) { - retval = -ESRCH; - break; - } - if (signal_pending(current)) { - retval = -EINTR; - break; - } - - mutex_unlock(&capi_controller_lock); - schedule(); - mutex_lock(&capi_controller_lock); - } - finish_wait(&ctr->state_wait_queue, &wait); - - capi_ctr_put(ctr); - - return retval; -} - -#ifdef AVMB1_COMPAT -static int old_capi_manufacturer(unsigned int cmd, void __user *data) -{ - avmb1_loadandconfigdef ldef; - avmb1_extcarddef cdef; - avmb1_resetdef rdef; - capicardparams cparams; - struct capi_ctr *ctr; - struct capi_driver *driver = NULL; - capiloaddata ldata; - struct list_head *l; - int retval; - - switch (cmd) { - case AVMB1_ADDCARD: - case AVMB1_ADDCARD_WITH_TYPE: - if (cmd == AVMB1_ADDCARD) { - if ((retval = copy_from_user(&cdef, data, - sizeof(avmb1_carddef)))) - return -EFAULT; - cdef.cardtype = AVM_CARDTYPE_B1; - cdef.cardnr = 0; - } else { - if ((retval = copy_from_user(&cdef, data, - sizeof(avmb1_extcarddef)))) - return -EFAULT; - } - cparams.port = cdef.port; - cparams.irq = cdef.irq; - cparams.cardnr = cdef.cardnr; - - mutex_lock(&capi_drivers_lock); - - switch (cdef.cardtype) { - case AVM_CARDTYPE_B1: - list_for_each(l, &capi_drivers) { - driver = list_entry(l, struct capi_driver, list); - if (strcmp(driver->name, "b1isa") == 0) - break; - } - break; - case AVM_CARDTYPE_T1: - list_for_each(l, &capi_drivers) { - driver = list_entry(l, struct capi_driver, list); - if (strcmp(driver->name, "t1isa") == 0) - break; - } - break; - default: - driver = NULL; - break; - } - if (!driver) { - printk(KERN_ERR "kcapi: driver not loaded.\n"); - retval = -EIO; - } else if (!driver->add_card) { - printk(KERN_ERR "kcapi: driver has no add card function.\n"); - retval = -EIO; - } else - retval = driver->add_card(driver, &cparams); - - mutex_unlock(&capi_drivers_lock); - return retval; - - case AVMB1_LOAD: - case AVMB1_LOAD_AND_CONFIG: - - if (cmd == AVMB1_LOAD) { - if (copy_from_user(&ldef, data, - sizeof(avmb1_loaddef))) - return -EFAULT; - ldef.t4config.len = 0; - ldef.t4config.data = NULL; - } else { - if (copy_from_user(&ldef, data, - sizeof(avmb1_loadandconfigdef))) - return -EFAULT; - } - - mutex_lock(&capi_controller_lock); - - ctr = get_capi_ctr_by_nr(ldef.contr); - if (!ctr) { - retval = -EINVAL; - goto load_unlock_out; - } - - if (ctr->load_firmware == NULL) { - printk(KERN_DEBUG "kcapi: load: no load function\n"); - retval = -ESRCH; - goto load_unlock_out; - } - - if (ldef.t4file.len <= 0) { - printk(KERN_DEBUG "kcapi: load: invalid parameter: length of t4file is %d ?\n", ldef.t4file.len); - retval = -EINVAL; - goto load_unlock_out; - } - if (ldef.t4file.data == NULL) { - printk(KERN_DEBUG "kcapi: load: invalid parameter: dataptr is 0\n"); - retval = -EINVAL; - goto load_unlock_out; - } - - ldata.firmware.user = 1; - ldata.firmware.data = ldef.t4file.data; - ldata.firmware.len = ldef.t4file.len; - ldata.configuration.user = 1; - ldata.configuration.data = ldef.t4config.data; - ldata.configuration.len = ldef.t4config.len; - - if (ctr->state != CAPI_CTR_DETECTED) { - printk(KERN_INFO "kcapi: load: contr=%d not in detect state\n", ldef.contr); - retval = -EBUSY; - goto load_unlock_out; - } - ctr->state = CAPI_CTR_LOADING; - - retval = ctr->load_firmware(ctr, &ldata); - if (retval) { - ctr->state = CAPI_CTR_DETECTED; - goto load_unlock_out; - } - - retval = wait_on_ctr_state(ctr, CAPI_CTR_RUNNING); - - load_unlock_out: - mutex_unlock(&capi_controller_lock); - return retval; - - case AVMB1_RESETCARD: - if (copy_from_user(&rdef, data, sizeof(avmb1_resetdef))) - return -EFAULT; - - retval = 0; - - mutex_lock(&capi_controller_lock); - - ctr = get_capi_ctr_by_nr(rdef.contr); - if (!ctr) { - retval = -ESRCH; - goto reset_unlock_out; - } - - if (ctr->state == CAPI_CTR_DETECTED) - goto reset_unlock_out; - - if (ctr->reset_ctr == NULL) { - printk(KERN_DEBUG "kcapi: reset: no reset function\n"); - retval = -ESRCH; - goto reset_unlock_out; - } - - ctr->reset_ctr(ctr); - - retval = wait_on_ctr_state(ctr, CAPI_CTR_DETECTED); - - reset_unlock_out: - mutex_unlock(&capi_controller_lock); - return retval; - } - return -EINVAL; -} -#endif - /** * capi20_manufacturer() - CAPI 2.0 operation CAPI_MANUFACTURER * @cmd: command. @@ -1192,14 +858,6 @@ int capi20_manufacturer(unsigned long cmd, void __user *data) int retval; switch (cmd) { -#ifdef AVMB1_COMPAT - case AVMB1_LOAD: - case AVMB1_LOAD_AND_CONFIG: - case AVMB1_RESETCARD: - case AVMB1_GET_CARDINFO: - case AVMB1_REMOVECARD: - return old_capi_manufacturer(cmd, data); -#endif case KCAPI_CMD_TRACE: { kcapi_flagdef fdef; @@ -1222,43 +880,6 @@ int capi20_manufacturer(unsigned long cmd, void __user *data) return retval; } - case KCAPI_CMD_ADDCARD: - { - struct list_head *l; - struct capi_driver *driver = NULL; - capicardparams cparams; - kcapi_carddef cdef; - - if ((retval = copy_from_user(&cdef, data, sizeof(cdef)))) - return -EFAULT; - - cparams.port = cdef.port; - cparams.irq = cdef.irq; - cparams.membase = cdef.membase; - cparams.cardnr = cdef.cardnr; - cparams.cardtype = 0; - cdef.driver[sizeof(cdef.driver) - 1] = 0; - - mutex_lock(&capi_drivers_lock); - - list_for_each(l, &capi_drivers) { - driver = list_entry(l, struct capi_driver, list); - if (strcmp(driver->name, cdef.driver) == 0) - break; - } - if (driver == NULL) { - printk(KERN_ERR "kcapi: driver \"%s\" not loaded.\n", - cdef.driver); - retval = -ESRCH; - } else if (!driver->add_card) { - printk(KERN_ERR "kcapi: driver \"%s\" has no add card function.\n", cdef.driver); - retval = -EIO; - } else - retval = driver->add_card(driver, &cparams); - - mutex_unlock(&capi_drivers_lock); - return retval; - } default: printk(KERN_ERR "kcapi: manufacturer command %lu unknown.\n", @@ -1269,8 +890,6 @@ int capi20_manufacturer(unsigned long cmd, void __user *data) return -EINVAL; } -EXPORT_SYMBOL(capi20_manufacturer); - /* ------------------------------------------------------------- */ /* -------- Init & Cleanup ------------------------------------- */ /* ------------------------------------------------------------- */ @@ -1279,12 +898,7 @@ EXPORT_SYMBOL(capi20_manufacturer); * init / exit functions */ -static struct notifier_block capictr_nb = { - .notifier_call = notify_handler, - .priority = INT_MAX, -}; - -static int __init kcapi_init(void) +int __init kcapi_init(void) { int err; @@ -1292,11 +906,8 @@ static int __init kcapi_init(void) if (!kcapi_wq) return -ENOMEM; - register_capictr_notifier(&capictr_nb); - err = cdebug_init(); if (err) { - unregister_capictr_notifier(&capictr_nb); destroy_workqueue(kcapi_wq); return err; } @@ -1305,14 +916,10 @@ static int __init kcapi_init(void) return 0; } -static void __exit kcapi_exit(void) +void kcapi_exit(void) { kcapi_proc_exit(); - unregister_capictr_notifier(&capictr_nb); cdebug_exit(); destroy_workqueue(kcapi_wq); } - -module_init(kcapi_init); -module_exit(kcapi_exit); diff --git a/drivers/isdn/capi/kcapi.h b/drivers/isdn/capi/kcapi.h index 6d439f9a76b2..479623e1db2a 100644 --- a/drivers/isdn/capi/kcapi.h +++ b/drivers/isdn/capi/kcapi.h @@ -30,22 +30,153 @@ enum { CAPI_CTR_RUNNING = 3, }; -extern struct list_head capi_drivers; -extern struct mutex capi_drivers_lock; - extern struct capi_ctr *capi_controller[CAPI_MAXCONTR]; extern struct mutex capi_controller_lock; extern struct capi20_appl *capi_applications[CAPI_MAXAPPL]; -#ifdef CONFIG_PROC_FS - void kcapi_proc_init(void); void kcapi_proc_exit(void); -#else +struct capi20_appl { + u16 applid; + capi_register_params rparam; + void (*recv_message)(struct capi20_appl *ap, struct sk_buff *skb); + void *private; -static inline void kcapi_proc_init(void) { }; -static inline void kcapi_proc_exit(void) { }; + /* internal to kernelcapi.o */ + unsigned long nrecvctlpkt; + unsigned long nrecvdatapkt; + unsigned long nsentctlpkt; + unsigned long nsentdatapkt; + struct mutex recv_mtx; + struct sk_buff_head recv_queue; + struct work_struct recv_work; + int release_in_progress; +}; -#endif +u16 capi20_isinstalled(void); +u16 capi20_register(struct capi20_appl *ap); +u16 capi20_release(struct capi20_appl *ap); +u16 capi20_put_message(struct capi20_appl *ap, struct sk_buff *skb); +u16 capi20_get_manufacturer(u32 contr, u8 buf[CAPI_MANUFACTURER_LEN]); +u16 capi20_get_version(u32 contr, struct capi_version *verp); +u16 capi20_get_serial(u32 contr, u8 serial[CAPI_SERIAL_LEN]); +u16 capi20_get_profile(u32 contr, struct capi_profile *profp); +int capi20_manufacturer(unsigned long cmd, void __user *data); + +#define CAPICTR_UP 0 +#define CAPICTR_DOWN 1 + +int kcapi_init(void); +void kcapi_exit(void); + +/*----- basic-type definitions -----*/ + +typedef __u8 *_cstruct; + +typedef enum { + CAPI_COMPOSE, + CAPI_DEFAULT +} _cmstruct; + +/* + The _cmsg structure contains all possible CAPI 2.0 parameter. + All parameters are stored here first. The function CAPI_CMSG_2_MESSAGE + assembles the parameter and builds CAPI2.0 conform messages. + CAPI_MESSAGE_2_CMSG disassembles CAPI 2.0 messages and stores the + parameter in the _cmsg structure + */ + +typedef struct { + /* Header */ + __u16 ApplId; + __u8 Command; + __u8 Subcommand; + __u16 Messagenumber; + + /* Parameter */ + union { + __u32 adrController; + __u32 adrPLCI; + __u32 adrNCCI; + } adr; + + _cmstruct AdditionalInfo; + _cstruct B1configuration; + __u16 B1protocol; + _cstruct B2configuration; + __u16 B2protocol; + _cstruct B3configuration; + __u16 B3protocol; + _cstruct BC; + _cstruct BChannelinformation; + _cmstruct BProtocol; + _cstruct CalledPartyNumber; + _cstruct CalledPartySubaddress; + _cstruct CallingPartyNumber; + _cstruct CallingPartySubaddress; + __u32 CIPmask; + __u32 CIPmask2; + __u16 CIPValue; + __u32 Class; + _cstruct ConnectedNumber; + _cstruct ConnectedSubaddress; + __u32 Data; + __u16 DataHandle; + __u16 DataLength; + _cstruct FacilityConfirmationParameter; + _cstruct Facilitydataarray; + _cstruct FacilityIndicationParameter; + _cstruct FacilityRequestParameter; + __u16 FacilitySelector; + __u16 Flags; + __u32 Function; + _cstruct HLC; + __u16 Info; + _cstruct InfoElement; + __u32 InfoMask; + __u16 InfoNumber; + _cstruct Keypadfacility; + _cstruct LLC; + _cstruct ManuData; + __u32 ManuID; + _cstruct NCPI; + __u16 Reason; + __u16 Reason_B3; + __u16 Reject; + _cstruct Useruserdata; + + /* intern */ + unsigned l, p; + unsigned char *par; + __u8 *m; + + /* buffer to construct message */ + __u8 buf[180]; + +} _cmsg; + +/*-----------------------------------------------------------------------*/ + +/* + * Debugging / Tracing functions + */ + +char *capi_cmd2str(__u8 cmd, __u8 subcmd); + +typedef struct { + u_char *buf; + u_char *p; + size_t size; + size_t pos; +} _cdebbuf; + +#define CDEBUG_SIZE 1024 +#define CDEBUG_GSIZE 4096 + +void cdebbuf_free(_cdebbuf *cdb); +int cdebug_init(void); +void cdebug_exit(void); + +_cdebbuf *capi_message2str(__u8 *msg); diff --git a/drivers/isdn/capi/kcapi_proc.c b/drivers/isdn/capi/kcapi_proc.c index c94bd12c0f7c..eadbe59b3753 100644 --- a/drivers/isdn/capi/kcapi_proc.c +++ b/drivers/isdn/capi/kcapi_proc.c @@ -192,37 +192,15 @@ static const struct seq_operations seq_applstats_ops = { // --------------------------------------------------------------------------- -static void *capi_driver_start(struct seq_file *seq, loff_t *pos) - __acquires(&capi_drivers_lock) +/* /proc/capi/drivers is always empty */ +static ssize_t empty_read(struct file *file, char __user *buf, + size_t size, loff_t *off) { - mutex_lock(&capi_drivers_lock); - return seq_list_start(&capi_drivers, *pos); -} - -static void *capi_driver_next(struct seq_file *seq, void *v, loff_t *pos) -{ - return seq_list_next(v, &capi_drivers, pos); -} - -static void capi_driver_stop(struct seq_file *seq, void *v) - __releases(&capi_drivers_lock) -{ - mutex_unlock(&capi_drivers_lock); -} - -static int capi_driver_show(struct seq_file *seq, void *v) -{ - struct capi_driver *drv = list_entry(v, struct capi_driver, list); - - seq_printf(seq, "%-32s %s\n", drv->name, drv->revision); return 0; } -static const struct seq_operations seq_capi_driver_ops = { - .start = capi_driver_start, - .next = capi_driver_next, - .stop = capi_driver_stop, - .show = capi_driver_show, +static const struct file_operations empty_fops = { + .read = empty_read, }; // --------------------------------------------------------------------------- @@ -236,10 +214,10 @@ kcapi_proc_init(void) proc_create_seq("capi/contrstats", 0, NULL, &seq_contrstats_ops); proc_create_seq("capi/applications", 0, NULL, &seq_applications_ops); proc_create_seq("capi/applstats", 0, NULL, &seq_applstats_ops); - proc_create_seq("capi/driver", 0, NULL, &seq_capi_driver_ops); + proc_create("capi/driver", 0, NULL, &empty_fops); } -void __exit +void kcapi_proc_exit(void) { remove_proc_entry("capi/driver", NULL); diff --git a/drivers/staging/Kconfig b/drivers/staging/Kconfig index eaf753b70ec5..baccd7c883cc 100644 --- a/drivers/staging/Kconfig +++ b/drivers/staging/Kconfig @@ -42,10 +42,6 @@ source "drivers/staging/rtl8188eu/Kconfig" source "drivers/staging/rts5208/Kconfig" -source "drivers/staging/octeon/Kconfig" - -source "drivers/staging/octeon-usb/Kconfig" - source "drivers/staging/vt6655/Kconfig" source "drivers/staging/vt6656/Kconfig" @@ -116,8 +112,6 @@ source "drivers/staging/fieldbus/Kconfig" source "drivers/staging/kpc2000/Kconfig" -source "drivers/staging/isdn/Kconfig" - source "drivers/staging/wusbcore/Kconfig" source "drivers/staging/uwb/Kconfig" diff --git a/drivers/staging/Makefile b/drivers/staging/Makefile index 0a4396c9067b..fdd03fd6e704 100644 --- a/drivers/staging/Makefile +++ b/drivers/staging/Makefile @@ -12,8 +12,6 @@ obj-$(CONFIG_R8712U) += rtl8712/ obj-$(CONFIG_R8188EU) += rtl8188eu/ obj-$(CONFIG_RTS5208) += rts5208/ obj-$(CONFIG_NETLOGIC_XLR_NET) += netlogic/ -obj-$(CONFIG_OCTEON_ETHERNET) += octeon/ -obj-$(CONFIG_OCTEON_USB) += octeon-usb/ obj-$(CONFIG_VT6655) += vt6655/ obj-$(CONFIG_VT6656) += vt6656/ obj-$(CONFIG_VME_BUS) += vme/ @@ -48,10 +46,9 @@ obj-$(CONFIG_STAGING_GASKET_FRAMEWORK) += gasket/ obj-$(CONFIG_XIL_AXIS_FIFO) += axis-fifo/ obj-$(CONFIG_FIELDBUS_DEV) += fieldbus/ obj-$(CONFIG_KPC2000) += kpc2000/ -obj-$(CONFIG_ISDN_CAPI) += isdn/ obj-$(CONFIG_UWB) += uwb/ obj-$(CONFIG_USB_WUSB) += wusbcore/ -obj-$(CONFIG_EXFAT_FS) += exfat/ +obj-$(CONFIG_STAGING_EXFAT_FS) += exfat/ obj-$(CONFIG_QLGE) += qlge/ obj-$(CONFIG_NET_VENDOR_HP) += hp/ obj-$(CONFIG_WFX) += wfx/ diff --git a/drivers/staging/android/ashmem.c b/drivers/staging/android/ashmem.c index 74d497d39c5a..5891d0744a76 100644 --- a/drivers/staging/android/ashmem.c +++ b/drivers/staging/android/ashmem.c @@ -537,14 +537,14 @@ static int set_name(struct ashmem_area *asma, void __user *name) len = strncpy_from_user(local_name, name, ASHMEM_NAME_LEN); if (len < 0) return len; - if (len == ASHMEM_NAME_LEN) - local_name[ASHMEM_NAME_LEN - 1] = '\0'; + mutex_lock(&ashmem_mutex); /* cannot change an existing mapping's name */ if (asma->file) ret = -EINVAL; else - strcpy(asma->name + ASHMEM_NAME_PREFIX_LEN, local_name); + strscpy(asma->name + ASHMEM_NAME_PREFIX_LEN, local_name, + ASHMEM_NAME_LEN); mutex_unlock(&ashmem_mutex); return ret; diff --git a/drivers/staging/axis-fifo/axis-fifo.c b/drivers/staging/axis-fifo/axis-fifo.c index 39e6c59df1e9..5801067e7c1b 100644 --- a/drivers/staging/axis-fifo/axis-fifo.c +++ b/drivers/staging/axis-fifo/axis-fifo.c @@ -16,7 +16,7 @@ #include <linux/kernel.h> #include <linux/wait.h> -#include <linux/spinlock_types.h> +#include <linux/mutex.h> #include <linux/device.h> #include <linux/cdev.h> #include <linux/init.h> @@ -133,9 +133,9 @@ struct axis_fifo { int has_tx_fifo; /* whether the IP has the tx fifo enabled */ wait_queue_head_t read_queue; /* wait queue for asynchronos read */ - spinlock_t read_queue_lock; /* lock for reading waitqueue */ + struct mutex read_lock; /* lock for reading */ wait_queue_head_t write_queue; /* wait queue for asynchronos write */ - spinlock_t write_queue_lock; /* lock for writing waitqueue */ + struct mutex write_lock; /* lock for writing */ unsigned int write_flags; /* write file flags */ unsigned int read_flags; /* read file flags */ @@ -336,7 +336,21 @@ static void reset_ip_core(struct axis_fifo *fifo) iowrite32(XLLF_INT_ALL_MASK, fifo->base_addr + XLLF_ISR_OFFSET); } -/* reads a single packet from the fifo as dictated by the tlast signal */ +/** + * axis_fifo_write() - Read a packet from AXIS-FIFO character device. + * @f Open file. + * @buf User space buffer to read to. + * @len User space buffer length. + * @off Buffer offset. + * + * As defined by the device's documentation, we need to check the device's + * occupancy before reading the length register and then the data. All these + * operations must be executed atomically, in order and one after the other + * without missing any. + * + * Returns the number of bytes read from the device or negative error code + * on failure. + */ static ssize_t axis_fifo_read(struct file *f, char __user *buf, size_t len, loff_t *off) { @@ -350,36 +364,37 @@ static ssize_t axis_fifo_read(struct file *f, char __user *buf, u32 tmp_buf[READ_BUF_SIZE]; if (fifo->read_flags & O_NONBLOCK) { - /* opened in non-blocking mode - * return if there are no packets available + /* + * Device opened in non-blocking mode. Try to lock it and then + * check if any packet is available. */ - if (!ioread32(fifo->base_addr + XLLF_RDFO_OFFSET)) + if (!mutex_trylock(&fifo->read_lock)) return -EAGAIN; + + if (!ioread32(fifo->base_addr + XLLF_RDFO_OFFSET)) { + ret = -EAGAIN; + goto end_unlock; + } } else { /* opened in blocking mode * wait for a packet available interrupt (or timeout) * if nothing is currently available */ - spin_lock_irq(&fifo->read_queue_lock); - ret = wait_event_interruptible_lock_irq_timeout - (fifo->read_queue, - ioread32(fifo->base_addr + XLLF_RDFO_OFFSET), - fifo->read_queue_lock, - (read_timeout >= 0) ? msecs_to_jiffies(read_timeout) : + mutex_lock(&fifo->read_lock); + ret = wait_event_interruptible_timeout(fifo->read_queue, + ioread32(fifo->base_addr + XLLF_RDFO_OFFSET), + (read_timeout >= 0) ? msecs_to_jiffies(read_timeout) : MAX_SCHEDULE_TIMEOUT); - spin_unlock_irq(&fifo->read_queue_lock); - if (ret == 0) { - /* timeout occurred */ - dev_dbg(fifo->dt_device, "read timeout"); - return -EAGAIN; - } else if (ret == -ERESTARTSYS) { - /* signal received */ - return -ERESTARTSYS; - } else if (ret < 0) { - dev_err(fifo->dt_device, "wait_event_interruptible_timeout() error in read (ret=%i)\n", - ret); - return ret; + if (ret <= 0) { + if (ret == 0) { + ret = -EAGAIN; + } else if (ret != -ERESTARTSYS) { + dev_err(fifo->dt_device, "wait_event_interruptible_timeout() error in read (ret=%i)\n", + ret); + } + + goto end_unlock; } } @@ -387,14 +402,16 @@ static ssize_t axis_fifo_read(struct file *f, char __user *buf, if (!bytes_available) { dev_err(fifo->dt_device, "received a packet of length 0 - fifo core will be reset\n"); reset_ip_core(fifo); - return -EIO; + ret = -EIO; + goto end_unlock; } if (bytes_available > len) { dev_err(fifo->dt_device, "user read buffer too small (available bytes=%zu user buffer bytes=%zu) - fifo core will be reset\n", bytes_available, len); reset_ip_core(fifo); - return -EINVAL; + ret = -EINVAL; + goto end_unlock; } if (bytes_available % sizeof(u32)) { @@ -403,7 +420,8 @@ static ssize_t axis_fifo_read(struct file *f, char __user *buf, */ dev_err(fifo->dt_device, "received a packet that isn't word-aligned - fifo core will be reset\n"); reset_ip_core(fifo); - return -EIO; + ret = -EIO; + goto end_unlock; } words_available = bytes_available / sizeof(u32); @@ -423,16 +441,37 @@ static ssize_t axis_fifo_read(struct file *f, char __user *buf, if (copy_to_user(buf + copied * sizeof(u32), tmp_buf, copy * sizeof(u32))) { reset_ip_core(fifo); - return -EFAULT; + ret = -EFAULT; + goto end_unlock; } copied += copy; words_available -= copy; } - return bytes_available; + ret = bytes_available; + +end_unlock: + mutex_unlock(&fifo->read_lock); + + return ret; } +/** + * axis_fifo_write() - Write buffer to AXIS-FIFO character device. + * @f Open file. + * @buf User space buffer to write to the device. + * @len User space buffer length. + * @off Buffer offset. + * + * As defined by the device's documentation, we need to write to the device's + * data buffer then to the device's packet length register atomically. Also, + * we need to lock before checking if the device has available space to avoid + * any concurrency issue. + * + * Returns the number of bytes written to the device or negative error code + * on failure. + */ static ssize_t axis_fifo_write(struct file *f, const char __user *buf, size_t len, loff_t *off) { @@ -465,12 +504,17 @@ static ssize_t axis_fifo_write(struct file *f, const char __user *buf, } if (fifo->write_flags & O_NONBLOCK) { - /* opened in non-blocking mode - * return if there is not enough room available in the fifo + /* + * Device opened in non-blocking mode. Try to lock it and then + * check if there is any room to write the given buffer. */ + if (!mutex_trylock(&fifo->write_lock)) + return -EAGAIN; + if (words_to_write > ioread32(fifo->base_addr + XLLF_TDFV_OFFSET)) { - return -EAGAIN; + ret = -EAGAIN; + goto end_unlock; } } else { /* opened in blocking mode */ @@ -478,30 +522,22 @@ static ssize_t axis_fifo_write(struct file *f, const char __user *buf, /* wait for an interrupt (or timeout) if there isn't * currently enough room in the fifo */ - spin_lock_irq(&fifo->write_queue_lock); - ret = wait_event_interruptible_lock_irq_timeout - (fifo->write_queue, - ioread32(fifo->base_addr + XLLF_TDFV_OFFSET) + mutex_lock(&fifo->write_lock); + ret = wait_event_interruptible_timeout(fifo->write_queue, + ioread32(fifo->base_addr + XLLF_TDFV_OFFSET) >= words_to_write, - fifo->write_queue_lock, - (write_timeout >= 0) ? - msecs_to_jiffies(write_timeout) : + (write_timeout >= 0) ? msecs_to_jiffies(write_timeout) : MAX_SCHEDULE_TIMEOUT); - spin_unlock_irq(&fifo->write_queue_lock); - if (ret == 0) { - /* timeout occurred */ - dev_dbg(fifo->dt_device, "write timeout\n"); - return -EAGAIN; - } else if (ret == -ERESTARTSYS) { - /* signal received */ - return -ERESTARTSYS; - } else if (ret < 0) { - /* unknown error */ - dev_err(fifo->dt_device, - "wait_event_interruptible_timeout() error in write (ret=%i)\n", - ret); - return ret; + if (ret <= 0) { + if (ret == 0) { + ret = -EAGAIN; + } else if (ret != -ERESTARTSYS) { + dev_err(fifo->dt_device, "wait_event_interruptible_timeout() error in write (ret=%i)\n", + ret); + } + + goto end_unlock; } } @@ -515,7 +551,8 @@ static ssize_t axis_fifo_write(struct file *f, const char __user *buf, if (copy_from_user(tmp_buf, buf + copied * sizeof(u32), copy * sizeof(u32))) { reset_ip_core(fifo); - return -EFAULT; + ret = -EFAULT; + goto end_unlock; } for (i = 0; i < copy; i++) @@ -526,10 +563,15 @@ static ssize_t axis_fifo_write(struct file *f, const char __user *buf, words_to_write -= copy; } + ret = copied * sizeof(u32); + /* write packet size to fifo */ - iowrite32(copied * sizeof(u32), fifo->base_addr + XLLF_TLR_OFFSET); + iowrite32(ret, fifo->base_addr + XLLF_TLR_OFFSET); + +end_unlock: + mutex_unlock(&fifo->write_lock); - return (ssize_t)copied * sizeof(u32); + return ret; } static irqreturn_t axis_fifo_irq(int irq, void *dw) @@ -789,8 +831,8 @@ static int axis_fifo_probe(struct platform_device *pdev) init_waitqueue_head(&fifo->read_queue); init_waitqueue_head(&fifo->write_queue); - spin_lock_init(&fifo->read_queue_lock); - spin_lock_init(&fifo->write_queue_lock); + mutex_init(&fifo->read_lock); + mutex_init(&fifo->write_lock); /* ---------------------------- * init device memory space diff --git a/drivers/staging/comedi/drivers/das6402.c b/drivers/staging/comedi/drivers/das6402.c index f99211ec46de..04e224f8b779 100644 --- a/drivers/staging/comedi/drivers/das6402.c +++ b/drivers/staging/comedi/drivers/das6402.c @@ -279,7 +279,7 @@ static int das6402_ai_check_chanlist(struct comedi_device *dev, if (aref0 == AREF_DIFF && chan > (s->n_chan / 2)) { dev_dbg(dev->class_dev, - "chanlist differential channel to large\n"); + "chanlist differential channel too large\n"); return -EINVAL; } } diff --git a/drivers/staging/exfat/Kconfig b/drivers/staging/exfat/Kconfig index 0130019cbec2..292a19dfcaf5 100644 --- a/drivers/staging/exfat/Kconfig +++ b/drivers/staging/exfat/Kconfig @@ -1,41 +1,41 @@ # SPDX-License-Identifier: GPL-2.0 -config EXFAT_FS +config STAGING_EXFAT_FS tristate "exFAT fs support" depends on BLOCK select NLS help This adds support for the exFAT file system. -config EXFAT_DISCARD +config STAGING_EXFAT_DISCARD bool "enable discard support" - depends on EXFAT_FS + depends on STAGING_EXFAT_FS default y -config EXFAT_DELAYED_SYNC +config STAGING_EXFAT_DELAYED_SYNC bool "enable delayed sync" - depends on EXFAT_FS + depends on STAGING_EXFAT_FS default n -config EXFAT_KERNEL_DEBUG +config STAGING_EXFAT_KERNEL_DEBUG bool "enable kernel debug features via ioctl" - depends on EXFAT_FS + depends on STAGING_EXFAT_FS default n -config EXFAT_DEBUG_MSG +config STAGING_EXFAT_DEBUG_MSG bool "print debug messages" - depends on EXFAT_FS + depends on STAGING_EXFAT_FS default n -config EXFAT_DEFAULT_CODEPAGE +config STAGING_EXFAT_DEFAULT_CODEPAGE int "Default codepage for exFAT" default 437 - depends on EXFAT_FS + depends on STAGING_EXFAT_FS help This option should be set to the codepage of your exFAT filesystems. -config EXFAT_DEFAULT_IOCHARSET +config STAGING_EXFAT_DEFAULT_IOCHARSET string "Default iocharset for exFAT" default "utf8" - depends on EXFAT_FS + depends on STAGING_EXFAT_FS help Set this to the default input/output character set you'd like exFAT to use. diff --git a/drivers/staging/exfat/Makefile b/drivers/staging/exfat/Makefile index 6c90aec83feb..057556eeca0c 100644 --- a/drivers/staging/exfat/Makefile +++ b/drivers/staging/exfat/Makefile @@ -1,6 +1,6 @@ # SPDX-License-Identifier: GPL-2.0-or-later -obj-$(CONFIG_EXFAT_FS) += exfat.o +obj-$(CONFIG_STAGING_EXFAT_FS) += exfat.o exfat-y := exfat_core.o \ exfat_super.o \ diff --git a/drivers/staging/exfat/exfat.h b/drivers/staging/exfat/exfat.h index 51c665a924b7..4d87360fab35 100644 --- a/drivers/staging/exfat/exfat.h +++ b/drivers/staging/exfat/exfat.h @@ -9,7 +9,7 @@ #include <linux/types.h> #include <linux/buffer_head.h> -#ifdef CONFIG_EXFAT_KERNEL_DEBUG +#ifdef CONFIG_STAGING_EXFAT_KERNEL_DEBUG /* For Debugging Purpose */ /* IOCTL code 'f' used by * - file systems typically #0~0x1F @@ -22,9 +22,9 @@ #define EXFAT_DEBUGFLAGS_INVALID_UMOUNT 0x01 #define EXFAT_DEBUGFLAGS_ERROR_RW 0x02 -#endif /* CONFIG_EXFAT_KERNEL_DEBUG */ +#endif /* CONFIG_STAGING_EXFAT_KERNEL_DEBUG */ -#ifdef CONFIG_EXFAT_DEBUG_MSG +#ifdef CONFIG_STAGING_EXFAT_DEBUG_MSG #define DEBUG 1 #else #undef DEBUG @@ -516,49 +516,6 @@ struct buf_cache_t { struct buffer_head *buf_bh; }; -struct fs_func { - s32 (*alloc_cluster)(struct super_block *sb, s32 num_alloc, - struct chain_t *p_chain); - void (*free_cluster)(struct super_block *sb, struct chain_t *p_chain, - s32 do_relse); - s32 (*count_used_clusters)(struct super_block *sb); - - s32 (*init_dir_entry)(struct super_block *sb, struct chain_t *p_dir, - s32 entry, u32 type, u32 start_clu, u64 size); - s32 (*init_ext_entry)(struct super_block *sb, struct chain_t *p_dir, - s32 entry, s32 num_entries, - struct uni_name_t *p_uniname, - struct dos_name_t *p_dosname); - s32 (*find_dir_entry)(struct super_block *sb, struct chain_t *p_dir, - struct uni_name_t *p_uniname, s32 num_entries, - struct dos_name_t *p_dosname, u32 type); - void (*delete_dir_entry)(struct super_block *sb, - struct chain_t *p_dir, s32 entry, - s32 offset, s32 num_entries); - void (*get_uni_name_from_ext_entry)(struct super_block *sb, - struct chain_t *p_dir, s32 entry, - u16 *uniname); - s32 (*count_ext_entries)(struct super_block *sb, - struct chain_t *p_dir, s32 entry, - struct dentry_t *p_entry); - s32 (*calc_num_entries)(struct uni_name_t *p_uniname); - - u32 (*get_entry_type)(struct dentry_t *p_entry); - void (*set_entry_type)(struct dentry_t *p_entry, u32 type); - u32 (*get_entry_attr)(struct dentry_t *p_entry); - void (*set_entry_attr)(struct dentry_t *p_entry, u32 attr); - u8 (*get_entry_flag)(struct dentry_t *p_entry); - void (*set_entry_flag)(struct dentry_t *p_entry, u8 flag); - u32 (*get_entry_clu0)(struct dentry_t *p_entry); - void (*set_entry_clu0)(struct dentry_t *p_entry, u32 clu0); - u64 (*get_entry_size)(struct dentry_t *p_entry); - void (*set_entry_size)(struct dentry_t *p_entry, u64 size); - void (*get_entry_time)(struct dentry_t *p_entry, - struct timestamp_t *tp, u8 mode); - void (*set_entry_time)(struct dentry_t *p_entry, - struct timestamp_t *tp, u8 mode); -}; - struct fs_info_t { u32 drv; /* drive ID */ u32 vol_type; /* volume FAT type */ @@ -597,7 +554,6 @@ struct fs_info_t { u32 dev_ejected; /* block device operation error flag */ - struct fs_func *fs_func; struct mutex v_mutex; /* FAT cache */ @@ -661,10 +617,10 @@ struct exfat_mount_options { /* on error: continue, panic, remount-ro */ unsigned char errors; -#ifdef CONFIG_EXFAT_DISCARD +#ifdef CONFIG_STAGING_EXFAT_DISCARD /* flag on if -o dicard specified and device support discard() */ unsigned char discard; -#endif /* CONFIG_EXFAT_DISCARD */ +#endif /* CONFIG_STAGING_EXFAT_DISCARD */ }; #define EXFAT_HASH_BITS 8 @@ -700,9 +656,9 @@ struct exfat_sb_info { spinlock_t inode_hash_lock; struct hlist_head inode_hashtable[EXFAT_HASH_SIZE]; -#ifdef CONFIG_EXFAT_KERNEL_DEBUG +#ifdef CONFIG_STAGING_EXFAT_KERNEL_DEBUG long debug_flags; -#endif /* CONFIG_EXFAT_KERNEL_DEBUG */ +#endif /* CONFIG_STAGING_EXFAT_KERNEL_DEBUG */ }; /* @@ -829,5 +785,40 @@ int exfat_bdev_write(struct super_block *sb, sector_t secno, struct buffer_head *bh, u32 num_secs, bool sync); int exfat_bdev_sync(struct super_block *sb); +/* cluster operation functions */ +s32 exfat_alloc_cluster(struct super_block *sb, s32 num_alloc, + struct chain_t *p_chain); +void exfat_free_cluster(struct super_block *sb, struct chain_t *p_chain, + s32 do_relse); +s32 exfat_count_used_clusters(struct super_block *sb); + +/* dir operation functions */ +s32 exfat_find_dir_entry(struct super_block *sb, struct chain_t *p_dir, + struct uni_name_t *p_uniname, s32 num_entries, + struct dos_name_t *p_dosname, u32 type); +void exfat_delete_dir_entry(struct super_block *sb, struct chain_t *p_dir, + s32 entry, s32 order, s32 num_entries); +void exfat_get_uni_name_from_ext_entry(struct super_block *sb, + struct chain_t *p_dir, s32 entry, + u16 *uniname); +s32 exfat_count_ext_entries(struct super_block *sb, struct chain_t *p_dir, + s32 entry, struct dentry_t *p_entry); +s32 exfat_calc_num_entries(struct uni_name_t *p_uniname); + +/* dir entry getter/setter */ +u32 exfat_get_entry_type(struct dentry_t *p_entry); +u32 exfat_get_entry_attr(struct dentry_t *p_entry); +void exfat_set_entry_attr(struct dentry_t *p_entry, u32 attr); +u8 exfat_get_entry_flag(struct dentry_t *p_entry); +void exfat_set_entry_flag(struct dentry_t *p_entry, u8 flags); +u32 exfat_get_entry_clu0(struct dentry_t *p_entry); +void exfat_set_entry_clu0(struct dentry_t *p_entry, u32 start_clu); +u64 exfat_get_entry_size(struct dentry_t *p_entry); +void exfat_set_entry_size(struct dentry_t *p_entry, u64 size); +void exfat_get_entry_time(struct dentry_t *p_entry, struct timestamp_t *tp, + u8 mode); +void exfat_set_entry_time(struct dentry_t *p_entry, struct timestamp_t *tp, + u8 mode); + extern const u8 uni_upcase[]; #endif /* _EXFAT_H */ diff --git a/drivers/staging/exfat/exfat_blkdev.c b/drivers/staging/exfat/exfat_blkdev.c index 7bcd98b13109..0a3dc3568293 100644 --- a/drivers/staging/exfat/exfat_blkdev.c +++ b/drivers/staging/exfat/exfat_blkdev.c @@ -31,17 +31,17 @@ void exfat_bdev_close(struct super_block *sb) } int exfat_bdev_read(struct super_block *sb, sector_t secno, struct buffer_head **bh, - u32 num_secs, bool read) + u32 num_secs, bool read) { struct bd_info_t *p_bd = &(EXFAT_SB(sb)->bd_info); struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); -#ifdef CONFIG_EXFAT_KERNEL_DEBUG +#ifdef CONFIG_STAGING_EXFAT_KERNEL_DEBUG struct exfat_sb_info *sbi = EXFAT_SB(sb); long flags = sbi->debug_flags; if (flags & EXFAT_DEBUGFLAGS_ERROR_RW) return -EIO; -#endif /* CONFIG_EXFAT_KERNEL_DEBUG */ +#endif /* CONFIG_STAGING_EXFAT_KERNEL_DEBUG */ if (!p_bd->opened) return -ENODEV; @@ -66,19 +66,19 @@ int exfat_bdev_read(struct super_block *sb, sector_t secno, struct buffer_head * } int exfat_bdev_write(struct super_block *sb, sector_t secno, struct buffer_head *bh, - u32 num_secs, bool sync) + u32 num_secs, bool sync) { s32 count; struct buffer_head *bh2; struct bd_info_t *p_bd = &(EXFAT_SB(sb)->bd_info); struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); -#ifdef CONFIG_EXFAT_KERNEL_DEBUG +#ifdef CONFIG_STAGING_EXFAT_KERNEL_DEBUG struct exfat_sb_info *sbi = EXFAT_SB(sb); long flags = sbi->debug_flags; if (flags & EXFAT_DEBUGFLAGS_ERROR_RW) return -EIO; -#endif /* CONFIG_EXFAT_KERNEL_DEBUG */ +#endif /* CONFIG_STAGING_EXFAT_KERNEL_DEBUG */ if (!p_bd->opened) return -ENODEV; @@ -121,13 +121,13 @@ no_bh: int exfat_bdev_sync(struct super_block *sb) { struct bd_info_t *p_bd = &(EXFAT_SB(sb)->bd_info); -#ifdef CONFIG_EXFAT_KERNEL_DEBUG +#ifdef CONFIG_STAGING_EXFAT_KERNEL_DEBUG struct exfat_sb_info *sbi = EXFAT_SB(sb); long flags = sbi->debug_flags; if (flags & EXFAT_DEBUGFLAGS_ERROR_RW) return -EIO; -#endif /* CONFIG_EXFAT_KERNEL_DEBUG */ +#endif /* CONFIG_STAGING_EXFAT_KERNEL_DEBUG */ if (!p_bd->opened) return -ENODEV; diff --git a/drivers/staging/exfat/exfat_core.c b/drivers/staging/exfat/exfat_core.c index 794000e7bc6f..07b460d01334 100644 --- a/drivers/staging/exfat/exfat_core.c +++ b/drivers/staging/exfat/exfat_core.c @@ -177,11 +177,11 @@ static s32 clr_alloc_bitmap(struct super_block *sb, u32 clu) { int i, b; sector_t sector; -#ifdef CONFIG_EXFAT_DISCARD +#ifdef CONFIG_STAGING_EXFAT_DISCARD struct exfat_sb_info *sbi = EXFAT_SB(sb); struct exfat_mount_options *opts = &sbi->options; int ret; -#endif /* CONFIG_EXFAT_DISCARD */ +#endif /* CONFIG_STAGING_EXFAT_DISCARD */ struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); struct bd_info_t *p_bd = &(EXFAT_SB(sb)->bd_info); @@ -192,7 +192,7 @@ static s32 clr_alloc_bitmap(struct super_block *sb, u32 clu) exfat_bitmap_clear((u8 *)p_fs->vol_amap[i]->b_data, b); -#ifdef CONFIG_EXFAT_DISCARD +#ifdef CONFIG_STAGING_EXFAT_DISCARD if (opts->discard) { ret = sb_issue_discard(sb, START_SECTOR(clu), (1 << p_fs->sectors_per_clu_bits), @@ -204,7 +204,7 @@ static s32 clr_alloc_bitmap(struct super_block *sb, u32 clu) return ret; } } -#endif /* CONFIG_EXFAT_DISCARD */ +#endif /* CONFIG_STAGING_EXFAT_DISCARD */ return sector_write(sb, sector, p_fs->vol_amap[i], 0); } @@ -249,7 +249,7 @@ static u32 test_alloc_bitmap(struct super_block *sb, u32 clu) return CLUSTER_32(~0); } -static s32 exfat_alloc_cluster(struct super_block *sb, s32 num_alloc, +s32 exfat_alloc_cluster(struct super_block *sb, s32 num_alloc, struct chain_t *p_chain) { s32 num_clusters = 0; @@ -328,7 +328,7 @@ static s32 exfat_alloc_cluster(struct super_block *sb, s32 num_alloc, return num_clusters; } -static void exfat_free_cluster(struct super_block *sb, struct chain_t *p_chain, +void exfat_free_cluster(struct super_block *sb, struct chain_t *p_chain, s32 do_relse) { s32 num_clusters = 0; @@ -434,7 +434,7 @@ s32 count_num_clusters(struct super_block *sb, struct chain_t *p_chain) return count; } -static s32 exfat_count_used_clusters(struct super_block *sb) +s32 exfat_count_used_clusters(struct super_block *sb) { int i, map_i, map_b, count = 0; u8 k; @@ -499,7 +499,7 @@ s32 load_alloc_bitmap(struct super_block *sb) if (!ep) return -ENOENT; - type = p_fs->fs_func->get_entry_type((struct dentry_t *)ep); + type = exfat_get_entry_type((struct dentry_t *)ep); if (type == TYPE_UNUSED) break; @@ -745,7 +745,7 @@ s32 load_upcase_table(struct super_block *sb) if (!ep) return -ENOENT; - type = p_fs->fs_func->get_entry_type((struct dentry_t *)ep); + type = exfat_get_entry_type((struct dentry_t *)ep); if (type == TYPE_UNUSED) break; @@ -787,7 +787,7 @@ void free_upcase_table(struct super_block *sb) * Directory Entry Management Functions */ -static u32 exfat_get_entry_type(struct dentry_t *p_entry) +u32 exfat_get_entry_type(struct dentry_t *p_entry) { struct file_dentry_t *ep = (struct file_dentry_t *)p_entry; @@ -862,56 +862,56 @@ static void exfat_set_entry_type(struct dentry_t *p_entry, u32 type) } } -static u32 exfat_get_entry_attr(struct dentry_t *p_entry) +u32 exfat_get_entry_attr(struct dentry_t *p_entry) { struct file_dentry_t *ep = (struct file_dentry_t *)p_entry; return (u32)GET16_A(ep->attr); } -static void exfat_set_entry_attr(struct dentry_t *p_entry, u32 attr) +void exfat_set_entry_attr(struct dentry_t *p_entry, u32 attr) { struct file_dentry_t *ep = (struct file_dentry_t *)p_entry; SET16_A(ep->attr, (u16)attr); } -static u8 exfat_get_entry_flag(struct dentry_t *p_entry) +u8 exfat_get_entry_flag(struct dentry_t *p_entry) { struct strm_dentry_t *ep = (struct strm_dentry_t *)p_entry; return ep->flags; } -static void exfat_set_entry_flag(struct dentry_t *p_entry, u8 flags) +void exfat_set_entry_flag(struct dentry_t *p_entry, u8 flags) { struct strm_dentry_t *ep = (struct strm_dentry_t *)p_entry; ep->flags = flags; } -static u32 exfat_get_entry_clu0(struct dentry_t *p_entry) +u32 exfat_get_entry_clu0(struct dentry_t *p_entry) { struct strm_dentry_t *ep = (struct strm_dentry_t *)p_entry; return GET32_A(ep->start_clu); } -static void exfat_set_entry_clu0(struct dentry_t *p_entry, u32 start_clu) +void exfat_set_entry_clu0(struct dentry_t *p_entry, u32 start_clu) { struct strm_dentry_t *ep = (struct strm_dentry_t *)p_entry; SET32_A(ep->start_clu, start_clu); } -static u64 exfat_get_entry_size(struct dentry_t *p_entry) +u64 exfat_get_entry_size(struct dentry_t *p_entry) { struct strm_dentry_t *ep = (struct strm_dentry_t *)p_entry; return GET64_A(ep->valid_size); } -static void exfat_set_entry_size(struct dentry_t *p_entry, u64 size) +void exfat_set_entry_size(struct dentry_t *p_entry, u64 size) { struct strm_dentry_t *ep = (struct strm_dentry_t *)p_entry; @@ -919,7 +919,7 @@ static void exfat_set_entry_size(struct dentry_t *p_entry, u64 size) SET64_A(ep->size, size); } -static void exfat_get_entry_time(struct dentry_t *p_entry, struct timestamp_t *tp, +void exfat_get_entry_time(struct dentry_t *p_entry, struct timestamp_t *tp, u8 mode) { u16 t = 0x00, d = 0x21; @@ -948,7 +948,7 @@ static void exfat_get_entry_time(struct dentry_t *p_entry, struct timestamp_t *t tp->year = (d >> 9); } -static void exfat_set_entry_time(struct dentry_t *p_entry, struct timestamp_t *tp, +void exfat_set_entry_time(struct dentry_t *p_entry, struct timestamp_t *tp, u8 mode) { u16 t, d; @@ -1013,7 +1013,7 @@ static void init_name_entry(struct name_dentry_t *ep, u16 *uniname) } static s32 exfat_init_dir_entry(struct super_block *sb, struct chain_t *p_dir, - s32 entry, u32 type, u32 start_clu, u64 size) + s32 entry, u32 type, u32 start_clu, u64 size) { sector_t sector; u8 flags; @@ -1088,20 +1088,19 @@ static s32 exfat_init_ext_entry(struct super_block *sb, struct chain_t *p_dir, return 0; } -static void exfat_delete_dir_entry(struct super_block *sb, struct chain_t *p_dir, +void exfat_delete_dir_entry(struct super_block *sb, struct chain_t *p_dir, s32 entry, s32 order, s32 num_entries) { int i; sector_t sector; struct dentry_t *ep; - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); for (i = order; i < num_entries; i++) { ep = get_entry_in_dir(sb, p_dir, entry + i, §or); if (!ep) return; - p_fs->fs_func->set_entry_type(ep, TYPE_DELETED); + exfat_set_entry_type(ep, TYPE_DELETED); exfat_buf_modify(sb, sector); } } @@ -1256,7 +1255,7 @@ static s32 _walk_fat_chain(struct super_block *sb, struct chain_t *p_dir, } static s32 find_location(struct super_block *sb, struct chain_t *p_dir, s32 entry, - sector_t *sector, s32 *offset) + sector_t *sector, s32 *offset) { s32 off, ret; u32 clu = 0; @@ -1366,7 +1365,7 @@ struct entry_set_cache_t *get_entry_set_in_dir(struct super_block *sb, goto err_out; ep = (struct dentry_t *)(buf + off); - entry_type = p_fs->fs_func->get_entry_type(ep); + entry_type = exfat_get_entry_type(ep); if ((entry_type != TYPE_FILE) && (entry_type != TYPE_DIR)) goto err_out; @@ -1396,7 +1395,7 @@ struct entry_set_cache_t *get_entry_set_in_dir(struct super_block *sb, * instead of copying whole sector, we will check every entry. * this will provide minimum stablity and consistency. */ - entry_type = p_fs->fs_func->get_entry_type(ep); + entry_type = exfat_get_entry_type(ep); if ((entry_type == TYPE_UNUSED) || (entry_type == TYPE_DELETED)) goto err_out; @@ -1492,7 +1491,8 @@ void release_entry_set(struct entry_set_cache_t *es) /* search EMPTY CONTINUOUS "num_entries" entries */ static s32 search_deleted_or_unused_entry(struct super_block *sb, - struct chain_t *p_dir, s32 num_entries) + struct chain_t *p_dir, + s32 num_entries) { int i, dentry, num_empty = 0; s32 dentries_per_clu; @@ -1539,7 +1539,7 @@ static s32 search_deleted_or_unused_entry(struct super_block *sb, if (!ep) return -1; - type = p_fs->fs_func->get_entry_type(ep); + type = exfat_get_entry_type(ep); if (type == TYPE_UNUSED) { num_empty++; @@ -1613,7 +1613,7 @@ static s32 find_empty_entry(struct inode *inode, struct chain_t *p_dir, s32 num_ clu.flags = p_dir->flags; /* (1) allocate a cluster */ - ret = p_fs->fs_func->alloc_cluster(sb, 1, &clu); + ret = exfat_alloc_cluster(sb, 1, &clu); if (ret < 1) return -EIO; @@ -1649,8 +1649,8 @@ static s32 find_empty_entry(struct inode *inode, struct chain_t *p_dir, s32 num_ fid->entry + 1, §or); if (!ep) return -ENOENT; - p_fs->fs_func->set_entry_size(ep, size); - p_fs->fs_func->set_entry_flag(ep, p_dir->flags); + exfat_set_entry_size(ep, size); + exfat_set_entry_flag(ep, p_dir->flags); exfat_buf_modify(sb, sector); update_dir_checksum(sb, &fid->dir, @@ -1668,7 +1668,7 @@ static s32 find_empty_entry(struct inode *inode, struct chain_t *p_dir, s32 num_ } static s32 extract_uni_name_from_name_entry(struct name_dentry_t *ep, u16 *uniname, - s32 order) + s32 order) { int i, len = 0; @@ -1689,7 +1689,7 @@ static s32 extract_uni_name_from_name_entry(struct name_dentry_t *ep, u16 *unina * -1 : (root dir, ".") it is the root dir itself * -2 : entry with the name does not exist */ -static s32 exfat_find_dir_entry(struct super_block *sb, struct chain_t *p_dir, +s32 exfat_find_dir_entry(struct super_block *sb, struct chain_t *p_dir, struct uni_name_t *p_uniname, s32 num_entries, struct dos_name_t *p_dosname, u32 type) { @@ -1735,7 +1735,7 @@ static s32 exfat_find_dir_entry(struct super_block *sb, struct chain_t *p_dir, if (!ep) return -2; - entry_type = p_fs->fs_func->get_entry_type(ep); + entry_type = exfat_get_entry_type(ep); step = 1; if ((entry_type == TYPE_UNUSED) || (entry_type == TYPE_DELETED)) { @@ -1832,21 +1832,20 @@ static s32 exfat_find_dir_entry(struct super_block *sb, struct chain_t *p_dir, return -2; } -static s32 exfat_count_ext_entries(struct super_block *sb, struct chain_t *p_dir, +s32 exfat_count_ext_entries(struct super_block *sb, struct chain_t *p_dir, s32 entry, struct dentry_t *p_entry) { int i, count = 0; u32 type; struct file_dentry_t *file_ep = (struct file_dentry_t *)p_entry; struct dentry_t *ext_ep; - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); for (i = 0, entry++; i < file_ep->num_ext; i++, entry++) { ext_ep = get_entry_in_dir(sb, p_dir, entry, NULL); if (!ext_ep) return -1; - type = p_fs->fs_func->get_entry_type(ext_ep); + type = exfat_get_entry_type(ext_ep); if ((type == TYPE_EXTEND) || (type == TYPE_STREAM)) count++; else @@ -1884,7 +1883,7 @@ s32 count_dos_name_entries(struct super_block *sb, struct chain_t *p_dir, if (!ep) return -ENOENT; - entry_type = p_fs->fs_func->get_entry_type(ep); + entry_type = exfat_get_entry_type(ep); if (entry_type == TYPE_UNUSED) return count; @@ -1940,7 +1939,7 @@ bool is_dir_empty(struct super_block *sb, struct chain_t *p_dir) if (!ep) break; - type = p_fs->fs_func->get_entry_type(ep); + type = exfat_get_entry_type(ep); if (type == TYPE_UNUSED) return true; @@ -1984,9 +1983,8 @@ s32 get_num_entries_and_dos_name(struct super_block *sb, struct chain_t *p_dir, struct dos_name_t *p_dosname) { s32 num_entries; - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - num_entries = p_fs->fs_func->calc_num_entries(p_uniname); + num_entries = exfat_calc_num_entries(p_uniname); if (num_entries == 0) return -EINVAL; @@ -1995,14 +1993,13 @@ s32 get_num_entries_and_dos_name(struct super_block *sb, struct chain_t *p_dir, return 0; } -static void exfat_get_uni_name_from_ext_entry(struct super_block *sb, +void exfat_get_uni_name_from_ext_entry(struct super_block *sb, struct chain_t *p_dir, s32 entry, u16 *uniname) { int i; struct dentry_t *ep; struct entry_set_cache_t *es; - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); es = get_entry_set_in_dir(sb, p_dir, entry, ES_ALL_ENTRIES, &ep); if (!es || es->num_entries < 3) { @@ -2020,7 +2017,7 @@ static void exfat_get_uni_name_from_ext_entry(struct super_block *sb, * So, the index of first file-name dentry should start from 2. */ for (i = 2; i < es->num_entries; i++, ep++) { - if (p_fs->fs_func->get_entry_type(ep) == TYPE_EXTEND) + if (exfat_get_entry_type(ep) == TYPE_EXTEND) extract_uni_name_from_name_entry((struct name_dentry_t *) ep, uniname, i); else @@ -2032,7 +2029,7 @@ out: release_entry_set(es); } -static s32 exfat_calc_num_entries(struct uni_name_t *p_uniname) +s32 exfat_calc_num_entries(struct uni_name_t *p_uniname) { s32 len; @@ -2100,36 +2097,6 @@ s32 resolve_path(struct inode *inode, char *path, struct chain_t *p_dir, return 0; } -/* - * File Operation Functions - */ -static struct fs_func exfat_fs_func = { - .alloc_cluster = exfat_alloc_cluster, - .free_cluster = exfat_free_cluster, - .count_used_clusters = exfat_count_used_clusters, - - .init_dir_entry = exfat_init_dir_entry, - .init_ext_entry = exfat_init_ext_entry, - .find_dir_entry = exfat_find_dir_entry, - .delete_dir_entry = exfat_delete_dir_entry, - .get_uni_name_from_ext_entry = exfat_get_uni_name_from_ext_entry, - .count_ext_entries = exfat_count_ext_entries, - .calc_num_entries = exfat_calc_num_entries, - - .get_entry_type = exfat_get_entry_type, - .set_entry_type = exfat_set_entry_type, - .get_entry_attr = exfat_get_entry_attr, - .set_entry_attr = exfat_set_entry_attr, - .get_entry_flag = exfat_get_entry_flag, - .set_entry_flag = exfat_set_entry_flag, - .get_entry_clu0 = exfat_get_entry_clu0, - .set_entry_clu0 = exfat_set_entry_clu0, - .get_entry_size = exfat_get_entry_size, - .set_entry_size = exfat_set_entry_size, - .get_entry_time = exfat_get_entry_time, - .set_entry_time = exfat_set_entry_time, -}; - s32 exfat_mount(struct super_block *sb, struct pbr_sector_t *p_pbr) { struct bpbex_t *p_bpb = (struct bpbex_t *)p_pbr->bpb; @@ -2173,8 +2140,6 @@ s32 exfat_mount(struct super_block *sb, struct pbr_sector_t *p_pbr) p_fs->clu_srch_ptr = 2; p_fs->used_clusters = UINT_MAX; - p_fs->fs_func = &exfat_fs_func; - return 0; } @@ -2187,7 +2152,6 @@ s32 create_dir(struct inode *inode, struct chain_t *p_dir, struct dos_name_t dos_name; struct super_block *sb = inode->i_sb; struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - struct fs_func *fs_func = p_fs->fs_func; ret = get_num_entries_and_dos_name(sb, p_dir, p_uniname, &num_entries, &dos_name); @@ -2204,7 +2168,7 @@ s32 create_dir(struct inode *inode, struct chain_t *p_dir, clu.flags = (p_fs->vol_type == EXFAT) ? 0x03 : 0x01; /* (1) allocate a cluster */ - ret = fs_func->alloc_cluster(sb, 1, &clu); + ret = exfat_alloc_cluster(sb, 1, &clu); if (ret < 0) return ret; else if (ret == 0) @@ -2218,13 +2182,13 @@ s32 create_dir(struct inode *inode, struct chain_t *p_dir, /* (2) update the directory entry */ /* make sub-dir entry in parent directory */ - ret = fs_func->init_dir_entry(sb, p_dir, dentry, TYPE_DIR, clu.dir, - size); + ret = exfat_init_dir_entry(sb, p_dir, dentry, TYPE_DIR, clu.dir, + size); if (ret != 0) return ret; - ret = fs_func->init_ext_entry(sb, p_dir, dentry, num_entries, p_uniname, - &dos_name); + ret = exfat_init_ext_entry(sb, p_dir, dentry, num_entries, p_uniname, + &dos_name); if (ret != 0) return ret; @@ -2252,7 +2216,6 @@ s32 create_file(struct inode *inode, struct chain_t *p_dir, struct dos_name_t dos_name; struct super_block *sb = inode->i_sb; struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - struct fs_func *fs_func = p_fs->fs_func; ret = get_num_entries_and_dos_name(sb, p_dir, p_uniname, &num_entries, &dos_name); @@ -2268,13 +2231,13 @@ s32 create_file(struct inode *inode, struct chain_t *p_dir, /* fill the dos name directory entry information of the created file. * the first cluster is not determined yet. (0) */ - ret = fs_func->init_dir_entry(sb, p_dir, dentry, TYPE_FILE | mode, - CLUSTER_32(0), 0); + ret = exfat_init_dir_entry(sb, p_dir, dentry, TYPE_FILE | mode, + CLUSTER_32(0), 0); if (ret != 0) return ret; - ret = fs_func->init_ext_entry(sb, p_dir, dentry, num_entries, p_uniname, - &dos_name); + ret = exfat_init_ext_entry(sb, p_dir, dentry, num_entries, p_uniname, + &dos_name); if (ret != 0) return ret; @@ -2301,8 +2264,6 @@ void remove_file(struct inode *inode, struct chain_t *p_dir, s32 entry) sector_t sector; struct dentry_t *ep; struct super_block *sb = inode->i_sb; - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - struct fs_func *fs_func = p_fs->fs_func; ep = get_entry_in_dir(sb, p_dir, entry, §or); if (!ep) @@ -2311,7 +2272,7 @@ void remove_file(struct inode *inode, struct chain_t *p_dir, s32 entry) exfat_buf_lock(sb, sector); /* exfat_buf_lock() before call count_ext_entries() */ - num_entries = fs_func->count_ext_entries(sb, p_dir, entry, ep); + num_entries = exfat_count_ext_entries(sb, p_dir, entry, ep); if (num_entries < 0) { exfat_buf_unlock(sb, sector); return; @@ -2321,7 +2282,7 @@ void remove_file(struct inode *inode, struct chain_t *p_dir, s32 entry) exfat_buf_unlock(sb, sector); /* (1) update the directory entry */ - fs_func->delete_dir_entry(sb, p_dir, entry, 0, num_entries); + exfat_delete_dir_entry(sb, p_dir, entry, 0, num_entries); } s32 exfat_rename_file(struct inode *inode, struct chain_t *p_dir, s32 oldentry, @@ -2332,8 +2293,6 @@ s32 exfat_rename_file(struct inode *inode, struct chain_t *p_dir, s32 oldentry, struct dos_name_t dos_name; struct dentry_t *epold, *epnew; struct super_block *sb = inode->i_sb; - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - struct fs_func *fs_func = p_fs->fs_func; epold = get_entry_in_dir(sb, p_dir, oldentry, §or_old); if (!epold) @@ -2342,8 +2301,8 @@ s32 exfat_rename_file(struct inode *inode, struct chain_t *p_dir, s32 oldentry, exfat_buf_lock(sb, sector_old); /* exfat_buf_lock() before call count_ext_entries() */ - num_old_entries = fs_func->count_ext_entries(sb, p_dir, oldentry, - epold); + num_old_entries = exfat_count_ext_entries(sb, p_dir, oldentry, + epold); if (num_old_entries < 0) { exfat_buf_unlock(sb, sector_old); return -ENOENT; @@ -2371,10 +2330,10 @@ s32 exfat_rename_file(struct inode *inode, struct chain_t *p_dir, s32 oldentry, } memcpy((void *)epnew, (void *)epold, DENTRY_SIZE); - if (fs_func->get_entry_type(epnew) == TYPE_FILE) { - fs_func->set_entry_attr(epnew, - fs_func->get_entry_attr(epnew) | - ATTR_ARCHIVE); + if (exfat_get_entry_type(epnew) == TYPE_FILE) { + exfat_set_entry_attr(epnew, + exfat_get_entry_attr(epnew) | + ATTR_ARCHIVE); fid->attr |= ATTR_ARCHIVE; } exfat_buf_modify(sb, sector_new); @@ -2395,33 +2354,33 @@ s32 exfat_rename_file(struct inode *inode, struct chain_t *p_dir, s32 oldentry, exfat_buf_modify(sb, sector_new); exfat_buf_unlock(sb, sector_old); - ret = fs_func->init_ext_entry(sb, p_dir, newentry, - num_new_entries, p_uniname, - &dos_name); + ret = exfat_init_ext_entry(sb, p_dir, newentry, + num_new_entries, p_uniname, + &dos_name); if (ret != 0) return ret; - fs_func->delete_dir_entry(sb, p_dir, oldentry, 0, - num_old_entries); + exfat_delete_dir_entry(sb, p_dir, oldentry, 0, + num_old_entries); fid->entry = newentry; } else { - if (fs_func->get_entry_type(epold) == TYPE_FILE) { - fs_func->set_entry_attr(epold, - fs_func->get_entry_attr(epold) | - ATTR_ARCHIVE); + if (exfat_get_entry_type(epold) == TYPE_FILE) { + exfat_set_entry_attr(epold, + exfat_get_entry_attr(epold) | + ATTR_ARCHIVE); fid->attr |= ATTR_ARCHIVE; } exfat_buf_modify(sb, sector_old); exfat_buf_unlock(sb, sector_old); - ret = fs_func->init_ext_entry(sb, p_dir, oldentry, - num_new_entries, p_uniname, - &dos_name); + ret = exfat_init_ext_entry(sb, p_dir, oldentry, + num_new_entries, p_uniname, + &dos_name); if (ret != 0) return ret; - fs_func->delete_dir_entry(sb, p_dir, oldentry, num_new_entries, - num_old_entries); + exfat_delete_dir_entry(sb, p_dir, oldentry, num_new_entries, + num_old_entries); } return 0; @@ -2436,23 +2395,21 @@ s32 move_file(struct inode *inode, struct chain_t *p_olddir, s32 oldentry, struct dos_name_t dos_name; struct dentry_t *epmov, *epnew; struct super_block *sb = inode->i_sb; - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - struct fs_func *fs_func = p_fs->fs_func; epmov = get_entry_in_dir(sb, p_olddir, oldentry, §or_mov); if (!epmov) return -ENOENT; /* check if the source and target directory is the same */ - if (fs_func->get_entry_type(epmov) == TYPE_DIR && - fs_func->get_entry_clu0(epmov) == p_newdir->dir) + if (exfat_get_entry_type(epmov) == TYPE_DIR && + exfat_get_entry_clu0(epmov) == p_newdir->dir) return -EINVAL; exfat_buf_lock(sb, sector_mov); /* exfat_buf_lock() before call count_ext_entries() */ - num_old_entries = fs_func->count_ext_entries(sb, p_olddir, oldentry, - epmov); + num_old_entries = exfat_count_ext_entries(sb, p_olddir, oldentry, + epmov); if (num_old_entries < 0) { exfat_buf_unlock(sb, sector_mov); return -ENOENT; @@ -2479,9 +2436,9 @@ s32 move_file(struct inode *inode, struct chain_t *p_olddir, s32 oldentry, } memcpy((void *)epnew, (void *)epmov, DENTRY_SIZE); - if (fs_func->get_entry_type(epnew) == TYPE_FILE) { - fs_func->set_entry_attr(epnew, fs_func->get_entry_attr(epnew) | - ATTR_ARCHIVE); + if (exfat_get_entry_type(epnew) == TYPE_FILE) { + exfat_set_entry_attr(epnew, exfat_get_entry_attr(epnew) | + ATTR_ARCHIVE); fid->attr |= ATTR_ARCHIVE; } exfat_buf_modify(sb, sector_new); @@ -2501,12 +2458,12 @@ s32 move_file(struct inode *inode, struct chain_t *p_olddir, s32 oldentry, exfat_buf_modify(sb, sector_new); exfat_buf_unlock(sb, sector_mov); - ret = fs_func->init_ext_entry(sb, p_newdir, newentry, num_new_entries, - p_uniname, &dos_name); + ret = exfat_init_ext_entry(sb, p_newdir, newentry, num_new_entries, + p_uniname, &dos_name); if (ret != 0) return ret; - fs_func->delete_dir_entry(sb, p_olddir, oldentry, 0, num_old_entries); + exfat_delete_dir_entry(sb, p_olddir, oldentry, 0, num_old_entries); fid->dir.dir = p_newdir->dir; fid->dir.size = p_newdir->size; diff --git a/drivers/staging/exfat/exfat_super.c b/drivers/staging/exfat/exfat_super.c index 9f91853b189b..b81d2a87b82e 100644 --- a/drivers/staging/exfat/exfat_super.c +++ b/drivers/staging/exfat/exfat_super.c @@ -38,8 +38,8 @@ static struct kmem_cache *exfat_inode_cachep; -static int exfat_default_codepage = CONFIG_EXFAT_DEFAULT_CODEPAGE; -static char exfat_default_iocharset[] = CONFIG_EXFAT_DEFAULT_IOCHARSET; +static int exfat_default_codepage = CONFIG_STAGING_EXFAT_DEFAULT_CODEPAGE; +static char exfat_default_iocharset[] = CONFIG_STAGING_EXFAT_DEFAULT_IOCHARSET; #define INC_IVERSION(x) (inode_inc_iversion(x)) #define GET_IVERSION(x) (inode_peek_iversion_raw(x)) @@ -365,7 +365,7 @@ static int ffsMountVol(struct super_block *sb) if (p_bd->sector_size < sb->s_blocksize) { printk(KERN_INFO "EXFAT: mount failed - sector size %d less than blocksize %ld\n", - p_bd->sector_size, sb->s_blocksize); + p_bd->sector_size, sb->s_blocksize); ret = -EINVAL; goto out; } @@ -492,7 +492,7 @@ static int ffsGetVolInfo(struct super_block *sb, struct vol_info_t *info) mutex_lock(&p_fs->v_mutex); if (p_fs->used_clusters == UINT_MAX) - p_fs->used_clusters = p_fs->fs_func->count_used_clusters(sb); + p_fs->used_clusters = exfat_count_used_clusters(sb); info->FatType = p_fs->vol_type; info->ClusterSize = p_fs->cluster_size; @@ -565,8 +565,8 @@ static int ffsLookupFile(struct inode *inode, char *path, struct file_id_t *fid) goto out; /* search the file name for directories */ - dentry = p_fs->fs_func->find_dir_entry(sb, &dir, &uni_name, num_entries, - &dos_name, TYPE_ALL); + dentry = exfat_find_dir_entry(sb, &dir, &uni_name, num_entries, + &dos_name, TYPE_ALL); if (dentry < -1) { ret = -ENOENT; goto out; @@ -595,18 +595,18 @@ static int ffsLookupFile(struct inode *inode, char *path, struct file_id_t *fid) } ep2 = ep + 1; - fid->type = p_fs->fs_func->get_entry_type(ep); + fid->type = exfat_get_entry_type(ep); fid->rwoffset = 0; fid->hint_last_off = -1; - fid->attr = p_fs->fs_func->get_entry_attr(ep); + fid->attr = exfat_get_entry_attr(ep); - fid->size = p_fs->fs_func->get_entry_size(ep2); + fid->size = exfat_get_entry_size(ep2); if ((fid->type == TYPE_FILE) && (fid->size == 0)) { fid->flags = (p_fs->vol_type == EXFAT) ? 0x03 : 0x01; fid->start_clu = CLUSTER_32(~0); } else { - fid->flags = p_fs->fs_func->get_entry_flag(ep2); - fid->start_clu = p_fs->fs_func->get_entry_clu0(ep2); + fid->flags = exfat_get_entry_flag(ep2); + fid->start_clu = exfat_get_entry_clu0(ep2); } release_entry_set(es); @@ -647,7 +647,7 @@ static int ffsCreateFile(struct inode *inode, char *path, u8 mode, /* create a new file */ ret = create_file(inode, &dir, &uni_name, mode, fid); -#ifndef CONFIG_EXFAT_DELAYED_SYNC +#ifndef CONFIG_STAGING_EXFAT_DELAYED_SYNC fs_sync(sb, true); fs_set_vol_flags(sb, VOL_CLEAN); #endif @@ -886,9 +886,9 @@ static int ffsWriteFile(struct inode *inode, struct file_id_t *fid, new_clu.flags = fid->flags; /* (1) allocate a chain of clusters */ - num_alloced = p_fs->fs_func->alloc_cluster(sb, - num_alloc, - &new_clu); + num_alloced = exfat_alloc_cluster(sb, + num_alloc, + &new_clu); if (num_alloced == 0) break; if (num_alloced < 0) { @@ -991,24 +991,24 @@ static int ffsWriteFile(struct inode *inode, struct file_id_t *fid, goto err_out; ep2 = ep + 1; - p_fs->fs_func->set_entry_time(ep, tm_current(&tm), TM_MODIFY); - p_fs->fs_func->set_entry_attr(ep, fid->attr); + exfat_set_entry_time(ep, tm_current(&tm), TM_MODIFY); + exfat_set_entry_attr(ep, fid->attr); if (modified) { - if (p_fs->fs_func->get_entry_flag(ep2) != fid->flags) - p_fs->fs_func->set_entry_flag(ep2, fid->flags); + if (exfat_get_entry_flag(ep2) != fid->flags) + exfat_set_entry_flag(ep2, fid->flags); - if (p_fs->fs_func->get_entry_size(ep2) != fid->size) - p_fs->fs_func->set_entry_size(ep2, fid->size); + if (exfat_get_entry_size(ep2) != fid->size) + exfat_set_entry_size(ep2, fid->size); - if (p_fs->fs_func->get_entry_clu0(ep2) != fid->start_clu) - p_fs->fs_func->set_entry_clu0(ep2, fid->start_clu); + if (exfat_get_entry_clu0(ep2) != fid->start_clu) + exfat_set_entry_clu0(ep2, fid->start_clu); } update_dir_checksum_with_entry_set(sb, es); release_entry_set(es); -#ifndef CONFIG_EXFAT_DELAYED_SYNC +#ifndef CONFIG_STAGING_EXFAT_DELAYED_SYNC fs_sync(sb, true); fs_set_vol_flags(sb, VOL_CLEAN); #endif @@ -1108,13 +1108,13 @@ static int ffsTruncateFile(struct inode *inode, u64 old_size, u64 new_size) } ep2 = ep + 1; - p_fs->fs_func->set_entry_time(ep, tm_current(&tm), TM_MODIFY); - p_fs->fs_func->set_entry_attr(ep, fid->attr); + exfat_set_entry_time(ep, tm_current(&tm), TM_MODIFY); + exfat_set_entry_attr(ep, fid->attr); - p_fs->fs_func->set_entry_size(ep2, new_size); + exfat_set_entry_size(ep2, new_size); if (new_size == 0) { - p_fs->fs_func->set_entry_flag(ep2, 0x01); - p_fs->fs_func->set_entry_clu0(ep2, CLUSTER_32(0)); + exfat_set_entry_flag(ep2, 0x01); + exfat_set_entry_clu0(ep2, CLUSTER_32(0)); } update_dir_checksum_with_entry_set(sb, es); @@ -1127,14 +1127,14 @@ static int ffsTruncateFile(struct inode *inode, u64 old_size, u64 new_size) } /* (3) free the clusters */ - p_fs->fs_func->free_cluster(sb, &clu, 0); + exfat_free_cluster(sb, &clu, 0); /* hint information */ fid->hint_last_off = -1; if (fid->rwoffset > fid->size) fid->rwoffset = fid->size; -#ifndef CONFIG_EXFAT_DELAYED_SYNC +#ifndef CONFIG_STAGING_EXFAT_DELAYED_SYNC fs_sync(sb, true); fs_set_vol_flags(sb, VOL_CLEAN); #endif @@ -1217,7 +1217,7 @@ static int ffsMoveFile(struct inode *old_parent_inode, struct file_id_t *fid, goto out2; } - if (p_fs->fs_func->get_entry_attr(ep) & ATTR_READONLY) { + if (exfat_get_entry_attr(ep) & ATTR_READONLY) { ret = -EPERM; goto out2; } @@ -1237,7 +1237,7 @@ static int ffsMoveFile(struct inode *old_parent_inode, struct file_id_t *fid, if (!ep) goto out; - entry_type = p_fs->fs_func->get_entry_type(ep); + entry_type = exfat_get_entry_type(ep); if (entry_type == TYPE_DIR) { struct chain_t new_clu; @@ -1274,15 +1274,15 @@ static int ffsMoveFile(struct inode *old_parent_inode, struct file_id_t *fid, if (!ep) goto out; - num_entries = p_fs->fs_func->count_ext_entries(sb, p_dir, - new_entry, ep); + num_entries = exfat_count_ext_entries(sb, p_dir, + new_entry, ep); if (num_entries < 0) goto out; - p_fs->fs_func->delete_dir_entry(sb, p_dir, new_entry, 0, - num_entries + 1); + exfat_delete_dir_entry(sb, p_dir, new_entry, 0, + num_entries + 1); } out: -#ifndef CONFIG_EXFAT_DELAYED_SYNC +#ifndef CONFIG_STAGING_EXFAT_DELAYED_SYNC fs_sync(sb, true); fs_set_vol_flags(sb, VOL_CLEAN); #endif @@ -1324,7 +1324,7 @@ static int ffsRemoveFile(struct inode *inode, struct file_id_t *fid) goto out; } - if (p_fs->fs_func->get_entry_attr(ep) & ATTR_READONLY) { + if (exfat_get_entry_attr(ep) & ATTR_READONLY) { ret = -EPERM; goto out; } @@ -1338,13 +1338,13 @@ static int ffsRemoveFile(struct inode *inode, struct file_id_t *fid) clu_to_free.flags = fid->flags; /* (2) free the clusters */ - p_fs->fs_func->free_cluster(sb, &clu_to_free, 0); + exfat_free_cluster(sb, &clu_to_free, 0); fid->size = 0; fid->start_clu = CLUSTER_32(~0); fid->flags = (p_fs->vol_type == EXFAT) ? 0x03 : 0x01; -#ifndef CONFIG_EXFAT_DELAYED_SYNC +#ifndef CONFIG_STAGING_EXFAT_DELAYED_SYNC fs_sync(sb, true); fs_set_vol_flags(sb, VOL_CLEAN); #endif @@ -1398,7 +1398,7 @@ static int ffsSetAttr(struct inode *inode, u32 attr) goto out; } - type = p_fs->fs_func->get_entry_type(ep); + type = exfat_get_entry_type(ep); if (((type == TYPE_FILE) && (attr & ATTR_SUBDIR)) || ((type == TYPE_DIR) && (!(attr & ATTR_SUBDIR)))) { @@ -1415,12 +1415,12 @@ static int ffsSetAttr(struct inode *inode, u32 attr) /* set the file attribute */ fid->attr = attr; - p_fs->fs_func->set_entry_attr(ep, attr); + exfat_set_entry_attr(ep, attr); update_dir_checksum_with_entry_set(sb, es); release_entry_set(es); -#ifndef CONFIG_EXFAT_DELAYED_SYNC +#ifndef CONFIG_STAGING_EXFAT_DELAYED_SYNC fs_sync(sb, true); fs_set_vol_flags(sb, VOL_CLEAN); #endif @@ -1481,7 +1481,7 @@ static int ffsReadStat(struct inode *inode, struct dir_entry_t *info) count = count_dos_name_entries(sb, &dir, TYPE_DIR); if (count < 0) { - ret = count; /* propogate error upward */ + ret = count; /* propagate error upward */ goto out; } info->NumSubdirs = count; @@ -1502,9 +1502,9 @@ static int ffsReadStat(struct inode *inode, struct dir_entry_t *info) ep2 = ep + 1; /* set FILE_INFO structure using the acquired struct dentry_t */ - info->Attr = p_fs->fs_func->get_entry_attr(ep); + info->Attr = exfat_get_entry_attr(ep); - p_fs->fs_func->get_entry_time(ep, &tm, TM_CREATE); + exfat_get_entry_time(ep, &tm, TM_CREATE); info->CreateTimestamp.Year = tm.year; info->CreateTimestamp.Month = tm.mon; info->CreateTimestamp.Day = tm.day; @@ -1513,7 +1513,7 @@ static int ffsReadStat(struct inode *inode, struct dir_entry_t *info) info->CreateTimestamp.Second = tm.sec; info->CreateTimestamp.MilliSecond = 0; - p_fs->fs_func->get_entry_time(ep, &tm, TM_MODIFY); + exfat_get_entry_time(ep, &tm, TM_MODIFY); info->ModifyTimestamp.Year = tm.year; info->ModifyTimestamp.Month = tm.mon; info->ModifyTimestamp.Day = tm.day; @@ -1528,13 +1528,13 @@ static int ffsReadStat(struct inode *inode, struct dir_entry_t *info) /* XXX this is very bad for exfat cuz name is already included in es. * API should be revised */ - p_fs->fs_func->get_uni_name_from_ext_entry(sb, &fid->dir, fid->entry, - uni_name.name); + exfat_get_uni_name_from_ext_entry(sb, &fid->dir, fid->entry, + uni_name.name); nls_uniname_to_cstring(sb, info->Name, &uni_name); info->NumSubdirs = 2; - info->Size = p_fs->fs_func->get_entry_size(ep2); + info->Size = exfat_get_entry_size(ep2); release_entry_set(es); @@ -1548,7 +1548,7 @@ static int ffsReadStat(struct inode *inode, struct dir_entry_t *info) count = count_dos_name_entries(sb, &dir, TYPE_DIR); if (count < 0) { - ret = count; /* propogate error upward */ + ret = count; /* propagate error upward */ goto out; } info->NumSubdirs += count; @@ -1602,7 +1602,7 @@ static int ffsWriteStat(struct inode *inode, struct dir_entry_t *info) } ep2 = ep + 1; - p_fs->fs_func->set_entry_attr(ep, info->Attr); + exfat_set_entry_attr(ep, info->Attr); /* set FILE_INFO structure using the acquired struct dentry_t */ tm.sec = info->CreateTimestamp.Second; @@ -1611,7 +1611,7 @@ static int ffsWriteStat(struct inode *inode, struct dir_entry_t *info) tm.day = info->CreateTimestamp.Day; tm.mon = info->CreateTimestamp.Month; tm.year = info->CreateTimestamp.Year; - p_fs->fs_func->set_entry_time(ep, &tm, TM_CREATE); + exfat_set_entry_time(ep, &tm, TM_CREATE); tm.sec = info->ModifyTimestamp.Second; tm.min = info->ModifyTimestamp.Minute; @@ -1619,9 +1619,9 @@ static int ffsWriteStat(struct inode *inode, struct dir_entry_t *info) tm.day = info->ModifyTimestamp.Day; tm.mon = info->ModifyTimestamp.Month; tm.year = info->ModifyTimestamp.Year; - p_fs->fs_func->set_entry_time(ep, &tm, TM_MODIFY); + exfat_set_entry_time(ep, &tm, TM_MODIFY); - p_fs->fs_func->set_entry_size(ep2, info->Size); + exfat_set_entry_size(ep2, info->Size); update_dir_checksum_with_entry_set(sb, es); release_entry_set(es); @@ -1704,7 +1704,7 @@ static int ffsMapCluster(struct inode *inode, s32 clu_offset, u32 *clu) new_clu.flags = fid->flags; /* (1) allocate a cluster */ - num_alloced = p_fs->fs_func->alloc_cluster(sb, 1, &new_clu); + num_alloced = exfat_alloc_cluster(sb, 1, &new_clu); if (num_alloced < 0) { ret = -EIO; goto out; @@ -1744,13 +1744,11 @@ static int ffsMapCluster(struct inode *inode, s32 clu_offset, u32 *clu) /* (3) update directory entry */ if (modified) { - if (p_fs->fs_func->get_entry_flag(ep) != fid->flags) - p_fs->fs_func->set_entry_flag(ep, fid->flags); - - if (p_fs->fs_func->get_entry_clu0(ep) != fid->start_clu) - p_fs->fs_func->set_entry_clu0(ep, - fid->start_clu); + if (exfat_get_entry_flag(ep) != fid->flags) + exfat_set_entry_flag(ep, fid->flags); + if (exfat_get_entry_clu0(ep) != fid->start_clu) + exfat_set_entry_clu0(ep, fid->start_clu); } update_dir_checksum_with_entry_set(sb, es); @@ -1804,7 +1802,7 @@ static int ffsCreateDir(struct inode *inode, char *path, struct file_id_t *fid) ret = create_dir(inode, &dir, &uni_name, fid); -#ifndef CONFIG_EXFAT_DELAYED_SYNC +#ifndef CONFIG_STAGING_EXFAT_DELAYED_SYNC fs_sync(sb, true); fs_set_vol_flags(sb, VOL_CLEAN); #endif @@ -1831,7 +1829,6 @@ static int ffsReadDir(struct inode *inode, struct dir_entry_t *dir_entry) struct dentry_t *ep; struct super_block *sb = inode->i_sb; struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - struct fs_func *fs_func = p_fs->fs_func; struct file_id_t *fid = &(EXFAT_I(inode)->fid); /* check the validity of pointer parameters */ @@ -1913,7 +1910,7 @@ static int ffsReadDir(struct inode *inode, struct dir_entry_t *dir_entry) ret = -ENOENT; goto out; } - type = fs_func->get_entry_type(ep); + type = exfat_get_entry_type(ep); if (type == TYPE_UNUSED) break; @@ -1922,9 +1919,9 @@ static int ffsReadDir(struct inode *inode, struct dir_entry_t *dir_entry) continue; exfat_buf_lock(sb, sector); - dir_entry->Attr = fs_func->get_entry_attr(ep); + dir_entry->Attr = exfat_get_entry_attr(ep); - fs_func->get_entry_time(ep, &tm, TM_CREATE); + exfat_get_entry_time(ep, &tm, TM_CREATE); dir_entry->CreateTimestamp.Year = tm.year; dir_entry->CreateTimestamp.Month = tm.mon; dir_entry->CreateTimestamp.Day = tm.day; @@ -1933,7 +1930,7 @@ static int ffsReadDir(struct inode *inode, struct dir_entry_t *dir_entry) dir_entry->CreateTimestamp.Second = tm.sec; dir_entry->CreateTimestamp.MilliSecond = 0; - fs_func->get_entry_time(ep, &tm, TM_MODIFY); + exfat_get_entry_time(ep, &tm, TM_MODIFY); dir_entry->ModifyTimestamp.Year = tm.year; dir_entry->ModifyTimestamp.Month = tm.mon; dir_entry->ModifyTimestamp.Day = tm.day; @@ -1946,8 +1943,8 @@ static int ffsReadDir(struct inode *inode, struct dir_entry_t *dir_entry) sizeof(struct date_time_t)); *uni_name.name = 0x0; - fs_func->get_uni_name_from_ext_entry(sb, &dir, dentry, - uni_name.name); + exfat_get_uni_name_from_ext_entry(sb, &dir, dentry, + uni_name.name); nls_uniname_to_cstring(sb, dir_entry->Name, &uni_name); exfat_buf_unlock(sb, sector); @@ -1957,7 +1954,7 @@ static int ffsReadDir(struct inode *inode, struct dir_entry_t *dir_entry) goto out; } - dir_entry->Size = fs_func->get_entry_size(ep); + dir_entry->Size = exfat_get_entry_size(ep); /* hint information */ if (dir.dir == CLUSTER_32(0)) { /* FAT16 root_dir */ @@ -2047,13 +2044,13 @@ static int ffsRemoveDir(struct inode *inode, struct file_id_t *fid) remove_file(inode, &dir, dentry); /* (2) free the clusters */ - p_fs->fs_func->free_cluster(sb, &clu_to_free, 1); + exfat_free_cluster(sb, &clu_to_free, 1); fid->size = 0; fid->start_clu = CLUSTER_32(~0); fid->flags = (p_fs->vol_type == EXFAT) ? 0x03 : 0x01; -#ifndef CONFIG_EXFAT_DELAYED_SYNC +#ifndef CONFIG_STAGING_EXFAT_DELAYED_SYNC fs_sync(sb, true); fs_set_vol_flags(sb, VOL_CLEAN); #endif @@ -2176,14 +2173,14 @@ static long exfat_generic_ioctl(struct file *filp, unsigned int cmd, unsigned long arg) { struct inode *inode = filp->f_path.dentry->d_inode; -#ifdef CONFIG_EXFAT_KERNEL_DEBUG +#ifdef CONFIG_STAGING_EXFAT_KERNEL_DEBUG unsigned int flags; -#endif /* CONFIG_EXFAT_KERNEL_DEBUG */ +#endif /* CONFIG_STAGING_EXFAT_KERNEL_DEBUG */ switch (cmd) { case EXFAT_IOCTL_GET_VOLUME_ID: return exfat_ioctl_volume_id(inode); -#ifdef CONFIG_EXFAT_KERNEL_DEBUG +#ifdef CONFIG_STAGING_EXFAT_KERNEL_DEBUG case EXFAT_IOC_GET_DEBUGFLAGS: { struct super_block *sb = inode->i_sb; struct exfat_sb_info *sbi = EXFAT_SB(sb); @@ -2207,7 +2204,7 @@ static long exfat_generic_ioctl(struct file *filp, unsigned int cmd, return 0; } -#endif /* CONFIG_EXFAT_KERNEL_DEBUG */ +#endif /* CONFIG_STAGING_EXFAT_KERNEL_DEBUG */ default: return -ENOTTY; /* Inappropriate ioctl for device */ } @@ -3400,7 +3397,7 @@ static int exfat_show_options(struct seq_file *m, struct dentry *root) seq_puts(m, ",errors=panic"); else seq_puts(m, ",errors=remount-ro"); -#ifdef CONFIG_EXFAT_DISCARD +#ifdef CONFIG_STAGING_EXFAT_DISCARD if (opts->discard) seq_puts(m, ",discard"); #endif @@ -3481,7 +3478,7 @@ enum { Opt_err_ro, Opt_utf8_hack, Opt_err, -#ifdef CONFIG_EXFAT_DISCARD +#ifdef CONFIG_STAGING_EXFAT_DISCARD Opt_discard, #endif /* EXFAT_CONFIG_DISCARD */ }; @@ -3501,9 +3498,9 @@ static const match_table_t exfat_tokens = { {Opt_err_panic, "errors=panic"}, {Opt_err_ro, "errors=remount-ro"}, {Opt_utf8_hack, "utf8"}, -#ifdef CONFIG_EXFAT_DISCARD +#ifdef CONFIG_STAGING_EXFAT_DISCARD {Opt_discard, "discard"}, -#endif /* CONFIG_EXFAT_DISCARD */ +#endif /* CONFIG_STAGING_EXFAT_DISCARD */ {Opt_err, NULL} }; @@ -3524,7 +3521,7 @@ static int parse_options(char *options, int silent, int *debug, opts->iocharset = exfat_default_iocharset; opts->casesensitive = 0; opts->errors = EXFAT_ERRORS_RO; -#ifdef CONFIG_EXFAT_DISCARD +#ifdef CONFIG_STAGING_EXFAT_DISCARD opts->discard = 0; #endif *debug = 0; @@ -3595,11 +3592,11 @@ static int parse_options(char *options, int silent, int *debug, case Opt_debug: *debug = 1; break; -#ifdef CONFIG_EXFAT_DISCARD +#ifdef CONFIG_STAGING_EXFAT_DISCARD case Opt_discard: opts->discard = 1; break; -#endif /* CONFIG_EXFAT_DISCARD */ +#endif /* CONFIG_STAGING_EXFAT_DISCARD */ case Opt_utf8_hack: break; default: @@ -3803,7 +3800,7 @@ static void __exit exfat_destroy_inodecache(void) kmem_cache_destroy(exfat_inode_cachep); } -#ifdef CONFIG_EXFAT_KERNEL_DEBUG +#ifdef CONFIG_STAGING_EXFAT_KERNEL_DEBUG static void exfat_debug_kill_sb(struct super_block *sb) { struct exfat_sb_info *sbi = EXFAT_SB(sb); @@ -3831,17 +3828,17 @@ static void exfat_debug_kill_sb(struct super_block *sb) kill_block_super(sb); } -#endif /* CONFIG_EXFAT_KERNEL_DEBUG */ +#endif /* CONFIG_STAGING_EXFAT_KERNEL_DEBUG */ static struct file_system_type exfat_fs_type = { .owner = THIS_MODULE, .name = "exfat", .mount = exfat_fs_mount, -#ifdef CONFIG_EXFAT_KERNEL_DEBUG +#ifdef CONFIG_STAGING_EXFAT_KERNEL_DEBUG .kill_sb = exfat_debug_kill_sb, #else .kill_sb = kill_block_super, -#endif /* CONFIG_EXFAT_KERNEL_DEBUG */ +#endif /* CONFIG_STAGING_EXFAT_KERNEL_DEBUG */ .fs_flags = FS_REQUIRES_DEV, }; diff --git a/drivers/staging/hp/hp100.c b/drivers/staging/hp/hp100.c index 6ec78f5c602f..e2f0b58e5dfd 100644 --- a/drivers/staging/hp/hp100.c +++ b/drivers/staging/hp/hp100.c @@ -339,14 +339,11 @@ static __init int hp100_isa_probe1(struct net_device *dev, int ioaddr) if (sig == NULL) goto err; - for (i = 0; i < ARRAY_SIZE(hp100_isa_tbl); i++) { - if (!strcmp(hp100_isa_tbl[i], sig)) - break; - - } + i = match_string(hp100_isa_tbl, ARRAY_SIZE(hp100_isa_tbl), sig); + if (i < 0) + goto err; - if (i < ARRAY_SIZE(hp100_isa_tbl)) - return hp100_probe1(dev, ioaddr, HP100_BUS_ISA, NULL); + return hp100_probe1(dev, ioaddr, HP100_BUS_ISA, NULL); err: return -ENODEV; diff --git a/drivers/staging/iio/accel/adis16203.c b/drivers/staging/iio/accel/adis16203.c index 39687139a7d3..39dfe3f7f254 100644 --- a/drivers/staging/iio/accel/adis16203.c +++ b/drivers/staging/iio/accel/adis16203.c @@ -237,6 +237,12 @@ static const char * const adis16203_status_error_msgs[] = { [ADIS16203_DIAG_STAT_POWER_LOW_BIT] = "Power supply below 2.975V", }; +static const struct adis_timeout adis16203_timeouts = { + .reset_ms = ADIS16203_STARTUP_DELAY, + .sw_reset_ms = ADIS16203_STARTUP_DELAY, + .self_test_ms = ADIS16203_STARTUP_DELAY +}; + static const struct adis_data adis16203_data = { .read_delay = 20, .msc_ctrl_reg = ADIS16203_MSC_CTRL, @@ -245,7 +251,7 @@ static const struct adis_data adis16203_data = { .self_test_mask = ADIS16203_MSC_CTRL_SELF_TEST_EN, .self_test_no_autoclear = true, - .startup_delay = ADIS16203_STARTUP_DELAY, + .timeouts = &adis16203_timeouts, .status_error_msgs = adis16203_status_error_msgs, .status_error_mask = BIT(ADIS16203_DIAG_STAT_SELFTEST_FAIL_BIT) | diff --git a/drivers/staging/iio/accel/adis16240.c b/drivers/staging/iio/accel/adis16240.c index a480409090c0..39eb8364aa95 100644 --- a/drivers/staging/iio/accel/adis16240.c +++ b/drivers/staging/iio/accel/adis16240.c @@ -359,6 +359,12 @@ static const char * const adis16240_status_error_msgs[] = { [ADIS16240_DIAG_STAT_POWER_LOW_BIT] = "Power supply below 2.225V", }; +static const struct adis_timeout adis16240_timeouts = { + .reset_ms = ADIS16240_STARTUP_DELAY, + .sw_reset_ms = ADIS16240_STARTUP_DELAY, + .self_test_ms = ADIS16240_STARTUP_DELAY, +}; + static const struct adis_data adis16240_data = { .write_delay = 35, .read_delay = 35, @@ -368,7 +374,7 @@ static const struct adis_data adis16240_data = { .self_test_mask = ADIS16240_MSC_CTRL_SELF_TEST_EN, .self_test_no_autoclear = true, - .startup_delay = ADIS16240_STARTUP_DELAY, + .timeouts = &adis16240_timeouts, .status_error_msgs = adis16240_status_error_msgs, .status_error_mask = BIT(ADIS16240_DIAG_STAT_PWRON_FAIL_BIT) | @@ -399,6 +405,13 @@ static int adis16240_probe(struct spi_device *spi) indio_dev->num_channels = ARRAY_SIZE(adis16240_channels); indio_dev->modes = INDIO_DIRECT_MODE; + spi->mode = SPI_MODE_3; + ret = spi_setup(spi); + if (ret) { + dev_err(&spi->dev, "spi_setup failed!\n"); + return ret; + } + ret = adis_init(st, indio_dev, spi, &adis16240_data); if (ret) return ret; diff --git a/drivers/staging/isdn/Kconfig b/drivers/staging/isdn/Kconfig deleted file mode 100644 index faaf63887094..000000000000 --- a/drivers/staging/isdn/Kconfig +++ /dev/null @@ -1,12 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0-only -menu "ISDN CAPI drivers" - depends on ISDN_CAPI - -source "drivers/staging/isdn/avm/Kconfig" - -source "drivers/staging/isdn/gigaset/Kconfig" - -source "drivers/staging/isdn/hysdn/Kconfig" - -endmenu - diff --git a/drivers/staging/isdn/Makefile b/drivers/staging/isdn/Makefile deleted file mode 100644 index 025504bae5df..000000000000 --- a/drivers/staging/isdn/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0 -# Makefile for the kernel ISDN subsystem and device drivers. - -# Object files in subdirectories - -obj-$(CONFIG_CAPI_AVM) += avm/ -obj-$(CONFIG_HYSDN) += hysdn/ -obj-$(CONFIG_ISDN_DRV_GIGASET) += gigaset/ diff --git a/drivers/staging/isdn/TODO b/drivers/staging/isdn/TODO deleted file mode 100644 index 9210d11eb68b..000000000000 --- a/drivers/staging/isdn/TODO +++ /dev/null @@ -1,22 +0,0 @@ -TODO: Remove in late 2019 unless there are users - - -I tried to find any indication of whether the capi drivers are -still in use, and have not found anything from a long time ago. - -With public ISDN networks almost completely shut down over the past 12 -months, there is very little you can actually do with this hardware. The -main remaining use case would be to connect ISDN voice phones to an -in-house installation with Asterisk or LCR, but anyone trying this in -turn seems to be using either the mISDN driver stack, or out-of-tree -drivers from the hardware vendors. - -I may of course have missed something, so I would suggest moving -these into drivers/staging/ just in case someone still uses one -of the three remaining in-kernel drivers (avm, hysdn, gigaset). - -If nobody complains, we can remove them entirely in six months, -or otherwise move the core code and any drivers that are still -needed back into drivers/isdn. - - Arnd Bergmann <arnd@arndb.de> diff --git a/drivers/staging/isdn/avm/Kconfig b/drivers/staging/isdn/avm/Kconfig deleted file mode 100644 index 81483db067bb..000000000000 --- a/drivers/staging/isdn/avm/Kconfig +++ /dev/null @@ -1,65 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0-only -# -# ISDN AVM drivers -# - -menuconfig CAPI_AVM - bool "Active AVM cards" - help - Enable support for AVM active ISDN cards. - -if CAPI_AVM - -config ISDN_DRV_AVMB1_B1ISA - tristate "AVM B1 ISA support" - depends on ISA - help - Enable support for the ISA version of the AVM B1 card. - -config ISDN_DRV_AVMB1_B1PCI - tristate "AVM B1 PCI support" - depends on PCI - help - Enable support for the PCI version of the AVM B1 card. - -config ISDN_DRV_AVMB1_B1PCIV4 - bool "AVM B1 PCI V4 support" - depends on ISDN_DRV_AVMB1_B1PCI - help - Enable support for the V4 version of AVM B1 PCI card. - -config ISDN_DRV_AVMB1_T1ISA - tristate "AVM T1/T1-B ISA support" - depends on ISA - help - Enable support for the AVM T1 T1B card. - Note: This is a PRI card and handle 30 B-channels. - -config ISDN_DRV_AVMB1_B1PCMCIA - tristate "AVM B1/M1/M2 PCMCIA support" - depends on PCMCIA - help - Enable support for the PCMCIA version of the AVM B1 card. - -config ISDN_DRV_AVMB1_AVM_CS - tristate "AVM B1/M1/M2 PCMCIA cs module" - depends on ISDN_DRV_AVMB1_B1PCMCIA - help - Enable the PCMCIA client driver for the AVM B1/M1/M2 - PCMCIA cards. - -config ISDN_DRV_AVMB1_T1PCI - tristate "AVM T1/T1-B PCI support" - depends on PCI - help - Enable support for the AVM T1 T1B card. - Note: This is a PRI card and handle 30 B-channels. - -config ISDN_DRV_AVMB1_C4 - tristate "AVM C4/C2 support" - depends on PCI - help - Enable support for the AVM C4/C2 PCI cards. - These cards handle 4/2 BRI ISDN lines (8/4 channels). - -endif # CAPI_AVM diff --git a/drivers/staging/isdn/avm/Makefile b/drivers/staging/isdn/avm/Makefile deleted file mode 100644 index 3830a0573fcc..000000000000 --- a/drivers/staging/isdn/avm/Makefile +++ /dev/null @@ -1,12 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0 -# Makefile for the AVM ISDN device drivers - -# Each configuration option enables a list of files. - -obj-$(CONFIG_ISDN_DRV_AVMB1_B1ISA) += b1isa.o b1.o -obj-$(CONFIG_ISDN_DRV_AVMB1_B1PCI) += b1pci.o b1.o b1dma.o -obj-$(CONFIG_ISDN_DRV_AVMB1_B1PCMCIA) += b1pcmcia.o b1.o -obj-$(CONFIG_ISDN_DRV_AVMB1_AVM_CS) += avm_cs.o -obj-$(CONFIG_ISDN_DRV_AVMB1_T1ISA) += t1isa.o b1.o -obj-$(CONFIG_ISDN_DRV_AVMB1_T1PCI) += t1pci.o b1.o b1dma.o -obj-$(CONFIG_ISDN_DRV_AVMB1_C4) += c4.o b1.o diff --git a/drivers/staging/isdn/avm/avm_cs.c b/drivers/staging/isdn/avm/avm_cs.c deleted file mode 100644 index 62b8030ee331..000000000000 --- a/drivers/staging/isdn/avm/avm_cs.c +++ /dev/null @@ -1,166 +0,0 @@ -/* $Id: avm_cs.c,v 1.4.6.3 2001/09/23 22:24:33 kai Exp $ - * - * A PCMCIA client driver for AVM B1/M1/M2 - * - * Copyright 1999 by Carsten Paeth <calle@calle.de> - * - * This software may be used and distributed according to the terms - * of the GNU General Public License, incorporated herein by reference. - * - */ - -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/ptrace.h> -#include <linux/string.h> -#include <linux/tty.h> -#include <linux/serial.h> -#include <linux/major.h> -#include <asm/io.h> - -#include <pcmcia/cistpl.h> -#include <pcmcia/ciscode.h> -#include <pcmcia/ds.h> -#include <pcmcia/cisreg.h> - -#include <linux/skbuff.h> -#include <linux/capi.h> -#include <linux/b1lli.h> -#include <linux/b1pcmcia.h> - -/*====================================================================*/ - -MODULE_DESCRIPTION("CAPI4Linux: PCMCIA client driver for AVM B1/M1/M2"); -MODULE_AUTHOR("Carsten Paeth"); -MODULE_LICENSE("GPL"); - -/*====================================================================*/ - -static int avmcs_config(struct pcmcia_device *link); -static void avmcs_release(struct pcmcia_device *link); -static void avmcs_detach(struct pcmcia_device *p_dev); - -static int avmcs_probe(struct pcmcia_device *p_dev) -{ - /* General socket configuration */ - p_dev->config_flags |= CONF_ENABLE_IRQ | CONF_AUTO_SET_IO; - p_dev->config_index = 1; - p_dev->config_regs = PRESENT_OPTION; - - return avmcs_config(p_dev); -} /* avmcs_attach */ - - -static void avmcs_detach(struct pcmcia_device *link) -{ - avmcs_release(link); -} /* avmcs_detach */ - -static int avmcs_configcheck(struct pcmcia_device *p_dev, void *priv_data) -{ - p_dev->resource[0]->end = 16; - p_dev->resource[0]->flags &= ~IO_DATA_PATH_WIDTH; - p_dev->resource[0]->flags |= IO_DATA_PATH_WIDTH_8; - - return pcmcia_request_io(p_dev); -} - -static int avmcs_config(struct pcmcia_device *link) -{ - int i = -1; - char devname[128]; - int cardtype; - int (*addcard)(unsigned int port, unsigned irq); - - devname[0] = 0; - if (link->prod_id[1]) - strlcpy(devname, link->prod_id[1], sizeof(devname)); - - /* - * find IO port - */ - if (pcmcia_loop_config(link, avmcs_configcheck, NULL)) - return -ENODEV; - - do { - if (!link->irq) { - /* undo */ - pcmcia_disable_device(link); - break; - } - - /* - * configure the PCMCIA socket - */ - i = pcmcia_enable_device(link); - if (i != 0) { - pcmcia_disable_device(link); - break; - } - - } while (0); - - if (devname[0]) { - char *s = strrchr(devname, ' '); - if (!s) - s = devname; - else s++; - if (strcmp("M1", s) == 0) { - cardtype = AVM_CARDTYPE_M1; - } else if (strcmp("M2", s) == 0) { - cardtype = AVM_CARDTYPE_M2; - } else { - cardtype = AVM_CARDTYPE_B1; - } - } else - cardtype = AVM_CARDTYPE_B1; - - /* If any step failed, release any partially configured state */ - if (i != 0) { - avmcs_release(link); - return -ENODEV; - } - - - switch (cardtype) { - case AVM_CARDTYPE_M1: addcard = b1pcmcia_addcard_m1; break; - case AVM_CARDTYPE_M2: addcard = b1pcmcia_addcard_m2; break; - default: - case AVM_CARDTYPE_B1: addcard = b1pcmcia_addcard_b1; break; - } - if ((i = (*addcard)(link->resource[0]->start, link->irq)) < 0) { - dev_err(&link->dev, - "avm_cs: failed to add AVM-Controller at i/o %#x, irq %d\n", - (unsigned int) link->resource[0]->start, link->irq); - avmcs_release(link); - return -ENODEV; - } - return 0; - -} /* avmcs_config */ - - -static void avmcs_release(struct pcmcia_device *link) -{ - b1pcmcia_delcard(link->resource[0]->start, link->irq); - pcmcia_disable_device(link); -} /* avmcs_release */ - - -static const struct pcmcia_device_id avmcs_ids[] = { - PCMCIA_DEVICE_PROD_ID12("AVM", "ISDN-Controller B1", 0x95d42008, 0x845dc335), - PCMCIA_DEVICE_PROD_ID12("AVM", "Mobile ISDN-Controller M1", 0x95d42008, 0x81e10430), - PCMCIA_DEVICE_PROD_ID12("AVM", "Mobile ISDN-Controller M2", 0x95d42008, 0x18e8558a), - PCMCIA_DEVICE_NULL -}; -MODULE_DEVICE_TABLE(pcmcia, avmcs_ids); - -static struct pcmcia_driver avmcs_driver = { - .owner = THIS_MODULE, - .name = "avm_cs", - .probe = avmcs_probe, - .remove = avmcs_detach, - .id_table = avmcs_ids, -}; -module_pcmcia_driver(avmcs_driver); diff --git a/drivers/staging/isdn/avm/avmcard.h b/drivers/staging/isdn/avm/avmcard.h deleted file mode 100644 index cdfa89c71997..000000000000 --- a/drivers/staging/isdn/avm/avmcard.h +++ /dev/null @@ -1,581 +0,0 @@ -/* $Id: avmcard.h,v 1.1.4.1.2.1 2001/12/21 15:00:17 kai Exp $ - * - * Copyright 1999 by Carsten Paeth <calle@calle.de> - * - * This software may be used and distributed according to the terms - * of the GNU General Public License, incorporated herein by reference. - * - */ - -#ifndef _AVMCARD_H_ -#define _AVMCARD_H_ - -#include <linux/spinlock.h> -#include <linux/list.h> -#include <linux/interrupt.h> - -#define AVMB1_PORTLEN 0x1f -#define AVM_MAXVERSION 8 -#define AVM_NCCI_PER_CHANNEL 4 - -/* - * Versions - */ - -#define VER_DRIVER 0 -#define VER_CARDTYPE 1 -#define VER_HWID 2 -#define VER_SERIAL 3 -#define VER_OPTION 4 -#define VER_PROTO 5 -#define VER_PROFILE 6 -#define VER_CAPI 7 - -enum avmcardtype { - avm_b1isa, - avm_b1pci, - avm_b1pcmcia, - avm_m1, - avm_m2, - avm_t1isa, - avm_t1pci, - avm_c4, - avm_c2 -}; - -typedef struct avmcard_dmabuf { - long size; - u8 *dmabuf; - dma_addr_t dmaaddr; -} avmcard_dmabuf; - -typedef struct avmcard_dmainfo { - u32 recvlen; - avmcard_dmabuf recvbuf; - - avmcard_dmabuf sendbuf; - struct sk_buff_head send_queue; - - struct pci_dev *pcidev; -} avmcard_dmainfo; - -typedef struct avmctrl_info { - char cardname[32]; - - int versionlen; - char versionbuf[1024]; - char *version[AVM_MAXVERSION]; - - char infobuf[128]; /* for function procinfo */ - - struct avmcard *card; - struct capi_ctr capi_ctrl; - - struct list_head ncci_head; -} avmctrl_info; - -typedef struct avmcard { - char name[32]; - - spinlock_t lock; - unsigned int port; - unsigned irq; - unsigned long membase; - enum avmcardtype cardtype; - unsigned char revision; - unsigned char class; - int cardnr; /* for t1isa */ - - char msgbuf[128]; /* capimsg msg part */ - char databuf[2048]; /* capimsg data part */ - - void __iomem *mbase; - volatile u32 csr; - avmcard_dmainfo *dma; - - struct avmctrl_info *ctrlinfo; - - u_int nr_controllers; - u_int nlogcontr; - struct list_head list; -} avmcard; - -extern int b1_irq_table[16]; - -/* - * LLI Messages to the ISDN-ControllerISDN Controller - */ - -#define SEND_POLL 0x72 /* - * after load <- RECEIVE_POLL - */ -#define SEND_INIT 0x11 /* - * first message <- RECEIVE_INIT - * int32 NumApplications int32 - * NumNCCIs int32 BoardNumber - */ -#define SEND_REGISTER 0x12 /* - * register an application int32 - * ApplIDId int32 NumMessages - * int32 NumB3Connections int32 - * NumB3Blocks int32 B3Size - * - * AnzB3Connection != 0 && - * AnzB3Blocks >= 1 && B3Size >= 1 - */ -#define SEND_RELEASE 0x14 /* - * deregister an application int32 - * ApplID - */ -#define SEND_MESSAGE 0x15 /* - * send capi-message int32 length - * capi-data ... - */ -#define SEND_DATA_B3_REQ 0x13 /* - * send capi-data-message int32 - * MsgLength capi-data ... int32 - * B3Length data .... - */ - -#define SEND_CONFIG 0x21 /* - */ - -#define SEND_POLLACK 0x73 /* T1 Watchdog */ - -/* - * LLI Messages from the ISDN-ControllerISDN Controller - */ - -#define RECEIVE_POLL 0x32 /* - * <- after SEND_POLL - */ -#define RECEIVE_INIT 0x27 /* - * <- after SEND_INIT int32 length - * byte total length b1struct board - * driver revision b1struct card - * type b1struct reserved b1struct - * serial number b1struct driver - * capability b1struct d-channel - * protocol b1struct CAPI-2.0 - * profile b1struct capi version - */ -#define RECEIVE_MESSAGE 0x21 /* - * <- after SEND_MESSAGE int32 - * AppllID int32 Length capi-data - * .... - */ -#define RECEIVE_DATA_B3_IND 0x22 /* - * received data int32 AppllID - * int32 Length capi-data ... - * int32 B3Length data ... - */ -#define RECEIVE_START 0x23 /* - * Handshake - */ -#define RECEIVE_STOP 0x24 /* - * Handshake - */ -#define RECEIVE_NEW_NCCI 0x25 /* - * int32 AppllID int32 NCCI int32 - * WindowSize - */ -#define RECEIVE_FREE_NCCI 0x26 /* - * int32 AppllID int32 NCCI - */ -#define RECEIVE_RELEASE 0x26 /* - * int32 AppllID int32 0xffffffff - */ -#define RECEIVE_TASK_READY 0x31 /* - * int32 tasknr - * int32 Length Taskname ... - */ -#define RECEIVE_DEBUGMSG 0x71 /* - * int32 Length message - * - */ -#define RECEIVE_POLLDWORD 0x75 /* t1pci in dword mode */ - -#define WRITE_REGISTER 0x00 -#define READ_REGISTER 0x01 - -/* - * port offsets - */ - -#define B1_READ 0x00 -#define B1_WRITE 0x01 -#define B1_INSTAT 0x02 -#define B1_OUTSTAT 0x03 -#define B1_ANALYSE 0x04 -#define B1_REVISION 0x05 -#define B1_RESET 0x10 - - -#define B1_STAT0(cardtype) ((cardtype) == avm_m1 ? 0x81200000l : 0x80A00000l) -#define B1_STAT1(cardtype) (0x80E00000l) - -/* ---------------------------------------------------------------- */ - -static inline unsigned char b1outp(unsigned int base, - unsigned short offset, - unsigned char value) -{ - outb(value, base + offset); - return inb(base + B1_ANALYSE); -} - - -static inline int b1_rx_full(unsigned int base) -{ - return inb(base + B1_INSTAT) & 0x1; -} - -static inline unsigned char b1_get_byte(unsigned int base) -{ - unsigned long stop = jiffies + 1 * HZ; /* maximum wait time 1 sec */ - while (!b1_rx_full(base) && time_before(jiffies, stop)); - if (b1_rx_full(base)) - return inb(base + B1_READ); - printk(KERN_CRIT "b1lli(0x%x): rx not full after 1 second\n", base); - return 0; -} - -static inline unsigned int b1_get_word(unsigned int base) -{ - unsigned int val = 0; - val |= b1_get_byte(base); - val |= (b1_get_byte(base) << 8); - val |= (b1_get_byte(base) << 16); - val |= (b1_get_byte(base) << 24); - return val; -} - -static inline int b1_tx_empty(unsigned int base) -{ - return inb(base + B1_OUTSTAT) & 0x1; -} - -static inline void b1_put_byte(unsigned int base, unsigned char val) -{ - while (!b1_tx_empty(base)); - b1outp(base, B1_WRITE, val); -} - -static inline int b1_save_put_byte(unsigned int base, unsigned char val) -{ - unsigned long stop = jiffies + 2 * HZ; - while (!b1_tx_empty(base) && time_before(jiffies, stop)); - if (!b1_tx_empty(base)) return -1; - b1outp(base, B1_WRITE, val); - return 0; -} - -static inline void b1_put_word(unsigned int base, unsigned int val) -{ - b1_put_byte(base, val & 0xff); - b1_put_byte(base, (val >> 8) & 0xff); - b1_put_byte(base, (val >> 16) & 0xff); - b1_put_byte(base, (val >> 24) & 0xff); -} - -static inline unsigned int b1_get_slice(unsigned int base, - unsigned char *dp) -{ - unsigned int len, i; - - len = i = b1_get_word(base); - while (i-- > 0) *dp++ = b1_get_byte(base); - return len; -} - -static inline void b1_put_slice(unsigned int base, - unsigned char *dp, unsigned int len) -{ - unsigned i = len; - b1_put_word(base, i); - while (i-- > 0) - b1_put_byte(base, *dp++); -} - -static void b1_wr_reg(unsigned int base, - unsigned int reg, - unsigned int value) -{ - b1_put_byte(base, WRITE_REGISTER); - b1_put_word(base, reg); - b1_put_word(base, value); -} - -static inline unsigned int b1_rd_reg(unsigned int base, - unsigned int reg) -{ - b1_put_byte(base, READ_REGISTER); - b1_put_word(base, reg); - return b1_get_word(base); - -} - -static inline void b1_reset(unsigned int base) -{ - b1outp(base, B1_RESET, 0); - mdelay(55 * 2); /* 2 TIC's */ - - b1outp(base, B1_RESET, 1); - mdelay(55 * 2); /* 2 TIC's */ - - b1outp(base, B1_RESET, 0); - mdelay(55 * 2); /* 2 TIC's */ -} - -static inline unsigned char b1_disable_irq(unsigned int base) -{ - return b1outp(base, B1_INSTAT, 0x00); -} - -/* ---------------------------------------------------------------- */ - -static inline void b1_set_test_bit(unsigned int base, - enum avmcardtype cardtype, - int onoff) -{ - b1_wr_reg(base, B1_STAT0(cardtype), onoff ? 0x21 : 0x20); -} - -static inline int b1_get_test_bit(unsigned int base, - enum avmcardtype cardtype) -{ - return (b1_rd_reg(base, B1_STAT0(cardtype)) & 0x01) != 0; -} - -/* ---------------------------------------------------------------- */ - -#define T1_FASTLINK 0x00 -#define T1_SLOWLINK 0x08 - -#define T1_READ B1_READ -#define T1_WRITE B1_WRITE -#define T1_INSTAT B1_INSTAT -#define T1_OUTSTAT B1_OUTSTAT -#define T1_IRQENABLE 0x05 -#define T1_FIFOSTAT 0x06 -#define T1_RESETLINK 0x10 -#define T1_ANALYSE 0x11 -#define T1_IRQMASTER 0x12 -#define T1_IDENT 0x17 -#define T1_RESETBOARD 0x1f - -#define T1F_IREADY 0x01 -#define T1F_IHALF 0x02 -#define T1F_IFULL 0x04 -#define T1F_IEMPTY 0x08 -#define T1F_IFLAGS 0xF0 - -#define T1F_OREADY 0x10 -#define T1F_OHALF 0x20 -#define T1F_OEMPTY 0x40 -#define T1F_OFULL 0x80 -#define T1F_OFLAGS 0xF0 - -/* there are HEMA cards with 1k and 4k FIFO out */ -#define FIFO_OUTBSIZE 256 -#define FIFO_INPBSIZE 512 - -#define HEMA_VERSION_ID 0 -#define HEMA_PAL_ID 0 - -static inline void t1outp(unsigned int base, - unsigned short offset, - unsigned char value) -{ - outb(value, base + offset); -} - -static inline unsigned char t1inp(unsigned int base, - unsigned short offset) -{ - return inb(base + offset); -} - -static inline int t1_isfastlink(unsigned int base) -{ - return (inb(base + T1_IDENT) & ~0x82) == 1; -} - -static inline unsigned char t1_fifostatus(unsigned int base) -{ - return inb(base + T1_FIFOSTAT); -} - -static inline unsigned int t1_get_slice(unsigned int base, - unsigned char *dp) -{ - unsigned int len, i; -#ifdef FASTLINK_DEBUG - unsigned wcnt = 0, bcnt = 0; -#endif - - len = i = b1_get_word(base); - if (t1_isfastlink(base)) { - int status; - while (i > 0) { - status = t1_fifostatus(base) & (T1F_IREADY | T1F_IHALF); - if (i >= FIFO_INPBSIZE) status |= T1F_IFULL; - - switch (status) { - case T1F_IREADY | T1F_IHALF | T1F_IFULL: - insb(base + B1_READ, dp, FIFO_INPBSIZE); - dp += FIFO_INPBSIZE; - i -= FIFO_INPBSIZE; -#ifdef FASTLINK_DEBUG - wcnt += FIFO_INPBSIZE; -#endif - break; - case T1F_IREADY | T1F_IHALF: - insb(base + B1_READ, dp, i); -#ifdef FASTLINK_DEBUG - wcnt += i; -#endif - dp += i; - i = 0; - break; - default: - *dp++ = b1_get_byte(base); - i--; -#ifdef FASTLINK_DEBUG - bcnt++; -#endif - break; - } - } -#ifdef FASTLINK_DEBUG - if (wcnt) - printk(KERN_DEBUG "b1lli(0x%x): get_slice l=%d w=%d b=%d\n", - base, len, wcnt, bcnt); -#endif - } else { - while (i-- > 0) - *dp++ = b1_get_byte(base); - } - return len; -} - -static inline void t1_put_slice(unsigned int base, - unsigned char *dp, unsigned int len) -{ - unsigned i = len; - b1_put_word(base, i); - if (t1_isfastlink(base)) { - int status; - while (i > 0) { - status = t1_fifostatus(base) & (T1F_OREADY | T1F_OHALF); - if (i >= FIFO_OUTBSIZE) status |= T1F_OEMPTY; - switch (status) { - case T1F_OREADY | T1F_OHALF | T1F_OEMPTY: - outsb(base + B1_WRITE, dp, FIFO_OUTBSIZE); - dp += FIFO_OUTBSIZE; - i -= FIFO_OUTBSIZE; - break; - case T1F_OREADY | T1F_OHALF: - outsb(base + B1_WRITE, dp, i); - dp += i; - i = 0; - break; - default: - b1_put_byte(base, *dp++); - i--; - break; - } - } - } else { - while (i-- > 0) - b1_put_byte(base, *dp++); - } -} - -static inline void t1_disable_irq(unsigned int base) -{ - t1outp(base, T1_IRQMASTER, 0x00); -} - -static inline void t1_reset(unsigned int base) -{ - /* reset T1 Controller */ - b1_reset(base); - /* disable irq on HEMA */ - t1outp(base, B1_INSTAT, 0x00); - t1outp(base, B1_OUTSTAT, 0x00); - t1outp(base, T1_IRQMASTER, 0x00); - /* reset HEMA board configuration */ - t1outp(base, T1_RESETBOARD, 0xf); -} - -static inline void b1_setinterrupt(unsigned int base, unsigned irq, - enum avmcardtype cardtype) -{ - switch (cardtype) { - case avm_t1isa: - t1outp(base, B1_INSTAT, 0x00); - t1outp(base, B1_INSTAT, 0x02); - t1outp(base, T1_IRQMASTER, 0x08); - break; - case avm_b1isa: - b1outp(base, B1_INSTAT, 0x00); - b1outp(base, B1_RESET, b1_irq_table[irq]); - b1outp(base, B1_INSTAT, 0x02); - break; - default: - case avm_m1: - case avm_m2: - case avm_b1pci: - b1outp(base, B1_INSTAT, 0x00); - b1outp(base, B1_RESET, 0xf0); - b1outp(base, B1_INSTAT, 0x02); - break; - case avm_c4: - case avm_t1pci: - b1outp(base, B1_RESET, 0xf0); - break; - } -} - -/* b1.c */ -avmcard *b1_alloc_card(int nr_controllers); -void b1_free_card(avmcard *card); -int b1_detect(unsigned int base, enum avmcardtype cardtype); -void b1_getrevision(avmcard *card); -int b1_load_t4file(avmcard *card, capiloaddatapart *t4file); -int b1_load_config(avmcard *card, capiloaddatapart *config); -int b1_loaded(avmcard *card); - -int b1_load_firmware(struct capi_ctr *ctrl, capiloaddata *data); -void b1_reset_ctr(struct capi_ctr *ctrl); -void b1_register_appl(struct capi_ctr *ctrl, u16 appl, - capi_register_params *rp); -void b1_release_appl(struct capi_ctr *ctrl, u16 appl); -u16 b1_send_message(struct capi_ctr *ctrl, struct sk_buff *skb); -void b1_parse_version(avmctrl_info *card); -irqreturn_t b1_interrupt(int interrupt, void *devptr); - -int b1_proc_show(struct seq_file *m, void *v); - -avmcard_dmainfo *avmcard_dma_alloc(char *name, struct pci_dev *, - long rsize, long ssize); -void avmcard_dma_free(avmcard_dmainfo *); - -/* b1dma.c */ -int b1pciv4_detect(avmcard *card); -int t1pci_detect(avmcard *card); -void b1dma_reset(avmcard *card); -irqreturn_t b1dma_interrupt(int interrupt, void *devptr); - -int b1dma_load_firmware(struct capi_ctr *ctrl, capiloaddata *data); -void b1dma_reset_ctr(struct capi_ctr *ctrl); -void b1dma_remove_ctr(struct capi_ctr *ctrl); -void b1dma_register_appl(struct capi_ctr *ctrl, - u16 appl, - capi_register_params *rp); -void b1dma_release_appl(struct capi_ctr *ctrl, u16 appl); -u16 b1dma_send_message(struct capi_ctr *ctrl, struct sk_buff *skb); -int b1dma_proc_show(struct seq_file *m, void *v); - -#endif /* _AVMCARD_H_ */ diff --git a/drivers/staging/isdn/avm/b1.c b/drivers/staging/isdn/avm/b1.c deleted file mode 100644 index 32ec8cf31fd0..000000000000 --- a/drivers/staging/isdn/avm/b1.c +++ /dev/null @@ -1,819 +0,0 @@ -/* $Id: b1.c,v 1.1.2.2 2004/01/16 21:09:27 keil Exp $ - * - * Common module for AVM B1 cards. - * - * Copyright 1999 by Carsten Paeth <calle@calle.de> - * - * This software may be used and distributed according to the terms - * of the GNU General Public License, incorporated herein by reference. - * - */ - -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/pci.h> -#include <linux/proc_fs.h> -#include <linux/seq_file.h> -#include <linux/skbuff.h> -#include <linux/delay.h> -#include <linux/mm.h> -#include <linux/interrupt.h> -#include <linux/ioport.h> -#include <linux/capi.h> -#include <linux/kernelcapi.h> -#include <linux/slab.h> -#include <asm/io.h> -#include <linux/init.h> -#include <linux/uaccess.h> -#include <linux/netdevice.h> -#include <linux/isdn/capilli.h> -#include "avmcard.h" -#include <linux/isdn/capicmd.h> -#include <linux/isdn/capiutil.h> - -static char *revision = "$Revision: 1.1.2.2 $"; - -/* ------------------------------------------------------------- */ - -MODULE_DESCRIPTION("CAPI4Linux: Common support for active AVM cards"); -MODULE_AUTHOR("Carsten Paeth"); -MODULE_LICENSE("GPL"); - -/* ------------------------------------------------------------- */ - -int b1_irq_table[16] = -{0, - 0, - 0, - 192, /* irq 3 */ - 32, /* irq 4 */ - 160, /* irq 5 */ - 96, /* irq 6 */ - 224, /* irq 7 */ - 0, - 64, /* irq 9 */ - 80, /* irq 10 */ - 208, /* irq 11 */ - 48, /* irq 12 */ - 0, - 0, - 112, /* irq 15 */ -}; - -/* ------------------------------------------------------------- */ - -avmcard *b1_alloc_card(int nr_controllers) -{ - avmcard *card; - avmctrl_info *cinfo; - int i; - - card = kzalloc(sizeof(*card), GFP_KERNEL); - if (!card) - return NULL; - - cinfo = kcalloc(nr_controllers, sizeof(*cinfo), GFP_KERNEL); - if (!cinfo) { - kfree(card); - return NULL; - } - - card->ctrlinfo = cinfo; - for (i = 0; i < nr_controllers; i++) { - INIT_LIST_HEAD(&cinfo[i].ncci_head); - cinfo[i].card = card; - } - spin_lock_init(&card->lock); - card->nr_controllers = nr_controllers; - - return card; -} - -/* ------------------------------------------------------------- */ - -void b1_free_card(avmcard *card) -{ - kfree(card->ctrlinfo); - kfree(card); -} - -/* ------------------------------------------------------------- */ - -int b1_detect(unsigned int base, enum avmcardtype cardtype) -{ - int onoff, i; - - /* - * Statusregister 0000 00xx - */ - if ((inb(base + B1_INSTAT) & 0xfc) - || (inb(base + B1_OUTSTAT) & 0xfc)) - return 1; - /* - * Statusregister 0000 001x - */ - b1outp(base, B1_INSTAT, 0x2); /* enable irq */ - /* b1outp(base, B1_OUTSTAT, 0x2); */ - if ((inb(base + B1_INSTAT) & 0xfe) != 0x2 - /* || (inb(base + B1_OUTSTAT) & 0xfe) != 0x2 */) - return 2; - /* - * Statusregister 0000 000x - */ - b1outp(base, B1_INSTAT, 0x0); /* disable irq */ - b1outp(base, B1_OUTSTAT, 0x0); - if ((inb(base + B1_INSTAT) & 0xfe) - || (inb(base + B1_OUTSTAT) & 0xfe)) - return 3; - - for (onoff = !0, i = 0; i < 10; i++) { - b1_set_test_bit(base, cardtype, onoff); - if (b1_get_test_bit(base, cardtype) != onoff) - return 4; - onoff = !onoff; - } - - if (cardtype == avm_m1) - return 0; - - if ((b1_rd_reg(base, B1_STAT1(cardtype)) & 0x0f) != 0x01) - return 5; - - return 0; -} - -void b1_getrevision(avmcard *card) -{ - card->class = inb(card->port + B1_ANALYSE); - card->revision = inb(card->port + B1_REVISION); -} - -#define FWBUF_SIZE 256 -int b1_load_t4file(avmcard *card, capiloaddatapart *t4file) -{ - unsigned char buf[FWBUF_SIZE]; - unsigned char *dp; - int i, left; - unsigned int base = card->port; - - dp = t4file->data; - left = t4file->len; - while (left > FWBUF_SIZE) { - if (t4file->user) { - if (copy_from_user(buf, dp, FWBUF_SIZE)) - return -EFAULT; - } else { - memcpy(buf, dp, FWBUF_SIZE); - } - for (i = 0; i < FWBUF_SIZE; i++) - if (b1_save_put_byte(base, buf[i]) < 0) { - printk(KERN_ERR "%s: corrupted firmware file ?\n", - card->name); - return -EIO; - } - left -= FWBUF_SIZE; - dp += FWBUF_SIZE; - } - if (left) { - if (t4file->user) { - if (copy_from_user(buf, dp, left)) - return -EFAULT; - } else { - memcpy(buf, dp, left); - } - for (i = 0; i < left; i++) - if (b1_save_put_byte(base, buf[i]) < 0) { - printk(KERN_ERR "%s: corrupted firmware file ?\n", - card->name); - return -EIO; - } - } - return 0; -} - -int b1_load_config(avmcard *card, capiloaddatapart *config) -{ - unsigned char buf[FWBUF_SIZE]; - unsigned char *dp; - unsigned int base = card->port; - int i, j, left; - - dp = config->data; - left = config->len; - if (left) { - b1_put_byte(base, SEND_CONFIG); - b1_put_word(base, 1); - b1_put_byte(base, SEND_CONFIG); - b1_put_word(base, left); - } - while (left > FWBUF_SIZE) { - if (config->user) { - if (copy_from_user(buf, dp, FWBUF_SIZE)) - return -EFAULT; - } else { - memcpy(buf, dp, FWBUF_SIZE); - } - for (i = 0; i < FWBUF_SIZE; ) { - b1_put_byte(base, SEND_CONFIG); - for (j = 0; j < 4; j++) { - b1_put_byte(base, buf[i++]); - } - } - left -= FWBUF_SIZE; - dp += FWBUF_SIZE; - } - if (left) { - if (config->user) { - if (copy_from_user(buf, dp, left)) - return -EFAULT; - } else { - memcpy(buf, dp, left); - } - for (i = 0; i < left; ) { - b1_put_byte(base, SEND_CONFIG); - for (j = 0; j < 4; j++) { - if (i < left) - b1_put_byte(base, buf[i++]); - else - b1_put_byte(base, 0); - } - } - } - return 0; -} - -int b1_loaded(avmcard *card) -{ - unsigned int base = card->port; - unsigned long stop; - unsigned char ans; - unsigned long tout = 2; - - for (stop = jiffies + tout * HZ; time_before(jiffies, stop);) { - if (b1_tx_empty(base)) - break; - } - if (!b1_tx_empty(base)) { - printk(KERN_ERR "%s: b1_loaded: tx err, corrupted t4 file ?\n", - card->name); - return 0; - } - b1_put_byte(base, SEND_POLL); - for (stop = jiffies + tout * HZ; time_before(jiffies, stop);) { - if (b1_rx_full(base)) { - ans = b1_get_byte(base); - if (ans == RECEIVE_POLL) - return 1; - - printk(KERN_ERR "%s: b1_loaded: got 0x%x, firmware not running\n", - card->name, ans); - return 0; - } - } - printk(KERN_ERR "%s: b1_loaded: firmware not running\n", card->name); - return 0; -} - -/* ------------------------------------------------------------- */ - -int b1_load_firmware(struct capi_ctr *ctrl, capiloaddata *data) -{ - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - avmcard *card = cinfo->card; - unsigned int port = card->port; - unsigned long flags; - int retval; - - b1_reset(port); - retval = b1_load_t4file(card, &data->firmware); - - if (retval) { - b1_reset(port); - printk(KERN_ERR "%s: failed to load t4file!!\n", - card->name); - return retval; - } - - b1_disable_irq(port); - - if (data->configuration.len > 0 && data->configuration.data) { - retval = b1_load_config(card, &data->configuration); - if (retval) { - b1_reset(port); - printk(KERN_ERR "%s: failed to load config!!\n", - card->name); - return retval; - } - } - - if (!b1_loaded(card)) { - printk(KERN_ERR "%s: failed to load t4file.\n", card->name); - return -EIO; - } - - spin_lock_irqsave(&card->lock, flags); - b1_setinterrupt(port, card->irq, card->cardtype); - b1_put_byte(port, SEND_INIT); - b1_put_word(port, CAPI_MAXAPPL); - b1_put_word(port, AVM_NCCI_PER_CHANNEL * 2); - b1_put_word(port, ctrl->cnr - 1); - spin_unlock_irqrestore(&card->lock, flags); - - return 0; -} - -void b1_reset_ctr(struct capi_ctr *ctrl) -{ - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - avmcard *card = cinfo->card; - unsigned int port = card->port; - unsigned long flags; - - b1_reset(port); - b1_reset(port); - - memset(cinfo->version, 0, sizeof(cinfo->version)); - spin_lock_irqsave(&card->lock, flags); - capilib_release(&cinfo->ncci_head); - spin_unlock_irqrestore(&card->lock, flags); - capi_ctr_down(ctrl); -} - -void b1_register_appl(struct capi_ctr *ctrl, - u16 appl, - capi_register_params *rp) -{ - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - avmcard *card = cinfo->card; - unsigned int port = card->port; - unsigned long flags; - int nconn, want = rp->level3cnt; - - if (want > 0) nconn = want; - else nconn = ctrl->profile.nbchannel * -want; - if (nconn == 0) nconn = ctrl->profile.nbchannel; - - spin_lock_irqsave(&card->lock, flags); - b1_put_byte(port, SEND_REGISTER); - b1_put_word(port, appl); - b1_put_word(port, 1024 * (nconn + 1)); - b1_put_word(port, nconn); - b1_put_word(port, rp->datablkcnt); - b1_put_word(port, rp->datablklen); - spin_unlock_irqrestore(&card->lock, flags); -} - -void b1_release_appl(struct capi_ctr *ctrl, u16 appl) -{ - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - avmcard *card = cinfo->card; - unsigned int port = card->port; - unsigned long flags; - - spin_lock_irqsave(&card->lock, flags); - capilib_release_appl(&cinfo->ncci_head, appl); - b1_put_byte(port, SEND_RELEASE); - b1_put_word(port, appl); - spin_unlock_irqrestore(&card->lock, flags); -} - -u16 b1_send_message(struct capi_ctr *ctrl, struct sk_buff *skb) -{ - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - avmcard *card = cinfo->card; - unsigned int port = card->port; - unsigned long flags; - u16 len = CAPIMSG_LEN(skb->data); - u8 cmd = CAPIMSG_COMMAND(skb->data); - u8 subcmd = CAPIMSG_SUBCOMMAND(skb->data); - u16 dlen, retval; - - spin_lock_irqsave(&card->lock, flags); - if (CAPICMD(cmd, subcmd) == CAPI_DATA_B3_REQ) { - retval = capilib_data_b3_req(&cinfo->ncci_head, - CAPIMSG_APPID(skb->data), - CAPIMSG_NCCI(skb->data), - CAPIMSG_MSGID(skb->data)); - if (retval != CAPI_NOERROR) { - spin_unlock_irqrestore(&card->lock, flags); - return retval; - } - - dlen = CAPIMSG_DATALEN(skb->data); - - b1_put_byte(port, SEND_DATA_B3_REQ); - b1_put_slice(port, skb->data, len); - b1_put_slice(port, skb->data + len, dlen); - } else { - b1_put_byte(port, SEND_MESSAGE); - b1_put_slice(port, skb->data, len); - } - spin_unlock_irqrestore(&card->lock, flags); - - dev_kfree_skb_any(skb); - return CAPI_NOERROR; -} - -/* ------------------------------------------------------------- */ - -void b1_parse_version(avmctrl_info *cinfo) -{ - struct capi_ctr *ctrl = &cinfo->capi_ctrl; - avmcard *card = cinfo->card; - capi_profile *profp; - u8 *dversion; - u8 flag; - int i, j; - - for (j = 0; j < AVM_MAXVERSION; j++) - cinfo->version[j] = ""; - for (i = 0, j = 0; - j < AVM_MAXVERSION && i < cinfo->versionlen; - j++, i += cinfo->versionbuf[i] + 1) - cinfo->version[j] = &cinfo->versionbuf[i + 1]; - - strlcpy(ctrl->serial, cinfo->version[VER_SERIAL], sizeof(ctrl->serial)); - memcpy(&ctrl->profile, cinfo->version[VER_PROFILE], sizeof(capi_profile)); - strlcpy(ctrl->manu, "AVM GmbH", sizeof(ctrl->manu)); - dversion = cinfo->version[VER_DRIVER]; - ctrl->version.majorversion = 2; - ctrl->version.minorversion = 0; - ctrl->version.majormanuversion = (((dversion[0] - '0') & 0xf) << 4); - ctrl->version.majormanuversion |= ((dversion[2] - '0') & 0xf); - ctrl->version.minormanuversion = (dversion[3] - '0') << 4; - ctrl->version.minormanuversion |= - (dversion[5] - '0') * 10 + ((dversion[6] - '0') & 0xf); - - profp = &ctrl->profile; - - flag = ((u8 *)(profp->manu))[1]; - switch (flag) { - case 0: if (cinfo->version[VER_CARDTYPE]) - strcpy(cinfo->cardname, cinfo->version[VER_CARDTYPE]); - else strcpy(cinfo->cardname, "B1"); - break; - case 3: strcpy(cinfo->cardname, "PCMCIA B"); break; - case 4: strcpy(cinfo->cardname, "PCMCIA M1"); break; - case 5: strcpy(cinfo->cardname, "PCMCIA M2"); break; - case 6: strcpy(cinfo->cardname, "B1 V3.0"); break; - case 7: strcpy(cinfo->cardname, "B1 PCI"); break; - default: sprintf(cinfo->cardname, "AVM?%u", (unsigned int)flag); break; - } - printk(KERN_NOTICE "%s: card %d \"%s\" ready.\n", - card->name, ctrl->cnr, cinfo->cardname); - - flag = ((u8 *)(profp->manu))[3]; - if (flag) - printk(KERN_NOTICE "%s: card %d Protocol:%s%s%s%s%s%s%s\n", - card->name, - ctrl->cnr, - (flag & 0x01) ? " DSS1" : "", - (flag & 0x02) ? " CT1" : "", - (flag & 0x04) ? " VN3" : "", - (flag & 0x08) ? " NI1" : "", - (flag & 0x10) ? " AUSTEL" : "", - (flag & 0x20) ? " ESS" : "", - (flag & 0x40) ? " 1TR6" : "" - ); - - flag = ((u8 *)(profp->manu))[5]; - if (flag) - printk(KERN_NOTICE "%s: card %d Linetype:%s%s%s%s\n", - card->name, - ctrl->cnr, - (flag & 0x01) ? " point to point" : "", - (flag & 0x02) ? " point to multipoint" : "", - (flag & 0x08) ? " leased line without D-channel" : "", - (flag & 0x04) ? " leased line with D-channel" : "" - ); -} - -/* ------------------------------------------------------------- */ - -irqreturn_t b1_interrupt(int interrupt, void *devptr) -{ - avmcard *card = devptr; - avmctrl_info *cinfo = &card->ctrlinfo[0]; - struct capi_ctr *ctrl = &cinfo->capi_ctrl; - unsigned char b1cmd; - struct sk_buff *skb; - - unsigned ApplId; - unsigned MsgLen; - unsigned DataB3Len; - unsigned NCCI; - unsigned WindowSize; - unsigned long flags; - - spin_lock_irqsave(&card->lock, flags); - - if (!b1_rx_full(card->port)) { - spin_unlock_irqrestore(&card->lock, flags); - return IRQ_NONE; - } - - b1cmd = b1_get_byte(card->port); - - switch (b1cmd) { - - case RECEIVE_DATA_B3_IND: - - ApplId = (unsigned) b1_get_word(card->port); - MsgLen = b1_get_slice(card->port, card->msgbuf); - DataB3Len = b1_get_slice(card->port, card->databuf); - spin_unlock_irqrestore(&card->lock, flags); - - if (MsgLen < 30) { /* not CAPI 64Bit */ - memset(card->msgbuf + MsgLen, 0, 30-MsgLen); - MsgLen = 30; - CAPIMSG_SETLEN(card->msgbuf, 30); - } - - skb = alloc_skb(DataB3Len + MsgLen, GFP_ATOMIC); - if (!skb) { - printk(KERN_ERR "%s: incoming packet dropped\n", - card->name); - } else { - skb_put_data(skb, card->msgbuf, MsgLen); - skb_put_data(skb, card->databuf, DataB3Len); - capi_ctr_handle_message(ctrl, ApplId, skb); - } - break; - - case RECEIVE_MESSAGE: - - ApplId = (unsigned) b1_get_word(card->port); - MsgLen = b1_get_slice(card->port, card->msgbuf); - skb = alloc_skb(MsgLen, GFP_ATOMIC); - - if (!skb) { - printk(KERN_ERR "%s: incoming packet dropped\n", - card->name); - spin_unlock_irqrestore(&card->lock, flags); - } else { - skb_put_data(skb, card->msgbuf, MsgLen); - if (CAPIMSG_CMD(skb->data) == CAPI_DATA_B3_CONF) - capilib_data_b3_conf(&cinfo->ncci_head, ApplId, - CAPIMSG_NCCI(skb->data), - CAPIMSG_MSGID(skb->data)); - spin_unlock_irqrestore(&card->lock, flags); - capi_ctr_handle_message(ctrl, ApplId, skb); - } - break; - - case RECEIVE_NEW_NCCI: - - ApplId = b1_get_word(card->port); - NCCI = b1_get_word(card->port); - WindowSize = b1_get_word(card->port); - capilib_new_ncci(&cinfo->ncci_head, ApplId, NCCI, WindowSize); - spin_unlock_irqrestore(&card->lock, flags); - break; - - case RECEIVE_FREE_NCCI: - - ApplId = b1_get_word(card->port); - NCCI = b1_get_word(card->port); - if (NCCI != 0xffffffff) - capilib_free_ncci(&cinfo->ncci_head, ApplId, NCCI); - spin_unlock_irqrestore(&card->lock, flags); - break; - - case RECEIVE_START: - /* b1_put_byte(card->port, SEND_POLLACK); */ - spin_unlock_irqrestore(&card->lock, flags); - capi_ctr_resume_output(ctrl); - break; - - case RECEIVE_STOP: - spin_unlock_irqrestore(&card->lock, flags); - capi_ctr_suspend_output(ctrl); - break; - - case RECEIVE_INIT: - - cinfo->versionlen = b1_get_slice(card->port, cinfo->versionbuf); - spin_unlock_irqrestore(&card->lock, flags); - b1_parse_version(cinfo); - printk(KERN_INFO "%s: %s-card (%s) now active\n", - card->name, - cinfo->version[VER_CARDTYPE], - cinfo->version[VER_DRIVER]); - capi_ctr_ready(ctrl); - break; - - case RECEIVE_TASK_READY: - ApplId = (unsigned) b1_get_word(card->port); - MsgLen = b1_get_slice(card->port, card->msgbuf); - spin_unlock_irqrestore(&card->lock, flags); - card->msgbuf[MsgLen] = 0; - while (MsgLen > 0 - && (card->msgbuf[MsgLen - 1] == '\n' - || card->msgbuf[MsgLen - 1] == '\r')) { - card->msgbuf[MsgLen - 1] = 0; - MsgLen--; - } - printk(KERN_INFO "%s: task %d \"%s\" ready.\n", - card->name, ApplId, card->msgbuf); - break; - - case RECEIVE_DEBUGMSG: - MsgLen = b1_get_slice(card->port, card->msgbuf); - spin_unlock_irqrestore(&card->lock, flags); - card->msgbuf[MsgLen] = 0; - while (MsgLen > 0 - && (card->msgbuf[MsgLen - 1] == '\n' - || card->msgbuf[MsgLen - 1] == '\r')) { - card->msgbuf[MsgLen - 1] = 0; - MsgLen--; - } - printk(KERN_INFO "%s: DEBUG: %s\n", card->name, card->msgbuf); - break; - - case 0xff: - spin_unlock_irqrestore(&card->lock, flags); - printk(KERN_ERR "%s: card removed ?\n", card->name); - return IRQ_NONE; - default: - spin_unlock_irqrestore(&card->lock, flags); - printk(KERN_ERR "%s: b1_interrupt: 0x%x ???\n", - card->name, b1cmd); - return IRQ_HANDLED; - } - return IRQ_HANDLED; -} - -/* ------------------------------------------------------------- */ -int b1_proc_show(struct seq_file *m, void *v) -{ - struct capi_ctr *ctrl = m->private; - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - avmcard *card = cinfo->card; - u8 flag; - char *s; - - seq_printf(m, "%-16s %s\n", "name", card->name); - seq_printf(m, "%-16s 0x%x\n", "io", card->port); - seq_printf(m, "%-16s %d\n", "irq", card->irq); - switch (card->cardtype) { - case avm_b1isa: s = "B1 ISA"; break; - case avm_b1pci: s = "B1 PCI"; break; - case avm_b1pcmcia: s = "B1 PCMCIA"; break; - case avm_m1: s = "M1"; break; - case avm_m2: s = "M2"; break; - case avm_t1isa: s = "T1 ISA (HEMA)"; break; - case avm_t1pci: s = "T1 PCI"; break; - case avm_c4: s = "C4"; break; - case avm_c2: s = "C2"; break; - default: s = "???"; break; - } - seq_printf(m, "%-16s %s\n", "type", s); - if (card->cardtype == avm_t1isa) - seq_printf(m, "%-16s %d\n", "cardnr", card->cardnr); - - s = cinfo->version[VER_DRIVER]; - if (s) - seq_printf(m, "%-16s %s\n", "ver_driver", s); - - s = cinfo->version[VER_CARDTYPE]; - if (s) - seq_printf(m, "%-16s %s\n", "ver_cardtype", s); - - s = cinfo->version[VER_SERIAL]; - if (s) - seq_printf(m, "%-16s %s\n", "ver_serial", s); - - if (card->cardtype != avm_m1) { - flag = ((u8 *)(ctrl->profile.manu))[3]; - if (flag) - seq_printf(m, "%-16s%s%s%s%s%s%s%s\n", - "protocol", - (flag & 0x01) ? " DSS1" : "", - (flag & 0x02) ? " CT1" : "", - (flag & 0x04) ? " VN3" : "", - (flag & 0x08) ? " NI1" : "", - (flag & 0x10) ? " AUSTEL" : "", - (flag & 0x20) ? " ESS" : "", - (flag & 0x40) ? " 1TR6" : "" - ); - } - if (card->cardtype != avm_m1) { - flag = ((u8 *)(ctrl->profile.manu))[5]; - if (flag) - seq_printf(m, "%-16s%s%s%s%s\n", - "linetype", - (flag & 0x01) ? " point to point" : "", - (flag & 0x02) ? " point to multipoint" : "", - (flag & 0x08) ? " leased line without D-channel" : "", - (flag & 0x04) ? " leased line with D-channel" : "" - ); - } - seq_printf(m, "%-16s %s\n", "cardname", cinfo->cardname); - - return 0; -} -EXPORT_SYMBOL(b1_proc_show); - -/* ------------------------------------------------------------- */ - -#ifdef CONFIG_PCI - -avmcard_dmainfo * -avmcard_dma_alloc(char *name, struct pci_dev *pdev, long rsize, long ssize) -{ - avmcard_dmainfo *p; - void *buf; - - p = kzalloc(sizeof(avmcard_dmainfo), GFP_KERNEL); - if (!p) { - printk(KERN_WARNING "%s: no memory.\n", name); - goto err; - } - - p->recvbuf.size = rsize; - buf = pci_alloc_consistent(pdev, rsize, &p->recvbuf.dmaaddr); - if (!buf) { - printk(KERN_WARNING "%s: allocation of receive dma buffer failed.\n", name); - goto err_kfree; - } - p->recvbuf.dmabuf = buf; - - p->sendbuf.size = ssize; - buf = pci_alloc_consistent(pdev, ssize, &p->sendbuf.dmaaddr); - if (!buf) { - printk(KERN_WARNING "%s: allocation of send dma buffer failed.\n", name); - goto err_free_consistent; - } - - p->sendbuf.dmabuf = buf; - skb_queue_head_init(&p->send_queue); - - return p; - -err_free_consistent: - pci_free_consistent(p->pcidev, p->recvbuf.size, - p->recvbuf.dmabuf, p->recvbuf.dmaaddr); -err_kfree: - kfree(p); -err: - return NULL; -} - -void avmcard_dma_free(avmcard_dmainfo *p) -{ - pci_free_consistent(p->pcidev, p->recvbuf.size, - p->recvbuf.dmabuf, p->recvbuf.dmaaddr); - pci_free_consistent(p->pcidev, p->sendbuf.size, - p->sendbuf.dmabuf, p->sendbuf.dmaaddr); - skb_queue_purge(&p->send_queue); - kfree(p); -} - -EXPORT_SYMBOL(avmcard_dma_alloc); -EXPORT_SYMBOL(avmcard_dma_free); - -#endif - -EXPORT_SYMBOL(b1_irq_table); - -EXPORT_SYMBOL(b1_alloc_card); -EXPORT_SYMBOL(b1_free_card); -EXPORT_SYMBOL(b1_detect); -EXPORT_SYMBOL(b1_getrevision); -EXPORT_SYMBOL(b1_load_t4file); -EXPORT_SYMBOL(b1_load_config); -EXPORT_SYMBOL(b1_loaded); -EXPORT_SYMBOL(b1_load_firmware); -EXPORT_SYMBOL(b1_reset_ctr); -EXPORT_SYMBOL(b1_register_appl); -EXPORT_SYMBOL(b1_release_appl); -EXPORT_SYMBOL(b1_send_message); - -EXPORT_SYMBOL(b1_parse_version); -EXPORT_SYMBOL(b1_interrupt); - -static int __init b1_init(void) -{ - char *p; - char rev[32]; - - p = strchr(revision, ':'); - if (p && p[1]) { - strlcpy(rev, p + 2, 32); - p = strchr(rev, '$'); - if (p && p > rev) - *(p - 1) = 0; - } else { - strcpy(rev, "1.0"); - } - printk(KERN_INFO "b1: revision %s\n", rev); - - return 0; -} - -static void __exit b1_exit(void) -{ -} - -module_init(b1_init); -module_exit(b1_exit); diff --git a/drivers/staging/isdn/avm/b1dma.c b/drivers/staging/isdn/avm/b1dma.c deleted file mode 100644 index 6a3dc9937ce5..000000000000 --- a/drivers/staging/isdn/avm/b1dma.c +++ /dev/null @@ -1,981 +0,0 @@ -/* $Id: b1dma.c,v 1.1.2.3 2004/02/10 01:07:12 keil Exp $ - * - * Common module for AVM B1 cards that support dma with AMCC - * - * Copyright 2000 by Carsten Paeth <calle@calle.de> - * - * This software may be used and distributed according to the terms - * of the GNU General Public License, incorporated herein by reference. - * - */ - -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/proc_fs.h> -#include <linux/seq_file.h> -#include <linux/skbuff.h> -#include <linux/delay.h> -#include <linux/mm.h> -#include <linux/interrupt.h> -#include <linux/ioport.h> -#include <linux/capi.h> -#include <linux/kernelcapi.h> -#include <linux/gfp.h> -#include <asm/io.h> -#include <linux/init.h> -#include <linux/uaccess.h> -#include <linux/netdevice.h> -#include <linux/isdn/capilli.h> -#include "avmcard.h" -#include <linux/isdn/capicmd.h> -#include <linux/isdn/capiutil.h> - -static char *revision = "$Revision: 1.1.2.3 $"; - -#undef AVM_B1DMA_DEBUG - -/* ------------------------------------------------------------- */ - -MODULE_DESCRIPTION("CAPI4Linux: DMA support for active AVM cards"); -MODULE_AUTHOR("Carsten Paeth"); -MODULE_LICENSE("GPL"); - -static bool suppress_pollack = 0; -module_param(suppress_pollack, bool, 0); - -/* ------------------------------------------------------------- */ - -static void b1dma_dispatch_tx(avmcard *card); - -/* ------------------------------------------------------------- */ - -/* S5933 */ - -#define AMCC_RXPTR 0x24 -#define AMCC_RXLEN 0x28 -#define AMCC_TXPTR 0x2c -#define AMCC_TXLEN 0x30 - -#define AMCC_INTCSR 0x38 -# define EN_READ_TC_INT 0x00008000L -# define EN_WRITE_TC_INT 0x00004000L -# define EN_TX_TC_INT EN_READ_TC_INT -# define EN_RX_TC_INT EN_WRITE_TC_INT -# define AVM_FLAG 0x30000000L - -# define ANY_S5933_INT 0x00800000L -# define READ_TC_INT 0x00080000L -# define WRITE_TC_INT 0x00040000L -# define TX_TC_INT READ_TC_INT -# define RX_TC_INT WRITE_TC_INT -# define MASTER_ABORT_INT 0x00100000L -# define TARGET_ABORT_INT 0x00200000L -# define BUS_MASTER_INT 0x00200000L -# define ALL_INT 0x000C0000L - -#define AMCC_MCSR 0x3c -# define A2P_HI_PRIORITY 0x00000100L -# define EN_A2P_TRANSFERS 0x00000400L -# define P2A_HI_PRIORITY 0x00001000L -# define EN_P2A_TRANSFERS 0x00004000L -# define RESET_A2P_FLAGS 0x04000000L -# define RESET_P2A_FLAGS 0x02000000L - -/* ------------------------------------------------------------- */ - -static inline void b1dma_writel(avmcard *card, u32 value, int off) -{ - writel(value, card->mbase + off); -} - -static inline u32 b1dma_readl(avmcard *card, int off) -{ - return readl(card->mbase + off); -} - -/* ------------------------------------------------------------- */ - -static inline int b1dma_tx_empty(unsigned int port) -{ - return inb(port + 0x03) & 0x1; -} - -static inline int b1dma_rx_full(unsigned int port) -{ - return inb(port + 0x02) & 0x1; -} - -static int b1dma_tolink(avmcard *card, void *buf, unsigned int len) -{ - unsigned long stop = jiffies + 1 * HZ; /* maximum wait time 1 sec */ - unsigned char *s = (unsigned char *)buf; - while (len--) { - while (!b1dma_tx_empty(card->port) - && time_before(jiffies, stop)); - if (!b1dma_tx_empty(card->port)) - return -1; - t1outp(card->port, 0x01, *s++); - } - return 0; -} - -static int b1dma_fromlink(avmcard *card, void *buf, unsigned int len) -{ - unsigned long stop = jiffies + 1 * HZ; /* maximum wait time 1 sec */ - unsigned char *s = (unsigned char *)buf; - while (len--) { - while (!b1dma_rx_full(card->port) - && time_before(jiffies, stop)); - if (!b1dma_rx_full(card->port)) - return -1; - *s++ = t1inp(card->port, 0x00); - } - return 0; -} - -static int WriteReg(avmcard *card, u32 reg, u8 val) -{ - u8 cmd = 0x00; - if (b1dma_tolink(card, &cmd, 1) == 0 - && b1dma_tolink(card, ®, 4) == 0) { - u32 tmp = val; - return b1dma_tolink(card, &tmp, 4); - } - return -1; -} - -static u8 ReadReg(avmcard *card, u32 reg) -{ - u8 cmd = 0x01; - if (b1dma_tolink(card, &cmd, 1) == 0 - && b1dma_tolink(card, ®, 4) == 0) { - u32 tmp; - if (b1dma_fromlink(card, &tmp, 4) == 0) - return (u8)tmp; - } - return 0xff; -} - -/* ------------------------------------------------------------- */ - -static inline void _put_byte(void **pp, u8 val) -{ - u8 *s = *pp; - *s++ = val; - *pp = s; -} - -static inline void _put_word(void **pp, u32 val) -{ - u8 *s = *pp; - *s++ = val & 0xff; - *s++ = (val >> 8) & 0xff; - *s++ = (val >> 16) & 0xff; - *s++ = (val >> 24) & 0xff; - *pp = s; -} - -static inline void _put_slice(void **pp, unsigned char *dp, unsigned int len) -{ - unsigned i = len; - _put_word(pp, i); - while (i-- > 0) - _put_byte(pp, *dp++); -} - -static inline u8 _get_byte(void **pp) -{ - u8 *s = *pp; - u8 val; - val = *s++; - *pp = s; - return val; -} - -static inline u32 _get_word(void **pp) -{ - u8 *s = *pp; - u32 val; - val = *s++; - val |= (*s++ << 8); - val |= (*s++ << 16); - val |= (*s++ << 24); - *pp = s; - return val; -} - -static inline u32 _get_slice(void **pp, unsigned char *dp) -{ - unsigned int len, i; - - len = i = _get_word(pp); - while (i-- > 0) *dp++ = _get_byte(pp); - return len; -} - -/* ------------------------------------------------------------- */ - -void b1dma_reset(avmcard *card) -{ - card->csr = 0x0; - b1dma_writel(card, card->csr, AMCC_INTCSR); - b1dma_writel(card, 0, AMCC_MCSR); - b1dma_writel(card, 0, AMCC_RXLEN); - b1dma_writel(card, 0, AMCC_TXLEN); - - t1outp(card->port, 0x10, 0x00); - t1outp(card->port, 0x07, 0x00); - - b1dma_writel(card, 0, AMCC_MCSR); - mdelay(10); - b1dma_writel(card, 0x0f000000, AMCC_MCSR); /* reset all */ - mdelay(10); - b1dma_writel(card, 0, AMCC_MCSR); - if (card->cardtype == avm_t1pci) - mdelay(42); - else - mdelay(10); -} - -/* ------------------------------------------------------------- */ - -static int b1dma_detect(avmcard *card) -{ - b1dma_writel(card, 0, AMCC_MCSR); - mdelay(10); - b1dma_writel(card, 0x0f000000, AMCC_MCSR); /* reset all */ - mdelay(10); - b1dma_writel(card, 0, AMCC_MCSR); - mdelay(42); - - b1dma_writel(card, 0, AMCC_RXLEN); - b1dma_writel(card, 0, AMCC_TXLEN); - card->csr = 0x0; - b1dma_writel(card, card->csr, AMCC_INTCSR); - - if (b1dma_readl(card, AMCC_MCSR) != 0x000000E6) - return 1; - - b1dma_writel(card, 0xffffffff, AMCC_RXPTR); - b1dma_writel(card, 0xffffffff, AMCC_TXPTR); - if (b1dma_readl(card, AMCC_RXPTR) != 0xfffffffc - || b1dma_readl(card, AMCC_TXPTR) != 0xfffffffc) - return 2; - - b1dma_writel(card, 0x0, AMCC_RXPTR); - b1dma_writel(card, 0x0, AMCC_TXPTR); - if (b1dma_readl(card, AMCC_RXPTR) != 0x0 - || b1dma_readl(card, AMCC_TXPTR) != 0x0) - return 3; - - t1outp(card->port, 0x10, 0x00); - t1outp(card->port, 0x07, 0x00); - - t1outp(card->port, 0x02, 0x02); - t1outp(card->port, 0x03, 0x02); - - if ((t1inp(card->port, 0x02) & 0xFE) != 0x02 - || t1inp(card->port, 0x3) != 0x03) - return 4; - - t1outp(card->port, 0x02, 0x00); - t1outp(card->port, 0x03, 0x00); - - if ((t1inp(card->port, 0x02) & 0xFE) != 0x00 - || t1inp(card->port, 0x3) != 0x01) - return 5; - - return 0; -} - -int t1pci_detect(avmcard *card) -{ - int ret; - - if ((ret = b1dma_detect(card)) != 0) - return ret; - - /* Transputer test */ - - if (WriteReg(card, 0x80001000, 0x11) != 0 - || WriteReg(card, 0x80101000, 0x22) != 0 - || WriteReg(card, 0x80201000, 0x33) != 0 - || WriteReg(card, 0x80301000, 0x44) != 0) - return 6; - - if (ReadReg(card, 0x80001000) != 0x11 - || ReadReg(card, 0x80101000) != 0x22 - || ReadReg(card, 0x80201000) != 0x33 - || ReadReg(card, 0x80301000) != 0x44) - return 7; - - if (WriteReg(card, 0x80001000, 0x55) != 0 - || WriteReg(card, 0x80101000, 0x66) != 0 - || WriteReg(card, 0x80201000, 0x77) != 0 - || WriteReg(card, 0x80301000, 0x88) != 0) - return 8; - - if (ReadReg(card, 0x80001000) != 0x55 - || ReadReg(card, 0x80101000) != 0x66 - || ReadReg(card, 0x80201000) != 0x77 - || ReadReg(card, 0x80301000) != 0x88) - return 9; - - return 0; -} - -int b1pciv4_detect(avmcard *card) -{ - int ret, i; - - if ((ret = b1dma_detect(card)) != 0) - return ret; - - for (i = 0; i < 5; i++) { - if (WriteReg(card, 0x80A00000, 0x21) != 0) - return 6; - if ((ReadReg(card, 0x80A00000) & 0x01) != 0x01) - return 7; - } - for (i = 0; i < 5; i++) { - if (WriteReg(card, 0x80A00000, 0x20) != 0) - return 8; - if ((ReadReg(card, 0x80A00000) & 0x01) != 0x00) - return 9; - } - - return 0; -} - -static void b1dma_queue_tx(avmcard *card, struct sk_buff *skb) -{ - unsigned long flags; - - spin_lock_irqsave(&card->lock, flags); - - skb_queue_tail(&card->dma->send_queue, skb); - - if (!(card->csr & EN_TX_TC_INT)) { - b1dma_dispatch_tx(card); - b1dma_writel(card, card->csr, AMCC_INTCSR); - } - - spin_unlock_irqrestore(&card->lock, flags); -} - -/* ------------------------------------------------------------- */ - -static void b1dma_dispatch_tx(avmcard *card) -{ - avmcard_dmainfo *dma = card->dma; - struct sk_buff *skb; - u8 cmd, subcmd; - u16 len; - u32 txlen; - void *p; - - skb = skb_dequeue(&dma->send_queue); - - len = CAPIMSG_LEN(skb->data); - - if (len) { - cmd = CAPIMSG_COMMAND(skb->data); - subcmd = CAPIMSG_SUBCOMMAND(skb->data); - - p = dma->sendbuf.dmabuf; - - if (CAPICMD(cmd, subcmd) == CAPI_DATA_B3_REQ) { - u16 dlen = CAPIMSG_DATALEN(skb->data); - _put_byte(&p, SEND_DATA_B3_REQ); - _put_slice(&p, skb->data, len); - _put_slice(&p, skb->data + len, dlen); - } else { - _put_byte(&p, SEND_MESSAGE); - _put_slice(&p, skb->data, len); - } - txlen = (u8 *)p - (u8 *)dma->sendbuf.dmabuf; -#ifdef AVM_B1DMA_DEBUG - printk(KERN_DEBUG "tx: put msg len=%d\n", txlen); -#endif - } else { - txlen = skb->len - 2; -#ifdef AVM_B1DMA_POLLDEBUG - if (skb->data[2] == SEND_POLLACK) - printk(KERN_INFO "%s: send ack\n", card->name); -#endif -#ifdef AVM_B1DMA_DEBUG - printk(KERN_DEBUG "tx: put 0x%x len=%d\n", - skb->data[2], txlen); -#endif - skb_copy_from_linear_data_offset(skb, 2, dma->sendbuf.dmabuf, - skb->len - 2); - } - txlen = (txlen + 3) & ~3; - - b1dma_writel(card, dma->sendbuf.dmaaddr, AMCC_TXPTR); - b1dma_writel(card, txlen, AMCC_TXLEN); - - card->csr |= EN_TX_TC_INT; - - dev_kfree_skb_any(skb); -} - -/* ------------------------------------------------------------- */ - -static void queue_pollack(avmcard *card) -{ - struct sk_buff *skb; - void *p; - - skb = alloc_skb(3, GFP_ATOMIC); - if (!skb) { - printk(KERN_CRIT "%s: no memory, lost poll ack\n", - card->name); - return; - } - p = skb->data; - _put_byte(&p, 0); - _put_byte(&p, 0); - _put_byte(&p, SEND_POLLACK); - skb_put(skb, (u8 *)p - (u8 *)skb->data); - - b1dma_queue_tx(card, skb); -} - -/* ------------------------------------------------------------- */ - -static void b1dma_handle_rx(avmcard *card) -{ - avmctrl_info *cinfo = &card->ctrlinfo[0]; - avmcard_dmainfo *dma = card->dma; - struct capi_ctr *ctrl = &cinfo->capi_ctrl; - struct sk_buff *skb; - void *p = dma->recvbuf.dmabuf + 4; - u32 ApplId, MsgLen, DataB3Len, NCCI, WindowSize; - u8 b1cmd = _get_byte(&p); - -#ifdef AVM_B1DMA_DEBUG - printk(KERN_DEBUG "rx: 0x%x %lu\n", b1cmd, (unsigned long)dma->recvlen); -#endif - - switch (b1cmd) { - case RECEIVE_DATA_B3_IND: - - ApplId = (unsigned) _get_word(&p); - MsgLen = _get_slice(&p, card->msgbuf); - DataB3Len = _get_slice(&p, card->databuf); - - if (MsgLen < 30) { /* not CAPI 64Bit */ - memset(card->msgbuf + MsgLen, 0, 30 - MsgLen); - MsgLen = 30; - CAPIMSG_SETLEN(card->msgbuf, 30); - } - if (!(skb = alloc_skb(DataB3Len + MsgLen, GFP_ATOMIC))) { - printk(KERN_ERR "%s: incoming packet dropped\n", - card->name); - } else { - skb_put_data(skb, card->msgbuf, MsgLen); - skb_put_data(skb, card->databuf, DataB3Len); - capi_ctr_handle_message(ctrl, ApplId, skb); - } - break; - - case RECEIVE_MESSAGE: - - ApplId = (unsigned) _get_word(&p); - MsgLen = _get_slice(&p, card->msgbuf); - if (!(skb = alloc_skb(MsgLen, GFP_ATOMIC))) { - printk(KERN_ERR "%s: incoming packet dropped\n", - card->name); - } else { - skb_put_data(skb, card->msgbuf, MsgLen); - if (CAPIMSG_CMD(skb->data) == CAPI_DATA_B3_CONF) { - spin_lock(&card->lock); - capilib_data_b3_conf(&cinfo->ncci_head, ApplId, - CAPIMSG_NCCI(skb->data), - CAPIMSG_MSGID(skb->data)); - spin_unlock(&card->lock); - } - capi_ctr_handle_message(ctrl, ApplId, skb); - } - break; - - case RECEIVE_NEW_NCCI: - - ApplId = _get_word(&p); - NCCI = _get_word(&p); - WindowSize = _get_word(&p); - spin_lock(&card->lock); - capilib_new_ncci(&cinfo->ncci_head, ApplId, NCCI, WindowSize); - spin_unlock(&card->lock); - break; - - case RECEIVE_FREE_NCCI: - - ApplId = _get_word(&p); - NCCI = _get_word(&p); - - if (NCCI != 0xffffffff) { - spin_lock(&card->lock); - capilib_free_ncci(&cinfo->ncci_head, ApplId, NCCI); - spin_unlock(&card->lock); - } - break; - - case RECEIVE_START: -#ifdef AVM_B1DMA_POLLDEBUG - printk(KERN_INFO "%s: receive poll\n", card->name); -#endif - if (!suppress_pollack) - queue_pollack(card); - capi_ctr_resume_output(ctrl); - break; - - case RECEIVE_STOP: - capi_ctr_suspend_output(ctrl); - break; - - case RECEIVE_INIT: - - cinfo->versionlen = _get_slice(&p, cinfo->versionbuf); - b1_parse_version(cinfo); - printk(KERN_INFO "%s: %s-card (%s) now active\n", - card->name, - cinfo->version[VER_CARDTYPE], - cinfo->version[VER_DRIVER]); - capi_ctr_ready(ctrl); - break; - - case RECEIVE_TASK_READY: - ApplId = (unsigned) _get_word(&p); - MsgLen = _get_slice(&p, card->msgbuf); - card->msgbuf[MsgLen] = 0; - while (MsgLen > 0 - && (card->msgbuf[MsgLen - 1] == '\n' - || card->msgbuf[MsgLen - 1] == '\r')) { - card->msgbuf[MsgLen - 1] = 0; - MsgLen--; - } - printk(KERN_INFO "%s: task %d \"%s\" ready.\n", - card->name, ApplId, card->msgbuf); - break; - - case RECEIVE_DEBUGMSG: - MsgLen = _get_slice(&p, card->msgbuf); - card->msgbuf[MsgLen] = 0; - while (MsgLen > 0 - && (card->msgbuf[MsgLen - 1] == '\n' - || card->msgbuf[MsgLen - 1] == '\r')) { - card->msgbuf[MsgLen - 1] = 0; - MsgLen--; - } - printk(KERN_INFO "%s: DEBUG: %s\n", card->name, card->msgbuf); - break; - - default: - printk(KERN_ERR "%s: b1dma_interrupt: 0x%x ???\n", - card->name, b1cmd); - return; - } -} - -/* ------------------------------------------------------------- */ - -static void b1dma_handle_interrupt(avmcard *card) -{ - u32 status; - u32 newcsr; - - spin_lock(&card->lock); - - status = b1dma_readl(card, AMCC_INTCSR); - if ((status & ANY_S5933_INT) == 0) { - spin_unlock(&card->lock); - return; - } - - newcsr = card->csr | (status & ALL_INT); - if (status & TX_TC_INT) newcsr &= ~EN_TX_TC_INT; - if (status & RX_TC_INT) newcsr &= ~EN_RX_TC_INT; - b1dma_writel(card, newcsr, AMCC_INTCSR); - - if ((status & RX_TC_INT) != 0) { - struct avmcard_dmainfo *dma = card->dma; - u32 rxlen; - if (card->dma->recvlen == 0) { - rxlen = b1dma_readl(card, AMCC_RXLEN); - if (rxlen == 0) { - dma->recvlen = *((u32 *)dma->recvbuf.dmabuf); - rxlen = (dma->recvlen + 3) & ~3; - b1dma_writel(card, dma->recvbuf.dmaaddr + 4, AMCC_RXPTR); - b1dma_writel(card, rxlen, AMCC_RXLEN); -#ifdef AVM_B1DMA_DEBUG - } else { - printk(KERN_ERR "%s: rx not complete (%d).\n", - card->name, rxlen); -#endif - } - } else { - spin_unlock(&card->lock); - b1dma_handle_rx(card); - dma->recvlen = 0; - spin_lock(&card->lock); - b1dma_writel(card, dma->recvbuf.dmaaddr, AMCC_RXPTR); - b1dma_writel(card, 4, AMCC_RXLEN); - } - } - - if ((status & TX_TC_INT) != 0) { - if (skb_queue_empty(&card->dma->send_queue)) - card->csr &= ~EN_TX_TC_INT; - else - b1dma_dispatch_tx(card); - } - b1dma_writel(card, card->csr, AMCC_INTCSR); - - spin_unlock(&card->lock); -} - -irqreturn_t b1dma_interrupt(int interrupt, void *devptr) -{ - avmcard *card = devptr; - - b1dma_handle_interrupt(card); - return IRQ_HANDLED; -} - -/* ------------------------------------------------------------- */ - -static int b1dma_loaded(avmcard *card) -{ - unsigned long stop; - unsigned char ans; - unsigned long tout = 2; - unsigned int base = card->port; - - for (stop = jiffies + tout * HZ; time_before(jiffies, stop);) { - if (b1_tx_empty(base)) - break; - } - if (!b1_tx_empty(base)) { - printk(KERN_ERR "%s: b1dma_loaded: tx err, corrupted t4 file ?\n", - card->name); - return 0; - } - b1_put_byte(base, SEND_POLLACK); - for (stop = jiffies + tout * HZ; time_before(jiffies, stop);) { - if (b1_rx_full(base)) { - if ((ans = b1_get_byte(base)) == RECEIVE_POLLDWORD) { - return 1; - } - printk(KERN_ERR "%s: b1dma_loaded: got 0x%x, firmware not running in dword mode\n", card->name, ans); - return 0; - } - } - printk(KERN_ERR "%s: b1dma_loaded: firmware not running\n", card->name); - return 0; -} - -/* ------------------------------------------------------------- */ - -static void b1dma_send_init(avmcard *card) -{ - struct sk_buff *skb; - void *p; - - skb = alloc_skb(15, GFP_ATOMIC); - if (!skb) { - printk(KERN_CRIT "%s: no memory, lost register appl.\n", - card->name); - return; - } - p = skb->data; - _put_byte(&p, 0); - _put_byte(&p, 0); - _put_byte(&p, SEND_INIT); - _put_word(&p, CAPI_MAXAPPL); - _put_word(&p, AVM_NCCI_PER_CHANNEL * 30); - _put_word(&p, card->cardnr - 1); - skb_put(skb, (u8 *)p - (u8 *)skb->data); - - b1dma_queue_tx(card, skb); -} - -int b1dma_load_firmware(struct capi_ctr *ctrl, capiloaddata *data) -{ - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - avmcard *card = cinfo->card; - int retval; - - b1dma_reset(card); - - if ((retval = b1_load_t4file(card, &data->firmware))) { - b1dma_reset(card); - printk(KERN_ERR "%s: failed to load t4file!!\n", - card->name); - return retval; - } - - if (data->configuration.len > 0 && data->configuration.data) { - if ((retval = b1_load_config(card, &data->configuration))) { - b1dma_reset(card); - printk(KERN_ERR "%s: failed to load config!!\n", - card->name); - return retval; - } - } - - if (!b1dma_loaded(card)) { - b1dma_reset(card); - printk(KERN_ERR "%s: failed to load t4file.\n", card->name); - return -EIO; - } - - card->csr = AVM_FLAG; - b1dma_writel(card, card->csr, AMCC_INTCSR); - b1dma_writel(card, EN_A2P_TRANSFERS | EN_P2A_TRANSFERS | A2P_HI_PRIORITY | - P2A_HI_PRIORITY | RESET_A2P_FLAGS | RESET_P2A_FLAGS, - AMCC_MCSR); - t1outp(card->port, 0x07, 0x30); - t1outp(card->port, 0x10, 0xF0); - - card->dma->recvlen = 0; - b1dma_writel(card, card->dma->recvbuf.dmaaddr, AMCC_RXPTR); - b1dma_writel(card, 4, AMCC_RXLEN); - card->csr |= EN_RX_TC_INT; - b1dma_writel(card, card->csr, AMCC_INTCSR); - - b1dma_send_init(card); - - return 0; -} - -void b1dma_reset_ctr(struct capi_ctr *ctrl) -{ - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - avmcard *card = cinfo->card; - unsigned long flags; - - spin_lock_irqsave(&card->lock, flags); - b1dma_reset(card); - - memset(cinfo->version, 0, sizeof(cinfo->version)); - capilib_release(&cinfo->ncci_head); - spin_unlock_irqrestore(&card->lock, flags); - capi_ctr_down(ctrl); -} - -/* ------------------------------------------------------------- */ - -void b1dma_register_appl(struct capi_ctr *ctrl, - u16 appl, - capi_register_params *rp) -{ - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - avmcard *card = cinfo->card; - struct sk_buff *skb; - int want = rp->level3cnt; - int nconn; - void *p; - - if (want > 0) nconn = want; - else nconn = ctrl->profile.nbchannel * -want; - if (nconn == 0) nconn = ctrl->profile.nbchannel; - - skb = alloc_skb(23, GFP_ATOMIC); - if (!skb) { - printk(KERN_CRIT "%s: no memory, lost register appl.\n", - card->name); - return; - } - p = skb->data; - _put_byte(&p, 0); - _put_byte(&p, 0); - _put_byte(&p, SEND_REGISTER); - _put_word(&p, appl); - _put_word(&p, 1024 * (nconn + 1)); - _put_word(&p, nconn); - _put_word(&p, rp->datablkcnt); - _put_word(&p, rp->datablklen); - skb_put(skb, (u8 *)p - (u8 *)skb->data); - - b1dma_queue_tx(card, skb); -} - -/* ------------------------------------------------------------- */ - -void b1dma_release_appl(struct capi_ctr *ctrl, u16 appl) -{ - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - avmcard *card = cinfo->card; - struct sk_buff *skb; - void *p; - unsigned long flags; - - spin_lock_irqsave(&card->lock, flags); - capilib_release_appl(&cinfo->ncci_head, appl); - spin_unlock_irqrestore(&card->lock, flags); - - skb = alloc_skb(7, GFP_ATOMIC); - if (!skb) { - printk(KERN_CRIT "%s: no memory, lost release appl.\n", - card->name); - return; - } - p = skb->data; - _put_byte(&p, 0); - _put_byte(&p, 0); - _put_byte(&p, SEND_RELEASE); - _put_word(&p, appl); - - skb_put(skb, (u8 *)p - (u8 *)skb->data); - - b1dma_queue_tx(card, skb); -} - -/* ------------------------------------------------------------- */ - -u16 b1dma_send_message(struct capi_ctr *ctrl, struct sk_buff *skb) -{ - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - avmcard *card = cinfo->card; - u16 retval = CAPI_NOERROR; - - if (CAPIMSG_CMD(skb->data) == CAPI_DATA_B3_REQ) { - unsigned long flags; - spin_lock_irqsave(&card->lock, flags); - retval = capilib_data_b3_req(&cinfo->ncci_head, - CAPIMSG_APPID(skb->data), - CAPIMSG_NCCI(skb->data), - CAPIMSG_MSGID(skb->data)); - spin_unlock_irqrestore(&card->lock, flags); - } - if (retval == CAPI_NOERROR) - b1dma_queue_tx(card, skb); - - return retval; -} - -/* ------------------------------------------------------------- */ - -int b1dma_proc_show(struct seq_file *m, void *v) -{ - struct capi_ctr *ctrl = m->private; - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - avmcard *card = cinfo->card; - u8 flag; - char *s; - u32 txoff, txlen, rxoff, rxlen, csr; - unsigned long flags; - - seq_printf(m, "%-16s %s\n", "name", card->name); - seq_printf(m, "%-16s 0x%x\n", "io", card->port); - seq_printf(m, "%-16s %d\n", "irq", card->irq); - seq_printf(m, "%-16s 0x%lx\n", "membase", card->membase); - switch (card->cardtype) { - case avm_b1isa: s = "B1 ISA"; break; - case avm_b1pci: s = "B1 PCI"; break; - case avm_b1pcmcia: s = "B1 PCMCIA"; break; - case avm_m1: s = "M1"; break; - case avm_m2: s = "M2"; break; - case avm_t1isa: s = "T1 ISA (HEMA)"; break; - case avm_t1pci: s = "T1 PCI"; break; - case avm_c4: s = "C4"; break; - case avm_c2: s = "C2"; break; - default: s = "???"; break; - } - seq_printf(m, "%-16s %s\n", "type", s); - if ((s = cinfo->version[VER_DRIVER]) != NULL) - seq_printf(m, "%-16s %s\n", "ver_driver", s); - if ((s = cinfo->version[VER_CARDTYPE]) != NULL) - seq_printf(m, "%-16s %s\n", "ver_cardtype", s); - if ((s = cinfo->version[VER_SERIAL]) != NULL) - seq_printf(m, "%-16s %s\n", "ver_serial", s); - - if (card->cardtype != avm_m1) { - flag = ((u8 *)(ctrl->profile.manu))[3]; - if (flag) - seq_printf(m, "%-16s%s%s%s%s%s%s%s\n", - "protocol", - (flag & 0x01) ? " DSS1" : "", - (flag & 0x02) ? " CT1" : "", - (flag & 0x04) ? " VN3" : "", - (flag & 0x08) ? " NI1" : "", - (flag & 0x10) ? " AUSTEL" : "", - (flag & 0x20) ? " ESS" : "", - (flag & 0x40) ? " 1TR6" : "" - ); - } - if (card->cardtype != avm_m1) { - flag = ((u8 *)(ctrl->profile.manu))[5]; - if (flag) - seq_printf(m, "%-16s%s%s%s%s\n", - "linetype", - (flag & 0x01) ? " point to point" : "", - (flag & 0x02) ? " point to multipoint" : "", - (flag & 0x08) ? " leased line without D-channel" : "", - (flag & 0x04) ? " leased line with D-channel" : "" - ); - } - seq_printf(m, "%-16s %s\n", "cardname", cinfo->cardname); - - - spin_lock_irqsave(&card->lock, flags); - - txoff = (dma_addr_t)b1dma_readl(card, AMCC_TXPTR)-card->dma->sendbuf.dmaaddr; - txlen = b1dma_readl(card, AMCC_TXLEN); - - rxoff = (dma_addr_t)b1dma_readl(card, AMCC_RXPTR)-card->dma->recvbuf.dmaaddr; - rxlen = b1dma_readl(card, AMCC_RXLEN); - - csr = b1dma_readl(card, AMCC_INTCSR); - - spin_unlock_irqrestore(&card->lock, flags); - - seq_printf(m, "%-16s 0x%lx\n", "csr (cached)", (unsigned long)card->csr); - seq_printf(m, "%-16s 0x%lx\n", "csr", (unsigned long)csr); - seq_printf(m, "%-16s %lu\n", "txoff", (unsigned long)txoff); - seq_printf(m, "%-16s %lu\n", "txlen", (unsigned long)txlen); - seq_printf(m, "%-16s %lu\n", "rxoff", (unsigned long)rxoff); - seq_printf(m, "%-16s %lu\n", "rxlen", (unsigned long)rxlen); - - return 0; -} -EXPORT_SYMBOL(b1dma_proc_show); - -/* ------------------------------------------------------------- */ - -EXPORT_SYMBOL(b1dma_reset); -EXPORT_SYMBOL(t1pci_detect); -EXPORT_SYMBOL(b1pciv4_detect); -EXPORT_SYMBOL(b1dma_interrupt); - -EXPORT_SYMBOL(b1dma_load_firmware); -EXPORT_SYMBOL(b1dma_reset_ctr); -EXPORT_SYMBOL(b1dma_register_appl); -EXPORT_SYMBOL(b1dma_release_appl); -EXPORT_SYMBOL(b1dma_send_message); - -static int __init b1dma_init(void) -{ - char *p; - char rev[32]; - - if ((p = strchr(revision, ':')) != NULL && p[1]) { - strlcpy(rev, p + 2, sizeof(rev)); - if ((p = strchr(rev, '$')) != NULL && p > rev) - *(p - 1) = 0; - } else - strcpy(rev, "1.0"); - - printk(KERN_INFO "b1dma: revision %s\n", rev); - - return 0; -} - -static void __exit b1dma_exit(void) -{ -} - -module_init(b1dma_init); -module_exit(b1dma_exit); diff --git a/drivers/staging/isdn/avm/b1isa.c b/drivers/staging/isdn/avm/b1isa.c deleted file mode 100644 index cdfea72e0ef6..000000000000 --- a/drivers/staging/isdn/avm/b1isa.c +++ /dev/null @@ -1,243 +0,0 @@ -/* $Id: b1isa.c,v 1.1.2.3 2004/02/10 01:07:12 keil Exp $ - * - * Module for AVM B1 ISA-card. - * - * Copyright 1999 by Carsten Paeth <calle@calle.de> - * - * This software may be used and distributed according to the terms - * of the GNU General Public License, incorporated herein by reference. - * - */ - -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/skbuff.h> -#include <linux/delay.h> -#include <linux/mm.h> -#include <linux/interrupt.h> -#include <linux/ioport.h> -#include <linux/capi.h> -#include <linux/init.h> -#include <linux/pci.h> -#include <asm/io.h> -#include <linux/isdn/capicmd.h> -#include <linux/isdn/capiutil.h> -#include <linux/isdn/capilli.h> -#include "avmcard.h" - -/* ------------------------------------------------------------- */ - -static char *revision = "$Revision: 1.1.2.3 $"; - -/* ------------------------------------------------------------- */ - -MODULE_DESCRIPTION("CAPI4Linux: Driver for AVM B1 ISA card"); -MODULE_AUTHOR("Carsten Paeth"); -MODULE_LICENSE("GPL"); - -/* ------------------------------------------------------------- */ - -static void b1isa_remove(struct pci_dev *pdev) -{ - avmctrl_info *cinfo = pci_get_drvdata(pdev); - avmcard *card; - - if (!cinfo) - return; - - card = cinfo->card; - - b1_reset(card->port); - b1_reset(card->port); - - detach_capi_ctr(&cinfo->capi_ctrl); - free_irq(card->irq, card); - release_region(card->port, AVMB1_PORTLEN); - b1_free_card(card); -} - -/* ------------------------------------------------------------- */ - -static char *b1isa_procinfo(struct capi_ctr *ctrl); - -static int b1isa_probe(struct pci_dev *pdev) -{ - avmctrl_info *cinfo; - avmcard *card; - int retval; - - card = b1_alloc_card(1); - if (!card) { - printk(KERN_WARNING "b1isa: no memory.\n"); - retval = -ENOMEM; - goto err; - } - - cinfo = card->ctrlinfo; - - card->port = pci_resource_start(pdev, 0); - card->irq = pdev->irq; - card->cardtype = avm_b1isa; - sprintf(card->name, "b1isa-%x", card->port); - - if (card->port != 0x150 && card->port != 0x250 - && card->port != 0x300 && card->port != 0x340) { - printk(KERN_WARNING "b1isa: invalid port 0x%x.\n", card->port); - retval = -EINVAL; - goto err_free; - } - if (b1_irq_table[card->irq & 0xf] == 0) { - printk(KERN_WARNING "b1isa: irq %d not valid.\n", card->irq); - retval = -EINVAL; - goto err_free; - } - if (!request_region(card->port, AVMB1_PORTLEN, card->name)) { - printk(KERN_WARNING "b1isa: ports 0x%03x-0x%03x in use.\n", - card->port, card->port + AVMB1_PORTLEN); - retval = -EBUSY; - goto err_free; - } - retval = request_irq(card->irq, b1_interrupt, 0, card->name, card); - if (retval) { - printk(KERN_ERR "b1isa: unable to get IRQ %d.\n", card->irq); - goto err_release_region; - } - b1_reset(card->port); - if ((retval = b1_detect(card->port, card->cardtype)) != 0) { - printk(KERN_NOTICE "b1isa: NO card at 0x%x (%d)\n", - card->port, retval); - retval = -ENODEV; - goto err_free_irq; - } - b1_reset(card->port); - b1_getrevision(card); - - cinfo->capi_ctrl.owner = THIS_MODULE; - cinfo->capi_ctrl.driver_name = "b1isa"; - cinfo->capi_ctrl.driverdata = cinfo; - cinfo->capi_ctrl.register_appl = b1_register_appl; - cinfo->capi_ctrl.release_appl = b1_release_appl; - cinfo->capi_ctrl.send_message = b1_send_message; - cinfo->capi_ctrl.load_firmware = b1_load_firmware; - cinfo->capi_ctrl.reset_ctr = b1_reset_ctr; - cinfo->capi_ctrl.procinfo = b1isa_procinfo; - cinfo->capi_ctrl.proc_show = b1_proc_show; - strcpy(cinfo->capi_ctrl.name, card->name); - - retval = attach_capi_ctr(&cinfo->capi_ctrl); - if (retval) { - printk(KERN_ERR "b1isa: attach controller failed.\n"); - goto err_free_irq; - } - - printk(KERN_INFO "b1isa: AVM B1 ISA at i/o %#x, irq %d, revision %d\n", - card->port, card->irq, card->revision); - - pci_set_drvdata(pdev, cinfo); - return 0; - -err_free_irq: - free_irq(card->irq, card); -err_release_region: - release_region(card->port, AVMB1_PORTLEN); -err_free: - b1_free_card(card); -err: - return retval; -} - -static char *b1isa_procinfo(struct capi_ctr *ctrl) -{ - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - - if (!cinfo) - return ""; - sprintf(cinfo->infobuf, "%s %s 0x%x %d r%d", - cinfo->cardname[0] ? cinfo->cardname : "-", - cinfo->version[VER_DRIVER] ? cinfo->version[VER_DRIVER] : "-", - cinfo->card ? cinfo->card->port : 0x0, - cinfo->card ? cinfo->card->irq : 0, - cinfo->card ? cinfo->card->revision : 0 - ); - return cinfo->infobuf; -} - -/* ------------------------------------------------------------- */ - -#define MAX_CARDS 4 -static struct pci_dev isa_dev[MAX_CARDS]; -static int io[MAX_CARDS]; -static int irq[MAX_CARDS]; - -module_param_hw_array(io, int, ioport, NULL, 0); -module_param_hw_array(irq, int, irq, NULL, 0); -MODULE_PARM_DESC(io, "I/O base address(es)"); -MODULE_PARM_DESC(irq, "IRQ number(s) (assigned)"); - -static int b1isa_add_card(struct capi_driver *driver, capicardparams *data) -{ - int i; - - for (i = 0; i < MAX_CARDS; i++) { - if (isa_dev[i].resource[0].start) - continue; - - isa_dev[i].resource[0].start = data->port; - isa_dev[i].irq = data->irq; - - if (b1isa_probe(&isa_dev[i]) == 0) - return 0; - } - return -ENODEV; -} - -static struct capi_driver capi_driver_b1isa = { - .name = "b1isa", - .revision = "1.0", - .add_card = b1isa_add_card, -}; - -static int __init b1isa_init(void) -{ - char *p; - char rev[32]; - int i; - - if ((p = strchr(revision, ':')) != NULL && p[1]) { - strlcpy(rev, p + 2, 32); - if ((p = strchr(rev, '$')) != NULL && p > rev) - *(p - 1) = 0; - } else - strcpy(rev, "1.0"); - - for (i = 0; i < MAX_CARDS; i++) { - if (!io[i]) - break; - - isa_dev[i].resource[0].start = io[i]; - isa_dev[i].irq = irq[i]; - - if (b1isa_probe(&isa_dev[i]) != 0) - return -ENODEV; - } - - strlcpy(capi_driver_b1isa.revision, rev, 32); - register_capi_driver(&capi_driver_b1isa); - printk(KERN_INFO "b1isa: revision %s\n", rev); - - return 0; -} - -static void __exit b1isa_exit(void) -{ - int i; - - for (i = 0; i < MAX_CARDS; i++) { - if (isa_dev[i].resource[0].start) - b1isa_remove(&isa_dev[i]); - } - unregister_capi_driver(&capi_driver_b1isa); -} - -module_init(b1isa_init); -module_exit(b1isa_exit); diff --git a/drivers/staging/isdn/avm/b1pci.c b/drivers/staging/isdn/avm/b1pci.c deleted file mode 100644 index b76b57a82c02..000000000000 --- a/drivers/staging/isdn/avm/b1pci.c +++ /dev/null @@ -1,416 +0,0 @@ -/* $Id: b1pci.c,v 1.1.2.2 2004/01/16 21:09:27 keil Exp $ - * - * Module for AVM B1 PCI-card. - * - * Copyright 1999 by Carsten Paeth <calle@calle.de> - * - * This software may be used and distributed according to the terms - * of the GNU General Public License, incorporated herein by reference. - * - */ - -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/skbuff.h> -#include <linux/delay.h> -#include <linux/mm.h> -#include <linux/interrupt.h> -#include <linux/ioport.h> -#include <linux/pci.h> -#include <linux/capi.h> -#include <asm/io.h> -#include <linux/init.h> -#include <linux/isdn/capicmd.h> -#include <linux/isdn/capiutil.h> -#include <linux/isdn/capilli.h> -#include "avmcard.h" - -/* ------------------------------------------------------------- */ - -static char *revision = "$Revision: 1.1.2.2 $"; - -/* ------------------------------------------------------------- */ - -static struct pci_device_id b1pci_pci_tbl[] = { - { PCI_VENDOR_ID_AVM, PCI_DEVICE_ID_AVM_B1, PCI_ANY_ID, PCI_ANY_ID }, - { } /* Terminating entry */ -}; - -MODULE_DEVICE_TABLE(pci, b1pci_pci_tbl); -MODULE_DESCRIPTION("CAPI4Linux: Driver for AVM B1 PCI card"); -MODULE_AUTHOR("Carsten Paeth"); -MODULE_LICENSE("GPL"); - -/* ------------------------------------------------------------- */ - -static char *b1pci_procinfo(struct capi_ctr *ctrl) -{ - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - - if (!cinfo) - return ""; - sprintf(cinfo->infobuf, "%s %s 0x%x %d r%d", - cinfo->cardname[0] ? cinfo->cardname : "-", - cinfo->version[VER_DRIVER] ? cinfo->version[VER_DRIVER] : "-", - cinfo->card ? cinfo->card->port : 0x0, - cinfo->card ? cinfo->card->irq : 0, - cinfo->card ? cinfo->card->revision : 0 - ); - return cinfo->infobuf; -} - -/* ------------------------------------------------------------- */ - -static int b1pci_probe(struct capicardparams *p, struct pci_dev *pdev) -{ - avmcard *card; - avmctrl_info *cinfo; - int retval; - - card = b1_alloc_card(1); - if (!card) { - printk(KERN_WARNING "b1pci: no memory.\n"); - retval = -ENOMEM; - goto err; - } - - cinfo = card->ctrlinfo; - sprintf(card->name, "b1pci-%x", p->port); - card->port = p->port; - card->irq = p->irq; - card->cardtype = avm_b1pci; - - if (!request_region(card->port, AVMB1_PORTLEN, card->name)) { - printk(KERN_WARNING "b1pci: ports 0x%03x-0x%03x in use.\n", - card->port, card->port + AVMB1_PORTLEN); - retval = -EBUSY; - goto err_free; - } - b1_reset(card->port); - retval = b1_detect(card->port, card->cardtype); - if (retval) { - printk(KERN_NOTICE "b1pci: NO card at 0x%x (%d)\n", - card->port, retval); - retval = -ENODEV; - goto err_release_region; - } - b1_reset(card->port); - b1_getrevision(card); - - retval = request_irq(card->irq, b1_interrupt, IRQF_SHARED, card->name, card); - if (retval) { - printk(KERN_ERR "b1pci: unable to get IRQ %d.\n", card->irq); - retval = -EBUSY; - goto err_release_region; - } - - cinfo->capi_ctrl.driver_name = "b1pci"; - cinfo->capi_ctrl.driverdata = cinfo; - cinfo->capi_ctrl.register_appl = b1_register_appl; - cinfo->capi_ctrl.release_appl = b1_release_appl; - cinfo->capi_ctrl.send_message = b1_send_message; - cinfo->capi_ctrl.load_firmware = b1_load_firmware; - cinfo->capi_ctrl.reset_ctr = b1_reset_ctr; - cinfo->capi_ctrl.procinfo = b1pci_procinfo; - cinfo->capi_ctrl.proc_show = b1_proc_show; - strcpy(cinfo->capi_ctrl.name, card->name); - cinfo->capi_ctrl.owner = THIS_MODULE; - - retval = attach_capi_ctr(&cinfo->capi_ctrl); - if (retval) { - printk(KERN_ERR "b1pci: attach controller failed.\n"); - goto err_free_irq; - } - - if (card->revision >= 4) { - printk(KERN_INFO "b1pci: AVM B1 PCI V4 at i/o %#x, irq %d, revision %d (no dma)\n", - card->port, card->irq, card->revision); - } else { - printk(KERN_INFO "b1pci: AVM B1 PCI at i/o %#x, irq %d, revision %d\n", - card->port, card->irq, card->revision); - } - - pci_set_drvdata(pdev, card); - return 0; - -err_free_irq: - free_irq(card->irq, card); -err_release_region: - release_region(card->port, AVMB1_PORTLEN); -err_free: - b1_free_card(card); -err: - return retval; -} - -static void b1pci_remove(struct pci_dev *pdev) -{ - avmcard *card = pci_get_drvdata(pdev); - avmctrl_info *cinfo = card->ctrlinfo; - unsigned int port = card->port; - - b1_reset(port); - b1_reset(port); - - detach_capi_ctr(&cinfo->capi_ctrl); - free_irq(card->irq, card); - release_region(card->port, AVMB1_PORTLEN); - b1_free_card(card); -} - -#ifdef CONFIG_ISDN_DRV_AVMB1_B1PCIV4 -/* ------------------------------------------------------------- */ - -static char *b1pciv4_procinfo(struct capi_ctr *ctrl) -{ - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - - if (!cinfo) - return ""; - sprintf(cinfo->infobuf, "%s %s 0x%x %d 0x%lx r%d", - cinfo->cardname[0] ? cinfo->cardname : "-", - cinfo->version[VER_DRIVER] ? cinfo->version[VER_DRIVER] : "-", - cinfo->card ? cinfo->card->port : 0x0, - cinfo->card ? cinfo->card->irq : 0, - cinfo->card ? cinfo->card->membase : 0, - cinfo->card ? cinfo->card->revision : 0 - ); - return cinfo->infobuf; -} - -/* ------------------------------------------------------------- */ - -static int b1pciv4_probe(struct capicardparams *p, struct pci_dev *pdev) -{ - avmcard *card; - avmctrl_info *cinfo; - int retval; - - card = b1_alloc_card(1); - if (!card) { - printk(KERN_WARNING "b1pci: no memory.\n"); - retval = -ENOMEM; - goto err; - } - - card->dma = avmcard_dma_alloc("b1pci", pdev, 2048 + 128, 2048 + 128); - if (!card->dma) { - printk(KERN_WARNING "b1pci: dma alloc.\n"); - retval = -ENOMEM; - goto err_free; - } - - cinfo = card->ctrlinfo; - sprintf(card->name, "b1pciv4-%x", p->port); - card->port = p->port; - card->irq = p->irq; - card->membase = p->membase; - card->cardtype = avm_b1pci; - - if (!request_region(card->port, AVMB1_PORTLEN, card->name)) { - printk(KERN_WARNING "b1pci: ports 0x%03x-0x%03x in use.\n", - card->port, card->port + AVMB1_PORTLEN); - retval = -EBUSY; - goto err_free_dma; - } - - card->mbase = ioremap(card->membase, 64); - if (!card->mbase) { - printk(KERN_NOTICE "b1pci: can't remap memory at 0x%lx\n", - card->membase); - retval = -ENOMEM; - goto err_release_region; - } - - b1dma_reset(card); - - retval = b1pciv4_detect(card); - if (retval) { - printk(KERN_NOTICE "b1pci: NO card at 0x%x (%d)\n", - card->port, retval); - retval = -ENODEV; - goto err_unmap; - } - b1dma_reset(card); - b1_getrevision(card); - - retval = request_irq(card->irq, b1dma_interrupt, IRQF_SHARED, card->name, card); - if (retval) { - printk(KERN_ERR "b1pci: unable to get IRQ %d.\n", - card->irq); - retval = -EBUSY; - goto err_unmap; - } - - cinfo->capi_ctrl.owner = THIS_MODULE; - cinfo->capi_ctrl.driver_name = "b1pciv4"; - cinfo->capi_ctrl.driverdata = cinfo; - cinfo->capi_ctrl.register_appl = b1dma_register_appl; - cinfo->capi_ctrl.release_appl = b1dma_release_appl; - cinfo->capi_ctrl.send_message = b1dma_send_message; - cinfo->capi_ctrl.load_firmware = b1dma_load_firmware; - cinfo->capi_ctrl.reset_ctr = b1dma_reset_ctr; - cinfo->capi_ctrl.procinfo = b1pciv4_procinfo; - cinfo->capi_ctrl.proc_show = b1dma_proc_show; - strcpy(cinfo->capi_ctrl.name, card->name); - - retval = attach_capi_ctr(&cinfo->capi_ctrl); - if (retval) { - printk(KERN_ERR "b1pci: attach controller failed.\n"); - goto err_free_irq; - } - card->cardnr = cinfo->capi_ctrl.cnr; - - printk(KERN_INFO "b1pci: AVM B1 PCI V4 at i/o %#x, irq %d, mem %#lx, revision %d (dma)\n", - card->port, card->irq, card->membase, card->revision); - - pci_set_drvdata(pdev, card); - return 0; - -err_free_irq: - free_irq(card->irq, card); -err_unmap: - iounmap(card->mbase); -err_release_region: - release_region(card->port, AVMB1_PORTLEN); -err_free_dma: - avmcard_dma_free(card->dma); -err_free: - b1_free_card(card); -err: - return retval; - -} - -static void b1pciv4_remove(struct pci_dev *pdev) -{ - avmcard *card = pci_get_drvdata(pdev); - avmctrl_info *cinfo = card->ctrlinfo; - - b1dma_reset(card); - - detach_capi_ctr(&cinfo->capi_ctrl); - free_irq(card->irq, card); - iounmap(card->mbase); - release_region(card->port, AVMB1_PORTLEN); - avmcard_dma_free(card->dma); - b1_free_card(card); -} - -#endif /* CONFIG_ISDN_DRV_AVMB1_B1PCIV4 */ - -static int b1pci_pci_probe(struct pci_dev *pdev, - const struct pci_device_id *ent) -{ - struct capicardparams param; - int retval; - - if (pci_enable_device(pdev) < 0) { - printk(KERN_ERR "b1pci: failed to enable AVM-B1\n"); - return -ENODEV; - } - param.irq = pdev->irq; - - if (pci_resource_start(pdev, 2)) { /* B1 PCI V4 */ -#ifdef CONFIG_ISDN_DRV_AVMB1_B1PCIV4 - pci_set_master(pdev); -#endif - param.membase = pci_resource_start(pdev, 0); - param.port = pci_resource_start(pdev, 2); - - printk(KERN_INFO "b1pci: PCI BIOS reports AVM-B1 V4 at i/o %#x, irq %d, mem %#x\n", - param.port, param.irq, param.membase); -#ifdef CONFIG_ISDN_DRV_AVMB1_B1PCIV4 - retval = b1pciv4_probe(¶m, pdev); -#else - retval = b1pci_probe(¶m, pdev); -#endif - if (retval != 0) { - printk(KERN_ERR "b1pci: no AVM-B1 V4 at i/o %#x, irq %d, mem %#x detected\n", - param.port, param.irq, param.membase); - } - } else { - param.membase = 0; - param.port = pci_resource_start(pdev, 1); - - printk(KERN_INFO "b1pci: PCI BIOS reports AVM-B1 at i/o %#x, irq %d\n", - param.port, param.irq); - retval = b1pci_probe(¶m, pdev); - if (retval != 0) { - printk(KERN_ERR "b1pci: no AVM-B1 at i/o %#x, irq %d detected\n", - param.port, param.irq); - } - } - return retval; -} - -static void b1pci_pci_remove(struct pci_dev *pdev) -{ -#ifdef CONFIG_ISDN_DRV_AVMB1_B1PCIV4 - avmcard *card = pci_get_drvdata(pdev); - - if (card->dma) - b1pciv4_remove(pdev); - else - b1pci_remove(pdev); -#else - b1pci_remove(pdev); -#endif -} - -static struct pci_driver b1pci_pci_driver = { - .name = "b1pci", - .id_table = b1pci_pci_tbl, - .probe = b1pci_pci_probe, - .remove = b1pci_pci_remove, -}; - -static struct capi_driver capi_driver_b1pci = { - .name = "b1pci", - .revision = "1.0", -}; -#ifdef CONFIG_ISDN_DRV_AVMB1_B1PCIV4 -static struct capi_driver capi_driver_b1pciv4 = { - .name = "b1pciv4", - .revision = "1.0", -}; -#endif - -static int __init b1pci_init(void) -{ - char *p; - char rev[32]; - int err; - - if ((p = strchr(revision, ':')) != NULL && p[1]) { - strlcpy(rev, p + 2, 32); - if ((p = strchr(rev, '$')) != NULL && p > rev) - *(p - 1) = 0; - } else - strcpy(rev, "1.0"); - - - err = pci_register_driver(&b1pci_pci_driver); - if (!err) { - strlcpy(capi_driver_b1pci.revision, rev, 32); - register_capi_driver(&capi_driver_b1pci); -#ifdef CONFIG_ISDN_DRV_AVMB1_B1PCIV4 - strlcpy(capi_driver_b1pciv4.revision, rev, 32); - register_capi_driver(&capi_driver_b1pciv4); -#endif - printk(KERN_INFO "b1pci: revision %s\n", rev); - } - return err; -} - -static void __exit b1pci_exit(void) -{ - unregister_capi_driver(&capi_driver_b1pci); -#ifdef CONFIG_ISDN_DRV_AVMB1_B1PCIV4 - unregister_capi_driver(&capi_driver_b1pciv4); -#endif - pci_unregister_driver(&b1pci_pci_driver); -} - -module_init(b1pci_init); -module_exit(b1pci_exit); diff --git a/drivers/staging/isdn/avm/b1pcmcia.c b/drivers/staging/isdn/avm/b1pcmcia.c deleted file mode 100644 index 3aca16e62902..000000000000 --- a/drivers/staging/isdn/avm/b1pcmcia.c +++ /dev/null @@ -1,224 +0,0 @@ -/* $Id: b1pcmcia.c,v 1.1.2.2 2004/01/16 21:09:27 keil Exp $ - * - * Module for AVM B1/M1/M2 PCMCIA-card. - * - * Copyright 1999 by Carsten Paeth <calle@calle.de> - * - * This software may be used and distributed according to the terms - * of the GNU General Public License, incorporated herein by reference. - * - */ - -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/skbuff.h> -#include <linux/delay.h> -#include <linux/mm.h> -#include <linux/interrupt.h> -#include <linux/ioport.h> -#include <linux/init.h> -#include <asm/io.h> -#include <linux/capi.h> -#include <linux/b1pcmcia.h> -#include <linux/isdn/capicmd.h> -#include <linux/isdn/capiutil.h> -#include <linux/isdn/capilli.h> -#include "avmcard.h" - -/* ------------------------------------------------------------- */ - -static char *revision = "$Revision: 1.1.2.2 $"; - -/* ------------------------------------------------------------- */ - -MODULE_DESCRIPTION("CAPI4Linux: Driver for AVM PCMCIA cards"); -MODULE_AUTHOR("Carsten Paeth"); -MODULE_LICENSE("GPL"); - -/* ------------------------------------------------------------- */ - -static void b1pcmcia_remove_ctr(struct capi_ctr *ctrl) -{ - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - avmcard *card = cinfo->card; - unsigned int port = card->port; - - b1_reset(port); - b1_reset(port); - - detach_capi_ctr(ctrl); - free_irq(card->irq, card); - b1_free_card(card); -} - -/* ------------------------------------------------------------- */ - -static LIST_HEAD(cards); - -static char *b1pcmcia_procinfo(struct capi_ctr *ctrl); - -static int b1pcmcia_add_card(unsigned int port, unsigned irq, - enum avmcardtype cardtype) -{ - avmctrl_info *cinfo; - avmcard *card; - char *cardname; - int retval; - - card = b1_alloc_card(1); - if (!card) { - printk(KERN_WARNING "b1pcmcia: no memory.\n"); - retval = -ENOMEM; - goto err; - } - cinfo = card->ctrlinfo; - - switch (cardtype) { - case avm_m1: sprintf(card->name, "m1-%x", port); break; - case avm_m2: sprintf(card->name, "m2-%x", port); break; - default: sprintf(card->name, "b1pcmcia-%x", port); break; - } - card->port = port; - card->irq = irq; - card->cardtype = cardtype; - - retval = request_irq(card->irq, b1_interrupt, IRQF_SHARED, card->name, card); - if (retval) { - printk(KERN_ERR "b1pcmcia: unable to get IRQ %d.\n", - card->irq); - retval = -EBUSY; - goto err_free; - } - b1_reset(card->port); - if ((retval = b1_detect(card->port, card->cardtype)) != 0) { - printk(KERN_NOTICE "b1pcmcia: NO card at 0x%x (%d)\n", - card->port, retval); - retval = -ENODEV; - goto err_free_irq; - } - b1_reset(card->port); - b1_getrevision(card); - - cinfo->capi_ctrl.owner = THIS_MODULE; - cinfo->capi_ctrl.driver_name = "b1pcmcia"; - cinfo->capi_ctrl.driverdata = cinfo; - cinfo->capi_ctrl.register_appl = b1_register_appl; - cinfo->capi_ctrl.release_appl = b1_release_appl; - cinfo->capi_ctrl.send_message = b1_send_message; - cinfo->capi_ctrl.load_firmware = b1_load_firmware; - cinfo->capi_ctrl.reset_ctr = b1_reset_ctr; - cinfo->capi_ctrl.procinfo = b1pcmcia_procinfo; - cinfo->capi_ctrl.proc_show = b1_proc_show; - strcpy(cinfo->capi_ctrl.name, card->name); - - retval = attach_capi_ctr(&cinfo->capi_ctrl); - if (retval) { - printk(KERN_ERR "b1pcmcia: attach controller failed.\n"); - goto err_free_irq; - } - switch (cardtype) { - case avm_m1: cardname = "M1"; break; - case avm_m2: cardname = "M2"; break; - default: cardname = "B1 PCMCIA"; break; - } - - printk(KERN_INFO "b1pcmcia: AVM %s at i/o %#x, irq %d, revision %d\n", - cardname, card->port, card->irq, card->revision); - - list_add(&card->list, &cards); - return cinfo->capi_ctrl.cnr; - -err_free_irq: - free_irq(card->irq, card); -err_free: - b1_free_card(card); -err: - return retval; -} - -/* ------------------------------------------------------------- */ - -static char *b1pcmcia_procinfo(struct capi_ctr *ctrl) -{ - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - - if (!cinfo) - return ""; - sprintf(cinfo->infobuf, "%s %s 0x%x %d r%d", - cinfo->cardname[0] ? cinfo->cardname : "-", - cinfo->version[VER_DRIVER] ? cinfo->version[VER_DRIVER] : "-", - cinfo->card ? cinfo->card->port : 0x0, - cinfo->card ? cinfo->card->irq : 0, - cinfo->card ? cinfo->card->revision : 0 - ); - return cinfo->infobuf; -} - -/* ------------------------------------------------------------- */ - -int b1pcmcia_addcard_b1(unsigned int port, unsigned irq) -{ - return b1pcmcia_add_card(port, irq, avm_b1pcmcia); -} - -int b1pcmcia_addcard_m1(unsigned int port, unsigned irq) -{ - return b1pcmcia_add_card(port, irq, avm_m1); -} - -int b1pcmcia_addcard_m2(unsigned int port, unsigned irq) -{ - return b1pcmcia_add_card(port, irq, avm_m2); -} - -int b1pcmcia_delcard(unsigned int port, unsigned irq) -{ - struct list_head *l; - avmcard *card; - - list_for_each(l, &cards) { - card = list_entry(l, avmcard, list); - if (card->port == port && card->irq == irq) { - b1pcmcia_remove_ctr(&card->ctrlinfo[0].capi_ctrl); - return 0; - } - } - return -ESRCH; -} - -EXPORT_SYMBOL(b1pcmcia_addcard_b1); -EXPORT_SYMBOL(b1pcmcia_addcard_m1); -EXPORT_SYMBOL(b1pcmcia_addcard_m2); -EXPORT_SYMBOL(b1pcmcia_delcard); - -static struct capi_driver capi_driver_b1pcmcia = { - .name = "b1pcmcia", - .revision = "1.0", -}; - -static int __init b1pcmcia_init(void) -{ - char *p; - char rev[32]; - - if ((p = strchr(revision, ':')) != NULL && p[1]) { - strlcpy(rev, p + 2, 32); - if ((p = strchr(rev, '$')) != NULL && p > rev) - *(p - 1) = 0; - } else - strcpy(rev, "1.0"); - - strlcpy(capi_driver_b1pcmcia.revision, rev, 32); - register_capi_driver(&capi_driver_b1pcmcia); - printk(KERN_INFO "b1pci: revision %s\n", rev); - - return 0; -} - -static void __exit b1pcmcia_exit(void) -{ - unregister_capi_driver(&capi_driver_b1pcmcia); -} - -module_init(b1pcmcia_init); -module_exit(b1pcmcia_exit); diff --git a/drivers/staging/isdn/avm/c4.c b/drivers/staging/isdn/avm/c4.c deleted file mode 100644 index ac72cd204c4d..000000000000 --- a/drivers/staging/isdn/avm/c4.c +++ /dev/null @@ -1,1317 +0,0 @@ -/* $Id: c4.c,v 1.1.2.2 2004/01/16 21:09:27 keil Exp $ - * - * Module for AVM C4 & C2 card. - * - * Copyright 1999 by Carsten Paeth <calle@calle.de> - * - * This software may be used and distributed according to the terms - * of the GNU General Public License, incorporated herein by reference. - * - */ - -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/proc_fs.h> -#include <linux/seq_file.h> -#include <linux/skbuff.h> -#include <linux/delay.h> -#include <linux/mm.h> -#include <linux/interrupt.h> -#include <linux/ioport.h> -#include <linux/pci.h> -#include <linux/capi.h> -#include <linux/kernelcapi.h> -#include <linux/init.h> -#include <linux/gfp.h> -#include <asm/io.h> -#include <linux/uaccess.h> -#include <linux/netdevice.h> -#include <linux/isdn/capicmd.h> -#include <linux/isdn/capiutil.h> -#include <linux/isdn/capilli.h> -#include "avmcard.h" - -#undef AVM_C4_DEBUG -#undef AVM_C4_POLLDEBUG - -/* ------------------------------------------------------------- */ - -static char *revision = "$Revision: 1.1.2.2 $"; - -/* ------------------------------------------------------------- */ - -static bool suppress_pollack; - -static const struct pci_device_id c4_pci_tbl[] = { - { PCI_VENDOR_ID_DEC, PCI_DEVICE_ID_DEC_21285, PCI_VENDOR_ID_AVM, PCI_DEVICE_ID_AVM_C4, 0, 0, (unsigned long)4 }, - { PCI_VENDOR_ID_DEC, PCI_DEVICE_ID_DEC_21285, PCI_VENDOR_ID_AVM, PCI_DEVICE_ID_AVM_C2, 0, 0, (unsigned long)2 }, - { } /* Terminating entry */ -}; - -MODULE_DEVICE_TABLE(pci, c4_pci_tbl); -MODULE_DESCRIPTION("CAPI4Linux: Driver for AVM C2/C4 cards"); -MODULE_AUTHOR("Carsten Paeth"); -MODULE_LICENSE("GPL"); -module_param(suppress_pollack, bool, 0); - -/* ------------------------------------------------------------- */ - -static void c4_dispatch_tx(avmcard *card); - -/* ------------------------------------------------------------- */ - -#define DC21285_DRAM_A0MR 0x40000000 -#define DC21285_DRAM_A1MR 0x40004000 -#define DC21285_DRAM_A2MR 0x40008000 -#define DC21285_DRAM_A3MR 0x4000C000 - -#define CAS_OFFSET 0x88 - -#define DC21285_ARMCSR_BASE 0x42000000 - -#define PCI_OUT_INT_STATUS 0x30 -#define PCI_OUT_INT_MASK 0x34 -#define MAILBOX_0 0x50 -#define MAILBOX_1 0x54 -#define MAILBOX_2 0x58 -#define MAILBOX_3 0x5C -#define DOORBELL 0x60 -#define DOORBELL_SETUP 0x64 - -#define CHAN_1_CONTROL 0x90 -#define CHAN_2_CONTROL 0xB0 -#define DRAM_TIMING 0x10C -#define DRAM_ADDR_SIZE_0 0x110 -#define DRAM_ADDR_SIZE_1 0x114 -#define DRAM_ADDR_SIZE_2 0x118 -#define DRAM_ADDR_SIZE_3 0x11C -#define SA_CONTROL 0x13C -#define XBUS_CYCLE 0x148 -#define XBUS_STROBE 0x14C -#define DBELL_PCI_MASK 0x150 -#define DBELL_SA_MASK 0x154 - -#define SDRAM_SIZE 0x1000000 - -/* ------------------------------------------------------------- */ - -#define MBOX_PEEK_POKE MAILBOX_0 - -#define DBELL_ADDR 0x01 -#define DBELL_DATA 0x02 -#define DBELL_RNWR 0x40 -#define DBELL_INIT 0x80 - -/* ------------------------------------------------------------- */ - -#define MBOX_UP_ADDR MAILBOX_0 -#define MBOX_UP_LEN MAILBOX_1 -#define MBOX_DOWN_ADDR MAILBOX_2 -#define MBOX_DOWN_LEN MAILBOX_3 - -#define DBELL_UP_HOST 0x00000100 -#define DBELL_UP_ARM 0x00000200 -#define DBELL_DOWN_HOST 0x00000400 -#define DBELL_DOWN_ARM 0x00000800 -#define DBELL_RESET_HOST 0x40000000 -#define DBELL_RESET_ARM 0x80000000 - -/* ------------------------------------------------------------- */ - -#define DRAM_TIMING_DEF 0x001A01A5 -#define DRAM_AD_SZ_DEF0 0x00000045 -#define DRAM_AD_SZ_NULL 0x00000000 - -#define SA_CTL_ALLRIGHT 0x64AA0271 - -#define INIT_XBUS_CYCLE 0x100016DB -#define INIT_XBUS_STROBE 0xF1F1F1F1 - -/* ------------------------------------------------------------- */ - -#define RESET_TIMEOUT (15 * HZ) /* 15 sec */ -#define PEEK_POKE_TIMEOUT (HZ / 10) /* 0.1 sec */ - -/* ------------------------------------------------------------- */ - -#define c4outmeml(addr, value) writel(value, addr) -#define c4inmeml(addr) readl(addr) -#define c4outmemw(addr, value) writew(value, addr) -#define c4inmemw(addr) readw(addr) -#define c4outmemb(addr, value) writeb(value, addr) -#define c4inmemb(addr) readb(addr) - -/* ------------------------------------------------------------- */ - -static inline int wait_for_doorbell(avmcard *card, unsigned long t) -{ - unsigned long stop; - - stop = jiffies + t; - while (c4inmeml(card->mbase + DOORBELL) != 0xffffffff) { - if (!time_before(jiffies, stop)) - return -1; - mb(); - } - return 0; -} - -static int c4_poke(avmcard *card, unsigned long off, unsigned long value) -{ - - if (wait_for_doorbell(card, HZ / 10) < 0) - return -1; - - c4outmeml(card->mbase + MBOX_PEEK_POKE, off); - c4outmeml(card->mbase + DOORBELL, DBELL_ADDR); - - if (wait_for_doorbell(card, HZ / 10) < 0) - return -1; - - c4outmeml(card->mbase + MBOX_PEEK_POKE, value); - c4outmeml(card->mbase + DOORBELL, DBELL_DATA | DBELL_ADDR); - - return 0; -} - -static int c4_peek(avmcard *card, unsigned long off, unsigned long *valuep) -{ - if (wait_for_doorbell(card, HZ / 10) < 0) - return -1; - - c4outmeml(card->mbase + MBOX_PEEK_POKE, off); - c4outmeml(card->mbase + DOORBELL, DBELL_RNWR | DBELL_ADDR); - - if (wait_for_doorbell(card, HZ / 10) < 0) - return -1; - - *valuep = c4inmeml(card->mbase + MBOX_PEEK_POKE); - - return 0; -} - -/* ------------------------------------------------------------- */ - -static int c4_load_t4file(avmcard *card, capiloaddatapart *t4file) -{ - u32 val; - unsigned char *dp; - u_int left; - u32 loadoff = 0; - - dp = t4file->data; - left = t4file->len; - while (left >= sizeof(u32)) { - if (t4file->user) { - if (copy_from_user(&val, dp, sizeof(val))) - return -EFAULT; - } else { - memcpy(&val, dp, sizeof(val)); - } - if (c4_poke(card, loadoff, val)) { - printk(KERN_ERR "%s: corrupted firmware file ?\n", - card->name); - return -EIO; - } - left -= sizeof(u32); - dp += sizeof(u32); - loadoff += sizeof(u32); - } - if (left) { - val = 0; - if (t4file->user) { - if (copy_from_user(&val, dp, left)) - return -EFAULT; - } else { - memcpy(&val, dp, left); - } - if (c4_poke(card, loadoff, val)) { - printk(KERN_ERR "%s: corrupted firmware file ?\n", - card->name); - return -EIO; - } - } - return 0; -} - -/* ------------------------------------------------------------- */ - -static inline void _put_byte(void **pp, u8 val) -{ - u8 *s = *pp; - *s++ = val; - *pp = s; -} - -static inline void _put_word(void **pp, u32 val) -{ - u8 *s = *pp; - *s++ = val & 0xff; - *s++ = (val >> 8) & 0xff; - *s++ = (val >> 16) & 0xff; - *s++ = (val >> 24) & 0xff; - *pp = s; -} - -static inline void _put_slice(void **pp, unsigned char *dp, unsigned int len) -{ - unsigned i = len; - _put_word(pp, i); - while (i-- > 0) - _put_byte(pp, *dp++); -} - -static inline u8 _get_byte(void **pp) -{ - u8 *s = *pp; - u8 val; - val = *s++; - *pp = s; - return val; -} - -static inline u32 _get_word(void **pp) -{ - u8 *s = *pp; - u32 val; - val = *s++; - val |= (*s++ << 8); - val |= (*s++ << 16); - val |= (*s++ << 24); - *pp = s; - return val; -} - -static inline u32 _get_slice(void **pp, unsigned char *dp) -{ - unsigned int len, i; - - len = i = _get_word(pp); - while (i-- > 0) *dp++ = _get_byte(pp); - return len; -} - -/* ------------------------------------------------------------- */ - -static void c4_reset(avmcard *card) -{ - unsigned long stop; - - c4outmeml(card->mbase + DOORBELL, DBELL_RESET_ARM); - - stop = jiffies + HZ * 10; - while (c4inmeml(card->mbase + DOORBELL) != 0xffffffff) { - if (!time_before(jiffies, stop)) - return; - c4outmeml(card->mbase + DOORBELL, DBELL_ADDR); - mb(); - } - - c4_poke(card, DC21285_ARMCSR_BASE + CHAN_1_CONTROL, 0); - c4_poke(card, DC21285_ARMCSR_BASE + CHAN_2_CONTROL, 0); -} - -/* ------------------------------------------------------------- */ - -static int c4_detect(avmcard *card) -{ - unsigned long stop, dummy; - - c4outmeml(card->mbase + PCI_OUT_INT_MASK, 0x0c); - if (c4inmeml(card->mbase + PCI_OUT_INT_MASK) != 0x0c) - return 1; - - c4outmeml(card->mbase + DOORBELL, DBELL_RESET_ARM); - - stop = jiffies + HZ * 10; - while (c4inmeml(card->mbase + DOORBELL) != 0xffffffff) { - if (!time_before(jiffies, stop)) - return 2; - c4outmeml(card->mbase + DOORBELL, DBELL_ADDR); - mb(); - } - - c4_poke(card, DC21285_ARMCSR_BASE + CHAN_1_CONTROL, 0); - c4_poke(card, DC21285_ARMCSR_BASE + CHAN_2_CONTROL, 0); - - c4outmeml(card->mbase + MAILBOX_0, 0x55aa55aa); - if (c4inmeml(card->mbase + MAILBOX_0) != 0x55aa55aa) return 3; - - c4outmeml(card->mbase + MAILBOX_0, 0xaa55aa55); - if (c4inmeml(card->mbase + MAILBOX_0) != 0xaa55aa55) return 4; - - if (c4_poke(card, DC21285_ARMCSR_BASE + DBELL_SA_MASK, 0)) return 5; - if (c4_poke(card, DC21285_ARMCSR_BASE + DBELL_PCI_MASK, 0)) return 6; - if (c4_poke(card, DC21285_ARMCSR_BASE + SA_CONTROL, SA_CTL_ALLRIGHT)) - return 7; - if (c4_poke(card, DC21285_ARMCSR_BASE + XBUS_CYCLE, INIT_XBUS_CYCLE)) - return 8; - if (c4_poke(card, DC21285_ARMCSR_BASE + XBUS_STROBE, INIT_XBUS_STROBE)) - return 8; - if (c4_poke(card, DC21285_ARMCSR_BASE + DRAM_TIMING, 0)) return 9; - - mdelay(1); - - if (c4_peek(card, DC21285_DRAM_A0MR, &dummy)) return 10; - if (c4_peek(card, DC21285_DRAM_A1MR, &dummy)) return 11; - if (c4_peek(card, DC21285_DRAM_A2MR, &dummy)) return 12; - if (c4_peek(card, DC21285_DRAM_A3MR, &dummy)) return 13; - - if (c4_poke(card, DC21285_DRAM_A0MR + CAS_OFFSET, 0)) return 14; - if (c4_poke(card, DC21285_DRAM_A1MR + CAS_OFFSET, 0)) return 15; - if (c4_poke(card, DC21285_DRAM_A2MR + CAS_OFFSET, 0)) return 16; - if (c4_poke(card, DC21285_DRAM_A3MR + CAS_OFFSET, 0)) return 17; - - mdelay(1); - - if (c4_poke(card, DC21285_ARMCSR_BASE + DRAM_TIMING, DRAM_TIMING_DEF)) - return 18; - - if (c4_poke(card, DC21285_ARMCSR_BASE + DRAM_ADDR_SIZE_0, DRAM_AD_SZ_DEF0)) - return 19; - if (c4_poke(card, DC21285_ARMCSR_BASE + DRAM_ADDR_SIZE_1, DRAM_AD_SZ_NULL)) - return 20; - if (c4_poke(card, DC21285_ARMCSR_BASE + DRAM_ADDR_SIZE_2, DRAM_AD_SZ_NULL)) - return 21; - if (c4_poke(card, DC21285_ARMCSR_BASE + DRAM_ADDR_SIZE_3, DRAM_AD_SZ_NULL)) - return 22; - - /* Transputer test */ - - if (c4_poke(card, 0x000000, 0x11111111) - || c4_poke(card, 0x400000, 0x22222222) - || c4_poke(card, 0x800000, 0x33333333) - || c4_poke(card, 0xC00000, 0x44444444)) - return 23; - - if (c4_peek(card, 0x000000, &dummy) || dummy != 0x11111111 - || c4_peek(card, 0x400000, &dummy) || dummy != 0x22222222 - || c4_peek(card, 0x800000, &dummy) || dummy != 0x33333333 - || c4_peek(card, 0xC00000, &dummy) || dummy != 0x44444444) - return 24; - - if (c4_poke(card, 0x000000, 0x55555555) - || c4_poke(card, 0x400000, 0x66666666) - || c4_poke(card, 0x800000, 0x77777777) - || c4_poke(card, 0xC00000, 0x88888888)) - return 25; - - if (c4_peek(card, 0x000000, &dummy) || dummy != 0x55555555 - || c4_peek(card, 0x400000, &dummy) || dummy != 0x66666666 - || c4_peek(card, 0x800000, &dummy) || dummy != 0x77777777 - || c4_peek(card, 0xC00000, &dummy) || dummy != 0x88888888) - return 26; - - return 0; -} - -/* ------------------------------------------------------------- */ - -static void c4_dispatch_tx(avmcard *card) -{ - avmcard_dmainfo *dma = card->dma; - struct sk_buff *skb; - u8 cmd, subcmd; - u16 len; - u32 txlen; - void *p; - - - if (card->csr & DBELL_DOWN_ARM) { /* tx busy */ - return; - } - - skb = skb_dequeue(&dma->send_queue); - if (!skb) { -#ifdef AVM_C4_DEBUG - printk(KERN_DEBUG "%s: tx underrun\n", card->name); -#endif - return; - } - - len = CAPIMSG_LEN(skb->data); - - if (len) { - cmd = CAPIMSG_COMMAND(skb->data); - subcmd = CAPIMSG_SUBCOMMAND(skb->data); - - p = dma->sendbuf.dmabuf; - - if (CAPICMD(cmd, subcmd) == CAPI_DATA_B3_REQ) { - u16 dlen = CAPIMSG_DATALEN(skb->data); - _put_byte(&p, SEND_DATA_B3_REQ); - _put_slice(&p, skb->data, len); - _put_slice(&p, skb->data + len, dlen); - } else { - _put_byte(&p, SEND_MESSAGE); - _put_slice(&p, skb->data, len); - } - txlen = (u8 *)p - (u8 *)dma->sendbuf.dmabuf; -#ifdef AVM_C4_DEBUG - printk(KERN_DEBUG "%s: tx put msg len=%d\n", card->name, txlen); -#endif - } else { - txlen = skb->len - 2; -#ifdef AVM_C4_POLLDEBUG - if (skb->data[2] == SEND_POLLACK) - printk(KERN_INFO "%s: ack to c4\n", card->name); -#endif -#ifdef AVM_C4_DEBUG - printk(KERN_DEBUG "%s: tx put 0x%x len=%d\n", - card->name, skb->data[2], txlen); -#endif - skb_copy_from_linear_data_offset(skb, 2, dma->sendbuf.dmabuf, - skb->len - 2); - } - txlen = (txlen + 3) & ~3; - - c4outmeml(card->mbase + MBOX_DOWN_ADDR, dma->sendbuf.dmaaddr); - c4outmeml(card->mbase + MBOX_DOWN_LEN, txlen); - - card->csr |= DBELL_DOWN_ARM; - - c4outmeml(card->mbase + DOORBELL, DBELL_DOWN_ARM); - - dev_kfree_skb_any(skb); -} - -/* ------------------------------------------------------------- */ - -static void queue_pollack(avmcard *card) -{ - struct sk_buff *skb; - void *p; - - skb = alloc_skb(3, GFP_ATOMIC); - if (!skb) { - printk(KERN_CRIT "%s: no memory, lost poll ack\n", - card->name); - return; - } - p = skb->data; - _put_byte(&p, 0); - _put_byte(&p, 0); - _put_byte(&p, SEND_POLLACK); - skb_put(skb, (u8 *)p - (u8 *)skb->data); - - skb_queue_tail(&card->dma->send_queue, skb); - c4_dispatch_tx(card); -} - -/* ------------------------------------------------------------- */ - -static void c4_handle_rx(avmcard *card) -{ - avmcard_dmainfo *dma = card->dma; - struct capi_ctr *ctrl; - avmctrl_info *cinfo; - struct sk_buff *skb; - void *p = dma->recvbuf.dmabuf; - u32 ApplId, MsgLen, DataB3Len, NCCI, WindowSize; - u8 b1cmd = _get_byte(&p); - u32 cidx; - - -#ifdef AVM_C4_DEBUG - printk(KERN_DEBUG "%s: rx 0x%x len=%lu\n", card->name, - b1cmd, (unsigned long)dma->recvlen); -#endif - - switch (b1cmd) { - case RECEIVE_DATA_B3_IND: - - ApplId = (unsigned) _get_word(&p); - MsgLen = _get_slice(&p, card->msgbuf); - DataB3Len = _get_slice(&p, card->databuf); - cidx = CAPIMSG_CONTROLLER(card->msgbuf)-card->cardnr; - if (cidx >= card->nlogcontr) cidx = 0; - ctrl = &card->ctrlinfo[cidx].capi_ctrl; - - if (MsgLen < 30) { /* not CAPI 64Bit */ - memset(card->msgbuf + MsgLen, 0, 30 - MsgLen); - MsgLen = 30; - CAPIMSG_SETLEN(card->msgbuf, 30); - } - if (!(skb = alloc_skb(DataB3Len + MsgLen, GFP_ATOMIC))) { - printk(KERN_ERR "%s: incoming packet dropped\n", - card->name); - } else { - skb_put_data(skb, card->msgbuf, MsgLen); - skb_put_data(skb, card->databuf, DataB3Len); - capi_ctr_handle_message(ctrl, ApplId, skb); - } - break; - - case RECEIVE_MESSAGE: - - ApplId = (unsigned) _get_word(&p); - MsgLen = _get_slice(&p, card->msgbuf); - cidx = CAPIMSG_CONTROLLER(card->msgbuf)-card->cardnr; - if (cidx >= card->nlogcontr) cidx = 0; - cinfo = &card->ctrlinfo[cidx]; - ctrl = &card->ctrlinfo[cidx].capi_ctrl; - - if (!(skb = alloc_skb(MsgLen, GFP_ATOMIC))) { - printk(KERN_ERR "%s: incoming packet dropped\n", - card->name); - } else { - skb_put_data(skb, card->msgbuf, MsgLen); - if (CAPIMSG_CMD(skb->data) == CAPI_DATA_B3_CONF) - capilib_data_b3_conf(&cinfo->ncci_head, ApplId, - CAPIMSG_NCCI(skb->data), - CAPIMSG_MSGID(skb->data)); - - capi_ctr_handle_message(ctrl, ApplId, skb); - } - break; - - case RECEIVE_NEW_NCCI: - - ApplId = _get_word(&p); - NCCI = _get_word(&p); - WindowSize = _get_word(&p); - cidx = (NCCI & 0x7f) - card->cardnr; - if (cidx >= card->nlogcontr) cidx = 0; - - capilib_new_ncci(&card->ctrlinfo[cidx].ncci_head, ApplId, NCCI, WindowSize); - - break; - - case RECEIVE_FREE_NCCI: - - ApplId = _get_word(&p); - NCCI = _get_word(&p); - - if (NCCI != 0xffffffff) { - cidx = (NCCI & 0x7f) - card->cardnr; - if (cidx >= card->nlogcontr) cidx = 0; - capilib_free_ncci(&card->ctrlinfo[cidx].ncci_head, ApplId, NCCI); - } - break; - - case RECEIVE_START: -#ifdef AVM_C4_POLLDEBUG - printk(KERN_INFO "%s: poll from c4\n", card->name); -#endif - if (!suppress_pollack) - queue_pollack(card); - for (cidx = 0; cidx < card->nr_controllers; cidx++) { - ctrl = &card->ctrlinfo[cidx].capi_ctrl; - capi_ctr_resume_output(ctrl); - } - break; - - case RECEIVE_STOP: - for (cidx = 0; cidx < card->nr_controllers; cidx++) { - ctrl = &card->ctrlinfo[cidx].capi_ctrl; - capi_ctr_suspend_output(ctrl); - } - break; - - case RECEIVE_INIT: - - cidx = card->nlogcontr; - if (cidx >= card->nr_controllers) { - printk(KERN_ERR "%s: card with %d controllers ??\n", - card->name, cidx + 1); - break; - } - card->nlogcontr++; - cinfo = &card->ctrlinfo[cidx]; - ctrl = &cinfo->capi_ctrl; - cinfo->versionlen = _get_slice(&p, cinfo->versionbuf); - b1_parse_version(cinfo); - printk(KERN_INFO "%s: %s-card (%s) now active\n", - card->name, - cinfo->version[VER_CARDTYPE], - cinfo->version[VER_DRIVER]); - capi_ctr_ready(&cinfo->capi_ctrl); - break; - - case RECEIVE_TASK_READY: - ApplId = (unsigned) _get_word(&p); - MsgLen = _get_slice(&p, card->msgbuf); - card->msgbuf[MsgLen] = 0; - while (MsgLen > 0 - && (card->msgbuf[MsgLen - 1] == '\n' - || card->msgbuf[MsgLen - 1] == '\r')) { - card->msgbuf[MsgLen - 1] = 0; - MsgLen--; - } - printk(KERN_INFO "%s: task %d \"%s\" ready.\n", - card->name, ApplId, card->msgbuf); - break; - - case RECEIVE_DEBUGMSG: - MsgLen = _get_slice(&p, card->msgbuf); - card->msgbuf[MsgLen] = 0; - while (MsgLen > 0 - && (card->msgbuf[MsgLen - 1] == '\n' - || card->msgbuf[MsgLen - 1] == '\r')) { - card->msgbuf[MsgLen - 1] = 0; - MsgLen--; - } - printk(KERN_INFO "%s: DEBUG: %s\n", card->name, card->msgbuf); - break; - - default: - printk(KERN_ERR "%s: c4_interrupt: 0x%x ???\n", - card->name, b1cmd); - return; - } -} - -/* ------------------------------------------------------------- */ - -static irqreturn_t c4_handle_interrupt(avmcard *card) -{ - unsigned long flags; - u32 status; - - spin_lock_irqsave(&card->lock, flags); - status = c4inmeml(card->mbase + DOORBELL); - - if (status & DBELL_RESET_HOST) { - u_int i; - c4outmeml(card->mbase + PCI_OUT_INT_MASK, 0x0c); - spin_unlock_irqrestore(&card->lock, flags); - if (card->nlogcontr == 0) - return IRQ_HANDLED; - printk(KERN_ERR "%s: unexpected reset\n", card->name); - for (i = 0; i < card->nr_controllers; i++) { - avmctrl_info *cinfo = &card->ctrlinfo[i]; - memset(cinfo->version, 0, sizeof(cinfo->version)); - spin_lock_irqsave(&card->lock, flags); - capilib_release(&cinfo->ncci_head); - spin_unlock_irqrestore(&card->lock, flags); - capi_ctr_down(&cinfo->capi_ctrl); - } - card->nlogcontr = 0; - return IRQ_HANDLED; - } - - status &= (DBELL_UP_HOST | DBELL_DOWN_HOST); - if (!status) { - spin_unlock_irqrestore(&card->lock, flags); - return IRQ_HANDLED; - } - c4outmeml(card->mbase + DOORBELL, status); - - if ((status & DBELL_UP_HOST) != 0) { - card->dma->recvlen = c4inmeml(card->mbase + MBOX_UP_LEN); - c4outmeml(card->mbase + MBOX_UP_LEN, 0); - c4_handle_rx(card); - card->dma->recvlen = 0; - c4outmeml(card->mbase + MBOX_UP_LEN, card->dma->recvbuf.size); - c4outmeml(card->mbase + DOORBELL, DBELL_UP_ARM); - } - - if ((status & DBELL_DOWN_HOST) != 0) { - card->csr &= ~DBELL_DOWN_ARM; - c4_dispatch_tx(card); - } else if (card->csr & DBELL_DOWN_HOST) { - if (c4inmeml(card->mbase + MBOX_DOWN_LEN) == 0) { - card->csr &= ~DBELL_DOWN_ARM; - c4_dispatch_tx(card); - } - } - spin_unlock_irqrestore(&card->lock, flags); - return IRQ_HANDLED; -} - -static irqreturn_t c4_interrupt(int interrupt, void *devptr) -{ - avmcard *card = devptr; - - return c4_handle_interrupt(card); -} - -/* ------------------------------------------------------------- */ - -static void c4_send_init(avmcard *card) -{ - struct sk_buff *skb; - void *p; - unsigned long flags; - - skb = alloc_skb(15, GFP_ATOMIC); - if (!skb) { - printk(KERN_CRIT "%s: no memory, lost register appl.\n", - card->name); - return; - } - p = skb->data; - _put_byte(&p, 0); - _put_byte(&p, 0); - _put_byte(&p, SEND_INIT); - _put_word(&p, CAPI_MAXAPPL); - _put_word(&p, AVM_NCCI_PER_CHANNEL * 30); - _put_word(&p, card->cardnr - 1); - skb_put(skb, (u8 *)p - (u8 *)skb->data); - - skb_queue_tail(&card->dma->send_queue, skb); - spin_lock_irqsave(&card->lock, flags); - c4_dispatch_tx(card); - spin_unlock_irqrestore(&card->lock, flags); -} - -static int queue_sendconfigword(avmcard *card, u32 val) -{ - struct sk_buff *skb; - unsigned long flags; - void *p; - - skb = alloc_skb(3 + 4, GFP_ATOMIC); - if (!skb) { - printk(KERN_CRIT "%s: no memory, send config\n", - card->name); - return -ENOMEM; - } - p = skb->data; - _put_byte(&p, 0); - _put_byte(&p, 0); - _put_byte(&p, SEND_CONFIG); - _put_word(&p, val); - skb_put(skb, (u8 *)p - (u8 *)skb->data); - - skb_queue_tail(&card->dma->send_queue, skb); - spin_lock_irqsave(&card->lock, flags); - c4_dispatch_tx(card); - spin_unlock_irqrestore(&card->lock, flags); - return 0; -} - -static int queue_sendconfig(avmcard *card, char cval[4]) -{ - struct sk_buff *skb; - unsigned long flags; - void *p; - - skb = alloc_skb(3 + 4, GFP_ATOMIC); - if (!skb) { - printk(KERN_CRIT "%s: no memory, send config\n", - card->name); - return -ENOMEM; - } - p = skb->data; - _put_byte(&p, 0); - _put_byte(&p, 0); - _put_byte(&p, SEND_CONFIG); - _put_byte(&p, cval[0]); - _put_byte(&p, cval[1]); - _put_byte(&p, cval[2]); - _put_byte(&p, cval[3]); - skb_put(skb, (u8 *)p - (u8 *)skb->data); - - skb_queue_tail(&card->dma->send_queue, skb); - - spin_lock_irqsave(&card->lock, flags); - c4_dispatch_tx(card); - spin_unlock_irqrestore(&card->lock, flags); - return 0; -} - -static int c4_send_config(avmcard *card, capiloaddatapart *config) -{ - u8 val[4]; - unsigned char *dp; - u_int left; - int retval; - - if ((retval = queue_sendconfigword(card, 1)) != 0) - return retval; - if ((retval = queue_sendconfigword(card, config->len)) != 0) - return retval; - - dp = config->data; - left = config->len; - while (left >= sizeof(u32)) { - if (config->user) { - if (copy_from_user(val, dp, sizeof(val))) - return -EFAULT; - } else { - memcpy(val, dp, sizeof(val)); - } - if ((retval = queue_sendconfig(card, val)) != 0) - return retval; - left -= sizeof(val); - dp += sizeof(val); - } - if (left) { - memset(val, 0, sizeof(val)); - if (config->user) { - if (copy_from_user(&val, dp, left)) - return -EFAULT; - } else { - memcpy(&val, dp, left); - } - if ((retval = queue_sendconfig(card, val)) != 0) - return retval; - } - - return 0; -} - -static int c4_load_firmware(struct capi_ctr *ctrl, capiloaddata *data) -{ - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - avmcard *card = cinfo->card; - int retval; - - if ((retval = c4_load_t4file(card, &data->firmware))) { - printk(KERN_ERR "%s: failed to load t4file!!\n", - card->name); - c4_reset(card); - return retval; - } - - card->csr = 0; - c4outmeml(card->mbase + MBOX_UP_LEN, 0); - c4outmeml(card->mbase + MBOX_DOWN_LEN, 0); - c4outmeml(card->mbase + DOORBELL, DBELL_INIT); - mdelay(1); - c4outmeml(card->mbase + DOORBELL, - DBELL_UP_HOST | DBELL_DOWN_HOST | DBELL_RESET_HOST); - - c4outmeml(card->mbase + PCI_OUT_INT_MASK, 0x08); - - card->dma->recvlen = 0; - c4outmeml(card->mbase + MBOX_UP_ADDR, card->dma->recvbuf.dmaaddr); - c4outmeml(card->mbase + MBOX_UP_LEN, card->dma->recvbuf.size); - c4outmeml(card->mbase + DOORBELL, DBELL_UP_ARM); - - if (data->configuration.len > 0 && data->configuration.data) { - retval = c4_send_config(card, &data->configuration); - if (retval) { - printk(KERN_ERR "%s: failed to set config!!\n", - card->name); - c4_reset(card); - return retval; - } - } - - c4_send_init(card); - - return 0; -} - - -static void c4_reset_ctr(struct capi_ctr *ctrl) -{ - avmcard *card = ((avmctrl_info *)(ctrl->driverdata))->card; - avmctrl_info *cinfo; - u_int i; - unsigned long flags; - - spin_lock_irqsave(&card->lock, flags); - - c4_reset(card); - - spin_unlock_irqrestore(&card->lock, flags); - - for (i = 0; i < card->nr_controllers; i++) { - cinfo = &card->ctrlinfo[i]; - memset(cinfo->version, 0, sizeof(cinfo->version)); - capi_ctr_down(&cinfo->capi_ctrl); - } - card->nlogcontr = 0; -} - -static void c4_remove(struct pci_dev *pdev) -{ - avmcard *card = pci_get_drvdata(pdev); - avmctrl_info *cinfo; - u_int i; - - if (!card) - return; - - c4_reset(card); - - for (i = 0; i < card->nr_controllers; i++) { - cinfo = &card->ctrlinfo[i]; - detach_capi_ctr(&cinfo->capi_ctrl); - } - - free_irq(card->irq, card); - iounmap(card->mbase); - release_region(card->port, AVMB1_PORTLEN); - avmcard_dma_free(card->dma); - pci_set_drvdata(pdev, NULL); - b1_free_card(card); -} - -/* ------------------------------------------------------------- */ - - -static void c4_register_appl(struct capi_ctr *ctrl, - u16 appl, - capi_register_params *rp) -{ - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - avmcard *card = cinfo->card; - struct sk_buff *skb; - int want = rp->level3cnt; - unsigned long flags; - int nconn; - void *p; - - if (ctrl->cnr == card->cardnr) { - - if (want > 0) nconn = want; - else nconn = ctrl->profile.nbchannel * 4 * -want; - if (nconn == 0) nconn = ctrl->profile.nbchannel * 4; - - skb = alloc_skb(23, GFP_ATOMIC); - if (!skb) { - printk(KERN_CRIT "%s: no memory, lost register appl.\n", - card->name); - return; - } - p = skb->data; - _put_byte(&p, 0); - _put_byte(&p, 0); - _put_byte(&p, SEND_REGISTER); - _put_word(&p, appl); - _put_word(&p, 1024 * (nconn + 1)); - _put_word(&p, nconn); - _put_word(&p, rp->datablkcnt); - _put_word(&p, rp->datablklen); - skb_put(skb, (u8 *)p - (u8 *)skb->data); - - skb_queue_tail(&card->dma->send_queue, skb); - - spin_lock_irqsave(&card->lock, flags); - c4_dispatch_tx(card); - spin_unlock_irqrestore(&card->lock, flags); - } -} - -/* ------------------------------------------------------------- */ - -static void c4_release_appl(struct capi_ctr *ctrl, u16 appl) -{ - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - avmcard *card = cinfo->card; - unsigned long flags; - struct sk_buff *skb; - void *p; - - spin_lock_irqsave(&card->lock, flags); - capilib_release_appl(&cinfo->ncci_head, appl); - spin_unlock_irqrestore(&card->lock, flags); - - if (ctrl->cnr == card->cardnr) { - skb = alloc_skb(7, GFP_ATOMIC); - if (!skb) { - printk(KERN_CRIT "%s: no memory, lost release appl.\n", - card->name); - return; - } - p = skb->data; - _put_byte(&p, 0); - _put_byte(&p, 0); - _put_byte(&p, SEND_RELEASE); - _put_word(&p, appl); - - skb_put(skb, (u8 *)p - (u8 *)skb->data); - skb_queue_tail(&card->dma->send_queue, skb); - spin_lock_irqsave(&card->lock, flags); - c4_dispatch_tx(card); - spin_unlock_irqrestore(&card->lock, flags); - } -} - -/* ------------------------------------------------------------- */ - - -static u16 c4_send_message(struct capi_ctr *ctrl, struct sk_buff *skb) -{ - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - avmcard *card = cinfo->card; - u16 retval = CAPI_NOERROR; - unsigned long flags; - - spin_lock_irqsave(&card->lock, flags); - if (CAPIMSG_CMD(skb->data) == CAPI_DATA_B3_REQ) { - retval = capilib_data_b3_req(&cinfo->ncci_head, - CAPIMSG_APPID(skb->data), - CAPIMSG_NCCI(skb->data), - CAPIMSG_MSGID(skb->data)); - } - if (retval == CAPI_NOERROR) { - skb_queue_tail(&card->dma->send_queue, skb); - c4_dispatch_tx(card); - } - spin_unlock_irqrestore(&card->lock, flags); - return retval; -} - -/* ------------------------------------------------------------- */ - -static char *c4_procinfo(struct capi_ctr *ctrl) -{ - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - - if (!cinfo) - return ""; - sprintf(cinfo->infobuf, "%s %s 0x%x %d 0x%lx", - cinfo->cardname[0] ? cinfo->cardname : "-", - cinfo->version[VER_DRIVER] ? cinfo->version[VER_DRIVER] : "-", - cinfo->card ? cinfo->card->port : 0x0, - cinfo->card ? cinfo->card->irq : 0, - cinfo->card ? cinfo->card->membase : 0 - ); - return cinfo->infobuf; -} - -static int c4_proc_show(struct seq_file *m, void *v) -{ - struct capi_ctr *ctrl = m->private; - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - avmcard *card = cinfo->card; - u8 flag; - char *s; - - seq_printf(m, "%-16s %s\n", "name", card->name); - seq_printf(m, "%-16s 0x%x\n", "io", card->port); - seq_printf(m, "%-16s %d\n", "irq", card->irq); - seq_printf(m, "%-16s 0x%lx\n", "membase", card->membase); - switch (card->cardtype) { - case avm_b1isa: s = "B1 ISA"; break; - case avm_b1pci: s = "B1 PCI"; break; - case avm_b1pcmcia: s = "B1 PCMCIA"; break; - case avm_m1: s = "M1"; break; - case avm_m2: s = "M2"; break; - case avm_t1isa: s = "T1 ISA (HEMA)"; break; - case avm_t1pci: s = "T1 PCI"; break; - case avm_c4: s = "C4"; break; - case avm_c2: s = "C2"; break; - default: s = "???"; break; - } - seq_printf(m, "%-16s %s\n", "type", s); - if ((s = cinfo->version[VER_DRIVER]) != NULL) - seq_printf(m, "%-16s %s\n", "ver_driver", s); - if ((s = cinfo->version[VER_CARDTYPE]) != NULL) - seq_printf(m, "%-16s %s\n", "ver_cardtype", s); - if ((s = cinfo->version[VER_SERIAL]) != NULL) - seq_printf(m, "%-16s %s\n", "ver_serial", s); - - if (card->cardtype != avm_m1) { - flag = ((u8 *)(ctrl->profile.manu))[3]; - if (flag) - seq_printf(m, "%-16s%s%s%s%s%s%s%s\n", - "protocol", - (flag & 0x01) ? " DSS1" : "", - (flag & 0x02) ? " CT1" : "", - (flag & 0x04) ? " VN3" : "", - (flag & 0x08) ? " NI1" : "", - (flag & 0x10) ? " AUSTEL" : "", - (flag & 0x20) ? " ESS" : "", - (flag & 0x40) ? " 1TR6" : "" - ); - } - if (card->cardtype != avm_m1) { - flag = ((u8 *)(ctrl->profile.manu))[5]; - if (flag) - seq_printf(m, "%-16s%s%s%s%s\n", - "linetype", - (flag & 0x01) ? " point to point" : "", - (flag & 0x02) ? " point to multipoint" : "", - (flag & 0x08) ? " leased line without D-channel" : "", - (flag & 0x04) ? " leased line with D-channel" : "" - ); - } - seq_printf(m, "%-16s %s\n", "cardname", cinfo->cardname); - - return 0; -} - -/* ------------------------------------------------------------- */ - -static int c4_add_card(struct capicardparams *p, struct pci_dev *dev, - int nr_controllers) -{ - avmcard *card; - avmctrl_info *cinfo; - int retval; - int i; - - card = b1_alloc_card(nr_controllers); - if (!card) { - printk(KERN_WARNING "c4: no memory.\n"); - retval = -ENOMEM; - goto err; - } - card->dma = avmcard_dma_alloc("c4", dev, 2048 + 128, 2048 + 128); - if (!card->dma) { - printk(KERN_WARNING "c4: no memory.\n"); - retval = -ENOMEM; - goto err_free; - } - - sprintf(card->name, "c%d-%x", nr_controllers, p->port); - card->port = p->port; - card->irq = p->irq; - card->membase = p->membase; - card->cardtype = (nr_controllers == 4) ? avm_c4 : avm_c2; - - if (!request_region(card->port, AVMB1_PORTLEN, card->name)) { - printk(KERN_WARNING "c4: ports 0x%03x-0x%03x in use.\n", - card->port, card->port + AVMB1_PORTLEN); - retval = -EBUSY; - goto err_free_dma; - } - - card->mbase = ioremap(card->membase, 128); - if (card->mbase == NULL) { - printk(KERN_NOTICE "c4: can't remap memory at 0x%lx\n", - card->membase); - retval = -EIO; - goto err_release_region; - } - - retval = c4_detect(card); - if (retval != 0) { - printk(KERN_NOTICE "c4: NO card at 0x%x error(%d)\n", - card->port, retval); - retval = -EIO; - goto err_unmap; - } - c4_reset(card); - - retval = request_irq(card->irq, c4_interrupt, IRQF_SHARED, card->name, card); - if (retval) { - printk(KERN_ERR "c4: unable to get IRQ %d.\n", card->irq); - retval = -EBUSY; - goto err_unmap; - } - - for (i = 0; i < nr_controllers; i++) { - cinfo = &card->ctrlinfo[i]; - cinfo->capi_ctrl.owner = THIS_MODULE; - cinfo->capi_ctrl.driver_name = "c4"; - cinfo->capi_ctrl.driverdata = cinfo; - cinfo->capi_ctrl.register_appl = c4_register_appl; - cinfo->capi_ctrl.release_appl = c4_release_appl; - cinfo->capi_ctrl.send_message = c4_send_message; - cinfo->capi_ctrl.load_firmware = c4_load_firmware; - cinfo->capi_ctrl.reset_ctr = c4_reset_ctr; - cinfo->capi_ctrl.procinfo = c4_procinfo; - cinfo->capi_ctrl.proc_show = c4_proc_show; - strcpy(cinfo->capi_ctrl.name, card->name); - - retval = attach_capi_ctr(&cinfo->capi_ctrl); - if (retval) { - printk(KERN_ERR "c4: attach controller failed (%d).\n", i); - for (i--; i >= 0; i--) { - cinfo = &card->ctrlinfo[i]; - detach_capi_ctr(&cinfo->capi_ctrl); - } - goto err_free_irq; - } - if (i == 0) - card->cardnr = cinfo->capi_ctrl.cnr; - } - - printk(KERN_INFO "c4: AVM C%d at i/o %#x, irq %d, mem %#lx\n", - nr_controllers, card->port, card->irq, - card->membase); - pci_set_drvdata(dev, card); - return 0; - -err_free_irq: - free_irq(card->irq, card); -err_unmap: - iounmap(card->mbase); -err_release_region: - release_region(card->port, AVMB1_PORTLEN); -err_free_dma: - avmcard_dma_free(card->dma); -err_free: - b1_free_card(card); -err: - return retval; -} - -/* ------------------------------------------------------------- */ - -static int c4_probe(struct pci_dev *dev, const struct pci_device_id *ent) -{ - int nr = ent->driver_data; - int retval = 0; - struct capicardparams param; - - if (pci_enable_device(dev) < 0) { - printk(KERN_ERR "c4: failed to enable AVM-C%d\n", nr); - return -ENODEV; - } - pci_set_master(dev); - - param.port = pci_resource_start(dev, 1); - param.irq = dev->irq; - param.membase = pci_resource_start(dev, 0); - - printk(KERN_INFO "c4: PCI BIOS reports AVM-C%d at i/o %#x, irq %d, mem %#x\n", - nr, param.port, param.irq, param.membase); - - retval = c4_add_card(¶m, dev, nr); - if (retval != 0) { - printk(KERN_ERR "c4: no AVM-C%d at i/o %#x, irq %d detected, mem %#x\n", - nr, param.port, param.irq, param.membase); - pci_disable_device(dev); - return -ENODEV; - } - return 0; -} - -static struct pci_driver c4_pci_driver = { - .name = "c4", - .id_table = c4_pci_tbl, - .probe = c4_probe, - .remove = c4_remove, -}; - -static struct capi_driver capi_driver_c2 = { - .name = "c2", - .revision = "1.0", -}; - -static struct capi_driver capi_driver_c4 = { - .name = "c4", - .revision = "1.0", -}; - -static int __init c4_init(void) -{ - char *p; - char rev[32]; - int err; - - if ((p = strchr(revision, ':')) != NULL && p[1]) { - strlcpy(rev, p + 2, 32); - if ((p = strchr(rev, '$')) != NULL && p > rev) - *(p - 1) = 0; - } else - strcpy(rev, "1.0"); - - err = pci_register_driver(&c4_pci_driver); - if (!err) { - strlcpy(capi_driver_c2.revision, rev, 32); - register_capi_driver(&capi_driver_c2); - strlcpy(capi_driver_c4.revision, rev, 32); - register_capi_driver(&capi_driver_c4); - printk(KERN_INFO "c4: revision %s\n", rev); - } - return err; -} - -static void __exit c4_exit(void) -{ - unregister_capi_driver(&capi_driver_c2); - unregister_capi_driver(&capi_driver_c4); - pci_unregister_driver(&c4_pci_driver); -} - -module_init(c4_init); -module_exit(c4_exit); diff --git a/drivers/staging/isdn/avm/t1isa.c b/drivers/staging/isdn/avm/t1isa.c deleted file mode 100644 index 2153619c5b31..000000000000 --- a/drivers/staging/isdn/avm/t1isa.c +++ /dev/null @@ -1,594 +0,0 @@ -/* $Id: t1isa.c,v 1.1.2.3 2004/02/10 01:07:12 keil Exp $ - * - * Module for AVM T1 HEMA-card. - * - * Copyright 1999 by Carsten Paeth <calle@calle.de> - * - * This software may be used and distributed according to the terms - * of the GNU General Public License, incorporated herein by reference. - * - */ - -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/skbuff.h> -#include <linux/delay.h> -#include <linux/mm.h> -#include <linux/interrupt.h> -#include <linux/ioport.h> -#include <linux/capi.h> -#include <linux/netdevice.h> -#include <linux/kernelcapi.h> -#include <linux/init.h> -#include <linux/pci.h> -#include <linux/gfp.h> -#include <asm/io.h> -#include <linux/isdn/capicmd.h> -#include <linux/isdn/capiutil.h> -#include <linux/isdn/capilli.h> -#include "avmcard.h" - -/* ------------------------------------------------------------- */ - -static char *revision = "$Revision: 1.1.2.3 $"; - -/* ------------------------------------------------------------- */ - -MODULE_DESCRIPTION("CAPI4Linux: Driver for AVM T1 HEMA ISA card"); -MODULE_AUTHOR("Carsten Paeth"); -MODULE_LICENSE("GPL"); - -/* ------------------------------------------------------------- */ - -static int hema_irq_table[16] = -{0, - 0, - 0, - 0x80, /* irq 3 */ - 0, - 0x90, /* irq 5 */ - 0, - 0xA0, /* irq 7 */ - 0, - 0xB0, /* irq 9 */ - 0xC0, /* irq 10 */ - 0xD0, /* irq 11 */ - 0xE0, /* irq 12 */ - 0, - 0, - 0xF0, /* irq 15 */ -}; - -static int t1_detectandinit(unsigned int base, unsigned irq, int cardnr) -{ - unsigned char cregs[8]; - unsigned char reverse_cardnr; - unsigned char dummy; - int i; - - reverse_cardnr = ((cardnr & 0x01) << 3) | ((cardnr & 0x02) << 1) - | ((cardnr & 0x04) >> 1) | ((cardnr & 0x08) >> 3); - cregs[0] = (HEMA_VERSION_ID << 4) | (reverse_cardnr & 0xf); - cregs[1] = 0x00; /* fast & slow link connected to CON1 */ - cregs[2] = 0x05; /* fast link 20MBit, slow link 20 MBit */ - cregs[3] = 0; - cregs[4] = 0x11; /* zero wait state */ - cregs[5] = hema_irq_table[irq & 0xf]; - cregs[6] = 0; - cregs[7] = 0; - - /* - * no one else should use the ISA bus in this moment, - * but no function there to prevent this :-( - * save_flags(flags); cli(); - */ - - /* board reset */ - t1outp(base, T1_RESETBOARD, 0xf); - mdelay(100); - dummy = t1inp(base, T1_FASTLINK + T1_OUTSTAT); /* first read */ - - /* write config */ - dummy = (base >> 4) & 0xff; - for (i = 1; i <= 0xf; i++) t1outp(base, i, dummy); - t1outp(base, HEMA_PAL_ID & 0xf, dummy); - t1outp(base, HEMA_PAL_ID >> 4, cregs[0]); - for (i = 1; i < 7; i++) t1outp(base, 0, cregs[i]); - t1outp(base, ((base >> 4)) & 0x3, cregs[7]); - /* restore_flags(flags); */ - - mdelay(100); - t1outp(base, T1_FASTLINK + T1_RESETLINK, 0); - t1outp(base, T1_SLOWLINK + T1_RESETLINK, 0); - mdelay(10); - t1outp(base, T1_FASTLINK + T1_RESETLINK, 1); - t1outp(base, T1_SLOWLINK + T1_RESETLINK, 1); - mdelay(100); - t1outp(base, T1_FASTLINK + T1_RESETLINK, 0); - t1outp(base, T1_SLOWLINK + T1_RESETLINK, 0); - mdelay(10); - t1outp(base, T1_FASTLINK + T1_ANALYSE, 0); - mdelay(5); - t1outp(base, T1_SLOWLINK + T1_ANALYSE, 0); - - if (t1inp(base, T1_FASTLINK + T1_OUTSTAT) != 0x1) /* tx empty */ - return 1; - if (t1inp(base, T1_FASTLINK + T1_INSTAT) != 0x0) /* rx empty */ - return 2; - if (t1inp(base, T1_FASTLINK + T1_IRQENABLE) != 0x0) - return 3; - if ((t1inp(base, T1_FASTLINK + T1_FIFOSTAT) & 0xf0) != 0x70) - return 4; - if ((t1inp(base, T1_FASTLINK + T1_IRQMASTER) & 0x0e) != 0) - return 5; - if ((t1inp(base, T1_FASTLINK + T1_IDENT) & 0x7d) != 1) - return 6; - if (t1inp(base, T1_SLOWLINK + T1_OUTSTAT) != 0x1) /* tx empty */ - return 7; - if ((t1inp(base, T1_SLOWLINK + T1_IRQMASTER) & 0x0e) != 0) - return 8; - if ((t1inp(base, T1_SLOWLINK + T1_IDENT) & 0x7d) != 0) - return 9; - return 0; -} - -static irqreturn_t t1isa_interrupt(int interrupt, void *devptr) -{ - avmcard *card = devptr; - avmctrl_info *cinfo = &card->ctrlinfo[0]; - struct capi_ctr *ctrl = &cinfo->capi_ctrl; - unsigned char b1cmd; - struct sk_buff *skb; - - unsigned ApplId; - unsigned MsgLen; - unsigned DataB3Len; - unsigned NCCI; - unsigned WindowSize; - unsigned long flags; - - spin_lock_irqsave(&card->lock, flags); - - while (b1_rx_full(card->port)) { - - b1cmd = b1_get_byte(card->port); - - switch (b1cmd) { - - case RECEIVE_DATA_B3_IND: - - ApplId = (unsigned) b1_get_word(card->port); - MsgLen = t1_get_slice(card->port, card->msgbuf); - DataB3Len = t1_get_slice(card->port, card->databuf); - spin_unlock_irqrestore(&card->lock, flags); - - if (MsgLen < 30) { /* not CAPI 64Bit */ - memset(card->msgbuf + MsgLen, 0, 30 - MsgLen); - MsgLen = 30; - CAPIMSG_SETLEN(card->msgbuf, 30); - } - if (!(skb = alloc_skb(DataB3Len + MsgLen, GFP_ATOMIC))) { - printk(KERN_ERR "%s: incoming packet dropped\n", - card->name); - } else { - skb_put_data(skb, card->msgbuf, MsgLen); - skb_put_data(skb, card->databuf, DataB3Len); - capi_ctr_handle_message(ctrl, ApplId, skb); - } - break; - - case RECEIVE_MESSAGE: - - ApplId = (unsigned) b1_get_word(card->port); - MsgLen = t1_get_slice(card->port, card->msgbuf); - if (!(skb = alloc_skb(MsgLen, GFP_ATOMIC))) { - spin_unlock_irqrestore(&card->lock, flags); - printk(KERN_ERR "%s: incoming packet dropped\n", - card->name); - } else { - skb_put_data(skb, card->msgbuf, MsgLen); - if (CAPIMSG_CMD(skb->data) == CAPI_DATA_B3) - capilib_data_b3_conf(&cinfo->ncci_head, ApplId, - CAPIMSG_NCCI(skb->data), - CAPIMSG_MSGID(skb->data)); - spin_unlock_irqrestore(&card->lock, flags); - capi_ctr_handle_message(ctrl, ApplId, skb); - } - break; - - case RECEIVE_NEW_NCCI: - - ApplId = b1_get_word(card->port); - NCCI = b1_get_word(card->port); - WindowSize = b1_get_word(card->port); - capilib_new_ncci(&cinfo->ncci_head, ApplId, NCCI, WindowSize); - spin_unlock_irqrestore(&card->lock, flags); - break; - - case RECEIVE_FREE_NCCI: - - ApplId = b1_get_word(card->port); - NCCI = b1_get_word(card->port); - if (NCCI != 0xffffffff) - capilib_free_ncci(&cinfo->ncci_head, ApplId, NCCI); - spin_unlock_irqrestore(&card->lock, flags); - break; - - case RECEIVE_START: - b1_put_byte(card->port, SEND_POLLACK); - spin_unlock_irqrestore(&card->lock, flags); - capi_ctr_resume_output(ctrl); - break; - - case RECEIVE_STOP: - spin_unlock_irqrestore(&card->lock, flags); - capi_ctr_suspend_output(ctrl); - break; - - case RECEIVE_INIT: - - cinfo->versionlen = t1_get_slice(card->port, cinfo->versionbuf); - spin_unlock_irqrestore(&card->lock, flags); - b1_parse_version(cinfo); - printk(KERN_INFO "%s: %s-card (%s) now active\n", - card->name, - cinfo->version[VER_CARDTYPE], - cinfo->version[VER_DRIVER]); - capi_ctr_ready(ctrl); - break; - - case RECEIVE_TASK_READY: - ApplId = (unsigned) b1_get_word(card->port); - MsgLen = t1_get_slice(card->port, card->msgbuf); - spin_unlock_irqrestore(&card->lock, flags); - card->msgbuf[MsgLen] = 0; - while (MsgLen > 0 - && (card->msgbuf[MsgLen - 1] == '\n' - || card->msgbuf[MsgLen - 1] == '\r')) { - card->msgbuf[MsgLen - 1] = 0; - MsgLen--; - } - printk(KERN_INFO "%s: task %d \"%s\" ready.\n", - card->name, ApplId, card->msgbuf); - break; - - case RECEIVE_DEBUGMSG: - MsgLen = t1_get_slice(card->port, card->msgbuf); - spin_unlock_irqrestore(&card->lock, flags); - card->msgbuf[MsgLen] = 0; - while (MsgLen > 0 - && (card->msgbuf[MsgLen - 1] == '\n' - || card->msgbuf[MsgLen - 1] == '\r')) { - card->msgbuf[MsgLen - 1] = 0; - MsgLen--; - } - printk(KERN_INFO "%s: DEBUG: %s\n", card->name, card->msgbuf); - break; - - - case 0xff: - spin_unlock_irqrestore(&card->lock, flags); - printk(KERN_ERR "%s: card reseted ?\n", card->name); - return IRQ_HANDLED; - default: - spin_unlock_irqrestore(&card->lock, flags); - printk(KERN_ERR "%s: b1_interrupt: 0x%x ???\n", - card->name, b1cmd); - return IRQ_NONE; - } - } - return IRQ_HANDLED; -} - -/* ------------------------------------------------------------- */ - -static int t1isa_load_firmware(struct capi_ctr *ctrl, capiloaddata *data) -{ - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - avmcard *card = cinfo->card; - unsigned int port = card->port; - unsigned long flags; - int retval; - - t1_disable_irq(port); - b1_reset(port); - - if ((retval = b1_load_t4file(card, &data->firmware))) { - b1_reset(port); - printk(KERN_ERR "%s: failed to load t4file!!\n", - card->name); - return retval; - } - - if (data->configuration.len > 0 && data->configuration.data) { - if ((retval = b1_load_config(card, &data->configuration))) { - b1_reset(port); - printk(KERN_ERR "%s: failed to load config!!\n", - card->name); - return retval; - } - } - - if (!b1_loaded(card)) { - printk(KERN_ERR "%s: failed to load t4file.\n", card->name); - return -EIO; - } - - spin_lock_irqsave(&card->lock, flags); - b1_setinterrupt(port, card->irq, card->cardtype); - b1_put_byte(port, SEND_INIT); - b1_put_word(port, CAPI_MAXAPPL); - b1_put_word(port, AVM_NCCI_PER_CHANNEL * 30); - b1_put_word(port, ctrl->cnr - 1); - spin_unlock_irqrestore(&card->lock, flags); - - return 0; -} - -static void t1isa_reset_ctr(struct capi_ctr *ctrl) -{ - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - avmcard *card = cinfo->card; - unsigned int port = card->port; - unsigned long flags; - - t1_disable_irq(port); - b1_reset(port); - b1_reset(port); - - memset(cinfo->version, 0, sizeof(cinfo->version)); - spin_lock_irqsave(&card->lock, flags); - capilib_release(&cinfo->ncci_head); - spin_unlock_irqrestore(&card->lock, flags); - capi_ctr_down(ctrl); -} - -static void t1isa_remove(struct pci_dev *pdev) -{ - avmctrl_info *cinfo = pci_get_drvdata(pdev); - avmcard *card; - - if (!cinfo) - return; - - card = cinfo->card; - - t1_disable_irq(card->port); - b1_reset(card->port); - b1_reset(card->port); - t1_reset(card->port); - - detach_capi_ctr(&cinfo->capi_ctrl); - free_irq(card->irq, card); - release_region(card->port, AVMB1_PORTLEN); - b1_free_card(card); -} - -/* ------------------------------------------------------------- */ - -static u16 t1isa_send_message(struct capi_ctr *ctrl, struct sk_buff *skb); -static char *t1isa_procinfo(struct capi_ctr *ctrl); - -static int t1isa_probe(struct pci_dev *pdev, int cardnr) -{ - avmctrl_info *cinfo; - avmcard *card; - int retval; - - card = b1_alloc_card(1); - if (!card) { - printk(KERN_WARNING "t1isa: no memory.\n"); - retval = -ENOMEM; - goto err; - } - - cinfo = card->ctrlinfo; - card->port = pci_resource_start(pdev, 0); - card->irq = pdev->irq; - card->cardtype = avm_t1isa; - card->cardnr = cardnr; - sprintf(card->name, "t1isa-%x", card->port); - - if (!(((card->port & 0x7) == 0) && ((card->port & 0x30) != 0x30))) { - printk(KERN_WARNING "t1isa: invalid port 0x%x.\n", card->port); - retval = -EINVAL; - goto err_free; - } - if (hema_irq_table[card->irq & 0xf] == 0) { - printk(KERN_WARNING "t1isa: irq %d not valid.\n", card->irq); - retval = -EINVAL; - goto err_free; - } - if (!request_region(card->port, AVMB1_PORTLEN, card->name)) { - printk(KERN_INFO "t1isa: ports 0x%03x-0x%03x in use.\n", - card->port, card->port + AVMB1_PORTLEN); - retval = -EBUSY; - goto err_free; - } - retval = request_irq(card->irq, t1isa_interrupt, 0, card->name, card); - if (retval) { - printk(KERN_INFO "t1isa: unable to get IRQ %d.\n", card->irq); - retval = -EBUSY; - goto err_release_region; - } - - if ((retval = t1_detectandinit(card->port, card->irq, card->cardnr)) != 0) { - printk(KERN_INFO "t1isa: NO card at 0x%x (%d)\n", - card->port, retval); - retval = -ENODEV; - goto err_free_irq; - } - t1_disable_irq(card->port); - b1_reset(card->port); - - cinfo->capi_ctrl.owner = THIS_MODULE; - cinfo->capi_ctrl.driver_name = "t1isa"; - cinfo->capi_ctrl.driverdata = cinfo; - cinfo->capi_ctrl.register_appl = b1_register_appl; - cinfo->capi_ctrl.release_appl = b1_release_appl; - cinfo->capi_ctrl.send_message = t1isa_send_message; - cinfo->capi_ctrl.load_firmware = t1isa_load_firmware; - cinfo->capi_ctrl.reset_ctr = t1isa_reset_ctr; - cinfo->capi_ctrl.procinfo = t1isa_procinfo; - cinfo->capi_ctrl.proc_show = b1_proc_show; - strcpy(cinfo->capi_ctrl.name, card->name); - - retval = attach_capi_ctr(&cinfo->capi_ctrl); - if (retval) { - printk(KERN_INFO "t1isa: attach controller failed.\n"); - goto err_free_irq; - } - - printk(KERN_INFO "t1isa: AVM T1 ISA at i/o %#x, irq %d, card %d\n", - card->port, card->irq, card->cardnr); - - pci_set_drvdata(pdev, cinfo); - return 0; - -err_free_irq: - free_irq(card->irq, card); -err_release_region: - release_region(card->port, AVMB1_PORTLEN); -err_free: - b1_free_card(card); -err: - return retval; -} - -static u16 t1isa_send_message(struct capi_ctr *ctrl, struct sk_buff *skb) -{ - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - avmcard *card = cinfo->card; - unsigned int port = card->port; - unsigned long flags; - u16 len = CAPIMSG_LEN(skb->data); - u8 cmd = CAPIMSG_COMMAND(skb->data); - u8 subcmd = CAPIMSG_SUBCOMMAND(skb->data); - u16 dlen, retval; - - spin_lock_irqsave(&card->lock, flags); - if (CAPICMD(cmd, subcmd) == CAPI_DATA_B3_REQ) { - retval = capilib_data_b3_req(&cinfo->ncci_head, - CAPIMSG_APPID(skb->data), - CAPIMSG_NCCI(skb->data), - CAPIMSG_MSGID(skb->data)); - if (retval != CAPI_NOERROR) { - spin_unlock_irqrestore(&card->lock, flags); - return retval; - } - dlen = CAPIMSG_DATALEN(skb->data); - - b1_put_byte(port, SEND_DATA_B3_REQ); - t1_put_slice(port, skb->data, len); - t1_put_slice(port, skb->data + len, dlen); - } else { - b1_put_byte(port, SEND_MESSAGE); - t1_put_slice(port, skb->data, len); - } - spin_unlock_irqrestore(&card->lock, flags); - dev_kfree_skb_any(skb); - return CAPI_NOERROR; -} -/* ------------------------------------------------------------- */ - -static char *t1isa_procinfo(struct capi_ctr *ctrl) -{ - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - - if (!cinfo) - return ""; - sprintf(cinfo->infobuf, "%s %s 0x%x %d %d", - cinfo->cardname[0] ? cinfo->cardname : "-", - cinfo->version[VER_DRIVER] ? cinfo->version[VER_DRIVER] : "-", - cinfo->card ? cinfo->card->port : 0x0, - cinfo->card ? cinfo->card->irq : 0, - cinfo->card ? cinfo->card->cardnr : 0 - ); - return cinfo->infobuf; -} - - -/* ------------------------------------------------------------- */ - -#define MAX_CARDS 4 -static struct pci_dev isa_dev[MAX_CARDS]; -static int io[MAX_CARDS]; -static int irq[MAX_CARDS]; -static int cardnr[MAX_CARDS]; - -module_param_hw_array(io, int, ioport, NULL, 0); -module_param_hw_array(irq, int, irq, NULL, 0); -module_param_array(cardnr, int, NULL, 0); -MODULE_PARM_DESC(io, "I/O base address(es)"); -MODULE_PARM_DESC(irq, "IRQ number(s) (assigned)"); -MODULE_PARM_DESC(cardnr, "Card number(s) (as jumpered)"); - -static int t1isa_add_card(struct capi_driver *driver, capicardparams *data) -{ - int i; - - for (i = 0; i < MAX_CARDS; i++) { - if (isa_dev[i].resource[0].start) - continue; - - isa_dev[i].resource[0].start = data->port; - isa_dev[i].irq = data->irq; - - if (t1isa_probe(&isa_dev[i], data->cardnr) == 0) - return 0; - } - return -ENODEV; -} - -static struct capi_driver capi_driver_t1isa = { - .name = "t1isa", - .revision = "1.0", - .add_card = t1isa_add_card, -}; - -static int __init t1isa_init(void) -{ - char rev[32]; - char *p; - int i; - - if ((p = strchr(revision, ':')) != NULL && p[1]) { - strlcpy(rev, p + 2, 32); - if ((p = strchr(rev, '$')) != NULL && p > rev) - *(p - 1) = 0; - } else - strcpy(rev, "1.0"); - - for (i = 0; i < MAX_CARDS; i++) { - if (!io[i]) - break; - - isa_dev[i].resource[0].start = io[i]; - isa_dev[i].irq = irq[i]; - - if (t1isa_probe(&isa_dev[i], cardnr[i]) != 0) - return -ENODEV; - } - - strlcpy(capi_driver_t1isa.revision, rev, 32); - register_capi_driver(&capi_driver_t1isa); - printk(KERN_INFO "t1isa: revision %s\n", rev); - - return 0; -} - -static void __exit t1isa_exit(void) -{ - int i; - - unregister_capi_driver(&capi_driver_t1isa); - for (i = 0; i < MAX_CARDS; i++) { - if (!io[i]) - break; - - t1isa_remove(&isa_dev[i]); - } -} - -module_init(t1isa_init); -module_exit(t1isa_exit); diff --git a/drivers/staging/isdn/avm/t1pci.c b/drivers/staging/isdn/avm/t1pci.c deleted file mode 100644 index f5ed1d5004c9..000000000000 --- a/drivers/staging/isdn/avm/t1pci.c +++ /dev/null @@ -1,259 +0,0 @@ -/* $Id: t1pci.c,v 1.1.2.2 2004/01/16 21:09:27 keil Exp $ - * - * Module for AVM T1 PCI-card. - * - * Copyright 1999 by Carsten Paeth <calle@calle.de> - * - * This software may be used and distributed according to the terms - * of the GNU General Public License, incorporated herein by reference. - * - */ - -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/skbuff.h> -#include <linux/delay.h> -#include <linux/mm.h> -#include <linux/interrupt.h> -#include <linux/ioport.h> -#include <linux/pci.h> -#include <linux/capi.h> -#include <linux/init.h> -#include <asm/io.h> -#include <linux/isdn/capicmd.h> -#include <linux/isdn/capiutil.h> -#include <linux/isdn/capilli.h> -#include "avmcard.h" - -#undef CONFIG_T1PCI_DEBUG -#undef CONFIG_T1PCI_POLLDEBUG - -/* ------------------------------------------------------------- */ -static char *revision = "$Revision: 1.1.2.2 $"; -/* ------------------------------------------------------------- */ - -static struct pci_device_id t1pci_pci_tbl[] = { - { PCI_VENDOR_ID_AVM, PCI_DEVICE_ID_AVM_T1, PCI_ANY_ID, PCI_ANY_ID }, - { } /* Terminating entry */ -}; - -MODULE_DEVICE_TABLE(pci, t1pci_pci_tbl); -MODULE_DESCRIPTION("CAPI4Linux: Driver for AVM T1 PCI card"); -MODULE_AUTHOR("Carsten Paeth"); -MODULE_LICENSE("GPL"); - -/* ------------------------------------------------------------- */ - -static char *t1pci_procinfo(struct capi_ctr *ctrl); - -static int t1pci_add_card(struct capicardparams *p, struct pci_dev *pdev) -{ - avmcard *card; - avmctrl_info *cinfo; - int retval; - - card = b1_alloc_card(1); - if (!card) { - printk(KERN_WARNING "t1pci: no memory.\n"); - retval = -ENOMEM; - goto err; - } - - card->dma = avmcard_dma_alloc("t1pci", pdev, 2048 + 128, 2048 + 128); - if (!card->dma) { - printk(KERN_WARNING "t1pci: no memory.\n"); - retval = -ENOMEM; - goto err_free; - } - - cinfo = card->ctrlinfo; - sprintf(card->name, "t1pci-%x", p->port); - card->port = p->port; - card->irq = p->irq; - card->membase = p->membase; - card->cardtype = avm_t1pci; - - if (!request_region(card->port, AVMB1_PORTLEN, card->name)) { - printk(KERN_WARNING "t1pci: ports 0x%03x-0x%03x in use.\n", - card->port, card->port + AVMB1_PORTLEN); - retval = -EBUSY; - goto err_free_dma; - } - - card->mbase = ioremap(card->membase, 64); - if (!card->mbase) { - printk(KERN_NOTICE "t1pci: can't remap memory at 0x%lx\n", - card->membase); - retval = -EIO; - goto err_release_region; - } - - b1dma_reset(card); - - retval = t1pci_detect(card); - if (retval != 0) { - if (retval < 6) - printk(KERN_NOTICE "t1pci: NO card at 0x%x (%d)\n", - card->port, retval); - else - printk(KERN_NOTICE "t1pci: card at 0x%x, but cable not connected or T1 has no power (%d)\n", - card->port, retval); - retval = -EIO; - goto err_unmap; - } - b1dma_reset(card); - - retval = request_irq(card->irq, b1dma_interrupt, IRQF_SHARED, card->name, card); - if (retval) { - printk(KERN_ERR "t1pci: unable to get IRQ %d.\n", card->irq); - retval = -EBUSY; - goto err_unmap; - } - - cinfo->capi_ctrl.owner = THIS_MODULE; - cinfo->capi_ctrl.driver_name = "t1pci"; - cinfo->capi_ctrl.driverdata = cinfo; - cinfo->capi_ctrl.register_appl = b1dma_register_appl; - cinfo->capi_ctrl.release_appl = b1dma_release_appl; - cinfo->capi_ctrl.send_message = b1dma_send_message; - cinfo->capi_ctrl.load_firmware = b1dma_load_firmware; - cinfo->capi_ctrl.reset_ctr = b1dma_reset_ctr; - cinfo->capi_ctrl.procinfo = t1pci_procinfo; - cinfo->capi_ctrl.proc_show = b1dma_proc_show; - strcpy(cinfo->capi_ctrl.name, card->name); - - retval = attach_capi_ctr(&cinfo->capi_ctrl); - if (retval) { - printk(KERN_ERR "t1pci: attach controller failed.\n"); - retval = -EBUSY; - goto err_free_irq; - } - card->cardnr = cinfo->capi_ctrl.cnr; - - printk(KERN_INFO "t1pci: AVM T1 PCI at i/o %#x, irq %d, mem %#lx\n", - card->port, card->irq, card->membase); - - pci_set_drvdata(pdev, card); - return 0; - -err_free_irq: - free_irq(card->irq, card); -err_unmap: - iounmap(card->mbase); -err_release_region: - release_region(card->port, AVMB1_PORTLEN); -err_free_dma: - avmcard_dma_free(card->dma); -err_free: - b1_free_card(card); -err: - return retval; -} - -/* ------------------------------------------------------------- */ - -static void t1pci_remove(struct pci_dev *pdev) -{ - avmcard *card = pci_get_drvdata(pdev); - avmctrl_info *cinfo = card->ctrlinfo; - - b1dma_reset(card); - - detach_capi_ctr(&cinfo->capi_ctrl); - free_irq(card->irq, card); - iounmap(card->mbase); - release_region(card->port, AVMB1_PORTLEN); - avmcard_dma_free(card->dma); - b1_free_card(card); -} - -/* ------------------------------------------------------------- */ - -static char *t1pci_procinfo(struct capi_ctr *ctrl) -{ - avmctrl_info *cinfo = (avmctrl_info *)(ctrl->driverdata); - - if (!cinfo) - return ""; - sprintf(cinfo->infobuf, "%s %s 0x%x %d 0x%lx", - cinfo->cardname[0] ? cinfo->cardname : "-", - cinfo->version[VER_DRIVER] ? cinfo->version[VER_DRIVER] : "-", - cinfo->card ? cinfo->card->port : 0x0, - cinfo->card ? cinfo->card->irq : 0, - cinfo->card ? cinfo->card->membase : 0 - ); - return cinfo->infobuf; -} - -/* ------------------------------------------------------------- */ - -static int t1pci_probe(struct pci_dev *dev, const struct pci_device_id *ent) -{ - struct capicardparams param; - int retval; - - if (pci_enable_device(dev) < 0) { - printk(KERN_ERR "t1pci: failed to enable AVM-T1-PCI\n"); - return -ENODEV; - } - pci_set_master(dev); - - param.port = pci_resource_start(dev, 1); - param.irq = dev->irq; - param.membase = pci_resource_start(dev, 0); - - printk(KERN_INFO "t1pci: PCI BIOS reports AVM-T1-PCI at i/o %#x, irq %d, mem %#x\n", - param.port, param.irq, param.membase); - - retval = t1pci_add_card(¶m, dev); - if (retval != 0) { - printk(KERN_ERR "t1pci: no AVM-T1-PCI at i/o %#x, irq %d detected, mem %#x\n", - param.port, param.irq, param.membase); - pci_disable_device(dev); - return -ENODEV; - } - return 0; -} - -static struct pci_driver t1pci_pci_driver = { - .name = "t1pci", - .id_table = t1pci_pci_tbl, - .probe = t1pci_probe, - .remove = t1pci_remove, -}; - -static struct capi_driver capi_driver_t1pci = { - .name = "t1pci", - .revision = "1.0", -}; - -static int __init t1pci_init(void) -{ - char *p; - char rev[32]; - int err; - - if ((p = strchr(revision, ':')) != NULL && p[1]) { - strlcpy(rev, p + 2, 32); - if ((p = strchr(rev, '$')) != NULL && p > rev) - *(p - 1) = 0; - } else - strcpy(rev, "1.0"); - - err = pci_register_driver(&t1pci_pci_driver); - if (!err) { - strlcpy(capi_driver_t1pci.revision, rev, 32); - register_capi_driver(&capi_driver_t1pci); - printk(KERN_INFO "t1pci: revision %s\n", rev); - } - return err; -} - -static void __exit t1pci_exit(void) -{ - unregister_capi_driver(&capi_driver_t1pci); - pci_unregister_driver(&t1pci_pci_driver); -} - -module_init(t1pci_init); -module_exit(t1pci_exit); diff --git a/drivers/staging/isdn/gigaset/Kconfig b/drivers/staging/isdn/gigaset/Kconfig deleted file mode 100644 index c593105b3600..000000000000 --- a/drivers/staging/isdn/gigaset/Kconfig +++ /dev/null @@ -1,62 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0-only -menuconfig ISDN_DRV_GIGASET - tristate "Siemens Gigaset support" - depends on TTY - select CRC_CCITT - select BITREVERSE - help - This driver supports the Siemens Gigaset SX205/255 family of - ISDN DECT bases, including the predecessors Gigaset 3070/3075 - and 4170/4175 and their T-Com versions Sinus 45isdn and Sinus - 721X. - If you have one of these devices, say M here and for at least - one of the connection specific parts that follow. - This will build a module called "gigaset". - Note: If you build your ISDN subsystem (ISDN_CAPI or ISDN_I4L) - as a module, you have to build this driver as a module too, - otherwise the Gigaset device won't show up as an ISDN device. - -if ISDN_DRV_GIGASET - -config GIGASET_CAPI - bool "Gigaset CAPI support" - depends on ISDN_CAPI='y'||(ISDN_CAPI='m'&&ISDN_DRV_GIGASET='m') - default 'y' - help - Build the Gigaset driver as a CAPI 2.0 driver interfacing with - the Kernel CAPI subsystem. To use it with the old ISDN4Linux - subsystem you'll have to enable the capidrv glue driver. - (select ISDN_CAPI_CAPIDRV.) - Say N to build the old native ISDN4Linux variant. - If unsure, say Y. - -config GIGASET_BASE - tristate "Gigaset base station support" - depends on USB - help - Say M here if you want to use the USB interface of the Gigaset - base for connection to your system. - This will build a module called "bas_gigaset". - -config GIGASET_M105 - tristate "Gigaset M105 support" - depends on USB - help - Say M here if you want to connect to the Gigaset base via DECT - using a Gigaset M105 (Sinus 45 Data 2) USB DECT device. - This will build a module called "usb_gigaset". - -config GIGASET_M101 - tristate "Gigaset M101 support" - help - Say M here if you want to connect to the Gigaset base via DECT - using a Gigaset M101 (Sinus 45 Data 1) RS232 DECT device. - This will build a module called "ser_gigaset". - -config GIGASET_DEBUG - bool "Gigaset debugging" - help - This enables debugging code in the Gigaset drivers. - If in doubt, say yes. - -endif # ISDN_DRV_GIGASET diff --git a/drivers/staging/isdn/gigaset/Makefile b/drivers/staging/isdn/gigaset/Makefile deleted file mode 100644 index 9c010891dcd7..000000000000 --- a/drivers/staging/isdn/gigaset/Makefile +++ /dev/null @@ -1,17 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0 -gigaset-y := common.o interface.o proc.o ev-layer.o asyncdata.o - -ifdef CONFIG_GIGASET_CAPI -gigaset-y += capi.o -else -gigaset-y += dummyll.o -endif - -usb_gigaset-y := usb-gigaset.o -ser_gigaset-y := ser-gigaset.o -bas_gigaset-y := bas-gigaset.o isocdata.o - -obj-$(CONFIG_ISDN_DRV_GIGASET) += gigaset.o -obj-$(CONFIG_GIGASET_M105) += usb_gigaset.o -obj-$(CONFIG_GIGASET_BASE) += bas_gigaset.o -obj-$(CONFIG_GIGASET_M101) += ser_gigaset.o diff --git a/drivers/staging/isdn/gigaset/asyncdata.c b/drivers/staging/isdn/gigaset/asyncdata.c deleted file mode 100644 index a34b3c9d8a71..000000000000 --- a/drivers/staging/isdn/gigaset/asyncdata.c +++ /dev/null @@ -1,606 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -/* - * Common data handling layer for ser_gigaset and usb_gigaset - * - * Copyright (c) 2005 by Tilman Schmidt <tilman@imap.cc>, - * Hansjoerg Lipp <hjlipp@web.de>, - * Stefan Eilers. - * - * ===================================================================== - * ===================================================================== - */ - -#include "gigaset.h" -#include <linux/crc-ccitt.h> -#include <linux/bitrev.h> -#include <linux/export.h> - -/* check if byte must be stuffed/escaped - * I'm not sure which data should be encoded. - * Therefore I will go the hard way and encode every value - * less than 0x20, the flag sequence and the control escape char. - */ -static inline int muststuff(unsigned char c) -{ - if (c < PPP_TRANS) return 1; - if (c == PPP_FLAG) return 1; - if (c == PPP_ESCAPE) return 1; - /* other possible candidates: */ - /* 0x91: XON with parity set */ - /* 0x93: XOFF with parity set */ - return 0; -} - -/* == data input =========================================================== */ - -/* process a block of received bytes in command mode - * (mstate != MS_LOCKED && (inputstate & INS_command)) - * Append received bytes to the command response buffer and forward them - * line by line to the response handler. Exit whenever a mode/state change - * might have occurred. - * Note: Received lines may be terminated by CR, LF, or CR LF, which will be - * removed before passing the line to the response handler. - * Return value: - * number of processed bytes - */ -static unsigned cmd_loop(unsigned numbytes, struct inbuf_t *inbuf) -{ - unsigned char *src = inbuf->data + inbuf->head; - struct cardstate *cs = inbuf->cs; - unsigned cbytes = cs->cbytes; - unsigned procbytes = 0; - unsigned char c; - - while (procbytes < numbytes) { - c = *src++; - procbytes++; - - switch (c) { - case '\n': - if (cbytes == 0 && cs->respdata[0] == '\r') { - /* collapse LF with preceding CR */ - cs->respdata[0] = 0; - break; - } - /* fall through */ - case '\r': - /* end of message line, pass to response handler */ - if (cbytes >= MAX_RESP_SIZE) { - dev_warn(cs->dev, "response too large (%d)\n", - cbytes); - cbytes = MAX_RESP_SIZE; - } - cs->cbytes = cbytes; - gigaset_dbg_buffer(DEBUG_TRANSCMD, "received response", - cbytes, cs->respdata); - gigaset_handle_modem_response(cs); - cbytes = 0; - - /* store EOL byte for CRLF collapsing */ - cs->respdata[0] = c; - - /* cs->dle may have changed */ - if (cs->dle && !(inbuf->inputstate & INS_DLE_command)) - inbuf->inputstate &= ~INS_command; - - /* return for reevaluating state */ - goto exit; - - case DLE_FLAG: - if (inbuf->inputstate & INS_DLE_char) { - /* quoted DLE: clear quote flag */ - inbuf->inputstate &= ~INS_DLE_char; - } else if (cs->dle || - (inbuf->inputstate & INS_DLE_command)) { - /* DLE escape, pass up for handling */ - inbuf->inputstate |= INS_DLE_char; - goto exit; - } - /* quoted or not in DLE mode: treat as regular data */ - /* fall through */ - default: - /* append to line buffer if possible */ - if (cbytes < MAX_RESP_SIZE) - cs->respdata[cbytes] = c; - cbytes++; - } - } -exit: - cs->cbytes = cbytes; - return procbytes; -} - -/* process a block of received bytes in lock mode - * All received bytes are passed unmodified to the tty i/f. - * Return value: - * number of processed bytes - */ -static unsigned lock_loop(unsigned numbytes, struct inbuf_t *inbuf) -{ - unsigned char *src = inbuf->data + inbuf->head; - - gigaset_dbg_buffer(DEBUG_LOCKCMD, "received response", numbytes, src); - gigaset_if_receive(inbuf->cs, src, numbytes); - return numbytes; -} - -/* process a block of received bytes in HDLC data mode - * (mstate != MS_LOCKED && !(inputstate & INS_command) && proto2 == L2_HDLC) - * Collect HDLC frames, undoing byte stuffing and watching for DLE escapes. - * When a frame is complete, check the FCS and pass valid frames to the LL. - * If DLE is encountered, return immediately to let the caller handle it. - * Return value: - * number of processed bytes - */ -static unsigned hdlc_loop(unsigned numbytes, struct inbuf_t *inbuf) -{ - struct cardstate *cs = inbuf->cs; - struct bc_state *bcs = cs->bcs; - int inputstate = bcs->inputstate; - __u16 fcs = bcs->rx_fcs; - struct sk_buff *skb = bcs->rx_skb; - unsigned char *src = inbuf->data + inbuf->head; - unsigned procbytes = 0; - unsigned char c; - - if (inputstate & INS_byte_stuff) { - if (!numbytes) - return 0; - inputstate &= ~INS_byte_stuff; - goto byte_stuff; - } - - while (procbytes < numbytes) { - c = *src++; - procbytes++; - if (c == DLE_FLAG) { - if (inputstate & INS_DLE_char) { - /* quoted DLE: clear quote flag */ - inputstate &= ~INS_DLE_char; - } else if (cs->dle || (inputstate & INS_DLE_command)) { - /* DLE escape, pass up for handling */ - inputstate |= INS_DLE_char; - break; - } - } - - if (c == PPP_ESCAPE) { - /* byte stuffing indicator: pull in next byte */ - if (procbytes >= numbytes) { - /* end of buffer, save for later processing */ - inputstate |= INS_byte_stuff; - break; - } -byte_stuff: - c = *src++; - procbytes++; - if (c == DLE_FLAG) { - if (inputstate & INS_DLE_char) { - /* quoted DLE: clear quote flag */ - inputstate &= ~INS_DLE_char; - } else if (cs->dle || - (inputstate & INS_DLE_command)) { - /* DLE escape, pass up for handling */ - inputstate |= - INS_DLE_char | INS_byte_stuff; - break; - } - } - c ^= PPP_TRANS; -#ifdef CONFIG_GIGASET_DEBUG - if (!muststuff(c)) - gig_dbg(DEBUG_HDLC, "byte stuffed: 0x%02x", c); -#endif - } else if (c == PPP_FLAG) { - /* end of frame: process content if any */ - if (inputstate & INS_have_data) { - gig_dbg(DEBUG_HDLC, - "7e----------------------------"); - - /* check and pass received frame */ - if (!skb) { - /* skipped frame */ - gigaset_isdn_rcv_err(bcs); - } else if (skb->len < 2) { - /* frame too short for FCS */ - dev_warn(cs->dev, - "short frame (%d)\n", - skb->len); - gigaset_isdn_rcv_err(bcs); - dev_kfree_skb_any(skb); - } else if (fcs != PPP_GOODFCS) { - /* frame check error */ - dev_err(cs->dev, - "Checksum failed, %u bytes corrupted!\n", - skb->len); - gigaset_isdn_rcv_err(bcs); - dev_kfree_skb_any(skb); - } else { - /* good frame */ - __skb_trim(skb, skb->len - 2); - gigaset_skb_rcvd(bcs, skb); - } - - /* prepare reception of next frame */ - inputstate &= ~INS_have_data; - skb = gigaset_new_rx_skb(bcs); - } else { - /* empty frame (7E 7E) */ -#ifdef CONFIG_GIGASET_DEBUG - ++bcs->emptycount; -#endif - if (!skb) { - /* skipped (?) */ - gigaset_isdn_rcv_err(bcs); - skb = gigaset_new_rx_skb(bcs); - } - } - - fcs = PPP_INITFCS; - continue; -#ifdef CONFIG_GIGASET_DEBUG - } else if (muststuff(c)) { - /* Should not happen. Possible after ZDLE=1<CR><LF>. */ - gig_dbg(DEBUG_HDLC, "not byte stuffed: 0x%02x", c); -#endif - } - - /* regular data byte, append to skb */ -#ifdef CONFIG_GIGASET_DEBUG - if (!(inputstate & INS_have_data)) { - gig_dbg(DEBUG_HDLC, "7e (%d x) ================", - bcs->emptycount); - bcs->emptycount = 0; - } -#endif - inputstate |= INS_have_data; - if (skb) { - if (skb->len >= bcs->rx_bufsize) { - dev_warn(cs->dev, "received packet too long\n"); - dev_kfree_skb_any(skb); - /* skip remainder of packet */ - bcs->rx_skb = skb = NULL; - } else { - __skb_put_u8(skb, c); - fcs = crc_ccitt_byte(fcs, c); - } - } - } - - bcs->inputstate = inputstate; - bcs->rx_fcs = fcs; - return procbytes; -} - -/* process a block of received bytes in transparent data mode - * (mstate != MS_LOCKED && !(inputstate & INS_command) && proto2 != L2_HDLC) - * Invert bytes, undoing byte stuffing and watching for DLE escapes. - * If DLE is encountered, return immediately to let the caller handle it. - * Return value: - * number of processed bytes - */ -static unsigned iraw_loop(unsigned numbytes, struct inbuf_t *inbuf) -{ - struct cardstate *cs = inbuf->cs; - struct bc_state *bcs = cs->bcs; - int inputstate = bcs->inputstate; - struct sk_buff *skb = bcs->rx_skb; - unsigned char *src = inbuf->data + inbuf->head; - unsigned procbytes = 0; - unsigned char c; - - if (!skb) { - /* skip this block */ - gigaset_new_rx_skb(bcs); - return numbytes; - } - - while (procbytes < numbytes && skb->len < bcs->rx_bufsize) { - c = *src++; - procbytes++; - - if (c == DLE_FLAG) { - if (inputstate & INS_DLE_char) { - /* quoted DLE: clear quote flag */ - inputstate &= ~INS_DLE_char; - } else if (cs->dle || (inputstate & INS_DLE_command)) { - /* DLE escape, pass up for handling */ - inputstate |= INS_DLE_char; - break; - } - } - - /* regular data byte: append to current skb */ - inputstate |= INS_have_data; - __skb_put_u8(skb, bitrev8(c)); - } - - /* pass data up */ - if (inputstate & INS_have_data) { - gigaset_skb_rcvd(bcs, skb); - inputstate &= ~INS_have_data; - gigaset_new_rx_skb(bcs); - } - - bcs->inputstate = inputstate; - return procbytes; -} - -/* process DLE escapes - * Called whenever a DLE sequence might be encountered in the input stream. - * Either processes the entire DLE sequence or, if that isn't possible, - * notes the fact that an initial DLE has been received in the INS_DLE_char - * inputstate flag and resumes processing of the sequence on the next call. - */ -static void handle_dle(struct inbuf_t *inbuf) -{ - struct cardstate *cs = inbuf->cs; - - if (cs->mstate == MS_LOCKED) - return; /* no DLE processing in lock mode */ - - if (!(inbuf->inputstate & INS_DLE_char)) { - /* no DLE pending */ - if (inbuf->data[inbuf->head] == DLE_FLAG && - (cs->dle || inbuf->inputstate & INS_DLE_command)) { - /* start of DLE sequence */ - inbuf->head++; - if (inbuf->head == inbuf->tail || - inbuf->head == RBUFSIZE) { - /* end of buffer, save for later processing */ - inbuf->inputstate |= INS_DLE_char; - return; - } - } else { - /* regular data byte */ - return; - } - } - - /* consume pending DLE */ - inbuf->inputstate &= ~INS_DLE_char; - - switch (inbuf->data[inbuf->head]) { - case 'X': /* begin of event message */ - if (inbuf->inputstate & INS_command) - dev_notice(cs->dev, - "received <DLE>X in command mode\n"); - inbuf->inputstate |= INS_command | INS_DLE_command; - inbuf->head++; /* byte consumed */ - break; - case '.': /* end of event message */ - if (!(inbuf->inputstate & INS_DLE_command)) - dev_notice(cs->dev, - "received <DLE>. without <DLE>X\n"); - inbuf->inputstate &= ~INS_DLE_command; - /* return to data mode if in DLE mode */ - if (cs->dle) - inbuf->inputstate &= ~INS_command; - inbuf->head++; /* byte consumed */ - break; - case DLE_FLAG: /* DLE in data stream */ - /* mark as quoted */ - inbuf->inputstate |= INS_DLE_char; - if (!(cs->dle || inbuf->inputstate & INS_DLE_command)) - dev_notice(cs->dev, - "received <DLE><DLE> not in DLE mode\n"); - break; /* quoted byte left in buffer */ - default: - dev_notice(cs->dev, "received <DLE><%02x>\n", - inbuf->data[inbuf->head]); - /* quoted byte left in buffer */ - } -} - -/** - * gigaset_m10x_input() - process a block of data received from the device - * @inbuf: received data and device descriptor structure. - * - * Called by hardware module {ser,usb}_gigaset with a block of received - * bytes. Separates the bytes received over the serial data channel into - * user data and command replies (locked/unlocked) according to the - * current state of the interface. - */ -void gigaset_m10x_input(struct inbuf_t *inbuf) -{ - struct cardstate *cs = inbuf->cs; - unsigned numbytes, procbytes; - - gig_dbg(DEBUG_INTR, "buffer state: %u -> %u", inbuf->head, inbuf->tail); - - while (inbuf->head != inbuf->tail) { - /* check for DLE escape */ - handle_dle(inbuf); - - /* process a contiguous block of bytes */ - numbytes = (inbuf->head > inbuf->tail ? - RBUFSIZE : inbuf->tail) - inbuf->head; - gig_dbg(DEBUG_INTR, "processing %u bytes", numbytes); - /* - * numbytes may be 0 if handle_dle() ate the last byte. - * This does no harm, *_loop() will just return 0 immediately. - */ - - if (cs->mstate == MS_LOCKED) - procbytes = lock_loop(numbytes, inbuf); - else if (inbuf->inputstate & INS_command) - procbytes = cmd_loop(numbytes, inbuf); - else if (cs->bcs->proto2 == L2_HDLC) - procbytes = hdlc_loop(numbytes, inbuf); - else - procbytes = iraw_loop(numbytes, inbuf); - inbuf->head += procbytes; - - /* check for buffer wraparound */ - if (inbuf->head >= RBUFSIZE) - inbuf->head = 0; - - gig_dbg(DEBUG_INTR, "head set to %u", inbuf->head); - } -} -EXPORT_SYMBOL_GPL(gigaset_m10x_input); - - -/* == data output ========================================================== */ - -/* - * Encode a data packet into an octet stuffed HDLC frame with FCS, - * opening and closing flags, preserving headroom data. - * parameters: - * skb skb containing original packet (freed upon return) - * Return value: - * pointer to newly allocated skb containing the result frame - * and the original link layer header, NULL on error - */ -static struct sk_buff *HDLC_Encode(struct sk_buff *skb) -{ - struct sk_buff *hdlc_skb; - __u16 fcs; - unsigned char c; - unsigned char *cp; - int len; - unsigned int stuf_cnt; - - stuf_cnt = 0; - fcs = PPP_INITFCS; - cp = skb->data; - len = skb->len; - while (len--) { - if (muststuff(*cp)) - stuf_cnt++; - fcs = crc_ccitt_byte(fcs, *cp++); - } - fcs ^= 0xffff; /* complement */ - - /* size of new buffer: original size + number of stuffing bytes - * + 2 bytes FCS + 2 stuffing bytes for FCS (if needed) + 2 flag bytes - * + room for link layer header - */ - hdlc_skb = dev_alloc_skb(skb->len + stuf_cnt + 6 + skb->mac_len); - if (!hdlc_skb) { - dev_kfree_skb_any(skb); - return NULL; - } - - /* Copy link layer header into new skb */ - skb_reset_mac_header(hdlc_skb); - skb_reserve(hdlc_skb, skb->mac_len); - memcpy(skb_mac_header(hdlc_skb), skb_mac_header(skb), skb->mac_len); - hdlc_skb->mac_len = skb->mac_len; - - /* Add flag sequence in front of everything.. */ - skb_put_u8(hdlc_skb, PPP_FLAG); - - /* Perform byte stuffing while copying data. */ - while (skb->len--) { - if (muststuff(*skb->data)) { - skb_put_u8(hdlc_skb, PPP_ESCAPE); - skb_put_u8(hdlc_skb, (*skb->data++) ^ PPP_TRANS); - } else - skb_put_u8(hdlc_skb, *skb->data++); - } - - /* Finally add FCS (byte stuffed) and flag sequence */ - c = (fcs & 0x00ff); /* least significant byte first */ - if (muststuff(c)) { - skb_put_u8(hdlc_skb, PPP_ESCAPE); - c ^= PPP_TRANS; - } - skb_put_u8(hdlc_skb, c); - - c = ((fcs >> 8) & 0x00ff); - if (muststuff(c)) { - skb_put_u8(hdlc_skb, PPP_ESCAPE); - c ^= PPP_TRANS; - } - skb_put_u8(hdlc_skb, c); - - skb_put_u8(hdlc_skb, PPP_FLAG); - - dev_kfree_skb_any(skb); - return hdlc_skb; -} - -/* - * Encode a data packet into an octet stuffed raw bit inverted frame, - * preserving headroom data. - * parameters: - * skb skb containing original packet (freed upon return) - * Return value: - * pointer to newly allocated skb containing the result frame - * and the original link layer header, NULL on error - */ -static struct sk_buff *iraw_encode(struct sk_buff *skb) -{ - struct sk_buff *iraw_skb; - unsigned char c; - unsigned char *cp; - int len; - - /* size of new buffer (worst case = every byte must be stuffed): - * 2 * original size + room for link layer header - */ - iraw_skb = dev_alloc_skb(2 * skb->len + skb->mac_len); - if (!iraw_skb) { - dev_kfree_skb_any(skb); - return NULL; - } - - /* copy link layer header into new skb */ - skb_reset_mac_header(iraw_skb); - skb_reserve(iraw_skb, skb->mac_len); - memcpy(skb_mac_header(iraw_skb), skb_mac_header(skb), skb->mac_len); - iraw_skb->mac_len = skb->mac_len; - - /* copy and stuff data */ - cp = skb->data; - len = skb->len; - while (len--) { - c = bitrev8(*cp++); - if (c == DLE_FLAG) - skb_put_u8(iraw_skb, c); - skb_put_u8(iraw_skb, c); - } - dev_kfree_skb_any(skb); - return iraw_skb; -} - -/** - * gigaset_m10x_send_skb() - queue an skb for sending - * @bcs: B channel descriptor structure. - * @skb: data to send. - * - * Called by LL to encode and queue an skb for sending, and start - * transmission if necessary. - * Once the payload data has been transmitted completely, gigaset_skb_sent() - * will be called with the skb's link layer header preserved. - * - * Return value: - * number of bytes accepted for sending (skb->len) if ok, - * error code < 0 (eg. -ENOMEM) on error - */ -int gigaset_m10x_send_skb(struct bc_state *bcs, struct sk_buff *skb) -{ - struct cardstate *cs = bcs->cs; - unsigned len = skb->len; - unsigned long flags; - - if (bcs->proto2 == L2_HDLC) - skb = HDLC_Encode(skb); - else - skb = iraw_encode(skb); - if (!skb) { - dev_err(cs->dev, - "unable to allocate memory for encoding!\n"); - return -ENOMEM; - } - - skb_queue_tail(&bcs->squeue, skb); - spin_lock_irqsave(&cs->lock, flags); - if (cs->connected) - tasklet_schedule(&cs->write_tasklet); - spin_unlock_irqrestore(&cs->lock, flags); - - return len; /* ok so far */ -} -EXPORT_SYMBOL_GPL(gigaset_m10x_send_skb); diff --git a/drivers/staging/isdn/gigaset/bas-gigaset.c b/drivers/staging/isdn/gigaset/bas-gigaset.c deleted file mode 100644 index c334525a5f63..000000000000 --- a/drivers/staging/isdn/gigaset/bas-gigaset.c +++ /dev/null @@ -1,2672 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -/* - * USB driver for Gigaset 307x base via direct USB connection. - * - * Copyright (c) 2001 by Hansjoerg Lipp <hjlipp@web.de>, - * Tilman Schmidt <tilman@imap.cc>, - * Stefan Eilers. - * - * ===================================================================== - * ===================================================================== - */ - -#include "gigaset.h" -#include <linux/usb.h> -#include <linux/module.h> -#include <linux/moduleparam.h> - -/* Version Information */ -#define DRIVER_AUTHOR "Tilman Schmidt <tilman@imap.cc>, Hansjoerg Lipp <hjlipp@web.de>, Stefan Eilers" -#define DRIVER_DESC "USB Driver for Gigaset 307x" - - -/* Module parameters */ - -static int startmode = SM_ISDN; -static int cidmode = 1; - -module_param(startmode, int, S_IRUGO); -module_param(cidmode, int, S_IRUGO); -MODULE_PARM_DESC(startmode, "start in isdn4linux mode"); -MODULE_PARM_DESC(cidmode, "Call-ID mode"); - -#define GIGASET_MINORS 1 -#define GIGASET_MINOR 16 -#define GIGASET_MODULENAME "bas_gigaset" -#define GIGASET_DEVNAME "ttyGB" - -/* length limit according to Siemens 3070usb-protokoll.doc ch. 2.1 */ -#define IF_WRITEBUF 264 - -/* interrupt pipe message size according to ibid. ch. 2.2 */ -#define IP_MSGSIZE 3 - -/* Values for the Gigaset 307x */ -#define USB_GIGA_VENDOR_ID 0x0681 -#define USB_3070_PRODUCT_ID 0x0001 -#define USB_3075_PRODUCT_ID 0x0002 -#define USB_SX303_PRODUCT_ID 0x0021 -#define USB_SX353_PRODUCT_ID 0x0022 - -/* table of devices that work with this driver */ -static const struct usb_device_id gigaset_table[] = { - { USB_DEVICE(USB_GIGA_VENDOR_ID, USB_3070_PRODUCT_ID) }, - { USB_DEVICE(USB_GIGA_VENDOR_ID, USB_3075_PRODUCT_ID) }, - { USB_DEVICE(USB_GIGA_VENDOR_ID, USB_SX303_PRODUCT_ID) }, - { USB_DEVICE(USB_GIGA_VENDOR_ID, USB_SX353_PRODUCT_ID) }, - { } /* Terminating entry */ -}; - -MODULE_DEVICE_TABLE(usb, gigaset_table); - -/*======================= local function prototypes ==========================*/ - -/* function called if a new device belonging to this driver is connected */ -static int gigaset_probe(struct usb_interface *interface, - const struct usb_device_id *id); - -/* Function will be called if the device is unplugged */ -static void gigaset_disconnect(struct usb_interface *interface); - -/* functions called before/after suspend */ -static int gigaset_suspend(struct usb_interface *intf, pm_message_t message); -static int gigaset_resume(struct usb_interface *intf); - -/* functions called before/after device reset */ -static int gigaset_pre_reset(struct usb_interface *intf); -static int gigaset_post_reset(struct usb_interface *intf); - -static int atread_submit(struct cardstate *, int); -static void stopurbs(struct bas_bc_state *); -static int req_submit(struct bc_state *, int, int, int); -static int atwrite_submit(struct cardstate *, unsigned char *, int); -static int start_cbsend(struct cardstate *); - -/*============================================================================*/ - -struct bas_cardstate { - struct usb_device *udev; /* USB device pointer */ - struct cardstate *cs; - struct usb_interface *interface; /* interface for this device */ - unsigned char minor; /* starting minor number */ - - struct urb *urb_ctrl; /* control pipe default URB */ - struct usb_ctrlrequest dr_ctrl; - struct timer_list timer_ctrl; /* control request timeout */ - int retry_ctrl; - - struct timer_list timer_atrdy; /* AT command ready timeout */ - struct urb *urb_cmd_out; /* for sending AT commands */ - struct usb_ctrlrequest dr_cmd_out; - int retry_cmd_out; - - struct urb *urb_cmd_in; /* for receiving AT replies */ - struct usb_ctrlrequest dr_cmd_in; - struct timer_list timer_cmd_in; /* receive request timeout */ - unsigned char *rcvbuf; /* AT reply receive buffer */ - - struct urb *urb_int_in; /* URB for interrupt pipe */ - unsigned char *int_in_buf; - struct work_struct int_in_wq; /* for usb_clear_halt() */ - struct timer_list timer_int_in; /* int read retry delay */ - int retry_int_in; - - spinlock_t lock; /* locks all following */ - int basstate; /* bitmap (BS_*) */ - int pending; /* uncompleted base request */ - wait_queue_head_t waitqueue; - int rcvbuf_size; /* size of AT receive buffer */ - /* 0: no receive in progress */ - int retry_cmd_in; /* receive req retry count */ -}; - -/* status of direct USB connection to 307x base (bits in basstate) */ -#define BS_ATOPEN 0x001 /* AT channel open */ -#define BS_B1OPEN 0x002 /* B channel 1 open */ -#define BS_B2OPEN 0x004 /* B channel 2 open */ -#define BS_ATREADY 0x008 /* base ready for AT command */ -#define BS_INIT 0x010 /* base has signalled INIT_OK */ -#define BS_ATTIMER 0x020 /* waiting for HD_READY_SEND_ATDATA */ -#define BS_ATRDPEND 0x040 /* urb_cmd_in in use */ -#define BS_ATWRPEND 0x080 /* urb_cmd_out in use */ -#define BS_SUSPEND 0x100 /* USB port suspended */ -#define BS_RESETTING 0x200 /* waiting for HD_RESET_INTERRUPT_PIPE_ACK */ - - -static struct gigaset_driver *driver; - -/* usb specific object needed to register this driver with the usb subsystem */ -static struct usb_driver gigaset_usb_driver = { - .name = GIGASET_MODULENAME, - .probe = gigaset_probe, - .disconnect = gigaset_disconnect, - .id_table = gigaset_table, - .suspend = gigaset_suspend, - .resume = gigaset_resume, - .reset_resume = gigaset_post_reset, - .pre_reset = gigaset_pre_reset, - .post_reset = gigaset_post_reset, - .disable_hub_initiated_lpm = 1, -}; - -/* get message text for usb_submit_urb return code - */ -static char *get_usb_rcmsg(int rc) -{ - static char unkmsg[28]; - - switch (rc) { - case 0: - return "success"; - case -ENOMEM: - return "out of memory"; - case -ENODEV: - return "device not present"; - case -ENOENT: - return "endpoint not present"; - case -ENXIO: - return "URB type not supported"; - case -EINVAL: - return "invalid argument"; - case -EAGAIN: - return "start frame too early or too much scheduled"; - case -EFBIG: - return "too many isoc frames requested"; - case -EPIPE: - return "endpoint stalled"; - case -EMSGSIZE: - return "invalid packet size"; - case -ENOSPC: - return "would overcommit USB bandwidth"; - case -ESHUTDOWN: - return "device shut down"; - case -EPERM: - return "reject flag set"; - case -EHOSTUNREACH: - return "device suspended"; - default: - snprintf(unkmsg, sizeof(unkmsg), "unknown error %d", rc); - return unkmsg; - } -} - -/* get message text for USB status code - */ -static char *get_usb_statmsg(int status) -{ - static char unkmsg[28]; - - switch (status) { - case 0: - return "success"; - case -ENOENT: - return "unlinked (sync)"; - case -EINPROGRESS: - return "URB still pending"; - case -EPROTO: - return "bitstuff error, timeout, or unknown USB error"; - case -EILSEQ: - return "CRC mismatch, timeout, or unknown USB error"; - case -ETIME: - return "USB response timeout"; - case -EPIPE: - return "endpoint stalled"; - case -ECOMM: - return "IN buffer overrun"; - case -ENOSR: - return "OUT buffer underrun"; - case -EOVERFLOW: - return "endpoint babble"; - case -EREMOTEIO: - return "short packet"; - case -ENODEV: - return "device removed"; - case -EXDEV: - return "partial isoc transfer"; - case -EINVAL: - return "ISO madness"; - case -ECONNRESET: - return "unlinked (async)"; - case -ESHUTDOWN: - return "device shut down"; - default: - snprintf(unkmsg, sizeof(unkmsg), "unknown status %d", status); - return unkmsg; - } -} - -/* usb_pipetype_str - * retrieve string representation of USB pipe type - */ -static inline char *usb_pipetype_str(int pipe) -{ - if (usb_pipeisoc(pipe)) - return "Isoc"; - if (usb_pipeint(pipe)) - return "Int"; - if (usb_pipecontrol(pipe)) - return "Ctrl"; - if (usb_pipebulk(pipe)) - return "Bulk"; - return "?"; -} - -/* dump_urb - * write content of URB to syslog for debugging - */ -static inline void dump_urb(enum debuglevel level, const char *tag, - struct urb *urb) -{ -#ifdef CONFIG_GIGASET_DEBUG - int i; - gig_dbg(level, "%s urb(0x%08lx)->{", tag, (unsigned long) urb); - if (urb) { - gig_dbg(level, - " dev=0x%08lx, pipe=%s:EP%d/DV%d:%s, " - "hcpriv=0x%08lx, transfer_flags=0x%x,", - (unsigned long) urb->dev, - usb_pipetype_str(urb->pipe), - usb_pipeendpoint(urb->pipe), usb_pipedevice(urb->pipe), - usb_pipein(urb->pipe) ? "in" : "out", - (unsigned long) urb->hcpriv, - urb->transfer_flags); - gig_dbg(level, - " transfer_buffer=0x%08lx[%d], actual_length=%d, " - "setup_packet=0x%08lx,", - (unsigned long) urb->transfer_buffer, - urb->transfer_buffer_length, urb->actual_length, - (unsigned long) urb->setup_packet); - gig_dbg(level, - " start_frame=%d, number_of_packets=%d, interval=%d, " - "error_count=%d,", - urb->start_frame, urb->number_of_packets, urb->interval, - urb->error_count); - gig_dbg(level, - " context=0x%08lx, complete=0x%08lx, " - "iso_frame_desc[]={", - (unsigned long) urb->context, - (unsigned long) urb->complete); - for (i = 0; i < urb->number_of_packets; i++) { - struct usb_iso_packet_descriptor *pifd - = &urb->iso_frame_desc[i]; - gig_dbg(level, - " {offset=%u, length=%u, actual_length=%u, " - "status=%u}", - pifd->offset, pifd->length, pifd->actual_length, - pifd->status); - } - } - gig_dbg(level, "}}"); -#endif -} - -/* read/set modem control bits etc. (m10x only) */ -static int gigaset_set_modem_ctrl(struct cardstate *cs, unsigned old_state, - unsigned new_state) -{ - return -EINVAL; -} - -static int gigaset_baud_rate(struct cardstate *cs, unsigned cflag) -{ - return -EINVAL; -} - -static int gigaset_set_line_ctrl(struct cardstate *cs, unsigned cflag) -{ - return -EINVAL; -} - -/* set/clear bits in base connection state, return previous state - */ -static inline int update_basstate(struct bas_cardstate *ucs, - int set, int clear) -{ - unsigned long flags; - int state; - - spin_lock_irqsave(&ucs->lock, flags); - state = ucs->basstate; - ucs->basstate = (state & ~clear) | set; - spin_unlock_irqrestore(&ucs->lock, flags); - return state; -} - -/* error_hangup - * hang up any existing connection because of an unrecoverable error - * This function may be called from any context and takes care of scheduling - * the necessary actions for execution outside of interrupt context. - * cs->lock must not be held. - * argument: - * B channel control structure - */ -static inline void error_hangup(struct bc_state *bcs) -{ - struct cardstate *cs = bcs->cs; - - gigaset_add_event(cs, &bcs->at_state, EV_HUP, NULL, 0, NULL); - gigaset_schedule_event(cs); -} - -/* error_reset - * reset Gigaset device because of an unrecoverable error - * This function may be called from any context, and takes care of - * scheduling the necessary actions for execution outside of interrupt context. - * cs->hw.bas->lock must not be held. - * argument: - * controller state structure - */ -static inline void error_reset(struct cardstate *cs) -{ - /* reset interrupt pipe to recover (ignore errors) */ - update_basstate(cs->hw.bas, BS_RESETTING, 0); - if (req_submit(cs->bcs, HD_RESET_INTERRUPT_PIPE, 0, BAS_TIMEOUT)) - /* submission failed, escalate to USB port reset */ - usb_queue_reset_device(cs->hw.bas->interface); -} - -/* check_pending - * check for completion of pending control request - * parameter: - * ucs hardware specific controller state structure - */ -static void check_pending(struct bas_cardstate *ucs) -{ - unsigned long flags; - - spin_lock_irqsave(&ucs->lock, flags); - switch (ucs->pending) { - case 0: - break; - case HD_OPEN_ATCHANNEL: - if (ucs->basstate & BS_ATOPEN) - ucs->pending = 0; - break; - case HD_OPEN_B1CHANNEL: - if (ucs->basstate & BS_B1OPEN) - ucs->pending = 0; - break; - case HD_OPEN_B2CHANNEL: - if (ucs->basstate & BS_B2OPEN) - ucs->pending = 0; - break; - case HD_CLOSE_ATCHANNEL: - if (!(ucs->basstate & BS_ATOPEN)) - ucs->pending = 0; - break; - case HD_CLOSE_B1CHANNEL: - if (!(ucs->basstate & BS_B1OPEN)) - ucs->pending = 0; - break; - case HD_CLOSE_B2CHANNEL: - if (!(ucs->basstate & BS_B2OPEN)) - ucs->pending = 0; - break; - case HD_DEVICE_INIT_ACK: /* no reply expected */ - ucs->pending = 0; - break; - case HD_RESET_INTERRUPT_PIPE: - if (!(ucs->basstate & BS_RESETTING)) - ucs->pending = 0; - break; - /* - * HD_READ_ATMESSAGE and HD_WRITE_ATMESSAGE are handled separately - * and should never end up here - */ - default: - dev_warn(&ucs->interface->dev, - "unknown pending request 0x%02x cleared\n", - ucs->pending); - ucs->pending = 0; - } - - if (!ucs->pending) - del_timer(&ucs->timer_ctrl); - - spin_unlock_irqrestore(&ucs->lock, flags); -} - -/* cmd_in_timeout - * timeout routine for command input request - * argument: - * controller state structure - */ -static void cmd_in_timeout(struct timer_list *t) -{ - struct bas_cardstate *ucs = from_timer(ucs, t, timer_cmd_in); - struct cardstate *cs = ucs->cs; - int rc; - - if (!ucs->rcvbuf_size) { - gig_dbg(DEBUG_USBREQ, "%s: no receive in progress", __func__); - return; - } - - if (ucs->retry_cmd_in++ >= BAS_RETRY) { - dev_err(cs->dev, - "control read: timeout, giving up after %d tries\n", - ucs->retry_cmd_in); - kfree(ucs->rcvbuf); - ucs->rcvbuf = NULL; - ucs->rcvbuf_size = 0; - error_reset(cs); - return; - } - - gig_dbg(DEBUG_USBREQ, "%s: timeout, retry %d", - __func__, ucs->retry_cmd_in); - rc = atread_submit(cs, BAS_TIMEOUT); - if (rc < 0) { - kfree(ucs->rcvbuf); - ucs->rcvbuf = NULL; - ucs->rcvbuf_size = 0; - if (rc != -ENODEV) - error_reset(cs); - } -} - -/* read_ctrl_callback - * USB completion handler for control pipe input - * called by the USB subsystem in interrupt context - * parameter: - * urb USB request block - * urb->context = inbuf structure for controller state - */ -static void read_ctrl_callback(struct urb *urb) -{ - struct inbuf_t *inbuf = urb->context; - struct cardstate *cs = inbuf->cs; - struct bas_cardstate *ucs = cs->hw.bas; - int status = urb->status; - unsigned numbytes; - int rc; - - update_basstate(ucs, 0, BS_ATRDPEND); - wake_up(&ucs->waitqueue); - del_timer(&ucs->timer_cmd_in); - - switch (status) { - case 0: /* normal completion */ - numbytes = urb->actual_length; - if (unlikely(numbytes != ucs->rcvbuf_size)) { - dev_warn(cs->dev, - "control read: received %d chars, expected %d\n", - numbytes, ucs->rcvbuf_size); - if (numbytes > ucs->rcvbuf_size) - numbytes = ucs->rcvbuf_size; - } - - /* copy received bytes to inbuf, notify event layer */ - if (gigaset_fill_inbuf(inbuf, ucs->rcvbuf, numbytes)) { - gig_dbg(DEBUG_INTR, "%s-->BH", __func__); - gigaset_schedule_event(cs); - } - break; - - case -ENOENT: /* cancelled */ - case -ECONNRESET: /* cancelled (async) */ - case -EINPROGRESS: /* pending */ - case -ENODEV: /* device removed */ - case -ESHUTDOWN: /* device shut down */ - /* no further action necessary */ - gig_dbg(DEBUG_USBREQ, "%s: %s", - __func__, get_usb_statmsg(status)); - break; - - default: /* other errors: retry */ - if (ucs->retry_cmd_in++ < BAS_RETRY) { - gig_dbg(DEBUG_USBREQ, "%s: %s, retry %d", __func__, - get_usb_statmsg(status), ucs->retry_cmd_in); - rc = atread_submit(cs, BAS_TIMEOUT); - if (rc >= 0) - /* successfully resubmitted, skip freeing */ - return; - if (rc == -ENODEV) - /* disconnect, no further action necessary */ - break; - } - dev_err(cs->dev, "control read: %s, giving up after %d tries\n", - get_usb_statmsg(status), ucs->retry_cmd_in); - error_reset(cs); - } - - /* read finished, free buffer */ - kfree(ucs->rcvbuf); - ucs->rcvbuf = NULL; - ucs->rcvbuf_size = 0; -} - -/* atread_submit - * submit an HD_READ_ATMESSAGE command URB and optionally start a timeout - * parameters: - * cs controller state structure - * timeout timeout in 1/10 sec., 0: none - * return value: - * 0 on success - * -EBUSY if another request is pending - * any URB submission error code - */ -static int atread_submit(struct cardstate *cs, int timeout) -{ - struct bas_cardstate *ucs = cs->hw.bas; - int basstate; - int ret; - - gig_dbg(DEBUG_USBREQ, "-------> HD_READ_ATMESSAGE (%d)", - ucs->rcvbuf_size); - - basstate = update_basstate(ucs, BS_ATRDPEND, 0); - if (basstate & BS_ATRDPEND) { - dev_err(cs->dev, - "could not submit HD_READ_ATMESSAGE: URB busy\n"); - return -EBUSY; - } - - if (basstate & BS_SUSPEND) { - dev_notice(cs->dev, - "HD_READ_ATMESSAGE not submitted, " - "suspend in progress\n"); - update_basstate(ucs, 0, BS_ATRDPEND); - /* treat like disconnect */ - return -ENODEV; - } - - ucs->dr_cmd_in.bRequestType = IN_VENDOR_REQ; - ucs->dr_cmd_in.bRequest = HD_READ_ATMESSAGE; - ucs->dr_cmd_in.wValue = 0; - ucs->dr_cmd_in.wIndex = 0; - ucs->dr_cmd_in.wLength = cpu_to_le16(ucs->rcvbuf_size); - usb_fill_control_urb(ucs->urb_cmd_in, ucs->udev, - usb_rcvctrlpipe(ucs->udev, 0), - (unsigned char *) &ucs->dr_cmd_in, - ucs->rcvbuf, ucs->rcvbuf_size, - read_ctrl_callback, cs->inbuf); - - ret = usb_submit_urb(ucs->urb_cmd_in, GFP_ATOMIC); - if (ret != 0) { - update_basstate(ucs, 0, BS_ATRDPEND); - dev_err(cs->dev, "could not submit HD_READ_ATMESSAGE: %s\n", - get_usb_rcmsg(ret)); - return ret; - } - - if (timeout > 0) { - gig_dbg(DEBUG_USBREQ, "setting timeout of %d/10 secs", timeout); - mod_timer(&ucs->timer_cmd_in, jiffies + timeout * HZ / 10); - } - return 0; -} - -/* int_in_work - * workqueue routine to clear halt on interrupt in endpoint - */ - -static void int_in_work(struct work_struct *work) -{ - struct bas_cardstate *ucs = - container_of(work, struct bas_cardstate, int_in_wq); - struct urb *urb = ucs->urb_int_in; - struct cardstate *cs = urb->context; - int rc; - - /* clear halt condition */ - rc = usb_clear_halt(ucs->udev, urb->pipe); - gig_dbg(DEBUG_USBREQ, "clear_halt: %s", get_usb_rcmsg(rc)); - if (rc == 0) - /* success, resubmit interrupt read URB */ - rc = usb_submit_urb(urb, GFP_ATOMIC); - - switch (rc) { - case 0: /* success */ - case -ENODEV: /* device gone */ - case -EINVAL: /* URB already resubmitted, or terminal badness */ - break; - default: /* failure: try to recover by resetting the device */ - dev_err(cs->dev, "clear halt failed: %s\n", get_usb_rcmsg(rc)); - rc = usb_lock_device_for_reset(ucs->udev, ucs->interface); - if (rc == 0) { - rc = usb_reset_device(ucs->udev); - usb_unlock_device(ucs->udev); - } - } - ucs->retry_int_in = 0; -} - -/* int_in_resubmit - * timer routine for interrupt read delayed resubmit - * argument: - * controller state structure - */ -static void int_in_resubmit(struct timer_list *t) -{ - struct bas_cardstate *ucs = from_timer(ucs, t, timer_int_in); - struct cardstate *cs = ucs->cs; - int rc; - - if (ucs->retry_int_in++ >= BAS_RETRY) { - dev_err(cs->dev, "interrupt read: giving up after %d tries\n", - ucs->retry_int_in); - usb_queue_reset_device(ucs->interface); - return; - } - - gig_dbg(DEBUG_USBREQ, "%s: retry %d", __func__, ucs->retry_int_in); - rc = usb_submit_urb(ucs->urb_int_in, GFP_ATOMIC); - if (rc != 0 && rc != -ENODEV) { - dev_err(cs->dev, "could not resubmit interrupt URB: %s\n", - get_usb_rcmsg(rc)); - usb_queue_reset_device(ucs->interface); - } -} - -/* read_int_callback - * USB completion handler for interrupt pipe input - * called by the USB subsystem in interrupt context - * parameter: - * urb USB request block - * urb->context = controller state structure - */ -static void read_int_callback(struct urb *urb) -{ - struct cardstate *cs = urb->context; - struct bas_cardstate *ucs = cs->hw.bas; - struct bc_state *bcs; - int status = urb->status; - unsigned long flags; - int rc; - unsigned l; - int channel; - - switch (status) { - case 0: /* success */ - ucs->retry_int_in = 0; - break; - case -EPIPE: /* endpoint stalled */ - schedule_work(&ucs->int_in_wq); - /* fall through */ - case -ENOENT: /* cancelled */ - case -ECONNRESET: /* cancelled (async) */ - case -EINPROGRESS: /* pending */ - case -ENODEV: /* device removed */ - case -ESHUTDOWN: /* device shut down */ - /* no further action necessary */ - gig_dbg(DEBUG_USBREQ, "%s: %s", - __func__, get_usb_statmsg(status)); - return; - case -EPROTO: /* protocol error or unplug */ - case -EILSEQ: - case -ETIME: - /* resubmit after delay */ - gig_dbg(DEBUG_USBREQ, "%s: %s", - __func__, get_usb_statmsg(status)); - mod_timer(&ucs->timer_int_in, jiffies + HZ / 10); - return; - default: /* other errors: just resubmit */ - dev_warn(cs->dev, "interrupt read: %s\n", - get_usb_statmsg(status)); - goto resubmit; - } - - /* drop incomplete packets even if the missing bytes wouldn't matter */ - if (unlikely(urb->actual_length < IP_MSGSIZE)) { - dev_warn(cs->dev, "incomplete interrupt packet (%d bytes)\n", - urb->actual_length); - goto resubmit; - } - - l = (unsigned) ucs->int_in_buf[1] + - (((unsigned) ucs->int_in_buf[2]) << 8); - - gig_dbg(DEBUG_USBREQ, "<-------%d: 0x%02x (%u [0x%02x 0x%02x])", - urb->actual_length, (int)ucs->int_in_buf[0], l, - (int)ucs->int_in_buf[1], (int)ucs->int_in_buf[2]); - - channel = 0; - - switch (ucs->int_in_buf[0]) { - case HD_DEVICE_INIT_OK: - update_basstate(ucs, BS_INIT, 0); - break; - - case HD_READY_SEND_ATDATA: - del_timer(&ucs->timer_atrdy); - update_basstate(ucs, BS_ATREADY, BS_ATTIMER); - start_cbsend(cs); - break; - - case HD_OPEN_B2CHANNEL_ACK: - ++channel; - /* fall through */ - case HD_OPEN_B1CHANNEL_ACK: - bcs = cs->bcs + channel; - update_basstate(ucs, BS_B1OPEN << channel, 0); - gigaset_bchannel_up(bcs); - break; - - case HD_OPEN_ATCHANNEL_ACK: - update_basstate(ucs, BS_ATOPEN, 0); - start_cbsend(cs); - break; - - case HD_CLOSE_B2CHANNEL_ACK: - ++channel; - /* fall through */ - case HD_CLOSE_B1CHANNEL_ACK: - bcs = cs->bcs + channel; - update_basstate(ucs, 0, BS_B1OPEN << channel); - stopurbs(bcs->hw.bas); - gigaset_bchannel_down(bcs); - break; - - case HD_CLOSE_ATCHANNEL_ACK: - update_basstate(ucs, 0, BS_ATOPEN); - break; - - case HD_B2_FLOW_CONTROL: - ++channel; - /* fall through */ - case HD_B1_FLOW_CONTROL: - bcs = cs->bcs + channel; - atomic_add((l - BAS_NORMFRAME) * BAS_CORRFRAMES, - &bcs->hw.bas->corrbytes); - gig_dbg(DEBUG_ISO, - "Flow control (channel %d, sub %d): 0x%02x => %d", - channel, bcs->hw.bas->numsub, l, - atomic_read(&bcs->hw.bas->corrbytes)); - break; - - case HD_RECEIVEATDATA_ACK: /* AT response ready to be received */ - if (!l) { - dev_warn(cs->dev, - "HD_RECEIVEATDATA_ACK with length 0 ignored\n"); - break; - } - spin_lock_irqsave(&cs->lock, flags); - if (ucs->basstate & BS_ATRDPEND) { - spin_unlock_irqrestore(&cs->lock, flags); - dev_warn(cs->dev, - "HD_RECEIVEATDATA_ACK(%d) during HD_READ_ATMESSAGE(%d) ignored\n", - l, ucs->rcvbuf_size); - break; - } - if (ucs->rcvbuf_size) { - /* throw away previous buffer - we have no queue */ - dev_err(cs->dev, - "receive AT data overrun, %d bytes lost\n", - ucs->rcvbuf_size); - kfree(ucs->rcvbuf); - ucs->rcvbuf_size = 0; - } - ucs->rcvbuf = kmalloc(l, GFP_ATOMIC); - if (ucs->rcvbuf == NULL) { - spin_unlock_irqrestore(&cs->lock, flags); - dev_err(cs->dev, "out of memory receiving AT data\n"); - break; - } - ucs->rcvbuf_size = l; - ucs->retry_cmd_in = 0; - rc = atread_submit(cs, BAS_TIMEOUT); - if (rc < 0) { - kfree(ucs->rcvbuf); - ucs->rcvbuf = NULL; - ucs->rcvbuf_size = 0; - } - spin_unlock_irqrestore(&cs->lock, flags); - if (rc < 0 && rc != -ENODEV) - error_reset(cs); - break; - - case HD_RESET_INTERRUPT_PIPE_ACK: - update_basstate(ucs, 0, BS_RESETTING); - dev_notice(cs->dev, "interrupt pipe reset\n"); - break; - - case HD_SUSPEND_END: - gig_dbg(DEBUG_USBREQ, "HD_SUSPEND_END"); - break; - - default: - dev_warn(cs->dev, - "unknown Gigaset signal 0x%02x (%u) ignored\n", - (int) ucs->int_in_buf[0], l); - } - - check_pending(ucs); - wake_up(&ucs->waitqueue); - -resubmit: - rc = usb_submit_urb(urb, GFP_ATOMIC); - if (unlikely(rc != 0 && rc != -ENODEV)) { - dev_err(cs->dev, "could not resubmit interrupt URB: %s\n", - get_usb_rcmsg(rc)); - error_reset(cs); - } -} - -/* read_iso_callback - * USB completion handler for B channel isochronous input - * called by the USB subsystem in interrupt context - * parameter: - * urb USB request block of completed request - * urb->context = bc_state structure - */ -static void read_iso_callback(struct urb *urb) -{ - struct bc_state *bcs; - struct bas_bc_state *ubc; - int status = urb->status; - unsigned long flags; - int i, rc; - - /* status codes not worth bothering the tasklet with */ - if (unlikely(status == -ENOENT || - status == -ECONNRESET || - status == -EINPROGRESS || - status == -ENODEV || - status == -ESHUTDOWN)) { - gig_dbg(DEBUG_ISO, "%s: %s", - __func__, get_usb_statmsg(status)); - return; - } - - bcs = urb->context; - ubc = bcs->hw.bas; - - spin_lock_irqsave(&ubc->isoinlock, flags); - if (likely(ubc->isoindone == NULL)) { - /* pass URB to tasklet */ - ubc->isoindone = urb; - ubc->isoinstatus = status; - tasklet_hi_schedule(&ubc->rcvd_tasklet); - } else { - /* tasklet still busy, drop data and resubmit URB */ - gig_dbg(DEBUG_ISO, "%s: overrun", __func__); - ubc->loststatus = status; - for (i = 0; i < BAS_NUMFRAMES; i++) { - ubc->isoinlost += urb->iso_frame_desc[i].actual_length; - if (unlikely(urb->iso_frame_desc[i].status != 0 && - urb->iso_frame_desc[i].status != -EINPROGRESS)) - ubc->loststatus = urb->iso_frame_desc[i].status; - urb->iso_frame_desc[i].status = 0; - urb->iso_frame_desc[i].actual_length = 0; - } - if (likely(ubc->running)) { - /* urb->dev is clobbered by USB subsystem */ - urb->dev = bcs->cs->hw.bas->udev; - urb->transfer_flags = URB_ISO_ASAP; - urb->number_of_packets = BAS_NUMFRAMES; - rc = usb_submit_urb(urb, GFP_ATOMIC); - if (unlikely(rc != 0 && rc != -ENODEV)) { - dev_err(bcs->cs->dev, - "could not resubmit isoc read URB: %s\n", - get_usb_rcmsg(rc)); - dump_urb(DEBUG_ISO, "isoc read", urb); - error_hangup(bcs); - } - } - } - spin_unlock_irqrestore(&ubc->isoinlock, flags); -} - -/* write_iso_callback - * USB completion handler for B channel isochronous output - * called by the USB subsystem in interrupt context - * parameter: - * urb USB request block of completed request - * urb->context = isow_urbctx_t structure - */ -static void write_iso_callback(struct urb *urb) -{ - struct isow_urbctx_t *ucx; - struct bas_bc_state *ubc; - int status = urb->status; - unsigned long flags; - - /* status codes not worth bothering the tasklet with */ - if (unlikely(status == -ENOENT || - status == -ECONNRESET || - status == -EINPROGRESS || - status == -ENODEV || - status == -ESHUTDOWN)) { - gig_dbg(DEBUG_ISO, "%s: %s", - __func__, get_usb_statmsg(status)); - return; - } - - /* pass URB context to tasklet */ - ucx = urb->context; - ubc = ucx->bcs->hw.bas; - ucx->status = status; - - spin_lock_irqsave(&ubc->isooutlock, flags); - ubc->isooutovfl = ubc->isooutdone; - ubc->isooutdone = ucx; - spin_unlock_irqrestore(&ubc->isooutlock, flags); - tasklet_hi_schedule(&ubc->sent_tasklet); -} - -/* starturbs - * prepare and submit USB request blocks for isochronous input and output - * argument: - * B channel control structure - * return value: - * 0 on success - * < 0 on error (no URBs submitted) - */ -static int starturbs(struct bc_state *bcs) -{ - struct usb_device *udev = bcs->cs->hw.bas->udev; - struct bas_bc_state *ubc = bcs->hw.bas; - struct urb *urb; - int j, k; - int rc; - - /* initialize L2 reception */ - if (bcs->proto2 == L2_HDLC) - bcs->inputstate |= INS_flag_hunt; - - /* submit all isochronous input URBs */ - ubc->running = 1; - for (k = 0; k < BAS_INURBS; k++) { - urb = ubc->isoinurbs[k]; - if (!urb) { - rc = -EFAULT; - goto error; - } - usb_fill_int_urb(urb, udev, - usb_rcvisocpipe(udev, 3 + 2 * bcs->channel), - ubc->isoinbuf + k * BAS_INBUFSIZE, - BAS_INBUFSIZE, read_iso_callback, bcs, - BAS_FRAMETIME); - - urb->transfer_flags = URB_ISO_ASAP; - urb->number_of_packets = BAS_NUMFRAMES; - for (j = 0; j < BAS_NUMFRAMES; j++) { - urb->iso_frame_desc[j].offset = j * BAS_MAXFRAME; - urb->iso_frame_desc[j].length = BAS_MAXFRAME; - urb->iso_frame_desc[j].status = 0; - urb->iso_frame_desc[j].actual_length = 0; - } - - dump_urb(DEBUG_ISO, "Initial isoc read", urb); - rc = usb_submit_urb(urb, GFP_ATOMIC); - if (rc != 0) - goto error; - } - - /* initialize L2 transmission */ - gigaset_isowbuf_init(ubc->isooutbuf, PPP_FLAG); - - /* set up isochronous output URBs for flag idling */ - for (k = 0; k < BAS_OUTURBS; ++k) { - urb = ubc->isoouturbs[k].urb; - if (!urb) { - rc = -EFAULT; - goto error; - } - usb_fill_int_urb(urb, udev, - usb_sndisocpipe(udev, 4 + 2 * bcs->channel), - ubc->isooutbuf->data, - sizeof(ubc->isooutbuf->data), - write_iso_callback, &ubc->isoouturbs[k], - BAS_FRAMETIME); - - urb->transfer_flags = URB_ISO_ASAP; - urb->number_of_packets = BAS_NUMFRAMES; - for (j = 0; j < BAS_NUMFRAMES; ++j) { - urb->iso_frame_desc[j].offset = BAS_OUTBUFSIZE; - urb->iso_frame_desc[j].length = BAS_NORMFRAME; - urb->iso_frame_desc[j].status = 0; - urb->iso_frame_desc[j].actual_length = 0; - } - ubc->isoouturbs[k].limit = -1; - } - - /* keep one URB free, submit the others */ - for (k = 0; k < BAS_OUTURBS - 1; ++k) { - dump_urb(DEBUG_ISO, "Initial isoc write", urb); - rc = usb_submit_urb(ubc->isoouturbs[k].urb, GFP_ATOMIC); - if (rc != 0) - goto error; - } - dump_urb(DEBUG_ISO, "Initial isoc write (free)", urb); - ubc->isooutfree = &ubc->isoouturbs[BAS_OUTURBS - 1]; - ubc->isooutdone = ubc->isooutovfl = NULL; - return 0; -error: - stopurbs(ubc); - return rc; -} - -/* stopurbs - * cancel the USB request blocks for isochronous input and output - * errors are silently ignored - * argument: - * B channel control structure - */ -static void stopurbs(struct bas_bc_state *ubc) -{ - int k, rc; - - ubc->running = 0; - - for (k = 0; k < BAS_INURBS; ++k) { - rc = usb_unlink_urb(ubc->isoinurbs[k]); - gig_dbg(DEBUG_ISO, - "%s: isoc input URB %d unlinked, result = %s", - __func__, k, get_usb_rcmsg(rc)); - } - - for (k = 0; k < BAS_OUTURBS; ++k) { - rc = usb_unlink_urb(ubc->isoouturbs[k].urb); - gig_dbg(DEBUG_ISO, - "%s: isoc output URB %d unlinked, result = %s", - __func__, k, get_usb_rcmsg(rc)); - } -} - -/* Isochronous Write - Bottom Half */ -/* =============================== */ - -/* submit_iso_write_urb - * fill and submit the next isochronous write URB - * parameters: - * ucx context structure containing URB - * return value: - * number of frames submitted in URB - * 0 if URB not submitted because no data available (isooutbuf busy) - * error code < 0 on error - */ -static int submit_iso_write_urb(struct isow_urbctx_t *ucx) -{ - struct urb *urb = ucx->urb; - struct bas_bc_state *ubc = ucx->bcs->hw.bas; - struct usb_iso_packet_descriptor *ifd; - int corrbytes, nframe, rc; - - /* urb->dev is clobbered by USB subsystem */ - urb->dev = ucx->bcs->cs->hw.bas->udev; - urb->transfer_flags = URB_ISO_ASAP; - urb->transfer_buffer = ubc->isooutbuf->data; - urb->transfer_buffer_length = sizeof(ubc->isooutbuf->data); - - for (nframe = 0; nframe < BAS_NUMFRAMES; nframe++) { - ifd = &urb->iso_frame_desc[nframe]; - - /* compute frame length according to flow control */ - ifd->length = BAS_NORMFRAME; - corrbytes = atomic_read(&ubc->corrbytes); - if (corrbytes != 0) { - gig_dbg(DEBUG_ISO, "%s: corrbytes=%d", - __func__, corrbytes); - if (corrbytes > BAS_HIGHFRAME - BAS_NORMFRAME) - corrbytes = BAS_HIGHFRAME - BAS_NORMFRAME; - else if (corrbytes < BAS_LOWFRAME - BAS_NORMFRAME) - corrbytes = BAS_LOWFRAME - BAS_NORMFRAME; - ifd->length += corrbytes; - atomic_add(-corrbytes, &ubc->corrbytes); - } - - /* retrieve block of data to send */ - rc = gigaset_isowbuf_getbytes(ubc->isooutbuf, ifd->length); - if (rc < 0) { - if (rc == -EBUSY) { - gig_dbg(DEBUG_ISO, - "%s: buffer busy at frame %d", - __func__, nframe); - /* tasklet will be restarted from - gigaset_isoc_send_skb() */ - } else { - dev_err(ucx->bcs->cs->dev, - "%s: buffer error %d at frame %d\n", - __func__, rc, nframe); - return rc; - } - break; - } - ifd->offset = rc; - ucx->limit = ubc->isooutbuf->nextread; - ifd->status = 0; - ifd->actual_length = 0; - } - if (unlikely(nframe == 0)) - return 0; /* no data to send */ - urb->number_of_packets = nframe; - - rc = usb_submit_urb(urb, GFP_ATOMIC); - if (unlikely(rc)) { - if (rc == -ENODEV) - /* device removed - give up silently */ - gig_dbg(DEBUG_ISO, "%s: disconnected", __func__); - else - dev_err(ucx->bcs->cs->dev, - "could not submit isoc write URB: %s\n", - get_usb_rcmsg(rc)); - return rc; - } - ++ubc->numsub; - return nframe; -} - -/* write_iso_tasklet - * tasklet scheduled when an isochronous output URB from the Gigaset device - * has completed - * parameter: - * data B channel state structure - */ -static void write_iso_tasklet(unsigned long data) -{ - struct bc_state *bcs = (struct bc_state *) data; - struct bas_bc_state *ubc = bcs->hw.bas; - struct cardstate *cs = bcs->cs; - struct isow_urbctx_t *done, *next, *ovfl; - struct urb *urb; - int status; - struct usb_iso_packet_descriptor *ifd; - unsigned long flags; - int i; - struct sk_buff *skb; - int len; - int rc; - - /* loop while completed URBs arrive in time */ - for (;;) { - if (unlikely(!(ubc->running))) { - gig_dbg(DEBUG_ISO, "%s: not running", __func__); - return; - } - - /* retrieve completed URBs */ - spin_lock_irqsave(&ubc->isooutlock, flags); - done = ubc->isooutdone; - ubc->isooutdone = NULL; - ovfl = ubc->isooutovfl; - ubc->isooutovfl = NULL; - spin_unlock_irqrestore(&ubc->isooutlock, flags); - if (ovfl) { - dev_err(cs->dev, "isoc write underrun\n"); - error_hangup(bcs); - break; - } - if (!done) - break; - - /* submit free URB if available */ - spin_lock_irqsave(&ubc->isooutlock, flags); - next = ubc->isooutfree; - ubc->isooutfree = NULL; - spin_unlock_irqrestore(&ubc->isooutlock, flags); - if (next) { - rc = submit_iso_write_urb(next); - if (unlikely(rc <= 0 && rc != -ENODEV)) { - /* could not submit URB, put it back */ - spin_lock_irqsave(&ubc->isooutlock, flags); - if (ubc->isooutfree == NULL) { - ubc->isooutfree = next; - next = NULL; - } - spin_unlock_irqrestore(&ubc->isooutlock, flags); - if (next) { - /* couldn't put it back */ - dev_err(cs->dev, - "losing isoc write URB\n"); - error_hangup(bcs); - } - } - } - - /* process completed URB */ - urb = done->urb; - status = done->status; - switch (status) { - case -EXDEV: /* partial completion */ - gig_dbg(DEBUG_ISO, "%s: URB partially completed", - __func__); - /* fall through - what's the difference anyway? */ - case 0: /* normal completion */ - /* inspect individual frames - * assumptions (for lack of documentation): - * - actual_length bytes of first frame in error are - * successfully sent - * - all following frames are not sent at all - */ - for (i = 0; i < BAS_NUMFRAMES; i++) { - ifd = &urb->iso_frame_desc[i]; - if (ifd->status || - ifd->actual_length != ifd->length) { - dev_warn(cs->dev, - "isoc write: frame %d[%d/%d]: %s\n", - i, ifd->actual_length, - ifd->length, - get_usb_statmsg(ifd->status)); - break; - } - } - break; - case -EPIPE: /* stall - probably underrun */ - dev_err(cs->dev, "isoc write: stalled\n"); - error_hangup(bcs); - break; - default: /* other errors */ - dev_warn(cs->dev, "isoc write: %s\n", - get_usb_statmsg(status)); - } - - /* mark the write buffer area covered by this URB as free */ - if (done->limit >= 0) - ubc->isooutbuf->read = done->limit; - - /* mark URB as free */ - spin_lock_irqsave(&ubc->isooutlock, flags); - next = ubc->isooutfree; - ubc->isooutfree = done; - spin_unlock_irqrestore(&ubc->isooutlock, flags); - if (next) { - /* only one URB still active - resubmit one */ - rc = submit_iso_write_urb(next); - if (unlikely(rc <= 0 && rc != -ENODEV)) { - /* couldn't submit */ - error_hangup(bcs); - } - } - } - - /* process queued SKBs */ - while ((skb = skb_dequeue(&bcs->squeue))) { - /* copy to output buffer, doing L2 encapsulation */ - len = skb->len; - if (gigaset_isoc_buildframe(bcs, skb->data, len) == -EAGAIN) { - /* insufficient buffer space, push back onto queue */ - skb_queue_head(&bcs->squeue, skb); - gig_dbg(DEBUG_ISO, "%s: skb requeued, qlen=%d", - __func__, skb_queue_len(&bcs->squeue)); - break; - } - skb_pull(skb, len); - gigaset_skb_sent(bcs, skb); - dev_kfree_skb_any(skb); - } -} - -/* Isochronous Read - Bottom Half */ -/* ============================== */ - -/* read_iso_tasklet - * tasklet scheduled when an isochronous input URB from the Gigaset device - * has completed - * parameter: - * data B channel state structure - */ -static void read_iso_tasklet(unsigned long data) -{ - struct bc_state *bcs = (struct bc_state *) data; - struct bas_bc_state *ubc = bcs->hw.bas; - struct cardstate *cs = bcs->cs; - struct urb *urb; - int status; - struct usb_iso_packet_descriptor *ifd; - char *rcvbuf; - unsigned long flags; - int totleft, numbytes, offset, frame, rc; - - /* loop while more completed URBs arrive in the meantime */ - for (;;) { - /* retrieve URB */ - spin_lock_irqsave(&ubc->isoinlock, flags); - urb = ubc->isoindone; - if (!urb) { - spin_unlock_irqrestore(&ubc->isoinlock, flags); - return; - } - status = ubc->isoinstatus; - ubc->isoindone = NULL; - if (unlikely(ubc->loststatus != -EINPROGRESS)) { - dev_warn(cs->dev, - "isoc read overrun, URB dropped (status: %s, %d bytes)\n", - get_usb_statmsg(ubc->loststatus), - ubc->isoinlost); - ubc->loststatus = -EINPROGRESS; - } - spin_unlock_irqrestore(&ubc->isoinlock, flags); - - if (unlikely(!(ubc->running))) { - gig_dbg(DEBUG_ISO, - "%s: channel not running, " - "dropped URB with status: %s", - __func__, get_usb_statmsg(status)); - return; - } - - switch (status) { - case 0: /* normal completion */ - break; - case -EXDEV: /* inspect individual frames - (we do that anyway) */ - gig_dbg(DEBUG_ISO, "%s: URB partially completed", - __func__); - break; - case -ENOENT: - case -ECONNRESET: - case -EINPROGRESS: - gig_dbg(DEBUG_ISO, "%s: %s", - __func__, get_usb_statmsg(status)); - continue; /* -> skip */ - case -EPIPE: - dev_err(cs->dev, "isoc read: stalled\n"); - error_hangup(bcs); - continue; /* -> skip */ - default: /* other error */ - dev_warn(cs->dev, "isoc read: %s\n", - get_usb_statmsg(status)); - goto error; - } - - rcvbuf = urb->transfer_buffer; - totleft = urb->actual_length; - for (frame = 0; totleft > 0 && frame < BAS_NUMFRAMES; frame++) { - ifd = &urb->iso_frame_desc[frame]; - numbytes = ifd->actual_length; - switch (ifd->status) { - case 0: /* success */ - break; - case -EPROTO: /* protocol error or unplug */ - case -EILSEQ: - case -ETIME: - /* probably just disconnected, ignore */ - gig_dbg(DEBUG_ISO, - "isoc read: frame %d[%d]: %s\n", - frame, numbytes, - get_usb_statmsg(ifd->status)); - break; - default: /* other error */ - /* report, assume transferred bytes are ok */ - dev_warn(cs->dev, - "isoc read: frame %d[%d]: %s\n", - frame, numbytes, - get_usb_statmsg(ifd->status)); - } - if (unlikely(numbytes > BAS_MAXFRAME)) - dev_warn(cs->dev, - "isoc read: frame %d[%d]: %s\n", - frame, numbytes, - "exceeds max frame size"); - if (unlikely(numbytes > totleft)) { - dev_warn(cs->dev, - "isoc read: frame %d[%d]: %s\n", - frame, numbytes, - "exceeds total transfer length"); - numbytes = totleft; - } - offset = ifd->offset; - if (unlikely(offset + numbytes > BAS_INBUFSIZE)) { - dev_warn(cs->dev, - "isoc read: frame %d[%d]: %s\n", - frame, numbytes, - "exceeds end of buffer"); - numbytes = BAS_INBUFSIZE - offset; - } - gigaset_isoc_receive(rcvbuf + offset, numbytes, bcs); - totleft -= numbytes; - } - if (unlikely(totleft > 0)) - dev_warn(cs->dev, "isoc read: %d data bytes missing\n", - totleft); - -error: - /* URB processed, resubmit */ - for (frame = 0; frame < BAS_NUMFRAMES; frame++) { - urb->iso_frame_desc[frame].status = 0; - urb->iso_frame_desc[frame].actual_length = 0; - } - /* urb->dev is clobbered by USB subsystem */ - urb->dev = bcs->cs->hw.bas->udev; - urb->transfer_flags = URB_ISO_ASAP; - urb->number_of_packets = BAS_NUMFRAMES; - rc = usb_submit_urb(urb, GFP_ATOMIC); - if (unlikely(rc != 0 && rc != -ENODEV)) { - dev_err(cs->dev, - "could not resubmit isoc read URB: %s\n", - get_usb_rcmsg(rc)); - dump_urb(DEBUG_ISO, "resubmit isoc read", urb); - error_hangup(bcs); - } - } -} - -/* Channel Operations */ -/* ================== */ - -/* req_timeout - * timeout routine for control output request - * argument: - * controller state structure - */ -static void req_timeout(struct timer_list *t) -{ - struct bas_cardstate *ucs = from_timer(ucs, t, timer_ctrl); - struct cardstate *cs = ucs->cs; - int pending; - unsigned long flags; - - check_pending(ucs); - - spin_lock_irqsave(&ucs->lock, flags); - pending = ucs->pending; - ucs->pending = 0; - spin_unlock_irqrestore(&ucs->lock, flags); - - switch (pending) { - case 0: /* no pending request */ - gig_dbg(DEBUG_USBREQ, "%s: no request pending", __func__); - break; - - case HD_OPEN_ATCHANNEL: - dev_err(cs->dev, "timeout opening AT channel\n"); - error_reset(cs); - break; - - case HD_OPEN_B1CHANNEL: - dev_err(cs->dev, "timeout opening channel 1\n"); - error_hangup(&cs->bcs[0]); - break; - - case HD_OPEN_B2CHANNEL: - dev_err(cs->dev, "timeout opening channel 2\n"); - error_hangup(&cs->bcs[1]); - break; - - case HD_CLOSE_ATCHANNEL: - dev_err(cs->dev, "timeout closing AT channel\n"); - error_reset(cs); - break; - - case HD_CLOSE_B1CHANNEL: - dev_err(cs->dev, "timeout closing channel 1\n"); - error_reset(cs); - break; - - case HD_CLOSE_B2CHANNEL: - dev_err(cs->dev, "timeout closing channel 2\n"); - error_reset(cs); - break; - - case HD_RESET_INTERRUPT_PIPE: - /* error recovery escalation */ - dev_err(cs->dev, - "reset interrupt pipe timeout, attempting USB reset\n"); - usb_queue_reset_device(ucs->interface); - break; - - default: - dev_warn(cs->dev, "request 0x%02x timed out, clearing\n", - pending); - } - - wake_up(&ucs->waitqueue); -} - -/* write_ctrl_callback - * USB completion handler for control pipe output - * called by the USB subsystem in interrupt context - * parameter: - * urb USB request block of completed request - * urb->context = hardware specific controller state structure - */ -static void write_ctrl_callback(struct urb *urb) -{ - struct bas_cardstate *ucs = urb->context; - int status = urb->status; - int rc; - unsigned long flags; - - /* check status */ - switch (status) { - case 0: /* normal completion */ - spin_lock_irqsave(&ucs->lock, flags); - switch (ucs->pending) { - case HD_DEVICE_INIT_ACK: /* no reply expected */ - del_timer(&ucs->timer_ctrl); - ucs->pending = 0; - break; - } - spin_unlock_irqrestore(&ucs->lock, flags); - return; - - case -ENOENT: /* cancelled */ - case -ECONNRESET: /* cancelled (async) */ - case -EINPROGRESS: /* pending */ - case -ENODEV: /* device removed */ - case -ESHUTDOWN: /* device shut down */ - /* ignore silently */ - gig_dbg(DEBUG_USBREQ, "%s: %s", - __func__, get_usb_statmsg(status)); - break; - - default: /* any failure */ - /* don't retry if suspend requested */ - if (++ucs->retry_ctrl > BAS_RETRY || - (ucs->basstate & BS_SUSPEND)) { - dev_err(&ucs->interface->dev, - "control request 0x%02x failed: %s\n", - ucs->dr_ctrl.bRequest, - get_usb_statmsg(status)); - break; /* give up */ - } - dev_notice(&ucs->interface->dev, - "control request 0x%02x: %s, retry %d\n", - ucs->dr_ctrl.bRequest, get_usb_statmsg(status), - ucs->retry_ctrl); - /* urb->dev is clobbered by USB subsystem */ - urb->dev = ucs->udev; - rc = usb_submit_urb(urb, GFP_ATOMIC); - if (unlikely(rc)) { - dev_err(&ucs->interface->dev, - "could not resubmit request 0x%02x: %s\n", - ucs->dr_ctrl.bRequest, get_usb_rcmsg(rc)); - break; - } - /* resubmitted */ - return; - } - - /* failed, clear pending request */ - spin_lock_irqsave(&ucs->lock, flags); - del_timer(&ucs->timer_ctrl); - ucs->pending = 0; - spin_unlock_irqrestore(&ucs->lock, flags); - wake_up(&ucs->waitqueue); -} - -/* req_submit - * submit a control output request without message buffer to the Gigaset base - * and optionally start a timeout - * parameters: - * bcs B channel control structure - * req control request code (HD_*) - * val control request parameter value (set to 0 if unused) - * timeout timeout in seconds (0: no timeout) - * return value: - * 0 on success - * -EBUSY if another request is pending - * any URB submission error code - */ -static int req_submit(struct bc_state *bcs, int req, int val, int timeout) -{ - struct bas_cardstate *ucs = bcs->cs->hw.bas; - int ret; - unsigned long flags; - - gig_dbg(DEBUG_USBREQ, "-------> 0x%02x (%d)", req, val); - - spin_lock_irqsave(&ucs->lock, flags); - if (ucs->pending) { - spin_unlock_irqrestore(&ucs->lock, flags); - dev_err(bcs->cs->dev, - "submission of request 0x%02x failed: " - "request 0x%02x still pending\n", - req, ucs->pending); - return -EBUSY; - } - - ucs->dr_ctrl.bRequestType = OUT_VENDOR_REQ; - ucs->dr_ctrl.bRequest = req; - ucs->dr_ctrl.wValue = cpu_to_le16(val); - ucs->dr_ctrl.wIndex = 0; - ucs->dr_ctrl.wLength = 0; - usb_fill_control_urb(ucs->urb_ctrl, ucs->udev, - usb_sndctrlpipe(ucs->udev, 0), - (unsigned char *) &ucs->dr_ctrl, NULL, 0, - write_ctrl_callback, ucs); - ucs->retry_ctrl = 0; - ret = usb_submit_urb(ucs->urb_ctrl, GFP_ATOMIC); - if (unlikely(ret)) { - dev_err(bcs->cs->dev, "could not submit request 0x%02x: %s\n", - req, get_usb_rcmsg(ret)); - spin_unlock_irqrestore(&ucs->lock, flags); - return ret; - } - ucs->pending = req; - - if (timeout > 0) { - gig_dbg(DEBUG_USBREQ, "setting timeout of %d/10 secs", timeout); - mod_timer(&ucs->timer_ctrl, jiffies + timeout * HZ / 10); - } - - spin_unlock_irqrestore(&ucs->lock, flags); - return 0; -} - -/* gigaset_init_bchannel - * called by common.c to connect a B channel - * initialize isochronous I/O and tell the Gigaset base to open the channel - * argument: - * B channel control structure - * return value: - * 0 on success, error code < 0 on error - */ -static int gigaset_init_bchannel(struct bc_state *bcs) -{ - struct cardstate *cs = bcs->cs; - int req, ret; - unsigned long flags; - - spin_lock_irqsave(&cs->lock, flags); - if (unlikely(!cs->connected)) { - gig_dbg(DEBUG_USBREQ, "%s: not connected", __func__); - spin_unlock_irqrestore(&cs->lock, flags); - return -ENODEV; - } - - if (cs->hw.bas->basstate & BS_SUSPEND) { - dev_notice(cs->dev, - "not starting isoc I/O, suspend in progress\n"); - spin_unlock_irqrestore(&cs->lock, flags); - return -EHOSTUNREACH; - } - - ret = starturbs(bcs); - if (ret < 0) { - spin_unlock_irqrestore(&cs->lock, flags); - dev_err(cs->dev, - "could not start isoc I/O for channel B%d: %s\n", - bcs->channel + 1, - ret == -EFAULT ? "null URB" : get_usb_rcmsg(ret)); - if (ret != -ENODEV) - error_hangup(bcs); - return ret; - } - - req = bcs->channel ? HD_OPEN_B2CHANNEL : HD_OPEN_B1CHANNEL; - ret = req_submit(bcs, req, 0, BAS_TIMEOUT); - if (ret < 0) { - dev_err(cs->dev, "could not open channel B%d\n", - bcs->channel + 1); - stopurbs(bcs->hw.bas); - } - - spin_unlock_irqrestore(&cs->lock, flags); - if (ret < 0 && ret != -ENODEV) - error_hangup(bcs); - return ret; -} - -/* gigaset_close_bchannel - * called by common.c to disconnect a B channel - * tell the Gigaset base to close the channel - * stopping isochronous I/O and LL notification will be done when the - * acknowledgement for the close arrives - * argument: - * B channel control structure - * return value: - * 0 on success, error code < 0 on error - */ -static int gigaset_close_bchannel(struct bc_state *bcs) -{ - struct cardstate *cs = bcs->cs; - int req, ret; - unsigned long flags; - - spin_lock_irqsave(&cs->lock, flags); - if (unlikely(!cs->connected)) { - spin_unlock_irqrestore(&cs->lock, flags); - gig_dbg(DEBUG_USBREQ, "%s: not connected", __func__); - return -ENODEV; - } - - if (!(cs->hw.bas->basstate & (bcs->channel ? BS_B2OPEN : BS_B1OPEN))) { - /* channel not running: just signal common.c */ - spin_unlock_irqrestore(&cs->lock, flags); - gigaset_bchannel_down(bcs); - return 0; - } - - /* channel running: tell device to close it */ - req = bcs->channel ? HD_CLOSE_B2CHANNEL : HD_CLOSE_B1CHANNEL; - ret = req_submit(bcs, req, 0, BAS_TIMEOUT); - if (ret < 0) - dev_err(cs->dev, "closing channel B%d failed\n", - bcs->channel + 1); - - spin_unlock_irqrestore(&cs->lock, flags); - return ret; -} - -/* Device Operations */ -/* ================= */ - -/* complete_cb - * unqueue first command buffer from queue, waking any sleepers - * must be called with cs->cmdlock held - * parameter: - * cs controller state structure - */ -static void complete_cb(struct cardstate *cs) -{ - struct cmdbuf_t *cb = cs->cmdbuf; - - /* unqueue completed buffer */ - cs->cmdbytes -= cs->curlen; - gig_dbg(DEBUG_OUTPUT, "write_command: sent %u bytes, %u left", - cs->curlen, cs->cmdbytes); - if (cb->next != NULL) { - cs->cmdbuf = cb->next; - cs->cmdbuf->prev = NULL; - cs->curlen = cs->cmdbuf->len; - } else { - cs->cmdbuf = NULL; - cs->lastcmdbuf = NULL; - cs->curlen = 0; - } - - if (cb->wake_tasklet) - tasklet_schedule(cb->wake_tasklet); - - kfree(cb); -} - -/* write_command_callback - * USB completion handler for AT command transmission - * called by the USB subsystem in interrupt context - * parameter: - * urb USB request block of completed request - * urb->context = controller state structure - */ -static void write_command_callback(struct urb *urb) -{ - struct cardstate *cs = urb->context; - struct bas_cardstate *ucs = cs->hw.bas; - int status = urb->status; - unsigned long flags; - - update_basstate(ucs, 0, BS_ATWRPEND); - wake_up(&ucs->waitqueue); - - /* check status */ - switch (status) { - case 0: /* normal completion */ - break; - case -ENOENT: /* cancelled */ - case -ECONNRESET: /* cancelled (async) */ - case -EINPROGRESS: /* pending */ - case -ENODEV: /* device removed */ - case -ESHUTDOWN: /* device shut down */ - /* ignore silently */ - gig_dbg(DEBUG_USBREQ, "%s: %s", - __func__, get_usb_statmsg(status)); - return; - default: /* any failure */ - if (++ucs->retry_cmd_out > BAS_RETRY) { - dev_warn(cs->dev, - "command write: %s, " - "giving up after %d retries\n", - get_usb_statmsg(status), - ucs->retry_cmd_out); - break; - } - if (ucs->basstate & BS_SUSPEND) { - dev_warn(cs->dev, - "command write: %s, " - "won't retry - suspend requested\n", - get_usb_statmsg(status)); - break; - } - if (cs->cmdbuf == NULL) { - dev_warn(cs->dev, - "command write: %s, " - "cannot retry - cmdbuf gone\n", - get_usb_statmsg(status)); - break; - } - dev_notice(cs->dev, "command write: %s, retry %d\n", - get_usb_statmsg(status), ucs->retry_cmd_out); - if (atwrite_submit(cs, cs->cmdbuf->buf, cs->cmdbuf->len) >= 0) - /* resubmitted - bypass regular exit block */ - return; - /* command send failed, assume base still waiting */ - update_basstate(ucs, BS_ATREADY, 0); - } - - spin_lock_irqsave(&cs->cmdlock, flags); - if (cs->cmdbuf != NULL) - complete_cb(cs); - spin_unlock_irqrestore(&cs->cmdlock, flags); -} - -/* atrdy_timeout - * timeout routine for AT command transmission - * argument: - * controller state structure - */ -static void atrdy_timeout(struct timer_list *t) -{ - struct bas_cardstate *ucs = from_timer(ucs, t, timer_atrdy); - struct cardstate *cs = ucs->cs; - - dev_warn(cs->dev, "timeout waiting for HD_READY_SEND_ATDATA\n"); - - /* fake the missing signal - what else can I do? */ - update_basstate(ucs, BS_ATREADY, BS_ATTIMER); - start_cbsend(cs); -} - -/* atwrite_submit - * submit an HD_WRITE_ATMESSAGE command URB - * parameters: - * cs controller state structure - * buf buffer containing command to send - * len length of command to send - * return value: - * 0 on success - * -EBUSY if another request is pending - * any URB submission error code - */ -static int atwrite_submit(struct cardstate *cs, unsigned char *buf, int len) -{ - struct bas_cardstate *ucs = cs->hw.bas; - int rc; - - gig_dbg(DEBUG_USBREQ, "-------> HD_WRITE_ATMESSAGE (%d)", len); - - if (update_basstate(ucs, BS_ATWRPEND, 0) & BS_ATWRPEND) { - dev_err(cs->dev, - "could not submit HD_WRITE_ATMESSAGE: URB busy\n"); - return -EBUSY; - } - - ucs->dr_cmd_out.bRequestType = OUT_VENDOR_REQ; - ucs->dr_cmd_out.bRequest = HD_WRITE_ATMESSAGE; - ucs->dr_cmd_out.wValue = 0; - ucs->dr_cmd_out.wIndex = 0; - ucs->dr_cmd_out.wLength = cpu_to_le16(len); - usb_fill_control_urb(ucs->urb_cmd_out, ucs->udev, - usb_sndctrlpipe(ucs->udev, 0), - (unsigned char *) &ucs->dr_cmd_out, buf, len, - write_command_callback, cs); - rc = usb_submit_urb(ucs->urb_cmd_out, GFP_ATOMIC); - if (unlikely(rc)) { - update_basstate(ucs, 0, BS_ATWRPEND); - dev_err(cs->dev, "could not submit HD_WRITE_ATMESSAGE: %s\n", - get_usb_rcmsg(rc)); - return rc; - } - - /* submitted successfully, start timeout if necessary */ - if (!(update_basstate(ucs, BS_ATTIMER, BS_ATREADY) & BS_ATTIMER)) { - gig_dbg(DEBUG_OUTPUT, "setting ATREADY timeout of %d/10 secs", - ATRDY_TIMEOUT); - mod_timer(&ucs->timer_atrdy, jiffies + ATRDY_TIMEOUT * HZ / 10); - } - return 0; -} - -/* start_cbsend - * start transmission of AT command queue if necessary - * parameter: - * cs controller state structure - * return value: - * 0 on success - * error code < 0 on error - */ -static int start_cbsend(struct cardstate *cs) -{ - struct cmdbuf_t *cb; - struct bas_cardstate *ucs = cs->hw.bas; - unsigned long flags; - int rc; - int retval = 0; - - /* check if suspend requested */ - if (ucs->basstate & BS_SUSPEND) { - gig_dbg(DEBUG_OUTPUT, "suspending"); - return -EHOSTUNREACH; - } - - /* check if AT channel is open */ - if (!(ucs->basstate & BS_ATOPEN)) { - gig_dbg(DEBUG_OUTPUT, "AT channel not open"); - rc = req_submit(cs->bcs, HD_OPEN_ATCHANNEL, 0, BAS_TIMEOUT); - if (rc < 0) { - /* flush command queue */ - spin_lock_irqsave(&cs->cmdlock, flags); - while (cs->cmdbuf != NULL) - complete_cb(cs); - spin_unlock_irqrestore(&cs->cmdlock, flags); - } - return rc; - } - - /* try to send first command in queue */ - spin_lock_irqsave(&cs->cmdlock, flags); - - while ((cb = cs->cmdbuf) != NULL && (ucs->basstate & BS_ATREADY)) { - ucs->retry_cmd_out = 0; - rc = atwrite_submit(cs, cb->buf, cb->len); - if (unlikely(rc)) { - retval = rc; - complete_cb(cs); - } - } - - spin_unlock_irqrestore(&cs->cmdlock, flags); - return retval; -} - -/* gigaset_write_cmd - * This function is called by the device independent part of the driver - * to transmit an AT command string to the Gigaset device. - * It encapsulates the device specific method for transmission over the - * direct USB connection to the base. - * The command string is added to the queue of commands to send, and - * USB transmission is started if necessary. - * parameters: - * cs controller state structure - * cb command buffer structure - * return value: - * number of bytes queued on success - * error code < 0 on error - */ -static int gigaset_write_cmd(struct cardstate *cs, struct cmdbuf_t *cb) -{ - unsigned long flags; - int rc; - - gigaset_dbg_buffer(cs->mstate != MS_LOCKED ? - DEBUG_TRANSCMD : DEBUG_LOCKCMD, - "CMD Transmit", cb->len, cb->buf); - - /* translate "+++" escape sequence sent as a single separate command - * into "close AT channel" command for error recovery - * The next command will reopen the AT channel automatically. - */ - if (cb->len == 3 && !memcmp(cb->buf, "+++", 3)) { - /* If an HD_RECEIVEATDATA_ACK message remains unhandled - * because of an error, the base never sends another one. - * The response channel is thus effectively blocked. - * Closing and reopening the AT channel does *not* clear - * this condition. - * As a stopgap measure, submit a zero-length AT read - * before closing the AT channel. This has the undocumented - * effect of triggering a new HD_RECEIVEATDATA_ACK message - * from the base if necessary. - * The subsequent AT channel close then discards any pending - * messages. - */ - spin_lock_irqsave(&cs->lock, flags); - if (!(cs->hw.bas->basstate & BS_ATRDPEND)) { - kfree(cs->hw.bas->rcvbuf); - cs->hw.bas->rcvbuf = NULL; - cs->hw.bas->rcvbuf_size = 0; - cs->hw.bas->retry_cmd_in = 0; - atread_submit(cs, 0); - } - spin_unlock_irqrestore(&cs->lock, flags); - - rc = req_submit(cs->bcs, HD_CLOSE_ATCHANNEL, 0, BAS_TIMEOUT); - if (cb->wake_tasklet) - tasklet_schedule(cb->wake_tasklet); - if (!rc) - rc = cb->len; - kfree(cb); - return rc; - } - - spin_lock_irqsave(&cs->cmdlock, flags); - cb->prev = cs->lastcmdbuf; - if (cs->lastcmdbuf) - cs->lastcmdbuf->next = cb; - else { - cs->cmdbuf = cb; - cs->curlen = cb->len; - } - cs->cmdbytes += cb->len; - cs->lastcmdbuf = cb; - spin_unlock_irqrestore(&cs->cmdlock, flags); - - spin_lock_irqsave(&cs->lock, flags); - if (unlikely(!cs->connected)) { - spin_unlock_irqrestore(&cs->lock, flags); - gig_dbg(DEBUG_USBREQ, "%s: not connected", __func__); - /* flush command queue */ - spin_lock_irqsave(&cs->cmdlock, flags); - while (cs->cmdbuf != NULL) - complete_cb(cs); - spin_unlock_irqrestore(&cs->cmdlock, flags); - return -ENODEV; - } - rc = start_cbsend(cs); - spin_unlock_irqrestore(&cs->lock, flags); - return rc < 0 ? rc : cb->len; -} - -/* gigaset_write_room - * tty_driver.write_room interface routine - * return number of characters the driver will accept to be written via - * gigaset_write_cmd - * parameter: - * controller state structure - * return value: - * number of characters - */ -static int gigaset_write_room(struct cardstate *cs) -{ - return IF_WRITEBUF; -} - -/* gigaset_chars_in_buffer - * tty_driver.chars_in_buffer interface routine - * return number of characters waiting to be sent - * parameter: - * controller state structure - * return value: - * number of characters - */ -static int gigaset_chars_in_buffer(struct cardstate *cs) -{ - return cs->cmdbytes; -} - -/* gigaset_brkchars - * implementation of ioctl(GIGASET_BRKCHARS) - * parameter: - * controller state structure - * return value: - * -EINVAL (unimplemented function) - */ -static int gigaset_brkchars(struct cardstate *cs, const unsigned char buf[6]) -{ - return -EINVAL; -} - - -/* Device Initialization/Shutdown */ -/* ============================== */ - -/* Free hardware dependent part of the B channel structure - * parameter: - * bcs B channel structure - */ -static void gigaset_freebcshw(struct bc_state *bcs) -{ - struct bas_bc_state *ubc = bcs->hw.bas; - int i; - - if (!ubc) - return; - - /* kill URBs and tasklets before freeing - better safe than sorry */ - ubc->running = 0; - gig_dbg(DEBUG_INIT, "%s: killing isoc URBs", __func__); - for (i = 0; i < BAS_OUTURBS; ++i) { - usb_kill_urb(ubc->isoouturbs[i].urb); - usb_free_urb(ubc->isoouturbs[i].urb); - } - for (i = 0; i < BAS_INURBS; ++i) { - usb_kill_urb(ubc->isoinurbs[i]); - usb_free_urb(ubc->isoinurbs[i]); - } - tasklet_kill(&ubc->sent_tasklet); - tasklet_kill(&ubc->rcvd_tasklet); - kfree(ubc->isooutbuf); - kfree(ubc); - bcs->hw.bas = NULL; -} - -/* Initialize hardware dependent part of the B channel structure - * parameter: - * bcs B channel structure - * return value: - * 0 on success, error code < 0 on failure - */ -static int gigaset_initbcshw(struct bc_state *bcs) -{ - int i; - struct bas_bc_state *ubc; - - bcs->hw.bas = ubc = kmalloc(sizeof(struct bas_bc_state), GFP_KERNEL); - if (!ubc) { - pr_err("out of memory\n"); - return -ENOMEM; - } - - ubc->running = 0; - atomic_set(&ubc->corrbytes, 0); - spin_lock_init(&ubc->isooutlock); - for (i = 0; i < BAS_OUTURBS; ++i) { - ubc->isoouturbs[i].urb = NULL; - ubc->isoouturbs[i].bcs = bcs; - } - ubc->isooutdone = ubc->isooutfree = ubc->isooutovfl = NULL; - ubc->numsub = 0; - ubc->isooutbuf = kmalloc(sizeof(struct isowbuf_t), GFP_KERNEL); - if (!ubc->isooutbuf) { - pr_err("out of memory\n"); - kfree(ubc); - bcs->hw.bas = NULL; - return -ENOMEM; - } - tasklet_init(&ubc->sent_tasklet, - write_iso_tasklet, (unsigned long) bcs); - - spin_lock_init(&ubc->isoinlock); - for (i = 0; i < BAS_INURBS; ++i) - ubc->isoinurbs[i] = NULL; - ubc->isoindone = NULL; - ubc->loststatus = -EINPROGRESS; - ubc->isoinlost = 0; - ubc->seqlen = 0; - ubc->inbyte = 0; - ubc->inbits = 0; - ubc->goodbytes = 0; - ubc->alignerrs = 0; - ubc->fcserrs = 0; - ubc->frameerrs = 0; - ubc->giants = 0; - ubc->runts = 0; - ubc->aborts = 0; - ubc->shared0s = 0; - ubc->stolen0s = 0; - tasklet_init(&ubc->rcvd_tasklet, - read_iso_tasklet, (unsigned long) bcs); - return 0; -} - -static void gigaset_reinitbcshw(struct bc_state *bcs) -{ - struct bas_bc_state *ubc = bcs->hw.bas; - - bcs->hw.bas->running = 0; - atomic_set(&bcs->hw.bas->corrbytes, 0); - bcs->hw.bas->numsub = 0; - spin_lock_init(&ubc->isooutlock); - spin_lock_init(&ubc->isoinlock); - ubc->loststatus = -EINPROGRESS; -} - -static void gigaset_freecshw(struct cardstate *cs) -{ - /* timers, URBs and rcvbuf are disposed of in disconnect */ - kfree(cs->hw.bas->int_in_buf); - kfree(cs->hw.bas); - cs->hw.bas = NULL; -} - -/* Initialize hardware dependent part of the cardstate structure - * parameter: - * cs cardstate structure - * return value: - * 0 on success, error code < 0 on failure - */ -static int gigaset_initcshw(struct cardstate *cs) -{ - struct bas_cardstate *ucs; - - cs->hw.bas = ucs = kzalloc(sizeof(*ucs), GFP_KERNEL); - if (!ucs) { - pr_err("out of memory\n"); - return -ENOMEM; - } - ucs->int_in_buf = kmalloc(IP_MSGSIZE, GFP_KERNEL); - if (!ucs->int_in_buf) { - kfree(ucs); - pr_err("out of memory\n"); - return -ENOMEM; - } - - spin_lock_init(&ucs->lock); - ucs->cs = cs; - timer_setup(&ucs->timer_ctrl, req_timeout, 0); - timer_setup(&ucs->timer_atrdy, atrdy_timeout, 0); - timer_setup(&ucs->timer_cmd_in, cmd_in_timeout, 0); - timer_setup(&ucs->timer_int_in, int_in_resubmit, 0); - init_waitqueue_head(&ucs->waitqueue); - INIT_WORK(&ucs->int_in_wq, int_in_work); - - return 0; -} - -/* freeurbs - * unlink and deallocate all URBs unconditionally - * caller must make sure that no commands are still in progress - * parameter: - * cs controller state structure - */ -static void freeurbs(struct cardstate *cs) -{ - struct bas_cardstate *ucs = cs->hw.bas; - struct bas_bc_state *ubc; - int i, j; - - gig_dbg(DEBUG_INIT, "%s: killing URBs", __func__); - for (j = 0; j < BAS_CHANNELS; ++j) { - ubc = cs->bcs[j].hw.bas; - for (i = 0; i < BAS_OUTURBS; ++i) { - usb_kill_urb(ubc->isoouturbs[i].urb); - usb_free_urb(ubc->isoouturbs[i].urb); - ubc->isoouturbs[i].urb = NULL; - } - for (i = 0; i < BAS_INURBS; ++i) { - usb_kill_urb(ubc->isoinurbs[i]); - usb_free_urb(ubc->isoinurbs[i]); - ubc->isoinurbs[i] = NULL; - } - } - usb_kill_urb(ucs->urb_int_in); - usb_free_urb(ucs->urb_int_in); - ucs->urb_int_in = NULL; - usb_kill_urb(ucs->urb_cmd_out); - usb_free_urb(ucs->urb_cmd_out); - ucs->urb_cmd_out = NULL; - usb_kill_urb(ucs->urb_cmd_in); - usb_free_urb(ucs->urb_cmd_in); - ucs->urb_cmd_in = NULL; - usb_kill_urb(ucs->urb_ctrl); - usb_free_urb(ucs->urb_ctrl); - ucs->urb_ctrl = NULL; -} - -/* gigaset_probe - * This function is called when a new USB device is connected. - * It checks whether the new device is handled by this driver. - */ -static int gigaset_probe(struct usb_interface *interface, - const struct usb_device_id *id) -{ - struct usb_host_interface *hostif; - struct usb_device *udev = interface_to_usbdev(interface); - struct cardstate *cs = NULL; - struct bas_cardstate *ucs = NULL; - struct bas_bc_state *ubc; - struct usb_endpoint_descriptor *endpoint; - int i, j; - int rc; - - gig_dbg(DEBUG_INIT, - "%s: Check if device matches .. (Vendor: 0x%x, Product: 0x%x)", - __func__, le16_to_cpu(udev->descriptor.idVendor), - le16_to_cpu(udev->descriptor.idProduct)); - - /* set required alternate setting */ - hostif = interface->cur_altsetting; - if (hostif->desc.bAlternateSetting != 3) { - gig_dbg(DEBUG_INIT, - "%s: wrong alternate setting %d - trying to switch", - __func__, hostif->desc.bAlternateSetting); - if (usb_set_interface(udev, hostif->desc.bInterfaceNumber, 3) - < 0) { - dev_warn(&udev->dev, "usb_set_interface failed, " - "device %d interface %d altsetting %d\n", - udev->devnum, hostif->desc.bInterfaceNumber, - hostif->desc.bAlternateSetting); - return -ENODEV; - } - hostif = interface->cur_altsetting; - } - - /* Reject application specific interfaces - */ - if (hostif->desc.bInterfaceClass != 255) { - dev_warn(&udev->dev, "%s: bInterfaceClass == %d\n", - __func__, hostif->desc.bInterfaceClass); - return -ENODEV; - } - - if (hostif->desc.bNumEndpoints < 1) - return -ENODEV; - - dev_info(&udev->dev, - "%s: Device matched (Vendor: 0x%x, Product: 0x%x)\n", - __func__, le16_to_cpu(udev->descriptor.idVendor), - le16_to_cpu(udev->descriptor.idProduct)); - - /* allocate memory for our device state and initialize it */ - cs = gigaset_initcs(driver, BAS_CHANNELS, 0, 0, cidmode, - GIGASET_MODULENAME); - if (!cs) - return -ENODEV; - ucs = cs->hw.bas; - - /* save off device structure ptrs for later use */ - usb_get_dev(udev); - ucs->udev = udev; - ucs->interface = interface; - cs->dev = &interface->dev; - - /* allocate URBs: - * - one for the interrupt pipe - * - three for the different uses of the default control pipe - * - three for each isochronous pipe - */ - if (!(ucs->urb_int_in = usb_alloc_urb(0, GFP_KERNEL)) || - !(ucs->urb_cmd_in = usb_alloc_urb(0, GFP_KERNEL)) || - !(ucs->urb_cmd_out = usb_alloc_urb(0, GFP_KERNEL)) || - !(ucs->urb_ctrl = usb_alloc_urb(0, GFP_KERNEL))) - goto allocerr; - - for (j = 0; j < BAS_CHANNELS; ++j) { - ubc = cs->bcs[j].hw.bas; - for (i = 0; i < BAS_OUTURBS; ++i) - if (!(ubc->isoouturbs[i].urb = - usb_alloc_urb(BAS_NUMFRAMES, GFP_KERNEL))) - goto allocerr; - for (i = 0; i < BAS_INURBS; ++i) - if (!(ubc->isoinurbs[i] = - usb_alloc_urb(BAS_NUMFRAMES, GFP_KERNEL))) - goto allocerr; - } - - ucs->rcvbuf = NULL; - ucs->rcvbuf_size = 0; - - /* Fill the interrupt urb and send it to the core */ - endpoint = &hostif->endpoint[0].desc; - usb_fill_int_urb(ucs->urb_int_in, udev, - usb_rcvintpipe(udev, - usb_endpoint_num(endpoint)), - ucs->int_in_buf, IP_MSGSIZE, read_int_callback, cs, - endpoint->bInterval); - rc = usb_submit_urb(ucs->urb_int_in, GFP_KERNEL); - if (rc != 0) { - dev_err(cs->dev, "could not submit interrupt URB: %s\n", - get_usb_rcmsg(rc)); - goto error; - } - ucs->retry_int_in = 0; - - /* tell the device that the driver is ready */ - rc = req_submit(cs->bcs, HD_DEVICE_INIT_ACK, 0, 0); - if (rc != 0) - goto error; - - /* tell common part that the device is ready */ - if (startmode == SM_LOCKED) - cs->mstate = MS_LOCKED; - - /* save address of controller structure */ - usb_set_intfdata(interface, cs); - - rc = gigaset_start(cs); - if (rc < 0) - goto error; - - return 0; - -allocerr: - dev_err(cs->dev, "could not allocate URBs\n"); - rc = -ENOMEM; -error: - freeurbs(cs); - usb_set_intfdata(interface, NULL); - usb_put_dev(udev); - gigaset_freecs(cs); - return rc; -} - -/* gigaset_disconnect - * This function is called when the Gigaset base is unplugged. - */ -static void gigaset_disconnect(struct usb_interface *interface) -{ - struct cardstate *cs; - struct bas_cardstate *ucs; - int j; - - cs = usb_get_intfdata(interface); - - ucs = cs->hw.bas; - - dev_info(cs->dev, "disconnecting Gigaset base\n"); - - /* mark base as not ready, all channels disconnected */ - ucs->basstate = 0; - - /* tell LL all channels are down */ - for (j = 0; j < BAS_CHANNELS; ++j) - gigaset_bchannel_down(cs->bcs + j); - - /* stop driver (common part) */ - gigaset_stop(cs); - - /* stop delayed work and URBs, free ressources */ - del_timer_sync(&ucs->timer_ctrl); - del_timer_sync(&ucs->timer_atrdy); - del_timer_sync(&ucs->timer_cmd_in); - del_timer_sync(&ucs->timer_int_in); - cancel_work_sync(&ucs->int_in_wq); - freeurbs(cs); - usb_set_intfdata(interface, NULL); - kfree(ucs->rcvbuf); - ucs->rcvbuf = NULL; - ucs->rcvbuf_size = 0; - usb_put_dev(ucs->udev); - ucs->interface = NULL; - ucs->udev = NULL; - cs->dev = NULL; - gigaset_freecs(cs); -} - -/* gigaset_suspend - * This function is called before the USB connection is suspended - * or before the USB device is reset. - * In the latter case, message == PMSG_ON. - */ -static int gigaset_suspend(struct usb_interface *intf, pm_message_t message) -{ - struct cardstate *cs = usb_get_intfdata(intf); - struct bas_cardstate *ucs = cs->hw.bas; - int rc; - - /* set suspend flag; this stops AT command/response traffic */ - if (update_basstate(ucs, BS_SUSPEND, 0) & BS_SUSPEND) { - gig_dbg(DEBUG_SUSPEND, "already suspended"); - return 0; - } - - /* wait a bit for blocking conditions to go away */ - rc = wait_event_timeout(ucs->waitqueue, - !(ucs->basstate & - (BS_B1OPEN | BS_B2OPEN | BS_ATRDPEND | BS_ATWRPEND)), - BAS_TIMEOUT * HZ / 10); - gig_dbg(DEBUG_SUSPEND, "wait_event_timeout() -> %d", rc); - - /* check for conditions preventing suspend */ - if (ucs->basstate & (BS_B1OPEN | BS_B2OPEN | BS_ATRDPEND | BS_ATWRPEND)) { - dev_warn(cs->dev, "cannot suspend:\n"); - if (ucs->basstate & BS_B1OPEN) - dev_warn(cs->dev, " B channel 1 open\n"); - if (ucs->basstate & BS_B2OPEN) - dev_warn(cs->dev, " B channel 2 open\n"); - if (ucs->basstate & BS_ATRDPEND) - dev_warn(cs->dev, " receiving AT reply\n"); - if (ucs->basstate & BS_ATWRPEND) - dev_warn(cs->dev, " sending AT command\n"); - update_basstate(ucs, 0, BS_SUSPEND); - return -EBUSY; - } - - /* close AT channel if open */ - if (ucs->basstate & BS_ATOPEN) { - gig_dbg(DEBUG_SUSPEND, "closing AT channel"); - rc = req_submit(cs->bcs, HD_CLOSE_ATCHANNEL, 0, 0); - if (rc) { - update_basstate(ucs, 0, BS_SUSPEND); - return rc; - } - wait_event_timeout(ucs->waitqueue, !ucs->pending, - BAS_TIMEOUT * HZ / 10); - /* in case of timeout, proceed anyway */ - } - - /* kill all URBs and delayed work that might still be pending */ - usb_kill_urb(ucs->urb_ctrl); - usb_kill_urb(ucs->urb_int_in); - del_timer_sync(&ucs->timer_ctrl); - del_timer_sync(&ucs->timer_atrdy); - del_timer_sync(&ucs->timer_cmd_in); - del_timer_sync(&ucs->timer_int_in); - - /* don't try to cancel int_in_wq from within reset as it - * might be the one requesting the reset - */ - if (message.event != PM_EVENT_ON) - cancel_work_sync(&ucs->int_in_wq); - - gig_dbg(DEBUG_SUSPEND, "suspend complete"); - return 0; -} - -/* gigaset_resume - * This function is called after the USB connection has been resumed. - */ -static int gigaset_resume(struct usb_interface *intf) -{ - struct cardstate *cs = usb_get_intfdata(intf); - struct bas_cardstate *ucs = cs->hw.bas; - int rc; - - /* resubmit interrupt URB for spontaneous messages from base */ - rc = usb_submit_urb(ucs->urb_int_in, GFP_KERNEL); - if (rc) { - dev_err(cs->dev, "could not resubmit interrupt URB: %s\n", - get_usb_rcmsg(rc)); - return rc; - } - ucs->retry_int_in = 0; - - /* clear suspend flag to reallow activity */ - update_basstate(ucs, 0, BS_SUSPEND); - - gig_dbg(DEBUG_SUSPEND, "resume complete"); - return 0; -} - -/* gigaset_pre_reset - * This function is called before the USB connection is reset. - */ -static int gigaset_pre_reset(struct usb_interface *intf) -{ - /* handle just like suspend */ - return gigaset_suspend(intf, PMSG_ON); -} - -/* gigaset_post_reset - * This function is called after the USB connection has been reset. - */ -static int gigaset_post_reset(struct usb_interface *intf) -{ - /* FIXME: send HD_DEVICE_INIT_ACK? */ - - /* resume operations */ - return gigaset_resume(intf); -} - - -static const struct gigaset_ops gigops = { - .write_cmd = gigaset_write_cmd, - .write_room = gigaset_write_room, - .chars_in_buffer = gigaset_chars_in_buffer, - .brkchars = gigaset_brkchars, - .init_bchannel = gigaset_init_bchannel, - .close_bchannel = gigaset_close_bchannel, - .initbcshw = gigaset_initbcshw, - .freebcshw = gigaset_freebcshw, - .reinitbcshw = gigaset_reinitbcshw, - .initcshw = gigaset_initcshw, - .freecshw = gigaset_freecshw, - .set_modem_ctrl = gigaset_set_modem_ctrl, - .baud_rate = gigaset_baud_rate, - .set_line_ctrl = gigaset_set_line_ctrl, - .send_skb = gigaset_isoc_send_skb, - .handle_input = gigaset_isoc_input, -}; - -/* bas_gigaset_init - * This function is called after the kernel module is loaded. - */ -static int __init bas_gigaset_init(void) -{ - int result; - - /* allocate memory for our driver state and initialize it */ - driver = gigaset_initdriver(GIGASET_MINOR, GIGASET_MINORS, - GIGASET_MODULENAME, GIGASET_DEVNAME, - &gigops, THIS_MODULE); - if (driver == NULL) - goto error; - - /* register this driver with the USB subsystem */ - result = usb_register(&gigaset_usb_driver); - if (result < 0) { - pr_err("error %d registering USB driver\n", -result); - goto error; - } - - pr_info(DRIVER_DESC "\n"); - return 0; - -error: - if (driver) - gigaset_freedriver(driver); - driver = NULL; - return -1; -} - -/* bas_gigaset_exit - * This function is called before the kernel module is unloaded. - */ -static void __exit bas_gigaset_exit(void) -{ - struct bas_cardstate *ucs; - int i; - - gigaset_blockdriver(driver); /* => probe will fail - * => no gigaset_start any more - */ - - /* stop all connected devices */ - for (i = 0; i < driver->minors; i++) { - if (gigaset_shutdown(driver->cs + i) < 0) - continue; /* no device */ - /* from now on, no isdn callback should be possible */ - - /* close all still open channels */ - ucs = driver->cs[i].hw.bas; - if (ucs->basstate & BS_B1OPEN) { - gig_dbg(DEBUG_INIT, "closing B1 channel"); - usb_control_msg(ucs->udev, - usb_sndctrlpipe(ucs->udev, 0), - HD_CLOSE_B1CHANNEL, OUT_VENDOR_REQ, - 0, 0, NULL, 0, BAS_TIMEOUT); - } - if (ucs->basstate & BS_B2OPEN) { - gig_dbg(DEBUG_INIT, "closing B2 channel"); - usb_control_msg(ucs->udev, - usb_sndctrlpipe(ucs->udev, 0), - HD_CLOSE_B2CHANNEL, OUT_VENDOR_REQ, - 0, 0, NULL, 0, BAS_TIMEOUT); - } - if (ucs->basstate & BS_ATOPEN) { - gig_dbg(DEBUG_INIT, "closing AT channel"); - usb_control_msg(ucs->udev, - usb_sndctrlpipe(ucs->udev, 0), - HD_CLOSE_ATCHANNEL, OUT_VENDOR_REQ, - 0, 0, NULL, 0, BAS_TIMEOUT); - } - ucs->basstate = 0; - } - - /* deregister this driver with the USB subsystem */ - usb_deregister(&gigaset_usb_driver); - /* this will call the disconnect-callback */ - /* from now on, no disconnect/probe callback should be running */ - - gigaset_freedriver(driver); - driver = NULL; -} - - -module_init(bas_gigaset_init); -module_exit(bas_gigaset_exit); - -MODULE_AUTHOR(DRIVER_AUTHOR); -MODULE_DESCRIPTION(DRIVER_DESC); -MODULE_LICENSE("GPL"); diff --git a/drivers/staging/isdn/gigaset/capi.c b/drivers/staging/isdn/gigaset/capi.c deleted file mode 100644 index 83d7dd48c61d..000000000000 --- a/drivers/staging/isdn/gigaset/capi.c +++ /dev/null @@ -1,2517 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -/* - * Kernel CAPI interface for the Gigaset driver - * - * Copyright (c) 2009 by Tilman Schmidt <tilman@imap.cc>. - * - * ===================================================================== - * ===================================================================== - */ - -#include "gigaset.h" -#include <linux/proc_fs.h> -#include <linux/seq_file.h> -#include <linux/ratelimit.h> -#include <linux/isdn/capilli.h> -#include <linux/isdn/capicmd.h> -#include <linux/isdn/capiutil.h> -#include <linux/export.h> - -/* missing from kernelcapi.h */ -#define CapiNcpiNotSupportedByProtocol 0x0001 -#define CapiFlagsNotSupportedByProtocol 0x0002 -#define CapiAlertAlreadySent 0x0003 -#define CapiFacilitySpecificFunctionNotSupported 0x3011 - -/* missing from capicmd.h */ -#define CAPI_CONNECT_IND_BASELEN (CAPI_MSG_BASELEN + 4 + 2 + 8 * 1) -#define CAPI_CONNECT_ACTIVE_IND_BASELEN (CAPI_MSG_BASELEN + 4 + 3 * 1) -#define CAPI_CONNECT_B3_IND_BASELEN (CAPI_MSG_BASELEN + 4 + 1) -#define CAPI_CONNECT_B3_ACTIVE_IND_BASELEN (CAPI_MSG_BASELEN + 4 + 1) -#define CAPI_DATA_B3_REQ_LEN64 (CAPI_MSG_BASELEN + 4 + 4 + 2 + 2 + 2 + 8) -#define CAPI_DATA_B3_CONF_LEN (CAPI_MSG_BASELEN + 4 + 2 + 2) -#define CAPI_DISCONNECT_IND_LEN (CAPI_MSG_BASELEN + 4 + 2) -#define CAPI_DISCONNECT_B3_IND_BASELEN (CAPI_MSG_BASELEN + 4 + 2 + 1) -#define CAPI_FACILITY_CONF_BASELEN (CAPI_MSG_BASELEN + 4 + 2 + 2 + 1) -/* most _CONF messages contain only Controller/PLCI/NCCI and Info parameters */ -#define CAPI_STDCONF_LEN (CAPI_MSG_BASELEN + 4 + 2) - -#define CAPI_FACILITY_HANDSET 0x0000 -#define CAPI_FACILITY_DTMF 0x0001 -#define CAPI_FACILITY_V42BIS 0x0002 -#define CAPI_FACILITY_SUPPSVC 0x0003 -#define CAPI_FACILITY_WAKEUP 0x0004 -#define CAPI_FACILITY_LI 0x0005 - -#define CAPI_SUPPSVC_GETSUPPORTED 0x0000 -#define CAPI_SUPPSVC_LISTEN 0x0001 - -/* missing from capiutil.h */ -#define CAPIMSG_PLCI_PART(m) CAPIMSG_U8(m, 9) -#define CAPIMSG_NCCI_PART(m) CAPIMSG_U16(m, 10) -#define CAPIMSG_HANDLE_REQ(m) CAPIMSG_U16(m, 18) /* DATA_B3_REQ/_IND only! */ -#define CAPIMSG_FLAGS(m) CAPIMSG_U16(m, 20) -#define CAPIMSG_SETCONTROLLER(m, contr) capimsg_setu8(m, 8, contr) -#define CAPIMSG_SETPLCI_PART(m, plci) capimsg_setu8(m, 9, plci) -#define CAPIMSG_SETNCCI_PART(m, ncci) capimsg_setu16(m, 10, ncci) -#define CAPIMSG_SETFLAGS(m, flags) capimsg_setu16(m, 20, flags) - -/* parameters with differing location in DATA_B3_CONF/_RESP: */ -#define CAPIMSG_SETHANDLE_CONF(m, handle) capimsg_setu16(m, 12, handle) -#define CAPIMSG_SETINFO_CONF(m, info) capimsg_setu16(m, 14, info) - -/* Flags (DATA_B3_REQ/_IND) */ -#define CAPI_FLAGS_DELIVERY_CONFIRMATION 0x04 -#define CAPI_FLAGS_RESERVED (~0x1f) - -/* buffer sizes */ -#define MAX_BC_OCTETS 11 -#define MAX_HLC_OCTETS 3 -#define MAX_NUMBER_DIGITS 20 -#define MAX_FMT_IE_LEN 20 - -/* values for bcs->apconnstate */ -#define APCONN_NONE 0 /* inactive/listening */ -#define APCONN_SETUP 1 /* connecting */ -#define APCONN_ACTIVE 2 /* B channel up */ - -/* registered application data structure */ -struct gigaset_capi_appl { - struct list_head ctrlist; - struct gigaset_capi_appl *bcnext; - u16 id; - struct capi_register_params rp; - u16 nextMessageNumber; - u32 listenInfoMask; - u32 listenCIPmask; -}; - -/* CAPI specific controller data structure */ -struct gigaset_capi_ctr { - struct capi_ctr ctr; - struct list_head appls; - struct sk_buff_head sendqueue; - atomic_t sendqlen; - /* two _cmsg structures possibly used concurrently: */ - _cmsg hcmsg; /* for message composition triggered from hardware */ - _cmsg acmsg; /* for dissection of messages sent from application */ - u8 bc_buf[MAX_BC_OCTETS + 1]; - u8 hlc_buf[MAX_HLC_OCTETS + 1]; - u8 cgpty_buf[MAX_NUMBER_DIGITS + 3]; - u8 cdpty_buf[MAX_NUMBER_DIGITS + 2]; -}; - -/* CIP Value table (from CAPI 2.0 standard, ch. 6.1) */ -static struct { - u8 *bc; - u8 *hlc; -} cip2bchlc[] = { - [1] = { "8090A3", NULL }, /* Speech (A-law) */ - [2] = { "8890", NULL }, /* Unrestricted digital information */ - [3] = { "8990", NULL }, /* Restricted digital information */ - [4] = { "9090A3", NULL }, /* 3,1 kHz audio (A-law) */ - [5] = { "9190", NULL }, /* 7 kHz audio */ - [6] = { "9890", NULL }, /* Video */ - [7] = { "88C0C6E6", NULL }, /* Packet mode */ - [8] = { "8890218F", NULL }, /* 56 kbit/s rate adaptation */ - [9] = { "9190A5", NULL }, /* Unrestricted digital information - * with tones/announcements */ - [16] = { "8090A3", "9181" }, /* Telephony */ - [17] = { "9090A3", "9184" }, /* Group 2/3 facsimile */ - [18] = { "8890", "91A1" }, /* Group 4 facsimile Class 1 */ - [19] = { "8890", "91A4" }, /* Teletex service basic and mixed mode - * and Group 4 facsimile service - * Classes II and III */ - [20] = { "8890", "91A8" }, /* Teletex service basic and - * processable mode */ - [21] = { "8890", "91B1" }, /* Teletex service basic mode */ - [22] = { "8890", "91B2" }, /* International interworking for - * Videotex */ - [23] = { "8890", "91B5" }, /* Telex */ - [24] = { "8890", "91B8" }, /* Message Handling Systems - * in accordance with X.400 */ - [25] = { "8890", "91C1" }, /* OSI application - * in accordance with X.200 */ - [26] = { "9190A5", "9181" }, /* 7 kHz telephony */ - [27] = { "9190A5", "916001" }, /* Video telephony, first connection */ - [28] = { "8890", "916002" }, /* Video telephony, second connection */ -}; - -/* - * helper functions - * ================ - */ - -/* - * emit unsupported parameter warning - */ -static inline void ignore_cstruct_param(struct cardstate *cs, _cstruct param, - char *msgname, char *paramname) -{ - if (param && *param) - dev_warn(cs->dev, "%s: ignoring unsupported parameter: %s\n", - msgname, paramname); -} - -/* - * convert an IE from Gigaset hex string to ETSI binary representation - * including length byte - * return value: result length, -1 on error - */ -static int encode_ie(char *in, u8 *out, int maxlen) -{ - int l = 0; - while (*in) { - if (!isxdigit(in[0]) || !isxdigit(in[1]) || l >= maxlen) - return -1; - out[++l] = (hex_to_bin(in[0]) << 4) + hex_to_bin(in[1]); - in += 2; - } - out[0] = l; - return l; -} - -/* - * convert an IE from ETSI binary representation including length byte - * to Gigaset hex string - */ -static void decode_ie(u8 *in, char *out) -{ - int i = *in; - while (i-- > 0) { - /* ToDo: conversion to upper case necessary? */ - *out++ = toupper(hex_asc_hi(*++in)); - *out++ = toupper(hex_asc_lo(*in)); - } -} - -/* - * retrieve application data structure for an application ID - */ -static inline struct gigaset_capi_appl * -get_appl(struct gigaset_capi_ctr *iif, u16 appl) -{ - struct gigaset_capi_appl *ap; - - list_for_each_entry(ap, &iif->appls, ctrlist) - if (ap->id == appl) - return ap; - return NULL; -} - -/* - * dump CAPI message to kernel messages for debugging - */ -static inline void dump_cmsg(enum debuglevel level, const char *tag, _cmsg *p) -{ -#ifdef CONFIG_GIGASET_DEBUG - /* dump at most 20 messages in 20 secs */ - static DEFINE_RATELIMIT_STATE(msg_dump_ratelimit, 20 * HZ, 20); - _cdebbuf *cdb; - - if (!(gigaset_debuglevel & level)) - return; - if (!___ratelimit(&msg_dump_ratelimit, tag)) - return; - - cdb = capi_cmsg2str(p); - if (cdb) { - gig_dbg(level, "%s: [%d] %s", tag, p->ApplId, cdb->buf); - cdebbuf_free(cdb); - } else { - gig_dbg(level, "%s: [%d] %s", tag, p->ApplId, - capi_cmd2str(p->Command, p->Subcommand)); - } -#endif -} - -static inline void dump_rawmsg(enum debuglevel level, const char *tag, - unsigned char *data) -{ -#ifdef CONFIG_GIGASET_DEBUG - char *dbgline; - int i, l; - - if (!(gigaset_debuglevel & level)) - return; - - l = CAPIMSG_LEN(data); - if (l < 12) { - gig_dbg(level, "%s: ??? LEN=%04d", tag, l); - return; - } - gig_dbg(level, "%s: 0x%02x:0x%02x: ID=%03d #0x%04x LEN=%04d NCCI=0x%x", - tag, CAPIMSG_COMMAND(data), CAPIMSG_SUBCOMMAND(data), - CAPIMSG_APPID(data), CAPIMSG_MSGID(data), l, - CAPIMSG_CONTROL(data)); - l -= 12; - if (l <= 0) - return; - if (l > 64) - l = 64; /* arbitrary limit */ - dbgline = kmalloc_array(3, l, GFP_ATOMIC); - if (!dbgline) - return; - for (i = 0; i < l; i++) { - dbgline[3 * i] = hex_asc_hi(data[12 + i]); - dbgline[3 * i + 1] = hex_asc_lo(data[12 + i]); - dbgline[3 * i + 2] = ' '; - } - dbgline[3 * l - 1] = '\0'; - gig_dbg(level, " %s", dbgline); - kfree(dbgline); - if (CAPIMSG_COMMAND(data) == CAPI_DATA_B3 && - (CAPIMSG_SUBCOMMAND(data) == CAPI_REQ || - CAPIMSG_SUBCOMMAND(data) == CAPI_IND)) { - l = CAPIMSG_DATALEN(data); - gig_dbg(level, " DataLength=%d", l); - if (l <= 0 || !(gigaset_debuglevel & DEBUG_LLDATA)) - return; - if (l > 64) - l = 64; /* arbitrary limit */ - dbgline = kmalloc_array(3, l, GFP_ATOMIC); - if (!dbgline) - return; - data += CAPIMSG_LEN(data); - for (i = 0; i < l; i++) { - dbgline[3 * i] = hex_asc_hi(data[i]); - dbgline[3 * i + 1] = hex_asc_lo(data[i]); - dbgline[3 * i + 2] = ' '; - } - dbgline[3 * l - 1] = '\0'; - gig_dbg(level, " %s", dbgline); - kfree(dbgline); - } -#endif -} - -/* - * format CAPI IE as string - */ - -#ifdef CONFIG_GIGASET_DEBUG -static const char *format_ie(const char *ie) -{ - static char result[3 * MAX_FMT_IE_LEN]; - int len, count; - char *pout = result; - - if (!ie) - return "NULL"; - - count = len = ie[0]; - if (count > MAX_FMT_IE_LEN) - count = MAX_FMT_IE_LEN - 1; - while (count--) { - *pout++ = hex_asc_hi(*++ie); - *pout++ = hex_asc_lo(*ie); - *pout++ = ' '; - } - if (len > MAX_FMT_IE_LEN) { - *pout++ = '.'; - *pout++ = '.'; - *pout++ = '.'; - } - *--pout = 0; - return result; -} -#endif - -/* - * emit DATA_B3_CONF message - */ -static void send_data_b3_conf(struct cardstate *cs, struct capi_ctr *ctr, - u16 appl, u16 msgid, int channel, - u16 handle, u16 info) -{ - struct sk_buff *cskb; - u8 *msg; - - cskb = alloc_skb(CAPI_DATA_B3_CONF_LEN, GFP_ATOMIC); - if (!cskb) { - dev_err(cs->dev, "%s: out of memory\n", __func__); - return; - } - /* frequent message, avoid _cmsg overhead */ - msg = __skb_put(cskb, CAPI_DATA_B3_CONF_LEN); - CAPIMSG_SETLEN(msg, CAPI_DATA_B3_CONF_LEN); - CAPIMSG_SETAPPID(msg, appl); - CAPIMSG_SETCOMMAND(msg, CAPI_DATA_B3); - CAPIMSG_SETSUBCOMMAND(msg, CAPI_CONF); - CAPIMSG_SETMSGID(msg, msgid); - CAPIMSG_SETCONTROLLER(msg, ctr->cnr); - CAPIMSG_SETPLCI_PART(msg, channel); - CAPIMSG_SETNCCI_PART(msg, 1); - CAPIMSG_SETHANDLE_CONF(msg, handle); - CAPIMSG_SETINFO_CONF(msg, info); - - /* emit message */ - dump_rawmsg(DEBUG_MCMD, __func__, msg); - capi_ctr_handle_message(ctr, appl, cskb); -} - - -/* - * driver interface functions - * ========================== - */ - -/** - * gigaset_skb_sent() - acknowledge transmission of outgoing skb - * @bcs: B channel descriptor structure. - * @skb: sent data. - * - * Called by hardware module {bas,ser,usb}_gigaset when the data in a - * skb has been successfully sent, for signalling completion to the LL. - */ -void gigaset_skb_sent(struct bc_state *bcs, struct sk_buff *dskb) -{ - struct cardstate *cs = bcs->cs; - struct gigaset_capi_ctr *iif = cs->iif; - struct gigaset_capi_appl *ap = bcs->ap; - unsigned char *req = skb_mac_header(dskb); - u16 flags; - - /* update statistics */ - ++bcs->trans_up; - - if (!ap) { - gig_dbg(DEBUG_MCMD, "%s: application gone", __func__); - return; - } - - /* don't send further B3 messages if disconnected */ - if (bcs->apconnstate < APCONN_ACTIVE) { - gig_dbg(DEBUG_MCMD, "%s: disconnected", __func__); - return; - } - - /* - * send DATA_B3_CONF if "delivery confirmation" bit was set in request; - * otherwise it has already been sent by do_data_b3_req() - */ - flags = CAPIMSG_FLAGS(req); - if (flags & CAPI_FLAGS_DELIVERY_CONFIRMATION) - send_data_b3_conf(cs, &iif->ctr, ap->id, CAPIMSG_MSGID(req), - bcs->channel + 1, CAPIMSG_HANDLE_REQ(req), - (flags & ~CAPI_FLAGS_DELIVERY_CONFIRMATION) ? - CapiFlagsNotSupportedByProtocol : - CAPI_NOERROR); -} -EXPORT_SYMBOL_GPL(gigaset_skb_sent); - -/** - * gigaset_skb_rcvd() - pass received skb to LL - * @bcs: B channel descriptor structure. - * @skb: received data. - * - * Called by hardware module {bas,ser,usb}_gigaset when user data has - * been successfully received, for passing to the LL. - * Warning: skb must not be accessed anymore! - */ -void gigaset_skb_rcvd(struct bc_state *bcs, struct sk_buff *skb) -{ - struct cardstate *cs = bcs->cs; - struct gigaset_capi_ctr *iif = cs->iif; - struct gigaset_capi_appl *ap = bcs->ap; - int len = skb->len; - - /* update statistics */ - bcs->trans_down++; - - if (!ap) { - gig_dbg(DEBUG_MCMD, "%s: application gone", __func__); - dev_kfree_skb_any(skb); - return; - } - - /* don't send further B3 messages if disconnected */ - if (bcs->apconnstate < APCONN_ACTIVE) { - gig_dbg(DEBUG_MCMD, "%s: disconnected", __func__); - dev_kfree_skb_any(skb); - return; - } - - /* - * prepend DATA_B3_IND message to payload - * Parameters: NCCI = 1, all others 0/unused - * frequent message, avoid _cmsg overhead - */ - skb_push(skb, CAPI_DATA_B3_REQ_LEN); - CAPIMSG_SETLEN(skb->data, CAPI_DATA_B3_REQ_LEN); - CAPIMSG_SETAPPID(skb->data, ap->id); - CAPIMSG_SETCOMMAND(skb->data, CAPI_DATA_B3); - CAPIMSG_SETSUBCOMMAND(skb->data, CAPI_IND); - CAPIMSG_SETMSGID(skb->data, ap->nextMessageNumber++); - CAPIMSG_SETCONTROLLER(skb->data, iif->ctr.cnr); - CAPIMSG_SETPLCI_PART(skb->data, bcs->channel + 1); - CAPIMSG_SETNCCI_PART(skb->data, 1); - /* Data parameter not used */ - CAPIMSG_SETDATALEN(skb->data, len); - /* Data handle parameter not used */ - CAPIMSG_SETFLAGS(skb->data, 0); - /* Data64 parameter not present */ - - /* emit message */ - dump_rawmsg(DEBUG_MCMD, __func__, skb->data); - capi_ctr_handle_message(&iif->ctr, ap->id, skb); -} -EXPORT_SYMBOL_GPL(gigaset_skb_rcvd); - -/** - * gigaset_isdn_rcv_err() - signal receive error - * @bcs: B channel descriptor structure. - * - * Called by hardware module {bas,ser,usb}_gigaset when a receive error - * has occurred, for signalling to the LL. - */ -void gigaset_isdn_rcv_err(struct bc_state *bcs) -{ - /* if currently ignoring packets, just count down */ - if (bcs->ignore) { - bcs->ignore--; - return; - } - - /* update statistics */ - bcs->corrupted++; - - /* ToDo: signal error -> LL */ -} -EXPORT_SYMBOL_GPL(gigaset_isdn_rcv_err); - -/** - * gigaset_isdn_icall() - signal incoming call - * @at_state: connection state structure. - * - * Called by main module at tasklet level to notify the LL that an incoming - * call has been received. @at_state contains the parameters of the call. - * - * Return value: call disposition (ICALL_*) - */ -int gigaset_isdn_icall(struct at_state_t *at_state) -{ - struct cardstate *cs = at_state->cs; - struct bc_state *bcs = at_state->bcs; - struct gigaset_capi_ctr *iif = cs->iif; - struct gigaset_capi_appl *ap; - u32 actCIPmask; - struct sk_buff *skb; - unsigned int msgsize; - unsigned long flags; - int i; - - /* - * ToDo: signal calls without a free B channel, too - * (requires a u8 handle for the at_state structure that can - * be stored in the PLCI and used in the CONNECT_RESP message - * handler to retrieve it) - */ - if (!bcs) - return ICALL_IGNORE; - - /* prepare CONNECT_IND message, using B channel number as PLCI */ - capi_cmsg_header(&iif->hcmsg, 0, CAPI_CONNECT, CAPI_IND, 0, - iif->ctr.cnr | ((bcs->channel + 1) << 8)); - - /* minimum size, all structs empty */ - msgsize = CAPI_CONNECT_IND_BASELEN; - - /* Bearer Capability (mandatory) */ - if (at_state->str_var[STR_ZBC]) { - /* pass on BC from Gigaset */ - if (encode_ie(at_state->str_var[STR_ZBC], iif->bc_buf, - MAX_BC_OCTETS) < 0) { - dev_warn(cs->dev, "RING ignored - bad BC %s\n", - at_state->str_var[STR_ZBC]); - return ICALL_IGNORE; - } - - /* look up corresponding CIP value */ - iif->hcmsg.CIPValue = 0; /* default if nothing found */ - for (i = 0; i < ARRAY_SIZE(cip2bchlc); i++) - if (cip2bchlc[i].bc != NULL && - cip2bchlc[i].hlc == NULL && - !strcmp(cip2bchlc[i].bc, - at_state->str_var[STR_ZBC])) { - iif->hcmsg.CIPValue = i; - break; - } - } else { - /* no BC (internal call): assume CIP 1 (speech, A-law) */ - iif->hcmsg.CIPValue = 1; - encode_ie(cip2bchlc[1].bc, iif->bc_buf, MAX_BC_OCTETS); - } - iif->hcmsg.BC = iif->bc_buf; - msgsize += iif->hcmsg.BC[0]; - - /* High Layer Compatibility (optional) */ - if (at_state->str_var[STR_ZHLC]) { - /* pass on HLC from Gigaset */ - if (encode_ie(at_state->str_var[STR_ZHLC], iif->hlc_buf, - MAX_HLC_OCTETS) < 0) { - dev_warn(cs->dev, "RING ignored - bad HLC %s\n", - at_state->str_var[STR_ZHLC]); - return ICALL_IGNORE; - } - iif->hcmsg.HLC = iif->hlc_buf; - msgsize += iif->hcmsg.HLC[0]; - - /* look up corresponding CIP value */ - /* keep BC based CIP value if none found */ - if (at_state->str_var[STR_ZBC]) - for (i = 0; i < ARRAY_SIZE(cip2bchlc); i++) - if (cip2bchlc[i].hlc != NULL && - !strcmp(cip2bchlc[i].hlc, - at_state->str_var[STR_ZHLC]) && - !strcmp(cip2bchlc[i].bc, - at_state->str_var[STR_ZBC])) { - iif->hcmsg.CIPValue = i; - break; - } - } - - /* Called Party Number (optional) */ - if (at_state->str_var[STR_ZCPN]) { - i = strlen(at_state->str_var[STR_ZCPN]); - if (i > MAX_NUMBER_DIGITS) { - dev_warn(cs->dev, "RING ignored - bad number %s\n", - at_state->str_var[STR_ZBC]); - return ICALL_IGNORE; - } - iif->cdpty_buf[0] = i + 1; - iif->cdpty_buf[1] = 0x80; /* type / numbering plan unknown */ - memcpy(iif->cdpty_buf + 2, at_state->str_var[STR_ZCPN], i); - iif->hcmsg.CalledPartyNumber = iif->cdpty_buf; - msgsize += iif->hcmsg.CalledPartyNumber[0]; - } - - /* Calling Party Number (optional) */ - if (at_state->str_var[STR_NMBR]) { - i = strlen(at_state->str_var[STR_NMBR]); - if (i > MAX_NUMBER_DIGITS) { - dev_warn(cs->dev, "RING ignored - bad number %s\n", - at_state->str_var[STR_ZBC]); - return ICALL_IGNORE; - } - iif->cgpty_buf[0] = i + 2; - iif->cgpty_buf[1] = 0x00; /* type / numbering plan unknown */ - iif->cgpty_buf[2] = 0x80; /* pres. allowed, not screened */ - memcpy(iif->cgpty_buf + 3, at_state->str_var[STR_NMBR], i); - iif->hcmsg.CallingPartyNumber = iif->cgpty_buf; - msgsize += iif->hcmsg.CallingPartyNumber[0]; - } - - /* remaining parameters (not supported, always left NULL): - * - CalledPartySubaddress - * - CallingPartySubaddress - * - AdditionalInfo - * - BChannelinformation - * - Keypadfacility - * - Useruserdata - * - Facilitydataarray - */ - - gig_dbg(DEBUG_CMD, "icall: PLCI %x CIP %d BC %s", - iif->hcmsg.adr.adrPLCI, iif->hcmsg.CIPValue, - format_ie(iif->hcmsg.BC)); - gig_dbg(DEBUG_CMD, "icall: HLC %s", - format_ie(iif->hcmsg.HLC)); - gig_dbg(DEBUG_CMD, "icall: CgPty %s", - format_ie(iif->hcmsg.CallingPartyNumber)); - gig_dbg(DEBUG_CMD, "icall: CdPty %s", - format_ie(iif->hcmsg.CalledPartyNumber)); - - /* scan application list for matching listeners */ - spin_lock_irqsave(&bcs->aplock, flags); - if (bcs->ap != NULL || bcs->apconnstate != APCONN_NONE) { - dev_warn(cs->dev, "%s: channel not properly cleared (%p/%d)\n", - __func__, bcs->ap, bcs->apconnstate); - bcs->ap = NULL; - bcs->apconnstate = APCONN_NONE; - } - spin_unlock_irqrestore(&bcs->aplock, flags); - actCIPmask = 1 | (1 << iif->hcmsg.CIPValue); - list_for_each_entry(ap, &iif->appls, ctrlist) - if (actCIPmask & ap->listenCIPmask) { - /* build CONNECT_IND message for this application */ - iif->hcmsg.ApplId = ap->id; - iif->hcmsg.Messagenumber = ap->nextMessageNumber++; - - skb = alloc_skb(msgsize, GFP_ATOMIC); - if (!skb) { - dev_err(cs->dev, "%s: out of memory\n", - __func__); - break; - } - if (capi_cmsg2message(&iif->hcmsg, - __skb_put(skb, msgsize))) { - dev_err(cs->dev, "%s: message parser failure\n", - __func__); - dev_kfree_skb_any(skb); - break; - } - dump_cmsg(DEBUG_CMD, __func__, &iif->hcmsg); - - /* add to listeners on this B channel, update state */ - spin_lock_irqsave(&bcs->aplock, flags); - ap->bcnext = bcs->ap; - bcs->ap = ap; - bcs->chstate |= CHS_NOTIFY_LL; - bcs->apconnstate = APCONN_SETUP; - spin_unlock_irqrestore(&bcs->aplock, flags); - - /* emit message */ - capi_ctr_handle_message(&iif->ctr, ap->id, skb); - } - - /* - * Return "accept" if any listeners. - * Gigaset will send ALERTING. - * There doesn't seem to be a way to avoid this. - */ - return bcs->ap ? ICALL_ACCEPT : ICALL_IGNORE; -} - -/* - * send a DISCONNECT_IND message to an application - * does not sleep, clobbers the controller's hcmsg structure - */ -static void send_disconnect_ind(struct bc_state *bcs, - struct gigaset_capi_appl *ap, u16 reason) -{ - struct cardstate *cs = bcs->cs; - struct gigaset_capi_ctr *iif = cs->iif; - struct sk_buff *skb; - - if (bcs->apconnstate == APCONN_NONE) - return; - - capi_cmsg_header(&iif->hcmsg, ap->id, CAPI_DISCONNECT, CAPI_IND, - ap->nextMessageNumber++, - iif->ctr.cnr | ((bcs->channel + 1) << 8)); - iif->hcmsg.Reason = reason; - skb = alloc_skb(CAPI_DISCONNECT_IND_LEN, GFP_ATOMIC); - if (!skb) { - dev_err(cs->dev, "%s: out of memory\n", __func__); - return; - } - if (capi_cmsg2message(&iif->hcmsg, - __skb_put(skb, CAPI_DISCONNECT_IND_LEN))) { - dev_err(cs->dev, "%s: message parser failure\n", __func__); - dev_kfree_skb_any(skb); - return; - } - dump_cmsg(DEBUG_CMD, __func__, &iif->hcmsg); - capi_ctr_handle_message(&iif->ctr, ap->id, skb); -} - -/* - * send a DISCONNECT_B3_IND message to an application - * Parameters: NCCI = 1, NCPI empty, Reason_B3 = 0 - * does not sleep, clobbers the controller's hcmsg structure - */ -static void send_disconnect_b3_ind(struct bc_state *bcs, - struct gigaset_capi_appl *ap) -{ - struct cardstate *cs = bcs->cs; - struct gigaset_capi_ctr *iif = cs->iif; - struct sk_buff *skb; - - /* nothing to do if no logical connection active */ - if (bcs->apconnstate < APCONN_ACTIVE) - return; - bcs->apconnstate = APCONN_SETUP; - - capi_cmsg_header(&iif->hcmsg, ap->id, CAPI_DISCONNECT_B3, CAPI_IND, - ap->nextMessageNumber++, - iif->ctr.cnr | ((bcs->channel + 1) << 8) | (1 << 16)); - skb = alloc_skb(CAPI_DISCONNECT_B3_IND_BASELEN, GFP_ATOMIC); - if (!skb) { - dev_err(cs->dev, "%s: out of memory\n", __func__); - return; - } - if (capi_cmsg2message(&iif->hcmsg, - __skb_put(skb, CAPI_DISCONNECT_B3_IND_BASELEN))) { - dev_err(cs->dev, "%s: message parser failure\n", __func__); - dev_kfree_skb_any(skb); - return; - } - dump_cmsg(DEBUG_CMD, __func__, &iif->hcmsg); - capi_ctr_handle_message(&iif->ctr, ap->id, skb); -} - -/** - * gigaset_isdn_connD() - signal D channel connect - * @bcs: B channel descriptor structure. - * - * Called by main module at tasklet level to notify the LL that the D channel - * connection has been established. - */ -void gigaset_isdn_connD(struct bc_state *bcs) -{ - struct cardstate *cs = bcs->cs; - struct gigaset_capi_ctr *iif = cs->iif; - struct gigaset_capi_appl *ap; - struct sk_buff *skb; - unsigned int msgsize; - unsigned long flags; - - spin_lock_irqsave(&bcs->aplock, flags); - ap = bcs->ap; - if (!ap) { - spin_unlock_irqrestore(&bcs->aplock, flags); - gig_dbg(DEBUG_CMD, "%s: application gone", __func__); - return; - } - if (bcs->apconnstate == APCONN_NONE) { - spin_unlock_irqrestore(&bcs->aplock, flags); - dev_warn(cs->dev, "%s: application %u not connected\n", - __func__, ap->id); - return; - } - spin_unlock_irqrestore(&bcs->aplock, flags); - while (ap->bcnext) { - /* this should never happen */ - dev_warn(cs->dev, "%s: dropping extra application %u\n", - __func__, ap->bcnext->id); - send_disconnect_ind(bcs, ap->bcnext, - CapiCallGivenToOtherApplication); - ap->bcnext = ap->bcnext->bcnext; - } - - /* prepare CONNECT_ACTIVE_IND message - * Note: LLC not supported by device - */ - capi_cmsg_header(&iif->hcmsg, ap->id, CAPI_CONNECT_ACTIVE, CAPI_IND, - ap->nextMessageNumber++, - iif->ctr.cnr | ((bcs->channel + 1) << 8)); - - /* minimum size, all structs empty */ - msgsize = CAPI_CONNECT_ACTIVE_IND_BASELEN; - - /* ToDo: set parameter: Connected number - * (requires ev-layer state machine extension to collect - * ZCON device reply) - */ - - /* build and emit CONNECT_ACTIVE_IND message */ - skb = alloc_skb(msgsize, GFP_ATOMIC); - if (!skb) { - dev_err(cs->dev, "%s: out of memory\n", __func__); - return; - } - if (capi_cmsg2message(&iif->hcmsg, __skb_put(skb, msgsize))) { - dev_err(cs->dev, "%s: message parser failure\n", __func__); - dev_kfree_skb_any(skb); - return; - } - dump_cmsg(DEBUG_CMD, __func__, &iif->hcmsg); - capi_ctr_handle_message(&iif->ctr, ap->id, skb); -} - -/** - * gigaset_isdn_hupD() - signal D channel hangup - * @bcs: B channel descriptor structure. - * - * Called by main module at tasklet level to notify the LL that the D channel - * connection has been shut down. - */ -void gigaset_isdn_hupD(struct bc_state *bcs) -{ - struct gigaset_capi_appl *ap; - unsigned long flags; - - /* - * ToDo: pass on reason code reported by device - * (requires ev-layer state machine extension to collect - * ZCAU device reply) - */ - spin_lock_irqsave(&bcs->aplock, flags); - while (bcs->ap != NULL) { - ap = bcs->ap; - bcs->ap = ap->bcnext; - spin_unlock_irqrestore(&bcs->aplock, flags); - send_disconnect_b3_ind(bcs, ap); - send_disconnect_ind(bcs, ap, 0); - spin_lock_irqsave(&bcs->aplock, flags); - } - bcs->apconnstate = APCONN_NONE; - spin_unlock_irqrestore(&bcs->aplock, flags); -} - -/** - * gigaset_isdn_connB() - signal B channel connect - * @bcs: B channel descriptor structure. - * - * Called by main module at tasklet level to notify the LL that the B channel - * connection has been established. - */ -void gigaset_isdn_connB(struct bc_state *bcs) -{ - struct cardstate *cs = bcs->cs; - struct gigaset_capi_ctr *iif = cs->iif; - struct gigaset_capi_appl *ap; - struct sk_buff *skb; - unsigned long flags; - unsigned int msgsize; - u8 command; - - spin_lock_irqsave(&bcs->aplock, flags); - ap = bcs->ap; - if (!ap) { - spin_unlock_irqrestore(&bcs->aplock, flags); - gig_dbg(DEBUG_CMD, "%s: application gone", __func__); - return; - } - if (!bcs->apconnstate) { - spin_unlock_irqrestore(&bcs->aplock, flags); - dev_warn(cs->dev, "%s: application %u not connected\n", - __func__, ap->id); - return; - } - - /* - * emit CONNECT_B3_ACTIVE_IND if we already got CONNECT_B3_REQ; - * otherwise we have to emit CONNECT_B3_IND first, and follow up with - * CONNECT_B3_ACTIVE_IND in reply to CONNECT_B3_RESP - * Parameters in both cases always: NCCI = 1, NCPI empty - */ - if (bcs->apconnstate >= APCONN_ACTIVE) { - command = CAPI_CONNECT_B3_ACTIVE; - msgsize = CAPI_CONNECT_B3_ACTIVE_IND_BASELEN; - } else { - command = CAPI_CONNECT_B3; - msgsize = CAPI_CONNECT_B3_IND_BASELEN; - } - bcs->apconnstate = APCONN_ACTIVE; - - spin_unlock_irqrestore(&bcs->aplock, flags); - - while (ap->bcnext) { - /* this should never happen */ - dev_warn(cs->dev, "%s: dropping extra application %u\n", - __func__, ap->bcnext->id); - send_disconnect_ind(bcs, ap->bcnext, - CapiCallGivenToOtherApplication); - ap->bcnext = ap->bcnext->bcnext; - } - - capi_cmsg_header(&iif->hcmsg, ap->id, command, CAPI_IND, - ap->nextMessageNumber++, - iif->ctr.cnr | ((bcs->channel + 1) << 8) | (1 << 16)); - skb = alloc_skb(msgsize, GFP_ATOMIC); - if (!skb) { - dev_err(cs->dev, "%s: out of memory\n", __func__); - return; - } - if (capi_cmsg2message(&iif->hcmsg, __skb_put(skb, msgsize))) { - dev_err(cs->dev, "%s: message parser failure\n", __func__); - dev_kfree_skb_any(skb); - return; - } - dump_cmsg(DEBUG_CMD, __func__, &iif->hcmsg); - capi_ctr_handle_message(&iif->ctr, ap->id, skb); -} - -/** - * gigaset_isdn_hupB() - signal B channel hangup - * @bcs: B channel descriptor structure. - * - * Called by main module to notify the LL that the B channel connection has - * been shut down. - */ -void gigaset_isdn_hupB(struct bc_state *bcs) -{ - struct gigaset_capi_appl *ap = bcs->ap; - - /* ToDo: assure order of DISCONNECT_B3_IND and DISCONNECT_IND ? */ - - if (!ap) { - gig_dbg(DEBUG_CMD, "%s: application gone", __func__); - return; - } - - send_disconnect_b3_ind(bcs, ap); -} - -/** - * gigaset_isdn_start() - signal device availability - * @cs: device descriptor structure. - * - * Called by main module to notify the LL that the device is available for - * use. - */ -void gigaset_isdn_start(struct cardstate *cs) -{ - struct gigaset_capi_ctr *iif = cs->iif; - - /* fill profile data: manufacturer name */ - strcpy(iif->ctr.manu, "Siemens"); - /* CAPI and device version */ - iif->ctr.version.majorversion = 2; /* CAPI 2.0 */ - iif->ctr.version.minorversion = 0; - /* ToDo: check/assert cs->gotfwver? */ - iif->ctr.version.majormanuversion = cs->fwver[0]; - iif->ctr.version.minormanuversion = cs->fwver[1]; - /* number of B channels supported */ - iif->ctr.profile.nbchannel = cs->channels; - /* global options: internal controller, supplementary services */ - iif->ctr.profile.goptions = 0x11; - /* B1 protocols: 64 kbit/s HDLC or transparent */ - iif->ctr.profile.support1 = 0x03; - /* B2 protocols: transparent only */ - /* ToDo: X.75 SLP ? */ - iif->ctr.profile.support2 = 0x02; - /* B3 protocols: transparent only */ - iif->ctr.profile.support3 = 0x01; - /* no serial number */ - strcpy(iif->ctr.serial, "0"); - capi_ctr_ready(&iif->ctr); -} - -/** - * gigaset_isdn_stop() - signal device unavailability - * @cs: device descriptor structure. - * - * Called by main module to notify the LL that the device is no longer - * available for use. - */ -void gigaset_isdn_stop(struct cardstate *cs) -{ - struct gigaset_capi_ctr *iif = cs->iif; - capi_ctr_down(&iif->ctr); -} - -/* - * kernel CAPI callback methods - * ============================ - */ - -/* - * register CAPI application - */ -static void gigaset_register_appl(struct capi_ctr *ctr, u16 appl, - capi_register_params *rp) -{ - struct gigaset_capi_ctr *iif - = container_of(ctr, struct gigaset_capi_ctr, ctr); - struct cardstate *cs = ctr->driverdata; - struct gigaset_capi_appl *ap; - - gig_dbg(DEBUG_CMD, "%s [%u] l3cnt=%u blkcnt=%u blklen=%u", - __func__, appl, rp->level3cnt, rp->datablkcnt, rp->datablklen); - - list_for_each_entry(ap, &iif->appls, ctrlist) - if (ap->id == appl) { - dev_notice(cs->dev, - "application %u already registered\n", appl); - return; - } - - ap = kzalloc(sizeof(*ap), GFP_KERNEL); - if (!ap) { - dev_err(cs->dev, "%s: out of memory\n", __func__); - return; - } - ap->id = appl; - ap->rp = *rp; - - list_add(&ap->ctrlist, &iif->appls); - dev_info(cs->dev, "application %u registered\n", ap->id); -} - -/* - * remove CAPI application from channel - * helper function to keep indentation levels down and stay in 80 columns - */ - -static inline void remove_appl_from_channel(struct bc_state *bcs, - struct gigaset_capi_appl *ap) -{ - struct cardstate *cs = bcs->cs; - struct gigaset_capi_appl *bcap; - unsigned long flags; - int prevconnstate; - - spin_lock_irqsave(&bcs->aplock, flags); - bcap = bcs->ap; - if (bcap == NULL) { - spin_unlock_irqrestore(&bcs->aplock, flags); - return; - } - - /* check first application on channel */ - if (bcap == ap) { - bcs->ap = ap->bcnext; - if (bcs->ap != NULL) { - spin_unlock_irqrestore(&bcs->aplock, flags); - return; - } - - /* none left, clear channel state */ - prevconnstate = bcs->apconnstate; - bcs->apconnstate = APCONN_NONE; - spin_unlock_irqrestore(&bcs->aplock, flags); - - if (prevconnstate == APCONN_ACTIVE) { - dev_notice(cs->dev, "%s: hanging up channel %u\n", - __func__, bcs->channel); - gigaset_add_event(cs, &bcs->at_state, - EV_HUP, NULL, 0, NULL); - gigaset_schedule_event(cs); - } - return; - } - - /* check remaining list */ - do { - if (bcap->bcnext == ap) { - bcap->bcnext = bcap->bcnext->bcnext; - spin_unlock_irqrestore(&bcs->aplock, flags); - return; - } - bcap = bcap->bcnext; - } while (bcap != NULL); - spin_unlock_irqrestore(&bcs->aplock, flags); -} - -/* - * release CAPI application - */ -static void gigaset_release_appl(struct capi_ctr *ctr, u16 appl) -{ - struct gigaset_capi_ctr *iif - = container_of(ctr, struct gigaset_capi_ctr, ctr); - struct cardstate *cs = iif->ctr.driverdata; - struct gigaset_capi_appl *ap, *tmp; - unsigned ch; - - gig_dbg(DEBUG_CMD, "%s [%u]", __func__, appl); - - list_for_each_entry_safe(ap, tmp, &iif->appls, ctrlist) - if (ap->id == appl) { - /* remove from any channels */ - for (ch = 0; ch < cs->channels; ch++) - remove_appl_from_channel(&cs->bcs[ch], ap); - - /* remove from registration list */ - list_del(&ap->ctrlist); - kfree(ap); - dev_info(cs->dev, "application %u released\n", appl); - } -} - -/* - * ===================================================================== - * outgoing CAPI message handler - * ===================================================================== - */ - -/* - * helper function: emit reply message with given Info value - */ -static void send_conf(struct gigaset_capi_ctr *iif, - struct gigaset_capi_appl *ap, - struct sk_buff *skb, - u16 info) -{ - struct cardstate *cs = iif->ctr.driverdata; - - /* - * _CONF replies always only have NCCI and Info parameters - * so they'll fit into the _REQ message skb - */ - capi_cmsg_answer(&iif->acmsg); - iif->acmsg.Info = info; - if (capi_cmsg2message(&iif->acmsg, skb->data)) { - dev_err(cs->dev, "%s: message parser failure\n", __func__); - dev_kfree_skb_any(skb); - return; - } - __skb_trim(skb, CAPI_STDCONF_LEN); - dump_cmsg(DEBUG_CMD, __func__, &iif->acmsg); - capi_ctr_handle_message(&iif->ctr, ap->id, skb); -} - -/* - * process FACILITY_REQ message - */ -static void do_facility_req(struct gigaset_capi_ctr *iif, - struct gigaset_capi_appl *ap, - struct sk_buff *skb) -{ - struct cardstate *cs = iif->ctr.driverdata; - _cmsg *cmsg = &iif->acmsg; - struct sk_buff *cskb; - u8 *pparam; - unsigned int msgsize = CAPI_FACILITY_CONF_BASELEN; - u16 function, info; - static u8 confparam[10]; /* max. 9 octets + length byte */ - - /* decode message */ - if (capi_message2cmsg(cmsg, skb->data)) { - dev_err(cs->dev, "%s: message parser failure\n", __func__); - dev_kfree_skb_any(skb); - return; - } - dump_cmsg(DEBUG_CMD, __func__, cmsg); - - /* - * Facility Request Parameter is not decoded by capi_message2cmsg() - * encoding depends on Facility Selector - */ - switch (cmsg->FacilitySelector) { - case CAPI_FACILITY_DTMF: /* ToDo */ - info = CapiFacilityNotSupported; - confparam[0] = 2; /* length */ - /* DTMF information: Unknown DTMF request */ - capimsg_setu16(confparam, 1, 2); - break; - - case CAPI_FACILITY_V42BIS: /* not supported */ - info = CapiFacilityNotSupported; - confparam[0] = 2; /* length */ - /* V.42 bis information: not available */ - capimsg_setu16(confparam, 1, 1); - break; - - case CAPI_FACILITY_SUPPSVC: - /* decode Function parameter */ - pparam = cmsg->FacilityRequestParameter; - if (pparam == NULL || pparam[0] < 2) { - dev_notice(cs->dev, "%s: %s missing\n", "FACILITY_REQ", - "Facility Request Parameter"); - send_conf(iif, ap, skb, CapiIllMessageParmCoding); - return; - } - function = CAPIMSG_U16(pparam, 1); - switch (function) { - case CAPI_SUPPSVC_GETSUPPORTED: - info = CapiSuccess; - /* Supplementary Service specific parameter */ - confparam[3] = 6; /* length */ - /* Supplementary services info: Success */ - capimsg_setu16(confparam, 4, CapiSuccess); - /* Supported Services: none */ - capimsg_setu32(confparam, 6, 0); - break; - case CAPI_SUPPSVC_LISTEN: - if (pparam[0] < 7 || pparam[3] < 4) { - dev_notice(cs->dev, "%s: %s missing\n", - "FACILITY_REQ", "Notification Mask"); - send_conf(iif, ap, skb, - CapiIllMessageParmCoding); - return; - } - if (CAPIMSG_U32(pparam, 4) != 0) { - dev_notice(cs->dev, - "%s: unsupported supplementary service notification mask 0x%x\n", - "FACILITY_REQ", CAPIMSG_U32(pparam, 4)); - info = CapiFacilitySpecificFunctionNotSupported; - confparam[3] = 2; /* length */ - capimsg_setu16(confparam, 4, - CapiSupplementaryServiceNotSupported); - break; - } - info = CapiSuccess; - confparam[3] = 2; /* length */ - capimsg_setu16(confparam, 4, CapiSuccess); - break; - - /* ToDo: add supported services */ - - default: - dev_notice(cs->dev, - "%s: unsupported supplementary service function 0x%04x\n", - "FACILITY_REQ", function); - info = CapiFacilitySpecificFunctionNotSupported; - /* Supplementary Service specific parameter */ - confparam[3] = 2; /* length */ - /* Supplementary services info: not supported */ - capimsg_setu16(confparam, 4, - CapiSupplementaryServiceNotSupported); - } - - /* Facility confirmation parameter */ - confparam[0] = confparam[3] + 3; /* total length */ - /* Function: copy from _REQ message */ - capimsg_setu16(confparam, 1, function); - /* Supplementary Service specific parameter already set above */ - break; - - case CAPI_FACILITY_WAKEUP: /* ToDo */ - info = CapiFacilityNotSupported; - confparam[0] = 2; /* length */ - /* Number of accepted awake request parameters: 0 */ - capimsg_setu16(confparam, 1, 0); - break; - - default: - info = CapiFacilityNotSupported; - confparam[0] = 0; /* empty struct */ - } - - /* send FACILITY_CONF with given Info and confirmation parameter */ - dev_kfree_skb_any(skb); - capi_cmsg_answer(cmsg); - cmsg->Info = info; - cmsg->FacilityConfirmationParameter = confparam; - msgsize += confparam[0]; /* length */ - cskb = alloc_skb(msgsize, GFP_ATOMIC); - if (!cskb) { - dev_err(cs->dev, "%s: out of memory\n", __func__); - return; - } - if (capi_cmsg2message(cmsg, __skb_put(cskb, msgsize))) { - dev_err(cs->dev, "%s: message parser failure\n", __func__); - dev_kfree_skb_any(cskb); - return; - } - dump_cmsg(DEBUG_CMD, __func__, cmsg); - capi_ctr_handle_message(&iif->ctr, ap->id, cskb); -} - - -/* - * process LISTEN_REQ message - * just store the masks in the application data structure - */ -static void do_listen_req(struct gigaset_capi_ctr *iif, - struct gigaset_capi_appl *ap, - struct sk_buff *skb) -{ - struct cardstate *cs = iif->ctr.driverdata; - - /* decode message */ - if (capi_message2cmsg(&iif->acmsg, skb->data)) { - dev_err(cs->dev, "%s: message parser failure\n", __func__); - dev_kfree_skb_any(skb); - return; - } - dump_cmsg(DEBUG_CMD, __func__, &iif->acmsg); - - /* store listening parameters */ - ap->listenInfoMask = iif->acmsg.InfoMask; - ap->listenCIPmask = iif->acmsg.CIPmask; - send_conf(iif, ap, skb, CapiSuccess); -} - -/* - * process ALERT_REQ message - * nothing to do, Gigaset always alerts anyway - */ -static void do_alert_req(struct gigaset_capi_ctr *iif, - struct gigaset_capi_appl *ap, - struct sk_buff *skb) -{ - struct cardstate *cs = iif->ctr.driverdata; - - /* decode message */ - if (capi_message2cmsg(&iif->acmsg, skb->data)) { - dev_err(cs->dev, "%s: message parser failure\n", __func__); - dev_kfree_skb_any(skb); - return; - } - dump_cmsg(DEBUG_CMD, __func__, &iif->acmsg); - send_conf(iif, ap, skb, CapiAlertAlreadySent); -} - -/* - * process CONNECT_REQ message - * allocate a B channel, prepare dial commands, queue a DIAL event, - * emit CONNECT_CONF reply - */ -static void do_connect_req(struct gigaset_capi_ctr *iif, - struct gigaset_capi_appl *ap, - struct sk_buff *skb) -{ - struct cardstate *cs = iif->ctr.driverdata; - _cmsg *cmsg = &iif->acmsg; - struct bc_state *bcs; - char **commands; - char *s; - u8 *pp; - unsigned long flags; - int i, l, lbc, lhlc; - u16 info; - - /* decode message */ - if (capi_message2cmsg(cmsg, skb->data)) { - dev_err(cs->dev, "%s: message parser failure\n", __func__); - dev_kfree_skb_any(skb); - return; - } - dump_cmsg(DEBUG_CMD, __func__, cmsg); - - /* get free B channel & construct PLCI */ - bcs = gigaset_get_free_channel(cs); - if (!bcs) { - dev_notice(cs->dev, "%s: no B channel available\n", - "CONNECT_REQ"); - send_conf(iif, ap, skb, CapiNoPlciAvailable); - return; - } - spin_lock_irqsave(&bcs->aplock, flags); - if (bcs->ap != NULL || bcs->apconnstate != APCONN_NONE) - dev_warn(cs->dev, "%s: channel not properly cleared (%p/%d)\n", - __func__, bcs->ap, bcs->apconnstate); - ap->bcnext = NULL; - bcs->ap = ap; - bcs->apconnstate = APCONN_SETUP; - spin_unlock_irqrestore(&bcs->aplock, flags); - - bcs->rx_bufsize = ap->rp.datablklen; - dev_kfree_skb(bcs->rx_skb); - gigaset_new_rx_skb(bcs); - cmsg->adr.adrPLCI |= (bcs->channel + 1) << 8; - - /* build command table */ - commands = kcalloc(AT_NUM, sizeof(*commands), GFP_KERNEL); - if (!commands) - goto oom; - - /* encode parameter: Called party number */ - pp = cmsg->CalledPartyNumber; - if (pp == NULL || *pp == 0) { - dev_notice(cs->dev, "%s: %s missing\n", - "CONNECT_REQ", "Called party number"); - info = CapiIllMessageParmCoding; - goto error; - } - l = *pp++; - /* check type of number/numbering plan byte */ - switch (*pp) { - case 0x80: /* unknown type / unknown numbering plan */ - case 0x81: /* unknown type / ISDN/Telephony numbering plan */ - break; - default: /* others: warn about potential misinterpretation */ - dev_notice(cs->dev, "%s: %s type/plan 0x%02x unsupported\n", - "CONNECT_REQ", "Called party number", *pp); - } - pp++; - l--; - /* translate "**" internal call prefix to CTP value */ - if (l >= 2 && pp[0] == '*' && pp[1] == '*') { - s = "^SCTP=0\r"; - pp += 2; - l -= 2; - } else { - s = "^SCTP=1\r"; - } - commands[AT_TYPE] = kstrdup(s, GFP_KERNEL); - if (!commands[AT_TYPE]) - goto oom; - commands[AT_DIAL] = kmalloc(l + 3, GFP_KERNEL); - if (!commands[AT_DIAL]) - goto oom; - snprintf(commands[AT_DIAL], l + 3, "D%.*s\r", l, pp); - - /* encode parameter: Calling party number */ - pp = cmsg->CallingPartyNumber; - if (pp != NULL && *pp > 0) { - l = *pp++; - - /* check type of number/numbering plan byte */ - /* ToDo: allow for/handle Ext=1? */ - switch (*pp) { - case 0x00: /* unknown type / unknown numbering plan */ - case 0x01: /* unknown type / ISDN/Telephony num. plan */ - break; - default: - dev_notice(cs->dev, - "%s: %s type/plan 0x%02x unsupported\n", - "CONNECT_REQ", "Calling party number", *pp); - } - pp++; - l--; - - /* check presentation indicator */ - if (!l) { - dev_notice(cs->dev, "%s: %s IE truncated\n", - "CONNECT_REQ", "Calling party number"); - info = CapiIllMessageParmCoding; - goto error; - } - switch (*pp & 0xfc) { /* ignore Screening indicator */ - case 0x80: /* Presentation allowed */ - s = "^SCLIP=1\r"; - break; - case 0xa0: /* Presentation restricted */ - s = "^SCLIP=0\r"; - break; - default: - dev_notice(cs->dev, "%s: invalid %s 0x%02x\n", - "CONNECT_REQ", - "Presentation/Screening indicator", - *pp); - s = "^SCLIP=1\r"; - } - commands[AT_CLIP] = kstrdup(s, GFP_KERNEL); - if (!commands[AT_CLIP]) - goto oom; - pp++; - l--; - - if (l) { - /* number */ - commands[AT_MSN] = kmalloc(l + 8, GFP_KERNEL); - if (!commands[AT_MSN]) - goto oom; - snprintf(commands[AT_MSN], l + 8, "^SMSN=%*s\r", l, pp); - } - } - - /* check parameter: CIP Value */ - if (cmsg->CIPValue >= ARRAY_SIZE(cip2bchlc) || - (cmsg->CIPValue > 0 && cip2bchlc[cmsg->CIPValue].bc == NULL)) { - dev_notice(cs->dev, "%s: unknown CIP value %d\n", - "CONNECT_REQ", cmsg->CIPValue); - info = CapiCipValueUnknown; - goto error; - } - - /* - * check/encode parameters: BC & HLC - * must be encoded together as device doesn't accept HLC separately - * explicit parameters override values derived from CIP - */ - - /* determine lengths */ - if (cmsg->BC && cmsg->BC[0]) /* BC specified explicitly */ - lbc = 2 * cmsg->BC[0]; - else if (cip2bchlc[cmsg->CIPValue].bc) /* BC derived from CIP */ - lbc = strlen(cip2bchlc[cmsg->CIPValue].bc); - else /* no BC */ - lbc = 0; - if (cmsg->HLC && cmsg->HLC[0]) /* HLC specified explicitly */ - lhlc = 2 * cmsg->HLC[0]; - else if (cip2bchlc[cmsg->CIPValue].hlc) /* HLC derived from CIP */ - lhlc = strlen(cip2bchlc[cmsg->CIPValue].hlc); - else /* no HLC */ - lhlc = 0; - - if (lbc) { - /* have BC: allocate and assemble command string */ - l = lbc + 7; /* "^SBC=" + value + "\r" + null byte */ - if (lhlc) - l += lhlc + 7; /* ";^SHLC=" + value */ - commands[AT_BC] = kmalloc(l, GFP_KERNEL); - if (!commands[AT_BC]) - goto oom; - strcpy(commands[AT_BC], "^SBC="); - if (cmsg->BC && cmsg->BC[0]) /* BC specified explicitly */ - decode_ie(cmsg->BC, commands[AT_BC] + 5); - else /* BC derived from CIP */ - strcpy(commands[AT_BC] + 5, - cip2bchlc[cmsg->CIPValue].bc); - if (lhlc) { - strcpy(commands[AT_BC] + lbc + 5, ";^SHLC="); - if (cmsg->HLC && cmsg->HLC[0]) - /* HLC specified explicitly */ - decode_ie(cmsg->HLC, - commands[AT_BC] + lbc + 12); - else /* HLC derived from CIP */ - strcpy(commands[AT_BC] + lbc + 12, - cip2bchlc[cmsg->CIPValue].hlc); - } - strcpy(commands[AT_BC] + l - 2, "\r"); - } else { - /* no BC */ - if (lhlc) { - dev_notice(cs->dev, "%s: cannot set HLC without BC\n", - "CONNECT_REQ"); - info = CapiIllMessageParmCoding; /* ? */ - goto error; - } - } - - /* check/encode parameter: B Protocol */ - if (cmsg->BProtocol == CAPI_DEFAULT) { - bcs->proto2 = L2_HDLC; - dev_warn(cs->dev, - "B2 Protocol X.75 SLP unsupported, using Transparent\n"); - } else { - switch (cmsg->B1protocol) { - case 0: - bcs->proto2 = L2_HDLC; - break; - case 1: - bcs->proto2 = L2_VOICE; - break; - default: - dev_warn(cs->dev, - "B1 Protocol %u unsupported, using Transparent\n", - cmsg->B1protocol); - bcs->proto2 = L2_VOICE; - } - if (cmsg->B2protocol != 1) - dev_warn(cs->dev, - "B2 Protocol %u unsupported, using Transparent\n", - cmsg->B2protocol); - if (cmsg->B3protocol != 0) - dev_warn(cs->dev, - "B3 Protocol %u unsupported, using Transparent\n", - cmsg->B3protocol); - ignore_cstruct_param(cs, cmsg->B1configuration, - "CONNECT_REQ", "B1 Configuration"); - ignore_cstruct_param(cs, cmsg->B2configuration, - "CONNECT_REQ", "B2 Configuration"); - ignore_cstruct_param(cs, cmsg->B3configuration, - "CONNECT_REQ", "B3 Configuration"); - } - commands[AT_PROTO] = kmalloc(9, GFP_KERNEL); - if (!commands[AT_PROTO]) - goto oom; - snprintf(commands[AT_PROTO], 9, "^SBPR=%u\r", bcs->proto2); - - /* ToDo: check/encode remaining parameters */ - ignore_cstruct_param(cs, cmsg->CalledPartySubaddress, - "CONNECT_REQ", "Called pty subaddr"); - ignore_cstruct_param(cs, cmsg->CallingPartySubaddress, - "CONNECT_REQ", "Calling pty subaddr"); - ignore_cstruct_param(cs, cmsg->LLC, - "CONNECT_REQ", "LLC"); - if (cmsg->AdditionalInfo != CAPI_DEFAULT) { - ignore_cstruct_param(cs, cmsg->BChannelinformation, - "CONNECT_REQ", "B Channel Information"); - ignore_cstruct_param(cs, cmsg->Keypadfacility, - "CONNECT_REQ", "Keypad Facility"); - ignore_cstruct_param(cs, cmsg->Useruserdata, - "CONNECT_REQ", "User-User Data"); - ignore_cstruct_param(cs, cmsg->Facilitydataarray, - "CONNECT_REQ", "Facility Data Array"); - } - - /* encode parameter: B channel to use */ - commands[AT_ISO] = kmalloc(9, GFP_KERNEL); - if (!commands[AT_ISO]) - goto oom; - snprintf(commands[AT_ISO], 9, "^SISO=%u\r", - (unsigned) bcs->channel + 1); - - /* queue & schedule EV_DIAL event */ - if (!gigaset_add_event(cs, &bcs->at_state, EV_DIAL, commands, - bcs->at_state.seq_index, NULL)) { - info = CAPI_MSGOSRESOURCEERR; - goto error; - } - gigaset_schedule_event(cs); - send_conf(iif, ap, skb, CapiSuccess); - return; - -oom: - dev_err(cs->dev, "%s: out of memory\n", __func__); - info = CAPI_MSGOSRESOURCEERR; -error: - if (commands) - for (i = 0; i < AT_NUM; i++) - kfree(commands[i]); - kfree(commands); - gigaset_free_channel(bcs); - send_conf(iif, ap, skb, info); -} - -/* - * process CONNECT_RESP message - * checks protocol parameters and queues an ACCEPT or HUP event - */ -static void do_connect_resp(struct gigaset_capi_ctr *iif, - struct gigaset_capi_appl *ap, - struct sk_buff *skb) -{ - struct cardstate *cs = iif->ctr.driverdata; - _cmsg *cmsg = &iif->acmsg; - struct bc_state *bcs; - struct gigaset_capi_appl *oap; - unsigned long flags; - int channel; - - /* decode message */ - if (capi_message2cmsg(cmsg, skb->data)) { - dev_err(cs->dev, "%s: message parser failure\n", __func__); - dev_kfree_skb_any(skb); - return; - } - dump_cmsg(DEBUG_CMD, __func__, cmsg); - dev_kfree_skb_any(skb); - - /* extract and check channel number from PLCI */ - channel = (cmsg->adr.adrPLCI >> 8) & 0xff; - if (!channel || channel > cs->channels) { - dev_notice(cs->dev, "%s: invalid %s 0x%02x\n", - "CONNECT_RESP", "PLCI", cmsg->adr.adrPLCI); - return; - } - bcs = cs->bcs + channel - 1; - - switch (cmsg->Reject) { - case 0: /* Accept */ - /* drop all competing applications, keep only this one */ - spin_lock_irqsave(&bcs->aplock, flags); - while (bcs->ap != NULL) { - oap = bcs->ap; - bcs->ap = oap->bcnext; - if (oap != ap) { - spin_unlock_irqrestore(&bcs->aplock, flags); - send_disconnect_ind(bcs, oap, - CapiCallGivenToOtherApplication); - spin_lock_irqsave(&bcs->aplock, flags); - } - } - ap->bcnext = NULL; - bcs->ap = ap; - spin_unlock_irqrestore(&bcs->aplock, flags); - - bcs->rx_bufsize = ap->rp.datablklen; - dev_kfree_skb(bcs->rx_skb); - gigaset_new_rx_skb(bcs); - bcs->chstate |= CHS_NOTIFY_LL; - - /* check/encode B channel protocol */ - if (cmsg->BProtocol == CAPI_DEFAULT) { - bcs->proto2 = L2_HDLC; - dev_warn(cs->dev, - "B2 Protocol X.75 SLP unsupported, using Transparent\n"); - } else { - switch (cmsg->B1protocol) { - case 0: - bcs->proto2 = L2_HDLC; - break; - case 1: - bcs->proto2 = L2_VOICE; - break; - default: - dev_warn(cs->dev, - "B1 Protocol %u unsupported, using Transparent\n", - cmsg->B1protocol); - bcs->proto2 = L2_VOICE; - } - if (cmsg->B2protocol != 1) - dev_warn(cs->dev, - "B2 Protocol %u unsupported, using Transparent\n", - cmsg->B2protocol); - if (cmsg->B3protocol != 0) - dev_warn(cs->dev, - "B3 Protocol %u unsupported, using Transparent\n", - cmsg->B3protocol); - ignore_cstruct_param(cs, cmsg->B1configuration, - "CONNECT_RESP", "B1 Configuration"); - ignore_cstruct_param(cs, cmsg->B2configuration, - "CONNECT_RESP", "B2 Configuration"); - ignore_cstruct_param(cs, cmsg->B3configuration, - "CONNECT_RESP", "B3 Configuration"); - } - - /* ToDo: check/encode remaining parameters */ - ignore_cstruct_param(cs, cmsg->ConnectedNumber, - "CONNECT_RESP", "Connected Number"); - ignore_cstruct_param(cs, cmsg->ConnectedSubaddress, - "CONNECT_RESP", "Connected Subaddress"); - ignore_cstruct_param(cs, cmsg->LLC, - "CONNECT_RESP", "LLC"); - if (cmsg->AdditionalInfo != CAPI_DEFAULT) { - ignore_cstruct_param(cs, cmsg->BChannelinformation, - "CONNECT_RESP", "BChannel Information"); - ignore_cstruct_param(cs, cmsg->Keypadfacility, - "CONNECT_RESP", "Keypad Facility"); - ignore_cstruct_param(cs, cmsg->Useruserdata, - "CONNECT_RESP", "User-User Data"); - ignore_cstruct_param(cs, cmsg->Facilitydataarray, - "CONNECT_RESP", "Facility Data Array"); - } - - /* Accept call */ - if (!gigaset_add_event(cs, &cs->bcs[channel - 1].at_state, - EV_ACCEPT, NULL, 0, NULL)) - return; - gigaset_schedule_event(cs); - return; - - case 1: /* Ignore */ - /* send DISCONNECT_IND to this application */ - send_disconnect_ind(bcs, ap, 0); - - /* remove it from the list of listening apps */ - spin_lock_irqsave(&bcs->aplock, flags); - if (bcs->ap == ap) { - bcs->ap = ap->bcnext; - if (bcs->ap == NULL) { - /* last one: stop ev-layer hupD notifications */ - bcs->apconnstate = APCONN_NONE; - bcs->chstate &= ~CHS_NOTIFY_LL; - } - spin_unlock_irqrestore(&bcs->aplock, flags); - return; - } - for (oap = bcs->ap; oap != NULL; oap = oap->bcnext) { - if (oap->bcnext == ap) { - oap->bcnext = oap->bcnext->bcnext; - spin_unlock_irqrestore(&bcs->aplock, flags); - return; - } - } - spin_unlock_irqrestore(&bcs->aplock, flags); - dev_err(cs->dev, "%s: application %u not found\n", - __func__, ap->id); - return; - - default: /* Reject */ - /* drop all competing applications, keep only this one */ - spin_lock_irqsave(&bcs->aplock, flags); - while (bcs->ap != NULL) { - oap = bcs->ap; - bcs->ap = oap->bcnext; - if (oap != ap) { - spin_unlock_irqrestore(&bcs->aplock, flags); - send_disconnect_ind(bcs, oap, - CapiCallGivenToOtherApplication); - spin_lock_irqsave(&bcs->aplock, flags); - } - } - ap->bcnext = NULL; - bcs->ap = ap; - spin_unlock_irqrestore(&bcs->aplock, flags); - - /* reject call - will trigger DISCONNECT_IND for this app */ - dev_info(cs->dev, "%s: Reject=%x\n", - "CONNECT_RESP", cmsg->Reject); - if (!gigaset_add_event(cs, &cs->bcs[channel - 1].at_state, - EV_HUP, NULL, 0, NULL)) - return; - gigaset_schedule_event(cs); - return; - } -} - -/* - * process CONNECT_B3_REQ message - * build NCCI and emit CONNECT_B3_CONF reply - */ -static void do_connect_b3_req(struct gigaset_capi_ctr *iif, - struct gigaset_capi_appl *ap, - struct sk_buff *skb) -{ - struct cardstate *cs = iif->ctr.driverdata; - _cmsg *cmsg = &iif->acmsg; - struct bc_state *bcs; - int channel; - - /* decode message */ - if (capi_message2cmsg(cmsg, skb->data)) { - dev_err(cs->dev, "%s: message parser failure\n", __func__); - dev_kfree_skb_any(skb); - return; - } - dump_cmsg(DEBUG_CMD, __func__, cmsg); - - /* extract and check channel number from PLCI */ - channel = (cmsg->adr.adrPLCI >> 8) & 0xff; - if (!channel || channel > cs->channels) { - dev_notice(cs->dev, "%s: invalid %s 0x%02x\n", - "CONNECT_B3_REQ", "PLCI", cmsg->adr.adrPLCI); - send_conf(iif, ap, skb, CapiIllContrPlciNcci); - return; - } - bcs = &cs->bcs[channel - 1]; - - /* mark logical connection active */ - bcs->apconnstate = APCONN_ACTIVE; - - /* build NCCI: always 1 (one B3 connection only) */ - cmsg->adr.adrNCCI |= 1 << 16; - - /* NCPI parameter: not applicable for B3 Transparent */ - ignore_cstruct_param(cs, cmsg->NCPI, "CONNECT_B3_REQ", "NCPI"); - send_conf(iif, ap, skb, - (cmsg->NCPI && cmsg->NCPI[0]) ? - CapiNcpiNotSupportedByProtocol : CapiSuccess); -} - -/* - * process CONNECT_B3_RESP message - * Depending on the Reject parameter, either emit CONNECT_B3_ACTIVE_IND - * or queue EV_HUP and emit DISCONNECT_B3_IND. - * The emitted message is always shorter than the received one, - * allowing to reuse the skb. - */ -static void do_connect_b3_resp(struct gigaset_capi_ctr *iif, - struct gigaset_capi_appl *ap, - struct sk_buff *skb) -{ - struct cardstate *cs = iif->ctr.driverdata; - _cmsg *cmsg = &iif->acmsg; - struct bc_state *bcs; - int channel; - unsigned int msgsize; - u8 command; - - /* decode message */ - if (capi_message2cmsg(cmsg, skb->data)) { - dev_err(cs->dev, "%s: message parser failure\n", __func__); - dev_kfree_skb_any(skb); - return; - } - dump_cmsg(DEBUG_CMD, __func__, cmsg); - - /* extract and check channel number and NCCI */ - channel = (cmsg->adr.adrNCCI >> 8) & 0xff; - if (!channel || channel > cs->channels || - ((cmsg->adr.adrNCCI >> 16) & 0xffff) != 1) { - dev_notice(cs->dev, "%s: invalid %s 0x%02x\n", - "CONNECT_B3_RESP", "NCCI", cmsg->adr.adrNCCI); - dev_kfree_skb_any(skb); - return; - } - bcs = &cs->bcs[channel - 1]; - - if (cmsg->Reject) { - /* Reject: clear B3 connect received flag */ - bcs->apconnstate = APCONN_SETUP; - - /* trigger hangup, causing eventual DISCONNECT_IND */ - if (!gigaset_add_event(cs, &bcs->at_state, - EV_HUP, NULL, 0, NULL)) { - dev_kfree_skb_any(skb); - return; - } - gigaset_schedule_event(cs); - - /* emit DISCONNECT_B3_IND */ - command = CAPI_DISCONNECT_B3; - msgsize = CAPI_DISCONNECT_B3_IND_BASELEN; - } else { - /* - * Accept: emit CONNECT_B3_ACTIVE_IND immediately, as - * we only send CONNECT_B3_IND if the B channel is up - */ - command = CAPI_CONNECT_B3_ACTIVE; - msgsize = CAPI_CONNECT_B3_ACTIVE_IND_BASELEN; - } - capi_cmsg_header(cmsg, ap->id, command, CAPI_IND, - ap->nextMessageNumber++, cmsg->adr.adrNCCI); - __skb_trim(skb, msgsize); - if (capi_cmsg2message(cmsg, skb->data)) { - dev_err(cs->dev, "%s: message parser failure\n", __func__); - dev_kfree_skb_any(skb); - return; - } - dump_cmsg(DEBUG_CMD, __func__, cmsg); - capi_ctr_handle_message(&iif->ctr, ap->id, skb); -} - -/* - * process DISCONNECT_REQ message - * schedule EV_HUP and emit DISCONNECT_B3_IND if necessary, - * emit DISCONNECT_CONF reply - */ -static void do_disconnect_req(struct gigaset_capi_ctr *iif, - struct gigaset_capi_appl *ap, - struct sk_buff *skb) -{ - struct cardstate *cs = iif->ctr.driverdata; - _cmsg *cmsg = &iif->acmsg; - struct bc_state *bcs; - _cmsg *b3cmsg; - struct sk_buff *b3skb; - int channel; - - /* decode message */ - if (capi_message2cmsg(cmsg, skb->data)) { - dev_err(cs->dev, "%s: message parser failure\n", __func__); - dev_kfree_skb_any(skb); - return; - } - dump_cmsg(DEBUG_CMD, __func__, cmsg); - - /* extract and check channel number from PLCI */ - channel = (cmsg->adr.adrPLCI >> 8) & 0xff; - if (!channel || channel > cs->channels) { - dev_notice(cs->dev, "%s: invalid %s 0x%02x\n", - "DISCONNECT_REQ", "PLCI", cmsg->adr.adrPLCI); - send_conf(iif, ap, skb, CapiIllContrPlciNcci); - return; - } - bcs = cs->bcs + channel - 1; - - /* ToDo: process parameter: Additional info */ - if (cmsg->AdditionalInfo != CAPI_DEFAULT) { - ignore_cstruct_param(cs, cmsg->BChannelinformation, - "DISCONNECT_REQ", "B Channel Information"); - ignore_cstruct_param(cs, cmsg->Keypadfacility, - "DISCONNECT_REQ", "Keypad Facility"); - ignore_cstruct_param(cs, cmsg->Useruserdata, - "DISCONNECT_REQ", "User-User Data"); - ignore_cstruct_param(cs, cmsg->Facilitydataarray, - "DISCONNECT_REQ", "Facility Data Array"); - } - - /* skip if DISCONNECT_IND already sent */ - if (!bcs->apconnstate) - return; - - /* check for active logical connection */ - if (bcs->apconnstate >= APCONN_ACTIVE) { - /* clear it */ - bcs->apconnstate = APCONN_SETUP; - - /* - * emit DISCONNECT_B3_IND with cause 0x3301 - * use separate cmsg structure, as the content of iif->acmsg - * is still needed for creating the _CONF message - */ - b3cmsg = kmalloc(sizeof(*b3cmsg), GFP_KERNEL); - if (!b3cmsg) { - dev_err(cs->dev, "%s: out of memory\n", __func__); - send_conf(iif, ap, skb, CAPI_MSGOSRESOURCEERR); - return; - } - capi_cmsg_header(b3cmsg, ap->id, CAPI_DISCONNECT_B3, CAPI_IND, - ap->nextMessageNumber++, - cmsg->adr.adrPLCI | (1 << 16)); - b3cmsg->Reason_B3 = CapiProtocolErrorLayer1; - b3skb = alloc_skb(CAPI_DISCONNECT_B3_IND_BASELEN, GFP_KERNEL); - if (b3skb == NULL) { - dev_err(cs->dev, "%s: out of memory\n", __func__); - send_conf(iif, ap, skb, CAPI_MSGOSRESOURCEERR); - kfree(b3cmsg); - return; - } - if (capi_cmsg2message(b3cmsg, - __skb_put(b3skb, CAPI_DISCONNECT_B3_IND_BASELEN))) { - dev_err(cs->dev, "%s: message parser failure\n", - __func__); - kfree(b3cmsg); - dev_kfree_skb_any(b3skb); - return; - } - dump_cmsg(DEBUG_CMD, __func__, b3cmsg); - kfree(b3cmsg); - capi_ctr_handle_message(&iif->ctr, ap->id, b3skb); - } - - /* trigger hangup, causing eventual DISCONNECT_IND */ - if (!gigaset_add_event(cs, &bcs->at_state, EV_HUP, NULL, 0, NULL)) { - send_conf(iif, ap, skb, CAPI_MSGOSRESOURCEERR); - return; - } - gigaset_schedule_event(cs); - - /* emit reply */ - send_conf(iif, ap, skb, CapiSuccess); -} - -/* - * process DISCONNECT_B3_REQ message - * schedule EV_HUP and emit DISCONNECT_B3_CONF reply - */ -static void do_disconnect_b3_req(struct gigaset_capi_ctr *iif, - struct gigaset_capi_appl *ap, - struct sk_buff *skb) -{ - struct cardstate *cs = iif->ctr.driverdata; - _cmsg *cmsg = &iif->acmsg; - struct bc_state *bcs; - int channel; - - /* decode message */ - if (capi_message2cmsg(cmsg, skb->data)) { - dev_err(cs->dev, "%s: message parser failure\n", __func__); - dev_kfree_skb_any(skb); - return; - } - dump_cmsg(DEBUG_CMD, __func__, cmsg); - - /* extract and check channel number and NCCI */ - channel = (cmsg->adr.adrNCCI >> 8) & 0xff; - if (!channel || channel > cs->channels || - ((cmsg->adr.adrNCCI >> 16) & 0xffff) != 1) { - dev_notice(cs->dev, "%s: invalid %s 0x%02x\n", - "DISCONNECT_B3_REQ", "NCCI", cmsg->adr.adrNCCI); - send_conf(iif, ap, skb, CapiIllContrPlciNcci); - return; - } - bcs = &cs->bcs[channel - 1]; - - /* reject if logical connection not active */ - if (bcs->apconnstate < APCONN_ACTIVE) { - send_conf(iif, ap, skb, - CapiMessageNotSupportedInCurrentState); - return; - } - - /* trigger hangup, causing eventual DISCONNECT_B3_IND */ - if (!gigaset_add_event(cs, &bcs->at_state, EV_HUP, NULL, 0, NULL)) { - send_conf(iif, ap, skb, CAPI_MSGOSRESOURCEERR); - return; - } - gigaset_schedule_event(cs); - - /* NCPI parameter: not applicable for B3 Transparent */ - ignore_cstruct_param(cs, cmsg->NCPI, - "DISCONNECT_B3_REQ", "NCPI"); - send_conf(iif, ap, skb, - (cmsg->NCPI && cmsg->NCPI[0]) ? - CapiNcpiNotSupportedByProtocol : CapiSuccess); -} - -/* - * process DATA_B3_REQ message - */ -static void do_data_b3_req(struct gigaset_capi_ctr *iif, - struct gigaset_capi_appl *ap, - struct sk_buff *skb) -{ - struct cardstate *cs = iif->ctr.driverdata; - struct bc_state *bcs; - int channel = CAPIMSG_PLCI_PART(skb->data); - u16 ncci = CAPIMSG_NCCI_PART(skb->data); - u16 msglen = CAPIMSG_LEN(skb->data); - u16 datalen = CAPIMSG_DATALEN(skb->data); - u16 flags = CAPIMSG_FLAGS(skb->data); - u16 msgid = CAPIMSG_MSGID(skb->data); - u16 handle = CAPIMSG_HANDLE_REQ(skb->data); - - /* frequent message, avoid _cmsg overhead */ - dump_rawmsg(DEBUG_MCMD, __func__, skb->data); - - /* check parameters */ - if (channel == 0 || channel > cs->channels || ncci != 1) { - dev_notice(cs->dev, "%s: invalid %s 0x%02x\n", - "DATA_B3_REQ", "NCCI", CAPIMSG_NCCI(skb->data)); - send_conf(iif, ap, skb, CapiIllContrPlciNcci); - return; - } - bcs = &cs->bcs[channel - 1]; - if (msglen != CAPI_DATA_B3_REQ_LEN && msglen != CAPI_DATA_B3_REQ_LEN64) - dev_notice(cs->dev, "%s: unexpected length %d\n", - "DATA_B3_REQ", msglen); - if (msglen + datalen != skb->len) - dev_notice(cs->dev, "%s: length mismatch (%d+%d!=%d)\n", - "DATA_B3_REQ", msglen, datalen, skb->len); - if (msglen + datalen > skb->len) { - /* message too short for announced data length */ - send_conf(iif, ap, skb, CapiIllMessageParmCoding); /* ? */ - return; - } - if (flags & CAPI_FLAGS_RESERVED) { - dev_notice(cs->dev, "%s: reserved flags set (%x)\n", - "DATA_B3_REQ", flags); - send_conf(iif, ap, skb, CapiIllMessageParmCoding); - return; - } - - /* reject if logical connection not active */ - if (bcs->apconnstate < APCONN_ACTIVE) { - send_conf(iif, ap, skb, CapiMessageNotSupportedInCurrentState); - return; - } - - /* pull CAPI message into link layer header */ - skb_reset_mac_header(skb); - skb->mac_len = msglen; - skb_pull(skb, msglen); - - /* pass to device-specific module */ - if (cs->ops->send_skb(bcs, skb) < 0) { - send_conf(iif, ap, skb, CAPI_MSGOSRESOURCEERR); - return; - } - - /* - * DATA_B3_CONF will be sent by gigaset_skb_sent() only if "delivery - * confirmation" bit is set; otherwise we have to send it now - */ - if (!(flags & CAPI_FLAGS_DELIVERY_CONFIRMATION)) - send_data_b3_conf(cs, &iif->ctr, ap->id, msgid, channel, handle, - flags ? CapiFlagsNotSupportedByProtocol - : CAPI_NOERROR); -} - -/* - * process RESET_B3_REQ message - * just always reply "not supported by current protocol" - */ -static void do_reset_b3_req(struct gigaset_capi_ctr *iif, - struct gigaset_capi_appl *ap, - struct sk_buff *skb) -{ - struct cardstate *cs = iif->ctr.driverdata; - - /* decode message */ - if (capi_message2cmsg(&iif->acmsg, skb->data)) { - dev_err(cs->dev, "%s: message parser failure\n", __func__); - dev_kfree_skb_any(skb); - return; - } - dump_cmsg(DEBUG_CMD, __func__, &iif->acmsg); - send_conf(iif, ap, skb, - CapiResetProcedureNotSupportedByCurrentProtocol); -} - -/* - * unsupported CAPI message handler - */ -static void do_unsupported(struct gigaset_capi_ctr *iif, - struct gigaset_capi_appl *ap, - struct sk_buff *skb) -{ - struct cardstate *cs = iif->ctr.driverdata; - - /* decode message */ - if (capi_message2cmsg(&iif->acmsg, skb->data)) { - dev_err(cs->dev, "%s: message parser failure\n", __func__); - dev_kfree_skb_any(skb); - return; - } - dump_cmsg(DEBUG_CMD, __func__, &iif->acmsg); - send_conf(iif, ap, skb, CapiMessageNotSupportedInCurrentState); -} - -/* - * CAPI message handler: no-op - */ -static void do_nothing(struct gigaset_capi_ctr *iif, - struct gigaset_capi_appl *ap, - struct sk_buff *skb) -{ - struct cardstate *cs = iif->ctr.driverdata; - - /* decode message */ - if (capi_message2cmsg(&iif->acmsg, skb->data)) { - dev_err(cs->dev, "%s: message parser failure\n", __func__); - dev_kfree_skb_any(skb); - return; - } - dump_cmsg(DEBUG_CMD, __func__, &iif->acmsg); - dev_kfree_skb_any(skb); -} - -static void do_data_b3_resp(struct gigaset_capi_ctr *iif, - struct gigaset_capi_appl *ap, - struct sk_buff *skb) -{ - dump_rawmsg(DEBUG_MCMD, __func__, skb->data); - dev_kfree_skb_any(skb); -} - -/* table of outgoing CAPI message handlers with lookup function */ -typedef void (*capi_send_handler_t)(struct gigaset_capi_ctr *, - struct gigaset_capi_appl *, - struct sk_buff *); - -static struct { - u16 cmd; - capi_send_handler_t handler; -} capi_send_handler_table[] = { - /* most frequent messages first for faster lookup */ - { CAPI_DATA_B3_REQ, do_data_b3_req }, - { CAPI_DATA_B3_RESP, do_data_b3_resp }, - - { CAPI_ALERT_REQ, do_alert_req }, - { CAPI_CONNECT_ACTIVE_RESP, do_nothing }, - { CAPI_CONNECT_B3_ACTIVE_RESP, do_nothing }, - { CAPI_CONNECT_B3_REQ, do_connect_b3_req }, - { CAPI_CONNECT_B3_RESP, do_connect_b3_resp }, - { CAPI_CONNECT_B3_T90_ACTIVE_RESP, do_nothing }, - { CAPI_CONNECT_REQ, do_connect_req }, - { CAPI_CONNECT_RESP, do_connect_resp }, - { CAPI_DISCONNECT_B3_REQ, do_disconnect_b3_req }, - { CAPI_DISCONNECT_B3_RESP, do_nothing }, - { CAPI_DISCONNECT_REQ, do_disconnect_req }, - { CAPI_DISCONNECT_RESP, do_nothing }, - { CAPI_FACILITY_REQ, do_facility_req }, - { CAPI_FACILITY_RESP, do_nothing }, - { CAPI_LISTEN_REQ, do_listen_req }, - { CAPI_SELECT_B_PROTOCOL_REQ, do_unsupported }, - { CAPI_RESET_B3_REQ, do_reset_b3_req }, - { CAPI_RESET_B3_RESP, do_nothing }, - - /* - * ToDo: support overlap sending (requires ev-layer state - * machine extension to generate additional ATD commands) - */ - { CAPI_INFO_REQ, do_unsupported }, - { CAPI_INFO_RESP, do_nothing }, - - /* - * ToDo: what's the proper response for these? - */ - { CAPI_MANUFACTURER_REQ, do_nothing }, - { CAPI_MANUFACTURER_RESP, do_nothing }, -}; - -/* look up handler */ -static inline capi_send_handler_t lookup_capi_send_handler(const u16 cmd) -{ - size_t i; - - for (i = 0; i < ARRAY_SIZE(capi_send_handler_table); i++) - if (capi_send_handler_table[i].cmd == cmd) - return capi_send_handler_table[i].handler; - return NULL; -} - - -/** - * gigaset_send_message() - accept a CAPI message from an application - * @ctr: controller descriptor structure. - * @skb: CAPI message. - * - * Return value: CAPI error code - * Note: capidrv (and probably others, too) only uses the return value to - * decide whether it has to free the skb (only if result != CAPI_NOERROR (0)) - */ -static u16 gigaset_send_message(struct capi_ctr *ctr, struct sk_buff *skb) -{ - struct gigaset_capi_ctr *iif - = container_of(ctr, struct gigaset_capi_ctr, ctr); - struct cardstate *cs = ctr->driverdata; - struct gigaset_capi_appl *ap; - capi_send_handler_t handler; - - /* can only handle linear sk_buffs */ - if (skb_linearize(skb) < 0) { - dev_warn(cs->dev, "%s: skb_linearize failed\n", __func__); - return CAPI_MSGOSRESOURCEERR; - } - - /* retrieve application data structure */ - ap = get_appl(iif, CAPIMSG_APPID(skb->data)); - if (!ap) { - dev_notice(cs->dev, "%s: application %u not registered\n", - __func__, CAPIMSG_APPID(skb->data)); - return CAPI_ILLAPPNR; - } - - /* look up command */ - handler = lookup_capi_send_handler(CAPIMSG_CMD(skb->data)); - if (!handler) { - /* unknown/unsupported message type */ - if (printk_ratelimit()) - dev_notice(cs->dev, "%s: unsupported message %u\n", - __func__, CAPIMSG_CMD(skb->data)); - return CAPI_ILLCMDORSUBCMDORMSGTOSMALL; - } - - /* serialize */ - if (atomic_add_return(1, &iif->sendqlen) > 1) { - /* queue behind other messages */ - skb_queue_tail(&iif->sendqueue, skb); - return CAPI_NOERROR; - } - - /* process message */ - handler(iif, ap, skb); - - /* process other messages arrived in the meantime */ - while (atomic_sub_return(1, &iif->sendqlen) > 0) { - skb = skb_dequeue(&iif->sendqueue); - if (!skb) { - /* should never happen */ - dev_err(cs->dev, "%s: send queue empty\n", __func__); - continue; - } - ap = get_appl(iif, CAPIMSG_APPID(skb->data)); - if (!ap) { - /* could that happen? */ - dev_warn(cs->dev, "%s: application %u vanished\n", - __func__, CAPIMSG_APPID(skb->data)); - continue; - } - handler = lookup_capi_send_handler(CAPIMSG_CMD(skb->data)); - if (!handler) { - /* should never happen */ - dev_err(cs->dev, "%s: handler %x vanished\n", - __func__, CAPIMSG_CMD(skb->data)); - continue; - } - handler(iif, ap, skb); - } - - return CAPI_NOERROR; -} - -/** - * gigaset_procinfo() - build single line description for controller - * @ctr: controller descriptor structure. - * - * Return value: pointer to generated string (null terminated) - */ -static char *gigaset_procinfo(struct capi_ctr *ctr) -{ - return ctr->name; /* ToDo: more? */ -} - -static int gigaset_proc_show(struct seq_file *m, void *v) -{ - struct capi_ctr *ctr = m->private; - struct cardstate *cs = ctr->driverdata; - char *s; - int i; - - seq_printf(m, "%-16s %s\n", "name", ctr->name); - seq_printf(m, "%-16s %s %s\n", "dev", - dev_driver_string(cs->dev), dev_name(cs->dev)); - seq_printf(m, "%-16s %d\n", "id", cs->myid); - if (cs->gotfwver) - seq_printf(m, "%-16s %d.%d.%d.%d\n", "firmware", - cs->fwver[0], cs->fwver[1], cs->fwver[2], cs->fwver[3]); - seq_printf(m, "%-16s %d\n", "channels", cs->channels); - seq_printf(m, "%-16s %s\n", "onechannel", cs->onechannel ? "yes" : "no"); - - switch (cs->mode) { - case M_UNKNOWN: - s = "unknown"; - break; - case M_CONFIG: - s = "config"; - break; - case M_UNIMODEM: - s = "Unimodem"; - break; - case M_CID: - s = "CID"; - break; - default: - s = "??"; - } - seq_printf(m, "%-16s %s\n", "mode", s); - - switch (cs->mstate) { - case MS_UNINITIALIZED: - s = "uninitialized"; - break; - case MS_INIT: - s = "init"; - break; - case MS_LOCKED: - s = "locked"; - break; - case MS_SHUTDOWN: - s = "shutdown"; - break; - case MS_RECOVER: - s = "recover"; - break; - case MS_READY: - s = "ready"; - break; - default: - s = "??"; - } - seq_printf(m, "%-16s %s\n", "mstate", s); - - seq_printf(m, "%-16s %s\n", "running", cs->running ? "yes" : "no"); - seq_printf(m, "%-16s %s\n", "connected", cs->connected ? "yes" : "no"); - seq_printf(m, "%-16s %s\n", "isdn_up", cs->isdn_up ? "yes" : "no"); - seq_printf(m, "%-16s %s\n", "cidmode", cs->cidmode ? "yes" : "no"); - - for (i = 0; i < cs->channels; i++) { - seq_printf(m, "[%d]%-13s %d\n", i, "corrupted", - cs->bcs[i].corrupted); - seq_printf(m, "[%d]%-13s %d\n", i, "trans_down", - cs->bcs[i].trans_down); - seq_printf(m, "[%d]%-13s %d\n", i, "trans_up", - cs->bcs[i].trans_up); - seq_printf(m, "[%d]%-13s %d\n", i, "chstate", - cs->bcs[i].chstate); - switch (cs->bcs[i].proto2) { - case L2_BITSYNC: - s = "bitsync"; - break; - case L2_HDLC: - s = "HDLC"; - break; - case L2_VOICE: - s = "voice"; - break; - default: - s = "??"; - } - seq_printf(m, "[%d]%-13s %s\n", i, "proto2", s); - } - return 0; -} - -/** - * gigaset_isdn_regdev() - register device to LL - * @cs: device descriptor structure. - * @isdnid: device name. - * - * Return value: 0 on success, error code < 0 on failure - */ -int gigaset_isdn_regdev(struct cardstate *cs, const char *isdnid) -{ - struct gigaset_capi_ctr *iif; - int rc; - - iif = kzalloc(sizeof(*iif), GFP_KERNEL); - if (!iif) { - pr_err("%s: out of memory\n", __func__); - return -ENOMEM; - } - - /* prepare controller structure */ - iif->ctr.owner = THIS_MODULE; - iif->ctr.driverdata = cs; - strncpy(iif->ctr.name, isdnid, sizeof(iif->ctr.name) - 1); - iif->ctr.driver_name = "gigaset"; - iif->ctr.load_firmware = NULL; - iif->ctr.reset_ctr = NULL; - iif->ctr.register_appl = gigaset_register_appl; - iif->ctr.release_appl = gigaset_release_appl; - iif->ctr.send_message = gigaset_send_message; - iif->ctr.procinfo = gigaset_procinfo; - iif->ctr.proc_show = gigaset_proc_show, - INIT_LIST_HEAD(&iif->appls); - skb_queue_head_init(&iif->sendqueue); - atomic_set(&iif->sendqlen, 0); - - /* register controller with CAPI */ - rc = attach_capi_ctr(&iif->ctr); - if (rc) { - pr_err("attach_capi_ctr failed (%d)\n", rc); - kfree(iif); - return rc; - } - - cs->iif = iif; - cs->hw_hdr_len = CAPI_DATA_B3_REQ_LEN; - return 0; -} - -/** - * gigaset_isdn_unregdev() - unregister device from LL - * @cs: device descriptor structure. - */ -void gigaset_isdn_unregdev(struct cardstate *cs) -{ - struct gigaset_capi_ctr *iif = cs->iif; - - detach_capi_ctr(&iif->ctr); - kfree(iif); - cs->iif = NULL; -} - -static struct capi_driver capi_driver_gigaset = { - .name = "gigaset", - .revision = "1.0", -}; - -/** - * gigaset_isdn_regdrv() - register driver to LL - */ -void gigaset_isdn_regdrv(void) -{ - pr_info("Kernel CAPI interface\n"); - register_capi_driver(&capi_driver_gigaset); -} - -/** - * gigaset_isdn_unregdrv() - unregister driver from LL - */ -void gigaset_isdn_unregdrv(void) -{ - unregister_capi_driver(&capi_driver_gigaset); -} diff --git a/drivers/staging/isdn/gigaset/common.c b/drivers/staging/isdn/gigaset/common.c deleted file mode 100644 index 3bb8092858ab..000000000000 --- a/drivers/staging/isdn/gigaset/common.c +++ /dev/null @@ -1,1153 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -/* - * Stuff used by all variants of the driver - * - * Copyright (c) 2001 by Stefan Eilers, - * Hansjoerg Lipp <hjlipp@web.de>, - * Tilman Schmidt <tilman@imap.cc>. - * - * ===================================================================== - * ===================================================================== - */ - -#include "gigaset.h" -#include <linux/module.h> -#include <linux/moduleparam.h> - -/* Version Information */ -#define DRIVER_AUTHOR "Hansjoerg Lipp <hjlipp@web.de>, Tilman Schmidt <tilman@imap.cc>, Stefan Eilers" -#define DRIVER_DESC "Driver for Gigaset 307x" - -#ifdef CONFIG_GIGASET_DEBUG -#define DRIVER_DESC_DEBUG " (debug build)" -#else -#define DRIVER_DESC_DEBUG "" -#endif - -/* Module parameters */ -int gigaset_debuglevel; -EXPORT_SYMBOL_GPL(gigaset_debuglevel); -module_param_named(debug, gigaset_debuglevel, int, S_IRUGO | S_IWUSR); -MODULE_PARM_DESC(debug, "debug level"); - -/* driver state flags */ -#define VALID_MINOR 0x01 -#define VALID_ID 0x02 - -/** - * gigaset_dbg_buffer() - dump data in ASCII and hex for debugging - * @level: debugging level. - * @msg: message prefix. - * @len: number of bytes to dump. - * @buf: data to dump. - * - * If the current debugging level includes one of the bits set in @level, - * @len bytes starting at @buf are logged to dmesg at KERN_DEBUG prio, - * prefixed by the text @msg. - */ -void gigaset_dbg_buffer(enum debuglevel level, const unsigned char *msg, - size_t len, const unsigned char *buf) -{ - unsigned char outbuf[80]; - unsigned char c; - size_t space = sizeof outbuf - 1; - unsigned char *out = outbuf; - size_t numin = len; - - while (numin--) { - c = *buf++; - if (c == '~' || c == '^' || c == '\\') { - if (!space--) - break; - *out++ = '\\'; - } - if (c & 0x80) { - if (!space--) - break; - *out++ = '~'; - c ^= 0x80; - } - if (c < 0x20 || c == 0x7f) { - if (!space--) - break; - *out++ = '^'; - c ^= 0x40; - } - if (!space--) - break; - *out++ = c; - } - *out = 0; - - gig_dbg(level, "%s (%u bytes): %s", msg, (unsigned) len, outbuf); -} -EXPORT_SYMBOL_GPL(gigaset_dbg_buffer); - -static int setflags(struct cardstate *cs, unsigned flags, unsigned delay) -{ - int r; - - r = cs->ops->set_modem_ctrl(cs, cs->control_state, flags); - cs->control_state = flags; - if (r < 0) - return r; - - if (delay) { - set_current_state(TASK_INTERRUPTIBLE); - schedule_timeout(delay * HZ / 1000); - } - - return 0; -} - -int gigaset_enterconfigmode(struct cardstate *cs) -{ - int i, r; - - cs->control_state = TIOCM_RTS; - - r = setflags(cs, TIOCM_DTR, 200); - if (r < 0) - goto error; - r = setflags(cs, 0, 200); - if (r < 0) - goto error; - for (i = 0; i < 5; ++i) { - r = setflags(cs, TIOCM_RTS, 100); - if (r < 0) - goto error; - r = setflags(cs, 0, 100); - if (r < 0) - goto error; - } - r = setflags(cs, TIOCM_RTS | TIOCM_DTR, 800); - if (r < 0) - goto error; - - return 0; - -error: - dev_err(cs->dev, "error %d on setuartbits\n", -r); - cs->control_state = TIOCM_RTS | TIOCM_DTR; - cs->ops->set_modem_ctrl(cs, 0, TIOCM_RTS | TIOCM_DTR); - - return -1; -} - -static int test_timeout(struct at_state_t *at_state) -{ - if (!at_state->timer_expires) - return 0; - - if (--at_state->timer_expires) { - gig_dbg(DEBUG_MCMD, "decreased timer of %p to %lu", - at_state, at_state->timer_expires); - return 0; - } - - gigaset_add_event(at_state->cs, at_state, EV_TIMEOUT, NULL, - at_state->timer_index, NULL); - return 1; -} - -static void timer_tick(struct timer_list *t) -{ - struct cardstate *cs = from_timer(cs, t, timer); - unsigned long flags; - unsigned channel; - struct at_state_t *at_state; - int timeout = 0; - - spin_lock_irqsave(&cs->lock, flags); - - for (channel = 0; channel < cs->channels; ++channel) - if (test_timeout(&cs->bcs[channel].at_state)) - timeout = 1; - - if (test_timeout(&cs->at_state)) - timeout = 1; - - list_for_each_entry(at_state, &cs->temp_at_states, list) - if (test_timeout(at_state)) - timeout = 1; - - if (cs->running) { - mod_timer(&cs->timer, jiffies + msecs_to_jiffies(GIG_TICK)); - if (timeout) { - gig_dbg(DEBUG_EVENT, "scheduling timeout"); - tasklet_schedule(&cs->event_tasklet); - } - } - - spin_unlock_irqrestore(&cs->lock, flags); -} - -int gigaset_get_channel(struct bc_state *bcs) -{ - unsigned long flags; - - spin_lock_irqsave(&bcs->cs->lock, flags); - if (bcs->use_count || !try_module_get(bcs->cs->driver->owner)) { - gig_dbg(DEBUG_CHANNEL, "could not allocate channel %d", - bcs->channel); - spin_unlock_irqrestore(&bcs->cs->lock, flags); - return -EBUSY; - } - ++bcs->use_count; - bcs->busy = 1; - gig_dbg(DEBUG_CHANNEL, "allocated channel %d", bcs->channel); - spin_unlock_irqrestore(&bcs->cs->lock, flags); - return 0; -} - -struct bc_state *gigaset_get_free_channel(struct cardstate *cs) -{ - unsigned long flags; - int i; - - spin_lock_irqsave(&cs->lock, flags); - if (!try_module_get(cs->driver->owner)) { - gig_dbg(DEBUG_CHANNEL, - "could not get module for allocating channel"); - spin_unlock_irqrestore(&cs->lock, flags); - return NULL; - } - for (i = 0; i < cs->channels; ++i) - if (!cs->bcs[i].use_count) { - ++cs->bcs[i].use_count; - cs->bcs[i].busy = 1; - spin_unlock_irqrestore(&cs->lock, flags); - gig_dbg(DEBUG_CHANNEL, "allocated channel %d", i); - return cs->bcs + i; - } - module_put(cs->driver->owner); - spin_unlock_irqrestore(&cs->lock, flags); - gig_dbg(DEBUG_CHANNEL, "no free channel"); - return NULL; -} - -void gigaset_free_channel(struct bc_state *bcs) -{ - unsigned long flags; - - spin_lock_irqsave(&bcs->cs->lock, flags); - if (!bcs->busy) { - gig_dbg(DEBUG_CHANNEL, "could not free channel %d", - bcs->channel); - spin_unlock_irqrestore(&bcs->cs->lock, flags); - return; - } - --bcs->use_count; - bcs->busy = 0; - module_put(bcs->cs->driver->owner); - gig_dbg(DEBUG_CHANNEL, "freed channel %d", bcs->channel); - spin_unlock_irqrestore(&bcs->cs->lock, flags); -} - -int gigaset_get_channels(struct cardstate *cs) -{ - unsigned long flags; - int i; - - spin_lock_irqsave(&cs->lock, flags); - for (i = 0; i < cs->channels; ++i) - if (cs->bcs[i].use_count) { - spin_unlock_irqrestore(&cs->lock, flags); - gig_dbg(DEBUG_CHANNEL, - "could not allocate all channels"); - return -EBUSY; - } - for (i = 0; i < cs->channels; ++i) - ++cs->bcs[i].use_count; - spin_unlock_irqrestore(&cs->lock, flags); - - gig_dbg(DEBUG_CHANNEL, "allocated all channels"); - - return 0; -} - -void gigaset_free_channels(struct cardstate *cs) -{ - unsigned long flags; - int i; - - gig_dbg(DEBUG_CHANNEL, "unblocking all channels"); - spin_lock_irqsave(&cs->lock, flags); - for (i = 0; i < cs->channels; ++i) - --cs->bcs[i].use_count; - spin_unlock_irqrestore(&cs->lock, flags); -} - -void gigaset_block_channels(struct cardstate *cs) -{ - unsigned long flags; - int i; - - gig_dbg(DEBUG_CHANNEL, "blocking all channels"); - spin_lock_irqsave(&cs->lock, flags); - for (i = 0; i < cs->channels; ++i) - ++cs->bcs[i].use_count; - spin_unlock_irqrestore(&cs->lock, flags); -} - -static void clear_events(struct cardstate *cs) -{ - struct event_t *ev; - unsigned head, tail; - unsigned long flags; - - spin_lock_irqsave(&cs->ev_lock, flags); - - head = cs->ev_head; - tail = cs->ev_tail; - - while (tail != head) { - ev = cs->events + head; - kfree(ev->ptr); - head = (head + 1) % MAX_EVENTS; - } - - cs->ev_head = tail; - - spin_unlock_irqrestore(&cs->ev_lock, flags); -} - -/** - * gigaset_add_event() - add event to device event queue - * @cs: device descriptor structure. - * @at_state: connection state structure. - * @type: event type. - * @ptr: pointer parameter for event. - * @parameter: integer parameter for event. - * @arg: pointer parameter for event. - * - * Allocate an event queue entry from the device's event queue, and set it up - * with the parameters given. - * - * Return value: added event - */ -struct event_t *gigaset_add_event(struct cardstate *cs, - struct at_state_t *at_state, int type, - void *ptr, int parameter, void *arg) -{ - unsigned long flags; - unsigned next, tail; - struct event_t *event = NULL; - - gig_dbg(DEBUG_EVENT, "queueing event %d", type); - - spin_lock_irqsave(&cs->ev_lock, flags); - - tail = cs->ev_tail; - next = (tail + 1) % MAX_EVENTS; - if (unlikely(next == cs->ev_head)) - dev_err(cs->dev, "event queue full\n"); - else { - event = cs->events + tail; - event->type = type; - event->at_state = at_state; - event->cid = -1; - event->ptr = ptr; - event->arg = arg; - event->parameter = parameter; - cs->ev_tail = next; - } - - spin_unlock_irqrestore(&cs->ev_lock, flags); - - return event; -} -EXPORT_SYMBOL_GPL(gigaset_add_event); - -static void clear_at_state(struct at_state_t *at_state) -{ - int i; - - for (i = 0; i < STR_NUM; ++i) { - kfree(at_state->str_var[i]); - at_state->str_var[i] = NULL; - } -} - -static void dealloc_temp_at_states(struct cardstate *cs) -{ - struct at_state_t *cur, *next; - - list_for_each_entry_safe(cur, next, &cs->temp_at_states, list) { - list_del(&cur->list); - clear_at_state(cur); - kfree(cur); - } -} - -static void gigaset_freebcs(struct bc_state *bcs) -{ - int i; - - gig_dbg(DEBUG_INIT, "freeing bcs[%d]->hw", bcs->channel); - bcs->cs->ops->freebcshw(bcs); - - gig_dbg(DEBUG_INIT, "clearing bcs[%d]->at_state", bcs->channel); - clear_at_state(&bcs->at_state); - gig_dbg(DEBUG_INIT, "freeing bcs[%d]->skb", bcs->channel); - dev_kfree_skb(bcs->rx_skb); - bcs->rx_skb = NULL; - - for (i = 0; i < AT_NUM; ++i) { - kfree(bcs->commands[i]); - bcs->commands[i] = NULL; - } -} - -static struct cardstate *alloc_cs(struct gigaset_driver *drv) -{ - unsigned long flags; - unsigned i; - struct cardstate *cs; - struct cardstate *ret = NULL; - - spin_lock_irqsave(&drv->lock, flags); - if (drv->blocked) - goto exit; - for (i = 0; i < drv->minors; ++i) { - cs = drv->cs + i; - if (!(cs->flags & VALID_MINOR)) { - cs->flags = VALID_MINOR; - ret = cs; - break; - } - } -exit: - spin_unlock_irqrestore(&drv->lock, flags); - return ret; -} - -static void free_cs(struct cardstate *cs) -{ - cs->flags = 0; -} - -static void make_valid(struct cardstate *cs, unsigned mask) -{ - unsigned long flags; - struct gigaset_driver *drv = cs->driver; - spin_lock_irqsave(&drv->lock, flags); - cs->flags |= mask; - spin_unlock_irqrestore(&drv->lock, flags); -} - -static void make_invalid(struct cardstate *cs, unsigned mask) -{ - unsigned long flags; - struct gigaset_driver *drv = cs->driver; - spin_lock_irqsave(&drv->lock, flags); - cs->flags &= ~mask; - spin_unlock_irqrestore(&drv->lock, flags); -} - -/** - * gigaset_freecs() - free all associated ressources of a device - * @cs: device descriptor structure. - * - * Stops all tasklets and timers, unregisters the device from all - * subsystems it was registered to, deallocates the device structure - * @cs and all structures referenced from it. - * Operations on the device should be stopped before calling this. - */ -void gigaset_freecs(struct cardstate *cs) -{ - int i; - unsigned long flags; - - if (!cs) - return; - - mutex_lock(&cs->mutex); - - spin_lock_irqsave(&cs->lock, flags); - cs->running = 0; - spin_unlock_irqrestore(&cs->lock, flags); /* event handler and timer are - not rescheduled below */ - - tasklet_kill(&cs->event_tasklet); - del_timer_sync(&cs->timer); - - switch (cs->cs_init) { - default: - /* clear B channel structures */ - for (i = 0; i < cs->channels; ++i) { - gig_dbg(DEBUG_INIT, "clearing bcs[%d]", i); - gigaset_freebcs(cs->bcs + i); - } - - /* clear device sysfs */ - gigaset_free_dev_sysfs(cs); - - gigaset_if_free(cs); - - gig_dbg(DEBUG_INIT, "clearing hw"); - cs->ops->freecshw(cs); - - /* fall through */ - case 2: /* error in initcshw */ - /* Deregister from LL */ - make_invalid(cs, VALID_ID); - gigaset_isdn_unregdev(cs); - - /* fall through */ - case 1: /* error when registering to LL */ - gig_dbg(DEBUG_INIT, "clearing at_state"); - clear_at_state(&cs->at_state); - dealloc_temp_at_states(cs); - clear_events(cs); - tty_port_destroy(&cs->port); - - /* fall through */ - case 0: /* error in basic setup */ - gig_dbg(DEBUG_INIT, "freeing inbuf"); - kfree(cs->inbuf); - kfree(cs->bcs); - } - - mutex_unlock(&cs->mutex); - free_cs(cs); -} -EXPORT_SYMBOL_GPL(gigaset_freecs); - -void gigaset_at_init(struct at_state_t *at_state, struct bc_state *bcs, - struct cardstate *cs, int cid) -{ - int i; - - INIT_LIST_HEAD(&at_state->list); - at_state->waiting = 0; - at_state->getstring = 0; - at_state->pending_commands = 0; - at_state->timer_expires = 0; - at_state->timer_active = 0; - at_state->timer_index = 0; - at_state->seq_index = 0; - at_state->ConState = 0; - for (i = 0; i < STR_NUM; ++i) - at_state->str_var[i] = NULL; - at_state->int_var[VAR_ZDLE] = 0; - at_state->int_var[VAR_ZCTP] = -1; - at_state->int_var[VAR_ZSAU] = ZSAU_NULL; - at_state->cs = cs; - at_state->bcs = bcs; - at_state->cid = cid; - if (!cid) - at_state->replystruct = cs->tabnocid; - else - at_state->replystruct = cs->tabcid; -} - - -static void gigaset_inbuf_init(struct inbuf_t *inbuf, struct cardstate *cs) -/* inbuf->read must be allocated before! */ -{ - inbuf->head = 0; - inbuf->tail = 0; - inbuf->cs = cs; - inbuf->inputstate = INS_command; -} - -/** - * gigaset_fill_inbuf() - append received data to input buffer - * @inbuf: buffer structure. - * @src: received data. - * @numbytes: number of bytes received. - * - * Return value: !=0 if some data was appended - */ -int gigaset_fill_inbuf(struct inbuf_t *inbuf, const unsigned char *src, - unsigned numbytes) -{ - unsigned n, head, tail, bytesleft; - - gig_dbg(DEBUG_INTR, "received %u bytes", numbytes); - - if (!numbytes) - return 0; - - bytesleft = numbytes; - tail = inbuf->tail; - head = inbuf->head; - gig_dbg(DEBUG_INTR, "buffer state: %u -> %u", head, tail); - - while (bytesleft) { - if (head > tail) - n = head - 1 - tail; - else if (head == 0) - n = (RBUFSIZE - 1) - tail; - else - n = RBUFSIZE - tail; - if (!n) { - dev_err(inbuf->cs->dev, - "buffer overflow (%u bytes lost)\n", - bytesleft); - break; - } - if (n > bytesleft) - n = bytesleft; - memcpy(inbuf->data + tail, src, n); - bytesleft -= n; - tail = (tail + n) % RBUFSIZE; - src += n; - } - gig_dbg(DEBUG_INTR, "setting tail to %u", tail); - inbuf->tail = tail; - return numbytes != bytesleft; -} -EXPORT_SYMBOL_GPL(gigaset_fill_inbuf); - -/* Initialize the b-channel structure */ -static int gigaset_initbcs(struct bc_state *bcs, struct cardstate *cs, - int channel) -{ - int i; - - bcs->tx_skb = NULL; - - skb_queue_head_init(&bcs->squeue); - - bcs->corrupted = 0; - bcs->trans_down = 0; - bcs->trans_up = 0; - - gig_dbg(DEBUG_INIT, "setting up bcs[%d]->at_state", channel); - gigaset_at_init(&bcs->at_state, bcs, cs, -1); - -#ifdef CONFIG_GIGASET_DEBUG - bcs->emptycount = 0; -#endif - - bcs->rx_bufsize = 0; - bcs->rx_skb = NULL; - bcs->rx_fcs = PPP_INITFCS; - bcs->inputstate = 0; - bcs->channel = channel; - bcs->cs = cs; - - bcs->chstate = 0; - bcs->use_count = 1; - bcs->busy = 0; - bcs->ignore = cs->ignoreframes; - - for (i = 0; i < AT_NUM; ++i) - bcs->commands[i] = NULL; - - spin_lock_init(&bcs->aplock); - bcs->ap = NULL; - bcs->apconnstate = 0; - - gig_dbg(DEBUG_INIT, " setting up bcs[%d]->hw", channel); - return cs->ops->initbcshw(bcs); -} - -/** - * gigaset_initcs() - initialize device structure - * @drv: hardware driver the device belongs to - * @channels: number of B channels supported by device - * @onechannel: !=0 if B channel data and AT commands share one - * communication channel (M10x), - * ==0 if B channels have separate communication channels (base) - * @ignoreframes: number of frames to ignore after setting up B channel - * @cidmode: !=0: start in CallID mode - * @modulename: name of driver module for LL registration - * - * Allocate and initialize cardstate structure for Gigaset driver - * Calls hardware dependent gigaset_initcshw() function - * Calls B channel initialization function gigaset_initbcs() for each B channel - * - * Return value: - * pointer to cardstate structure - */ -struct cardstate *gigaset_initcs(struct gigaset_driver *drv, int channels, - int onechannel, int ignoreframes, - int cidmode, const char *modulename) -{ - struct cardstate *cs; - unsigned long flags; - int i; - - gig_dbg(DEBUG_INIT, "allocating cs"); - cs = alloc_cs(drv); - if (!cs) { - pr_err("maximum number of devices exceeded\n"); - return NULL; - } - - cs->cs_init = 0; - cs->channels = channels; - cs->onechannel = onechannel; - cs->ignoreframes = ignoreframes; - INIT_LIST_HEAD(&cs->temp_at_states); - cs->running = 0; - timer_setup(&cs->timer, timer_tick, 0); - spin_lock_init(&cs->ev_lock); - cs->ev_tail = 0; - cs->ev_head = 0; - - tasklet_init(&cs->event_tasklet, gigaset_handle_event, - (unsigned long) cs); - tty_port_init(&cs->port); - cs->commands_pending = 0; - cs->cur_at_seq = 0; - cs->gotfwver = -1; - cs->dev = NULL; - cs->tty_dev = NULL; - cs->cidmode = cidmode != 0; - cs->tabnocid = gigaset_tab_nocid; - cs->tabcid = gigaset_tab_cid; - - init_waitqueue_head(&cs->waitqueue); - cs->waiting = 0; - - cs->mode = M_UNKNOWN; - cs->mstate = MS_UNINITIALIZED; - - cs->bcs = kmalloc_array(channels, sizeof(struct bc_state), GFP_KERNEL); - cs->inbuf = kmalloc(sizeof(struct inbuf_t), GFP_KERNEL); - if (!cs->bcs || !cs->inbuf) { - pr_err("out of memory\n"); - goto error; - } - ++cs->cs_init; - - gig_dbg(DEBUG_INIT, "setting up at_state"); - spin_lock_init(&cs->lock); - gigaset_at_init(&cs->at_state, NULL, cs, 0); - cs->dle = 0; - cs->cbytes = 0; - - gig_dbg(DEBUG_INIT, "setting up inbuf"); - gigaset_inbuf_init(cs->inbuf, cs); - - cs->connected = 0; - cs->isdn_up = 0; - - gig_dbg(DEBUG_INIT, "setting up cmdbuf"); - cs->cmdbuf = cs->lastcmdbuf = NULL; - spin_lock_init(&cs->cmdlock); - cs->curlen = 0; - cs->cmdbytes = 0; - - gig_dbg(DEBUG_INIT, "setting up iif"); - if (gigaset_isdn_regdev(cs, modulename) < 0) { - pr_err("error registering ISDN device\n"); - goto error; - } - - make_valid(cs, VALID_ID); - ++cs->cs_init; - gig_dbg(DEBUG_INIT, "setting up hw"); - if (cs->ops->initcshw(cs) < 0) - goto error; - - ++cs->cs_init; - - /* set up character device */ - gigaset_if_init(cs); - - /* set up device sysfs */ - gigaset_init_dev_sysfs(cs); - - /* set up channel data structures */ - for (i = 0; i < channels; ++i) { - gig_dbg(DEBUG_INIT, "setting up bcs[%d]", i); - if (gigaset_initbcs(cs->bcs + i, cs, i) < 0) { - pr_err("could not allocate channel %d data\n", i); - goto error; - } - } - - spin_lock_irqsave(&cs->lock, flags); - cs->running = 1; - spin_unlock_irqrestore(&cs->lock, flags); - cs->timer.expires = jiffies + msecs_to_jiffies(GIG_TICK); - add_timer(&cs->timer); - - gig_dbg(DEBUG_INIT, "cs initialized"); - return cs; - -error: - gig_dbg(DEBUG_INIT, "failed"); - gigaset_freecs(cs); - return NULL; -} -EXPORT_SYMBOL_GPL(gigaset_initcs); - -/* ReInitialize the b-channel structure on hangup */ -void gigaset_bcs_reinit(struct bc_state *bcs) -{ - struct sk_buff *skb; - struct cardstate *cs = bcs->cs; - unsigned long flags; - - while ((skb = skb_dequeue(&bcs->squeue)) != NULL) - dev_kfree_skb(skb); - - spin_lock_irqsave(&cs->lock, flags); - clear_at_state(&bcs->at_state); - bcs->at_state.ConState = 0; - bcs->at_state.timer_active = 0; - bcs->at_state.timer_expires = 0; - bcs->at_state.cid = -1; /* No CID defined */ - spin_unlock_irqrestore(&cs->lock, flags); - - bcs->inputstate = 0; - -#ifdef CONFIG_GIGASET_DEBUG - bcs->emptycount = 0; -#endif - - bcs->rx_fcs = PPP_INITFCS; - bcs->chstate = 0; - - bcs->ignore = cs->ignoreframes; - dev_kfree_skb(bcs->rx_skb); - bcs->rx_skb = NULL; - - cs->ops->reinitbcshw(bcs); -} - -static void cleanup_cs(struct cardstate *cs) -{ - struct cmdbuf_t *cb, *tcb; - int i; - unsigned long flags; - - spin_lock_irqsave(&cs->lock, flags); - - cs->mode = M_UNKNOWN; - cs->mstate = MS_UNINITIALIZED; - - clear_at_state(&cs->at_state); - dealloc_temp_at_states(cs); - gigaset_at_init(&cs->at_state, NULL, cs, 0); - - cs->inbuf->inputstate = INS_command; - cs->inbuf->head = 0; - cs->inbuf->tail = 0; - - cb = cs->cmdbuf; - while (cb) { - tcb = cb; - cb = cb->next; - kfree(tcb); - } - cs->cmdbuf = cs->lastcmdbuf = NULL; - cs->curlen = 0; - cs->cmdbytes = 0; - cs->gotfwver = -1; - cs->dle = 0; - cs->cur_at_seq = 0; - cs->commands_pending = 0; - cs->cbytes = 0; - - spin_unlock_irqrestore(&cs->lock, flags); - - for (i = 0; i < cs->channels; ++i) { - gigaset_freebcs(cs->bcs + i); - if (gigaset_initbcs(cs->bcs + i, cs, i) < 0) - pr_err("could not allocate channel %d data\n", i); - } - - if (cs->waiting) { - cs->cmd_result = -ENODEV; - cs->waiting = 0; - wake_up_interruptible(&cs->waitqueue); - } -} - - -/** - * gigaset_start() - start device operations - * @cs: device descriptor structure. - * - * Prepares the device for use by setting up communication parameters, - * scheduling an EV_START event to initiate device initialization, and - * waiting for completion of the initialization. - * - * Return value: - * 0 on success, error code < 0 on failure - */ -int gigaset_start(struct cardstate *cs) -{ - unsigned long flags; - - if (mutex_lock_interruptible(&cs->mutex)) - return -EBUSY; - - spin_lock_irqsave(&cs->lock, flags); - cs->connected = 1; - spin_unlock_irqrestore(&cs->lock, flags); - - if (cs->mstate != MS_LOCKED) { - cs->ops->set_modem_ctrl(cs, 0, TIOCM_DTR | TIOCM_RTS); - cs->ops->baud_rate(cs, B115200); - cs->ops->set_line_ctrl(cs, CS8); - cs->control_state = TIOCM_DTR | TIOCM_RTS; - } - - cs->waiting = 1; - - if (!gigaset_add_event(cs, &cs->at_state, EV_START, NULL, 0, NULL)) { - cs->waiting = 0; - goto error; - } - gigaset_schedule_event(cs); - - wait_event(cs->waitqueue, !cs->waiting); - - mutex_unlock(&cs->mutex); - return 0; - -error: - mutex_unlock(&cs->mutex); - return -ENOMEM; -} -EXPORT_SYMBOL_GPL(gigaset_start); - -/** - * gigaset_shutdown() - shut down device operations - * @cs: device descriptor structure. - * - * Deactivates the device by scheduling an EV_SHUTDOWN event and - * waiting for completion of the shutdown. - * - * Return value: - * 0 - success, -ENODEV - error (no device associated) - */ -int gigaset_shutdown(struct cardstate *cs) -{ - mutex_lock(&cs->mutex); - - if (!(cs->flags & VALID_MINOR)) { - mutex_unlock(&cs->mutex); - return -ENODEV; - } - - cs->waiting = 1; - - if (!gigaset_add_event(cs, &cs->at_state, EV_SHUTDOWN, NULL, 0, NULL)) - goto exit; - gigaset_schedule_event(cs); - - wait_event(cs->waitqueue, !cs->waiting); - - cleanup_cs(cs); - -exit: - mutex_unlock(&cs->mutex); - return 0; -} -EXPORT_SYMBOL_GPL(gigaset_shutdown); - -/** - * gigaset_stop() - stop device operations - * @cs: device descriptor structure. - * - * Stops operations on the device by scheduling an EV_STOP event and - * waiting for completion of the shutdown. - */ -void gigaset_stop(struct cardstate *cs) -{ - mutex_lock(&cs->mutex); - - cs->waiting = 1; - - if (!gigaset_add_event(cs, &cs->at_state, EV_STOP, NULL, 0, NULL)) - goto exit; - gigaset_schedule_event(cs); - - wait_event(cs->waitqueue, !cs->waiting); - - cleanup_cs(cs); - -exit: - mutex_unlock(&cs->mutex); -} -EXPORT_SYMBOL_GPL(gigaset_stop); - -static LIST_HEAD(drivers); -static DEFINE_SPINLOCK(driver_lock); - -struct cardstate *gigaset_get_cs_by_id(int id) -{ - unsigned long flags; - struct cardstate *ret = NULL; - struct cardstate *cs; - struct gigaset_driver *drv; - unsigned i; - - spin_lock_irqsave(&driver_lock, flags); - list_for_each_entry(drv, &drivers, list) { - spin_lock(&drv->lock); - for (i = 0; i < drv->minors; ++i) { - cs = drv->cs + i; - if ((cs->flags & VALID_ID) && cs->myid == id) { - ret = cs; - break; - } - } - spin_unlock(&drv->lock); - if (ret) - break; - } - spin_unlock_irqrestore(&driver_lock, flags); - return ret; -} - -static struct cardstate *gigaset_get_cs_by_minor(unsigned minor) -{ - unsigned long flags; - struct cardstate *ret = NULL; - struct gigaset_driver *drv; - unsigned index; - - spin_lock_irqsave(&driver_lock, flags); - list_for_each_entry(drv, &drivers, list) { - if (minor < drv->minor || minor >= drv->minor + drv->minors) - continue; - index = minor - drv->minor; - spin_lock(&drv->lock); - if (drv->cs[index].flags & VALID_MINOR) - ret = drv->cs + index; - spin_unlock(&drv->lock); - if (ret) - break; - } - spin_unlock_irqrestore(&driver_lock, flags); - return ret; -} - -struct cardstate *gigaset_get_cs_by_tty(struct tty_struct *tty) -{ - return gigaset_get_cs_by_minor(tty->index + tty->driver->minor_start); -} - -/** - * gigaset_freedriver() - free all associated ressources of a driver - * @drv: driver descriptor structure. - * - * Unregisters the driver from the system and deallocates the driver - * structure @drv and all structures referenced from it. - * All devices should be shut down before calling this. - */ -void gigaset_freedriver(struct gigaset_driver *drv) -{ - unsigned long flags; - - spin_lock_irqsave(&driver_lock, flags); - list_del(&drv->list); - spin_unlock_irqrestore(&driver_lock, flags); - - gigaset_if_freedriver(drv); - - kfree(drv->cs); - kfree(drv); -} -EXPORT_SYMBOL_GPL(gigaset_freedriver); - -/** - * gigaset_initdriver() - initialize driver structure - * @minor: First minor number - * @minors: Number of minors this driver can handle - * @procname: Name of the driver - * @devname: Name of the device files (prefix without minor number) - * - * Allocate and initialize gigaset_driver structure. Initialize interface. - * - * Return value: - * Pointer to the gigaset_driver structure on success, NULL on failure. - */ -struct gigaset_driver *gigaset_initdriver(unsigned minor, unsigned minors, - const char *procname, - const char *devname, - const struct gigaset_ops *ops, - struct module *owner) -{ - struct gigaset_driver *drv; - unsigned long flags; - unsigned i; - - drv = kmalloc(sizeof *drv, GFP_KERNEL); - if (!drv) - return NULL; - - drv->have_tty = 0; - drv->minor = minor; - drv->minors = minors; - spin_lock_init(&drv->lock); - drv->blocked = 0; - drv->ops = ops; - drv->owner = owner; - INIT_LIST_HEAD(&drv->list); - - drv->cs = kmalloc_array(minors, sizeof(*drv->cs), GFP_KERNEL); - if (!drv->cs) - goto error; - - for (i = 0; i < minors; ++i) { - drv->cs[i].flags = 0; - drv->cs[i].driver = drv; - drv->cs[i].ops = drv->ops; - drv->cs[i].minor_index = i; - mutex_init(&drv->cs[i].mutex); - } - - gigaset_if_initdriver(drv, procname, devname); - - spin_lock_irqsave(&driver_lock, flags); - list_add(&drv->list, &drivers); - spin_unlock_irqrestore(&driver_lock, flags); - - return drv; - -error: - kfree(drv); - return NULL; -} -EXPORT_SYMBOL_GPL(gigaset_initdriver); - -/** - * gigaset_blockdriver() - block driver - * @drv: driver descriptor structure. - * - * Prevents the driver from attaching new devices, in preparation for - * deregistration. - */ -void gigaset_blockdriver(struct gigaset_driver *drv) -{ - drv->blocked = 1; -} -EXPORT_SYMBOL_GPL(gigaset_blockdriver); - -static int __init gigaset_init_module(void) -{ - /* in accordance with the principle of least astonishment, - * setting the 'debug' parameter to 1 activates a sensible - * set of default debug levels - */ - if (gigaset_debuglevel == 1) - gigaset_debuglevel = DEBUG_DEFAULT; - - pr_info(DRIVER_DESC DRIVER_DESC_DEBUG "\n"); - gigaset_isdn_regdrv(); - return 0; -} - -static void __exit gigaset_exit_module(void) -{ - gigaset_isdn_unregdrv(); -} - -module_init(gigaset_init_module); -module_exit(gigaset_exit_module); - -MODULE_AUTHOR(DRIVER_AUTHOR); -MODULE_DESCRIPTION(DRIVER_DESC); - -MODULE_LICENSE("GPL"); diff --git a/drivers/staging/isdn/gigaset/dummyll.c b/drivers/staging/isdn/gigaset/dummyll.c deleted file mode 100644 index 4b9637e5da6e..000000000000 --- a/drivers/staging/isdn/gigaset/dummyll.c +++ /dev/null @@ -1,74 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -/* - * Dummy LL interface for the Gigaset driver - * - * Copyright (c) 2009 by Tilman Schmidt <tilman@imap.cc>. - * - * ===================================================================== - * ===================================================================== - */ - -#include <linux/export.h> -#include "gigaset.h" - -void gigaset_skb_sent(struct bc_state *bcs, struct sk_buff *skb) -{ -} -EXPORT_SYMBOL_GPL(gigaset_skb_sent); - -void gigaset_skb_rcvd(struct bc_state *bcs, struct sk_buff *skb) -{ -} -EXPORT_SYMBOL_GPL(gigaset_skb_rcvd); - -void gigaset_isdn_rcv_err(struct bc_state *bcs) -{ -} -EXPORT_SYMBOL_GPL(gigaset_isdn_rcv_err); - -int gigaset_isdn_icall(struct at_state_t *at_state) -{ - return ICALL_IGNORE; -} - -void gigaset_isdn_connD(struct bc_state *bcs) -{ -} - -void gigaset_isdn_hupD(struct bc_state *bcs) -{ -} - -void gigaset_isdn_connB(struct bc_state *bcs) -{ -} - -void gigaset_isdn_hupB(struct bc_state *bcs) -{ -} - -void gigaset_isdn_start(struct cardstate *cs) -{ -} - -void gigaset_isdn_stop(struct cardstate *cs) -{ -} - -int gigaset_isdn_regdev(struct cardstate *cs, const char *isdnid) -{ - return 0; -} - -void gigaset_isdn_unregdev(struct cardstate *cs) -{ -} - -void gigaset_isdn_regdrv(void) -{ - pr_info("no ISDN subsystem interface\n"); -} - -void gigaset_isdn_unregdrv(void) -{ -} diff --git a/drivers/staging/isdn/gigaset/ev-layer.c b/drivers/staging/isdn/gigaset/ev-layer.c deleted file mode 100644 index f8bb1869c600..000000000000 --- a/drivers/staging/isdn/gigaset/ev-layer.c +++ /dev/null @@ -1,1910 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -/* - * Stuff used by all variants of the driver - * - * Copyright (c) 2001 by Stefan Eilers, - * Hansjoerg Lipp <hjlipp@web.de>, - * Tilman Schmidt <tilman@imap.cc>. - * - * ===================================================================== - * ===================================================================== - */ - -#include <linux/export.h> -#include "gigaset.h" - -/* ========================================================== */ -/* bit masks for pending commands */ -#define PC_DIAL 0x001 -#define PC_HUP 0x002 -#define PC_INIT 0x004 -#define PC_DLE0 0x008 -#define PC_DLE1 0x010 -#define PC_SHUTDOWN 0x020 -#define PC_ACCEPT 0x040 -#define PC_CID 0x080 -#define PC_NOCID 0x100 -#define PC_CIDMODE 0x200 -#define PC_UMMODE 0x400 - -/* types of modem responses */ -#define RT_NOTHING 0 -#define RT_ZSAU 1 -#define RT_RING 2 -#define RT_NUMBER 3 -#define RT_STRING 4 -#define RT_ZCAU 6 - -/* Possible ASCII responses */ -#define RSP_OK 0 -#define RSP_ERROR 1 -#define RSP_ZGCI 3 -#define RSP_RING 4 -#define RSP_ZVLS 5 -#define RSP_ZCAU 6 - -/* responses with values to store in at_state */ -/* - numeric */ -#define RSP_VAR 100 -#define RSP_ZSAU (RSP_VAR + VAR_ZSAU) -#define RSP_ZDLE (RSP_VAR + VAR_ZDLE) -#define RSP_ZCTP (RSP_VAR + VAR_ZCTP) -/* - string */ -#define RSP_STR (RSP_VAR + VAR_NUM) -#define RSP_NMBR (RSP_STR + STR_NMBR) -#define RSP_ZCPN (RSP_STR + STR_ZCPN) -#define RSP_ZCON (RSP_STR + STR_ZCON) -#define RSP_ZBC (RSP_STR + STR_ZBC) -#define RSP_ZHLC (RSP_STR + STR_ZHLC) - -#define RSP_WRONG_CID -2 /* unknown cid in cmd */ -#define RSP_INVAL -6 /* invalid response */ -#define RSP_NODEV -9 /* device not connected */ - -#define RSP_NONE -19 -#define RSP_STRING -20 -#define RSP_NULL -21 -#define RSP_INIT -27 -#define RSP_ANY -26 -#define RSP_LAST -28 - -/* actions for process_response */ -#define ACT_NOTHING 0 -#define ACT_SETDLE1 1 -#define ACT_SETDLE0 2 -#define ACT_FAILINIT 3 -#define ACT_HUPMODEM 4 -#define ACT_CONFIGMODE 5 -#define ACT_INIT 6 -#define ACT_DLE0 7 -#define ACT_DLE1 8 -#define ACT_FAILDLE0 9 -#define ACT_FAILDLE1 10 -#define ACT_RING 11 -#define ACT_CID 12 -#define ACT_FAILCID 13 -#define ACT_SDOWN 14 -#define ACT_FAILSDOWN 15 -#define ACT_DEBUG 16 -#define ACT_WARN 17 -#define ACT_DIALING 18 -#define ACT_ABORTDIAL 19 -#define ACT_DISCONNECT 20 -#define ACT_CONNECT 21 -#define ACT_REMOTEREJECT 22 -#define ACT_CONNTIMEOUT 23 -#define ACT_REMOTEHUP 24 -#define ACT_ABORTHUP 25 -#define ACT_ICALL 26 -#define ACT_ACCEPTED 27 -#define ACT_ABORTACCEPT 28 -#define ACT_TIMEOUT 29 -#define ACT_GETSTRING 30 -#define ACT_SETVER 31 -#define ACT_FAILVER 32 -#define ACT_GOTVER 33 -#define ACT_TEST 34 -#define ACT_ERROR 35 -#define ACT_ABORTCID 36 -#define ACT_ZCAU 37 -#define ACT_NOTIFY_BC_DOWN 38 -#define ACT_NOTIFY_BC_UP 39 -#define ACT_DIAL 40 -#define ACT_ACCEPT 41 -#define ACT_HUP 43 -#define ACT_IF_LOCK 44 -#define ACT_START 45 -#define ACT_STOP 46 -#define ACT_FAKEDLE0 47 -#define ACT_FAKEHUP 48 -#define ACT_FAKESDOWN 49 -#define ACT_SHUTDOWN 50 -#define ACT_PROC_CIDMODE 51 -#define ACT_UMODESET 52 -#define ACT_FAILUMODE 53 -#define ACT_CMODESET 54 -#define ACT_FAILCMODE 55 -#define ACT_IF_VER 56 -#define ACT_CMD 100 - -/* at command sequences */ -#define SEQ_NONE 0 -#define SEQ_INIT 100 -#define SEQ_DLE0 200 -#define SEQ_DLE1 250 -#define SEQ_CID 300 -#define SEQ_NOCID 350 -#define SEQ_HUP 400 -#define SEQ_DIAL 600 -#define SEQ_ACCEPT 720 -#define SEQ_SHUTDOWN 500 -#define SEQ_CIDMODE 10 -#define SEQ_UMMODE 11 - - -/* 100: init, 200: dle0, 250:dle1, 300: get cid (dial), 350: "hup" (no cid), - * 400: hup, 500: reset, 600: dial, 700: ring */ -struct reply_t gigaset_tab_nocid[] = -{ -/* resp_code, min_ConState, max_ConState, parameter, new_ConState, timeout, - * action, command */ - -/* initialize device, set cid mode if possible */ - {RSP_INIT, -1, -1, SEQ_INIT, 100, 1, {ACT_TIMEOUT} }, - - {EV_TIMEOUT, 100, 100, -1, 101, 3, {0}, "Z\r"}, - {RSP_OK, 101, 103, -1, 120, 5, {ACT_GETSTRING}, - "+GMR\r"}, - - {EV_TIMEOUT, 101, 101, -1, 102, 5, {0}, "Z\r"}, - {RSP_ERROR, 101, 101, -1, 102, 5, {0}, "Z\r"}, - - {EV_TIMEOUT, 102, 102, -1, 108, 5, {ACT_SETDLE1}, - "^SDLE=0\r"}, - {RSP_OK, 108, 108, -1, 104, -1}, - {RSP_ZDLE, 104, 104, 0, 103, 5, {0}, "Z\r"}, - {EV_TIMEOUT, 104, 104, -1, 0, 0, {ACT_FAILINIT} }, - {RSP_ERROR, 108, 108, -1, 0, 0, {ACT_FAILINIT} }, - - {EV_TIMEOUT, 108, 108, -1, 105, 2, {ACT_SETDLE0, - ACT_HUPMODEM, - ACT_TIMEOUT} }, - {EV_TIMEOUT, 105, 105, -1, 103, 5, {0}, "Z\r"}, - - {RSP_ERROR, 102, 102, -1, 107, 5, {0}, "^GETPRE\r"}, - {RSP_OK, 107, 107, -1, 0, 0, {ACT_CONFIGMODE} }, - {RSP_ERROR, 107, 107, -1, 0, 0, {ACT_FAILINIT} }, - {EV_TIMEOUT, 107, 107, -1, 0, 0, {ACT_FAILINIT} }, - - {RSP_ERROR, 103, 103, -1, 0, 0, {ACT_FAILINIT} }, - {EV_TIMEOUT, 103, 103, -1, 0, 0, {ACT_FAILINIT} }, - - {RSP_STRING, 120, 120, -1, 121, -1, {ACT_SETVER} }, - - {EV_TIMEOUT, 120, 121, -1, 0, 0, {ACT_FAILVER, - ACT_INIT} }, - {RSP_ERROR, 120, 121, -1, 0, 0, {ACT_FAILVER, - ACT_INIT} }, - {RSP_OK, 121, 121, -1, 0, 0, {ACT_GOTVER, - ACT_INIT} }, - {RSP_NONE, 121, 121, -1, 120, 0, {ACT_GETSTRING} }, - -/* leave dle mode */ - {RSP_INIT, 0, 0, SEQ_DLE0, 201, 5, {0}, "^SDLE=0\r"}, - {RSP_OK, 201, 201, -1, 202, -1}, - {RSP_ZDLE, 202, 202, 0, 0, 0, {ACT_DLE0} }, - {RSP_NODEV, 200, 249, -1, 0, 0, {ACT_FAKEDLE0} }, - {RSP_ERROR, 200, 249, -1, 0, 0, {ACT_FAILDLE0} }, - {EV_TIMEOUT, 200, 249, -1, 0, 0, {ACT_FAILDLE0} }, - -/* enter dle mode */ - {RSP_INIT, 0, 0, SEQ_DLE1, 251, 5, {0}, "^SDLE=1\r"}, - {RSP_OK, 251, 251, -1, 252, -1}, - {RSP_ZDLE, 252, 252, 1, 0, 0, {ACT_DLE1} }, - {RSP_ERROR, 250, 299, -1, 0, 0, {ACT_FAILDLE1} }, - {EV_TIMEOUT, 250, 299, -1, 0, 0, {ACT_FAILDLE1} }, - -/* incoming call */ - {RSP_RING, -1, -1, -1, -1, -1, {ACT_RING} }, - -/* get cid */ - {RSP_INIT, 0, 0, SEQ_CID, 301, 5, {0}, "^SGCI?\r"}, - {RSP_OK, 301, 301, -1, 302, -1}, - {RSP_ZGCI, 302, 302, -1, 0, 0, {ACT_CID} }, - {RSP_ERROR, 301, 349, -1, 0, 0, {ACT_FAILCID} }, - {EV_TIMEOUT, 301, 349, -1, 0, 0, {ACT_FAILCID} }, - -/* enter cid mode */ - {RSP_INIT, 0, 0, SEQ_CIDMODE, 150, 5, {0}, "^SGCI=1\r"}, - {RSP_OK, 150, 150, -1, 0, 0, {ACT_CMODESET} }, - {RSP_ERROR, 150, 150, -1, 0, 0, {ACT_FAILCMODE} }, - {EV_TIMEOUT, 150, 150, -1, 0, 0, {ACT_FAILCMODE} }, - -/* leave cid mode */ - {RSP_INIT, 0, 0, SEQ_UMMODE, 160, 5, {0}, "Z\r"}, - {RSP_OK, 160, 160, -1, 0, 0, {ACT_UMODESET} }, - {RSP_ERROR, 160, 160, -1, 0, 0, {ACT_FAILUMODE} }, - {EV_TIMEOUT, 160, 160, -1, 0, 0, {ACT_FAILUMODE} }, - -/* abort getting cid */ - {RSP_INIT, 0, 0, SEQ_NOCID, 0, 0, {ACT_ABORTCID} }, - -/* reset */ - {RSP_INIT, 0, 0, SEQ_SHUTDOWN, 504, 5, {0}, "Z\r"}, - {RSP_OK, 504, 504, -1, 0, 0, {ACT_SDOWN} }, - {RSP_ERROR, 501, 599, -1, 0, 0, {ACT_FAILSDOWN} }, - {EV_TIMEOUT, 501, 599, -1, 0, 0, {ACT_FAILSDOWN} }, - {RSP_NODEV, 501, 599, -1, 0, 0, {ACT_FAKESDOWN} }, - - {EV_PROC_CIDMODE, -1, -1, -1, -1, -1, {ACT_PROC_CIDMODE} }, - {EV_IF_LOCK, -1, -1, -1, -1, -1, {ACT_IF_LOCK} }, - {EV_IF_VER, -1, -1, -1, -1, -1, {ACT_IF_VER} }, - {EV_START, -1, -1, -1, -1, -1, {ACT_START} }, - {EV_STOP, -1, -1, -1, -1, -1, {ACT_STOP} }, - {EV_SHUTDOWN, -1, -1, -1, -1, -1, {ACT_SHUTDOWN} }, - -/* misc. */ - {RSP_ERROR, -1, -1, -1, -1, -1, {ACT_ERROR} }, - {RSP_ZCAU, -1, -1, -1, -1, -1, {ACT_ZCAU} }, - {RSP_NONE, -1, -1, -1, -1, -1, {ACT_DEBUG} }, - {RSP_ANY, -1, -1, -1, -1, -1, {ACT_WARN} }, - {RSP_LAST} -}; - -/* 600: start dialing, 650: dial in progress, 800: connection is up, 700: ring, - * 400: hup, 750: accepted icall */ -struct reply_t gigaset_tab_cid[] = -{ -/* resp_code, min_ConState, max_ConState, parameter, new_ConState, timeout, - * action, command */ - -/* dial */ - {EV_DIAL, -1, -1, -1, -1, -1, {ACT_DIAL} }, - {RSP_INIT, 0, 0, SEQ_DIAL, 601, 5, {ACT_CMD + AT_BC} }, - {RSP_OK, 601, 601, -1, 603, 5, {ACT_CMD + AT_PROTO} }, - {RSP_OK, 603, 603, -1, 604, 5, {ACT_CMD + AT_TYPE} }, - {RSP_OK, 604, 604, -1, 605, 5, {ACT_CMD + AT_MSN} }, - {RSP_NULL, 605, 605, -1, 606, 5, {ACT_CMD + AT_CLIP} }, - {RSP_OK, 605, 605, -1, 606, 5, {ACT_CMD + AT_CLIP} }, - {RSP_NULL, 606, 606, -1, 607, 5, {ACT_CMD + AT_ISO} }, - {RSP_OK, 606, 606, -1, 607, 5, {ACT_CMD + AT_ISO} }, - {RSP_OK, 607, 607, -1, 608, 5, {0}, "+VLS=17\r"}, - {RSP_OK, 608, 608, -1, 609, -1}, - {RSP_ZSAU, 609, 609, ZSAU_PROCEEDING, 610, 5, {ACT_CMD + AT_DIAL} }, - {RSP_OK, 610, 610, -1, 650, 0, {ACT_DIALING} }, - - {RSP_ERROR, 601, 610, -1, 0, 0, {ACT_ABORTDIAL} }, - {EV_TIMEOUT, 601, 610, -1, 0, 0, {ACT_ABORTDIAL} }, - -/* optional dialing responses */ - {EV_BC_OPEN, 650, 650, -1, 651, -1}, - {RSP_ZVLS, 609, 651, 17, -1, -1, {ACT_DEBUG} }, - {RSP_ZCTP, 610, 651, -1, -1, -1, {ACT_DEBUG} }, - {RSP_ZCPN, 610, 651, -1, -1, -1, {ACT_DEBUG} }, - {RSP_ZSAU, 650, 651, ZSAU_CALL_DELIVERED, -1, -1, {ACT_DEBUG} }, - -/* connect */ - {RSP_ZSAU, 650, 650, ZSAU_ACTIVE, 800, -1, {ACT_CONNECT} }, - {RSP_ZSAU, 651, 651, ZSAU_ACTIVE, 800, -1, {ACT_CONNECT, - ACT_NOTIFY_BC_UP} }, - {RSP_ZSAU, 750, 750, ZSAU_ACTIVE, 800, -1, {ACT_CONNECT} }, - {RSP_ZSAU, 751, 751, ZSAU_ACTIVE, 800, -1, {ACT_CONNECT, - ACT_NOTIFY_BC_UP} }, - {EV_BC_OPEN, 800, 800, -1, 800, -1, {ACT_NOTIFY_BC_UP} }, - -/* remote hangup */ - {RSP_ZSAU, 650, 651, ZSAU_DISCONNECT_IND, 0, 0, {ACT_REMOTEREJECT} }, - {RSP_ZSAU, 750, 751, ZSAU_DISCONNECT_IND, 0, 0, {ACT_REMOTEHUP} }, - {RSP_ZSAU, 800, 800, ZSAU_DISCONNECT_IND, 0, 0, {ACT_REMOTEHUP} }, - -/* hangup */ - {EV_HUP, -1, -1, -1, -1, -1, {ACT_HUP} }, - {RSP_INIT, -1, -1, SEQ_HUP, 401, 5, {0}, "+VLS=0\r"}, - {RSP_OK, 401, 401, -1, 402, 5}, - {RSP_ZVLS, 402, 402, 0, 403, 5}, - {RSP_ZSAU, 403, 403, ZSAU_DISCONNECT_REQ, -1, -1, {ACT_DEBUG} }, - {RSP_ZSAU, 403, 403, ZSAU_NULL, 0, 0, {ACT_DISCONNECT} }, - {RSP_NODEV, 401, 403, -1, 0, 0, {ACT_FAKEHUP} }, - {RSP_ERROR, 401, 401, -1, 0, 0, {ACT_ABORTHUP} }, - {EV_TIMEOUT, 401, 403, -1, 0, 0, {ACT_ABORTHUP} }, - - {EV_BC_CLOSED, 0, 0, -1, 0, -1, {ACT_NOTIFY_BC_DOWN} }, - -/* ring */ - {RSP_ZBC, 700, 700, -1, -1, -1, {0} }, - {RSP_ZHLC, 700, 700, -1, -1, -1, {0} }, - {RSP_NMBR, 700, 700, -1, -1, -1, {0} }, - {RSP_ZCPN, 700, 700, -1, -1, -1, {0} }, - {RSP_ZCTP, 700, 700, -1, -1, -1, {0} }, - {EV_TIMEOUT, 700, 700, -1, 720, 720, {ACT_ICALL} }, - {EV_BC_CLOSED, 720, 720, -1, 0, -1, {ACT_NOTIFY_BC_DOWN} }, - -/*accept icall*/ - {EV_ACCEPT, -1, -1, -1, -1, -1, {ACT_ACCEPT} }, - {RSP_INIT, 720, 720, SEQ_ACCEPT, 721, 5, {ACT_CMD + AT_PROTO} }, - {RSP_OK, 721, 721, -1, 722, 5, {ACT_CMD + AT_ISO} }, - {RSP_OK, 722, 722, -1, 723, 5, {0}, "+VLS=17\r"}, - {RSP_OK, 723, 723, -1, 724, 5, {0} }, - {RSP_ZVLS, 724, 724, 17, 750, 50, {ACT_ACCEPTED} }, - {RSP_ERROR, 721, 729, -1, 0, 0, {ACT_ABORTACCEPT} }, - {EV_TIMEOUT, 721, 729, -1, 0, 0, {ACT_ABORTACCEPT} }, - {RSP_ZSAU, 700, 729, ZSAU_NULL, 0, 0, {ACT_ABORTACCEPT} }, - {RSP_ZSAU, 700, 729, ZSAU_ACTIVE, 0, 0, {ACT_ABORTACCEPT} }, - {RSP_ZSAU, 700, 729, ZSAU_DISCONNECT_IND, 0, 0, {ACT_ABORTACCEPT} }, - - {EV_BC_OPEN, 750, 750, -1, 751, -1}, - {EV_TIMEOUT, 750, 751, -1, 0, 0, {ACT_CONNTIMEOUT} }, - -/* B channel closed (general case) */ - {EV_BC_CLOSED, -1, -1, -1, -1, -1, {ACT_NOTIFY_BC_DOWN} }, - -/* misc. */ - {RSP_ZCON, -1, -1, -1, -1, -1, {ACT_DEBUG} }, - {RSP_ZCAU, -1, -1, -1, -1, -1, {ACT_ZCAU} }, - {RSP_NONE, -1, -1, -1, -1, -1, {ACT_DEBUG} }, - {RSP_ANY, -1, -1, -1, -1, -1, {ACT_WARN} }, - {RSP_LAST} -}; - - -static const struct resp_type_t { - char *response; - int resp_code; - int type; -} -resp_type[] = -{ - {"OK", RSP_OK, RT_NOTHING}, - {"ERROR", RSP_ERROR, RT_NOTHING}, - {"ZSAU", RSP_ZSAU, RT_ZSAU}, - {"ZCAU", RSP_ZCAU, RT_ZCAU}, - {"RING", RSP_RING, RT_RING}, - {"ZGCI", RSP_ZGCI, RT_NUMBER}, - {"ZVLS", RSP_ZVLS, RT_NUMBER}, - {"ZCTP", RSP_ZCTP, RT_NUMBER}, - {"ZDLE", RSP_ZDLE, RT_NUMBER}, - {"ZHLC", RSP_ZHLC, RT_STRING}, - {"ZBC", RSP_ZBC, RT_STRING}, - {"NMBR", RSP_NMBR, RT_STRING}, - {"ZCPN", RSP_ZCPN, RT_STRING}, - {"ZCON", RSP_ZCON, RT_STRING}, - {NULL, 0, 0} -}; - -static const struct zsau_resp_t { - char *str; - int code; -} -zsau_resp[] = -{ - {"OUTGOING_CALL_PROCEEDING", ZSAU_PROCEEDING}, - {"CALL_DELIVERED", ZSAU_CALL_DELIVERED}, - {"ACTIVE", ZSAU_ACTIVE}, - {"DISCONNECT_IND", ZSAU_DISCONNECT_IND}, - {"NULL", ZSAU_NULL}, - {"DISCONNECT_REQ", ZSAU_DISCONNECT_REQ}, - {NULL, ZSAU_UNKNOWN} -}; - -/* check for and remove fixed string prefix - * If s starts with prefix terminated by a non-alphanumeric character, - * return pointer to the first character after that, otherwise return NULL. - */ -static char *skip_prefix(char *s, const char *prefix) -{ - while (*prefix) - if (*s++ != *prefix++) - return NULL; - if (isalnum(*s)) - return NULL; - return s; -} - -/* queue event with CID */ -static void add_cid_event(struct cardstate *cs, int cid, int type, - void *ptr, int parameter) -{ - unsigned long flags; - unsigned next, tail; - struct event_t *event; - - gig_dbg(DEBUG_EVENT, "queueing event %d for cid %d", type, cid); - - spin_lock_irqsave(&cs->ev_lock, flags); - - tail = cs->ev_tail; - next = (tail + 1) % MAX_EVENTS; - if (unlikely(next == cs->ev_head)) { - dev_err(cs->dev, "event queue full\n"); - kfree(ptr); - } else { - event = cs->events + tail; - event->type = type; - event->cid = cid; - event->ptr = ptr; - event->arg = NULL; - event->parameter = parameter; - event->at_state = NULL; - cs->ev_tail = next; - } - - spin_unlock_irqrestore(&cs->ev_lock, flags); -} - -/** - * gigaset_handle_modem_response() - process received modem response - * @cs: device descriptor structure. - * - * Called by asyncdata/isocdata if a block of data received from the - * device must be processed as a modem command response. The data is - * already in the cs structure. - */ -void gigaset_handle_modem_response(struct cardstate *cs) -{ - char *eoc, *psep, *ptr; - const struct resp_type_t *rt; - const struct zsau_resp_t *zr; - int cid, parameter; - u8 type, value; - - if (!cs->cbytes) { - /* ignore additional LFs/CRs (M10x config mode or cx100) */ - gig_dbg(DEBUG_MCMD, "skipped EOL [%02X]", cs->respdata[0]); - return; - } - cs->respdata[cs->cbytes] = 0; - - if (cs->at_state.getstring) { - /* state machine wants next line verbatim */ - cs->at_state.getstring = 0; - ptr = kstrdup(cs->respdata, GFP_ATOMIC); - gig_dbg(DEBUG_EVENT, "string==%s", ptr ? ptr : "NULL"); - add_cid_event(cs, 0, RSP_STRING, ptr, 0); - return; - } - - /* look up response type */ - for (rt = resp_type; rt->response; ++rt) { - eoc = skip_prefix(cs->respdata, rt->response); - if (eoc) - break; - } - if (!rt->response) { - add_cid_event(cs, 0, RSP_NONE, NULL, 0); - gig_dbg(DEBUG_EVENT, "unknown modem response: '%s'\n", - cs->respdata); - return; - } - - /* check for CID */ - psep = strrchr(cs->respdata, ';'); - if (psep && - !kstrtoint(psep + 1, 10, &cid) && - cid >= 1 && cid <= 65535) { - /* valid CID: chop it off */ - *psep = 0; - } else { - /* no valid CID: leave unchanged */ - cid = 0; - } - - gig_dbg(DEBUG_EVENT, "CMD received: %s", cs->respdata); - if (cid) - gig_dbg(DEBUG_EVENT, "CID: %d", cid); - - switch (rt->type) { - case RT_NOTHING: - /* check parameter separator */ - if (*eoc) - goto bad_param; /* extra parameter */ - - add_cid_event(cs, cid, rt->resp_code, NULL, 0); - break; - - case RT_RING: - /* check parameter separator */ - if (!*eoc) - eoc = NULL; /* no parameter */ - else if (*eoc++ != ',') - goto bad_param; - - add_cid_event(cs, 0, rt->resp_code, NULL, cid); - - /* process parameters as individual responses */ - while (eoc) { - /* look up parameter type */ - psep = NULL; - for (rt = resp_type; rt->response; ++rt) { - psep = skip_prefix(eoc, rt->response); - if (psep) - break; - } - - /* all legal parameters are of type RT_STRING */ - if (!psep || rt->type != RT_STRING) { - dev_warn(cs->dev, - "illegal RING parameter: '%s'\n", - eoc); - return; - } - - /* skip parameter value separator */ - if (*psep++ != '=') - goto bad_param; - - /* look up end of parameter */ - eoc = strchr(psep, ','); - if (eoc) - *eoc++ = 0; - - /* retrieve parameter value */ - ptr = kstrdup(psep, GFP_ATOMIC); - - /* queue event */ - add_cid_event(cs, cid, rt->resp_code, ptr, 0); - } - break; - - case RT_ZSAU: - /* check parameter separator */ - if (!*eoc) { - /* no parameter */ - add_cid_event(cs, cid, rt->resp_code, NULL, ZSAU_NONE); - break; - } - if (*eoc++ != '=') - goto bad_param; - - /* look up parameter value */ - for (zr = zsau_resp; zr->str; ++zr) - if (!strcmp(eoc, zr->str)) - break; - if (!zr->str) - goto bad_param; - - add_cid_event(cs, cid, rt->resp_code, NULL, zr->code); - break; - - case RT_STRING: - /* check parameter separator */ - if (*eoc++ != '=') - goto bad_param; - - /* retrieve parameter value */ - ptr = kstrdup(eoc, GFP_ATOMIC); - - /* queue event */ - add_cid_event(cs, cid, rt->resp_code, ptr, 0); - break; - - case RT_ZCAU: - /* check parameter separators */ - if (*eoc++ != '=') - goto bad_param; - psep = strchr(eoc, ','); - if (!psep) - goto bad_param; - *psep++ = 0; - - /* decode parameter values */ - if (kstrtou8(eoc, 16, &type) || kstrtou8(psep, 16, &value)) { - *--psep = ','; - goto bad_param; - } - parameter = (type << 8) | value; - - add_cid_event(cs, cid, rt->resp_code, NULL, parameter); - break; - - case RT_NUMBER: - /* check parameter separator */ - if (*eoc++ != '=') - goto bad_param; - - /* decode parameter value */ - if (kstrtoint(eoc, 10, ¶meter)) - goto bad_param; - - /* special case ZDLE: set flag before queueing event */ - if (rt->resp_code == RSP_ZDLE) - cs->dle = parameter; - - add_cid_event(cs, cid, rt->resp_code, NULL, parameter); - break; - -bad_param: - /* parameter unexpected, incomplete or malformed */ - dev_warn(cs->dev, "bad parameter in response '%s'\n", - cs->respdata); - add_cid_event(cs, cid, rt->resp_code, NULL, -1); - break; - - default: - dev_err(cs->dev, "%s: internal error on '%s'\n", - __func__, cs->respdata); - } -} -EXPORT_SYMBOL_GPL(gigaset_handle_modem_response); - -/* disconnect_nobc - * process closing of connection associated with given AT state structure - * without B channel - */ -static void disconnect_nobc(struct at_state_t **at_state_p, - struct cardstate *cs) -{ - unsigned long flags; - - spin_lock_irqsave(&cs->lock, flags); - ++(*at_state_p)->seq_index; - - /* revert to selected idle mode */ - if (!cs->cidmode) { - cs->at_state.pending_commands |= PC_UMMODE; - gig_dbg(DEBUG_EVENT, "Scheduling PC_UMMODE"); - cs->commands_pending = 1; - } - - /* check for and deallocate temporary AT state */ - if (!list_empty(&(*at_state_p)->list)) { - list_del(&(*at_state_p)->list); - kfree(*at_state_p); - *at_state_p = NULL; - } - - spin_unlock_irqrestore(&cs->lock, flags); -} - -/* disconnect_bc - * process closing of connection associated with given AT state structure - * and B channel - */ -static void disconnect_bc(struct at_state_t *at_state, - struct cardstate *cs, struct bc_state *bcs) -{ - unsigned long flags; - - spin_lock_irqsave(&cs->lock, flags); - ++at_state->seq_index; - - /* revert to selected idle mode */ - if (!cs->cidmode) { - cs->at_state.pending_commands |= PC_UMMODE; - gig_dbg(DEBUG_EVENT, "Scheduling PC_UMMODE"); - cs->commands_pending = 1; - } - spin_unlock_irqrestore(&cs->lock, flags); - - /* invoke hardware specific handler */ - cs->ops->close_bchannel(bcs); - - /* notify LL */ - if (bcs->chstate & (CHS_D_UP | CHS_NOTIFY_LL)) { - bcs->chstate &= ~(CHS_D_UP | CHS_NOTIFY_LL); - gigaset_isdn_hupD(bcs); - } -} - -/* get_free_channel - * get a free AT state structure: either one of those associated with the - * B channels of the Gigaset device, or if none of those is available, - * a newly allocated one with bcs=NULL - * The structure should be freed by calling disconnect_nobc() after use. - */ -static inline struct at_state_t *get_free_channel(struct cardstate *cs, - int cid) -/* cids: >0: siemens-cid - * 0: without cid - * -1: no cid assigned yet - */ -{ - unsigned long flags; - int i; - struct at_state_t *ret; - - for (i = 0; i < cs->channels; ++i) - if (gigaset_get_channel(cs->bcs + i) >= 0) { - ret = &cs->bcs[i].at_state; - ret->cid = cid; - return ret; - } - - spin_lock_irqsave(&cs->lock, flags); - ret = kmalloc(sizeof(struct at_state_t), GFP_ATOMIC); - if (ret) { - gigaset_at_init(ret, NULL, cs, cid); - list_add(&ret->list, &cs->temp_at_states); - } - spin_unlock_irqrestore(&cs->lock, flags); - return ret; -} - -static void init_failed(struct cardstate *cs, int mode) -{ - int i; - struct at_state_t *at_state; - - cs->at_state.pending_commands &= ~PC_INIT; - cs->mode = mode; - cs->mstate = MS_UNINITIALIZED; - gigaset_free_channels(cs); - for (i = 0; i < cs->channels; ++i) { - at_state = &cs->bcs[i].at_state; - if (at_state->pending_commands & PC_CID) { - at_state->pending_commands &= ~PC_CID; - at_state->pending_commands |= PC_NOCID; - cs->commands_pending = 1; - } - } -} - -static void schedule_init(struct cardstate *cs, int state) -{ - if (cs->at_state.pending_commands & PC_INIT) { - gig_dbg(DEBUG_EVENT, "not scheduling PC_INIT again"); - return; - } - cs->mstate = state; - cs->mode = M_UNKNOWN; - gigaset_block_channels(cs); - cs->at_state.pending_commands |= PC_INIT; - gig_dbg(DEBUG_EVENT, "Scheduling PC_INIT"); - cs->commands_pending = 1; -} - -/* send an AT command - * adding the "AT" prefix, cid and DLE encapsulation as appropriate - */ -static void send_command(struct cardstate *cs, const char *cmd, - struct at_state_t *at_state) -{ - int cid = at_state->cid; - struct cmdbuf_t *cb; - size_t buflen; - - buflen = strlen(cmd) + 12; /* DLE ( A T 1 2 3 4 5 <cmd> DLE ) \0 */ - cb = kmalloc(sizeof(struct cmdbuf_t) + buflen, GFP_ATOMIC); - if (!cb) { - dev_err(cs->dev, "%s: out of memory\n", __func__); - return; - } - if (cid > 0 && cid <= 65535) - cb->len = snprintf(cb->buf, buflen, - cs->dle ? "\020(AT%d%s\020)" : "AT%d%s", - cid, cmd); - else - cb->len = snprintf(cb->buf, buflen, - cs->dle ? "\020(AT%s\020)" : "AT%s", - cmd); - cb->offset = 0; - cb->next = NULL; - cb->wake_tasklet = NULL; - cs->ops->write_cmd(cs, cb); -} - -static struct at_state_t *at_state_from_cid(struct cardstate *cs, int cid) -{ - struct at_state_t *at_state; - int i; - unsigned long flags; - - if (cid == 0) - return &cs->at_state; - - for (i = 0; i < cs->channels; ++i) - if (cid == cs->bcs[i].at_state.cid) - return &cs->bcs[i].at_state; - - spin_lock_irqsave(&cs->lock, flags); - - list_for_each_entry(at_state, &cs->temp_at_states, list) - if (cid == at_state->cid) { - spin_unlock_irqrestore(&cs->lock, flags); - return at_state; - } - - spin_unlock_irqrestore(&cs->lock, flags); - - return NULL; -} - -static void bchannel_down(struct bc_state *bcs) -{ - if (bcs->chstate & CHS_B_UP) { - bcs->chstate &= ~CHS_B_UP; - gigaset_isdn_hupB(bcs); - } - - if (bcs->chstate & (CHS_D_UP | CHS_NOTIFY_LL)) { - bcs->chstate &= ~(CHS_D_UP | CHS_NOTIFY_LL); - gigaset_isdn_hupD(bcs); - } - - gigaset_free_channel(bcs); - - gigaset_bcs_reinit(bcs); -} - -static void bchannel_up(struct bc_state *bcs) -{ - if (bcs->chstate & CHS_B_UP) { - dev_notice(bcs->cs->dev, "%s: B channel already up\n", - __func__); - return; - } - - bcs->chstate |= CHS_B_UP; - gigaset_isdn_connB(bcs); -} - -static void start_dial(struct at_state_t *at_state, void *data, - unsigned seq_index) -{ - struct bc_state *bcs = at_state->bcs; - struct cardstate *cs = at_state->cs; - char **commands = data; - unsigned long flags; - int i; - - bcs->chstate |= CHS_NOTIFY_LL; - - spin_lock_irqsave(&cs->lock, flags); - if (at_state->seq_index != seq_index) { - spin_unlock_irqrestore(&cs->lock, flags); - goto error; - } - spin_unlock_irqrestore(&cs->lock, flags); - - for (i = 0; i < AT_NUM; ++i) { - kfree(bcs->commands[i]); - bcs->commands[i] = commands[i]; - } - - at_state->pending_commands |= PC_CID; - gig_dbg(DEBUG_EVENT, "Scheduling PC_CID"); - cs->commands_pending = 1; - return; - -error: - for (i = 0; i < AT_NUM; ++i) { - kfree(commands[i]); - commands[i] = NULL; - } - at_state->pending_commands |= PC_NOCID; - gig_dbg(DEBUG_EVENT, "Scheduling PC_NOCID"); - cs->commands_pending = 1; - return; -} - -static void start_accept(struct at_state_t *at_state) -{ - struct cardstate *cs = at_state->cs; - struct bc_state *bcs = at_state->bcs; - int i; - - for (i = 0; i < AT_NUM; ++i) { - kfree(bcs->commands[i]); - bcs->commands[i] = NULL; - } - - bcs->commands[AT_PROTO] = kmalloc(9, GFP_ATOMIC); - bcs->commands[AT_ISO] = kmalloc(9, GFP_ATOMIC); - if (!bcs->commands[AT_PROTO] || !bcs->commands[AT_ISO]) { - dev_err(at_state->cs->dev, "out of memory\n"); - /* error reset */ - at_state->pending_commands |= PC_HUP; - gig_dbg(DEBUG_EVENT, "Scheduling PC_HUP"); - cs->commands_pending = 1; - return; - } - - snprintf(bcs->commands[AT_PROTO], 9, "^SBPR=%u\r", bcs->proto2); - snprintf(bcs->commands[AT_ISO], 9, "^SISO=%u\r", bcs->channel + 1); - - at_state->pending_commands |= PC_ACCEPT; - gig_dbg(DEBUG_EVENT, "Scheduling PC_ACCEPT"); - cs->commands_pending = 1; -} - -static void do_start(struct cardstate *cs) -{ - gigaset_free_channels(cs); - - if (cs->mstate != MS_LOCKED) - schedule_init(cs, MS_INIT); - - cs->isdn_up = 1; - gigaset_isdn_start(cs); - - cs->waiting = 0; - wake_up(&cs->waitqueue); -} - -static void finish_shutdown(struct cardstate *cs) -{ - if (cs->mstate != MS_LOCKED) { - cs->mstate = MS_UNINITIALIZED; - cs->mode = M_UNKNOWN; - } - - /* Tell the LL that the device is not available .. */ - if (cs->isdn_up) { - cs->isdn_up = 0; - gigaset_isdn_stop(cs); - } - - /* The rest is done by cleanup_cs() in process context. */ - - cs->cmd_result = -ENODEV; - cs->waiting = 0; - wake_up(&cs->waitqueue); -} - -static void do_shutdown(struct cardstate *cs) -{ - gigaset_block_channels(cs); - - if (cs->mstate == MS_READY) { - cs->mstate = MS_SHUTDOWN; - cs->at_state.pending_commands |= PC_SHUTDOWN; - gig_dbg(DEBUG_EVENT, "Scheduling PC_SHUTDOWN"); - cs->commands_pending = 1; - } else - finish_shutdown(cs); -} - -static void do_stop(struct cardstate *cs) -{ - unsigned long flags; - - spin_lock_irqsave(&cs->lock, flags); - cs->connected = 0; - spin_unlock_irqrestore(&cs->lock, flags); - - do_shutdown(cs); -} - -/* Entering cid mode or getting a cid failed: - * try to initialize the device and try again. - * - * channel >= 0: getting cid for the channel failed - * channel < 0: entering cid mode failed - * - * returns 0 on success, <0 on failure - */ -static int reinit_and_retry(struct cardstate *cs, int channel) -{ - int i; - - if (--cs->retry_count <= 0) - return -EFAULT; - - for (i = 0; i < cs->channels; ++i) - if (cs->bcs[i].at_state.cid > 0) - return -EBUSY; - - if (channel < 0) - dev_warn(cs->dev, - "Could not enter cid mode. Reinit device and try again.\n"); - else { - dev_warn(cs->dev, - "Could not get a call id. Reinit device and try again.\n"); - cs->bcs[channel].at_state.pending_commands |= PC_CID; - } - schedule_init(cs, MS_INIT); - return 0; -} - -static int at_state_invalid(struct cardstate *cs, - struct at_state_t *test_ptr) -{ - unsigned long flags; - unsigned channel; - struct at_state_t *at_state; - int retval = 0; - - spin_lock_irqsave(&cs->lock, flags); - - if (test_ptr == &cs->at_state) - goto exit; - - list_for_each_entry(at_state, &cs->temp_at_states, list) - if (at_state == test_ptr) - goto exit; - - for (channel = 0; channel < cs->channels; ++channel) - if (&cs->bcs[channel].at_state == test_ptr) - goto exit; - - retval = 1; -exit: - spin_unlock_irqrestore(&cs->lock, flags); - return retval; -} - -static void handle_icall(struct cardstate *cs, struct bc_state *bcs, - struct at_state_t *at_state) -{ - int retval; - - retval = gigaset_isdn_icall(at_state); - switch (retval) { - case ICALL_ACCEPT: - break; - default: - dev_err(cs->dev, "internal error: disposition=%d\n", retval); - /* fall through */ - case ICALL_IGNORE: - case ICALL_REJECT: - /* hang up actively - * Device doc says that would reject the call. - * In fact it doesn't. - */ - at_state->pending_commands |= PC_HUP; - cs->commands_pending = 1; - break; - } -} - -static int do_lock(struct cardstate *cs) -{ - int mode; - int i; - - switch (cs->mstate) { - case MS_UNINITIALIZED: - case MS_READY: - if (cs->cur_at_seq || !list_empty(&cs->temp_at_states) || - cs->at_state.pending_commands) - return -EBUSY; - - for (i = 0; i < cs->channels; ++i) - if (cs->bcs[i].at_state.pending_commands) - return -EBUSY; - - if (gigaset_get_channels(cs) < 0) - return -EBUSY; - - break; - case MS_LOCKED: - break; - default: - return -EBUSY; - } - - mode = cs->mode; - cs->mstate = MS_LOCKED; - cs->mode = M_UNKNOWN; - - return mode; -} - -static int do_unlock(struct cardstate *cs) -{ - if (cs->mstate != MS_LOCKED) - return -EINVAL; - - cs->mstate = MS_UNINITIALIZED; - cs->mode = M_UNKNOWN; - gigaset_free_channels(cs); - if (cs->connected) - schedule_init(cs, MS_INIT); - - return 0; -} - -static void do_action(int action, struct cardstate *cs, - struct bc_state *bcs, - struct at_state_t **p_at_state, char **pp_command, - int *p_genresp, int *p_resp_code, - struct event_t *ev) -{ - struct at_state_t *at_state = *p_at_state; - struct bc_state *bcs2; - unsigned long flags; - - int channel; - - unsigned char *s, *e; - int i; - unsigned long val; - - switch (action) { - case ACT_NOTHING: - break; - case ACT_TIMEOUT: - at_state->waiting = 1; - break; - case ACT_INIT: - cs->at_state.pending_commands &= ~PC_INIT; - cs->cur_at_seq = SEQ_NONE; - cs->mode = M_UNIMODEM; - spin_lock_irqsave(&cs->lock, flags); - if (!cs->cidmode) { - spin_unlock_irqrestore(&cs->lock, flags); - gigaset_free_channels(cs); - cs->mstate = MS_READY; - break; - } - spin_unlock_irqrestore(&cs->lock, flags); - cs->at_state.pending_commands |= PC_CIDMODE; - gig_dbg(DEBUG_EVENT, "Scheduling PC_CIDMODE"); - cs->commands_pending = 1; - break; - case ACT_FAILINIT: - dev_warn(cs->dev, "Could not initialize the device.\n"); - cs->dle = 0; - init_failed(cs, M_UNKNOWN); - cs->cur_at_seq = SEQ_NONE; - break; - case ACT_CONFIGMODE: - init_failed(cs, M_CONFIG); - cs->cur_at_seq = SEQ_NONE; - break; - case ACT_SETDLE1: - cs->dle = 1; - /* cs->inbuf[0].inputstate |= INS_command | INS_DLE_command; */ - cs->inbuf[0].inputstate &= - ~(INS_command | INS_DLE_command); - break; - case ACT_SETDLE0: - cs->dle = 0; - cs->inbuf[0].inputstate = - (cs->inbuf[0].inputstate & ~INS_DLE_command) - | INS_command; - break; - case ACT_CMODESET: - if (cs->mstate == MS_INIT || cs->mstate == MS_RECOVER) { - gigaset_free_channels(cs); - cs->mstate = MS_READY; - } - cs->mode = M_CID; - cs->cur_at_seq = SEQ_NONE; - break; - case ACT_UMODESET: - cs->mode = M_UNIMODEM; - cs->cur_at_seq = SEQ_NONE; - break; - case ACT_FAILCMODE: - cs->cur_at_seq = SEQ_NONE; - if (cs->mstate == MS_INIT || cs->mstate == MS_RECOVER) { - init_failed(cs, M_UNKNOWN); - break; - } - if (reinit_and_retry(cs, -1) < 0) - schedule_init(cs, MS_RECOVER); - break; - case ACT_FAILUMODE: - cs->cur_at_seq = SEQ_NONE; - schedule_init(cs, MS_RECOVER); - break; - case ACT_HUPMODEM: - /* send "+++" (hangup in unimodem mode) */ - if (cs->connected) { - struct cmdbuf_t *cb; - - cb = kmalloc(sizeof(struct cmdbuf_t) + 3, GFP_ATOMIC); - if (!cb) { - dev_err(cs->dev, "%s: out of memory\n", - __func__); - return; - } - memcpy(cb->buf, "+++", 3); - cb->len = 3; - cb->offset = 0; - cb->next = NULL; - cb->wake_tasklet = NULL; - cs->ops->write_cmd(cs, cb); - } - break; - case ACT_RING: - /* get fresh AT state structure for new CID */ - at_state = get_free_channel(cs, ev->parameter); - if (!at_state) { - dev_warn(cs->dev, - "RING ignored: could not allocate channel structure\n"); - break; - } - - /* initialize AT state structure - * note that bcs may be NULL if no B channel is free - */ - at_state->ConState = 700; - for (i = 0; i < STR_NUM; ++i) { - kfree(at_state->str_var[i]); - at_state->str_var[i] = NULL; - } - at_state->int_var[VAR_ZCTP] = -1; - - spin_lock_irqsave(&cs->lock, flags); - at_state->timer_expires = RING_TIMEOUT; - at_state->timer_active = 1; - spin_unlock_irqrestore(&cs->lock, flags); - break; - case ACT_ICALL: - handle_icall(cs, bcs, at_state); - break; - case ACT_FAILSDOWN: - dev_warn(cs->dev, "Could not shut down the device.\n"); - /* fall through */ - case ACT_FAKESDOWN: - case ACT_SDOWN: - cs->cur_at_seq = SEQ_NONE; - finish_shutdown(cs); - break; - case ACT_CONNECT: - if (cs->onechannel) { - at_state->pending_commands |= PC_DLE1; - cs->commands_pending = 1; - break; - } - bcs->chstate |= CHS_D_UP; - gigaset_isdn_connD(bcs); - cs->ops->init_bchannel(bcs); - break; - case ACT_DLE1: - cs->cur_at_seq = SEQ_NONE; - bcs = cs->bcs + cs->curchannel; - - bcs->chstate |= CHS_D_UP; - gigaset_isdn_connD(bcs); - cs->ops->init_bchannel(bcs); - break; - case ACT_FAKEHUP: - at_state->int_var[VAR_ZSAU] = ZSAU_NULL; - /* fall through */ - case ACT_DISCONNECT: - cs->cur_at_seq = SEQ_NONE; - at_state->cid = -1; - if (!bcs) { - disconnect_nobc(p_at_state, cs); - } else if (cs->onechannel && cs->dle) { - /* Check for other open channels not needed: - * DLE only used for M10x with one B channel. - */ - at_state->pending_commands |= PC_DLE0; - cs->commands_pending = 1; - } else { - disconnect_bc(at_state, cs, bcs); - } - break; - case ACT_FAKEDLE0: - at_state->int_var[VAR_ZDLE] = 0; - cs->dle = 0; - /* fall through */ - case ACT_DLE0: - cs->cur_at_seq = SEQ_NONE; - bcs2 = cs->bcs + cs->curchannel; - disconnect_bc(&bcs2->at_state, cs, bcs2); - break; - case ACT_ABORTHUP: - cs->cur_at_seq = SEQ_NONE; - dev_warn(cs->dev, "Could not hang up.\n"); - at_state->cid = -1; - if (!bcs) - disconnect_nobc(p_at_state, cs); - else if (cs->onechannel) - at_state->pending_commands |= PC_DLE0; - else - disconnect_bc(at_state, cs, bcs); - schedule_init(cs, MS_RECOVER); - break; - case ACT_FAILDLE0: - cs->cur_at_seq = SEQ_NONE; - dev_warn(cs->dev, "Error leaving DLE mode.\n"); - cs->dle = 0; - bcs2 = cs->bcs + cs->curchannel; - disconnect_bc(&bcs2->at_state, cs, bcs2); - schedule_init(cs, MS_RECOVER); - break; - case ACT_FAILDLE1: - cs->cur_at_seq = SEQ_NONE; - dev_warn(cs->dev, - "Could not enter DLE mode. Trying to hang up.\n"); - channel = cs->curchannel; - cs->bcs[channel].at_state.pending_commands |= PC_HUP; - cs->commands_pending = 1; - break; - - case ACT_CID: /* got cid; start dialing */ - cs->cur_at_seq = SEQ_NONE; - channel = cs->curchannel; - if (ev->parameter > 0 && ev->parameter <= 65535) { - cs->bcs[channel].at_state.cid = ev->parameter; - cs->bcs[channel].at_state.pending_commands |= - PC_DIAL; - cs->commands_pending = 1; - break; - } - /* fall through - bad cid */ - case ACT_FAILCID: - cs->cur_at_seq = SEQ_NONE; - channel = cs->curchannel; - if (reinit_and_retry(cs, channel) < 0) { - dev_warn(cs->dev, - "Could not get a call ID. Cannot dial.\n"); - bcs2 = cs->bcs + channel; - disconnect_bc(&bcs2->at_state, cs, bcs2); - } - break; - case ACT_ABORTCID: - cs->cur_at_seq = SEQ_NONE; - bcs2 = cs->bcs + cs->curchannel; - disconnect_bc(&bcs2->at_state, cs, bcs2); - break; - - case ACT_DIALING: - case ACT_ACCEPTED: - cs->cur_at_seq = SEQ_NONE; - break; - - case ACT_ABORTACCEPT: /* hangup/error/timeout during ICALL procssng */ - if (bcs) - disconnect_bc(at_state, cs, bcs); - else - disconnect_nobc(p_at_state, cs); - break; - - case ACT_ABORTDIAL: /* error/timeout during dial preparation */ - cs->cur_at_seq = SEQ_NONE; - at_state->pending_commands |= PC_HUP; - cs->commands_pending = 1; - break; - - case ACT_REMOTEREJECT: /* DISCONNECT_IND after dialling */ - case ACT_CONNTIMEOUT: /* timeout waiting for ZSAU=ACTIVE */ - case ACT_REMOTEHUP: /* DISCONNECT_IND with established connection */ - at_state->pending_commands |= PC_HUP; - cs->commands_pending = 1; - break; - case ACT_GETSTRING: /* warning: RING, ZDLE, ... - are not handled properly anymore */ - at_state->getstring = 1; - break; - case ACT_SETVER: - if (!ev->ptr) { - *p_genresp = 1; - *p_resp_code = RSP_ERROR; - break; - } - s = ev->ptr; - - if (!strcmp(s, "OK")) { - /* OK without version string: assume old response */ - *p_genresp = 1; - *p_resp_code = RSP_NONE; - break; - } - - for (i = 0; i < 4; ++i) { - val = simple_strtoul(s, (char **) &e, 10); - if (val > INT_MAX || e == s) - break; - if (i == 3) { - if (*e) - break; - } else if (*e != '.') - break; - else - s = e + 1; - cs->fwver[i] = val; - } - if (i != 4) { - *p_genresp = 1; - *p_resp_code = RSP_ERROR; - break; - } - cs->gotfwver = 0; - break; - case ACT_GOTVER: - if (cs->gotfwver == 0) { - cs->gotfwver = 1; - gig_dbg(DEBUG_EVENT, - "firmware version %02d.%03d.%02d.%02d", - cs->fwver[0], cs->fwver[1], - cs->fwver[2], cs->fwver[3]); - break; - } - /* fall through */ - case ACT_FAILVER: - cs->gotfwver = -1; - dev_err(cs->dev, "could not read firmware version.\n"); - break; - case ACT_ERROR: - gig_dbg(DEBUG_ANY, "%s: ERROR response in ConState %d", - __func__, at_state->ConState); - cs->cur_at_seq = SEQ_NONE; - break; - case ACT_DEBUG: - gig_dbg(DEBUG_ANY, "%s: resp_code %d in ConState %d", - __func__, ev->type, at_state->ConState); - break; - case ACT_WARN: - dev_warn(cs->dev, "%s: resp_code %d in ConState %d!\n", - __func__, ev->type, at_state->ConState); - break; - case ACT_ZCAU: - dev_warn(cs->dev, "cause code %04x in connection state %d.\n", - ev->parameter, at_state->ConState); - break; - - /* events from the LL */ - - case ACT_DIAL: - if (!ev->ptr) { - *p_genresp = 1; - *p_resp_code = RSP_ERROR; - break; - } - start_dial(at_state, ev->ptr, ev->parameter); - break; - case ACT_ACCEPT: - start_accept(at_state); - break; - case ACT_HUP: - at_state->pending_commands |= PC_HUP; - gig_dbg(DEBUG_EVENT, "Scheduling PC_HUP"); - cs->commands_pending = 1; - break; - - /* hotplug events */ - - case ACT_STOP: - do_stop(cs); - break; - case ACT_START: - do_start(cs); - break; - - /* events from the interface */ - - case ACT_IF_LOCK: - cs->cmd_result = ev->parameter ? do_lock(cs) : do_unlock(cs); - cs->waiting = 0; - wake_up(&cs->waitqueue); - break; - case ACT_IF_VER: - if (ev->parameter != 0) - cs->cmd_result = -EINVAL; - else if (cs->gotfwver != 1) { - cs->cmd_result = -ENOENT; - } else { - memcpy(ev->arg, cs->fwver, sizeof cs->fwver); - cs->cmd_result = 0; - } - cs->waiting = 0; - wake_up(&cs->waitqueue); - break; - - /* events from the proc file system */ - - case ACT_PROC_CIDMODE: - spin_lock_irqsave(&cs->lock, flags); - if (ev->parameter != cs->cidmode) { - cs->cidmode = ev->parameter; - if (ev->parameter) { - cs->at_state.pending_commands |= PC_CIDMODE; - gig_dbg(DEBUG_EVENT, "Scheduling PC_CIDMODE"); - } else { - cs->at_state.pending_commands |= PC_UMMODE; - gig_dbg(DEBUG_EVENT, "Scheduling PC_UMMODE"); - } - cs->commands_pending = 1; - } - spin_unlock_irqrestore(&cs->lock, flags); - cs->waiting = 0; - wake_up(&cs->waitqueue); - break; - - /* events from the hardware drivers */ - - case ACT_NOTIFY_BC_DOWN: - bchannel_down(bcs); - break; - case ACT_NOTIFY_BC_UP: - bchannel_up(bcs); - break; - case ACT_SHUTDOWN: - do_shutdown(cs); - break; - - - default: - if (action >= ACT_CMD && action < ACT_CMD + AT_NUM) { - *pp_command = at_state->bcs->commands[action - ACT_CMD]; - if (!*pp_command) { - *p_genresp = 1; - *p_resp_code = RSP_NULL; - } - } else - dev_err(cs->dev, "%s: action==%d!\n", __func__, action); - } -} - -/* State machine to do the calling and hangup procedure */ -static void process_event(struct cardstate *cs, struct event_t *ev) -{ - struct bc_state *bcs; - char *p_command = NULL; - struct reply_t *rep; - int rcode; - int genresp = 0; - int resp_code = RSP_ERROR; - struct at_state_t *at_state; - int index; - int curact; - unsigned long flags; - - if (ev->cid >= 0) { - at_state = at_state_from_cid(cs, ev->cid); - if (!at_state) { - gig_dbg(DEBUG_EVENT, "event %d for invalid cid %d", - ev->type, ev->cid); - gigaset_add_event(cs, &cs->at_state, RSP_WRONG_CID, - NULL, 0, NULL); - return; - } - } else { - at_state = ev->at_state; - if (at_state_invalid(cs, at_state)) { - gig_dbg(DEBUG_EVENT, "event for invalid at_state %p", - at_state); - return; - } - } - - gig_dbg(DEBUG_EVENT, "connection state %d, event %d", - at_state->ConState, ev->type); - - bcs = at_state->bcs; - - /* Setting the pointer to the dial array */ - rep = at_state->replystruct; - - spin_lock_irqsave(&cs->lock, flags); - if (ev->type == EV_TIMEOUT) { - if (ev->parameter != at_state->timer_index - || !at_state->timer_active) { - ev->type = RSP_NONE; /* old timeout */ - gig_dbg(DEBUG_EVENT, "old timeout"); - } else { - if (at_state->waiting) - gig_dbg(DEBUG_EVENT, "stopped waiting"); - else - gig_dbg(DEBUG_EVENT, "timeout occurred"); - } - } - spin_unlock_irqrestore(&cs->lock, flags); - - /* if the response belongs to a variable in at_state->int_var[VAR_XXXX] - or at_state->str_var[STR_XXXX], set it */ - if (ev->type >= RSP_VAR && ev->type < RSP_VAR + VAR_NUM) { - index = ev->type - RSP_VAR; - at_state->int_var[index] = ev->parameter; - } else if (ev->type >= RSP_STR && ev->type < RSP_STR + STR_NUM) { - index = ev->type - RSP_STR; - kfree(at_state->str_var[index]); - at_state->str_var[index] = ev->ptr; - ev->ptr = NULL; /* prevent process_events() from - deallocating ptr */ - } - - if (ev->type == EV_TIMEOUT || ev->type == RSP_STRING) - at_state->getstring = 0; - - /* Search row in dial array which matches modem response and current - constate */ - for (;; rep++) { - rcode = rep->resp_code; - if (rcode == RSP_LAST) { - /* found nothing...*/ - dev_warn(cs->dev, "%s: rcode=RSP_LAST: " - "resp_code %d in ConState %d!\n", - __func__, ev->type, at_state->ConState); - return; - } - if ((rcode == RSP_ANY || rcode == ev->type) - && ((int) at_state->ConState >= rep->min_ConState) - && (rep->max_ConState < 0 - || (int) at_state->ConState <= rep->max_ConState) - && (rep->parameter < 0 || rep->parameter == ev->parameter)) - break; - } - - p_command = rep->command; - - at_state->waiting = 0; - for (curact = 0; curact < MAXACT; ++curact) { - /* The row tells us what we should do .. - */ - do_action(rep->action[curact], cs, bcs, &at_state, &p_command, - &genresp, &resp_code, ev); - if (!at_state) - /* at_state destroyed by disconnect */ - return; - } - - /* Jump to the next con-state regarding the array */ - if (rep->new_ConState >= 0) - at_state->ConState = rep->new_ConState; - - if (genresp) { - spin_lock_irqsave(&cs->lock, flags); - at_state->timer_expires = 0; - at_state->timer_active = 0; - spin_unlock_irqrestore(&cs->lock, flags); - gigaset_add_event(cs, at_state, resp_code, NULL, 0, NULL); - } else { - /* Send command to modem if not NULL... */ - if (p_command) { - if (cs->connected) - send_command(cs, p_command, at_state); - else - gigaset_add_event(cs, at_state, RSP_NODEV, - NULL, 0, NULL); - } - - spin_lock_irqsave(&cs->lock, flags); - if (!rep->timeout) { - at_state->timer_expires = 0; - at_state->timer_active = 0; - } else if (rep->timeout > 0) { /* new timeout */ - at_state->timer_expires = rep->timeout * 10; - at_state->timer_active = 1; - ++at_state->timer_index; - } - spin_unlock_irqrestore(&cs->lock, flags); - } -} - -static void schedule_sequence(struct cardstate *cs, - struct at_state_t *at_state, int sequence) -{ - cs->cur_at_seq = sequence; - gigaset_add_event(cs, at_state, RSP_INIT, NULL, sequence, NULL); -} - -static void process_command_flags(struct cardstate *cs) -{ - struct at_state_t *at_state = NULL; - struct bc_state *bcs; - int i; - int sequence; - unsigned long flags; - - cs->commands_pending = 0; - - if (cs->cur_at_seq) { - gig_dbg(DEBUG_EVENT, "not searching scheduled commands: busy"); - return; - } - - gig_dbg(DEBUG_EVENT, "searching scheduled commands"); - - sequence = SEQ_NONE; - - /* clear pending_commands and hangup channels on shutdown */ - if (cs->at_state.pending_commands & PC_SHUTDOWN) { - cs->at_state.pending_commands &= ~PC_CIDMODE; - for (i = 0; i < cs->channels; ++i) { - bcs = cs->bcs + i; - at_state = &bcs->at_state; - at_state->pending_commands &= - ~(PC_DLE1 | PC_ACCEPT | PC_DIAL); - if (at_state->cid > 0) - at_state->pending_commands |= PC_HUP; - if (at_state->pending_commands & PC_CID) { - at_state->pending_commands |= PC_NOCID; - at_state->pending_commands &= ~PC_CID; - } - } - } - - /* clear pending_commands and hangup channels on reset */ - if (cs->at_state.pending_commands & PC_INIT) { - cs->at_state.pending_commands &= ~PC_CIDMODE; - for (i = 0; i < cs->channels; ++i) { - bcs = cs->bcs + i; - at_state = &bcs->at_state; - at_state->pending_commands &= - ~(PC_DLE1 | PC_ACCEPT | PC_DIAL); - if (at_state->cid > 0) - at_state->pending_commands |= PC_HUP; - if (cs->mstate == MS_RECOVER) { - if (at_state->pending_commands & PC_CID) { - at_state->pending_commands |= PC_NOCID; - at_state->pending_commands &= ~PC_CID; - } - } - } - } - - /* only switch back to unimodem mode if no commands are pending and - * no channels are up */ - spin_lock_irqsave(&cs->lock, flags); - if (cs->at_state.pending_commands == PC_UMMODE - && !cs->cidmode - && list_empty(&cs->temp_at_states) - && cs->mode == M_CID) { - sequence = SEQ_UMMODE; - at_state = &cs->at_state; - for (i = 0; i < cs->channels; ++i) { - bcs = cs->bcs + i; - if (bcs->at_state.pending_commands || - bcs->at_state.cid > 0) { - sequence = SEQ_NONE; - break; - } - } - } - spin_unlock_irqrestore(&cs->lock, flags); - cs->at_state.pending_commands &= ~PC_UMMODE; - if (sequence != SEQ_NONE) { - schedule_sequence(cs, at_state, sequence); - return; - } - - for (i = 0; i < cs->channels; ++i) { - bcs = cs->bcs + i; - if (bcs->at_state.pending_commands & PC_HUP) { - if (cs->dle) { - cs->curchannel = bcs->channel; - schedule_sequence(cs, &cs->at_state, SEQ_DLE0); - return; - } - bcs->at_state.pending_commands &= ~PC_HUP; - if (bcs->at_state.pending_commands & PC_CID) { - /* not yet dialing: PC_NOCID is sufficient */ - bcs->at_state.pending_commands |= PC_NOCID; - bcs->at_state.pending_commands &= ~PC_CID; - } else { - schedule_sequence(cs, &bcs->at_state, SEQ_HUP); - return; - } - } - if (bcs->at_state.pending_commands & PC_NOCID) { - bcs->at_state.pending_commands &= ~PC_NOCID; - cs->curchannel = bcs->channel; - schedule_sequence(cs, &cs->at_state, SEQ_NOCID); - return; - } else if (bcs->at_state.pending_commands & PC_DLE0) { - bcs->at_state.pending_commands &= ~PC_DLE0; - cs->curchannel = bcs->channel; - schedule_sequence(cs, &cs->at_state, SEQ_DLE0); - return; - } - } - - list_for_each_entry(at_state, &cs->temp_at_states, list) - if (at_state->pending_commands & PC_HUP) { - at_state->pending_commands &= ~PC_HUP; - schedule_sequence(cs, at_state, SEQ_HUP); - return; - } - - if (cs->at_state.pending_commands & PC_INIT) { - cs->at_state.pending_commands &= ~PC_INIT; - cs->dle = 0; - cs->inbuf->inputstate = INS_command; - schedule_sequence(cs, &cs->at_state, SEQ_INIT); - return; - } - if (cs->at_state.pending_commands & PC_SHUTDOWN) { - cs->at_state.pending_commands &= ~PC_SHUTDOWN; - schedule_sequence(cs, &cs->at_state, SEQ_SHUTDOWN); - return; - } - if (cs->at_state.pending_commands & PC_CIDMODE) { - cs->at_state.pending_commands &= ~PC_CIDMODE; - if (cs->mode == M_UNIMODEM) { - cs->retry_count = 1; - schedule_sequence(cs, &cs->at_state, SEQ_CIDMODE); - return; - } - } - - for (i = 0; i < cs->channels; ++i) { - bcs = cs->bcs + i; - if (bcs->at_state.pending_commands & PC_DLE1) { - bcs->at_state.pending_commands &= ~PC_DLE1; - cs->curchannel = bcs->channel; - schedule_sequence(cs, &cs->at_state, SEQ_DLE1); - return; - } - if (bcs->at_state.pending_commands & PC_ACCEPT) { - bcs->at_state.pending_commands &= ~PC_ACCEPT; - schedule_sequence(cs, &bcs->at_state, SEQ_ACCEPT); - return; - } - if (bcs->at_state.pending_commands & PC_DIAL) { - bcs->at_state.pending_commands &= ~PC_DIAL; - schedule_sequence(cs, &bcs->at_state, SEQ_DIAL); - return; - } - if (bcs->at_state.pending_commands & PC_CID) { - switch (cs->mode) { - case M_UNIMODEM: - cs->at_state.pending_commands |= PC_CIDMODE; - gig_dbg(DEBUG_EVENT, "Scheduling PC_CIDMODE"); - cs->commands_pending = 1; - return; - case M_UNKNOWN: - schedule_init(cs, MS_INIT); - return; - } - bcs->at_state.pending_commands &= ~PC_CID; - cs->curchannel = bcs->channel; - cs->retry_count = 2; - schedule_sequence(cs, &cs->at_state, SEQ_CID); - return; - } - } -} - -static void process_events(struct cardstate *cs) -{ - struct event_t *ev; - unsigned head, tail; - int i; - int check_flags = 0; - int was_busy; - unsigned long flags; - - spin_lock_irqsave(&cs->ev_lock, flags); - head = cs->ev_head; - - for (i = 0; i < 2 * MAX_EVENTS; ++i) { - tail = cs->ev_tail; - if (tail == head) { - if (!check_flags && !cs->commands_pending) - break; - check_flags = 0; - spin_unlock_irqrestore(&cs->ev_lock, flags); - process_command_flags(cs); - spin_lock_irqsave(&cs->ev_lock, flags); - tail = cs->ev_tail; - if (tail == head) { - if (!cs->commands_pending) - break; - continue; - } - } - - ev = cs->events + head; - was_busy = cs->cur_at_seq != SEQ_NONE; - spin_unlock_irqrestore(&cs->ev_lock, flags); - process_event(cs, ev); - spin_lock_irqsave(&cs->ev_lock, flags); - kfree(ev->ptr); - ev->ptr = NULL; - if (was_busy && cs->cur_at_seq == SEQ_NONE) - check_flags = 1; - - head = (head + 1) % MAX_EVENTS; - cs->ev_head = head; - } - - spin_unlock_irqrestore(&cs->ev_lock, flags); - - if (i == 2 * MAX_EVENTS) { - dev_err(cs->dev, - "infinite loop in process_events; aborting.\n"); - } -} - -/* tasklet scheduled on any event received from the Gigaset device - * parameter: - * data ISDN controller state structure - */ -void gigaset_handle_event(unsigned long data) -{ - struct cardstate *cs = (struct cardstate *) data; - - /* handle incoming data on control/common channel */ - if (cs->inbuf->head != cs->inbuf->tail) { - gig_dbg(DEBUG_INTR, "processing new data"); - cs->ops->handle_input(cs->inbuf); - } - - process_events(cs); -} diff --git a/drivers/staging/isdn/gigaset/gigaset.h b/drivers/staging/isdn/gigaset/gigaset.h deleted file mode 100644 index 0ecc2b5ea553..000000000000 --- a/drivers/staging/isdn/gigaset/gigaset.h +++ /dev/null @@ -1,827 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0-or-later */ -/* - * Siemens Gigaset 307x driver - * Common header file for all connection variants - * - * Written by Stefan Eilers - * and Hansjoerg Lipp <hjlipp@web.de> - * - * ===================================================================== - * ===================================================================== - */ - -#ifndef GIGASET_H -#define GIGASET_H - -/* define global prefix for pr_ macros in linux/kernel.h */ -#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt - -#include <linux/kernel.h> -#include <linux/sched.h> -#include <linux/compiler.h> -#include <linux/types.h> -#include <linux/ctype.h> -#include <linux/slab.h> -#include <linux/spinlock.h> -#include <linux/skbuff.h> -#include <linux/netdevice.h> -#include <linux/ppp_defs.h> -#include <linux/timer.h> -#include <linux/interrupt.h> -#include <linux/tty.h> -#include <linux/tty_driver.h> -#include <linux/list.h> -#include <linux/atomic.h> - -#define GIG_VERSION {0, 5, 0, 0} -#define GIG_COMPAT {0, 4, 0, 0} - -#define MAX_REC_PARAMS 10 /* Max. number of params in response string */ -#define MAX_RESP_SIZE 511 /* Max. size of a response string */ - -#define MAX_EVENTS 64 /* size of event queue */ - -#define RBUFSIZE 8192 - -#define GIG_TICK 100 /* in milliseconds */ - -/* timeout values (unit: 1 sec) */ -#define INIT_TIMEOUT 1 - -/* timeout values (unit: 0.1 sec) */ -#define RING_TIMEOUT 3 /* for additional parameters to RING */ -#define BAS_TIMEOUT 20 /* for response to Base USB ops */ -#define ATRDY_TIMEOUT 3 /* for HD_READY_SEND_ATDATA */ - -#define BAS_RETRY 3 /* max. retries for base USB ops */ - -#define MAXACT 3 - -extern int gigaset_debuglevel; /* "needs" cast to (enum debuglevel) */ - -/* debug flags, combine by adding/bitwise OR */ -enum debuglevel { - DEBUG_INTR = 0x00008, /* interrupt processing */ - DEBUG_CMD = 0x00020, /* sent/received LL commands */ - DEBUG_STREAM = 0x00040, /* application data stream I/O events */ - DEBUG_STREAM_DUMP = 0x00080, /* application data stream content */ - DEBUG_LLDATA = 0x00100, /* sent/received LL data */ - DEBUG_EVENT = 0x00200, /* event processing */ - DEBUG_HDLC = 0x00800, /* M10x HDLC processing */ - DEBUG_CHANNEL = 0x01000, /* channel allocation/deallocation */ - DEBUG_TRANSCMD = 0x02000, /* AT-COMMANDS+RESPONSES */ - DEBUG_MCMD = 0x04000, /* COMMANDS THAT ARE SENT VERY OFTEN */ - DEBUG_INIT = 0x08000, /* (de)allocation+initialization of data - structures */ - DEBUG_SUSPEND = 0x10000, /* suspend/resume processing */ - DEBUG_OUTPUT = 0x20000, /* output to device */ - DEBUG_ISO = 0x40000, /* isochronous transfers */ - DEBUG_IF = 0x80000, /* character device operations */ - DEBUG_USBREQ = 0x100000, /* USB communication (except payload - data) */ - DEBUG_LOCKCMD = 0x200000, /* AT commands and responses when - MS_LOCKED */ - - DEBUG_ANY = 0x3fffff, /* print message if any of the others is - activated */ -}; - -#ifdef CONFIG_GIGASET_DEBUG - -#define gig_dbg(level, format, arg...) \ - do { \ - if (unlikely(((enum debuglevel)gigaset_debuglevel) & (level))) \ - printk(KERN_DEBUG KBUILD_MODNAME ": " format "\n", \ - ## arg); \ - } while (0) -#define DEBUG_DEFAULT (DEBUG_TRANSCMD | DEBUG_CMD | DEBUG_USBREQ) - -#else - -#define gig_dbg(level, format, arg...) do {} while (0) -#define DEBUG_DEFAULT 0 - -#endif - -void gigaset_dbg_buffer(enum debuglevel level, const unsigned char *msg, - size_t len, const unsigned char *buf); - -/* connection state */ -#define ZSAU_NONE 0 -#define ZSAU_PROCEEDING 1 -#define ZSAU_CALL_DELIVERED 2 -#define ZSAU_ACTIVE 3 -#define ZSAU_DISCONNECT_IND 4 -#define ZSAU_NULL 5 -#define ZSAU_DISCONNECT_REQ 6 -#define ZSAU_UNKNOWN -1 - -/* USB control transfer requests */ -#define OUT_VENDOR_REQ (USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_ENDPOINT) -#define IN_VENDOR_REQ (USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_ENDPOINT) - -/* interrupt pipe messages */ -#define HD_B1_FLOW_CONTROL 0x80 -#define HD_B2_FLOW_CONTROL 0x81 -#define HD_RECEIVEATDATA_ACK (0x35) /* 3070 */ -#define HD_READY_SEND_ATDATA (0x36) /* 3070 */ -#define HD_OPEN_ATCHANNEL_ACK (0x37) /* 3070 */ -#define HD_CLOSE_ATCHANNEL_ACK (0x38) /* 3070 */ -#define HD_DEVICE_INIT_OK (0x11) /* ISurf USB + 3070 */ -#define HD_OPEN_B1CHANNEL_ACK (0x51) /* ISurf USB + 3070 */ -#define HD_OPEN_B2CHANNEL_ACK (0x52) /* ISurf USB + 3070 */ -#define HD_CLOSE_B1CHANNEL_ACK (0x53) /* ISurf USB + 3070 */ -#define HD_CLOSE_B2CHANNEL_ACK (0x54) /* ISurf USB + 3070 */ -#define HD_SUSPEND_END (0x61) /* ISurf USB */ -#define HD_RESET_INTERRUPT_PIPE_ACK (0xFF) /* ISurf USB + 3070 */ - -/* control requests */ -#define HD_OPEN_B1CHANNEL (0x23) /* ISurf USB + 3070 */ -#define HD_CLOSE_B1CHANNEL (0x24) /* ISurf USB + 3070 */ -#define HD_OPEN_B2CHANNEL (0x25) /* ISurf USB + 3070 */ -#define HD_CLOSE_B2CHANNEL (0x26) /* ISurf USB + 3070 */ -#define HD_RESET_INTERRUPT_PIPE (0x27) /* ISurf USB + 3070 */ -#define HD_DEVICE_INIT_ACK (0x34) /* ISurf USB + 3070 */ -#define HD_WRITE_ATMESSAGE (0x12) /* 3070 */ -#define HD_READ_ATMESSAGE (0x13) /* 3070 */ -#define HD_OPEN_ATCHANNEL (0x28) /* 3070 */ -#define HD_CLOSE_ATCHANNEL (0x29) /* 3070 */ - -/* number of B channels supported by base driver */ -#define BAS_CHANNELS 2 - -/* USB frames for isochronous transfer */ -#define BAS_FRAMETIME 1 /* number of milliseconds between frames */ -#define BAS_NUMFRAMES 8 /* number of frames per URB */ -#define BAS_MAXFRAME 16 /* allocated bytes per frame */ -#define BAS_NORMFRAME 8 /* send size without flow control */ -#define BAS_HIGHFRAME 10 /* " " with positive flow control */ -#define BAS_LOWFRAME 5 /* " " with negative flow control */ -#define BAS_CORRFRAMES 4 /* flow control multiplicator */ - -#define BAS_INBUFSIZE (BAS_MAXFRAME * BAS_NUMFRAMES) /* size of isoc in buf - * per URB */ -#define BAS_OUTBUFSIZE 4096 /* size of common isoc out buffer */ -#define BAS_OUTBUFPAD BAS_MAXFRAME /* size of pad area for isoc out buf */ - -#define BAS_INURBS 3 -#define BAS_OUTURBS 3 - -/* variable commands in struct bc_state */ -#define AT_ISO 0 -#define AT_DIAL 1 -#define AT_MSN 2 -#define AT_BC 3 -#define AT_PROTO 4 -#define AT_TYPE 5 -#define AT_CLIP 6 -/* total number */ -#define AT_NUM 7 - -/* variables in struct at_state_t */ -/* - numeric */ -#define VAR_ZSAU 0 -#define VAR_ZDLE 1 -#define VAR_ZCTP 2 -/* total number */ -#define VAR_NUM 3 -/* - string */ -#define STR_NMBR 0 -#define STR_ZCPN 1 -#define STR_ZCON 2 -#define STR_ZBC 3 -#define STR_ZHLC 4 -/* total number */ -#define STR_NUM 5 - -/* event types */ -#define EV_TIMEOUT -105 -#define EV_IF_VER -106 -#define EV_PROC_CIDMODE -107 -#define EV_SHUTDOWN -108 -#define EV_START -110 -#define EV_STOP -111 -#define EV_IF_LOCK -112 -#define EV_ACCEPT -114 -#define EV_DIAL -115 -#define EV_HUP -116 -#define EV_BC_OPEN -117 -#define EV_BC_CLOSED -118 - -/* input state */ -#define INS_command 0x0001 /* receiving messages (not payload data) */ -#define INS_DLE_char 0x0002 /* DLE flag received (in DLE mode) */ -#define INS_byte_stuff 0x0004 -#define INS_have_data 0x0008 -#define INS_DLE_command 0x0020 /* DLE message start (<DLE> X) received */ -#define INS_flag_hunt 0x0040 - -/* channel state */ -#define CHS_D_UP 0x01 -#define CHS_B_UP 0x02 -#define CHS_NOTIFY_LL 0x04 - -#define ICALL_REJECT 0 -#define ICALL_ACCEPT 1 -#define ICALL_IGNORE 2 - -/* device state */ -#define MS_UNINITIALIZED 0 -#define MS_INIT 1 -#define MS_LOCKED 2 -#define MS_SHUTDOWN 3 -#define MS_RECOVER 4 -#define MS_READY 5 - -/* mode */ -#define M_UNKNOWN 0 -#define M_CONFIG 1 -#define M_UNIMODEM 2 -#define M_CID 3 - -/* start mode */ -#define SM_LOCKED 0 -#define SM_ISDN 1 /* default */ - -/* layer 2 protocols (AT^SBPR=...) */ -#define L2_BITSYNC 0 -#define L2_HDLC 1 -#define L2_VOICE 2 - -struct gigaset_ops; -struct gigaset_driver; - -struct usb_cardstate; -struct ser_cardstate; -struct bas_cardstate; - -struct bc_state; -struct usb_bc_state; -struct ser_bc_state; -struct bas_bc_state; - -struct reply_t { - int resp_code; /* RSP_XXXX */ - int min_ConState; /* <0 => ignore */ - int max_ConState; /* <0 => ignore */ - int parameter; /* e.g. ZSAU_XXXX <0: ignore*/ - int new_ConState; /* <0 => ignore */ - int timeout; /* >0 => *HZ; <=0 => TOUT_XXXX*/ - int action[MAXACT]; /* ACT_XXXX */ - char *command; /* NULL==none */ -}; - -extern struct reply_t gigaset_tab_cid[]; -extern struct reply_t gigaset_tab_nocid[]; - -struct inbuf_t { - struct cardstate *cs; - int inputstate; - int head, tail; - unsigned char data[RBUFSIZE]; -}; - -/* isochronous write buffer structure - * circular buffer with pad area for extraction of complete USB frames - * - data[read..nextread-1] is valid data already submitted to the USB subsystem - * - data[nextread..write-1] is valid data yet to be sent - * - data[write] is the next byte to write to - * - in byte-oriented L2 procotols, it is completely free - * - in bit-oriented L2 procotols, it may contain a partial byte of valid data - * - data[write+1..read-1] is free - * - wbits is the number of valid data bits in data[write], starting at the LSB - * - writesem is the semaphore for writing to the buffer: - * if writesem <= 0, data[write..read-1] is currently being written to - * - idle contains the byte value to repeat when the end of valid data is - * reached; if nextread==write (buffer contains no data to send), either the - * BAS_OUTBUFPAD bytes immediately before data[write] (if - * write>=BAS_OUTBUFPAD) or those of the pad area (if write<BAS_OUTBUFPAD) - * are also filled with that value - */ -struct isowbuf_t { - int read; - int nextread; - int write; - atomic_t writesem; - int wbits; - unsigned char data[BAS_OUTBUFSIZE + BAS_OUTBUFPAD]; - unsigned char idle; -}; - -/* isochronous write URB context structure - * data to be stored along with the URB and retrieved when it is returned - * as completed by the USB subsystem - * - urb: pointer to the URB itself - * - bcs: pointer to the B Channel control structure - * - limit: end of write buffer area covered by this URB - * - status: URB completion status - */ -struct isow_urbctx_t { - struct urb *urb; - struct bc_state *bcs; - int limit; - int status; -}; - -/* AT state structure - * data associated with the state of an ISDN connection, whether or not - * it is currently assigned a B channel - */ -struct at_state_t { - struct list_head list; - int waiting; - int getstring; - unsigned timer_index; - unsigned long timer_expires; - int timer_active; - unsigned int ConState; /* State of connection */ - struct reply_t *replystruct; - int cid; - int int_var[VAR_NUM]; /* see VAR_XXXX */ - char *str_var[STR_NUM]; /* see STR_XXXX */ - unsigned pending_commands; /* see PC_XXXX */ - unsigned seq_index; - - struct cardstate *cs; - struct bc_state *bcs; -}; - -struct event_t { - int type; - void *ptr, *arg; - int parameter; - int cid; - struct at_state_t *at_state; -}; - -/* This buffer holds all information about the used B-Channel */ -struct bc_state { - struct sk_buff *tx_skb; /* Current transfer buffer to modem */ - struct sk_buff_head squeue; /* B-Channel send Queue */ - - /* Variables for debugging .. */ - int corrupted; /* Counter for corrupted packages */ - int trans_down; /* Counter of packages (downstream) */ - int trans_up; /* Counter of packages (upstream) */ - - struct at_state_t at_state; - - /* receive buffer */ - unsigned rx_bufsize; /* max size accepted by application */ - struct sk_buff *rx_skb; - __u16 rx_fcs; - int inputstate; /* see INS_XXXX */ - - int channel; - - struct cardstate *cs; - - unsigned chstate; /* bitmap (CHS_*) */ - int ignore; - unsigned proto2; /* layer 2 protocol (L2_*) */ - char *commands[AT_NUM]; /* see AT_XXXX */ - -#ifdef CONFIG_GIGASET_DEBUG - int emptycount; -#endif - int busy; - int use_count; - - /* private data of hardware drivers */ - union { - struct ser_bc_state *ser; /* serial hardware driver */ - struct usb_bc_state *usb; /* usb hardware driver (m105) */ - struct bas_bc_state *bas; /* usb hardware driver (base) */ - } hw; - - void *ap; /* associated LL application */ - int apconnstate; /* LL application connection state */ - spinlock_t aplock; -}; - -struct cardstate { - struct gigaset_driver *driver; - unsigned minor_index; - struct device *dev; - struct device *tty_dev; - unsigned flags; - - const struct gigaset_ops *ops; - - /* Stuff to handle communication */ - wait_queue_head_t waitqueue; - int waiting; - int mode; /* see M_XXXX */ - int mstate; /* Modem state: see MS_XXXX */ - /* only changed by the event layer */ - int cmd_result; - - int channels; - struct bc_state *bcs; /* Array of struct bc_state */ - - int onechannel; /* data and commands transmitted in one - stream (M10x) */ - - spinlock_t lock; - struct at_state_t at_state; /* at_state_t for cid == 0 */ - struct list_head temp_at_states;/* list of temporary "struct - at_state_t"s without B channel */ - - struct inbuf_t *inbuf; - - struct cmdbuf_t *cmdbuf, *lastcmdbuf; - spinlock_t cmdlock; - unsigned curlen, cmdbytes; - - struct tty_port port; - struct tasklet_struct if_wake_tasklet; - unsigned control_state; - - unsigned fwver[4]; - int gotfwver; - - unsigned running; /* !=0 if events are handled */ - unsigned connected; /* !=0 if hardware is connected */ - unsigned isdn_up; /* !=0 after gigaset_isdn_start() */ - - unsigned cidmode; - - int myid; /* id for communication with LL */ - void *iif; /* LL interface structure */ - unsigned short hw_hdr_len; /* headroom needed in data skbs */ - - struct reply_t *tabnocid; - struct reply_t *tabcid; - int cs_init; - int ignoreframes; /* frames to ignore after setting up the - B channel */ - struct mutex mutex; /* locks this structure: - * connected is not changed, - * hardware_up is not changed, - * MState is not changed to or from - * MS_LOCKED */ - - struct timer_list timer; - int retry_count; - int dle; /* !=0 if DLE mode is active - (ZDLE=1 received -- M10x only) */ - int cur_at_seq; /* sequence of AT commands being - processed */ - int curchannel; /* channel those commands are meant - for */ - int commands_pending; /* flag(s) in xxx.commands_pending have - been set */ - struct tasklet_struct - event_tasklet; /* tasklet for serializing AT commands. - * Scheduled - * -> for modem reponses (and - * incoming data for M10x) - * -> on timeout - * -> after setting bits in - * xxx.at_state.pending_command - * (e.g. command from LL) */ - struct tasklet_struct - write_tasklet; /* tasklet for serial output - * (not used in base driver) */ - - /* event queue */ - struct event_t events[MAX_EVENTS]; - unsigned ev_tail, ev_head; - spinlock_t ev_lock; - - /* current modem response */ - unsigned char respdata[MAX_RESP_SIZE + 1]; - unsigned cbytes; - - /* private data of hardware drivers */ - union { - struct usb_cardstate *usb; /* USB hardware driver (m105) */ - struct ser_cardstate *ser; /* serial hardware driver */ - struct bas_cardstate *bas; /* USB hardware driver (base) */ - } hw; -}; - -struct gigaset_driver { - struct list_head list; - spinlock_t lock; /* locks minor tables and blocked */ - struct tty_driver *tty; - unsigned have_tty; - unsigned minor; - unsigned minors; - struct cardstate *cs; - int blocked; - - const struct gigaset_ops *ops; - struct module *owner; -}; - -struct cmdbuf_t { - struct cmdbuf_t *next, *prev; - int len, offset; - struct tasklet_struct *wake_tasklet; - unsigned char buf[0]; -}; - -struct bas_bc_state { - /* isochronous output state */ - int running; - atomic_t corrbytes; - spinlock_t isooutlock; - struct isow_urbctx_t isoouturbs[BAS_OUTURBS]; - struct isow_urbctx_t *isooutdone, *isooutfree, *isooutovfl; - struct isowbuf_t *isooutbuf; - unsigned numsub; /* submitted URB counter - (for diagnostic messages only) */ - struct tasklet_struct sent_tasklet; - - /* isochronous input state */ - spinlock_t isoinlock; - struct urb *isoinurbs[BAS_INURBS]; - unsigned char isoinbuf[BAS_INBUFSIZE * BAS_INURBS]; - struct urb *isoindone; /* completed isoc read URB */ - int isoinstatus; /* status of completed URB */ - int loststatus; /* status of dropped URB */ - unsigned isoinlost; /* number of bytes lost */ - /* state of bit unstuffing algorithm - (in addition to BC_state.inputstate) */ - unsigned seqlen; /* number of '1' bits not yet - unstuffed */ - unsigned inbyte, inbits; /* collected bits for next byte */ - /* statistics */ - unsigned goodbytes; /* bytes correctly received */ - unsigned alignerrs; /* frames with incomplete byte at end */ - unsigned fcserrs; /* FCS errors */ - unsigned frameerrs; /* framing errors */ - unsigned giants; /* long frames */ - unsigned runts; /* short frames */ - unsigned aborts; /* HDLC aborts */ - unsigned shared0s; /* '0' bits shared between flags */ - unsigned stolen0s; /* '0' stuff bits also serving as - leading flag bits */ - struct tasklet_struct rcvd_tasklet; -}; - -struct gigaset_ops { - /* Called from ev-layer.c/interface.c for sending AT commands to the - device */ - int (*write_cmd)(struct cardstate *cs, struct cmdbuf_t *cb); - - /* Called from interface.c for additional device control */ - int (*write_room)(struct cardstate *cs); - int (*chars_in_buffer)(struct cardstate *cs); - int (*brkchars)(struct cardstate *cs, const unsigned char buf[6]); - - /* Called from ev-layer.c after setting up connection - * Should call gigaset_bchannel_up(), when finished. */ - int (*init_bchannel)(struct bc_state *bcs); - - /* Called from ev-layer.c after hanging up - * Should call gigaset_bchannel_down(), when finished. */ - int (*close_bchannel)(struct bc_state *bcs); - - /* Called by gigaset_initcs() for setting up bcs->hw.xxx */ - int (*initbcshw)(struct bc_state *bcs); - - /* Called by gigaset_freecs() for freeing bcs->hw.xxx */ - void (*freebcshw)(struct bc_state *bcs); - - /* Called by gigaset_bchannel_down() for resetting bcs->hw.xxx */ - void (*reinitbcshw)(struct bc_state *bcs); - - /* Called by gigaset_initcs() for setting up cs->hw.xxx */ - int (*initcshw)(struct cardstate *cs); - - /* Called by gigaset_freecs() for freeing cs->hw.xxx */ - void (*freecshw)(struct cardstate *cs); - - /* Called from common.c/interface.c for additional serial port - control */ - int (*set_modem_ctrl)(struct cardstate *cs, unsigned old_state, - unsigned new_state); - int (*baud_rate)(struct cardstate *cs, unsigned cflag); - int (*set_line_ctrl)(struct cardstate *cs, unsigned cflag); - - /* Called from LL interface to put an skb into the send-queue. - * After sending is completed, gigaset_skb_sent() must be called - * with the skb's link layer header preserved. */ - int (*send_skb)(struct bc_state *bcs, struct sk_buff *skb); - - /* Called from ev-layer.c to process a block of data - * received through the common/control channel. */ - void (*handle_input)(struct inbuf_t *inbuf); - -}; - -/* = Common structures and definitions ======================================= - */ - -/* Parser states for DLE-Event: - * <DLE-EVENT>: <DLE_FLAG> "X" <EVENT> <DLE_FLAG> "." - * <DLE_FLAG>: 0x10 - * <EVENT>: ((a-z)* | (A-Z)* | (0-10)*)+ - */ -#define DLE_FLAG 0x10 - -/* =========================================================================== - * Functions implemented in asyncdata.c - */ - -/* Called from LL interface to put an skb into the send queue. */ -int gigaset_m10x_send_skb(struct bc_state *bcs, struct sk_buff *skb); - -/* Called from ev-layer.c to process a block of data - * received through the common/control channel. */ -void gigaset_m10x_input(struct inbuf_t *inbuf); - -/* =========================================================================== - * Functions implemented in isocdata.c - */ - -/* Called from LL interface to put an skb into the send queue. */ -int gigaset_isoc_send_skb(struct bc_state *bcs, struct sk_buff *skb); - -/* Called from ev-layer.c to process a block of data - * received through the common/control channel. */ -void gigaset_isoc_input(struct inbuf_t *inbuf); - -/* Called from bas-gigaset.c to process a block of data - * received through the isochronous channel */ -void gigaset_isoc_receive(unsigned char *src, unsigned count, - struct bc_state *bcs); - -/* Called from bas-gigaset.c to put a block of data - * into the isochronous output buffer */ -int gigaset_isoc_buildframe(struct bc_state *bcs, unsigned char *in, int len); - -/* Called from bas-gigaset.c to initialize the isochronous output buffer */ -void gigaset_isowbuf_init(struct isowbuf_t *iwb, unsigned char idle); - -/* Called from bas-gigaset.c to retrieve a block of bytes for sending */ -int gigaset_isowbuf_getbytes(struct isowbuf_t *iwb, int size); - -/* =========================================================================== - * Functions implemented in LL interface - */ - -/* Called from common.c for setting up/shutting down with the ISDN subsystem */ -void gigaset_isdn_regdrv(void); -void gigaset_isdn_unregdrv(void); -int gigaset_isdn_regdev(struct cardstate *cs, const char *isdnid); -void gigaset_isdn_unregdev(struct cardstate *cs); - -/* Called from hardware module to indicate completion of an skb */ -void gigaset_skb_sent(struct bc_state *bcs, struct sk_buff *skb); -void gigaset_skb_rcvd(struct bc_state *bcs, struct sk_buff *skb); -void gigaset_isdn_rcv_err(struct bc_state *bcs); - -/* Called from common.c/ev-layer.c to indicate events relevant to the LL */ -void gigaset_isdn_start(struct cardstate *cs); -void gigaset_isdn_stop(struct cardstate *cs); -int gigaset_isdn_icall(struct at_state_t *at_state); -void gigaset_isdn_connD(struct bc_state *bcs); -void gigaset_isdn_hupD(struct bc_state *bcs); -void gigaset_isdn_connB(struct bc_state *bcs); -void gigaset_isdn_hupB(struct bc_state *bcs); - -/* =========================================================================== - * Functions implemented in ev-layer.c - */ - -/* tasklet called from common.c to process queued events */ -void gigaset_handle_event(unsigned long data); - -/* called from isocdata.c / asyncdata.c - * when a complete modem response line has been received */ -void gigaset_handle_modem_response(struct cardstate *cs); - -/* =========================================================================== - * Functions implemented in proc.c - */ - -/* initialize sysfs for device */ -void gigaset_init_dev_sysfs(struct cardstate *cs); -void gigaset_free_dev_sysfs(struct cardstate *cs); - -/* =========================================================================== - * Functions implemented in common.c/gigaset.h - */ - -void gigaset_bcs_reinit(struct bc_state *bcs); -void gigaset_at_init(struct at_state_t *at_state, struct bc_state *bcs, - struct cardstate *cs, int cid); -int gigaset_get_channel(struct bc_state *bcs); -struct bc_state *gigaset_get_free_channel(struct cardstate *cs); -void gigaset_free_channel(struct bc_state *bcs); -int gigaset_get_channels(struct cardstate *cs); -void gigaset_free_channels(struct cardstate *cs); -void gigaset_block_channels(struct cardstate *cs); - -/* Allocate and initialize driver structure. */ -struct gigaset_driver *gigaset_initdriver(unsigned minor, unsigned minors, - const char *procname, - const char *devname, - const struct gigaset_ops *ops, - struct module *owner); - -/* Deallocate driver structure. */ -void gigaset_freedriver(struct gigaset_driver *drv); - -struct cardstate *gigaset_get_cs_by_tty(struct tty_struct *tty); -struct cardstate *gigaset_get_cs_by_id(int id); -void gigaset_blockdriver(struct gigaset_driver *drv); - -/* Allocate and initialize card state. Calls hardware dependent - gigaset_init[b]cs(). */ -struct cardstate *gigaset_initcs(struct gigaset_driver *drv, int channels, - int onechannel, int ignoreframes, - int cidmode, const char *modulename); - -/* Free card state. Calls hardware dependent gigaset_free[b]cs(). */ -void gigaset_freecs(struct cardstate *cs); - -/* Tell common.c that hardware and driver are ready. */ -int gigaset_start(struct cardstate *cs); - -/* Tell common.c that the device is not present any more. */ -void gigaset_stop(struct cardstate *cs); - -/* Tell common.c that the driver is being unloaded. */ -int gigaset_shutdown(struct cardstate *cs); - -/* Append event to the queue. - * Returns NULL on failure or a pointer to the event on success. - * ptr must be kmalloc()ed (and not be freed by the caller). - */ -struct event_t *gigaset_add_event(struct cardstate *cs, - struct at_state_t *at_state, int type, - void *ptr, int parameter, void *arg); - -/* Called on CONFIG1 command from frontend. */ -int gigaset_enterconfigmode(struct cardstate *cs); - -/* cs->lock must not be locked */ -static inline void gigaset_schedule_event(struct cardstate *cs) -{ - unsigned long flags; - spin_lock_irqsave(&cs->lock, flags); - if (cs->running) - tasklet_schedule(&cs->event_tasklet); - spin_unlock_irqrestore(&cs->lock, flags); -} - -/* Tell common.c that B channel has been closed. */ -/* cs->lock must not be locked */ -static inline void gigaset_bchannel_down(struct bc_state *bcs) -{ - gigaset_add_event(bcs->cs, &bcs->at_state, EV_BC_CLOSED, NULL, 0, NULL); - gigaset_schedule_event(bcs->cs); -} - -/* Tell common.c that B channel has been opened. */ -/* cs->lock must not be locked */ -static inline void gigaset_bchannel_up(struct bc_state *bcs) -{ - gigaset_add_event(bcs->cs, &bcs->at_state, EV_BC_OPEN, NULL, 0, NULL); - gigaset_schedule_event(bcs->cs); -} - -/* set up next receive skb for data mode */ -static inline struct sk_buff *gigaset_new_rx_skb(struct bc_state *bcs) -{ - struct cardstate *cs = bcs->cs; - unsigned short hw_hdr_len = cs->hw_hdr_len; - - if (bcs->ignore) { - bcs->rx_skb = NULL; - } else { - bcs->rx_skb = dev_alloc_skb(bcs->rx_bufsize + hw_hdr_len); - if (bcs->rx_skb == NULL) - dev_warn(cs->dev, "could not allocate skb\n"); - else - skb_reserve(bcs->rx_skb, hw_hdr_len); - } - return bcs->rx_skb; -} - -/* append received bytes to inbuf */ -int gigaset_fill_inbuf(struct inbuf_t *inbuf, const unsigned char *src, - unsigned numbytes); - -/* =========================================================================== - * Functions implemented in interface.c - */ - -/* initialize interface */ -void gigaset_if_initdriver(struct gigaset_driver *drv, const char *procname, - const char *devname); -/* release interface */ -void gigaset_if_freedriver(struct gigaset_driver *drv); -/* add minor */ -void gigaset_if_init(struct cardstate *cs); -/* remove minor */ -void gigaset_if_free(struct cardstate *cs); -/* device received data */ -void gigaset_if_receive(struct cardstate *cs, - unsigned char *buffer, size_t len); - -#endif diff --git a/drivers/staging/isdn/gigaset/interface.c b/drivers/staging/isdn/gigaset/interface.c deleted file mode 100644 index 9ddadd07e707..000000000000 --- a/drivers/staging/isdn/gigaset/interface.c +++ /dev/null @@ -1,613 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -/* - * interface to user space for the gigaset driver - * - * Copyright (c) 2004 by Hansjoerg Lipp <hjlipp@web.de> - * - * ===================================================================== - * ===================================================================== - */ - -#include "gigaset.h" -#include <linux/gigaset_dev.h> -#include <linux/tty_flip.h> -#include <linux/module.h> - -/*** our ioctls ***/ - -static int if_lock(struct cardstate *cs, int *arg) -{ - int cmd = *arg; - - gig_dbg(DEBUG_IF, "%u: if_lock (%d)", cs->minor_index, cmd); - - if (cmd > 1) - return -EINVAL; - - if (cmd < 0) { - *arg = cs->mstate == MS_LOCKED; - return 0; - } - - if (!cmd && cs->mstate == MS_LOCKED && cs->connected) { - cs->ops->set_modem_ctrl(cs, 0, TIOCM_DTR | TIOCM_RTS); - cs->ops->baud_rate(cs, B115200); - cs->ops->set_line_ctrl(cs, CS8); - cs->control_state = TIOCM_DTR | TIOCM_RTS; - } - - cs->waiting = 1; - if (!gigaset_add_event(cs, &cs->at_state, EV_IF_LOCK, - NULL, cmd, NULL)) { - cs->waiting = 0; - return -ENOMEM; - } - gigaset_schedule_event(cs); - - wait_event(cs->waitqueue, !cs->waiting); - - if (cs->cmd_result >= 0) { - *arg = cs->cmd_result; - return 0; - } - - return cs->cmd_result; -} - -static int if_version(struct cardstate *cs, unsigned arg[4]) -{ - static const unsigned version[4] = GIG_VERSION; - static const unsigned compat[4] = GIG_COMPAT; - unsigned cmd = arg[0]; - - gig_dbg(DEBUG_IF, "%u: if_version (%d)", cs->minor_index, cmd); - - switch (cmd) { - case GIGVER_DRIVER: - memcpy(arg, version, sizeof version); - return 0; - case GIGVER_COMPAT: - memcpy(arg, compat, sizeof compat); - return 0; - case GIGVER_FWBASE: - cs->waiting = 1; - if (!gigaset_add_event(cs, &cs->at_state, EV_IF_VER, - NULL, 0, arg)) { - cs->waiting = 0; - return -ENOMEM; - } - gigaset_schedule_event(cs); - - wait_event(cs->waitqueue, !cs->waiting); - - if (cs->cmd_result >= 0) - return 0; - - return cs->cmd_result; - default: - return -EINVAL; - } -} - -static int if_config(struct cardstate *cs, int *arg) -{ - gig_dbg(DEBUG_IF, "%u: if_config (%d)", cs->minor_index, *arg); - - if (*arg != 1) - return -EINVAL; - - if (cs->mstate != MS_LOCKED) - return -EBUSY; - - if (!cs->connected) { - pr_err("%s: not connected\n", __func__); - return -ENODEV; - } - - *arg = 0; - return gigaset_enterconfigmode(cs); -} - -/*** the terminal driver ***/ - -static int if_open(struct tty_struct *tty, struct file *filp) -{ - struct cardstate *cs; - - gig_dbg(DEBUG_IF, "%d+%d: %s()", - tty->driver->minor_start, tty->index, __func__); - - cs = gigaset_get_cs_by_tty(tty); - if (!cs || !try_module_get(cs->driver->owner)) - return -ENODEV; - - if (mutex_lock_interruptible(&cs->mutex)) { - module_put(cs->driver->owner); - return -ERESTARTSYS; - } - tty->driver_data = cs; - - ++cs->port.count; - - if (cs->port.count == 1) { - tty_port_tty_set(&cs->port, tty); - cs->port.low_latency = 1; - } - - mutex_unlock(&cs->mutex); - return 0; -} - -static void if_close(struct tty_struct *tty, struct file *filp) -{ - struct cardstate *cs = tty->driver_data; - - if (!cs) { /* happens if we didn't find cs in open */ - gig_dbg(DEBUG_IF, "%s: no cardstate", __func__); - return; - } - - gig_dbg(DEBUG_IF, "%u: %s()", cs->minor_index, __func__); - - mutex_lock(&cs->mutex); - - if (!cs->connected) - gig_dbg(DEBUG_IF, "not connected"); /* nothing to do */ - else if (!cs->port.count) - dev_warn(cs->dev, "%s: device not opened\n", __func__); - else if (!--cs->port.count) - tty_port_tty_set(&cs->port, NULL); - - mutex_unlock(&cs->mutex); - - module_put(cs->driver->owner); -} - -static int if_ioctl(struct tty_struct *tty, - unsigned int cmd, unsigned long arg) -{ - struct cardstate *cs = tty->driver_data; - int retval = -ENODEV; - int int_arg; - unsigned char buf[6]; - unsigned version[4]; - - gig_dbg(DEBUG_IF, "%u: %s(0x%x)", cs->minor_index, __func__, cmd); - - if (mutex_lock_interruptible(&cs->mutex)) - return -ERESTARTSYS; - - if (!cs->connected) { - gig_dbg(DEBUG_IF, "not connected"); - retval = -ENODEV; - } else { - retval = 0; - switch (cmd) { - case GIGASET_REDIR: - retval = get_user(int_arg, (int __user *) arg); - if (retval >= 0) - retval = if_lock(cs, &int_arg); - if (retval >= 0) - retval = put_user(int_arg, (int __user *) arg); - break; - case GIGASET_CONFIG: - retval = get_user(int_arg, (int __user *) arg); - if (retval >= 0) - retval = if_config(cs, &int_arg); - if (retval >= 0) - retval = put_user(int_arg, (int __user *) arg); - break; - case GIGASET_BRKCHARS: - retval = copy_from_user(&buf, - (const unsigned char __user *) arg, 6) - ? -EFAULT : 0; - if (retval >= 0) { - gigaset_dbg_buffer(DEBUG_IF, "GIGASET_BRKCHARS", - 6, buf); - retval = cs->ops->brkchars(cs, buf); - } - break; - case GIGASET_VERSION: - retval = copy_from_user(version, - (unsigned __user *) arg, sizeof version) - ? -EFAULT : 0; - if (retval >= 0) - retval = if_version(cs, version); - if (retval >= 0) - retval = copy_to_user((unsigned __user *) arg, - version, sizeof version) - ? -EFAULT : 0; - break; - default: - gig_dbg(DEBUG_IF, "%s: arg not supported - 0x%04x", - __func__, cmd); - retval = -ENOIOCTLCMD; - } - } - - mutex_unlock(&cs->mutex); - - return retval; -} - -#ifdef CONFIG_COMPAT -static long if_compat_ioctl(struct tty_struct *tty, - unsigned int cmd, unsigned long arg) -{ - return if_ioctl(tty, cmd, (unsigned long)compat_ptr(arg)); -} -#endif - -static int if_tiocmget(struct tty_struct *tty) -{ - struct cardstate *cs = tty->driver_data; - int retval; - - gig_dbg(DEBUG_IF, "%u: %s()", cs->minor_index, __func__); - - if (mutex_lock_interruptible(&cs->mutex)) - return -ERESTARTSYS; - - retval = cs->control_state & (TIOCM_RTS | TIOCM_DTR); - - mutex_unlock(&cs->mutex); - - return retval; -} - -static int if_tiocmset(struct tty_struct *tty, - unsigned int set, unsigned int clear) -{ - struct cardstate *cs = tty->driver_data; - int retval; - unsigned mc; - - gig_dbg(DEBUG_IF, "%u: %s(0x%x, 0x%x)", - cs->minor_index, __func__, set, clear); - - if (mutex_lock_interruptible(&cs->mutex)) - return -ERESTARTSYS; - - if (!cs->connected) { - gig_dbg(DEBUG_IF, "not connected"); - retval = -ENODEV; - } else { - mc = (cs->control_state | set) & ~clear & (TIOCM_RTS | TIOCM_DTR); - retval = cs->ops->set_modem_ctrl(cs, cs->control_state, mc); - cs->control_state = mc; - } - - mutex_unlock(&cs->mutex); - - return retval; -} - -static int if_write(struct tty_struct *tty, const unsigned char *buf, int count) -{ - struct cardstate *cs = tty->driver_data; - struct cmdbuf_t *cb; - int retval; - - gig_dbg(DEBUG_IF, "%u: %s()", cs->minor_index, __func__); - - if (mutex_lock_interruptible(&cs->mutex)) - return -ERESTARTSYS; - - if (!cs->connected) { - gig_dbg(DEBUG_IF, "not connected"); - retval = -ENODEV; - goto done; - } - if (cs->mstate != MS_LOCKED) { - dev_warn(cs->dev, "can't write to unlocked device\n"); - retval = -EBUSY; - goto done; - } - if (count <= 0) { - /* nothing to do */ - retval = 0; - goto done; - } - - cb = kmalloc(sizeof(struct cmdbuf_t) + count, GFP_KERNEL); - if (!cb) { - dev_err(cs->dev, "%s: out of memory\n", __func__); - retval = -ENOMEM; - goto done; - } - - memcpy(cb->buf, buf, count); - cb->len = count; - cb->offset = 0; - cb->next = NULL; - cb->wake_tasklet = &cs->if_wake_tasklet; - retval = cs->ops->write_cmd(cs, cb); -done: - mutex_unlock(&cs->mutex); - return retval; -} - -static int if_write_room(struct tty_struct *tty) -{ - struct cardstate *cs = tty->driver_data; - int retval; - - gig_dbg(DEBUG_IF, "%u: %s()", cs->minor_index, __func__); - - if (mutex_lock_interruptible(&cs->mutex)) - return -ERESTARTSYS; - - if (!cs->connected) { - gig_dbg(DEBUG_IF, "not connected"); - retval = -ENODEV; - } else if (cs->mstate != MS_LOCKED) { - dev_warn(cs->dev, "can't write to unlocked device\n"); - retval = -EBUSY; - } else - retval = cs->ops->write_room(cs); - - mutex_unlock(&cs->mutex); - - return retval; -} - -static int if_chars_in_buffer(struct tty_struct *tty) -{ - struct cardstate *cs = tty->driver_data; - int retval = 0; - - gig_dbg(DEBUG_IF, "%u: %s()", cs->minor_index, __func__); - - mutex_lock(&cs->mutex); - - if (!cs->connected) - gig_dbg(DEBUG_IF, "not connected"); - else if (cs->mstate != MS_LOCKED) - dev_warn(cs->dev, "can't write to unlocked device\n"); - else - retval = cs->ops->chars_in_buffer(cs); - - mutex_unlock(&cs->mutex); - - return retval; -} - -static void if_throttle(struct tty_struct *tty) -{ - struct cardstate *cs = tty->driver_data; - - gig_dbg(DEBUG_IF, "%u: %s()", cs->minor_index, __func__); - - mutex_lock(&cs->mutex); - - if (!cs->connected) - gig_dbg(DEBUG_IF, "not connected"); /* nothing to do */ - else - gig_dbg(DEBUG_IF, "%s: not implemented\n", __func__); - - mutex_unlock(&cs->mutex); -} - -static void if_unthrottle(struct tty_struct *tty) -{ - struct cardstate *cs = tty->driver_data; - - gig_dbg(DEBUG_IF, "%u: %s()", cs->minor_index, __func__); - - mutex_lock(&cs->mutex); - - if (!cs->connected) - gig_dbg(DEBUG_IF, "not connected"); /* nothing to do */ - else - gig_dbg(DEBUG_IF, "%s: not implemented\n", __func__); - - mutex_unlock(&cs->mutex); -} - -static void if_set_termios(struct tty_struct *tty, struct ktermios *old) -{ - struct cardstate *cs = tty->driver_data; - unsigned int iflag; - unsigned int cflag; - unsigned int old_cflag; - unsigned int control_state, new_state; - - gig_dbg(DEBUG_IF, "%u: %s()", cs->minor_index, __func__); - - mutex_lock(&cs->mutex); - - if (!cs->connected) { - gig_dbg(DEBUG_IF, "not connected"); - goto out; - } - - iflag = tty->termios.c_iflag; - cflag = tty->termios.c_cflag; - old_cflag = old ? old->c_cflag : cflag; - gig_dbg(DEBUG_IF, "%u: iflag %x cflag %x old %x", - cs->minor_index, iflag, cflag, old_cflag); - - /* get a local copy of the current port settings */ - control_state = cs->control_state; - - /* - * Update baud rate. - * Do not attempt to cache old rates and skip settings, - * disconnects screw such tricks up completely. - * Premature optimization is the root of all evil. - */ - - /* reassert DTR and (maybe) RTS on transition from B0 */ - if ((old_cflag & CBAUD) == B0) { - new_state = control_state | TIOCM_DTR; - /* don't set RTS if using hardware flow control */ - if (!(old_cflag & CRTSCTS)) - new_state |= TIOCM_RTS; - gig_dbg(DEBUG_IF, "%u: from B0 - set DTR%s", - cs->minor_index, - (new_state & TIOCM_RTS) ? " only" : "/RTS"); - cs->ops->set_modem_ctrl(cs, control_state, new_state); - control_state = new_state; - } - - cs->ops->baud_rate(cs, cflag & CBAUD); - - if ((cflag & CBAUD) == B0) { - /* Drop RTS and DTR */ - gig_dbg(DEBUG_IF, "%u: to B0 - drop DTR/RTS", cs->minor_index); - new_state = control_state & ~(TIOCM_DTR | TIOCM_RTS); - cs->ops->set_modem_ctrl(cs, control_state, new_state); - control_state = new_state; - } - - /* - * Update line control register (LCR) - */ - - cs->ops->set_line_ctrl(cs, cflag); - - /* save off the modified port settings */ - cs->control_state = control_state; - -out: - mutex_unlock(&cs->mutex); -} - -static const struct tty_operations if_ops = { - .open = if_open, - .close = if_close, - .ioctl = if_ioctl, -#ifdef CONFIG_COMPAT - .compat_ioctl = if_compat_ioctl, -#endif - .write = if_write, - .write_room = if_write_room, - .chars_in_buffer = if_chars_in_buffer, - .set_termios = if_set_termios, - .throttle = if_throttle, - .unthrottle = if_unthrottle, - .tiocmget = if_tiocmget, - .tiocmset = if_tiocmset, -}; - - -/* wakeup tasklet for the write operation */ -static void if_wake(unsigned long data) -{ - struct cardstate *cs = (struct cardstate *)data; - - tty_port_tty_wakeup(&cs->port); -} - -/*** interface to common ***/ - -void gigaset_if_init(struct cardstate *cs) -{ - struct gigaset_driver *drv; - - drv = cs->driver; - if (!drv->have_tty) - return; - - tasklet_init(&cs->if_wake_tasklet, if_wake, (unsigned long) cs); - - mutex_lock(&cs->mutex); - cs->tty_dev = tty_port_register_device(&cs->port, drv->tty, - cs->minor_index, NULL); - - if (!IS_ERR(cs->tty_dev)) - dev_set_drvdata(cs->tty_dev, cs); - else { - pr_warn("could not register device to the tty subsystem\n"); - cs->tty_dev = NULL; - } - mutex_unlock(&cs->mutex); -} - -void gigaset_if_free(struct cardstate *cs) -{ - struct gigaset_driver *drv; - - drv = cs->driver; - if (!drv->have_tty) - return; - - tasklet_disable(&cs->if_wake_tasklet); - tasklet_kill(&cs->if_wake_tasklet); - cs->tty_dev = NULL; - tty_unregister_device(drv->tty, cs->minor_index); -} - -/** - * gigaset_if_receive() - pass a received block of data to the tty device - * @cs: device descriptor structure. - * @buffer: received data. - * @len: number of bytes received. - * - * Called by asyncdata/isocdata if a block of data received from the - * device must be sent to userspace through the ttyG* device. - */ -void gigaset_if_receive(struct cardstate *cs, - unsigned char *buffer, size_t len) -{ - tty_insert_flip_string(&cs->port, buffer, len); - tty_flip_buffer_push(&cs->port); -} -EXPORT_SYMBOL_GPL(gigaset_if_receive); - -/* gigaset_if_initdriver - * Initialize tty interface. - * parameters: - * drv Driver - * procname Name of the driver (e.g. for /proc/tty/drivers) - * devname Name of the device files (prefix without minor number) - */ -void gigaset_if_initdriver(struct gigaset_driver *drv, const char *procname, - const char *devname) -{ - int ret; - struct tty_driver *tty; - - drv->have_tty = 0; - - drv->tty = tty = alloc_tty_driver(drv->minors); - if (tty == NULL) - goto enomem; - - tty->type = TTY_DRIVER_TYPE_SERIAL; - tty->subtype = SERIAL_TYPE_NORMAL; - tty->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV; - - tty->driver_name = procname; - tty->name = devname; - tty->minor_start = drv->minor; - - tty->init_termios = tty_std_termios; - tty->init_termios.c_cflag = B9600 | CS8 | CREAD | HUPCL | CLOCAL; - tty_set_operations(tty, &if_ops); - - ret = tty_register_driver(tty); - if (ret < 0) { - pr_err("error %d registering tty driver\n", ret); - goto error; - } - gig_dbg(DEBUG_IF, "tty driver initialized"); - drv->have_tty = 1; - return; - -enomem: - pr_err("out of memory\n"); -error: - if (drv->tty) - put_tty_driver(drv->tty); -} - -void gigaset_if_freedriver(struct gigaset_driver *drv) -{ - if (!drv->have_tty) - return; - - drv->have_tty = 0; - tty_unregister_driver(drv->tty); - put_tty_driver(drv->tty); -} diff --git a/drivers/staging/isdn/gigaset/isocdata.c b/drivers/staging/isdn/gigaset/isocdata.c deleted file mode 100644 index 3ecf6e33ed15..000000000000 --- a/drivers/staging/isdn/gigaset/isocdata.c +++ /dev/null @@ -1,1006 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -/* - * Common data handling layer for bas_gigaset - * - * Copyright (c) 2005 by Tilman Schmidt <tilman@imap.cc>, - * Hansjoerg Lipp <hjlipp@web.de>. - * - * ===================================================================== - * ===================================================================== - */ - -#include "gigaset.h" -#include <linux/crc-ccitt.h> -#include <linux/bitrev.h> - -/* access methods for isowbuf_t */ -/* ============================ */ - -/* initialize buffer structure - */ -void gigaset_isowbuf_init(struct isowbuf_t *iwb, unsigned char idle) -{ - iwb->read = 0; - iwb->nextread = 0; - iwb->write = 0; - atomic_set(&iwb->writesem, 1); - iwb->wbits = 0; - iwb->idle = idle; - memset(iwb->data + BAS_OUTBUFSIZE, idle, BAS_OUTBUFPAD); -} - -/* compute number of bytes which can be appended to buffer - * so that there is still room to append a maximum frame of flags - */ -static inline int isowbuf_freebytes(struct isowbuf_t *iwb) -{ - int read, write, freebytes; - - read = iwb->read; - write = iwb->write; - freebytes = read - write; - if (freebytes > 0) { - /* no wraparound: need padding space within regular area */ - return freebytes - BAS_OUTBUFPAD; - } else if (read < BAS_OUTBUFPAD) { - /* wraparound: can use space up to end of regular area */ - return BAS_OUTBUFSIZE - write; - } else { - /* following the wraparound yields more space */ - return freebytes + BAS_OUTBUFSIZE - BAS_OUTBUFPAD; - } -} - -/* start writing - * acquire the write semaphore - * return 0 if acquired, <0 if busy - */ -static inline int isowbuf_startwrite(struct isowbuf_t *iwb) -{ - if (!atomic_dec_and_test(&iwb->writesem)) { - atomic_inc(&iwb->writesem); - gig_dbg(DEBUG_ISO, "%s: couldn't acquire iso write semaphore", - __func__); - return -EBUSY; - } - gig_dbg(DEBUG_ISO, - "%s: acquired iso write semaphore, data[write]=%02x, nbits=%d", - __func__, iwb->data[iwb->write], iwb->wbits); - return 0; -} - -/* finish writing - * release the write semaphore - * returns the current write position - */ -static inline int isowbuf_donewrite(struct isowbuf_t *iwb) -{ - int write = iwb->write; - atomic_inc(&iwb->writesem); - return write; -} - -/* append bits to buffer without any checks - * - data contains bits to append, starting at LSB - * - nbits is number of bits to append (0..24) - * must be called with the write semaphore held - * If more than nbits bits are set in data, the extraneous bits are set in the - * buffer too, but the write position is only advanced by nbits. - */ -static inline void isowbuf_putbits(struct isowbuf_t *iwb, u32 data, int nbits) -{ - int write = iwb->write; - data <<= iwb->wbits; - data |= iwb->data[write]; - nbits += iwb->wbits; - while (nbits >= 8) { - iwb->data[write++] = data & 0xff; - write %= BAS_OUTBUFSIZE; - data >>= 8; - nbits -= 8; - } - iwb->wbits = nbits; - iwb->data[write] = data & 0xff; - iwb->write = write; -} - -/* put final flag on HDLC bitstream - * also sets the idle fill byte to the correspondingly shifted flag pattern - * must be called with the write semaphore held - */ -static inline void isowbuf_putflag(struct isowbuf_t *iwb) -{ - int write; - - /* add two flags, thus reliably covering one byte */ - isowbuf_putbits(iwb, 0x7e7e, 8); - /* recover the idle flag byte */ - write = iwb->write; - iwb->idle = iwb->data[write]; - gig_dbg(DEBUG_ISO, "idle fill byte %02x", iwb->idle); - /* mask extraneous bits in buffer */ - iwb->data[write] &= (1 << iwb->wbits) - 1; -} - -/* retrieve a block of bytes for sending - * The requested number of bytes is provided as a contiguous block. - * If necessary, the frame is filled to the requested number of bytes - * with the idle value. - * returns offset to frame, < 0 on busy or error - */ -int gigaset_isowbuf_getbytes(struct isowbuf_t *iwb, int size) -{ - int read, write, limit, src, dst; - unsigned char pbyte; - - read = iwb->nextread; - write = iwb->write; - if (likely(read == write)) { - /* return idle frame */ - return read < BAS_OUTBUFPAD ? - BAS_OUTBUFSIZE : read - BAS_OUTBUFPAD; - } - - limit = read + size; - gig_dbg(DEBUG_STREAM, "%s: read=%d write=%d limit=%d", - __func__, read, write, limit); -#ifdef CONFIG_GIGASET_DEBUG - if (unlikely(size < 0 || size > BAS_OUTBUFPAD)) { - pr_err("invalid size %d\n", size); - return -EINVAL; - } -#endif - - if (read < write) { - /* no wraparound in valid data */ - if (limit >= write) { - /* append idle frame */ - if (isowbuf_startwrite(iwb) < 0) - return -EBUSY; - /* write position could have changed */ - write = iwb->write; - if (limit >= write) { - pbyte = iwb->data[write]; /* save - partial byte */ - limit = write + BAS_OUTBUFPAD; - gig_dbg(DEBUG_STREAM, - "%s: filling %d->%d with %02x", - __func__, write, limit, iwb->idle); - if (write + BAS_OUTBUFPAD < BAS_OUTBUFSIZE) - memset(iwb->data + write, iwb->idle, - BAS_OUTBUFPAD); - else { - /* wraparound, fill entire pad area */ - memset(iwb->data + write, iwb->idle, - BAS_OUTBUFSIZE + BAS_OUTBUFPAD - - write); - limit = 0; - } - gig_dbg(DEBUG_STREAM, - "%s: restoring %02x at %d", - __func__, pbyte, limit); - iwb->data[limit] = pbyte; /* restore - partial byte */ - iwb->write = limit; - } - isowbuf_donewrite(iwb); - } - } else { - /* valid data wraparound */ - if (limit >= BAS_OUTBUFSIZE) { - /* copy wrapped part into pad area */ - src = 0; - dst = BAS_OUTBUFSIZE; - while (dst < limit && src < write) - iwb->data[dst++] = iwb->data[src++]; - if (dst <= limit) { - /* fill pad area with idle byte */ - memset(iwb->data + dst, iwb->idle, - BAS_OUTBUFSIZE + BAS_OUTBUFPAD - dst); - } - limit = src; - } - } - iwb->nextread = limit; - return read; -} - -/* dump_bytes - * write hex bytes to syslog for debugging - */ -static inline void dump_bytes(enum debuglevel level, const char *tag, - unsigned char *bytes, int count) -{ -#ifdef CONFIG_GIGASET_DEBUG - unsigned char c; - static char dbgline[3 * 32 + 1]; - int i = 0; - - if (!(gigaset_debuglevel & level)) - return; - - while (count-- > 0) { - if (i > sizeof(dbgline) - 4) { - dbgline[i] = '\0'; - gig_dbg(level, "%s:%s", tag, dbgline); - i = 0; - } - c = *bytes++; - dbgline[i] = (i && !(i % 12)) ? '-' : ' '; - i++; - dbgline[i++] = hex_asc_hi(c); - dbgline[i++] = hex_asc_lo(c); - } - dbgline[i] = '\0'; - gig_dbg(level, "%s:%s", tag, dbgline); -#endif -} - -/*============================================================================*/ - -/* bytewise HDLC bitstuffing via table lookup - * lookup table: 5 subtables for 0..4 preceding consecutive '1' bits - * index: 256*(number of preceding '1' bits) + (next byte to stuff) - * value: bit 9.. 0 = result bits - * bit 12..10 = number of trailing '1' bits in result - * bit 14..13 = number of bits added by stuffing - */ -static const u16 stufftab[5 * 256] = { -/* previous 1s = 0: */ - 0x0000, 0x0001, 0x0002, 0x0003, 0x0004, 0x0005, 0x0006, 0x0007, 0x0008, 0x0009, 0x000a, 0x000b, 0x000c, 0x000d, 0x000e, 0x000f, - 0x0010, 0x0011, 0x0012, 0x0013, 0x0014, 0x0015, 0x0016, 0x0017, 0x0018, 0x0019, 0x001a, 0x001b, 0x001c, 0x001d, 0x001e, 0x201f, - 0x0020, 0x0021, 0x0022, 0x0023, 0x0024, 0x0025, 0x0026, 0x0027, 0x0028, 0x0029, 0x002a, 0x002b, 0x002c, 0x002d, 0x002e, 0x002f, - 0x0030, 0x0031, 0x0032, 0x0033, 0x0034, 0x0035, 0x0036, 0x0037, 0x0038, 0x0039, 0x003a, 0x003b, 0x003c, 0x003d, 0x203e, 0x205f, - 0x0040, 0x0041, 0x0042, 0x0043, 0x0044, 0x0045, 0x0046, 0x0047, 0x0048, 0x0049, 0x004a, 0x004b, 0x004c, 0x004d, 0x004e, 0x004f, - 0x0050, 0x0051, 0x0052, 0x0053, 0x0054, 0x0055, 0x0056, 0x0057, 0x0058, 0x0059, 0x005a, 0x005b, 0x005c, 0x005d, 0x005e, 0x209f, - 0x0060, 0x0061, 0x0062, 0x0063, 0x0064, 0x0065, 0x0066, 0x0067, 0x0068, 0x0069, 0x006a, 0x006b, 0x006c, 0x006d, 0x006e, 0x006f, - 0x0070, 0x0071, 0x0072, 0x0073, 0x0074, 0x0075, 0x0076, 0x0077, 0x0078, 0x0079, 0x007a, 0x007b, 0x207c, 0x207d, 0x20be, 0x20df, - 0x0480, 0x0481, 0x0482, 0x0483, 0x0484, 0x0485, 0x0486, 0x0487, 0x0488, 0x0489, 0x048a, 0x048b, 0x048c, 0x048d, 0x048e, 0x048f, - 0x0490, 0x0491, 0x0492, 0x0493, 0x0494, 0x0495, 0x0496, 0x0497, 0x0498, 0x0499, 0x049a, 0x049b, 0x049c, 0x049d, 0x049e, 0x251f, - 0x04a0, 0x04a1, 0x04a2, 0x04a3, 0x04a4, 0x04a5, 0x04a6, 0x04a7, 0x04a8, 0x04a9, 0x04aa, 0x04ab, 0x04ac, 0x04ad, 0x04ae, 0x04af, - 0x04b0, 0x04b1, 0x04b2, 0x04b3, 0x04b4, 0x04b5, 0x04b6, 0x04b7, 0x04b8, 0x04b9, 0x04ba, 0x04bb, 0x04bc, 0x04bd, 0x253e, 0x255f, - 0x08c0, 0x08c1, 0x08c2, 0x08c3, 0x08c4, 0x08c5, 0x08c6, 0x08c7, 0x08c8, 0x08c9, 0x08ca, 0x08cb, 0x08cc, 0x08cd, 0x08ce, 0x08cf, - 0x08d0, 0x08d1, 0x08d2, 0x08d3, 0x08d4, 0x08d5, 0x08d6, 0x08d7, 0x08d8, 0x08d9, 0x08da, 0x08db, 0x08dc, 0x08dd, 0x08de, 0x299f, - 0x0ce0, 0x0ce1, 0x0ce2, 0x0ce3, 0x0ce4, 0x0ce5, 0x0ce6, 0x0ce7, 0x0ce8, 0x0ce9, 0x0cea, 0x0ceb, 0x0cec, 0x0ced, 0x0cee, 0x0cef, - 0x10f0, 0x10f1, 0x10f2, 0x10f3, 0x10f4, 0x10f5, 0x10f6, 0x10f7, 0x20f8, 0x20f9, 0x20fa, 0x20fb, 0x257c, 0x257d, 0x29be, 0x2ddf, - -/* previous 1s = 1: */ - 0x0000, 0x0001, 0x0002, 0x0003, 0x0004, 0x0005, 0x0006, 0x0007, 0x0008, 0x0009, 0x000a, 0x000b, 0x000c, 0x000d, 0x000e, 0x200f, - 0x0010, 0x0011, 0x0012, 0x0013, 0x0014, 0x0015, 0x0016, 0x0017, 0x0018, 0x0019, 0x001a, 0x001b, 0x001c, 0x001d, 0x001e, 0x202f, - 0x0020, 0x0021, 0x0022, 0x0023, 0x0024, 0x0025, 0x0026, 0x0027, 0x0028, 0x0029, 0x002a, 0x002b, 0x002c, 0x002d, 0x002e, 0x204f, - 0x0030, 0x0031, 0x0032, 0x0033, 0x0034, 0x0035, 0x0036, 0x0037, 0x0038, 0x0039, 0x003a, 0x003b, 0x003c, 0x003d, 0x203e, 0x206f, - 0x0040, 0x0041, 0x0042, 0x0043, 0x0044, 0x0045, 0x0046, 0x0047, 0x0048, 0x0049, 0x004a, 0x004b, 0x004c, 0x004d, 0x004e, 0x208f, - 0x0050, 0x0051, 0x0052, 0x0053, 0x0054, 0x0055, 0x0056, 0x0057, 0x0058, 0x0059, 0x005a, 0x005b, 0x005c, 0x005d, 0x005e, 0x20af, - 0x0060, 0x0061, 0x0062, 0x0063, 0x0064, 0x0065, 0x0066, 0x0067, 0x0068, 0x0069, 0x006a, 0x006b, 0x006c, 0x006d, 0x006e, 0x20cf, - 0x0070, 0x0071, 0x0072, 0x0073, 0x0074, 0x0075, 0x0076, 0x0077, 0x0078, 0x0079, 0x007a, 0x007b, 0x207c, 0x207d, 0x20be, 0x20ef, - 0x0480, 0x0481, 0x0482, 0x0483, 0x0484, 0x0485, 0x0486, 0x0487, 0x0488, 0x0489, 0x048a, 0x048b, 0x048c, 0x048d, 0x048e, 0x250f, - 0x0490, 0x0491, 0x0492, 0x0493, 0x0494, 0x0495, 0x0496, 0x0497, 0x0498, 0x0499, 0x049a, 0x049b, 0x049c, 0x049d, 0x049e, 0x252f, - 0x04a0, 0x04a1, 0x04a2, 0x04a3, 0x04a4, 0x04a5, 0x04a6, 0x04a7, 0x04a8, 0x04a9, 0x04aa, 0x04ab, 0x04ac, 0x04ad, 0x04ae, 0x254f, - 0x04b0, 0x04b1, 0x04b2, 0x04b3, 0x04b4, 0x04b5, 0x04b6, 0x04b7, 0x04b8, 0x04b9, 0x04ba, 0x04bb, 0x04bc, 0x04bd, 0x253e, 0x256f, - 0x08c0, 0x08c1, 0x08c2, 0x08c3, 0x08c4, 0x08c5, 0x08c6, 0x08c7, 0x08c8, 0x08c9, 0x08ca, 0x08cb, 0x08cc, 0x08cd, 0x08ce, 0x298f, - 0x08d0, 0x08d1, 0x08d2, 0x08d3, 0x08d4, 0x08d5, 0x08d6, 0x08d7, 0x08d8, 0x08d9, 0x08da, 0x08db, 0x08dc, 0x08dd, 0x08de, 0x29af, - 0x0ce0, 0x0ce1, 0x0ce2, 0x0ce3, 0x0ce4, 0x0ce5, 0x0ce6, 0x0ce7, 0x0ce8, 0x0ce9, 0x0cea, 0x0ceb, 0x0cec, 0x0ced, 0x0cee, 0x2dcf, - 0x10f0, 0x10f1, 0x10f2, 0x10f3, 0x10f4, 0x10f5, 0x10f6, 0x10f7, 0x20f8, 0x20f9, 0x20fa, 0x20fb, 0x257c, 0x257d, 0x29be, 0x31ef, - -/* previous 1s = 2: */ - 0x0000, 0x0001, 0x0002, 0x0003, 0x0004, 0x0005, 0x0006, 0x2007, 0x0008, 0x0009, 0x000a, 0x000b, 0x000c, 0x000d, 0x000e, 0x2017, - 0x0010, 0x0011, 0x0012, 0x0013, 0x0014, 0x0015, 0x0016, 0x2027, 0x0018, 0x0019, 0x001a, 0x001b, 0x001c, 0x001d, 0x001e, 0x2037, - 0x0020, 0x0021, 0x0022, 0x0023, 0x0024, 0x0025, 0x0026, 0x2047, 0x0028, 0x0029, 0x002a, 0x002b, 0x002c, 0x002d, 0x002e, 0x2057, - 0x0030, 0x0031, 0x0032, 0x0033, 0x0034, 0x0035, 0x0036, 0x2067, 0x0038, 0x0039, 0x003a, 0x003b, 0x003c, 0x003d, 0x203e, 0x2077, - 0x0040, 0x0041, 0x0042, 0x0043, 0x0044, 0x0045, 0x0046, 0x2087, 0x0048, 0x0049, 0x004a, 0x004b, 0x004c, 0x004d, 0x004e, 0x2097, - 0x0050, 0x0051, 0x0052, 0x0053, 0x0054, 0x0055, 0x0056, 0x20a7, 0x0058, 0x0059, 0x005a, 0x005b, 0x005c, 0x005d, 0x005e, 0x20b7, - 0x0060, 0x0061, 0x0062, 0x0063, 0x0064, 0x0065, 0x0066, 0x20c7, 0x0068, 0x0069, 0x006a, 0x006b, 0x006c, 0x006d, 0x006e, 0x20d7, - 0x0070, 0x0071, 0x0072, 0x0073, 0x0074, 0x0075, 0x0076, 0x20e7, 0x0078, 0x0079, 0x007a, 0x007b, 0x207c, 0x207d, 0x20be, 0x20f7, - 0x0480, 0x0481, 0x0482, 0x0483, 0x0484, 0x0485, 0x0486, 0x2507, 0x0488, 0x0489, 0x048a, 0x048b, 0x048c, 0x048d, 0x048e, 0x2517, - 0x0490, 0x0491, 0x0492, 0x0493, 0x0494, 0x0495, 0x0496, 0x2527, 0x0498, 0x0499, 0x049a, 0x049b, 0x049c, 0x049d, 0x049e, 0x2537, - 0x04a0, 0x04a1, 0x04a2, 0x04a3, 0x04a4, 0x04a5, 0x04a6, 0x2547, 0x04a8, 0x04a9, 0x04aa, 0x04ab, 0x04ac, 0x04ad, 0x04ae, 0x2557, - 0x04b0, 0x04b1, 0x04b2, 0x04b3, 0x04b4, 0x04b5, 0x04b6, 0x2567, 0x04b8, 0x04b9, 0x04ba, 0x04bb, 0x04bc, 0x04bd, 0x253e, 0x2577, - 0x08c0, 0x08c1, 0x08c2, 0x08c3, 0x08c4, 0x08c5, 0x08c6, 0x2987, 0x08c8, 0x08c9, 0x08ca, 0x08cb, 0x08cc, 0x08cd, 0x08ce, 0x2997, - 0x08d0, 0x08d1, 0x08d2, 0x08d3, 0x08d4, 0x08d5, 0x08d6, 0x29a7, 0x08d8, 0x08d9, 0x08da, 0x08db, 0x08dc, 0x08dd, 0x08de, 0x29b7, - 0x0ce0, 0x0ce1, 0x0ce2, 0x0ce3, 0x0ce4, 0x0ce5, 0x0ce6, 0x2dc7, 0x0ce8, 0x0ce9, 0x0cea, 0x0ceb, 0x0cec, 0x0ced, 0x0cee, 0x2dd7, - 0x10f0, 0x10f1, 0x10f2, 0x10f3, 0x10f4, 0x10f5, 0x10f6, 0x31e7, 0x20f8, 0x20f9, 0x20fa, 0x20fb, 0x257c, 0x257d, 0x29be, 0x41f7, - -/* previous 1s = 3: */ - 0x0000, 0x0001, 0x0002, 0x2003, 0x0004, 0x0005, 0x0006, 0x200b, 0x0008, 0x0009, 0x000a, 0x2013, 0x000c, 0x000d, 0x000e, 0x201b, - 0x0010, 0x0011, 0x0012, 0x2023, 0x0014, 0x0015, 0x0016, 0x202b, 0x0018, 0x0019, 0x001a, 0x2033, 0x001c, 0x001d, 0x001e, 0x203b, - 0x0020, 0x0021, 0x0022, 0x2043, 0x0024, 0x0025, 0x0026, 0x204b, 0x0028, 0x0029, 0x002a, 0x2053, 0x002c, 0x002d, 0x002e, 0x205b, - 0x0030, 0x0031, 0x0032, 0x2063, 0x0034, 0x0035, 0x0036, 0x206b, 0x0038, 0x0039, 0x003a, 0x2073, 0x003c, 0x003d, 0x203e, 0x207b, - 0x0040, 0x0041, 0x0042, 0x2083, 0x0044, 0x0045, 0x0046, 0x208b, 0x0048, 0x0049, 0x004a, 0x2093, 0x004c, 0x004d, 0x004e, 0x209b, - 0x0050, 0x0051, 0x0052, 0x20a3, 0x0054, 0x0055, 0x0056, 0x20ab, 0x0058, 0x0059, 0x005a, 0x20b3, 0x005c, 0x005d, 0x005e, 0x20bb, - 0x0060, 0x0061, 0x0062, 0x20c3, 0x0064, 0x0065, 0x0066, 0x20cb, 0x0068, 0x0069, 0x006a, 0x20d3, 0x006c, 0x006d, 0x006e, 0x20db, - 0x0070, 0x0071, 0x0072, 0x20e3, 0x0074, 0x0075, 0x0076, 0x20eb, 0x0078, 0x0079, 0x007a, 0x20f3, 0x207c, 0x207d, 0x20be, 0x40fb, - 0x0480, 0x0481, 0x0482, 0x2503, 0x0484, 0x0485, 0x0486, 0x250b, 0x0488, 0x0489, 0x048a, 0x2513, 0x048c, 0x048d, 0x048e, 0x251b, - 0x0490, 0x0491, 0x0492, 0x2523, 0x0494, 0x0495, 0x0496, 0x252b, 0x0498, 0x0499, 0x049a, 0x2533, 0x049c, 0x049d, 0x049e, 0x253b, - 0x04a0, 0x04a1, 0x04a2, 0x2543, 0x04a4, 0x04a5, 0x04a6, 0x254b, 0x04a8, 0x04a9, 0x04aa, 0x2553, 0x04ac, 0x04ad, 0x04ae, 0x255b, - 0x04b0, 0x04b1, 0x04b2, 0x2563, 0x04b4, 0x04b5, 0x04b6, 0x256b, 0x04b8, 0x04b9, 0x04ba, 0x2573, 0x04bc, 0x04bd, 0x253e, 0x257b, - 0x08c0, 0x08c1, 0x08c2, 0x2983, 0x08c4, 0x08c5, 0x08c6, 0x298b, 0x08c8, 0x08c9, 0x08ca, 0x2993, 0x08cc, 0x08cd, 0x08ce, 0x299b, - 0x08d0, 0x08d1, 0x08d2, 0x29a3, 0x08d4, 0x08d5, 0x08d6, 0x29ab, 0x08d8, 0x08d9, 0x08da, 0x29b3, 0x08dc, 0x08dd, 0x08de, 0x29bb, - 0x0ce0, 0x0ce1, 0x0ce2, 0x2dc3, 0x0ce4, 0x0ce5, 0x0ce6, 0x2dcb, 0x0ce8, 0x0ce9, 0x0cea, 0x2dd3, 0x0cec, 0x0ced, 0x0cee, 0x2ddb, - 0x10f0, 0x10f1, 0x10f2, 0x31e3, 0x10f4, 0x10f5, 0x10f6, 0x31eb, 0x20f8, 0x20f9, 0x20fa, 0x41f3, 0x257c, 0x257d, 0x29be, 0x46fb, - -/* previous 1s = 4: */ - 0x0000, 0x2001, 0x0002, 0x2005, 0x0004, 0x2009, 0x0006, 0x200d, 0x0008, 0x2011, 0x000a, 0x2015, 0x000c, 0x2019, 0x000e, 0x201d, - 0x0010, 0x2021, 0x0012, 0x2025, 0x0014, 0x2029, 0x0016, 0x202d, 0x0018, 0x2031, 0x001a, 0x2035, 0x001c, 0x2039, 0x001e, 0x203d, - 0x0020, 0x2041, 0x0022, 0x2045, 0x0024, 0x2049, 0x0026, 0x204d, 0x0028, 0x2051, 0x002a, 0x2055, 0x002c, 0x2059, 0x002e, 0x205d, - 0x0030, 0x2061, 0x0032, 0x2065, 0x0034, 0x2069, 0x0036, 0x206d, 0x0038, 0x2071, 0x003a, 0x2075, 0x003c, 0x2079, 0x203e, 0x407d, - 0x0040, 0x2081, 0x0042, 0x2085, 0x0044, 0x2089, 0x0046, 0x208d, 0x0048, 0x2091, 0x004a, 0x2095, 0x004c, 0x2099, 0x004e, 0x209d, - 0x0050, 0x20a1, 0x0052, 0x20a5, 0x0054, 0x20a9, 0x0056, 0x20ad, 0x0058, 0x20b1, 0x005a, 0x20b5, 0x005c, 0x20b9, 0x005e, 0x20bd, - 0x0060, 0x20c1, 0x0062, 0x20c5, 0x0064, 0x20c9, 0x0066, 0x20cd, 0x0068, 0x20d1, 0x006a, 0x20d5, 0x006c, 0x20d9, 0x006e, 0x20dd, - 0x0070, 0x20e1, 0x0072, 0x20e5, 0x0074, 0x20e9, 0x0076, 0x20ed, 0x0078, 0x20f1, 0x007a, 0x20f5, 0x207c, 0x40f9, 0x20be, 0x417d, - 0x0480, 0x2501, 0x0482, 0x2505, 0x0484, 0x2509, 0x0486, 0x250d, 0x0488, 0x2511, 0x048a, 0x2515, 0x048c, 0x2519, 0x048e, 0x251d, - 0x0490, 0x2521, 0x0492, 0x2525, 0x0494, 0x2529, 0x0496, 0x252d, 0x0498, 0x2531, 0x049a, 0x2535, 0x049c, 0x2539, 0x049e, 0x253d, - 0x04a0, 0x2541, 0x04a2, 0x2545, 0x04a4, 0x2549, 0x04a6, 0x254d, 0x04a8, 0x2551, 0x04aa, 0x2555, 0x04ac, 0x2559, 0x04ae, 0x255d, - 0x04b0, 0x2561, 0x04b2, 0x2565, 0x04b4, 0x2569, 0x04b6, 0x256d, 0x04b8, 0x2571, 0x04ba, 0x2575, 0x04bc, 0x2579, 0x253e, 0x467d, - 0x08c0, 0x2981, 0x08c2, 0x2985, 0x08c4, 0x2989, 0x08c6, 0x298d, 0x08c8, 0x2991, 0x08ca, 0x2995, 0x08cc, 0x2999, 0x08ce, 0x299d, - 0x08d0, 0x29a1, 0x08d2, 0x29a5, 0x08d4, 0x29a9, 0x08d6, 0x29ad, 0x08d8, 0x29b1, 0x08da, 0x29b5, 0x08dc, 0x29b9, 0x08de, 0x29bd, - 0x0ce0, 0x2dc1, 0x0ce2, 0x2dc5, 0x0ce4, 0x2dc9, 0x0ce6, 0x2dcd, 0x0ce8, 0x2dd1, 0x0cea, 0x2dd5, 0x0cec, 0x2dd9, 0x0cee, 0x2ddd, - 0x10f0, 0x31e1, 0x10f2, 0x31e5, 0x10f4, 0x31e9, 0x10f6, 0x31ed, 0x20f8, 0x41f1, 0x20fa, 0x41f5, 0x257c, 0x46f9, 0x29be, 0x4b7d -}; - -/* hdlc_bitstuff_byte - * perform HDLC bitstuffing for one input byte (8 bits, LSB first) - * parameters: - * cin input byte - * ones number of trailing '1' bits in result before this step - * iwb pointer to output buffer structure - * (write semaphore must be held) - * return value: - * number of trailing '1' bits in result after this step - */ - -static inline int hdlc_bitstuff_byte(struct isowbuf_t *iwb, unsigned char cin, - int ones) -{ - u16 stuff; - int shiftinc, newones; - - /* get stuffing information for input byte - * value: bit 9.. 0 = result bits - * bit 12..10 = number of trailing '1' bits in result - * bit 14..13 = number of bits added by stuffing - */ - stuff = stufftab[256 * ones + cin]; - shiftinc = (stuff >> 13) & 3; - newones = (stuff >> 10) & 7; - stuff &= 0x3ff; - - /* append stuffed byte to output stream */ - isowbuf_putbits(iwb, stuff, 8 + shiftinc); - return newones; -} - -/* hdlc_buildframe - * Perform HDLC framing with bitstuffing on a byte buffer - * The input buffer is regarded as a sequence of bits, starting with the least - * significant bit of the first byte and ending with the most significant bit - * of the last byte. A 16 bit FCS is appended as defined by RFC 1662. - * Whenever five consecutive '1' bits appear in the resulting bit sequence, a - * '0' bit is inserted after them. - * The resulting bit string and a closing flag pattern (PPP_FLAG, '01111110') - * are appended to the output buffer starting at the given bit position, which - * is assumed to already contain a leading flag. - * The output buffer must have sufficient length; count + count/5 + 6 bytes - * starting at *out are safe and are verified to be present. - * parameters: - * in input buffer - * count number of bytes in input buffer - * iwb pointer to output buffer structure - * (write semaphore must be held) - * return value: - * position of end of packet in output buffer on success, - * -EAGAIN if write semaphore busy or buffer full - */ - -static inline int hdlc_buildframe(struct isowbuf_t *iwb, - unsigned char *in, int count) -{ - int ones; - u16 fcs; - int end; - unsigned char c; - - if (isowbuf_freebytes(iwb) < count + count / 5 + 6 || - isowbuf_startwrite(iwb) < 0) { - gig_dbg(DEBUG_ISO, "%s: %d bytes free -> -EAGAIN", - __func__, isowbuf_freebytes(iwb)); - return -EAGAIN; - } - - dump_bytes(DEBUG_STREAM_DUMP, "snd data", in, count); - - /* bitstuff and checksum input data */ - fcs = PPP_INITFCS; - ones = 0; - while (count-- > 0) { - c = *in++; - ones = hdlc_bitstuff_byte(iwb, c, ones); - fcs = crc_ccitt_byte(fcs, c); - } - - /* bitstuff and append FCS - * (complemented, least significant byte first) */ - fcs ^= 0xffff; - ones = hdlc_bitstuff_byte(iwb, fcs & 0x00ff, ones); - ones = hdlc_bitstuff_byte(iwb, (fcs >> 8) & 0x00ff, ones); - - /* put closing flag and repeat byte for flag idle */ - isowbuf_putflag(iwb); - end = isowbuf_donewrite(iwb); - return end; -} - -/* trans_buildframe - * Append a block of 'transparent' data to the output buffer, - * inverting the bytes. - * The output buffer must have sufficient length; count bytes - * starting at *out are safe and are verified to be present. - * parameters: - * in input buffer - * count number of bytes in input buffer - * iwb pointer to output buffer structure - * (write semaphore must be held) - * return value: - * position of end of packet in output buffer on success, - * -EAGAIN if write semaphore busy or buffer full - */ - -static inline int trans_buildframe(struct isowbuf_t *iwb, - unsigned char *in, int count) -{ - int write; - unsigned char c; - - if (unlikely(count <= 0)) - return iwb->write; - - if (isowbuf_freebytes(iwb) < count || - isowbuf_startwrite(iwb) < 0) { - gig_dbg(DEBUG_ISO, "can't put %d bytes", count); - return -EAGAIN; - } - - gig_dbg(DEBUG_STREAM, "put %d bytes", count); - dump_bytes(DEBUG_STREAM_DUMP, "snd data", in, count); - - write = iwb->write; - do { - c = bitrev8(*in++); - iwb->data[write++] = c; - write %= BAS_OUTBUFSIZE; - } while (--count > 0); - iwb->write = write; - iwb->idle = c; - - return isowbuf_donewrite(iwb); -} - -int gigaset_isoc_buildframe(struct bc_state *bcs, unsigned char *in, int len) -{ - int result; - - switch (bcs->proto2) { - case L2_HDLC: - result = hdlc_buildframe(bcs->hw.bas->isooutbuf, in, len); - gig_dbg(DEBUG_ISO, "%s: %d bytes HDLC -> %d", - __func__, len, result); - break; - default: /* assume transparent */ - result = trans_buildframe(bcs->hw.bas->isooutbuf, in, len); - gig_dbg(DEBUG_ISO, "%s: %d bytes trans -> %d", - __func__, len, result); - } - return result; -} - -/* hdlc_putbyte - * append byte c to current skb of B channel structure *bcs, updating fcs - */ -static inline void hdlc_putbyte(unsigned char c, struct bc_state *bcs) -{ - bcs->rx_fcs = crc_ccitt_byte(bcs->rx_fcs, c); - if (bcs->rx_skb == NULL) - /* skipping */ - return; - if (bcs->rx_skb->len >= bcs->rx_bufsize) { - dev_warn(bcs->cs->dev, "received oversized packet discarded\n"); - bcs->hw.bas->giants++; - dev_kfree_skb_any(bcs->rx_skb); - bcs->rx_skb = NULL; - return; - } - __skb_put_u8(bcs->rx_skb, c); -} - -/* hdlc_flush - * drop partial HDLC data packet - */ -static inline void hdlc_flush(struct bc_state *bcs) -{ - /* clear skb or allocate new if not skipping */ - if (bcs->rx_skb != NULL) - skb_trim(bcs->rx_skb, 0); - else - gigaset_new_rx_skb(bcs); - - /* reset packet state */ - bcs->rx_fcs = PPP_INITFCS; -} - -/* hdlc_done - * process completed HDLC data packet - */ -static inline void hdlc_done(struct bc_state *bcs) -{ - struct cardstate *cs = bcs->cs; - struct sk_buff *procskb; - unsigned int len; - - if (unlikely(bcs->ignore)) { - bcs->ignore--; - hdlc_flush(bcs); - return; - } - procskb = bcs->rx_skb; - if (procskb == NULL) { - /* previous error */ - gig_dbg(DEBUG_ISO, "%s: skb=NULL", __func__); - gigaset_isdn_rcv_err(bcs); - } else if (procskb->len < 2) { - dev_notice(cs->dev, "received short frame (%d octets)\n", - procskb->len); - bcs->hw.bas->runts++; - dev_kfree_skb_any(procskb); - gigaset_isdn_rcv_err(bcs); - } else if (bcs->rx_fcs != PPP_GOODFCS) { - dev_notice(cs->dev, "frame check error\n"); - bcs->hw.bas->fcserrs++; - dev_kfree_skb_any(procskb); - gigaset_isdn_rcv_err(bcs); - } else { - len = procskb->len; - __skb_trim(procskb, len -= 2); /* subtract FCS */ - gig_dbg(DEBUG_ISO, "%s: good frame (%d octets)", __func__, len); - dump_bytes(DEBUG_STREAM_DUMP, - "rcv data", procskb->data, len); - bcs->hw.bas->goodbytes += len; - gigaset_skb_rcvd(bcs, procskb); - } - gigaset_new_rx_skb(bcs); - bcs->rx_fcs = PPP_INITFCS; -} - -/* hdlc_frag - * drop HDLC data packet with non-integral last byte - */ -static inline void hdlc_frag(struct bc_state *bcs, unsigned inbits) -{ - if (unlikely(bcs->ignore)) { - bcs->ignore--; - hdlc_flush(bcs); - return; - } - - dev_notice(bcs->cs->dev, "received partial byte (%d bits)\n", inbits); - bcs->hw.bas->alignerrs++; - gigaset_isdn_rcv_err(bcs); - __skb_trim(bcs->rx_skb, 0); - bcs->rx_fcs = PPP_INITFCS; -} - -/* bit counts lookup table for HDLC bit unstuffing - * index: input byte - * value: bit 0..3 = number of consecutive '1' bits starting from LSB - * bit 4..6 = number of consecutive '1' bits starting from MSB - * (replacing 8 by 7 to make it fit; the algorithm won't care) - * bit 7 set if there are 5 or more "interior" consecutive '1' bits - */ -static const unsigned char bitcounts[256] = { - 0x00, 0x01, 0x00, 0x02, 0x00, 0x01, 0x00, 0x03, 0x00, 0x01, 0x00, 0x02, 0x00, 0x01, 0x00, 0x04, - 0x00, 0x01, 0x00, 0x02, 0x00, 0x01, 0x00, 0x03, 0x00, 0x01, 0x00, 0x02, 0x00, 0x01, 0x00, 0x05, - 0x00, 0x01, 0x00, 0x02, 0x00, 0x01, 0x00, 0x03, 0x00, 0x01, 0x00, 0x02, 0x00, 0x01, 0x00, 0x04, - 0x00, 0x01, 0x00, 0x02, 0x00, 0x01, 0x00, 0x03, 0x00, 0x01, 0x00, 0x02, 0x00, 0x01, 0x80, 0x06, - 0x00, 0x01, 0x00, 0x02, 0x00, 0x01, 0x00, 0x03, 0x00, 0x01, 0x00, 0x02, 0x00, 0x01, 0x00, 0x04, - 0x00, 0x01, 0x00, 0x02, 0x00, 0x01, 0x00, 0x03, 0x00, 0x01, 0x00, 0x02, 0x00, 0x01, 0x00, 0x05, - 0x00, 0x01, 0x00, 0x02, 0x00, 0x01, 0x00, 0x03, 0x00, 0x01, 0x00, 0x02, 0x00, 0x01, 0x00, 0x04, - 0x00, 0x01, 0x00, 0x02, 0x00, 0x01, 0x00, 0x03, 0x00, 0x01, 0x00, 0x02, 0x80, 0x81, 0x80, 0x07, - 0x10, 0x11, 0x10, 0x12, 0x10, 0x11, 0x10, 0x13, 0x10, 0x11, 0x10, 0x12, 0x10, 0x11, 0x10, 0x14, - 0x10, 0x11, 0x10, 0x12, 0x10, 0x11, 0x10, 0x13, 0x10, 0x11, 0x10, 0x12, 0x10, 0x11, 0x10, 0x15, - 0x10, 0x11, 0x10, 0x12, 0x10, 0x11, 0x10, 0x13, 0x10, 0x11, 0x10, 0x12, 0x10, 0x11, 0x10, 0x14, - 0x10, 0x11, 0x10, 0x12, 0x10, 0x11, 0x10, 0x13, 0x10, 0x11, 0x10, 0x12, 0x10, 0x11, 0x90, 0x16, - 0x20, 0x21, 0x20, 0x22, 0x20, 0x21, 0x20, 0x23, 0x20, 0x21, 0x20, 0x22, 0x20, 0x21, 0x20, 0x24, - 0x20, 0x21, 0x20, 0x22, 0x20, 0x21, 0x20, 0x23, 0x20, 0x21, 0x20, 0x22, 0x20, 0x21, 0x20, 0x25, - 0x30, 0x31, 0x30, 0x32, 0x30, 0x31, 0x30, 0x33, 0x30, 0x31, 0x30, 0x32, 0x30, 0x31, 0x30, 0x34, - 0x40, 0x41, 0x40, 0x42, 0x40, 0x41, 0x40, 0x43, 0x50, 0x51, 0x50, 0x52, 0x60, 0x61, 0x70, 0x78 -}; - -/* hdlc_unpack - * perform HDLC frame processing (bit unstuffing, flag detection, FCS - * calculation) on a sequence of received data bytes (8 bits each, LSB first) - * pass on successfully received, complete frames as SKBs via gigaset_skb_rcvd - * notify of errors via gigaset_isdn_rcv_err - * tally frames, errors etc. in BC structure counters - * parameters: - * src received data - * count number of received bytes - * bcs receiving B channel structure - */ -static inline void hdlc_unpack(unsigned char *src, unsigned count, - struct bc_state *bcs) -{ - struct bas_bc_state *ubc = bcs->hw.bas; - int inputstate; - unsigned seqlen, inbyte, inbits; - - /* load previous state: - * inputstate = set of flag bits: - * - INS_flag_hunt: no complete opening flag received since connection - * setup or last abort - * - INS_have_data: at least one complete data byte received since last - * flag - * seqlen = number of consecutive '1' bits in last 7 input stream bits - * (0..7) - * inbyte = accumulated partial data byte (if !INS_flag_hunt) - * inbits = number of valid bits in inbyte, starting at LSB (0..6) - */ - inputstate = bcs->inputstate; - seqlen = ubc->seqlen; - inbyte = ubc->inbyte; - inbits = ubc->inbits; - - /* bit unstuffing a byte a time - * Take your time to understand this; it's straightforward but tedious. - * The "bitcounts" lookup table is used to speed up the counting of - * leading and trailing '1' bits. - */ - while (count--) { - unsigned char c = *src++; - unsigned char tabentry = bitcounts[c]; - unsigned lead1 = tabentry & 0x0f; - unsigned trail1 = (tabentry >> 4) & 0x0f; - - seqlen += lead1; - - if (unlikely(inputstate & INS_flag_hunt)) { - if (c == PPP_FLAG) { - /* flag-in-one */ - inputstate &= ~(INS_flag_hunt | INS_have_data); - inbyte = 0; - inbits = 0; - } else if (seqlen == 6 && trail1 != 7) { - /* flag completed & not followed by abort */ - inputstate &= ~(INS_flag_hunt | INS_have_data); - inbyte = c >> (lead1 + 1); - inbits = 7 - lead1; - if (trail1 >= 8) { - /* interior stuffing: - * omitting the MSB handles most cases, - * correct the incorrectly handled - * cases individually */ - inbits--; - switch (c) { - case 0xbe: - inbyte = 0x3f; - break; - } - } - } - /* else: continue flag-hunting */ - } else if (likely(seqlen < 5 && trail1 < 7)) { - /* streamlined case: 8 data bits, no stuffing */ - inbyte |= c << inbits; - hdlc_putbyte(inbyte & 0xff, bcs); - inputstate |= INS_have_data; - inbyte >>= 8; - /* inbits unchanged */ - } else if (likely(seqlen == 6 && inbits == 7 - lead1 && - trail1 + 1 == inbits && - !(inputstate & INS_have_data))) { - /* streamlined case: flag idle - state unchanged */ - } else if (unlikely(seqlen > 6)) { - /* abort sequence */ - ubc->aborts++; - hdlc_flush(bcs); - inputstate |= INS_flag_hunt; - } else if (seqlen == 6) { - /* closing flag, including (6 - lead1) '1's - * and one '0' from inbits */ - if (inbits > 7 - lead1) { - hdlc_frag(bcs, inbits + lead1 - 7); - inputstate &= ~INS_have_data; - } else { - if (inbits < 7 - lead1) - ubc->stolen0s++; - if (inputstate & INS_have_data) { - hdlc_done(bcs); - inputstate &= ~INS_have_data; - } - } - - if (c == PPP_FLAG) { - /* complete flag, LSB overlaps preceding flag */ - ubc->shared0s++; - inbits = 0; - inbyte = 0; - } else if (trail1 != 7) { - /* remaining bits */ - inbyte = c >> (lead1 + 1); - inbits = 7 - lead1; - if (trail1 >= 8) { - /* interior stuffing: - * omitting the MSB handles most cases, - * correct the incorrectly handled - * cases individually */ - inbits--; - switch (c) { - case 0xbe: - inbyte = 0x3f; - break; - } - } - } else { - /* abort sequence follows, - * skb already empty anyway */ - ubc->aborts++; - inputstate |= INS_flag_hunt; - } - } else { /* (seqlen < 6) && (seqlen == 5 || trail1 >= 7) */ - - if (c == PPP_FLAG) { - /* complete flag */ - if (seqlen == 5) - ubc->stolen0s++; - if (inbits) { - hdlc_frag(bcs, inbits); - inbits = 0; - inbyte = 0; - } else if (inputstate & INS_have_data) - hdlc_done(bcs); - inputstate &= ~INS_have_data; - } else if (trail1 == 7) { - /* abort sequence */ - ubc->aborts++; - hdlc_flush(bcs); - inputstate |= INS_flag_hunt; - } else { - /* stuffed data */ - if (trail1 < 7) { /* => seqlen == 5 */ - /* stuff bit at position lead1, - * no interior stuffing */ - unsigned char mask = (1 << lead1) - 1; - c = (c & mask) | ((c & ~mask) >> 1); - inbyte |= c << inbits; - inbits += 7; - } else if (seqlen < 5) { /* trail1 >= 8 */ - /* interior stuffing: - * omitting the MSB handles most cases, - * correct the incorrectly handled - * cases individually */ - switch (c) { - case 0xbe: - c = 0x7e; - break; - } - inbyte |= c << inbits; - inbits += 7; - } else { /* seqlen == 5 && trail1 >= 8 */ - - /* stuff bit at lead1 *and* interior - * stuffing -- unstuff individually */ - switch (c) { - case 0x7d: - c = 0x3f; - break; - case 0xbe: - c = 0x3f; - break; - case 0x3e: - c = 0x1f; - break; - case 0x7c: - c = 0x3e; - break; - } - inbyte |= c << inbits; - inbits += 6; - } - if (inbits >= 8) { - inbits -= 8; - hdlc_putbyte(inbyte & 0xff, bcs); - inputstate |= INS_have_data; - inbyte >>= 8; - } - } - } - seqlen = trail1 & 7; - } - - /* save new state */ - bcs->inputstate = inputstate; - ubc->seqlen = seqlen; - ubc->inbyte = inbyte; - ubc->inbits = inbits; -} - -/* trans_receive - * pass on received USB frame transparently as SKB via gigaset_skb_rcvd - * invert bytes - * tally frames, errors etc. in BC structure counters - * parameters: - * src received data - * count number of received bytes - * bcs receiving B channel structure - */ -static inline void trans_receive(unsigned char *src, unsigned count, - struct bc_state *bcs) -{ - struct sk_buff *skb; - int dobytes; - unsigned char *dst; - - if (unlikely(bcs->ignore)) { - bcs->ignore--; - return; - } - skb = bcs->rx_skb; - if (skb == NULL) { - skb = gigaset_new_rx_skb(bcs); - if (skb == NULL) - return; - } - dobytes = bcs->rx_bufsize - skb->len; - while (count > 0) { - dst = skb_put(skb, count < dobytes ? count : dobytes); - while (count > 0 && dobytes > 0) { - *dst++ = bitrev8(*src++); - count--; - dobytes--; - } - if (dobytes == 0) { - dump_bytes(DEBUG_STREAM_DUMP, - "rcv data", skb->data, skb->len); - bcs->hw.bas->goodbytes += skb->len; - gigaset_skb_rcvd(bcs, skb); - skb = gigaset_new_rx_skb(bcs); - if (skb == NULL) - return; - dobytes = bcs->rx_bufsize; - } - } -} - -void gigaset_isoc_receive(unsigned char *src, unsigned count, - struct bc_state *bcs) -{ - switch (bcs->proto2) { - case L2_HDLC: - hdlc_unpack(src, count, bcs); - break; - default: /* assume transparent */ - trans_receive(src, count, bcs); - } -} - -/* == data input =========================================================== */ - -/* process a block of received bytes in command mode (mstate != MS_LOCKED) - * Append received bytes to the command response buffer and forward them - * line by line to the response handler. - * Note: Received lines may be terminated by CR, LF, or CR LF, which will be - * removed before passing the line to the response handler. - */ -static void cmd_loop(unsigned char *src, int numbytes, struct inbuf_t *inbuf) -{ - struct cardstate *cs = inbuf->cs; - unsigned cbytes = cs->cbytes; - unsigned char c; - - while (numbytes--) { - c = *src++; - switch (c) { - case '\n': - if (cbytes == 0 && cs->respdata[0] == '\r') { - /* collapse LF with preceding CR */ - cs->respdata[0] = 0; - break; - } - /* fall through */ - case '\r': - /* end of message line, pass to response handler */ - if (cbytes >= MAX_RESP_SIZE) { - dev_warn(cs->dev, "response too large (%d)\n", - cbytes); - cbytes = MAX_RESP_SIZE; - } - cs->cbytes = cbytes; - gigaset_dbg_buffer(DEBUG_TRANSCMD, "received response", - cbytes, cs->respdata); - gigaset_handle_modem_response(cs); - cbytes = 0; - - /* store EOL byte for CRLF collapsing */ - cs->respdata[0] = c; - break; - default: - /* append to line buffer if possible */ - if (cbytes < MAX_RESP_SIZE) - cs->respdata[cbytes] = c; - cbytes++; - } - } - - /* save state */ - cs->cbytes = cbytes; -} - - -/* process a block of data received through the control channel - */ -void gigaset_isoc_input(struct inbuf_t *inbuf) -{ - struct cardstate *cs = inbuf->cs; - unsigned tail, head, numbytes; - unsigned char *src; - - head = inbuf->head; - while (head != (tail = inbuf->tail)) { - gig_dbg(DEBUG_INTR, "buffer state: %u -> %u", head, tail); - if (head > tail) - tail = RBUFSIZE; - src = inbuf->data + head; - numbytes = tail - head; - gig_dbg(DEBUG_INTR, "processing %u bytes", numbytes); - - if (cs->mstate == MS_LOCKED) { - gigaset_dbg_buffer(DEBUG_LOCKCMD, "received response", - numbytes, src); - gigaset_if_receive(inbuf->cs, src, numbytes); - } else { - cmd_loop(src, numbytes, inbuf); - } - - head += numbytes; - if (head == RBUFSIZE) - head = 0; - gig_dbg(DEBUG_INTR, "setting head to %u", head); - inbuf->head = head; - } -} - - -/* == data output ========================================================== */ - -/** - * gigaset_isoc_send_skb() - queue an skb for sending - * @bcs: B channel descriptor structure. - * @skb: data to send. - * - * Called by LL to queue an skb for sending, and start transmission if - * necessary. - * Once the payload data has been transmitted completely, gigaset_skb_sent() - * will be called with the skb's link layer header preserved. - * - * Return value: - * number of bytes accepted for sending (skb->len) if ok, - * error code < 0 (eg. -ENODEV) on error - */ -int gigaset_isoc_send_skb(struct bc_state *bcs, struct sk_buff *skb) -{ - int len = skb->len; - unsigned long flags; - - spin_lock_irqsave(&bcs->cs->lock, flags); - if (!bcs->cs->connected) { - spin_unlock_irqrestore(&bcs->cs->lock, flags); - return -ENODEV; - } - - skb_queue_tail(&bcs->squeue, skb); - gig_dbg(DEBUG_ISO, "%s: skb queued, qlen=%d", - __func__, skb_queue_len(&bcs->squeue)); - - /* tasklet submits URB if necessary */ - tasklet_schedule(&bcs->hw.bas->sent_tasklet); - spin_unlock_irqrestore(&bcs->cs->lock, flags); - - return len; /* ok so far */ -} diff --git a/drivers/staging/isdn/gigaset/proc.c b/drivers/staging/isdn/gigaset/proc.c deleted file mode 100644 index 8914439a4237..000000000000 --- a/drivers/staging/isdn/gigaset/proc.c +++ /dev/null @@ -1,77 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -/* - * Stuff used by all variants of the driver - * - * Copyright (c) 2001 by Stefan Eilers, - * Hansjoerg Lipp <hjlipp@web.de>, - * Tilman Schmidt <tilman@imap.cc>. - * - * ===================================================================== - * ===================================================================== - */ - -#include "gigaset.h" - -static ssize_t show_cidmode(struct device *dev, - struct device_attribute *attr, char *buf) -{ - struct cardstate *cs = dev_get_drvdata(dev); - - return sprintf(buf, "%u\n", cs->cidmode); -} - -static ssize_t set_cidmode(struct device *dev, struct device_attribute *attr, - const char *buf, size_t count) -{ - struct cardstate *cs = dev_get_drvdata(dev); - long int value; - char *end; - - value = simple_strtol(buf, &end, 0); - while (*end) - if (!isspace(*end++)) - return -EINVAL; - if (value < 0 || value > 1) - return -EINVAL; - - if (mutex_lock_interruptible(&cs->mutex)) - return -ERESTARTSYS; - - cs->waiting = 1; - if (!gigaset_add_event(cs, &cs->at_state, EV_PROC_CIDMODE, - NULL, value, NULL)) { - cs->waiting = 0; - mutex_unlock(&cs->mutex); - return -ENOMEM; - } - gigaset_schedule_event(cs); - - wait_event(cs->waitqueue, !cs->waiting); - - mutex_unlock(&cs->mutex); - - return count; -} - -static DEVICE_ATTR(cidmode, S_IRUGO | S_IWUSR, show_cidmode, set_cidmode); - -/* free sysfs for device */ -void gigaset_free_dev_sysfs(struct cardstate *cs) -{ - if (!cs->tty_dev) - return; - - gig_dbg(DEBUG_INIT, "removing sysfs entries"); - device_remove_file(cs->tty_dev, &dev_attr_cidmode); -} - -/* initialize sysfs for device */ -void gigaset_init_dev_sysfs(struct cardstate *cs) -{ - if (!cs->tty_dev) - return; - - gig_dbg(DEBUG_INIT, "setting up sysfs"); - if (device_create_file(cs->tty_dev, &dev_attr_cidmode)) - pr_err("could not create sysfs attribute\n"); -} diff --git a/drivers/staging/isdn/gigaset/ser-gigaset.c b/drivers/staging/isdn/gigaset/ser-gigaset.c deleted file mode 100644 index 5587e9e7fc73..000000000000 --- a/drivers/staging/isdn/gigaset/ser-gigaset.c +++ /dev/null @@ -1,796 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -/* This is the serial hardware link layer (HLL) for the Gigaset 307x isdn - * DECT base (aka Sinus 45 isdn) using the RS232 DECT data module M101, - * written as a line discipline. - * - * ===================================================================== - * ===================================================================== - */ - -#include "gigaset.h" -#include <linux/module.h> -#include <linux/moduleparam.h> -#include <linux/platform_device.h> -#include <linux/completion.h> - -/* Version Information */ -#define DRIVER_AUTHOR "Tilman Schmidt" -#define DRIVER_DESC "Serial Driver for Gigaset 307x using Siemens M101" - -#define GIGASET_MINORS 1 -#define GIGASET_MINOR 0 -#define GIGASET_MODULENAME "ser_gigaset" -#define GIGASET_DEVNAME "ttyGS" - -/* length limit according to Siemens 3070usb-protokoll.doc ch. 2.1 */ -#define IF_WRITEBUF 264 - -MODULE_AUTHOR(DRIVER_AUTHOR); -MODULE_DESCRIPTION(DRIVER_DESC); -MODULE_LICENSE("GPL"); -MODULE_ALIAS_LDISC(N_GIGASET_M101); - -static int startmode = SM_ISDN; -module_param(startmode, int, S_IRUGO); -MODULE_PARM_DESC(startmode, "initial operation mode"); -static int cidmode = 1; -module_param(cidmode, int, S_IRUGO); -MODULE_PARM_DESC(cidmode, "stay in CID mode when idle"); - -static struct gigaset_driver *driver; - -struct ser_cardstate { - struct platform_device dev; - struct tty_struct *tty; - atomic_t refcnt; - struct completion dead_cmp; -}; - -static struct platform_driver device_driver = { - .driver = { - .name = GIGASET_MODULENAME, - }, -}; - -static void flush_send_queue(struct cardstate *); - -/* transmit data from current open skb - * result: number of bytes sent or error code < 0 - */ -static int write_modem(struct cardstate *cs) -{ - struct tty_struct *tty = cs->hw.ser->tty; - struct bc_state *bcs = &cs->bcs[0]; /* only one channel */ - struct sk_buff *skb = bcs->tx_skb; - int sent = -EOPNOTSUPP; - - WARN_ON(!tty || !tty->ops || !skb); - - if (!skb->len) { - dev_kfree_skb_any(skb); - bcs->tx_skb = NULL; - return -EINVAL; - } - - set_bit(TTY_DO_WRITE_WAKEUP, &tty->flags); - if (tty->ops->write) - sent = tty->ops->write(tty, skb->data, skb->len); - gig_dbg(DEBUG_OUTPUT, "write_modem: sent %d", sent); - if (sent < 0) { - /* error */ - flush_send_queue(cs); - return sent; - } - skb_pull(skb, sent); - if (!skb->len) { - /* skb sent completely */ - gigaset_skb_sent(bcs, skb); - - gig_dbg(DEBUG_INTR, "kfree skb (Adr: %lx)!", - (unsigned long) skb); - dev_kfree_skb_any(skb); - bcs->tx_skb = NULL; - } - return sent; -} - -/* - * transmit first queued command buffer - * result: number of bytes sent or error code < 0 - */ -static int send_cb(struct cardstate *cs) -{ - struct tty_struct *tty = cs->hw.ser->tty; - struct cmdbuf_t *cb, *tcb; - unsigned long flags; - int sent = 0; - - WARN_ON(!tty || !tty->ops); - - cb = cs->cmdbuf; - if (!cb) - return 0; /* nothing to do */ - - if (cb->len) { - set_bit(TTY_DO_WRITE_WAKEUP, &tty->flags); - sent = tty->ops->write(tty, cb->buf + cb->offset, cb->len); - if (sent < 0) { - /* error */ - gig_dbg(DEBUG_OUTPUT, "send_cb: write error %d", sent); - flush_send_queue(cs); - return sent; - } - cb->offset += sent; - cb->len -= sent; - gig_dbg(DEBUG_OUTPUT, "send_cb: sent %d, left %u, queued %u", - sent, cb->len, cs->cmdbytes); - } - - while (cb && !cb->len) { - spin_lock_irqsave(&cs->cmdlock, flags); - cs->cmdbytes -= cs->curlen; - tcb = cb; - cs->cmdbuf = cb = cb->next; - if (cb) { - cb->prev = NULL; - cs->curlen = cb->len; - } else { - cs->lastcmdbuf = NULL; - cs->curlen = 0; - } - spin_unlock_irqrestore(&cs->cmdlock, flags); - - if (tcb->wake_tasklet) - tasklet_schedule(tcb->wake_tasklet); - kfree(tcb); - } - return sent; -} - -/* - * send queue tasklet - * If there is already a skb opened, put data to the transfer buffer - * by calling "write_modem". - * Otherwise take a new skb out of the queue. - */ -static void gigaset_modem_fill(unsigned long data) -{ - struct cardstate *cs = (struct cardstate *) data; - struct bc_state *bcs; - struct sk_buff *nextskb; - int sent = 0; - - if (!cs) { - gig_dbg(DEBUG_OUTPUT, "%s: no cardstate", __func__); - return; - } - bcs = cs->bcs; - if (!bcs) { - gig_dbg(DEBUG_OUTPUT, "%s: no cardstate", __func__); - return; - } - if (!bcs->tx_skb) { - /* no skb is being sent; send command if any */ - sent = send_cb(cs); - gig_dbg(DEBUG_OUTPUT, "%s: send_cb -> %d", __func__, sent); - if (sent) - /* something sent or error */ - return; - - /* no command to send; get skb */ - nextskb = skb_dequeue(&bcs->squeue); - if (!nextskb) - /* no skb either, nothing to do */ - return; - bcs->tx_skb = nextskb; - - gig_dbg(DEBUG_INTR, "Dequeued skb (Adr: %lx)", - (unsigned long) bcs->tx_skb); - } - - /* send skb */ - gig_dbg(DEBUG_OUTPUT, "%s: tx_skb", __func__); - if (write_modem(cs) < 0) - gig_dbg(DEBUG_OUTPUT, "%s: write_modem failed", __func__); -} - -/* - * throw away all data queued for sending - */ -static void flush_send_queue(struct cardstate *cs) -{ - struct sk_buff *skb; - struct cmdbuf_t *cb; - unsigned long flags; - - /* command queue */ - spin_lock_irqsave(&cs->cmdlock, flags); - while ((cb = cs->cmdbuf) != NULL) { - cs->cmdbuf = cb->next; - if (cb->wake_tasklet) - tasklet_schedule(cb->wake_tasklet); - kfree(cb); - } - cs->cmdbuf = cs->lastcmdbuf = NULL; - cs->cmdbytes = cs->curlen = 0; - spin_unlock_irqrestore(&cs->cmdlock, flags); - - /* data queue */ - if (cs->bcs->tx_skb) - dev_kfree_skb_any(cs->bcs->tx_skb); - while ((skb = skb_dequeue(&cs->bcs->squeue)) != NULL) - dev_kfree_skb_any(skb); -} - - -/* Gigaset Driver Interface */ -/* ======================== */ - -/* - * queue an AT command string for transmission to the Gigaset device - * parameters: - * cs controller state structure - * buf buffer containing the string to send - * len number of characters to send - * wake_tasklet tasklet to run when transmission is complete, or NULL - * return value: - * number of bytes queued, or error code < 0 - */ -static int gigaset_write_cmd(struct cardstate *cs, struct cmdbuf_t *cb) -{ - unsigned long flags; - - gigaset_dbg_buffer(cs->mstate != MS_LOCKED ? - DEBUG_TRANSCMD : DEBUG_LOCKCMD, - "CMD Transmit", cb->len, cb->buf); - - spin_lock_irqsave(&cs->cmdlock, flags); - cb->prev = cs->lastcmdbuf; - if (cs->lastcmdbuf) - cs->lastcmdbuf->next = cb; - else { - cs->cmdbuf = cb; - cs->curlen = cb->len; - } - cs->cmdbytes += cb->len; - cs->lastcmdbuf = cb; - spin_unlock_irqrestore(&cs->cmdlock, flags); - - spin_lock_irqsave(&cs->lock, flags); - if (cs->connected) - tasklet_schedule(&cs->write_tasklet); - spin_unlock_irqrestore(&cs->lock, flags); - return cb->len; -} - -/* - * tty_driver.write_room interface routine - * return number of characters the driver will accept to be written - * parameter: - * controller state structure - * return value: - * number of characters - */ -static int gigaset_write_room(struct cardstate *cs) -{ - unsigned bytes; - - bytes = cs->cmdbytes; - return bytes < IF_WRITEBUF ? IF_WRITEBUF - bytes : 0; -} - -/* - * tty_driver.chars_in_buffer interface routine - * return number of characters waiting to be sent - * parameter: - * controller state structure - * return value: - * number of characters - */ -static int gigaset_chars_in_buffer(struct cardstate *cs) -{ - return cs->cmdbytes; -} - -/* - * implementation of ioctl(GIGASET_BRKCHARS) - * parameter: - * controller state structure - * return value: - * -EINVAL (unimplemented function) - */ -static int gigaset_brkchars(struct cardstate *cs, const unsigned char buf[6]) -{ - /* not implemented */ - return -EINVAL; -} - -/* - * Open B channel - * Called by "do_action" in ev-layer.c - */ -static int gigaset_init_bchannel(struct bc_state *bcs) -{ - /* nothing to do for M10x */ - gigaset_bchannel_up(bcs); - return 0; -} - -/* - * Close B channel - * Called by "do_action" in ev-layer.c - */ -static int gigaset_close_bchannel(struct bc_state *bcs) -{ - /* nothing to do for M10x */ - gigaset_bchannel_down(bcs); - return 0; -} - -/* - * Set up B channel structure - * This is called by "gigaset_initcs" in common.c - */ -static int gigaset_initbcshw(struct bc_state *bcs) -{ - /* unused */ - bcs->hw.ser = NULL; - return 0; -} - -/* - * Free B channel structure - * Called by "gigaset_freebcs" in common.c - */ -static void gigaset_freebcshw(struct bc_state *bcs) -{ - /* unused */ -} - -/* - * Reinitialize B channel structure - * This is called by "bcs_reinit" in common.c - */ -static void gigaset_reinitbcshw(struct bc_state *bcs) -{ - /* nothing to do for M10x */ -} - -/* - * Free hardware specific device data - * This will be called by "gigaset_freecs" in common.c - */ -static void gigaset_freecshw(struct cardstate *cs) -{ - tasklet_kill(&cs->write_tasklet); - if (!cs->hw.ser) - return; - platform_device_unregister(&cs->hw.ser->dev); -} - -static void gigaset_device_release(struct device *dev) -{ - kfree(container_of(dev, struct ser_cardstate, dev.dev)); -} - -/* - * Set up hardware specific device data - * This is called by "gigaset_initcs" in common.c - */ -static int gigaset_initcshw(struct cardstate *cs) -{ - int rc; - struct ser_cardstate *scs; - - scs = kzalloc(sizeof(struct ser_cardstate), GFP_KERNEL); - if (!scs) { - pr_err("out of memory\n"); - return -ENOMEM; - } - cs->hw.ser = scs; - - cs->hw.ser->dev.name = GIGASET_MODULENAME; - cs->hw.ser->dev.id = cs->minor_index; - cs->hw.ser->dev.dev.release = gigaset_device_release; - rc = platform_device_register(&cs->hw.ser->dev); - if (rc != 0) { - pr_err("error %d registering platform device\n", rc); - kfree(cs->hw.ser); - cs->hw.ser = NULL; - return rc; - } - - tasklet_init(&cs->write_tasklet, - gigaset_modem_fill, (unsigned long) cs); - return 0; -} - -/* - * set modem control lines - * Parameters: - * card state structure - * modem control line state ([TIOCM_DTR]|[TIOCM_RTS]) - * Called by "gigaset_start" and "gigaset_enterconfigmode" in common.c - * and by "if_lock" and "if_termios" in interface.c - */ -static int gigaset_set_modem_ctrl(struct cardstate *cs, unsigned old_state, - unsigned new_state) -{ - struct tty_struct *tty = cs->hw.ser->tty; - unsigned int set, clear; - - WARN_ON(!tty || !tty->ops); - /* tiocmset is an optional tty driver method */ - if (!tty->ops->tiocmset) - return -EINVAL; - set = new_state & ~old_state; - clear = old_state & ~new_state; - if (!set && !clear) - return 0; - gig_dbg(DEBUG_IF, "tiocmset set %x clear %x", set, clear); - return tty->ops->tiocmset(tty, set, clear); -} - -static int gigaset_baud_rate(struct cardstate *cs, unsigned cflag) -{ - return -EINVAL; -} - -static int gigaset_set_line_ctrl(struct cardstate *cs, unsigned cflag) -{ - return -EINVAL; -} - -static const struct gigaset_ops ops = { - .write_cmd = gigaset_write_cmd, - .write_room = gigaset_write_room, - .chars_in_buffer = gigaset_chars_in_buffer, - .brkchars = gigaset_brkchars, - .init_bchannel = gigaset_init_bchannel, - .close_bchannel = gigaset_close_bchannel, - .initbcshw = gigaset_initbcshw, - .freebcshw = gigaset_freebcshw, - .reinitbcshw = gigaset_reinitbcshw, - .initcshw = gigaset_initcshw, - .freecshw = gigaset_freecshw, - .set_modem_ctrl = gigaset_set_modem_ctrl, - .baud_rate = gigaset_baud_rate, - .set_line_ctrl = gigaset_set_line_ctrl, - .send_skb = gigaset_m10x_send_skb, /* asyncdata.c */ - .handle_input = gigaset_m10x_input, /* asyncdata.c */ -}; - - -/* Line Discipline Interface */ -/* ========================= */ - -/* helper functions for cardstate refcounting */ -static struct cardstate *cs_get(struct tty_struct *tty) -{ - struct cardstate *cs = tty->disc_data; - - if (!cs || !cs->hw.ser) { - gig_dbg(DEBUG_ANY, "%s: no cardstate", __func__); - return NULL; - } - atomic_inc(&cs->hw.ser->refcnt); - return cs; -} - -static void cs_put(struct cardstate *cs) -{ - if (atomic_dec_and_test(&cs->hw.ser->refcnt)) - complete(&cs->hw.ser->dead_cmp); -} - -/* - * Called by the tty driver when the line discipline is pushed onto the tty. - * Called in process context. - */ -static int -gigaset_tty_open(struct tty_struct *tty) -{ - struct cardstate *cs; - int rc; - - gig_dbg(DEBUG_INIT, "Starting HLL for Gigaset M101"); - - pr_info(DRIVER_DESC "\n"); - - if (!driver) { - pr_err("%s: no driver structure\n", __func__); - return -ENODEV; - } - - /* allocate memory for our device state and initialize it */ - cs = gigaset_initcs(driver, 1, 1, 0, cidmode, GIGASET_MODULENAME); - if (!cs) { - rc = -ENODEV; - goto error; - } - - cs->dev = &cs->hw.ser->dev.dev; - cs->hw.ser->tty = tty; - atomic_set(&cs->hw.ser->refcnt, 1); - init_completion(&cs->hw.ser->dead_cmp); - tty->disc_data = cs; - - /* Set the amount of data we're willing to receive per call - * from the hardware driver to half of the input buffer size - * to leave some reserve. - * Note: We don't do flow control towards the hardware driver. - * If more data is received than will fit into the input buffer, - * it will be dropped and an error will be logged. This should - * never happen as the device is slow and the buffer size ample. - */ - tty->receive_room = RBUFSIZE/2; - - /* OK.. Initialization of the datastructures and the HW is done.. Now - * startup system and notify the LL that we are ready to run - */ - if (startmode == SM_LOCKED) - cs->mstate = MS_LOCKED; - rc = gigaset_start(cs); - if (rc < 0) { - tasklet_kill(&cs->write_tasklet); - goto error; - } - - gig_dbg(DEBUG_INIT, "Startup of HLL done"); - return 0; - -error: - gig_dbg(DEBUG_INIT, "Startup of HLL failed"); - tty->disc_data = NULL; - gigaset_freecs(cs); - return rc; -} - -/* - * Called by the tty driver when the line discipline is removed. - * Called from process context. - */ -static void -gigaset_tty_close(struct tty_struct *tty) -{ - struct cardstate *cs = tty->disc_data; - - gig_dbg(DEBUG_INIT, "Stopping HLL for Gigaset M101"); - - if (!cs) { - gig_dbg(DEBUG_INIT, "%s: no cardstate", __func__); - return; - } - - /* prevent other callers from entering ldisc methods */ - tty->disc_data = NULL; - - if (!cs->hw.ser) - pr_err("%s: no hw cardstate\n", __func__); - else { - /* wait for running methods to finish */ - if (!atomic_dec_and_test(&cs->hw.ser->refcnt)) - wait_for_completion(&cs->hw.ser->dead_cmp); - } - - /* stop operations */ - gigaset_stop(cs); - tasklet_kill(&cs->write_tasklet); - flush_send_queue(cs); - cs->dev = NULL; - gigaset_freecs(cs); - - gig_dbg(DEBUG_INIT, "Shutdown of HLL done"); -} - -/* - * Called by the tty driver when the tty line is hung up. - * Wait for I/O to driver to complete and unregister ISDN device. - * This is already done by the close routine, so just call that. - * Called from process context. - */ -static int gigaset_tty_hangup(struct tty_struct *tty) -{ - gigaset_tty_close(tty); - return 0; -} - -/* - * Ioctl on the tty. - * Called in process context only. - * May be re-entered by multiple ioctl calling threads. - */ -static int -gigaset_tty_ioctl(struct tty_struct *tty, struct file *file, - unsigned int cmd, unsigned long arg) -{ - struct cardstate *cs = cs_get(tty); - int rc, val; - int __user *p = (int __user *)arg; - - if (!cs) - return -ENXIO; - - switch (cmd) { - - case FIONREAD: - /* unused, always return zero */ - val = 0; - rc = put_user(val, p); - break; - - case TCFLSH: - /* flush our buffers and the serial port's buffer */ - switch (arg) { - case TCIFLUSH: - /* no own input buffer to flush */ - break; - case TCIOFLUSH: - case TCOFLUSH: - flush_send_queue(cs); - break; - } - /* fall through */ - - default: - /* pass through to underlying serial device */ - rc = n_tty_ioctl_helper(tty, file, cmd, arg); - break; - } - cs_put(cs); - return rc; -} - -/* - * Called by the tty driver when a block of data has been received. - * Will not be re-entered while running but other ldisc functions - * may be called in parallel. - * Can be called from hard interrupt level as well as soft interrupt - * level or mainline. - * Parameters: - * tty tty structure - * buf buffer containing received characters - * cflags buffer containing error flags for received characters (ignored) - * count number of received characters - */ -static void -gigaset_tty_receive(struct tty_struct *tty, const unsigned char *buf, - char *cflags, int count) -{ - struct cardstate *cs = cs_get(tty); - unsigned tail, head, n; - struct inbuf_t *inbuf; - - if (!cs) - return; - inbuf = cs->inbuf; - if (!inbuf) { - dev_err(cs->dev, "%s: no inbuf\n", __func__); - cs_put(cs); - return; - } - - tail = inbuf->tail; - head = inbuf->head; - gig_dbg(DEBUG_INTR, "buffer state: %u -> %u, receive %u bytes", - head, tail, count); - - if (head <= tail) { - /* possible buffer wraparound */ - n = min_t(unsigned, count, RBUFSIZE - tail); - memcpy(inbuf->data + tail, buf, n); - tail = (tail + n) % RBUFSIZE; - buf += n; - count -= n; - } - - if (count > 0) { - /* tail < head and some data left */ - n = head - tail - 1; - if (count > n) { - dev_err(cs->dev, - "inbuf overflow, discarding %d bytes\n", - count - n); - count = n; - } - memcpy(inbuf->data + tail, buf, count); - tail += count; - } - - gig_dbg(DEBUG_INTR, "setting tail to %u", tail); - inbuf->tail = tail; - - /* Everything was received .. Push data into handler */ - gig_dbg(DEBUG_INTR, "%s-->BH", __func__); - gigaset_schedule_event(cs); - cs_put(cs); -} - -/* - * Called by the tty driver when there's room for more data to send. - */ -static void -gigaset_tty_wakeup(struct tty_struct *tty) -{ - struct cardstate *cs = cs_get(tty); - - clear_bit(TTY_DO_WRITE_WAKEUP, &tty->flags); - if (!cs) - return; - tasklet_schedule(&cs->write_tasklet); - cs_put(cs); -} - -static struct tty_ldisc_ops gigaset_ldisc = { - .owner = THIS_MODULE, - .magic = TTY_LDISC_MAGIC, - .name = "ser_gigaset", - .open = gigaset_tty_open, - .close = gigaset_tty_close, - .hangup = gigaset_tty_hangup, - .ioctl = gigaset_tty_ioctl, - .receive_buf = gigaset_tty_receive, - .write_wakeup = gigaset_tty_wakeup, -}; - - -/* Initialization / Shutdown */ -/* ========================= */ - -static int __init ser_gigaset_init(void) -{ - int rc; - - gig_dbg(DEBUG_INIT, "%s", __func__); - rc = platform_driver_register(&device_driver); - if (rc != 0) { - pr_err("error %d registering platform driver\n", rc); - return rc; - } - - /* allocate memory for our driver state and initialize it */ - driver = gigaset_initdriver(GIGASET_MINOR, GIGASET_MINORS, - GIGASET_MODULENAME, GIGASET_DEVNAME, - &ops, THIS_MODULE); - if (!driver) { - rc = -ENOMEM; - goto error; - } - - rc = tty_register_ldisc(N_GIGASET_M101, &gigaset_ldisc); - if (rc != 0) { - pr_err("error %d registering line discipline\n", rc); - goto error; - } - - return 0; - -error: - if (driver) { - gigaset_freedriver(driver); - driver = NULL; - } - platform_driver_unregister(&device_driver); - return rc; -} - -static void __exit ser_gigaset_exit(void) -{ - int rc; - - gig_dbg(DEBUG_INIT, "%s", __func__); - - if (driver) { - gigaset_freedriver(driver); - driver = NULL; - } - - rc = tty_unregister_ldisc(N_GIGASET_M101); - if (rc != 0) - pr_err("error %d unregistering line discipline\n", rc); - - platform_driver_unregister(&device_driver); -} - -module_init(ser_gigaset_init); -module_exit(ser_gigaset_exit); diff --git a/drivers/staging/isdn/gigaset/usb-gigaset.c b/drivers/staging/isdn/gigaset/usb-gigaset.c deleted file mode 100644 index a20c0bfa68f3..000000000000 --- a/drivers/staging/isdn/gigaset/usb-gigaset.c +++ /dev/null @@ -1,959 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -/* - * USB driver for Gigaset 307x directly or using M105 Data. - * - * Copyright (c) 2001 by Stefan Eilers - * and Hansjoerg Lipp <hjlipp@web.de>. - * - * This driver was derived from the USB skeleton driver by - * Greg Kroah-Hartman <greg@kroah.com> - * - * ===================================================================== - * ===================================================================== - */ - -#include "gigaset.h" -#include <linux/usb.h> -#include <linux/module.h> -#include <linux/moduleparam.h> - -/* Version Information */ -#define DRIVER_AUTHOR "Hansjoerg Lipp <hjlipp@web.de>, Stefan Eilers" -#define DRIVER_DESC "USB Driver for Gigaset 307x using M105" - -/* Module parameters */ - -static int startmode = SM_ISDN; -static int cidmode = 1; - -module_param(startmode, int, S_IRUGO); -module_param(cidmode, int, S_IRUGO); -MODULE_PARM_DESC(startmode, "start in isdn4linux mode"); -MODULE_PARM_DESC(cidmode, "Call-ID mode"); - -#define GIGASET_MINORS 1 -#define GIGASET_MINOR 8 -#define GIGASET_MODULENAME "usb_gigaset" -#define GIGASET_DEVNAME "ttyGU" - -/* length limit according to Siemens 3070usb-protokoll.doc ch. 2.1 */ -#define IF_WRITEBUF 264 - -/* Values for the Gigaset M105 Data */ -#define USB_M105_VENDOR_ID 0x0681 -#define USB_M105_PRODUCT_ID 0x0009 - -/* table of devices that work with this driver */ -static const struct usb_device_id gigaset_table[] = { - { USB_DEVICE(USB_M105_VENDOR_ID, USB_M105_PRODUCT_ID) }, - { } /* Terminating entry */ -}; - -MODULE_DEVICE_TABLE(usb, gigaset_table); - -/* - * Control requests (empty fields: 00) - * - * RT|RQ|VALUE|INDEX|LEN |DATA - * In: - * C1 08 01 - * Get flags (1 byte). Bits: 0=dtr,1=rts,3-7:? - * C1 0F ll ll - * Get device information/status (llll: 0x200 and 0x40 seen). - * Real size: I only saw MIN(llll,0x64). - * Contents: seems to be always the same... - * offset 0x00: Length of this structure (0x64) (len: 1,2,3 bytes) - * offset 0x3c: String (16 bit chars): "MCCI USB Serial V2.0" - * rest: ? - * Out: - * 41 11 - * Initialize/reset device ? - * 41 00 xx 00 - * ? (xx=00 or 01; 01 on start, 00 on close) - * 41 07 vv mm - * Set/clear flags vv=value, mm=mask (see RQ 08) - * 41 12 xx - * Used before the following configuration requests are issued - * (with xx=0x0f). I've seen other values<0xf, though. - * 41 01 xx xx - * Set baud rate. xxxx=ceil(0x384000/rate)=trunc(0x383fff/rate)+1. - * 41 03 ps bb - * Set byte size and parity. p: 0x20=even,0x10=odd,0x00=no parity - * [ 0x30: m, 0x40: s ] - * [s: 0: 1 stop bit; 1: 1.5; 2: 2] - * bb: bits/byte (seen 7 and 8) - * 41 13 -- -- -- -- 10 00 ww 00 00 00 xx 00 00 00 yy 00 00 00 zz 00 00 00 - * ?? - * Initialization: 01, 40, 00, 00 - * Open device: 00 40, 00, 00 - * yy and zz seem to be equal, either 0x00 or 0x0a - * (ww,xx) pairs seen: (00,00), (00,40), (01,40), (09,80), (19,80) - * 41 19 -- -- -- -- 06 00 00 00 00 xx 11 13 - * Used after every "configuration sequence" (RQ 12, RQs 01/03/13). - * xx is usually 0x00 but was 0x7e before starting data transfer - * in unimodem mode. So, this might be an array of characters that - * need special treatment ("commit all bufferd data"?), 11=^Q, 13=^S. - * - * Unimodem mode: use "modprobe ppp_async flag_time=0" as the device _needs_ two - * flags per packet. - */ - -/* functions called if a device of this driver is connected/disconnected */ -static int gigaset_probe(struct usb_interface *interface, - const struct usb_device_id *id); -static void gigaset_disconnect(struct usb_interface *interface); - -/* functions called before/after suspend */ -static int gigaset_suspend(struct usb_interface *intf, pm_message_t message); -static int gigaset_resume(struct usb_interface *intf); -static int gigaset_pre_reset(struct usb_interface *intf); - -static struct gigaset_driver *driver; - -/* usb specific object needed to register this driver with the usb subsystem */ -static struct usb_driver gigaset_usb_driver = { - .name = GIGASET_MODULENAME, - .probe = gigaset_probe, - .disconnect = gigaset_disconnect, - .id_table = gigaset_table, - .suspend = gigaset_suspend, - .resume = gigaset_resume, - .reset_resume = gigaset_resume, - .pre_reset = gigaset_pre_reset, - .post_reset = gigaset_resume, - .disable_hub_initiated_lpm = 1, -}; - -struct usb_cardstate { - struct usb_device *udev; /* usb device pointer */ - struct usb_interface *interface; /* interface for this device */ - int busy; /* bulk output in progress */ - - /* Output buffer */ - unsigned char *bulk_out_buffer; - int bulk_out_size; - int bulk_out_epnum; - struct urb *bulk_out_urb; - - /* Input buffer */ - unsigned char *rcvbuf; - int rcvbuf_size; - struct urb *read_urb; - - char bchars[6]; /* for request 0x19 */ -}; - -static inline unsigned tiocm_to_gigaset(unsigned state) -{ - return ((state & TIOCM_DTR) ? 1 : 0) | ((state & TIOCM_RTS) ? 2 : 0); -} - -static int gigaset_set_modem_ctrl(struct cardstate *cs, unsigned old_state, - unsigned new_state) -{ - struct usb_device *udev = cs->hw.usb->udev; - unsigned mask, val; - int r; - - mask = tiocm_to_gigaset(old_state ^ new_state); - val = tiocm_to_gigaset(new_state); - - gig_dbg(DEBUG_USBREQ, "set flags 0x%02x with mask 0x%02x", val, mask); - r = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), 7, 0x41, - (val & 0xff) | ((mask & 0xff) << 8), 0, - NULL, 0, 2000 /* timeout? */); - if (r < 0) - return r; - return 0; -} - -/* - * Set M105 configuration value - * using undocumented device commands reverse engineered from USB traces - * of the Siemens Windows driver - */ -static int set_value(struct cardstate *cs, u8 req, u16 val) -{ - struct usb_device *udev = cs->hw.usb->udev; - int r, r2; - - gig_dbg(DEBUG_USBREQ, "request %02x (%04x)", - (unsigned)req, (unsigned)val); - r = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), 0x12, 0x41, - 0xf /*?*/, 0, NULL, 0, 2000 /*?*/); - /* no idea what this does */ - if (r < 0) { - dev_err(&udev->dev, "error %d on request 0x12\n", -r); - return r; - } - - r = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), req, 0x41, - val, 0, NULL, 0, 2000 /*?*/); - if (r < 0) - dev_err(&udev->dev, "error %d on request 0x%02x\n", - -r, (unsigned)req); - - r2 = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), 0x19, 0x41, - 0, 0, cs->hw.usb->bchars, 6, 2000 /*?*/); - if (r2 < 0) - dev_err(&udev->dev, "error %d on request 0x19\n", -r2); - - return r < 0 ? r : (r2 < 0 ? r2 : 0); -} - -/* - * set the baud rate on the internal serial adapter - * using the undocumented parameter setting command - */ -static int gigaset_baud_rate(struct cardstate *cs, unsigned cflag) -{ - u16 val; - u32 rate; - - cflag &= CBAUD; - - switch (cflag) { - case B300: rate = 300; break; - case B600: rate = 600; break; - case B1200: rate = 1200; break; - case B2400: rate = 2400; break; - case B4800: rate = 4800; break; - case B9600: rate = 9600; break; - case B19200: rate = 19200; break; - case B38400: rate = 38400; break; - case B57600: rate = 57600; break; - case B115200: rate = 115200; break; - default: - rate = 9600; - dev_err(cs->dev, "unsupported baudrate request 0x%x," - " using default of B9600\n", cflag); - } - - val = 0x383fff / rate + 1; - - return set_value(cs, 1, val); -} - -/* - * set the line format on the internal serial adapter - * using the undocumented parameter setting command - */ -static int gigaset_set_line_ctrl(struct cardstate *cs, unsigned cflag) -{ - u16 val = 0; - - /* set the parity */ - if (cflag & PARENB) - val |= (cflag & PARODD) ? 0x10 : 0x20; - - /* set the number of data bits */ - switch (cflag & CSIZE) { - case CS5: - val |= 5 << 8; break; - case CS6: - val |= 6 << 8; break; - case CS7: - val |= 7 << 8; break; - case CS8: - val |= 8 << 8; break; - default: - dev_err(cs->dev, "CSIZE was not CS5-CS8, using default of 8\n"); - val |= 8 << 8; - break; - } - - /* set the number of stop bits */ - if (cflag & CSTOPB) { - if ((cflag & CSIZE) == CS5) - val |= 1; /* 1.5 stop bits */ - else - val |= 2; /* 2 stop bits */ - } - - return set_value(cs, 3, val); -} - - -/*============================================================================*/ -static int gigaset_init_bchannel(struct bc_state *bcs) -{ - /* nothing to do for M10x */ - gigaset_bchannel_up(bcs); - return 0; -} - -static int gigaset_close_bchannel(struct bc_state *bcs) -{ - /* nothing to do for M10x */ - gigaset_bchannel_down(bcs); - return 0; -} - -static int write_modem(struct cardstate *cs); -static int send_cb(struct cardstate *cs); - - -/* Write tasklet handler: Continue sending current skb, or send command, or - * start sending an skb from the send queue. - */ -static void gigaset_modem_fill(unsigned long data) -{ - struct cardstate *cs = (struct cardstate *) data; - struct bc_state *bcs = &cs->bcs[0]; /* only one channel */ - - gig_dbg(DEBUG_OUTPUT, "modem_fill"); - - if (cs->hw.usb->busy) { - gig_dbg(DEBUG_OUTPUT, "modem_fill: busy"); - return; - } - -again: - if (!bcs->tx_skb) { /* no skb is being sent */ - if (cs->cmdbuf) { /* commands to send? */ - gig_dbg(DEBUG_OUTPUT, "modem_fill: cb"); - if (send_cb(cs) < 0) { - gig_dbg(DEBUG_OUTPUT, - "modem_fill: send_cb failed"); - goto again; /* no callback will be called! */ - } - return; - } - - /* skbs to send? */ - bcs->tx_skb = skb_dequeue(&bcs->squeue); - if (!bcs->tx_skb) - return; - - gig_dbg(DEBUG_INTR, "Dequeued skb (Adr: %lx)!", - (unsigned long) bcs->tx_skb); - } - - gig_dbg(DEBUG_OUTPUT, "modem_fill: tx_skb"); - if (write_modem(cs) < 0) { - gig_dbg(DEBUG_OUTPUT, "modem_fill: write_modem failed"); - goto again; /* no callback will be called! */ - } -} - -/* - * Interrupt Input URB completion routine - */ -static void gigaset_read_int_callback(struct urb *urb) -{ - struct cardstate *cs = urb->context; - struct inbuf_t *inbuf = cs->inbuf; - int status = urb->status; - int r; - unsigned numbytes; - unsigned char *src; - unsigned long flags; - - if (!status) { - numbytes = urb->actual_length; - - if (numbytes) { - src = cs->hw.usb->rcvbuf; - if (unlikely(*src)) - dev_warn(cs->dev, - "%s: There was no leading 0, but 0x%02x!\n", - __func__, (unsigned) *src); - ++src; /* skip leading 0x00 */ - --numbytes; - if (gigaset_fill_inbuf(inbuf, src, numbytes)) { - gig_dbg(DEBUG_INTR, "%s-->BH", __func__); - gigaset_schedule_event(inbuf->cs); - } - } else - gig_dbg(DEBUG_INTR, "Received zero block length"); - } else { - /* The urb might have been killed. */ - gig_dbg(DEBUG_ANY, "%s - nonzero status received: %d", - __func__, status); - if (status == -ENOENT || status == -ESHUTDOWN) - /* killed or endpoint shutdown: don't resubmit */ - return; - } - - /* resubmit URB */ - spin_lock_irqsave(&cs->lock, flags); - if (!cs->connected) { - spin_unlock_irqrestore(&cs->lock, flags); - pr_err("%s: disconnected\n", __func__); - return; - } - r = usb_submit_urb(urb, GFP_ATOMIC); - spin_unlock_irqrestore(&cs->lock, flags); - if (r) - dev_err(cs->dev, "error %d resubmitting URB\n", -r); -} - - -/* This callback routine is called when data was transmitted to the device. */ -static void gigaset_write_bulk_callback(struct urb *urb) -{ - struct cardstate *cs = urb->context; - int status = urb->status; - unsigned long flags; - - switch (status) { - case 0: /* normal completion */ - break; - case -ENOENT: /* killed */ - gig_dbg(DEBUG_ANY, "%s: killed", __func__); - cs->hw.usb->busy = 0; - return; - default: - dev_err(cs->dev, "bulk transfer failed (status %d)\n", - -status); - /* That's all we can do. Communication problems - are handled by timeouts or network protocols. */ - } - - spin_lock_irqsave(&cs->lock, flags); - if (!cs->connected) { - pr_err("%s: disconnected\n", __func__); - } else { - cs->hw.usb->busy = 0; - tasklet_schedule(&cs->write_tasklet); - } - spin_unlock_irqrestore(&cs->lock, flags); -} - -static int send_cb(struct cardstate *cs) -{ - struct cmdbuf_t *cb = cs->cmdbuf; - unsigned long flags; - int count; - int status = -ENOENT; - struct usb_cardstate *ucs = cs->hw.usb; - - do { - if (!cb->len) { - spin_lock_irqsave(&cs->cmdlock, flags); - cs->cmdbytes -= cs->curlen; - gig_dbg(DEBUG_OUTPUT, "send_cb: sent %u bytes, %u left", - cs->curlen, cs->cmdbytes); - cs->cmdbuf = cb->next; - if (cs->cmdbuf) { - cs->cmdbuf->prev = NULL; - cs->curlen = cs->cmdbuf->len; - } else { - cs->lastcmdbuf = NULL; - cs->curlen = 0; - } - spin_unlock_irqrestore(&cs->cmdlock, flags); - - if (cb->wake_tasklet) - tasklet_schedule(cb->wake_tasklet); - kfree(cb); - - cb = cs->cmdbuf; - } - - if (cb) { - count = min(cb->len, ucs->bulk_out_size); - gig_dbg(DEBUG_OUTPUT, "send_cb: send %d bytes", count); - - usb_fill_bulk_urb(ucs->bulk_out_urb, ucs->udev, - usb_sndbulkpipe(ucs->udev, - ucs->bulk_out_epnum), - cb->buf + cb->offset, count, - gigaset_write_bulk_callback, cs); - - cb->offset += count; - cb->len -= count; - ucs->busy = 1; - - spin_lock_irqsave(&cs->lock, flags); - status = cs->connected ? - usb_submit_urb(ucs->bulk_out_urb, GFP_ATOMIC) : - -ENODEV; - spin_unlock_irqrestore(&cs->lock, flags); - - if (status) { - ucs->busy = 0; - dev_err(cs->dev, - "could not submit urb (error %d)\n", - -status); - cb->len = 0; /* skip urb => remove cb+wakeup - in next loop cycle */ - } - } - } while (cb && status); /* next command on error */ - - return status; -} - -/* Send command to device. */ -static int gigaset_write_cmd(struct cardstate *cs, struct cmdbuf_t *cb) -{ - unsigned long flags; - int len; - - gigaset_dbg_buffer(cs->mstate != MS_LOCKED ? - DEBUG_TRANSCMD : DEBUG_LOCKCMD, - "CMD Transmit", cb->len, cb->buf); - - spin_lock_irqsave(&cs->cmdlock, flags); - cb->prev = cs->lastcmdbuf; - if (cs->lastcmdbuf) - cs->lastcmdbuf->next = cb; - else { - cs->cmdbuf = cb; - cs->curlen = cb->len; - } - cs->cmdbytes += cb->len; - cs->lastcmdbuf = cb; - spin_unlock_irqrestore(&cs->cmdlock, flags); - - spin_lock_irqsave(&cs->lock, flags); - len = cb->len; - if (cs->connected) - tasklet_schedule(&cs->write_tasklet); - spin_unlock_irqrestore(&cs->lock, flags); - return len; -} - -static int gigaset_write_room(struct cardstate *cs) -{ - unsigned bytes; - - bytes = cs->cmdbytes; - return bytes < IF_WRITEBUF ? IF_WRITEBUF - bytes : 0; -} - -static int gigaset_chars_in_buffer(struct cardstate *cs) -{ - return cs->cmdbytes; -} - -/* - * set the break characters on the internal serial adapter - * using undocumented device commands reverse engineered from USB traces - * of the Siemens Windows driver - */ -static int gigaset_brkchars(struct cardstate *cs, const unsigned char buf[6]) -{ - struct usb_device *udev = cs->hw.usb->udev; - - gigaset_dbg_buffer(DEBUG_USBREQ, "brkchars", 6, buf); - memcpy(cs->hw.usb->bchars, buf, 6); - return usb_control_msg(udev, usb_sndctrlpipe(udev, 0), 0x19, 0x41, - 0, 0, &buf, 6, 2000); -} - -static void gigaset_freebcshw(struct bc_state *bcs) -{ - /* unused */ -} - -/* Initialize the b-channel structure */ -static int gigaset_initbcshw(struct bc_state *bcs) -{ - /* unused */ - bcs->hw.usb = NULL; - return 0; -} - -static void gigaset_reinitbcshw(struct bc_state *bcs) -{ - /* nothing to do for M10x */ -} - -static void gigaset_freecshw(struct cardstate *cs) -{ - tasklet_kill(&cs->write_tasklet); - kfree(cs->hw.usb); -} - -static int gigaset_initcshw(struct cardstate *cs) -{ - struct usb_cardstate *ucs; - - cs->hw.usb = ucs = kzalloc(sizeof(struct usb_cardstate), GFP_KERNEL); - if (!ucs) { - pr_err("out of memory\n"); - return -ENOMEM; - } - - ucs->bchars[0] = 0; - ucs->bchars[1] = 0; - ucs->bchars[2] = 0; - ucs->bchars[3] = 0; - ucs->bchars[4] = 0x11; - ucs->bchars[5] = 0x13; - tasklet_init(&cs->write_tasklet, - gigaset_modem_fill, (unsigned long) cs); - - return 0; -} - -/* Send data from current skb to the device. */ -static int write_modem(struct cardstate *cs) -{ - int ret = 0; - int count; - struct bc_state *bcs = &cs->bcs[0]; /* only one channel */ - struct usb_cardstate *ucs = cs->hw.usb; - unsigned long flags; - - gig_dbg(DEBUG_OUTPUT, "len: %d...", bcs->tx_skb->len); - - if (!bcs->tx_skb->len) { - dev_kfree_skb_any(bcs->tx_skb); - bcs->tx_skb = NULL; - return -EINVAL; - } - - /* Copy data to bulk out buffer and transmit data */ - count = min(bcs->tx_skb->len, (unsigned) ucs->bulk_out_size); - skb_copy_from_linear_data(bcs->tx_skb, ucs->bulk_out_buffer, count); - skb_pull(bcs->tx_skb, count); - ucs->busy = 1; - gig_dbg(DEBUG_OUTPUT, "write_modem: send %d bytes", count); - - spin_lock_irqsave(&cs->lock, flags); - if (cs->connected) { - usb_fill_bulk_urb(ucs->bulk_out_urb, ucs->udev, - usb_sndbulkpipe(ucs->udev, - ucs->bulk_out_epnum), - ucs->bulk_out_buffer, count, - gigaset_write_bulk_callback, cs); - ret = usb_submit_urb(ucs->bulk_out_urb, GFP_ATOMIC); - } else { - ret = -ENODEV; - } - spin_unlock_irqrestore(&cs->lock, flags); - - if (ret) { - dev_err(cs->dev, "could not submit urb (error %d)\n", -ret); - ucs->busy = 0; - } - - if (!bcs->tx_skb->len) { - /* skb sent completely */ - gigaset_skb_sent(bcs, bcs->tx_skb); - - gig_dbg(DEBUG_INTR, "kfree skb (Adr: %lx)!", - (unsigned long) bcs->tx_skb); - dev_kfree_skb_any(bcs->tx_skb); - bcs->tx_skb = NULL; - } - - return ret; -} - -static int gigaset_probe(struct usb_interface *interface, - const struct usb_device_id *id) -{ - int retval; - struct usb_device *udev = interface_to_usbdev(interface); - struct usb_host_interface *hostif = interface->cur_altsetting; - struct cardstate *cs = NULL; - struct usb_cardstate *ucs = NULL; - struct usb_endpoint_descriptor *endpoint; - int buffer_size; - - gig_dbg(DEBUG_ANY, "%s: Check if device matches ...", __func__); - - /* See if the device offered us matches what we can accept */ - if ((le16_to_cpu(udev->descriptor.idVendor) != USB_M105_VENDOR_ID) || - (le16_to_cpu(udev->descriptor.idProduct) != USB_M105_PRODUCT_ID)) { - gig_dbg(DEBUG_ANY, "device ID (0x%x, 0x%x) not for me - skip", - le16_to_cpu(udev->descriptor.idVendor), - le16_to_cpu(udev->descriptor.idProduct)); - return -ENODEV; - } - if (hostif->desc.bInterfaceNumber != 0) { - gig_dbg(DEBUG_ANY, "interface %d not for me - skip", - hostif->desc.bInterfaceNumber); - return -ENODEV; - } - if (hostif->desc.bAlternateSetting != 0) { - dev_notice(&udev->dev, "unsupported altsetting %d - skip", - hostif->desc.bAlternateSetting); - return -ENODEV; - } - if (hostif->desc.bInterfaceClass != 255) { - dev_notice(&udev->dev, "unsupported interface class %d - skip", - hostif->desc.bInterfaceClass); - return -ENODEV; - } - - if (hostif->desc.bNumEndpoints < 2) { - dev_err(&interface->dev, "missing endpoints\n"); - return -ENODEV; - } - - dev_info(&udev->dev, "%s: Device matched ... !\n", __func__); - - /* allocate memory for our device state and initialize it */ - cs = gigaset_initcs(driver, 1, 1, 0, cidmode, GIGASET_MODULENAME); - if (!cs) - return -ENODEV; - ucs = cs->hw.usb; - - /* save off device structure ptrs for later use */ - usb_get_dev(udev); - ucs->udev = udev; - ucs->interface = interface; - cs->dev = &interface->dev; - - /* save address of controller structure */ - usb_set_intfdata(interface, cs); - - endpoint = &hostif->endpoint[0].desc; - - if (!usb_endpoint_is_bulk_out(endpoint)) { - dev_err(&interface->dev, "missing bulk-out endpoint\n"); - retval = -ENODEV; - goto error; - } - - buffer_size = le16_to_cpu(endpoint->wMaxPacketSize); - ucs->bulk_out_size = buffer_size; - ucs->bulk_out_epnum = usb_endpoint_num(endpoint); - ucs->bulk_out_buffer = kmalloc(buffer_size, GFP_KERNEL); - if (!ucs->bulk_out_buffer) { - dev_err(cs->dev, "Couldn't allocate bulk_out_buffer\n"); - retval = -ENOMEM; - goto error; - } - - ucs->bulk_out_urb = usb_alloc_urb(0, GFP_KERNEL); - if (!ucs->bulk_out_urb) { - dev_err(cs->dev, "Couldn't allocate bulk_out_urb\n"); - retval = -ENOMEM; - goto error; - } - - endpoint = &hostif->endpoint[1].desc; - - if (!usb_endpoint_is_int_in(endpoint)) { - dev_err(&interface->dev, "missing int-in endpoint\n"); - retval = -ENODEV; - goto error; - } - - ucs->busy = 0; - - ucs->read_urb = usb_alloc_urb(0, GFP_KERNEL); - if (!ucs->read_urb) { - dev_err(cs->dev, "No free urbs available\n"); - retval = -ENOMEM; - goto error; - } - buffer_size = le16_to_cpu(endpoint->wMaxPacketSize); - ucs->rcvbuf_size = buffer_size; - ucs->rcvbuf = kmalloc(buffer_size, GFP_KERNEL); - if (!ucs->rcvbuf) { - dev_err(cs->dev, "Couldn't allocate rcvbuf\n"); - retval = -ENOMEM; - goto error; - } - /* Fill the interrupt urb and send it to the core */ - usb_fill_int_urb(ucs->read_urb, udev, - usb_rcvintpipe(udev, usb_endpoint_num(endpoint)), - ucs->rcvbuf, buffer_size, - gigaset_read_int_callback, - cs, endpoint->bInterval); - - retval = usb_submit_urb(ucs->read_urb, GFP_KERNEL); - if (retval) { - dev_err(cs->dev, "Could not submit URB (error %d)\n", -retval); - goto error; - } - - /* tell common part that the device is ready */ - if (startmode == SM_LOCKED) - cs->mstate = MS_LOCKED; - - retval = gigaset_start(cs); - if (retval < 0) { - tasklet_kill(&cs->write_tasklet); - goto error; - } - return 0; - -error: - usb_kill_urb(ucs->read_urb); - kfree(ucs->bulk_out_buffer); - usb_free_urb(ucs->bulk_out_urb); - kfree(ucs->rcvbuf); - usb_free_urb(ucs->read_urb); - usb_set_intfdata(interface, NULL); - ucs->read_urb = ucs->bulk_out_urb = NULL; - ucs->rcvbuf = ucs->bulk_out_buffer = NULL; - usb_put_dev(ucs->udev); - ucs->udev = NULL; - ucs->interface = NULL; - gigaset_freecs(cs); - return retval; -} - -static void gigaset_disconnect(struct usb_interface *interface) -{ - struct cardstate *cs; - struct usb_cardstate *ucs; - - cs = usb_get_intfdata(interface); - ucs = cs->hw.usb; - - dev_info(cs->dev, "disconnecting Gigaset USB adapter\n"); - - usb_kill_urb(ucs->read_urb); - - gigaset_stop(cs); - - usb_set_intfdata(interface, NULL); - tasklet_kill(&cs->write_tasklet); - - usb_kill_urb(ucs->bulk_out_urb); - - kfree(ucs->bulk_out_buffer); - usb_free_urb(ucs->bulk_out_urb); - kfree(ucs->rcvbuf); - usb_free_urb(ucs->read_urb); - ucs->read_urb = ucs->bulk_out_urb = NULL; - ucs->rcvbuf = ucs->bulk_out_buffer = NULL; - - usb_put_dev(ucs->udev); - ucs->interface = NULL; - ucs->udev = NULL; - cs->dev = NULL; - gigaset_freecs(cs); -} - -/* gigaset_suspend - * This function is called before the USB connection is suspended or reset. - */ -static int gigaset_suspend(struct usb_interface *intf, pm_message_t message) -{ - struct cardstate *cs = usb_get_intfdata(intf); - - /* stop activity */ - cs->connected = 0; /* prevent rescheduling */ - usb_kill_urb(cs->hw.usb->read_urb); - tasklet_kill(&cs->write_tasklet); - usb_kill_urb(cs->hw.usb->bulk_out_urb); - - gig_dbg(DEBUG_SUSPEND, "suspend complete"); - return 0; -} - -/* gigaset_resume - * This function is called after the USB connection has been resumed or reset. - */ -static int gigaset_resume(struct usb_interface *intf) -{ - struct cardstate *cs = usb_get_intfdata(intf); - int rc; - - /* resubmit interrupt URB */ - cs->connected = 1; - rc = usb_submit_urb(cs->hw.usb->read_urb, GFP_KERNEL); - if (rc) { - dev_err(cs->dev, "Could not submit read URB (error %d)\n", -rc); - return rc; - } - - gig_dbg(DEBUG_SUSPEND, "resume complete"); - return 0; -} - -/* gigaset_pre_reset - * This function is called before the USB connection is reset. - */ -static int gigaset_pre_reset(struct usb_interface *intf) -{ - /* same as suspend */ - return gigaset_suspend(intf, PMSG_ON); -} - -static const struct gigaset_ops ops = { - .write_cmd = gigaset_write_cmd, - .write_room = gigaset_write_room, - .chars_in_buffer = gigaset_chars_in_buffer, - .brkchars = gigaset_brkchars, - .init_bchannel = gigaset_init_bchannel, - .close_bchannel = gigaset_close_bchannel, - .initbcshw = gigaset_initbcshw, - .freebcshw = gigaset_freebcshw, - .reinitbcshw = gigaset_reinitbcshw, - .initcshw = gigaset_initcshw, - .freecshw = gigaset_freecshw, - .set_modem_ctrl = gigaset_set_modem_ctrl, - .baud_rate = gigaset_baud_rate, - .set_line_ctrl = gigaset_set_line_ctrl, - .send_skb = gigaset_m10x_send_skb, - .handle_input = gigaset_m10x_input, -}; - -/* - * This function is called while kernel-module is loaded - */ -static int __init usb_gigaset_init(void) -{ - int result; - - /* allocate memory for our driver state and initialize it */ - driver = gigaset_initdriver(GIGASET_MINOR, GIGASET_MINORS, - GIGASET_MODULENAME, GIGASET_DEVNAME, - &ops, THIS_MODULE); - if (driver == NULL) { - result = -ENOMEM; - goto error; - } - - /* register this driver with the USB subsystem */ - result = usb_register(&gigaset_usb_driver); - if (result < 0) { - pr_err("error %d registering USB driver\n", -result); - goto error; - } - - pr_info(DRIVER_DESC "\n"); - return 0; - -error: - if (driver) - gigaset_freedriver(driver); - driver = NULL; - return result; -} - -/* - * This function is called while unloading the kernel-module - */ -static void __exit usb_gigaset_exit(void) -{ - int i; - - gigaset_blockdriver(driver); /* => probe will fail - * => no gigaset_start any more - */ - - /* stop all connected devices */ - for (i = 0; i < driver->minors; i++) - gigaset_shutdown(driver->cs + i); - - /* from now on, no isdn callback should be possible */ - - /* deregister this driver with the USB subsystem */ - usb_deregister(&gigaset_usb_driver); - /* this will call the disconnect-callback */ - /* from now on, no disconnect/probe callback should be running */ - - gigaset_freedriver(driver); - driver = NULL; -} - - -module_init(usb_gigaset_init); -module_exit(usb_gigaset_exit); - -MODULE_AUTHOR(DRIVER_AUTHOR); -MODULE_DESCRIPTION(DRIVER_DESC); - -MODULE_LICENSE("GPL"); diff --git a/drivers/staging/isdn/hysdn/Kconfig b/drivers/staging/isdn/hysdn/Kconfig deleted file mode 100644 index 4c8a9283b9dd..000000000000 --- a/drivers/staging/isdn/hysdn/Kconfig +++ /dev/null @@ -1,15 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0-only -config HYSDN - tristate "Hypercope HYSDN cards (Champ, Ergo, Metro) support (module only)" - depends on m && PROC_FS && PCI - help - Say Y here if you have one of Hypercope's active PCI ISDN cards - Champ, Ergo and Metro. You will then get a module called hysdn. - Please read the file <file:Documentation/isdn/hysdn.rst> for more - information. - -config HYSDN_CAPI - bool "HYSDN CAPI 2.0 support" - depends on HYSDN && ISDN_CAPI - help - Say Y here if you like to use Hypercope's CAPI 2.0 interface. diff --git a/drivers/staging/isdn/hysdn/Makefile b/drivers/staging/isdn/hysdn/Makefile deleted file mode 100644 index e01f17f22ebb..000000000000 --- a/drivers/staging/isdn/hysdn/Makefile +++ /dev/null @@ -1,12 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0-only -# Makefile for the hysdn ISDN device driver - -# Each configuration option enables a list of files. - -obj-$(CONFIG_HYSDN) += hysdn.o - -# Multipart objects. - -hysdn-y := hysdn_procconf.o hysdn_proclog.o boardergo.o \ - hysdn_boot.o hysdn_sched.o hysdn_net.o hysdn_init.o -hysdn-$(CONFIG_HYSDN_CAPI) += hycapi.o diff --git a/drivers/staging/isdn/hysdn/boardergo.c b/drivers/staging/isdn/hysdn/boardergo.c deleted file mode 100644 index 2aa2a0e08247..000000000000 --- a/drivers/staging/isdn/hysdn/boardergo.c +++ /dev/null @@ -1,445 +0,0 @@ -/* $Id: boardergo.c,v 1.5.6.7 2001/11/06 21:58:19 kai Exp $ - * - * Linux driver for HYSDN cards, specific routines for ergo type boards. - * - * Author Werner Cornelius (werner@titro.de) for Hypercope GmbH - * Copyright 1999 by Werner Cornelius (werner@titro.de) - * - * This software may be used and distributed according to the terms - * of the GNU General Public License, incorporated herein by reference. - * - * As all Linux supported cards Champ2, Ergo and Metro2/4 use the same - * DPRAM interface and layout with only minor differences all related - * stuff is done here, not in separate modules. - * - */ - -#include <linux/signal.h> -#include <linux/kernel.h> -#include <linux/ioport.h> -#include <linux/interrupt.h> -#include <linux/vmalloc.h> -#include <linux/delay.h> -#include <asm/io.h> - -#include "hysdn_defs.h" -#include "boardergo.h" - -#define byteout(addr, val) outb(val, addr) -#define bytein(addr) inb(addr) - -/***************************************************/ -/* The cards interrupt handler. Called from system */ -/***************************************************/ -static irqreturn_t -ergo_interrupt(int intno, void *dev_id) -{ - hysdn_card *card = dev_id; /* parameter from irq */ - tErgDpram *dpr; - unsigned long flags; - unsigned char volatile b; - - if (!card) - return IRQ_NONE; /* error -> spurious interrupt */ - if (!card->irq_enabled) - return IRQ_NONE; /* other device interrupting or irq switched off */ - - spin_lock_irqsave(&card->hysdn_lock, flags); /* no further irqs allowed */ - - if (!(bytein(card->iobase + PCI9050_INTR_REG) & PCI9050_INTR_REG_STAT1)) { - spin_unlock_irqrestore(&card->hysdn_lock, flags); /* restore old state */ - return IRQ_NONE; /* no interrupt requested by E1 */ - } - /* clear any pending ints on the board */ - dpr = card->dpram; - b = dpr->ToPcInt; /* clear for ergo */ - b |= dpr->ToPcIntMetro; /* same for metro */ - b |= dpr->ToHyInt; /* and for champ */ - - /* start kernel task immediately after leaving all interrupts */ - if (!card->hw_lock) - schedule_work(&card->irq_queue); - spin_unlock_irqrestore(&card->hysdn_lock, flags); - return IRQ_HANDLED; -} /* ergo_interrupt */ - -/******************************************************************************/ -/* ergo_irq_bh will be called as part of the kernel clearing its shared work */ -/* queue sometime after a call to schedule_work has been made passing our */ -/* work_struct. This task is the only one handling data transfer from or to */ -/* the card after booting. The task may be queued from everywhere */ -/* (interrupts included). */ -/******************************************************************************/ -static void -ergo_irq_bh(struct work_struct *ugli_api) -{ - hysdn_card *card = container_of(ugli_api, hysdn_card, irq_queue); - tErgDpram *dpr; - int again; - unsigned long flags; - - if (card->state != CARD_STATE_RUN) - return; /* invalid call */ - - dpr = card->dpram; /* point to DPRAM */ - - spin_lock_irqsave(&card->hysdn_lock, flags); - if (card->hw_lock) { - spin_unlock_irqrestore(&card->hysdn_lock, flags); /* hardware currently unavailable */ - return; - } - card->hw_lock = 1; /* we now lock the hardware */ - - do { - again = 0; /* assume loop not to be repeated */ - - if (!dpr->ToHyFlag) { - /* we are able to send a buffer */ - - if (hysdn_sched_tx(card, dpr->ToHyBuf, &dpr->ToHySize, &dpr->ToHyChannel, - ERG_TO_HY_BUF_SIZE)) { - dpr->ToHyFlag = 1; /* enable tx */ - again = 1; /* restart loop */ - } - } /* we are able to send a buffer */ - if (dpr->ToPcFlag) { - /* a message has arrived for us, handle it */ - - if (hysdn_sched_rx(card, dpr->ToPcBuf, dpr->ToPcSize, dpr->ToPcChannel)) { - dpr->ToPcFlag = 0; /* we worked the data */ - again = 1; /* restart loop */ - } - } /* a message has arrived for us */ - if (again) { - dpr->ToHyInt = 1; - dpr->ToPcInt = 1; /* interrupt to E1 for all cards */ - } else - card->hw_lock = 0; /* free hardware again */ - } while (again); /* until nothing more to do */ - - spin_unlock_irqrestore(&card->hysdn_lock, flags); -} /* ergo_irq_bh */ - - -/*********************************************************/ -/* stop the card (hardware reset) and disable interrupts */ -/*********************************************************/ -static void -ergo_stopcard(hysdn_card *card) -{ - unsigned long flags; - unsigned char val; - - hysdn_net_release(card); /* first release the net device if existing */ -#ifdef CONFIG_HYSDN_CAPI - hycapi_capi_stop(card); -#endif /* CONFIG_HYSDN_CAPI */ - spin_lock_irqsave(&card->hysdn_lock, flags); - val = bytein(card->iobase + PCI9050_INTR_REG); /* get actual value */ - val &= ~(PCI9050_INTR_REG_ENPCI | PCI9050_INTR_REG_EN1); /* mask irq */ - byteout(card->iobase + PCI9050_INTR_REG, val); - card->irq_enabled = 0; - byteout(card->iobase + PCI9050_USER_IO, PCI9050_E1_RESET); /* reset E1 processor */ - card->state = CARD_STATE_UNUSED; - card->err_log_state = ERRLOG_STATE_OFF; /* currently no log active */ - - spin_unlock_irqrestore(&card->hysdn_lock, flags); -} /* ergo_stopcard */ - -/**************************************************************************/ -/* enable or disable the cards error log. The event is queued if possible */ -/**************************************************************************/ -static void -ergo_set_errlog_state(hysdn_card *card, int on) -{ - unsigned long flags; - - if (card->state != CARD_STATE_RUN) { - card->err_log_state = ERRLOG_STATE_OFF; /* must be off */ - return; - } - spin_lock_irqsave(&card->hysdn_lock, flags); - - if (((card->err_log_state == ERRLOG_STATE_OFF) && !on) || - ((card->err_log_state == ERRLOG_STATE_ON) && on)) { - spin_unlock_irqrestore(&card->hysdn_lock, flags); - return; /* nothing to do */ - } - if (on) - card->err_log_state = ERRLOG_STATE_START; /* request start */ - else - card->err_log_state = ERRLOG_STATE_STOP; /* request stop */ - - spin_unlock_irqrestore(&card->hysdn_lock, flags); - schedule_work(&card->irq_queue); -} /* ergo_set_errlog_state */ - -/******************************************/ -/* test the cards RAM and return 0 if ok. */ -/******************************************/ -static const char TestText[36] = "This Message is filler, why read it"; - -static int -ergo_testram(hysdn_card *card) -{ - tErgDpram *dpr = card->dpram; - - memset(dpr->TrapTable, 0, sizeof(dpr->TrapTable)); /* clear all Traps */ - dpr->ToHyInt = 1; /* E1 INTR state forced */ - - memcpy(&dpr->ToHyBuf[ERG_TO_HY_BUF_SIZE - sizeof(TestText)], TestText, - sizeof(TestText)); - if (memcmp(&dpr->ToHyBuf[ERG_TO_HY_BUF_SIZE - sizeof(TestText)], TestText, - sizeof(TestText))) - return (-1); - - memcpy(&dpr->ToPcBuf[ERG_TO_PC_BUF_SIZE - sizeof(TestText)], TestText, - sizeof(TestText)); - if (memcmp(&dpr->ToPcBuf[ERG_TO_PC_BUF_SIZE - sizeof(TestText)], TestText, - sizeof(TestText))) - return (-1); - - return (0); -} /* ergo_testram */ - -/*****************************************************************************/ -/* this function is intended to write stage 1 boot image to the cards buffer */ -/* this is done in two steps. First the 1024 hi-words are written (offs=0), */ -/* then the 1024 lo-bytes are written. The remaining DPRAM is cleared, the */ -/* PCI-write-buffers flushed and the card is taken out of reset. */ -/* The function then waits for a reaction of the E1 processor or a timeout. */ -/* Negative return values are interpreted as errors. */ -/*****************************************************************************/ -static int -ergo_writebootimg(struct HYSDN_CARD *card, unsigned char *buf, - unsigned long offs) -{ - unsigned char *dst; - tErgDpram *dpram; - int cnt = (BOOT_IMG_SIZE >> 2); /* number of words to move and swap (byte order!) */ - - if (card->debug_flags & LOG_POF_CARD) - hysdn_addlog(card, "ERGO: write bootldr offs=0x%lx ", offs); - - dst = card->dpram; /* pointer to start of DPRAM */ - dst += (offs + ERG_DPRAM_FILL_SIZE); /* offset in the DPRAM */ - while (cnt--) { - *dst++ = *(buf + 1); /* high byte */ - *dst++ = *buf; /* low byte */ - dst += 2; /* point to next longword */ - buf += 2; /* buffer only filled with words */ - } - - /* if low words (offs = 2) have been written, clear the rest of the DPRAM, */ - /* flush the PCI-write-buffer and take the E1 out of reset */ - if (offs) { - memset(card->dpram, 0, ERG_DPRAM_FILL_SIZE); /* fill the DPRAM still not cleared */ - dpram = card->dpram; /* get pointer to dpram structure */ - dpram->ToHyNoDpramErrLog = 0xFF; /* write a dpram register */ - while (!dpram->ToHyNoDpramErrLog); /* reread volatile register to flush PCI */ - - byteout(card->iobase + PCI9050_USER_IO, PCI9050_E1_RUN); /* start E1 processor */ - /* the interrupts are still masked */ - - msleep_interruptible(20); /* Timeout 20ms */ - - if (((tDpramBootSpooler *) card->dpram)->Len != DPRAM_SPOOLER_DATA_SIZE) { - if (card->debug_flags & LOG_POF_CARD) - hysdn_addlog(card, "ERGO: write bootldr no answer"); - return (-ERR_BOOTIMG_FAIL); - } - } /* start_boot_img */ - return (0); /* successful */ -} /* ergo_writebootimg */ - -/********************************************************************************/ -/* ergo_writebootseq writes the buffer containing len bytes to the E1 processor */ -/* using the boot spool mechanism. If everything works fine 0 is returned. In */ -/* case of errors a negative error value is returned. */ -/********************************************************************************/ -static int -ergo_writebootseq(struct HYSDN_CARD *card, unsigned char *buf, int len) -{ - tDpramBootSpooler *sp = (tDpramBootSpooler *) card->dpram; - unsigned char *dst; - unsigned char buflen; - int nr_write; - unsigned char tmp_rdptr; - unsigned char wr_mirror; - int i; - - if (card->debug_flags & LOG_POF_CARD) - hysdn_addlog(card, "ERGO: write boot seq len=%d ", len); - - dst = sp->Data; /* point to data in spool structure */ - buflen = sp->Len; /* maximum len of spooled data */ - wr_mirror = sp->WrPtr; /* only once read */ - - /* try until all bytes written or error */ - i = 0x1000; /* timeout value */ - while (len) { - - /* first determine the number of bytes that may be buffered */ - do { - tmp_rdptr = sp->RdPtr; /* first read the pointer */ - i--; /* decrement timeout */ - } while (i && (tmp_rdptr != sp->RdPtr)); /* wait for stable pointer */ - - if (!i) { - if (card->debug_flags & LOG_POF_CARD) - hysdn_addlog(card, "ERGO: write boot seq timeout"); - return (-ERR_BOOTSEQ_FAIL); /* value not stable -> timeout */ - } - if ((nr_write = tmp_rdptr - wr_mirror - 1) < 0) - nr_write += buflen; /* now we got number of free bytes - 1 in buffer */ - - if (!nr_write) - continue; /* no free bytes in buffer */ - - if (nr_write > len) - nr_write = len; /* limit if last few bytes */ - i = 0x1000; /* reset timeout value */ - - /* now we know how much bytes we may put in the puffer */ - len -= nr_write; /* we savely could adjust len before output */ - while (nr_write--) { - *(dst + wr_mirror) = *buf++; /* output one byte */ - if (++wr_mirror >= buflen) - wr_mirror = 0; - sp->WrPtr = wr_mirror; /* announce the next byte to E1 */ - } /* while (nr_write) */ - - } /* while (len) */ - return (0); -} /* ergo_writebootseq */ - -/***********************************************************************************/ -/* ergo_waitpofready waits for a maximum of 10 seconds for the completition of the */ -/* boot process. If the process has been successful 0 is returned otherwise a */ -/* negative error code is returned. */ -/***********************************************************************************/ -static int -ergo_waitpofready(struct HYSDN_CARD *card) -{ - tErgDpram *dpr = card->dpram; /* pointer to DPRAM structure */ - int timecnt = 10000 / 50; /* timeout is 10 secs max. */ - unsigned long flags; - int msg_size; - int i; - - if (card->debug_flags & LOG_POF_CARD) - hysdn_addlog(card, "ERGO: waiting for pof ready"); - while (timecnt--) { - /* wait until timeout */ - - if (dpr->ToPcFlag) { - /* data has arrived */ - - if ((dpr->ToPcChannel != CHAN_SYSTEM) || - (dpr->ToPcSize < MIN_RDY_MSG_SIZE) || - (dpr->ToPcSize > MAX_RDY_MSG_SIZE) || - ((*(unsigned long *) dpr->ToPcBuf) != RDY_MAGIC)) - break; /* an error occurred */ - - /* Check for additional data delivered during SysReady */ - msg_size = dpr->ToPcSize - RDY_MAGIC_SIZE; - if (msg_size > 0) - if (EvalSysrTokData(card, dpr->ToPcBuf + RDY_MAGIC_SIZE, msg_size)) - break; - - if (card->debug_flags & LOG_POF_RECORD) - hysdn_addlog(card, "ERGO: pof boot success"); - spin_lock_irqsave(&card->hysdn_lock, flags); - - card->state = CARD_STATE_RUN; /* now card is running */ - /* enable the cards interrupt */ - byteout(card->iobase + PCI9050_INTR_REG, - bytein(card->iobase + PCI9050_INTR_REG) | - (PCI9050_INTR_REG_ENPCI | PCI9050_INTR_REG_EN1)); - card->irq_enabled = 1; /* we are ready to receive interrupts */ - - dpr->ToPcFlag = 0; /* reset data indicator */ - dpr->ToHyInt = 1; - dpr->ToPcInt = 1; /* interrupt to E1 for all cards */ - - spin_unlock_irqrestore(&card->hysdn_lock, flags); - if ((hynet_enable & (1 << card->myid)) - && (i = hysdn_net_create(card))) - { - ergo_stopcard(card); - card->state = CARD_STATE_BOOTERR; - return (i); - } -#ifdef CONFIG_HYSDN_CAPI - if ((i = hycapi_capi_create(card))) { - printk(KERN_WARNING "HYSDN: failed to create capi-interface.\n"); - } -#endif /* CONFIG_HYSDN_CAPI */ - return (0); /* success */ - } /* data has arrived */ - msleep_interruptible(50); /* Timeout 50ms */ - } /* wait until timeout */ - - if (card->debug_flags & LOG_POF_CARD) - hysdn_addlog(card, "ERGO: pof boot ready timeout"); - return (-ERR_POF_TIMEOUT); -} /* ergo_waitpofready */ - - - -/************************************************************************************/ -/* release the cards hardware. Before releasing do a interrupt disable and hardware */ -/* reset. Also unmap dpram. */ -/* Use only during module release. */ -/************************************************************************************/ -static void -ergo_releasehardware(hysdn_card *card) -{ - ergo_stopcard(card); /* first stop the card if not already done */ - free_irq(card->irq, card); /* release interrupt */ - release_region(card->iobase + PCI9050_INTR_REG, 1); /* release all io ports */ - release_region(card->iobase + PCI9050_USER_IO, 1); - iounmap(card->dpram); - card->dpram = NULL; /* release shared mem */ -} /* ergo_releasehardware */ - - -/*********************************************************************************/ -/* acquire the needed hardware ports and map dpram. If an error occurs a nonzero */ -/* value is returned. */ -/* Use only during module init. */ -/*********************************************************************************/ -int -ergo_inithardware(hysdn_card *card) -{ - if (!request_region(card->iobase + PCI9050_INTR_REG, 1, "HYSDN")) - return (-1); - if (!request_region(card->iobase + PCI9050_USER_IO, 1, "HYSDN")) { - release_region(card->iobase + PCI9050_INTR_REG, 1); - return (-1); /* ports already in use */ - } - card->memend = card->membase + ERG_DPRAM_PAGE_SIZE - 1; - if (!(card->dpram = ioremap(card->membase, ERG_DPRAM_PAGE_SIZE))) { - release_region(card->iobase + PCI9050_INTR_REG, 1); - release_region(card->iobase + PCI9050_USER_IO, 1); - return (-1); - } - - ergo_stopcard(card); /* disable interrupts */ - if (request_irq(card->irq, ergo_interrupt, IRQF_SHARED, "HYSDN", card)) { - ergo_releasehardware(card); /* return the acquired hardware */ - return (-1); - } - /* success, now setup the function pointers */ - card->stopcard = ergo_stopcard; - card->releasehardware = ergo_releasehardware; - card->testram = ergo_testram; - card->writebootimg = ergo_writebootimg; - card->writebootseq = ergo_writebootseq; - card->waitpofready = ergo_waitpofready; - card->set_errlog_state = ergo_set_errlog_state; - INIT_WORK(&card->irq_queue, ergo_irq_bh); - spin_lock_init(&card->hysdn_lock); - - return (0); -} /* ergo_inithardware */ diff --git a/drivers/staging/isdn/hysdn/boardergo.h b/drivers/staging/isdn/hysdn/boardergo.h deleted file mode 100644 index e99bd81c4034..000000000000 --- a/drivers/staging/isdn/hysdn/boardergo.h +++ /dev/null @@ -1,100 +0,0 @@ -/* $Id: boardergo.h,v 1.2.6.1 2001/09/23 22:24:54 kai Exp $ - * - * Linux driver for HYSDN cards, definitions for ergo type boards (buffers..). - * - * Author Werner Cornelius (werner@titro.de) for Hypercope GmbH - * Copyright 1999 by Werner Cornelius (werner@titro.de) - * - * This software may be used and distributed according to the terms - * of the GNU General Public License, incorporated herein by reference. - * - */ - - -/************************************************/ -/* defines for the dual port memory of the card */ -/************************************************/ -#define ERG_DPRAM_PAGE_SIZE 0x2000 /* DPRAM occupies a 8K page */ -#define BOOT_IMG_SIZE 4096 -#define ERG_DPRAM_FILL_SIZE (ERG_DPRAM_PAGE_SIZE - BOOT_IMG_SIZE) - -#define ERG_TO_HY_BUF_SIZE 0x0E00 /* 3072 bytes buffer size to card */ -#define ERG_TO_PC_BUF_SIZE 0x0E00 /* 3072 bytes to PC, too */ - -/* following DPRAM layout copied from OS2-driver boarderg.h */ -typedef struct ErgDpram_tag { - /*0000 */ unsigned char ToHyBuf[ERG_TO_HY_BUF_SIZE]; - /*0E00 */ unsigned char ToPcBuf[ERG_TO_PC_BUF_SIZE]; - - /*1C00 */ unsigned char bSoftUart[SIZE_RSV_SOFT_UART]; - /* size 0x1B0 */ - - /*1DB0 *//* tErrLogEntry */ unsigned char volatile ErrLogMsg[64]; - /* size 64 bytes */ - /*1DB0 unsigned long ulErrType; */ - /*1DB4 unsigned long ulErrSubtype; */ - /*1DB8 unsigned long ucTextSize; */ - /*1DB9 unsigned long ucText[ERRLOG_TEXT_SIZE]; *//* ASCIIZ of len ucTextSize-1 */ - /*1DF0 */ - - /*1DF0 */ unsigned short volatile ToHyChannel; - /*1DF2 */ unsigned short volatile ToHySize; - /*1DF4 */ unsigned char volatile ToHyFlag; - /* !=0: msg for Hy waiting */ - /*1DF5 */ unsigned char volatile ToPcFlag; - /* !=0: msg for PC waiting */ - /*1DF6 */ unsigned short volatile ToPcChannel; - /*1DF8 */ unsigned short volatile ToPcSize; - /*1DFA */ unsigned char bRes1DBA[0x1E00 - 0x1DFA]; - /* 6 bytes */ - - /*1E00 */ unsigned char bRestOfEntryTbl[0x1F00 - 0x1E00]; - /*1F00 */ unsigned long TrapTable[62]; - /*1FF8 */ unsigned char bRes1FF8[0x1FFB - 0x1FF8]; - /* low part of reset vetor */ - /*1FFB */ unsigned char ToPcIntMetro; - /* notes: - * - metro has 32-bit boot ram - accessing - * ToPcInt and ToHyInt would be the same; - * so we moved ToPcInt to 1FFB. - * Because on the PC side both vars are - * readonly (reseting on int from E1 to PC), - * we can read both vars on both cards - * without destroying anything. - * - 1FFB is the high byte of the reset vector, - * so E1 side should NOT change this byte - * when writing! - */ - /*1FFC */ unsigned char volatile ToHyNoDpramErrLog; - /* note: ToHyNoDpramErrLog is used to inform - * boot loader, not to use DPRAM based - * ErrLog; when DOS driver is rewritten - * this becomes obsolete - */ - /*1FFD */ unsigned char bRes1FFD; - /*1FFE */ unsigned char ToPcInt; - /* E1_intclear; on CHAMP2: E1_intset */ - /*1FFF */ unsigned char ToHyInt; - /* E1_intset; on CHAMP2: E1_intclear */ -} tErgDpram; - -/**********************************************/ -/* PCI9050 controller local register offsets: */ -/* copied from boarderg.c */ -/**********************************************/ -#define PCI9050_INTR_REG 0x4C /* Interrupt register */ -#define PCI9050_USER_IO 0x51 /* User I/O register */ - -/* bitmask for PCI9050_INTR_REG: */ -#define PCI9050_INTR_REG_EN1 0x01 /* 1= enable (def.), 0= disable */ -#define PCI9050_INTR_REG_POL1 0x02 /* 1= active high (def.), 0= active low */ -#define PCI9050_INTR_REG_STAT1 0x04 /* 1= intr. active, 0= intr. not active (def.) */ -#define PCI9050_INTR_REG_ENPCI 0x40 /* 1= PCI interrupts enable (def.) */ - -/* bitmask for PCI9050_USER_IO: */ -#define PCI9050_USER_IO_EN3 0x02 /* 1= disable , 0= enable (def.) */ -#define PCI9050_USER_IO_DIR3 0x04 /* 1= output (def.), 0= input */ -#define PCI9050_USER_IO_DAT3 0x08 /* 1= high (def.) , 0= low */ - -#define PCI9050_E1_RESET (PCI9050_USER_IO_DIR3) /* 0x04 */ -#define PCI9050_E1_RUN (PCI9050_USER_IO_DAT3 | PCI9050_USER_IO_DIR3) /* 0x0C */ diff --git a/drivers/staging/isdn/hysdn/hycapi.c b/drivers/staging/isdn/hysdn/hycapi.c deleted file mode 100644 index a2c15cd7bf67..000000000000 --- a/drivers/staging/isdn/hysdn/hycapi.c +++ /dev/null @@ -1,785 +0,0 @@ -/* $Id: hycapi.c,v 1.8.6.4 2001/09/23 22:24:54 kai Exp $ - * - * Linux driver for HYSDN cards, CAPI2.0-Interface. - * - * Author Ulrich Albrecht <u.albrecht@hypercope.de> for Hypercope GmbH - * Copyright 2000 by Hypercope GmbH - * - * This software may be used and distributed according to the terms - * of the GNU General Public License, incorporated herein by reference. - * - */ - -#include <linux/module.h> -#include <linux/proc_fs.h> -#include <linux/seq_file.h> -#include <linux/signal.h> -#include <linux/kernel.h> -#include <linux/skbuff.h> -#include <linux/netdevice.h> -#include <linux/slab.h> - -#define VER_DRIVER 0 -#define VER_CARDTYPE 1 -#define VER_HWID 2 -#define VER_SERIAL 3 -#define VER_OPTION 4 -#define VER_PROTO 5 -#define VER_PROFILE 6 -#define VER_CAPI 7 - -#include "hysdn_defs.h" -#include <linux/kernelcapi.h> - -static char hycapi_revision[] = "$Revision: 1.8.6.4 $"; - -unsigned int hycapi_enable = 0xffffffff; -module_param(hycapi_enable, uint, 0); - -typedef struct _hycapi_appl { - unsigned int ctrl_mask; - capi_register_params rp; - struct sk_buff *listen_req[CAPI_MAXCONTR]; -} hycapi_appl; - -static hycapi_appl hycapi_applications[CAPI_MAXAPPL]; - -static u16 hycapi_send_message(struct capi_ctr *ctrl, struct sk_buff *skb); - -static inline int _hycapi_appCheck(int app_id, int ctrl_no) -{ - if ((ctrl_no <= 0) || (ctrl_no > CAPI_MAXCONTR) || (app_id <= 0) || - (app_id > CAPI_MAXAPPL)) - { - printk(KERN_ERR "HYCAPI: Invalid request app_id %d for controller %d", app_id, ctrl_no); - return -1; - } - return ((hycapi_applications[app_id - 1].ctrl_mask & (1 << (ctrl_no-1))) != 0); -} - -/****************************** -Kernel-Capi callback reset_ctr -******************************/ - -static void -hycapi_reset_ctr(struct capi_ctr *ctrl) -{ - hycapictrl_info *cinfo = ctrl->driverdata; - -#ifdef HYCAPI_PRINTFNAMES - printk(KERN_NOTICE "HYCAPI hycapi_reset_ctr\n"); -#endif - capilib_release(&cinfo->ncci_head); - capi_ctr_down(ctrl); -} - -/****************************** -Kernel-Capi callback remove_ctr -******************************/ - -static void -hycapi_remove_ctr(struct capi_ctr *ctrl) -{ - int i; - hycapictrl_info *cinfo = NULL; - hysdn_card *card = NULL; -#ifdef HYCAPI_PRINTFNAMES - printk(KERN_NOTICE "HYCAPI hycapi_remove_ctr\n"); -#endif - cinfo = (hycapictrl_info *)(ctrl->driverdata); - if (!cinfo) { - printk(KERN_ERR "No hycapictrl_info set!"); - return; - } - card = cinfo->card; - capi_ctr_suspend_output(ctrl); - for (i = 0; i < CAPI_MAXAPPL; i++) { - if (hycapi_applications[i].listen_req[ctrl->cnr - 1]) { - kfree_skb(hycapi_applications[i].listen_req[ctrl->cnr - 1]); - hycapi_applications[i].listen_req[ctrl->cnr - 1] = NULL; - } - } - detach_capi_ctr(ctrl); - ctrl->driverdata = NULL; - kfree(card->hyctrlinfo); - - - card->hyctrlinfo = NULL; -} - -/*********************************************************** - -Queue a CAPI-message to the controller. - -***********************************************************/ - -static void -hycapi_sendmsg_internal(struct capi_ctr *ctrl, struct sk_buff *skb) -{ - hycapictrl_info *cinfo = (hycapictrl_info *)(ctrl->driverdata); - hysdn_card *card = cinfo->card; - - spin_lock_irq(&cinfo->lock); -#ifdef HYCAPI_PRINTFNAMES - printk(KERN_NOTICE "hycapi_send_message\n"); -#endif - cinfo->skbs[cinfo->in_idx++] = skb; /* add to buffer list */ - if (cinfo->in_idx >= HYSDN_MAX_CAPI_SKB) - cinfo->in_idx = 0; /* wrap around */ - cinfo->sk_count++; /* adjust counter */ - if (cinfo->sk_count >= HYSDN_MAX_CAPI_SKB) { - /* inform upper layers we're full */ - printk(KERN_ERR "HYSDN Card%d: CAPI-buffer overrun!\n", - card->myid); - capi_ctr_suspend_output(ctrl); - } - cinfo->tx_skb = skb; - spin_unlock_irq(&cinfo->lock); - schedule_work(&card->irq_queue); -} - -/*********************************************************** -hycapi_register_internal - -Send down the CAPI_REGISTER-Command to the controller. -This functions will also be used if the adapter has been rebooted to -re-register any applications in the private list. - -************************************************************/ - -static void -hycapi_register_internal(struct capi_ctr *ctrl, __u16 appl, - capi_register_params *rp) -{ - char ExtFeatureDefaults[] = "49 /0/0/0/0,*/1,*/2,*/3,*/4,*/5,*/6,*/7,*/8,*/9,*"; - hycapictrl_info *cinfo = (hycapictrl_info *)(ctrl->driverdata); - hysdn_card *card = cinfo->card; - struct sk_buff *skb; - __u16 len; - __u8 _command = 0xa0, _subcommand = 0x80; - __u16 MessageNumber = 0x0000; - __u16 MessageBufferSize = 0; - int slen = strlen(ExtFeatureDefaults); -#ifdef HYCAPI_PRINTFNAMES - printk(KERN_NOTICE "hycapi_register_appl\n"); -#endif - MessageBufferSize = rp->level3cnt * rp->datablkcnt * rp->datablklen; - - len = CAPI_MSG_BASELEN + 8 + slen + 1; - if (!(skb = alloc_skb(len, GFP_ATOMIC))) { - printk(KERN_ERR "HYSDN card%d: memory squeeze in hycapi_register_appl\n", - card->myid); - return; - } - skb_put_data(skb, &len, sizeof(__u16)); - skb_put_data(skb, &appl, sizeof(__u16)); - skb_put_data(skb, &_command, sizeof(__u8)); - skb_put_data(skb, &_subcommand, sizeof(__u8)); - skb_put_data(skb, &MessageNumber, sizeof(__u16)); - skb_put_data(skb, &MessageBufferSize, sizeof(__u16)); - skb_put_data(skb, &(rp->level3cnt), sizeof(__u16)); - skb_put_data(skb, &(rp->datablkcnt), sizeof(__u16)); - skb_put_data(skb, &(rp->datablklen), sizeof(__u16)); - skb_put_data(skb, ExtFeatureDefaults, slen); - hycapi_applications[appl - 1].ctrl_mask |= (1 << (ctrl->cnr - 1)); - hycapi_send_message(ctrl, skb); -} - -/************************************************************ -hycapi_restart_internal - -After an adapter has been rebootet, re-register all applications and -send a LISTEN_REQ (if there has been such a thing ) - -*************************************************************/ - -static void hycapi_restart_internal(struct capi_ctr *ctrl) -{ - int i; - struct sk_buff *skb; -#ifdef HYCAPI_PRINTFNAMES - printk(KERN_WARNING "HYSDN: hycapi_restart_internal"); -#endif - for (i = 0; i < CAPI_MAXAPPL; i++) { - if (_hycapi_appCheck(i + 1, ctrl->cnr) == 1) { - hycapi_register_internal(ctrl, i + 1, - &hycapi_applications[i].rp); - if (hycapi_applications[i].listen_req[ctrl->cnr - 1]) { - skb = skb_copy(hycapi_applications[i].listen_req[ctrl->cnr - 1], GFP_ATOMIC); - hycapi_sendmsg_internal(ctrl, skb); - } - } - } -} - -/************************************************************* -Register an application. -Error-checking is done for CAPI-compliance. - -The application is recorded in the internal list. -*************************************************************/ - -static void -hycapi_register_appl(struct capi_ctr *ctrl, __u16 appl, - capi_register_params *rp) -{ - int MaxLogicalConnections = 0, MaxBDataBlocks = 0, MaxBDataLen = 0; - hycapictrl_info *cinfo = (hycapictrl_info *)(ctrl->driverdata); - hysdn_card *card = cinfo->card; - int chk = _hycapi_appCheck(appl, ctrl->cnr); - if (chk < 0) { - return; - } - if (chk == 1) { - printk(KERN_INFO "HYSDN: apl %d already registered\n", appl); - return; - } - MaxBDataBlocks = rp->datablkcnt > CAPI_MAXDATAWINDOW ? CAPI_MAXDATAWINDOW : rp->datablkcnt; - rp->datablkcnt = MaxBDataBlocks; - MaxBDataLen = rp->datablklen < 1024 ? 1024 : rp->datablklen; - rp->datablklen = MaxBDataLen; - - MaxLogicalConnections = rp->level3cnt; - if (MaxLogicalConnections < 0) { - MaxLogicalConnections = card->bchans * -MaxLogicalConnections; - } - if (MaxLogicalConnections == 0) { - MaxLogicalConnections = card->bchans; - } - - rp->level3cnt = MaxLogicalConnections; - memcpy(&hycapi_applications[appl - 1].rp, - rp, sizeof(capi_register_params)); -} - -/********************************************************************* - -hycapi_release_internal - -Send down a CAPI_RELEASE to the controller. -*********************************************************************/ - -static void hycapi_release_internal(struct capi_ctr *ctrl, __u16 appl) -{ - hycapictrl_info *cinfo = (hycapictrl_info *)(ctrl->driverdata); - hysdn_card *card = cinfo->card; - struct sk_buff *skb; - __u16 len; - __u8 _command = 0xa1, _subcommand = 0x80; - __u16 MessageNumber = 0x0000; - - capilib_release_appl(&cinfo->ncci_head, appl); - -#ifdef HYCAPI_PRINTFNAMES - printk(KERN_NOTICE "hycapi_release_appl\n"); -#endif - len = CAPI_MSG_BASELEN; - if (!(skb = alloc_skb(len, GFP_ATOMIC))) { - printk(KERN_ERR "HYSDN card%d: memory squeeze in hycapi_register_appl\n", - card->myid); - return; - } - skb_put_data(skb, &len, sizeof(__u16)); - skb_put_data(skb, &appl, sizeof(__u16)); - skb_put_data(skb, &_command, sizeof(__u8)); - skb_put_data(skb, &_subcommand, sizeof(__u8)); - skb_put_data(skb, &MessageNumber, sizeof(__u16)); - hycapi_send_message(ctrl, skb); - hycapi_applications[appl - 1].ctrl_mask &= ~(1 << (ctrl->cnr - 1)); -} - -/****************************************************************** -hycapi_release_appl - -Release the application from the internal list an remove it's -registration at controller-level -******************************************************************/ - -static void -hycapi_release_appl(struct capi_ctr *ctrl, __u16 appl) -{ - int chk; - - chk = _hycapi_appCheck(appl, ctrl->cnr); - if (chk < 0) { - printk(KERN_ERR "HYCAPI: Releasing invalid appl %d on controller %d\n", appl, ctrl->cnr); - return; - } - if (hycapi_applications[appl - 1].listen_req[ctrl->cnr - 1]) { - kfree_skb(hycapi_applications[appl - 1].listen_req[ctrl->cnr - 1]); - hycapi_applications[appl - 1].listen_req[ctrl->cnr - 1] = NULL; - } - if (chk == 1) - { - hycapi_release_internal(ctrl, appl); - } -} - - -/************************************************************** -Kill a single controller. -**************************************************************/ - -int hycapi_capi_release(hysdn_card *card) -{ - hycapictrl_info *cinfo = card->hyctrlinfo; - struct capi_ctr *ctrl; -#ifdef HYCAPI_PRINTFNAMES - printk(KERN_NOTICE "hycapi_capi_release\n"); -#endif - if (cinfo) { - ctrl = &cinfo->capi_ctrl; - hycapi_remove_ctr(ctrl); - } - return 0; -} - -/************************************************************** -hycapi_capi_stop - -Stop CAPI-Output on a card. (e.g. during reboot) -***************************************************************/ - -int hycapi_capi_stop(hysdn_card *card) -{ - hycapictrl_info *cinfo = card->hyctrlinfo; - struct capi_ctr *ctrl; -#ifdef HYCAPI_PRINTFNAMES - printk(KERN_NOTICE "hycapi_capi_stop\n"); -#endif - if (cinfo) { - ctrl = &cinfo->capi_ctrl; -/* ctrl->suspend_output(ctrl); */ - capi_ctr_down(ctrl); - } - return 0; -} - -/*************************************************************** -hycapi_send_message - -Send a message to the controller. - -Messages are parsed for their Command/Subcommand-type, and appropriate -action's are performed. - -Note that we have to muck around with a 64Bit-DATA_REQ as there are -firmware-releases that do not check the MsgLen-Indication! - -***************************************************************/ - -static u16 hycapi_send_message(struct capi_ctr *ctrl, struct sk_buff *skb) -{ - __u16 appl_id; - int _len, _len2; - __u8 msghead[64]; - hycapictrl_info *cinfo = ctrl->driverdata; - u16 retval = CAPI_NOERROR; - - appl_id = CAPIMSG_APPID(skb->data); - switch (_hycapi_appCheck(appl_id, ctrl->cnr)) - { - case 0: -/* printk(KERN_INFO "Need to register\n"); */ - hycapi_register_internal(ctrl, - appl_id, - &(hycapi_applications[appl_id - 1].rp)); - break; - case 1: - break; - default: - printk(KERN_ERR "HYCAPI: Controller mixup!\n"); - retval = CAPI_ILLAPPNR; - goto out; - } - switch (CAPIMSG_CMD(skb->data)) { - case CAPI_DISCONNECT_B3_RESP: - capilib_free_ncci(&cinfo->ncci_head, appl_id, - CAPIMSG_NCCI(skb->data)); - break; - case CAPI_DATA_B3_REQ: - _len = CAPIMSG_LEN(skb->data); - if (_len > 22) { - _len2 = _len - 22; - skb_copy_from_linear_data(skb, msghead, 22); - skb_copy_to_linear_data_offset(skb, _len2, - msghead, 22); - skb_pull(skb, _len2); - CAPIMSG_SETLEN(skb->data, 22); - retval = capilib_data_b3_req(&cinfo->ncci_head, - CAPIMSG_APPID(skb->data), - CAPIMSG_NCCI(skb->data), - CAPIMSG_MSGID(skb->data)); - } - break; - case CAPI_LISTEN_REQ: - if (hycapi_applications[appl_id - 1].listen_req[ctrl->cnr - 1]) - { - kfree_skb(hycapi_applications[appl_id - 1].listen_req[ctrl->cnr - 1]); - hycapi_applications[appl_id - 1].listen_req[ctrl->cnr - 1] = NULL; - } - if (!(hycapi_applications[appl_id -1].listen_req[ctrl->cnr - 1] = skb_copy(skb, GFP_ATOMIC))) - { - printk(KERN_ERR "HYSDN: memory squeeze in private_listen\n"); - } - break; - default: - break; - } -out: - if (retval == CAPI_NOERROR) - hycapi_sendmsg_internal(ctrl, skb); - else - dev_kfree_skb_any(skb); - - return retval; -} - -static int hycapi_proc_show(struct seq_file *m, void *v) -{ - struct capi_ctr *ctrl = m->private; - hycapictrl_info *cinfo = (hycapictrl_info *)(ctrl->driverdata); - hysdn_card *card = cinfo->card; - char *s; - - seq_printf(m, "%-16s %s\n", "name", cinfo->cardname); - seq_printf(m, "%-16s 0x%x\n", "io", card->iobase); - seq_printf(m, "%-16s %d\n", "irq", card->irq); - - switch (card->brdtype) { - case BD_PCCARD: s = "HYSDN Hycard"; break; - case BD_ERGO: s = "HYSDN Ergo2"; break; - case BD_METRO: s = "HYSDN Metro4"; break; - case BD_CHAMP2: s = "HYSDN Champ2"; break; - case BD_PLEXUS: s = "HYSDN Plexus30"; break; - default: s = "???"; break; - } - seq_printf(m, "%-16s %s\n", "type", s); - if ((s = cinfo->version[VER_DRIVER]) != NULL) - seq_printf(m, "%-16s %s\n", "ver_driver", s); - if ((s = cinfo->version[VER_CARDTYPE]) != NULL) - seq_printf(m, "%-16s %s\n", "ver_cardtype", s); - if ((s = cinfo->version[VER_SERIAL]) != NULL) - seq_printf(m, "%-16s %s\n", "ver_serial", s); - - seq_printf(m, "%-16s %s\n", "cardname", cinfo->cardname); - - return 0; -} - -/************************************************************** -hycapi_load_firmware - -This does NOT load any firmware, but the callback somehow is needed -on capi-interface registration. - -**************************************************************/ - -static int hycapi_load_firmware(struct capi_ctr *ctrl, capiloaddata *data) -{ -#ifdef HYCAPI_PRINTFNAMES - printk(KERN_NOTICE "hycapi_load_firmware\n"); -#endif - return 0; -} - - -static char *hycapi_procinfo(struct capi_ctr *ctrl) -{ - hycapictrl_info *cinfo = (hycapictrl_info *)(ctrl->driverdata); -#ifdef HYCAPI_PRINTFNAMES - printk(KERN_NOTICE "%s\n", __func__); -#endif - if (!cinfo) - return ""; - sprintf(cinfo->infobuf, "%s %s 0x%x %d %s", - cinfo->cardname[0] ? cinfo->cardname : "-", - cinfo->version[VER_DRIVER] ? cinfo->version[VER_DRIVER] : "-", - cinfo->card ? cinfo->card->iobase : 0x0, - cinfo->card ? cinfo->card->irq : 0, - hycapi_revision - ); - return cinfo->infobuf; -} - -/****************************************************************** -hycapi_rx_capipkt - -Receive a capi-message. - -All B3_DATA_IND are converted to 64K-extension compatible format. -New nccis are created if necessary. -*******************************************************************/ - -void -hycapi_rx_capipkt(hysdn_card *card, unsigned char *buf, unsigned short len) -{ - struct sk_buff *skb; - hycapictrl_info *cinfo = card->hyctrlinfo; - struct capi_ctr *ctrl; - __u16 ApplId; - __u16 MsgLen, info; - __u16 len2, CapiCmd; - __u32 CP64[2] = {0, 0}; -#ifdef HYCAPI_PRINTFNAMES - printk(KERN_NOTICE "hycapi_rx_capipkt\n"); -#endif - if (!cinfo) { - return; - } - ctrl = &cinfo->capi_ctrl; - if (len < CAPI_MSG_BASELEN) { - printk(KERN_ERR "HYSDN Card%d: invalid CAPI-message, length %d!\n", - card->myid, len); - return; - } - MsgLen = CAPIMSG_LEN(buf); - ApplId = CAPIMSG_APPID(buf); - CapiCmd = CAPIMSG_CMD(buf); - - if ((CapiCmd == CAPI_DATA_B3_IND) && (MsgLen < 30)) { - len2 = len + (30 - MsgLen); - if (!(skb = alloc_skb(len2, GFP_ATOMIC))) { - printk(KERN_ERR "HYSDN Card%d: incoming packet dropped\n", - card->myid); - return; - } - skb_put_data(skb, buf, MsgLen); - skb_put_data(skb, CP64, 2 * sizeof(__u32)); - skb_put_data(skb, buf + MsgLen, len - MsgLen); - CAPIMSG_SETLEN(skb->data, 30); - } else { - if (!(skb = alloc_skb(len, GFP_ATOMIC))) { - printk(KERN_ERR "HYSDN Card%d: incoming packet dropped\n", - card->myid); - return; - } - skb_put_data(skb, buf, len); - } - switch (CAPIMSG_CMD(skb->data)) - { - case CAPI_CONNECT_B3_CONF: -/* Check info-field for error-indication: */ - info = CAPIMSG_U16(skb->data, 12); - switch (info) - { - case 0: - capilib_new_ncci(&cinfo->ncci_head, ApplId, CAPIMSG_NCCI(skb->data), - hycapi_applications[ApplId - 1].rp.datablkcnt); - - break; - case 0x0001: - printk(KERN_ERR "HYSDN Card%d: NCPI not supported by current " - "protocol. NCPI ignored.\n", card->myid); - break; - case 0x2001: - printk(KERN_ERR "HYSDN Card%d: Message not supported in" - " current state\n", card->myid); - break; - case 0x2002: - printk(KERN_ERR "HYSDN Card%d: invalid PLCI\n", card->myid); - break; - case 0x2004: - printk(KERN_ERR "HYSDN Card%d: out of NCCI\n", card->myid); - break; - case 0x3008: - printk(KERN_ERR "HYSDN Card%d: NCPI not supported\n", - card->myid); - break; - default: - printk(KERN_ERR "HYSDN Card%d: Info in CONNECT_B3_CONF: %d\n", - card->myid, info); - break; - } - break; - case CAPI_CONNECT_B3_IND: - capilib_new_ncci(&cinfo->ncci_head, ApplId, - CAPIMSG_NCCI(skb->data), - hycapi_applications[ApplId - 1].rp.datablkcnt); - break; - case CAPI_DATA_B3_CONF: - capilib_data_b3_conf(&cinfo->ncci_head, ApplId, - CAPIMSG_NCCI(skb->data), - CAPIMSG_MSGID(skb->data)); - break; - default: - break; - } - capi_ctr_handle_message(ctrl, ApplId, skb); -} - -/****************************************************************** -hycapi_tx_capiack - -Internally acknowledge a msg sent. This will remove the msg from the -internal queue. - -*******************************************************************/ - -void hycapi_tx_capiack(hysdn_card *card) -{ - hycapictrl_info *cinfo = card->hyctrlinfo; -#ifdef HYCAPI_PRINTFNAMES - printk(KERN_NOTICE "hycapi_tx_capiack\n"); -#endif - if (!cinfo) { - return; - } - spin_lock_irq(&cinfo->lock); - kfree_skb(cinfo->skbs[cinfo->out_idx]); /* free skb */ - cinfo->skbs[cinfo->out_idx++] = NULL; - if (cinfo->out_idx >= HYSDN_MAX_CAPI_SKB) - cinfo->out_idx = 0; /* wrap around */ - - if (cinfo->sk_count-- == HYSDN_MAX_CAPI_SKB) /* dec usage count */ - capi_ctr_resume_output(&cinfo->capi_ctrl); - spin_unlock_irq(&cinfo->lock); -} - -/*************************************************************** -hycapi_tx_capiget(hysdn_card *card) - -This is called when polling for messages to SEND. - -****************************************************************/ - -struct sk_buff * -hycapi_tx_capiget(hysdn_card *card) -{ - hycapictrl_info *cinfo = card->hyctrlinfo; - if (!cinfo) { - return (struct sk_buff *)NULL; - } - if (!cinfo->sk_count) - return (struct sk_buff *)NULL; /* nothing available */ - - return (cinfo->skbs[cinfo->out_idx]); /* next packet to send */ -} - - -/********************************************************** -int hycapi_init() - -attach the capi-driver to the kernel-capi. - -***********************************************************/ - -int hycapi_init(void) -{ - int i; - for (i = 0; i < CAPI_MAXAPPL; i++) { - memset(&(hycapi_applications[i]), 0, sizeof(hycapi_appl)); - } - return (0); -} - -/************************************************************** -hycapi_cleanup(void) - -detach the capi-driver to the kernel-capi. Actually this should -free some more ressources. Do that later. -**************************************************************/ - -void -hycapi_cleanup(void) -{ -} - -/******************************************************************** -hycapi_capi_create(hysdn_card *card) - -Attach the card with its capi-ctrl. -*********************************************************************/ - -static void hycapi_fill_profile(hysdn_card *card) -{ - hycapictrl_info *cinfo = NULL; - struct capi_ctr *ctrl = NULL; - cinfo = card->hyctrlinfo; - if (!cinfo) return; - ctrl = &cinfo->capi_ctrl; - strcpy(ctrl->manu, "Hypercope"); - ctrl->version.majorversion = 2; - ctrl->version.minorversion = 0; - ctrl->version.majormanuversion = 3; - ctrl->version.minormanuversion = 2; - ctrl->profile.ncontroller = card->myid; - ctrl->profile.nbchannel = card->bchans; - ctrl->profile.goptions = GLOBAL_OPTION_INTERNAL_CONTROLLER | - GLOBAL_OPTION_B_CHANNEL_OPERATION; - ctrl->profile.support1 = B1_PROT_64KBIT_HDLC | - (card->faxchans ? B1_PROT_T30 : 0) | - B1_PROT_64KBIT_TRANSPARENT; - ctrl->profile.support2 = B2_PROT_ISO7776 | - (card->faxchans ? B2_PROT_T30 : 0) | - B2_PROT_TRANSPARENT; - ctrl->profile.support3 = B3_PROT_TRANSPARENT | - B3_PROT_T90NL | - (card->faxchans ? B3_PROT_T30 : 0) | - (card->faxchans ? B3_PROT_T30EXT : 0) | - B3_PROT_ISO8208; -} - -int -hycapi_capi_create(hysdn_card *card) -{ - hycapictrl_info *cinfo = NULL; - struct capi_ctr *ctrl = NULL; - int retval; -#ifdef HYCAPI_PRINTFNAMES - printk(KERN_NOTICE "hycapi_capi_create\n"); -#endif - if ((hycapi_enable & (1 << card->myid)) == 0) { - return 1; - } - if (!card->hyctrlinfo) { - cinfo = kzalloc(sizeof(hycapictrl_info), GFP_ATOMIC); - if (!cinfo) { - printk(KERN_WARNING "HYSDN: no memory for capi-ctrl.\n"); - return -ENOMEM; - } - card->hyctrlinfo = cinfo; - cinfo->card = card; - spin_lock_init(&cinfo->lock); - INIT_LIST_HEAD(&cinfo->ncci_head); - - switch (card->brdtype) { - case BD_PCCARD: strcpy(cinfo->cardname, "HYSDN Hycard"); break; - case BD_ERGO: strcpy(cinfo->cardname, "HYSDN Ergo2"); break; - case BD_METRO: strcpy(cinfo->cardname, "HYSDN Metro4"); break; - case BD_CHAMP2: strcpy(cinfo->cardname, "HYSDN Champ2"); break; - case BD_PLEXUS: strcpy(cinfo->cardname, "HYSDN Plexus30"); break; - default: strcpy(cinfo->cardname, "HYSDN ???"); break; - } - - ctrl = &cinfo->capi_ctrl; - ctrl->driver_name = "hycapi"; - ctrl->driverdata = cinfo; - ctrl->register_appl = hycapi_register_appl; - ctrl->release_appl = hycapi_release_appl; - ctrl->send_message = hycapi_send_message; - ctrl->load_firmware = hycapi_load_firmware; - ctrl->reset_ctr = hycapi_reset_ctr; - ctrl->procinfo = hycapi_procinfo; - ctrl->proc_show = hycapi_proc_show; - strcpy(ctrl->name, cinfo->cardname); - ctrl->owner = THIS_MODULE; - - retval = attach_capi_ctr(ctrl); - if (retval) { - printk(KERN_ERR "hycapi: attach controller failed.\n"); - return -EBUSY; - } - /* fill in the blanks: */ - hycapi_fill_profile(card); - capi_ctr_ready(ctrl); - } else { - /* resume output on stopped ctrl */ - ctrl = &card->hyctrlinfo->capi_ctrl; - hycapi_fill_profile(card); - capi_ctr_ready(ctrl); - hycapi_restart_internal(ctrl); -/* ctrl->resume_output(ctrl); */ - } - return 0; -} diff --git a/drivers/staging/isdn/hysdn/hysdn_boot.c b/drivers/staging/isdn/hysdn/hysdn_boot.c deleted file mode 100644 index ba177c3a621b..000000000000 --- a/drivers/staging/isdn/hysdn/hysdn_boot.c +++ /dev/null @@ -1,400 +0,0 @@ -/* $Id: hysdn_boot.c,v 1.4.6.4 2001/09/23 22:24:54 kai Exp $ - * - * Linux driver for HYSDN cards - * specific routines for booting and pof handling - * - * Author Werner Cornelius (werner@titro.de) for Hypercope GmbH - * Copyright 1999 by Werner Cornelius (werner@titro.de) - * - * This software may be used and distributed according to the terms - * of the GNU General Public License, incorporated herein by reference. - * - */ - -#include <linux/vmalloc.h> -#include <linux/slab.h> -#include <linux/uaccess.h> - -#include "hysdn_defs.h" -#include "hysdn_pof.h" - -/********************************/ -/* defines for pof read handler */ -/********************************/ -#define POF_READ_FILE_HEAD 0 -#define POF_READ_TAG_HEAD 1 -#define POF_READ_TAG_DATA 2 - -/************************************************************/ -/* definition of boot specific data area. This data is only */ -/* needed during boot and so allocated dynamically. */ -/************************************************************/ -struct boot_data { - unsigned short Cryptor; /* for use with Decrypt function */ - unsigned short Nrecs; /* records remaining in file */ - unsigned char pof_state;/* actual state of read handler */ - unsigned char is_crypted;/* card data is crypted */ - int BufSize; /* actual number of bytes bufferd */ - int last_error; /* last occurred error */ - unsigned short pof_recid;/* actual pof recid */ - unsigned long pof_reclen;/* total length of pof record data */ - unsigned long pof_recoffset;/* actual offset inside pof record */ - union { - unsigned char BootBuf[BOOT_BUF_SIZE];/* buffer as byte count */ - tPofRecHdr PofRecHdr; /* header for actual record/chunk */ - tPofFileHdr PofFileHdr; /* header from POF file */ - tPofTimeStamp PofTime; /* time information */ - } buf; -}; - -/*****************************************************/ -/* start decryption of successive POF file chuncks. */ -/* */ -/* to be called at start of POF file reading, */ -/* before starting any decryption on any POF record. */ -/*****************************************************/ -static void -StartDecryption(struct boot_data *boot) -{ - boot->Cryptor = CRYPT_STARTTERM; -} /* StartDecryption */ - - -/***************************************************************/ -/* decrypt complete BootBuf */ -/* NOTE: decryption must be applied to all or none boot tags - */ -/* to HI and LO boot loader and (all) seq tags, because */ -/* global Cryptor is started for whole POF. */ -/***************************************************************/ -static void -DecryptBuf(struct boot_data *boot, int cnt) -{ - unsigned char *bufp = boot->buf.BootBuf; - - while (cnt--) { - boot->Cryptor = (boot->Cryptor >> 1) ^ ((boot->Cryptor & 1U) ? CRYPT_FEEDTERM : 0); - *bufp++ ^= (unsigned char)boot->Cryptor; - } -} /* DecryptBuf */ - -/********************************************************************************/ -/* pof_handle_data executes the required actions dependent on the active record */ -/* id. If successful 0 is returned, a negative value shows an error. */ -/********************************************************************************/ -static int -pof_handle_data(hysdn_card *card, int datlen) -{ - struct boot_data *boot = card->boot; /* pointer to boot specific data */ - long l; - unsigned char *imgp; - int img_len; - - /* handle the different record types */ - switch (boot->pof_recid) { - - case TAG_TIMESTMP: - if (card->debug_flags & LOG_POF_RECORD) - hysdn_addlog(card, "POF created %s", boot->buf.PofTime.DateTimeText); - break; - - case TAG_CBOOTDTA: - DecryptBuf(boot, datlen); /* we need to encrypt the buffer */ - /* fall through */ - case TAG_BOOTDTA: - if (card->debug_flags & LOG_POF_RECORD) - hysdn_addlog(card, "POF got %s len=%d offs=0x%lx", - (boot->pof_recid == TAG_CBOOTDTA) ? "CBOOTDATA" : "BOOTDTA", - datlen, boot->pof_recoffset); - - if (boot->pof_reclen != POF_BOOT_LOADER_TOTAL_SIZE) { - boot->last_error = EPOF_BAD_IMG_SIZE; /* invalid length */ - return (boot->last_error); - } - imgp = boot->buf.BootBuf; /* start of buffer */ - img_len = datlen; /* maximum length to transfer */ - - l = POF_BOOT_LOADER_OFF_IN_PAGE - - (boot->pof_recoffset & (POF_BOOT_LOADER_PAGE_SIZE - 1)); - if (l > 0) { - /* buffer needs to be truncated */ - imgp += l; /* advance pointer */ - img_len -= l; /* adjust len */ - } - /* at this point no special handling for data wrapping over buffer */ - /* is necessary, because the boot image always will be adjusted to */ - /* match a page boundary inside the buffer. */ - /* The buffer for the boot image on the card is filled in 2 cycles */ - /* first the 1024 hi-words are put in the buffer, then the low 1024 */ - /* word are handled in the same way with different offset. */ - - if (img_len > 0) { - /* data available for copy */ - if ((boot->last_error = - card->writebootimg(card, imgp, - (boot->pof_recoffset > POF_BOOT_LOADER_PAGE_SIZE) ? 2 : 0)) < 0) - return (boot->last_error); - } - break; /* end of case boot image hi/lo */ - - case TAG_CABSDATA: - DecryptBuf(boot, datlen); /* we need to encrypt the buffer */ - /* fall through */ - case TAG_ABSDATA: - if (card->debug_flags & LOG_POF_RECORD) - hysdn_addlog(card, "POF got %s len=%d offs=0x%lx", - (boot->pof_recid == TAG_CABSDATA) ? "CABSDATA" : "ABSDATA", - datlen, boot->pof_recoffset); - - if ((boot->last_error = card->writebootseq(card, boot->buf.BootBuf, datlen)) < 0) - return (boot->last_error); /* error writing data */ - - if (boot->pof_recoffset + datlen >= boot->pof_reclen) - return (card->waitpofready(card)); /* data completely spooled, wait for ready */ - - break; /* end of case boot seq data */ - - default: - if (card->debug_flags & LOG_POF_RECORD) - hysdn_addlog(card, "POF got data(id=0x%lx) len=%d offs=0x%lx", boot->pof_recid, - datlen, boot->pof_recoffset); - - break; /* simply skip record */ - } /* switch boot->pof_recid */ - - return (0); -} /* pof_handle_data */ - - -/******************************************************************************/ -/* pof_write_buffer is called when the buffer has been filled with the needed */ -/* number of data bytes. The number delivered is additionally supplied for */ -/* verification. The functions handles the data and returns the needed number */ -/* of bytes for the next action. If the returned value is 0 or less an error */ -/* occurred and booting must be aborted. */ -/******************************************************************************/ -int -pof_write_buffer(hysdn_card *card, int datlen) -{ - struct boot_data *boot = card->boot; /* pointer to boot specific data */ - - if (!boot) - return (-EFAULT); /* invalid call */ - if (boot->last_error < 0) - return (boot->last_error); /* repeated error */ - - if (card->debug_flags & LOG_POF_WRITE) - hysdn_addlog(card, "POF write: got %d bytes ", datlen); - - switch (boot->pof_state) { - case POF_READ_FILE_HEAD: - if (card->debug_flags & LOG_POF_WRITE) - hysdn_addlog(card, "POF write: checking file header"); - - if (datlen != sizeof(tPofFileHdr)) { - boot->last_error = -EPOF_INTERNAL; - break; - } - if (boot->buf.PofFileHdr.Magic != TAGFILEMAGIC) { - boot->last_error = -EPOF_BAD_MAGIC; - break; - } - /* Setup the new state and vars */ - boot->Nrecs = (unsigned short)(boot->buf.PofFileHdr.N_PofRecs); /* limited to 65535 */ - boot->pof_state = POF_READ_TAG_HEAD; /* now start with single tags */ - boot->last_error = sizeof(tPofRecHdr); /* new length */ - break; - - case POF_READ_TAG_HEAD: - if (card->debug_flags & LOG_POF_WRITE) - hysdn_addlog(card, "POF write: checking tag header"); - - if (datlen != sizeof(tPofRecHdr)) { - boot->last_error = -EPOF_INTERNAL; - break; - } - boot->pof_recid = boot->buf.PofRecHdr.PofRecId; /* actual pof recid */ - boot->pof_reclen = boot->buf.PofRecHdr.PofRecDataLen; /* total length */ - boot->pof_recoffset = 0; /* no starting offset */ - - if (card->debug_flags & LOG_POF_RECORD) - hysdn_addlog(card, "POF: got record id=0x%lx length=%ld ", - boot->pof_recid, boot->pof_reclen); - - boot->pof_state = POF_READ_TAG_DATA; /* now start with tag data */ - if (boot->pof_reclen < BOOT_BUF_SIZE) - boot->last_error = boot->pof_reclen; /* limit size */ - else - boot->last_error = BOOT_BUF_SIZE; /* maximum */ - - if (!boot->last_error) { /* no data inside record */ - boot->pof_state = POF_READ_TAG_HEAD; /* now start with single tags */ - boot->last_error = sizeof(tPofRecHdr); /* new length */ - } - break; - - case POF_READ_TAG_DATA: - if (card->debug_flags & LOG_POF_WRITE) - hysdn_addlog(card, "POF write: getting tag data"); - - if (datlen != boot->last_error) { - boot->last_error = -EPOF_INTERNAL; - break; - } - if ((boot->last_error = pof_handle_data(card, datlen)) < 0) - return (boot->last_error); /* an error occurred */ - boot->pof_recoffset += datlen; - if (boot->pof_recoffset >= boot->pof_reclen) { - boot->pof_state = POF_READ_TAG_HEAD; /* now start with single tags */ - boot->last_error = sizeof(tPofRecHdr); /* new length */ - } else { - if (boot->pof_reclen - boot->pof_recoffset < BOOT_BUF_SIZE) - boot->last_error = boot->pof_reclen - boot->pof_recoffset; /* limit size */ - else - boot->last_error = BOOT_BUF_SIZE; /* maximum */ - } - break; - - default: - boot->last_error = -EPOF_INTERNAL; /* unknown state */ - break; - } /* switch (boot->pof_state) */ - - return (boot->last_error); -} /* pof_write_buffer */ - - -/*******************************************************************************/ -/* pof_write_open is called when an open for boot on the cardlog device occurs. */ -/* The function returns the needed number of bytes for the next operation. If */ -/* the returned number is less or equal 0 an error specified by this code */ -/* occurred. Additionally the pointer to the buffer data area is set on success */ -/*******************************************************************************/ -int -pof_write_open(hysdn_card *card, unsigned char **bufp) -{ - struct boot_data *boot; /* pointer to boot specific data */ - - if (card->boot) { - if (card->debug_flags & LOG_POF_OPEN) - hysdn_addlog(card, "POF open: already opened for boot"); - return (-ERR_ALREADY_BOOT); /* boot already active */ - } - /* error no mem available */ - if (!(boot = kzalloc(sizeof(struct boot_data), GFP_KERNEL))) { - if (card->debug_flags & LOG_MEM_ERR) - hysdn_addlog(card, "POF open: unable to allocate mem"); - return (-EFAULT); - } - card->boot = boot; - card->state = CARD_STATE_BOOTING; - - card->stopcard(card); /* first stop the card */ - if (card->testram(card)) { - if (card->debug_flags & LOG_POF_OPEN) - hysdn_addlog(card, "POF open: DPRAM test failure"); - boot->last_error = -ERR_BOARD_DPRAM; - card->state = CARD_STATE_BOOTERR; /* show boot error */ - return (boot->last_error); - } - boot->BufSize = 0; /* Buffer is empty */ - boot->pof_state = POF_READ_FILE_HEAD; /* read file header */ - StartDecryption(boot); /* if POF File should be encrypted */ - - if (card->debug_flags & LOG_POF_OPEN) - hysdn_addlog(card, "POF open: success"); - - *bufp = boot->buf.BootBuf; /* point to buffer */ - return (sizeof(tPofFileHdr)); -} /* pof_write_open */ - -/********************************************************************************/ -/* pof_write_close is called when an close of boot on the cardlog device occurs. */ -/* The return value must be 0 if everything has happened as desired. */ -/********************************************************************************/ -int -pof_write_close(hysdn_card *card) -{ - struct boot_data *boot = card->boot; /* pointer to boot specific data */ - - if (!boot) - return (-EFAULT); /* invalid call */ - - card->boot = NULL; /* no boot active */ - kfree(boot); - - if (card->state == CARD_STATE_RUN) - card->set_errlog_state(card, 1); /* activate error log */ - - if (card->debug_flags & LOG_POF_OPEN) - hysdn_addlog(card, "POF close: success"); - - return (0); -} /* pof_write_close */ - -/*********************************************************************************/ -/* EvalSysrTokData checks additional records delivered with the Sysready Message */ -/* when POF has been booted. A return value of 0 is used if no error occurred. */ -/*********************************************************************************/ -int -EvalSysrTokData(hysdn_card *card, unsigned char *cp, int len) -{ - u_char *p; - u_char crc; - - if (card->debug_flags & LOG_POF_RECORD) - hysdn_addlog(card, "SysReady Token data length %d", len); - - if (len < 2) { - hysdn_addlog(card, "SysReady Token Data to short"); - return (1); - } - for (p = cp, crc = 0; p < (cp + len - 2); p++) - if ((crc & 0x80)) - crc = (((u_char) (crc << 1)) + 1) + *p; - else - crc = ((u_char) (crc << 1)) + *p; - crc = ~crc; - if (crc != *(cp + len - 1)) { - hysdn_addlog(card, "SysReady Token Data invalid CRC"); - return (1); - } - len--; /* don't check CRC byte */ - while (len > 0) { - - if (*cp == SYSR_TOK_END) - return (0); /* End of Token stream */ - - if (len < (*(cp + 1) + 2)) { - hysdn_addlog(card, "token 0x%x invalid length %d", *cp, *(cp + 1)); - return (1); - } - switch (*cp) { - case SYSR_TOK_B_CHAN: /* 1 */ - if (*(cp + 1) != 1) - return (1); /* length invalid */ - card->bchans = *(cp + 2); - break; - - case SYSR_TOK_FAX_CHAN: /* 2 */ - if (*(cp + 1) != 1) - return (1); /* length invalid */ - card->faxchans = *(cp + 2); - break; - - case SYSR_TOK_MAC_ADDR: /* 3 */ - if (*(cp + 1) != 6) - return (1); /* length invalid */ - memcpy(card->mac_addr, cp + 2, 6); - break; - - default: - hysdn_addlog(card, "unknown token 0x%02x length %d", *cp, *(cp + 1)); - break; - } - len -= (*(cp + 1) + 2); /* adjust len */ - cp += (*(cp + 1) + 2); /* and pointer */ - } - - hysdn_addlog(card, "no end token found"); - return (1); -} /* EvalSysrTokData */ diff --git a/drivers/staging/isdn/hysdn/hysdn_defs.h b/drivers/staging/isdn/hysdn/hysdn_defs.h deleted file mode 100644 index cdac46a21692..000000000000 --- a/drivers/staging/isdn/hysdn/hysdn_defs.h +++ /dev/null @@ -1,282 +0,0 @@ -/* $Id: hysdn_defs.h,v 1.5.6.3 2001/09/23 22:24:54 kai Exp $ - * - * Linux driver for HYSDN cards - * global definitions and exported vars and functions. - * - * Author Werner Cornelius (werner@titro.de) for Hypercope GmbH - * Copyright 1999 by Werner Cornelius (werner@titro.de) - * - * This software may be used and distributed according to the terms - * of the GNU General Public License, incorporated herein by reference. - * - */ - -#ifndef HYSDN_DEFS_H -#define HYSDN_DEFS_H - -#include <linux/hysdn_if.h> -#include <linux/interrupt.h> -#include <linux/workqueue.h> -#include <linux/skbuff.h> - -#include "ince1pc.h" - -#ifdef CONFIG_HYSDN_CAPI -#include <linux/capi.h> -#include <linux/isdn/capicmd.h> -#include <linux/isdn/capiutil.h> -#include <linux/isdn/capilli.h> - -/***************************/ -/* CAPI-Profile values. */ -/***************************/ - -#define GLOBAL_OPTION_INTERNAL_CONTROLLER 0x0001 -#define GLOBAL_OPTION_EXTERNAL_CONTROLLER 0x0002 -#define GLOBAL_OPTION_HANDSET 0x0004 -#define GLOBAL_OPTION_DTMF 0x0008 -#define GLOBAL_OPTION_SUPPL_SERVICES 0x0010 -#define GLOBAL_OPTION_CHANNEL_ALLOCATION 0x0020 -#define GLOBAL_OPTION_B_CHANNEL_OPERATION 0x0040 - -#define B1_PROT_64KBIT_HDLC 0x0001 -#define B1_PROT_64KBIT_TRANSPARENT 0x0002 -#define B1_PROT_V110_ASYNCH 0x0004 -#define B1_PROT_V110_SYNCH 0x0008 -#define B1_PROT_T30 0x0010 -#define B1_PROT_64KBIT_INV_HDLC 0x0020 -#define B1_PROT_56KBIT_TRANSPARENT 0x0040 - -#define B2_PROT_ISO7776 0x0001 -#define B2_PROT_TRANSPARENT 0x0002 -#define B2_PROT_SDLC 0x0004 -#define B2_PROT_LAPD 0x0008 -#define B2_PROT_T30 0x0010 -#define B2_PROT_PPP 0x0020 -#define B2_PROT_TRANSPARENT_IGNORE_B1_FRAMING_ERRORS 0x0040 - -#define B3_PROT_TRANSPARENT 0x0001 -#define B3_PROT_T90NL 0x0002 -#define B3_PROT_ISO8208 0x0004 -#define B3_PROT_X25_DCE 0x0008 -#define B3_PROT_T30 0x0010 -#define B3_PROT_T30EXT 0x0020 - -#define HYSDN_MAXVERSION 8 - -/* Number of sendbuffers in CAPI-queue */ -#define HYSDN_MAX_CAPI_SKB 20 - -#endif /* CONFIG_HYSDN_CAPI*/ - -/************************************************/ -/* constants and bits for debugging/log outputs */ -/************************************************/ -#define LOG_MAX_LINELEN 120 -#define DEB_OUT_SYSLOG 0x80000000 /* output to syslog instead of proc fs */ -#define LOG_MEM_ERR 0x00000001 /* log memory errors like kmalloc failure */ -#define LOG_POF_OPEN 0x00000010 /* log pof open and close activities */ -#define LOG_POF_RECORD 0x00000020 /* log pof record parser */ -#define LOG_POF_WRITE 0x00000040 /* log detailed pof write operation */ -#define LOG_POF_CARD 0x00000080 /* log pof related card functions */ -#define LOG_CNF_LINE 0x00000100 /* all conf lines are put to procfs */ -#define LOG_CNF_DATA 0x00000200 /* non comment conf lines are shown with channel */ -#define LOG_CNF_MISC 0x00000400 /* additional conf line debug outputs */ -#define LOG_SCHED_ASYN 0x00001000 /* debug schedulers async tx routines */ -#define LOG_PROC_OPEN 0x00100000 /* open and close from procfs are logged */ -#define LOG_PROC_ALL 0x00200000 /* all actions from procfs are logged */ -#define LOG_NET_INIT 0x00010000 /* network init and deinit logging */ - -#define DEF_DEB_FLAGS 0x7fff000f /* everything is logged to procfs */ - -/**********************************/ -/* proc filesystem name constants */ -/**********************************/ -#define PROC_SUBDIR_NAME "hysdn" -#define PROC_CONF_BASENAME "cardconf" -#define PROC_LOG_BASENAME "cardlog" - -/***********************************/ -/* PCI 32 bit parms for IO and MEM */ -/***********************************/ -#define PCI_REG_PLX_MEM_BASE 0 -#define PCI_REG_PLX_IO_BASE 1 -#define PCI_REG_MEMORY_BASE 3 - -/**************/ -/* card types */ -/**************/ -#define BD_NONE 0U -#define BD_PERFORMANCE 1U -#define BD_VALUE 2U -#define BD_PCCARD 3U -#define BD_ERGO 4U -#define BD_METRO 5U -#define BD_CHAMP2 6U -#define BD_PLEXUS 7U - -/******************************************************/ -/* defined states for cards shown by reading cardconf */ -/******************************************************/ -#define CARD_STATE_UNUSED 0 /* never been used or booted */ -#define CARD_STATE_BOOTING 1 /* booting is in progress */ -#define CARD_STATE_BOOTERR 2 /* a previous boot was aborted */ -#define CARD_STATE_RUN 3 /* card is active */ - -/*******************************/ -/* defines for error_log_state */ -/*******************************/ -#define ERRLOG_STATE_OFF 0 /* error log is switched off, nothing to do */ -#define ERRLOG_STATE_ON 1 /* error log is switched on, wait for data */ -#define ERRLOG_STATE_START 2 /* start error logging */ -#define ERRLOG_STATE_STOP 3 /* stop error logging */ - -/*******************************/ -/* data structure for one card */ -/*******************************/ -typedef struct HYSDN_CARD { - - /* general variables for the cards */ - int myid; /* own driver card id */ - unsigned char bus; /* pci bus the card is connected to */ - unsigned char devfn; /* slot+function bit encoded */ - unsigned short subsysid;/* PCI subsystem id */ - unsigned char brdtype; /* type of card */ - unsigned int bchans; /* number of available B-channels */ - unsigned int faxchans; /* number of available fax-channels */ - unsigned char mac_addr[6];/* MAC Address read from card */ - unsigned int irq; /* interrupt number */ - unsigned int iobase; /* IO-port base address */ - unsigned long plxbase; /* PLX memory base */ - unsigned long membase; /* DPRAM memory base */ - unsigned long memend; /* DPRAM memory end */ - void *dpram; /* mapped dpram */ - int state; /* actual state of card -> CARD_STATE_** */ - struct HYSDN_CARD *next; /* pointer to next card */ - - /* data areas for the /proc file system */ - void *proclog; /* pointer to proclog filesystem specific data */ - void *procconf; /* pointer to procconf filesystem specific data */ - - /* debugging and logging */ - unsigned char err_log_state;/* actual error log state of the card */ - unsigned long debug_flags;/* tells what should be debugged and where */ - void (*set_errlog_state) (struct HYSDN_CARD *, int); - - /* interrupt handler + interrupt synchronisation */ - struct work_struct irq_queue; /* interrupt task queue */ - unsigned char volatile irq_enabled;/* interrupt enabled if != 0 */ - unsigned char volatile hw_lock;/* hardware is currently locked -> no access */ - - /* boot process */ - void *boot; /* pointer to boot private data */ - int (*writebootimg) (struct HYSDN_CARD *, unsigned char *, unsigned long); - int (*writebootseq) (struct HYSDN_CARD *, unsigned char *, int); - int (*waitpofready) (struct HYSDN_CARD *); - int (*testram) (struct HYSDN_CARD *); - - /* scheduler for data transfer (only async parts) */ - unsigned char async_data[256];/* async data to be sent (normally for config) */ - unsigned short volatile async_len;/* length of data to sent */ - unsigned short volatile async_channel;/* channel number for async transfer */ - int volatile async_busy; /* flag != 0 sending in progress */ - int volatile net_tx_busy; /* a network packet tx is in progress */ - - /* network interface */ - void *netif; /* pointer to network structure */ - - /* init and deinit stopcard for booting, too */ - void (*stopcard) (struct HYSDN_CARD *); - void (*releasehardware) (struct HYSDN_CARD *); - - spinlock_t hysdn_lock; -#ifdef CONFIG_HYSDN_CAPI - struct hycapictrl_info { - char cardname[32]; - spinlock_t lock; - int versionlen; - char versionbuf[1024]; - char *version[HYSDN_MAXVERSION]; - - char infobuf[128]; /* for function procinfo */ - - struct HYSDN_CARD *card; - struct capi_ctr capi_ctrl; - struct sk_buff *skbs[HYSDN_MAX_CAPI_SKB]; - int in_idx, out_idx; /* indexes to buffer ring */ - int sk_count; /* number of buffers currently in ring */ - struct sk_buff *tx_skb; /* buffer for tx operation */ - - struct list_head ncci_head; - } *hyctrlinfo; -#endif /* CONFIG_HYSDN_CAPI */ -} hysdn_card; - -#ifdef CONFIG_HYSDN_CAPI -typedef struct hycapictrl_info hycapictrl_info; -#endif /* CONFIG_HYSDN_CAPI */ - - -/*****************/ -/* exported vars */ -/*****************/ -extern hysdn_card *card_root; /* pointer to first card */ - - - -/*************************/ -/* im/exported functions */ -/*************************/ - -/* hysdn_procconf.c */ -extern int hysdn_procconf_init(void); /* init proc config filesys */ -extern void hysdn_procconf_release(void); /* deinit proc config filesys */ - -/* hysdn_proclog.c */ -extern int hysdn_proclog_init(hysdn_card *); /* init proc log entry */ -extern void hysdn_proclog_release(hysdn_card *); /* deinit proc log entry */ -extern void hysdn_addlog(hysdn_card *, char *, ...); /* output data to log */ -extern void hysdn_card_errlog(hysdn_card *, tErrLogEntry *, int); /* output card log */ - -/* boardergo.c */ -extern int ergo_inithardware(hysdn_card *card); /* get hardware -> module init */ - -/* hysdn_boot.c */ -extern int pof_write_close(hysdn_card *); /* close proc file after writing pof */ -extern int pof_write_open(hysdn_card *, unsigned char **); /* open proc file for writing pof */ -extern int pof_write_buffer(hysdn_card *, int); /* write boot data to card */ -extern int EvalSysrTokData(hysdn_card *, unsigned char *, int); /* Check Sysready Token Data */ - -/* hysdn_sched.c */ -extern int hysdn_sched_tx(hysdn_card *, unsigned char *, - unsigned short volatile *, unsigned short volatile *, - unsigned short); -extern int hysdn_sched_rx(hysdn_card *, unsigned char *, unsigned short, - unsigned short); -extern int hysdn_tx_cfgline(hysdn_card *, unsigned char *, - unsigned short); /* send one cfg line */ - -/* hysdn_net.c */ -extern unsigned int hynet_enable; -extern int hysdn_net_create(hysdn_card *); /* create a new net device */ -extern int hysdn_net_release(hysdn_card *); /* delete the device */ -extern char *hysdn_net_getname(hysdn_card *); /* get name of net interface */ -extern void hysdn_tx_netack(hysdn_card *); /* acknowledge a packet tx */ -extern struct sk_buff *hysdn_tx_netget(hysdn_card *); /* get next network packet */ -extern void hysdn_rx_netpkt(hysdn_card *, unsigned char *, - unsigned short); /* rxed packet from network */ - -#ifdef CONFIG_HYSDN_CAPI -extern unsigned int hycapi_enable; -extern int hycapi_capi_create(hysdn_card *); /* create a new capi device */ -extern int hycapi_capi_release(hysdn_card *); /* delete the device */ -extern int hycapi_capi_stop(hysdn_card *card); /* suspend */ -extern void hycapi_rx_capipkt(hysdn_card *card, unsigned char *buf, - unsigned short len); -extern void hycapi_tx_capiack(hysdn_card *card); -extern struct sk_buff *hycapi_tx_capiget(hysdn_card *card); -extern int hycapi_init(void); -extern void hycapi_cleanup(void); -#endif /* CONFIG_HYSDN_CAPI */ - -#endif /* HYSDN_DEFS_H */ diff --git a/drivers/staging/isdn/hysdn/hysdn_init.c b/drivers/staging/isdn/hysdn/hysdn_init.c deleted file mode 100644 index 0db2f7506250..000000000000 --- a/drivers/staging/isdn/hysdn/hysdn_init.c +++ /dev/null @@ -1,213 +0,0 @@ -/* $Id: hysdn_init.c,v 1.6.6.6 2001/09/23 22:24:54 kai Exp $ - * - * Linux driver for HYSDN cards, init functions. - * - * Author Werner Cornelius (werner@titro.de) for Hypercope GmbH - * Copyright 1999 by Werner Cornelius (werner@titro.de) - * - * This software may be used and distributed according to the terms - * of the GNU General Public License, incorporated herein by reference. - * - */ - -#include <linux/module.h> -#include <linux/init.h> -#include <linux/poll.h> -#include <linux/vmalloc.h> -#include <linux/slab.h> -#include <linux/pci.h> - -#include "hysdn_defs.h" - -static struct pci_device_id hysdn_pci_tbl[] = { - { PCI_VENDOR_ID_HYPERCOPE, PCI_DEVICE_ID_HYPERCOPE_PLX, - PCI_ANY_ID, PCI_SUBDEVICE_ID_HYPERCOPE_METRO, 0, 0, BD_METRO }, - { PCI_VENDOR_ID_HYPERCOPE, PCI_DEVICE_ID_HYPERCOPE_PLX, - PCI_ANY_ID, PCI_SUBDEVICE_ID_HYPERCOPE_CHAMP2, 0, 0, BD_CHAMP2 }, - { PCI_VENDOR_ID_HYPERCOPE, PCI_DEVICE_ID_HYPERCOPE_PLX, - PCI_ANY_ID, PCI_SUBDEVICE_ID_HYPERCOPE_ERGO, 0, 0, BD_ERGO }, - { PCI_VENDOR_ID_HYPERCOPE, PCI_DEVICE_ID_HYPERCOPE_PLX, - PCI_ANY_ID, PCI_SUBDEVICE_ID_HYPERCOPE_OLD_ERGO, 0, 0, BD_ERGO }, - - { } /* Terminating entry */ -}; -MODULE_DEVICE_TABLE(pci, hysdn_pci_tbl); -MODULE_DESCRIPTION("ISDN4Linux: Driver for HYSDN cards"); -MODULE_AUTHOR("Werner Cornelius"); -MODULE_LICENSE("GPL"); - -static int cardmax; /* number of found cards */ -hysdn_card *card_root = NULL; /* pointer to first card */ -static hysdn_card *card_last = NULL; /* pointer to first card */ - - -/****************************************************************************/ -/* The module startup and shutdown code. Only compiled when used as module. */ -/* Using the driver as module is always advisable, because the booting */ -/* image becomes smaller and the driver code is only loaded when needed. */ -/* Additionally newer versions may be activated without rebooting. */ -/****************************************************************************/ - -/****************************************************************************/ -/* init_module is called once when the module is loaded to do all necessary */ -/* things like autodetect... */ -/* If the return value of this function is 0 the init has been successful */ -/* and the module is added to the list in /proc/modules, otherwise an error */ -/* is assumed and the module will not be kept in memory. */ -/****************************************************************************/ - -static int hysdn_pci_init_one(struct pci_dev *akt_pcidev, - const struct pci_device_id *ent) -{ - hysdn_card *card; - int rc; - - rc = pci_enable_device(akt_pcidev); - if (rc) - return rc; - - if (!(card = kzalloc(sizeof(hysdn_card), GFP_KERNEL))) { - printk(KERN_ERR "HYSDN: unable to alloc device mem \n"); - rc = -ENOMEM; - goto err_out; - } - card->myid = cardmax; /* set own id */ - card->bus = akt_pcidev->bus->number; - card->devfn = akt_pcidev->devfn; /* slot + function */ - card->subsysid = akt_pcidev->subsystem_device; - card->irq = akt_pcidev->irq; - card->iobase = pci_resource_start(akt_pcidev, PCI_REG_PLX_IO_BASE); - card->plxbase = pci_resource_start(akt_pcidev, PCI_REG_PLX_MEM_BASE); - card->membase = pci_resource_start(akt_pcidev, PCI_REG_MEMORY_BASE); - card->brdtype = BD_NONE; /* unknown */ - card->debug_flags = DEF_DEB_FLAGS; /* set default debug */ - card->faxchans = 0; /* default no fax channels */ - card->bchans = 2; /* and 2 b-channels */ - card->brdtype = ent->driver_data; - - if (ergo_inithardware(card)) { - printk(KERN_WARNING "HYSDN: card at io 0x%04x already in use\n", card->iobase); - rc = -EBUSY; - goto err_out_card; - } - - cardmax++; - card->next = NULL; /*end of chain */ - if (card_last) - card_last->next = card; /* pointer to next card */ - else - card_root = card; - card_last = card; /* new chain end */ - - pci_set_drvdata(akt_pcidev, card); - return 0; - -err_out_card: - kfree(card); -err_out: - pci_disable_device(akt_pcidev); - return rc; -} - -static void hysdn_pci_remove_one(struct pci_dev *akt_pcidev) -{ - hysdn_card *card = pci_get_drvdata(akt_pcidev); - - pci_set_drvdata(akt_pcidev, NULL); - - if (card->stopcard) - card->stopcard(card); - -#ifdef CONFIG_HYSDN_CAPI - hycapi_capi_release(card); -#endif - - if (card->releasehardware) - card->releasehardware(card); /* free all hardware resources */ - - if (card == card_root) { - card_root = card_root->next; - if (!card_root) - card_last = NULL; - } else { - hysdn_card *tmp = card_root; - while (tmp) { - if (tmp->next == card) - tmp->next = card->next; - card_last = tmp; - tmp = tmp->next; - } - } - - kfree(card); - pci_disable_device(akt_pcidev); -} - -static struct pci_driver hysdn_pci_driver = { - .name = "hysdn", - .id_table = hysdn_pci_tbl, - .probe = hysdn_pci_init_one, - .remove = hysdn_pci_remove_one, -}; - -static int hysdn_have_procfs; - -static int __init -hysdn_init(void) -{ - int rc; - - printk(KERN_NOTICE "HYSDN: module loaded\n"); - - rc = pci_register_driver(&hysdn_pci_driver); - if (rc) - return rc; - - printk(KERN_INFO "HYSDN: %d card(s) found.\n", cardmax); - - if (!hysdn_procconf_init()) - hysdn_have_procfs = 1; - -#ifdef CONFIG_HYSDN_CAPI - if (cardmax > 0) { - if (hycapi_init()) { - printk(KERN_ERR "HYCAPI: init failed\n"); - - if (hysdn_have_procfs) - hysdn_procconf_release(); - - pci_unregister_driver(&hysdn_pci_driver); - return -ESPIPE; - } - } -#endif /* CONFIG_HYSDN_CAPI */ - - return 0; /* no error */ -} /* init_module */ - - -/***********************************************************************/ -/* cleanup_module is called when the module is released by the kernel. */ -/* The routine is only called if init_module has been successful and */ -/* the module counter has a value of 0. Otherwise this function will */ -/* not be called. This function must release all resources still allo- */ -/* cated as after the return from this function the module code will */ -/* be removed from memory. */ -/***********************************************************************/ -static void __exit -hysdn_exit(void) -{ - if (hysdn_have_procfs) - hysdn_procconf_release(); - - pci_unregister_driver(&hysdn_pci_driver); - -#ifdef CONFIG_HYSDN_CAPI - hycapi_cleanup(); -#endif /* CONFIG_HYSDN_CAPI */ - - printk(KERN_NOTICE "HYSDN: module unloaded\n"); -} /* cleanup_module */ - -module_init(hysdn_init); -module_exit(hysdn_exit); diff --git a/drivers/staging/isdn/hysdn/hysdn_net.c b/drivers/staging/isdn/hysdn/hysdn_net.c deleted file mode 100644 index dcb9ef7a2651..000000000000 --- a/drivers/staging/isdn/hysdn/hysdn_net.c +++ /dev/null @@ -1,330 +0,0 @@ -/* $Id: hysdn_net.c,v 1.8.6.4 2001/09/23 22:24:54 kai Exp $ - * - * Linux driver for HYSDN cards, net (ethernet type) handling routines. - * - * Author Werner Cornelius (werner@titro.de) for Hypercope GmbH - * Copyright 1999 by Werner Cornelius (werner@titro.de) - * - * This software may be used and distributed according to the terms - * of the GNU General Public License, incorporated herein by reference. - * - * This net module has been inspired by the skeleton driver from - * Donald Becker (becker@CESDIS.gsfc.nasa.gov) - * - */ - -#include <linux/module.h> -#include <linux/signal.h> -#include <linux/kernel.h> -#include <linux/netdevice.h> -#include <linux/etherdevice.h> -#include <linux/skbuff.h> -#include <linux/inetdevice.h> - -#include "hysdn_defs.h" - -unsigned int hynet_enable = 0xffffffff; -module_param(hynet_enable, uint, 0); - -#define MAX_SKB_BUFFERS 20 /* number of buffers for keeping TX-data */ - -/****************************************************************************/ -/* structure containing the complete network data. The structure is aligned */ -/* in a way that both, the device and statistics are kept inside it. */ -/* for proper access, the device structure MUST be the first var/struct */ -/* inside the definition. */ -/****************************************************************************/ -struct net_local { - /* Tx control lock. This protects the transmit buffer ring - * state along with the "tx full" state of the driver. This - * means all netif_queue flow control actions are protected - * by this lock as well. - */ - struct net_device *dev; - spinlock_t lock; - struct sk_buff *skbs[MAX_SKB_BUFFERS]; /* pointers to tx-skbs */ - int in_idx, out_idx; /* indexes to buffer ring */ - int sk_count; /* number of buffers currently in ring */ -}; /* net_local */ - - - -/*********************************************************************/ -/* Open/initialize the board. This is called (in the current kernel) */ -/* sometime after booting when the 'ifconfig' program is run. */ -/* This routine should set everything up anew at each open, even */ -/* registers that "should" only need to be set once at boot, so that */ -/* there is non-reboot way to recover if something goes wrong. */ -/*********************************************************************/ -static int -net_open(struct net_device *dev) -{ - struct in_device *in_dev; - hysdn_card *card = dev->ml_priv; - int i; - - netif_start_queue(dev); /* start tx-queueing */ - - /* Fill in the MAC-level header (if not already set) */ - if (!card->mac_addr[0]) { - for (i = 0; i < ETH_ALEN; i++) - dev->dev_addr[i] = 0xfc; - if ((in_dev = dev->ip_ptr) != NULL) { - const struct in_ifaddr *ifa; - - rcu_read_lock(); - ifa = rcu_dereference(in_dev->ifa_list); - if (ifa != NULL) - memcpy(dev->dev_addr + (ETH_ALEN - sizeof(ifa->ifa_local)), &ifa->ifa_local, sizeof(ifa->ifa_local)); - rcu_read_unlock(); - } - } else - memcpy(dev->dev_addr, card->mac_addr, ETH_ALEN); - - return (0); -} /* net_open */ - -/*******************************************/ -/* flush the currently occupied tx-buffers */ -/* must only be called when device closed */ -/*******************************************/ -static void -flush_tx_buffers(struct net_local *nl) -{ - - while (nl->sk_count) { - dev_kfree_skb(nl->skbs[nl->out_idx++]); /* free skb */ - if (nl->out_idx >= MAX_SKB_BUFFERS) - nl->out_idx = 0; /* wrap around */ - nl->sk_count--; - } -} /* flush_tx_buffers */ - - -/*********************************************************************/ -/* close/decativate the device. The device is not removed, but only */ -/* deactivated. */ -/*********************************************************************/ -static int -net_close(struct net_device *dev) -{ - - netif_stop_queue(dev); /* disable queueing */ - - flush_tx_buffers((struct net_local *) dev); - - return (0); /* success */ -} /* net_close */ - -/************************************/ -/* send a packet on this interface. */ -/* new style for kernel >= 2.3.33 */ -/************************************/ -static netdev_tx_t -net_send_packet(struct sk_buff *skb, struct net_device *dev) -{ - struct net_local *lp = (struct net_local *) dev; - - spin_lock_irq(&lp->lock); - - lp->skbs[lp->in_idx++] = skb; /* add to buffer list */ - if (lp->in_idx >= MAX_SKB_BUFFERS) - lp->in_idx = 0; /* wrap around */ - lp->sk_count++; /* adjust counter */ - netif_trans_update(dev); - - /* If we just used up the very last entry in the - * TX ring on this device, tell the queueing - * layer to send no more. - */ - if (lp->sk_count >= MAX_SKB_BUFFERS) - netif_stop_queue(dev); - - /* When the TX completion hw interrupt arrives, this - * is when the transmit statistics are updated. - */ - - spin_unlock_irq(&lp->lock); - - if (lp->sk_count <= 3) { - schedule_work(&((hysdn_card *) dev->ml_priv)->irq_queue); - } - return NETDEV_TX_OK; /* success */ -} /* net_send_packet */ - - - -/***********************************************************************/ -/* acknowlegde a packet send. The network layer will be informed about */ -/* completion */ -/***********************************************************************/ -void -hysdn_tx_netack(hysdn_card *card) -{ - struct net_local *lp = card->netif; - - if (!lp) - return; /* non existing device */ - - - if (!lp->sk_count) - return; /* error condition */ - - lp->dev->stats.tx_packets++; - lp->dev->stats.tx_bytes += lp->skbs[lp->out_idx]->len; - - dev_kfree_skb(lp->skbs[lp->out_idx++]); /* free skb */ - if (lp->out_idx >= MAX_SKB_BUFFERS) - lp->out_idx = 0; /* wrap around */ - - if (lp->sk_count-- == MAX_SKB_BUFFERS) /* dec usage count */ - netif_start_queue((struct net_device *) lp); -} /* hysdn_tx_netack */ - -/*****************************************************/ -/* we got a packet from the network, go and queue it */ -/*****************************************************/ -void -hysdn_rx_netpkt(hysdn_card *card, unsigned char *buf, unsigned short len) -{ - struct net_local *lp = card->netif; - struct net_device *dev; - struct sk_buff *skb; - - if (!lp) - return; /* non existing device */ - - dev = lp->dev; - dev->stats.rx_bytes += len; - - skb = dev_alloc_skb(len); - if (skb == NULL) { - printk(KERN_NOTICE "%s: Memory squeeze, dropping packet.\n", - dev->name); - dev->stats.rx_dropped++; - return; - } - /* copy the data */ - skb_put_data(skb, buf, len); - - /* determine the used protocol */ - skb->protocol = eth_type_trans(skb, dev); - - dev->stats.rx_packets++; /* adjust packet count */ - - netif_rx(skb); -} /* hysdn_rx_netpkt */ - -/*****************************************************/ -/* return the pointer to a network packet to be send */ -/*****************************************************/ -struct sk_buff * -hysdn_tx_netget(hysdn_card *card) -{ - struct net_local *lp = card->netif; - - if (!lp) - return (NULL); /* non existing device */ - - if (!lp->sk_count) - return (NULL); /* nothing available */ - - return (lp->skbs[lp->out_idx]); /* next packet to send */ -} /* hysdn_tx_netget */ - -static const struct net_device_ops hysdn_netdev_ops = { - .ndo_open = net_open, - .ndo_stop = net_close, - .ndo_start_xmit = net_send_packet, - .ndo_set_mac_address = eth_mac_addr, - .ndo_validate_addr = eth_validate_addr, -}; - - -/*****************************************************************************/ -/* hysdn_net_create creates a new net device for the given card. If a device */ -/* already exists, it will be deleted and created a new one. The return value */ -/* 0 announces success, else a negative error code will be returned. */ -/*****************************************************************************/ -int -hysdn_net_create(hysdn_card *card) -{ - struct net_device *dev; - int i; - struct net_local *lp; - - if (!card) { - printk(KERN_WARNING "No card-pt in hysdn_net_create!\n"); - return (-ENOMEM); - } - hysdn_net_release(card); /* release an existing net device */ - - dev = alloc_etherdev(sizeof(struct net_local)); - if (!dev) { - printk(KERN_WARNING "HYSDN: unable to allocate mem\n"); - return (-ENOMEM); - } - - lp = netdev_priv(dev); - lp->dev = dev; - - dev->netdev_ops = &hysdn_netdev_ops; - spin_lock_init(&((struct net_local *) dev)->lock); - - /* initialise necessary or informing fields */ - dev->base_addr = card->iobase; /* IO address */ - dev->irq = card->irq; /* irq */ - - dev->netdev_ops = &hysdn_netdev_ops; - if ((i = register_netdev(dev))) { - printk(KERN_WARNING "HYSDN: unable to create network device\n"); - free_netdev(dev); - return (i); - } - dev->ml_priv = card; /* remember pointer to own data structure */ - card->netif = dev; /* setup the local pointer */ - - if (card->debug_flags & LOG_NET_INIT) - hysdn_addlog(card, "network device created"); - return 0; /* and return success */ -} /* hysdn_net_create */ - -/***************************************************************************/ -/* hysdn_net_release deletes the net device for the given card. The return */ -/* value 0 announces success, else a negative error code will be returned. */ -/***************************************************************************/ -int -hysdn_net_release(hysdn_card *card) -{ - struct net_device *dev = card->netif; - - if (!dev) - return (0); /* non existing */ - - card->netif = NULL; /* clear out pointer */ - net_close(dev); - - flush_tx_buffers((struct net_local *) dev); /* empty buffers */ - - unregister_netdev(dev); /* release the device */ - free_netdev(dev); /* release the memory allocated */ - if (card->debug_flags & LOG_NET_INIT) - hysdn_addlog(card, "network device deleted"); - - return (0); /* always successful */ -} /* hysdn_net_release */ - -/*****************************************************************************/ -/* hysdn_net_getname returns a pointer to the name of the network interface. */ -/* if the interface is not existing, a "-" is returned. */ -/*****************************************************************************/ -char * -hysdn_net_getname(hysdn_card *card) -{ - struct net_device *dev = card->netif; - - if (!dev) - return ("-"); /* non existing */ - - return (dev->name); -} /* hysdn_net_getname */ diff --git a/drivers/staging/isdn/hysdn/hysdn_pof.h b/drivers/staging/isdn/hysdn/hysdn_pof.h deleted file mode 100644 index f63f5fa59d7e..000000000000 --- a/drivers/staging/isdn/hysdn/hysdn_pof.h +++ /dev/null @@ -1,78 +0,0 @@ -/* $Id: hysdn_pof.h,v 1.2.6.1 2001/09/23 22:24:54 kai Exp $ - * - * Linux driver for HYSDN cards, definitions used for handling pof-files. - * - * Author Werner Cornelius (werner@titro.de) for Hypercope GmbH - * Copyright 1999 by Werner Cornelius (werner@titro.de) - * - * This software may be used and distributed according to the terms - * of the GNU General Public License, incorporated herein by reference. - * - */ - -/************************/ -/* POF specific defines */ -/************************/ -#define BOOT_BUF_SIZE 0x1000 /* =4096, maybe moved to other h file */ -#define CRYPT_FEEDTERM 0x8142 -#define CRYPT_STARTTERM 0x81a5 -/* max. timeout time in seconds - * from end of booting to POF is ready - */ -#define POF_READY_TIME_OUT_SEC 10 - -/**********************************/ -/* defines for 1.stage boot image */ -/**********************************/ - -/* the POF file record containing the boot loader image - * has 2 pages a 16KB: - * 1. page contains the high 16-bit part of the 32-bit E1 words - * 2. page contains the low 16-bit part of the 32-bit E1 words - * - * In each 16KB page we assume the start of the boot loader code - * in the highest 2KB part (at offset 0x3800); - * the rest (0x0000..0x37FF) is assumed to contain 0 bytes. - */ - -#define POF_BOOT_LOADER_PAGE_SIZE 0x4000 /* =16384U */ -#define POF_BOOT_LOADER_TOTAL_SIZE (2U * POF_BOOT_LOADER_PAGE_SIZE) - -#define POF_BOOT_LOADER_CODE_SIZE 0x0800 /* =2KB =2048U */ - -/* offset in boot page, where loader code may start */ -/* =0x3800= 14336U */ -#define POF_BOOT_LOADER_OFF_IN_PAGE (POF_BOOT_LOADER_PAGE_SIZE-POF_BOOT_LOADER_CODE_SIZE) - - -/*--------------------------------------POF file record structs------------*/ -typedef struct PofFileHdr_tag { /* Pof file header */ - /*00 */ unsigned long Magic __attribute__((packed)); - /*04 */ unsigned long N_PofRecs __attribute__((packed)); -/*08 */ -} tPofFileHdr; - -typedef struct PofRecHdr_tag { /* Pof record header */ - /*00 */ unsigned short PofRecId __attribute__((packed)); - /*02 */ unsigned long PofRecDataLen __attribute__((packed)); -/*06 */ -} tPofRecHdr; - -typedef struct PofTimeStamp_tag { - /*00 */ unsigned long UnixTime __attribute__((packed)); - /*04 */ unsigned char DateTimeText[0x28]; - /* =40 */ -/*2C */ -} tPofTimeStamp; - -/* tPofFileHdr.Magic value: */ -#define TAGFILEMAGIC 0x464F501AUL -/* tPofRecHdr.PofRecId values: */ -#define TAG_ABSDATA 0x1000 /* abs. data */ -#define TAG_BOOTDTA 0x1001 /* boot data */ -#define TAG_COMMENT 0x0020 -#define TAG_SYSCALL 0x0021 -#define TAG_FLOWCTRL 0x0022 -#define TAG_TIMESTMP 0x0010 /* date/time stamp of version */ -#define TAG_CABSDATA 0x1100 /* crypted abs. data */ -#define TAG_CBOOTDTA 0x1101 /* crypted boot data */ diff --git a/drivers/staging/isdn/hysdn/hysdn_procconf.c b/drivers/staging/isdn/hysdn/hysdn_procconf.c deleted file mode 100644 index 48afd9f5316e..000000000000 --- a/drivers/staging/isdn/hysdn/hysdn_procconf.c +++ /dev/null @@ -1,411 +0,0 @@ -/* $Id: hysdn_procconf.c,v 1.8.6.4 2001/09/23 22:24:54 kai Exp $ - * - * Linux driver for HYSDN cards, /proc/net filesystem dir and conf functions. - * - * written by Werner Cornelius (werner@titro.de) for Hypercope GmbH - * - * Copyright 1999 by Werner Cornelius (werner@titro.de) - * - * This software may be used and distributed according to the terms - * of the GNU General Public License, incorporated herein by reference. - * - */ - -#include <linux/cred.h> -#include <linux/module.h> -#include <linux/poll.h> -#include <linux/proc_fs.h> -#include <linux/pci.h> -#include <linux/slab.h> -#include <linux/mutex.h> -#include <net/net_namespace.h> - -#include "hysdn_defs.h" - -static DEFINE_MUTEX(hysdn_conf_mutex); - -#define INFO_OUT_LEN 80 /* length of info line including lf */ - -/********************************************************/ -/* defines and data structure for conf write operations */ -/********************************************************/ -#define CONF_STATE_DETECT 0 /* waiting for detect */ -#define CONF_STATE_CONF 1 /* writing config data */ -#define CONF_STATE_POF 2 /* writing pof data */ -#define CONF_LINE_LEN 255 /* 255 chars max */ - -struct conf_writedata { - hysdn_card *card; /* card the device is connected to */ - int buf_size; /* actual number of bytes in the buffer */ - int needed_size; /* needed size when reading pof */ - int state; /* actual interface states from above constants */ - unsigned char conf_line[CONF_LINE_LEN]; /* buffered conf line */ - unsigned short channel; /* active channel number */ - unsigned char *pof_buffer; /* buffer when writing pof */ -}; - -/***********************************************************************/ -/* process_line parses one config line and transfers it to the card if */ -/* necessary. */ -/* if the return value is negative an error occurred. */ -/***********************************************************************/ -static int -process_line(struct conf_writedata *cnf) -{ - unsigned char *cp = cnf->conf_line; - int i; - - if (cnf->card->debug_flags & LOG_CNF_LINE) - hysdn_addlog(cnf->card, "conf line: %s", cp); - - if (*cp == '-') { /* option */ - cp++; /* point to option char */ - - if (*cp++ != 'c') - return (0); /* option unknown or used */ - i = 0; /* start value for channel */ - while ((*cp <= '9') && (*cp >= '0')) - i = i * 10 + *cp++ - '0'; /* get decimal number */ - if (i > 65535) { - if (cnf->card->debug_flags & LOG_CNF_MISC) - hysdn_addlog(cnf->card, "conf channel invalid %d", i); - return (-ERR_INV_CHAN); /* invalid channel */ - } - cnf->channel = i & 0xFFFF; /* set new channel number */ - return (0); /* success */ - } /* option */ - if (*cp == '*') { /* line to send */ - if (cnf->card->debug_flags & LOG_CNF_DATA) - hysdn_addlog(cnf->card, "conf chan=%d %s", cnf->channel, cp); - return (hysdn_tx_cfgline(cnf->card, cnf->conf_line + 1, - cnf->channel)); /* send the line without * */ - } /* line to send */ - return (0); -} /* process_line */ - -/***********************************/ -/* conf file operations and tables */ -/***********************************/ - -/****************************************************/ -/* write conf file -> boot or send cfg line to card */ -/****************************************************/ -static ssize_t -hysdn_conf_write(struct file *file, const char __user *buf, size_t count, loff_t *off) -{ - struct conf_writedata *cnf; - int i; - unsigned char ch, *cp; - - if (!count) - return (0); /* nothing to handle */ - - if (!(cnf = file->private_data)) - return (-EFAULT); /* should never happen */ - - if (cnf->state == CONF_STATE_DETECT) { /* auto detect cnf or pof data */ - if (copy_from_user(&ch, buf, 1)) /* get first char for detect */ - return (-EFAULT); - - if (ch == 0x1A) { - /* we detected a pof file */ - if ((cnf->needed_size = pof_write_open(cnf->card, &cnf->pof_buffer)) <= 0) - return (cnf->needed_size); /* an error occurred -> exit */ - cnf->buf_size = 0; /* buffer is empty */ - cnf->state = CONF_STATE_POF; /* new state */ - } else { - /* conf data has been detected */ - cnf->buf_size = 0; /* buffer is empty */ - cnf->state = CONF_STATE_CONF; /* requested conf data write */ - if (cnf->card->state != CARD_STATE_RUN) - return (-ERR_NOT_BOOTED); - cnf->conf_line[CONF_LINE_LEN - 1] = 0; /* limit string length */ - cnf->channel = 4098; /* default channel for output */ - } - } /* state was auto detect */ - if (cnf->state == CONF_STATE_POF) { /* pof write active */ - i = cnf->needed_size - cnf->buf_size; /* bytes still missing for write */ - if (i <= 0) - return (-EINVAL); /* size error handling pof */ - - if (i < count) - count = i; /* limit requested number of bytes */ - if (copy_from_user(cnf->pof_buffer + cnf->buf_size, buf, count)) - return (-EFAULT); /* error while copying */ - cnf->buf_size += count; - - if (cnf->needed_size == cnf->buf_size) { - cnf->needed_size = pof_write_buffer(cnf->card, cnf->buf_size); /* write data */ - if (cnf->needed_size <= 0) { - cnf->card->state = CARD_STATE_BOOTERR; /* show boot error */ - return (cnf->needed_size); /* an error occurred */ - } - cnf->buf_size = 0; /* buffer is empty again */ - } - } - /* pof write active */ - else { /* conf write active */ - - if (cnf->card->state != CARD_STATE_RUN) { - if (cnf->card->debug_flags & LOG_CNF_MISC) - hysdn_addlog(cnf->card, "cnf write denied -> not booted"); - return (-ERR_NOT_BOOTED); - } - i = (CONF_LINE_LEN - 1) - cnf->buf_size; /* bytes available in buffer */ - if (i > 0) { - /* copy remaining bytes into buffer */ - - if (count > i) - count = i; /* limit transfer */ - if (copy_from_user(cnf->conf_line + cnf->buf_size, buf, count)) - return (-EFAULT); /* error while copying */ - - i = count; /* number of chars in buffer */ - cp = cnf->conf_line + cnf->buf_size; - while (i) { - /* search for end of line */ - if ((*cp < ' ') && (*cp != 9)) - break; /* end of line found */ - cp++; - i--; - } /* search for end of line */ - - if (i) { - /* delimiter found */ - *cp++ = 0; /* string termination */ - count -= (i - 1); /* subtract remaining bytes from count */ - while ((i) && (*cp < ' ') && (*cp != 9)) { - i--; /* discard next char */ - count++; /* mark as read */ - cp++; /* next char */ - } - cnf->buf_size = 0; /* buffer is empty after transfer */ - if ((i = process_line(cnf)) < 0) /* handle the line */ - count = i; /* return the error */ - } - /* delimiter found */ - else { - cnf->buf_size += count; /* add chars to string */ - if (cnf->buf_size >= CONF_LINE_LEN - 1) { - if (cnf->card->debug_flags & LOG_CNF_MISC) - hysdn_addlog(cnf->card, "cnf line too long %d chars pos %d", cnf->buf_size, count); - return (-ERR_CONF_LONG); - } - } /* not delimited */ - - } - /* copy remaining bytes into buffer */ - else { - if (cnf->card->debug_flags & LOG_CNF_MISC) - hysdn_addlog(cnf->card, "cnf line too long"); - return (-ERR_CONF_LONG); - } - } /* conf write active */ - - return (count); -} /* hysdn_conf_write */ - -/*******************************************/ -/* read conf file -> output card info data */ -/*******************************************/ -static ssize_t -hysdn_conf_read(struct file *file, char __user *buf, size_t count, loff_t *off) -{ - char *cp; - - if (!(file->f_mode & FMODE_READ)) - return -EPERM; /* no permission to read */ - - if (!(cp = file->private_data)) - return -EFAULT; /* should never happen */ - - return simple_read_from_buffer(buf, count, off, cp, strlen(cp)); -} /* hysdn_conf_read */ - -/******************/ -/* open conf file */ -/******************/ -static int -hysdn_conf_open(struct inode *ino, struct file *filep) -{ - hysdn_card *card; - struct conf_writedata *cnf; - char *cp, *tmp; - - /* now search the addressed card */ - mutex_lock(&hysdn_conf_mutex); - card = PDE_DATA(ino); - if (card->debug_flags & (LOG_PROC_OPEN | LOG_PROC_ALL)) - hysdn_addlog(card, "config open for uid=%d gid=%d mode=0x%x", - filep->f_cred->fsuid, filep->f_cred->fsgid, - filep->f_mode); - - if ((filep->f_mode & (FMODE_READ | FMODE_WRITE)) == FMODE_WRITE) { - /* write only access -> write boot file or conf line */ - - if (!(cnf = kmalloc(sizeof(struct conf_writedata), GFP_KERNEL))) { - mutex_unlock(&hysdn_conf_mutex); - return (-EFAULT); - } - cnf->card = card; - cnf->buf_size = 0; /* nothing buffered */ - cnf->state = CONF_STATE_DETECT; /* start auto detect */ - filep->private_data = cnf; - - } else if ((filep->f_mode & (FMODE_READ | FMODE_WRITE)) == FMODE_READ) { - /* read access -> output card info data */ - - if (!(tmp = kmalloc(INFO_OUT_LEN * 2 + 2, GFP_KERNEL))) { - mutex_unlock(&hysdn_conf_mutex); - return (-EFAULT); /* out of memory */ - } - filep->private_data = tmp; /* start of string */ - - /* first output a headline */ - sprintf(tmp, "id bus slot type irq iobase dp-mem b-chans fax-chans state device"); - cp = tmp; /* start of string */ - while (*cp) - cp++; - while (((cp - tmp) % (INFO_OUT_LEN + 1)) != INFO_OUT_LEN) - *cp++ = ' '; - *cp++ = '\n'; - - /* and now the data */ - sprintf(cp, "%d %3d %4d %4d %3d 0x%04x 0x%08lx %7d %9d %3d %s", - card->myid, - card->bus, - PCI_SLOT(card->devfn), - card->brdtype, - card->irq, - card->iobase, - card->membase, - card->bchans, - card->faxchans, - card->state, - hysdn_net_getname(card)); - while (*cp) - cp++; - while (((cp - tmp) % (INFO_OUT_LEN + 1)) != INFO_OUT_LEN) - *cp++ = ' '; - *cp++ = '\n'; - *cp = 0; /* end of string */ - } else { /* simultaneous read/write access forbidden ! */ - mutex_unlock(&hysdn_conf_mutex); - return (-EPERM); /* no permission this time */ - } - mutex_unlock(&hysdn_conf_mutex); - return nonseekable_open(ino, filep); -} /* hysdn_conf_open */ - -/***************************/ -/* close a config file. */ -/***************************/ -static int -hysdn_conf_close(struct inode *ino, struct file *filep) -{ - hysdn_card *card; - struct conf_writedata *cnf; - int retval = 0; - - mutex_lock(&hysdn_conf_mutex); - card = PDE_DATA(ino); - if (card->debug_flags & (LOG_PROC_OPEN | LOG_PROC_ALL)) - hysdn_addlog(card, "config close for uid=%d gid=%d mode=0x%x", - filep->f_cred->fsuid, filep->f_cred->fsgid, - filep->f_mode); - - if ((filep->f_mode & (FMODE_READ | FMODE_WRITE)) == FMODE_WRITE) { - /* write only access -> write boot file or conf line */ - if (filep->private_data) { - cnf = filep->private_data; - - if (cnf->state == CONF_STATE_POF) - retval = pof_write_close(cnf->card); /* close the pof write */ - kfree(filep->private_data); /* free allocated memory for buffer */ - - } /* handle write private data */ - } else if ((filep->f_mode & (FMODE_READ | FMODE_WRITE)) == FMODE_READ) { - /* read access -> output card info data */ - - kfree(filep->private_data); /* release memory */ - } - mutex_unlock(&hysdn_conf_mutex); - return (retval); -} /* hysdn_conf_close */ - -/******************************************************/ -/* table for conf filesystem functions defined above. */ -/******************************************************/ -static const struct file_operations conf_fops = -{ - .owner = THIS_MODULE, - .llseek = no_llseek, - .read = hysdn_conf_read, - .write = hysdn_conf_write, - .open = hysdn_conf_open, - .release = hysdn_conf_close, -}; - -/*****************************/ -/* hysdn subdir in /proc/net */ -/*****************************/ -struct proc_dir_entry *hysdn_proc_entry = NULL; - -/*******************************************************************************/ -/* hysdn_procconf_init is called when the module is loaded and after the cards */ -/* have been detected. The needed proc dir and card config files are created. */ -/* The log init is called at last. */ -/*******************************************************************************/ -int -hysdn_procconf_init(void) -{ - hysdn_card *card; - unsigned char conf_name[20]; - - hysdn_proc_entry = proc_mkdir(PROC_SUBDIR_NAME, init_net.proc_net); - if (!hysdn_proc_entry) { - printk(KERN_ERR "HYSDN: unable to create hysdn subdir\n"); - return (-1); - } - card = card_root; /* point to first card */ - while (card) { - - sprintf(conf_name, "%s%d", PROC_CONF_BASENAME, card->myid); - if ((card->procconf = (void *) proc_create_data(conf_name, - S_IFREG | S_IRUGO | S_IWUSR, - hysdn_proc_entry, - &conf_fops, - card)) != NULL) { - hysdn_proclog_init(card); /* init the log file entry */ - } - card = card->next; /* next entry */ - } - - printk(KERN_NOTICE "HYSDN: procfs initialised\n"); - return 0; -} /* hysdn_procconf_init */ - -/*************************************************************************************/ -/* hysdn_procconf_release is called when the module is unloaded and before the cards */ -/* resources are released. The module counter is assumed to be 0 ! */ -/*************************************************************************************/ -void -hysdn_procconf_release(void) -{ - hysdn_card *card; - unsigned char conf_name[20]; - - card = card_root; /* start with first card */ - while (card) { - - sprintf(conf_name, "%s%d", PROC_CONF_BASENAME, card->myid); - if (card->procconf) - remove_proc_entry(conf_name, hysdn_proc_entry); - - hysdn_proclog_release(card); /* init the log file entry */ - - card = card->next; /* point to next card */ - } - - remove_proc_entry(PROC_SUBDIR_NAME, init_net.proc_net); -} diff --git a/drivers/staging/isdn/hysdn/hysdn_proclog.c b/drivers/staging/isdn/hysdn/hysdn_proclog.c deleted file mode 100644 index 6e898b90e86e..000000000000 --- a/drivers/staging/isdn/hysdn/hysdn_proclog.c +++ /dev/null @@ -1,357 +0,0 @@ -/* $Id: hysdn_proclog.c,v 1.9.6.3 2001/09/23 22:24:54 kai Exp $ - * - * Linux driver for HYSDN cards, /proc/net filesystem log functions. - * - * Author Werner Cornelius (werner@titro.de) for Hypercope GmbH - * Copyright 1999 by Werner Cornelius (werner@titro.de) - * - * This software may be used and distributed according to the terms - * of the GNU General Public License, incorporated herein by reference. - * - */ - -#include <linux/module.h> -#include <linux/poll.h> -#include <linux/proc_fs.h> -#include <linux/sched.h> -#include <linux/slab.h> -#include <linux/mutex.h> -#include <linux/kernel.h> - -#include "hysdn_defs.h" - -/* the proc subdir for the interface is defined in the procconf module */ -extern struct proc_dir_entry *hysdn_proc_entry; - -static DEFINE_MUTEX(hysdn_log_mutex); -static void put_log_buffer(hysdn_card *card, char *cp); - -/*************************************************/ -/* structure keeping ascii log for device output */ -/*************************************************/ -struct log_data { - struct log_data *next; - unsigned long usage_cnt;/* number of files still to work */ - void *proc_ctrl; /* pointer to own control procdata structure */ - char log_start[2]; /* log string start (final len aligned by size) */ -}; - -/**********************************************/ -/* structure holding proc entrys for one card */ -/**********************************************/ -struct procdata { - struct proc_dir_entry *log; /* log entry */ - char log_name[15]; /* log filename */ - struct log_data *log_head, *log_tail; /* head and tail for queue */ - int if_used; /* open count for interface */ - unsigned char logtmp[LOG_MAX_LINELEN]; - wait_queue_head_t rd_queue; -}; - - -/**********************************************/ -/* log function for cards error log interface */ -/**********************************************/ -void -hysdn_card_errlog(hysdn_card *card, tErrLogEntry *logp, int maxsize) -{ - char buf[ERRLOG_TEXT_SIZE + 40]; - - sprintf(buf, "LOG 0x%08lX 0x%08lX : %s\n", logp->ulErrType, logp->ulErrSubtype, logp->ucText); - put_log_buffer(card, buf); /* output the string */ -} /* hysdn_card_errlog */ - -/***************************************************/ -/* Log function using format specifiers for output */ -/***************************************************/ -void -hysdn_addlog(hysdn_card *card, char *fmt, ...) -{ - struct procdata *pd = card->proclog; - char *cp; - va_list args; - - if (!pd) - return; /* log structure non existent */ - - cp = pd->logtmp; - cp += sprintf(cp, "HYSDN: card %d ", card->myid); - - va_start(args, fmt); - cp += vsprintf(cp, fmt, args); - va_end(args); - *cp++ = '\n'; - *cp = 0; - - if (card->debug_flags & DEB_OUT_SYSLOG) - printk(KERN_INFO "%s", pd->logtmp); - else - put_log_buffer(card, pd->logtmp); - -} /* hysdn_addlog */ - -/********************************************/ -/* put an log buffer into the log queue. */ -/* This buffer will be kept until all files */ -/* opened for read got the contents. */ -/* Flushes buffers not longer in use. */ -/********************************************/ -static void -put_log_buffer(hysdn_card *card, char *cp) -{ - struct log_data *ib; - struct procdata *pd = card->proclog; - unsigned long flags; - - if (!pd) - return; - if (!cp) - return; - if (!*cp) - return; - if (pd->if_used <= 0) - return; /* no open file for read */ - - if (!(ib = kmalloc(sizeof(struct log_data) + strlen(cp), GFP_ATOMIC))) - return; /* no memory */ - strcpy(ib->log_start, cp); /* set output string */ - ib->next = NULL; - ib->proc_ctrl = pd; /* point to own control structure */ - spin_lock_irqsave(&card->hysdn_lock, flags); - ib->usage_cnt = pd->if_used; - if (!pd->log_head) - pd->log_head = ib; /* new head */ - else - pd->log_tail->next = ib; /* follows existing messages */ - pd->log_tail = ib; /* new tail */ - - /* delete old entrys */ - while (pd->log_head->next) { - if ((pd->log_head->usage_cnt <= 0) && - (pd->log_head->next->usage_cnt <= 0)) { - ib = pd->log_head; - pd->log_head = pd->log_head->next; - kfree(ib); - } else { - break; - } - } /* pd->log_head->next */ - - spin_unlock_irqrestore(&card->hysdn_lock, flags); - - wake_up_interruptible(&(pd->rd_queue)); /* announce new entry */ -} /* put_log_buffer */ - - -/******************************/ -/* file operations and tables */ -/******************************/ - -/****************************************/ -/* write log file -> set log level bits */ -/****************************************/ -static ssize_t -hysdn_log_write(struct file *file, const char __user *buf, size_t count, loff_t *off) -{ - int rc; - hysdn_card *card = file->private_data; - - rc = kstrtoul_from_user(buf, count, 0, &card->debug_flags); - if (rc < 0) - return rc; - hysdn_addlog(card, "debug set to 0x%lx", card->debug_flags); - return (count); -} /* hysdn_log_write */ - -/******************/ -/* read log file */ -/******************/ -static ssize_t -hysdn_log_read(struct file *file, char __user *buf, size_t count, loff_t *off) -{ - struct log_data *inf; - int len; - hysdn_card *card = PDE_DATA(file_inode(file)); - - if (!(inf = *((struct log_data **) file->private_data))) { - struct procdata *pd = card->proclog; - if (file->f_flags & O_NONBLOCK) - return (-EAGAIN); - - wait_event_interruptible(pd->rd_queue, (inf = - *((struct log_data **) file->private_data))); - } - if (!inf) - return (0); - - inf->usage_cnt--; /* new usage count */ - file->private_data = &inf->next; /* next structure */ - if ((len = strlen(inf->log_start)) <= count) { - if (copy_to_user(buf, inf->log_start, len)) - return -EFAULT; - *off += len; - return (len); - } - return (0); -} /* hysdn_log_read */ - -/******************/ -/* open log file */ -/******************/ -static int -hysdn_log_open(struct inode *ino, struct file *filep) -{ - hysdn_card *card = PDE_DATA(ino); - - mutex_lock(&hysdn_log_mutex); - if ((filep->f_mode & (FMODE_READ | FMODE_WRITE)) == FMODE_WRITE) { - /* write only access -> write log level only */ - filep->private_data = card; /* remember our own card */ - } else if ((filep->f_mode & (FMODE_READ | FMODE_WRITE)) == FMODE_READ) { - struct procdata *pd = card->proclog; - unsigned long flags; - - /* read access -> log/debug read */ - spin_lock_irqsave(&card->hysdn_lock, flags); - pd->if_used++; - if (pd->log_head) - filep->private_data = &pd->log_tail->next; - else - filep->private_data = &pd->log_head; - spin_unlock_irqrestore(&card->hysdn_lock, flags); - } else { /* simultaneous read/write access forbidden ! */ - mutex_unlock(&hysdn_log_mutex); - return (-EPERM); /* no permission this time */ - } - mutex_unlock(&hysdn_log_mutex); - return nonseekable_open(ino, filep); -} /* hysdn_log_open */ - -/*******************************************************************************/ -/* close a cardlog file. If the file has been opened for exclusive write it is */ -/* assumed as pof data input and the pof loader is noticed about. */ -/* Otherwise file is handled as log output. In this case the interface usage */ -/* count is decremented and all buffers are noticed of closing. If this file */ -/* was the last one to be closed, all buffers are freed. */ -/*******************************************************************************/ -static int -hysdn_log_close(struct inode *ino, struct file *filep) -{ - struct log_data *inf; - struct procdata *pd; - hysdn_card *card; - int retval = 0; - - mutex_lock(&hysdn_log_mutex); - if ((filep->f_mode & (FMODE_READ | FMODE_WRITE)) == FMODE_WRITE) { - /* write only access -> write debug level written */ - retval = 0; /* success */ - } else { - /* read access -> log/debug read, mark one further file as closed */ - - inf = *((struct log_data **) filep->private_data); /* get first log entry */ - if (inf) - pd = (struct procdata *) inf->proc_ctrl; /* still entries there */ - else { - /* no info available -> search card */ - card = PDE_DATA(file_inode(filep)); - pd = card->proclog; /* pointer to procfs log */ - } - if (pd) - pd->if_used--; /* decrement interface usage count by one */ - - while (inf) { - inf->usage_cnt--; /* decrement usage count for buffers */ - inf = inf->next; - } - - if (pd) - if (pd->if_used <= 0) /* delete buffers if last file closed */ - while (pd->log_head) { - inf = pd->log_head; - pd->log_head = pd->log_head->next; - kfree(inf); - } - } /* read access */ - mutex_unlock(&hysdn_log_mutex); - - return (retval); -} /* hysdn_log_close */ - -/*************************************************/ -/* select/poll routine to be able using select() */ -/*************************************************/ -static __poll_t -hysdn_log_poll(struct file *file, poll_table *wait) -{ - __poll_t mask = 0; - hysdn_card *card = PDE_DATA(file_inode(file)); - struct procdata *pd = card->proclog; - - if ((file->f_mode & (FMODE_READ | FMODE_WRITE)) == FMODE_WRITE) - return (mask); /* no polling for write supported */ - - poll_wait(file, &(pd->rd_queue), wait); - - if (*((struct log_data **) file->private_data)) - mask |= EPOLLIN | EPOLLRDNORM; - - return mask; -} /* hysdn_log_poll */ - -/**************************************************/ -/* table for log filesystem functions defined above. */ -/**************************************************/ -static const struct file_operations log_fops = -{ - .owner = THIS_MODULE, - .llseek = no_llseek, - .read = hysdn_log_read, - .write = hysdn_log_write, - .poll = hysdn_log_poll, - .open = hysdn_log_open, - .release = hysdn_log_close, -}; - - -/***********************************************************************************/ -/* hysdn_proclog_init is called when the module is loaded after creating the cards */ -/* conf files. */ -/***********************************************************************************/ -int -hysdn_proclog_init(hysdn_card *card) -{ - struct procdata *pd; - - /* create a cardlog proc entry */ - - if ((pd = kzalloc(sizeof(struct procdata), GFP_KERNEL)) != NULL) { - sprintf(pd->log_name, "%s%d", PROC_LOG_BASENAME, card->myid); - pd->log = proc_create_data(pd->log_name, - S_IFREG | S_IRUGO | S_IWUSR, hysdn_proc_entry, - &log_fops, card); - - init_waitqueue_head(&(pd->rd_queue)); - - card->proclog = (void *) pd; /* remember procfs structure */ - } - return (0); -} /* hysdn_proclog_init */ - -/************************************************************************************/ -/* hysdn_proclog_release is called when the module is unloaded and before the cards */ -/* conf file is released */ -/* The module counter is assumed to be 0 ! */ -/************************************************************************************/ -void -hysdn_proclog_release(hysdn_card *card) -{ - struct procdata *pd; - - if ((pd = (struct procdata *) card->proclog) != NULL) { - if (pd->log) - remove_proc_entry(pd->log_name, hysdn_proc_entry); - kfree(pd); /* release memory */ - card->proclog = NULL; - } -} /* hysdn_proclog_release */ diff --git a/drivers/staging/isdn/hysdn/hysdn_sched.c b/drivers/staging/isdn/hysdn/hysdn_sched.c deleted file mode 100644 index 31d7c1415543..000000000000 --- a/drivers/staging/isdn/hysdn/hysdn_sched.c +++ /dev/null @@ -1,197 +0,0 @@ -/* $Id: hysdn_sched.c,v 1.5.6.4 2001/11/06 21:58:19 kai Exp $ - * - * Linux driver for HYSDN cards - * scheduler routines for handling exchange card <-> pc. - * - * Author Werner Cornelius (werner@titro.de) for Hypercope GmbH - * Copyright 1999 by Werner Cornelius (werner@titro.de) - * - * This software may be used and distributed according to the terms - * of the GNU General Public License, incorporated herein by reference. - * - */ - -#include <linux/signal.h> -#include <linux/kernel.h> -#include <linux/ioport.h> -#include <linux/interrupt.h> -#include <linux/delay.h> -#include <asm/io.h> - -#include "hysdn_defs.h" - -/*****************************************************************************/ -/* hysdn_sched_rx is called from the cards handler to announce new data is */ -/* available from the card. The routine has to handle the data and return */ -/* with a nonzero code if the data could be worked (or even thrown away), if */ -/* no room to buffer the data is available a zero return tells the card */ -/* to keep the data until later. */ -/*****************************************************************************/ -int -hysdn_sched_rx(hysdn_card *card, unsigned char *buf, unsigned short len, - unsigned short chan) -{ - - switch (chan) { - case CHAN_NDIS_DATA: - if (hynet_enable & (1 << card->myid)) { - /* give packet to network handler */ - hysdn_rx_netpkt(card, buf, len); - } - break; - - case CHAN_ERRLOG: - hysdn_card_errlog(card, (tErrLogEntry *) buf, len); - if (card->err_log_state == ERRLOG_STATE_ON) - card->err_log_state = ERRLOG_STATE_START; /* start new fetch */ - break; -#ifdef CONFIG_HYSDN_CAPI - case CHAN_CAPI: -/* give packet to CAPI handler */ - if (hycapi_enable & (1 << card->myid)) { - hycapi_rx_capipkt(card, buf, len); - } - break; -#endif /* CONFIG_HYSDN_CAPI */ - default: - printk(KERN_INFO "irq message channel %d len %d unhandled \n", chan, len); - break; - - } /* switch rx channel */ - - return (1); /* always handled */ -} /* hysdn_sched_rx */ - -/*****************************************************************************/ -/* hysdn_sched_tx is called from the cards handler to announce that there is */ -/* room in the tx-buffer to the card and data may be sent if needed. */ -/* If the routine wants to send data it must fill buf, len and chan with the */ -/* appropriate data and return a nonzero value. With a zero return no new */ -/* data to send is assumed. maxlen specifies the buffer size available for */ -/* sending. */ -/*****************************************************************************/ -int -hysdn_sched_tx(hysdn_card *card, unsigned char *buf, - unsigned short volatile *len, unsigned short volatile *chan, - unsigned short maxlen) -{ - struct sk_buff *skb; - - if (card->net_tx_busy) { - card->net_tx_busy = 0; /* reset flag */ - hysdn_tx_netack(card); /* acknowledge packet send */ - } /* a network packet has completely been transferred */ - /* first of all async requests are handled */ - if (card->async_busy) { - if (card->async_len <= maxlen) { - memcpy(buf, card->async_data, card->async_len); - *len = card->async_len; - *chan = card->async_channel; - card->async_busy = 0; /* reset request */ - return (1); - } - card->async_busy = 0; /* in case of length error */ - } /* async request */ - if ((card->err_log_state == ERRLOG_STATE_START) && - (maxlen >= ERRLOG_CMD_REQ_SIZE)) { - strcpy(buf, ERRLOG_CMD_REQ); /* copy the command */ - *len = ERRLOG_CMD_REQ_SIZE; /* buffer length */ - *chan = CHAN_ERRLOG; /* and channel */ - card->err_log_state = ERRLOG_STATE_ON; /* new state is on */ - return (1); /* tell that data should be send */ - } /* error log start and able to send */ - if ((card->err_log_state == ERRLOG_STATE_STOP) && - (maxlen >= ERRLOG_CMD_STOP_SIZE)) { - strcpy(buf, ERRLOG_CMD_STOP); /* copy the command */ - *len = ERRLOG_CMD_STOP_SIZE; /* buffer length */ - *chan = CHAN_ERRLOG; /* and channel */ - card->err_log_state = ERRLOG_STATE_OFF; /* new state is off */ - return (1); /* tell that data should be send */ - } /* error log start and able to send */ - /* now handle network interface packets */ - if ((hynet_enable & (1 << card->myid)) && - (skb = hysdn_tx_netget(card)) != NULL) - { - if (skb->len <= maxlen) { - /* copy the packet to the buffer */ - skb_copy_from_linear_data(skb, buf, skb->len); - *len = skb->len; - *chan = CHAN_NDIS_DATA; - card->net_tx_busy = 1; /* we are busy sending network data */ - return (1); /* go and send the data */ - } else - hysdn_tx_netack(card); /* aknowledge packet -> throw away */ - } /* send a network packet if available */ -#ifdef CONFIG_HYSDN_CAPI - if (((hycapi_enable & (1 << card->myid))) && - ((skb = hycapi_tx_capiget(card)) != NULL)) - { - if (skb->len <= maxlen) { - skb_copy_from_linear_data(skb, buf, skb->len); - *len = skb->len; - *chan = CHAN_CAPI; - hycapi_tx_capiack(card); - return (1); /* go and send the data */ - } - } -#endif /* CONFIG_HYSDN_CAPI */ - return (0); /* nothing to send */ -} /* hysdn_sched_tx */ - - -/*****************************************************************************/ -/* send one config line to the card and return 0 if successful, otherwise a */ -/* negative error code. */ -/* The function works with timeouts perhaps not giving the greatest speed */ -/* sending the line, but this should be meaningless because only some lines */ -/* are to be sent and this happens very seldom. */ -/*****************************************************************************/ -int -hysdn_tx_cfgline(hysdn_card *card, unsigned char *line, unsigned short chan) -{ - int cnt = 50; /* timeout intervalls */ - unsigned long flags; - - if (card->debug_flags & LOG_SCHED_ASYN) - hysdn_addlog(card, "async tx-cfg chan=%d len=%d", chan, strlen(line) + 1); - - while (card->async_busy) { - - if (card->debug_flags & LOG_SCHED_ASYN) - hysdn_addlog(card, "async tx-cfg delayed"); - - msleep_interruptible(20); /* Timeout 20ms */ - if (!--cnt) - return (-ERR_ASYNC_TIME); /* timed out */ - } /* wait for buffer to become free */ - - spin_lock_irqsave(&card->hysdn_lock, flags); - strcpy(card->async_data, line); - card->async_len = strlen(line) + 1; - card->async_channel = chan; - card->async_busy = 1; /* request transfer */ - - /* now queue the task */ - schedule_work(&card->irq_queue); - spin_unlock_irqrestore(&card->hysdn_lock, flags); - - if (card->debug_flags & LOG_SCHED_ASYN) - hysdn_addlog(card, "async tx-cfg data queued"); - - cnt++; /* short delay */ - - while (card->async_busy) { - - if (card->debug_flags & LOG_SCHED_ASYN) - hysdn_addlog(card, "async tx-cfg waiting for tx-ready"); - - msleep_interruptible(20); /* Timeout 20ms */ - if (!--cnt) - return (-ERR_ASYNC_TIME); /* timed out */ - } /* wait for buffer to become free again */ - - if (card->debug_flags & LOG_SCHED_ASYN) - hysdn_addlog(card, "async tx-cfg data send"); - - return (0); /* line send correctly */ -} /* hysdn_tx_cfgline */ diff --git a/drivers/staging/isdn/hysdn/ince1pc.h b/drivers/staging/isdn/hysdn/ince1pc.h deleted file mode 100644 index cab68361de65..000000000000 --- a/drivers/staging/isdn/hysdn/ince1pc.h +++ /dev/null @@ -1,134 +0,0 @@ -/* - * Linux driver for HYSDN cards - * common definitions for both sides of the bus: - * - conventions both spoolers must know - * - channel numbers agreed upon - * - * Author M. Steinkopf - * Copyright 1999 by M. Steinkopf - * - * This software may be used and distributed according to the terms - * of the GNU General Public License, incorporated herein by reference. - * - */ - -#ifndef __INCE1PC_H__ -#define __INCE1PC_H__ - -/* basic scalar definitions have same meanning, - * but their declaration location depends on environment - */ - -/*--------------------------------------channel numbers---------------------*/ -#define CHAN_SYSTEM 0x0001 /* system channel (spooler to spooler) */ -#define CHAN_ERRLOG 0x0005 /* error logger */ -#define CHAN_CAPI 0x0064 /* CAPI interface */ -#define CHAN_NDIS_DATA 0x1001 /* NDIS data transfer */ - -/*--------------------------------------POF ready msg-----------------------*/ -/* NOTE: after booting POF sends system ready message to PC: */ -#define RDY_MAGIC 0x52535953UL /* 'SYSR' reversed */ -#define RDY_MAGIC_SIZE 4 /* size in bytes */ - -#define MAX_N_TOK_BYTES 255 - -#define MIN_RDY_MSG_SIZE RDY_MAGIC_SIZE -#define MAX_RDY_MSG_SIZE (RDY_MAGIC_SIZE + MAX_N_TOK_BYTES) - -#define SYSR_TOK_END 0 -#define SYSR_TOK_B_CHAN 1 /* nr. of B-Channels; DataLen=1; def: 2 */ -#define SYSR_TOK_FAX_CHAN 2 /* nr. of FAX Channels; DataLen=1; def: 0 */ -#define SYSR_TOK_MAC_ADDR 3 /* MAC-Address; DataLen=6; def: auto */ -#define SYSR_TOK_ESC 255 /* undefined data size yet */ -/* default values, if not corrected by token: */ -#define SYSR_TOK_B_CHAN_DEF 2 /* assume 2 B-Channels */ -#define SYSR_TOK_FAX_CHAN_DEF 1 /* assume 1 FAX Channel */ - -/* syntax of new SYSR token stream: - * channel: CHAN_SYSTEM - * msgsize: MIN_RDY_MSG_SIZE <= x <= MAX_RDY_MSG_SIZE - * RDY_MAGIC_SIZE <= x <= (RDY_MAGIC_SIZE+MAX_N_TOK_BYTES) - * msg : 0 1 2 3 {4 5 6 ..} - * S Y S R MAX_N_TOK_BYTES bytes of TokenStream - * - * TokenStream := empty - * | {NonEndTokenChunk} EndToken RotlCRC - * NonEndTokenChunk:= NonEndTokenId DataLen [Data] - * NonEndTokenId := 0x01 .. 0xFE 1 BYTE - * DataLen := 0x00 .. 0xFF 1 BYTE - * Data := DataLen bytes - * EndToken := 0x00 - * RotlCRC := special 1 byte CRC over all NonEndTokenChunk bytes - * s. RotlCRC algorithm - * - * RotlCRC algorithm: - * ucSum= 0 1 unsigned char - * for all NonEndTokenChunk bytes: - * ROTL(ucSum,1) rotate left by 1 - * ucSum += Char; add current byte with swap around - * RotlCRC= ~ucSum; invert all bits for result - * - * note: - * - for 16-bit FIFO add padding 0 byte to achieve even token data bytes! - */ - -/*--------------------------------------error logger------------------------*/ -/* note: pof needs final 0 ! */ -#define ERRLOG_CMD_REQ "ERRLOG ON" -#define ERRLOG_CMD_REQ_SIZE 10 /* with final 0 byte ! */ -#define ERRLOG_CMD_STOP "ERRLOG OFF" -#define ERRLOG_CMD_STOP_SIZE 11 /* with final 0 byte ! */ - -#define ERRLOG_ENTRY_SIZE 64 /* sizeof(tErrLogEntry) */ - /* remaining text size = 55 */ -#define ERRLOG_TEXT_SIZE (ERRLOG_ENTRY_SIZE - 2 * 4 - 1) - -typedef struct ErrLogEntry_tag { - - /*00 */ unsigned long ulErrType; - - /*04 */ unsigned long ulErrSubtype; - - /*08 */ unsigned char ucTextSize; - - /*09 */ unsigned char ucText[ERRLOG_TEXT_SIZE]; - /* ASCIIZ of len ucTextSize-1 */ - -/*40 */ -} tErrLogEntry; - - -#if defined(__TURBOC__) -#if sizeof(tErrLogEntry) != ERRLOG_ENTRY_SIZE -#error size of tErrLogEntry != ERRLOG_ENTRY_SIZE -#endif /* */ -#endif /* */ - -/*--------------------------------------DPRAM boot spooler------------------*/ -/* this is the struture used between pc and - * hyperstone to exchange boot data - */ -#define DPRAM_SPOOLER_DATA_SIZE 0x20 -typedef struct DpramBootSpooler_tag { - - /*00 */ unsigned char Len; - - /*01 */ volatile unsigned char RdPtr; - - /*02 */ unsigned char WrPtr; - - /*03 */ unsigned char Data[DPRAM_SPOOLER_DATA_SIZE]; - -/*23 */ -} tDpramBootSpooler; - - -#define DPRAM_SPOOLER_MIN_SIZE 5 /* Len+RdPtr+Wrptr+2*data */ -#define DPRAM_SPOOLER_DEF_SIZE 0x23 /* current default size */ - -/*--------------------------------------HYCARD/ERGO DPRAM SoftUart----------*/ -/* at DPRAM offset 0x1C00: */ -#define SIZE_RSV_SOFT_UART 0x1B0 /* 432 bytes reserved for SoftUart */ - - -#endif /* __INCE1PC_H__ */ diff --git a/drivers/staging/kpc2000/kpc2000_i2c.c b/drivers/staging/kpc2000/kpc2000_i2c.c index 592099a1fca5..25bb5c97dd21 100644 --- a/drivers/staging/kpc2000/kpc2000_i2c.c +++ b/drivers/staging/kpc2000/kpc2000_i2c.c @@ -32,7 +32,7 @@ MODULE_LICENSE("GPL"); MODULE_AUTHOR("Matt.Sickler@Daktronics.com"); -struct i2c_device { +struct kpc_i2c { unsigned long smba; struct i2c_adapter adapter; unsigned int features; @@ -131,7 +131,7 @@ struct i2c_device { /* Make sure the SMBus host is ready to start transmitting. * Return 0 if it is, -EBUSY if it is not. */ -static int i801_check_pre(struct i2c_device *priv) +static int i801_check_pre(struct kpc_i2c *priv) { int status; @@ -156,7 +156,7 @@ static int i801_check_pre(struct i2c_device *priv) } /* Convert the status register to an error code, and clear it. */ -static int i801_check_post(struct i2c_device *priv, int status, int timeout) +static int i801_check_post(struct kpc_i2c *priv, int status, int timeout) { int result = 0; @@ -206,7 +206,7 @@ static int i801_check_post(struct i2c_device *priv, int status, int timeout) return result; } -static int i801_transaction(struct i2c_device *priv, int xact) +static int i801_transaction(struct kpc_i2c *priv, int xact) { int status; int result; @@ -235,7 +235,7 @@ static int i801_transaction(struct i2c_device *priv, int xact) } /* wait for INTR bit as advised by Intel */ -static void i801_wait_hwpec(struct i2c_device *priv) +static void i801_wait_hwpec(struct kpc_i2c *priv) { int timeout = 0; int status; @@ -251,7 +251,7 @@ static void i801_wait_hwpec(struct i2c_device *priv) outb_p(status, SMBHSTSTS(priv)); } -static int i801_block_transaction_by_block(struct i2c_device *priv, +static int i801_block_transaction_by_block(struct kpc_i2c *priv, union i2c_smbus_data *data, char read_write, int hwpec) { @@ -285,7 +285,7 @@ static int i801_block_transaction_by_block(struct i2c_device *priv, return 0; } -static int i801_block_transaction_byte_by_byte(struct i2c_device *priv, +static int i801_block_transaction_byte_by_byte(struct kpc_i2c *priv, union i2c_smbus_data *data, char read_write, int command, int hwpec) @@ -367,7 +367,7 @@ static int i801_block_transaction_byte_by_byte(struct i2c_device *priv, return 0; } -static int i801_set_block_buffer_mode(struct i2c_device *priv) +static int i801_set_block_buffer_mode(struct kpc_i2c *priv) { outb_p(inb_p(SMBAUXCTL(priv)) | SMBAUXCTL_E32B, SMBAUXCTL(priv)); if ((inb_p(SMBAUXCTL(priv)) & SMBAUXCTL_E32B) == 0) @@ -376,7 +376,7 @@ static int i801_set_block_buffer_mode(struct i2c_device *priv) } /* Block transaction function */ -static int i801_block_transaction(struct i2c_device *priv, +static int i801_block_transaction(struct kpc_i2c *priv, union i2c_smbus_data *data, char read_write, int command, int hwpec) { @@ -440,7 +440,7 @@ static s32 i801_access(struct i2c_adapter *adap, u16 addr, int hwpec; int block = 0; int ret, xact = 0; - struct i2c_device *priv = i2c_get_adapdata(adap); + struct kpc_i2c *priv = i2c_get_adapdata(adap); hwpec = (priv->features & FEATURE_SMBUS_PEC) && (flags & I2C_CLIENT_PEC) && @@ -572,9 +572,13 @@ static s32 i801_access(struct i2c_adapter *adap, u16 addr, return 0; } +#define enable_flag(x) (x) +#define disable_flag(x) 0 +#define enable_flag_if(x, cond) ((cond) ? (x) : 0) + static u32 i801_func(struct i2c_adapter *adapter) { - struct i2c_device *priv = i2c_get_adapdata(adapter); + struct kpc_i2c *priv = i2c_get_adapdata(adapter); /* original settings * u32 f = I2C_FUNC_SMBUS_QUICK | I2C_FUNC_SMBUS_BYTE | @@ -588,42 +592,42 @@ static u32 i801_func(struct i2c_adapter *adapter) // http://lxr.free-electrons.com/source/include/uapi/linux/i2c.h#L85 u32 f = - I2C_FUNC_I2C | /* 0x00000001(I enabled this - * one) - */ - !I2C_FUNC_10BIT_ADDR | /* 0x00000002 */ - !I2C_FUNC_PROTOCOL_MANGLING | /* 0x00000004 */ - ((priv->features & FEATURE_SMBUS_PEC) ? - I2C_FUNC_SMBUS_PEC : 0) | /* 0x00000008 */ - !I2C_FUNC_SMBUS_BLOCK_PROC_CALL | /* 0x00008000 */ - I2C_FUNC_SMBUS_QUICK | /* 0x00010000 */ - !I2C_FUNC_SMBUS_READ_BYTE | /* 0x00020000 */ - !I2C_FUNC_SMBUS_WRITE_BYTE | /* 0x00040000 */ - !I2C_FUNC_SMBUS_READ_BYTE_DATA | /* 0x00080000 */ - !I2C_FUNC_SMBUS_WRITE_BYTE_DATA | /* 0x00100000 */ - !I2C_FUNC_SMBUS_READ_WORD_DATA | /* 0x00200000 */ - !I2C_FUNC_SMBUS_WRITE_WORD_DATA | /* 0x00400000 */ - !I2C_FUNC_SMBUS_PROC_CALL | /* 0x00800000 */ - !I2C_FUNC_SMBUS_READ_BLOCK_DATA | /* 0x01000000 */ - !I2C_FUNC_SMBUS_WRITE_BLOCK_DATA | /* 0x02000000 */ - ((priv->features & FEATURE_I2C_BLOCK_READ) ? - I2C_FUNC_SMBUS_READ_I2C_BLOCK : 0) | /* 0x04000000 */ - I2C_FUNC_SMBUS_WRITE_I2C_BLOCK | /* 0x08000000 */ - - I2C_FUNC_SMBUS_BYTE | /* _READ_BYTE _WRITE_BYTE */ - I2C_FUNC_SMBUS_BYTE_DATA | /* _READ_BYTE_DATA - * _WRITE_BYTE_DATA - */ - I2C_FUNC_SMBUS_WORD_DATA | /* _READ_WORD_DATA - * _WRITE_WORD_DATA - */ - I2C_FUNC_SMBUS_BLOCK_DATA | /* _READ_BLOCK_DATA - * _WRITE_BLOCK_DATA - */ - !I2C_FUNC_SMBUS_I2C_BLOCK | /* _READ_I2C_BLOCK - * _WRITE_I2C_BLOCK - */ - !I2C_FUNC_SMBUS_EMUL; /* _QUICK _BYTE + enable_flag(I2C_FUNC_I2C) | /* 0x00000001(I enabled this one) */ + disable_flag(I2C_FUNC_10BIT_ADDR) | /* 0x00000002 */ + disable_flag(I2C_FUNC_PROTOCOL_MANGLING) | /* 0x00000004 */ + enable_flag_if(I2C_FUNC_SMBUS_PEC, + priv->features & FEATURE_SMBUS_PEC) | + /* 0x00000008 */ + disable_flag(I2C_FUNC_SMBUS_BLOCK_PROC_CALL) | /* 0x00008000 */ + enable_flag(I2C_FUNC_SMBUS_QUICK) | /* 0x00010000 */ + disable_flag(I2C_FUNC_SMBUS_READ_BYTE) | /* 0x00020000 */ + disable_flag(I2C_FUNC_SMBUS_WRITE_BYTE) | /* 0x00040000 */ + disable_flag(I2C_FUNC_SMBUS_READ_BYTE_DATA) | /* 0x00080000 */ + disable_flag(I2C_FUNC_SMBUS_WRITE_BYTE_DATA) | /* 0x00100000 */ + disable_flag(I2C_FUNC_SMBUS_READ_WORD_DATA) | /* 0x00200000 */ + disable_flag(I2C_FUNC_SMBUS_WRITE_WORD_DATA) | /* 0x00400000 */ + disable_flag(I2C_FUNC_SMBUS_PROC_CALL) | /* 0x00800000 */ + disable_flag(I2C_FUNC_SMBUS_READ_BLOCK_DATA) | /* 0x01000000 */ + disable_flag(I2C_FUNC_SMBUS_WRITE_BLOCK_DATA) | /* 0x02000000 */ + enable_flag_if(I2C_FUNC_SMBUS_READ_I2C_BLOCK, + priv->features & FEATURE_I2C_BLOCK_READ) | + /* 0x04000000 */ + enable_flag(I2C_FUNC_SMBUS_WRITE_I2C_BLOCK) | /* 0x08000000 */ + + enable_flag(I2C_FUNC_SMBUS_BYTE) | /* _READ_BYTE _WRITE_BYTE */ + enable_flag(I2C_FUNC_SMBUS_BYTE_DATA) | /* _READ_BYTE_DATA + * _WRITE_BYTE_DATA + */ + enable_flag(I2C_FUNC_SMBUS_WORD_DATA) | /* _READ_WORD_DATA + * _WRITE_WORD_DATA + */ + enable_flag(I2C_FUNC_SMBUS_BLOCK_DATA) | /* _READ_BLOCK_DATA + * _WRITE_BLOCK_DATA + */ + disable_flag(I2C_FUNC_SMBUS_I2C_BLOCK) | /* _READ_I2C_BLOCK + * _WRITE_I2C_BLOCK + */ + disable_flag(I2C_FUNC_SMBUS_EMUL); /* _QUICK _BYTE * _BYTE_DATA _WORD_DATA * _PROC_CALL * _WRITE_BLOCK_DATA @@ -632,6 +636,10 @@ static u32 i801_func(struct i2c_adapter *adapter) return f; } +#undef enable_flag +#undef disable_flag +#undef enable_flag_if + static const struct i2c_algorithm smbus_algorithm = { .smbus_xfer = i801_access, .functionality = i801_func, @@ -640,10 +648,10 @@ static const struct i2c_algorithm smbus_algorithm = { /******************************** *** Part 2 - Driver Handlers *** ********************************/ -static int pi2c_probe(struct platform_device *pldev) +static int kpc_i2c_probe(struct platform_device *pldev) { int err; - struct i2c_device *priv; + struct kpc_i2c *priv; struct resource *res; priv = devm_kzalloc(&pldev->dev, sizeof(*priv), GFP_KERNEL); @@ -692,11 +700,11 @@ static int pi2c_probe(struct platform_device *pldev) return 0; } -static int pi2c_remove(struct platform_device *pldev) +static int kpc_i2c_remove(struct platform_device *pldev) { - struct i2c_device *lddev; + struct kpc_i2c *lddev; - lddev = (struct i2c_device *)platform_get_drvdata(pldev); + lddev = (struct kpc_i2c *)platform_get_drvdata(pldev); i2c_del_adapter(&lddev->adapter); @@ -710,12 +718,12 @@ static int pi2c_remove(struct platform_device *pldev) return 0; } -static struct platform_driver i2c_plat_driver_i = { - .probe = pi2c_probe, - .remove = pi2c_remove, +static struct platform_driver kpc_i2c_driver = { + .probe = kpc_i2c_probe, + .remove = kpc_i2c_remove, .driver = { .name = KP_DRIVER_NAME_I2C, }, }; -module_platform_driver(i2c_plat_driver_i); +module_platform_driver(kpc_i2c_driver); diff --git a/drivers/staging/kpc2000/kpc_dma/fileops.c b/drivers/staging/kpc2000/kpc_dma/fileops.c index cb52bd9a6d2f..40525540dde6 100644 --- a/drivers/staging/kpc2000/kpc_dma/fileops.c +++ b/drivers/staging/kpc2000/kpc_dma/fileops.c @@ -49,9 +49,7 @@ static int kpc_dma_transfer(struct dev_private_data *priv, u64 dma_addr; u64 user_ctl; - BUG_ON(priv == NULL); ldev = priv->ldev; - BUG_ON(ldev == NULL); acd = kzalloc(sizeof(*acd), GFP_KERNEL); if (!acd) { diff --git a/drivers/staging/most/Makefile b/drivers/staging/most/Makefile index 85ea5a434ced..20a99ecb37c4 100644 --- a/drivers/staging/most/Makefile +++ b/drivers/staging/most/Makefile @@ -2,7 +2,6 @@ obj-$(CONFIG_MOST) += most_core.o most_core-y := core.o most_core-y += configfs.o -ccflags-y += -I $(srctree)/drivers/staging/ obj-$(CONFIG_MOST_CDEV) += cdev/ obj-$(CONFIG_MOST_NET) += net/ diff --git a/drivers/staging/most/cdev/Makefile b/drivers/staging/most/cdev/Makefile index 9f4a8b8c9c27..ef90cd71994a 100644 --- a/drivers/staging/most/cdev/Makefile +++ b/drivers/staging/most/cdev/Makefile @@ -2,4 +2,3 @@ obj-$(CONFIG_MOST_CDEV) += most_cdev.o most_cdev-objs := cdev.o -ccflags-y += -I $(srctree)/drivers/staging/ diff --git a/drivers/staging/most/cdev/cdev.c b/drivers/staging/most/cdev/cdev.c index f880147c82fd..71943d17f825 100644 --- a/drivers/staging/most/cdev/cdev.c +++ b/drivers/staging/most/cdev/cdev.c @@ -16,7 +16,8 @@ #include <linux/kfifo.h> #include <linux/uaccess.h> #include <linux/idr.h> -#include "most/core.h" + +#include "../most.h" #define CHRDEV_REGION_SIZE 50 @@ -25,7 +26,7 @@ static struct cdev_component { struct ida minor_id; unsigned int major; struct class *class; - struct core_component cc; + struct most_component cc; } comp; struct comp_channel { diff --git a/drivers/staging/most/configfs.c b/drivers/staging/most/configfs.c index 34a9fb53985c..9a961222f458 100644 --- a/drivers/staging/most/configfs.c +++ b/drivers/staging/most/configfs.c @@ -10,7 +10,10 @@ #include <linux/slab.h> #include <linux/init.h> #include <linux/configfs.h> -#include <most/core.h> + +#include "most.h" + +#define MAX_STRING_SIZE 80 struct mdev_link { struct config_item item; @@ -22,13 +25,13 @@ struct mdev_link { u16 subbuffer_size; u16 packets_per_xact; u16 dbr_size; - char datatype[PAGE_SIZE]; - char direction[PAGE_SIZE]; - char name[PAGE_SIZE]; - char device[PAGE_SIZE]; - char channel[PAGE_SIZE]; - char comp[PAGE_SIZE]; - char comp_params[PAGE_SIZE]; + char datatype[MAX_STRING_SIZE]; + char direction[MAX_STRING_SIZE]; + char name[MAX_STRING_SIZE]; + char device[MAX_STRING_SIZE]; + char channel[MAX_STRING_SIZE]; + char comp[MAX_STRING_SIZE]; + char comp_params[MAX_STRING_SIZE]; }; static struct list_head mdev_link_list; @@ -125,6 +128,8 @@ static ssize_t mdev_link_create_link_store(struct config_item *item, return ret; list_add_tail(&mdev_link->list, &mdev_link_list); mdev_link->create_link = tmp; + mdev_link->destroy_link = false; + return count; } @@ -140,13 +145,16 @@ static ssize_t mdev_link_destroy_link_store(struct config_item *item, return ret; if (!tmp) return count; - mdev_link->destroy_link = tmp; + ret = most_remove_link(mdev_link->device, mdev_link->channel, mdev_link->comp); if (ret) return ret; if (!list_empty(&mdev_link_list)) list_del(&mdev_link->list); + + mdev_link->destroy_link = tmp; + return count; } @@ -197,7 +205,7 @@ static ssize_t mdev_link_device_store(struct config_item *item, { struct mdev_link *mdev_link = to_mdev_link(item); - strcpy(mdev_link->device, page); + strlcpy(mdev_link->device, page, sizeof(mdev_link->device)); strim(mdev_link->device); return count; } @@ -212,7 +220,7 @@ static ssize_t mdev_link_channel_store(struct config_item *item, { struct mdev_link *mdev_link = to_mdev_link(item); - strcpy(mdev_link->channel, page); + strlcpy(mdev_link->channel, page, sizeof(mdev_link->channel)); strim(mdev_link->channel); return count; } @@ -227,7 +235,8 @@ static ssize_t mdev_link_comp_store(struct config_item *item, { struct mdev_link *mdev_link = to_mdev_link(item); - strcpy(mdev_link->comp, page); + strlcpy(mdev_link->comp, page, sizeof(mdev_link->comp)); + strim(mdev_link->comp); return count; } @@ -242,7 +251,8 @@ static ssize_t mdev_link_comp_params_store(struct config_item *item, { struct mdev_link *mdev_link = to_mdev_link(item); - strcpy(mdev_link->comp_params, page); + strlcpy(mdev_link->comp_params, page, sizeof(mdev_link->comp_params)); + strim(mdev_link->comp_params); return count; } @@ -373,13 +383,20 @@ static void mdev_link_release(struct config_item *item) struct mdev_link *mdev_link = to_mdev_link(item); int ret; - if (!list_empty(&mdev_link_list)) { - ret = most_remove_link(mdev_link->device, mdev_link->channel, - mdev_link->comp); - if (ret && (ret != -ENODEV)) - pr_err("Removing link failed.\n"); - list_del(&mdev_link->list); + if (mdev_link->destroy_link) + goto free_item; + + ret = most_remove_link(mdev_link->device, mdev_link->channel, + mdev_link->comp); + if (ret) { + pr_err("Removing link failed.\n"); + goto free_item; } + + if (!list_empty(&mdev_link_list)) + list_del(&mdev_link->list); + +free_item: kfree(to_mdev_link(item)); } @@ -630,7 +647,7 @@ static struct most_sound most_sound_subsys = { }, }; -int most_register_configfs_subsys(struct core_component *c) +int most_register_configfs_subsys(struct most_component *c) { int ret; @@ -674,7 +691,7 @@ void most_interface_register_notify(const char *mdev) most_cfg_complete("sound"); } -void most_deregister_configfs_subsys(struct core_component *c) +void most_deregister_configfs_subsys(struct most_component *c) { if (!strcmp(c->name, "cdev")) configfs_unregister_subsystem(&most_cdev.subsys); diff --git a/drivers/staging/most/core.c b/drivers/staging/most/core.c index 51a6b41d5b82..0c4ae6920d77 100644 --- a/drivers/staging/most/core.c +++ b/drivers/staging/most/core.c @@ -2,10 +2,9 @@ /* * core.c - Implementation of core module of MOST Linux driver stack * - * Copyright (C) 2013-2015 Microchip Technology Germany II GmbH & Co. KG + * Copyright (C) 2013-2020 Microchip Technology Germany II GmbH & Co. KG */ -#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt #include <linux/module.h> #include <linux/fs.h> #include <linux/slab.h> @@ -21,25 +20,18 @@ #include <linux/kthread.h> #include <linux/dma-mapping.h> #include <linux/idr.h> -#include <most/core.h> + +#include "most.h" #define MAX_CHANNELS 64 #define STRING_SIZE 80 static struct ida mdev_id; static int dummy_num_buffers; - -static struct mostcore { - struct device dev; - struct device_driver drv; - struct bus_type bus; - struct list_head comp_list; -} mc; - -#define to_driver(d) container_of(d, struct mostcore, drv) +static struct list_head comp_list; struct pipe { - struct core_component *comp; + struct most_component *comp; int refs; int num_buffers; }; @@ -151,7 +143,7 @@ static void flush_channel_fifos(struct most_channel *c) spin_unlock_irqrestore(&c->fifo_lock, hf_flags); if (unlikely((!list_empty(&c->fifo) || !list_empty(&c->halt_fifo)))) - pr_info("WARN: fifo | trash fifo not empty\n"); + dev_warn(&c->dev, "Channel or trash fifo not empty\n"); } /** @@ -402,7 +394,7 @@ static ssize_t description_show(struct device *dev, struct device_attribute *attr, char *buf) { - struct most_interface *iface = to_most_interface(dev); + struct most_interface *iface = dev_get_drvdata(dev); return snprintf(buf, PAGE_SIZE, "%s\n", iface->description); } @@ -411,7 +403,7 @@ static ssize_t interface_show(struct device *dev, struct device_attribute *attr, char *buf) { - struct most_interface *iface = to_most_interface(dev); + struct most_interface *iface = dev_get_drvdata(dev); switch (iface->interface) { case ITYPE_LOOPBACK: @@ -454,11 +446,11 @@ static const struct attribute_group *interface_attr_groups[] = { NULL, }; -static struct core_component *match_component(char *name) +static struct most_component *match_component(char *name) { - struct core_component *comp; + struct most_component *comp; - list_for_each_entry(comp, &mc.comp_list, list) { + list_for_each_entry(comp, &comp_list, list) { if (!strcmp(comp->name, name)) return comp; } @@ -476,7 +468,7 @@ static int print_links(struct device *dev, void *data) int offs = d->offs; char *buf = d->buf; struct most_channel *c; - struct most_interface *iface = to_most_interface(dev); + struct most_interface *iface = dev_get_drvdata(dev); list_for_each_entry(c, &iface->p->channel_list, list) { if (c->pipe0.comp) { @@ -484,7 +476,7 @@ static int print_links(struct device *dev, void *data) PAGE_SIZE - offs, "%s:%s:%s\n", c->pipe0.comp->name, - dev_name(&iface->dev), + dev_name(iface->dev), dev_name(&c->dev)); } if (c->pipe1.comp) { @@ -492,7 +484,7 @@ static int print_links(struct device *dev, void *data) PAGE_SIZE - offs, "%s:%s:%s\n", c->pipe1.comp->name, - dev_name(&iface->dev), + dev_name(iface->dev), dev_name(&c->dev)); } } @@ -500,20 +492,33 @@ static int print_links(struct device *dev, void *data) return 0; } +static int most_match(struct device *dev, struct device_driver *drv) +{ + if (!strcmp(dev_name(dev), "most")) + return 0; + else + return 1; +} + +static struct bus_type mostbus = { + .name = "most", + .match = most_match, +}; + static ssize_t links_show(struct device_driver *drv, char *buf) { struct show_links_data d = { .buf = buf }; - bus_for_each_dev(&mc.bus, NULL, &d, print_links); + bus_for_each_dev(&mostbus, NULL, &d, print_links); return d.offs; } static ssize_t components_show(struct device_driver *drv, char *buf) { - struct core_component *comp; + struct most_component *comp; int offs = 0; - list_for_each_entry(comp, &mc.comp_list, list) { + list_for_each_entry(comp, &comp_list, list) { offs += snprintf(buf + offs, PAGE_SIZE - offs, "%s\n", comp->name); } @@ -531,10 +536,11 @@ static struct most_channel *get_channel(char *mdev, char *mdev_ch) struct most_interface *iface; struct most_channel *c, *tmp; - dev = bus_find_device_by_name(&mc.bus, NULL, mdev); + dev = bus_find_device_by_name(&mostbus, NULL, mdev); if (!dev) return NULL; - iface = to_most_interface(dev); + put_device(dev); + iface = dev_get_drvdata(dev); list_for_each_entry_safe(c, tmp, &iface->p->channel_list, list) { if (!strcmp(dev_name(&c->dev), mdev_ch)) return c; @@ -544,12 +550,12 @@ static struct most_channel *get_channel(char *mdev, char *mdev_ch) static inline int link_channel_to_component(struct most_channel *c, - struct core_component *comp, + struct most_component *comp, char *name, char *comp_param) { int ret; - struct core_component **comp_ptr; + struct most_component **comp_ptr; if (!c->pipe0.comp) comp_ptr = &c->pipe0.comp; @@ -623,7 +629,7 @@ int most_set_cfg_datatype(char *mdev, char *mdev_ch, char *buf) } if (i == ARRAY_SIZE(ch_data_type)) - pr_info("WARN: invalid attribute settings\n"); + dev_warn(&c->dev, "Invalid attribute settings\n"); return 0; } @@ -642,7 +648,7 @@ int most_set_cfg_direction(char *mdev, char *mdev_ch, char *buf) } else if (!strcmp(buf, "tx")) { c->cfg.direction = MOST_CH_TX; } else { - pr_info("Invalid direction\n"); + dev_err(&c->dev, "Invalid direction\n"); return -ENODATA; } return 0; @@ -660,7 +666,7 @@ int most_set_cfg_packets_xact(char *mdev, char *mdev_ch, u16 val) int most_cfg_complete(char *comp_name) { - struct core_component *comp; + struct most_component *comp; comp = match_component(comp_name); if (!comp) @@ -673,7 +679,7 @@ int most_add_link(char *mdev, char *mdev_ch, char *comp_name, char *link_name, char *comp_param) { struct most_channel *c = get_channel(mdev, mdev_ch); - struct core_component *comp = match_component(comp_name); + struct most_component *comp = match_component(comp_name); if (!c || !comp) return -ENODEV; @@ -684,7 +690,7 @@ int most_add_link(char *mdev, char *mdev_ch, char *comp_name, char *link_name, int most_remove_link(char *mdev, char *mdev_ch, char *comp_name) { struct most_channel *c; - struct core_component *comp; + struct most_component *comp; comp = match_component(comp_name); if (!comp) @@ -722,13 +728,11 @@ static const struct attribute_group *mc_attr_groups[] = { NULL, }; -static int most_match(struct device *dev, struct device_driver *drv) -{ - if (!strcmp(dev_name(dev), "most")) - return 0; - else - return 1; -} +static struct device_driver mostbus_driver = { + .name = "most_core", + .bus = &mostbus, + .groups = mc_attr_groups, +}; static inline void trash_mbo(struct mbo *mbo) { @@ -795,7 +799,7 @@ static int hdm_enqueue_thread(void *data) mutex_unlock(&c->nq_mutex); if (unlikely(ret)) { - pr_err("hdm enqueue failed\n"); + dev_err(&c->dev, "Buffer enqueue failed\n"); nq_hdm_mbo(mbo); c->hdm_enqueue_task = NULL; return 0; @@ -922,7 +926,7 @@ flush_fifos: void most_submit_mbo(struct mbo *mbo) { if (WARN_ONCE(!mbo || !mbo->context, - "bad mbo or missing channel reference\n")) + "Bad buffer or missing channel reference\n")) return; nq_hdm_mbo(mbo); @@ -941,8 +945,6 @@ static void most_write_completion(struct mbo *mbo) struct most_channel *c; c = mbo->context; - if (mbo->status == MBO_E_INVAL) - pr_info("WARN: Tx MBO status: invalid\n"); if (unlikely(c->is_poisoned || (mbo->status == MBO_E_CLOSE))) trash_mbo(mbo); else @@ -950,7 +952,7 @@ static void most_write_completion(struct mbo *mbo) } int channel_has_mbo(struct most_interface *iface, int id, - struct core_component *comp) + struct most_component *comp) { struct most_channel *c = iface->p->channel[id]; unsigned long flags; @@ -981,7 +983,7 @@ EXPORT_SYMBOL_GPL(channel_has_mbo); * Returns a pointer to MBO on success or NULL otherwise. */ struct mbo *most_get_mbo(struct most_interface *iface, int id, - struct core_component *comp) + struct most_component *comp) { struct mbo *mbo; struct most_channel *c; @@ -1087,7 +1089,7 @@ static void most_read_completion(struct mbo *mbo) * Returns 0 on success or error code otherwise. */ int most_start_channel(struct most_interface *iface, int id, - struct core_component *comp) + struct most_component *comp) { int num_buffer; int ret; @@ -1101,14 +1103,14 @@ int most_start_channel(struct most_interface *iface, int id, goto out; /* already started by another component */ if (!try_module_get(iface->mod)) { - pr_info("failed to acquire HDM lock\n"); + dev_err(&c->dev, "Failed to acquire HDM lock\n"); mutex_unlock(&c->start_mutex); return -ENOLCK; } c->cfg.extra_len = 0; if (c->iface->configure(c->iface, c->channel_id, &c->cfg)) { - pr_info("channel configuration failed. Go check settings...\n"); + dev_err(&c->dev, "Channel configuration failed. Go check settings...\n"); ret = -EINVAL; goto err_put_module; } @@ -1157,7 +1159,7 @@ EXPORT_SYMBOL_GPL(most_start_channel); * @comp: driver component */ int most_stop_channel(struct most_interface *iface, int id, - struct core_component *comp) + struct most_component *comp) { struct most_channel *c; @@ -1182,8 +1184,8 @@ int most_stop_channel(struct most_interface *iface, int id, c->is_poisoned = true; if (c->iface->poison_channel(c->iface, c->channel_id)) { - pr_err("Cannot stop channel %d of mdev %s\n", c->channel_id, - c->iface->description); + dev_err(&c->dev, "Failed to stop channel %d of interface %s\n", c->channel_id, + c->iface->description); mutex_unlock(&c->start_mutex); return -EAGAIN; } @@ -1192,7 +1194,7 @@ int most_stop_channel(struct most_interface *iface, int id, #ifdef CMPL_INTERRUPTIBLE if (wait_for_completion_interruptible(&c->cleanup)) { - pr_info("Interrupted while clean up ch %d\n", c->channel_id); + dev_err(&c->dev, "Interrupted while cleaning up channel %d\n", c->channel_id); mutex_unlock(&c->start_mutex); return -EINTR; } @@ -1215,14 +1217,13 @@ EXPORT_SYMBOL_GPL(most_stop_channel); * most_register_component - registers a driver component with the core * @comp: driver component */ -int most_register_component(struct core_component *comp) +int most_register_component(struct most_component *comp) { if (!comp) { pr_err("Bad component\n"); return -EINVAL; } - list_add_tail(&comp->list, &mc.comp_list); - pr_info("registered new core component %s\n", comp->name); + list_add_tail(&comp->list, &comp_list); return 0; } EXPORT_SYMBOL_GPL(most_register_component); @@ -1231,9 +1232,9 @@ static int disconnect_channels(struct device *dev, void *data) { struct most_interface *iface; struct most_channel *c, *tmp; - struct core_component *comp = data; + struct most_component *comp = data; - iface = to_most_interface(dev); + iface = dev_get_drvdata(dev); list_for_each_entry_safe(c, tmp, &iface->p->channel_list, list) { if (c->pipe0.comp == comp || c->pipe1.comp == comp) comp->disconnect_channel(c->iface, c->channel_id); @@ -1249,28 +1250,24 @@ static int disconnect_channels(struct device *dev, void *data) * most_deregister_component - deregisters a driver component with the core * @comp: driver component */ -int most_deregister_component(struct core_component *comp) +int most_deregister_component(struct most_component *comp) { if (!comp) { pr_err("Bad component\n"); return -EINVAL; } - bus_for_each_dev(&mc.bus, NULL, comp, disconnect_channels); + bus_for_each_dev(&mostbus, NULL, comp, disconnect_channels); list_del(&comp->list); - pr_info("deregistering component %s\n", comp->name); return 0; } EXPORT_SYMBOL_GPL(most_deregister_component); -static void release_interface(struct device *dev) -{ - pr_info("releasing interface dev %s...\n", dev_name(dev)); -} - static void release_channel(struct device *dev) { - pr_info("releasing channel dev %s...\n", dev_name(dev)); + struct most_channel *c = to_channel(dev); + + kfree(c); } /** @@ -1288,13 +1285,13 @@ int most_register_interface(struct most_interface *iface) if (!iface || !iface->enqueue || !iface->configure || !iface->poison_channel || (iface->num_channels > MAX_CHANNELS)) { - pr_err("Bad interface or channel overflow\n"); + dev_err(iface->dev, "Bad interface or channel overflow\n"); return -EINVAL; } id = ida_simple_get(&mdev_id, 0, 0, GFP_KERNEL); if (id < 0) { - pr_info("Failed to alloc mdev ID\n"); + dev_err(iface->dev, "Failed to allocate device ID\n"); return id; } @@ -1307,14 +1304,13 @@ int most_register_interface(struct most_interface *iface) INIT_LIST_HEAD(&iface->p->channel_list); iface->p->dev_id = id; strscpy(iface->p->name, iface->description, sizeof(iface->p->name)); - iface->dev.init_name = iface->p->name; - iface->dev.bus = &mc.bus; - iface->dev.parent = &mc.dev; - iface->dev.groups = interface_attr_groups; - iface->dev.release = release_interface; - if (device_register(&iface->dev)) { - pr_err("registering iface->dev failed\n"); + iface->dev->bus = &mostbus; + iface->dev->groups = interface_attr_groups; + dev_set_drvdata(iface->dev, iface); + if (device_register(iface->dev)) { + dev_err(iface->dev, "Failed to register interface device\n"); kfree(iface->p); + put_device(iface->dev); ida_simple_remove(&mdev_id, id); return -ENOMEM; } @@ -1330,7 +1326,7 @@ int most_register_interface(struct most_interface *iface) else snprintf(c->name, STRING_SIZE, "%s", name_suffix); c->dev.init_name = c->name; - c->dev.parent = &iface->dev; + c->dev.parent = iface->dev; c->dev.groups = channel_attr_groups; c->dev.release = release_channel; iface->p->channel[i] = c; @@ -1356,26 +1352,23 @@ int most_register_interface(struct most_interface *iface) mutex_init(&c->nq_mutex); list_add_tail(&c->list, &iface->p->channel_list); if (device_register(&c->dev)) { - pr_err("registering c->dev failed\n"); + dev_err(&c->dev, "Failed to register channel device\n"); goto err_free_most_channel; } } - pr_info("registered new device mdev%d (%s)\n", - id, iface->description); most_interface_register_notify(iface->description); return 0; err_free_most_channel: - kfree(c); + put_device(&c->dev); err_free_resources: while (i > 0) { c = iface->p->channel[--i]; device_unregister(&c->dev); - kfree(c); } kfree(iface->p); - device_unregister(&iface->dev); + device_unregister(iface->dev); ida_simple_remove(&mdev_id, id); return -ENOMEM; } @@ -1393,8 +1386,6 @@ void most_deregister_interface(struct most_interface *iface) int i; struct most_channel *c; - pr_info("deregistering device %s (%s)\n", dev_name(&iface->dev), - iface->description); for (i = 0; i < iface->num_channels; i++) { c = iface->p->channel[i]; if (c->pipe0.comp) @@ -1407,12 +1398,11 @@ void most_deregister_interface(struct most_interface *iface) c->pipe1.comp = NULL; list_del(&c->list); device_unregister(&c->dev); - kfree(c); } ida_simple_remove(&mdev_id, iface->p->dev_id); kfree(iface->p); - device_unregister(&iface->dev); + device_unregister(iface->dev); } EXPORT_SYMBOL_GPL(most_deregister_interface); @@ -1462,57 +1452,35 @@ void most_resume_enqueue(struct most_interface *iface, int id) } EXPORT_SYMBOL_GPL(most_resume_enqueue); -static void release_most_sub(struct device *dev) -{ - pr_info("releasing most_subsystem\n"); -} - static int __init most_init(void) { int err; - pr_info("init()\n"); - INIT_LIST_HEAD(&mc.comp_list); + INIT_LIST_HEAD(&comp_list); ida_init(&mdev_id); - mc.bus.name = "most", - mc.bus.match = most_match, - mc.drv.name = "most_core", - mc.drv.bus = &mc.bus, - mc.drv.groups = mc_attr_groups; - - err = bus_register(&mc.bus); + err = bus_register(&mostbus); if (err) { - pr_info("Cannot register most bus\n"); + pr_err("Failed to register most bus\n"); return err; } - err = driver_register(&mc.drv); + err = driver_register(&mostbus_driver); if (err) { - pr_info("Cannot register core driver\n"); + pr_err("Failed to register core driver\n"); goto err_unregister_bus; } - mc.dev.init_name = "most_bus"; - mc.dev.release = release_most_sub; - if (device_register(&mc.dev)) { - err = -ENOMEM; - goto err_unregister_driver; - } configfs_init(); return 0; -err_unregister_driver: - driver_unregister(&mc.drv); err_unregister_bus: - bus_unregister(&mc.bus); + bus_unregister(&mostbus); return err; } static void __exit most_exit(void) { - pr_info("exit core module\n"); - device_unregister(&mc.dev); - driver_unregister(&mc.drv); - bus_unregister(&mc.bus); + driver_unregister(&mostbus_driver); + bus_unregister(&mostbus); ida_destroy(&mdev_id); } diff --git a/drivers/staging/most/dim2/Makefile b/drivers/staging/most/dim2/Makefile index 116f04d69244..861adacf6c72 100644 --- a/drivers/staging/most/dim2/Makefile +++ b/drivers/staging/most/dim2/Makefile @@ -2,4 +2,3 @@ obj-$(CONFIG_MOST_DIM2) += most_dim2.o most_dim2-objs := dim2.o hal.o sysfs.o -ccflags-y += -I $(srctree)/drivers/staging/ diff --git a/drivers/staging/most/dim2/dim2.c b/drivers/staging/most/dim2/dim2.c index 64c979155a49..16593281fcda 100644 --- a/drivers/staging/most/dim2/dim2.c +++ b/drivers/staging/most/dim2/dim2.c @@ -21,7 +21,7 @@ #include <linux/sched.h> #include <linux/kthread.h> -#include "most/core.h" +#include "../most.h" #include "hal.h" #include "errors.h" #include "sysfs.h" @@ -854,8 +854,9 @@ static int dim2_probe(struct platform_device *pdev) dev->most_iface.poison_channel = poison_channel; dev->most_iface.request_netinfo = request_netinfo; dev->most_iface.driver_dev = &pdev->dev; + dev->most_iface.dev = &dev->dev; dev->dev.init_name = "dim2_state"; - dev->dev.parent = &dev->most_iface.dev; + dev->dev.parent = &pdev->dev; ret = most_register_interface(&dev->most_iface); if (ret) { diff --git a/drivers/staging/most/i2c/Makefile b/drivers/staging/most/i2c/Makefile index 2b3769dc19e7..71099dd0f85b 100644 --- a/drivers/staging/most/i2c/Makefile +++ b/drivers/staging/most/i2c/Makefile @@ -2,4 +2,3 @@ obj-$(CONFIG_MOST_I2C) += most_i2c.o most_i2c-objs := i2c.o -ccflags-y += -I $(srctree)/drivers/staging/ diff --git a/drivers/staging/most/i2c/i2c.c b/drivers/staging/most/i2c/i2c.c index 4a4fc1005932..2980f7065846 100644 --- a/drivers/staging/most/i2c/i2c.c +++ b/drivers/staging/most/i2c/i2c.c @@ -14,7 +14,7 @@ #include <linux/interrupt.h> #include <linux/err.h> -#include "most/core.h" +#include "../most.h" enum { CH_RX, CH_TX, NUM_CHANNELS }; diff --git a/drivers/staging/most/core.h b/drivers/staging/most/most.h index 49859aef98df..232e01b7f5d2 100644 --- a/drivers/staging/most/core.h +++ b/drivers/staging/most/most.h @@ -1,4 +1,4 @@ -// SPDX-License-Identifier: GPL-2.0 +/* SPDX-License-Identifier: GPL-2.0 */ /* * most.h - API for component and adapter drivers * @@ -47,7 +47,7 @@ enum most_channel_data_type { MOST_CH_SYNC = 1 << 5, }; -enum mbo_status_flags { +enum most_status_flags { /* MBO was processed successfully (data was send or received )*/ MBO_SUCCESS = 0, /* The MBO contains wrong or missing information. */ @@ -184,7 +184,7 @@ struct mbo { dma_addr_t bus_address; u16 buffer_length; u16 processed_length; - enum mbo_status_flags status; + enum most_status_flags status; void (*complete)(struct mbo *mbo); }; @@ -229,7 +229,7 @@ struct mbo { * @priv Private field used by mostcore to store context information. */ struct most_interface { - struct device dev; + struct device *dev; struct device *driver_dev; struct module *mod; enum most_interface_type interface; @@ -251,10 +251,8 @@ struct most_interface { struct interface_private *p; }; -#define to_most_interface(d) container_of(d, struct most_interface, dev) - /** - * struct core_component - identifies a loadable component for the mostcore + * struct most_component - identifies a loadable component for the mostcore * @list: list_head * @name: component name * @probe_channel: function for core to notify driver about channel connection @@ -262,7 +260,7 @@ struct most_interface { * @rx_completion: completion handler for received packets * @tx_completion: completion handler for transmitted packets */ -struct core_component { +struct most_component { struct list_head list; const char *name; struct module *mod; @@ -310,20 +308,20 @@ void most_stop_enqueue(struct most_interface *iface, int channel_idx); * in wait fifo. */ void most_resume_enqueue(struct most_interface *iface, int channel_idx); -int most_register_component(struct core_component *comp); -int most_deregister_component(struct core_component *comp); +int most_register_component(struct most_component *comp); +int most_deregister_component(struct most_component *comp); struct mbo *most_get_mbo(struct most_interface *iface, int channel_idx, - struct core_component *comp); + struct most_component *comp); void most_put_mbo(struct mbo *mbo); int channel_has_mbo(struct most_interface *iface, int channel_idx, - struct core_component *comp); + struct most_component *comp); int most_start_channel(struct most_interface *iface, int channel_idx, - struct core_component *comp); + struct most_component *comp); int most_stop_channel(struct most_interface *iface, int channel_idx, - struct core_component *comp); + struct most_component *comp); int __init configfs_init(void); -int most_register_configfs_subsys(struct core_component *comp); -void most_deregister_configfs_subsys(struct core_component *comp); +int most_register_configfs_subsys(struct most_component *comp); +void most_deregister_configfs_subsys(struct most_component *comp); int most_add_link(char *mdev, char *mdev_ch, char *comp_name, char *link_name, char *comp_param); int most_remove_link(char *mdev, char *mdev_ch, char *comp_name); diff --git a/drivers/staging/most/net/Makefile b/drivers/staging/most/net/Makefile index f0ac64dee71b..1582c97eb204 100644 --- a/drivers/staging/most/net/Makefile +++ b/drivers/staging/most/net/Makefile @@ -2,4 +2,3 @@ obj-$(CONFIG_MOST_NET) += most_net.o most_net-objs := net.o -ccflags-y += -I $(srctree)/drivers/staging/ diff --git a/drivers/staging/most/net/net.c b/drivers/staging/most/net/net.c index 6cab1bb8956e..5547e36e09de 100644 --- a/drivers/staging/most/net/net.c +++ b/drivers/staging/most/net/net.c @@ -15,7 +15,8 @@ #include <linux/list.h> #include <linux/wait.h> #include <linux/kobject.h> -#include "most/core.h" + +#include "../most.h" #define MEP_HDR_LEN 8 #define MDP_HDR_LEN 16 @@ -70,7 +71,7 @@ struct net_dev_context { static struct list_head net_devices = LIST_HEAD_INIT(net_devices); static struct mutex probe_disc_mt; /* ch->linked = true, most_nd_open */ static DEFINE_SPINLOCK(list_lock); /* list_head, ch->linked = false, dev_hold */ -static struct core_component comp; +static struct most_component comp; static int skb_to_mamac(const struct sk_buff *skb, struct mbo *mbo) { @@ -81,6 +82,11 @@ static int skb_to_mamac(const struct sk_buff *skb, struct mbo *mbo) unsigned int payload_len = skb->len - ETH_HLEN; unsigned int mdp_len = payload_len + MDP_HDR_LEN; + if (mdp_len < skb->len) { + pr_err("drop: too large packet! (%u)\n", skb->len); + return -EINVAL; + } + if (mbo->buffer_length < mdp_len) { pr_err("drop: too small buffer! (%d for %d)\n", mbo->buffer_length, mdp_len); @@ -128,6 +134,11 @@ static int skb_to_mep(const struct sk_buff *skb, struct mbo *mbo) u8 *buff = mbo->virt_address; unsigned int mep_len = skb->len + MEP_HDR_LEN; + if (mep_len < skb->len) { + pr_err("drop: too large packet! (%u)\n", skb->len); + return -EINVAL; + } + if (mbo->buffer_length < mep_len) { pr_err("drop: too small buffer! (%d for %d)\n", mbo->buffer_length, mep_len); @@ -497,7 +508,7 @@ put_nd: return ret; } -static struct core_component comp = { +static struct most_component comp = { .mod = THIS_MODULE, .name = "net", .probe_channel = comp_probe_channel, diff --git a/drivers/staging/most/sound/Makefile b/drivers/staging/most/sound/Makefile index a3d086c6ca70..f0cd9d8d213e 100644 --- a/drivers/staging/most/sound/Makefile +++ b/drivers/staging/most/sound/Makefile @@ -2,4 +2,3 @@ obj-$(CONFIG_MOST_SOUND) += most_sound.o most_sound-objs := sound.o -ccflags-y += -I $(srctree)/drivers/staging/ diff --git a/drivers/staging/most/sound/sound.c b/drivers/staging/most/sound/sound.c index 723d0bd1cc21..44cf2334834f 100644 --- a/drivers/staging/most/sound/sound.c +++ b/drivers/staging/most/sound/sound.c @@ -17,12 +17,13 @@ #include <sound/pcm_params.h> #include <linux/sched.h> #include <linux/kthread.h> -#include <most/core.h> + +#include "../most.h" #define DRIVER_NAME "sound" #define STRING_SIZE 80 -static struct core_component comp; +static struct most_component comp; /** * struct channel - private structure to keep channel specific data @@ -323,45 +324,6 @@ static int pcm_close(struct snd_pcm_substream *substream) } /** - * pcm_hw_params - implements hw_params callback function for PCM middle layer - * @substream: sub-stream pointer - * @hw_params: contains the hardware parameters set by the application - * - * This is called when the hardware parameters is set by the application, that - * is, once when the buffer size, the period size, the format, etc. are defined - * for the PCM substream. Many hardware setups should be done is this callback, - * including the allocation of buffers. - * - * Returns 0 on success or error code otherwise. - */ -static int pcm_hw_params(struct snd_pcm_substream *substream, - struct snd_pcm_hw_params *hw_params) -{ - struct channel *channel = substream->private_data; - - if ((params_channels(hw_params) > channel->pcm_hardware.channels_max) || - (params_channels(hw_params) < channel->pcm_hardware.channels_min)) { - pr_err("Requested number of channels not supported.\n"); - return -EINVAL; - } - return snd_pcm_lib_malloc_pages(substream, params_buffer_bytes(hw_params)); -} - -/** - * pcm_hw_free - implements hw_free callback function for PCM middle layer - * @substream: substream pointer - * - * This is called to release the resources allocated via hw_params. - * This function will be always called before the close callback is called. - * - * Returns 0 on success or error code otherwise. - */ -static int pcm_hw_free(struct snd_pcm_substream *substream) -{ - return snd_pcm_lib_free_pages(substream); -} - -/** * pcm_prepare - implements prepare callback function for PCM middle layer * @substream: substream pointer * @@ -462,9 +424,6 @@ static snd_pcm_uframes_t pcm_pointer(struct snd_pcm_substream *substream) static const struct snd_pcm_ops pcm_ops = { .open = pcm_open, .close = pcm_close, - .ioctl = snd_pcm_lib_ioctl, - .hw_params = pcm_hw_params, - .hw_free = pcm_hw_free, .prepare = pcm_prepare, .trigger = pcm_trigger, .pointer = pcm_pointer, @@ -661,8 +620,7 @@ skip_adpt_alloc: pcm->private_data = channel; strscpy(pcm->name, device_name, sizeof(pcm->name)); snd_pcm_set_ops(pcm, direction, &pcm_ops); - snd_pcm_lib_preallocate_pages_for_all(pcm, SNDRV_DMA_TYPE_VMALLOC, - NULL, 0, 0); + snd_pcm_set_managed_buffer_all(pcm, SNDRV_DMA_TYPE_VMALLOC, NULL, 0, 0); return 0; @@ -779,9 +737,9 @@ static int audio_tx_completion(struct most_interface *iface, int channel_id) } /** - * Initialization of the struct core_component + * Initialization of the struct most_component */ -static struct core_component comp = { +static struct most_component comp = { .mod = THIS_MODULE, .name = DRIVER_NAME, .probe_channel = audio_probe_channel, diff --git a/drivers/staging/most/usb/Makefile b/drivers/staging/most/usb/Makefile index 83cf2ead7122..c2b207339aec 100644 --- a/drivers/staging/most/usb/Makefile +++ b/drivers/staging/most/usb/Makefile @@ -2,4 +2,3 @@ obj-$(CONFIG_MOST_USB) += most_usb.o most_usb-objs := usb.o -ccflags-y += -I $(srctree)/drivers/staging/ diff --git a/drivers/staging/most/usb/usb.c b/drivers/staging/most/usb/usb.c index 360cb5b7a10b..0bda88c4bc89 100644 --- a/drivers/staging/most/usb/usb.c +++ b/drivers/staging/most/usb/usb.c @@ -23,7 +23,8 @@ #include <linux/dma-mapping.h> #include <linux/etherdevice.h> #include <linux/uaccess.h> -#include "most/core.h" + +#include "../most.h" #define USB_MTU 512 #define NO_ISOCHRONOUS_URB 0 @@ -101,6 +102,7 @@ struct clear_hold_work { * @poll_work_obj: work for polling link status */ struct most_dev { + struct device dev; struct usb_device *usb_device; struct most_interface iface; struct most_channel_capability *cap; @@ -122,6 +124,7 @@ struct most_dev { }; #define to_mdev(d) container_of(d, struct most_dev, iface) +#define to_mdev_from_dev(d) container_of(d, struct most_dev, dev) #define to_mdev_from_work(w) container_of(w, struct most_dev, poll_work_obj) static void wq_clear_halt(struct work_struct *wq_obj); @@ -1022,6 +1025,12 @@ static void release_dci(struct device *dev) kfree(dci); } +static void release_mdev(struct device *dev) +{ + struct most_dev *mdev = to_mdev_from_dev(dev); + + kfree(mdev); +} /** * hdm_probe - probe function of USB device driver * @interface: Interface of the attached USB device @@ -1060,6 +1069,7 @@ hdm_probe(struct usb_interface *interface, const struct usb_device_id *id) mdev->link_stat_timer.expires = jiffies + (2 * HZ); mdev->iface.mod = hdm_usb_fops.owner; + mdev->iface.dev = &mdev->dev; mdev->iface.driver_dev = &interface->dev; mdev->iface.interface = ITYPE_USB; mdev->iface.configure = hdm_configure_channel; @@ -1078,6 +1088,9 @@ hdm_probe(struct usb_interface *interface, const struct usb_device_id *id) usb_dev->config->desc.bConfigurationValue, usb_iface_desc->desc.bInterfaceNumber); + mdev->dev.init_name = mdev->description; + mdev->dev.parent = &interface->dev; + mdev->dev.release = release_mdev; mdev->conf = kcalloc(num_endpoints, sizeof(*mdev->conf), GFP_KERNEL); if (!mdev->conf) goto err_free_mdev; @@ -1151,7 +1164,7 @@ hdm_probe(struct usb_interface *interface, const struct usb_device_id *id) } mdev->dci->dev.init_name = "dci"; - mdev->dci->dev.parent = &mdev->iface.dev; + mdev->dci->dev.parent = get_device(mdev->iface.dev); mdev->dci->dev.groups = dci_attr_groups; mdev->dci->dev.release = release_dci; if (device_register(&mdev->dci->dev)) { @@ -1165,7 +1178,7 @@ hdm_probe(struct usb_interface *interface, const struct usb_device_id *id) mutex_unlock(&mdev->io_mutex); return 0; err_free_dci: - kfree(mdev->dci); + put_device(&mdev->dci->dev); err_free_busy_urbs: kfree(mdev->busy_urbs); err_free_ep_address: @@ -1175,7 +1188,7 @@ err_free_cap: err_free_conf: kfree(mdev->conf); err_free_mdev: - kfree(mdev); + put_device(&mdev->dev); err_out_of_memory: if (ret == 0 || ret == -ENOMEM) { ret = -ENOMEM; @@ -1205,14 +1218,15 @@ static void hdm_disconnect(struct usb_interface *interface) del_timer_sync(&mdev->link_stat_timer); cancel_work_sync(&mdev->poll_work_obj); - device_unregister(&mdev->dci->dev); + if (mdev->dci) + device_unregister(&mdev->dci->dev); most_deregister_interface(&mdev->iface); kfree(mdev->busy_urbs); kfree(mdev->cap); kfree(mdev->conf); kfree(mdev->ep_address); - kfree(mdev); + put_device(&mdev->dev); } static struct usb_driver hdm_usb = { diff --git a/drivers/staging/most/video/Makefile b/drivers/staging/most/video/Makefile index 2d857d3cbcc8..856175fec8b6 100644 --- a/drivers/staging/most/video/Makefile +++ b/drivers/staging/most/video/Makefile @@ -2,4 +2,3 @@ obj-$(CONFIG_MOST_VIDEO) += most_video.o most_video-objs := video.o -ccflags-y += -I $(srctree)/drivers/staging/ diff --git a/drivers/staging/most/video/video.c b/drivers/staging/most/video/video.c index 10c1ef7e3a3e..d32ae49d617b 100644 --- a/drivers/staging/most/video/video.c +++ b/drivers/staging/most/video/video.c @@ -21,11 +21,11 @@ #include <media/v4l2-ctrls.h> #include <media/v4l2-fh.h> -#include "most/core.h" +#include "../most.h" #define V4L2_CMP_MAX_INPUT 1 -static struct core_component comp; +static struct most_component comp; struct most_video_dev { struct most_interface *iface; @@ -527,7 +527,7 @@ static int comp_disconnect_channel(struct most_interface *iface, return 0; } -static struct core_component comp = { +static struct most_component comp = { .mod = THIS_MODULE, .name = "video", .probe_channel = comp_probe_channel, diff --git a/drivers/staging/mt7621-dts/mt7621.dtsi b/drivers/staging/mt7621-dts/mt7621.dtsi index a4c08110094b..d89d68ffa7bc 100644 --- a/drivers/staging/mt7621-dts/mt7621.dtsi +++ b/drivers/staging/mt7621-dts/mt7621.dtsi @@ -138,7 +138,7 @@ memc: memc@5000 { compatible = "mtk,mt7621-memc"; - reg = <0x300 0x100>; + reg = <0x5000 0x1000>; }; cpc: cpc@1fbf0000 { diff --git a/drivers/staging/nvec/nvec_kbd.c b/drivers/staging/nvec/nvec_kbd.c index 01dbb66f7e9a..386d619e3ee9 100644 --- a/drivers/staging/nvec/nvec_kbd.c +++ b/drivers/staging/nvec/nvec_kbd.c @@ -123,6 +123,8 @@ static int nvec_kbd_probe(struct platform_device *pdev) keycodes[j++] = extcode_tab_us102[i]; idev = devm_input_allocate_device(&pdev->dev); + if (!idev) + return -ENOMEM; idev->name = "nvec keyboard"; idev->phys = "nvec"; idev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_REP) | BIT_MASK(EV_LED); diff --git a/drivers/staging/octeon-usb/Kconfig b/drivers/staging/octeon-usb/Kconfig deleted file mode 100644 index 6a5d842ee0f2..000000000000 --- a/drivers/staging/octeon-usb/Kconfig +++ /dev/null @@ -1,11 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0 -config OCTEON_USB - tristate "Cavium Networks Octeon USB support" - depends on CAVIUM_OCTEON_SOC && USB - help - This driver supports USB host controller on some Cavium - Networks' products in the Octeon family. - - To compile this driver as a module, choose M here. The module - will be called octeon-hcd. - diff --git a/drivers/staging/octeon-usb/Makefile b/drivers/staging/octeon-usb/Makefile deleted file mode 100644 index 9873a0130ad5..000000000000 --- a/drivers/staging/octeon-usb/Makefile +++ /dev/null @@ -1,2 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0 -obj-${CONFIG_OCTEON_USB} := octeon-hcd.o diff --git a/drivers/staging/octeon-usb/TODO b/drivers/staging/octeon-usb/TODO deleted file mode 100644 index 2b29acca5caa..000000000000 --- a/drivers/staging/octeon-usb/TODO +++ /dev/null @@ -1,8 +0,0 @@ -This driver is functional and has been tested on EdgeRouter Lite, -D-Link DSR-1000N and EBH5600 evaluation board with USB mass storage. - -TODO: - - kernel coding style - - checkpatch warnings - -Contact: Aaro Koskinen <aaro.koskinen@iki.fi> diff --git a/drivers/staging/octeon-usb/octeon-hcd.c b/drivers/staging/octeon-usb/octeon-hcd.c deleted file mode 100644 index 582c9187559d..000000000000 --- a/drivers/staging/octeon-usb/octeon-hcd.c +++ /dev/null @@ -1,3737 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * - * Copyright (C) 2008 Cavium Networks - * - * Some parts of the code were originally released under BSD license: - * - * Copyright (c) 2003-2010 Cavium Networks (support@cavium.com). All rights - * reserved. - * - * Redistribution and use in source and binary forms, with or without - * modification, are permitted provided that the following conditions are - * met: - * - * * Redistributions of source code must retain the above copyright - * notice, this list of conditions and the following disclaimer. - * - * * Redistributions in binary form must reproduce the above - * copyright notice, this list of conditions and the following - * disclaimer in the documentation and/or other materials provided - * with the distribution. - * - * * Neither the name of Cavium Networks nor the names of - * its contributors may be used to endorse or promote products - * derived from this software without specific prior written - * permission. - * - * This Software, including technical data, may be subject to U.S. export - * control laws, including the U.S. Export Administration Act and its associated - * regulations, and may be subject to export or import regulations in other - * countries. - * - * TO THE MAXIMUM EXTENT PERMITTED BY LAW, THE SOFTWARE IS PROVIDED "AS IS" - * AND WITH ALL FAULTS AND CAVIUM NETWORKS MAKES NO PROMISES, REPRESENTATIONS OR - * WARRANTIES, EITHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, WITH RESPECT TO - * THE SOFTWARE, INCLUDING ITS CONDITION, ITS CONFORMITY TO ANY REPRESENTATION - * OR DESCRIPTION, OR THE EXISTENCE OF ANY LATENT OR PATENT DEFECTS, AND CAVIUM - * SPECIFICALLY DISCLAIMS ALL IMPLIED (IF ANY) WARRANTIES OF TITLE, - * MERCHANTABILITY, NONINFRINGEMENT, FITNESS FOR A PARTICULAR PURPOSE, LACK OF - * VIRUSES, ACCURACY OR COMPLETENESS, QUIET ENJOYMENT, QUIET POSSESSION OR - * CORRESPONDENCE TO DESCRIPTION. THE ENTIRE RISK ARISING OUT OF USE OR - * PERFORMANCE OF THE SOFTWARE LIES WITH YOU. - */ - -#include <linux/usb.h> -#include <linux/slab.h> -#include <linux/module.h> -#include <linux/usb/hcd.h> -#include <linux/prefetch.h> -#include <linux/dma-mapping.h> -#include <linux/platform_device.h> - -#include <asm/octeon/octeon.h> - -#include "octeon-hcd.h" - -/** - * enum cvmx_usb_speed - the possible USB device speeds - * - * @CVMX_USB_SPEED_HIGH: Device is operation at 480Mbps - * @CVMX_USB_SPEED_FULL: Device is operation at 12Mbps - * @CVMX_USB_SPEED_LOW: Device is operation at 1.5Mbps - */ -enum cvmx_usb_speed { - CVMX_USB_SPEED_HIGH = 0, - CVMX_USB_SPEED_FULL = 1, - CVMX_USB_SPEED_LOW = 2, -}; - -/** - * enum cvmx_usb_transfer - the possible USB transfer types - * - * @CVMX_USB_TRANSFER_CONTROL: USB transfer type control for hub and status - * transfers - * @CVMX_USB_TRANSFER_ISOCHRONOUS: USB transfer type isochronous for low - * priority periodic transfers - * @CVMX_USB_TRANSFER_BULK: USB transfer type bulk for large low priority - * transfers - * @CVMX_USB_TRANSFER_INTERRUPT: USB transfer type interrupt for high priority - * periodic transfers - */ -enum cvmx_usb_transfer { - CVMX_USB_TRANSFER_CONTROL = 0, - CVMX_USB_TRANSFER_ISOCHRONOUS = 1, - CVMX_USB_TRANSFER_BULK = 2, - CVMX_USB_TRANSFER_INTERRUPT = 3, -}; - -/** - * enum cvmx_usb_direction - the transfer directions - * - * @CVMX_USB_DIRECTION_OUT: Data is transferring from Octeon to the device/host - * @CVMX_USB_DIRECTION_IN: Data is transferring from the device/host to Octeon - */ -enum cvmx_usb_direction { - CVMX_USB_DIRECTION_OUT, - CVMX_USB_DIRECTION_IN, -}; - -/** - * enum cvmx_usb_status - possible callback function status codes - * - * @CVMX_USB_STATUS_OK: The transaction / operation finished without - * any errors - * @CVMX_USB_STATUS_SHORT: FIXME: This is currently not implemented - * @CVMX_USB_STATUS_CANCEL: The transaction was canceled while in flight - * by a user call to cvmx_usb_cancel - * @CVMX_USB_STATUS_ERROR: The transaction aborted with an unexpected - * error status - * @CVMX_USB_STATUS_STALL: The transaction received a USB STALL response - * from the device - * @CVMX_USB_STATUS_XACTERR: The transaction failed with an error from the - * device even after a number of retries - * @CVMX_USB_STATUS_DATATGLERR: The transaction failed with a data toggle - * error even after a number of retries - * @CVMX_USB_STATUS_BABBLEERR: The transaction failed with a babble error - * @CVMX_USB_STATUS_FRAMEERR: The transaction failed with a frame error - * even after a number of retries - */ -enum cvmx_usb_status { - CVMX_USB_STATUS_OK, - CVMX_USB_STATUS_SHORT, - CVMX_USB_STATUS_CANCEL, - CVMX_USB_STATUS_ERROR, - CVMX_USB_STATUS_STALL, - CVMX_USB_STATUS_XACTERR, - CVMX_USB_STATUS_DATATGLERR, - CVMX_USB_STATUS_BABBLEERR, - CVMX_USB_STATUS_FRAMEERR, -}; - -/** - * struct cvmx_usb_port_status - the USB port status information - * - * @port_enabled: 1 = Usb port is enabled, 0 = disabled - * @port_over_current: 1 = Over current detected, 0 = Over current not - * detected. Octeon doesn't support over current detection. - * @port_powered: 1 = Port power is being supplied to the device, 0 = - * power is off. Octeon doesn't support turning port power - * off. - * @port_speed: Current port speed. - * @connected: 1 = A device is connected to the port, 0 = No device is - * connected. - * @connect_change: 1 = Device connected state changed since the last set - * status call. - */ -struct cvmx_usb_port_status { - u32 reserved : 25; - u32 port_enabled : 1; - u32 port_over_current : 1; - u32 port_powered : 1; - enum cvmx_usb_speed port_speed : 2; - u32 connected : 1; - u32 connect_change : 1; -}; - -/** - * struct cvmx_usb_iso_packet - descriptor for Isochronous packets - * - * @offset: This is the offset in bytes into the main buffer where this data - * is stored. - * @length: This is the length in bytes of the data. - * @status: This is the status of this individual packet transfer. - */ -struct cvmx_usb_iso_packet { - int offset; - int length; - enum cvmx_usb_status status; -}; - -/** - * enum cvmx_usb_initialize_flags - flags used by the initialization function - * - * @CVMX_USB_INITIALIZE_FLAGS_CLOCK_XO_XI: The USB port uses a 12MHz crystal - * as clock source at USB_XO and - * USB_XI. - * @CVMX_USB_INITIALIZE_FLAGS_CLOCK_XO_GND: The USB port uses 12/24/48MHz 2.5V - * board clock source at USB_XO. - * USB_XI should be tied to GND. - * @CVMX_USB_INITIALIZE_FLAGS_CLOCK_MHZ_MASK: Mask for clock speed field - * @CVMX_USB_INITIALIZE_FLAGS_CLOCK_12MHZ: Speed of reference clock or - * crystal - * @CVMX_USB_INITIALIZE_FLAGS_CLOCK_24MHZ: Speed of reference clock - * @CVMX_USB_INITIALIZE_FLAGS_CLOCK_48MHZ: Speed of reference clock - * @CVMX_USB_INITIALIZE_FLAGS_NO_DMA: Disable DMA and used polled IO for - * data transfer use for the USB - */ -enum cvmx_usb_initialize_flags { - CVMX_USB_INITIALIZE_FLAGS_CLOCK_XO_XI = 1 << 0, - CVMX_USB_INITIALIZE_FLAGS_CLOCK_XO_GND = 1 << 1, - CVMX_USB_INITIALIZE_FLAGS_CLOCK_MHZ_MASK = 3 << 3, - CVMX_USB_INITIALIZE_FLAGS_CLOCK_12MHZ = 1 << 3, - CVMX_USB_INITIALIZE_FLAGS_CLOCK_24MHZ = 2 << 3, - CVMX_USB_INITIALIZE_FLAGS_CLOCK_48MHZ = 3 << 3, - /* Bits 3-4 used to encode the clock frequency */ - CVMX_USB_INITIALIZE_FLAGS_NO_DMA = 1 << 5, -}; - -/** - * enum cvmx_usb_pipe_flags - internal flags for a pipe. - * - * @CVMX_USB_PIPE_FLAGS_SCHEDULED: Used internally to determine if a pipe is - * actively using hardware. - * @CVMX_USB_PIPE_FLAGS_NEED_PING: Used internally to determine if a high speed - * pipe is in the ping state. - */ -enum cvmx_usb_pipe_flags { - CVMX_USB_PIPE_FLAGS_SCHEDULED = 1 << 17, - CVMX_USB_PIPE_FLAGS_NEED_PING = 1 << 18, -}; - -/* Maximum number of times to retry failed transactions */ -#define MAX_RETRIES 3 - -/* Maximum number of hardware channels supported by the USB block */ -#define MAX_CHANNELS 8 - -/* - * The low level hardware can transfer a maximum of this number of bytes in each - * transfer. The field is 19 bits wide - */ -#define MAX_TRANSFER_BYTES ((1 << 19) - 1) - -/* - * The low level hardware can transfer a maximum of this number of packets in - * each transfer. The field is 10 bits wide - */ -#define MAX_TRANSFER_PACKETS ((1 << 10) - 1) - -/** - * Logical transactions may take numerous low level - * transactions, especially when splits are concerned. This - * enum represents all of the possible stages a transaction can - * be in. Note that split completes are always even. This is so - * the NAK handler can backup to the previous low level - * transaction with a simple clearing of bit 0. - */ -enum cvmx_usb_stage { - CVMX_USB_STAGE_NON_CONTROL, - CVMX_USB_STAGE_NON_CONTROL_SPLIT_COMPLETE, - CVMX_USB_STAGE_SETUP, - CVMX_USB_STAGE_SETUP_SPLIT_COMPLETE, - CVMX_USB_STAGE_DATA, - CVMX_USB_STAGE_DATA_SPLIT_COMPLETE, - CVMX_USB_STAGE_STATUS, - CVMX_USB_STAGE_STATUS_SPLIT_COMPLETE, -}; - -/** - * struct cvmx_usb_transaction - describes each pending USB transaction - * regardless of type. These are linked together - * to form a list of pending requests for a pipe. - * - * @node: List node for transactions in the pipe. - * @type: Type of transaction, duplicated of the pipe. - * @flags: State flags for this transaction. - * @buffer: User's physical buffer address to read/write. - * @buffer_length: Size of the user's buffer in bytes. - * @control_header: For control transactions, physical address of the 8 - * byte standard header. - * @iso_start_frame: For ISO transactions, the starting frame number. - * @iso_number_packets: For ISO transactions, the number of packets in the - * request. - * @iso_packets: For ISO transactions, the sub packets in the request. - * @actual_bytes: Actual bytes transfer for this transaction. - * @stage: For control transactions, the current stage. - * @urb: URB. - */ -struct cvmx_usb_transaction { - struct list_head node; - enum cvmx_usb_transfer type; - u64 buffer; - int buffer_length; - u64 control_header; - int iso_start_frame; - int iso_number_packets; - struct cvmx_usb_iso_packet *iso_packets; - int xfersize; - int pktcnt; - int retries; - int actual_bytes; - enum cvmx_usb_stage stage; - struct urb *urb; -}; - -/** - * struct cvmx_usb_pipe - a pipe represents a virtual connection between Octeon - * and some USB device. It contains a list of pending - * request to the device. - * - * @node: List node for pipe list - * @next: Pipe after this one in the list - * @transactions: List of pending transactions - * @interval: For periodic pipes, the interval between packets in - * frames - * @next_tx_frame: The next frame this pipe is allowed to transmit on - * @flags: State flags for this pipe - * @device_speed: Speed of device connected to this pipe - * @transfer_type: Type of transaction supported by this pipe - * @transfer_dir: IN or OUT. Ignored for Control - * @multi_count: Max packet in a row for the device - * @max_packet: The device's maximum packet size in bytes - * @device_addr: USB device address at other end of pipe - * @endpoint_num: USB endpoint number at other end of pipe - * @hub_device_addr: Hub address this device is connected to - * @hub_port: Hub port this device is connected to - * @pid_toggle: This toggles between 0/1 on every packet send to track - * the data pid needed - * @channel: Hardware DMA channel for this pipe - * @split_sc_frame: The low order bits of the frame number the split - * complete should be sent on - */ -struct cvmx_usb_pipe { - struct list_head node; - struct list_head transactions; - u64 interval; - u64 next_tx_frame; - enum cvmx_usb_pipe_flags flags; - enum cvmx_usb_speed device_speed; - enum cvmx_usb_transfer transfer_type; - enum cvmx_usb_direction transfer_dir; - int multi_count; - u16 max_packet; - u8 device_addr; - u8 endpoint_num; - u8 hub_device_addr; - u8 hub_port; - u8 pid_toggle; - u8 channel; - s8 split_sc_frame; -}; - -struct cvmx_usb_tx_fifo { - struct { - int channel; - int size; - u64 address; - } entry[MAX_CHANNELS + 1]; - int head; - int tail; -}; - -/** - * struct octeon_hcd - the state of the USB block - * - * lock: Serialization lock. - * init_flags: Flags passed to initialize. - * index: Which USB block this is for. - * idle_hardware_channels: Bit set for every idle hardware channel. - * usbcx_hprt: Stored port status so we don't need to read a CSR to - * determine splits. - * pipe_for_channel: Map channels to pipes. - * pipe: Storage for pipes. - * indent: Used by debug output to indent functions. - * port_status: Last port status used for change notification. - * idle_pipes: List of open pipes that have no transactions. - * active_pipes: Active pipes indexed by transfer type. - * frame_number: Increments every SOF interrupt for time keeping. - * active_split: Points to the current active split, or NULL. - */ -struct octeon_hcd { - spinlock_t lock; /* serialization lock */ - int init_flags; - int index; - int idle_hardware_channels; - union cvmx_usbcx_hprt usbcx_hprt; - struct cvmx_usb_pipe *pipe_for_channel[MAX_CHANNELS]; - int indent; - struct cvmx_usb_port_status port_status; - struct list_head idle_pipes; - struct list_head active_pipes[4]; - u64 frame_number; - struct cvmx_usb_transaction *active_split; - struct cvmx_usb_tx_fifo periodic; - struct cvmx_usb_tx_fifo nonperiodic; -}; - -/* - * This macro logically sets a single field in a CSR. It does the sequence - * read, modify, and write - */ -#define USB_SET_FIELD32(address, _union, field, value) \ - do { \ - union _union c; \ - \ - c.u32 = cvmx_usb_read_csr32(usb, address); \ - c.s.field = value; \ - cvmx_usb_write_csr32(usb, address, c.u32); \ - } while (0) - -/* Returns the IO address to push/pop stuff data from the FIFOs */ -#define USB_FIFO_ADDRESS(channel, usb_index) \ - (CVMX_USBCX_GOTGCTL(usb_index) + ((channel) + 1) * 0x1000) - -/** - * struct octeon_temp_buffer - a bounce buffer for USB transfers - * @orig_buffer: the original buffer passed by the USB stack - * @data: the newly allocated temporary buffer (excluding meta-data) - * - * Both the DMA engine and FIFO mode will always transfer full 32-bit words. If - * the buffer is too short, we need to allocate a temporary one, and this struct - * represents it. - */ -struct octeon_temp_buffer { - void *orig_buffer; - u8 data[0]; -}; - -static inline struct usb_hcd *octeon_to_hcd(struct octeon_hcd *p) -{ - return container_of((void *)p, struct usb_hcd, hcd_priv); -} - -/** - * octeon_alloc_temp_buffer - allocate a temporary buffer for USB transfer - * (if needed) - * @urb: URB. - * @mem_flags: Memory allocation flags. - * - * This function allocates a temporary bounce buffer whenever it's needed - * due to HW limitations. - */ -static int octeon_alloc_temp_buffer(struct urb *urb, gfp_t mem_flags) -{ - struct octeon_temp_buffer *temp; - - if (urb->num_sgs || urb->sg || - (urb->transfer_flags & URB_NO_TRANSFER_DMA_MAP) || - !(urb->transfer_buffer_length % sizeof(u32))) - return 0; - - temp = kmalloc(ALIGN(urb->transfer_buffer_length, sizeof(u32)) + - sizeof(*temp), mem_flags); - if (!temp) - return -ENOMEM; - - temp->orig_buffer = urb->transfer_buffer; - if (usb_urb_dir_out(urb)) - memcpy(temp->data, urb->transfer_buffer, - urb->transfer_buffer_length); - urb->transfer_buffer = temp->data; - urb->transfer_flags |= URB_ALIGNED_TEMP_BUFFER; - - return 0; -} - -/** - * octeon_free_temp_buffer - free a temporary buffer used by USB transfers. - * @urb: URB. - * - * Frees a buffer allocated by octeon_alloc_temp_buffer(). - */ -static void octeon_free_temp_buffer(struct urb *urb) -{ - struct octeon_temp_buffer *temp; - size_t length; - - if (!(urb->transfer_flags & URB_ALIGNED_TEMP_BUFFER)) - return; - - temp = container_of(urb->transfer_buffer, struct octeon_temp_buffer, - data); - if (usb_urb_dir_in(urb)) { - if (usb_pipeisoc(urb->pipe)) - length = urb->transfer_buffer_length; - else - length = urb->actual_length; - - memcpy(temp->orig_buffer, urb->transfer_buffer, length); - } - urb->transfer_buffer = temp->orig_buffer; - urb->transfer_flags &= ~URB_ALIGNED_TEMP_BUFFER; - kfree(temp); -} - -/** - * octeon_map_urb_for_dma - Octeon-specific map_urb_for_dma(). - * @hcd: USB HCD structure. - * @urb: URB. - * @mem_flags: Memory allocation flags. - */ -static int octeon_map_urb_for_dma(struct usb_hcd *hcd, struct urb *urb, - gfp_t mem_flags) -{ - int ret; - - ret = octeon_alloc_temp_buffer(urb, mem_flags); - if (ret) - return ret; - - ret = usb_hcd_map_urb_for_dma(hcd, urb, mem_flags); - if (ret) - octeon_free_temp_buffer(urb); - - return ret; -} - -/** - * octeon_unmap_urb_for_dma - Octeon-specific unmap_urb_for_dma() - * @hcd: USB HCD structure. - * @urb: URB. - */ -static void octeon_unmap_urb_for_dma(struct usb_hcd *hcd, struct urb *urb) -{ - usb_hcd_unmap_urb_for_dma(hcd, urb); - octeon_free_temp_buffer(urb); -} - -/** - * Read a USB 32bit CSR. It performs the necessary address swizzle - * for 32bit CSRs and logs the value in a readable format if - * debugging is on. - * - * @usb: USB block this access is for - * @address: 64bit address to read - * - * Returns: Result of the read - */ -static inline u32 cvmx_usb_read_csr32(struct octeon_hcd *usb, u64 address) -{ - return cvmx_read64_uint32(address ^ 4); -} - -/** - * Write a USB 32bit CSR. It performs the necessary address - * swizzle for 32bit CSRs and logs the value in a readable format - * if debugging is on. - * - * @usb: USB block this access is for - * @address: 64bit address to write - * @value: Value to write - */ -static inline void cvmx_usb_write_csr32(struct octeon_hcd *usb, - u64 address, u32 value) -{ - cvmx_write64_uint32(address ^ 4, value); - cvmx_read64_uint64(CVMX_USBNX_DMA0_INB_CHN0(usb->index)); -} - -/** - * Return non zero if this pipe connects to a non HIGH speed - * device through a high speed hub. - * - * @usb: USB block this access is for - * @pipe: Pipe to check - * - * Returns: Non zero if we need to do split transactions - */ -static inline int cvmx_usb_pipe_needs_split(struct octeon_hcd *usb, - struct cvmx_usb_pipe *pipe) -{ - return pipe->device_speed != CVMX_USB_SPEED_HIGH && - usb->usbcx_hprt.s.prtspd == CVMX_USB_SPEED_HIGH; -} - -/** - * Trivial utility function to return the correct PID for a pipe - * - * @pipe: pipe to check - * - * Returns: PID for pipe - */ -static inline int cvmx_usb_get_data_pid(struct cvmx_usb_pipe *pipe) -{ - if (pipe->pid_toggle) - return 2; /* Data1 */ - return 0; /* Data0 */ -} - -/* Loops through register until txfflsh or rxfflsh become zero.*/ -static int cvmx_wait_tx_rx(struct octeon_hcd *usb, int fflsh_type) -{ - int result; - u64 address = CVMX_USBCX_GRSTCTL(usb->index); - u64 done = cvmx_get_cycle() + 100 * - (u64)octeon_get_clock_rate / 1000000; - union cvmx_usbcx_grstctl c; - - while (1) { - c.u32 = cvmx_usb_read_csr32(usb, address); - if (fflsh_type == 0 && c.s.txfflsh == 0) { - result = 0; - break; - } else if (fflsh_type == 1 && c.s.rxfflsh == 0) { - result = 0; - break; - } else if (cvmx_get_cycle() > done) { - result = -1; - break; - } - - __delay(100); - } - return result; -} - -static void cvmx_fifo_setup(struct octeon_hcd *usb) -{ - union cvmx_usbcx_ghwcfg3 usbcx_ghwcfg3; - union cvmx_usbcx_gnptxfsiz npsiz; - union cvmx_usbcx_hptxfsiz psiz; - - usbcx_ghwcfg3.u32 = cvmx_usb_read_csr32(usb, - CVMX_USBCX_GHWCFG3(usb->index)); - - /* - * Program the USBC_GRXFSIZ register to select the size of the receive - * FIFO (25%). - */ - USB_SET_FIELD32(CVMX_USBCX_GRXFSIZ(usb->index), cvmx_usbcx_grxfsiz, - rxfdep, usbcx_ghwcfg3.s.dfifodepth / 4); - - /* - * Program the USBC_GNPTXFSIZ register to select the size and the start - * address of the non-periodic transmit FIFO for nonperiodic - * transactions (50%). - */ - npsiz.u32 = cvmx_usb_read_csr32(usb, CVMX_USBCX_GNPTXFSIZ(usb->index)); - npsiz.s.nptxfdep = usbcx_ghwcfg3.s.dfifodepth / 2; - npsiz.s.nptxfstaddr = usbcx_ghwcfg3.s.dfifodepth / 4; - cvmx_usb_write_csr32(usb, CVMX_USBCX_GNPTXFSIZ(usb->index), npsiz.u32); - - /* - * Program the USBC_HPTXFSIZ register to select the size and start - * address of the periodic transmit FIFO for periodic transactions - * (25%). - */ - psiz.u32 = cvmx_usb_read_csr32(usb, CVMX_USBCX_HPTXFSIZ(usb->index)); - psiz.s.ptxfsize = usbcx_ghwcfg3.s.dfifodepth / 4; - psiz.s.ptxfstaddr = 3 * usbcx_ghwcfg3.s.dfifodepth / 4; - cvmx_usb_write_csr32(usb, CVMX_USBCX_HPTXFSIZ(usb->index), psiz.u32); - - /* Flush all FIFOs */ - USB_SET_FIELD32(CVMX_USBCX_GRSTCTL(usb->index), - cvmx_usbcx_grstctl, txfnum, 0x10); - USB_SET_FIELD32(CVMX_USBCX_GRSTCTL(usb->index), - cvmx_usbcx_grstctl, txfflsh, 1); - cvmx_wait_tx_rx(usb, 0); - USB_SET_FIELD32(CVMX_USBCX_GRSTCTL(usb->index), - cvmx_usbcx_grstctl, rxfflsh, 1); - cvmx_wait_tx_rx(usb, 1); -} - -/** - * Shutdown a USB port after a call to cvmx_usb_initialize(). - * The port should be disabled with all pipes closed when this - * function is called. - * - * @usb: USB device state populated by cvmx_usb_initialize(). - * - * Returns: 0 or a negative error code. - */ -static int cvmx_usb_shutdown(struct octeon_hcd *usb) -{ - union cvmx_usbnx_clk_ctl usbn_clk_ctl; - - /* Make sure all pipes are closed */ - if (!list_empty(&usb->idle_pipes) || - !list_empty(&usb->active_pipes[CVMX_USB_TRANSFER_ISOCHRONOUS]) || - !list_empty(&usb->active_pipes[CVMX_USB_TRANSFER_INTERRUPT]) || - !list_empty(&usb->active_pipes[CVMX_USB_TRANSFER_CONTROL]) || - !list_empty(&usb->active_pipes[CVMX_USB_TRANSFER_BULK])) - return -EBUSY; - - /* Disable the clocks and put them in power on reset */ - usbn_clk_ctl.u64 = cvmx_read64_uint64(CVMX_USBNX_CLK_CTL(usb->index)); - usbn_clk_ctl.s.enable = 1; - usbn_clk_ctl.s.por = 1; - usbn_clk_ctl.s.hclk_rst = 1; - usbn_clk_ctl.s.prst = 0; - usbn_clk_ctl.s.hrst = 0; - cvmx_write64_uint64(CVMX_USBNX_CLK_CTL(usb->index), usbn_clk_ctl.u64); - return 0; -} - -/** - * Initialize a USB port for use. This must be called before any - * other access to the Octeon USB port is made. The port starts - * off in the disabled state. - * - * @dev: Pointer to struct device for logging purposes. - * @usb: Pointer to struct octeon_hcd. - * - * Returns: 0 or a negative error code. - */ -static int cvmx_usb_initialize(struct device *dev, - struct octeon_hcd *usb) -{ - int channel; - int divisor; - int retries = 0; - union cvmx_usbcx_hcfg usbcx_hcfg; - union cvmx_usbnx_clk_ctl usbn_clk_ctl; - union cvmx_usbcx_gintsts usbc_gintsts; - union cvmx_usbcx_gahbcfg usbcx_gahbcfg; - union cvmx_usbcx_gintmsk usbcx_gintmsk; - union cvmx_usbcx_gusbcfg usbcx_gusbcfg; - union cvmx_usbnx_usbp_ctl_status usbn_usbp_ctl_status; - -retry: - /* - * Power On Reset and PHY Initialization - * - * 1. Wait for DCOK to assert (nothing to do) - * - * 2a. Write USBN0/1_CLK_CTL[POR] = 1 and - * USBN0/1_CLK_CTL[HRST,PRST,HCLK_RST] = 0 - */ - usbn_clk_ctl.u64 = cvmx_read64_uint64(CVMX_USBNX_CLK_CTL(usb->index)); - usbn_clk_ctl.s.por = 1; - usbn_clk_ctl.s.hrst = 0; - usbn_clk_ctl.s.prst = 0; - usbn_clk_ctl.s.hclk_rst = 0; - usbn_clk_ctl.s.enable = 0; - /* - * 2b. Select the USB reference clock/crystal parameters by writing - * appropriate values to USBN0/1_CLK_CTL[P_C_SEL, P_RTYPE, P_COM_ON] - */ - if (usb->init_flags & CVMX_USB_INITIALIZE_FLAGS_CLOCK_XO_GND) { - /* - * The USB port uses 12/24/48MHz 2.5V board clock - * source at USB_XO. USB_XI should be tied to GND. - * Most Octeon evaluation boards require this setting - */ - if (OCTEON_IS_MODEL(OCTEON_CN3XXX) || - OCTEON_IS_MODEL(OCTEON_CN56XX) || - OCTEON_IS_MODEL(OCTEON_CN50XX)) - /* From CN56XX,CN50XX,CN31XX,CN30XX manuals */ - usbn_clk_ctl.s.p_rtype = 2; /* p_rclk=1 & p_xenbn=0 */ - else - /* From CN52XX manual */ - usbn_clk_ctl.s.p_rtype = 1; - - switch (usb->init_flags & - CVMX_USB_INITIALIZE_FLAGS_CLOCK_MHZ_MASK) { - case CVMX_USB_INITIALIZE_FLAGS_CLOCK_12MHZ: - usbn_clk_ctl.s.p_c_sel = 0; - break; - case CVMX_USB_INITIALIZE_FLAGS_CLOCK_24MHZ: - usbn_clk_ctl.s.p_c_sel = 1; - break; - case CVMX_USB_INITIALIZE_FLAGS_CLOCK_48MHZ: - usbn_clk_ctl.s.p_c_sel = 2; - break; - } - } else { - /* - * The USB port uses a 12MHz crystal as clock source - * at USB_XO and USB_XI - */ - if (OCTEON_IS_MODEL(OCTEON_CN3XXX)) - /* From CN31XX,CN30XX manual */ - usbn_clk_ctl.s.p_rtype = 3; /* p_rclk=1 & p_xenbn=1 */ - else - /* From CN56XX,CN52XX,CN50XX manuals. */ - usbn_clk_ctl.s.p_rtype = 0; - - usbn_clk_ctl.s.p_c_sel = 0; - } - /* - * 2c. Select the HCLK via writing USBN0/1_CLK_CTL[DIVIDE, DIVIDE2] and - * setting USBN0/1_CLK_CTL[ENABLE] = 1. Divide the core clock down - * such that USB is as close as possible to 125Mhz - */ - divisor = DIV_ROUND_UP(octeon_get_clock_rate(), 125000000); - /* Lower than 4 doesn't seem to work properly */ - if (divisor < 4) - divisor = 4; - usbn_clk_ctl.s.divide = divisor; - usbn_clk_ctl.s.divide2 = 0; - cvmx_write64_uint64(CVMX_USBNX_CLK_CTL(usb->index), usbn_clk_ctl.u64); - - /* 2d. Write USBN0/1_CLK_CTL[HCLK_RST] = 1 */ - usbn_clk_ctl.s.hclk_rst = 1; - cvmx_write64_uint64(CVMX_USBNX_CLK_CTL(usb->index), usbn_clk_ctl.u64); - /* 2e. Wait 64 core-clock cycles for HCLK to stabilize */ - __delay(64); - /* - * 3. Program the power-on reset field in the USBN clock-control - * register: - * USBN_CLK_CTL[POR] = 0 - */ - usbn_clk_ctl.s.por = 0; - cvmx_write64_uint64(CVMX_USBNX_CLK_CTL(usb->index), usbn_clk_ctl.u64); - /* 4. Wait 1 ms for PHY clock to start */ - mdelay(1); - /* - * 5. Program the Reset input from automatic test equipment field in the - * USBP control and status register: - * USBN_USBP_CTL_STATUS[ATE_RESET] = 1 - */ - usbn_usbp_ctl_status.u64 = - cvmx_read64_uint64(CVMX_USBNX_USBP_CTL_STATUS(usb->index)); - usbn_usbp_ctl_status.s.ate_reset = 1; - cvmx_write64_uint64(CVMX_USBNX_USBP_CTL_STATUS(usb->index), - usbn_usbp_ctl_status.u64); - /* 6. Wait 10 cycles */ - __delay(10); - /* - * 7. Clear ATE_RESET field in the USBN clock-control register: - * USBN_USBP_CTL_STATUS[ATE_RESET] = 0 - */ - usbn_usbp_ctl_status.s.ate_reset = 0; - cvmx_write64_uint64(CVMX_USBNX_USBP_CTL_STATUS(usb->index), - usbn_usbp_ctl_status.u64); - /* - * 8. Program the PHY reset field in the USBN clock-control register: - * USBN_CLK_CTL[PRST] = 1 - */ - usbn_clk_ctl.s.prst = 1; - cvmx_write64_uint64(CVMX_USBNX_CLK_CTL(usb->index), usbn_clk_ctl.u64); - /* - * 9. Program the USBP control and status register to select host or - * device mode. USBN_USBP_CTL_STATUS[HST_MODE] = 0 for host, = 1 for - * device - */ - usbn_usbp_ctl_status.s.hst_mode = 0; - cvmx_write64_uint64(CVMX_USBNX_USBP_CTL_STATUS(usb->index), - usbn_usbp_ctl_status.u64); - /* 10. Wait 1 us */ - udelay(1); - /* - * 11. Program the hreset_n field in the USBN clock-control register: - * USBN_CLK_CTL[HRST] = 1 - */ - usbn_clk_ctl.s.hrst = 1; - cvmx_write64_uint64(CVMX_USBNX_CLK_CTL(usb->index), usbn_clk_ctl.u64); - /* 12. Proceed to USB core initialization */ - usbn_clk_ctl.s.enable = 1; - cvmx_write64_uint64(CVMX_USBNX_CLK_CTL(usb->index), usbn_clk_ctl.u64); - udelay(1); - - /* - * USB Core Initialization - * - * 1. Read USBC_GHWCFG1, USBC_GHWCFG2, USBC_GHWCFG3, USBC_GHWCFG4 to - * determine USB core configuration parameters. - * - * Nothing needed - * - * 2. Program the following fields in the global AHB configuration - * register (USBC_GAHBCFG) - * DMA mode, USBC_GAHBCFG[DMAEn]: 1 = DMA mode, 0 = slave mode - * Burst length, USBC_GAHBCFG[HBSTLEN] = 0 - * Nonperiodic TxFIFO empty level (slave mode only), - * USBC_GAHBCFG[NPTXFEMPLVL] - * Periodic TxFIFO empty level (slave mode only), - * USBC_GAHBCFG[PTXFEMPLVL] - * Global interrupt mask, USBC_GAHBCFG[GLBLINTRMSK] = 1 - */ - usbcx_gahbcfg.u32 = 0; - usbcx_gahbcfg.s.dmaen = !(usb->init_flags & - CVMX_USB_INITIALIZE_FLAGS_NO_DMA); - usbcx_gahbcfg.s.hbstlen = 0; - usbcx_gahbcfg.s.nptxfemplvl = 1; - usbcx_gahbcfg.s.ptxfemplvl = 1; - usbcx_gahbcfg.s.glblintrmsk = 1; - cvmx_usb_write_csr32(usb, CVMX_USBCX_GAHBCFG(usb->index), - usbcx_gahbcfg.u32); - - /* - * 3. Program the following fields in USBC_GUSBCFG register. - * HS/FS timeout calibration, USBC_GUSBCFG[TOUTCAL] = 0 - * ULPI DDR select, USBC_GUSBCFG[DDRSEL] = 0 - * USB turnaround time, USBC_GUSBCFG[USBTRDTIM] = 0x5 - * PHY low-power clock select, USBC_GUSBCFG[PHYLPWRCLKSEL] = 0 - */ - usbcx_gusbcfg.u32 = cvmx_usb_read_csr32(usb, - CVMX_USBCX_GUSBCFG(usb->index)); - usbcx_gusbcfg.s.toutcal = 0; - usbcx_gusbcfg.s.ddrsel = 0; - usbcx_gusbcfg.s.usbtrdtim = 0x5; - usbcx_gusbcfg.s.phylpwrclksel = 0; - cvmx_usb_write_csr32(usb, CVMX_USBCX_GUSBCFG(usb->index), - usbcx_gusbcfg.u32); - - /* - * 4. The software must unmask the following bits in the USBC_GINTMSK - * register. - * OTG interrupt mask, USBC_GINTMSK[OTGINTMSK] = 1 - * Mode mismatch interrupt mask, USBC_GINTMSK[MODEMISMSK] = 1 - */ - usbcx_gintmsk.u32 = cvmx_usb_read_csr32(usb, - CVMX_USBCX_GINTMSK(usb->index)); - usbcx_gintmsk.s.otgintmsk = 1; - usbcx_gintmsk.s.modemismsk = 1; - usbcx_gintmsk.s.hchintmsk = 1; - usbcx_gintmsk.s.sofmsk = 0; - /* We need RX FIFO interrupts if we don't have DMA */ - if (usb->init_flags & CVMX_USB_INITIALIZE_FLAGS_NO_DMA) - usbcx_gintmsk.s.rxflvlmsk = 1; - cvmx_usb_write_csr32(usb, CVMX_USBCX_GINTMSK(usb->index), - usbcx_gintmsk.u32); - - /* - * Disable all channel interrupts. We'll enable them per channel later. - */ - for (channel = 0; channel < 8; channel++) - cvmx_usb_write_csr32(usb, - CVMX_USBCX_HCINTMSKX(channel, usb->index), - 0); - - /* - * Host Port Initialization - * - * 1. Program the host-port interrupt-mask field to unmask, - * USBC_GINTMSK[PRTINT] = 1 - */ - USB_SET_FIELD32(CVMX_USBCX_GINTMSK(usb->index), - cvmx_usbcx_gintmsk, prtintmsk, 1); - USB_SET_FIELD32(CVMX_USBCX_GINTMSK(usb->index), - cvmx_usbcx_gintmsk, disconnintmsk, 1); - - /* - * 2. Program the USBC_HCFG register to select full-speed host - * or high-speed host. - */ - usbcx_hcfg.u32 = cvmx_usb_read_csr32(usb, CVMX_USBCX_HCFG(usb->index)); - usbcx_hcfg.s.fslssupp = 0; - usbcx_hcfg.s.fslspclksel = 0; - cvmx_usb_write_csr32(usb, CVMX_USBCX_HCFG(usb->index), usbcx_hcfg.u32); - - cvmx_fifo_setup(usb); - - /* - * If the controller is getting port events right after the reset, it - * means the initialization failed. Try resetting the controller again - * in such case. This is seen to happen after cold boot on DSR-1000N. - */ - usbc_gintsts.u32 = cvmx_usb_read_csr32(usb, - CVMX_USBCX_GINTSTS(usb->index)); - cvmx_usb_write_csr32(usb, CVMX_USBCX_GINTSTS(usb->index), - usbc_gintsts.u32); - dev_dbg(dev, "gintsts after reset: 0x%x\n", (int)usbc_gintsts.u32); - if (!usbc_gintsts.s.disconnint && !usbc_gintsts.s.prtint) - return 0; - if (retries++ >= 5) - return -EAGAIN; - dev_info(dev, "controller reset failed (gintsts=0x%x) - retrying\n", - (int)usbc_gintsts.u32); - msleep(50); - cvmx_usb_shutdown(usb); - msleep(50); - goto retry; -} - -/** - * Reset a USB port. After this call succeeds, the USB port is - * online and servicing requests. - * - * @usb: USB device state populated by cvmx_usb_initialize(). - */ -static void cvmx_usb_reset_port(struct octeon_hcd *usb) -{ - usb->usbcx_hprt.u32 = cvmx_usb_read_csr32(usb, - CVMX_USBCX_HPRT(usb->index)); - - /* Program the port reset bit to start the reset process */ - USB_SET_FIELD32(CVMX_USBCX_HPRT(usb->index), cvmx_usbcx_hprt, - prtrst, 1); - - /* - * Wait at least 50ms (high speed), or 10ms (full speed) for the reset - * process to complete. - */ - mdelay(50); - - /* Program the port reset bit to 0, USBC_HPRT[PRTRST] = 0 */ - USB_SET_FIELD32(CVMX_USBCX_HPRT(usb->index), cvmx_usbcx_hprt, - prtrst, 0); - - /* - * Read the port speed field to get the enumerated speed, - * USBC_HPRT[PRTSPD]. - */ - usb->usbcx_hprt.u32 = cvmx_usb_read_csr32(usb, - CVMX_USBCX_HPRT(usb->index)); -} - -/** - * Disable a USB port. After this call the USB port will not - * generate data transfers and will not generate events. - * Transactions in process will fail and call their - * associated callbacks. - * - * @usb: USB device state populated by cvmx_usb_initialize(). - * - * Returns: 0 or a negative error code. - */ -static int cvmx_usb_disable(struct octeon_hcd *usb) -{ - /* Disable the port */ - USB_SET_FIELD32(CVMX_USBCX_HPRT(usb->index), cvmx_usbcx_hprt, - prtena, 1); - return 0; -} - -/** - * Get the current state of the USB port. Use this call to - * determine if the usb port has anything connected, is enabled, - * or has some sort of error condition. The return value of this - * call has "changed" bits to signal of the value of some fields - * have changed between calls. - * - * @usb: USB device state populated by cvmx_usb_initialize(). - * - * Returns: Port status information - */ -static struct cvmx_usb_port_status cvmx_usb_get_status(struct octeon_hcd *usb) -{ - union cvmx_usbcx_hprt usbc_hprt; - struct cvmx_usb_port_status result; - - memset(&result, 0, sizeof(result)); - - usbc_hprt.u32 = cvmx_usb_read_csr32(usb, CVMX_USBCX_HPRT(usb->index)); - result.port_enabled = usbc_hprt.s.prtena; - result.port_over_current = usbc_hprt.s.prtovrcurract; - result.port_powered = usbc_hprt.s.prtpwr; - result.port_speed = usbc_hprt.s.prtspd; - result.connected = usbc_hprt.s.prtconnsts; - result.connect_change = - result.connected != usb->port_status.connected; - - return result; -} - -/** - * Open a virtual pipe between the host and a USB device. A pipe - * must be opened before data can be transferred between a device - * and Octeon. - * - * @usb: USB device state populated by cvmx_usb_initialize(). - * @device_addr: - * USB device address to open the pipe to - * (0-127). - * @endpoint_num: - * USB endpoint number to open the pipe to - * (0-15). - * @device_speed: - * The speed of the device the pipe is going - * to. This must match the device's speed, - * which may be different than the port speed. - * @max_packet: The maximum packet length the device can - * transmit/receive (low speed=0-8, full - * speed=0-1023, high speed=0-1024). This value - * comes from the standard endpoint descriptor - * field wMaxPacketSize bits <10:0>. - * @transfer_type: - * The type of transfer this pipe is for. - * @transfer_dir: - * The direction the pipe is in. This is not - * used for control pipes. - * @interval: For ISOCHRONOUS and INTERRUPT transfers, - * this is how often the transfer is scheduled - * for. All other transfers should specify - * zero. The units are in frames (8000/sec at - * high speed, 1000/sec for full speed). - * @multi_count: - * For high speed devices, this is the maximum - * allowed number of packet per microframe. - * Specify zero for non high speed devices. This - * value comes from the standard endpoint descriptor - * field wMaxPacketSize bits <12:11>. - * @hub_device_addr: - * Hub device address this device is connected - * to. Devices connected directly to Octeon - * use zero. This is only used when the device - * is full/low speed behind a high speed hub. - * The address will be of the high speed hub, - * not and full speed hubs after it. - * @hub_port: Which port on the hub the device is - * connected. Use zero for devices connected - * directly to Octeon. Like hub_device_addr, - * this is only used for full/low speed - * devices behind a high speed hub. - * - * Returns: A non-NULL value is a pipe. NULL means an error. - */ -static struct cvmx_usb_pipe *cvmx_usb_open_pipe(struct octeon_hcd *usb, - int device_addr, - int endpoint_num, - enum cvmx_usb_speed - device_speed, - int max_packet, - enum cvmx_usb_transfer - transfer_type, - enum cvmx_usb_direction - transfer_dir, - int interval, int multi_count, - int hub_device_addr, - int hub_port) -{ - struct cvmx_usb_pipe *pipe; - - pipe = kzalloc(sizeof(*pipe), GFP_ATOMIC); - if (!pipe) - return NULL; - if ((device_speed == CVMX_USB_SPEED_HIGH) && - (transfer_dir == CVMX_USB_DIRECTION_OUT) && - (transfer_type == CVMX_USB_TRANSFER_BULK)) - pipe->flags |= CVMX_USB_PIPE_FLAGS_NEED_PING; - pipe->device_addr = device_addr; - pipe->endpoint_num = endpoint_num; - pipe->device_speed = device_speed; - pipe->max_packet = max_packet; - pipe->transfer_type = transfer_type; - pipe->transfer_dir = transfer_dir; - INIT_LIST_HEAD(&pipe->transactions); - - /* - * All pipes use interval to rate limit NAK processing. Force an - * interval if one wasn't supplied - */ - if (!interval) - interval = 1; - if (cvmx_usb_pipe_needs_split(usb, pipe)) { - pipe->interval = interval * 8; - /* Force start splits to be schedule on uFrame 0 */ - pipe->next_tx_frame = ((usb->frame_number + 7) & ~7) + - pipe->interval; - } else { - pipe->interval = interval; - pipe->next_tx_frame = usb->frame_number + pipe->interval; - } - pipe->multi_count = multi_count; - pipe->hub_device_addr = hub_device_addr; - pipe->hub_port = hub_port; - pipe->pid_toggle = 0; - pipe->split_sc_frame = -1; - list_add_tail(&pipe->node, &usb->idle_pipes); - - /* - * We don't need to tell the hardware about this pipe yet since - * it doesn't have any submitted requests - */ - - return pipe; -} - -/** - * Poll the RX FIFOs and remove data as needed. This function is only used - * in non DMA mode. It is very important that this function be called quickly - * enough to prevent FIFO overflow. - * - * @usb: USB device state populated by cvmx_usb_initialize(). - */ -static void cvmx_usb_poll_rx_fifo(struct octeon_hcd *usb) -{ - union cvmx_usbcx_grxstsph rx_status; - int channel; - int bytes; - u64 address; - u32 *ptr; - - rx_status.u32 = cvmx_usb_read_csr32(usb, - CVMX_USBCX_GRXSTSPH(usb->index)); - /* Only read data if IN data is there */ - if (rx_status.s.pktsts != 2) - return; - /* Check if no data is available */ - if (!rx_status.s.bcnt) - return; - - channel = rx_status.s.chnum; - bytes = rx_status.s.bcnt; - if (!bytes) - return; - - /* Get where the DMA engine would have written this data */ - address = cvmx_read64_uint64(CVMX_USBNX_DMA0_INB_CHN0(usb->index) + - channel * 8); - - ptr = cvmx_phys_to_ptr(address); - cvmx_write64_uint64(CVMX_USBNX_DMA0_INB_CHN0(usb->index) + channel * 8, - address + bytes); - - /* Loop writing the FIFO data for this packet into memory */ - while (bytes > 0) { - *ptr++ = cvmx_usb_read_csr32(usb, - USB_FIFO_ADDRESS(channel, usb->index)); - bytes -= 4; - } - CVMX_SYNCW; -} - -/** - * Fill the TX hardware fifo with data out of the software - * fifos - * - * @usb: USB device state populated by cvmx_usb_initialize(). - * @fifo: Software fifo to use - * @available: Amount of space in the hardware fifo - * - * Returns: Non zero if the hardware fifo was too small and needs - * to be serviced again. - */ -static int cvmx_usb_fill_tx_hw(struct octeon_hcd *usb, - struct cvmx_usb_tx_fifo *fifo, int available) -{ - /* - * We're done either when there isn't anymore space or the software FIFO - * is empty - */ - while (available && (fifo->head != fifo->tail)) { - int i = fifo->tail; - const u32 *ptr = cvmx_phys_to_ptr(fifo->entry[i].address); - u64 csr_address = USB_FIFO_ADDRESS(fifo->entry[i].channel, - usb->index) ^ 4; - int words = available; - - /* Limit the amount of data to what the SW fifo has */ - if (fifo->entry[i].size <= available) { - words = fifo->entry[i].size; - fifo->tail++; - if (fifo->tail > MAX_CHANNELS) - fifo->tail = 0; - } - - /* Update the next locations and counts */ - available -= words; - fifo->entry[i].address += words * 4; - fifo->entry[i].size -= words; - - /* - * Write the HW fifo data. The read every three writes is due - * to an errata on CN3XXX chips - */ - while (words > 3) { - cvmx_write64_uint32(csr_address, *ptr++); - cvmx_write64_uint32(csr_address, *ptr++); - cvmx_write64_uint32(csr_address, *ptr++); - cvmx_read64_uint64( - CVMX_USBNX_DMA0_INB_CHN0(usb->index)); - words -= 3; - } - cvmx_write64_uint32(csr_address, *ptr++); - if (--words) { - cvmx_write64_uint32(csr_address, *ptr++); - if (--words) - cvmx_write64_uint32(csr_address, *ptr++); - } - cvmx_read64_uint64(CVMX_USBNX_DMA0_INB_CHN0(usb->index)); - } - return fifo->head != fifo->tail; -} - -/** - * Check the hardware FIFOs and fill them as needed - * - * @usb: USB device state populated by cvmx_usb_initialize(). - */ -static void cvmx_usb_poll_tx_fifo(struct octeon_hcd *usb) -{ - if (usb->periodic.head != usb->periodic.tail) { - union cvmx_usbcx_hptxsts tx_status; - - tx_status.u32 = cvmx_usb_read_csr32(usb, - CVMX_USBCX_HPTXSTS(usb->index)); - if (cvmx_usb_fill_tx_hw(usb, &usb->periodic, - tx_status.s.ptxfspcavail)) - USB_SET_FIELD32(CVMX_USBCX_GINTMSK(usb->index), - cvmx_usbcx_gintmsk, ptxfempmsk, 1); - else - USB_SET_FIELD32(CVMX_USBCX_GINTMSK(usb->index), - cvmx_usbcx_gintmsk, ptxfempmsk, 0); - } - - if (usb->nonperiodic.head != usb->nonperiodic.tail) { - union cvmx_usbcx_gnptxsts tx_status; - - tx_status.u32 = cvmx_usb_read_csr32(usb, - CVMX_USBCX_GNPTXSTS(usb->index)); - if (cvmx_usb_fill_tx_hw(usb, &usb->nonperiodic, - tx_status.s.nptxfspcavail)) - USB_SET_FIELD32(CVMX_USBCX_GINTMSK(usb->index), - cvmx_usbcx_gintmsk, nptxfempmsk, 1); - else - USB_SET_FIELD32(CVMX_USBCX_GINTMSK(usb->index), - cvmx_usbcx_gintmsk, nptxfempmsk, 0); - } -} - -/** - * Fill the TX FIFO with an outgoing packet - * - * @usb: USB device state populated by cvmx_usb_initialize(). - * @channel: Channel number to get packet from - */ -static void cvmx_usb_fill_tx_fifo(struct octeon_hcd *usb, int channel) -{ - union cvmx_usbcx_hccharx hcchar; - union cvmx_usbcx_hcspltx usbc_hcsplt; - union cvmx_usbcx_hctsizx usbc_hctsiz; - struct cvmx_usb_tx_fifo *fifo; - - /* We only need to fill data on outbound channels */ - hcchar.u32 = cvmx_usb_read_csr32(usb, - CVMX_USBCX_HCCHARX(channel, usb->index)); - if (hcchar.s.epdir != CVMX_USB_DIRECTION_OUT) - return; - - /* OUT Splits only have data on the start and not the complete */ - usbc_hcsplt.u32 = cvmx_usb_read_csr32(usb, - CVMX_USBCX_HCSPLTX(channel, usb->index)); - if (usbc_hcsplt.s.spltena && usbc_hcsplt.s.compsplt) - return; - - /* - * Find out how many bytes we need to fill and convert it into 32bit - * words. - */ - usbc_hctsiz.u32 = cvmx_usb_read_csr32(usb, - CVMX_USBCX_HCTSIZX(channel, usb->index)); - if (!usbc_hctsiz.s.xfersize) - return; - - if ((hcchar.s.eptype == CVMX_USB_TRANSFER_INTERRUPT) || - (hcchar.s.eptype == CVMX_USB_TRANSFER_ISOCHRONOUS)) - fifo = &usb->periodic; - else - fifo = &usb->nonperiodic; - - fifo->entry[fifo->head].channel = channel; - fifo->entry[fifo->head].address = - cvmx_read64_uint64(CVMX_USBNX_DMA0_OUTB_CHN0(usb->index) + - channel * 8); - fifo->entry[fifo->head].size = (usbc_hctsiz.s.xfersize + 3) >> 2; - fifo->head++; - if (fifo->head > MAX_CHANNELS) - fifo->head = 0; - - cvmx_usb_poll_tx_fifo(usb); -} - -/** - * Perform channel specific setup for Control transactions. All - * the generic stuff will already have been done in cvmx_usb_start_channel(). - * - * @usb: USB device state populated by cvmx_usb_initialize(). - * @channel: Channel to setup - * @pipe: Pipe for control transaction - */ -static void cvmx_usb_start_channel_control(struct octeon_hcd *usb, - int channel, - struct cvmx_usb_pipe *pipe) -{ - struct usb_hcd *hcd = octeon_to_hcd(usb); - struct device *dev = hcd->self.controller; - struct cvmx_usb_transaction *transaction = - list_first_entry(&pipe->transactions, typeof(*transaction), - node); - struct usb_ctrlrequest *header = - cvmx_phys_to_ptr(transaction->control_header); - int bytes_to_transfer = transaction->buffer_length - - transaction->actual_bytes; - int packets_to_transfer; - union cvmx_usbcx_hctsizx usbc_hctsiz; - - usbc_hctsiz.u32 = cvmx_usb_read_csr32(usb, - CVMX_USBCX_HCTSIZX(channel, usb->index)); - - switch (transaction->stage) { - case CVMX_USB_STAGE_NON_CONTROL: - case CVMX_USB_STAGE_NON_CONTROL_SPLIT_COMPLETE: - dev_err(dev, "%s: ERROR - Non control stage\n", __func__); - break; - case CVMX_USB_STAGE_SETUP: - usbc_hctsiz.s.pid = 3; /* Setup */ - bytes_to_transfer = sizeof(*header); - /* All Control operations start with a setup going OUT */ - USB_SET_FIELD32(CVMX_USBCX_HCCHARX(channel, usb->index), - cvmx_usbcx_hccharx, epdir, - CVMX_USB_DIRECTION_OUT); - /* - * Setup send the control header instead of the buffer data. The - * buffer data will be used in the next stage - */ - cvmx_write64_uint64(CVMX_USBNX_DMA0_OUTB_CHN0(usb->index) + - channel * 8, - transaction->control_header); - break; - case CVMX_USB_STAGE_SETUP_SPLIT_COMPLETE: - usbc_hctsiz.s.pid = 3; /* Setup */ - bytes_to_transfer = 0; - /* All Control operations start with a setup going OUT */ - USB_SET_FIELD32(CVMX_USBCX_HCCHARX(channel, usb->index), - cvmx_usbcx_hccharx, epdir, - CVMX_USB_DIRECTION_OUT); - - USB_SET_FIELD32(CVMX_USBCX_HCSPLTX(channel, usb->index), - cvmx_usbcx_hcspltx, compsplt, 1); - break; - case CVMX_USB_STAGE_DATA: - usbc_hctsiz.s.pid = cvmx_usb_get_data_pid(pipe); - if (cvmx_usb_pipe_needs_split(usb, pipe)) { - if (header->bRequestType & USB_DIR_IN) - bytes_to_transfer = 0; - else if (bytes_to_transfer > pipe->max_packet) - bytes_to_transfer = pipe->max_packet; - } - USB_SET_FIELD32(CVMX_USBCX_HCCHARX(channel, usb->index), - cvmx_usbcx_hccharx, epdir, - ((header->bRequestType & USB_DIR_IN) ? - CVMX_USB_DIRECTION_IN : - CVMX_USB_DIRECTION_OUT)); - break; - case CVMX_USB_STAGE_DATA_SPLIT_COMPLETE: - usbc_hctsiz.s.pid = cvmx_usb_get_data_pid(pipe); - if (!(header->bRequestType & USB_DIR_IN)) - bytes_to_transfer = 0; - USB_SET_FIELD32(CVMX_USBCX_HCCHARX(channel, usb->index), - cvmx_usbcx_hccharx, epdir, - ((header->bRequestType & USB_DIR_IN) ? - CVMX_USB_DIRECTION_IN : - CVMX_USB_DIRECTION_OUT)); - USB_SET_FIELD32(CVMX_USBCX_HCSPLTX(channel, usb->index), - cvmx_usbcx_hcspltx, compsplt, 1); - break; - case CVMX_USB_STAGE_STATUS: - usbc_hctsiz.s.pid = cvmx_usb_get_data_pid(pipe); - bytes_to_transfer = 0; - USB_SET_FIELD32(CVMX_USBCX_HCCHARX(channel, usb->index), - cvmx_usbcx_hccharx, epdir, - ((header->bRequestType & USB_DIR_IN) ? - CVMX_USB_DIRECTION_OUT : - CVMX_USB_DIRECTION_IN)); - break; - case CVMX_USB_STAGE_STATUS_SPLIT_COMPLETE: - usbc_hctsiz.s.pid = cvmx_usb_get_data_pid(pipe); - bytes_to_transfer = 0; - USB_SET_FIELD32(CVMX_USBCX_HCCHARX(channel, usb->index), - cvmx_usbcx_hccharx, epdir, - ((header->bRequestType & USB_DIR_IN) ? - CVMX_USB_DIRECTION_OUT : - CVMX_USB_DIRECTION_IN)); - USB_SET_FIELD32(CVMX_USBCX_HCSPLTX(channel, usb->index), - cvmx_usbcx_hcspltx, compsplt, 1); - break; - } - - /* - * Make sure the transfer never exceeds the byte limit of the hardware. - * Further bytes will be sent as continued transactions - */ - if (bytes_to_transfer > MAX_TRANSFER_BYTES) { - /* Round MAX_TRANSFER_BYTES to a multiple of out packet size */ - bytes_to_transfer = MAX_TRANSFER_BYTES / pipe->max_packet; - bytes_to_transfer *= pipe->max_packet; - } - - /* - * Calculate the number of packets to transfer. If the length is zero - * we still need to transfer one packet - */ - packets_to_transfer = DIV_ROUND_UP(bytes_to_transfer, - pipe->max_packet); - if (packets_to_transfer == 0) { - packets_to_transfer = 1; - } else if ((packets_to_transfer > 1) && - (usb->init_flags & CVMX_USB_INITIALIZE_FLAGS_NO_DMA)) { - /* - * Limit to one packet when not using DMA. Channels must be - * restarted between every packet for IN transactions, so there - * is no reason to do multiple packets in a row - */ - packets_to_transfer = 1; - bytes_to_transfer = packets_to_transfer * pipe->max_packet; - } else if (packets_to_transfer > MAX_TRANSFER_PACKETS) { - /* - * Limit the number of packet and data transferred to what the - * hardware can handle - */ - packets_to_transfer = MAX_TRANSFER_PACKETS; - bytes_to_transfer = packets_to_transfer * pipe->max_packet; - } - - usbc_hctsiz.s.xfersize = bytes_to_transfer; - usbc_hctsiz.s.pktcnt = packets_to_transfer; - - cvmx_usb_write_csr32(usb, CVMX_USBCX_HCTSIZX(channel, usb->index), - usbc_hctsiz.u32); -} - -/** - * Start a channel to perform the pipe's head transaction - * - * @usb: USB device state populated by cvmx_usb_initialize(). - * @channel: Channel to setup - * @pipe: Pipe to start - */ -static void cvmx_usb_start_channel(struct octeon_hcd *usb, int channel, - struct cvmx_usb_pipe *pipe) -{ - struct cvmx_usb_transaction *transaction = - list_first_entry(&pipe->transactions, typeof(*transaction), - node); - - /* Make sure all writes to the DMA region get flushed */ - CVMX_SYNCW; - - /* Attach the channel to the pipe */ - usb->pipe_for_channel[channel] = pipe; - pipe->channel = channel; - pipe->flags |= CVMX_USB_PIPE_FLAGS_SCHEDULED; - - /* Mark this channel as in use */ - usb->idle_hardware_channels &= ~(1 << channel); - - /* Enable the channel interrupt bits */ - { - union cvmx_usbcx_hcintx usbc_hcint; - union cvmx_usbcx_hcintmskx usbc_hcintmsk; - union cvmx_usbcx_haintmsk usbc_haintmsk; - - /* Clear all channel status bits */ - usbc_hcint.u32 = cvmx_usb_read_csr32(usb, - CVMX_USBCX_HCINTX(channel, usb->index)); - - cvmx_usb_write_csr32(usb, - CVMX_USBCX_HCINTX(channel, usb->index), - usbc_hcint.u32); - - usbc_hcintmsk.u32 = 0; - usbc_hcintmsk.s.chhltdmsk = 1; - if (usb->init_flags & CVMX_USB_INITIALIZE_FLAGS_NO_DMA) { - /* - * Channels need these extra interrupts when we aren't - * in DMA mode. - */ - usbc_hcintmsk.s.datatglerrmsk = 1; - usbc_hcintmsk.s.frmovrunmsk = 1; - usbc_hcintmsk.s.bblerrmsk = 1; - usbc_hcintmsk.s.xacterrmsk = 1; - if (cvmx_usb_pipe_needs_split(usb, pipe)) { - /* - * Splits don't generate xfercompl, so we need - * ACK and NYET. - */ - usbc_hcintmsk.s.nyetmsk = 1; - usbc_hcintmsk.s.ackmsk = 1; - } - usbc_hcintmsk.s.nakmsk = 1; - usbc_hcintmsk.s.stallmsk = 1; - usbc_hcintmsk.s.xfercomplmsk = 1; - } - cvmx_usb_write_csr32(usb, - CVMX_USBCX_HCINTMSKX(channel, usb->index), - usbc_hcintmsk.u32); - - /* Enable the channel interrupt to propagate */ - usbc_haintmsk.u32 = cvmx_usb_read_csr32(usb, - CVMX_USBCX_HAINTMSK(usb->index)); - usbc_haintmsk.s.haintmsk |= 1 << channel; - cvmx_usb_write_csr32(usb, CVMX_USBCX_HAINTMSK(usb->index), - usbc_haintmsk.u32); - } - - /* Setup the location the DMA engine uses. */ - { - u64 reg; - u64 dma_address = transaction->buffer + - transaction->actual_bytes; - - if (transaction->type == CVMX_USB_TRANSFER_ISOCHRONOUS) - dma_address = transaction->buffer + - transaction->iso_packets[0].offset + - transaction->actual_bytes; - - if (pipe->transfer_dir == CVMX_USB_DIRECTION_OUT) - reg = CVMX_USBNX_DMA0_OUTB_CHN0(usb->index); - else - reg = CVMX_USBNX_DMA0_INB_CHN0(usb->index); - cvmx_write64_uint64(reg + channel * 8, dma_address); - } - - /* Setup both the size of the transfer and the SPLIT characteristics */ - { - union cvmx_usbcx_hcspltx usbc_hcsplt = {.u32 = 0}; - union cvmx_usbcx_hctsizx usbc_hctsiz = {.u32 = 0}; - int packets_to_transfer; - int bytes_to_transfer = transaction->buffer_length - - transaction->actual_bytes; - - /* - * ISOCHRONOUS transactions store each individual transfer size - * in the packet structure, not the global buffer_length - */ - if (transaction->type == CVMX_USB_TRANSFER_ISOCHRONOUS) - bytes_to_transfer = - transaction->iso_packets[0].length - - transaction->actual_bytes; - - /* - * We need to do split transactions when we are talking to non - * high speed devices that are behind a high speed hub - */ - if (cvmx_usb_pipe_needs_split(usb, pipe)) { - /* - * On the start split phase (stage is even) record the - * frame number we will need to send the split complete. - * We only store the lower two bits since the time ahead - * can only be two frames - */ - if ((transaction->stage & 1) == 0) { - if (transaction->type == CVMX_USB_TRANSFER_BULK) - pipe->split_sc_frame = - (usb->frame_number + 1) & 0x7f; - else - pipe->split_sc_frame = - (usb->frame_number + 2) & 0x7f; - } else { - pipe->split_sc_frame = -1; - } - - usbc_hcsplt.s.spltena = 1; - usbc_hcsplt.s.hubaddr = pipe->hub_device_addr; - usbc_hcsplt.s.prtaddr = pipe->hub_port; - usbc_hcsplt.s.compsplt = (transaction->stage == - CVMX_USB_STAGE_NON_CONTROL_SPLIT_COMPLETE); - - /* - * SPLIT transactions can only ever transmit one data - * packet so limit the transfer size to the max packet - * size - */ - if (bytes_to_transfer > pipe->max_packet) - bytes_to_transfer = pipe->max_packet; - - /* - * ISOCHRONOUS OUT splits are unique in that they limit - * data transfers to 188 byte chunks representing the - * begin/middle/end of the data or all - */ - if (!usbc_hcsplt.s.compsplt && - (pipe->transfer_dir == CVMX_USB_DIRECTION_OUT) && - (pipe->transfer_type == - CVMX_USB_TRANSFER_ISOCHRONOUS)) { - /* - * Clear the split complete frame number as - * there isn't going to be a split complete - */ - pipe->split_sc_frame = -1; - /* - * See if we've started this transfer and sent - * data - */ - if (transaction->actual_bytes == 0) { - /* - * Nothing sent yet, this is either a - * begin or the entire payload - */ - if (bytes_to_transfer <= 188) - /* Entire payload in one go */ - usbc_hcsplt.s.xactpos = 3; - else - /* First part of payload */ - usbc_hcsplt.s.xactpos = 2; - } else { - /* - * Continuing the previous data, we must - * either be in the middle or at the end - */ - if (bytes_to_transfer <= 188) - /* End of payload */ - usbc_hcsplt.s.xactpos = 1; - else - /* Middle of payload */ - usbc_hcsplt.s.xactpos = 0; - } - /* - * Again, the transfer size is limited to 188 - * bytes - */ - if (bytes_to_transfer > 188) - bytes_to_transfer = 188; - } - } - - /* - * Make sure the transfer never exceeds the byte limit of the - * hardware. Further bytes will be sent as continued - * transactions - */ - if (bytes_to_transfer > MAX_TRANSFER_BYTES) { - /* - * Round MAX_TRANSFER_BYTES to a multiple of out packet - * size - */ - bytes_to_transfer = MAX_TRANSFER_BYTES / - pipe->max_packet; - bytes_to_transfer *= pipe->max_packet; - } - - /* - * Calculate the number of packets to transfer. If the length is - * zero we still need to transfer one packet - */ - packets_to_transfer = - DIV_ROUND_UP(bytes_to_transfer, pipe->max_packet); - if (packets_to_transfer == 0) { - packets_to_transfer = 1; - } else if ((packets_to_transfer > 1) && - (usb->init_flags & - CVMX_USB_INITIALIZE_FLAGS_NO_DMA)) { - /* - * Limit to one packet when not using DMA. Channels must - * be restarted between every packet for IN - * transactions, so there is no reason to do multiple - * packets in a row - */ - packets_to_transfer = 1; - bytes_to_transfer = packets_to_transfer * - pipe->max_packet; - } else if (packets_to_transfer > MAX_TRANSFER_PACKETS) { - /* - * Limit the number of packet and data transferred to - * what the hardware can handle - */ - packets_to_transfer = MAX_TRANSFER_PACKETS; - bytes_to_transfer = packets_to_transfer * - pipe->max_packet; - } - - usbc_hctsiz.s.xfersize = bytes_to_transfer; - usbc_hctsiz.s.pktcnt = packets_to_transfer; - - /* Update the DATA0/DATA1 toggle */ - usbc_hctsiz.s.pid = cvmx_usb_get_data_pid(pipe); - /* - * High speed pipes may need a hardware ping before they start - */ - if (pipe->flags & CVMX_USB_PIPE_FLAGS_NEED_PING) - usbc_hctsiz.s.dopng = 1; - - cvmx_usb_write_csr32(usb, - CVMX_USBCX_HCSPLTX(channel, usb->index), - usbc_hcsplt.u32); - cvmx_usb_write_csr32(usb, - CVMX_USBCX_HCTSIZX(channel, usb->index), - usbc_hctsiz.u32); - } - - /* Setup the Host Channel Characteristics Register */ - { - union cvmx_usbcx_hccharx usbc_hcchar = {.u32 = 0}; - - /* - * Set the startframe odd/even properly. This is only used for - * periodic - */ - usbc_hcchar.s.oddfrm = usb->frame_number & 1; - - /* - * Set the number of back to back packets allowed by this - * endpoint. Split transactions interpret "ec" as the number of - * immediate retries of failure. These retries happen too - * quickly, so we disable these entirely for splits - */ - if (cvmx_usb_pipe_needs_split(usb, pipe)) - usbc_hcchar.s.ec = 1; - else if (pipe->multi_count < 1) - usbc_hcchar.s.ec = 1; - else if (pipe->multi_count > 3) - usbc_hcchar.s.ec = 3; - else - usbc_hcchar.s.ec = pipe->multi_count; - - /* Set the rest of the endpoint specific settings */ - usbc_hcchar.s.devaddr = pipe->device_addr; - usbc_hcchar.s.eptype = transaction->type; - usbc_hcchar.s.lspddev = - (pipe->device_speed == CVMX_USB_SPEED_LOW); - usbc_hcchar.s.epdir = pipe->transfer_dir; - usbc_hcchar.s.epnum = pipe->endpoint_num; - usbc_hcchar.s.mps = pipe->max_packet; - cvmx_usb_write_csr32(usb, - CVMX_USBCX_HCCHARX(channel, usb->index), - usbc_hcchar.u32); - } - - /* Do transaction type specific fixups as needed */ - switch (transaction->type) { - case CVMX_USB_TRANSFER_CONTROL: - cvmx_usb_start_channel_control(usb, channel, pipe); - break; - case CVMX_USB_TRANSFER_BULK: - case CVMX_USB_TRANSFER_INTERRUPT: - break; - case CVMX_USB_TRANSFER_ISOCHRONOUS: - if (!cvmx_usb_pipe_needs_split(usb, pipe)) { - /* - * ISO transactions require different PIDs depending on - * direction and how many packets are needed - */ - if (pipe->transfer_dir == CVMX_USB_DIRECTION_OUT) { - if (pipe->multi_count < 2) /* Need DATA0 */ - USB_SET_FIELD32( - CVMX_USBCX_HCTSIZX(channel, - usb->index), - cvmx_usbcx_hctsizx, pid, 0); - else /* Need MDATA */ - USB_SET_FIELD32( - CVMX_USBCX_HCTSIZX(channel, - usb->index), - cvmx_usbcx_hctsizx, pid, 3); - } - } - break; - } - { - union cvmx_usbcx_hctsizx usbc_hctsiz = { .u32 = - cvmx_usb_read_csr32(usb, - CVMX_USBCX_HCTSIZX(channel, - usb->index)) - }; - transaction->xfersize = usbc_hctsiz.s.xfersize; - transaction->pktcnt = usbc_hctsiz.s.pktcnt; - } - /* Remember when we start a split transaction */ - if (cvmx_usb_pipe_needs_split(usb, pipe)) - usb->active_split = transaction; - USB_SET_FIELD32(CVMX_USBCX_HCCHARX(channel, usb->index), - cvmx_usbcx_hccharx, chena, 1); - if (usb->init_flags & CVMX_USB_INITIALIZE_FLAGS_NO_DMA) - cvmx_usb_fill_tx_fifo(usb, channel); -} - -/** - * Find a pipe that is ready to be scheduled to hardware. - * @usb: USB device state populated by cvmx_usb_initialize(). - * @xfer_type: Transfer type - * - * Returns: Pipe or NULL if none are ready - */ -static struct cvmx_usb_pipe *cvmx_usb_find_ready_pipe(struct octeon_hcd *usb, - enum cvmx_usb_transfer xfer_type) -{ - struct list_head *list = usb->active_pipes + xfer_type; - u64 current_frame = usb->frame_number; - struct cvmx_usb_pipe *pipe; - - list_for_each_entry(pipe, list, node) { - struct cvmx_usb_transaction *t = - list_first_entry(&pipe->transactions, typeof(*t), - node); - if (!(pipe->flags & CVMX_USB_PIPE_FLAGS_SCHEDULED) && t && - (pipe->next_tx_frame <= current_frame) && - ((pipe->split_sc_frame == -1) || - ((((int)current_frame - pipe->split_sc_frame) & 0x7f) < - 0x40)) && - (!usb->active_split || (usb->active_split == t))) { - prefetch(t); - return pipe; - } - } - return NULL; -} - -static struct cvmx_usb_pipe *cvmx_usb_next_pipe(struct octeon_hcd *usb, - int is_sof) -{ - struct cvmx_usb_pipe *pipe; - - /* Find a pipe needing service. */ - if (is_sof) { - /* - * Only process periodic pipes on SOF interrupts. This way we - * are sure that the periodic data is sent in the beginning of - * the frame. - */ - pipe = cvmx_usb_find_ready_pipe(usb, - CVMX_USB_TRANSFER_ISOCHRONOUS); - if (pipe) - return pipe; - pipe = cvmx_usb_find_ready_pipe(usb, - CVMX_USB_TRANSFER_INTERRUPT); - if (pipe) - return pipe; - } - pipe = cvmx_usb_find_ready_pipe(usb, CVMX_USB_TRANSFER_CONTROL); - if (pipe) - return pipe; - return cvmx_usb_find_ready_pipe(usb, CVMX_USB_TRANSFER_BULK); -} - -/** - * Called whenever a pipe might need to be scheduled to the - * hardware. - * - * @usb: USB device state populated by cvmx_usb_initialize(). - * @is_sof: True if this schedule was called on a SOF interrupt. - */ -static void cvmx_usb_schedule(struct octeon_hcd *usb, int is_sof) -{ - int channel; - struct cvmx_usb_pipe *pipe; - int need_sof; - enum cvmx_usb_transfer ttype; - - if (usb->init_flags & CVMX_USB_INITIALIZE_FLAGS_NO_DMA) { - /* - * Without DMA we need to be careful to not schedule something - * at the end of a frame and cause an overrun. - */ - union cvmx_usbcx_hfnum hfnum = { - .u32 = cvmx_usb_read_csr32(usb, - CVMX_USBCX_HFNUM(usb->index)) - }; - - union cvmx_usbcx_hfir hfir = { - .u32 = cvmx_usb_read_csr32(usb, - CVMX_USBCX_HFIR(usb->index)) - }; - - if (hfnum.s.frrem < hfir.s.frint / 4) - goto done; - } - - while (usb->idle_hardware_channels) { - /* Find an idle channel */ - channel = __fls(usb->idle_hardware_channels); - if (unlikely(channel > 7)) - break; - - pipe = cvmx_usb_next_pipe(usb, is_sof); - if (!pipe) - break; - - cvmx_usb_start_channel(usb, channel, pipe); - } - -done: - /* - * Only enable SOF interrupts when we have transactions pending in the - * future that might need to be scheduled - */ - need_sof = 0; - for (ttype = CVMX_USB_TRANSFER_CONTROL; - ttype <= CVMX_USB_TRANSFER_INTERRUPT; ttype++) { - list_for_each_entry(pipe, &usb->active_pipes[ttype], node) { - if (pipe->next_tx_frame > usb->frame_number) { - need_sof = 1; - break; - } - } - } - USB_SET_FIELD32(CVMX_USBCX_GINTMSK(usb->index), - cvmx_usbcx_gintmsk, sofmsk, need_sof); -} - -static void octeon_usb_urb_complete_callback(struct octeon_hcd *usb, - enum cvmx_usb_status status, - struct cvmx_usb_pipe *pipe, - struct cvmx_usb_transaction - *transaction, - int bytes_transferred, - struct urb *urb) -{ - struct usb_hcd *hcd = octeon_to_hcd(usb); - struct device *dev = hcd->self.controller; - - if (likely(status == CVMX_USB_STATUS_OK)) - urb->actual_length = bytes_transferred; - else - urb->actual_length = 0; - - urb->hcpriv = NULL; - - /* For Isochronous transactions we need to update the URB packet status - * list from data in our private copy - */ - if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) { - int i; - /* - * The pointer to the private list is stored in the setup_packet - * field. - */ - struct cvmx_usb_iso_packet *iso_packet = - (struct cvmx_usb_iso_packet *)urb->setup_packet; - /* Recalculate the transfer size by adding up each packet */ - urb->actual_length = 0; - for (i = 0; i < urb->number_of_packets; i++) { - if (iso_packet[i].status == CVMX_USB_STATUS_OK) { - urb->iso_frame_desc[i].status = 0; - urb->iso_frame_desc[i].actual_length = - iso_packet[i].length; - urb->actual_length += - urb->iso_frame_desc[i].actual_length; - } else { - dev_dbg(dev, "ISOCHRONOUS packet=%d of %d status=%d pipe=%p transaction=%p size=%d\n", - i, urb->number_of_packets, - iso_packet[i].status, pipe, - transaction, iso_packet[i].length); - urb->iso_frame_desc[i].status = -EREMOTEIO; - } - } - /* Free the private list now that we don't need it anymore */ - kfree(iso_packet); - urb->setup_packet = NULL; - } - - switch (status) { - case CVMX_USB_STATUS_OK: - urb->status = 0; - break; - case CVMX_USB_STATUS_CANCEL: - if (urb->status == 0) - urb->status = -ENOENT; - break; - case CVMX_USB_STATUS_STALL: - dev_dbg(dev, "status=stall pipe=%p transaction=%p size=%d\n", - pipe, transaction, bytes_transferred); - urb->status = -EPIPE; - break; - case CVMX_USB_STATUS_BABBLEERR: - dev_dbg(dev, "status=babble pipe=%p transaction=%p size=%d\n", - pipe, transaction, bytes_transferred); - urb->status = -EPIPE; - break; - case CVMX_USB_STATUS_SHORT: - dev_dbg(dev, "status=short pipe=%p transaction=%p size=%d\n", - pipe, transaction, bytes_transferred); - urb->status = -EREMOTEIO; - break; - case CVMX_USB_STATUS_ERROR: - case CVMX_USB_STATUS_XACTERR: - case CVMX_USB_STATUS_DATATGLERR: - case CVMX_USB_STATUS_FRAMEERR: - dev_dbg(dev, "status=%d pipe=%p transaction=%p size=%d\n", - status, pipe, transaction, bytes_transferred); - urb->status = -EPROTO; - break; - } - usb_hcd_unlink_urb_from_ep(octeon_to_hcd(usb), urb); - spin_unlock(&usb->lock); - usb_hcd_giveback_urb(octeon_to_hcd(usb), urb, urb->status); - spin_lock(&usb->lock); -} - -/** - * Signal the completion of a transaction and free it. The - * transaction will be removed from the pipe transaction list. - * - * @usb: USB device state populated by cvmx_usb_initialize(). - * @pipe: Pipe the transaction is on - * @transaction: - * Transaction that completed - * @complete_code: - * Completion code - */ -static void cvmx_usb_complete(struct octeon_hcd *usb, - struct cvmx_usb_pipe *pipe, - struct cvmx_usb_transaction *transaction, - enum cvmx_usb_status complete_code) -{ - /* If this was a split then clear our split in progress marker */ - if (usb->active_split == transaction) - usb->active_split = NULL; - - /* - * Isochronous transactions need extra processing as they might not be - * done after a single data transfer - */ - if (unlikely(transaction->type == CVMX_USB_TRANSFER_ISOCHRONOUS)) { - /* Update the number of bytes transferred in this ISO packet */ - transaction->iso_packets[0].length = transaction->actual_bytes; - transaction->iso_packets[0].status = complete_code; - - /* - * If there are more ISOs pending and we succeeded, schedule the - * next one - */ - if ((transaction->iso_number_packets > 1) && - (complete_code == CVMX_USB_STATUS_OK)) { - /* No bytes transferred for this packet as of yet */ - transaction->actual_bytes = 0; - /* One less ISO waiting to transfer */ - transaction->iso_number_packets--; - /* Increment to the next location in our packet array */ - transaction->iso_packets++; - transaction->stage = CVMX_USB_STAGE_NON_CONTROL; - return; - } - } - - /* Remove the transaction from the pipe list */ - list_del(&transaction->node); - if (list_empty(&pipe->transactions)) - list_move_tail(&pipe->node, &usb->idle_pipes); - octeon_usb_urb_complete_callback(usb, complete_code, pipe, - transaction, - transaction->actual_bytes, - transaction->urb); - kfree(transaction); -} - -/** - * Submit a usb transaction to a pipe. Called for all types - * of transactions. - * - * @usb: - * @pipe: Which pipe to submit to. - * @type: Transaction type - * @buffer: User buffer for the transaction - * @buffer_length: - * User buffer's length in bytes - * @control_header: - * For control transactions, the 8 byte standard header - * @iso_start_frame: - * For ISO transactions, the start frame - * @iso_number_packets: - * For ISO, the number of packet in the transaction. - * @iso_packets: - * A description of each ISO packet - * @urb: URB for the callback - * - * Returns: Transaction or NULL on failure. - */ -static struct cvmx_usb_transaction *cvmx_usb_submit_transaction( - struct octeon_hcd *usb, - struct cvmx_usb_pipe *pipe, - enum cvmx_usb_transfer type, - u64 buffer, - int buffer_length, - u64 control_header, - int iso_start_frame, - int iso_number_packets, - struct cvmx_usb_iso_packet *iso_packets, - struct urb *urb) -{ - struct cvmx_usb_transaction *transaction; - - if (unlikely(pipe->transfer_type != type)) - return NULL; - - transaction = kzalloc(sizeof(*transaction), GFP_ATOMIC); - if (unlikely(!transaction)) - return NULL; - - transaction->type = type; - transaction->buffer = buffer; - transaction->buffer_length = buffer_length; - transaction->control_header = control_header; - /* FIXME: This is not used, implement it. */ - transaction->iso_start_frame = iso_start_frame; - transaction->iso_number_packets = iso_number_packets; - transaction->iso_packets = iso_packets; - transaction->urb = urb; - if (transaction->type == CVMX_USB_TRANSFER_CONTROL) - transaction->stage = CVMX_USB_STAGE_SETUP; - else - transaction->stage = CVMX_USB_STAGE_NON_CONTROL; - - if (!list_empty(&pipe->transactions)) { - list_add_tail(&transaction->node, &pipe->transactions); - } else { - list_add_tail(&transaction->node, &pipe->transactions); - list_move_tail(&pipe->node, - &usb->active_pipes[pipe->transfer_type]); - - /* - * We may need to schedule the pipe if this was the head of the - * pipe. - */ - cvmx_usb_schedule(usb, 0); - } - - return transaction; -} - -/** - * Call to submit a USB Bulk transfer to a pipe. - * - * @usb: USB device state populated by cvmx_usb_initialize(). - * @pipe: Handle to the pipe for the transfer. - * @urb: URB. - * - * Returns: A submitted transaction or NULL on failure. - */ -static struct cvmx_usb_transaction *cvmx_usb_submit_bulk( - struct octeon_hcd *usb, - struct cvmx_usb_pipe *pipe, - struct urb *urb) -{ - return cvmx_usb_submit_transaction(usb, pipe, CVMX_USB_TRANSFER_BULK, - urb->transfer_dma, - urb->transfer_buffer_length, - 0, /* control_header */ - 0, /* iso_start_frame */ - 0, /* iso_number_packets */ - NULL, /* iso_packets */ - urb); -} - -/** - * Call to submit a USB Interrupt transfer to a pipe. - * - * @usb: USB device state populated by cvmx_usb_initialize(). - * @pipe: Handle to the pipe for the transfer. - * @urb: URB returned when the callback is called. - * - * Returns: A submitted transaction or NULL on failure. - */ -static struct cvmx_usb_transaction *cvmx_usb_submit_interrupt( - struct octeon_hcd *usb, - struct cvmx_usb_pipe *pipe, - struct urb *urb) -{ - return cvmx_usb_submit_transaction(usb, pipe, - CVMX_USB_TRANSFER_INTERRUPT, - urb->transfer_dma, - urb->transfer_buffer_length, - 0, /* control_header */ - 0, /* iso_start_frame */ - 0, /* iso_number_packets */ - NULL, /* iso_packets */ - urb); -} - -/** - * Call to submit a USB Control transfer to a pipe. - * - * @usb: USB device state populated by cvmx_usb_initialize(). - * @pipe: Handle to the pipe for the transfer. - * @urb: URB. - * - * Returns: A submitted transaction or NULL on failure. - */ -static struct cvmx_usb_transaction *cvmx_usb_submit_control( - struct octeon_hcd *usb, - struct cvmx_usb_pipe *pipe, - struct urb *urb) -{ - int buffer_length = urb->transfer_buffer_length; - u64 control_header = urb->setup_dma; - struct usb_ctrlrequest *header = cvmx_phys_to_ptr(control_header); - - if ((header->bRequestType & USB_DIR_IN) == 0) - buffer_length = le16_to_cpu(header->wLength); - - return cvmx_usb_submit_transaction(usb, pipe, - CVMX_USB_TRANSFER_CONTROL, - urb->transfer_dma, buffer_length, - control_header, - 0, /* iso_start_frame */ - 0, /* iso_number_packets */ - NULL, /* iso_packets */ - urb); -} - -/** - * Call to submit a USB Isochronous transfer to a pipe. - * - * @usb: USB device state populated by cvmx_usb_initialize(). - * @pipe: Handle to the pipe for the transfer. - * @urb: URB returned when the callback is called. - * - * Returns: A submitted transaction or NULL on failure. - */ -static struct cvmx_usb_transaction *cvmx_usb_submit_isochronous( - struct octeon_hcd *usb, - struct cvmx_usb_pipe *pipe, - struct urb *urb) -{ - struct cvmx_usb_iso_packet *packets; - - packets = (struct cvmx_usb_iso_packet *)urb->setup_packet; - return cvmx_usb_submit_transaction(usb, pipe, - CVMX_USB_TRANSFER_ISOCHRONOUS, - urb->transfer_dma, - urb->transfer_buffer_length, - 0, /* control_header */ - urb->start_frame, - urb->number_of_packets, - packets, urb); -} - -/** - * Cancel one outstanding request in a pipe. Canceling a request - * can fail if the transaction has already completed before cancel - * is called. Even after a successful cancel call, it may take - * a frame or two for the cvmx_usb_poll() function to call the - * associated callback. - * - * @usb: USB device state populated by cvmx_usb_initialize(). - * @pipe: Pipe to cancel requests in. - * @transaction: Transaction to cancel, returned by the submit function. - * - * Returns: 0 or a negative error code. - */ -static int cvmx_usb_cancel(struct octeon_hcd *usb, - struct cvmx_usb_pipe *pipe, - struct cvmx_usb_transaction *transaction) -{ - /* - * If the transaction is the HEAD of the queue and scheduled. We need to - * treat it special - */ - if (list_first_entry(&pipe->transactions, typeof(*transaction), node) == - transaction && (pipe->flags & CVMX_USB_PIPE_FLAGS_SCHEDULED)) { - union cvmx_usbcx_hccharx usbc_hcchar; - - usb->pipe_for_channel[pipe->channel] = NULL; - pipe->flags &= ~CVMX_USB_PIPE_FLAGS_SCHEDULED; - - CVMX_SYNCW; - - usbc_hcchar.u32 = cvmx_usb_read_csr32(usb, - CVMX_USBCX_HCCHARX(pipe->channel, usb->index)); - /* - * If the channel isn't enabled then the transaction already - * completed. - */ - if (usbc_hcchar.s.chena) { - usbc_hcchar.s.chdis = 1; - cvmx_usb_write_csr32(usb, - CVMX_USBCX_HCCHARX(pipe->channel, - usb->index), - usbc_hcchar.u32); - } - } - cvmx_usb_complete(usb, pipe, transaction, CVMX_USB_STATUS_CANCEL); - return 0; -} - -/** - * Cancel all outstanding requests in a pipe. Logically all this - * does is call cvmx_usb_cancel() in a loop. - * - * @usb: USB device state populated by cvmx_usb_initialize(). - * @pipe: Pipe to cancel requests in. - * - * Returns: 0 or a negative error code. - */ -static int cvmx_usb_cancel_all(struct octeon_hcd *usb, - struct cvmx_usb_pipe *pipe) -{ - struct cvmx_usb_transaction *transaction, *next; - - /* Simply loop through and attempt to cancel each transaction */ - list_for_each_entry_safe(transaction, next, &pipe->transactions, node) { - int result = cvmx_usb_cancel(usb, pipe, transaction); - - if (unlikely(result != 0)) - return result; - } - return 0; -} - -/** - * Close a pipe created with cvmx_usb_open_pipe(). - * - * @usb: USB device state populated by cvmx_usb_initialize(). - * @pipe: Pipe to close. - * - * Returns: 0 or a negative error code. EBUSY is returned if the pipe has - * outstanding transfers. - */ -static int cvmx_usb_close_pipe(struct octeon_hcd *usb, - struct cvmx_usb_pipe *pipe) -{ - /* Fail if the pipe has pending transactions */ - if (!list_empty(&pipe->transactions)) - return -EBUSY; - - list_del(&pipe->node); - kfree(pipe); - - return 0; -} - -/** - * Get the current USB protocol level frame number. The frame - * number is always in the range of 0-0x7ff. - * - * @usb: USB device state populated by cvmx_usb_initialize(). - * - * Returns: USB frame number - */ -static int cvmx_usb_get_frame_number(struct octeon_hcd *usb) -{ - union cvmx_usbcx_hfnum usbc_hfnum; - - usbc_hfnum.u32 = cvmx_usb_read_csr32(usb, CVMX_USBCX_HFNUM(usb->index)); - - return usbc_hfnum.s.frnum; -} - -static void cvmx_usb_transfer_control(struct octeon_hcd *usb, - struct cvmx_usb_pipe *pipe, - struct cvmx_usb_transaction *transaction, - union cvmx_usbcx_hccharx usbc_hcchar, - int buffer_space_left, - int bytes_in_last_packet) -{ - switch (transaction->stage) { - case CVMX_USB_STAGE_NON_CONTROL: - case CVMX_USB_STAGE_NON_CONTROL_SPLIT_COMPLETE: - /* This should be impossible */ - cvmx_usb_complete(usb, pipe, transaction, - CVMX_USB_STATUS_ERROR); - break; - case CVMX_USB_STAGE_SETUP: - pipe->pid_toggle = 1; - if (cvmx_usb_pipe_needs_split(usb, pipe)) { - transaction->stage = - CVMX_USB_STAGE_SETUP_SPLIT_COMPLETE; - } else { - struct usb_ctrlrequest *header = - cvmx_phys_to_ptr(transaction->control_header); - if (header->wLength) - transaction->stage = CVMX_USB_STAGE_DATA; - else - transaction->stage = CVMX_USB_STAGE_STATUS; - } - break; - case CVMX_USB_STAGE_SETUP_SPLIT_COMPLETE: - { - struct usb_ctrlrequest *header = - cvmx_phys_to_ptr(transaction->control_header); - if (header->wLength) - transaction->stage = CVMX_USB_STAGE_DATA; - else - transaction->stage = CVMX_USB_STAGE_STATUS; - } - break; - case CVMX_USB_STAGE_DATA: - if (cvmx_usb_pipe_needs_split(usb, pipe)) { - transaction->stage = CVMX_USB_STAGE_DATA_SPLIT_COMPLETE; - /* - * For setup OUT data that are splits, - * the hardware doesn't appear to count - * transferred data. Here we manually - * update the data transferred - */ - if (!usbc_hcchar.s.epdir) { - if (buffer_space_left < pipe->max_packet) - transaction->actual_bytes += - buffer_space_left; - else - transaction->actual_bytes += - pipe->max_packet; - } - } else if ((buffer_space_left == 0) || - (bytes_in_last_packet < pipe->max_packet)) { - pipe->pid_toggle = 1; - transaction->stage = CVMX_USB_STAGE_STATUS; - } - break; - case CVMX_USB_STAGE_DATA_SPLIT_COMPLETE: - if ((buffer_space_left == 0) || - (bytes_in_last_packet < pipe->max_packet)) { - pipe->pid_toggle = 1; - transaction->stage = CVMX_USB_STAGE_STATUS; - } else { - transaction->stage = CVMX_USB_STAGE_DATA; - } - break; - case CVMX_USB_STAGE_STATUS: - if (cvmx_usb_pipe_needs_split(usb, pipe)) - transaction->stage = - CVMX_USB_STAGE_STATUS_SPLIT_COMPLETE; - else - cvmx_usb_complete(usb, pipe, transaction, - CVMX_USB_STATUS_OK); - break; - case CVMX_USB_STAGE_STATUS_SPLIT_COMPLETE: - cvmx_usb_complete(usb, pipe, transaction, CVMX_USB_STATUS_OK); - break; - } -} - -static void cvmx_usb_transfer_bulk(struct octeon_hcd *usb, - struct cvmx_usb_pipe *pipe, - struct cvmx_usb_transaction *transaction, - union cvmx_usbcx_hcintx usbc_hcint, - int buffer_space_left, - int bytes_in_last_packet) -{ - /* - * The only time a bulk transfer isn't complete when it finishes with - * an ACK is during a split transaction. For splits we need to continue - * the transfer if more data is needed. - */ - if (cvmx_usb_pipe_needs_split(usb, pipe)) { - if (transaction->stage == CVMX_USB_STAGE_NON_CONTROL) - transaction->stage = - CVMX_USB_STAGE_NON_CONTROL_SPLIT_COMPLETE; - else if (buffer_space_left && - (bytes_in_last_packet == pipe->max_packet)) - transaction->stage = CVMX_USB_STAGE_NON_CONTROL; - else - cvmx_usb_complete(usb, pipe, transaction, - CVMX_USB_STATUS_OK); - } else { - if ((pipe->device_speed == CVMX_USB_SPEED_HIGH) && - (pipe->transfer_dir == CVMX_USB_DIRECTION_OUT) && - (usbc_hcint.s.nak)) - pipe->flags |= CVMX_USB_PIPE_FLAGS_NEED_PING; - if (!buffer_space_left || - (bytes_in_last_packet < pipe->max_packet)) - cvmx_usb_complete(usb, pipe, transaction, - CVMX_USB_STATUS_OK); - } -} - -static void cvmx_usb_transfer_intr(struct octeon_hcd *usb, - struct cvmx_usb_pipe *pipe, - struct cvmx_usb_transaction *transaction, - int buffer_space_left, - int bytes_in_last_packet) -{ - if (cvmx_usb_pipe_needs_split(usb, pipe)) { - if (transaction->stage == CVMX_USB_STAGE_NON_CONTROL) { - transaction->stage = - CVMX_USB_STAGE_NON_CONTROL_SPLIT_COMPLETE; - } else if (buffer_space_left && - (bytes_in_last_packet == pipe->max_packet)) { - transaction->stage = CVMX_USB_STAGE_NON_CONTROL; - } else { - pipe->next_tx_frame += pipe->interval; - cvmx_usb_complete(usb, pipe, transaction, - CVMX_USB_STATUS_OK); - } - } else if (!buffer_space_left || - (bytes_in_last_packet < pipe->max_packet)) { - pipe->next_tx_frame += pipe->interval; - cvmx_usb_complete(usb, pipe, transaction, CVMX_USB_STATUS_OK); - } -} - -static void cvmx_usb_transfer_isoc(struct octeon_hcd *usb, - struct cvmx_usb_pipe *pipe, - struct cvmx_usb_transaction *transaction, - int buffer_space_left, - int bytes_in_last_packet, - int bytes_this_transfer) -{ - if (cvmx_usb_pipe_needs_split(usb, pipe)) { - /* - * ISOCHRONOUS OUT splits don't require a complete split stage. - * Instead they use a sequence of begin OUT splits to transfer - * the data 188 bytes at a time. Once the transfer is complete, - * the pipe sleeps until the next schedule interval. - */ - if (pipe->transfer_dir == CVMX_USB_DIRECTION_OUT) { - /* - * If no space left or this wasn't a max size packet - * then this transfer is complete. Otherwise start it - * again to send the next 188 bytes - */ - if (!buffer_space_left || (bytes_this_transfer < 188)) { - pipe->next_tx_frame += pipe->interval; - cvmx_usb_complete(usb, pipe, transaction, - CVMX_USB_STATUS_OK); - } - return; - } - if (transaction->stage == - CVMX_USB_STAGE_NON_CONTROL_SPLIT_COMPLETE) { - /* - * We are in the incoming data phase. Keep getting data - * until we run out of space or get a small packet - */ - if ((buffer_space_left == 0) || - (bytes_in_last_packet < pipe->max_packet)) { - pipe->next_tx_frame += pipe->interval; - cvmx_usb_complete(usb, pipe, transaction, - CVMX_USB_STATUS_OK); - } - } else { - transaction->stage = - CVMX_USB_STAGE_NON_CONTROL_SPLIT_COMPLETE; - } - } else { - pipe->next_tx_frame += pipe->interval; - cvmx_usb_complete(usb, pipe, transaction, CVMX_USB_STATUS_OK); - } -} - -/** - * Poll a channel for status - * - * @usb: USB device - * @channel: Channel to poll - * - * Returns: Zero on success - */ -static int cvmx_usb_poll_channel(struct octeon_hcd *usb, int channel) -{ - struct usb_hcd *hcd = octeon_to_hcd(usb); - struct device *dev = hcd->self.controller; - union cvmx_usbcx_hcintx usbc_hcint; - union cvmx_usbcx_hctsizx usbc_hctsiz; - union cvmx_usbcx_hccharx usbc_hcchar; - struct cvmx_usb_pipe *pipe; - struct cvmx_usb_transaction *transaction; - int bytes_this_transfer; - int bytes_in_last_packet; - int packets_processed; - int buffer_space_left; - - /* Read the interrupt status bits for the channel */ - usbc_hcint.u32 = cvmx_usb_read_csr32(usb, - CVMX_USBCX_HCINTX(channel, usb->index)); - - if (usb->init_flags & CVMX_USB_INITIALIZE_FLAGS_NO_DMA) { - usbc_hcchar.u32 = cvmx_usb_read_csr32(usb, - CVMX_USBCX_HCCHARX(channel, usb->index)); - - if (usbc_hcchar.s.chena && usbc_hcchar.s.chdis) { - /* - * There seems to be a bug in CN31XX which can cause - * interrupt IN transfers to get stuck until we do a - * write of HCCHARX without changing things - */ - cvmx_usb_write_csr32(usb, - CVMX_USBCX_HCCHARX(channel, - usb->index), - usbc_hcchar.u32); - return 0; - } - - /* - * In non DMA mode the channels don't halt themselves. We need - * to manually disable channels that are left running - */ - if (!usbc_hcint.s.chhltd) { - if (usbc_hcchar.s.chena) { - union cvmx_usbcx_hcintmskx hcintmsk; - /* Disable all interrupts except CHHLTD */ - hcintmsk.u32 = 0; - hcintmsk.s.chhltdmsk = 1; - cvmx_usb_write_csr32(usb, - CVMX_USBCX_HCINTMSKX(channel, usb->index), - hcintmsk.u32); - usbc_hcchar.s.chdis = 1; - cvmx_usb_write_csr32(usb, - CVMX_USBCX_HCCHARX(channel, usb->index), - usbc_hcchar.u32); - return 0; - } else if (usbc_hcint.s.xfercompl) { - /* - * Successful IN/OUT with transfer complete. - * Channel halt isn't needed. - */ - } else { - dev_err(dev, "USB%d: Channel %d interrupt without halt\n", - usb->index, channel); - return 0; - } - } - } else { - /* - * There is are no interrupts that we need to process when the - * channel is still running - */ - if (!usbc_hcint.s.chhltd) - return 0; - } - - /* Disable the channel interrupts now that it is done */ - cvmx_usb_write_csr32(usb, CVMX_USBCX_HCINTMSKX(channel, usb->index), 0); - usb->idle_hardware_channels |= (1 << channel); - - /* Make sure this channel is tied to a valid pipe */ - pipe = usb->pipe_for_channel[channel]; - prefetch(pipe); - if (!pipe) - return 0; - transaction = list_first_entry(&pipe->transactions, - typeof(*transaction), - node); - prefetch(transaction); - - /* - * Disconnect this pipe from the HW channel. Later the schedule - * function will figure out which pipe needs to go - */ - usb->pipe_for_channel[channel] = NULL; - pipe->flags &= ~CVMX_USB_PIPE_FLAGS_SCHEDULED; - - /* - * Read the channel config info so we can figure out how much data - * transferred - */ - usbc_hcchar.u32 = cvmx_usb_read_csr32(usb, - CVMX_USBCX_HCCHARX(channel, usb->index)); - usbc_hctsiz.u32 = cvmx_usb_read_csr32(usb, - CVMX_USBCX_HCTSIZX(channel, usb->index)); - - /* - * Calculating the number of bytes successfully transferred is dependent - * on the transfer direction - */ - packets_processed = transaction->pktcnt - usbc_hctsiz.s.pktcnt; - if (usbc_hcchar.s.epdir) { - /* - * IN transactions are easy. For every byte received the - * hardware decrements xfersize. All we need to do is subtract - * the current value of xfersize from its starting value and we - * know how many bytes were written to the buffer - */ - bytes_this_transfer = transaction->xfersize - - usbc_hctsiz.s.xfersize; - } else { - /* - * OUT transaction don't decrement xfersize. Instead pktcnt is - * decremented on every successful packet send. The hardware - * does this when it receives an ACK, or NYET. If it doesn't - * receive one of these responses pktcnt doesn't change - */ - bytes_this_transfer = packets_processed * usbc_hcchar.s.mps; - /* - * The last packet may not be a full transfer if we didn't have - * enough data - */ - if (bytes_this_transfer > transaction->xfersize) - bytes_this_transfer = transaction->xfersize; - } - /* Figure out how many bytes were in the last packet of the transfer */ - if (packets_processed) - bytes_in_last_packet = bytes_this_transfer - - (packets_processed - 1) * usbc_hcchar.s.mps; - else - bytes_in_last_packet = bytes_this_transfer; - - /* - * As a special case, setup transactions output the setup header, not - * the user's data. For this reason we don't count setup data as bytes - * transferred - */ - if ((transaction->stage == CVMX_USB_STAGE_SETUP) || - (transaction->stage == CVMX_USB_STAGE_SETUP_SPLIT_COMPLETE)) - bytes_this_transfer = 0; - - /* - * Add the bytes transferred to the running total. It is important that - * bytes_this_transfer doesn't count any data that needs to be - * retransmitted - */ - transaction->actual_bytes += bytes_this_transfer; - if (transaction->type == CVMX_USB_TRANSFER_ISOCHRONOUS) - buffer_space_left = transaction->iso_packets[0].length - - transaction->actual_bytes; - else - buffer_space_left = transaction->buffer_length - - transaction->actual_bytes; - - /* - * We need to remember the PID toggle state for the next transaction. - * The hardware already updated it for the next transaction - */ - pipe->pid_toggle = !(usbc_hctsiz.s.pid == 0); - - /* - * For high speed bulk out, assume the next transaction will need to do - * a ping before proceeding. If this isn't true the ACK processing below - * will clear this flag - */ - if ((pipe->device_speed == CVMX_USB_SPEED_HIGH) && - (pipe->transfer_type == CVMX_USB_TRANSFER_BULK) && - (pipe->transfer_dir == CVMX_USB_DIRECTION_OUT)) - pipe->flags |= CVMX_USB_PIPE_FLAGS_NEED_PING; - - if (WARN_ON_ONCE(bytes_this_transfer < 0)) { - /* - * In some rare cases the DMA engine seems to get stuck and - * keeps substracting same byte count over and over again. In - * such case we just need to fail every transaction. - */ - cvmx_usb_complete(usb, pipe, transaction, - CVMX_USB_STATUS_ERROR); - return 0; - } - - if (usbc_hcint.s.stall) { - /* - * STALL as a response means this transaction cannot be - * completed because the device can't process transactions. Tell - * the user. Any data that was transferred will be counted on - * the actual bytes transferred - */ - pipe->pid_toggle = 0; - cvmx_usb_complete(usb, pipe, transaction, - CVMX_USB_STATUS_STALL); - } else if (usbc_hcint.s.xacterr) { - /* - * XactErr as a response means the device signaled - * something wrong with the transfer. For example, PID - * toggle errors cause these. - */ - cvmx_usb_complete(usb, pipe, transaction, - CVMX_USB_STATUS_XACTERR); - } else if (usbc_hcint.s.bblerr) { - /* Babble Error (BblErr) */ - cvmx_usb_complete(usb, pipe, transaction, - CVMX_USB_STATUS_BABBLEERR); - } else if (usbc_hcint.s.datatglerr) { - /* Data toggle error */ - cvmx_usb_complete(usb, pipe, transaction, - CVMX_USB_STATUS_DATATGLERR); - } else if (usbc_hcint.s.nyet) { - /* - * NYET as a response is only allowed in three cases: as a - * response to a ping, as a response to a split transaction, and - * as a response to a bulk out. The ping case is handled by - * hardware, so we only have splits and bulk out - */ - if (!cvmx_usb_pipe_needs_split(usb, pipe)) { - transaction->retries = 0; - /* - * If there is more data to go then we need to try - * again. Otherwise this transaction is complete - */ - if ((buffer_space_left == 0) || - (bytes_in_last_packet < pipe->max_packet)) - cvmx_usb_complete(usb, pipe, - transaction, - CVMX_USB_STATUS_OK); - } else { - /* - * Split transactions retry the split complete 4 times - * then rewind to the start split and do the entire - * transactions again - */ - transaction->retries++; - if ((transaction->retries & 0x3) == 0) { - /* - * Rewind to the beginning of the transaction by - * anding off the split complete bit - */ - transaction->stage &= ~1; - pipe->split_sc_frame = -1; - } - } - } else if (usbc_hcint.s.ack) { - transaction->retries = 0; - /* - * The ACK bit can only be checked after the other error bits. - * This is because a multi packet transfer may succeed in a - * number of packets and then get a different response on the - * last packet. In this case both ACK and the last response bit - * will be set. If none of the other response bits is set, then - * the last packet must have been an ACK - * - * Since we got an ACK, we know we don't need to do a ping on - * this pipe - */ - pipe->flags &= ~CVMX_USB_PIPE_FLAGS_NEED_PING; - - switch (transaction->type) { - case CVMX_USB_TRANSFER_CONTROL: - cvmx_usb_transfer_control(usb, pipe, transaction, - usbc_hcchar, - buffer_space_left, - bytes_in_last_packet); - break; - case CVMX_USB_TRANSFER_BULK: - cvmx_usb_transfer_bulk(usb, pipe, transaction, - usbc_hcint, buffer_space_left, - bytes_in_last_packet); - break; - case CVMX_USB_TRANSFER_INTERRUPT: - cvmx_usb_transfer_intr(usb, pipe, transaction, - buffer_space_left, - bytes_in_last_packet); - break; - case CVMX_USB_TRANSFER_ISOCHRONOUS: - cvmx_usb_transfer_isoc(usb, pipe, transaction, - buffer_space_left, - bytes_in_last_packet, - bytes_this_transfer); - break; - } - } else if (usbc_hcint.s.nak) { - /* - * If this was a split then clear our split in progress marker. - */ - if (usb->active_split == transaction) - usb->active_split = NULL; - /* - * NAK as a response means the device couldn't accept the - * transaction, but it should be retried in the future. Rewind - * to the beginning of the transaction by anding off the split - * complete bit. Retry in the next interval - */ - transaction->retries = 0; - transaction->stage &= ~1; - pipe->next_tx_frame += pipe->interval; - if (pipe->next_tx_frame < usb->frame_number) - pipe->next_tx_frame = usb->frame_number + - pipe->interval - - (usb->frame_number - pipe->next_tx_frame) % - pipe->interval; - } else { - struct cvmx_usb_port_status port; - - port = cvmx_usb_get_status(usb); - if (port.port_enabled) { - /* We'll retry the exact same transaction again */ - transaction->retries++; - } else { - /* - * We get channel halted interrupts with no result bits - * sets when the cable is unplugged - */ - cvmx_usb_complete(usb, pipe, transaction, - CVMX_USB_STATUS_ERROR); - } - } - return 0; -} - -static void octeon_usb_port_callback(struct octeon_hcd *usb) -{ - spin_unlock(&usb->lock); - usb_hcd_poll_rh_status(octeon_to_hcd(usb)); - spin_lock(&usb->lock); -} - -/** - * Poll the USB block for status and call all needed callback - * handlers. This function is meant to be called in the interrupt - * handler for the USB controller. It can also be called - * periodically in a loop for non-interrupt based operation. - * - * @usb: USB device state populated by cvmx_usb_initialize(). - * - * Returns: 0 or a negative error code. - */ -static int cvmx_usb_poll(struct octeon_hcd *usb) -{ - union cvmx_usbcx_hfnum usbc_hfnum; - union cvmx_usbcx_gintsts usbc_gintsts; - - prefetch_range(usb, sizeof(*usb)); - - /* Update the frame counter */ - usbc_hfnum.u32 = cvmx_usb_read_csr32(usb, CVMX_USBCX_HFNUM(usb->index)); - if ((usb->frame_number & 0x3fff) > usbc_hfnum.s.frnum) - usb->frame_number += 0x4000; - usb->frame_number &= ~0x3fffull; - usb->frame_number |= usbc_hfnum.s.frnum; - - /* Read the pending interrupts */ - usbc_gintsts.u32 = cvmx_usb_read_csr32(usb, - CVMX_USBCX_GINTSTS(usb->index)); - - /* Clear the interrupts now that we know about them */ - cvmx_usb_write_csr32(usb, CVMX_USBCX_GINTSTS(usb->index), - usbc_gintsts.u32); - - if (usbc_gintsts.s.rxflvl) { - /* - * RxFIFO Non-Empty (RxFLvl) - * Indicates that there is at least one packet pending to be - * read from the RxFIFO. - * - * In DMA mode this is handled by hardware - */ - if (usb->init_flags & CVMX_USB_INITIALIZE_FLAGS_NO_DMA) - cvmx_usb_poll_rx_fifo(usb); - } - if (usbc_gintsts.s.ptxfemp || usbc_gintsts.s.nptxfemp) { - /* Fill the Tx FIFOs when not in DMA mode */ - if (usb->init_flags & CVMX_USB_INITIALIZE_FLAGS_NO_DMA) - cvmx_usb_poll_tx_fifo(usb); - } - if (usbc_gintsts.s.disconnint || usbc_gintsts.s.prtint) { - union cvmx_usbcx_hprt usbc_hprt; - /* - * Disconnect Detected Interrupt (DisconnInt) - * Asserted when a device disconnect is detected. - * - * Host Port Interrupt (PrtInt) - * The core sets this bit to indicate a change in port status of - * one of the O2P USB core ports in Host mode. The application - * must read the Host Port Control and Status (HPRT) register to - * determine the exact event that caused this interrupt. The - * application must clear the appropriate status bit in the Host - * Port Control and Status register to clear this bit. - * - * Call the user's port callback - */ - octeon_usb_port_callback(usb); - /* Clear the port change bits */ - usbc_hprt.u32 = - cvmx_usb_read_csr32(usb, CVMX_USBCX_HPRT(usb->index)); - usbc_hprt.s.prtena = 0; - cvmx_usb_write_csr32(usb, CVMX_USBCX_HPRT(usb->index), - usbc_hprt.u32); - } - if (usbc_gintsts.s.hchint) { - /* - * Host Channels Interrupt (HChInt) - * The core sets this bit to indicate that an interrupt is - * pending on one of the channels of the core (in Host mode). - * The application must read the Host All Channels Interrupt - * (HAINT) register to determine the exact number of the channel - * on which the interrupt occurred, and then read the - * corresponding Host Channel-n Interrupt (HCINTn) register to - * determine the exact cause of the interrupt. The application - * must clear the appropriate status bit in the HCINTn register - * to clear this bit. - */ - union cvmx_usbcx_haint usbc_haint; - - usbc_haint.u32 = cvmx_usb_read_csr32(usb, - CVMX_USBCX_HAINT(usb->index)); - while (usbc_haint.u32) { - int channel; - - channel = __fls(usbc_haint.u32); - cvmx_usb_poll_channel(usb, channel); - usbc_haint.u32 ^= 1 << channel; - } - } - - cvmx_usb_schedule(usb, usbc_gintsts.s.sof); - - return 0; -} - -/* convert between an HCD pointer and the corresponding struct octeon_hcd */ -static inline struct octeon_hcd *hcd_to_octeon(struct usb_hcd *hcd) -{ - return (struct octeon_hcd *)(hcd->hcd_priv); -} - -static irqreturn_t octeon_usb_irq(struct usb_hcd *hcd) -{ - struct octeon_hcd *usb = hcd_to_octeon(hcd); - unsigned long flags; - - spin_lock_irqsave(&usb->lock, flags); - cvmx_usb_poll(usb); - spin_unlock_irqrestore(&usb->lock, flags); - return IRQ_HANDLED; -} - -static int octeon_usb_start(struct usb_hcd *hcd) -{ - hcd->state = HC_STATE_RUNNING; - return 0; -} - -static void octeon_usb_stop(struct usb_hcd *hcd) -{ - hcd->state = HC_STATE_HALT; -} - -static int octeon_usb_get_frame_number(struct usb_hcd *hcd) -{ - struct octeon_hcd *usb = hcd_to_octeon(hcd); - - return cvmx_usb_get_frame_number(usb); -} - -static int octeon_usb_urb_enqueue(struct usb_hcd *hcd, - struct urb *urb, - gfp_t mem_flags) -{ - struct octeon_hcd *usb = hcd_to_octeon(hcd); - struct device *dev = hcd->self.controller; - struct cvmx_usb_transaction *transaction = NULL; - struct cvmx_usb_pipe *pipe; - unsigned long flags; - struct cvmx_usb_iso_packet *iso_packet; - struct usb_host_endpoint *ep = urb->ep; - int rc; - - urb->status = 0; - spin_lock_irqsave(&usb->lock, flags); - - rc = usb_hcd_link_urb_to_ep(hcd, urb); - if (rc) { - spin_unlock_irqrestore(&usb->lock, flags); - return rc; - } - - if (!ep->hcpriv) { - enum cvmx_usb_transfer transfer_type; - enum cvmx_usb_speed speed; - int split_device = 0; - int split_port = 0; - - switch (usb_pipetype(urb->pipe)) { - case PIPE_ISOCHRONOUS: - transfer_type = CVMX_USB_TRANSFER_ISOCHRONOUS; - break; - case PIPE_INTERRUPT: - transfer_type = CVMX_USB_TRANSFER_INTERRUPT; - break; - case PIPE_CONTROL: - transfer_type = CVMX_USB_TRANSFER_CONTROL; - break; - default: - transfer_type = CVMX_USB_TRANSFER_BULK; - break; - } - switch (urb->dev->speed) { - case USB_SPEED_LOW: - speed = CVMX_USB_SPEED_LOW; - break; - case USB_SPEED_FULL: - speed = CVMX_USB_SPEED_FULL; - break; - default: - speed = CVMX_USB_SPEED_HIGH; - break; - } - /* - * For slow devices on high speed ports we need to find the hub - * that does the speed translation so we know where to send the - * split transactions. - */ - if (speed != CVMX_USB_SPEED_HIGH) { - /* - * Start at this device and work our way up the usb - * tree. - */ - struct usb_device *dev = urb->dev; - - while (dev->parent) { - /* - * If our parent is high speed then he'll - * receive the splits. - */ - if (dev->parent->speed == USB_SPEED_HIGH) { - split_device = dev->parent->devnum; - split_port = dev->portnum; - break; - } - /* - * Move up the tree one level. If we make it all - * the way up the tree, then the port must not - * be in high speed mode and we don't need a - * split. - */ - dev = dev->parent; - } - } - pipe = cvmx_usb_open_pipe(usb, usb_pipedevice(urb->pipe), - usb_pipeendpoint(urb->pipe), speed, - le16_to_cpu(ep->desc.wMaxPacketSize) - & 0x7ff, - transfer_type, - usb_pipein(urb->pipe) ? - CVMX_USB_DIRECTION_IN : - CVMX_USB_DIRECTION_OUT, - urb->interval, - (le16_to_cpu(ep->desc.wMaxPacketSize) - >> 11) & 0x3, - split_device, split_port); - if (!pipe) { - usb_hcd_unlink_urb_from_ep(hcd, urb); - spin_unlock_irqrestore(&usb->lock, flags); - dev_dbg(dev, "Failed to create pipe\n"); - return -ENOMEM; - } - ep->hcpriv = pipe; - } else { - pipe = ep->hcpriv; - } - - switch (usb_pipetype(urb->pipe)) { - case PIPE_ISOCHRONOUS: - dev_dbg(dev, "Submit isochronous to %d.%d\n", - usb_pipedevice(urb->pipe), - usb_pipeendpoint(urb->pipe)); - /* - * Allocate a structure to use for our private list of - * isochronous packets. - */ - iso_packet = kmalloc_array(urb->number_of_packets, - sizeof(struct cvmx_usb_iso_packet), - GFP_ATOMIC); - if (iso_packet) { - int i; - /* Fill the list with the data from the URB */ - for (i = 0; i < urb->number_of_packets; i++) { - iso_packet[i].offset = - urb->iso_frame_desc[i].offset; - iso_packet[i].length = - urb->iso_frame_desc[i].length; - iso_packet[i].status = CVMX_USB_STATUS_ERROR; - } - /* - * Store a pointer to the list in the URB setup_packet - * field. We know this currently isn't being used and - * this saves us a bunch of logic. - */ - urb->setup_packet = (char *)iso_packet; - transaction = cvmx_usb_submit_isochronous(usb, - pipe, urb); - /* - * If submit failed we need to free our private packet - * list. - */ - if (!transaction) { - urb->setup_packet = NULL; - kfree(iso_packet); - } - } - break; - case PIPE_INTERRUPT: - dev_dbg(dev, "Submit interrupt to %d.%d\n", - usb_pipedevice(urb->pipe), - usb_pipeendpoint(urb->pipe)); - transaction = cvmx_usb_submit_interrupt(usb, pipe, urb); - break; - case PIPE_CONTROL: - dev_dbg(dev, "Submit control to %d.%d\n", - usb_pipedevice(urb->pipe), - usb_pipeendpoint(urb->pipe)); - transaction = cvmx_usb_submit_control(usb, pipe, urb); - break; - case PIPE_BULK: - dev_dbg(dev, "Submit bulk to %d.%d\n", - usb_pipedevice(urb->pipe), - usb_pipeendpoint(urb->pipe)); - transaction = cvmx_usb_submit_bulk(usb, pipe, urb); - break; - } - if (!transaction) { - usb_hcd_unlink_urb_from_ep(hcd, urb); - spin_unlock_irqrestore(&usb->lock, flags); - dev_dbg(dev, "Failed to submit\n"); - return -ENOMEM; - } - urb->hcpriv = transaction; - spin_unlock_irqrestore(&usb->lock, flags); - return 0; -} - -static int octeon_usb_urb_dequeue(struct usb_hcd *hcd, - struct urb *urb, - int status) -{ - struct octeon_hcd *usb = hcd_to_octeon(hcd); - unsigned long flags; - int rc; - - if (!urb->dev) - return -EINVAL; - - spin_lock_irqsave(&usb->lock, flags); - - rc = usb_hcd_check_unlink_urb(hcd, urb, status); - if (rc) - goto out; - - urb->status = status; - cvmx_usb_cancel(usb, urb->ep->hcpriv, urb->hcpriv); - -out: - spin_unlock_irqrestore(&usb->lock, flags); - - return rc; -} - -static void octeon_usb_endpoint_disable(struct usb_hcd *hcd, - struct usb_host_endpoint *ep) -{ - struct device *dev = hcd->self.controller; - - if (ep->hcpriv) { - struct octeon_hcd *usb = hcd_to_octeon(hcd); - struct cvmx_usb_pipe *pipe = ep->hcpriv; - unsigned long flags; - - spin_lock_irqsave(&usb->lock, flags); - cvmx_usb_cancel_all(usb, pipe); - if (cvmx_usb_close_pipe(usb, pipe)) - dev_dbg(dev, "Closing pipe %p failed\n", pipe); - spin_unlock_irqrestore(&usb->lock, flags); - ep->hcpriv = NULL; - } -} - -static int octeon_usb_hub_status_data(struct usb_hcd *hcd, char *buf) -{ - struct octeon_hcd *usb = hcd_to_octeon(hcd); - struct cvmx_usb_port_status port_status; - unsigned long flags; - - spin_lock_irqsave(&usb->lock, flags); - port_status = cvmx_usb_get_status(usb); - spin_unlock_irqrestore(&usb->lock, flags); - buf[0] = port_status.connect_change << 1; - - return buf[0] != 0; -} - -static int octeon_usb_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, - u16 wIndex, char *buf, u16 wLength) -{ - struct octeon_hcd *usb = hcd_to_octeon(hcd); - struct device *dev = hcd->self.controller; - struct cvmx_usb_port_status usb_port_status; - int port_status; - struct usb_hub_descriptor *desc; - unsigned long flags; - - switch (typeReq) { - case ClearHubFeature: - dev_dbg(dev, "ClearHubFeature\n"); - switch (wValue) { - case C_HUB_LOCAL_POWER: - case C_HUB_OVER_CURRENT: - /* Nothing required here */ - break; - default: - return -EINVAL; - } - break; - case ClearPortFeature: - dev_dbg(dev, "ClearPortFeature\n"); - if (wIndex != 1) { - dev_dbg(dev, " INVALID\n"); - return -EINVAL; - } - - switch (wValue) { - case USB_PORT_FEAT_ENABLE: - dev_dbg(dev, " ENABLE\n"); - spin_lock_irqsave(&usb->lock, flags); - cvmx_usb_disable(usb); - spin_unlock_irqrestore(&usb->lock, flags); - break; - case USB_PORT_FEAT_SUSPEND: - dev_dbg(dev, " SUSPEND\n"); - /* Not supported on Octeon */ - break; - case USB_PORT_FEAT_POWER: - dev_dbg(dev, " POWER\n"); - /* Not supported on Octeon */ - break; - case USB_PORT_FEAT_INDICATOR: - dev_dbg(dev, " INDICATOR\n"); - /* Port inidicator not supported */ - break; - case USB_PORT_FEAT_C_CONNECTION: - dev_dbg(dev, " C_CONNECTION\n"); - /* Clears drivers internal connect status change flag */ - spin_lock_irqsave(&usb->lock, flags); - usb->port_status = cvmx_usb_get_status(usb); - spin_unlock_irqrestore(&usb->lock, flags); - break; - case USB_PORT_FEAT_C_RESET: - dev_dbg(dev, " C_RESET\n"); - /* - * Clears the driver's internal Port Reset Change flag. - */ - spin_lock_irqsave(&usb->lock, flags); - usb->port_status = cvmx_usb_get_status(usb); - spin_unlock_irqrestore(&usb->lock, flags); - break; - case USB_PORT_FEAT_C_ENABLE: - dev_dbg(dev, " C_ENABLE\n"); - /* - * Clears the driver's internal Port Enable/Disable - * Change flag. - */ - spin_lock_irqsave(&usb->lock, flags); - usb->port_status = cvmx_usb_get_status(usb); - spin_unlock_irqrestore(&usb->lock, flags); - break; - case USB_PORT_FEAT_C_SUSPEND: - dev_dbg(dev, " C_SUSPEND\n"); - /* - * Clears the driver's internal Port Suspend Change - * flag, which is set when resume signaling on the host - * port is complete. - */ - break; - case USB_PORT_FEAT_C_OVER_CURRENT: - dev_dbg(dev, " C_OVER_CURRENT\n"); - /* Clears the driver's overcurrent Change flag */ - spin_lock_irqsave(&usb->lock, flags); - usb->port_status = cvmx_usb_get_status(usb); - spin_unlock_irqrestore(&usb->lock, flags); - break; - default: - dev_dbg(dev, " UNKNOWN\n"); - return -EINVAL; - } - break; - case GetHubDescriptor: - dev_dbg(dev, "GetHubDescriptor\n"); - desc = (struct usb_hub_descriptor *)buf; - desc->bDescLength = 9; - desc->bDescriptorType = 0x29; - desc->bNbrPorts = 1; - desc->wHubCharacteristics = cpu_to_le16(0x08); - desc->bPwrOn2PwrGood = 1; - desc->bHubContrCurrent = 0; - desc->u.hs.DeviceRemovable[0] = 0; - desc->u.hs.DeviceRemovable[1] = 0xff; - break; - case GetHubStatus: - dev_dbg(dev, "GetHubStatus\n"); - *(__le32 *)buf = 0; - break; - case GetPortStatus: - dev_dbg(dev, "GetPortStatus\n"); - if (wIndex != 1) { - dev_dbg(dev, " INVALID\n"); - return -EINVAL; - } - - spin_lock_irqsave(&usb->lock, flags); - usb_port_status = cvmx_usb_get_status(usb); - spin_unlock_irqrestore(&usb->lock, flags); - port_status = 0; - - if (usb_port_status.connect_change) { - port_status |= (1 << USB_PORT_FEAT_C_CONNECTION); - dev_dbg(dev, " C_CONNECTION\n"); - } - - if (usb_port_status.port_enabled) { - port_status |= (1 << USB_PORT_FEAT_C_ENABLE); - dev_dbg(dev, " C_ENABLE\n"); - } - - if (usb_port_status.connected) { - port_status |= (1 << USB_PORT_FEAT_CONNECTION); - dev_dbg(dev, " CONNECTION\n"); - } - - if (usb_port_status.port_enabled) { - port_status |= (1 << USB_PORT_FEAT_ENABLE); - dev_dbg(dev, " ENABLE\n"); - } - - if (usb_port_status.port_over_current) { - port_status |= (1 << USB_PORT_FEAT_OVER_CURRENT); - dev_dbg(dev, " OVER_CURRENT\n"); - } - - if (usb_port_status.port_powered) { - port_status |= (1 << USB_PORT_FEAT_POWER); - dev_dbg(dev, " POWER\n"); - } - - if (usb_port_status.port_speed == CVMX_USB_SPEED_HIGH) { - port_status |= USB_PORT_STAT_HIGH_SPEED; - dev_dbg(dev, " HIGHSPEED\n"); - } else if (usb_port_status.port_speed == CVMX_USB_SPEED_LOW) { - port_status |= (1 << USB_PORT_FEAT_LOWSPEED); - dev_dbg(dev, " LOWSPEED\n"); - } - - *((__le32 *)buf) = cpu_to_le32(port_status); - break; - case SetHubFeature: - dev_dbg(dev, "SetHubFeature\n"); - /* No HUB features supported */ - break; - case SetPortFeature: - dev_dbg(dev, "SetPortFeature\n"); - if (wIndex != 1) { - dev_dbg(dev, " INVALID\n"); - return -EINVAL; - } - - switch (wValue) { - case USB_PORT_FEAT_SUSPEND: - dev_dbg(dev, " SUSPEND\n"); - return -EINVAL; - case USB_PORT_FEAT_POWER: - dev_dbg(dev, " POWER\n"); - /* - * Program the port power bit to drive VBUS on the USB. - */ - spin_lock_irqsave(&usb->lock, flags); - USB_SET_FIELD32(CVMX_USBCX_HPRT(usb->index), - cvmx_usbcx_hprt, prtpwr, 1); - spin_unlock_irqrestore(&usb->lock, flags); - return 0; - case USB_PORT_FEAT_RESET: - dev_dbg(dev, " RESET\n"); - spin_lock_irqsave(&usb->lock, flags); - cvmx_usb_reset_port(usb); - spin_unlock_irqrestore(&usb->lock, flags); - return 0; - case USB_PORT_FEAT_INDICATOR: - dev_dbg(dev, " INDICATOR\n"); - /* Not supported */ - break; - default: - dev_dbg(dev, " UNKNOWN\n"); - return -EINVAL; - } - break; - default: - dev_dbg(dev, "Unknown root hub request\n"); - return -EINVAL; - } - return 0; -} - -static const struct hc_driver octeon_hc_driver = { - .description = "Octeon USB", - .product_desc = "Octeon Host Controller", - .hcd_priv_size = sizeof(struct octeon_hcd), - .irq = octeon_usb_irq, - .flags = HCD_MEMORY | HCD_DMA | HCD_USB2, - .start = octeon_usb_start, - .stop = octeon_usb_stop, - .urb_enqueue = octeon_usb_urb_enqueue, - .urb_dequeue = octeon_usb_urb_dequeue, - .endpoint_disable = octeon_usb_endpoint_disable, - .get_frame_number = octeon_usb_get_frame_number, - .hub_status_data = octeon_usb_hub_status_data, - .hub_control = octeon_usb_hub_control, - .map_urb_for_dma = octeon_map_urb_for_dma, - .unmap_urb_for_dma = octeon_unmap_urb_for_dma, -}; - -static int octeon_usb_probe(struct platform_device *pdev) -{ - int status; - int initialize_flags; - int usb_num; - struct resource *res_mem; - struct device_node *usbn_node; - int irq = platform_get_irq(pdev, 0); - struct device *dev = &pdev->dev; - struct octeon_hcd *usb; - struct usb_hcd *hcd; - u32 clock_rate = 48000000; - bool is_crystal_clock = false; - const char *clock_type; - int i; - - if (!dev->of_node) { - dev_err(dev, "Error: empty of_node\n"); - return -ENXIO; - } - usbn_node = dev->of_node->parent; - - i = of_property_read_u32(usbn_node, - "clock-frequency", &clock_rate); - if (i) - i = of_property_read_u32(usbn_node, - "refclk-frequency", &clock_rate); - if (i) { - dev_err(dev, "No USBN \"clock-frequency\"\n"); - return -ENXIO; - } - switch (clock_rate) { - case 12000000: - initialize_flags = CVMX_USB_INITIALIZE_FLAGS_CLOCK_12MHZ; - break; - case 24000000: - initialize_flags = CVMX_USB_INITIALIZE_FLAGS_CLOCK_24MHZ; - break; - case 48000000: - initialize_flags = CVMX_USB_INITIALIZE_FLAGS_CLOCK_48MHZ; - break; - default: - dev_err(dev, "Illegal USBN \"clock-frequency\" %u\n", - clock_rate); - return -ENXIO; - } - - i = of_property_read_string(usbn_node, - "cavium,refclk-type", &clock_type); - if (i) - i = of_property_read_string(usbn_node, - "refclk-type", &clock_type); - - if (!i && strcmp("crystal", clock_type) == 0) - is_crystal_clock = true; - - if (is_crystal_clock) - initialize_flags |= CVMX_USB_INITIALIZE_FLAGS_CLOCK_XO_XI; - else - initialize_flags |= CVMX_USB_INITIALIZE_FLAGS_CLOCK_XO_GND; - - res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); - if (!res_mem) { - dev_err(dev, "found no memory resource\n"); - return -ENXIO; - } - usb_num = (res_mem->start >> 44) & 1; - - if (irq < 0) { - /* Defective device tree, but we know how to fix it. */ - irq_hw_number_t hwirq = usb_num ? (1 << 6) + 17 : 56; - - irq = irq_create_mapping(NULL, hwirq); - } - - /* - * Set the DMA mask to 64bits so we get buffers already translated for - * DMA. - */ - i = dma_coerce_mask_and_coherent(dev, DMA_BIT_MASK(64)); - if (i) - return i; - - /* - * Only cn52XX and cn56XX have DWC_OTG USB hardware and the - * IOB priority registers. Under heavy network load USB - * hardware can be starved by the IOB causing a crash. Give - * it a priority boost if it has been waiting more than 400 - * cycles to avoid this situation. - * - * Testing indicates that a cnt_val of 8192 is not sufficient, - * but no failures are seen with 4096. We choose a value of - * 400 to give a safety factor of 10. - */ - if (OCTEON_IS_MODEL(OCTEON_CN52XX) || OCTEON_IS_MODEL(OCTEON_CN56XX)) { - union cvmx_iob_n2c_l2c_pri_cnt pri_cnt; - - pri_cnt.u64 = 0; - pri_cnt.s.cnt_enb = 1; - pri_cnt.s.cnt_val = 400; - cvmx_write_csr(CVMX_IOB_N2C_L2C_PRI_CNT, pri_cnt.u64); - } - - hcd = usb_create_hcd(&octeon_hc_driver, dev, dev_name(dev)); - if (!hcd) { - dev_dbg(dev, "Failed to allocate memory for HCD\n"); - return -1; - } - hcd->uses_new_polling = 1; - usb = (struct octeon_hcd *)hcd->hcd_priv; - - spin_lock_init(&usb->lock); - - usb->init_flags = initialize_flags; - - /* Initialize the USB state structure */ - usb->index = usb_num; - INIT_LIST_HEAD(&usb->idle_pipes); - for (i = 0; i < ARRAY_SIZE(usb->active_pipes); i++) - INIT_LIST_HEAD(&usb->active_pipes[i]); - - /* Due to an errata, CN31XX doesn't support DMA */ - if (OCTEON_IS_MODEL(OCTEON_CN31XX)) { - usb->init_flags |= CVMX_USB_INITIALIZE_FLAGS_NO_DMA; - /* Only use one channel with non DMA */ - usb->idle_hardware_channels = 0x1; - } else if (OCTEON_IS_MODEL(OCTEON_CN5XXX)) { - /* CN5XXX have an errata with channel 3 */ - usb->idle_hardware_channels = 0xf7; - } else { - usb->idle_hardware_channels = 0xff; - } - - status = cvmx_usb_initialize(dev, usb); - if (status) { - dev_dbg(dev, "USB initialization failed with %d\n", status); - usb_put_hcd(hcd); - return -1; - } - - status = usb_add_hcd(hcd, irq, 0); - if (status) { - dev_dbg(dev, "USB add HCD failed with %d\n", status); - usb_put_hcd(hcd); - return -1; - } - device_wakeup_enable(hcd->self.controller); - - dev_info(dev, "Registered HCD for port %d on irq %d\n", usb_num, irq); - - return 0; -} - -static int octeon_usb_remove(struct platform_device *pdev) -{ - int status; - struct device *dev = &pdev->dev; - struct usb_hcd *hcd = dev_get_drvdata(dev); - struct octeon_hcd *usb = hcd_to_octeon(hcd); - unsigned long flags; - - usb_remove_hcd(hcd); - spin_lock_irqsave(&usb->lock, flags); - status = cvmx_usb_shutdown(usb); - spin_unlock_irqrestore(&usb->lock, flags); - if (status) - dev_dbg(dev, "USB shutdown failed with %d\n", status); - - usb_put_hcd(hcd); - - return 0; -} - -static const struct of_device_id octeon_usb_match[] = { - { - .compatible = "cavium,octeon-5750-usbc", - }, - {}, -}; -MODULE_DEVICE_TABLE(of, octeon_usb_match); - -static struct platform_driver octeon_usb_driver = { - .driver = { - .name = "octeon-hcd", - .of_match_table = octeon_usb_match, - }, - .probe = octeon_usb_probe, - .remove = octeon_usb_remove, -}; - -static int __init octeon_usb_driver_init(void) -{ - if (usb_disabled()) - return 0; - - return platform_driver_register(&octeon_usb_driver); -} -module_init(octeon_usb_driver_init); - -static void __exit octeon_usb_driver_exit(void) -{ - if (usb_disabled()) - return; - - platform_driver_unregister(&octeon_usb_driver); -} -module_exit(octeon_usb_driver_exit); - -MODULE_LICENSE("GPL"); -MODULE_AUTHOR("Cavium, Inc. <support@cavium.com>"); -MODULE_DESCRIPTION("Cavium Inc. OCTEON USB Host driver."); diff --git a/drivers/staging/octeon-usb/octeon-hcd.h b/drivers/staging/octeon-usb/octeon-hcd.h deleted file mode 100644 index 9ed619c93a4e..000000000000 --- a/drivers/staging/octeon-usb/octeon-hcd.h +++ /dev/null @@ -1,1847 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0 */ -/* - * Octeon HCD hardware register definitions. - * - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * - * Some parts of the code were originally released under BSD license: - * - * Copyright (c) 2003-2010 Cavium Networks (support@cavium.com). All rights - * reserved. - * - * Redistribution and use in source and binary forms, with or without - * modification, are permitted provided that the following conditions are - * met: - * - * * Redistributions of source code must retain the above copyright - * notice, this list of conditions and the following disclaimer. - * - * * Redistributions in binary form must reproduce the above - * copyright notice, this list of conditions and the following - * disclaimer in the documentation and/or other materials provided - * with the distribution. - * - * * Neither the name of Cavium Networks nor the names of - * its contributors may be used to endorse or promote products - * derived from this software without specific prior written - * permission. - * - * This Software, including technical data, may be subject to U.S. export - * control laws, including the U.S. Export Administration Act and its associated - * regulations, and may be subject to export or import regulations in other - * countries. - * - * TO THE MAXIMUM EXTENT PERMITTED BY LAW, THE SOFTWARE IS PROVIDED "AS IS" - * AND WITH ALL FAULTS AND CAVIUM NETWORKS MAKES NO PROMISES, REPRESENTATIONS OR - * WARRANTIES, EITHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, WITH RESPECT TO - * THE SOFTWARE, INCLUDING ITS CONDITION, ITS CONFORMITY TO ANY REPRESENTATION - * OR DESCRIPTION, OR THE EXISTENCE OF ANY LATENT OR PATENT DEFECTS, AND CAVIUM - * SPECIFICALLY DISCLAIMS ALL IMPLIED (IF ANY) WARRANTIES OF TITLE, - * MERCHANTABILITY, NONINFRINGEMENT, FITNESS FOR A PARTICULAR PURPOSE, LACK OF - * VIRUSES, ACCURACY OR COMPLETENESS, QUIET ENJOYMENT, QUIET POSSESSION OR - * CORRESPONDENCE TO DESCRIPTION. THE ENTIRE RISK ARISING OUT OF USE OR - * PERFORMANCE OF THE SOFTWARE LIES WITH YOU. - */ - -#ifndef __OCTEON_HCD_H__ -#define __OCTEON_HCD_H__ - -#include <asm/bitfield.h> - -#define CVMX_USBCXBASE 0x00016F0010000000ull -#define CVMX_USBCXREG1(reg, bid) \ - (CVMX_ADD_IO_SEG(CVMX_USBCXBASE | reg) + \ - ((bid) & 1) * 0x100000000000ull) -#define CVMX_USBCXREG2(reg, bid, off) \ - (CVMX_ADD_IO_SEG(CVMX_USBCXBASE | reg) + \ - (((off) & 7) + ((bid) & 1) * 0x8000000000ull) * 32) - -#define CVMX_USBCX_GAHBCFG(bid) CVMX_USBCXREG1(0x008, bid) -#define CVMX_USBCX_GHWCFG3(bid) CVMX_USBCXREG1(0x04c, bid) -#define CVMX_USBCX_GINTMSK(bid) CVMX_USBCXREG1(0x018, bid) -#define CVMX_USBCX_GINTSTS(bid) CVMX_USBCXREG1(0x014, bid) -#define CVMX_USBCX_GNPTXFSIZ(bid) CVMX_USBCXREG1(0x028, bid) -#define CVMX_USBCX_GNPTXSTS(bid) CVMX_USBCXREG1(0x02c, bid) -#define CVMX_USBCX_GOTGCTL(bid) CVMX_USBCXREG1(0x000, bid) -#define CVMX_USBCX_GRSTCTL(bid) CVMX_USBCXREG1(0x010, bid) -#define CVMX_USBCX_GRXFSIZ(bid) CVMX_USBCXREG1(0x024, bid) -#define CVMX_USBCX_GRXSTSPH(bid) CVMX_USBCXREG1(0x020, bid) -#define CVMX_USBCX_GUSBCFG(bid) CVMX_USBCXREG1(0x00c, bid) -#define CVMX_USBCX_HAINT(bid) CVMX_USBCXREG1(0x414, bid) -#define CVMX_USBCX_HAINTMSK(bid) CVMX_USBCXREG1(0x418, bid) -#define CVMX_USBCX_HCCHARX(off, bid) CVMX_USBCXREG2(0x500, bid, off) -#define CVMX_USBCX_HCFG(bid) CVMX_USBCXREG1(0x400, bid) -#define CVMX_USBCX_HCINTMSKX(off, bid) CVMX_USBCXREG2(0x50c, bid, off) -#define CVMX_USBCX_HCINTX(off, bid) CVMX_USBCXREG2(0x508, bid, off) -#define CVMX_USBCX_HCSPLTX(off, bid) CVMX_USBCXREG2(0x504, bid, off) -#define CVMX_USBCX_HCTSIZX(off, bid) CVMX_USBCXREG2(0x510, bid, off) -#define CVMX_USBCX_HFIR(bid) CVMX_USBCXREG1(0x404, bid) -#define CVMX_USBCX_HFNUM(bid) CVMX_USBCXREG1(0x408, bid) -#define CVMX_USBCX_HPRT(bid) CVMX_USBCXREG1(0x440, bid) -#define CVMX_USBCX_HPTXFSIZ(bid) CVMX_USBCXREG1(0x100, bid) -#define CVMX_USBCX_HPTXSTS(bid) CVMX_USBCXREG1(0x410, bid) - -#define CVMX_USBNXBID1(bid) (((bid) & 1) * 0x10000000ull) -#define CVMX_USBNXBID2(bid) (((bid) & 1) * 0x100000000000ull) - -#define CVMX_USBNXREG1(reg, bid) \ - (CVMX_ADD_IO_SEG(0x0001180068000000ull | reg) + CVMX_USBNXBID1(bid)) -#define CVMX_USBNXREG2(reg, bid) \ - (CVMX_ADD_IO_SEG(0x00016F0000000000ull | reg) + CVMX_USBNXBID2(bid)) - -#define CVMX_USBNX_CLK_CTL(bid) CVMX_USBNXREG1(0x10, bid) -#define CVMX_USBNX_DMA0_INB_CHN0(bid) CVMX_USBNXREG2(0x818, bid) -#define CVMX_USBNX_DMA0_OUTB_CHN0(bid) CVMX_USBNXREG2(0x858, bid) -#define CVMX_USBNX_USBP_CTL_STATUS(bid) CVMX_USBNXREG1(0x18, bid) - -/** - * cvmx_usbc#_gahbcfg - * - * Core AHB Configuration Register (GAHBCFG) - * - * This register can be used to configure the core after power-on or a change in - * mode of operation. This register mainly contains AHB system-related - * configuration parameters. The AHB is the processor interface to the O2P USB - * core. In general, software need not know about this interface except to - * program the values as specified. - * - * The application must program this register as part of the O2P USB core - * initialization. Do not change this register after the initial programming. - */ -union cvmx_usbcx_gahbcfg { - u32 u32; - /** - * struct cvmx_usbcx_gahbcfg_s - * @ptxfemplvl: Periodic TxFIFO Empty Level (PTxFEmpLvl) - * Software should set this bit to 0x1. - * Indicates when the Periodic TxFIFO Empty Interrupt bit in the - * Core Interrupt register (GINTSTS.PTxFEmp) is triggered. This - * bit is used only in Slave mode. - * * 1'b0: GINTSTS.PTxFEmp interrupt indicates that the Periodic - * TxFIFO is half empty - * * 1'b1: GINTSTS.PTxFEmp interrupt indicates that the Periodic - * TxFIFO is completely empty - * @nptxfemplvl: Non-Periodic TxFIFO Empty Level (NPTxFEmpLvl) - * Software should set this bit to 0x1. - * Indicates when the Non-Periodic TxFIFO Empty Interrupt bit in - * the Core Interrupt register (GINTSTS.NPTxFEmp) is triggered. - * This bit is used only in Slave mode. - * * 1'b0: GINTSTS.NPTxFEmp interrupt indicates that the Non- - * Periodic TxFIFO is half empty - * * 1'b1: GINTSTS.NPTxFEmp interrupt indicates that the Non- - * Periodic TxFIFO is completely empty - * @dmaen: DMA Enable (DMAEn) - * * 1'b0: Core operates in Slave mode - * * 1'b1: Core operates in a DMA mode - * @hbstlen: Burst Length/Type (HBstLen) - * This field has not effect and should be left as 0x0. - * @glblintrmsk: Global Interrupt Mask (GlblIntrMsk) - * Software should set this field to 0x1. - * The application uses this bit to mask or unmask the interrupt - * line assertion to itself. Irrespective of this bit's setting, - * the interrupt status registers are updated by the core. - * * 1'b0: Mask the interrupt assertion to the application. - * * 1'b1: Unmask the interrupt assertion to the application. - */ - struct cvmx_usbcx_gahbcfg_s { - __BITFIELD_FIELD(u32 reserved_9_31 : 23, - __BITFIELD_FIELD(u32 ptxfemplvl : 1, - __BITFIELD_FIELD(u32 nptxfemplvl : 1, - __BITFIELD_FIELD(u32 reserved_6_6 : 1, - __BITFIELD_FIELD(u32 dmaen : 1, - __BITFIELD_FIELD(u32 hbstlen : 4, - __BITFIELD_FIELD(u32 glblintrmsk : 1, - ;))))))) - } s; -}; - -/** - * cvmx_usbc#_ghwcfg3 - * - * User HW Config3 Register (GHWCFG3) - * - * This register contains the configuration options of the O2P USB core. - */ -union cvmx_usbcx_ghwcfg3 { - u32 u32; - /** - * struct cvmx_usbcx_ghwcfg3_s - * @dfifodepth: DFIFO Depth (DfifoDepth) - * This value is in terms of 32-bit words. - * * Minimum value is 32 - * * Maximum value is 32768 - * @ahbphysync: AHB and PHY Synchronous (AhbPhySync) - * Indicates whether AHB and PHY clocks are synchronous to - * each other. - * * 1'b0: No - * * 1'b1: Yes - * This bit is tied to 1. - * @rsttype: Reset Style for Clocked always Blocks in RTL (RstType) - * * 1'b0: Asynchronous reset is used in the core - * * 1'b1: Synchronous reset is used in the core - * @optfeature: Optional Features Removed (OptFeature) - * Indicates whether the User ID register, GPIO interface ports, - * and SOF toggle and counter ports were removed for gate count - * optimization. - * @vendor_control_interface_support: Vendor Control Interface Support - * * 1'b0: Vendor Control Interface is not available on the core. - * * 1'b1: Vendor Control Interface is available. - * @i2c_selection: I2C Selection - * * 1'b0: I2C Interface is not available on the core. - * * 1'b1: I2C Interface is available on the core. - * @otgen: OTG Function Enabled (OtgEn) - * The application uses this bit to indicate the O2P USB core's - * OTG capabilities. - * * 1'b0: Not OTG capable - * * 1'b1: OTG Capable - * @pktsizewidth: Width of Packet Size Counters (PktSizeWidth) - * * 3'b000: 4 bits - * * 3'b001: 5 bits - * * 3'b010: 6 bits - * * 3'b011: 7 bits - * * 3'b100: 8 bits - * * 3'b101: 9 bits - * * 3'b110: 10 bits - * * Others: Reserved - * @xfersizewidth: Width of Transfer Size Counters (XferSizeWidth) - * * 4'b0000: 11 bits - * * 4'b0001: 12 bits - * - ... - * * 4'b1000: 19 bits - * * Others: Reserved - */ - struct cvmx_usbcx_ghwcfg3_s { - __BITFIELD_FIELD(u32 dfifodepth : 16, - __BITFIELD_FIELD(u32 reserved_13_15 : 3, - __BITFIELD_FIELD(u32 ahbphysync : 1, - __BITFIELD_FIELD(u32 rsttype : 1, - __BITFIELD_FIELD(u32 optfeature : 1, - __BITFIELD_FIELD(u32 vendor_control_interface_support : 1, - __BITFIELD_FIELD(u32 i2c_selection : 1, - __BITFIELD_FIELD(u32 otgen : 1, - __BITFIELD_FIELD(u32 pktsizewidth : 3, - __BITFIELD_FIELD(u32 xfersizewidth : 4, - ;)))))))))) - } s; -}; - -/** - * cvmx_usbc#_gintmsk - * - * Core Interrupt Mask Register (GINTMSK) - * - * This register works with the Core Interrupt register to interrupt the - * application. When an interrupt bit is masked, the interrupt associated with - * that bit will not be generated. However, the Core Interrupt (GINTSTS) - * register bit corresponding to that interrupt will still be set. - * Mask interrupt: 1'b0, Unmask interrupt: 1'b1 - */ -union cvmx_usbcx_gintmsk { - u32 u32; - /** - * struct cvmx_usbcx_gintmsk_s - * @wkupintmsk: Resume/Remote Wakeup Detected Interrupt Mask - * (WkUpIntMsk) - * @sessreqintmsk: Session Request/New Session Detected Interrupt Mask - * (SessReqIntMsk) - * @disconnintmsk: Disconnect Detected Interrupt Mask (DisconnIntMsk) - * @conidstschngmsk: Connector ID Status Change Mask (ConIDStsChngMsk) - * @ptxfempmsk: Periodic TxFIFO Empty Mask (PTxFEmpMsk) - * @hchintmsk: Host Channels Interrupt Mask (HChIntMsk) - * @prtintmsk: Host Port Interrupt Mask (PrtIntMsk) - * @fetsuspmsk: Data Fetch Suspended Mask (FetSuspMsk) - * @incomplpmsk: Incomplete Periodic Transfer Mask (incomplPMsk) - * Incomplete Isochronous OUT Transfer Mask - * (incompISOOUTMsk) - * @incompisoinmsk: Incomplete Isochronous IN Transfer Mask - * (incompISOINMsk) - * @oepintmsk: OUT Endpoints Interrupt Mask (OEPIntMsk) - * @inepintmsk: IN Endpoints Interrupt Mask (INEPIntMsk) - * @epmismsk: Endpoint Mismatch Interrupt Mask (EPMisMsk) - * @eopfmsk: End of Periodic Frame Interrupt Mask (EOPFMsk) - * @isooutdropmsk: Isochronous OUT Packet Dropped Interrupt Mask - * (ISOOutDropMsk) - * @enumdonemsk: Enumeration Done Mask (EnumDoneMsk) - * @usbrstmsk: USB Reset Mask (USBRstMsk) - * @usbsuspmsk: USB Suspend Mask (USBSuspMsk) - * @erlysuspmsk: Early Suspend Mask (ErlySuspMsk) - * @i2cint: I2C Interrupt Mask (I2CINT) - * @ulpickintmsk: ULPI Carkit Interrupt Mask (ULPICKINTMsk) - * I2C Carkit Interrupt Mask (I2CCKINTMsk) - * @goutnakeffmsk: Global OUT NAK Effective Mask (GOUTNakEffMsk) - * @ginnakeffmsk: Global Non-Periodic IN NAK Effective Mask - * (GINNakEffMsk) - * @nptxfempmsk: Non-Periodic TxFIFO Empty Mask (NPTxFEmpMsk) - * @rxflvlmsk: Receive FIFO Non-Empty Mask (RxFLvlMsk) - * @sofmsk: Start of (micro)Frame Mask (SofMsk) - * @otgintmsk: OTG Interrupt Mask (OTGIntMsk) - * @modemismsk: Mode Mismatch Interrupt Mask (ModeMisMsk) - */ - struct cvmx_usbcx_gintmsk_s { - __BITFIELD_FIELD(u32 wkupintmsk : 1, - __BITFIELD_FIELD(u32 sessreqintmsk : 1, - __BITFIELD_FIELD(u32 disconnintmsk : 1, - __BITFIELD_FIELD(u32 conidstschngmsk : 1, - __BITFIELD_FIELD(u32 reserved_27_27 : 1, - __BITFIELD_FIELD(u32 ptxfempmsk : 1, - __BITFIELD_FIELD(u32 hchintmsk : 1, - __BITFIELD_FIELD(u32 prtintmsk : 1, - __BITFIELD_FIELD(u32 reserved_23_23 : 1, - __BITFIELD_FIELD(u32 fetsuspmsk : 1, - __BITFIELD_FIELD(u32 incomplpmsk : 1, - __BITFIELD_FIELD(u32 incompisoinmsk : 1, - __BITFIELD_FIELD(u32 oepintmsk : 1, - __BITFIELD_FIELD(u32 inepintmsk : 1, - __BITFIELD_FIELD(u32 epmismsk : 1, - __BITFIELD_FIELD(u32 reserved_16_16 : 1, - __BITFIELD_FIELD(u32 eopfmsk : 1, - __BITFIELD_FIELD(u32 isooutdropmsk : 1, - __BITFIELD_FIELD(u32 enumdonemsk : 1, - __BITFIELD_FIELD(u32 usbrstmsk : 1, - __BITFIELD_FIELD(u32 usbsuspmsk : 1, - __BITFIELD_FIELD(u32 erlysuspmsk : 1, - __BITFIELD_FIELD(u32 i2cint : 1, - __BITFIELD_FIELD(u32 ulpickintmsk : 1, - __BITFIELD_FIELD(u32 goutnakeffmsk : 1, - __BITFIELD_FIELD(u32 ginnakeffmsk : 1, - __BITFIELD_FIELD(u32 nptxfempmsk : 1, - __BITFIELD_FIELD(u32 rxflvlmsk : 1, - __BITFIELD_FIELD(u32 sofmsk : 1, - __BITFIELD_FIELD(u32 otgintmsk : 1, - __BITFIELD_FIELD(u32 modemismsk : 1, - __BITFIELD_FIELD(u32 reserved_0_0 : 1, - ;)))))))))))))))))))))))))))))))) - } s; -}; - -/** - * cvmx_usbc#_gintsts - * - * Core Interrupt Register (GINTSTS) - * - * This register interrupts the application for system-level events in the - * current mode of operation (Device mode or Host mode). It is shown in - * Interrupt. Some of the bits in this register are valid only in Host mode, - * while others are valid in Device mode only. This register also indicates the - * current mode of operation. In order to clear the interrupt status bits of - * type R_SS_WC, the application must write 1'b1 into the bit. The FIFO status - * interrupts are read only; once software reads from or writes to the FIFO - * while servicing these interrupts, FIFO interrupt conditions are cleared - * automatically. - */ -union cvmx_usbcx_gintsts { - u32 u32; - /** - * struct cvmx_usbcx_gintsts_s - * @wkupint: Resume/Remote Wakeup Detected Interrupt (WkUpInt) - * In Device mode, this interrupt is asserted when a resume is - * detected on the USB. In Host mode, this interrupt is asserted - * when a remote wakeup is detected on the USB. - * For more information on how to use this interrupt, see "Partial - * Power-Down and Clock Gating Programming Model" on - * page 353. - * @sessreqint: Session Request/New Session Detected Interrupt - * (SessReqInt) - * In Host mode, this interrupt is asserted when a session request - * is detected from the device. In Device mode, this interrupt is - * asserted when the utmiotg_bvalid signal goes high. - * For more information on how to use this interrupt, see "Partial - * Power-Down and Clock Gating Programming Model" on - * page 353. - * @disconnint: Disconnect Detected Interrupt (DisconnInt) - * Asserted when a device disconnect is detected. - * @conidstschng: Connector ID Status Change (ConIDStsChng) - * The core sets this bit when there is a change in connector ID - * status. - * @ptxfemp: Periodic TxFIFO Empty (PTxFEmp) - * Asserted when the Periodic Transmit FIFO is either half or - * completely empty and there is space for at least one entry to be - * written in the Periodic Request Queue. The half or completely - * empty status is determined by the Periodic TxFIFO Empty Level - * bit in the Core AHB Configuration register - * (GAHBCFG.PTxFEmpLvl). - * @hchint: Host Channels Interrupt (HChInt) - * The core sets this bit to indicate that an interrupt is pending - * on one of the channels of the core (in Host mode). The - * application must read the Host All Channels Interrupt (HAINT) - * register to determine the exact number of the channel on which - * the interrupt occurred, and then read the corresponding Host - * Channel-n Interrupt (HCINTn) register to determine the exact - * cause of the interrupt. The application must clear the - * appropriate status bit in the HCINTn register to clear this bit. - * @prtint: Host Port Interrupt (PrtInt) - * The core sets this bit to indicate a change in port status of - * one of the O2P USB core ports in Host mode. The application must - * read the Host Port Control and Status (HPRT) register to - * determine the exact event that caused this interrupt. The - * application must clear the appropriate status bit in the Host - * Port Control and Status register to clear this bit. - * @fetsusp: Data Fetch Suspended (FetSusp) - * This interrupt is valid only in DMA mode. This interrupt - * indicates that the core has stopped fetching data for IN - * endpoints due to the unavailability of TxFIFO space or Request - * Queue space. This interrupt is used by the application for an - * endpoint mismatch algorithm. - * @incomplp: Incomplete Periodic Transfer (incomplP) - * In Host mode, the core sets this interrupt bit when there are - * incomplete periodic transactions still pending which are - * scheduled for the current microframe. - * Incomplete Isochronous OUT Transfer (incompISOOUT) - * The Device mode, the core sets this interrupt to indicate that - * there is at least one isochronous OUT endpoint on which the - * transfer is not completed in the current microframe. This - * interrupt is asserted along with the End of Periodic Frame - * Interrupt (EOPF) bit in this register. - * @incompisoin: Incomplete Isochronous IN Transfer (incompISOIN) - * The core sets this interrupt to indicate that there is at least - * one isochronous IN endpoint on which the transfer is not - * completed in the current microframe. This interrupt is asserted - * along with the End of Periodic Frame Interrupt (EOPF) bit in - * this register. - * @oepint: OUT Endpoints Interrupt (OEPInt) - * The core sets this bit to indicate that an interrupt is pending - * on one of the OUT endpoints of the core (in Device mode). The - * application must read the Device All Endpoints Interrupt - * (DAINT) register to determine the exact number of the OUT - * endpoint on which the interrupt occurred, and then read the - * corresponding Device OUT Endpoint-n Interrupt (DOEPINTn) - * register to determine the exact cause of the interrupt. The - * application must clear the appropriate status bit in the - * corresponding DOEPINTn register to clear this bit. - * @iepint: IN Endpoints Interrupt (IEPInt) - * The core sets this bit to indicate that an interrupt is pending - * on one of the IN endpoints of the core (in Device mode). The - * application must read the Device All Endpoints Interrupt - * (DAINT) register to determine the exact number of the IN - * endpoint on which the interrupt occurred, and then read the - * corresponding Device IN Endpoint-n Interrupt (DIEPINTn) - * register to determine the exact cause of the interrupt. The - * application must clear the appropriate status bit in the - * corresponding DIEPINTn register to clear this bit. - * @epmis: Endpoint Mismatch Interrupt (EPMis) - * Indicates that an IN token has been received for a non-periodic - * endpoint, but the data for another endpoint is present in the - * top of the Non-Periodic Transmit FIFO and the IN endpoint - * mismatch count programmed by the application has expired. - * @eopf: End of Periodic Frame Interrupt (EOPF) - * Indicates that the period specified in the Periodic Frame - * Interval field of the Device Configuration register - * (DCFG.PerFrInt) has been reached in the current microframe. - * @isooutdrop: Isochronous OUT Packet Dropped Interrupt (ISOOutDrop) - * The core sets this bit when it fails to write an isochronous OUT - * packet into the RxFIFO because the RxFIFO doesn't have - * enough space to accommodate a maximum packet size packet - * for the isochronous OUT endpoint. - * @enumdone: Enumeration Done (EnumDone) - * The core sets this bit to indicate that speed enumeration is - * complete. The application must read the Device Status (DSTS) - * register to obtain the enumerated speed. - * @usbrst: USB Reset (USBRst) - * The core sets this bit to indicate that a reset is detected on - * the USB. - * @usbsusp: USB Suspend (USBSusp) - * The core sets this bit to indicate that a suspend was detected - * on the USB. The core enters the Suspended state when there - * is no activity on the phy_line_state_i signal for an extended - * period of time. - * @erlysusp: Early Suspend (ErlySusp) - * The core sets this bit to indicate that an Idle state has been - * detected on the USB for 3 ms. - * @i2cint: I2C Interrupt (I2CINT) - * This bit is always 0x0. - * @ulpickint: ULPI Carkit Interrupt (ULPICKINT) - * This bit is always 0x0. - * @goutnakeff: Global OUT NAK Effective (GOUTNakEff) - * Indicates that the Set Global OUT NAK bit in the Device Control - * register (DCTL.SGOUTNak), set by the application, has taken - * effect in the core. This bit can be cleared by writing the Clear - * Global OUT NAK bit in the Device Control register - * (DCTL.CGOUTNak). - * @ginnakeff: Global IN Non-Periodic NAK Effective (GINNakEff) - * Indicates that the Set Global Non-Periodic IN NAK bit in the - * Device Control register (DCTL.SGNPInNak), set by the - * application, has taken effect in the core. That is, the core has - * sampled the Global IN NAK bit set by the application. This bit - * can be cleared by clearing the Clear Global Non-Periodic IN - * NAK bit in the Device Control register (DCTL.CGNPInNak). - * This interrupt does not necessarily mean that a NAK handshake - * is sent out on the USB. The STALL bit takes precedence over - * the NAK bit. - * @nptxfemp: Non-Periodic TxFIFO Empty (NPTxFEmp) - * This interrupt is asserted when the Non-Periodic TxFIFO is - * either half or completely empty, and there is space for at least - * one entry to be written to the Non-Periodic Transmit Request - * Queue. The half or completely empty status is determined by - * the Non-Periodic TxFIFO Empty Level bit in the Core AHB - * Configuration register (GAHBCFG.NPTxFEmpLvl). - * @rxflvl: RxFIFO Non-Empty (RxFLvl) - * Indicates that there is at least one packet pending to be read - * from the RxFIFO. - * @sof: Start of (micro)Frame (Sof) - * In Host mode, the core sets this bit to indicate that an SOF - * (FS), micro-SOF (HS), or Keep-Alive (LS) is transmitted on the - * USB. The application must write a 1 to this bit to clear the - * interrupt. - * In Device mode, in the core sets this bit to indicate that an - * SOF token has been received on the USB. The application can read - * the Device Status register to get the current (micro)frame - * number. This interrupt is seen only when the core is operating - * at either HS or FS. - * @otgint: OTG Interrupt (OTGInt) - * The core sets this bit to indicate an OTG protocol event. The - * application must read the OTG Interrupt Status (GOTGINT) - * register to determine the exact event that caused this - * interrupt. The application must clear the appropriate status bit - * in the GOTGINT register to clear this bit. - * @modemis: Mode Mismatch Interrupt (ModeMis) - * The core sets this bit when the application is trying to access: - * * A Host mode register, when the core is operating in Device - * mode - * * A Device mode register, when the core is operating in Host - * mode - * The register access is completed on the AHB with an OKAY - * response, but is ignored by the core internally and doesn't - * affect the operation of the core. - * @curmod: Current Mode of Operation (CurMod) - * Indicates the current mode of operation. - * * 1'b0: Device mode - * * 1'b1: Host mode - */ - struct cvmx_usbcx_gintsts_s { - __BITFIELD_FIELD(u32 wkupint : 1, - __BITFIELD_FIELD(u32 sessreqint : 1, - __BITFIELD_FIELD(u32 disconnint : 1, - __BITFIELD_FIELD(u32 conidstschng : 1, - __BITFIELD_FIELD(u32 reserved_27_27 : 1, - __BITFIELD_FIELD(u32 ptxfemp : 1, - __BITFIELD_FIELD(u32 hchint : 1, - __BITFIELD_FIELD(u32 prtint : 1, - __BITFIELD_FIELD(u32 reserved_23_23 : 1, - __BITFIELD_FIELD(u32 fetsusp : 1, - __BITFIELD_FIELD(u32 incomplp : 1, - __BITFIELD_FIELD(u32 incompisoin : 1, - __BITFIELD_FIELD(u32 oepint : 1, - __BITFIELD_FIELD(u32 iepint : 1, - __BITFIELD_FIELD(u32 epmis : 1, - __BITFIELD_FIELD(u32 reserved_16_16 : 1, - __BITFIELD_FIELD(u32 eopf : 1, - __BITFIELD_FIELD(u32 isooutdrop : 1, - __BITFIELD_FIELD(u32 enumdone : 1, - __BITFIELD_FIELD(u32 usbrst : 1, - __BITFIELD_FIELD(u32 usbsusp : 1, - __BITFIELD_FIELD(u32 erlysusp : 1, - __BITFIELD_FIELD(u32 i2cint : 1, - __BITFIELD_FIELD(u32 ulpickint : 1, - __BITFIELD_FIELD(u32 goutnakeff : 1, - __BITFIELD_FIELD(u32 ginnakeff : 1, - __BITFIELD_FIELD(u32 nptxfemp : 1, - __BITFIELD_FIELD(u32 rxflvl : 1, - __BITFIELD_FIELD(u32 sof : 1, - __BITFIELD_FIELD(u32 otgint : 1, - __BITFIELD_FIELD(u32 modemis : 1, - __BITFIELD_FIELD(u32 curmod : 1, - ;)))))))))))))))))))))))))))))))) - } s; -}; - -/** - * cvmx_usbc#_gnptxfsiz - * - * Non-Periodic Transmit FIFO Size Register (GNPTXFSIZ) - * - * The application can program the RAM size and the memory start address for the - * Non-Periodic TxFIFO. - */ -union cvmx_usbcx_gnptxfsiz { - u32 u32; - /** - * struct cvmx_usbcx_gnptxfsiz_s - * @nptxfdep: Non-Periodic TxFIFO Depth (NPTxFDep) - * This value is in terms of 32-bit words. - * Minimum value is 16 - * Maximum value is 32768 - * @nptxfstaddr: Non-Periodic Transmit RAM Start Address (NPTxFStAddr) - * This field contains the memory start address for Non-Periodic - * Transmit FIFO RAM. - */ - struct cvmx_usbcx_gnptxfsiz_s { - __BITFIELD_FIELD(u32 nptxfdep : 16, - __BITFIELD_FIELD(u32 nptxfstaddr : 16, - ;)) - } s; -}; - -/** - * cvmx_usbc#_gnptxsts - * - * Non-Periodic Transmit FIFO/Queue Status Register (GNPTXSTS) - * - * This read-only register contains the free space information for the - * Non-Periodic TxFIFO and the Non-Periodic Transmit Request Queue. - */ -union cvmx_usbcx_gnptxsts { - u32 u32; - /** - * struct cvmx_usbcx_gnptxsts_s - * @nptxqtop: Top of the Non-Periodic Transmit Request Queue (NPTxQTop) - * Entry in the Non-Periodic Tx Request Queue that is currently - * being processed by the MAC. - * * Bits [30:27]: Channel/endpoint number - * * Bits [26:25]: - * - 2'b00: IN/OUT token - * - 2'b01: Zero-length transmit packet (device IN/host OUT) - * - 2'b10: PING/CSPLIT token - * - 2'b11: Channel halt command - * * Bit [24]: Terminate (last entry for selected channel/endpoint) - * @nptxqspcavail: Non-Periodic Transmit Request Queue Space Available - * (NPTxQSpcAvail) - * Indicates the amount of free space available in the Non- - * Periodic Transmit Request Queue. This queue holds both IN - * and OUT requests in Host mode. Device mode has only IN - * requests. - * * 8'h0: Non-Periodic Transmit Request Queue is full - * * 8'h1: 1 location available - * * 8'h2: 2 locations available - * * n: n locations available (0..8) - * * Others: Reserved - * @nptxfspcavail: Non-Periodic TxFIFO Space Avail (NPTxFSpcAvail) - * Indicates the amount of free space available in the Non- - * Periodic TxFIFO. - * Values are in terms of 32-bit words. - * * 16'h0: Non-Periodic TxFIFO is full - * * 16'h1: 1 word available - * * 16'h2: 2 words available - * * 16'hn: n words available (where 0..32768) - * * 16'h8000: 32768 words available - * * Others: Reserved - */ - struct cvmx_usbcx_gnptxsts_s { - __BITFIELD_FIELD(u32 reserved_31_31 : 1, - __BITFIELD_FIELD(u32 nptxqtop : 7, - __BITFIELD_FIELD(u32 nptxqspcavail : 8, - __BITFIELD_FIELD(u32 nptxfspcavail : 16, - ;)))) - } s; -}; - -/** - * cvmx_usbc#_grstctl - * - * Core Reset Register (GRSTCTL) - * - * The application uses this register to reset various hardware features inside - * the core. - */ -union cvmx_usbcx_grstctl { - u32 u32; - /** - * struct cvmx_usbcx_grstctl_s - * @ahbidle: AHB Master Idle (AHBIdle) - * Indicates that the AHB Master State Machine is in the IDLE - * condition. - * @dmareq: DMA Request Signal (DMAReq) - * Indicates that the DMA request is in progress. Used for debug. - * @txfnum: TxFIFO Number (TxFNum) - * This is the FIFO number that must be flushed using the TxFIFO - * Flush bit. This field must not be changed until the core clears - * the TxFIFO Flush bit. - * * 5'h0: Non-Periodic TxFIFO flush - * * 5'h1: Periodic TxFIFO 1 flush in Device mode or Periodic - * TxFIFO flush in Host mode - * * 5'h2: Periodic TxFIFO 2 flush in Device mode - * - ... - * * 5'hF: Periodic TxFIFO 15 flush in Device mode - * * 5'h10: Flush all the Periodic and Non-Periodic TxFIFOs in the - * core - * @txfflsh: TxFIFO Flush (TxFFlsh) - * This bit selectively flushes a single or all transmit FIFOs, but - * cannot do so if the core is in the midst of a transaction. - * The application must only write this bit after checking that the - * core is neither writing to the TxFIFO nor reading from the - * TxFIFO. - * The application must wait until the core clears this bit before - * performing any operations. This bit takes 8 clocks (of phy_clk - * or hclk, whichever is slower) to clear. - * @rxfflsh: RxFIFO Flush (RxFFlsh) - * The application can flush the entire RxFIFO using this bit, but - * must first ensure that the core is not in the middle of a - * transaction. - * The application must only write to this bit after checking that - * the core is neither reading from the RxFIFO nor writing to the - * RxFIFO. - * The application must wait until the bit is cleared before - * performing any other operations. This bit will take 8 clocks - * (slowest of PHY or AHB clock) to clear. - * @intknqflsh: IN Token Sequence Learning Queue Flush (INTknQFlsh) - * The application writes this bit to flush the IN Token Sequence - * Learning Queue. - * @frmcntrrst: Host Frame Counter Reset (FrmCntrRst) - * The application writes this bit to reset the (micro)frame number - * counter inside the core. When the (micro)frame counter is reset, - * the subsequent SOF sent out by the core will have a - * (micro)frame number of 0. - * @hsftrst: HClk Soft Reset (HSftRst) - * The application uses this bit to flush the control logic in the - * AHB Clock domain. Only AHB Clock Domain pipelines are reset. - * * FIFOs are not flushed with this bit. - * * All state machines in the AHB clock domain are reset to the - * Idle state after terminating the transactions on the AHB, - * following the protocol. - * * CSR control bits used by the AHB clock domain state - * machines are cleared. - * * To clear this interrupt, status mask bits that control the - * interrupt status and are generated by the AHB clock domain - * state machine are cleared. - * * Because interrupt status bits are not cleared, the application - * can get the status of any core events that occurred after it set - * this bit. - * This is a self-clearing bit that the core clears after all - * necessary logic is reset in the core. This may take several - * clocks, depending on the core's current state. - * @csftrst: Core Soft Reset (CSftRst) - * Resets the hclk and phy_clock domains as follows: - * * Clears the interrupts and all the CSR registers except the - * following register bits: - * - PCGCCTL.RstPdwnModule - * - PCGCCTL.GateHclk - * - PCGCCTL.PwrClmp - * - PCGCCTL.StopPPhyLPwrClkSelclk - * - GUSBCFG.PhyLPwrClkSel - * - GUSBCFG.DDRSel - * - GUSBCFG.PHYSel - * - GUSBCFG.FSIntf - * - GUSBCFG.ULPI_UTMI_Sel - * - GUSBCFG.PHYIf - * - HCFG.FSLSPclkSel - * - DCFG.DevSpd - * * All module state machines (except the AHB Slave Unit) are - * reset to the IDLE state, and all the transmit FIFOs and the - * receive FIFO are flushed. - * * Any transactions on the AHB Master are terminated as soon - * as possible, after gracefully completing the last data phase of - * an AHB transfer. Any transactions on the USB are terminated - * immediately. - * The application can write to this bit any time it wants to reset - * the core. This is a self-clearing bit and the core clears this - * bit after all the necessary logic is reset in the core, which - * may take several clocks, depending on the current state of the - * core. Once this bit is cleared software should wait at least 3 - * PHY clocks before doing any access to the PHY domain - * (synchronization delay). Software should also should check that - * bit 31 of this register is 1 (AHB Master is IDLE) before - * starting any operation. - * Typically software reset is used during software development - * and also when you dynamically change the PHY selection bits - * in the USB configuration registers listed above. When you - * change the PHY, the corresponding clock for the PHY is - * selected and used in the PHY domain. Once a new clock is - * selected, the PHY domain has to be reset for proper operation. - */ - struct cvmx_usbcx_grstctl_s { - __BITFIELD_FIELD(u32 ahbidle : 1, - __BITFIELD_FIELD(u32 dmareq : 1, - __BITFIELD_FIELD(u32 reserved_11_29 : 19, - __BITFIELD_FIELD(u32 txfnum : 5, - __BITFIELD_FIELD(u32 txfflsh : 1, - __BITFIELD_FIELD(u32 rxfflsh : 1, - __BITFIELD_FIELD(u32 intknqflsh : 1, - __BITFIELD_FIELD(u32 frmcntrrst : 1, - __BITFIELD_FIELD(u32 hsftrst : 1, - __BITFIELD_FIELD(u32 csftrst : 1, - ;)))))))))) - } s; -}; - -/** - * cvmx_usbc#_grxfsiz - * - * Receive FIFO Size Register (GRXFSIZ) - * - * The application can program the RAM size that must be allocated to the - * RxFIFO. - */ -union cvmx_usbcx_grxfsiz { - u32 u32; - /** - * struct cvmx_usbcx_grxfsiz_s - * @rxfdep: RxFIFO Depth (RxFDep) - * This value is in terms of 32-bit words. - * * Minimum value is 16 - * * Maximum value is 32768 - */ - struct cvmx_usbcx_grxfsiz_s { - __BITFIELD_FIELD(u32 reserved_16_31 : 16, - __BITFIELD_FIELD(u32 rxfdep : 16, - ;)) - } s; -}; - -/** - * cvmx_usbc#_grxstsph - * - * Receive Status Read and Pop Register, Host Mode (GRXSTSPH) - * - * A read to the Receive Status Read and Pop register returns and additionally - * pops the top data entry out of the RxFIFO. - * This Description is only valid when the core is in Host Mode. For Device Mode - * use USBC_GRXSTSPD instead. - * NOTE: GRXSTSPH and GRXSTSPD are physically the same register and share the - * same offset in the O2P USB core. The offset difference shown in this - * document is for software clarity and is actually ignored by the - * hardware. - */ -union cvmx_usbcx_grxstsph { - u32 u32; - /** - * struct cvmx_usbcx_grxstsph_s - * @pktsts: Packet Status (PktSts) - * Indicates the status of the received packet - * * 4'b0010: IN data packet received - * * 4'b0011: IN transfer completed (triggers an interrupt) - * * 4'b0101: Data toggle error (triggers an interrupt) - * * 4'b0111: Channel halted (triggers an interrupt) - * * Others: Reserved - * @dpid: Data PID (DPID) - * * 2'b00: DATA0 - * * 2'b10: DATA1 - * * 2'b01: DATA2 - * * 2'b11: MDATA - * @bcnt: Byte Count (BCnt) - * Indicates the byte count of the received IN data packet - * @chnum: Channel Number (ChNum) - * Indicates the channel number to which the current received - * packet belongs. - */ - struct cvmx_usbcx_grxstsph_s { - __BITFIELD_FIELD(u32 reserved_21_31 : 11, - __BITFIELD_FIELD(u32 pktsts : 4, - __BITFIELD_FIELD(u32 dpid : 2, - __BITFIELD_FIELD(u32 bcnt : 11, - __BITFIELD_FIELD(u32 chnum : 4, - ;))))) - } s; -}; - -/** - * cvmx_usbc#_gusbcfg - * - * Core USB Configuration Register (GUSBCFG) - * - * This register can be used to configure the core after power-on or a changing - * to Host mode or Device mode. It contains USB and USB-PHY related - * configuration parameters. The application must program this register before - * starting any transactions on either the AHB or the USB. Do not make changes - * to this register after the initial programming. - */ -union cvmx_usbcx_gusbcfg { - u32 u32; - /** - * struct cvmx_usbcx_gusbcfg_s - * @otgi2csel: UTMIFS or I2C Interface Select (OtgI2CSel) - * This bit is always 0x0. - * @phylpwrclksel: PHY Low-Power Clock Select (PhyLPwrClkSel) - * Software should set this bit to 0x0. - * Selects either 480-MHz or 48-MHz (low-power) PHY mode. In - * FS and LS modes, the PHY can usually operate on a 48-MHz - * clock to save power. - * * 1'b0: 480-MHz Internal PLL clock - * * 1'b1: 48-MHz External Clock - * In 480 MHz mode, the UTMI interface operates at either 60 or - * 30-MHz, depending upon whether 8- or 16-bit data width is - * selected. In 48-MHz mode, the UTMI interface operates at 48 - * MHz in FS mode and at either 48 or 6 MHz in LS mode - * (depending on the PHY vendor). - * This bit drives the utmi_fsls_low_power core output signal, and - * is valid only for UTMI+ PHYs. - * @usbtrdtim: USB Turnaround Time (USBTrdTim) - * Sets the turnaround time in PHY clocks. - * Specifies the response time for a MAC request to the Packet - * FIFO Controller (PFC) to fetch data from the DFIFO (SPRAM). - * This must be programmed to 0x5. - * @hnpcap: HNP-Capable (HNPCap) - * This bit is always 0x0. - * @srpcap: SRP-Capable (SRPCap) - * This bit is always 0x0. - * @ddrsel: ULPI DDR Select (DDRSel) - * Software should set this bit to 0x0. - * @physel: USB 2.0 High-Speed PHY or USB 1.1 Full-Speed Serial - * Software should set this bit to 0x0. - * @fsintf: Full-Speed Serial Interface Select (FSIntf) - * Software should set this bit to 0x0. - * @ulpi_utmi_sel: ULPI or UTMI+ Select (ULPI_UTMI_Sel) - * This bit is always 0x0. - * @phyif: PHY Interface (PHYIf) - * This bit is always 0x1. - * @toutcal: HS/FS Timeout Calibration (TOutCal) - * The number of PHY clocks that the application programs in this - * field is added to the high-speed/full-speed interpacket timeout - * duration in the core to account for any additional delays - * introduced by the PHY. This may be required, since the delay - * introduced by the PHY in generating the linestate condition may - * vary from one PHY to another. - * The USB standard timeout value for high-speed operation is - * 736 to 816 (inclusive) bit times. The USB standard timeout - * value for full-speed operation is 16 to 18 (inclusive) bit - * times. The application must program this field based on the - * speed of enumeration. The number of bit times added per PHY - * clock are: - * High-speed operation: - * * One 30-MHz PHY clock = 16 bit times - * * One 60-MHz PHY clock = 8 bit times - * Full-speed operation: - * * One 30-MHz PHY clock = 0.4 bit times - * * One 60-MHz PHY clock = 0.2 bit times - * * One 48-MHz PHY clock = 0.25 bit times - */ - struct cvmx_usbcx_gusbcfg_s { - __BITFIELD_FIELD(u32 reserved_17_31 : 15, - __BITFIELD_FIELD(u32 otgi2csel : 1, - __BITFIELD_FIELD(u32 phylpwrclksel : 1, - __BITFIELD_FIELD(u32 reserved_14_14 : 1, - __BITFIELD_FIELD(u32 usbtrdtim : 4, - __BITFIELD_FIELD(u32 hnpcap : 1, - __BITFIELD_FIELD(u32 srpcap : 1, - __BITFIELD_FIELD(u32 ddrsel : 1, - __BITFIELD_FIELD(u32 physel : 1, - __BITFIELD_FIELD(u32 fsintf : 1, - __BITFIELD_FIELD(u32 ulpi_utmi_sel : 1, - __BITFIELD_FIELD(u32 phyif : 1, - __BITFIELD_FIELD(u32 toutcal : 3, - ;))))))))))))) - } s; -}; - -/** - * cvmx_usbc#_haint - * - * Host All Channels Interrupt Register (HAINT) - * - * When a significant event occurs on a channel, the Host All Channels Interrupt - * register interrupts the application using the Host Channels Interrupt bit of - * the Core Interrupt register (GINTSTS.HChInt). This is shown in Interrupt. - * There is one interrupt bit per channel, up to a maximum of 16 bits. Bits in - * this register are set and cleared when the application sets and clears bits - * in the corresponding Host Channel-n Interrupt register. - */ -union cvmx_usbcx_haint { - u32 u32; - /** - * struct cvmx_usbcx_haint_s - * @haint: Channel Interrupts (HAINT) - * One bit per channel: Bit 0 for Channel 0, bit 15 for Channel 15 - */ - struct cvmx_usbcx_haint_s { - __BITFIELD_FIELD(u32 reserved_16_31 : 16, - __BITFIELD_FIELD(u32 haint : 16, - ;)) - } s; -}; - -/** - * cvmx_usbc#_haintmsk - * - * Host All Channels Interrupt Mask Register (HAINTMSK) - * - * The Host All Channel Interrupt Mask register works with the Host All Channel - * Interrupt register to interrupt the application when an event occurs on a - * channel. There is one interrupt mask bit per channel, up to a maximum of 16 - * bits. - * Mask interrupt: 1'b0 Unmask interrupt: 1'b1 - */ -union cvmx_usbcx_haintmsk { - u32 u32; - /** - * struct cvmx_usbcx_haintmsk_s - * @haintmsk: Channel Interrupt Mask (HAINTMsk) - * One bit per channel: Bit 0 for channel 0, bit 15 for channel 15 - */ - struct cvmx_usbcx_haintmsk_s { - __BITFIELD_FIELD(u32 reserved_16_31 : 16, - __BITFIELD_FIELD(u32 haintmsk : 16, - ;)) - } s; -}; - -/** - * cvmx_usbc#_hcchar# - * - * Host Channel-n Characteristics Register (HCCHAR) - * - */ -union cvmx_usbcx_hccharx { - u32 u32; - /** - * struct cvmx_usbcx_hccharx_s - * @chena: Channel Enable (ChEna) - * This field is set by the application and cleared by the OTG - * host. - * * 1'b0: Channel disabled - * * 1'b1: Channel enabled - * @chdis: Channel Disable (ChDis) - * The application sets this bit to stop transmitting/receiving - * data on a channel, even before the transfer for that channel is - * complete. The application must wait for the Channel Disabled - * interrupt before treating the channel as disabled. - * @oddfrm: Odd Frame (OddFrm) - * This field is set (reset) by the application to indicate that - * the OTG host must perform a transfer in an odd (micro)frame. - * This field is applicable for only periodic (isochronous and - * interrupt) transactions. - * * 1'b0: Even (micro)frame - * * 1'b1: Odd (micro)frame - * @devaddr: Device Address (DevAddr) - * This field selects the specific device serving as the data - * source or sink. - * @ec: Multi Count (MC) / Error Count (EC) - * When the Split Enable bit of the Host Channel-n Split Control - * register (HCSPLTn.SpltEna) is reset (1'b0), this field indicates - * to the host the number of transactions that should be executed - * per microframe for this endpoint. - * * 2'b00: Reserved. This field yields undefined results. - * * 2'b01: 1 transaction - * * 2'b10: 2 transactions to be issued for this endpoint per - * microframe - * * 2'b11: 3 transactions to be issued for this endpoint per - * microframe - * When HCSPLTn.SpltEna is set (1'b1), this field indicates the - * number of immediate retries to be performed for a periodic split - * transactions on transaction errors. This field must be set to at - * least 2'b01. - * @eptype: Endpoint Type (EPType) - * Indicates the transfer type selected. - * * 2'b00: Control - * * 2'b01: Isochronous - * * 2'b10: Bulk - * * 2'b11: Interrupt - * @lspddev: Low-Speed Device (LSpdDev) - * This field is set by the application to indicate that this - * channel is communicating to a low-speed device. - * @epdir: Endpoint Direction (EPDir) - * Indicates whether the transaction is IN or OUT. - * * 1'b0: OUT - * * 1'b1: IN - * @epnum: Endpoint Number (EPNum) - * Indicates the endpoint number on the device serving as the - * data source or sink. - * @mps: Maximum Packet Size (MPS) - * Indicates the maximum packet size of the associated endpoint. - */ - struct cvmx_usbcx_hccharx_s { - __BITFIELD_FIELD(u32 chena : 1, - __BITFIELD_FIELD(u32 chdis : 1, - __BITFIELD_FIELD(u32 oddfrm : 1, - __BITFIELD_FIELD(u32 devaddr : 7, - __BITFIELD_FIELD(u32 ec : 2, - __BITFIELD_FIELD(u32 eptype : 2, - __BITFIELD_FIELD(u32 lspddev : 1, - __BITFIELD_FIELD(u32 reserved_16_16 : 1, - __BITFIELD_FIELD(u32 epdir : 1, - __BITFIELD_FIELD(u32 epnum : 4, - __BITFIELD_FIELD(u32 mps : 11, - ;))))))))))) - } s; -}; - -/** - * cvmx_usbc#_hcfg - * - * Host Configuration Register (HCFG) - * - * This register configures the core after power-on. Do not make changes to this - * register after initializing the host. - */ -union cvmx_usbcx_hcfg { - u32 u32; - /** - * struct cvmx_usbcx_hcfg_s - * @fslssupp: FS- and LS-Only Support (FSLSSupp) - * The application uses this bit to control the core's enumeration - * speed. Using this bit, the application can make the core - * enumerate as a FS host, even if the connected device supports - * HS traffic. Do not make changes to this field after initial - * programming. - * * 1'b0: HS/FS/LS, based on the maximum speed supported by - * the connected device - * * 1'b1: FS/LS-only, even if the connected device can support HS - * @fslspclksel: FS/LS PHY Clock Select (FSLSPclkSel) - * When the core is in FS Host mode - * * 2'b00: PHY clock is running at 30/60 MHz - * * 2'b01: PHY clock is running at 48 MHz - * * Others: Reserved - * When the core is in LS Host mode - * * 2'b00: PHY clock is running at 30/60 MHz. When the - * UTMI+/ULPI PHY Low Power mode is not selected, use - * 30/60 MHz. - * * 2'b01: PHY clock is running at 48 MHz. When the UTMI+ - * PHY Low Power mode is selected, use 48MHz if the PHY - * supplies a 48 MHz clock during LS mode. - * * 2'b10: PHY clock is running at 6 MHz. In USB 1.1 FS mode, - * use 6 MHz when the UTMI+ PHY Low Power mode is - * selected and the PHY supplies a 6 MHz clock during LS - * mode. If you select a 6 MHz clock during LS mode, you must - * do a soft reset. - * * 2'b11: Reserved - */ - struct cvmx_usbcx_hcfg_s { - __BITFIELD_FIELD(u32 reserved_3_31 : 29, - __BITFIELD_FIELD(u32 fslssupp : 1, - __BITFIELD_FIELD(u32 fslspclksel : 2, - ;))) - } s; -}; - -/** - * cvmx_usbc#_hcint# - * - * Host Channel-n Interrupt Register (HCINT) - * - * This register indicates the status of a channel with respect to USB- and - * AHB-related events. The application must read this register when the Host - * Channels Interrupt bit of the Core Interrupt register (GINTSTS.HChInt) is - * set. Before the application can read this register, it must first read - * the Host All Channels Interrupt (HAINT) register to get the exact channel - * number for the Host Channel-n Interrupt register. The application must clear - * the appropriate bit in this register to clear the corresponding bits in the - * HAINT and GINTSTS registers. - */ -union cvmx_usbcx_hcintx { - u32 u32; - /** - * struct cvmx_usbcx_hcintx_s - * @datatglerr: Data Toggle Error (DataTglErr) - * @frmovrun: Frame Overrun (FrmOvrun) - * @bblerr: Babble Error (BblErr) - * @xacterr: Transaction Error (XactErr) - * @nyet: NYET Response Received Interrupt (NYET) - * @ack: ACK Response Received Interrupt (ACK) - * @nak: NAK Response Received Interrupt (NAK) - * @stall: STALL Response Received Interrupt (STALL) - * @ahberr: This bit is always 0x0. - * @chhltd: Channel Halted (ChHltd) - * Indicates the transfer completed abnormally either because of - * any USB transaction error or in response to disable request by - * the application. - * @xfercompl: Transfer Completed (XferCompl) - * Transfer completed normally without any errors. - */ - struct cvmx_usbcx_hcintx_s { - __BITFIELD_FIELD(u32 reserved_11_31 : 21, - __BITFIELD_FIELD(u32 datatglerr : 1, - __BITFIELD_FIELD(u32 frmovrun : 1, - __BITFIELD_FIELD(u32 bblerr : 1, - __BITFIELD_FIELD(u32 xacterr : 1, - __BITFIELD_FIELD(u32 nyet : 1, - __BITFIELD_FIELD(u32 ack : 1, - __BITFIELD_FIELD(u32 nak : 1, - __BITFIELD_FIELD(u32 stall : 1, - __BITFIELD_FIELD(u32 ahberr : 1, - __BITFIELD_FIELD(u32 chhltd : 1, - __BITFIELD_FIELD(u32 xfercompl : 1, - ;)))))))))))) - } s; -}; - -/** - * cvmx_usbc#_hcintmsk# - * - * Host Channel-n Interrupt Mask Register (HCINTMSKn) - * - * This register reflects the mask for each channel status described in the - * previous section. - * Mask interrupt: 1'b0 Unmask interrupt: 1'b1 - */ -union cvmx_usbcx_hcintmskx { - u32 u32; - /** - * struct cvmx_usbcx_hcintmskx_s - * @datatglerrmsk: Data Toggle Error Mask (DataTglErrMsk) - * @frmovrunmsk: Frame Overrun Mask (FrmOvrunMsk) - * @bblerrmsk: Babble Error Mask (BblErrMsk) - * @xacterrmsk: Transaction Error Mask (XactErrMsk) - * @nyetmsk: NYET Response Received Interrupt Mask (NyetMsk) - * @ackmsk: ACK Response Received Interrupt Mask (AckMsk) - * @nakmsk: NAK Response Received Interrupt Mask (NakMsk) - * @stallmsk: STALL Response Received Interrupt Mask (StallMsk) - * @ahberrmsk: AHB Error Mask (AHBErrMsk) - * @chhltdmsk: Channel Halted Mask (ChHltdMsk) - * @xfercomplmsk: Transfer Completed Mask (XferComplMsk) - */ - struct cvmx_usbcx_hcintmskx_s { - __BITFIELD_FIELD(u32 reserved_11_31 : 21, - __BITFIELD_FIELD(u32 datatglerrmsk : 1, - __BITFIELD_FIELD(u32 frmovrunmsk : 1, - __BITFIELD_FIELD(u32 bblerrmsk : 1, - __BITFIELD_FIELD(u32 xacterrmsk : 1, - __BITFIELD_FIELD(u32 nyetmsk : 1, - __BITFIELD_FIELD(u32 ackmsk : 1, - __BITFIELD_FIELD(u32 nakmsk : 1, - __BITFIELD_FIELD(u32 stallmsk : 1, - __BITFIELD_FIELD(u32 ahberrmsk : 1, - __BITFIELD_FIELD(u32 chhltdmsk : 1, - __BITFIELD_FIELD(u32 xfercomplmsk : 1, - ;)))))))))))) - } s; -}; - -/** - * cvmx_usbc#_hcsplt# - * - * Host Channel-n Split Control Register (HCSPLT) - * - */ -union cvmx_usbcx_hcspltx { - u32 u32; - /** - * struct cvmx_usbcx_hcspltx_s - * @spltena: Split Enable (SpltEna) - * The application sets this field to indicate that this channel is - * enabled to perform split transactions. - * @compsplt: Do Complete Split (CompSplt) - * The application sets this field to request the OTG host to - * perform a complete split transaction. - * @xactpos: Transaction Position (XactPos) - * This field is used to determine whether to send all, first, - * middle, or last payloads with each OUT transaction. - * * 2'b11: All. This is the entire data payload is of this - * transaction (which is less than or equal to 188 bytes). - * * 2'b10: Begin. This is the first data payload of this - * transaction (which is larger than 188 bytes). - * * 2'b00: Mid. This is the middle payload of this transaction - * (which is larger than 188 bytes). - * * 2'b01: End. This is the last payload of this transaction - * (which is larger than 188 bytes). - * @hubaddr: Hub Address (HubAddr) - * This field holds the device address of the transaction - * translator's hub. - * @prtaddr: Port Address (PrtAddr) - * This field is the port number of the recipient transaction - * translator. - */ - struct cvmx_usbcx_hcspltx_s { - __BITFIELD_FIELD(u32 spltena : 1, - __BITFIELD_FIELD(u32 reserved_17_30 : 14, - __BITFIELD_FIELD(u32 compsplt : 1, - __BITFIELD_FIELD(u32 xactpos : 2, - __BITFIELD_FIELD(u32 hubaddr : 7, - __BITFIELD_FIELD(u32 prtaddr : 7, - ;)))))) - } s; -}; - -/** - * cvmx_usbc#_hctsiz# - * - * Host Channel-n Transfer Size Register (HCTSIZ) - * - */ -union cvmx_usbcx_hctsizx { - u32 u32; - /** - * struct cvmx_usbcx_hctsizx_s - * @dopng: Do Ping (DoPng) - * Setting this field to 1 directs the host to do PING protocol. - * @pid: PID (Pid) - * The application programs this field with the type of PID to use - * for the initial transaction. The host will maintain this field - * for the rest of the transfer. - * * 2'b00: DATA0 - * * 2'b01: DATA2 - * * 2'b10: DATA1 - * * 2'b11: MDATA (non-control)/SETUP (control) - * @pktcnt: Packet Count (PktCnt) - * This field is programmed by the application with the expected - * number of packets to be transmitted (OUT) or received (IN). - * The host decrements this count on every successful - * transmission or reception of an OUT/IN packet. Once this count - * reaches zero, the application is interrupted to indicate normal - * completion. - * @xfersize: Transfer Size (XferSize) - * For an OUT, this field is the number of data bytes the host will - * send during the transfer. - * For an IN, this field is the buffer size that the application - * has reserved for the transfer. The application is expected to - * program this field as an integer multiple of the maximum packet - * size for IN transactions (periodic and non-periodic). - */ - struct cvmx_usbcx_hctsizx_s { - __BITFIELD_FIELD(u32 dopng : 1, - __BITFIELD_FIELD(u32 pid : 2, - __BITFIELD_FIELD(u32 pktcnt : 10, - __BITFIELD_FIELD(u32 xfersize : 19, - ;)))) - } s; -}; - -/** - * cvmx_usbc#_hfir - * - * Host Frame Interval Register (HFIR) - * - * This register stores the frame interval information for the current speed to - * which the O2P USB core has enumerated. - */ -union cvmx_usbcx_hfir { - u32 u32; - /** - * struct cvmx_usbcx_hfir_s - * @frint: Frame Interval (FrInt) - * The value that the application programs to this field specifies - * the interval between two consecutive SOFs (FS) or micro- - * SOFs (HS) or Keep-Alive tokens (HS). This field contains the - * number of PHY clocks that constitute the required frame - * interval. The default value set in this field for a FS operation - * when the PHY clock frequency is 60 MHz. The application can - * write a value to this register only after the Port Enable bit of - * the Host Port Control and Status register (HPRT.PrtEnaPort) - * has been set. If no value is programmed, the core calculates - * the value based on the PHY clock specified in the FS/LS PHY - * Clock Select field of the Host Configuration register - * (HCFG.FSLSPclkSel). Do not change the value of this field - * after the initial configuration. - * * 125 us (PHY clock frequency for HS) - * * 1 ms (PHY clock frequency for FS/LS) - */ - struct cvmx_usbcx_hfir_s { - __BITFIELD_FIELD(u32 reserved_16_31 : 16, - __BITFIELD_FIELD(u32 frint : 16, - ;)) - } s; -}; - -/** - * cvmx_usbc#_hfnum - * - * Host Frame Number/Frame Time Remaining Register (HFNUM) - * - * This register indicates the current frame number. - * It also indicates the time remaining (in terms of the number of PHY clocks) - * in the current (micro)frame. - */ -union cvmx_usbcx_hfnum { - u32 u32; - /** - * struct cvmx_usbcx_hfnum_s - * @frrem: Frame Time Remaining (FrRem) - * Indicates the amount of time remaining in the current - * microframe (HS) or frame (FS/LS), in terms of PHY clocks. - * This field decrements on each PHY clock. When it reaches - * zero, this field is reloaded with the value in the Frame - * Interval register and a new SOF is transmitted on the USB. - * @frnum: Frame Number (FrNum) - * This field increments when a new SOF is transmitted on the - * USB, and is reset to 0 when it reaches 16'h3FFF. - */ - struct cvmx_usbcx_hfnum_s { - __BITFIELD_FIELD(u32 frrem : 16, - __BITFIELD_FIELD(u32 frnum : 16, - ;)) - } s; -}; - -/** - * cvmx_usbc#_hprt - * - * Host Port Control and Status Register (HPRT) - * - * This register is available in both Host and Device modes. - * Currently, the OTG Host supports only one port. - * A single register holds USB port-related information such as USB reset, - * enable, suspend, resume, connect status, and test mode for each port. The - * R_SS_WC bits in this register can trigger an interrupt to the application - * through the Host Port Interrupt bit of the Core Interrupt register - * (GINTSTS.PrtInt). On a Port Interrupt, the application must read this - * register and clear the bit that caused the interrupt. For the R_SS_WC bits, - * the application must write a 1 to the bit to clear the interrupt. - */ -union cvmx_usbcx_hprt { - u32 u32; - /** - * struct cvmx_usbcx_hprt_s - * @prtspd: Port Speed (PrtSpd) - * Indicates the speed of the device attached to this port. - * * 2'b00: High speed - * * 2'b01: Full speed - * * 2'b10: Low speed - * * 2'b11: Reserved - * @prttstctl: Port Test Control (PrtTstCtl) - * The application writes a nonzero value to this field to put - * the port into a Test mode, and the corresponding pattern is - * signaled on the port. - * * 4'b0000: Test mode disabled - * * 4'b0001: Test_J mode - * * 4'b0010: Test_K mode - * * 4'b0011: Test_SE0_NAK mode - * * 4'b0100: Test_Packet mode - * * 4'b0101: Test_Force_Enable - * * Others: Reserved - * PrtSpd must be zero (i.e. the interface must be in high-speed - * mode) to use the PrtTstCtl test modes. - * @prtpwr: Port Power (PrtPwr) - * The application uses this field to control power to this port, - * and the core clears this bit on an overcurrent condition. - * * 1'b0: Power off - * * 1'b1: Power on - * @prtlnsts: Port Line Status (PrtLnSts) - * Indicates the current logic level USB data lines - * * Bit [10]: Logic level of D- - * * Bit [11]: Logic level of D+ - * @prtrst: Port Reset (PrtRst) - * When the application sets this bit, a reset sequence is - * started on this port. The application must time the reset - * period and clear this bit after the reset sequence is - * complete. - * * 1'b0: Port not in reset - * * 1'b1: Port in reset - * The application must leave this bit set for at least a - * minimum duration mentioned below to start a reset on the - * port. The application can leave it set for another 10 ms in - * addition to the required minimum duration, before clearing - * the bit, even though there is no maximum limit set by the - * USB standard. - * * High speed: 50 ms - * * Full speed/Low speed: 10 ms - * @prtsusp: Port Suspend (PrtSusp) - * The application sets this bit to put this port in Suspend - * mode. The core only stops sending SOFs when this is set. - * To stop the PHY clock, the application must set the Port - * Clock Stop bit, which will assert the suspend input pin of - * the PHY. - * The read value of this bit reflects the current suspend - * status of the port. This bit is cleared by the core after a - * remote wakeup signal is detected or the application sets - * the Port Reset bit or Port Resume bit in this register or the - * Resume/Remote Wakeup Detected Interrupt bit or - * Disconnect Detected Interrupt bit in the Core Interrupt - * register (GINTSTS.WkUpInt or GINTSTS.DisconnInt, - * respectively). - * * 1'b0: Port not in Suspend mode - * * 1'b1: Port in Suspend mode - * @prtres: Port Resume (PrtRes) - * The application sets this bit to drive resume signaling on - * the port. The core continues to drive the resume signal - * until the application clears this bit. - * If the core detects a USB remote wakeup sequence, as - * indicated by the Port Resume/Remote Wakeup Detected - * Interrupt bit of the Core Interrupt register - * (GINTSTS.WkUpInt), the core starts driving resume - * signaling without application intervention and clears this bit - * when it detects a disconnect condition. The read value of - * this bit indicates whether the core is currently driving - * resume signaling. - * * 1'b0: No resume driven - * * 1'b1: Resume driven - * @prtovrcurrchng: Port Overcurrent Change (PrtOvrCurrChng) - * The core sets this bit when the status of the Port - * Overcurrent Active bit (bit 4) in this register changes. - * @prtovrcurract: Port Overcurrent Active (PrtOvrCurrAct) - * Indicates the overcurrent condition of the port. - * * 1'b0: No overcurrent condition - * * 1'b1: Overcurrent condition - * @prtenchng: Port Enable/Disable Change (PrtEnChng) - * The core sets this bit when the status of the Port Enable bit - * [2] of this register changes. - * @prtena: Port Enable (PrtEna) - * A port is enabled only by the core after a reset sequence, - * and is disabled by an overcurrent condition, a disconnect - * condition, or by the application clearing this bit. The - * application cannot set this bit by a register write. It can only - * clear it to disable the port. This bit does not trigger any - * interrupt to the application. - * * 1'b0: Port disabled - * * 1'b1: Port enabled - * @prtconndet: Port Connect Detected (PrtConnDet) - * The core sets this bit when a device connection is detected - * to trigger an interrupt to the application using the Host Port - * Interrupt bit of the Core Interrupt register (GINTSTS.PrtInt). - * The application must write a 1 to this bit to clear the - * interrupt. - * @prtconnsts: Port Connect Status (PrtConnSts) - * * 0: No device is attached to the port. - * * 1: A device is attached to the port. - */ - struct cvmx_usbcx_hprt_s { - __BITFIELD_FIELD(u32 reserved_19_31 : 13, - __BITFIELD_FIELD(u32 prtspd : 2, - __BITFIELD_FIELD(u32 prttstctl : 4, - __BITFIELD_FIELD(u32 prtpwr : 1, - __BITFIELD_FIELD(u32 prtlnsts : 2, - __BITFIELD_FIELD(u32 reserved_9_9 : 1, - __BITFIELD_FIELD(u32 prtrst : 1, - __BITFIELD_FIELD(u32 prtsusp : 1, - __BITFIELD_FIELD(u32 prtres : 1, - __BITFIELD_FIELD(u32 prtovrcurrchng : 1, - __BITFIELD_FIELD(u32 prtovrcurract : 1, - __BITFIELD_FIELD(u32 prtenchng : 1, - __BITFIELD_FIELD(u32 prtena : 1, - __BITFIELD_FIELD(u32 prtconndet : 1, - __BITFIELD_FIELD(u32 prtconnsts : 1, - ;))))))))))))))) - } s; -}; - -/** - * cvmx_usbc#_hptxfsiz - * - * Host Periodic Transmit FIFO Size Register (HPTXFSIZ) - * - * This register holds the size and the memory start address of the Periodic - * TxFIFO, as shown in Figures 310 and 311. - */ -union cvmx_usbcx_hptxfsiz { - u32 u32; - /** - * struct cvmx_usbcx_hptxfsiz_s - * @ptxfsize: Host Periodic TxFIFO Depth (PTxFSize) - * This value is in terms of 32-bit words. - * * Minimum value is 16 - * * Maximum value is 32768 - * @ptxfstaddr: Host Periodic TxFIFO Start Address (PTxFStAddr) - */ - struct cvmx_usbcx_hptxfsiz_s { - __BITFIELD_FIELD(u32 ptxfsize : 16, - __BITFIELD_FIELD(u32 ptxfstaddr : 16, - ;)) - } s; -}; - -/** - * cvmx_usbc#_hptxsts - * - * Host Periodic Transmit FIFO/Queue Status Register (HPTXSTS) - * - * This read-only register contains the free space information for the Periodic - * TxFIFO and the Periodic Transmit Request Queue - */ -union cvmx_usbcx_hptxsts { - u32 u32; - /** - * struct cvmx_usbcx_hptxsts_s - * @ptxqtop: Top of the Periodic Transmit Request Queue (PTxQTop) - * This indicates the entry in the Periodic Tx Request Queue that - * is currently being processes by the MAC. - * This register is used for debugging. - * * Bit [31]: Odd/Even (micro)frame - * - 1'b0: send in even (micro)frame - * - 1'b1: send in odd (micro)frame - * * Bits [30:27]: Channel/endpoint number - * * Bits [26:25]: Type - * - 2'b00: IN/OUT - * - 2'b01: Zero-length packet - * - 2'b10: CSPLIT - * - 2'b11: Disable channel command - * * Bit [24]: Terminate (last entry for the selected - * channel/endpoint) - * @ptxqspcavail: Periodic Transmit Request Queue Space Available - * (PTxQSpcAvail) - * Indicates the number of free locations available to be written - * in the Periodic Transmit Request Queue. This queue holds both - * IN and OUT requests. - * * 8'h0: Periodic Transmit Request Queue is full - * * 8'h1: 1 location available - * * 8'h2: 2 locations available - * * n: n locations available (0..8) - * * Others: Reserved - * @ptxfspcavail: Periodic Transmit Data FIFO Space Available - * (PTxFSpcAvail) - * Indicates the number of free locations available to be written - * to in the Periodic TxFIFO. - * Values are in terms of 32-bit words - * * 16'h0: Periodic TxFIFO is full - * * 16'h1: 1 word available - * * 16'h2: 2 words available - * * 16'hn: n words available (where 0..32768) - * * 16'h8000: 32768 words available - * * Others: Reserved - */ - struct cvmx_usbcx_hptxsts_s { - __BITFIELD_FIELD(u32 ptxqtop : 8, - __BITFIELD_FIELD(u32 ptxqspcavail : 8, - __BITFIELD_FIELD(u32 ptxfspcavail : 16, - ;))) - } s; -}; - -/** - * cvmx_usbn#_clk_ctl - * - * USBN_CLK_CTL = USBN's Clock Control - * - * This register is used to control the frequency of the hclk and the - * hreset and phy_rst signals. - */ -union cvmx_usbnx_clk_ctl { - u64 u64; - /** - * struct cvmx_usbnx_clk_ctl_s - * @divide2: The 'hclk' used by the USB subsystem is derived - * from the eclk. - * Also see the field DIVIDE. DIVIDE2<1> must currently - * be zero because it is not implemented, so the maximum - * ratio of eclk/hclk is currently 16. - * The actual divide number for hclk is: - * (DIVIDE2 + 1) * (DIVIDE + 1) - * @hclk_rst: When this field is '0' the HCLK-DIVIDER used to - * generate the hclk in the USB Subsystem is held - * in reset. This bit must be set to '0' before - * changing the value os DIVIDE in this register. - * The reset to the HCLK_DIVIDERis also asserted - * when core reset is asserted. - * @p_x_on: Force USB-PHY on during suspend. - * '1' USB-PHY XO block is powered-down during - * suspend. - * '0' USB-PHY XO block is powered-up during - * suspend. - * The value of this field must be set while POR is - * active. - * @p_rtype: PHY reference clock type - * On CN50XX/CN52XX/CN56XX the values are: - * '0' The USB-PHY uses a 12MHz crystal as a clock source - * at the USB_XO and USB_XI pins. - * '1' Reserved. - * '2' The USB_PHY uses 12/24/48MHz 2.5V board clock at the - * USB_XO pin. USB_XI should be tied to ground in this - * case. - * '3' Reserved. - * On CN3xxx bits 14 and 15 are p_xenbn and p_rclk and values are: - * '0' Reserved. - * '1' Reserved. - * '2' The PHY PLL uses the XO block output as a reference. - * The XO block uses an external clock supplied on the - * XO pin. USB_XI should be tied to ground for this - * usage. - * '3' The XO block uses the clock from a crystal. - * @p_com_on: '0' Force USB-PHY XO Bias, Bandgap and PLL to - * remain powered in Suspend Mode. - * '1' The USB-PHY XO Bias, Bandgap and PLL are - * powered down in suspend mode. - * The value of this field must be set while POR is - * active. - * @p_c_sel: Phy clock speed select. - * Selects the reference clock / crystal frequency. - * '11': Reserved - * '10': 48 MHz (reserved when a crystal is used) - * '01': 24 MHz (reserved when a crystal is used) - * '00': 12 MHz - * The value of this field must be set while POR is - * active. - * NOTE: if a crystal is used as a reference clock, - * this field must be set to 12 MHz. - * @cdiv_byp: Used to enable the bypass input to the USB_CLK_DIV. - * @sd_mode: Scaledown mode for the USBC. Control timing events - * in the USBC, for normal operation this must be '0'. - * @s_bist: Starts bist on the hclk memories, during the '0' - * to '1' transition. - * @por: Power On Reset for the PHY. - * Resets all the PHYS registers and state machines. - * @enable: When '1' allows the generation of the hclk. When - * '0' the hclk will not be generated. SEE DIVIDE - * field of this register. - * @prst: When this field is '0' the reset associated with - * the phy_clk functionality in the USB Subsystem is - * help in reset. This bit should not be set to '1' - * until the time it takes 6 clocks (hclk or phy_clk, - * whichever is slower) has passed. Under normal - * operation once this bit is set to '1' it should not - * be set to '0'. - * @hrst: When this field is '0' the reset associated with - * the hclk functioanlity in the USB Subsystem is - * held in reset.This bit should not be set to '1' - * until 12ms after phy_clk is stable. Under normal - * operation, once this bit is set to '1' it should - * not be set to '0'. - * @divide: The frequency of 'hclk' used by the USB subsystem - * is the eclk frequency divided by the value of - * (DIVIDE2 + 1) * (DIVIDE + 1), also see the field - * DIVIDE2 of this register. - * The hclk frequency should be less than 125Mhz. - * After writing a value to this field the SW should - * read the field for the value written. - * The ENABLE field of this register should not be set - * until AFTER this field is set and then read. - */ - struct cvmx_usbnx_clk_ctl_s { - __BITFIELD_FIELD(u64 reserved_20_63 : 44, - __BITFIELD_FIELD(u64 divide2 : 2, - __BITFIELD_FIELD(u64 hclk_rst : 1, - __BITFIELD_FIELD(u64 p_x_on : 1, - __BITFIELD_FIELD(u64 p_rtype : 2, - __BITFIELD_FIELD(u64 p_com_on : 1, - __BITFIELD_FIELD(u64 p_c_sel : 2, - __BITFIELD_FIELD(u64 cdiv_byp : 1, - __BITFIELD_FIELD(u64 sd_mode : 2, - __BITFIELD_FIELD(u64 s_bist : 1, - __BITFIELD_FIELD(u64 por : 1, - __BITFIELD_FIELD(u64 enable : 1, - __BITFIELD_FIELD(u64 prst : 1, - __BITFIELD_FIELD(u64 hrst : 1, - __BITFIELD_FIELD(u64 divide : 3, - ;))))))))))))))) - } s; -}; - -/** - * cvmx_usbn#_usbp_ctl_status - * - * USBN_USBP_CTL_STATUS = USBP Control And Status Register - * - * Contains general control and status information for the USBN block. - */ -union cvmx_usbnx_usbp_ctl_status { - u64 u64; - /** - * struct cvmx_usbnx_usbp_ctl_status_s - * @txrisetune: HS Transmitter Rise/Fall Time Adjustment - * @txvreftune: HS DC Voltage Level Adjustment - * @txfslstune: FS/LS Source Impedance Adjustment - * @txhsxvtune: Transmitter High-Speed Crossover Adjustment - * @sqrxtune: Squelch Threshold Adjustment - * @compdistune: Disconnect Threshold Adjustment - * @otgtune: VBUS Valid Threshold Adjustment - * @otgdisable: OTG Block Disable - * @portreset: Per_Port Reset - * @drvvbus: Drive VBUS - * @lsbist: Low-Speed BIST Enable. - * @fsbist: Full-Speed BIST Enable. - * @hsbist: High-Speed BIST Enable. - * @bist_done: PHY Bist Done. - * Asserted at the end of the PHY BIST sequence. - * @bist_err: PHY Bist Error. - * Indicates an internal error was detected during - * the BIST sequence. - * @tdata_out: PHY Test Data Out. - * Presents either internally generated signals or - * test register contents, based upon the value of - * test_data_out_sel. - * @siddq: Drives the USBP (USB-PHY) SIDDQ input. - * Normally should be set to zero. - * When customers have no intent to use USB PHY - * interface, they should: - * - still provide 3.3V to USB_VDD33, and - * - tie USB_REXT to 3.3V supply, and - * - set USBN*_USBP_CTL_STATUS[SIDDQ]=1 - * @txpreemphasistune: HS Transmitter Pre-Emphasis Enable - * @dma_bmode: When set to 1 the L2C DMA address will be updated - * with byte-counts between packets. When set to 0 - * the L2C DMA address is incremented to the next - * 4-byte aligned address after adding byte-count. - * @usbc_end: Bigendian input to the USB Core. This should be - * set to '0' for operation. - * @usbp_bist: PHY, This is cleared '0' to run BIST on the USBP. - * @tclk: PHY Test Clock, used to load TDATA_IN to the USBP. - * @dp_pulld: PHY DP_PULLDOWN input to the USB-PHY. - * This signal enables the pull-down resistance on - * the D+ line. '1' pull down-resistance is connected - * to D+/ '0' pull down resistance is not connected - * to D+. When an A/B device is acting as a host - * (downstream-facing port), dp_pulldown and - * dm_pulldown are enabled. This must not toggle - * during normal operation. - * @dm_pulld: PHY DM_PULLDOWN input to the USB-PHY. - * This signal enables the pull-down resistance on - * the D- line. '1' pull down-resistance is connected - * to D-. '0' pull down resistance is not connected - * to D-. When an A/B device is acting as a host - * (downstream-facing port), dp_pulldown and - * dm_pulldown are enabled. This must not toggle - * during normal operation. - * @hst_mode: When '0' the USB is acting as HOST, when '1' - * USB is acting as device. This field needs to be - * set while the USB is in reset. - * @tuning: Transmitter Tuning for High-Speed Operation. - * Tunes the current supply and rise/fall output - * times for high-speed operation. - * [20:19] == 11: Current supply increased - * approximately 9% - * [20:19] == 10: Current supply increased - * approximately 4.5% - * [20:19] == 01: Design default. - * [20:19] == 00: Current supply decreased - * approximately 4.5% - * [22:21] == 11: Rise and fall times are increased. - * [22:21] == 10: Design default. - * [22:21] == 01: Rise and fall times are decreased. - * [22:21] == 00: Rise and fall times are decreased - * further as compared to the 01 setting. - * @tx_bs_enh: Transmit Bit Stuffing on [15:8]. - * Enables or disables bit stuffing on data[15:8] - * when bit-stuffing is enabled. - * @tx_bs_en: Transmit Bit Stuffing on [7:0]. - * Enables or disables bit stuffing on data[7:0] - * when bit-stuffing is enabled. - * @loop_enb: PHY Loopback Test Enable. - * '1': During data transmission the receive is - * enabled. - * '0': During data transmission the receive is - * disabled. - * Must be '0' for normal operation. - * @vtest_enb: Analog Test Pin Enable. - * '1' The PHY's analog_test pin is enabled for the - * input and output of applicable analog test signals. - * '0' THe analog_test pin is disabled. - * @bist_enb: Built-In Self Test Enable. - * Used to activate BIST in the PHY. - * @tdata_sel: Test Data Out Select. - * '1' test_data_out[3:0] (PHY) register contents - * are output. '0' internally generated signals are - * output. - * @taddr_in: Mode Address for Test Interface. - * Specifies the register address for writing to or - * reading from the PHY test interface register. - * @tdata_in: Internal Testing Register Input Data and Select - * This is a test bus. Data is present on [3:0], - * and its corresponding select (enable) is present - * on bits [7:4]. - * @ate_reset: Reset input from automatic test equipment. - * This is a test signal. When the USB Core is - * powered up (not in Susned Mode), an automatic - * tester can use this to disable phy_clock and - * free_clk, then re-enable them with an aligned - * phase. - * '1': The phy_clk and free_clk outputs are - * disabled. "0": The phy_clock and free_clk outputs - * are available within a specific period after the - * de-assertion. - */ - struct cvmx_usbnx_usbp_ctl_status_s { - __BITFIELD_FIELD(u64 txrisetune : 1, - __BITFIELD_FIELD(u64 txvreftune : 4, - __BITFIELD_FIELD(u64 txfslstune : 4, - __BITFIELD_FIELD(u64 txhsxvtune : 2, - __BITFIELD_FIELD(u64 sqrxtune : 3, - __BITFIELD_FIELD(u64 compdistune : 3, - __BITFIELD_FIELD(u64 otgtune : 3, - __BITFIELD_FIELD(u64 otgdisable : 1, - __BITFIELD_FIELD(u64 portreset : 1, - __BITFIELD_FIELD(u64 drvvbus : 1, - __BITFIELD_FIELD(u64 lsbist : 1, - __BITFIELD_FIELD(u64 fsbist : 1, - __BITFIELD_FIELD(u64 hsbist : 1, - __BITFIELD_FIELD(u64 bist_done : 1, - __BITFIELD_FIELD(u64 bist_err : 1, - __BITFIELD_FIELD(u64 tdata_out : 4, - __BITFIELD_FIELD(u64 siddq : 1, - __BITFIELD_FIELD(u64 txpreemphasistune : 1, - __BITFIELD_FIELD(u64 dma_bmode : 1, - __BITFIELD_FIELD(u64 usbc_end : 1, - __BITFIELD_FIELD(u64 usbp_bist : 1, - __BITFIELD_FIELD(u64 tclk : 1, - __BITFIELD_FIELD(u64 dp_pulld : 1, - __BITFIELD_FIELD(u64 dm_pulld : 1, - __BITFIELD_FIELD(u64 hst_mode : 1, - __BITFIELD_FIELD(u64 tuning : 4, - __BITFIELD_FIELD(u64 tx_bs_enh : 1, - __BITFIELD_FIELD(u64 tx_bs_en : 1, - __BITFIELD_FIELD(u64 loop_enb : 1, - __BITFIELD_FIELD(u64 vtest_enb : 1, - __BITFIELD_FIELD(u64 bist_enb : 1, - __BITFIELD_FIELD(u64 tdata_sel : 1, - __BITFIELD_FIELD(u64 taddr_in : 4, - __BITFIELD_FIELD(u64 tdata_in : 8, - __BITFIELD_FIELD(u64 ate_reset : 1, - ;))))))))))))))))))))))))))))))))))) - } s; -}; - -#endif /* __OCTEON_HCD_H__ */ diff --git a/drivers/staging/octeon/Kconfig b/drivers/staging/octeon/Kconfig deleted file mode 100644 index e7f4ddcc1361..000000000000 --- a/drivers/staging/octeon/Kconfig +++ /dev/null @@ -1,16 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0 -config OCTEON_ETHERNET - tristate "Cavium Networks Octeon Ethernet support" - depends on CAVIUM_OCTEON_SOC || COMPILE_TEST - depends on NETDEVICES - depends on BROKEN - select PHYLIB - select MDIO_OCTEON - help - This driver supports the builtin ethernet ports on Cavium - Networks' products in the Octeon family. This driver supports the - CN3XXX and CN5XXX Octeon processors. - - To compile this driver as a module, choose M here. The module - will be called octeon-ethernet. - diff --git a/drivers/staging/octeon/Makefile b/drivers/staging/octeon/Makefile deleted file mode 100644 index 3887cf5f1e84..000000000000 --- a/drivers/staging/octeon/Makefile +++ /dev/null @@ -1,19 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0 -# -# Copyright (C) 2005-2009 Cavium Networks -# - -# -# Makefile for Cavium OCTEON on-board ethernet driver -# - -obj-${CONFIG_OCTEON_ETHERNET} := octeon-ethernet.o - -octeon-ethernet-y := ethernet.o -octeon-ethernet-y += ethernet-mdio.o -octeon-ethernet-y += ethernet-mem.o -octeon-ethernet-y += ethernet-rgmii.o -octeon-ethernet-y += ethernet-rx.o -octeon-ethernet-y += ethernet-sgmii.o -octeon-ethernet-y += ethernet-spi.o -octeon-ethernet-y += ethernet-tx.o diff --git a/drivers/staging/octeon/TODO b/drivers/staging/octeon/TODO deleted file mode 100644 index 67a0a1f6b922..000000000000 --- a/drivers/staging/octeon/TODO +++ /dev/null @@ -1,9 +0,0 @@ -This driver is functional and supports Ethernet on OCTEON+/OCTEON2/OCTEON3 -chips at least up to CN7030. - -TODO: - - general code review and clean up - - make driver self-contained instead of being split between staging and - arch/mips/cavium-octeon. - -Contact: Aaro Koskinen <aaro.koskinen@iki.fi> diff --git a/drivers/staging/octeon/ethernet-defines.h b/drivers/staging/octeon/ethernet-defines.h deleted file mode 100644 index ef9e767b0e2e..000000000000 --- a/drivers/staging/octeon/ethernet-defines.h +++ /dev/null @@ -1,40 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0 */ -/* - * This file is based on code from OCTEON SDK by Cavium Networks. - * - * Copyright (c) 2003-2007 Cavium Networks - */ - -/* - * A few defines are used to control the operation of this driver: - * USE_ASYNC_IOBDMA - * Use asynchronous IO access to hardware. This uses Octeon's asynchronous - * IOBDMAs to issue IO accesses without stalling. Set this to zero - * to disable this. Note that IOBDMAs require CVMSEG. - * REUSE_SKBUFFS_WITHOUT_FREE - * Allows the TX path to free an skbuff into the FPA hardware pool. This - * can significantly improve performance for forwarding and bridging, but - * may be somewhat dangerous. Checks are made, but if any buffer is reused - * without the proper Linux cleanup, the networking stack may have very - * bizarre bugs. - */ -#ifndef __ETHERNET_DEFINES_H__ -#define __ETHERNET_DEFINES_H__ - -#ifdef CONFIG_NETFILTER -#define REUSE_SKBUFFS_WITHOUT_FREE 0 -#else -#define REUSE_SKBUFFS_WITHOUT_FREE 1 -#endif - -#define USE_ASYNC_IOBDMA (CONFIG_CAVIUM_OCTEON_CVMSEG_SIZE > 0) - -/* Maximum number of SKBs to try to free per xmit packet. */ -#define MAX_OUT_QUEUE_DEPTH 1000 - -#define FAU_TOTAL_TX_TO_CLEAN (CVMX_FAU_REG_END - sizeof(u32)) -#define FAU_NUM_PACKET_BUFFERS_TO_FREE (FAU_TOTAL_TX_TO_CLEAN - sizeof(u32)) - -#define TOTAL_NUMBER_OF_PORTS (CVMX_PIP_NUM_INPUT_PORTS + 1) - -#endif /* __ETHERNET_DEFINES_H__ */ diff --git a/drivers/staging/octeon/ethernet-mdio.c b/drivers/staging/octeon/ethernet-mdio.c deleted file mode 100644 index c798672d61b2..000000000000 --- a/drivers/staging/octeon/ethernet-mdio.c +++ /dev/null @@ -1,178 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * This file is based on code from OCTEON SDK by Cavium Networks. - * - * Copyright (c) 2003-2007 Cavium Networks - */ - -#include <linux/kernel.h> -#include <linux/ethtool.h> -#include <linux/phy.h> -#include <linux/ratelimit.h> -#include <linux/of_mdio.h> -#include <generated/utsrelease.h> -#include <net/dst.h> - -#include "octeon-ethernet.h" -#include "ethernet-defines.h" -#include "ethernet-mdio.h" -#include "ethernet-util.h" - -static void cvm_oct_get_drvinfo(struct net_device *dev, - struct ethtool_drvinfo *info) -{ - strlcpy(info->driver, KBUILD_MODNAME, sizeof(info->driver)); - strlcpy(info->version, UTS_RELEASE, sizeof(info->version)); - strlcpy(info->bus_info, "Builtin", sizeof(info->bus_info)); -} - -static int cvm_oct_nway_reset(struct net_device *dev) -{ - if (!capable(CAP_NET_ADMIN)) - return -EPERM; - - if (dev->phydev) - return phy_start_aneg(dev->phydev); - - return -EINVAL; -} - -const struct ethtool_ops cvm_oct_ethtool_ops = { - .get_drvinfo = cvm_oct_get_drvinfo, - .nway_reset = cvm_oct_nway_reset, - .get_link = ethtool_op_get_link, - .get_link_ksettings = phy_ethtool_get_link_ksettings, - .set_link_ksettings = phy_ethtool_set_link_ksettings, -}; - -/** - * cvm_oct_ioctl - IOCTL support for PHY control - * @dev: Device to change - * @rq: the request - * @cmd: the command - * - * Returns Zero on success - */ -int cvm_oct_ioctl(struct net_device *dev, struct ifreq *rq, int cmd) -{ - if (!netif_running(dev)) - return -EINVAL; - - if (!dev->phydev) - return -EINVAL; - - return phy_mii_ioctl(dev->phydev, rq, cmd); -} - -void cvm_oct_note_carrier(struct octeon_ethernet *priv, - union cvmx_helper_link_info li) -{ - if (li.s.link_up) { - pr_notice_ratelimited("%s: %u Mbps %s duplex, port %d, queue %d\n", - netdev_name(priv->netdev), li.s.speed, - (li.s.full_duplex) ? "Full" : "Half", - priv->port, priv->queue); - } else { - pr_notice_ratelimited("%s: Link down\n", - netdev_name(priv->netdev)); - } -} - -void cvm_oct_adjust_link(struct net_device *dev) -{ - struct octeon_ethernet *priv = netdev_priv(dev); - union cvmx_helper_link_info link_info; - - link_info.u64 = 0; - link_info.s.link_up = dev->phydev->link ? 1 : 0; - link_info.s.full_duplex = dev->phydev->duplex ? 1 : 0; - link_info.s.speed = dev->phydev->speed; - priv->link_info = link_info.u64; - - /* - * The polling task need to know about link status changes. - */ - if (priv->poll) - priv->poll(dev); - - if (priv->last_link != dev->phydev->link) { - priv->last_link = dev->phydev->link; - cvmx_helper_link_set(priv->port, link_info); - cvm_oct_note_carrier(priv, link_info); - } -} - -int cvm_oct_common_stop(struct net_device *dev) -{ - struct octeon_ethernet *priv = netdev_priv(dev); - int interface = INTERFACE(priv->port); - union cvmx_helper_link_info link_info; - union cvmx_gmxx_prtx_cfg gmx_cfg; - int index = INDEX(priv->port); - - gmx_cfg.u64 = cvmx_read_csr(CVMX_GMXX_PRTX_CFG(index, interface)); - gmx_cfg.s.en = 0; - cvmx_write_csr(CVMX_GMXX_PRTX_CFG(index, interface), gmx_cfg.u64); - - priv->poll = NULL; - - if (dev->phydev) - phy_disconnect(dev->phydev); - - if (priv->last_link) { - link_info.u64 = 0; - priv->last_link = 0; - - cvmx_helper_link_set(priv->port, link_info); - cvm_oct_note_carrier(priv, link_info); - } - return 0; -} - -/** - * cvm_oct_phy_setup_device - setup the PHY - * - * @dev: Device to setup - * - * Returns Zero on success, negative on failure - */ -int cvm_oct_phy_setup_device(struct net_device *dev) -{ - struct octeon_ethernet *priv = netdev_priv(dev); - struct device_node *phy_node; - struct phy_device *phydev = NULL; - - if (!priv->of_node) - goto no_phy; - - phy_node = of_parse_phandle(priv->of_node, "phy-handle", 0); - if (!phy_node && of_phy_is_fixed_link(priv->of_node)) { - int rc; - - rc = of_phy_register_fixed_link(priv->of_node); - if (rc) - return rc; - - phy_node = of_node_get(priv->of_node); - } - if (!phy_node) - goto no_phy; - - phydev = of_phy_connect(dev, phy_node, cvm_oct_adjust_link, 0, - priv->phy_mode); - of_node_put(phy_node); - - if (!phydev) - return -ENODEV; - - priv->last_link = 0; - phy_start(phydev); - - return 0; -no_phy: - /* If there is no phy, assume a direct MAC connection and that - * the link is up. - */ - netif_carrier_on(dev); - return 0; -} diff --git a/drivers/staging/octeon/ethernet-mdio.h b/drivers/staging/octeon/ethernet-mdio.h deleted file mode 100644 index e3771d48c49b..000000000000 --- a/drivers/staging/octeon/ethernet-mdio.h +++ /dev/null @@ -1,28 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0 */ -/* - * This file is based on code from OCTEON SDK by Cavium Networks. - * - * Copyright (c) 2003-2007 Cavium Networks - */ - -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/netdevice.h> -#include <linux/etherdevice.h> -#include <linux/ip.h> -#include <linux/string.h> -#include <linux/ethtool.h> -#include <linux/seq_file.h> -#include <linux/proc_fs.h> -#include <net/dst.h> -#ifdef CONFIG_XFRM -#include <linux/xfrm.h> -#include <net/xfrm.h> -#endif /* CONFIG_XFRM */ - -extern const struct ethtool_ops cvm_oct_ethtool_ops; - -void octeon_mdiobus_force_mod_depencency(void); - -int cvm_oct_ioctl(struct net_device *dev, struct ifreq *rq, int cmd); -int cvm_oct_phy_setup_device(struct net_device *dev); diff --git a/drivers/staging/octeon/ethernet-mem.c b/drivers/staging/octeon/ethernet-mem.c deleted file mode 100644 index 532594957ebc..000000000000 --- a/drivers/staging/octeon/ethernet-mem.c +++ /dev/null @@ -1,154 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * This file is based on code from OCTEON SDK by Cavium Networks. - * - * Copyright (c) 2003-2010 Cavium Networks - */ - -#include <linux/kernel.h> -#include <linux/netdevice.h> -#include <linux/slab.h> - -#include "octeon-ethernet.h" -#include "ethernet-mem.h" -#include "ethernet-defines.h" - -/** - * cvm_oct_fill_hw_skbuff - fill the supplied hardware pool with skbuffs - * @pool: Pool to allocate an skbuff for - * @size: Size of the buffer needed for the pool - * @elements: Number of buffers to allocate - * - * Returns the actual number of buffers allocated. - */ -static int cvm_oct_fill_hw_skbuff(int pool, int size, int elements) -{ - int freed = elements; - - while (freed) { - struct sk_buff *skb = dev_alloc_skb(size + 256); - - if (unlikely(!skb)) - break; - skb_reserve(skb, 256 - (((unsigned long)skb->data) & 0x7f)); - *(struct sk_buff **)(skb->data - sizeof(void *)) = skb; - cvmx_fpa_free(skb->data, pool, size / 128); - freed--; - } - return elements - freed; -} - -/** - * cvm_oct_free_hw_skbuff- free hardware pool skbuffs - * @pool: Pool to allocate an skbuff for - * @size: Size of the buffer needed for the pool - * @elements: Number of buffers to allocate - */ -static void cvm_oct_free_hw_skbuff(int pool, int size, int elements) -{ - char *memory; - - do { - memory = cvmx_fpa_alloc(pool); - if (memory) { - struct sk_buff *skb = - *(struct sk_buff **)(memory - sizeof(void *)); - elements--; - dev_kfree_skb(skb); - } - } while (memory); - - if (elements < 0) - pr_warn("Freeing of pool %u had too many skbuffs (%d)\n", - pool, elements); - else if (elements > 0) - pr_warn("Freeing of pool %u is missing %d skbuffs\n", - pool, elements); -} - -/** - * cvm_oct_fill_hw_memory - fill a hardware pool with memory. - * @pool: Pool to populate - * @size: Size of each buffer in the pool - * @elements: Number of buffers to allocate - * - * Returns the actual number of buffers allocated. - */ -static int cvm_oct_fill_hw_memory(int pool, int size, int elements) -{ - char *memory; - char *fpa; - int freed = elements; - - while (freed) { - /* - * FPA memory must be 128 byte aligned. Since we are - * aligning we need to save the original pointer so we - * can feed it to kfree when the memory is returned to - * the kernel. - * - * We allocate an extra 256 bytes to allow for - * alignment and space for the original pointer saved - * just before the block. - */ - memory = kmalloc(size + 256, GFP_ATOMIC); - if (unlikely(!memory)) { - pr_warn("Unable to allocate %u bytes for FPA pool %d\n", - elements * size, pool); - break; - } - fpa = (char *)(((unsigned long)memory + 256) & ~0x7fUL); - *((char **)fpa - 1) = memory; - cvmx_fpa_free(fpa, pool, 0); - freed--; - } - return elements - freed; -} - -/** - * cvm_oct_free_hw_memory - Free memory allocated by cvm_oct_fill_hw_memory - * @pool: FPA pool to free - * @size: Size of each buffer in the pool - * @elements: Number of buffers that should be in the pool - */ -static void cvm_oct_free_hw_memory(int pool, int size, int elements) -{ - char *memory; - char *fpa; - - do { - fpa = cvmx_fpa_alloc(pool); - if (fpa) { - elements--; - fpa = (char *)phys_to_virt(cvmx_ptr_to_phys(fpa)); - memory = *((char **)fpa - 1); - kfree(memory); - } - } while (fpa); - - if (elements < 0) - pr_warn("Freeing of pool %u had too many buffers (%d)\n", - pool, elements); - else if (elements > 0) - pr_warn("Warning: Freeing of pool %u is missing %d buffers\n", - pool, elements); -} - -int cvm_oct_mem_fill_fpa(int pool, int size, int elements) -{ - int freed; - - if (pool == CVMX_FPA_PACKET_POOL) - freed = cvm_oct_fill_hw_skbuff(pool, size, elements); - else - freed = cvm_oct_fill_hw_memory(pool, size, elements); - return freed; -} - -void cvm_oct_mem_empty_fpa(int pool, int size, int elements) -{ - if (pool == CVMX_FPA_PACKET_POOL) - cvm_oct_free_hw_skbuff(pool, size, elements); - else - cvm_oct_free_hw_memory(pool, size, elements); -} diff --git a/drivers/staging/octeon/ethernet-mem.h b/drivers/staging/octeon/ethernet-mem.h deleted file mode 100644 index 692dcdb7154d..000000000000 --- a/drivers/staging/octeon/ethernet-mem.h +++ /dev/null @@ -1,9 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0 */ -/* - * This file is based on code from OCTEON SDK by Cavium Networks. - * - * Copyright (c) 2003-2007 Cavium Networks - */ - -int cvm_oct_mem_fill_fpa(int pool, int size, int elements); -void cvm_oct_mem_empty_fpa(int pool, int size, int elements); diff --git a/drivers/staging/octeon/ethernet-rgmii.c b/drivers/staging/octeon/ethernet-rgmii.c deleted file mode 100644 index 0c4fac31540a..000000000000 --- a/drivers/staging/octeon/ethernet-rgmii.c +++ /dev/null @@ -1,158 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * This file is based on code from OCTEON SDK by Cavium Networks. - * - * Copyright (c) 2003-2007 Cavium Networks - */ - -#include <linux/kernel.h> -#include <linux/netdevice.h> -#include <linux/interrupt.h> -#include <linux/phy.h> -#include <linux/ratelimit.h> -#include <net/dst.h> - -#include "octeon-ethernet.h" -#include "ethernet-defines.h" -#include "ethernet-util.h" -#include "ethernet-mdio.h" - -static DEFINE_SPINLOCK(global_register_lock); - -static void cvm_oct_set_hw_preamble(struct octeon_ethernet *priv, bool enable) -{ - union cvmx_gmxx_rxx_frm_ctl gmxx_rxx_frm_ctl; - union cvmx_ipd_sub_port_fcs ipd_sub_port_fcs; - union cvmx_gmxx_rxx_int_reg gmxx_rxx_int_reg; - int interface = INTERFACE(priv->port); - int index = INDEX(priv->port); - - /* Set preamble checking. */ - gmxx_rxx_frm_ctl.u64 = cvmx_read_csr(CVMX_GMXX_RXX_FRM_CTL(index, - interface)); - gmxx_rxx_frm_ctl.s.pre_chk = enable; - cvmx_write_csr(CVMX_GMXX_RXX_FRM_CTL(index, interface), - gmxx_rxx_frm_ctl.u64); - - /* Set FCS stripping. */ - ipd_sub_port_fcs.u64 = cvmx_read_csr(CVMX_IPD_SUB_PORT_FCS); - if (enable) - ipd_sub_port_fcs.s.port_bit |= 1ull << priv->port; - else - ipd_sub_port_fcs.s.port_bit &= - 0xffffffffull ^ (1ull << priv->port); - cvmx_write_csr(CVMX_IPD_SUB_PORT_FCS, ipd_sub_port_fcs.u64); - - /* Clear any error bits. */ - gmxx_rxx_int_reg.u64 = cvmx_read_csr(CVMX_GMXX_RXX_INT_REG(index, - interface)); - cvmx_write_csr(CVMX_GMXX_RXX_INT_REG(index, interface), - gmxx_rxx_int_reg.u64); -} - -static void cvm_oct_check_preamble_errors(struct net_device *dev) -{ - struct octeon_ethernet *priv = netdev_priv(dev); - union cvmx_helper_link_info link_info; - unsigned long flags; - - link_info.u64 = priv->link_info; - - /* - * Take the global register lock since we are going to - * touch registers that affect more than one port. - */ - spin_lock_irqsave(&global_register_lock, flags); - - if (link_info.s.speed == 10 && priv->last_speed == 10) { - /* - * Read the GMXX_RXX_INT_REG[PCTERR] bit and see if we are - * getting preamble errors. - */ - int interface = INTERFACE(priv->port); - int index = INDEX(priv->port); - union cvmx_gmxx_rxx_int_reg gmxx_rxx_int_reg; - - gmxx_rxx_int_reg.u64 = cvmx_read_csr(CVMX_GMXX_RXX_INT_REG - (index, interface)); - if (gmxx_rxx_int_reg.s.pcterr) { - /* - * We are getting preamble errors at 10Mbps. Most - * likely the PHY is giving us packets with misaligned - * preambles. In order to get these packets we need to - * disable preamble checking and do it in software. - */ - cvm_oct_set_hw_preamble(priv, false); - printk_ratelimited("%s: Using 10Mbps with software preamble removal\n", - dev->name); - } - } else { - /* - * Since the 10Mbps preamble workaround is allowed we need to - * enable preamble checking, FCS stripping, and clear error - * bits on every speed change. If errors occur during 10Mbps - * operation the above code will change this stuff - */ - if (priv->last_speed != link_info.s.speed) - cvm_oct_set_hw_preamble(priv, true); - priv->last_speed = link_info.s.speed; - } - spin_unlock_irqrestore(&global_register_lock, flags); -} - -static void cvm_oct_rgmii_poll(struct net_device *dev) -{ - struct octeon_ethernet *priv = netdev_priv(dev); - union cvmx_helper_link_info link_info; - bool status_change; - - link_info = cvmx_helper_link_get(priv->port); - if (priv->link_info != link_info.u64 && - cvmx_helper_link_set(priv->port, link_info)) - link_info.u64 = priv->link_info; - status_change = priv->link_info != link_info.u64; - priv->link_info = link_info.u64; - - cvm_oct_check_preamble_errors(dev); - - if (likely(!status_change)) - return; - - /* Tell core. */ - if (link_info.s.link_up) { - if (!netif_carrier_ok(dev)) - netif_carrier_on(dev); - } else if (netif_carrier_ok(dev)) { - netif_carrier_off(dev); - } - cvm_oct_note_carrier(priv, link_info); -} - -int cvm_oct_rgmii_open(struct net_device *dev) -{ - struct octeon_ethernet *priv = netdev_priv(dev); - int ret; - - ret = cvm_oct_common_open(dev, cvm_oct_rgmii_poll); - if (ret) - return ret; - - if (dev->phydev) { - /* - * In phydev mode, we need still periodic polling for the - * preamble error checking, and we also need to call this - * function on every link state change. - * - * Only true RGMII ports need to be polled. In GMII mode, port - * 0 is really a RGMII port. - */ - if ((priv->imode == CVMX_HELPER_INTERFACE_MODE_GMII && - priv->port == 0) || - (priv->imode == CVMX_HELPER_INTERFACE_MODE_RGMII)) { - priv->poll = cvm_oct_check_preamble_errors; - cvm_oct_check_preamble_errors(dev); - } - } - - return 0; -} diff --git a/drivers/staging/octeon/ethernet-rx.c b/drivers/staging/octeon/ethernet-rx.c deleted file mode 100644 index 2c16230f993c..000000000000 --- a/drivers/staging/octeon/ethernet-rx.c +++ /dev/null @@ -1,538 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * This file is based on code from OCTEON SDK by Cavium Networks. - * - * Copyright (c) 2003-2010 Cavium Networks - */ - -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/cache.h> -#include <linux/cpumask.h> -#include <linux/netdevice.h> -#include <linux/etherdevice.h> -#include <linux/ip.h> -#include <linux/string.h> -#include <linux/prefetch.h> -#include <linux/ratelimit.h> -#include <linux/smp.h> -#include <linux/interrupt.h> -#include <net/dst.h> -#ifdef CONFIG_XFRM -#include <linux/xfrm.h> -#include <net/xfrm.h> -#endif /* CONFIG_XFRM */ - -#include "octeon-ethernet.h" -#include "ethernet-defines.h" -#include "ethernet-mem.h" -#include "ethernet-rx.h" -#include "ethernet-util.h" - -static atomic_t oct_rx_ready = ATOMIC_INIT(0); - -static struct oct_rx_group { - int irq; - int group; - struct napi_struct napi; -} oct_rx_group[16]; - -/** - * cvm_oct_do_interrupt - interrupt handler. - * @irq: Interrupt number. - * @napi_id: Cookie to identify the NAPI instance. - * - * The interrupt occurs whenever the POW has packets in our group. - * - */ -static irqreturn_t cvm_oct_do_interrupt(int irq, void *napi_id) -{ - /* Disable the IRQ and start napi_poll. */ - disable_irq_nosync(irq); - napi_schedule(napi_id); - - return IRQ_HANDLED; -} - -/** - * cvm_oct_check_rcv_error - process receive errors - * @work: Work queue entry pointing to the packet. - * - * Returns Non-zero if the packet can be dropped, zero otherwise. - */ -static inline int cvm_oct_check_rcv_error(struct cvmx_wqe *work) -{ - int port; - - if (octeon_has_feature(OCTEON_FEATURE_PKND)) - port = work->word0.pip.cn68xx.pknd; - else - port = work->word1.cn38xx.ipprt; - - if ((work->word2.snoip.err_code == 10) && (work->word1.len <= 64)) { - /* - * Ignore length errors on min size packets. Some - * equipment incorrectly pads packets to 64+4FCS - * instead of 60+4FCS. Note these packets still get - * counted as frame errors. - */ - } else if (work->word2.snoip.err_code == 5 || - work->word2.snoip.err_code == 7) { - /* - * We received a packet with either an alignment error - * or a FCS error. This may be signalling that we are - * running 10Mbps with GMXX_RXX_FRM_CTL[PRE_CHK] - * off. If this is the case we need to parse the - * packet to determine if we can remove a non spec - * preamble and generate a correct packet. - */ - int interface = cvmx_helper_get_interface_num(port); - int index = cvmx_helper_get_interface_index_num(port); - union cvmx_gmxx_rxx_frm_ctl gmxx_rxx_frm_ctl; - - gmxx_rxx_frm_ctl.u64 = - cvmx_read_csr(CVMX_GMXX_RXX_FRM_CTL(index, interface)); - if (gmxx_rxx_frm_ctl.s.pre_chk == 0) { - u8 *ptr = - cvmx_phys_to_ptr(work->packet_ptr.s.addr); - int i = 0; - - while (i < work->word1.len - 1) { - if (*ptr != 0x55) - break; - ptr++; - i++; - } - - if (*ptr == 0xd5) { - /* Port received 0xd5 preamble */ - work->packet_ptr.s.addr += i + 1; - work->word1.len -= i + 5; - } else if ((*ptr & 0xf) == 0xd) { - /* Port received 0xd preamble */ - work->packet_ptr.s.addr += i; - work->word1.len -= i + 4; - for (i = 0; i < work->word1.len; i++) { - *ptr = - ((*ptr & 0xf0) >> 4) | - ((*(ptr + 1) & 0xf) << 4); - ptr++; - } - } else { - printk_ratelimited("Port %d unknown preamble, packet dropped\n", - port); - cvm_oct_free_work(work); - return 1; - } - } - } else { - printk_ratelimited("Port %d receive error code %d, packet dropped\n", - port, work->word2.snoip.err_code); - cvm_oct_free_work(work); - return 1; - } - - return 0; -} - -static void copy_segments_to_skb(struct cvmx_wqe *work, struct sk_buff *skb) -{ - int segments = work->word2.s.bufs; - union cvmx_buf_ptr segment_ptr = work->packet_ptr; - int len = work->word1.len; - int segment_size; - - while (segments--) { - union cvmx_buf_ptr next_ptr; - - next_ptr = *(union cvmx_buf_ptr *) - cvmx_phys_to_ptr(segment_ptr.s.addr - 8); - - /* - * Octeon Errata PKI-100: The segment size is wrong. - * - * Until it is fixed, calculate the segment size based on - * the packet pool buffer size. - * When it is fixed, the following line should be replaced - * with this one: - * int segment_size = segment_ptr.s.size; - */ - segment_size = - CVMX_FPA_PACKET_POOL_SIZE - - (segment_ptr.s.addr - - (((segment_ptr.s.addr >> 7) - - segment_ptr.s.back) << 7)); - - /* Don't copy more than what is left in the packet */ - if (segment_size > len) - segment_size = len; - - /* Copy the data into the packet */ - skb_put_data(skb, cvmx_phys_to_ptr(segment_ptr.s.addr), - segment_size); - len -= segment_size; - segment_ptr = next_ptr; - } -} - -static int cvm_oct_poll(struct oct_rx_group *rx_group, int budget) -{ - const int coreid = cvmx_get_core_num(); - u64 old_group_mask; - u64 old_scratch; - int rx_count = 0; - int did_work_request = 0; - int packet_not_copied; - - /* Prefetch cvm_oct_device since we know we need it soon */ - prefetch(cvm_oct_device); - - if (USE_ASYNC_IOBDMA) { - /* Save scratch in case userspace is using it */ - CVMX_SYNCIOBDMA; - old_scratch = cvmx_scratch_read64(CVMX_SCR_SCRATCH); - } - - /* Only allow work for our group (and preserve priorities) */ - if (OCTEON_IS_MODEL(OCTEON_CN68XX)) { - old_group_mask = cvmx_read_csr(CVMX_SSO_PPX_GRP_MSK(coreid)); - cvmx_write_csr(CVMX_SSO_PPX_GRP_MSK(coreid), - BIT(rx_group->group)); - cvmx_read_csr(CVMX_SSO_PPX_GRP_MSK(coreid)); /* Flush */ - } else { - old_group_mask = cvmx_read_csr(CVMX_POW_PP_GRP_MSKX(coreid)); - cvmx_write_csr(CVMX_POW_PP_GRP_MSKX(coreid), - (old_group_mask & ~0xFFFFull) | - BIT(rx_group->group)); - } - - if (USE_ASYNC_IOBDMA) { - cvmx_pow_work_request_async(CVMX_SCR_SCRATCH, CVMX_POW_NO_WAIT); - did_work_request = 1; - } - - while (rx_count < budget) { - struct sk_buff *skb = NULL; - struct sk_buff **pskb = NULL; - int skb_in_hw; - struct cvmx_wqe *work; - int port; - - if (USE_ASYNC_IOBDMA && did_work_request) - work = cvmx_pow_work_response_async(CVMX_SCR_SCRATCH); - else - work = cvmx_pow_work_request_sync(CVMX_POW_NO_WAIT); - - prefetch(work); - did_work_request = 0; - if (!work) { - if (OCTEON_IS_MODEL(OCTEON_CN68XX)) { - cvmx_write_csr(CVMX_SSO_WQ_IQ_DIS, - BIT(rx_group->group)); - cvmx_write_csr(CVMX_SSO_WQ_INT, - BIT(rx_group->group)); - } else { - union cvmx_pow_wq_int wq_int; - - wq_int.u64 = 0; - wq_int.s.iq_dis = BIT(rx_group->group); - wq_int.s.wq_int = BIT(rx_group->group); - cvmx_write_csr(CVMX_POW_WQ_INT, wq_int.u64); - } - break; - } - pskb = (struct sk_buff **) - (cvm_oct_get_buffer_ptr(work->packet_ptr) - - sizeof(void *)); - prefetch(pskb); - - if (USE_ASYNC_IOBDMA && rx_count < (budget - 1)) { - cvmx_pow_work_request_async_nocheck(CVMX_SCR_SCRATCH, - CVMX_POW_NO_WAIT); - did_work_request = 1; - } - rx_count++; - - skb_in_hw = work->word2.s.bufs == 1; - if (likely(skb_in_hw)) { - skb = *pskb; - prefetch(&skb->head); - prefetch(&skb->len); - } - - if (octeon_has_feature(OCTEON_FEATURE_PKND)) - port = work->word0.pip.cn68xx.pknd; - else - port = work->word1.cn38xx.ipprt; - - prefetch(cvm_oct_device[port]); - - /* Immediately throw away all packets with receive errors */ - if (unlikely(work->word2.snoip.rcv_error)) { - if (cvm_oct_check_rcv_error(work)) - continue; - } - - /* - * We can only use the zero copy path if skbuffs are - * in the FPA pool and the packet fits in a single - * buffer. - */ - if (likely(skb_in_hw)) { - skb->data = skb->head + work->packet_ptr.s.addr - - cvmx_ptr_to_phys(skb->head); - prefetch(skb->data); - skb->len = work->word1.len; - skb_set_tail_pointer(skb, skb->len); - packet_not_copied = 1; - } else { - /* - * We have to copy the packet. First allocate - * an skbuff for it. - */ - skb = dev_alloc_skb(work->word1.len); - if (!skb) { - cvm_oct_free_work(work); - continue; - } - - /* - * Check if we've received a packet that was - * entirely stored in the work entry. - */ - if (unlikely(work->word2.s.bufs == 0)) { - u8 *ptr = work->packet_data; - - if (likely(!work->word2.s.not_IP)) { - /* - * The beginning of the packet - * moves for IP packets. - */ - if (work->word2.s.is_v6) - ptr += 2; - else - ptr += 6; - } - skb_put_data(skb, ptr, work->word1.len); - /* No packet buffers to free */ - } else { - copy_segments_to_skb(work, skb); - } - packet_not_copied = 0; - } - if (likely((port < TOTAL_NUMBER_OF_PORTS) && - cvm_oct_device[port])) { - struct net_device *dev = cvm_oct_device[port]; - - /* - * Only accept packets for devices that are - * currently up. - */ - if (likely(dev->flags & IFF_UP)) { - skb->protocol = eth_type_trans(skb, dev); - skb->dev = dev; - - if (unlikely(work->word2.s.not_IP || - work->word2.s.IP_exc || - work->word2.s.L4_error || - !work->word2.s.tcp_or_udp)) - skb->ip_summed = CHECKSUM_NONE; - else - skb->ip_summed = CHECKSUM_UNNECESSARY; - - /* Increment RX stats for virtual ports */ - if (port >= CVMX_PIP_NUM_INPUT_PORTS) { - dev->stats.rx_packets++; - dev->stats.rx_bytes += skb->len; - } - netif_receive_skb(skb); - } else { - /* - * Drop any packet received for a device that - * isn't up. - */ - dev->stats.rx_dropped++; - dev_kfree_skb_irq(skb); - } - } else { - /* - * Drop any packet received for a device that - * doesn't exist. - */ - printk_ratelimited("Port %d not controlled by Linux, packet dropped\n", - port); - dev_kfree_skb_irq(skb); - } - /* - * Check to see if the skbuff and work share the same - * packet buffer. - */ - if (likely(packet_not_copied)) { - /* - * This buffer needs to be replaced, increment - * the number of buffers we need to free by - * one. - */ - cvmx_fau_atomic_add32(FAU_NUM_PACKET_BUFFERS_TO_FREE, - 1); - - cvmx_fpa_free(work, CVMX_FPA_WQE_POOL, 1); - } else { - cvm_oct_free_work(work); - } - } - /* Restore the original POW group mask */ - if (OCTEON_IS_MODEL(OCTEON_CN68XX)) { - cvmx_write_csr(CVMX_SSO_PPX_GRP_MSK(coreid), old_group_mask); - cvmx_read_csr(CVMX_SSO_PPX_GRP_MSK(coreid)); /* Flush */ - } else { - cvmx_write_csr(CVMX_POW_PP_GRP_MSKX(coreid), old_group_mask); - } - - if (USE_ASYNC_IOBDMA) { - /* Restore the scratch area */ - cvmx_scratch_write64(CVMX_SCR_SCRATCH, old_scratch); - } - cvm_oct_rx_refill_pool(0); - - return rx_count; -} - -/** - * cvm_oct_napi_poll - the NAPI poll function. - * @napi: The NAPI instance. - * @budget: Maximum number of packets to receive. - * - * Returns the number of packets processed. - */ -static int cvm_oct_napi_poll(struct napi_struct *napi, int budget) -{ - struct oct_rx_group *rx_group = container_of(napi, struct oct_rx_group, - napi); - int rx_count; - - rx_count = cvm_oct_poll(rx_group, budget); - - if (rx_count < budget) { - /* No more work */ - napi_complete_done(napi, rx_count); - enable_irq(rx_group->irq); - } - return rx_count; -} - -#ifdef CONFIG_NET_POLL_CONTROLLER -/** - * cvm_oct_poll_controller - poll for receive packets - * device. - * - * @dev: Device to poll. Unused - */ -void cvm_oct_poll_controller(struct net_device *dev) -{ - int i; - - if (!atomic_read(&oct_rx_ready)) - return; - - for (i = 0; i < ARRAY_SIZE(oct_rx_group); i++) { - if (!(pow_receive_groups & BIT(i))) - continue; - - cvm_oct_poll(&oct_rx_group[i], 16); - } -} -#endif - -void cvm_oct_rx_initialize(void) -{ - int i; - struct net_device *dev_for_napi = NULL; - - for (i = 0; i < TOTAL_NUMBER_OF_PORTS; i++) { - if (cvm_oct_device[i]) { - dev_for_napi = cvm_oct_device[i]; - break; - } - } - - if (!dev_for_napi) - panic("No net_devices were allocated."); - - for (i = 0; i < ARRAY_SIZE(oct_rx_group); i++) { - int ret; - - if (!(pow_receive_groups & BIT(i))) - continue; - - netif_napi_add(dev_for_napi, &oct_rx_group[i].napi, - cvm_oct_napi_poll, rx_napi_weight); - napi_enable(&oct_rx_group[i].napi); - - oct_rx_group[i].irq = OCTEON_IRQ_WORKQ0 + i; - oct_rx_group[i].group = i; - - /* Register an IRQ handler to receive POW interrupts */ - ret = request_irq(oct_rx_group[i].irq, cvm_oct_do_interrupt, 0, - "Ethernet", &oct_rx_group[i].napi); - if (ret) - panic("Could not acquire Ethernet IRQ %d\n", - oct_rx_group[i].irq); - - disable_irq_nosync(oct_rx_group[i].irq); - - /* Enable POW interrupt when our port has at least one packet */ - if (OCTEON_IS_MODEL(OCTEON_CN68XX)) { - union cvmx_sso_wq_int_thrx int_thr; - union cvmx_pow_wq_int_pc int_pc; - - int_thr.u64 = 0; - int_thr.s.tc_en = 1; - int_thr.s.tc_thr = 1; - cvmx_write_csr(CVMX_SSO_WQ_INT_THRX(i), int_thr.u64); - - int_pc.u64 = 0; - int_pc.s.pc_thr = 5; - cvmx_write_csr(CVMX_SSO_WQ_INT_PC, int_pc.u64); - } else { - union cvmx_pow_wq_int_thrx int_thr; - union cvmx_pow_wq_int_pc int_pc; - - int_thr.u64 = 0; - int_thr.s.tc_en = 1; - int_thr.s.tc_thr = 1; - cvmx_write_csr(CVMX_POW_WQ_INT_THRX(i), int_thr.u64); - - int_pc.u64 = 0; - int_pc.s.pc_thr = 5; - cvmx_write_csr(CVMX_POW_WQ_INT_PC, int_pc.u64); - } - - /* Schedule NAPI now. This will indirectly enable the - * interrupt. - */ - napi_schedule(&oct_rx_group[i].napi); - } - atomic_inc(&oct_rx_ready); -} - -void cvm_oct_rx_shutdown(void) -{ - int i; - - for (i = 0; i < ARRAY_SIZE(oct_rx_group); i++) { - if (!(pow_receive_groups & BIT(i))) - continue; - - /* Disable POW interrupt */ - if (OCTEON_IS_MODEL(OCTEON_CN68XX)) - cvmx_write_csr(CVMX_SSO_WQ_INT_THRX(i), 0); - else - cvmx_write_csr(CVMX_POW_WQ_INT_THRX(i), 0); - - /* Free the interrupt handler */ - free_irq(oct_rx_group[i].irq, cvm_oct_device); - - netif_napi_del(&oct_rx_group[i].napi); - } -} diff --git a/drivers/staging/octeon/ethernet-rx.h b/drivers/staging/octeon/ethernet-rx.h deleted file mode 100644 index ff6482fa20d6..000000000000 --- a/drivers/staging/octeon/ethernet-rx.h +++ /dev/null @@ -1,31 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0 */ -/* - * This file is based on code from OCTEON SDK by Cavium Networks. - * - * Copyright (c) 2003-2007 Cavium Networks - */ - -void cvm_oct_poll_controller(struct net_device *dev); -void cvm_oct_rx_initialize(void); -void cvm_oct_rx_shutdown(void); - -static inline void cvm_oct_rx_refill_pool(int fill_threshold) -{ - int number_to_free; - int num_freed; - /* Refill the packet buffer pool */ - number_to_free = - cvmx_fau_fetch_and_add32(FAU_NUM_PACKET_BUFFERS_TO_FREE, 0); - - if (number_to_free > fill_threshold) { - cvmx_fau_atomic_add32(FAU_NUM_PACKET_BUFFERS_TO_FREE, - -number_to_free); - num_freed = cvm_oct_mem_fill_fpa(CVMX_FPA_PACKET_POOL, - CVMX_FPA_PACKET_POOL_SIZE, - number_to_free); - if (num_freed != number_to_free) { - cvmx_fau_atomic_add32(FAU_NUM_PACKET_BUFFERS_TO_FREE, - number_to_free - num_freed); - } - } -} diff --git a/drivers/staging/octeon/ethernet-sgmii.c b/drivers/staging/octeon/ethernet-sgmii.c deleted file mode 100644 index d7fbd9159302..000000000000 --- a/drivers/staging/octeon/ethernet-sgmii.c +++ /dev/null @@ -1,30 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * This file is based on code from OCTEON SDK by Cavium Networks. - * - * Copyright (c) 2003-2007 Cavium Networks - */ - -#include <linux/phy.h> -#include <linux/kernel.h> -#include <linux/netdevice.h> -#include <linux/ratelimit.h> -#include <net/dst.h> - -#include "octeon-ethernet.h" -#include "ethernet-defines.h" -#include "ethernet-util.h" -#include "ethernet-mdio.h" - -int cvm_oct_sgmii_open(struct net_device *dev) -{ - return cvm_oct_common_open(dev, cvm_oct_link_poll); -} - -int cvm_oct_sgmii_init(struct net_device *dev) -{ - cvm_oct_common_init(dev); - - /* FIXME: Need autoneg logic */ - return 0; -} diff --git a/drivers/staging/octeon/ethernet-spi.c b/drivers/staging/octeon/ethernet-spi.c deleted file mode 100644 index c582403e6a1f..000000000000 --- a/drivers/staging/octeon/ethernet-spi.c +++ /dev/null @@ -1,226 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * This file is based on code from OCTEON SDK by Cavium Networks. - * - * Copyright (c) 2003-2007 Cavium Networks - */ - -#include <linux/kernel.h> -#include <linux/netdevice.h> -#include <linux/interrupt.h> -#include <net/dst.h> - -#include "octeon-ethernet.h" -#include "ethernet-defines.h" -#include "ethernet-util.h" - -static int number_spi_ports; -static int need_retrain[2] = { 0, 0 }; - -static void cvm_oct_spxx_int_pr(union cvmx_spxx_int_reg spx_int_reg, int index) -{ - if (spx_int_reg.s.spf) - pr_err("SPI%d: SRX Spi4 interface down\n", index); - if (spx_int_reg.s.calerr) - pr_err("SPI%d: SRX Spi4 Calendar table parity error\n", index); - if (spx_int_reg.s.syncerr) - pr_err("SPI%d: SRX Consecutive Spi4 DIP4 errors have exceeded SPX_ERR_CTL[ERRCNT]\n", - index); - if (spx_int_reg.s.diperr) - pr_err("SPI%d: SRX Spi4 DIP4 error\n", index); - if (spx_int_reg.s.tpaovr) - pr_err("SPI%d: SRX Selected port has hit TPA overflow\n", - index); - if (spx_int_reg.s.rsverr) - pr_err("SPI%d: SRX Spi4 reserved control word detected\n", - index); - if (spx_int_reg.s.drwnng) - pr_err("SPI%d: SRX Spi4 receive FIFO drowning/overflow\n", - index); - if (spx_int_reg.s.clserr) - pr_err("SPI%d: SRX Spi4 packet closed on non-16B alignment without EOP\n", - index); - if (spx_int_reg.s.spiovr) - pr_err("SPI%d: SRX Spi4 async FIFO overflow\n", index); - if (spx_int_reg.s.abnorm) - pr_err("SPI%d: SRX Abnormal packet termination (ERR bit)\n", - index); - if (spx_int_reg.s.prtnxa) - pr_err("SPI%d: SRX Port out of range\n", index); -} - -static void cvm_oct_stxx_int_pr(union cvmx_stxx_int_reg stx_int_reg, int index) -{ - if (stx_int_reg.s.syncerr) - pr_err("SPI%d: STX Interface encountered a fatal error\n", - index); - if (stx_int_reg.s.frmerr) - pr_err("SPI%d: STX FRMCNT has exceeded STX_DIP_CNT[MAXFRM]\n", - index); - if (stx_int_reg.s.unxfrm) - pr_err("SPI%d: STX Unexpected framing sequence\n", index); - if (stx_int_reg.s.nosync) - pr_err("SPI%d: STX ERRCNT has exceeded STX_DIP_CNT[MAXDIP]\n", - index); - if (stx_int_reg.s.diperr) - pr_err("SPI%d: STX DIP2 error on the Spi4 Status channel\n", - index); - if (stx_int_reg.s.datovr) - pr_err("SPI%d: STX Spi4 FIFO overflow error\n", index); - if (stx_int_reg.s.ovrbst) - pr_err("SPI%d: STX Transmit packet burst too big\n", index); - if (stx_int_reg.s.calpar1) - pr_err("SPI%d: STX Calendar Table Parity Error Bank%d\n", - index, 1); - if (stx_int_reg.s.calpar0) - pr_err("SPI%d: STX Calendar Table Parity Error Bank%d\n", - index, 0); -} - -static irqreturn_t cvm_oct_spi_spx_int(int index) -{ - union cvmx_spxx_int_reg spx_int_reg; - union cvmx_stxx_int_reg stx_int_reg; - - spx_int_reg.u64 = cvmx_read_csr(CVMX_SPXX_INT_REG(index)); - cvmx_write_csr(CVMX_SPXX_INT_REG(index), spx_int_reg.u64); - if (!need_retrain[index]) { - spx_int_reg.u64 &= cvmx_read_csr(CVMX_SPXX_INT_MSK(index)); - cvm_oct_spxx_int_pr(spx_int_reg, index); - } - - stx_int_reg.u64 = cvmx_read_csr(CVMX_STXX_INT_REG(index)); - cvmx_write_csr(CVMX_STXX_INT_REG(index), stx_int_reg.u64); - if (!need_retrain[index]) { - stx_int_reg.u64 &= cvmx_read_csr(CVMX_STXX_INT_MSK(index)); - cvm_oct_stxx_int_pr(stx_int_reg, index); - } - - cvmx_write_csr(CVMX_SPXX_INT_MSK(index), 0); - cvmx_write_csr(CVMX_STXX_INT_MSK(index), 0); - need_retrain[index] = 1; - - return IRQ_HANDLED; -} - -static irqreturn_t cvm_oct_spi_rml_interrupt(int cpl, void *dev_id) -{ - irqreturn_t return_status = IRQ_NONE; - union cvmx_npi_rsl_int_blocks rsl_int_blocks; - - /* Check and see if this interrupt was caused by the GMX block */ - rsl_int_blocks.u64 = cvmx_read_csr(CVMX_NPI_RSL_INT_BLOCKS); - if (rsl_int_blocks.s.spx1) /* 19 - SPX1_INT_REG & STX1_INT_REG */ - return_status = cvm_oct_spi_spx_int(1); - - if (rsl_int_blocks.s.spx0) /* 18 - SPX0_INT_REG & STX0_INT_REG */ - return_status = cvm_oct_spi_spx_int(0); - - return return_status; -} - -static void cvm_oct_spi_enable_error_reporting(int interface) -{ - union cvmx_spxx_int_msk spxx_int_msk; - union cvmx_stxx_int_msk stxx_int_msk; - - spxx_int_msk.u64 = cvmx_read_csr(CVMX_SPXX_INT_MSK(interface)); - spxx_int_msk.s.calerr = 1; - spxx_int_msk.s.syncerr = 1; - spxx_int_msk.s.diperr = 1; - spxx_int_msk.s.tpaovr = 1; - spxx_int_msk.s.rsverr = 1; - spxx_int_msk.s.drwnng = 1; - spxx_int_msk.s.clserr = 1; - spxx_int_msk.s.spiovr = 1; - spxx_int_msk.s.abnorm = 1; - spxx_int_msk.s.prtnxa = 1; - cvmx_write_csr(CVMX_SPXX_INT_MSK(interface), spxx_int_msk.u64); - - stxx_int_msk.u64 = cvmx_read_csr(CVMX_STXX_INT_MSK(interface)); - stxx_int_msk.s.frmerr = 1; - stxx_int_msk.s.unxfrm = 1; - stxx_int_msk.s.nosync = 1; - stxx_int_msk.s.diperr = 1; - stxx_int_msk.s.datovr = 1; - stxx_int_msk.s.ovrbst = 1; - stxx_int_msk.s.calpar1 = 1; - stxx_int_msk.s.calpar0 = 1; - cvmx_write_csr(CVMX_STXX_INT_MSK(interface), stxx_int_msk.u64); -} - -static void cvm_oct_spi_poll(struct net_device *dev) -{ - static int spi4000_port; - struct octeon_ethernet *priv = netdev_priv(dev); - int interface; - - for (interface = 0; interface < 2; interface++) { - if ((priv->port == interface * 16) && need_retrain[interface]) { - if (cvmx_spi_restart_interface - (interface, CVMX_SPI_MODE_DUPLEX, 10) == 0) { - need_retrain[interface] = 0; - cvm_oct_spi_enable_error_reporting(interface); - } - } - - /* - * The SPI4000 TWSI interface is very slow. In order - * not to bring the system to a crawl, we only poll a - * single port every second. This means negotiation - * speed changes take up to 10 seconds, but at least - * we don't waste absurd amounts of time waiting for - * TWSI. - */ - if (priv->port == spi4000_port) { - /* - * This function does nothing if it is called on an - * interface without a SPI4000. - */ - cvmx_spi4000_check_speed(interface, priv->port); - /* - * Normal ordering increments. By decrementing - * we only match once per iteration. - */ - spi4000_port--; - if (spi4000_port < 0) - spi4000_port = 10; - } - } -} - -int cvm_oct_spi_init(struct net_device *dev) -{ - int r; - struct octeon_ethernet *priv = netdev_priv(dev); - - if (number_spi_ports == 0) { - r = request_irq(OCTEON_IRQ_RML, cvm_oct_spi_rml_interrupt, - IRQF_SHARED, "SPI", &number_spi_ports); - if (r) - return r; - } - number_spi_ports++; - - if ((priv->port == 0) || (priv->port == 16)) { - cvm_oct_spi_enable_error_reporting(INTERFACE(priv->port)); - priv->poll = cvm_oct_spi_poll; - } - cvm_oct_common_init(dev); - return 0; -} - -void cvm_oct_spi_uninit(struct net_device *dev) -{ - int interface; - - cvm_oct_common_uninit(dev); - number_spi_ports--; - if (number_spi_ports == 0) { - for (interface = 0; interface < 2; interface++) { - cvmx_write_csr(CVMX_SPXX_INT_MSK(interface), 0); - cvmx_write_csr(CVMX_STXX_INT_MSK(interface), 0); - } - free_irq(OCTEON_IRQ_RML, &number_spi_ports); - } -} diff --git a/drivers/staging/octeon/ethernet-tx.c b/drivers/staging/octeon/ethernet-tx.c deleted file mode 100644 index b334cf89794e..000000000000 --- a/drivers/staging/octeon/ethernet-tx.c +++ /dev/null @@ -1,717 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * This file is based on code from OCTEON SDK by Cavium Networks. - * - * Copyright (c) 2003-2010 Cavium Networks - */ - -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/netdevice.h> -#include <linux/etherdevice.h> -#include <linux/ip.h> -#include <linux/ratelimit.h> -#include <linux/string.h> -#include <linux/interrupt.h> -#include <net/dst.h> -#ifdef CONFIG_XFRM -#include <linux/xfrm.h> -#include <net/xfrm.h> -#endif /* CONFIG_XFRM */ - -#include <linux/atomic.h> -#include <net/sch_generic.h> - -#include "octeon-ethernet.h" -#include "ethernet-defines.h" -#include "ethernet-tx.h" -#include "ethernet-util.h" - -#define CVM_OCT_SKB_CB(skb) ((u64 *)((skb)->cb)) - -/* - * You can define GET_SKBUFF_QOS() to override how the skbuff output - * function determines which output queue is used. The default - * implementation always uses the base queue for the port. If, for - * example, you wanted to use the skb->priority field, define - * GET_SKBUFF_QOS as: #define GET_SKBUFF_QOS(skb) ((skb)->priority) - */ -#ifndef GET_SKBUFF_QOS -#define GET_SKBUFF_QOS(skb) 0 -#endif - -static void cvm_oct_tx_do_cleanup(unsigned long arg); -static DECLARE_TASKLET(cvm_oct_tx_cleanup_tasklet, cvm_oct_tx_do_cleanup, 0); - -/* Maximum number of SKBs to try to free per xmit packet. */ -#define MAX_SKB_TO_FREE (MAX_OUT_QUEUE_DEPTH * 2) - -static inline int cvm_oct_adjust_skb_to_free(int skb_to_free, int fau) -{ - int undo; - - undo = skb_to_free > 0 ? MAX_SKB_TO_FREE : skb_to_free + - MAX_SKB_TO_FREE; - if (undo > 0) - cvmx_fau_atomic_add32(fau, -undo); - skb_to_free = -skb_to_free > MAX_SKB_TO_FREE ? MAX_SKB_TO_FREE : - -skb_to_free; - return skb_to_free; -} - -static void cvm_oct_kick_tx_poll_watchdog(void) -{ - union cvmx_ciu_timx ciu_timx; - - ciu_timx.u64 = 0; - ciu_timx.s.one_shot = 1; - ciu_timx.s.len = cvm_oct_tx_poll_interval; - cvmx_write_csr(CVMX_CIU_TIMX(1), ciu_timx.u64); -} - -static void cvm_oct_free_tx_skbs(struct net_device *dev) -{ - int skb_to_free; - int qos, queues_per_port; - int total_freed = 0; - int total_remaining = 0; - unsigned long flags; - struct octeon_ethernet *priv = netdev_priv(dev); - - queues_per_port = cvmx_pko_get_num_queues(priv->port); - /* Drain any pending packets in the free list */ - for (qos = 0; qos < queues_per_port; qos++) { - if (skb_queue_len(&priv->tx_free_list[qos]) == 0) - continue; - skb_to_free = cvmx_fau_fetch_and_add32(priv->fau + qos * 4, - MAX_SKB_TO_FREE); - skb_to_free = cvm_oct_adjust_skb_to_free(skb_to_free, - priv->fau + qos * 4); - total_freed += skb_to_free; - if (skb_to_free > 0) { - struct sk_buff *to_free_list = NULL; - - spin_lock_irqsave(&priv->tx_free_list[qos].lock, flags); - while (skb_to_free > 0) { - struct sk_buff *t; - - t = __skb_dequeue(&priv->tx_free_list[qos]); - t->next = to_free_list; - to_free_list = t; - skb_to_free--; - } - spin_unlock_irqrestore(&priv->tx_free_list[qos].lock, - flags); - /* Do the actual freeing outside of the lock. */ - while (to_free_list) { - struct sk_buff *t = to_free_list; - - to_free_list = to_free_list->next; - dev_kfree_skb_any(t); - } - } - total_remaining += skb_queue_len(&priv->tx_free_list[qos]); - } - if (total_remaining < MAX_OUT_QUEUE_DEPTH && netif_queue_stopped(dev)) - netif_wake_queue(dev); - if (total_remaining) - cvm_oct_kick_tx_poll_watchdog(); -} - -/** - * cvm_oct_xmit - transmit a packet - * @skb: Packet to send - * @dev: Device info structure - * - * Returns Always returns NETDEV_TX_OK - */ -int cvm_oct_xmit(struct sk_buff *skb, struct net_device *dev) -{ - union cvmx_pko_command_word0 pko_command; - union cvmx_buf_ptr hw_buffer; - u64 old_scratch; - u64 old_scratch2; - int qos; - int i; - enum {QUEUE_CORE, QUEUE_HW, QUEUE_DROP} queue_type; - struct octeon_ethernet *priv = netdev_priv(dev); - struct sk_buff *to_free_list; - int skb_to_free; - int buffers_to_free; - u32 total_to_clean; - unsigned long flags; -#if REUSE_SKBUFFS_WITHOUT_FREE - unsigned char *fpa_head; -#endif - - /* - * Prefetch the private data structure. It is larger than the - * one cache line. - */ - prefetch(priv); - - /* - * The check on CVMX_PKO_QUEUES_PER_PORT_* is designed to - * completely remove "qos" in the event neither interface - * supports multiple queues per port. - */ - if ((CVMX_PKO_QUEUES_PER_PORT_INTERFACE0 > 1) || - (CVMX_PKO_QUEUES_PER_PORT_INTERFACE1 > 1)) { - qos = GET_SKBUFF_QOS(skb); - if (qos <= 0) - qos = 0; - else if (qos >= cvmx_pko_get_num_queues(priv->port)) - qos = 0; - } else { - qos = 0; - } - - if (USE_ASYNC_IOBDMA) { - /* Save scratch in case userspace is using it */ - CVMX_SYNCIOBDMA; - old_scratch = cvmx_scratch_read64(CVMX_SCR_SCRATCH); - old_scratch2 = cvmx_scratch_read64(CVMX_SCR_SCRATCH + 8); - - /* - * Fetch and increment the number of packets to be - * freed. - */ - cvmx_fau_async_fetch_and_add32(CVMX_SCR_SCRATCH + 8, - FAU_NUM_PACKET_BUFFERS_TO_FREE, - 0); - cvmx_fau_async_fetch_and_add32(CVMX_SCR_SCRATCH, - priv->fau + qos * 4, - MAX_SKB_TO_FREE); - } - - /* - * We have space for 6 segment pointers, If there will be more - * than that, we must linearize. - */ - if (unlikely(skb_shinfo(skb)->nr_frags > 5)) { - if (unlikely(__skb_linearize(skb))) { - queue_type = QUEUE_DROP; - if (USE_ASYNC_IOBDMA) { - /* - * Get the number of skbuffs in use - * by the hardware - */ - CVMX_SYNCIOBDMA; - skb_to_free = - cvmx_scratch_read64(CVMX_SCR_SCRATCH); - } else { - /* - * Get the number of skbuffs in use - * by the hardware - */ - skb_to_free = - cvmx_fau_fetch_and_add32(priv->fau + - qos * 4, - MAX_SKB_TO_FREE); - } - skb_to_free = cvm_oct_adjust_skb_to_free(skb_to_free, - priv->fau + - qos * 4); - spin_lock_irqsave(&priv->tx_free_list[qos].lock, flags); - goto skip_xmit; - } - } - - /* - * The CN3XXX series of parts has an errata (GMX-401) which - * causes the GMX block to hang if a collision occurs towards - * the end of a <68 byte packet. As a workaround for this, we - * pad packets to be 68 bytes whenever we are in half duplex - * mode. We don't handle the case of having a small packet but - * no room to add the padding. The kernel should always give - * us at least a cache line - */ - if ((skb->len < 64) && OCTEON_IS_MODEL(OCTEON_CN3XXX)) { - union cvmx_gmxx_prtx_cfg gmx_prt_cfg; - int interface = INTERFACE(priv->port); - int index = INDEX(priv->port); - - if (interface < 2) { - /* We only need to pad packet in half duplex mode */ - gmx_prt_cfg.u64 = - cvmx_read_csr(CVMX_GMXX_PRTX_CFG(index, interface)); - if (gmx_prt_cfg.s.duplex == 0) { - int add_bytes = 64 - skb->len; - - if ((skb_tail_pointer(skb) + add_bytes) <= - skb_end_pointer(skb)) - __skb_put_zero(skb, add_bytes); - } - } - } - - /* Build the PKO command */ - pko_command.u64 = 0; -#ifdef __LITTLE_ENDIAN - pko_command.s.le = 1; -#endif - pko_command.s.n2 = 1; /* Don't pollute L2 with the outgoing packet */ - pko_command.s.segs = 1; - pko_command.s.total_bytes = skb->len; - pko_command.s.size0 = CVMX_FAU_OP_SIZE_32; - pko_command.s.subone0 = 1; - - pko_command.s.dontfree = 1; - - /* Build the PKO buffer pointer */ - hw_buffer.u64 = 0; - if (skb_shinfo(skb)->nr_frags == 0) { - hw_buffer.s.addr = XKPHYS_TO_PHYS((uintptr_t)skb->data); - hw_buffer.s.pool = 0; - hw_buffer.s.size = skb->len; - } else { - hw_buffer.s.addr = XKPHYS_TO_PHYS((uintptr_t)skb->data); - hw_buffer.s.pool = 0; - hw_buffer.s.size = skb_headlen(skb); - CVM_OCT_SKB_CB(skb)[0] = hw_buffer.u64; - for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) { - skb_frag_t *fs = skb_shinfo(skb)->frags + i; - - hw_buffer.s.addr = - XKPHYS_TO_PHYS((uintptr_t)skb_frag_address(fs)); - hw_buffer.s.size = skb_frag_size(fs); - CVM_OCT_SKB_CB(skb)[i + 1] = hw_buffer.u64; - } - hw_buffer.s.addr = - XKPHYS_TO_PHYS((uintptr_t)CVM_OCT_SKB_CB(skb)); - hw_buffer.s.size = skb_shinfo(skb)->nr_frags + 1; - pko_command.s.segs = skb_shinfo(skb)->nr_frags + 1; - pko_command.s.gather = 1; - goto dont_put_skbuff_in_hw; - } - - /* - * See if we can put this skb in the FPA pool. Any strange - * behavior from the Linux networking stack will most likely - * be caused by a bug in the following code. If some field is - * in use by the network stack and gets carried over when a - * buffer is reused, bad things may happen. If in doubt and - * you dont need the absolute best performance, disable the - * define REUSE_SKBUFFS_WITHOUT_FREE. The reuse of buffers has - * shown a 25% increase in performance under some loads. - */ -#if REUSE_SKBUFFS_WITHOUT_FREE - fpa_head = skb->head + 256 - ((unsigned long)skb->head & 0x7f); - if (unlikely(skb->data < fpa_head)) { - /* TX buffer beginning can't meet FPA alignment constraints */ - goto dont_put_skbuff_in_hw; - } - if (unlikely - ((skb_end_pointer(skb) - fpa_head) < CVMX_FPA_PACKET_POOL_SIZE)) { - /* TX buffer isn't large enough for the FPA */ - goto dont_put_skbuff_in_hw; - } - if (unlikely(skb_shared(skb))) { - /* TX buffer sharing data with someone else */ - goto dont_put_skbuff_in_hw; - } - if (unlikely(skb_cloned(skb))) { - /* TX buffer has been cloned */ - goto dont_put_skbuff_in_hw; - } - if (unlikely(skb_header_cloned(skb))) { - /* TX buffer header has been cloned */ - goto dont_put_skbuff_in_hw; - } - if (unlikely(skb->destructor)) { - /* TX buffer has a destructor */ - goto dont_put_skbuff_in_hw; - } - if (unlikely(skb_shinfo(skb)->nr_frags)) { - /* TX buffer has fragments */ - goto dont_put_skbuff_in_hw; - } - if (unlikely - (skb->truesize != - sizeof(*skb) + skb_end_offset(skb))) { - /* TX buffer truesize has been changed */ - goto dont_put_skbuff_in_hw; - } - - /* - * We can use this buffer in the FPA. We don't need the FAU - * update anymore - */ - pko_command.s.dontfree = 0; - - hw_buffer.s.back = ((unsigned long)skb->data >> 7) - - ((unsigned long)fpa_head >> 7); - - *(struct sk_buff **)(fpa_head - sizeof(void *)) = skb; - - /* - * The skbuff will be reused without ever being freed. We must - * cleanup a bunch of core things. - */ - dst_release(skb_dst(skb)); - skb_dst_set(skb, NULL); - skb_ext_reset(skb); - nf_reset_ct(skb); - -#ifdef CONFIG_NET_SCHED - skb->tc_index = 0; - skb_reset_tc(skb); -#endif /* CONFIG_NET_SCHED */ -#endif /* REUSE_SKBUFFS_WITHOUT_FREE */ - -dont_put_skbuff_in_hw: - - /* Check if we can use the hardware checksumming */ - if ((skb->protocol == htons(ETH_P_IP)) && - (ip_hdr(skb)->version == 4) && - (ip_hdr(skb)->ihl == 5) && - ((ip_hdr(skb)->frag_off == 0) || - (ip_hdr(skb)->frag_off == htons(1 << 14))) && - ((ip_hdr(skb)->protocol == IPPROTO_TCP) || - (ip_hdr(skb)->protocol == IPPROTO_UDP))) { - /* Use hardware checksum calc */ - pko_command.s.ipoffp1 = skb_network_offset(skb) + 1; - } - - if (USE_ASYNC_IOBDMA) { - /* Get the number of skbuffs in use by the hardware */ - CVMX_SYNCIOBDMA; - skb_to_free = cvmx_scratch_read64(CVMX_SCR_SCRATCH); - buffers_to_free = cvmx_scratch_read64(CVMX_SCR_SCRATCH + 8); - } else { - /* Get the number of skbuffs in use by the hardware */ - skb_to_free = cvmx_fau_fetch_and_add32(priv->fau + qos * 4, - MAX_SKB_TO_FREE); - buffers_to_free = - cvmx_fau_fetch_and_add32(FAU_NUM_PACKET_BUFFERS_TO_FREE, 0); - } - - skb_to_free = cvm_oct_adjust_skb_to_free(skb_to_free, - priv->fau + qos * 4); - - /* - * If we're sending faster than the receive can free them then - * don't do the HW free. - */ - if ((buffers_to_free < -100) && !pko_command.s.dontfree) - pko_command.s.dontfree = 1; - - if (pko_command.s.dontfree) { - queue_type = QUEUE_CORE; - pko_command.s.reg0 = priv->fau + qos * 4; - } else { - queue_type = QUEUE_HW; - } - if (USE_ASYNC_IOBDMA) - cvmx_fau_async_fetch_and_add32(CVMX_SCR_SCRATCH, - FAU_TOTAL_TX_TO_CLEAN, 1); - - spin_lock_irqsave(&priv->tx_free_list[qos].lock, flags); - - /* Drop this packet if we have too many already queued to the HW */ - if (unlikely(skb_queue_len(&priv->tx_free_list[qos]) >= - MAX_OUT_QUEUE_DEPTH)) { - if (dev->tx_queue_len != 0) { - /* Drop the lock when notifying the core. */ - spin_unlock_irqrestore(&priv->tx_free_list[qos].lock, - flags); - netif_stop_queue(dev); - spin_lock_irqsave(&priv->tx_free_list[qos].lock, - flags); - } else { - /* If not using normal queueing. */ - queue_type = QUEUE_DROP; - goto skip_xmit; - } - } - - cvmx_pko_send_packet_prepare(priv->port, priv->queue + qos, - CVMX_PKO_LOCK_NONE); - - /* Send the packet to the output queue */ - if (unlikely(cvmx_pko_send_packet_finish(priv->port, - priv->queue + qos, - pko_command, hw_buffer, - CVMX_PKO_LOCK_NONE))) { - printk_ratelimited("%s: Failed to send the packet\n", - dev->name); - queue_type = QUEUE_DROP; - } -skip_xmit: - to_free_list = NULL; - - switch (queue_type) { - case QUEUE_DROP: - skb->next = to_free_list; - to_free_list = skb; - dev->stats.tx_dropped++; - break; - case QUEUE_HW: - cvmx_fau_atomic_add32(FAU_NUM_PACKET_BUFFERS_TO_FREE, -1); - break; - case QUEUE_CORE: - __skb_queue_tail(&priv->tx_free_list[qos], skb); - break; - default: - BUG(); - } - - while (skb_to_free > 0) { - struct sk_buff *t = __skb_dequeue(&priv->tx_free_list[qos]); - - t->next = to_free_list; - to_free_list = t; - skb_to_free--; - } - - spin_unlock_irqrestore(&priv->tx_free_list[qos].lock, flags); - - /* Do the actual freeing outside of the lock. */ - while (to_free_list) { - struct sk_buff *t = to_free_list; - - to_free_list = to_free_list->next; - dev_kfree_skb_any(t); - } - - if (USE_ASYNC_IOBDMA) { - CVMX_SYNCIOBDMA; - total_to_clean = cvmx_scratch_read64(CVMX_SCR_SCRATCH); - /* Restore the scratch area */ - cvmx_scratch_write64(CVMX_SCR_SCRATCH, old_scratch); - cvmx_scratch_write64(CVMX_SCR_SCRATCH + 8, old_scratch2); - } else { - total_to_clean = - cvmx_fau_fetch_and_add32(FAU_TOTAL_TX_TO_CLEAN, 1); - } - - if (total_to_clean & 0x3ff) { - /* - * Schedule the cleanup tasklet every 1024 packets for - * the pathological case of high traffic on one port - * delaying clean up of packets on a different port - * that is blocked waiting for the cleanup. - */ - tasklet_schedule(&cvm_oct_tx_cleanup_tasklet); - } - - cvm_oct_kick_tx_poll_watchdog(); - - return NETDEV_TX_OK; -} - -/** - * cvm_oct_xmit_pow - transmit a packet to the POW - * @skb: Packet to send - * @dev: Device info structure - - * Returns Always returns zero - */ -int cvm_oct_xmit_pow(struct sk_buff *skb, struct net_device *dev) -{ - struct octeon_ethernet *priv = netdev_priv(dev); - void *packet_buffer; - void *copy_location; - - /* Get a work queue entry */ - struct cvmx_wqe *work = cvmx_fpa_alloc(CVMX_FPA_WQE_POOL); - - if (unlikely(!work)) { - printk_ratelimited("%s: Failed to allocate a work queue entry\n", - dev->name); - dev->stats.tx_dropped++; - dev_kfree_skb_any(skb); - return 0; - } - - /* Get a packet buffer */ - packet_buffer = cvmx_fpa_alloc(CVMX_FPA_PACKET_POOL); - if (unlikely(!packet_buffer)) { - printk_ratelimited("%s: Failed to allocate a packet buffer\n", - dev->name); - cvmx_fpa_free(work, CVMX_FPA_WQE_POOL, 1); - dev->stats.tx_dropped++; - dev_kfree_skb_any(skb); - return 0; - } - - /* - * Calculate where we need to copy the data to. We need to - * leave 8 bytes for a next pointer (unused). We also need to - * include any configure skip. Then we need to align the IP - * packet src and dest into the same 64bit word. The below - * calculation may add a little extra, but that doesn't - * hurt. - */ - copy_location = packet_buffer + sizeof(u64); - copy_location += ((CVMX_HELPER_FIRST_MBUFF_SKIP + 7) & 0xfff8) + 6; - - /* - * We have to copy the packet since whoever processes this - * packet will free it to a hardware pool. We can't use the - * trick of counting outstanding packets like in - * cvm_oct_xmit. - */ - memcpy(copy_location, skb->data, skb->len); - - /* - * Fill in some of the work queue fields. We may need to add - * more if the software at the other end needs them. - */ - if (!OCTEON_IS_MODEL(OCTEON_CN68XX)) - work->word0.pip.cn38xx.hw_chksum = skb->csum; - work->word1.len = skb->len; - cvmx_wqe_set_port(work, priv->port); - cvmx_wqe_set_qos(work, priv->port & 0x7); - cvmx_wqe_set_grp(work, pow_send_group); - work->word1.tag_type = CVMX_HELPER_INPUT_TAG_TYPE; - work->word1.tag = pow_send_group; /* FIXME */ - /* Default to zero. Sets of zero later are commented out */ - work->word2.u64 = 0; - work->word2.s.bufs = 1; - work->packet_ptr.u64 = 0; - work->packet_ptr.s.addr = cvmx_ptr_to_phys(copy_location); - work->packet_ptr.s.pool = CVMX_FPA_PACKET_POOL; - work->packet_ptr.s.size = CVMX_FPA_PACKET_POOL_SIZE; - work->packet_ptr.s.back = (copy_location - packet_buffer) >> 7; - - if (skb->protocol == htons(ETH_P_IP)) { - work->word2.s.ip_offset = 14; -#if 0 - work->word2.s.vlan_valid = 0; /* FIXME */ - work->word2.s.vlan_cfi = 0; /* FIXME */ - work->word2.s.vlan_id = 0; /* FIXME */ - work->word2.s.dec_ipcomp = 0; /* FIXME */ -#endif - work->word2.s.tcp_or_udp = - (ip_hdr(skb)->protocol == IPPROTO_TCP) || - (ip_hdr(skb)->protocol == IPPROTO_UDP); -#if 0 - /* FIXME */ - work->word2.s.dec_ipsec = 0; - /* We only support IPv4 right now */ - work->word2.s.is_v6 = 0; - /* Hardware would set to zero */ - work->word2.s.software = 0; - /* No error, packet is internal */ - work->word2.s.L4_error = 0; -#endif - work->word2.s.is_frag = !((ip_hdr(skb)->frag_off == 0) || - (ip_hdr(skb)->frag_off == - cpu_to_be16(1 << 14))); -#if 0 - /* Assume Linux is sending a good packet */ - work->word2.s.IP_exc = 0; -#endif - work->word2.s.is_bcast = (skb->pkt_type == PACKET_BROADCAST); - work->word2.s.is_mcast = (skb->pkt_type == PACKET_MULTICAST); -#if 0 - /* This is an IP packet */ - work->word2.s.not_IP = 0; - /* No error, packet is internal */ - work->word2.s.rcv_error = 0; - /* No error, packet is internal */ - work->word2.s.err_code = 0; -#endif - - /* - * When copying the data, include 4 bytes of the - * ethernet header to align the same way hardware - * does. - */ - memcpy(work->packet_data, skb->data + 10, - sizeof(work->packet_data)); - } else { -#if 0 - work->word2.snoip.vlan_valid = 0; /* FIXME */ - work->word2.snoip.vlan_cfi = 0; /* FIXME */ - work->word2.snoip.vlan_id = 0; /* FIXME */ - work->word2.snoip.software = 0; /* Hardware would set to zero */ -#endif - work->word2.snoip.is_rarp = skb->protocol == htons(ETH_P_RARP); - work->word2.snoip.is_arp = skb->protocol == htons(ETH_P_ARP); - work->word2.snoip.is_bcast = - (skb->pkt_type == PACKET_BROADCAST); - work->word2.snoip.is_mcast = - (skb->pkt_type == PACKET_MULTICAST); - work->word2.snoip.not_IP = 1; /* IP was done up above */ -#if 0 - /* No error, packet is internal */ - work->word2.snoip.rcv_error = 0; - /* No error, packet is internal */ - work->word2.snoip.err_code = 0; -#endif - memcpy(work->packet_data, skb->data, sizeof(work->packet_data)); - } - - /* Submit the packet to the POW */ - cvmx_pow_work_submit(work, work->word1.tag, work->word1.tag_type, - cvmx_wqe_get_qos(work), cvmx_wqe_get_grp(work)); - dev->stats.tx_packets++; - dev->stats.tx_bytes += skb->len; - dev_consume_skb_any(skb); - return 0; -} - -/** - * cvm_oct_tx_shutdown_dev - free all skb that are currently queued for TX. - * @dev: Device being shutdown - * - */ -void cvm_oct_tx_shutdown_dev(struct net_device *dev) -{ - struct octeon_ethernet *priv = netdev_priv(dev); - unsigned long flags; - int qos; - - for (qos = 0; qos < 16; qos++) { - spin_lock_irqsave(&priv->tx_free_list[qos].lock, flags); - while (skb_queue_len(&priv->tx_free_list[qos])) - dev_kfree_skb_any(__skb_dequeue - (&priv->tx_free_list[qos])); - spin_unlock_irqrestore(&priv->tx_free_list[qos].lock, flags); - } -} - -static void cvm_oct_tx_do_cleanup(unsigned long arg) -{ - int port; - - for (port = 0; port < TOTAL_NUMBER_OF_PORTS; port++) { - if (cvm_oct_device[port]) { - struct net_device *dev = cvm_oct_device[port]; - - cvm_oct_free_tx_skbs(dev); - } - } -} - -static irqreturn_t cvm_oct_tx_cleanup_watchdog(int cpl, void *dev_id) -{ - /* Disable the interrupt. */ - cvmx_write_csr(CVMX_CIU_TIMX(1), 0); - /* Do the work in the tasklet. */ - tasklet_schedule(&cvm_oct_tx_cleanup_tasklet); - return IRQ_HANDLED; -} - -void cvm_oct_tx_initialize(void) -{ - int i; - - /* Disable the interrupt. */ - cvmx_write_csr(CVMX_CIU_TIMX(1), 0); - /* Register an IRQ handler to receive CIU_TIMX(1) interrupts */ - i = request_irq(OCTEON_IRQ_TIMER1, - cvm_oct_tx_cleanup_watchdog, 0, - "Ethernet", cvm_oct_device); - - if (i) - panic("Could not acquire Ethernet IRQ %d\n", OCTEON_IRQ_TIMER1); -} - -void cvm_oct_tx_shutdown(void) -{ - /* Free the interrupt handler */ - free_irq(OCTEON_IRQ_TIMER1, cvm_oct_device); -} diff --git a/drivers/staging/octeon/ethernet-tx.h b/drivers/staging/octeon/ethernet-tx.h deleted file mode 100644 index 78936e9b33b0..000000000000 --- a/drivers/staging/octeon/ethernet-tx.h +++ /dev/null @@ -1,14 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0 */ -/* - * This file is based on code from OCTEON SDK by Cavium Networks. - * - * Copyright (c) 2003-2007 Cavium Networks - */ - -int cvm_oct_xmit(struct sk_buff *skb, struct net_device *dev); -int cvm_oct_xmit_pow(struct sk_buff *skb, struct net_device *dev); -int cvm_oct_transmit_qos(struct net_device *dev, void *work_queue_entry, - int do_free, int qos); -void cvm_oct_tx_initialize(void); -void cvm_oct_tx_shutdown(void); -void cvm_oct_tx_shutdown_dev(struct net_device *dev); diff --git a/drivers/staging/octeon/ethernet-util.h b/drivers/staging/octeon/ethernet-util.h deleted file mode 100644 index 2af83a12ca78..000000000000 --- a/drivers/staging/octeon/ethernet-util.h +++ /dev/null @@ -1,47 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0 */ -/* - * This file is based on code from OCTEON SDK by Cavium Networks. - * - * Copyright (c) 2003-2007 Cavium Networks - */ - -/** - * cvm_oct_get_buffer_ptr - convert packet data address to pointer - * @packet_ptr: Packet data hardware address - * - * Returns Packet buffer pointer - */ -static inline void *cvm_oct_get_buffer_ptr(union cvmx_buf_ptr packet_ptr) -{ - return cvmx_phys_to_ptr(((packet_ptr.s.addr >> 7) - packet_ptr.s.back) - << 7); -} - -/** - * INTERFACE - convert IPD port to logical interface - * @ipd_port: Port to check - * - * Returns Logical interface - */ -static inline int INTERFACE(int ipd_port) -{ - int interface; - - if (ipd_port == CVMX_PIP_NUM_INPUT_PORTS) - return 10; - interface = cvmx_helper_get_interface_num(ipd_port); - if (interface >= 0) - return interface; - panic("Illegal ipd_port %d passed to %s\n", ipd_port, __func__); -} - -/** - * INDEX - convert IPD/PKO port number to the port's interface index - * @ipd_port: Port to check - * - * Returns Index into interface port list - */ -static inline int INDEX(int ipd_port) -{ - return cvmx_helper_get_interface_index_num(ipd_port); -} diff --git a/drivers/staging/octeon/ethernet.c b/drivers/staging/octeon/ethernet.c deleted file mode 100644 index f42c3816ce49..000000000000 --- a/drivers/staging/octeon/ethernet.c +++ /dev/null @@ -1,992 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * This file is based on code from OCTEON SDK by Cavium Networks. - * - * Copyright (c) 2003-2007 Cavium Networks - */ - -#include <linux/platform_device.h> -#include <linux/kernel.h> -#include <linux/module.h> -#include <linux/netdevice.h> -#include <linux/etherdevice.h> -#include <linux/phy.h> -#include <linux/slab.h> -#include <linux/interrupt.h> -#include <linux/of_net.h> -#include <linux/if_ether.h> -#include <linux/if_vlan.h> - -#include <net/dst.h> - -#include "octeon-ethernet.h" -#include "ethernet-defines.h" -#include "ethernet-mem.h" -#include "ethernet-rx.h" -#include "ethernet-tx.h" -#include "ethernet-mdio.h" -#include "ethernet-util.h" - -#define OCTEON_MAX_MTU 65392 - -static int num_packet_buffers = 1024; -module_param(num_packet_buffers, int, 0444); -MODULE_PARM_DESC(num_packet_buffers, "\n" - "\tNumber of packet buffers to allocate and store in the\n" - "\tFPA. By default, 1024 packet buffers are used.\n"); - -static int pow_receive_group = 15; -module_param(pow_receive_group, int, 0444); -MODULE_PARM_DESC(pow_receive_group, "\n" - "\tPOW group to receive packets from. All ethernet hardware\n" - "\twill be configured to send incoming packets to this POW\n" - "\tgroup. Also any other software can submit packets to this\n" - "\tgroup for the kernel to process."); - -static int receive_group_order; -module_param(receive_group_order, int, 0444); -MODULE_PARM_DESC(receive_group_order, "\n" - "\tOrder (0..4) of receive groups to take into use. Ethernet hardware\n" - "\twill be configured to send incoming packets to multiple POW\n" - "\tgroups. pow_receive_group parameter is ignored when multiple\n" - "\tgroups are taken into use and groups are allocated starting\n" - "\tfrom 0. By default, a single group is used.\n"); - -int pow_send_group = -1; -module_param(pow_send_group, int, 0644); -MODULE_PARM_DESC(pow_send_group, "\n" - "\tPOW group to send packets to other software on. This\n" - "\tcontrols the creation of the virtual device pow0.\n" - "\talways_use_pow also depends on this value."); - -int always_use_pow; -module_param(always_use_pow, int, 0444); -MODULE_PARM_DESC(always_use_pow, "\n" - "\tWhen set, always send to the pow group. This will cause\n" - "\tpackets sent to real ethernet devices to be sent to the\n" - "\tPOW group instead of the hardware. Unless some other\n" - "\tapplication changes the config, packets will still be\n" - "\treceived from the low level hardware. Use this option\n" - "\tto allow a CVMX app to intercept all packets from the\n" - "\tlinux kernel. You must specify pow_send_group along with\n" - "\tthis option."); - -char pow_send_list[128] = ""; -module_param_string(pow_send_list, pow_send_list, sizeof(pow_send_list), 0444); -MODULE_PARM_DESC(pow_send_list, "\n" - "\tComma separated list of ethernet devices that should use the\n" - "\tPOW for transmit instead of the actual ethernet hardware. This\n" - "\tis a per port version of always_use_pow. always_use_pow takes\n" - "\tprecedence over this list. For example, setting this to\n" - "\t\"eth2,spi3,spi7\" would cause these three devices to transmit\n" - "\tusing the pow_send_group."); - -int rx_napi_weight = 32; -module_param(rx_napi_weight, int, 0444); -MODULE_PARM_DESC(rx_napi_weight, "The NAPI WEIGHT parameter."); - -/* Mask indicating which receive groups are in use. */ -int pow_receive_groups; - -/* - * cvm_oct_poll_queue_stopping - flag to indicate polling should stop. - * - * Set to one right before cvm_oct_poll_queue is destroyed. - */ -atomic_t cvm_oct_poll_queue_stopping = ATOMIC_INIT(0); - -/* - * Array of every ethernet device owned by this driver indexed by - * the ipd input port number. - */ -struct net_device *cvm_oct_device[TOTAL_NUMBER_OF_PORTS]; - -u64 cvm_oct_tx_poll_interval; - -static void cvm_oct_rx_refill_worker(struct work_struct *work); -static DECLARE_DELAYED_WORK(cvm_oct_rx_refill_work, cvm_oct_rx_refill_worker); - -static void cvm_oct_rx_refill_worker(struct work_struct *work) -{ - /* - * FPA 0 may have been drained, try to refill it if we need - * more than num_packet_buffers / 2, otherwise normal receive - * processing will refill it. If it were drained, no packets - * could be received so cvm_oct_napi_poll would never be - * invoked to do the refill. - */ - cvm_oct_rx_refill_pool(num_packet_buffers / 2); - - if (!atomic_read(&cvm_oct_poll_queue_stopping)) - schedule_delayed_work(&cvm_oct_rx_refill_work, HZ); -} - -static void cvm_oct_periodic_worker(struct work_struct *work) -{ - struct octeon_ethernet *priv = container_of(work, - struct octeon_ethernet, - port_periodic_work.work); - - if (priv->poll) - priv->poll(cvm_oct_device[priv->port]); - - cvm_oct_device[priv->port]->netdev_ops->ndo_get_stats - (cvm_oct_device[priv->port]); - - if (!atomic_read(&cvm_oct_poll_queue_stopping)) - schedule_delayed_work(&priv->port_periodic_work, HZ); -} - -static void cvm_oct_configure_common_hw(void) -{ - /* Setup the FPA */ - cvmx_fpa_enable(); - cvm_oct_mem_fill_fpa(CVMX_FPA_PACKET_POOL, CVMX_FPA_PACKET_POOL_SIZE, - num_packet_buffers); - cvm_oct_mem_fill_fpa(CVMX_FPA_WQE_POOL, CVMX_FPA_WQE_POOL_SIZE, - num_packet_buffers); - if (CVMX_FPA_OUTPUT_BUFFER_POOL != CVMX_FPA_PACKET_POOL) - cvm_oct_mem_fill_fpa(CVMX_FPA_OUTPUT_BUFFER_POOL, - CVMX_FPA_OUTPUT_BUFFER_POOL_SIZE, 1024); - -#ifdef __LITTLE_ENDIAN - { - union cvmx_ipd_ctl_status ipd_ctl_status; - - ipd_ctl_status.u64 = cvmx_read_csr(CVMX_IPD_CTL_STATUS); - ipd_ctl_status.s.pkt_lend = 1; - ipd_ctl_status.s.wqe_lend = 1; - cvmx_write_csr(CVMX_IPD_CTL_STATUS, ipd_ctl_status.u64); - } -#endif - - cvmx_helper_setup_red(num_packet_buffers / 4, num_packet_buffers / 8); -} - -/** - * cvm_oct_free_work- Free a work queue entry - * - * @work_queue_entry: Work queue entry to free - * - * Returns Zero on success, Negative on failure. - */ -int cvm_oct_free_work(void *work_queue_entry) -{ - struct cvmx_wqe *work = work_queue_entry; - - int segments = work->word2.s.bufs; - union cvmx_buf_ptr segment_ptr = work->packet_ptr; - - while (segments--) { - union cvmx_buf_ptr next_ptr = *(union cvmx_buf_ptr *) - cvmx_phys_to_ptr(segment_ptr.s.addr - 8); - if (unlikely(!segment_ptr.s.i)) - cvmx_fpa_free(cvm_oct_get_buffer_ptr(segment_ptr), - segment_ptr.s.pool, - CVMX_FPA_PACKET_POOL_SIZE / 128); - segment_ptr = next_ptr; - } - cvmx_fpa_free(work, CVMX_FPA_WQE_POOL, 1); - - return 0; -} -EXPORT_SYMBOL(cvm_oct_free_work); - -/** - * cvm_oct_common_get_stats - get the low level ethernet statistics - * @dev: Device to get the statistics from - * - * Returns Pointer to the statistics - */ -static struct net_device_stats *cvm_oct_common_get_stats(struct net_device *dev) -{ - cvmx_pip_port_status_t rx_status; - cvmx_pko_port_status_t tx_status; - struct octeon_ethernet *priv = netdev_priv(dev); - - if (priv->port < CVMX_PIP_NUM_INPUT_PORTS) { - if (octeon_is_simulation()) { - /* The simulator doesn't support statistics */ - memset(&rx_status, 0, sizeof(rx_status)); - memset(&tx_status, 0, sizeof(tx_status)); - } else { - cvmx_pip_get_port_status(priv->port, 1, &rx_status); - cvmx_pko_get_port_status(priv->port, 1, &tx_status); - } - - dev->stats.rx_packets += rx_status.inb_packets; - dev->stats.tx_packets += tx_status.packets; - dev->stats.rx_bytes += rx_status.inb_octets; - dev->stats.tx_bytes += tx_status.octets; - dev->stats.multicast += rx_status.multicast_packets; - dev->stats.rx_crc_errors += rx_status.inb_errors; - dev->stats.rx_frame_errors += rx_status.fcs_align_err_packets; - dev->stats.rx_dropped += rx_status.dropped_packets; - } - - return &dev->stats; -} - -/** - * cvm_oct_common_change_mtu - change the link MTU - * @dev: Device to change - * @new_mtu: The new MTU - * - * Returns Zero on success - */ -static int cvm_oct_common_change_mtu(struct net_device *dev, int new_mtu) -{ - struct octeon_ethernet *priv = netdev_priv(dev); - int interface = INTERFACE(priv->port); -#if IS_ENABLED(CONFIG_VLAN_8021Q) - int vlan_bytes = VLAN_HLEN; -#else - int vlan_bytes = 0; -#endif - int mtu_overhead = ETH_HLEN + ETH_FCS_LEN + vlan_bytes; - - dev->mtu = new_mtu; - - if ((interface < 2) && - (cvmx_helper_interface_get_mode(interface) != - CVMX_HELPER_INTERFACE_MODE_SPI)) { - int index = INDEX(priv->port); - /* Add ethernet header and FCS, and VLAN if configured. */ - int max_packet = new_mtu + mtu_overhead; - - if (OCTEON_IS_MODEL(OCTEON_CN3XXX) || - OCTEON_IS_MODEL(OCTEON_CN58XX)) { - /* Signal errors on packets larger than the MTU */ - cvmx_write_csr(CVMX_GMXX_RXX_FRM_MAX(index, interface), - max_packet); - } else { - /* - * Set the hardware to truncate packets larger - * than the MTU and smaller the 64 bytes. - */ - union cvmx_pip_frm_len_chkx frm_len_chk; - - frm_len_chk.u64 = 0; - frm_len_chk.s.minlen = VLAN_ETH_ZLEN; - frm_len_chk.s.maxlen = max_packet; - cvmx_write_csr(CVMX_PIP_FRM_LEN_CHKX(interface), - frm_len_chk.u64); - } - /* - * Set the hardware to truncate packets larger than - * the MTU. The jabber register must be set to a - * multiple of 8 bytes, so round up. - */ - cvmx_write_csr(CVMX_GMXX_RXX_JABBER(index, interface), - (max_packet + 7) & ~7u); - } - return 0; -} - -/** - * cvm_oct_common_set_multicast_list - set the multicast list - * @dev: Device to work on - */ -static void cvm_oct_common_set_multicast_list(struct net_device *dev) -{ - union cvmx_gmxx_prtx_cfg gmx_cfg; - struct octeon_ethernet *priv = netdev_priv(dev); - int interface = INTERFACE(priv->port); - - if ((interface < 2) && - (cvmx_helper_interface_get_mode(interface) != - CVMX_HELPER_INTERFACE_MODE_SPI)) { - union cvmx_gmxx_rxx_adr_ctl control; - int index = INDEX(priv->port); - - control.u64 = 0; - control.s.bcst = 1; /* Allow broadcast MAC addresses */ - - if (!netdev_mc_empty(dev) || (dev->flags & IFF_ALLMULTI) || - (dev->flags & IFF_PROMISC)) - /* Force accept multicast packets */ - control.s.mcst = 2; - else - /* Force reject multicast packets */ - control.s.mcst = 1; - - if (dev->flags & IFF_PROMISC) - /* - * Reject matches if promisc. Since CAM is - * shut off, should accept everything. - */ - control.s.cam_mode = 0; - else - /* Filter packets based on the CAM */ - control.s.cam_mode = 1; - - gmx_cfg.u64 = - cvmx_read_csr(CVMX_GMXX_PRTX_CFG(index, interface)); - cvmx_write_csr(CVMX_GMXX_PRTX_CFG(index, interface), - gmx_cfg.u64 & ~1ull); - - cvmx_write_csr(CVMX_GMXX_RXX_ADR_CTL(index, interface), - control.u64); - if (dev->flags & IFF_PROMISC) - cvmx_write_csr(CVMX_GMXX_RXX_ADR_CAM_EN - (index, interface), 0); - else - cvmx_write_csr(CVMX_GMXX_RXX_ADR_CAM_EN - (index, interface), 1); - - cvmx_write_csr(CVMX_GMXX_PRTX_CFG(index, interface), - gmx_cfg.u64); - } -} - -static int cvm_oct_set_mac_filter(struct net_device *dev) -{ - struct octeon_ethernet *priv = netdev_priv(dev); - union cvmx_gmxx_prtx_cfg gmx_cfg; - int interface = INTERFACE(priv->port); - - if ((interface < 2) && - (cvmx_helper_interface_get_mode(interface) != - CVMX_HELPER_INTERFACE_MODE_SPI)) { - int i; - u8 *ptr = dev->dev_addr; - u64 mac = 0; - int index = INDEX(priv->port); - - for (i = 0; i < 6; i++) - mac = (mac << 8) | (u64)ptr[i]; - - gmx_cfg.u64 = - cvmx_read_csr(CVMX_GMXX_PRTX_CFG(index, interface)); - cvmx_write_csr(CVMX_GMXX_PRTX_CFG(index, interface), - gmx_cfg.u64 & ~1ull); - - cvmx_write_csr(CVMX_GMXX_SMACX(index, interface), mac); - cvmx_write_csr(CVMX_GMXX_RXX_ADR_CAM0(index, interface), - ptr[0]); - cvmx_write_csr(CVMX_GMXX_RXX_ADR_CAM1(index, interface), - ptr[1]); - cvmx_write_csr(CVMX_GMXX_RXX_ADR_CAM2(index, interface), - ptr[2]); - cvmx_write_csr(CVMX_GMXX_RXX_ADR_CAM3(index, interface), - ptr[3]); - cvmx_write_csr(CVMX_GMXX_RXX_ADR_CAM4(index, interface), - ptr[4]); - cvmx_write_csr(CVMX_GMXX_RXX_ADR_CAM5(index, interface), - ptr[5]); - cvm_oct_common_set_multicast_list(dev); - cvmx_write_csr(CVMX_GMXX_PRTX_CFG(index, interface), - gmx_cfg.u64); - } - return 0; -} - -/** - * cvm_oct_common_set_mac_address - set the hardware MAC address for a device - * @dev: The device in question. - * @addr: Socket address. - * - * Returns Zero on success - */ -static int cvm_oct_common_set_mac_address(struct net_device *dev, void *addr) -{ - int r = eth_mac_addr(dev, addr); - - if (r) - return r; - return cvm_oct_set_mac_filter(dev); -} - -/** - * cvm_oct_common_init - per network device initialization - * @dev: Device to initialize - * - * Returns Zero on success - */ -int cvm_oct_common_init(struct net_device *dev) -{ - struct octeon_ethernet *priv = netdev_priv(dev); - const u8 *mac = NULL; - - if (priv->of_node) - mac = of_get_mac_address(priv->of_node); - - if (!IS_ERR_OR_NULL(mac)) - ether_addr_copy(dev->dev_addr, mac); - else - eth_hw_addr_random(dev); - - /* - * Force the interface to use the POW send if always_use_pow - * was specified or it is in the pow send list. - */ - if ((pow_send_group != -1) && - (always_use_pow || strstr(pow_send_list, dev->name))) - priv->queue = -1; - - if (priv->queue != -1) - dev->features |= NETIF_F_SG | NETIF_F_IP_CSUM; - - /* We do our own locking, Linux doesn't need to */ - dev->features |= NETIF_F_LLTX; - dev->ethtool_ops = &cvm_oct_ethtool_ops; - - cvm_oct_set_mac_filter(dev); - dev_set_mtu(dev, dev->mtu); - - /* - * Zero out stats for port so we won't mistakenly show - * counters from the bootloader. - */ - memset(dev->netdev_ops->ndo_get_stats(dev), 0, - sizeof(struct net_device_stats)); - - if (dev->netdev_ops->ndo_stop) - dev->netdev_ops->ndo_stop(dev); - - return 0; -} - -void cvm_oct_common_uninit(struct net_device *dev) -{ - if (dev->phydev) - phy_disconnect(dev->phydev); -} - -int cvm_oct_common_open(struct net_device *dev, - void (*link_poll)(struct net_device *)) -{ - union cvmx_gmxx_prtx_cfg gmx_cfg; - struct octeon_ethernet *priv = netdev_priv(dev); - int interface = INTERFACE(priv->port); - int index = INDEX(priv->port); - union cvmx_helper_link_info link_info; - int rv; - - rv = cvm_oct_phy_setup_device(dev); - if (rv) - return rv; - - gmx_cfg.u64 = cvmx_read_csr(CVMX_GMXX_PRTX_CFG(index, interface)); - gmx_cfg.s.en = 1; - if (octeon_has_feature(OCTEON_FEATURE_PKND)) - gmx_cfg.s.pknd = priv->port; - cvmx_write_csr(CVMX_GMXX_PRTX_CFG(index, interface), gmx_cfg.u64); - - if (octeon_is_simulation()) - return 0; - - if (dev->phydev) { - int r = phy_read_status(dev->phydev); - - if (r == 0 && dev->phydev->link == 0) - netif_carrier_off(dev); - cvm_oct_adjust_link(dev); - } else { - link_info = cvmx_helper_link_get(priv->port); - if (!link_info.s.link_up) - netif_carrier_off(dev); - priv->poll = link_poll; - link_poll(dev); - } - - return 0; -} - -void cvm_oct_link_poll(struct net_device *dev) -{ - struct octeon_ethernet *priv = netdev_priv(dev); - union cvmx_helper_link_info link_info; - - link_info = cvmx_helper_link_get(priv->port); - if (link_info.u64 == priv->link_info) - return; - - if (cvmx_helper_link_set(priv->port, link_info)) - link_info.u64 = priv->link_info; - else - priv->link_info = link_info.u64; - - if (link_info.s.link_up) { - if (!netif_carrier_ok(dev)) - netif_carrier_on(dev); - } else if (netif_carrier_ok(dev)) { - netif_carrier_off(dev); - } - cvm_oct_note_carrier(priv, link_info); -} - -static int cvm_oct_xaui_open(struct net_device *dev) -{ - return cvm_oct_common_open(dev, cvm_oct_link_poll); -} - -static const struct net_device_ops cvm_oct_npi_netdev_ops = { - .ndo_init = cvm_oct_common_init, - .ndo_uninit = cvm_oct_common_uninit, - .ndo_start_xmit = cvm_oct_xmit, - .ndo_set_rx_mode = cvm_oct_common_set_multicast_list, - .ndo_set_mac_address = cvm_oct_common_set_mac_address, - .ndo_do_ioctl = cvm_oct_ioctl, - .ndo_change_mtu = cvm_oct_common_change_mtu, - .ndo_get_stats = cvm_oct_common_get_stats, -#ifdef CONFIG_NET_POLL_CONTROLLER - .ndo_poll_controller = cvm_oct_poll_controller, -#endif -}; - -static const struct net_device_ops cvm_oct_xaui_netdev_ops = { - .ndo_init = cvm_oct_common_init, - .ndo_uninit = cvm_oct_common_uninit, - .ndo_open = cvm_oct_xaui_open, - .ndo_stop = cvm_oct_common_stop, - .ndo_start_xmit = cvm_oct_xmit, - .ndo_set_rx_mode = cvm_oct_common_set_multicast_list, - .ndo_set_mac_address = cvm_oct_common_set_mac_address, - .ndo_do_ioctl = cvm_oct_ioctl, - .ndo_change_mtu = cvm_oct_common_change_mtu, - .ndo_get_stats = cvm_oct_common_get_stats, -#ifdef CONFIG_NET_POLL_CONTROLLER - .ndo_poll_controller = cvm_oct_poll_controller, -#endif -}; - -static const struct net_device_ops cvm_oct_sgmii_netdev_ops = { - .ndo_init = cvm_oct_sgmii_init, - .ndo_uninit = cvm_oct_common_uninit, - .ndo_open = cvm_oct_sgmii_open, - .ndo_stop = cvm_oct_common_stop, - .ndo_start_xmit = cvm_oct_xmit, - .ndo_set_rx_mode = cvm_oct_common_set_multicast_list, - .ndo_set_mac_address = cvm_oct_common_set_mac_address, - .ndo_do_ioctl = cvm_oct_ioctl, - .ndo_change_mtu = cvm_oct_common_change_mtu, - .ndo_get_stats = cvm_oct_common_get_stats, -#ifdef CONFIG_NET_POLL_CONTROLLER - .ndo_poll_controller = cvm_oct_poll_controller, -#endif -}; - -static const struct net_device_ops cvm_oct_spi_netdev_ops = { - .ndo_init = cvm_oct_spi_init, - .ndo_uninit = cvm_oct_spi_uninit, - .ndo_start_xmit = cvm_oct_xmit, - .ndo_set_rx_mode = cvm_oct_common_set_multicast_list, - .ndo_set_mac_address = cvm_oct_common_set_mac_address, - .ndo_do_ioctl = cvm_oct_ioctl, - .ndo_change_mtu = cvm_oct_common_change_mtu, - .ndo_get_stats = cvm_oct_common_get_stats, -#ifdef CONFIG_NET_POLL_CONTROLLER - .ndo_poll_controller = cvm_oct_poll_controller, -#endif -}; - -static const struct net_device_ops cvm_oct_rgmii_netdev_ops = { - .ndo_init = cvm_oct_common_init, - .ndo_uninit = cvm_oct_common_uninit, - .ndo_open = cvm_oct_rgmii_open, - .ndo_stop = cvm_oct_common_stop, - .ndo_start_xmit = cvm_oct_xmit, - .ndo_set_rx_mode = cvm_oct_common_set_multicast_list, - .ndo_set_mac_address = cvm_oct_common_set_mac_address, - .ndo_do_ioctl = cvm_oct_ioctl, - .ndo_change_mtu = cvm_oct_common_change_mtu, - .ndo_get_stats = cvm_oct_common_get_stats, -#ifdef CONFIG_NET_POLL_CONTROLLER - .ndo_poll_controller = cvm_oct_poll_controller, -#endif -}; - -static const struct net_device_ops cvm_oct_pow_netdev_ops = { - .ndo_init = cvm_oct_common_init, - .ndo_start_xmit = cvm_oct_xmit_pow, - .ndo_set_rx_mode = cvm_oct_common_set_multicast_list, - .ndo_set_mac_address = cvm_oct_common_set_mac_address, - .ndo_do_ioctl = cvm_oct_ioctl, - .ndo_change_mtu = cvm_oct_common_change_mtu, - .ndo_get_stats = cvm_oct_common_get_stats, -#ifdef CONFIG_NET_POLL_CONTROLLER - .ndo_poll_controller = cvm_oct_poll_controller, -#endif -}; - -static struct device_node *cvm_oct_of_get_child - (const struct device_node *parent, int reg_val) -{ - struct device_node *node = NULL; - int size; - const __be32 *addr; - - for (;;) { - node = of_get_next_child(parent, node); - if (!node) - break; - addr = of_get_property(node, "reg", &size); - if (addr && (be32_to_cpu(*addr) == reg_val)) - break; - } - return node; -} - -static struct device_node *cvm_oct_node_for_port(struct device_node *pip, - int interface, int port) -{ - struct device_node *ni, *np; - - ni = cvm_oct_of_get_child(pip, interface); - if (!ni) - return NULL; - - np = cvm_oct_of_get_child(ni, port); - of_node_put(ni); - - return np; -} - -static void cvm_set_rgmii_delay(struct octeon_ethernet *priv, int iface, - int port) -{ - struct device_node *np = priv->of_node; - u32 delay_value; - bool rx_delay; - bool tx_delay; - - /* By default, both RX/TX delay is enabled in - * __cvmx_helper_rgmii_enable(). - */ - rx_delay = true; - tx_delay = true; - - if (!of_property_read_u32(np, "rx-delay", &delay_value)) { - cvmx_write_csr(CVMX_ASXX_RX_CLK_SETX(port, iface), delay_value); - rx_delay = delay_value > 0; - } - if (!of_property_read_u32(np, "tx-delay", &delay_value)) { - cvmx_write_csr(CVMX_ASXX_TX_CLK_SETX(port, iface), delay_value); - tx_delay = delay_value > 0; - } - - if (!rx_delay && !tx_delay) - priv->phy_mode = PHY_INTERFACE_MODE_RGMII_ID; - else if (!rx_delay) - priv->phy_mode = PHY_INTERFACE_MODE_RGMII_RXID; - else if (!tx_delay) - priv->phy_mode = PHY_INTERFACE_MODE_RGMII_TXID; - else - priv->phy_mode = PHY_INTERFACE_MODE_RGMII; -} - -static int cvm_oct_probe(struct platform_device *pdev) -{ - int num_interfaces; - int interface; - int fau = FAU_NUM_PACKET_BUFFERS_TO_FREE; - int qos; - struct device_node *pip; - int mtu_overhead = ETH_HLEN + ETH_FCS_LEN; - -#if IS_ENABLED(CONFIG_VLAN_8021Q) - mtu_overhead += VLAN_HLEN; -#endif - - octeon_mdiobus_force_mod_depencency(); - - pip = pdev->dev.of_node; - if (!pip) { - pr_err("Error: No 'pip' in /aliases\n"); - return -EINVAL; - } - - cvm_oct_configure_common_hw(); - - cvmx_helper_initialize_packet_io_global(); - - if (receive_group_order) { - if (receive_group_order > 4) - receive_group_order = 4; - pow_receive_groups = (1 << (1 << receive_group_order)) - 1; - } else { - pow_receive_groups = BIT(pow_receive_group); - } - - /* Change the input group for all ports before input is enabled */ - num_interfaces = cvmx_helper_get_number_of_interfaces(); - for (interface = 0; interface < num_interfaces; interface++) { - int num_ports = cvmx_helper_ports_on_interface(interface); - int port; - - for (port = cvmx_helper_get_ipd_port(interface, 0); - port < cvmx_helper_get_ipd_port(interface, num_ports); - port++) { - union cvmx_pip_prt_tagx pip_prt_tagx; - - pip_prt_tagx.u64 = - cvmx_read_csr(CVMX_PIP_PRT_TAGX(port)); - - if (receive_group_order) { - int tag_mask; - - /* We support only 16 groups at the moment, so - * always disable the two additional "hidden" - * tag_mask bits on CN68XX. - */ - if (OCTEON_IS_MODEL(OCTEON_CN68XX)) - pip_prt_tagx.u64 |= 0x3ull << 44; - - tag_mask = ~((1 << receive_group_order) - 1); - pip_prt_tagx.s.grptagbase = 0; - pip_prt_tagx.s.grptagmask = tag_mask; - pip_prt_tagx.s.grptag = 1; - pip_prt_tagx.s.tag_mode = 0; - pip_prt_tagx.s.inc_prt_flag = 1; - pip_prt_tagx.s.ip6_dprt_flag = 1; - pip_prt_tagx.s.ip4_dprt_flag = 1; - pip_prt_tagx.s.ip6_sprt_flag = 1; - pip_prt_tagx.s.ip4_sprt_flag = 1; - pip_prt_tagx.s.ip6_dst_flag = 1; - pip_prt_tagx.s.ip4_dst_flag = 1; - pip_prt_tagx.s.ip6_src_flag = 1; - pip_prt_tagx.s.ip4_src_flag = 1; - pip_prt_tagx.s.grp = 0; - } else { - pip_prt_tagx.s.grptag = 0; - pip_prt_tagx.s.grp = pow_receive_group; - } - - cvmx_write_csr(CVMX_PIP_PRT_TAGX(port), - pip_prt_tagx.u64); - } - } - - cvmx_helper_ipd_and_packet_input_enable(); - - memset(cvm_oct_device, 0, sizeof(cvm_oct_device)); - - /* - * Initialize the FAU used for counting packet buffers that - * need to be freed. - */ - cvmx_fau_atomic_write32(FAU_NUM_PACKET_BUFFERS_TO_FREE, 0); - - /* Initialize the FAU used for counting tx SKBs that need to be freed */ - cvmx_fau_atomic_write32(FAU_TOTAL_TX_TO_CLEAN, 0); - - if ((pow_send_group != -1)) { - struct net_device *dev; - - dev = alloc_etherdev(sizeof(struct octeon_ethernet)); - if (dev) { - /* Initialize the device private structure. */ - struct octeon_ethernet *priv = netdev_priv(dev); - - SET_NETDEV_DEV(dev, &pdev->dev); - dev->netdev_ops = &cvm_oct_pow_netdev_ops; - priv->imode = CVMX_HELPER_INTERFACE_MODE_DISABLED; - priv->port = CVMX_PIP_NUM_INPUT_PORTS; - priv->queue = -1; - strscpy(dev->name, "pow%d", sizeof(dev->name)); - for (qos = 0; qos < 16; qos++) - skb_queue_head_init(&priv->tx_free_list[qos]); - dev->min_mtu = VLAN_ETH_ZLEN - mtu_overhead; - dev->max_mtu = OCTEON_MAX_MTU - mtu_overhead; - - if (register_netdev(dev) < 0) { - pr_err("Failed to register ethernet device for POW\n"); - free_netdev(dev); - } else { - cvm_oct_device[CVMX_PIP_NUM_INPUT_PORTS] = dev; - pr_info("%s: POW send group %d, receive group %d\n", - dev->name, pow_send_group, - pow_receive_group); - } - } else { - pr_err("Failed to allocate ethernet device for POW\n"); - } - } - - num_interfaces = cvmx_helper_get_number_of_interfaces(); - for (interface = 0; interface < num_interfaces; interface++) { - cvmx_helper_interface_mode_t imode = - cvmx_helper_interface_get_mode(interface); - int num_ports = cvmx_helper_ports_on_interface(interface); - int port; - int port_index; - - for (port_index = 0, - port = cvmx_helper_get_ipd_port(interface, 0); - port < cvmx_helper_get_ipd_port(interface, num_ports); - port_index++, port++) { - struct octeon_ethernet *priv; - struct net_device *dev = - alloc_etherdev(sizeof(struct octeon_ethernet)); - if (!dev) { - pr_err("Failed to allocate ethernet device for port %d\n", - port); - continue; - } - - /* Initialize the device private structure. */ - SET_NETDEV_DEV(dev, &pdev->dev); - priv = netdev_priv(dev); - priv->netdev = dev; - priv->of_node = cvm_oct_node_for_port(pip, interface, - port_index); - - INIT_DELAYED_WORK(&priv->port_periodic_work, - cvm_oct_periodic_worker); - priv->imode = imode; - priv->port = port; - priv->queue = cvmx_pko_get_base_queue(priv->port); - priv->fau = fau - cvmx_pko_get_num_queues(port) * 4; - priv->phy_mode = PHY_INTERFACE_MODE_NA; - for (qos = 0; qos < 16; qos++) - skb_queue_head_init(&priv->tx_free_list[qos]); - for (qos = 0; qos < cvmx_pko_get_num_queues(port); - qos++) - cvmx_fau_atomic_write32(priv->fau + qos * 4, 0); - dev->min_mtu = VLAN_ETH_ZLEN - mtu_overhead; - dev->max_mtu = OCTEON_MAX_MTU - mtu_overhead; - - switch (priv->imode) { - /* These types don't support ports to IPD/PKO */ - case CVMX_HELPER_INTERFACE_MODE_DISABLED: - case CVMX_HELPER_INTERFACE_MODE_PCIE: - case CVMX_HELPER_INTERFACE_MODE_PICMG: - break; - - case CVMX_HELPER_INTERFACE_MODE_NPI: - dev->netdev_ops = &cvm_oct_npi_netdev_ops; - strscpy(dev->name, "npi%d", sizeof(dev->name)); - break; - - case CVMX_HELPER_INTERFACE_MODE_XAUI: - dev->netdev_ops = &cvm_oct_xaui_netdev_ops; - strscpy(dev->name, "xaui%d", sizeof(dev->name)); - break; - - case CVMX_HELPER_INTERFACE_MODE_LOOP: - dev->netdev_ops = &cvm_oct_npi_netdev_ops; - strscpy(dev->name, "loop%d", sizeof(dev->name)); - break; - - case CVMX_HELPER_INTERFACE_MODE_SGMII: - priv->phy_mode = PHY_INTERFACE_MODE_SGMII; - dev->netdev_ops = &cvm_oct_sgmii_netdev_ops; - strscpy(dev->name, "eth%d", sizeof(dev->name)); - break; - - case CVMX_HELPER_INTERFACE_MODE_SPI: - dev->netdev_ops = &cvm_oct_spi_netdev_ops; - strscpy(dev->name, "spi%d", sizeof(dev->name)); - break; - - case CVMX_HELPER_INTERFACE_MODE_GMII: - priv->phy_mode = PHY_INTERFACE_MODE_GMII; - dev->netdev_ops = &cvm_oct_rgmii_netdev_ops; - strscpy(dev->name, "eth%d", sizeof(dev->name)); - break; - - case CVMX_HELPER_INTERFACE_MODE_RGMII: - dev->netdev_ops = &cvm_oct_rgmii_netdev_ops; - strscpy(dev->name, "eth%d", sizeof(dev->name)); - cvm_set_rgmii_delay(priv, interface, - port_index); - break; - } - - if (!dev->netdev_ops) { - free_netdev(dev); - } else if (register_netdev(dev) < 0) { - pr_err("Failed to register ethernet device for interface %d, port %d\n", - interface, priv->port); - free_netdev(dev); - } else { - cvm_oct_device[priv->port] = dev; - fau -= - cvmx_pko_get_num_queues(priv->port) * - sizeof(u32); - schedule_delayed_work(&priv->port_periodic_work, - HZ); - } - } - } - - cvm_oct_tx_initialize(); - cvm_oct_rx_initialize(); - - /* - * 150 uS: about 10 1500-byte packets at 1GE. - */ - cvm_oct_tx_poll_interval = 150 * (octeon_get_clock_rate() / 1000000); - - schedule_delayed_work(&cvm_oct_rx_refill_work, HZ); - - return 0; -} - -static int cvm_oct_remove(struct platform_device *pdev) -{ - int port; - - cvmx_ipd_disable(); - - atomic_inc_return(&cvm_oct_poll_queue_stopping); - cancel_delayed_work_sync(&cvm_oct_rx_refill_work); - - cvm_oct_rx_shutdown(); - cvm_oct_tx_shutdown(); - - cvmx_pko_disable(); - - /* Free the ethernet devices */ - for (port = 0; port < TOTAL_NUMBER_OF_PORTS; port++) { - if (cvm_oct_device[port]) { - struct net_device *dev = cvm_oct_device[port]; - struct octeon_ethernet *priv = netdev_priv(dev); - - cancel_delayed_work_sync(&priv->port_periodic_work); - - cvm_oct_tx_shutdown_dev(dev); - unregister_netdev(dev); - free_netdev(dev); - cvm_oct_device[port] = NULL; - } - } - - cvmx_pko_shutdown(); - - cvmx_ipd_free_ptr(); - - /* Free the HW pools */ - cvm_oct_mem_empty_fpa(CVMX_FPA_PACKET_POOL, CVMX_FPA_PACKET_POOL_SIZE, - num_packet_buffers); - cvm_oct_mem_empty_fpa(CVMX_FPA_WQE_POOL, CVMX_FPA_WQE_POOL_SIZE, - num_packet_buffers); - if (CVMX_FPA_OUTPUT_BUFFER_POOL != CVMX_FPA_PACKET_POOL) - cvm_oct_mem_empty_fpa(CVMX_FPA_OUTPUT_BUFFER_POOL, - CVMX_FPA_OUTPUT_BUFFER_POOL_SIZE, 128); - return 0; -} - -static const struct of_device_id cvm_oct_match[] = { - { - .compatible = "cavium,octeon-3860-pip", - }, - {}, -}; -MODULE_DEVICE_TABLE(of, cvm_oct_match); - -static struct platform_driver cvm_oct_driver = { - .probe = cvm_oct_probe, - .remove = cvm_oct_remove, - .driver = { - .name = KBUILD_MODNAME, - .of_match_table = cvm_oct_match, - }, -}; - -module_platform_driver(cvm_oct_driver); - -MODULE_LICENSE("GPL"); -MODULE_AUTHOR("Cavium Networks <support@caviumnetworks.com>"); -MODULE_DESCRIPTION("Cavium Networks Octeon ethernet driver."); diff --git a/drivers/staging/octeon/octeon-ethernet.h b/drivers/staging/octeon/octeon-ethernet.h deleted file mode 100644 index a6140705706f..000000000000 --- a/drivers/staging/octeon/octeon-ethernet.h +++ /dev/null @@ -1,107 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0 */ -/* - * This file is based on code from OCTEON SDK by Cavium Networks. - * - * Copyright (c) 2003-2010 Cavium Networks - */ - -/* - * External interface for the Cavium Octeon ethernet driver. - */ -#ifndef OCTEON_ETHERNET_H -#define OCTEON_ETHERNET_H - -#include <linux/of.h> -#include <linux/phy.h> - -#ifdef CONFIG_CAVIUM_OCTEON_SOC - -#include <asm/octeon/octeon.h> - -#include <asm/octeon/cvmx-asxx-defs.h> -#include <asm/octeon/cvmx-config.h> -#include <asm/octeon/cvmx-fau.h> -#include <asm/octeon/cvmx-gmxx-defs.h> -#include <asm/octeon/cvmx-helper.h> -#include <asm/octeon/cvmx-helper-util.h> -#include <asm/octeon/cvmx-ipd.h> -#include <asm/octeon/cvmx-ipd-defs.h> -#include <asm/octeon/cvmx-npi-defs.h> -#include <asm/octeon/cvmx-pip.h> -#include <asm/octeon/cvmx-pko.h> -#include <asm/octeon/cvmx-pow.h> -#include <asm/octeon/cvmx-scratch.h> -#include <asm/octeon/cvmx-spi.h> -#include <asm/octeon/cvmx-spxx-defs.h> -#include <asm/octeon/cvmx-stxx-defs.h> -#include <asm/octeon/cvmx-wqe.h> - -#else - -#include "octeon-stubs.h" - -#endif - -/** - * This is the definition of the Ethernet driver's private - * driver state stored in netdev_priv(dev). - */ -struct octeon_ethernet { - /* PKO hardware output port */ - int port; - /* PKO hardware queue for the port */ - int queue; - /* Hardware fetch and add to count outstanding tx buffers */ - int fau; - /* My netdev. */ - struct net_device *netdev; - /* - * Type of port. This is one of the enums in - * cvmx_helper_interface_mode_t - */ - int imode; - /* PHY mode */ - phy_interface_t phy_mode; - /* List of outstanding tx buffers per queue */ - struct sk_buff_head tx_free_list[16]; - unsigned int last_speed; - unsigned int last_link; - /* Last negotiated link state */ - u64 link_info; - /* Called periodically to check link status */ - void (*poll)(struct net_device *dev); - struct delayed_work port_periodic_work; - struct device_node *of_node; -}; - -int cvm_oct_free_work(void *work_queue_entry); - -int cvm_oct_rgmii_open(struct net_device *dev); - -int cvm_oct_sgmii_init(struct net_device *dev); -int cvm_oct_sgmii_open(struct net_device *dev); - -int cvm_oct_spi_init(struct net_device *dev); -void cvm_oct_spi_uninit(struct net_device *dev); - -int cvm_oct_common_init(struct net_device *dev); -void cvm_oct_common_uninit(struct net_device *dev); -void cvm_oct_adjust_link(struct net_device *dev); -int cvm_oct_common_stop(struct net_device *dev); -int cvm_oct_common_open(struct net_device *dev, - void (*link_poll)(struct net_device *)); -void cvm_oct_note_carrier(struct octeon_ethernet *priv, - union cvmx_helper_link_info li); -void cvm_oct_link_poll(struct net_device *dev); - -extern int always_use_pow; -extern int pow_send_group; -extern int pow_receive_groups; -extern char pow_send_list[]; -extern struct net_device *cvm_oct_device[]; -extern atomic_t cvm_oct_poll_queue_stopping; -extern u64 cvm_oct_tx_poll_interval; - -extern int rx_napi_weight; - -#endif diff --git a/drivers/staging/octeon/octeon-stubs.h b/drivers/staging/octeon/octeon-stubs.h deleted file mode 100644 index 79213c045504..000000000000 --- a/drivers/staging/octeon/octeon-stubs.h +++ /dev/null @@ -1,1433 +0,0 @@ -#define CONFIG_CAVIUM_OCTEON_CVMSEG_SIZE 512 - -#ifndef XKPHYS_TO_PHYS -# define XKPHYS_TO_PHYS(p) (p) -#endif - -#define OCTEON_IRQ_WORKQ0 0 -#define OCTEON_IRQ_RML 0 -#define OCTEON_IRQ_TIMER1 0 -#define OCTEON_IS_MODEL(x) 0 -#define octeon_has_feature(x) 0 -#define octeon_get_clock_rate() 0 - -#define CVMX_SYNCIOBDMA do { } while(0) - -#define CVMX_HELPER_INPUT_TAG_TYPE 0 -#define CVMX_HELPER_FIRST_MBUFF_SKIP 7 -#define CVMX_FAU_REG_END (2048) -#define CVMX_FPA_OUTPUT_BUFFER_POOL (2) -#define CVMX_FPA_OUTPUT_BUFFER_POOL_SIZE 16 -#define CVMX_FPA_PACKET_POOL (0) -#define CVMX_FPA_PACKET_POOL_SIZE 16 -#define CVMX_FPA_WQE_POOL (1) -#define CVMX_FPA_WQE_POOL_SIZE 16 -#define CVMX_GMXX_RXX_ADR_CAM_EN(a, b) ((a)+(b)) -#define CVMX_GMXX_RXX_ADR_CTL(a, b) ((a)+(b)) -#define CVMX_GMXX_PRTX_CFG(a, b) ((a)+(b)) -#define CVMX_GMXX_RXX_FRM_MAX(a, b) ((a)+(b)) -#define CVMX_GMXX_RXX_JABBER(a, b) ((a)+(b)) -#define CVMX_IPD_CTL_STATUS 0 -#define CVMX_PIP_FRM_LEN_CHKX(a) (a) -#define CVMX_PIP_NUM_INPUT_PORTS 1 -#define CVMX_SCR_SCRATCH 0 -#define CVMX_PKO_QUEUES_PER_PORT_INTERFACE0 2 -#define CVMX_PKO_QUEUES_PER_PORT_INTERFACE1 2 -#define CVMX_IPD_SUB_PORT_FCS 0 -#define CVMX_SSO_WQ_IQ_DIS 0 -#define CVMX_SSO_WQ_INT 0 -#define CVMX_POW_WQ_INT 0 -#define CVMX_SSO_WQ_INT_PC 0 -#define CVMX_NPI_RSL_INT_BLOCKS 0 -#define CVMX_POW_WQ_INT_PC 0 - -union cvmx_pip_wqe_word2 { - uint64_t u64; - struct { - uint64_t bufs:8; - uint64_t ip_offset:8; - uint64_t vlan_valid:1; - uint64_t vlan_stacked:1; - uint64_t unassigned:1; - uint64_t vlan_cfi:1; - uint64_t vlan_id:12; - uint64_t pr:4; - uint64_t unassigned2:8; - uint64_t dec_ipcomp:1; - uint64_t tcp_or_udp:1; - uint64_t dec_ipsec:1; - uint64_t is_v6:1; - uint64_t software:1; - uint64_t L4_error:1; - uint64_t is_frag:1; - uint64_t IP_exc:1; - uint64_t is_bcast:1; - uint64_t is_mcast:1; - uint64_t not_IP:1; - uint64_t rcv_error:1; - uint64_t err_code:8; - } s; - struct { - uint64_t bufs:8; - uint64_t ip_offset:8; - uint64_t vlan_valid:1; - uint64_t vlan_stacked:1; - uint64_t unassigned:1; - uint64_t vlan_cfi:1; - uint64_t vlan_id:12; - uint64_t port:12; - uint64_t dec_ipcomp:1; - uint64_t tcp_or_udp:1; - uint64_t dec_ipsec:1; - uint64_t is_v6:1; - uint64_t software:1; - uint64_t L4_error:1; - uint64_t is_frag:1; - uint64_t IP_exc:1; - uint64_t is_bcast:1; - uint64_t is_mcast:1; - uint64_t not_IP:1; - uint64_t rcv_error:1; - uint64_t err_code:8; - } s_cn68xx; - - struct { - uint64_t unused1:16; - uint64_t vlan:16; - uint64_t unused2:32; - } svlan; - struct { - uint64_t bufs:8; - uint64_t unused:8; - uint64_t vlan_valid:1; - uint64_t vlan_stacked:1; - uint64_t unassigned:1; - uint64_t vlan_cfi:1; - uint64_t vlan_id:12; - uint64_t pr:4; - uint64_t unassigned2:12; - uint64_t software:1; - uint64_t unassigned3:1; - uint64_t is_rarp:1; - uint64_t is_arp:1; - uint64_t is_bcast:1; - uint64_t is_mcast:1; - uint64_t not_IP:1; - uint64_t rcv_error:1; - uint64_t err_code:8; - } snoip; - -}; - -union cvmx_pip_wqe_word0 { - struct { - uint64_t next_ptr:40; - uint8_t unused; - __wsum hw_chksum; - } cn38xx; - struct { - uint64_t pknd:6; /* 0..5 */ - uint64_t unused2:2; /* 6..7 */ - uint64_t bpid:6; /* 8..13 */ - uint64_t unused1:18; /* 14..31 */ - uint64_t l2ptr:8; /* 32..39 */ - uint64_t l3ptr:8; /* 40..47 */ - uint64_t unused0:8; /* 48..55 */ - uint64_t l4ptr:8; /* 56..63 */ - } cn68xx; -}; - -union cvmx_wqe_word0 { - uint64_t u64; - union cvmx_pip_wqe_word0 pip; -}; - -union cvmx_wqe_word1 { - uint64_t u64; - struct { - uint64_t tag:32; - uint64_t tag_type:2; - uint64_t varies:14; - uint64_t len:16; - }; - struct { - uint64_t tag:32; - uint64_t tag_type:2; - uint64_t zero_2:3; - uint64_t grp:6; - uint64_t zero_1:1; - uint64_t qos:3; - uint64_t zero_0:1; - uint64_t len:16; - } cn68xx; - struct { - uint64_t tag:32; - uint64_t tag_type:2; - uint64_t zero_2:1; - uint64_t grp:4; - uint64_t qos:3; - uint64_t ipprt:6; - uint64_t len:16; - } cn38xx; -}; - -union cvmx_buf_ptr { - void *ptr; - uint64_t u64; - struct { - uint64_t i:1; - uint64_t back:4; - uint64_t pool:3; - uint64_t size:16; - uint64_t addr:40; - } s; -}; - -struct cvmx_wqe { - union cvmx_wqe_word0 word0; - union cvmx_wqe_word1 word1; - union cvmx_pip_wqe_word2 word2; - union cvmx_buf_ptr packet_ptr; - uint8_t packet_data[96]; -}; - -union cvmx_helper_link_info { - uint64_t u64; - struct { - uint64_t reserved_20_63:44; - uint64_t link_up:1; /**< Is the physical link up? */ - uint64_t full_duplex:1; /**< 1 if the link is full duplex */ - uint64_t speed:18; /**< Speed of the link in Mbps */ - } s; -}; - -enum cvmx_fau_reg_32 { - CVMX_FAU_REG_32_START = 0, -}; - -enum cvmx_fau_op_size { - CVMX_FAU_OP_SIZE_8 = 0, - CVMX_FAU_OP_SIZE_16 = 1, - CVMX_FAU_OP_SIZE_32 = 2, - CVMX_FAU_OP_SIZE_64 = 3 -}; - -typedef enum { - CVMX_SPI_MODE_UNKNOWN = 0, - CVMX_SPI_MODE_TX_HALFPLEX = 1, - CVMX_SPI_MODE_RX_HALFPLEX = 2, - CVMX_SPI_MODE_DUPLEX = 3 -} cvmx_spi_mode_t; - -typedef enum { - CVMX_HELPER_INTERFACE_MODE_DISABLED, - CVMX_HELPER_INTERFACE_MODE_RGMII, - CVMX_HELPER_INTERFACE_MODE_GMII, - CVMX_HELPER_INTERFACE_MODE_SPI, - CVMX_HELPER_INTERFACE_MODE_PCIE, - CVMX_HELPER_INTERFACE_MODE_XAUI, - CVMX_HELPER_INTERFACE_MODE_SGMII, - CVMX_HELPER_INTERFACE_MODE_PICMG, - CVMX_HELPER_INTERFACE_MODE_NPI, - CVMX_HELPER_INTERFACE_MODE_LOOP, -} cvmx_helper_interface_mode_t; - -typedef enum { - CVMX_POW_WAIT = 1, - CVMX_POW_NO_WAIT = 0, -} cvmx_pow_wait_t; - -typedef enum { - CVMX_PKO_LOCK_NONE = 0, - CVMX_PKO_LOCK_ATOMIC_TAG = 1, - CVMX_PKO_LOCK_CMD_QUEUE = 2, -} cvmx_pko_lock_t; - -typedef enum { - CVMX_PKO_SUCCESS, - CVMX_PKO_INVALID_PORT, - CVMX_PKO_INVALID_QUEUE, - CVMX_PKO_INVALID_PRIORITY, - CVMX_PKO_NO_MEMORY, - CVMX_PKO_PORT_ALREADY_SETUP, - CVMX_PKO_CMD_QUEUE_INIT_ERROR -} cvmx_pko_status_t; - -enum cvmx_pow_tag_type { - CVMX_POW_TAG_TYPE_ORDERED = 0L, - CVMX_POW_TAG_TYPE_ATOMIC = 1L, - CVMX_POW_TAG_TYPE_NULL = 2L, - CVMX_POW_TAG_TYPE_NULL_NULL = 3L -}; - -union cvmx_ipd_ctl_status { - uint64_t u64; - struct cvmx_ipd_ctl_status_s { - uint64_t reserved_18_63:46; - uint64_t use_sop:1; - uint64_t rst_done:1; - uint64_t clken:1; - uint64_t no_wptr:1; - uint64_t pq_apkt:1; - uint64_t pq_nabuf:1; - uint64_t ipd_full:1; - uint64_t pkt_off:1; - uint64_t len_m8:1; - uint64_t reset:1; - uint64_t addpkt:1; - uint64_t naddbuf:1; - uint64_t pkt_lend:1; - uint64_t wqe_lend:1; - uint64_t pbp_en:1; - uint64_t opc_mode:2; - uint64_t ipd_en:1; - } s; - struct cvmx_ipd_ctl_status_cn30xx { - uint64_t reserved_10_63:54; - uint64_t len_m8:1; - uint64_t reset:1; - uint64_t addpkt:1; - uint64_t naddbuf:1; - uint64_t pkt_lend:1; - uint64_t wqe_lend:1; - uint64_t pbp_en:1; - uint64_t opc_mode:2; - uint64_t ipd_en:1; - } cn30xx; - struct cvmx_ipd_ctl_status_cn38xxp2 { - uint64_t reserved_9_63:55; - uint64_t reset:1; - uint64_t addpkt:1; - uint64_t naddbuf:1; - uint64_t pkt_lend:1; - uint64_t wqe_lend:1; - uint64_t pbp_en:1; - uint64_t opc_mode:2; - uint64_t ipd_en:1; - } cn38xxp2; - struct cvmx_ipd_ctl_status_cn50xx { - uint64_t reserved_15_63:49; - uint64_t no_wptr:1; - uint64_t pq_apkt:1; - uint64_t pq_nabuf:1; - uint64_t ipd_full:1; - uint64_t pkt_off:1; - uint64_t len_m8:1; - uint64_t reset:1; - uint64_t addpkt:1; - uint64_t naddbuf:1; - uint64_t pkt_lend:1; - uint64_t wqe_lend:1; - uint64_t pbp_en:1; - uint64_t opc_mode:2; - uint64_t ipd_en:1; - } cn50xx; - struct cvmx_ipd_ctl_status_cn58xx { - uint64_t reserved_12_63:52; - uint64_t ipd_full:1; - uint64_t pkt_off:1; - uint64_t len_m8:1; - uint64_t reset:1; - uint64_t addpkt:1; - uint64_t naddbuf:1; - uint64_t pkt_lend:1; - uint64_t wqe_lend:1; - uint64_t pbp_en:1; - uint64_t opc_mode:2; - uint64_t ipd_en:1; - } cn58xx; - struct cvmx_ipd_ctl_status_cn63xxp1 { - uint64_t reserved_16_63:48; - uint64_t clken:1; - uint64_t no_wptr:1; - uint64_t pq_apkt:1; - uint64_t pq_nabuf:1; - uint64_t ipd_full:1; - uint64_t pkt_off:1; - uint64_t len_m8:1; - uint64_t reset:1; - uint64_t addpkt:1; - uint64_t naddbuf:1; - uint64_t pkt_lend:1; - uint64_t wqe_lend:1; - uint64_t pbp_en:1; - uint64_t opc_mode:2; - uint64_t ipd_en:1; - } cn63xxp1; -}; - -union cvmx_ipd_sub_port_fcs { - uint64_t u64; - struct cvmx_ipd_sub_port_fcs_s { - uint64_t port_bit:32; - uint64_t reserved_32_35:4; - uint64_t port_bit2:4; - uint64_t reserved_40_63:24; - } s; - struct cvmx_ipd_sub_port_fcs_cn30xx { - uint64_t port_bit:3; - uint64_t reserved_3_63:61; - } cn30xx; - struct cvmx_ipd_sub_port_fcs_cn38xx { - uint64_t port_bit:32; - uint64_t reserved_32_63:32; - } cn38xx; -}; - -union cvmx_ipd_sub_port_qos_cnt { - uint64_t u64; - struct cvmx_ipd_sub_port_qos_cnt_s { - uint64_t cnt:32; - uint64_t port_qos:9; - uint64_t reserved_41_63:23; - } s; -}; -typedef struct { - uint32_t dropped_octets; - uint32_t dropped_packets; - uint32_t pci_raw_packets; - uint32_t octets; - uint32_t packets; - uint32_t multicast_packets; - uint32_t broadcast_packets; - uint32_t len_64_packets; - uint32_t len_65_127_packets; - uint32_t len_128_255_packets; - uint32_t len_256_511_packets; - uint32_t len_512_1023_packets; - uint32_t len_1024_1518_packets; - uint32_t len_1519_max_packets; - uint32_t fcs_align_err_packets; - uint32_t runt_packets; - uint32_t runt_crc_packets; - uint32_t oversize_packets; - uint32_t oversize_crc_packets; - uint32_t inb_packets; - uint64_t inb_octets; - uint16_t inb_errors; -} cvmx_pip_port_status_t; - -typedef struct { - uint32_t packets; - uint64_t octets; - uint64_t doorbell; -} cvmx_pko_port_status_t; - -union cvmx_pip_frm_len_chkx { - uint64_t u64; - struct cvmx_pip_frm_len_chkx_s { - uint64_t reserved_32_63:32; - uint64_t maxlen:16; - uint64_t minlen:16; - } s; -}; - -union cvmx_gmxx_rxx_frm_ctl { - uint64_t u64; - struct cvmx_gmxx_rxx_frm_ctl_s { - uint64_t pre_chk:1; - uint64_t pre_strp:1; - uint64_t ctl_drp:1; - uint64_t ctl_bck:1; - uint64_t ctl_mcst:1; - uint64_t ctl_smac:1; - uint64_t pre_free:1; - uint64_t vlan_len:1; - uint64_t pad_len:1; - uint64_t pre_align:1; - uint64_t null_dis:1; - uint64_t reserved_11_11:1; - uint64_t ptp_mode:1; - uint64_t reserved_13_63:51; - } s; - struct cvmx_gmxx_rxx_frm_ctl_cn30xx { - uint64_t pre_chk:1; - uint64_t pre_strp:1; - uint64_t ctl_drp:1; - uint64_t ctl_bck:1; - uint64_t ctl_mcst:1; - uint64_t ctl_smac:1; - uint64_t pre_free:1; - uint64_t vlan_len:1; - uint64_t pad_len:1; - uint64_t reserved_9_63:55; - } cn30xx; - struct cvmx_gmxx_rxx_frm_ctl_cn31xx { - uint64_t pre_chk:1; - uint64_t pre_strp:1; - uint64_t ctl_drp:1; - uint64_t ctl_bck:1; - uint64_t ctl_mcst:1; - uint64_t ctl_smac:1; - uint64_t pre_free:1; - uint64_t vlan_len:1; - uint64_t reserved_8_63:56; - } cn31xx; - struct cvmx_gmxx_rxx_frm_ctl_cn50xx { - uint64_t pre_chk:1; - uint64_t pre_strp:1; - uint64_t ctl_drp:1; - uint64_t ctl_bck:1; - uint64_t ctl_mcst:1; - uint64_t ctl_smac:1; - uint64_t pre_free:1; - uint64_t reserved_7_8:2; - uint64_t pre_align:1; - uint64_t null_dis:1; - uint64_t reserved_11_63:53; - } cn50xx; - struct cvmx_gmxx_rxx_frm_ctl_cn56xxp1 { - uint64_t pre_chk:1; - uint64_t pre_strp:1; - uint64_t ctl_drp:1; - uint64_t ctl_bck:1; - uint64_t ctl_mcst:1; - uint64_t ctl_smac:1; - uint64_t pre_free:1; - uint64_t reserved_7_8:2; - uint64_t pre_align:1; - uint64_t reserved_10_63:54; - } cn56xxp1; - struct cvmx_gmxx_rxx_frm_ctl_cn58xx { - uint64_t pre_chk:1; - uint64_t pre_strp:1; - uint64_t ctl_drp:1; - uint64_t ctl_bck:1; - uint64_t ctl_mcst:1; - uint64_t ctl_smac:1; - uint64_t pre_free:1; - uint64_t vlan_len:1; - uint64_t pad_len:1; - uint64_t pre_align:1; - uint64_t null_dis:1; - uint64_t reserved_11_63:53; - } cn58xx; - struct cvmx_gmxx_rxx_frm_ctl_cn61xx { - uint64_t pre_chk:1; - uint64_t pre_strp:1; - uint64_t ctl_drp:1; - uint64_t ctl_bck:1; - uint64_t ctl_mcst:1; - uint64_t ctl_smac:1; - uint64_t pre_free:1; - uint64_t reserved_7_8:2; - uint64_t pre_align:1; - uint64_t null_dis:1; - uint64_t reserved_11_11:1; - uint64_t ptp_mode:1; - uint64_t reserved_13_63:51; - } cn61xx; -}; - -union cvmx_gmxx_rxx_int_reg { - uint64_t u64; - struct cvmx_gmxx_rxx_int_reg_s { - uint64_t minerr:1; - uint64_t carext:1; - uint64_t maxerr:1; - uint64_t jabber:1; - uint64_t fcserr:1; - uint64_t alnerr:1; - uint64_t lenerr:1; - uint64_t rcverr:1; - uint64_t skperr:1; - uint64_t niberr:1; - uint64_t ovrerr:1; - uint64_t pcterr:1; - uint64_t rsverr:1; - uint64_t falerr:1; - uint64_t coldet:1; - uint64_t ifgerr:1; - uint64_t phy_link:1; - uint64_t phy_spd:1; - uint64_t phy_dupx:1; - uint64_t pause_drp:1; - uint64_t loc_fault:1; - uint64_t rem_fault:1; - uint64_t bad_seq:1; - uint64_t bad_term:1; - uint64_t unsop:1; - uint64_t uneop:1; - uint64_t undat:1; - uint64_t hg2fld:1; - uint64_t hg2cc:1; - uint64_t reserved_29_63:35; - } s; - struct cvmx_gmxx_rxx_int_reg_cn30xx { - uint64_t minerr:1; - uint64_t carext:1; - uint64_t maxerr:1; - uint64_t jabber:1; - uint64_t fcserr:1; - uint64_t alnerr:1; - uint64_t lenerr:1; - uint64_t rcverr:1; - uint64_t skperr:1; - uint64_t niberr:1; - uint64_t ovrerr:1; - uint64_t pcterr:1; - uint64_t rsverr:1; - uint64_t falerr:1; - uint64_t coldet:1; - uint64_t ifgerr:1; - uint64_t phy_link:1; - uint64_t phy_spd:1; - uint64_t phy_dupx:1; - uint64_t reserved_19_63:45; - } cn30xx; - struct cvmx_gmxx_rxx_int_reg_cn50xx { - uint64_t reserved_0_0:1; - uint64_t carext:1; - uint64_t reserved_2_2:1; - uint64_t jabber:1; - uint64_t fcserr:1; - uint64_t alnerr:1; - uint64_t reserved_6_6:1; - uint64_t rcverr:1; - uint64_t skperr:1; - uint64_t niberr:1; - uint64_t ovrerr:1; - uint64_t pcterr:1; - uint64_t rsverr:1; - uint64_t falerr:1; - uint64_t coldet:1; - uint64_t ifgerr:1; - uint64_t phy_link:1; - uint64_t phy_spd:1; - uint64_t phy_dupx:1; - uint64_t pause_drp:1; - uint64_t reserved_20_63:44; - } cn50xx; - struct cvmx_gmxx_rxx_int_reg_cn52xx { - uint64_t reserved_0_0:1; - uint64_t carext:1; - uint64_t reserved_2_2:1; - uint64_t jabber:1; - uint64_t fcserr:1; - uint64_t reserved_5_6:2; - uint64_t rcverr:1; - uint64_t skperr:1; - uint64_t reserved_9_9:1; - uint64_t ovrerr:1; - uint64_t pcterr:1; - uint64_t rsverr:1; - uint64_t falerr:1; - uint64_t coldet:1; - uint64_t ifgerr:1; - uint64_t reserved_16_18:3; - uint64_t pause_drp:1; - uint64_t loc_fault:1; - uint64_t rem_fault:1; - uint64_t bad_seq:1; - uint64_t bad_term:1; - uint64_t unsop:1; - uint64_t uneop:1; - uint64_t undat:1; - uint64_t hg2fld:1; - uint64_t hg2cc:1; - uint64_t reserved_29_63:35; - } cn52xx; - struct cvmx_gmxx_rxx_int_reg_cn56xxp1 { - uint64_t reserved_0_0:1; - uint64_t carext:1; - uint64_t reserved_2_2:1; - uint64_t jabber:1; - uint64_t fcserr:1; - uint64_t reserved_5_6:2; - uint64_t rcverr:1; - uint64_t skperr:1; - uint64_t reserved_9_9:1; - uint64_t ovrerr:1; - uint64_t pcterr:1; - uint64_t rsverr:1; - uint64_t falerr:1; - uint64_t coldet:1; - uint64_t ifgerr:1; - uint64_t reserved_16_18:3; - uint64_t pause_drp:1; - uint64_t loc_fault:1; - uint64_t rem_fault:1; - uint64_t bad_seq:1; - uint64_t bad_term:1; - uint64_t unsop:1; - uint64_t uneop:1; - uint64_t undat:1; - uint64_t reserved_27_63:37; - } cn56xxp1; - struct cvmx_gmxx_rxx_int_reg_cn58xx { - uint64_t minerr:1; - uint64_t carext:1; - uint64_t maxerr:1; - uint64_t jabber:1; - uint64_t fcserr:1; - uint64_t alnerr:1; - uint64_t lenerr:1; - uint64_t rcverr:1; - uint64_t skperr:1; - uint64_t niberr:1; - uint64_t ovrerr:1; - uint64_t pcterr:1; - uint64_t rsverr:1; - uint64_t falerr:1; - uint64_t coldet:1; - uint64_t ifgerr:1; - uint64_t phy_link:1; - uint64_t phy_spd:1; - uint64_t phy_dupx:1; - uint64_t pause_drp:1; - uint64_t reserved_20_63:44; - } cn58xx; - struct cvmx_gmxx_rxx_int_reg_cn61xx { - uint64_t minerr:1; - uint64_t carext:1; - uint64_t reserved_2_2:1; - uint64_t jabber:1; - uint64_t fcserr:1; - uint64_t reserved_5_6:2; - uint64_t rcverr:1; - uint64_t skperr:1; - uint64_t reserved_9_9:1; - uint64_t ovrerr:1; - uint64_t pcterr:1; - uint64_t rsverr:1; - uint64_t falerr:1; - uint64_t coldet:1; - uint64_t ifgerr:1; - uint64_t reserved_16_18:3; - uint64_t pause_drp:1; - uint64_t loc_fault:1; - uint64_t rem_fault:1; - uint64_t bad_seq:1; - uint64_t bad_term:1; - uint64_t unsop:1; - uint64_t uneop:1; - uint64_t undat:1; - uint64_t hg2fld:1; - uint64_t hg2cc:1; - uint64_t reserved_29_63:35; - } cn61xx; -}; - -union cvmx_gmxx_prtx_cfg { - uint64_t u64; - struct cvmx_gmxx_prtx_cfg_s { - uint64_t reserved_22_63:42; - uint64_t pknd:6; - uint64_t reserved_14_15:2; - uint64_t tx_idle:1; - uint64_t rx_idle:1; - uint64_t reserved_9_11:3; - uint64_t speed_msb:1; - uint64_t reserved_4_7:4; - uint64_t slottime:1; - uint64_t duplex:1; - uint64_t speed:1; - uint64_t en:1; - } s; - struct cvmx_gmxx_prtx_cfg_cn30xx { - uint64_t reserved_4_63:60; - uint64_t slottime:1; - uint64_t duplex:1; - uint64_t speed:1; - uint64_t en:1; - } cn30xx; - struct cvmx_gmxx_prtx_cfg_cn52xx { - uint64_t reserved_14_63:50; - uint64_t tx_idle:1; - uint64_t rx_idle:1; - uint64_t reserved_9_11:3; - uint64_t speed_msb:1; - uint64_t reserved_4_7:4; - uint64_t slottime:1; - uint64_t duplex:1; - uint64_t speed:1; - uint64_t en:1; - } cn52xx; -}; - -union cvmx_gmxx_rxx_adr_ctl { - uint64_t u64; - struct cvmx_gmxx_rxx_adr_ctl_s { - uint64_t reserved_4_63:60; - uint64_t cam_mode:1; - uint64_t mcst:2; - uint64_t bcst:1; - } s; -}; - -union cvmx_pip_prt_tagx { - uint64_t u64; - struct cvmx_pip_prt_tagx_s { - uint64_t reserved_54_63:10; - uint64_t portadd_en:1; - uint64_t inc_hwchk:1; - uint64_t reserved_50_51:2; - uint64_t grptagbase_msb:2; - uint64_t reserved_46_47:2; - uint64_t grptagmask_msb:2; - uint64_t reserved_42_43:2; - uint64_t grp_msb:2; - uint64_t grptagbase:4; - uint64_t grptagmask:4; - uint64_t grptag:1; - uint64_t grptag_mskip:1; - uint64_t tag_mode:2; - uint64_t inc_vs:2; - uint64_t inc_vlan:1; - uint64_t inc_prt_flag:1; - uint64_t ip6_dprt_flag:1; - uint64_t ip4_dprt_flag:1; - uint64_t ip6_sprt_flag:1; - uint64_t ip4_sprt_flag:1; - uint64_t ip6_nxth_flag:1; - uint64_t ip4_pctl_flag:1; - uint64_t ip6_dst_flag:1; - uint64_t ip4_dst_flag:1; - uint64_t ip6_src_flag:1; - uint64_t ip4_src_flag:1; - uint64_t tcp6_tag_type:2; - uint64_t tcp4_tag_type:2; - uint64_t ip6_tag_type:2; - uint64_t ip4_tag_type:2; - uint64_t non_tag_type:2; - uint64_t grp:4; - } s; - struct cvmx_pip_prt_tagx_cn30xx { - uint64_t reserved_40_63:24; - uint64_t grptagbase:4; - uint64_t grptagmask:4; - uint64_t grptag:1; - uint64_t reserved_30_30:1; - uint64_t tag_mode:2; - uint64_t inc_vs:2; - uint64_t inc_vlan:1; - uint64_t inc_prt_flag:1; - uint64_t ip6_dprt_flag:1; - uint64_t ip4_dprt_flag:1; - uint64_t ip6_sprt_flag:1; - uint64_t ip4_sprt_flag:1; - uint64_t ip6_nxth_flag:1; - uint64_t ip4_pctl_flag:1; - uint64_t ip6_dst_flag:1; - uint64_t ip4_dst_flag:1; - uint64_t ip6_src_flag:1; - uint64_t ip4_src_flag:1; - uint64_t tcp6_tag_type:2; - uint64_t tcp4_tag_type:2; - uint64_t ip6_tag_type:2; - uint64_t ip4_tag_type:2; - uint64_t non_tag_type:2; - uint64_t grp:4; - } cn30xx; - struct cvmx_pip_prt_tagx_cn50xx { - uint64_t reserved_40_63:24; - uint64_t grptagbase:4; - uint64_t grptagmask:4; - uint64_t grptag:1; - uint64_t grptag_mskip:1; - uint64_t tag_mode:2; - uint64_t inc_vs:2; - uint64_t inc_vlan:1; - uint64_t inc_prt_flag:1; - uint64_t ip6_dprt_flag:1; - uint64_t ip4_dprt_flag:1; - uint64_t ip6_sprt_flag:1; - uint64_t ip4_sprt_flag:1; - uint64_t ip6_nxth_flag:1; - uint64_t ip4_pctl_flag:1; - uint64_t ip6_dst_flag:1; - uint64_t ip4_dst_flag:1; - uint64_t ip6_src_flag:1; - uint64_t ip4_src_flag:1; - uint64_t tcp6_tag_type:2; - uint64_t tcp4_tag_type:2; - uint64_t ip6_tag_type:2; - uint64_t ip4_tag_type:2; - uint64_t non_tag_type:2; - uint64_t grp:4; - } cn50xx; -}; - -union cvmx_spxx_int_reg { - uint64_t u64; - struct cvmx_spxx_int_reg_s { - uint64_t reserved_32_63:32; - uint64_t spf:1; - uint64_t reserved_12_30:19; - uint64_t calerr:1; - uint64_t syncerr:1; - uint64_t diperr:1; - uint64_t tpaovr:1; - uint64_t rsverr:1; - uint64_t drwnng:1; - uint64_t clserr:1; - uint64_t spiovr:1; - uint64_t reserved_2_3:2; - uint64_t abnorm:1; - uint64_t prtnxa:1; - } s; -}; - -union cvmx_spxx_int_msk { - uint64_t u64; - struct cvmx_spxx_int_msk_s { - uint64_t reserved_12_63:52; - uint64_t calerr:1; - uint64_t syncerr:1; - uint64_t diperr:1; - uint64_t tpaovr:1; - uint64_t rsverr:1; - uint64_t drwnng:1; - uint64_t clserr:1; - uint64_t spiovr:1; - uint64_t reserved_2_3:2; - uint64_t abnorm:1; - uint64_t prtnxa:1; - } s; -}; - -union cvmx_pow_wq_int { - uint64_t u64; - struct cvmx_pow_wq_int_s { - uint64_t wq_int:16; - uint64_t iq_dis:16; - uint64_t reserved_32_63:32; - } s; -}; - -union cvmx_sso_wq_int_thrx { - uint64_t u64; - struct { - uint64_t iq_thr:12; - uint64_t reserved_12_13:2; - uint64_t ds_thr:12; - uint64_t reserved_26_27:2; - uint64_t tc_thr:4; - uint64_t tc_en:1; - uint64_t reserved_33_63:31; - } s; -}; - -union cvmx_stxx_int_reg { - uint64_t u64; - struct cvmx_stxx_int_reg_s { - uint64_t reserved_9_63:55; - uint64_t syncerr:1; - uint64_t frmerr:1; - uint64_t unxfrm:1; - uint64_t nosync:1; - uint64_t diperr:1; - uint64_t datovr:1; - uint64_t ovrbst:1; - uint64_t calpar1:1; - uint64_t calpar0:1; - } s; -}; - -union cvmx_stxx_int_msk { - uint64_t u64; - struct cvmx_stxx_int_msk_s { - uint64_t reserved_8_63:56; - uint64_t frmerr:1; - uint64_t unxfrm:1; - uint64_t nosync:1; - uint64_t diperr:1; - uint64_t datovr:1; - uint64_t ovrbst:1; - uint64_t calpar1:1; - uint64_t calpar0:1; - } s; -}; - -union cvmx_pow_wq_int_pc { - uint64_t u64; - struct cvmx_pow_wq_int_pc_s { - uint64_t reserved_0_7:8; - uint64_t pc_thr:20; - uint64_t reserved_28_31:4; - uint64_t pc:28; - uint64_t reserved_60_63:4; - } s; -}; - -union cvmx_pow_wq_int_thrx { - uint64_t u64; - struct cvmx_pow_wq_int_thrx_s { - uint64_t reserved_29_63:35; - uint64_t tc_en:1; - uint64_t tc_thr:4; - uint64_t reserved_23_23:1; - uint64_t ds_thr:11; - uint64_t reserved_11_11:1; - uint64_t iq_thr:11; - } s; - struct cvmx_pow_wq_int_thrx_cn30xx { - uint64_t reserved_29_63:35; - uint64_t tc_en:1; - uint64_t tc_thr:4; - uint64_t reserved_18_23:6; - uint64_t ds_thr:6; - uint64_t reserved_6_11:6; - uint64_t iq_thr:6; - } cn30xx; - struct cvmx_pow_wq_int_thrx_cn31xx { - uint64_t reserved_29_63:35; - uint64_t tc_en:1; - uint64_t tc_thr:4; - uint64_t reserved_20_23:4; - uint64_t ds_thr:8; - uint64_t reserved_8_11:4; - uint64_t iq_thr:8; - } cn31xx; - struct cvmx_pow_wq_int_thrx_cn52xx { - uint64_t reserved_29_63:35; - uint64_t tc_en:1; - uint64_t tc_thr:4; - uint64_t reserved_21_23:3; - uint64_t ds_thr:9; - uint64_t reserved_9_11:3; - uint64_t iq_thr:9; - } cn52xx; - struct cvmx_pow_wq_int_thrx_cn63xx { - uint64_t reserved_29_63:35; - uint64_t tc_en:1; - uint64_t tc_thr:4; - uint64_t reserved_22_23:2; - uint64_t ds_thr:10; - uint64_t reserved_10_11:2; - uint64_t iq_thr:10; - } cn63xx; -}; - -union cvmx_npi_rsl_int_blocks { - uint64_t u64; - struct cvmx_npi_rsl_int_blocks_s { - uint64_t reserved_32_63:32; - uint64_t rint_31:1; - uint64_t iob:1; - uint64_t reserved_28_29:2; - uint64_t rint_27:1; - uint64_t rint_26:1; - uint64_t rint_25:1; - uint64_t rint_24:1; - uint64_t asx1:1; - uint64_t asx0:1; - uint64_t rint_21:1; - uint64_t pip:1; - uint64_t spx1:1; - uint64_t spx0:1; - uint64_t lmc:1; - uint64_t l2c:1; - uint64_t rint_15:1; - uint64_t reserved_13_14:2; - uint64_t pow:1; - uint64_t tim:1; - uint64_t pko:1; - uint64_t ipd:1; - uint64_t rint_8:1; - uint64_t zip:1; - uint64_t dfa:1; - uint64_t fpa:1; - uint64_t key:1; - uint64_t npi:1; - uint64_t gmx1:1; - uint64_t gmx0:1; - uint64_t mio:1; - } s; - struct cvmx_npi_rsl_int_blocks_cn30xx { - uint64_t reserved_32_63:32; - uint64_t rint_31:1; - uint64_t iob:1; - uint64_t rint_29:1; - uint64_t rint_28:1; - uint64_t rint_27:1; - uint64_t rint_26:1; - uint64_t rint_25:1; - uint64_t rint_24:1; - uint64_t asx1:1; - uint64_t asx0:1; - uint64_t rint_21:1; - uint64_t pip:1; - uint64_t spx1:1; - uint64_t spx0:1; - uint64_t lmc:1; - uint64_t l2c:1; - uint64_t rint_15:1; - uint64_t rint_14:1; - uint64_t usb:1; - uint64_t pow:1; - uint64_t tim:1; - uint64_t pko:1; - uint64_t ipd:1; - uint64_t rint_8:1; - uint64_t zip:1; - uint64_t dfa:1; - uint64_t fpa:1; - uint64_t key:1; - uint64_t npi:1; - uint64_t gmx1:1; - uint64_t gmx0:1; - uint64_t mio:1; - } cn30xx; - struct cvmx_npi_rsl_int_blocks_cn38xx { - uint64_t reserved_32_63:32; - uint64_t rint_31:1; - uint64_t iob:1; - uint64_t rint_29:1; - uint64_t rint_28:1; - uint64_t rint_27:1; - uint64_t rint_26:1; - uint64_t rint_25:1; - uint64_t rint_24:1; - uint64_t asx1:1; - uint64_t asx0:1; - uint64_t rint_21:1; - uint64_t pip:1; - uint64_t spx1:1; - uint64_t spx0:1; - uint64_t lmc:1; - uint64_t l2c:1; - uint64_t rint_15:1; - uint64_t rint_14:1; - uint64_t rint_13:1; - uint64_t pow:1; - uint64_t tim:1; - uint64_t pko:1; - uint64_t ipd:1; - uint64_t rint_8:1; - uint64_t zip:1; - uint64_t dfa:1; - uint64_t fpa:1; - uint64_t key:1; - uint64_t npi:1; - uint64_t gmx1:1; - uint64_t gmx0:1; - uint64_t mio:1; - } cn38xx; - struct cvmx_npi_rsl_int_blocks_cn50xx { - uint64_t reserved_31_63:33; - uint64_t iob:1; - uint64_t lmc1:1; - uint64_t agl:1; - uint64_t reserved_24_27:4; - uint64_t asx1:1; - uint64_t asx0:1; - uint64_t reserved_21_21:1; - uint64_t pip:1; - uint64_t spx1:1; - uint64_t spx0:1; - uint64_t lmc:1; - uint64_t l2c:1; - uint64_t reserved_15_15:1; - uint64_t rad:1; - uint64_t usb:1; - uint64_t pow:1; - uint64_t tim:1; - uint64_t pko:1; - uint64_t ipd:1; - uint64_t reserved_8_8:1; - uint64_t zip:1; - uint64_t dfa:1; - uint64_t fpa:1; - uint64_t key:1; - uint64_t npi:1; - uint64_t gmx1:1; - uint64_t gmx0:1; - uint64_t mio:1; - } cn50xx; -}; - -union cvmx_pko_command_word0 { - uint64_t u64; - struct { - uint64_t total_bytes:16; - uint64_t segs:6; - uint64_t dontfree:1; - uint64_t ignore_i:1; - uint64_t ipoffp1:7; - uint64_t gather:1; - uint64_t rsp:1; - uint64_t wqp:1; - uint64_t n2:1; - uint64_t le:1; - uint64_t reg0:11; - uint64_t subone0:1; - uint64_t reg1:11; - uint64_t subone1:1; - uint64_t size0:2; - uint64_t size1:2; - } s; -}; - -union cvmx_ciu_timx { - uint64_t u64; - struct cvmx_ciu_timx_s { - uint64_t reserved_37_63:27; - uint64_t one_shot:1; - uint64_t len:36; - } s; -}; - -union cvmx_gmxx_rxx_rx_inbnd { - uint64_t u64; - struct cvmx_gmxx_rxx_rx_inbnd_s { - uint64_t status:1; - uint64_t speed:2; - uint64_t duplex:1; - uint64_t reserved_4_63:60; - } s; -}; - -static inline int32_t cvmx_fau_fetch_and_add32(enum cvmx_fau_reg_32 reg, - int32_t value) -{ - return value; -} - -static inline void cvmx_fau_atomic_add32(enum cvmx_fau_reg_32 reg, - int32_t value) -{ } - -static inline void cvmx_fau_atomic_write32(enum cvmx_fau_reg_32 reg, - int32_t value) -{ } - -static inline uint64_t cvmx_scratch_read64(uint64_t address) -{ - return 0; -} - -static inline void cvmx_scratch_write64(uint64_t address, uint64_t value) -{ } - -static inline int cvmx_wqe_get_grp(struct cvmx_wqe *work) -{ - return 0; -} - -static inline void *cvmx_phys_to_ptr(uint64_t physical_address) -{ - return (void *)(uintptr_t)(physical_address); -} - -static inline uint64_t cvmx_ptr_to_phys(void *ptr) -{ - return (unsigned long)ptr; -} - -static inline int cvmx_helper_get_interface_num(int ipd_port) -{ - return ipd_port; -} - -static inline int cvmx_helper_get_interface_index_num(int ipd_port) -{ - return ipd_port; -} - -static inline void cvmx_fpa_enable(void) -{ } - -static inline uint64_t cvmx_read_csr(uint64_t csr_addr) -{ - return 0; -} - -static inline void cvmx_write_csr(uint64_t csr_addr, uint64_t val) -{ } - -static inline int cvmx_helper_setup_red(int pass_thresh, int drop_thresh) -{ - return 0; -} - -static inline void *cvmx_fpa_alloc(uint64_t pool) -{ - return NULL; -} - -static inline void cvmx_fpa_free(void *ptr, uint64_t pool, - uint64_t num_cache_lines) -{ } - -static inline int octeon_is_simulation(void) -{ - return 1; -} - -static inline void cvmx_pip_get_port_status(uint64_t port_num, uint64_t clear, - cvmx_pip_port_status_t *status) -{ } - -static inline void cvmx_pko_get_port_status(uint64_t port_num, uint64_t clear, - cvmx_pko_port_status_t *status) -{ } - -static inline cvmx_helper_interface_mode_t cvmx_helper_interface_get_mode(int - interface) -{ - return 0; -} - -static inline union cvmx_helper_link_info cvmx_helper_link_get(int ipd_port) -{ - union cvmx_helper_link_info ret = { .u64 = 0 }; - - return ret; -} - -static inline int cvmx_helper_link_set(int ipd_port, - union cvmx_helper_link_info link_info) -{ - return 0; -} - -static inline int cvmx_helper_initialize_packet_io_global(void) -{ - return 0; -} - -static inline int cvmx_helper_get_number_of_interfaces(void) -{ - return 2; -} - -static inline int cvmx_helper_ports_on_interface(int interface) -{ - return 1; -} - -static inline int cvmx_helper_get_ipd_port(int interface, int port) -{ - return 0; -} - -static inline int cvmx_helper_ipd_and_packet_input_enable(void) -{ - return 0; -} - -static inline void cvmx_ipd_disable(void) -{ } - -static inline void cvmx_ipd_free_ptr(void) -{ } - -static inline void cvmx_pko_disable(void) -{ } - -static inline void cvmx_pko_shutdown(void) -{ } - -static inline int cvmx_pko_get_base_queue_per_core(int port, int core) -{ - return port; -} - -static inline int cvmx_pko_get_base_queue(int port) -{ - return port; -} - -static inline int cvmx_pko_get_num_queues(int port) -{ - return port; -} - -static inline unsigned int cvmx_get_core_num(void) -{ - return 0; -} - -static inline void cvmx_pow_work_request_async_nocheck(int scr_addr, - cvmx_pow_wait_t wait) -{ } - -static inline void cvmx_pow_work_request_async(int scr_addr, - cvmx_pow_wait_t wait) -{ } - -static inline struct cvmx_wqe *cvmx_pow_work_response_async(int scr_addr) -{ - struct cvmx_wqe *wqe = (void *)(unsigned long)scr_addr; - - return wqe; -} - -static inline struct cvmx_wqe *cvmx_pow_work_request_sync(cvmx_pow_wait_t wait) -{ - return (void *)(unsigned long)wait; -} - -static inline int cvmx_spi_restart_interface(int interface, - cvmx_spi_mode_t mode, int timeout) -{ - return 0; -} - -static inline void cvmx_fau_async_fetch_and_add32(uint64_t scraddr, - enum cvmx_fau_reg_32 reg, - int32_t value) -{ } - -static inline union cvmx_gmxx_rxx_rx_inbnd cvmx_spi4000_check_speed( - int interface, - int port) -{ - union cvmx_gmxx_rxx_rx_inbnd r; - - r.u64 = 0; - return r; -} - -static inline void cvmx_pko_send_packet_prepare(uint64_t port, uint64_t queue, - cvmx_pko_lock_t use_locking) -{ } - -static inline cvmx_pko_status_t cvmx_pko_send_packet_finish(uint64_t port, - uint64_t queue, union cvmx_pko_command_word0 pko_command, - union cvmx_buf_ptr packet, cvmx_pko_lock_t use_locking) -{ - return 0; -} - -static inline void cvmx_wqe_set_port(struct cvmx_wqe *work, int port) -{ } - -static inline void cvmx_wqe_set_qos(struct cvmx_wqe *work, int qos) -{ } - -static inline int cvmx_wqe_get_qos(struct cvmx_wqe *work) -{ - return 0; -} - -static inline void cvmx_wqe_set_grp(struct cvmx_wqe *work, int grp) -{ } - -static inline void cvmx_pow_work_submit(struct cvmx_wqe *wqp, uint32_t tag, - enum cvmx_pow_tag_type tag_type, - uint64_t qos, uint64_t grp) -{ } - -#define CVMX_ASXX_RX_CLK_SETX(a, b) ((a)+(b)) -#define CVMX_ASXX_TX_CLK_SETX(a, b) ((a)+(b)) -#define CVMX_CIU_TIMX(a) (a) -#define CVMX_GMXX_RXX_ADR_CAM0(a, b) ((a)+(b)) -#define CVMX_GMXX_RXX_ADR_CAM1(a, b) ((a)+(b)) -#define CVMX_GMXX_RXX_ADR_CAM2(a, b) ((a)+(b)) -#define CVMX_GMXX_RXX_ADR_CAM3(a, b) ((a)+(b)) -#define CVMX_GMXX_RXX_ADR_CAM4(a, b) ((a)+(b)) -#define CVMX_GMXX_RXX_ADR_CAM5(a, b) ((a)+(b)) -#define CVMX_GMXX_RXX_FRM_CTL(a, b) ((a)+(b)) -#define CVMX_GMXX_RXX_INT_REG(a, b) ((a)+(b)) -#define CVMX_GMXX_SMACX(a, b) ((a)+(b)) -#define CVMX_PIP_PRT_TAGX(a) (a) -#define CVMX_POW_PP_GRP_MSKX(a) (a) -#define CVMX_POW_WQ_INT_THRX(a) (a) -#define CVMX_SPXX_INT_MSK(a) (a) -#define CVMX_SPXX_INT_REG(a) (a) -#define CVMX_SSO_PPX_GRP_MSK(a) (a) -#define CVMX_SSO_WQ_INT_THRX(a) (a) -#define CVMX_STXX_INT_MSK(a) (a) -#define CVMX_STXX_INT_REG(a) (a) diff --git a/drivers/staging/qlge/qlge.h b/drivers/staging/qlge/qlge.h index 6ec7e3ce3863..4bc5d5fce9bf 100644 --- a/drivers/staging/qlge/qlge.h +++ b/drivers/staging/qlge/qlge.h @@ -63,7 +63,6 @@ #define UDELAY_COUNT 3 #define UDELAY_DELAY 100 - #define TX_DESC_PER_IOCB 8 #if ((MAX_SKB_FRAGS - TX_DESC_PER_IOCB) + 2) > 0 @@ -1627,18 +1626,18 @@ enum { #define MPI_COREDUMP_COOKIE 0x5555aaaa struct mpi_coredump_global_header { u32 cookie; - u8 idString[16]; - u32 timeLo; - u32 timeHi; - u32 imageSize; - u32 headerSize; + u8 id_string[16]; + u32 time_lo; + u32 time_hi; + u32 image_size; + u32 header_size; u8 info[220]; }; struct mpi_coredump_segment_header { u32 cookie; - u32 segNum; - u32 segSize; + u32 seg_num; + u32 seg_size; u32 extra; u8 description[16]; }; diff --git a/drivers/staging/qlge/qlge_dbg.c b/drivers/staging/qlge/qlge_dbg.c index 83f34ca43aa4..8cf39615c520 100644 --- a/drivers/staging/qlge/qlge_dbg.c +++ b/drivers/staging/qlge/qlge_dbg.c @@ -142,10 +142,10 @@ static int ql_get_serdes_regs(struct ql_adapter *qdev, u32 *direct_ptr, temp; u32 *indirect_ptr; - /* The XAUI needs to be read out per port */ status = ql_read_other_func_serdes_reg(qdev, - XG_SERDES_XAUI_HSS_PCS_START, &temp); + XG_SERDES_XAUI_HSS_PCS_START, + &temp); if (status) temp = XG_SERDES_ADDR_XAUI_PWR_DOWN; @@ -297,7 +297,6 @@ static int ql_get_serdes_regs(struct ql_adapter *qdev, ql_get_both_serdes(qdev, i, direct_ptr, indirect_ptr, xfi_direct_valid, xfi_indirect_valid); - /* Get XAUI_XFI_HSS_PLL register block. */ if (qdev->func & 1) { direct_ptr = @@ -482,7 +481,8 @@ static int ql_get_mpi_shadow_regs(struct ql_adapter *qdev, u32 *buf) int status; for (i = 0; i < MPI_CORE_SH_REGS_CNT; i++, buf++) { - status = ql_write_mpi_reg(qdev, RISC_124, + status = ql_write_mpi_reg(qdev, + RISC_124, (SHADOW_OFFSET | i << SHADOW_REG_SHIFT)); if (status) goto end; @@ -702,8 +702,8 @@ static void ql_build_coredump_seg_header( { memset(seg_hdr, 0, sizeof(struct mpi_coredump_segment_header)); seg_hdr->cookie = MPI_COREDUMP_COOKIE; - seg_hdr->segNum = seg_number; - seg_hdr->segSize = seg_size; + seg_hdr->seg_num = seg_number; + seg_hdr->seg_size = seg_size; strncpy(seg_hdr->description, desc, (sizeof(seg_hdr->description)) - 1); } @@ -741,12 +741,12 @@ int ql_core_dump(struct ql_adapter *qdev, struct ql_mpi_coredump *mpi_coredump) memset(&(mpi_coredump->mpi_global_header), 0, sizeof(struct mpi_coredump_global_header)); mpi_coredump->mpi_global_header.cookie = MPI_COREDUMP_COOKIE; - mpi_coredump->mpi_global_header.headerSize = + mpi_coredump->mpi_global_header.header_size = sizeof(struct mpi_coredump_global_header); - mpi_coredump->mpi_global_header.imageSize = + mpi_coredump->mpi_global_header.image_size = sizeof(struct ql_mpi_coredump); - strncpy(mpi_coredump->mpi_global_header.idString, "MPI Coredump", - sizeof(mpi_coredump->mpi_global_header.idString)); + strncpy(mpi_coredump->mpi_global_header.id_string, "MPI Coredump", + sizeof(mpi_coredump->mpi_global_header.id_string)); /* Get generic NIC reg dump */ ql_build_coredump_seg_header(&mpi_coredump->nic_regs_seg_hdr, @@ -1108,7 +1108,7 @@ int ql_core_dump(struct ql_adapter *qdev, struct ql_mpi_coredump *mpi_coredump) + sizeof(mpi_coredump->nic_routing_words), "Routing Words"); status = ql_get_routing_entries(qdev, - &mpi_coredump->nic_routing_words[0]); + &mpi_coredump->nic_routing_words[0]); if (status) goto err; @@ -1227,17 +1227,15 @@ static void ql_gen_reg_dump(struct ql_adapter *qdev, { int i, status; - memset(&(mpi_coredump->mpi_global_header), 0, sizeof(struct mpi_coredump_global_header)); mpi_coredump->mpi_global_header.cookie = MPI_COREDUMP_COOKIE; - mpi_coredump->mpi_global_header.headerSize = + mpi_coredump->mpi_global_header.header_size = sizeof(struct mpi_coredump_global_header); - mpi_coredump->mpi_global_header.imageSize = + mpi_coredump->mpi_global_header.image_size = sizeof(struct ql_reg_dump); - strncpy(mpi_coredump->mpi_global_header.idString, "MPI Coredump", - sizeof(mpi_coredump->mpi_global_header.idString)); - + strncpy(mpi_coredump->mpi_global_header.id_string, "MPI Coredump", + sizeof(mpi_coredump->mpi_global_header.id_string)); /* segment 16 */ ql_build_coredump_seg_header(&mpi_coredump->misc_nic_seg_hdr, diff --git a/drivers/staging/qlge/qlge_ethtool.c b/drivers/staging/qlge/qlge_ethtool.c index 56d116d79e56..790997aff995 100644 --- a/drivers/staging/qlge/qlge_ethtool.c +++ b/drivers/staging/qlge/qlge_ethtool.c @@ -32,7 +32,6 @@ #include <linux/mm.h> #include <linux/vmalloc.h> - #include "qlge.h" struct ql_stats { @@ -197,8 +196,7 @@ static int ql_update_ring_coalescing(struct ql_adapter *qdev) */ cqicb = (struct cqicb *)&qdev->rx_ring[qdev->rss_ring_count]; if (le16_to_cpu(cqicb->irq_delay) != qdev->tx_coalesce_usecs || - le16_to_cpu(cqicb->pkt_delay) != - qdev->tx_max_coalesced_frames) { + le16_to_cpu(cqicb->pkt_delay) != qdev->tx_max_coalesced_frames) { for (i = qdev->rss_ring_count; i < qdev->rx_ring_count; i++) { rx_ring = &qdev->rx_ring[i]; cqicb = (struct cqicb *)rx_ring; @@ -207,7 +205,7 @@ static int ql_update_ring_coalescing(struct ql_adapter *qdev) cpu_to_le16(qdev->tx_max_coalesced_frames); cqicb->flags = FLAGS_LI; status = ql_write_cfg(qdev, cqicb, sizeof(*cqicb), - CFG_LCQ, rx_ring->cq_id); + CFG_LCQ, rx_ring->cq_id); if (status) { netif_err(qdev, ifup, qdev->ndev, "Failed to load CQICB.\n"); @@ -219,8 +217,7 @@ static int ql_update_ring_coalescing(struct ql_adapter *qdev) /* Update the inbound (RSS) handler queues if they changed. */ cqicb = (struct cqicb *)&qdev->rx_ring[0]; if (le16_to_cpu(cqicb->irq_delay) != qdev->rx_coalesce_usecs || - le16_to_cpu(cqicb->pkt_delay) != - qdev->rx_max_coalesced_frames) { + le16_to_cpu(cqicb->pkt_delay) != qdev->rx_max_coalesced_frames) { for (i = 0; i < qdev->rss_ring_count; i++, rx_ring++) { rx_ring = &qdev->rx_ring[i]; cqicb = (struct cqicb *)rx_ring; @@ -229,7 +226,7 @@ static int ql_update_ring_coalescing(struct ql_adapter *qdev) cpu_to_le16(qdev->rx_max_coalesced_frames); cqicb->flags = FLAGS_LI; status = ql_write_cfg(qdev, cqicb, sizeof(*cqicb), - CFG_LCQ, rx_ring->cq_id); + CFG_LCQ, rx_ring->cq_id); if (status) { netif_err(qdev, ifup, qdev->ndev, "Failed to load CQICB.\n"); @@ -332,6 +329,7 @@ quit: static void ql_get_strings(struct net_device *dev, u32 stringset, u8 *buf) { int index; + switch (stringset) { case ETH_SS_TEST: memcpy(buf, *ql_gstrings_test, QLGE_TEST_LEN * ETH_GSTRING_LEN); @@ -339,8 +337,8 @@ static void ql_get_strings(struct net_device *dev, u32 stringset, u8 *buf) case ETH_SS_STATS: for (index = 0; index < QLGE_STATS_LEN; index++) { memcpy(buf + index * ETH_GSTRING_LEN, - ql_gstrings_stats[index].stat_string, - ETH_GSTRING_LEN); + ql_gstrings_stats[index].stat_string, + ETH_GSTRING_LEN); } break; } @@ -412,6 +410,7 @@ static void ql_get_drvinfo(struct net_device *ndev, struct ethtool_drvinfo *drvinfo) { struct ql_adapter *qdev = netdev_priv(ndev); + strlcpy(drvinfo->driver, qlge_driver_name, sizeof(drvinfo->driver)); strlcpy(drvinfo->version, qlge_driver_version, sizeof(drvinfo->version)); @@ -431,7 +430,7 @@ static void ql_get_wol(struct net_device *ndev, struct ethtool_wolinfo *wol) /* WOL is only supported for mezz card. */ if (ssys_dev == QLGE_MEZZ_SSYS_ID_068 || - ssys_dev == QLGE_MEZZ_SSYS_ID_180) { + ssys_dev == QLGE_MEZZ_SSYS_ID_180) { wol->supported = WAKE_MAGIC; wol->wolopts = qdev->wol; } @@ -444,9 +443,9 @@ static int ql_set_wol(struct net_device *ndev, struct ethtool_wolinfo *wol) /* WOL is only supported for mezz card. */ if (ssys_dev != QLGE_MEZZ_SSYS_ID_068 && - ssys_dev != QLGE_MEZZ_SSYS_ID_180) { + ssys_dev != QLGE_MEZZ_SSYS_ID_180) { netif_info(qdev, drv, qdev->ndev, - "WOL is only supported for mezz card\n"); + "WOL is only supported for mezz card\n"); return -EOPNOTSUPP; } if (wol->wolopts & ~WAKE_MAGIC) @@ -506,7 +505,7 @@ static void ql_stop_loopback(struct ql_adapter *qdev) } static void ql_create_lb_frame(struct sk_buff *skb, - unsigned int frame_size) + unsigned int frame_size) { memset(skb->data, 0xFF, frame_size); frame_size &= ~1; @@ -516,13 +515,13 @@ static void ql_create_lb_frame(struct sk_buff *skb, } void ql_check_lb_frame(struct ql_adapter *qdev, - struct sk_buff *skb) + struct sk_buff *skb) { unsigned int frame_size = skb->len; if ((*(skb->data + 3) == 0xFF) && - (*(skb->data + frame_size / 2 + 10) == 0xBE) && - (*(skb->data + frame_size / 2 + 12) == 0xAF)) { + (*(skb->data + frame_size / 2 + 10) == 0xBE) && + (*(skb->data + frame_size / 2 + 12) == 0xAF)) { atomic_dec(&qdev->lb_count); return; } @@ -566,7 +565,7 @@ out: } static void ql_self_test(struct net_device *ndev, - struct ethtool_test *eth_test, u64 *data) + struct ethtool_test *eth_test, u64 *data) { struct ql_adapter *qdev = netdev_priv(ndev); @@ -672,7 +671,7 @@ static int ql_set_coalesce(struct net_device *ndev, struct ethtool_coalesce *c) } static void ql_get_pauseparam(struct net_device *netdev, - struct ethtool_pauseparam *pause) + struct ethtool_pauseparam *pause) { struct ql_adapter *qdev = netdev_priv(netdev); @@ -684,7 +683,7 @@ static void ql_get_pauseparam(struct net_device *netdev, } static int ql_set_pauseparam(struct net_device *netdev, - struct ethtool_pauseparam *pause) + struct ethtool_pauseparam *pause) { struct ql_adapter *qdev = netdev_priv(netdev); int status = 0; @@ -703,12 +702,14 @@ static int ql_set_pauseparam(struct net_device *netdev, static u32 ql_get_msglevel(struct net_device *ndev) { struct ql_adapter *qdev = netdev_priv(ndev); + return qdev->msg_enable; } static void ql_set_msglevel(struct net_device *ndev, u32 value) { struct ql_adapter *qdev = netdev_priv(ndev); + qdev->msg_enable = value; } diff --git a/drivers/staging/qlge/qlge_main.c b/drivers/staging/qlge/qlge_main.c index ed5440d51332..ef8037d0b52e 100644 --- a/drivers/staging/qlge/qlge_main.c +++ b/drivers/staging/qlge/qlge_main.c @@ -77,14 +77,12 @@ MODULE_PARM_DESC(qlge_irq_type, "0 = MSI-X, 1 = MSI, 2 = Legacy."); static int qlge_mpi_coredump; module_param(qlge_mpi_coredump, int, 0); MODULE_PARM_DESC(qlge_mpi_coredump, - "Option to enable MPI firmware dump. " - "Default is OFF - Do Not allocate memory. "); + "Option to enable MPI firmware dump. Default is OFF - Do Not allocate memory. "); static int qlge_force_coredump; module_param(qlge_force_coredump, int, 0); MODULE_PARM_DESC(qlge_force_coredump, - "Option to allow force of firmware core dump. " - "Default is OFF - Do not allow."); + "Option to allow force of firmware core dump. Default is OFF - Do not allow."); static const struct pci_device_id qlge_pci_tbl[] = { {PCI_DEVICE(PCI_VENDOR_ID_QLOGIC, QLGE_DEVICE_ID_8012)}, @@ -178,8 +176,9 @@ int ql_wait_reg_rdy(struct ql_adapter *qdev, u32 reg, u32 bit, u32 err_bit) "register 0x%.08x access error, value = 0x%.08x!.\n", reg, temp); return -EIO; - } else if (temp & bit) + } else if (temp & bit) { return 0; + } udelay(UDELAY_DELAY); } netif_alert(qdev, probe, qdev->ndev, @@ -206,7 +205,6 @@ static int ql_wait_cfg(struct ql_adapter *qdev, u32 bit) return -ETIMEDOUT; } - /* Used to issue init control blocks to hw. Maps control block, * sets address, triggers download, waits for completion. */ @@ -270,36 +268,34 @@ int ql_get_mac_addr_reg(struct ql_adapter *qdev, u32 type, u16 index, { status = ql_wait_reg_rdy(qdev, - MAC_ADDR_IDX, MAC_ADDR_MW, 0); + MAC_ADDR_IDX, MAC_ADDR_MW, 0); if (status) goto exit; ql_write32(qdev, MAC_ADDR_IDX, (offset++) | /* offset */ (index << MAC_ADDR_IDX_SHIFT) | /* index */ MAC_ADDR_ADR | MAC_ADDR_RS | type); /* type */ status = - ql_wait_reg_rdy(qdev, - MAC_ADDR_IDX, MAC_ADDR_MR, 0); + ql_wait_reg_rdy(qdev, MAC_ADDR_IDX, MAC_ADDR_MR, 0); if (status) goto exit; *value++ = ql_read32(qdev, MAC_ADDR_DATA); status = - ql_wait_reg_rdy(qdev, - MAC_ADDR_IDX, MAC_ADDR_MW, 0); + ql_wait_reg_rdy(qdev, MAC_ADDR_IDX, MAC_ADDR_MW, 0); if (status) goto exit; ql_write32(qdev, MAC_ADDR_IDX, (offset++) | /* offset */ (index << MAC_ADDR_IDX_SHIFT) | /* index */ MAC_ADDR_ADR | MAC_ADDR_RS | type); /* type */ status = - ql_wait_reg_rdy(qdev, - MAC_ADDR_IDX, MAC_ADDR_MR, 0); + ql_wait_reg_rdy(qdev, MAC_ADDR_IDX, MAC_ADDR_MR, 0); if (status) goto exit; *value++ = ql_read32(qdev, MAC_ADDR_DATA); if (type == MAC_ADDR_TYPE_CAM_MAC) { status = ql_wait_reg_rdy(qdev, - MAC_ADDR_IDX, MAC_ADDR_MW, 0); + MAC_ADDR_IDX, MAC_ADDR_MW, + 0); if (status) goto exit; ql_write32(qdev, MAC_ADDR_IDX, (offset++) | /* offset */ @@ -343,7 +339,7 @@ static int ql_set_mac_addr_reg(struct ql_adapter *qdev, u8 *addr, u32 type, status = ql_wait_reg_rdy(qdev, - MAC_ADDR_IDX, MAC_ADDR_MW, 0); + MAC_ADDR_IDX, MAC_ADDR_MW, 0); if (status) goto exit; ql_write32(qdev, MAC_ADDR_IDX, (offset++) | @@ -352,7 +348,7 @@ static int ql_set_mac_addr_reg(struct ql_adapter *qdev, u8 *addr, u32 type, ql_write32(qdev, MAC_ADDR_DATA, lower); status = ql_wait_reg_rdy(qdev, - MAC_ADDR_IDX, MAC_ADDR_MW, 0); + MAC_ADDR_IDX, MAC_ADDR_MW, 0); if (status) goto exit; ql_write32(qdev, MAC_ADDR_IDX, (offset++) | @@ -362,7 +358,7 @@ static int ql_set_mac_addr_reg(struct ql_adapter *qdev, u8 *addr, u32 type, ql_write32(qdev, MAC_ADDR_DATA, upper); status = ql_wait_reg_rdy(qdev, - MAC_ADDR_IDX, MAC_ADDR_MW, 0); + MAC_ADDR_IDX, MAC_ADDR_MW, 0); if (status) goto exit; break; @@ -375,8 +371,7 @@ static int ql_set_mac_addr_reg(struct ql_adapter *qdev, u8 *addr, u32 type, (addr[2] << 24) | (addr[3] << 16) | (addr[4] << 8) | (addr[5]); status = - ql_wait_reg_rdy(qdev, - MAC_ADDR_IDX, MAC_ADDR_MW, 0); + ql_wait_reg_rdy(qdev, MAC_ADDR_IDX, MAC_ADDR_MW, 0); if (status) goto exit; ql_write32(qdev, MAC_ADDR_IDX, (offset++) | /* offset */ @@ -384,8 +379,7 @@ static int ql_set_mac_addr_reg(struct ql_adapter *qdev, u8 *addr, u32 type, type); /* type */ ql_write32(qdev, MAC_ADDR_DATA, lower); status = - ql_wait_reg_rdy(qdev, - MAC_ADDR_IDX, MAC_ADDR_MW, 0); + ql_wait_reg_rdy(qdev, MAC_ADDR_IDX, MAC_ADDR_MW, 0); if (status) goto exit; ql_write32(qdev, MAC_ADDR_IDX, (offset++) | /* offset */ @@ -393,16 +387,15 @@ static int ql_set_mac_addr_reg(struct ql_adapter *qdev, u8 *addr, u32 type, type); /* type */ ql_write32(qdev, MAC_ADDR_DATA, upper); status = - ql_wait_reg_rdy(qdev, - MAC_ADDR_IDX, MAC_ADDR_MW, 0); + ql_wait_reg_rdy(qdev, MAC_ADDR_IDX, MAC_ADDR_MW, 0); if (status) goto exit; ql_write32(qdev, MAC_ADDR_IDX, (offset) | /* offset */ (index << MAC_ADDR_IDX_SHIFT) | /* index */ type); /* type */ /* This field should also include the queue id - and possibly the function id. Right now we hardcode - the route field to NIC core. + * and possibly the function id. Right now we hardcode + * the route field to NIC core. */ cam_output = (CAM_OUT_ROUTE_NIC | (qdev-> @@ -423,8 +416,7 @@ static int ql_set_mac_addr_reg(struct ql_adapter *qdev, u8 *addr, u32 type, * That's bit-27 we're talking about. */ status = - ql_wait_reg_rdy(qdev, - MAC_ADDR_IDX, MAC_ADDR_MW, 0); + ql_wait_reg_rdy(qdev, MAC_ADDR_IDX, MAC_ADDR_MW, 0); if (status) goto exit; ql_write32(qdev, MAC_ADDR_IDX, offset | /* offset */ @@ -467,7 +459,8 @@ static int ql_set_mac_addr(struct ql_adapter *qdev, int set) if (status) return status; status = ql_set_mac_addr_reg(qdev, (u8 *) addr, - MAC_ADDR_TYPE_CAM_MAC, qdev->func * MAX_CQ); + MAC_ADDR_TYPE_CAM_MAC, + qdev->func * MAX_CQ); ql_sem_unlock(qdev, SEM_MAC_ADDR_MASK); if (status) netif_err(qdev, ifup, qdev->ndev, @@ -672,17 +665,17 @@ static int ql_read_flash_word(struct ql_adapter *qdev, int offset, __le32 *data) int status = 0; /* wait for reg to come ready */ status = ql_wait_reg_rdy(qdev, - FLASH_ADDR, FLASH_ADDR_RDY, FLASH_ADDR_ERR); + FLASH_ADDR, FLASH_ADDR_RDY, FLASH_ADDR_ERR); if (status) goto exit; /* set up for reg read */ ql_write32(qdev, FLASH_ADDR, FLASH_ADDR_R | offset); /* wait for reg to come ready */ status = ql_wait_reg_rdy(qdev, - FLASH_ADDR, FLASH_ADDR_RDY, FLASH_ADDR_ERR); + FLASH_ADDR, FLASH_ADDR_RDY, FLASH_ADDR_ERR); if (status) goto exit; - /* This data is stored on flash as an array of + /* This data is stored on flash as an array of * __le32. Since ql_read32() returns cpu endian * we need to swap it back. */ @@ -721,8 +714,9 @@ static int ql_get_8000_flash_params(struct ql_adapter *qdev) } status = ql_validate_flash(qdev, - sizeof(struct flash_params_8000) / sizeof(u16), - "8000"); + sizeof(struct flash_params_8000) / + sizeof(u16), + "8000"); if (status) { netif_err(qdev, ifup, qdev->ndev, "Invalid flash.\n"); status = -EINVAL; @@ -734,12 +728,12 @@ static int ql_get_8000_flash_params(struct ql_adapter *qdev) */ if (qdev->flash.flash_params_8000.data_type1 == 2) memcpy(mac_addr, - qdev->flash.flash_params_8000.mac_addr1, - qdev->ndev->addr_len); + qdev->flash.flash_params_8000.mac_addr1, + qdev->ndev->addr_len); else memcpy(mac_addr, - qdev->flash.flash_params_8000.mac_addr, - qdev->ndev->addr_len); + qdev->flash.flash_params_8000.mac_addr, + qdev->ndev->addr_len); if (!is_valid_ether_addr(mac_addr)) { netif_err(qdev, ifup, qdev->ndev, "Invalid MAC address.\n"); @@ -748,8 +742,8 @@ static int ql_get_8000_flash_params(struct ql_adapter *qdev) } memcpy(qdev->ndev->dev_addr, - mac_addr, - qdev->ndev->addr_len); + mac_addr, + qdev->ndev->addr_len); exit: ql_sem_unlock(qdev, SEM_FLASH_MASK); @@ -784,8 +778,9 @@ static int ql_get_8012_flash_params(struct ql_adapter *qdev) } status = ql_validate_flash(qdev, - sizeof(struct flash_params_8012) / sizeof(u16), - "8012"); + sizeof(struct flash_params_8012) / + sizeof(u16), + "8012"); if (status) { netif_err(qdev, ifup, qdev->ndev, "Invalid flash.\n"); status = -EINVAL; @@ -798,8 +793,8 @@ static int ql_get_8012_flash_params(struct ql_adapter *qdev) } memcpy(qdev->ndev->dev_addr, - qdev->flash.flash_params_8012.mac_addr, - qdev->ndev->addr_len); + qdev->flash.flash_params_8012.mac_addr, + qdev->ndev->addr_len); exit: ql_sem_unlock(qdev, SEM_FLASH_MASK); @@ -815,7 +810,7 @@ static int ql_write_xgmac_reg(struct ql_adapter *qdev, u32 reg, u32 data) int status; /* wait for reg to come ready */ status = ql_wait_reg_rdy(qdev, - XGMAC_ADDR, XGMAC_ADDR_RDY, XGMAC_ADDR_XME); + XGMAC_ADDR, XGMAC_ADDR_RDY, XGMAC_ADDR_XME); if (status) return status; /* write the data to the data reg */ @@ -834,14 +829,14 @@ int ql_read_xgmac_reg(struct ql_adapter *qdev, u32 reg, u32 *data) int status = 0; /* wait for reg to come ready */ status = ql_wait_reg_rdy(qdev, - XGMAC_ADDR, XGMAC_ADDR_RDY, XGMAC_ADDR_XME); + XGMAC_ADDR, XGMAC_ADDR_RDY, XGMAC_ADDR_XME); if (status) goto exit; /* set up for reg read */ ql_write32(qdev, XGMAC_ADDR, reg | XGMAC_ADDR_R); /* wait for reg to come ready */ status = ql_wait_reg_rdy(qdev, - XGMAC_ADDR, XGMAC_ADDR_RDY, XGMAC_ADDR_XME); + XGMAC_ADDR, XGMAC_ADDR_RDY, XGMAC_ADDR_XME); if (status) goto exit; /* get the data */ @@ -1436,10 +1431,9 @@ static void ql_update_mac_hdr_len(struct ql_adapter *qdev, /* Process an inbound completion from an rx ring. */ static void ql_process_mac_rx_gro_page(struct ql_adapter *qdev, - struct rx_ring *rx_ring, - struct ib_mac_iocb_rsp *ib_mac_rsp, - u32 length, - u16 vlan_id) + struct rx_ring *rx_ring, + struct ib_mac_iocb_rsp *ib_mac_rsp, + u32 length, u16 vlan_id) { struct sk_buff *skb; struct qlge_bq_desc *lbq_desc = ql_get_curr_lchunk(qdev, rx_ring); @@ -1483,10 +1477,9 @@ static void ql_process_mac_rx_gro_page(struct ql_adapter *qdev, /* Process an inbound completion from an rx ring. */ static void ql_process_mac_rx_page(struct ql_adapter *qdev, - struct rx_ring *rx_ring, - struct ib_mac_iocb_rsp *ib_mac_rsp, - u32 length, - u16 vlan_id) + struct rx_ring *rx_ring, + struct ib_mac_iocb_rsp *ib_mac_rsp, + u32 length, u16 vlan_id) { struct net_device *ndev = qdev->ndev; struct sk_buff *skb = NULL; @@ -1528,8 +1521,7 @@ static void ql_process_mac_rx_page(struct ql_adapter *qdev, "%d bytes of headers and data in large. Chain page to new skb and pull tail.\n", length); skb_fill_page_desc(skb, 0, lbq_desc->p.pg_chunk.page, - lbq_desc->p.pg_chunk.offset + hlen, - length - hlen); + lbq_desc->p.pg_chunk.offset + hlen, length - hlen); skb->len += length - hlen; skb->data_len += length - hlen; skb->truesize += length - hlen; @@ -1540,7 +1532,7 @@ static void ql_process_mac_rx_page(struct ql_adapter *qdev, skb_checksum_none_assert(skb); if ((ndev->features & NETIF_F_RXCSUM) && - !(ib_mac_rsp->flags1 & IB_MAC_CSUM_ERR_MASK)) { + !(ib_mac_rsp->flags1 & IB_MAC_CSUM_ERR_MASK)) { /* TCP frame. */ if (ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_T) { netif_printk(qdev, rx_status, KERN_DEBUG, qdev->ndev, @@ -1576,10 +1568,9 @@ err_out: /* Process an inbound completion from an rx ring. */ static void ql_process_mac_rx_skb(struct ql_adapter *qdev, - struct rx_ring *rx_ring, - struct ib_mac_iocb_rsp *ib_mac_rsp, - u32 length, - u16 vlan_id) + struct rx_ring *rx_ring, + struct ib_mac_iocb_rsp *ib_mac_rsp, + u32 length, u16 vlan_id) { struct qlge_bq_desc *sbq_desc = qlge_get_curr_buf(&rx_ring->sbq); struct net_device *ndev = qdev->ndev; @@ -1648,7 +1639,7 @@ static void ql_process_mac_rx_skb(struct ql_adapter *qdev, * csum or frame errors. */ if ((ndev->features & NETIF_F_RXCSUM) && - !(ib_mac_rsp->flags1 & IB_MAC_CSUM_ERR_MASK)) { + !(ib_mac_rsp->flags1 & IB_MAC_CSUM_ERR_MASK)) { /* TCP frame. */ if (ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_T) { netif_printk(qdev, rx_status, KERN_DEBUG, qdev->ndev, @@ -1779,8 +1770,7 @@ static struct sk_buff *ql_build_rx_skb(struct ql_adapter *qdev, "Chaining page at offset = %d, for %d bytes to skb.\n", lbq_desc->p.pg_chunk.offset, length); skb_fill_page_desc(skb, 0, lbq_desc->p.pg_chunk.page, - lbq_desc->p.pg_chunk.offset, - length); + lbq_desc->p.pg_chunk.offset, length); skb->len += length; skb->data_len += length; skb->truesize += length; @@ -1804,10 +1794,9 @@ static struct sk_buff *ql_build_rx_skb(struct ql_adapter *qdev, netif_printk(qdev, rx_status, KERN_DEBUG, qdev->ndev, "%d bytes of headers and data in large. Chain page to new skb and pull tail.\n", length); - skb_fill_page_desc(skb, 0, - lbq_desc->p.pg_chunk.page, - lbq_desc->p.pg_chunk.offset, - length); + skb_fill_page_desc(skb, 0, lbq_desc->p.pg_chunk.page, + lbq_desc->p.pg_chunk.offset, + length); skb->len += length; skb->data_len += length; skb->truesize += length; @@ -1857,9 +1846,8 @@ static struct sk_buff *ql_build_rx_skb(struct ql_adapter *qdev, "Adding page %d to skb for %d bytes.\n", i, size); skb_fill_page_desc(skb, i, - lbq_desc->p.pg_chunk.page, - lbq_desc->p.pg_chunk.offset, - size); + lbq_desc->p.pg_chunk.page, + lbq_desc->p.pg_chunk.offset, size); skb->len += size; skb->data_len += size; skb->truesize += size; @@ -1875,9 +1863,9 @@ static struct sk_buff *ql_build_rx_skb(struct ql_adapter *qdev, /* Process an inbound completion from an rx ring. */ static void ql_process_mac_split_rx_intr(struct ql_adapter *qdev, - struct rx_ring *rx_ring, - struct ib_mac_iocb_rsp *ib_mac_rsp, - u16 vlan_id) + struct rx_ring *rx_ring, + struct ib_mac_iocb_rsp *ib_mac_rsp, + u16 vlan_id) { struct net_device *ndev = qdev->ndev; struct sk_buff *skb = NULL; @@ -1938,7 +1926,7 @@ static void ql_process_mac_split_rx_intr(struct ql_adapter *qdev, * csum or frame errors. */ if ((ndev->features & NETIF_F_RXCSUM) && - !(ib_mac_rsp->flags1 & IB_MAC_CSUM_ERR_MASK)) { + !(ib_mac_rsp->flags1 & IB_MAC_CSUM_ERR_MASK)) { /* TCP frame. */ if (ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_T) { netif_printk(qdev, rx_status, KERN_DEBUG, qdev->ndev, @@ -1970,8 +1958,8 @@ static void ql_process_mac_split_rx_intr(struct ql_adapter *qdev, /* Process an inbound completion from an rx ring. */ static unsigned long ql_process_mac_rx_intr(struct ql_adapter *qdev, - struct rx_ring *rx_ring, - struct ib_mac_iocb_rsp *ib_mac_rsp) + struct rx_ring *rx_ring, + struct ib_mac_iocb_rsp *ib_mac_rsp) { u32 length = le32_to_cpu(ib_mac_rsp->data_len); u16 vlan_id = ((ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_V) && @@ -1986,34 +1974,34 @@ static unsigned long ql_process_mac_rx_intr(struct ql_adapter *qdev, * separate buffers. */ ql_process_mac_split_rx_intr(qdev, rx_ring, ib_mac_rsp, - vlan_id); + vlan_id); } else if (ib_mac_rsp->flags3 & IB_MAC_IOCB_RSP_DS) { /* The data fit in a single small buffer. * Allocate a new skb, copy the data and * return the buffer to the free pool. */ - ql_process_mac_rx_skb(qdev, rx_ring, ib_mac_rsp, - length, vlan_id); + ql_process_mac_rx_skb(qdev, rx_ring, ib_mac_rsp, length, + vlan_id); } else if ((ib_mac_rsp->flags3 & IB_MAC_IOCB_RSP_DL) && !(ib_mac_rsp->flags1 & IB_MAC_CSUM_ERR_MASK) && (ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_T)) { /* TCP packet in a page chunk that's been checksummed. * Tack it on to our GRO skb and let it go. */ - ql_process_mac_rx_gro_page(qdev, rx_ring, ib_mac_rsp, - length, vlan_id); + ql_process_mac_rx_gro_page(qdev, rx_ring, ib_mac_rsp, length, + vlan_id); } else if (ib_mac_rsp->flags3 & IB_MAC_IOCB_RSP_DL) { /* Non-TCP packet in a page chunk. Allocate an * skb, tack it on frags, and send it up. */ - ql_process_mac_rx_page(qdev, rx_ring, ib_mac_rsp, - length, vlan_id); + ql_process_mac_rx_page(qdev, rx_ring, ib_mac_rsp, length, + vlan_id); } else { /* Non-TCP/UDP large frames that span multiple buffers * can be processed corrrectly by the split frame logic. */ ql_process_mac_split_rx_intr(qdev, rx_ring, ib_mac_rsp, - vlan_id); + vlan_id); } return (unsigned long)length; @@ -2222,15 +2210,16 @@ static int ql_napi_poll_msix(struct napi_struct *napi, int budget) "Enter, NAPI POLL cq_id = %d.\n", rx_ring->cq_id); /* Service the TX rings first. They start - * right after the RSS rings. */ + * right after the RSS rings. + */ for (i = qdev->rss_ring_count; i < qdev->rx_ring_count; i++) { trx_ring = &qdev->rx_ring[i]; /* If this TX completion ring belongs to this vector and * it's not empty then service it. */ if ((ctx->irq_mask & (1 << trx_ring->cq_id)) && - (ql_read_sh_reg(trx_ring->prod_idx_sh_reg) != - trx_ring->cnsmr_idx)) { + (ql_read_sh_reg(trx_ring->prod_idx_sh_reg) != + trx_ring->cnsmr_idx)) { netif_printk(qdev, intr, KERN_DEBUG, qdev->ndev, "%s: Servicing TX completion ring %d.\n", __func__, trx_ring->cq_id); @@ -2304,7 +2293,7 @@ static int qlge_update_hw_vlan_features(struct net_device *ndev, } static int qlge_set_features(struct net_device *ndev, - netdev_features_t features) + netdev_features_t features) { netdev_features_t changed = ndev->features ^ features; int err; @@ -2447,7 +2436,7 @@ static irqreturn_t qlge_isr(int irq, void *dev_id) * Check MPI processor activity. */ if ((var & STS_PI) && - (ql_read32(qdev, INTR_MASK) & INTR_MASK_PI)) { + (ql_read32(qdev, INTR_MASK) & INTR_MASK_PI)) { /* * We've got an async event or mailbox completion. * Handle it and clear the source of the interrupt. @@ -2456,7 +2445,7 @@ static irqreturn_t qlge_isr(int irq, void *dev_id) "Got MPI processor interrupt.\n"); ql_write32(qdev, INTR_MASK, (INTR_MASK_PI << 16)); queue_delayed_work_on(smp_processor_id(), - qdev->workqueue, &qdev->mpi_work, 0); + qdev->workqueue, &qdev->mpi_work, 0); work_done++; } @@ -2639,7 +2628,6 @@ static netdev_tx_t qlge_send(struct sk_buff *skb, struct net_device *ndev) return NETDEV_TX_OK; } - static void ql_free_shadow_space(struct ql_adapter *qdev) { if (qdev->rx_ring_shadow_reg_area) { @@ -2887,7 +2875,8 @@ static void ql_free_rx_resources(struct ql_adapter *qdev, } /* Allocate queues and buffers for this completions queue based - * on the values in the parameter structure. */ + * on the values in the parameter structure. + */ static int ql_alloc_rx_resources(struct ql_adapter *qdev, struct rx_ring *rx_ring) { @@ -3530,19 +3519,17 @@ static int ql_route_initialize(struct ql_adapter *qdev) return status; status = ql_set_routing_reg(qdev, RT_IDX_IP_CSUM_ERR_SLOT, - RT_IDX_IP_CSUM_ERR, 1); + RT_IDX_IP_CSUM_ERR, 1); if (status) { netif_err(qdev, ifup, qdev->ndev, - "Failed to init routing register " - "for IP CSUM error packets.\n"); + "Failed to init routing register for IP CSUM error packets.\n"); goto exit; } status = ql_set_routing_reg(qdev, RT_IDX_TCP_UDP_CSUM_ERR_SLOT, - RT_IDX_TU_CSUM_ERR, 1); + RT_IDX_TU_CSUM_ERR, 1); if (status) { netif_err(qdev, ifup, qdev->ndev, - "Failed to init routing register " - "for TCP/UDP CSUM error packets.\n"); + "Failed to init routing register for TCP/UDP CSUM error packets.\n"); goto exit; } status = ql_set_routing_reg(qdev, RT_IDX_BCAST_SLOT, RT_IDX_BCAST, 1); @@ -3556,7 +3543,7 @@ static int ql_route_initialize(struct ql_adapter *qdev) */ if (qdev->rss_ring_count > 1) { status = ql_set_routing_reg(qdev, RT_IDX_RSS_MATCH_SLOT, - RT_IDX_RSS_MATCH, 1); + RT_IDX_RSS_MATCH, 1); if (status) { netif_err(qdev, ifup, qdev->ndev, "Failed to init routing register for MATCH RSS packets.\n"); @@ -3654,7 +3641,7 @@ static int ql_adapter_initialize(struct ql_adapter *qdev) /* Default WOL is enable on Mezz cards */ if (qdev->pdev->subsystem_device == 0x0068 || - qdev->pdev->subsystem_device == 0x0180) + qdev->pdev->subsystem_device == 0x0180) qdev->wol = WAKE_MAGIC; /* Start up the rx queues. */ @@ -3731,8 +3718,9 @@ static int ql_adapter_reset(struct ql_adapter *qdev) /* Wait for the NIC and MGMNT FIFOs to empty. */ ql_wait_fifo_empty(qdev); - } else + } else { clear_bit(QL_ASIC_RECOVERY, &qdev->flags); + } ql_write32(qdev, RST_FO, (RST_FO_FR << 16) | RST_FO_FR); @@ -3880,7 +3868,7 @@ static int ql_adapter_up(struct ql_adapter *qdev) * link is up the turn on the carrier. */ if ((ql_read32(qdev, STS) & qdev->port_init) && - (ql_read32(qdev, STS) & qdev->port_link_up)) + (ql_read32(qdev, STS) & qdev->port_link_up)) ql_link_on(qdev); /* Restore rx mode. */ clear_bit(QL_ALLMULTI, &qdev->flags); @@ -4099,21 +4087,20 @@ static int qlge_change_mtu(struct net_device *ndev, int new_mtu) struct ql_adapter *qdev = netdev_priv(ndev); int status; - if (ndev->mtu == 1500 && new_mtu == 9000) { + if (ndev->mtu == 1500 && new_mtu == 9000) netif_err(qdev, ifup, qdev->ndev, "Changing to jumbo MTU.\n"); - } else if (ndev->mtu == 9000 && new_mtu == 1500) { + else if (ndev->mtu == 9000 && new_mtu == 1500) netif_err(qdev, ifup, qdev->ndev, "Changing to normal MTU.\n"); - } else + else return -EINVAL; queue_delayed_work(qdev->workqueue, - &qdev->mpi_port_cfg_work, 3*HZ); + &qdev->mpi_port_cfg_work, 3 * HZ); ndev->mtu = new_mtu; - if (!netif_running(qdev->ndev)) { + if (!netif_running(qdev->ndev)) return 0; - } status = ql_change_rx_buffers(qdev); if (status) { @@ -4267,7 +4254,8 @@ static int qlge_set_mac_address(struct net_device *ndev, void *p) if (status) return status; status = ql_set_mac_addr_reg(qdev, (u8 *) ndev->dev_addr, - MAC_ADDR_TYPE_CAM_MAC, qdev->func * MAX_CQ); + MAC_ADDR_TYPE_CAM_MAC, + qdev->func * MAX_CQ); if (status) netif_err(qdev, hw, qdev->ndev, "Failed to load MAC address.\n"); ql_sem_unlock(qdev, SEM_MAC_ADDR_MASK); @@ -4334,7 +4322,7 @@ static int ql_get_alt_pcie_func(struct ql_adapter *qdev) u32 nic_func1, nic_func2; status = ql_read_mpi_reg(qdev, MPI_TEST_FUNC_PORT_CFG, - &temp); + &temp); if (status) return status; @@ -4578,11 +4566,12 @@ static int qlge_probe(struct pci_dev *pdev, { struct net_device *ndev = NULL; struct ql_adapter *qdev = NULL; - static int cards_found = 0; + static int cards_found; int err = 0; ndev = alloc_etherdev_mq(sizeof(struct ql_adapter), - min(MAX_CPUS, netif_get_num_default_rss_queues())); + min(MAX_CPUS, + netif_get_num_default_rss_queues())); if (!ndev) return -ENOMEM; diff --git a/drivers/staging/qlge/qlge_mpi.c b/drivers/staging/qlge/qlge_mpi.c index 9e422bbbb6ab..bb03b2fa7233 100644 --- a/drivers/staging/qlge/qlge_mpi.c +++ b/drivers/staging/qlge/qlge_mpi.c @@ -134,7 +134,7 @@ static int ql_get_mb_sts(struct ql_adapter *qdev, struct mbox_params *mbcp) for (i = 0; i < mbcp->out_count; i++) { status = ql_read_mpi_reg(qdev, qdev->mailbox_out + i, - &mbcp->mbox_out[i]); + &mbcp->mbox_out[i]); if (status) { netif_err(qdev, drv, qdev->ndev, "Failed mailbox read.\n"); break; @@ -184,7 +184,7 @@ static int ql_exec_mb_cmd(struct ql_adapter *qdev, struct mbox_params *mbcp) */ for (i = 0; i < mbcp->in_count; i++) { status = ql_write_mpi_reg(qdev, qdev->mailbox_in + i, - mbcp->mbox_in[i]); + mbcp->mbox_in[i]); if (status) goto end; } @@ -293,7 +293,7 @@ static void ql_link_up(struct ql_adapter *qdev, struct mbox_params *mbcp) */ ql_write32(qdev, INTR_MASK, (INTR_MASK_PI << 16)); queue_delayed_work(qdev->workqueue, - &qdev->mpi_port_cfg_work, 0); + &qdev->mpi_port_cfg_work, 0); } ql_link_on(qdev); @@ -544,7 +544,6 @@ static int ql_mailbox_command(struct ql_adapter *qdev, struct mbox_params *mbcp) if (status) goto end; - /* If we're generating a system error, then there's nothing * to wait for. */ @@ -730,7 +729,6 @@ int ql_mb_set_port_cfg(struct ql_adapter *qdev) mbcp->mbox_in[1] = qdev->link_config; mbcp->mbox_in[2] = qdev->max_frame_size; - status = ql_mailbox_command(qdev, mbcp); if (status) return status; @@ -747,7 +745,7 @@ int ql_mb_set_port_cfg(struct ql_adapter *qdev) } static int ql_mb_dump_ram(struct ql_adapter *qdev, u64 req_dma, u32 addr, - u32 size) + u32 size) { int status = 0; struct mbox_params mbc; @@ -768,7 +766,6 @@ static int ql_mb_dump_ram(struct ql_adapter *qdev, u64 req_dma, u32 addr, mbcp->mbox_in[7] = LSW(MSD(req_dma)); mbcp->mbox_in[8] = MSW(addr); - status = ql_mailbox_command(qdev, mbcp); if (status) return status; @@ -782,14 +779,14 @@ static int ql_mb_dump_ram(struct ql_adapter *qdev, u64 req_dma, u32 addr, /* Issue a mailbox command to dump RISC RAM. */ int ql_dump_risc_ram_area(struct ql_adapter *qdev, void *buf, - u32 ram_addr, int word_count) + u32 ram_addr, int word_count) { int status; char *my_buf; dma_addr_t buf_dma; my_buf = pci_alloc_consistent(qdev->pdev, word_count * sizeof(u32), - &buf_dma); + &buf_dma); if (!my_buf) return -EIO; @@ -798,7 +795,7 @@ int ql_dump_risc_ram_area(struct ql_adapter *qdev, void *buf, memcpy(buf, my_buf, word_count * sizeof(u32)); pci_free_consistent(qdev->pdev, word_count * sizeof(u32), my_buf, - buf_dma); + buf_dma); return status; } @@ -850,7 +847,6 @@ int ql_mb_wol_mode(struct ql_adapter *qdev, u32 wol) mbcp->mbox_in[0] = MB_CMD_SET_WOL_MODE; mbcp->mbox_in[1] = wol; - status = ql_mailbox_command(qdev, mbcp); if (status) return status; @@ -922,7 +918,7 @@ static int ql_idc_wait(struct ql_adapter *qdev) */ wait_time = wait_for_completion_timeout(&qdev->ide_completion, - wait_time); + wait_time); if (!wait_time) { netif_err(qdev, drv, qdev->ndev, "IDC Timeout.\n"); break; @@ -965,7 +961,6 @@ int ql_mb_set_led_cfg(struct ql_adapter *qdev, u32 led_config) mbcp->mbox_in[0] = MB_CMD_SET_LED_CFG; mbcp->mbox_in[1] = led_config; - status = ql_mailbox_command(qdev, mbcp); if (status) return status; @@ -1130,8 +1125,7 @@ void ql_mpi_port_cfg_work(struct work_struct *work) } if (qdev->link_config & CFG_JUMBO_FRAME_SIZE && - qdev->max_frame_size == - CFG_DEFAULT_MAX_FRAME_SIZE) + qdev->max_frame_size == CFG_DEFAULT_MAX_FRAME_SIZE) goto end; qdev->link_config |= CFG_JUMBO_FRAME_SIZE; @@ -1278,7 +1272,7 @@ void ql_mpi_reset_work(struct work_struct *work) netif_err(qdev, drv, qdev->ndev, "Core is dumped!\n"); qdev->core_is_dumped = 1; queue_delayed_work(qdev->workqueue, - &qdev->mpi_core_to_log, 5 * HZ); + &qdev->mpi_core_to_log, 5 * HZ); } ql_soft_reset_mpi_risc(qdev); } diff --git a/drivers/staging/rtl8188eu/core/rtw_ap.c b/drivers/staging/rtl8188eu/core/rtw_ap.c index 88e42cc1d837..93283c7deec4 100644 --- a/drivers/staging/rtl8188eu/core/rtw_ap.c +++ b/drivers/staging/rtl8188eu/core/rtw_ap.c @@ -429,7 +429,7 @@ static void update_bmc_sta(struct adapter *padapter) /* prepare for add_RATid */ supportRateNum = rtw_get_rateset_len((u8 *)&pcur_network->SupportedRates); - network_type = rtw_check_network_type((u8 *)&pcur_network->SupportedRates, supportRateNum, 1); + network_type = rtw_check_network_type((u8 *)&pcur_network->SupportedRates); memcpy(psta->bssrateset, &pcur_network->SupportedRates, supportRateNum); psta->bssratelen = supportRateNum; @@ -802,7 +802,7 @@ int rtw_check_beacon_data(struct adapter *padapter, u8 *pbuf, int len) supportRateNum += ie_len; } - network_type = rtw_check_network_type(supportRate, supportRateNum, channel); + network_type = rtw_check_network_type(supportRate); rtw_set_supported_rate(pbss_network->SupportedRates, network_type); diff --git a/drivers/staging/rtl8188eu/core/rtw_efuse.c b/drivers/staging/rtl8188eu/core/rtw_efuse.c index d9b0f9e6235c..c525682d0edf 100644 --- a/drivers/staging/rtl8188eu/core/rtw_efuse.c +++ b/drivers/staging/rtl8188eu/core/rtw_efuse.c @@ -402,7 +402,6 @@ static u16 Efuse_GetCurrentSize(struct adapter *pAdapter) int Efuse_PgPacketRead(struct adapter *pAdapter, u8 offset, u8 *data) { u8 ReadState = PG_STATE_HEADER; - int bContinual = true; int bDataEmpty = true; u8 efuse_data, word_cnts = 0; u16 efuse_addr = 0; @@ -422,7 +421,7 @@ int Efuse_PgPacketRead(struct adapter *pAdapter, u8 offset, u8 *data) /* <Roger_TODO> Efuse has been pre-programmed dummy 5Bytes at the end of Efuse by CP. */ /* Skip dummy parts to prevent unexpected data read from Efuse. */ /* By pass right now. 2009.02.19. */ - while (bContinual && AVAILABLE_EFUSE_ADDR(efuse_addr)) { + while (AVAILABLE_EFUSE_ADDR(efuse_addr)) { /* Header Read ------------- */ if (ReadState & PG_STATE_HEADER) { if (efuse_OneByteRead(pAdapter, efuse_addr, &efuse_data) && (efuse_data != 0xFF)) { @@ -464,7 +463,7 @@ int Efuse_PgPacketRead(struct adapter *pAdapter, u8 offset, u8 *data) ReadState = PG_STATE_HEADER; } } else { - bContinual = false; + break; } } else if (ReadState & PG_STATE_DATA) { /* Data section Read ------------- */ @@ -498,8 +497,8 @@ static bool hal_EfuseFixHeaderProcess(struct adapter *pAdapter, u8 efuseType, st if (!PgWriteSuccess) return false; - else - efuse_addr = Efuse_GetCurrentSize(pAdapter); + + efuse_addr = Efuse_GetCurrentSize(pAdapter); } else { efuse_addr = efuse_addr + (pFixPkt->word_cnts * 2) + 1; } @@ -714,10 +713,9 @@ static bool hal_EfusePartialWriteCheck(struct adapter *pAdapter, u8 efuseType, u if (ALL_WORDS_DISABLED(efuse_data)) { ret = false; break; - } else { - curPkt.offset = ((cur_header & 0xE0) >> 5) | ((efuse_data & 0xF0) >> 1); - curPkt.word_en = efuse_data & 0x0F; } + curPkt.offset = ((cur_header & 0xE0) >> 5) | ((efuse_data & 0xF0) >> 1); + curPkt.word_en = efuse_data & 0x0F; } else { cur_header = efuse_data; curPkt.offset = (cur_header >> 4) & 0x0F; diff --git a/drivers/staging/rtl8188eu/core/rtw_ieee80211.c b/drivers/staging/rtl8188eu/core/rtw_ieee80211.c index cc1b5438c04c..29f615443e8f 100644 --- a/drivers/staging/rtl8188eu/core/rtw_ieee80211.c +++ b/drivers/staging/rtl8188eu/core/rtw_ieee80211.c @@ -98,7 +98,7 @@ bool rtw_is_cckratesonly_included(u8 *rate) return true; } -int rtw_check_network_type(unsigned char *rate, int ratelen, int channel) +int rtw_check_network_type(unsigned char *rate) { /* could be pure B, pure G, or B/G */ if (rtw_is_cckratesonly_included(rate)) @@ -157,11 +157,10 @@ u8 *rtw_get_ie(u8 *pbuf, int index, uint *len, int limit) if (*p == index) { *len = *(p + 1); return p; - } else { - tmp = *(p + 1); - p += (tmp + 2); - i += (tmp + 2); } + tmp = *(p + 1); + p += (tmp + 2); + i += (tmp + 2); if (i >= limit) break; } @@ -295,10 +294,9 @@ unsigned char *rtw_get_wpa_ie(unsigned char *pie, uint *wpa_ie_len, int limit) goto check_next_ie; *wpa_ie_len = *(pbuf + 1); return pbuf; - } else { - *wpa_ie_len = 0; - return NULL; } + *wpa_ie_len = 0; + return NULL; check_next_ie: limit_new = limit - (pbuf - pie) - 2 - len; @@ -596,9 +594,8 @@ u8 *rtw_get_wps_ie(u8 *in_ie, uint in_len, u8 *wps_ie, uint *wps_ielen) cnt += in_ie[cnt + 1] + 2; break; - } else { - cnt += in_ie[cnt + 1] + 2; /* goto next */ } + cnt += in_ie[cnt + 1] + 2; /* goto next */ } return wpsie_ptr; } @@ -642,9 +639,8 @@ u8 *rtw_get_wps_attr(u8 *wps_ie, uint wps_ielen, u16 target_attr_id, u8 *buf_att if (len_attr) *len_attr = attr_len; break; - } else { - attr_ptr += attr_len; /* goto next */ } + attr_ptr += attr_len; /* goto next */ } return target_attr_ptr; } diff --git a/drivers/staging/rtl8188eu/core/rtw_mlme_ext.c b/drivers/staging/rtl8188eu/core/rtw_mlme_ext.c index e984b4605e91..36841d20c3c1 100644 --- a/drivers/staging/rtl8188eu/core/rtw_mlme_ext.c +++ b/drivers/staging/rtl8188eu/core/rtw_mlme_ext.c @@ -291,7 +291,7 @@ static int update_hidden_ssid(u8 *ies, u32 ies_len, u8 hidden_ssid_mode) remain_len = ies_len - (next_ie - ies); ssid_ie[1] = 0; - memcpy(ssid_ie+2, next_ie, remain_len); + memcpy(ssid_ie + 2, next_ie, remain_len); len_diff -= ssid_len_ori; break; @@ -363,14 +363,14 @@ static void issue_beacon(struct adapter *padapter, int timeout_ms) memcpy(pframe, cur_network->ies, cur_network->ie_length); len_diff = update_hidden_ssid( - pframe+_BEACON_IE_OFFSET_ - , cur_network->ie_length-_BEACON_IE_OFFSET_ + pframe + _BEACON_IE_OFFSET_ + , cur_network->ie_length - _BEACON_IE_OFFSET_ , pmlmeinfo->hidden_ssid_mode ); - pframe += (cur_network->ie_length+len_diff); - pattrib->pktlen += (cur_network->ie_length+len_diff); - wps_ie = rtw_get_wps_ie(pmgntframe->buf_addr+TXDESC_OFFSET+sizeof(struct ieee80211_hdr_3addr)+_BEACON_IE_OFFSET_, - pattrib->pktlen-sizeof(struct ieee80211_hdr_3addr)-_BEACON_IE_OFFSET_, NULL, &wps_ielen); + pframe += (cur_network->ie_length + len_diff); + pattrib->pktlen += (cur_network->ie_length + len_diff); + wps_ie = rtw_get_wps_ie(pmgntframe->buf_addr + TXDESC_OFFSET + sizeof(struct ieee80211_hdr_3addr) + _BEACON_IE_OFFSET_, + pattrib->pktlen - sizeof(struct ieee80211_hdr_3addr) - _BEACON_IE_OFFSET_, NULL, &wps_ielen); if (wps_ie && wps_ielen > 0) rtw_get_wps_attr_content(wps_ie, wps_ielen, WPS_ATTR_SELECTED_REGISTRAR, (u8 *)(&sr), NULL); if (sr != 0) @@ -504,7 +504,7 @@ static void issue_probersp(struct adapter *padapter, unsigned char *da) #if defined(CONFIG_88EU_AP_MODE) if ((pmlmeinfo->state & 0x03) == WIFI_FW_AP_STATE) { - pwps_ie = rtw_get_wps_ie(cur_network->ies+_FIXED_IE_LENGTH_, cur_network->ie_length-_FIXED_IE_LENGTH_, NULL, &wps_ielen); + pwps_ie = rtw_get_wps_ie(cur_network->ies + _FIXED_IE_LENGTH_, cur_network->ie_length - _FIXED_IE_LENGTH_, NULL, &wps_ielen); /* inerset & update wps_probe_resp_ie */ if (pmlmepriv->wps_probe_resp_ie && pwps_ie && wps_ielen > 0) { @@ -522,13 +522,13 @@ static void issue_probersp(struct adapter *padapter, unsigned char *da) pattrib->pktlen += wps_offset; wps_ielen = (uint)pmlmepriv->wps_probe_resp_ie[1];/* to get ie data len */ - if ((wps_offset+wps_ielen+2) <= MAX_IE_SZ) { - memcpy(pframe, pmlmepriv->wps_probe_resp_ie, wps_ielen+2); - pframe += wps_ielen+2; - pattrib->pktlen += wps_ielen+2; + if ((wps_offset + wps_ielen + 2) <= MAX_IE_SZ) { + memcpy(pframe, pmlmepriv->wps_probe_resp_ie, wps_ielen + 2); + pframe += wps_ielen + 2; + pattrib->pktlen += wps_ielen + 2; } - if ((wps_offset+wps_ielen+2+remainder_ielen) <= MAX_IE_SZ) { + if ((wps_offset + wps_ielen + 2 + remainder_ielen) <= MAX_IE_SZ) { memcpy(pframe, premainder_ie, remainder_ielen); pframe += remainder_ielen; pattrib->pktlen += remainder_ielen; @@ -751,7 +751,7 @@ static void issue_auth(struct adapter *padapter, struct sta_info *psta, struct wlan_bssid_ex *pnetwork = &pmlmeinfo->network; pmgntframe = alloc_mgtxmitframe(pxmitpriv); - if (pmgntframe == NULL) + if (!pmgntframe) return; /* update attribute */ @@ -943,7 +943,7 @@ static void issue_asocrsp(struct adapter *padapter, unsigned short status, pframe = rtw_set_ie(pframe, _SUPPORTEDRATES_IE_, pstat->bssratelen, pstat->bssrateset, &pattrib->pktlen); } else { pframe = rtw_set_ie(pframe, _SUPPORTEDRATES_IE_, 8, pstat->bssrateset, &pattrib->pktlen); - pframe = rtw_set_ie(pframe, _EXT_SUPPORTEDRATES_IE_, pstat->bssratelen-8, pstat->bssrateset+8, &pattrib->pktlen); + pframe = rtw_set_ie(pframe, _EXT_SUPPORTEDRATES_IE_, pstat->bssratelen - 8, pstat->bssrateset + 8, &pattrib->pktlen); } if ((pstat->flags & WLAN_STA_HT) && (pmlmepriv->htpriv.ht_option)) { @@ -952,17 +952,17 @@ static void issue_asocrsp(struct adapter *padapter, unsigned short status, /* FILL HT CAP INFO IE */ pbuf = rtw_get_ie(ie + _BEACON_IE_OFFSET_, _HT_CAPABILITY_IE_, &ie_len, (pnetwork->ie_length - _BEACON_IE_OFFSET_)); if (pbuf && ie_len > 0) { - memcpy(pframe, pbuf, ie_len+2); - pframe += (ie_len+2); - pattrib->pktlen += (ie_len+2); + memcpy(pframe, pbuf, ie_len + 2); + pframe += (ie_len + 2); + pattrib->pktlen += (ie_len + 2); } /* FILL HT ADD INFO IE */ pbuf = rtw_get_ie(ie + _BEACON_IE_OFFSET_, _HT_ADD_INFO_IE_, &ie_len, (pnetwork->ie_length - _BEACON_IE_OFFSET_)); if (pbuf && ie_len > 0) { - memcpy(pframe, pbuf, ie_len+2); - pframe += (ie_len+2); - pattrib->pktlen += (ie_len+2); + memcpy(pframe, pbuf, ie_len + 2); + pframe += (ie_len + 2); + pattrib->pktlen += (ie_len + 2); } } @@ -973,14 +973,14 @@ static void issue_asocrsp(struct adapter *padapter, unsigned short status, for (pbuf = ie + _BEACON_IE_OFFSET_;; pbuf += (ie_len + 2)) { pbuf = rtw_get_ie(pbuf, _VENDOR_SPECIFIC_IE_, &ie_len, (pnetwork->ie_length - _BEACON_IE_OFFSET_ - (ie_len + 2))); - if (pbuf && !memcmp(pbuf+2, WMM_PARA_IE, 6)) { - memcpy(pframe, pbuf, ie_len+2); - pframe += (ie_len+2); - pattrib->pktlen += (ie_len+2); + if (pbuf && !memcmp(pbuf + 2, WMM_PARA_IE, 6)) { + memcpy(pframe, pbuf, ie_len + 2); + pframe += (ie_len + 2); + pattrib->pktlen += (ie_len + 2); break; } - if ((pbuf == NULL) || (ie_len == 0)) + if (!pbuf || ie_len == 0) break; } } @@ -1082,8 +1082,8 @@ static void issue_assocreq(struct adapter *padapter) /* Check if the AP's supported rates are also supported by STA. */ for (j = 0; j < sta_bssrate_len; j++) { /* Avoid the proprietary data rate (22Mbps) of Handlink WSG-4000 AP */ - if ((pmlmeinfo->network.SupportedRates[i]|IEEE80211_BASIC_RATE_MASK) - == (sta_bssrate[j]|IEEE80211_BASIC_RATE_MASK)) + if ((pmlmeinfo->network.SupportedRates[i] | IEEE80211_BASIC_RATE_MASK) + == (sta_bssrate[j] | IEEE80211_BASIC_RATE_MASK)) break; } @@ -1120,7 +1120,7 @@ static void issue_assocreq(struct adapter *padapter) /* HT caps */ if (padapter->mlmepriv.htpriv.ht_option) { p = rtw_get_ie((pmlmeinfo->network.ies + sizeof(struct ndis_802_11_fixed_ie)), _HT_CAPABILITY_IE_, &ie_len, (pmlmeinfo->network.ie_length - sizeof(struct ndis_802_11_fixed_ie))); - if ((p != NULL) && (!(is_ap_in_tkip(padapter)))) { + if (p && !is_ap_in_tkip(padapter)) { memcpy(&pmlmeinfo->HT_caps, p + 2, sizeof(struct ieee80211_ht_cap)); /* to disable 40M Hz support while gd_bw_40MHz_en = 0 */ @@ -1263,7 +1263,7 @@ int issue_nulldata(struct adapter *padapter, unsigned char *da, struct wlan_bssid_ex *pnetwork = &pmlmeinfo->network; /* da == NULL, assume it's null data for sta to ap*/ - if (da == NULL) + if (!da) da = pnetwork->MacAddress; do { @@ -1392,7 +1392,7 @@ int issue_qos_nulldata(struct adapter *padapter, unsigned char *da, struct wlan_bssid_ex *pnetwork = &pmlmeinfo->network; /* da == NULL, assume it's null data for sta to ap*/ - if (da == NULL) + if (!da) da = pnetwork->MacAddress; do { @@ -1444,7 +1444,7 @@ static int _issue_deauth(struct adapter *padapter, unsigned char *da, __le16 le_tmp; pmgntframe = alloc_mgtxmitframe(pxmitpriv); - if (pmgntframe == NULL) + if (!pmgntframe) goto exit; /* update attribute */ @@ -1780,7 +1780,7 @@ static void issue_action_BSSCoexistPacket(struct adapter *padapter) pbss_network = (struct wlan_bssid_ex *)&pnetwork->network; p = rtw_get_ie(pbss_network->ies + _FIXED_IE_LENGTH_, _HT_CAPABILITY_IE_, &len, pbss_network->ie_length - _FIXED_IE_LENGTH_); - if ((p == NULL) || (len == 0)) { /* non-HT */ + if (!p || len == 0) { /* non-HT */ if ((pbss_network->Configuration.DSConfig <= 0) || (pbss_network->Configuration.DSConfig > 14)) continue; @@ -1833,7 +1833,7 @@ unsigned int send_delba(struct adapter *padapter, u8 initiator, u8 *addr) return _SUCCESS; psta = rtw_get_stainfo(pstapriv, addr); - if (psta == NULL) + if (!psta) return _SUCCESS; if (initiator == 0) { /* recipient */ @@ -1865,6 +1865,7 @@ unsigned int send_beacon(struct adapter *padapter) int issue = 0; int poll = 0; unsigned long start = jiffies; + u32 passing_time; rtw_hal_set_hwreg(padapter, HW_VAR_BCN_VALID, NULL); do { @@ -1874,7 +1875,7 @@ unsigned int send_beacon(struct adapter *padapter) yield(); rtw_hal_get_hwreg(padapter, HW_VAR_BCN_VALID, (u8 *)(&bxmitok)); poll++; - } while ((poll%10) != 0 && !bxmitok && !padapter->bSurpriseRemoved && !padapter->bDriverStopped); + } while ((poll % 10) != 0 && !bxmitok && !padapter->bSurpriseRemoved && !padapter->bDriverStopped); } while (!bxmitok && issue < 100 && !padapter->bSurpriseRemoved && !padapter->bDriverStopped); if (padapter->bSurpriseRemoved || padapter->bDriverStopped) @@ -1883,15 +1884,14 @@ unsigned int send_beacon(struct adapter *padapter) DBG_88E("%s fail! %u ms\n", __func__, jiffies_to_msecs(jiffies - start)); return _FAIL; - } else { - u32 passing_time = jiffies_to_msecs(jiffies - start); - - if (passing_time > 100 || issue > 3) - DBG_88E("%s success, issue:%d, poll:%d, %u ms\n", - __func__, issue, poll, - jiffies_to_msecs(jiffies - start)); - return _SUCCESS; } + passing_time = jiffies_to_msecs(jiffies - start); + + if (passing_time > 100 || issue > 3) + DBG_88E("%s success, issue:%d, poll:%d, %u ms\n", + __func__, issue, poll, + jiffies_to_msecs(jiffies - start)); + return _SUCCESS; } /**************************************************************************** @@ -2082,7 +2082,7 @@ static u8 collect_bss_info(struct adapter *padapter, /* checking rate info... */ i = 0; p = rtw_get_ie(bssid->ies + ie_offset, _SUPPORTEDRATES_IE_, &len, bssid->ie_length - ie_offset); - if (p != NULL) { + if (p) { if (len > NDIS_802_11_LENGTH_RATES_EX) { DBG_88E("%s()-%d: IE too long (%d) for survey event\n", __func__, __LINE__, len); return _FAIL; @@ -2093,7 +2093,7 @@ static u8 collect_bss_info(struct adapter *padapter, p = rtw_get_ie(bssid->ies + ie_offset, _EXT_SUPPORTEDRATES_IE_, &len, bssid->ie_length - ie_offset); if (p) { - if (len > (NDIS_802_11_LENGTH_RATES_EX-i)) { + if (len > (NDIS_802_11_LENGTH_RATES_EX - i)) { DBG_88E("%s()-%d: IE too long (%d) for survey event\n", __func__, __LINE__, len); return _FAIL; } @@ -2518,7 +2518,7 @@ static unsigned int OnProbeReq(struct adapter *padapter, return _SUCCESS; if (!check_fwstate(pmlmepriv, _FW_LINKED) && - !check_fwstate(pmlmepriv, WIFI_ADHOC_MASTER_STATE|WIFI_AP_STATE)) + !check_fwstate(pmlmepriv, WIFI_ADHOC_MASTER_STATE | WIFI_AP_STATE)) return _SUCCESS; p = rtw_get_ie(pframe + WLAN_HDR_A3_LEN + _PROBEREQ_IE_OFFSET_, _SSID_IE_, &ielen, @@ -2526,7 +2526,7 @@ static unsigned int OnProbeReq(struct adapter *padapter, /* check (wildcard) SSID */ if (p) { - if ((ielen != 0 && memcmp((void *)(p+2), (void *)cur->ssid.ssid, cur->ssid.ssid_length)) || + if ((ielen != 0 && memcmp((void *)(p + 2), (void *)cur->ssid.ssid, cur->ssid.ssid_length)) || (ielen == 0 && pmlmeinfo->hidden_ssid_mode)) return _SUCCESS; @@ -2583,7 +2583,7 @@ static unsigned int OnBeacon(struct adapter *padapter, } /* check the vendor of the assoc AP */ - pmlmeinfo->assoc_AP_vendor = check_assoc_AP(pframe+sizeof(struct ieee80211_hdr_3addr), len-sizeof(struct ieee80211_hdr_3addr)); + pmlmeinfo->assoc_AP_vendor = check_assoc_AP(pframe + sizeof(struct ieee80211_hdr_3addr), len - sizeof(struct ieee80211_hdr_3addr)); /* update TSF Value */ update_TSF(pmlmeext, pframe, len); @@ -2596,7 +2596,7 @@ static unsigned int OnBeacon(struct adapter *padapter, if (((pmlmeinfo->state & 0x03) == WIFI_FW_STATION_STATE) && (pmlmeinfo->state & WIFI_FW_ASSOC_SUCCESS)) { psta = rtw_get_stainfo(pstapriv, GetAddr2Ptr(pframe)); - if (psta != NULL) { + if (psta) { ret = rtw_check_bcn_info(padapter, pframe, len); if (!ret) { DBG_88E_LEVEL(_drv_info_, "ap has changed, disconnect now\n "); @@ -2610,7 +2610,7 @@ static unsigned int OnBeacon(struct adapter *padapter, } } else if ((pmlmeinfo->state & 0x03) == WIFI_FW_ADHOC_STATE) { psta = rtw_get_stainfo(pstapriv, GetAddr2Ptr(pframe)); - if (psta != NULL) { + if (psta) { /* update WMM, ERP in the beacon */ /* todo: the timer is used instead of the number of the beacon received */ if ((sta_rx_pkts(psta) & 0xf) == 0) @@ -2729,7 +2729,7 @@ static unsigned int OnAuth(struct adapter *padapter, if ((pstat->auth_seq + 1) != seq) { DBG_88E("(1)auth rejected because out of seq [rx_seq=%d, exp_seq=%d]!\n", - seq, pstat->auth_seq+1); + seq, pstat->auth_seq + 1); status = _STATS_OUT_OF_AUTH_SEQ_; goto auth_fail; } @@ -2742,7 +2742,7 @@ static unsigned int OnAuth(struct adapter *padapter, pstat->authalg = algorithm; } else { DBG_88E("(2)auth rejected because out of seq [rx_seq=%d, exp_seq=%d]!\n", - seq, pstat->auth_seq+1); + seq, pstat->auth_seq + 1); status = _STATS_OUT_OF_AUTH_SEQ_; goto auth_fail; } @@ -2761,7 +2761,7 @@ static unsigned int OnAuth(struct adapter *padapter, p = rtw_get_ie(pframe + WLAN_HDR_A3_LEN + 4 + _AUTH_IE_OFFSET_, _CHLGETXT_IE_, &ie_len, len - WLAN_HDR_A3_LEN - _AUTH_IE_OFFSET_ - 4); - if ((p == NULL) || (ie_len <= 0)) { + if (!p || ie_len <= 0) { DBG_88E("auth rejected because challenge failure!(1)\n"); status = _STATS_CHALLENGE_FAIL_; goto auth_fail; @@ -2779,7 +2779,7 @@ static unsigned int OnAuth(struct adapter *padapter, } } else { DBG_88E("(3)auth rejected because out of seq [rx_seq=%d, exp_seq=%d]!\n", - seq, pstat->auth_seq+1); + seq, pstat->auth_seq + 1); status = _STATS_OUT_OF_AUTH_SEQ_; goto auth_fail; } @@ -2855,7 +2855,7 @@ static unsigned int OnAuthClient(struct adapter *padapter, p = rtw_get_ie(pframe + WLAN_HDR_A3_LEN + _AUTH_IE_OFFSET_, _CHLGETXT_IE_, &len, pkt_len - WLAN_HDR_A3_LEN - _AUTH_IE_OFFSET_); - if (p == NULL) + if (!p) goto authclnt_fail; memcpy((void *)(pmlmeinfo->chg_txt), (void *)(p + 2), len); @@ -2864,10 +2864,9 @@ static unsigned int OnAuthClient(struct adapter *padapter, set_link_timer(pmlmeext, REAUTH_TO); return _SUCCESS; - } else { - /* open system */ - go2asoc = 1; } + /* open system */ + go2asoc = 1; } else if (seq == 4) { if (pmlmeinfo->auth_algo == dot11AuthAlgrthm_Shared) go2asoc = 1; @@ -2975,7 +2974,7 @@ static unsigned int OnAssocReq(struct adapter *padapter, goto OnAssocReqFail; } else { /* check if ssid match */ - if (memcmp((void *)(p+2), cur->ssid.ssid, cur->ssid.ssid_length)) + if (memcmp((void *)(p + 2), cur->ssid.ssid, cur->ssid.ssid_length)) status = _STATS_FAILURE_; if (ie_len != cur->ssid.ssid_length) @@ -2987,7 +2986,7 @@ static unsigned int OnAssocReq(struct adapter *padapter, /* check if the supported rate is ok */ p = rtw_get_ie(pframe + WLAN_HDR_A3_LEN + ie_offset, _SUPPORTEDRATES_IE_, &ie_len, pkt_len - WLAN_HDR_A3_LEN - ie_offset); - if (p == NULL) { + if (!p) { DBG_88E("Rx a sta assoc-req which supported rate is empty!\n"); /* use our own rate set as statoin used */ /* memcpy(supportRate, AP_BSSRATE, AP_BSSRATE_LEN); */ @@ -2996,14 +2995,15 @@ static unsigned int OnAssocReq(struct adapter *padapter, status = _STATS_FAILURE_; goto OnAssocReqFail; } else { - memcpy(supportRate, p+2, ie_len); + memcpy(supportRate, p + 2, ie_len); supportRateNum = ie_len; p = rtw_get_ie(pframe + WLAN_HDR_A3_LEN + ie_offset, _EXT_SUPPORTEDRATES_IE_, &ie_len, pkt_len - WLAN_HDR_A3_LEN - ie_offset); - if (p != NULL) { + if (p) { if (supportRateNum <= sizeof(supportRate)) { - memcpy(supportRate+supportRateNum, p+2, ie_len); + memcpy(supportRate + supportRateNum, + p + 2, ie_len); supportRateNum += ie_len; } } @@ -3031,7 +3031,7 @@ static unsigned int OnAssocReq(struct adapter *padapter, wpa_ie = elems.rsn_ie; wpa_ie_len = elems.rsn_ie_len; - if (rtw_parse_wpa2_ie(wpa_ie-2, wpa_ie_len+2, &group_cipher, &pairwise_cipher, NULL) == _SUCCESS) { + if (rtw_parse_wpa2_ie(wpa_ie - 2, wpa_ie_len + 2, &group_cipher, &pairwise_cipher, NULL) == _SUCCESS) { pstat->dot8021xalg = 1;/* psk, todo:802.1x */ pstat->wpa_psk |= BIT(1); @@ -3052,7 +3052,7 @@ static unsigned int OnAssocReq(struct adapter *padapter, wpa_ie = elems.wpa_ie; wpa_ie_len = elems.wpa_ie_len; - if (rtw_parse_wpa_ie(wpa_ie-2, wpa_ie_len+2, &group_cipher, &pairwise_cipher, NULL) == _SUCCESS) { + if (rtw_parse_wpa_ie(wpa_ie - 2, wpa_ie_len + 2, &group_cipher, &pairwise_cipher, NULL) == _SUCCESS) { pstat->dot8021xalg = 1;/* psk, todo:802.1x */ pstat->wpa_psk |= BIT(0); @@ -3094,7 +3094,7 @@ static unsigned int OnAssocReq(struct adapter *padapter, /* AP support WPA/RSN, and sta is going to do WPS, but AP is not ready */ /* that the selected registrar of AP is _FLASE */ - if ((psecuritypriv->wpa_psk > 0) && (pstat->flags & (WLAN_STA_WPS|WLAN_STA_MAYBE_WPS))) { + if ((psecuritypriv->wpa_psk > 0) && (pstat->flags & (WLAN_STA_WPS | WLAN_STA_MAYBE_WPS))) { if (pmlmepriv->wps_beacon_ie) { u8 selected_registrar = 0; @@ -3131,7 +3131,7 @@ static unsigned int OnAssocReq(struct adapter *padapter, copy_len = min_t(int, wpa_ie_len + 2, sizeof(pstat->wpa_ie)); } if (copy_len > 0) - memcpy(pstat->wpa_ie, wpa_ie-2, copy_len); + memcpy(pstat->wpa_ie, wpa_ie - 2, copy_len); } /* check if there is WMM IE & support WWM-PS */ pstat->flags &= ~WLAN_STA_WME; @@ -3146,14 +3146,14 @@ static unsigned int OnAssocReq(struct adapter *padapter, p = pframe + WLAN_HDR_A3_LEN + ie_offset; ie_len = 0; for (;;) { p = rtw_get_ie(p, _VENDOR_SPECIFIC_IE_, &ie_len, pkt_len - WLAN_HDR_A3_LEN - ie_offset); - if (p != NULL) { - if (!memcmp(p+2, WMM_IE, 6)) { + if (p) { + if (!memcmp(p + 2, WMM_IE, 6)) { pstat->flags |= WLAN_STA_WME; pstat->qos_option = 1; - pstat->qos_info = *(p+8); + pstat->qos_info = *(p + 8); - pstat->max_sp_len = (pstat->qos_info>>5) & 0x3; + pstat->max_sp_len = (pstat->qos_info >> 5) & 0x3; if ((pstat->qos_info & 0xf) != 0xf) pstat->has_legacy_ac = true; @@ -3162,22 +3162,22 @@ static unsigned int OnAssocReq(struct adapter *padapter, if (pstat->qos_info & 0xf) { if (pstat->qos_info & BIT(0)) - pstat->uapsd_vo = BIT(0)|BIT(1); + pstat->uapsd_vo = BIT(0) | BIT(1); else pstat->uapsd_vo = 0; if (pstat->qos_info & BIT(1)) - pstat->uapsd_vi = BIT(0)|BIT(1); + pstat->uapsd_vi = BIT(0) | BIT(1); else pstat->uapsd_vi = 0; if (pstat->qos_info & BIT(2)) - pstat->uapsd_bk = BIT(0)|BIT(1); + pstat->uapsd_bk = BIT(0) | BIT(1); else pstat->uapsd_bk = 0; if (pstat->qos_info & BIT(3)) - pstat->uapsd_be = BIT(0)|BIT(1); + pstat->uapsd_be = BIT(0) | BIT(1); else pstat->uapsd_be = 0; } @@ -3245,7 +3245,7 @@ static unsigned int OnAssocReq(struct adapter *padapter, DBG_88E(" old AID %d\n", pstat->aid); } else { for (pstat->aid = 1; pstat->aid <= NUM_STA; pstat->aid++) - if (pstapriv->sta_aid[pstat->aid - 1] == NULL) + if (!pstapriv->sta_aid[pstat->aid - 1]) break; /* if (pstat->aid > NUM_STA) { */ @@ -3452,14 +3452,13 @@ static unsigned int OnDeAuth(struct adapter *padapter, } return _SUCCESS; - } else + } #endif - { - DBG_88E_LEVEL(_drv_always_, "sta recv deauth reason code(%d) sta:%pM\n", - reason, GetAddr3Ptr(pframe)); + DBG_88E_LEVEL(_drv_always_, "sta recv deauth reason code(%d) sta:%pM\n", + reason, GetAddr3Ptr(pframe)); + + receive_disconnect(padapter, GetAddr3Ptr(pframe), reason); - receive_disconnect(padapter, GetAddr3Ptr(pframe), reason); - } pmlmepriv->LinkDetectInfo.bBusyTraffic = false; return _SUCCESS; } @@ -3506,14 +3505,13 @@ static unsigned int OnDisassoc(struct adapter *padapter, } return _SUCCESS; - } else + } #endif - { - DBG_88E_LEVEL(_drv_always_, "ap recv disassoc reason code(%d) sta:%pM\n", - reason, GetAddr3Ptr(pframe)); + DBG_88E_LEVEL(_drv_always_, "ap recv disassoc reason code(%d) sta:%pM\n", + reason, GetAddr3Ptr(pframe)); + + receive_disconnect(padapter, GetAddr3Ptr(pframe), reason); - receive_disconnect(padapter, GetAddr3Ptr(pframe), reason); - } pmlmepriv->LinkDetectInfo.bBusyTraffic = false; return _SUCCESS; } @@ -3958,7 +3956,7 @@ static void init_channel_list(struct adapter *padapter, ((o->bw == BW40MINUS) || (o->bw == BW40PLUS))) continue; - if (reg == NULL) { + if (!reg) { reg = &channel_list->reg_class[cla]; cla++; reg->reg_class = o->op_class; @@ -4515,7 +4513,7 @@ void mlmeext_joinbss_event_callback(struct adapter *padapter, int join_res) /* set per sta rate after updating HT cap. */ set_sta_rate(padapter, psta); rtw_hal_set_hwreg(padapter, HW_VAR_TX_RPT_MAX_MACID, (u8 *)&psta->mac_id); - media_status = (psta->mac_id<<8)|1; /* MACID|OPMODE: 1 means connect */ + media_status = (psta->mac_id << 8) | 1; /* MACID|OPMODE: 1 means connect */ rtw_hal_set_hwreg(padapter, HW_VAR_H2C_MEDIA_STATUS_RPT, (u8 *)&media_status); } @@ -4844,7 +4842,7 @@ u8 setopmode_hdl(struct adapter *padapter, u8 *pbuf) pmlmeinfo->state = WIFI_FW_AP_STATE; type = _HW_STATE_AP_; } else if (psetop->mode == Ndis802_11Infrastructure) { - pmlmeinfo->state &= ~(BIT(0)|BIT(1));/* clear state */ + pmlmeinfo->state &= ~(BIT(0) | BIT(1));/* clear state */ pmlmeinfo->state |= WIFI_FW_STATION_STATE;/* set to STATION_STATE */ type = _HW_STATE_STATION_; } else if (psetop->mode == Ndis802_11IBSS) { @@ -5040,7 +5038,7 @@ u8 disconnect_hdl(struct adapter *padapter, unsigned char *pbuf) u8 val8; if (is_client_associated_to_ap(padapter)) - issue_deauth_ex(padapter, pnetwork->MacAddress, WLAN_REASON_DEAUTH_LEAVING, param->deauth_timeout_ms/100, 100); + issue_deauth_ex(padapter, pnetwork->MacAddress, WLAN_REASON_DEAUTH_LEAVING, param->deauth_timeout_ms / 100, 100); rtw_hal_set_hwreg(padapter, HW_VAR_MLME_DISCONNECT, NULL); rtw_hal_set_hwreg(padapter, HW_VAR_BSSID, null_addr); @@ -5084,7 +5082,7 @@ static int rtw_scan_ch_decision(struct adapter *padapter, struct mlme_ext_priv *pmlmeext = &padapter->mlmeextpriv; /* clear out first */ - memset(out, 0, sizeof(struct rtw_ieee80211_channel)*out_num); + memset(out, 0, sizeof(struct rtw_ieee80211_channel) * out_num); /* acquire channels from in */ j = 0; @@ -5263,7 +5261,7 @@ u8 set_stakey_hdl(struct adapter *padapter, u8 *pbuf) DBG_88E("r871x_set_stakey_hdl(): enc_algorithm=%d\n", pparm->algorithm); - if ((psta->mac_id < 1) || (psta->mac_id > (NUM_STA-4))) { + if ((psta->mac_id < 1) || (psta->mac_id > (NUM_STA - 4))) { DBG_88E("r871x_set_stakey_hdl():set_stakey failed, mac_id(aid)=%d\n", psta->mac_id); return H2C_REJECTED; } @@ -5276,10 +5274,10 @@ u8 set_stakey_hdl(struct adapter *padapter, u8 *pbuf) write_cam(padapter, cam_id, ctrl, pparm->addr, pparm->key); return H2C_SUCCESS_RSP; - } else { - DBG_88E("r871x_set_stakey_hdl(): sta has been free\n"); - return H2C_REJECTED; } + + DBG_88E("r871x_set_stakey_hdl(): sta has been free\n"); + return H2C_REJECTED; } /* below for sta mode */ @@ -5333,14 +5331,14 @@ u8 set_tx_beacon_cmd(struct adapter *padapter) ptxBeacon_parm = kmemdup(&pmlmeinfo->network, sizeof(struct wlan_bssid_ex), GFP_ATOMIC); - if (ptxBeacon_parm == NULL) { + if (!ptxBeacon_parm) { kfree(ph2c); res = _FAIL; goto exit; } - len_diff = update_hidden_ssid(ptxBeacon_parm->ies+_BEACON_IE_OFFSET_, - ptxBeacon_parm->ie_length-_BEACON_IE_OFFSET_, + len_diff = update_hidden_ssid(ptxBeacon_parm->ies + _BEACON_IE_OFFSET_, + ptxBeacon_parm->ie_length - _BEACON_IE_OFFSET_, pmlmeinfo->hidden_ssid_mode); ptxBeacon_parm->ie_length += len_diff; @@ -5361,7 +5359,7 @@ u8 mlme_evt_hdl(struct adapter *padapter, unsigned char *pbuf) peventbuf = (uint *)pbuf; evt_sz = (u16)(*peventbuf & 0xffff); - evt_code = (u8)((*peventbuf>>16) & 0xff); + evt_code = (u8)((*peventbuf >> 16) & 0xff); /* checking if event code is valid */ if (evt_code >= MAX_C2HEVT) { diff --git a/drivers/staging/rtl8188eu/core/rtw_pwrctrl.c b/drivers/staging/rtl8188eu/core/rtw_pwrctrl.c index 03dc7e5fcc38..c4f58507dbfd 100644 --- a/drivers/staging/rtl8188eu/core/rtw_pwrctrl.c +++ b/drivers/staging/rtl8188eu/core/rtw_pwrctrl.c @@ -154,8 +154,8 @@ void ips_enter(struct adapter *padapter) int ips_leave(struct adapter *padapter) { struct pwrctrl_priv *pwrpriv = &padapter->pwrctrlpriv; - struct security_priv *psecuritypriv = &(padapter->securitypriv); - struct mlme_priv *pmlmepriv = &(padapter->mlmepriv); + struct security_priv *psecuritypriv = &padapter->securitypriv; + struct mlme_priv *pmlmepriv = &padapter->mlmepriv; int result = _SUCCESS; int keyid; @@ -200,28 +200,24 @@ int ips_leave(struct adapter *padapter) static bool rtw_pwr_unassociated_idle(struct adapter *adapter) { - struct mlme_priv *pmlmepriv = &(adapter->mlmepriv); - bool ret = false; + struct mlme_priv *pmlmepriv = &adapter->mlmepriv; if (time_after_eq(adapter->pwrctrlpriv.ips_deny_time, jiffies)) - goto exit; + return false; if (check_fwstate(pmlmepriv, WIFI_ASOC_STATE|WIFI_SITE_MONITOR) || check_fwstate(pmlmepriv, WIFI_UNDER_LINKING|WIFI_UNDER_WPS) || check_fwstate(pmlmepriv, WIFI_AP_STATE) || check_fwstate(pmlmepriv, WIFI_ADHOC_MASTER_STATE|WIFI_ADHOC_STATE)) - goto exit; - - ret = true; + return false; -exit: - return ret; + return true; } void rtw_ps_processor(struct adapter *padapter) { struct pwrctrl_priv *pwrpriv = &padapter->pwrctrlpriv; - struct mlme_priv *pmlmepriv = &(padapter->mlmepriv); + struct mlme_priv *pmlmepriv = &padapter->mlmepriv; enum rt_rf_power_state rfpwrstate; pwrpriv->ps_processing = true; @@ -282,7 +278,7 @@ static void pwr_state_check_handler(struct timer_list *t) */ void rtw_set_rpwm(struct adapter *padapter, u8 pslv) { - u8 rpwm; + u8 rpwm; struct pwrctrl_priv *pwrpriv = &padapter->pwrctrlpriv; pslv = PS_STATE(pslv); @@ -335,8 +331,8 @@ void rtw_set_rpwm(struct adapter *padapter, u8 pslv) static u8 PS_RDY_CHECK(struct adapter *padapter) { unsigned long curr_time, delta_time; - struct pwrctrl_priv *pwrpriv = &padapter->pwrctrlpriv; - struct mlme_priv *pmlmepriv = &(padapter->mlmepriv); + struct pwrctrl_priv *pwrpriv = &padapter->pwrctrlpriv; + struct mlme_priv *pmlmepriv = &padapter->mlmepriv; curr_time = jiffies; delta_time = curr_time - pwrpriv->DelayLPSLastTimeStamp; @@ -437,7 +433,7 @@ s32 LPS_RF_ON_check(struct adapter *padapter, u32 delay_ms) /* */ void LPS_Enter(struct adapter *padapter) { - struct pwrctrl_priv *pwrpriv = &padapter->pwrctrlpriv; + struct pwrctrl_priv *pwrpriv = &padapter->pwrctrlpriv; if (!PS_RDY_CHECK(padapter)) return; @@ -463,7 +459,7 @@ void LPS_Enter(struct adapter *padapter) /* Leave the leisure power save mode. */ void LPS_Leave(struct adapter *padapter) { - struct pwrctrl_priv *pwrpriv = &padapter->pwrctrlpriv; + struct pwrctrl_priv *pwrpriv = &padapter->pwrctrlpriv; if (pwrpriv->bLeisurePs) { if (pwrpriv->pwr_mode != PS_MODE_ACTIVE) { @@ -483,8 +479,8 @@ void LPS_Leave(struct adapter *padapter) /* */ void LeaveAllPowerSaveMode(struct adapter *Adapter) { - struct mlme_priv *pmlmepriv = &(Adapter->mlmepriv); - u8 enqueue = 0; + struct mlme_priv *pmlmepriv = &Adapter->mlmepriv; + u8 enqueue = 0; if (check_fwstate(pmlmepriv, _FW_LINKED)) rtw_lps_ctrl_wk_cmd(Adapter, LPS_CTRL_LEAVE, enqueue); @@ -611,7 +607,7 @@ exit: int rtw_pm_set_lps(struct adapter *padapter, u8 mode) { - int ret = 0; + int ret = 0; struct pwrctrl_priv *pwrctrlpriv = &padapter->pwrctrlpriv; if (mode < PS_MODE_NUM) { diff --git a/drivers/staging/rtl8188eu/core/rtw_wlan_util.c b/drivers/staging/rtl8188eu/core/rtw_wlan_util.c index af8a79ce8736..6df873e4c2ed 100644 --- a/drivers/staging/rtl8188eu/core/rtw_wlan_util.c +++ b/drivers/staging/rtl8188eu/core/rtw_wlan_util.c @@ -1247,9 +1247,8 @@ unsigned char check_assoc_AP(u8 *pframe, uint len) if (ralink_vendor_flag) { DBG_88E("link to Tenda W311R AP\n"); return HT_IOT_PEER_TENDA; - } else { - DBG_88E("Capture EPIGRAM_OUI\n"); } + DBG_88E("Capture EPIGRAM_OUI\n"); } else { break; } @@ -1266,10 +1265,9 @@ unsigned char check_assoc_AP(u8 *pframe, uint len) } else if (ralink_vendor_flag && epigram_vendor_flag) { DBG_88E("link to Tenda W311R AP\n"); return HT_IOT_PEER_TENDA; - } else { - DBG_88E("link to new AP\n"); - return HT_IOT_PEER_UNKNOWN; } + DBG_88E("link to new AP\n"); + return HT_IOT_PEER_UNKNOWN; } void update_IOT_info(struct adapter *padapter) diff --git a/drivers/staging/rtl8188eu/core/rtw_xmit.c b/drivers/staging/rtl8188eu/core/rtw_xmit.c index c37591657bac..258531bc1408 100644 --- a/drivers/staging/rtl8188eu/core/rtw_xmit.c +++ b/drivers/staging/rtl8188eu/core/rtw_xmit.c @@ -1022,10 +1022,10 @@ s32 rtw_xmitframe_coalesce(struct adapter *padapter, struct sk_buff *pkt, struct ClearMFrag(mem_start); break; - } else { - RT_TRACE(_module_rtl871x_xmit_c_, _drv_err_, ("%s: There're still something in packet!\n", __func__)); } + RT_TRACE(_module_rtl871x_xmit_c_, _drv_err_, ("%s: There're still something in packet!\n", __func__)); + addr = (size_t)(pframe); mem_start = (unsigned char *)round_up(addr, 4) + hw_hdr_offset; diff --git a/drivers/staging/rtl8188eu/hal/odm.c b/drivers/staging/rtl8188eu/hal/odm.c index 4e2f6cb55a75..7489491f5aaa 100644 --- a/drivers/staging/rtl8188eu/hal/odm.c +++ b/drivers/staging/rtl8188eu/hal/odm.c @@ -967,10 +967,11 @@ void ODM_TXPowerTrackingCheck(struct odm_dm_struct *pDM_Odm) pDM_Odm->RFCalibrateInfo.TM_Trigger = 1; return; - } else { - rtl88eu_dm_txpower_tracking_callback_thermalmeter(Adapter); - pDM_Odm->RFCalibrateInfo.TM_Trigger = 0; } + + rtl88eu_dm_txpower_tracking_callback_thermalmeter(Adapter); + pDM_Odm->RFCalibrateInfo.TM_Trigger = 0; + } /* 3============================================================ */ diff --git a/drivers/staging/rtl8188eu/hal/odm_rtl8188e.c b/drivers/staging/rtl8188eu/hal/odm_rtl8188e.c index 251bd8aba3b1..a55a0d8b9fb7 100644 --- a/drivers/staging/rtl8188eu/hal/odm_rtl8188e.c +++ b/drivers/staging/rtl8188eu/hal/odm_rtl8188e.c @@ -154,35 +154,37 @@ void rtl88eu_dm_update_rx_idle_ant(struct odm_dm_struct *dm_odm, u8 ant) struct adapter *adapter = dm_odm->Adapter; u32 default_ant, optional_ant; - if (dm_fat_tbl->RxIdleAnt != ant) { - if (ant == MAIN_ANT) { - default_ant = (dm_odm->AntDivType == CG_TRX_HW_ANTDIV) ? - MAIN_ANT_CG_TRX : MAIN_ANT_CGCS_RX; - optional_ant = (dm_odm->AntDivType == CG_TRX_HW_ANTDIV) ? - AUX_ANT_CG_TRX : AUX_ANT_CGCS_RX; - } else { - default_ant = (dm_odm->AntDivType == CG_TRX_HW_ANTDIV) ? - AUX_ANT_CG_TRX : AUX_ANT_CGCS_RX; - optional_ant = (dm_odm->AntDivType == CG_TRX_HW_ANTDIV) ? - MAIN_ANT_CG_TRX : MAIN_ANT_CGCS_RX; - } + if (dm_fat_tbl->RxIdleAnt == ant) + return; - if (dm_odm->AntDivType == CG_TRX_HW_ANTDIV) { - phy_set_bb_reg(adapter, ODM_REG_RX_ANT_CTRL_11N, - BIT(5) | BIT(4) | BIT(3), default_ant); - phy_set_bb_reg(adapter, ODM_REG_RX_ANT_CTRL_11N, - BIT(8) | BIT(7) | BIT(6), optional_ant); - phy_set_bb_reg(adapter, ODM_REG_ANTSEL_CTRL_11N, - BIT(14) | BIT(13) | BIT(12), default_ant); - phy_set_bb_reg(adapter, ODM_REG_RESP_TX_11N, - BIT(6) | BIT(7), default_ant); - } else if (dm_odm->AntDivType == CGCS_RX_HW_ANTDIV) { - phy_set_bb_reg(adapter, ODM_REG_RX_ANT_CTRL_11N, - BIT(5) | BIT(4) | BIT(3), default_ant); - phy_set_bb_reg(adapter, ODM_REG_RX_ANT_CTRL_11N, - BIT(8) | BIT(7) | BIT(6), optional_ant); - } + if (ant == MAIN_ANT) { + default_ant = (dm_odm->AntDivType == CG_TRX_HW_ANTDIV) ? + MAIN_ANT_CG_TRX : MAIN_ANT_CGCS_RX; + optional_ant = (dm_odm->AntDivType == CG_TRX_HW_ANTDIV) ? + AUX_ANT_CG_TRX : AUX_ANT_CGCS_RX; + } else { + default_ant = (dm_odm->AntDivType == CG_TRX_HW_ANTDIV) ? + AUX_ANT_CG_TRX : AUX_ANT_CGCS_RX; + optional_ant = (dm_odm->AntDivType == CG_TRX_HW_ANTDIV) ? + MAIN_ANT_CG_TRX : MAIN_ANT_CGCS_RX; + } + + if (dm_odm->AntDivType == CG_TRX_HW_ANTDIV) { + phy_set_bb_reg(adapter, ODM_REG_RX_ANT_CTRL_11N, + BIT(5) | BIT(4) | BIT(3), default_ant); + phy_set_bb_reg(adapter, ODM_REG_RX_ANT_CTRL_11N, + BIT(8) | BIT(7) | BIT(6), optional_ant); + phy_set_bb_reg(adapter, ODM_REG_ANTSEL_CTRL_11N, + BIT(14) | BIT(13) | BIT(12), default_ant); + phy_set_bb_reg(adapter, ODM_REG_RESP_TX_11N, + BIT(6) | BIT(7), default_ant); + } else if (dm_odm->AntDivType == CGCS_RX_HW_ANTDIV) { + phy_set_bb_reg(adapter, ODM_REG_RX_ANT_CTRL_11N, + BIT(5) | BIT(4) | BIT(3), default_ant); + phy_set_bb_reg(adapter, ODM_REG_RX_ANT_CTRL_11N, + BIT(8) | BIT(7) | BIT(6), optional_ant); } + dm_fat_tbl->RxIdleAnt = ant; } @@ -303,6 +305,7 @@ void rtl88eu_dm_antenna_diversity(struct odm_dm_struct *dm_odm) if (!(dm_odm->SupportAbility & ODM_BB_ANT_DIV)) return; + if (!dm_odm->bLinked) { ODM_RT_TRACE(dm_odm, ODM_COMP_ANT_DIV, ODM_DBG_LOUD, ("ODM_AntennaDiversity_88E(): No Link.\n")); @@ -318,19 +321,20 @@ void rtl88eu_dm_antenna_diversity(struct odm_dm_struct *dm_odm) dm_fat_tbl->bBecomeLinked = dm_odm->bLinked; } return; - } else { - if (!dm_fat_tbl->bBecomeLinked) { - ODM_RT_TRACE(dm_odm, ODM_COMP_ANT_DIV, ODM_DBG_LOUD, - ("Need to Turn on HW AntDiv\n")); - phy_set_bb_reg(adapter, ODM_REG_IGI_A_11N, BIT(7), 1); - phy_set_bb_reg(adapter, ODM_REG_CCK_ANTDIV_PARA1_11N, - BIT(15), 1); - if (dm_odm->AntDivType == CG_TRX_HW_ANTDIV) - phy_set_bb_reg(adapter, ODM_REG_TX_ANT_CTRL_11N, - BIT(21), 1); - dm_fat_tbl->bBecomeLinked = dm_odm->bLinked; - } } + + if (!dm_fat_tbl->bBecomeLinked) { + ODM_RT_TRACE(dm_odm, ODM_COMP_ANT_DIV, ODM_DBG_LOUD, + ("Need to Turn on HW AntDiv\n")); + phy_set_bb_reg(adapter, ODM_REG_IGI_A_11N, BIT(7), 1); + phy_set_bb_reg(adapter, ODM_REG_CCK_ANTDIV_PARA1_11N, + BIT(15), 1); + if (dm_odm->AntDivType == CG_TRX_HW_ANTDIV) + phy_set_bb_reg(adapter, ODM_REG_TX_ANT_CTRL_11N, + BIT(21), 1); + dm_fat_tbl->bBecomeLinked = dm_odm->bLinked; + } + if ((dm_odm->AntDivType == CG_TRX_HW_ANTDIV) || (dm_odm->AntDivType == CGCS_RX_HW_ANTDIV)) rtl88eu_dm_hw_ant_div(dm_odm); diff --git a/drivers/staging/rtl8188eu/hal/phy.c b/drivers/staging/rtl8188eu/hal/phy.c index 51c40abfafaa..afaf9e55195a 100644 --- a/drivers/staging/rtl8188eu/hal/phy.c +++ b/drivers/staging/rtl8188eu/hal/phy.c @@ -923,27 +923,27 @@ static bool simularity_compare(struct adapter *adapt, s32 resulta[][8], } } return result; - } else { - if (!(sim_bitmap & 0x03)) { /* path A TX OK */ - for (i = 0; i < 2; i++) - resulta[3][i] = resulta[c1][i]; - } - if (!(sim_bitmap & 0x0c)) { /* path A RX OK */ - for (i = 2; i < 4; i++) - resulta[3][i] = resulta[c1][i]; - } + } - if (!(sim_bitmap & 0x30)) { /* path B TX OK */ - for (i = 4; i < 6; i++) - resulta[3][i] = resulta[c1][i]; - } + if (!(sim_bitmap & 0x03)) { /* path A TX OK */ + for (i = 0; i < 2; i++) + resulta[3][i] = resulta[c1][i]; + } + if (!(sim_bitmap & 0x0c)) { /* path A RX OK */ + for (i = 2; i < 4; i++) + resulta[3][i] = resulta[c1][i]; + } - if (!(sim_bitmap & 0xc0)) { /* path B RX OK */ - for (i = 6; i < 8; i++) - resulta[3][i] = resulta[c1][i]; - } - return false; + if (!(sim_bitmap & 0x30)) { /* path B TX OK */ + for (i = 4; i < 6; i++) + resulta[3][i] = resulta[c1][i]; + } + + if (!(sim_bitmap & 0xc0)) { /* path B RX OK */ + for (i = 6; i < 8; i++) + resulta[3][i] = resulta[c1][i]; } + return false; } static void phy_iq_calibrate(struct adapter *adapt, s32 result[][8], @@ -1053,10 +1053,9 @@ static void phy_iq_calibrate(struct adapter *adapt, s32 result[][8], result[t][3] = (phy_query_bb_reg(adapt, rRx_Power_After_IQK_A_2, bMaskDWord)&0x3FF0000)>>16; break; - } else { - ODM_RT_TRACE(dm_odm, ODM_COMP_CALIBRATION, ODM_DBG_LOUD, - ("Path A Rx IQK Fail!!\n")); } + ODM_RT_TRACE(dm_odm, ODM_COMP_CALIBRATION, ODM_DBG_LOUD, + ("Path A Rx IQK Fail!!\n")); } if (path_a_ok == 0x00) { diff --git a/drivers/staging/rtl8188eu/hal/rtl8188e_dm.c b/drivers/staging/rtl8188eu/hal/rtl8188e_dm.c index 545d6a6102f1..241f55b92808 100644 --- a/drivers/staging/rtl8188eu/hal/rtl8188e_dm.c +++ b/drivers/staging/rtl8188eu/hal/rtl8188e_dm.c @@ -21,7 +21,7 @@ /* Initialize GPIO setting registers */ static void dm_InitGPIOSetting(struct adapter *Adapter) { - u8 tmp1byte; + u8 tmp1byte; tmp1byte = usb_read8(Adapter, REG_GPIO_MUXCFG); tmp1byte &= (GPIOSEL_GPIO | ~GPIOSEL_ENBT); @@ -35,8 +35,8 @@ static void dm_InitGPIOSetting(struct adapter *Adapter) static void Init_ODM_ComInfo_88E(struct adapter *Adapter) { struct hal_data_8188e *hal_data = Adapter->HalData; - struct dm_priv *pdmpriv = &hal_data->dmpriv; - struct odm_dm_struct *dm_odm = &(hal_data->odmpriv); + struct dm_priv *pdmpriv = &hal_data->dmpriv; + struct odm_dm_struct *dm_odm = &hal_data->odmpriv; /* Init Value */ memset(dm_odm, 0, sizeof(*dm_odm)); @@ -51,44 +51,46 @@ static void Init_ODM_ComInfo_88E(struct adapter *Adapter) dm_odm->AntDivType = hal_data->TRxAntDivType; - /* Tx power tracking BB swing table. */ - /* The base index = 12. +((12-n)/2)dB 13~?? = decrease tx pwr by -((n-12)/2)dB */ + /* Tx power tracking BB swing table. + * The base index = + * 12. +((12-n)/2)dB 13~?? = decrease tx pwr by -((n-12)/2)dB + */ dm_odm->BbSwingIdxOfdm = 12; /* Set defalut value as index 12. */ dm_odm->BbSwingIdxOfdmCurrent = 12; dm_odm->BbSwingFlagOfdm = false; - pdmpriv->InitODMFlag = ODM_RF_CALIBRATION | - ODM_RF_TX_PWR_TRACK; + pdmpriv->InitODMFlag = ODM_RF_CALIBRATION | + ODM_RF_TX_PWR_TRACK; dm_odm->SupportAbility = pdmpriv->InitODMFlag; } static void Update_ODM_ComInfo_88E(struct adapter *Adapter) { - struct mlme_ext_priv *pmlmeext = &Adapter->mlmeextpriv; - struct mlme_priv *pmlmepriv = &Adapter->mlmepriv; + struct mlme_ext_priv *pmlmeext = &Adapter->mlmeextpriv; + struct mlme_priv *pmlmepriv = &Adapter->mlmepriv; struct pwrctrl_priv *pwrctrlpriv = &Adapter->pwrctrlpriv; struct hal_data_8188e *hal_data = Adapter->HalData; - struct odm_dm_struct *dm_odm = &(hal_data->odmpriv); - struct dm_priv *pdmpriv = &hal_data->dmpriv; + struct odm_dm_struct *dm_odm = &hal_data->odmpriv; + struct dm_priv *pdmpriv = &hal_data->dmpriv; int i; - pdmpriv->InitODMFlag = ODM_BB_DIG | - ODM_BB_RA_MASK | - ODM_BB_DYNAMIC_TXPWR | - ODM_BB_FA_CNT | - ODM_BB_RSSI_MONITOR | - ODM_BB_CCK_PD | - ODM_BB_PWR_SAVE | - ODM_MAC_EDCA_TURBO | - ODM_RF_CALIBRATION | - ODM_RF_TX_PWR_TRACK; + pdmpriv->InitODMFlag = ODM_BB_DIG | + ODM_BB_RA_MASK | + ODM_BB_DYNAMIC_TXPWR | + ODM_BB_FA_CNT | + ODM_BB_RSSI_MONITOR | + ODM_BB_CCK_PD | + ODM_BB_PWR_SAVE | + ODM_MAC_EDCA_TURBO | + ODM_RF_CALIBRATION | + ODM_RF_TX_PWR_TRACK; if (hal_data->AntDivCfg) pdmpriv->InitODMFlag |= ODM_BB_ANT_DIV; if (Adapter->registrypriv.mp_mode == 1) { - pdmpriv->InitODMFlag = ODM_RF_CALIBRATION | - ODM_RF_TX_PWR_TRACK; + pdmpriv->InitODMFlag = ODM_RF_CALIBRATION | + ODM_RF_TX_PWR_TRACK; } dm_odm->SupportAbility = pdmpriv->InitODMFlag; @@ -106,20 +108,23 @@ static void Update_ODM_ComInfo_88E(struct adapter *Adapter) dm_odm->pbPowerSaving = (bool *)&pwrctrlpriv->bpower_saving; dm_odm->AntDivType = hal_data->TRxAntDivType; - /* Tx power tracking BB swing table. */ - /* The base index = 12. +((12-n)/2)dB 13~?? = decrease tx pwr by -((n-12)/2)dB */ + /* Tx power tracking BB swing table. + * The base index = + * 12. +((12-n)/2)dB 13~?? = decrease tx pwr by -((n-12)/2)dB + */ dm_odm->BbSwingIdxOfdm = 12; /* Set defalut value as index 12. */ dm_odm->BbSwingIdxOfdmCurrent = 12; dm_odm->BbSwingFlagOfdm = false; for (i = 0; i < NUM_STA; i++) - ODM_CmnInfoPtrArrayHook(dm_odm, ODM_CMNINFO_STA_STATUS, i, NULL); + ODM_CmnInfoPtrArrayHook(dm_odm, ODM_CMNINFO_STA_STATUS, i, + NULL); } void rtl8188e_InitHalDm(struct adapter *Adapter) { - struct dm_priv *pdmpriv = &Adapter->HalData->dmpriv; - struct odm_dm_struct *dm_odm = &(Adapter->HalData->odmpriv); + struct dm_priv *pdmpriv = &Adapter->HalData->dmpriv; + struct odm_dm_struct *dm_odm = &Adapter->HalData->odmpriv; dm_InitGPIOSetting(Adapter); pdmpriv->DM_Type = DM_Type_ByDriver; @@ -162,7 +167,7 @@ skip_dm: void rtw_hal_dm_init(struct adapter *Adapter) { - struct dm_priv *pdmpriv = &Adapter->HalData->dmpriv; + struct dm_priv *pdmpriv = &Adapter->HalData->dmpriv; struct odm_dm_struct *podmpriv = &Adapter->HalData->odmpriv; memset(pdmpriv, 0, sizeof(struct dm_priv)); @@ -172,23 +177,28 @@ void rtw_hal_dm_init(struct adapter *Adapter) /* Add new function to reset the state of antenna diversity before link. */ /* Compare RSSI for deciding antenna */ -void rtw_hal_antdiv_rssi_compared(struct adapter *Adapter, struct wlan_bssid_ex *dst, struct wlan_bssid_ex *src) +void rtw_hal_antdiv_rssi_compared(struct adapter *Adapter, + struct wlan_bssid_ex *dst, + struct wlan_bssid_ex *src) { if (Adapter->HalData->AntDivCfg != 0) { - /* select optimum_antenna for before linked =>For antenna diversity */ - if (dst->Rssi >= src->Rssi) {/* keep org parameter */ + /* select optimum_antenna for before linked => For antenna + * diversity + */ + if (dst->Rssi >= src->Rssi) {/* keep org parameter */ src->Rssi = dst->Rssi; - src->PhyInfo.Optimum_antenna = dst->PhyInfo.Optimum_antenna; + src->PhyInfo.Optimum_antenna = + dst->PhyInfo.Optimum_antenna; } } } /* Add new function to reset the state of antenna diversity before link. */ -u8 rtw_hal_antdiv_before_linked(struct adapter *Adapter) +bool rtw_hal_antdiv_before_linked(struct adapter *Adapter) { struct odm_dm_struct *dm_odm = &Adapter->HalData->odmpriv; struct sw_ant_switch *dm_swat_tbl = &dm_odm->DM_SWAT_Table; - struct mlme_priv *pmlmepriv = &(Adapter->mlmepriv); + struct mlme_priv *pmlmepriv = &Adapter->mlmepriv; /* Condition that does not need to use antenna diversity. */ if (Adapter->HalData->AntDivCfg == 0) @@ -197,15 +207,16 @@ u8 rtw_hal_antdiv_before_linked(struct adapter *Adapter) if (check_fwstate(pmlmepriv, _FW_LINKED)) return false; - if (dm_swat_tbl->SWAS_NoLink_State == 0) { - /* switch channel */ - dm_swat_tbl->SWAS_NoLink_State = 1; - dm_swat_tbl->CurAntenna = (dm_swat_tbl->CurAntenna == Antenna_A) ? Antenna_B : Antenna_A; - - rtw_antenna_select_cmd(Adapter, dm_swat_tbl->CurAntenna, false); - return true; - } else { + if (dm_swat_tbl->SWAS_NoLink_State != 0) { dm_swat_tbl->SWAS_NoLink_State = 0; return false; } + + /* switch channel */ + dm_swat_tbl->SWAS_NoLink_State = 1; + dm_swat_tbl->CurAntenna = (dm_swat_tbl->CurAntenna == Antenna_A) ? + Antenna_B : Antenna_A; + + rtw_antenna_select_cmd(Adapter, dm_swat_tbl->CurAntenna, false); + return true; } diff --git a/drivers/staging/rtl8188eu/include/hal8188e_phy_cfg.h b/drivers/staging/rtl8188eu/include/hal8188e_phy_cfg.h index da66695a1d8f..0c5b2b0948f5 100644 --- a/drivers/staging/rtl8188eu/include/hal8188e_phy_cfg.h +++ b/drivers/staging/rtl8188eu/include/hal8188e_phy_cfg.h @@ -15,11 +15,6 @@ #define MAX_TXPWR_IDX_NMODE_92S 63 #define Reset_Cnt_Limit 3 -#define IQK_MAC_REG_NUM 4 -#define IQK_ADDA_REG_NUM 16 -#define IQK_BB_REG_NUM 9 -#define HP_THERMAL_NUM 8 - #define MAX_AGGR_NUM 0x07 diff --git a/drivers/staging/rtl8188eu/include/hal_intf.h b/drivers/staging/rtl8188eu/include/hal_intf.h index 516a89647003..39df30599a5d 100644 --- a/drivers/staging/rtl8188eu/include/hal_intf.h +++ b/drivers/staging/rtl8188eu/include/hal_intf.h @@ -209,7 +209,7 @@ void rtw_hal_set_bwmode(struct adapter *padapter, void rtw_hal_set_chan(struct adapter *padapter, u8 channel); void rtw_hal_dm_watchdog(struct adapter *padapter); -u8 rtw_hal_antdiv_before_linked(struct adapter *padapter); +bool rtw_hal_antdiv_before_linked(struct adapter *padapter); void rtw_hal_antdiv_rssi_compared(struct adapter *padapter, struct wlan_bssid_ex *dst, struct wlan_bssid_ex *src); diff --git a/drivers/staging/rtl8188eu/include/ieee80211.h b/drivers/staging/rtl8188eu/include/ieee80211.h index d569fe5ed8e6..75f0ebe0faf5 100644 --- a/drivers/staging/rtl8188eu/include/ieee80211.h +++ b/drivers/staging/rtl8188eu/include/ieee80211.h @@ -765,7 +765,7 @@ bool rtw_is_cckrates_included(u8 *rate); bool rtw_is_cckratesonly_included(u8 *rate); -int rtw_check_network_type(unsigned char *rate, int ratelen, int channel); +int rtw_check_network_type(unsigned char *rate); void rtw_get_bcn_info(struct wlan_network *pnetwork); diff --git a/drivers/staging/rtl8188eu/include/odm.h b/drivers/staging/rtl8188eu/include/odm.h index 8245cea2feef..9d39fe13626a 100644 --- a/drivers/staging/rtl8188eu/include/odm.h +++ b/drivers/staging/rtl8188eu/include/odm.h @@ -239,7 +239,6 @@ struct odm_rate_adapt { #define IQK_MAC_REG_NUM 4 #define IQK_ADDA_REG_NUM 16 -#define IQK_BB_REG_NUM_MAX 10 #define IQK_BB_REG_NUM 9 #define HP_THERMAL_NUM 8 diff --git a/drivers/staging/rtl8188eu/include/rtl8188e_dm.h b/drivers/staging/rtl8188eu/include/rtl8188e_dm.h index 19204335ab4c..910b982ab775 100644 --- a/drivers/staging/rtl8188eu/include/rtl8188e_dm.h +++ b/drivers/staging/rtl8188eu/include/rtl8188e_dm.h @@ -10,12 +10,7 @@ enum{ UP_LINK, DOWN_LINK, }; -/* duplicate code,will move to ODM ######### */ -#define IQK_MAC_REG_NUM 4 -#define IQK_ADDA_REG_NUM 16 -#define IQK_BB_REG_NUM 9 -#define HP_THERMAL_NUM 8 -/* duplicate code,will move to ODM ######### */ + struct dm_priv { u8 DM_Type; u8 DMFlag; diff --git a/drivers/staging/rtl8188eu/include/rtw_rf.h b/drivers/staging/rtl8188eu/include/rtw_rf.h index b5dfb226f32a..c3847cf16ec1 100644 --- a/drivers/staging/rtl8188eu/include/rtw_rf.h +++ b/drivers/staging/rtl8188eu/include/rtw_rf.h @@ -19,9 +19,6 @@ #define SHORT_SLOT_TIME 9 #define NON_SHORT_SLOT_TIME 20 -#define RTL8711_RF_MAX_SENS 6 -#define RTL8711_RF_DEF_SENS 4 - /* We now define the following channels as the max channels in each * channel plan. */ @@ -30,8 +27,6 @@ #define MAX_CHANNEL_NUM_2G 14 #define MAX_CHANNEL_NUM 14 /* 2.4 GHz only */ -#define NUM_REGULATORYS 1 - /* Country codes */ #define USA 0x555320 #define EUROPE 0x1 /* temp, should be provided later */ @@ -74,17 +69,6 @@ enum _REG_PREAMBLE_MODE { PREAMBLE_SHORT = 3, }; -enum _RTL8712_RF_MIMO_CONFIG_ { - RTL8712_RFCONFIG_1T = 0x10, - RTL8712_RFCONFIG_2T = 0x20, - RTL8712_RFCONFIG_1R = 0x01, - RTL8712_RFCONFIG_2R = 0x02, - RTL8712_RFCONFIG_1T1R = 0x11, - RTL8712_RFCONFIG_1T2R = 0x12, - RTL8712_RFCONFIG_TURBO = 0x92, - RTL8712_RFCONFIG_2T2R = 0x22 -}; - enum rf90_radio_path { RF90_PATH_A = 0, /* Radio Path A */ RF90_PATH_B = 1, /* Radio Path B */ diff --git a/drivers/staging/rtl8188eu/os_dep/ioctl_linux.c b/drivers/staging/rtl8188eu/os_dep/ioctl_linux.c index 710c33fd4965..9b6ea86d1dcf 100644 --- a/drivers/staging/rtl8188eu/os_dep/ioctl_linux.c +++ b/drivers/staging/rtl8188eu/os_dep/ioctl_linux.c @@ -222,18 +222,21 @@ static char *translate_scan(struct adapter *padapter, /* parsing WPA/WPA2 IE */ { - u8 buf[MAX_WPA_IE_LEN]; + u8 *buf; u8 wpa_ie[255], rsn_ie[255]; u16 wpa_len = 0, rsn_len = 0; u8 *p; + buf = kzalloc(MAX_WPA_IE_LEN, GFP_ATOMIC); + if (!buf) + return start; + rtw_get_sec_ie(pnetwork->network.ies, pnetwork->network.ie_length, rsn_ie, &rsn_len, wpa_ie, &wpa_len); RT_TRACE(_module_rtl871x_mlme_c_, _drv_info_, ("rtw_wx_get_scan: ssid =%s\n", pnetwork->network.ssid.ssid)); RT_TRACE(_module_rtl871x_mlme_c_, _drv_info_, ("rtw_wx_get_scan: wpa_len =%d rsn_len =%d\n", wpa_len, rsn_len)); if (wpa_len > 0) { p = buf; - memset(buf, 0, MAX_WPA_IE_LEN); p += sprintf(p, "wpa_ie="); for (i = 0; i < wpa_len; i++) p += sprintf(p, "%02x", wpa_ie[i]); @@ -250,7 +253,6 @@ static char *translate_scan(struct adapter *padapter, } if (rsn_len > 0) { p = buf; - memset(buf, 0, MAX_WPA_IE_LEN); p += sprintf(p, "rsn_ie="); for (i = 0; i < rsn_len; i++) p += sprintf(p, "%02x", rsn_ie[i]); @@ -264,6 +266,7 @@ static char *translate_scan(struct adapter *padapter, iwe.u.data.length = rsn_len; start = iwe_stream_add_point(info, start, stop, &iwe, rsn_ie); } + kfree(buf); } {/* parsing WPS IE */ @@ -593,9 +596,8 @@ static int rtw_set_wpa_ie(struct adapter *padapter, char *pie, unsigned short ie set_fwstate(&padapter->mlmepriv, WIFI_UNDER_WPS); cnt += buf[cnt+1]+2; break; - } else { - cnt += buf[cnt+1]+2; /* goto next */ } + cnt += buf[cnt+1]+2; /* goto next */ } } } @@ -770,8 +772,7 @@ static int rtw_wx_set_pmkid(struct net_device *dev, DBG_88E("[rtw_wx_set_pmkid] IW_PMKSA_ADD!\n"); if (!memcmp(strIssueBssid, strZeroMacAddress, ETH_ALEN)) return ret; - else - ret = true; + ret = true; blInserted = false; /* overwrite PMKID */ diff --git a/drivers/staging/rtl8192e/rtl8192e/rtl_core.c b/drivers/staging/rtl8192e/rtl8192e/rtl_core.c index 60c652793f93..11183b9f757a 100644 --- a/drivers/staging/rtl8192e/rtl8192e/rtl_core.c +++ b/drivers/staging/rtl8192e/rtl8192e/rtl_core.c @@ -1973,18 +1973,11 @@ u8 rtl92e_rx_db_to_percent(s8 antpower) u8 rtl92e_evm_db_to_percent(s8 value) { - s8 ret_val; + s8 ret_val = clamp(-value, 0, 33) * 3; - ret_val = value; - - if (ret_val >= 0) - ret_val = 0; - if (ret_val <= -33) - ret_val = -33; - ret_val = 0 - ret_val; - ret_val *= 3; if (ret_val == 99) ret_val = 100; + return ret_val; } diff --git a/drivers/staging/rtl8192u/Makefile b/drivers/staging/rtl8192u/Makefile index dcd51bf4aed3..0be7426b6ebc 100644 --- a/drivers/staging/rtl8192u/Makefile +++ b/drivers/staging/rtl8192u/Makefile @@ -1,13 +1,9 @@ # SPDX-License-Identifier: GPL-2.0 NIC_SELECT = RTL8192U -ccflags-y := -std=gnu89 -ccflags-y += -O2 - ccflags-y += -DCONFIG_FORCE_HARD_FLOAT=y ccflags-y += -DJACKSON_NEW_8187 -DJACKSON_NEW_RX ccflags-y += -DTHOMAS_BEACON -DTHOMAS_TASKLET -DTHOMAS_SKB -DTHOMAS_TURBO -ccflags-y += -I $(srctree)/$(src)/ieee80211 r8192u_usb-y := r8192U_core.o r8180_93cx6.o r8192U_wx.o \ r8190_rtl8256.o r819xU_phy.o r819xU_firmware.o \ diff --git a/drivers/staging/rtl8192u/ieee80211/Makefile b/drivers/staging/rtl8192u/ieee80211/Makefile deleted file mode 100644 index 0d4d6489f767..000000000000 --- a/drivers/staging/rtl8192u/ieee80211/Makefile +++ /dev/null @@ -1,27 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0 -NIC_SELECT = RTL8192U - -ccflags-y := -O2 -ccflags-y += -DJACKSON_NEW_8187 -DJACKSON_NEW_RX - -ieee80211-rsl-objs := ieee80211_rx.o \ - ieee80211_softmac.o \ - ieee80211_tx.o \ - ieee80211_wx.o \ - ieee80211_module.o \ - ieee80211_softmac_wx.o\ - rtl819x_HTProc.o\ - rtl819x_TSProc.o\ - rtl819x_BAProc.o\ - dot11d.o - -ieee80211_crypt-rsl-objs := ieee80211_crypt.o -ieee80211_crypt_tkip-rsl-objs := ieee80211_crypt_tkip.o -ieee80211_crypt_ccmp-rsl-objs := ieee80211_crypt_ccmp.o -ieee80211_crypt_wep-rsl-objs := ieee80211_crypt_wep.o - -obj-m +=ieee80211-rsl.o -obj-m +=ieee80211_crypt-rsl.o -obj-m +=ieee80211_crypt_wep-rsl.o -obj-m +=ieee80211_crypt_tkip-rsl.o -obj-m +=ieee80211_crypt_ccmp-rsl.o diff --git a/drivers/staging/rtl8192u/ieee80211/ieee80211_rx.c b/drivers/staging/rtl8192u/ieee80211/ieee80211_rx.c index 00fea127bdc3..e101f7b13c7e 100644 --- a/drivers/staging/rtl8192u/ieee80211/ieee80211_rx.c +++ b/drivers/staging/rtl8192u/ieee80211/ieee80211_rx.c @@ -232,8 +232,7 @@ ieee80211_rx_frame_mgmt(struct ieee80211_device *ieee, struct sk_buff *skb, #ifdef NOT_YET if (ieee->iw_mode == IW_MODE_MASTER) { - printk(KERN_DEBUG "%s: Master mode not yet supported.\n", - ieee->dev->name); + netdev_dbg(ieee->dev, "Master mode not yet supported.\n"); return 0; /* hostap_update_sta_ps(ieee, (struct hostap_ieee80211_hdr_4addr *) @@ -261,9 +260,9 @@ ieee80211_rx_frame_mgmt(struct ieee80211_device *ieee, struct sk_buff *skb, if (ieee->iw_mode == IW_MODE_MASTER) { if (type != WLAN_FC_TYPE_MGMT && type != WLAN_FC_TYPE_CTRL) { - printk(KERN_DEBUG "%s: unknown management frame " + netdev_dbg(skb->dev, "unknown management frame " "(type=0x%02x, stype=0x%02x) dropped\n", - skb->dev->name, type, stype); + type, stype); return -1; } @@ -271,8 +270,8 @@ ieee80211_rx_frame_mgmt(struct ieee80211_device *ieee, struct sk_buff *skb, return 0; } - printk(KERN_DEBUG "%s: hostap_rx_frame_mgmt: management frame " - "received in non-Host AP mode\n", skb->dev->name); + netdev_dbg(skb->dev, "hostap_rx_frame_mgmt: management frame " + "received in non-Host AP mode\n"); return -1; #endif } @@ -349,9 +348,9 @@ ieee80211_rx_frame_decrypt(struct ieee80211_device *ieee, struct sk_buff *skb, if (ieee->tkip_countermeasures && strcmp(crypt->ops->name, "TKIP") == 0) { if (net_ratelimit()) { - printk(KERN_DEBUG "%s: TKIP countermeasures: dropped " + netdev_dbg(ieee->dev, "TKIP countermeasures: dropped " "received packet from %pM\n", - ieee->dev->name, hdr->addr2); + hdr->addr2); } return -1; } @@ -397,9 +396,9 @@ ieee80211_rx_frame_decrypt_msdu(struct ieee80211_device *ieee, struct sk_buff *s res = crypt->ops->decrypt_msdu(skb, keyidx, hdrlen, crypt->priv); atomic_dec(&crypt->refcnt); if (res < 0) { - printk(KERN_DEBUG "%s: MSDU decryption/MIC verification failed" + netdev_dbg(ieee->dev, "MSDU decryption/MIC verification failed" " (SA=%pM keyidx=%d)\n", - ieee->dev->name, hdr->addr2, keyidx); + hdr->addr2, keyidx); return -1; } @@ -749,7 +748,8 @@ static void RxReorderIndicatePacket(struct ieee80211_device *ieee, kfree(prxbIndicateArray); } -static u8 parse_subframe(struct sk_buff *skb, +static u8 parse_subframe(struct ieee80211_device *ieee, + struct sk_buff *skb, struct ieee80211_rx_stats *rx_stats, struct ieee80211_rxb *rxb, u8 *src, u8 *dst) { @@ -810,11 +810,11 @@ static u8 parse_subframe(struct sk_buff *skb, nSubframe_Length = (nSubframe_Length >> 8) + (nSubframe_Length << 8); if (skb->len < (ETHERNET_HEADER_SIZE + nSubframe_Length)) { - printk("%s: A-MSDU parse error!! pRfd->nTotalSubframe : %d\n",\ - __func__, rxb->nr_subframes); - printk("%s: A-MSDU parse error!! Subframe Length: %d\n", __func__, nSubframe_Length); - printk("nRemain_Length is %d and nSubframe_Length is : %d\n", skb->len, nSubframe_Length); - printk("The Packet SeqNum is %d\n", SeqNum); + netdev_dbg(ieee->dev, "A-MSDU parse error!! pRfd->nTotalSubframe : %d\n", + rxb->nr_subframes); + netdev_dbg(ieee->dev, "A-MSDU parse error!! Subframe Length: %d\n", nSubframe_Length); + netdev_dbg(ieee->dev, "nRemain_Length is %d and nSubframe_Length is : %d\n", skb->len, nSubframe_Length); + netdev_dbg(ieee->dev, "The Packet SeqNum is %d\n", SeqNum); return 0; } @@ -904,8 +904,7 @@ int ieee80211_rx(struct ieee80211_device *ieee, struct sk_buff *skb, stats = &ieee->stats; if (skb->len < 10) { - printk(KERN_INFO "%s: SKB length < 10\n", - dev->name); + netdev_info(dev, "SKB length < 10\n"); goto rx_dropped; } @@ -919,7 +918,7 @@ int ieee80211_rx(struct ieee80211_device *ieee, struct sk_buff *skb, if (HTCCheck(ieee, skb->data)) { if (net_ratelimit()) - printk("find HTCControl\n"); + netdev_warn(dev, "find HTCControl\n"); hdrlen += 4; rx_stats->bContainHTC = true; } @@ -1113,7 +1112,7 @@ int ieee80211_rx(struct ieee80211_device *ieee, struct sk_buff *skb, if (ieee->host_decrypt && (fc & IEEE80211_FCTL_WEP) && (keyidx = ieee80211_rx_frame_decrypt(ieee, skb, crypt)) < 0) { - printk("decrypt frame error\n"); + netdev_dbg(ieee->dev, "decrypt frame error\n"); goto rx_dropped; } @@ -1141,9 +1140,8 @@ int ieee80211_rx(struct ieee80211_device *ieee, struct sk_buff *skb, flen -= hdrlen; if (frag_skb->tail + flen > frag_skb->end) { - printk(KERN_WARNING "%s: host decrypted and " - "reassembled frame did not fit skb\n", - dev->name); + netdev_warn(dev, "host decrypted and " + "reassembled frame did not fit skb\n"); ieee80211_frag_cache_invalidate(ieee, hdr); goto rx_dropped; } @@ -1178,7 +1176,7 @@ int ieee80211_rx(struct ieee80211_device *ieee, struct sk_buff *skb, * encrypted/authenticated */ if (ieee->host_decrypt && (fc & IEEE80211_FCTL_WEP) && ieee80211_rx_frame_decrypt_msdu(ieee, skb, keyidx, crypt)) { - printk("==>decrypt msdu error\n"); + netdev_dbg(ieee->dev, "==>decrypt msdu error\n"); goto rx_dropped; } @@ -1250,7 +1248,7 @@ int ieee80211_rx(struct ieee80211_device *ieee, struct sk_buff *skb, goto rx_dropped; /* to parse amsdu packets */ /* qos data packets & reserved bit is 1 */ - if (parse_subframe(skb, rx_stats, rxb, src, dst) == 0) { + if (parse_subframe(ieee, skb, rx_stats, rxb, src, dst) == 0) { /* only to free rxb, and not submit the packets to upper layer */ for (i = 0; i < rxb->nr_subframes; i++) { dev_kfree_skb(rxb->subframes[i]); @@ -1863,7 +1861,7 @@ int ieee80211_parse_info_param(struct ieee80211_device *ieee, info_element->data[0] == 0x00 && info_element->data[1] == 0x13 && info_element->data[2] == 0x74)) { - printk("========>%s(): athros AP is exist\n", __func__); + netdev_dbg(ieee->dev, "========> athros AP is exist\n"); network->atheros_cap_exist = true; } else network->atheros_cap_exist = false; @@ -1980,8 +1978,8 @@ int ieee80211_parse_info_param(struct ieee80211_device *ieee, } break; case MFIE_TYPE_QOS_PARAMETER: - printk(KERN_ERR - "QoS Error need to parse QOS_PARAMETER IE\n"); + netdev_err(ieee->dev, + "QoS Error need to parse QOS_PARAMETER IE\n"); break; case MFIE_TYPE_COUNTRY: @@ -2357,14 +2355,14 @@ static inline void ieee80211_process_probe_response( if (IS_COUNTRY_IE_VALID(ieee)) { // Case 1: Country code if (!is_legal_channel(ieee, network->channel)) { - printk("GetScanInfo(): For Country code, filter probe response at channel(%d).\n", network->channel); + netdev_warn(ieee->dev, "GetScanInfo(): For Country code, filter probe response at channel(%d).\n", network->channel); goto out; } } else { // Case 2: No any country code. // Filter over channel ch12~14 if (network->channel > 11) { - printk("GetScanInfo(): For Global Domain, filter probe response at channel(%d).\n", network->channel); + netdev_warn(ieee->dev, "GetScanInfo(): For Global Domain, filter probe response at channel(%d).\n", network->channel); goto out; } } @@ -2372,14 +2370,14 @@ static inline void ieee80211_process_probe_response( if (IS_COUNTRY_IE_VALID(ieee)) { // Case 1: Country code if (!is_legal_channel(ieee, network->channel)) { - printk("GetScanInfo(): For Country code, filter beacon at channel(%d).\n", network->channel); + netdev_warn(ieee->dev, "GetScanInfo(): For Country code, filter beacon at channel(%d).\n", network->channel); goto out; } } else { // Case 2: No any country code. // Filter over channel ch12~14 if (network->channel > 14) { - printk("GetScanInfo(): For Global Domain, filter beacon at channel(%d).\n", network->channel); + netdev_warn(ieee->dev, "GetScanInfo(): For Global Domain, filter beacon at channel(%d).\n", network->channel); goto out; } } diff --git a/drivers/staging/rtl8192u/r8192U_core.c b/drivers/staging/rtl8192u/r8192U_core.c index 482382a887f8..89dd1fb0b38d 100644 --- a/drivers/staging/rtl8192u/r8192U_core.c +++ b/drivers/staging/rtl8192u/r8192U_core.c @@ -60,7 +60,7 @@ double __extendsfdf2(float a) #include <linux/seq_file.h> /* FIXME: check if 2.6.7 is ok */ -#include "dot11d.h" +#include "ieee80211/dot11d.h" /* set here to open your trace code. */ u32 rt_global_debug_component = COMP_DOWN | COMP_SEC | @@ -3954,18 +3954,11 @@ static u8 rtl819x_query_rxpwrpercentage(s8 antpower) static u8 rtl819x_evm_dbtopercentage(s8 value) { - s8 ret_val; + s8 ret_val = clamp(-value, 0, 33) * 3; - ret_val = value; - - if (ret_val >= 0) - ret_val = 0; - if (ret_val <= -33) - ret_val = -33; - ret_val = 0 - ret_val; - ret_val *= 3; if (ret_val == 99) ret_val = 100; + return ret_val; } diff --git a/drivers/staging/rtl8192u/r8192U_wx.c b/drivers/staging/rtl8192u/r8192U_wx.c index 5822bb7984b9..0118edb0b9ab 100644 --- a/drivers/staging/rtl8192u/r8192U_wx.c +++ b/drivers/staging/rtl8192u/r8192U_wx.c @@ -23,7 +23,7 @@ #include "r8192U.h" #include "r8192U_hw.h" -#include "dot11d.h" +#include "ieee80211/dot11d.h" #include "r8192U_wx.h" #define RATE_COUNT 12 diff --git a/drivers/staging/rtl8192u/r819xU_phy.c b/drivers/staging/rtl8192u/r819xU_phy.c index c04d8eca0cfb..555e52522be6 100644 --- a/drivers/staging/rtl8192u/r819xU_phy.c +++ b/drivers/staging/rtl8192u/r819xU_phy.c @@ -7,7 +7,7 @@ #include "r8192U_dm.h" #include "r819xU_firmware_img.h" -#include "dot11d.h" +#include "ieee80211/dot11d.h" #include <linux/bitops.h> static u32 RF_CHANNEL_TABLE_ZEBRA[] = { diff --git a/drivers/staging/rtl8712/rtl8712_recv.c b/drivers/staging/rtl8712/rtl8712_recv.c index 00ea0beb12c9..116773943a2e 100644 --- a/drivers/staging/rtl8712/rtl8712_recv.c +++ b/drivers/staging/rtl8712/rtl8712_recv.c @@ -663,17 +663,11 @@ static u8 evm_db2percentage(s8 value) /* * -33dB~0dB to 0%~99% */ - s8 ret_val; + s8 ret_val = clamp(-value, 0, 33) * 3; - ret_val = value; - if (ret_val >= 0) - ret_val = 0; - if (ret_val <= -33) - ret_val = -33; - ret_val = -ret_val; - ret_val *= 3; if (ret_val == 99) ret_val = 100; + return ret_val; } diff --git a/drivers/staging/rtl8723bs/core/rtw_mlme_ext.c b/drivers/staging/rtl8723bs/core/rtw_mlme_ext.c index 5e687f6d2c3e..c642825ca8ef 100644 --- a/drivers/staging/rtl8723bs/core/rtw_mlme_ext.c +++ b/drivers/staging/rtl8723bs/core/rtw_mlme_ext.c @@ -207,10 +207,10 @@ static RT_CHANNEL_PLAN_MAP RTW_ChannelPlanMap[RT_CHANNEL_DOMAIN_MAX] = { {0x02, 0x1F}, /* 0x57, RT_CHANNEL_DOMAIN_FCC1_FCC10 */ }; -static RT_CHANNEL_PLAN_MAP RTW_CHANNEL_PLAN_MAP_REALTEK_DEFINE = {0x03, 0x02}; /* use the conbination for max channel numbers */ + /* use the combination for max channel numbers */ +static RT_CHANNEL_PLAN_MAP RTW_CHANNEL_PLAN_MAP_REALTEK_DEFINE = {0x03, 0x02}; -/* - * Search the @param ch in given @param ch_set +/* Search the @param ch in given @param ch_set * @ch_set: the given channel set * @ch: the given channel number * @@ -229,8 +229,7 @@ int rtw_ch_set_search_ch(RT_CHANNEL_INFO *ch_set, const u32 ch) return i; } -/* - * Check the @param ch is fit with setband setting of @param adapter +/* Check the @param ch is fit with setband setting of @param adapter * @adapter: the given adapter * @ch: the given channel number * @@ -2265,7 +2264,7 @@ inline struct xmit_frame *alloc_mgtxmitframe(struct xmit_priv *pxmitpriv) /**************************************************************************** -Following are some TX fuctions for WiFi MLME +Following are some TX functions for WiFi MLME *****************************************************************************/ @@ -2956,7 +2955,7 @@ exit: return ret; } -/* if psta == NULL, indiate we are station(client) now... */ +/* if psta == NULL, indicate we are station(client) now... */ void issue_auth(struct adapter *padapter, struct sta_info *psta, unsigned short status) { struct xmit_frame *pmgntframe; @@ -3356,9 +3355,11 @@ void issue_assocreq(struct adapter *padapter) (!memcmp(pIE->data, WPS_OUI, 4))) { vs_ie_length = pIE->Length; if ((!padapter->registrypriv.wifi_spec) && (!memcmp(pIE->data, WPS_OUI, 4))) { - /* Commented by Kurt 20110629 */ - /* In some older APs, WPS handshake */ - /* would be fail if we append vender extensions informations to AP */ + /* Commented by Kurt 20110629 + * In some older APs, WPS handshake + * would be fail if we append vendor + * extensions information to AP + */ vs_ie_length = 14; } @@ -3406,7 +3407,7 @@ exit: rtw_buf_free(&pmlmepriv->assoc_req, &pmlmepriv->assoc_req_len); } -/* when wait_ack is ture, this function shoule be called at process context */ +/* when wait_ack is true, this function should be called at process context */ static int _issue_nulldata(struct adapter *padapter, unsigned char *da, unsigned int power_mode, bool wait_ack) { @@ -3481,7 +3482,7 @@ exit: /* * [IMPORTANT] Don't call this function in interrupt context * - * When wait_ms > 0, this function shoule be called at process context + * When wait_ms > 0, this function should be called at process context * da == NULL for station mode */ int issue_nulldata(struct adapter *padapter, unsigned char *da, unsigned int power_mode, int try_cnt, int wait_ms) @@ -3493,7 +3494,7 @@ int issue_nulldata(struct adapter *padapter, unsigned char *da, unsigned int pow struct sta_info *psta; - /* da == NULL, assum it's null data for sta to ap*/ + /* da == NULL, assume it's null data for sta to ap*/ if (!da) da = get_my_bssid(&(pmlmeinfo->network)); @@ -3558,14 +3559,14 @@ s32 issue_nulldata_in_interrupt(struct adapter *padapter, u8 *da) pmlmeext = &padapter->mlmeextpriv; pmlmeinfo = &pmlmeext->mlmext_info; - /* da == NULL, assum it's null data for sta to ap*/ + /* da == NULL, assume it's null data for sta to ap*/ if (!da) da = get_my_bssid(&(pmlmeinfo->network)); return _issue_nulldata(padapter, da, 0, false); } -/* when wait_ack is ture, this function shoule be called at process context */ +/* when wait_ack is true, this function should be called at process context */ static int _issue_qos_nulldata(struct adapter *padapter, unsigned char *da, u16 tid, bool wait_ack) { @@ -3644,7 +3645,7 @@ exit: return ret; } -/* when wait_ms >0 , this function shoule be called at process context */ +/* when wait_ms >0 , this function should be called at process context */ /* da == NULL for station mode */ int issue_qos_nulldata(struct adapter *padapter, unsigned char *da, u16 tid, int try_cnt, int wait_ms) { @@ -3653,7 +3654,7 @@ int issue_qos_nulldata(struct adapter *padapter, unsigned char *da, u16 tid, int struct mlme_ext_priv *pmlmeext = &(padapter->mlmeextpriv); struct mlme_ext_info *pmlmeinfo = &(pmlmeext->mlmext_info); - /* da == NULL, assum it's null data for sta to ap*/ + /* da == NULL, assume it's null data for sta to ap*/ if (!da) da = get_my_bssid(&(pmlmeinfo->network)); @@ -4264,7 +4265,7 @@ unsigned int send_beacon(struct adapter *padapter) /**************************************************************************** -Following are some utitity fuctions for WiFi MLME +Following are some utility functions for WiFi MLME *****************************************************************************/ @@ -4568,7 +4569,7 @@ u8 collect_bss_info(struct adapter *padapter, union recv_frame *precv_frame, str } #endif - /* mark bss info receving from nearby channel as SignalQuality 101 */ + /* mark bss info receiving from nearby channel as SignalQuality 101 */ if (bssid->Configuration.DSConfig != rtw_get_oper_ch(padapter)) bssid->PhyInfo.SignalQuality = 101; @@ -4589,7 +4590,7 @@ void start_create_ibss(struct adapter *padapter) /* update wireless mode */ update_wireless_mode(padapter); - /* udpate capability */ + /* update capability */ caps = rtw_get_capability((struct wlan_bssid_ex *)pnetwork); update_capinfo(padapter, caps); if (caps&cap_IBSS) {/* adhoc master */ @@ -4644,7 +4645,7 @@ void start_clnt_join(struct adapter *padapter) /* update wireless mode */ update_wireless_mode(padapter); - /* udpate capability */ + /* update capability */ caps = rtw_get_capability((struct wlan_bssid_ex *)pnetwork); update_capinfo(padapter, caps); if (caps&cap_ESS) { @@ -5379,8 +5380,7 @@ static void rtw_mlmeext_disconnect(struct adapter *padapter) /* set_opmode_cmd(padapter, infra_client_with_mlme); */ - /* - * For safety, prevent from keeping macid sleep. + /* For safety, prevent from keeping macid sleep. * If we can sure all power mode enter/leave are paired, * this check can be removed. * Lucas@20131113 @@ -5441,7 +5441,7 @@ void mlmeext_joinbss_event_callback(struct adapter *padapter, int join_res) /* turn on dynamic functions */ Switch_DM_Func(padapter, DYNAMIC_ALL_FUNC_ENABLE, true); - /* update IOT-releated issue */ + /* update IOT-related issue */ update_IOT_info(padapter); rtw_hal_set_hwreg(padapter, HW_VAR_BASIC_RATE, cur_network->SupportedRates); @@ -5449,7 +5449,7 @@ void mlmeext_joinbss_event_callback(struct adapter *padapter, int join_res) /* BCN interval */ rtw_hal_set_hwreg(padapter, HW_VAR_BEACON_INTERVAL, (u8 *)(&pmlmeinfo->bcn_interval)); - /* udpate capability */ + /* update capability */ update_capinfo(padapter, pmlmeinfo->capability); /* WMM, Update EDCA param */ @@ -6385,7 +6385,9 @@ u8 sitesurvey_cmd_hdl(struct adapter *padapter, u8 *pbuf) Save_DM_Func_Flag(padapter); Switch_DM_Func(padapter, DYNAMIC_FUNC_DISABLE, false); - /* config the initial gain under scaning, need to write the BB registers */ + /* config the initial gain under scanning, need to write the BB + * registers + */ initialgain = 0x1e; rtw_hal_set_hwreg(padapter, HW_VAR_INITIAL_GAIN, (u8 *)(&initialgain)); diff --git a/drivers/staging/rtl8723bs/hal/HalPhyRf.c b/drivers/staging/rtl8723bs/hal/HalPhyRf.c index beb4002a40e1..357802db9aed 100644 --- a/drivers/staging/rtl8723bs/hal/HalPhyRf.c +++ b/drivers/staging/rtl8723bs/hal/HalPhyRf.c @@ -622,33 +622,3 @@ void ODM_TXPowerTrackingCallback_ThermalMeter(struct adapter *Adapter) pDM_Odm->RFCalibrateInfo.TXPowercount = 0; } - - - - -/* 3 ============================================================ */ -/* 3 IQ Calibration */ -/* 3 ============================================================ */ - -u8 ODM_GetRightChnlPlaceforIQK(u8 chnl) -{ - u8 channel_all[ODM_TARGET_CHNL_NUM_2G_5G] = { - 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, - 36, 38, 40, 42, 44, 46, 48, 50, 52, 54, 56, 58, - 60, 62, 64, 100, 102, 104, 106, 108, 110, 112, - 114, 116, 118, 120, 122, 124, 126, 128, 130, 132, - 134, 136, 138, 140, 149, 151, 153, 155, 157, 159, - 161, 163, 165 - }; - u8 place = chnl; - - - if (chnl > 14) { - for (place = 14; place < sizeof(channel_all); place++) { - if (channel_all[place] == chnl) - return place-13; - } - } - return 0; - -} diff --git a/drivers/staging/rtl8723bs/hal/HalPhyRf.h b/drivers/staging/rtl8723bs/hal/HalPhyRf.h index 3d6f68bc61d7..643fcf37c9ad 100644 --- a/drivers/staging/rtl8723bs/hal/HalPhyRf.h +++ b/drivers/staging/rtl8723bs/hal/HalPhyRf.h @@ -44,12 +44,4 @@ void ODM_ClearTxPowerTrackingState(PDM_ODM_T pDM_Odm); void ODM_TXPowerTrackingCallback_ThermalMeter(struct adapter *Adapter); - - -#define ODM_TARGET_CHNL_NUM_2G_5G 59 - - -u8 ODM_GetRightChnlPlaceforIQK(u8 chnl); - - #endif /* #ifndef __HAL_PHY_RF_H__ */ diff --git a/drivers/staging/rtl8723bs/hal/HalPhyRf_8723B.c b/drivers/staging/rtl8723bs/hal/HalPhyRf_8723B.c index 1ca9063a269f..85ea535dd6e9 100644 --- a/drivers/staging/rtl8723bs/hal/HalPhyRf_8723B.c +++ b/drivers/staging/rtl8723bs/hal/HalPhyRf_8723B.c @@ -1,5 +1,5 @@ // SPDX-License-Identifier: GPL-2.0 -/****************************************************************************** +/***************************************************************************** * * Copyright(c) 2007 - 2011 Realtek Corporation. All rights reserved. * @@ -82,7 +82,9 @@ static void setIqkMatrix_8723B( /* if (RFPath == ODM_RF_PATH_A) */ switch (RFPath) { case ODM_RF_PATH_A: - /* wirte new elements A, C, D to regC80 and regC94, element B is always 0 */ + /* write new elements A, C, D to regC80 and regC94, + * element B is always 0 + */ value32 = (ele_D<<22)|((ele_C&0x3F)<<16)|ele_A; PHY_SetBBReg(pDM_Odm->Adapter, rOFDM0_XATxIQImbalance, bMaskDWord, value32); @@ -93,7 +95,9 @@ static void setIqkMatrix_8723B( PHY_SetBBReg(pDM_Odm->Adapter, rOFDM0_ECCAThreshold, BIT24, value32); break; case ODM_RF_PATH_B: - /* wirte new elements A, C, D to regC88 and regC9C, element B is always 0 */ + /* write new elements A, C, D to regC88 and regC9C, + * element B is always 0 + */ value32 = (ele_D<<22)|((ele_C&0x3F)<<16)|ele_A; PHY_SetBBReg(pDM_Odm->Adapter, rOFDM0_XBTxIQImbalance, bMaskDWord, value32); @@ -166,7 +170,7 @@ void DoIQK_8723B( /*----------------------------------------------------------------------------- * Function: odm_TxPwrTrackSetPwr88E() * - * Overview: 88E change all channel tx power accordign to flag. + * Overview: 88E change all channel tx power according to flag. * OFDM & CCK are all different. * * Input: NONE @@ -1788,7 +1792,7 @@ void PHY_IQCalibrate_8723B( PDM_ODM_T pDM_Odm = &pHalData->odmpriv; s32 result[4][8]; /* last is final result */ - u8 i, final_candidate, Indexforchannel; + u8 i, final_candidate; bool bPathAOK, bPathBOK; s32 RegE94, RegE9C, RegEA4, RegEAC, RegEB4, RegEBC, RegEC4, RegECC, RegTmp = 0; bool is12simular, is13simular, is23simular; @@ -1993,17 +1997,14 @@ void PHY_IQCalibrate_8723B( _PHY_PathBFillIQKMatrix8723B(padapter, bPathBOK, result, final_candidate, (RegEC4 == 0)); } - Indexforchannel = ODM_GetRightChnlPlaceforIQK(pHalData->CurrentChannel); - /* To Fix BSOD when final_candidate is 0xff */ /* by sherry 20120321 */ if (final_candidate < 4) { for (i = 0; i < IQK_Matrix_REG_NUM; i++) - pDM_Odm->RFCalibrateInfo.IQKMatrixRegSetting[Indexforchannel].Value[0][i] = result[final_candidate][i]; - pDM_Odm->RFCalibrateInfo.IQKMatrixRegSetting[Indexforchannel].bIQKDone = true; + pDM_Odm->RFCalibrateInfo.IQKMatrixRegSetting[0].Value[0][i] = result[final_candidate][i]; + pDM_Odm->RFCalibrateInfo.IQKMatrixRegSetting[0].bIQKDone = true; } - /* RT_DISP(FINIT, INIT_IQK, ("\nIQK OK Indexforchannel %d.\n", Indexforchannel)); */ - ODM_RT_TRACE(pDM_Odm, ODM_COMP_CALIBRATION, ODM_DBG_LOUD, ("\nIQK OK Indexforchannel %d.\n", Indexforchannel)); + ODM_RT_TRACE(pDM_Odm, ODM_COMP_CALIBRATION, ODM_DBG_LOUD, ("\nIQK OK Indexforchannel %d.\n", 0)); _PHY_SaveADDARegisters8723B(padapter, IQK_BB_REG_92C, pDM_Odm->RFCalibrateInfo.IQK_BB_backup_recover, 9); diff --git a/drivers/staging/rtl8723bs/hal/rtl8723b_hal_init.c b/drivers/staging/rtl8723bs/hal/rtl8723b_hal_init.c index 66127f6c8e4d..de8caa6cd418 100644 --- a/drivers/staging/rtl8723bs/hal/rtl8723b_hal_init.c +++ b/drivers/staging/rtl8723bs/hal/rtl8723b_hal_init.c @@ -750,7 +750,7 @@ static void Hal_BT_EfusePowerSwitch( rtw_write8(padapter, 0x6B, tempval); /* Attention!! Between 0x6A[14] and 0x6A[15] setting need 100us delay */ - /* So don't wirte 0x6A[14]= 1 and 0x6A[15]= 0 together! */ + /* So don't write 0x6A[14]= 1 and 0x6A[15]= 0 together! */ msleep(1); /* disable BT output isolation */ /* 0x6A[15] = 0 */ @@ -765,7 +765,7 @@ static void Hal_BT_EfusePowerSwitch( rtw_write8(padapter, 0x6B, tempval); /* Attention!! Between 0x6A[14] and 0x6A[15] setting need 100us delay */ - /* So don't wirte 0x6A[14]= 1 and 0x6A[15]= 0 together! */ + /* So don't write 0x6A[14]= 1 and 0x6A[15]= 0 together! */ /* disable BT power cut */ /* 0x6A[14] = 1 */ @@ -1231,7 +1231,7 @@ static u16 hal_EfuseGetCurrentSize_WiFi( goto exit; error: - /* report max size to prevent wirte efuse */ + /* report max size to prevent write efuse */ EFUSE_GetEfuseDefinition(padapter, EFUSE_WIFI, TYPE_AVAILABLE_EFUSE_BYTES_TOTAL, &efuse_addr, bPseudoTest); exit: @@ -2237,7 +2237,7 @@ void rtl8723b_InitAntenna_Selection(struct adapter *padapter) u8 val; val = rtw_read8(padapter, REG_LEDCFG2); - /* Let 8051 take control antenna settting */ + /* Let 8051 take control antenna setting */ val |= BIT(7); /* DPDT_SEL_EN, 0x4C[23] */ rtw_write8(padapter, REG_LEDCFG2, val); } @@ -3191,22 +3191,26 @@ static void rtl8723b_fill_default_txdesc( if (bmcst) ptxdesc->bmc = 1; - /* 2009.11.05. tynli_test. Suggested by SD4 Filen for FW LPS. */ - /* (1) The sequence number of each non-Qos frame / broadcast / multicast / */ - /* mgnt frame should be controled by Hw because Fw will also send null data */ - /* which we cannot control when Fw LPS enable. */ - /* --> default enable non-Qos data sequense number. 2010.06.23. by tynli. */ - /* (2) Enable HW SEQ control for beacon packet, because we use Hw beacon. */ - /* (3) Use HW Qos SEQ to control the seq num of Ext port non-Qos packets. */ - /* 2010.06.23. Added by tynli. */ + /* 2009.11.05. tynli_test. Suggested by SD4 Filen for FW LPS. + * (1) The sequence number of each non-Qos frame / broadcast / + * multicast / mgnt frame should be controlled by Hw because Fw + * will also send null data which we cannot control when Fw LPS + * enable. + * --> default enable non-Qos data sequense number. 2010.06.23. + * by tynli. + * (2) Enable HW SEQ control for beacon packet, because we use + * Hw beacon. + * (3) Use HW Qos SEQ to control the seq num of Ext port non-Qos + * packets. + * 2010.06.23. Added by tynli. + */ if (!pattrib->qos_en) /* Hw set sequence number */ ptxdesc->en_hwseq = 1; /* HWSEQ_EN */ } -/* - *Description: +/* Description: * - *Parameters: + * Parameters: * pxmitframe xmitframe * pbuf where to fill tx desc */ @@ -3543,7 +3547,7 @@ static void hw_var_set_mlme_sitesurvey(struct adapter *padapter, u8 variable, u8 rtw_write8(padapter, reg_bcn_ctl, val8); } - /* Save orignal RRSR setting. */ + /* Save original RRSR setting. */ pHalData->RegRRSR = rtw_read16(padapter, REG_RRSR); } else { /* sitesurvey done */ @@ -3561,7 +3565,7 @@ static void hw_var_set_mlme_sitesurvey(struct adapter *padapter, u8 variable, u8 value_rcr |= rcr_clear_bit; rtw_write32(padapter, REG_RCR, value_rcr); - /* Restore orignal RRSR setting. */ + /* Restore original RRSR setting. */ rtw_write16(padapter, REG_RRSR, pHalData->RegRRSR); } } @@ -4329,8 +4333,7 @@ void GetHwReg8723B(struct adapter *padapter, u8 variable, u8 *val) } } -/* - *Description: +/* Description: * Change default setting of specified variable. */ u8 SetHalDefVar8723B(struct adapter *padapter, enum HAL_DEF_VARIABLE variable, void *pval) @@ -4348,8 +4351,7 @@ u8 SetHalDefVar8723B(struct adapter *padapter, enum HAL_DEF_VARIABLE variable, v return bResult; } -/* - *Description: +/* Description: * Query setting of specified variable. */ u8 GetHalDefVar8723B(struct adapter *padapter, enum HAL_DEF_VARIABLE variable, void *pval) diff --git a/drivers/staging/rts5208/Makefile b/drivers/staging/rts5208/Makefile index 6a934c41c738..3c9e9797d3d9 100644 --- a/drivers/staging/rts5208/Makefile +++ b/drivers/staging/rts5208/Makefile @@ -1,7 +1,5 @@ # SPDX-License-Identifier: GPL-2.0 obj-$(CONFIG_RTS5208) := rts5208.o -ccflags-y := -Idrivers/scsi - rts5208-y := rtsx.o rtsx_chip.o rtsx_transport.o rtsx_scsi.o \ rtsx_card.o general.o sd.o xd.o ms.o spi.o diff --git a/drivers/staging/rts5208/rtsx.c b/drivers/staging/rts5208/rtsx.c index fbb42e5258fd..be0053c795b7 100644 --- a/drivers/staging/rts5208/rtsx.c +++ b/drivers/staging/rts5208/rtsx.c @@ -831,7 +831,8 @@ static int rtsx_probe(struct pci_dev *pci, host = scsi_host_alloc(&rtsx_host_template, sizeof(*dev)); if (!host) { dev_err(&pci->dev, "Unable to allocate the scsi host\n"); - return -ENOMEM; + err = -ENOMEM; + goto scsi_host_alloc_fail; } dev = host_to_rtsx(host); @@ -971,7 +972,8 @@ ioremap_fail: kfree(dev->chip); chip_alloc_fail: dev_err(&pci->dev, "%s failed\n", __func__); - +scsi_host_alloc_fail: + pci_release_regions(pci); return err; } @@ -983,6 +985,7 @@ static void rtsx_remove(struct pci_dev *pci) quiesce_and_remove_host(dev); release_everything(dev); + pci_release_regions(pci); } /* PCI IDs */ diff --git a/drivers/staging/vc04_services/Makefile b/drivers/staging/vc04_services/Makefile index afe43fa5a6d7..54d9e2f31916 100644 --- a/drivers/staging/vc04_services/Makefile +++ b/drivers/staging/vc04_services/Makefile @@ -13,5 +13,5 @@ vchiq-objs := \ obj-$(CONFIG_SND_BCM2835) += bcm2835-audio/ obj-$(CONFIG_VIDEO_BCM2835) += bcm2835-camera/ -ccflags-y += -Idrivers/staging/vc04_services -D__VCCOREVER__=0x04000000 +ccflags-y += -D__VCCOREVER__=0x04000000 diff --git a/drivers/staging/vc04_services/bcm2835-audio/bcm2835-pcm.c b/drivers/staging/vc04_services/bcm2835-audio/bcm2835-pcm.c index 826016c3431a..33485184a98a 100644 --- a/drivers/staging/vc04_services/bcm2835-audio/bcm2835-pcm.c +++ b/drivers/staging/vc04_services/bcm2835-audio/bcm2835-pcm.c @@ -193,17 +193,6 @@ static int snd_bcm2835_playback_close(struct snd_pcm_substream *substream) return 0; } -static int snd_bcm2835_pcm_hw_params(struct snd_pcm_substream *substream, - struct snd_pcm_hw_params *params) -{ - return snd_pcm_lib_malloc_pages(substream, params_buffer_bytes(params)); -} - -static int snd_bcm2835_pcm_hw_free(struct snd_pcm_substream *substream) -{ - return snd_pcm_lib_free_pages(substream); -} - static int snd_bcm2835_pcm_prepare(struct snd_pcm_substream *substream) { struct bcm2835_chip *chip = snd_pcm_substream_chip(substream); @@ -316,9 +305,6 @@ snd_bcm2835_pcm_pointer(struct snd_pcm_substream *substream) static const struct snd_pcm_ops snd_bcm2835_playback_ops = { .open = snd_bcm2835_playback_open, .close = snd_bcm2835_playback_close, - .ioctl = snd_pcm_lib_ioctl, - .hw_params = snd_bcm2835_pcm_hw_params, - .hw_free = snd_bcm2835_pcm_hw_free, .prepare = snd_bcm2835_pcm_prepare, .trigger = snd_bcm2835_pcm_trigger, .pointer = snd_bcm2835_pcm_pointer, @@ -328,9 +314,6 @@ static const struct snd_pcm_ops snd_bcm2835_playback_ops = { static const struct snd_pcm_ops snd_bcm2835_playback_spdif_ops = { .open = snd_bcm2835_playback_spdif_open, .close = snd_bcm2835_playback_close, - .ioctl = snd_pcm_lib_ioctl, - .hw_params = snd_bcm2835_pcm_hw_params, - .hw_free = snd_bcm2835_pcm_hw_free, .prepare = snd_bcm2835_pcm_prepare, .trigger = snd_bcm2835_pcm_trigger, .pointer = snd_bcm2835_pcm_pointer, @@ -362,7 +345,7 @@ int snd_bcm2835_new_pcm(struct bcm2835_chip *chip, const char *name, spdif ? &snd_bcm2835_playback_spdif_ops : &snd_bcm2835_playback_ops); - snd_pcm_lib_preallocate_pages_for_all(pcm, SNDRV_DMA_TYPE_DEV, + snd_pcm_set_managed_buffer_all(pcm, SNDRV_DMA_TYPE_DEV, chip->card->dev, 128 * 1024, 128 * 1024); if (spdif) diff --git a/drivers/staging/vc04_services/bcm2835-camera/bcm2835-camera.c b/drivers/staging/vc04_services/bcm2835-camera/bcm2835-camera.c index beb6a0063bb8..1ef31a984741 100644 --- a/drivers/staging/vc04_services/bcm2835-camera/bcm2835-camera.c +++ b/drivers/staging/vc04_services/bcm2835-camera/bcm2835-camera.c @@ -60,6 +60,9 @@ MODULE_PARM_DESC(max_video_width, "Threshold for video mode"); module_param(max_video_height, int, 0644); MODULE_PARM_DESC(max_video_height, "Threshold for video mode"); +/* camera instance counter */ +static atomic_t camera_instance = ATOMIC_INIT(0); + /* global device data array */ static struct bm2835_mmal_dev *gdev[MAX_BCM2835_CAMERAS]; @@ -1870,7 +1873,6 @@ static int bcm2835_mmal_probe(struct platform_device *pdev) /* v4l2 core mutex used to protect all fops and v4l2 ioctls. */ mutex_init(&dev->mutex); - dev->camera_num = camera; dev->max_width = resolutions[camera][0]; dev->max_height = resolutions[camera][1]; @@ -1886,8 +1888,9 @@ static int bcm2835_mmal_probe(struct platform_device *pdev) dev->capture.fmt = &formats[3]; /* JPEG */ /* v4l device registration */ - snprintf(dev->v4l2_dev.name, sizeof(dev->v4l2_dev.name), - "%s", BM2835_MMAL_MODULE_NAME); + dev->camera_num = v4l2_device_set_name(&dev->v4l2_dev, + BM2835_MMAL_MODULE_NAME, + &camera_instance); ret = v4l2_device_register(NULL, &dev->v4l2_dev); if (ret) { dev_err(&pdev->dev, "%s: could not register V4L2 device: %d\n", diff --git a/drivers/staging/vc04_services/interface/vchi/vchi.h b/drivers/staging/vc04_services/interface/vchi/vchi.h index 56b1037d8e25..ff2b960d8cac 100644 --- a/drivers/staging/vc04_services/interface/vchi/vchi.h +++ b/drivers/staging/vc04_services/interface/vchi/vchi.h @@ -4,8 +4,8 @@ #ifndef VCHI_H_ #define VCHI_H_ -#include "interface/vchi/vchi_cfg.h" -#include "interface/vchi/vchi_common.h" +#include "vchi_cfg.h" +#include "vchi_common.h" /****************************************************************************** * Global defs diff --git a/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_shim.c b/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_shim.c index 0ce3b08b3441..efdd3b1c7d85 100644 --- a/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_shim.c +++ b/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_shim.c @@ -3,7 +3,7 @@ #include <linux/module.h> #include <linux/types.h> -#include "interface/vchi/vchi.h" +#include "../vchi/vchi.h" #include "vchiq.h" #include "vchiq_core.h" diff --git a/drivers/staging/vt6655/rf.c b/drivers/staging/vt6655/rf.c index fb2855e686a7..d6ca6e5551a7 100644 --- a/drivers/staging/vt6655/rf.c +++ b/drivers/staging/vt6655/rf.c @@ -758,7 +758,7 @@ bool RFvWriteWakeProgSyn(struct vnt_private *priv, unsigned char byRFType, */ bool RFbSetPower(struct vnt_private *priv, unsigned int rate, u16 uCH) { - bool ret = true; + bool ret; unsigned char byPwr = 0; unsigned char byDec = 0; diff --git a/drivers/staging/vt6656/baseband.c b/drivers/staging/vt6656/baseband.c index 4e651b698617..f18e059ce66b 100644 --- a/drivers/staging/vt6656/baseband.c +++ b/drivers/staging/vt6656/baseband.c @@ -381,8 +381,8 @@ int vnt_vt3184_init(struct vnt_private *priv) dev_dbg(&priv->usb->dev, "RF Type %d\n", priv->rf_type); - if ((priv->rf_type == RF_AL2230) || - (priv->rf_type == RF_AL2230S)) { + if (priv->rf_type == RF_AL2230 || + priv->rf_type == RF_AL2230S) { priv->bb_rx_conf = vnt_vt3184_al2230[10]; length = sizeof(vnt_vt3184_al2230); addr = vnt_vt3184_al2230; @@ -461,8 +461,8 @@ int vnt_vt3184_init(struct vnt_private *priv) if (ret) goto end; - if ((priv->rf_type == RF_VT3226) || - (priv->rf_type == RF_VT3342A0)) { + if (priv->rf_type == RF_VT3226 || + priv->rf_type == RF_VT3342A0) { ret = vnt_control_out_u8(priv, MESSAGE_REQUEST_MACREG, MAC_REG_ITRTMSET, 0x23); if (ret) diff --git a/drivers/staging/vt6656/device.h b/drivers/staging/vt6656/device.h index 50e1c8918040..fe6c11266123 100644 --- a/drivers/staging/vt6656/device.h +++ b/drivers/staging/vt6656/device.h @@ -52,6 +52,8 @@ #define RATE_AUTO 12 #define MAX_RATE 12 +#define VNT_B_RATES (BIT(RATE_1M) | BIT(RATE_2M) |\ + BIT(RATE_5M) | BIT(RATE_11M)) /* * device specific @@ -204,6 +206,22 @@ enum { CONTEXT_BEACON_PACKET }; +struct vnt_rx_header { + u32 wbk_status; + u8 rx_sts; + u8 rx_rate; + u16 pay_load_len; +} __packed; + +struct vnt_rx_tail { + __le64 tsf_time; + u8 sq; + u8 new_rsr; + u8 rssi; + u8 rsr; + u8 sq_3; +} __packed; + /* RCB (Receive Control Block) */ struct vnt_rcb { void *priv; @@ -262,7 +280,6 @@ struct vnt_private { struct usb_interface *intf; u64 tsf_time; - u8 rx_rate; u32 rx_buf_sz; int mc_list_count; diff --git a/drivers/staging/vt6656/dpc.c b/drivers/staging/vt6656/dpc.c index 3b94e80f1d5e..821aae8ca402 100644 --- a/drivers/staging/vt6656/dpc.c +++ b/drivers/staging/vt6656/dpc.c @@ -29,27 +29,21 @@ int vnt_rx_data(struct vnt_private *priv, struct vnt_rcb *ptr_rcb, struct ieee80211_hw *hw = priv->hw; struct ieee80211_supported_band *sband; struct sk_buff *skb; - struct ieee80211_rx_status rx_status = { 0 }; - struct ieee80211_hdr *hdr; - __le16 fc; - u8 *rsr, *new_rsr, *rssi; - __le64 *tsf_time; + struct ieee80211_rx_status *rx_status; + struct vnt_rx_header *head; + struct vnt_rx_tail *tail; u32 frame_size; - int ii, r; - u8 *rx_rate, *sq, *sq_3; - u32 wbk_status; - u8 *skb_data; - u16 *pay_load_len; - u16 pay_load_with_padding; + int ii; + u16 rx_bitrate, pay_load_with_padding; u8 rate_idx = 0; - u8 rate[MAX_RATE] = {2, 4, 11, 22, 12, 18, 24, 36, 48, 72, 96, 108}; long rx_dbm; skb = ptr_rcb->skb; + rx_status = IEEE80211_SKB_RXCB(skb); /* [31:16]RcvByteCount ( not include 4-byte Status ) */ - wbk_status = *((u32 *)(skb->data)); - frame_size = wbk_status >> 16; + head = (struct vnt_rx_header *)skb->data; + frame_size = head->wbk_status >> 16; frame_size += 4; if (bytes_received != frame_size) { @@ -63,106 +57,66 @@ int vnt_rx_data(struct vnt_private *priv, struct vnt_rcb *ptr_rcb, return false; } - skb_data = (u8 *)skb->data; - - rx_rate = skb_data + 5; - /* real Frame Size = USBframe_size -4WbkStatus - 4RxStatus */ /* -8TSF - 4RSR - 4SQ3 - ?Padding */ /* if SQ3 the range is 24~27, if no SQ3 the range is 20~23 */ - pay_load_len = (u16 *)(skb_data + 6); - /*Fix hardware bug => PLCP_Length error */ - if (((bytes_received - (*pay_load_len)) > 27) || - ((bytes_received - (*pay_load_len)) < 24) || - (bytes_received < (*pay_load_len))) { + if (((bytes_received - head->pay_load_len) > 27) || + ((bytes_received - head->pay_load_len) < 24) || + (bytes_received < head->pay_load_len)) { dev_dbg(&priv->usb->dev, "Wrong PLCP Length %x\n", - *pay_load_len); + head->pay_load_len); return false; } sband = hw->wiphy->bands[hw->conf.chandef.chan->band]; - - for (r = RATE_1M; r < MAX_RATE; r++) { - if (*rx_rate == rate[r]) - break; - } - - priv->rx_rate = r; + rx_bitrate = head->rx_rate * 5; /* rx_rate * 5 */ for (ii = 0; ii < sband->n_bitrates; ii++) { - if (sband->bitrates[ii].hw_value == r) { + if (sband->bitrates[ii].bitrate == rx_bitrate) { rate_idx = ii; break; } } if (ii == sband->n_bitrates) { - dev_dbg(&priv->usb->dev, "Wrong RxRate %x\n", *rx_rate); + dev_dbg(&priv->usb->dev, "Wrong Rx Bit Rate %d\n", rx_bitrate); return false; } - pay_load_with_padding = ((*pay_load_len / 4) + - ((*pay_load_len % 4) ? 1 : 0)) * 4; - - tsf_time = (__le64 *)(skb_data + 8 + pay_load_with_padding); - - priv->tsf_time = le64_to_cpu(*tsf_time); + pay_load_with_padding = ((head->pay_load_len / 4) + + ((head->pay_load_len % 4) ? 1 : 0)) * 4; - if (priv->bb_type == BB_TYPE_11G) { - sq_3 = skb_data + 8 + pay_load_with_padding + 12; - sq = sq_3; - } else { - sq = skb_data + 8 + pay_load_with_padding + 8; - sq_3 = sq; - } - - new_rsr = skb_data + 8 + pay_load_with_padding + 9; - rssi = skb_data + 8 + pay_load_with_padding + 10; + tail = (struct vnt_rx_tail *)(skb->data + + sizeof(*head) + pay_load_with_padding); + priv->tsf_time = le64_to_cpu(tail->tsf_time); - rsr = skb_data + 8 + pay_load_with_padding + 11; - if (*rsr & (RSR_IVLDTYP | RSR_IVLDLEN)) + if (tail->rsr & (RSR_IVLDTYP | RSR_IVLDLEN)) return false; - frame_size = *pay_load_len; - - vnt_rf_rssi_to_dbm(priv, *rssi, &rx_dbm); + vnt_rf_rssi_to_dbm(priv, tail->rssi, &rx_dbm); priv->bb_pre_ed_rssi = (u8)rx_dbm + 1; priv->current_rssi = priv->bb_pre_ed_rssi; - skb_pull(skb, 8); - skb_trim(skb, frame_size); - - rx_status.mactime = priv->tsf_time; - rx_status.band = hw->conf.chandef.chan->band; - rx_status.signal = rx_dbm; - rx_status.flag = 0; - rx_status.freq = hw->conf.chandef.chan->center_freq; + skb_pull(skb, sizeof(*head)); + skb_trim(skb, head->pay_load_len); - if (!(*rsr & RSR_CRCOK)) - rx_status.flag |= RX_FLAG_FAILED_FCS_CRC; + rx_status->mactime = priv->tsf_time; + rx_status->band = hw->conf.chandef.chan->band; + rx_status->signal = rx_dbm; + rx_status->flag = 0; + rx_status->freq = hw->conf.chandef.chan->center_freq; - hdr = (struct ieee80211_hdr *)(skb->data); - fc = hdr->frame_control; + if (!(tail->rsr & RSR_CRCOK)) + rx_status->flag |= RX_FLAG_FAILED_FCS_CRC; - rx_status.rate_idx = rate_idx; - - if (ieee80211_has_protected(fc)) { - if (priv->local_id > REV_ID_VT3253_A1) { - rx_status.flag |= RX_FLAG_DECRYPTED; - - /* Drop packet */ - if (!(*new_rsr & NEWRSR_DECRYPTOK)) { - dev_kfree_skb(skb); - return true; - } - } - } + rx_status->rate_idx = rate_idx; - memcpy(IEEE80211_SKB_RXCB(skb), &rx_status, sizeof(rx_status)); + if (tail->new_rsr & NEWRSR_DECRYPTOK) + rx_status->flag |= RX_FLAG_DECRYPTED; ieee80211_rx_irqsafe(priv->hw, skb); diff --git a/drivers/staging/vt6656/firmware.c b/drivers/staging/vt6656/firmware.c index 60a00af250bf..70358d427211 100644 --- a/drivers/staging/vt6656/firmware.c +++ b/drivers/staging/vt6656/firmware.c @@ -30,7 +30,6 @@ int vnt_download_firmware(struct vnt_private *priv) { struct device *dev = &priv->usb->dev; const struct firmware *fw; - void *buffer = NULL; u16 length; int ii; int ret = 0; @@ -44,26 +43,17 @@ int vnt_download_firmware(struct vnt_private *priv) goto end; } - buffer = kmalloc(FIRMWARE_CHUNK_SIZE, GFP_KERNEL); - if (!buffer) { - ret = -ENOMEM; - goto free_fw; - } - for (ii = 0; ii < fw->size; ii += FIRMWARE_CHUNK_SIZE) { length = min_t(int, fw->size - ii, FIRMWARE_CHUNK_SIZE); - memcpy(buffer, fw->data + ii, length); ret = vnt_control_out(priv, 0, 0x1200 + ii, 0x0000, length, - buffer); + fw->data + ii); if (ret) - goto free_buffer; + goto free_fw; dev_dbg(dev, "Download firmware...%d %zu\n", ii, fw->size); } -free_buffer: - kfree(buffer); free_fw: release_firmware(fw); end: diff --git a/drivers/staging/vt6656/int.c b/drivers/staging/vt6656/int.c index f40947955675..af215860be4c 100644 --- a/drivers/staging/vt6656/int.c +++ b/drivers/staging/vt6656/int.c @@ -99,9 +99,11 @@ static int vnt_int_report_rate(struct vnt_private *priv, u8 pkt_no, u8 tsr) info->status.rates[0].count = tx_retry; - if (!(tsr & (TSR_TMO | TSR_RETRYTMO))) { + if (!(tsr & TSR_TMO)) { info->status.rates[0].idx = idx; - info->flags |= IEEE80211_TX_STAT_ACK; + + if (!(info->flags & IEEE80211_TX_CTL_NO_ACK)) + info->flags |= IEEE80211_TX_STAT_ACK; } ieee80211_tx_status_irqsafe(priv->hw, context->skb); diff --git a/drivers/staging/vt6656/main_usb.c b/drivers/staging/vt6656/main_usb.c index 9cb924c54571..5e48b3ddb94c 100644 --- a/drivers/staging/vt6656/main_usb.c +++ b/drivers/staging/vt6656/main_usb.c @@ -1015,6 +1015,7 @@ vt6656_probe(struct usb_interface *intf, const struct usb_device_id *id) ieee80211_hw_set(priv->hw, RX_INCLUDES_FCS); ieee80211_hw_set(priv->hw, REPORTS_TX_ACK_STATUS); ieee80211_hw_set(priv->hw, SUPPORTS_PS); + ieee80211_hw_set(priv->hw, PS_NULLFUNC_STACK); priv->hw->max_signal = 100; diff --git a/drivers/staging/vt6656/rxtx.c b/drivers/staging/vt6656/rxtx.c index f9020a4f7bbf..29caba728906 100644 --- a/drivers/staging/vt6656/rxtx.c +++ b/drivers/staging/vt6656/rxtx.c @@ -278,11 +278,9 @@ static u16 vnt_rxtx_datahead_g(struct vnt_usb_send_context *tx_context, PK_TYPE_11B, &buf->b); /* Get Duration and TimeStamp */ - if (ieee80211_is_pspoll(hdr->frame_control)) { - __le16 dur = cpu_to_le16(priv->current_aid | BIT(14) | BIT(15)); - - buf->duration_a = dur; - buf->duration_b = dur; + if (ieee80211_is_nullfunc(hdr->frame_control)) { + buf->duration_a = hdr->duration_id; + buf->duration_b = hdr->duration_id; } else { buf->duration_a = vnt_get_duration_le(priv, tx_context->pkt_type, need_ack); @@ -371,10 +369,8 @@ static u16 vnt_rxtx_datahead_ab(struct vnt_usb_send_context *tx_context, tx_context->pkt_type, &buf->ab); /* Get Duration and TimeStampOff */ - if (ieee80211_is_pspoll(hdr->frame_control)) { - __le16 dur = cpu_to_le16(priv->current_aid | BIT(14) | BIT(15)); - - buf->duration = dur; + if (ieee80211_is_nullfunc(hdr->frame_control)) { + buf->duration = hdr->duration_id; } else { buf->duration = vnt_get_duration_le(priv, tx_context->pkt_type, need_ack); @@ -815,10 +811,14 @@ int vnt_tx_packet(struct vnt_private *priv, struct sk_buff *skb) if (info->band == NL80211_BAND_5GHZ) { pkt_type = PK_TYPE_11A; } else { - if (tx_rate->flags & IEEE80211_TX_RC_USE_CTS_PROTECT) - pkt_type = PK_TYPE_11GB; - else - pkt_type = PK_TYPE_11GA; + if (tx_rate->flags & IEEE80211_TX_RC_USE_CTS_PROTECT) { + if (priv->basic_rates & VNT_B_RATES) + pkt_type = PK_TYPE_11GB; + else + pkt_type = PK_TYPE_11GA; + } else { + pkt_type = PK_TYPE_11A; + } } } else { pkt_type = PK_TYPE_11B; diff --git a/drivers/staging/vt6656/usbpipe.c b/drivers/staging/vt6656/usbpipe.c index d977d4777e4f..7bfccc48a366 100644 --- a/drivers/staging/vt6656/usbpipe.c +++ b/drivers/staging/vt6656/usbpipe.c @@ -34,7 +34,7 @@ #define USB_CTL_WAIT 500 /* ms */ int vnt_control_out(struct vnt_private *priv, u8 request, u16 value, - u16 index, u16 length, u8 *buffer) + u16 index, u16 length, const u8 *buffer) { int ret = 0; u8 *usb_buffer; diff --git a/drivers/staging/vt6656/usbpipe.h b/drivers/staging/vt6656/usbpipe.h index b65d9c01a211..4e3341bc3221 100644 --- a/drivers/staging/vt6656/usbpipe.h +++ b/drivers/staging/vt6656/usbpipe.h @@ -21,7 +21,7 @@ #define VNT_REG_BLOCK_SIZE 64 int vnt_control_out(struct vnt_private *priv, u8 request, u16 value, - u16 index, u16 length, u8 *buffer); + u16 index, u16 length, const u8 *buffer); int vnt_control_in(struct vnt_private *priv, u8 request, u16 value, u16 index, u16 length, u8 *buffer); diff --git a/drivers/staging/wfx/TODO b/drivers/staging/wfx/TODO index e44772289af8..efcb7c6a5aa7 100644 --- a/drivers/staging/wfx/TODO +++ b/drivers/staging/wfx/TODO @@ -1,17 +1,60 @@ This is a list of things that need to be done to get this driver out of the staging directory. - - I have to take a decision about secure link support. I can: - - drop completely - - keep it in an external patch (my preferred option) - - replace call to mbedtls with kernel crypto API (necessitate a - bunch of work) - - pull mbedtls in kernel (non-realistic) - - - mac80211 interface does not (yet) have expected quality to be placed - outside of staging: - - Some processings are redundant with mac80211 ones - - Many members from wfx_dev/wfx_vif can be retrieved from mac80211 - structures - - Some functions are too complex - - ... + - All structures defined in hif_api_*.h are intended to sent/received to/from + hardware. All their members whould be declared __le32 or __le16. + See: + https://lore.kernel.org/lkml/20191111202852.GX26530@ZenIV.linux.org.uk + + - Once previous item done, it will be possible to audit the driver with + `sparse'. It will probably find tons of problems with big endian + architectures. + + - hif_api_*.h whave been imported from firmware code. Some of the structures + are never used in driver. + + - Driver try to maintains power save status of the stations. However, this + work is already done by mac80211. sta_asleep_mask and pspoll_mask should be + dropped. + + - wfx_tx_queues_get() should be reworked. It currently try compute itself the + QoS policy. However, firmware already do the job. Firmware would prefer to + have a few packets in each queue and be able to choose itself which queue to + use. + + - As suggested by Felix, rate control could be improved following this idea: + https://lore.kernel.org/lkml/3099559.gv3Q75KnN1@pc-42/ + + - When driver is about to loose BSS, it forge its own Null Func request (see + wfx_cqm_bssloss_sm()). It should use mechanism provided by mac80211. + + - AP is actually is setup after a call to wfx_bss_info_changed(). Yet, + ieee80211_ops provide callback start_ap(). + + - The current process for joining a network is incredibly complex. Should be + reworked. + + - Monitoring mode is not implemented despite being mandatory by mac80211. + + - "compatible" value are not correct. They should be "vendor,chip". See: + https://lore.kernel.org/driverdev-devel/5226570.CMH5hVlZcI@pc-42 + + - The "state" field from wfx_vif should be replaced by "vif->type". + + - It seems that wfx_upload_keys() is useless. + + - "event_queue" from wfx_vif seems overkill. These event are rare and they + probably could be handled in a simpler fashion. + + - Feature called "secure link" should be either developed (using kernel + crypto API) or dropped. + + - In wfx_cmd_send(), "async" allow to send command without waiting the reply. + It may help in some situation, but it is not yet used. In add, it may cause + some trouble: + https://lore.kernel.org/driverdev-devel/alpine.DEB.2.21.1910041317381.2992@hadrien/ + So, fix it (by replacing the mutex with a semaphore) or drop it. + + - Chip support P2P, but driver does not implement it. + + - Chip support kind of Mesh, but driver does not implement it. diff --git a/drivers/staging/wfx/bh.c b/drivers/staging/wfx/bh.c index 2432ba95c2f5..983c41d1fe7c 100644 --- a/drivers/staging/wfx/bh.c +++ b/drivers/staging/wfx/bh.c @@ -271,8 +271,7 @@ static void bh_work(struct work_struct *work) if (last_op_is_rx) ack_sdio_data(wdev); - if (!wdev->hif.tx_buffers_used && !work_pending(work) && - !atomic_read(&wdev->scan_in_progress)) { + if (!wdev->hif.tx_buffers_used && !work_pending(work)) { device_release(wdev); release_chip = true; } diff --git a/drivers/staging/wfx/bus_spi.c b/drivers/staging/wfx/bus_spi.c index ab0cda1e124f..40bc33035de2 100644 --- a/drivers/staging/wfx/bus_spi.c +++ b/drivers/staging/wfx/bus_spi.c @@ -107,6 +107,8 @@ static int wfx_spi_copy_to_io(void *priv, unsigned int addr, cpu_to_le16s(®addr); + // Register address and CONFIG content always use 16bit big endian + // ("BADC" order) if (bus->need_swab) swab16s(®addr); if (bus->need_swab && addr == WFX_REG_CONFIG) @@ -183,7 +185,7 @@ static int wfx_spi_probe(struct spi_device *func) if (func->bits_per_word != 16 && func->bits_per_word != 8) dev_warn(&func->dev, "unusual bits/word value: %d\n", func->bits_per_word); - if (func->max_speed_hz > 49000000) + if (func->max_speed_hz > 50000000) dev_warn(&func->dev, "%dHz is a very high speed\n", func->max_speed_hz); @@ -223,8 +225,7 @@ static int wfx_spi_probe(struct spi_device *func) return ret; } -/* Disconnect Function to be called by SPI stack when device is disconnected */ -static int wfx_spi_disconnect(struct spi_device *func) +static int wfx_spi_remove(struct spi_device *func) { struct wfx_spi_priv *bus = spi_get_drvdata(func); @@ -263,5 +264,5 @@ struct spi_driver wfx_spi_driver = { }, .id_table = wfx_spi_id, .probe = wfx_spi_probe, - .remove = wfx_spi_disconnect, + .remove = wfx_spi_remove, }; diff --git a/drivers/staging/wfx/data_rx.c b/drivers/staging/wfx/data_rx.c index e7fcce8d0cc4..5d198457c6ce 100644 --- a/drivers/staging/wfx/data_rx.c +++ b/drivers/staging/wfx/data_rx.c @@ -13,42 +13,9 @@ #include "bh.h" #include "sta.h" -static int wfx_handle_pspoll(struct wfx_vif *wvif, struct sk_buff *skb) -{ - struct ieee80211_sta *sta; - struct ieee80211_pspoll *pspoll = (struct ieee80211_pspoll *)skb->data; - int link_id = 0; - u32 pspoll_mask = 0; - int i; - - if (wvif->state != WFX_STATE_AP) - return 1; - if (!ether_addr_equal(wvif->vif->addr, pspoll->bssid)) - return 1; - - rcu_read_lock(); - sta = ieee80211_find_sta(wvif->vif, pspoll->ta); - if (sta) - link_id = ((struct wfx_sta_priv *)&sta->drv_priv)->link_id; - rcu_read_unlock(); - if (link_id) - pspoll_mask = BIT(link_id); - else - return 1; - - wvif->pspoll_mask |= pspoll_mask; - /* Do not report pspols if data for given link id is queued already. */ - for (i = 0; i < IEEE80211_NUM_ACS; ++i) { - if (wfx_tx_queue_get_num_queued(&wvif->wdev->tx_queue[i], - pspoll_mask)) { - wfx_bh_request_tx(wvif->wdev); - return 1; - } - } - return 0; -} - -static int wfx_drop_encrypt_data(struct wfx_dev *wdev, struct hif_ind_rx *arg, struct sk_buff *skb) +static int wfx_drop_encrypt_data(struct wfx_dev *wdev, + const struct hif_ind_rx *arg, + struct sk_buff *skb) { struct ieee80211_hdr *frame = (struct ieee80211_hdr *) skb->data; size_t hdrlen = ieee80211_hdrlen(frame->frame_control); @@ -98,15 +65,12 @@ static int wfx_drop_encrypt_data(struct wfx_dev *wdev, struct hif_ind_rx *arg, s } -void wfx_rx_cb(struct wfx_vif *wvif, struct hif_ind_rx *arg, - struct sk_buff *skb) +void wfx_rx_cb(struct wfx_vif *wvif, + const struct hif_ind_rx *arg, struct sk_buff *skb) { - int link_id = arg->rx_flags.peer_sta_id; struct ieee80211_rx_status *hdr = IEEE80211_SKB_RXCB(skb); struct ieee80211_hdr *frame = (struct ieee80211_hdr *)skb->data; struct ieee80211_mgmt *mgmt = (struct ieee80211_mgmt *)skb->data; - struct wfx_link_entry *entry = NULL; - bool early_data = false; memset(hdr, 0, sizeof(*hdr)); @@ -116,14 +80,6 @@ void wfx_rx_cb(struct wfx_vif *wvif, struct hif_ind_rx *arg, ieee80211_is_beacon(frame->frame_control))) goto drop; - if (link_id && link_id <= WFX_MAX_STA_IN_AP_MODE) { - entry = &wvif->link_id_db[link_id - 1]; - entry->timestamp = jiffies; - if (entry->status == WFX_LINK_SOFT && - ieee80211_is_data(frame->frame_control)) - early_data = true; - } - if (arg->status == HIF_STATUS_MICFAILURE) hdr->flag |= RX_FLAG_MMIC_ERROR; else if (arg->status) @@ -134,10 +90,6 @@ void wfx_rx_cb(struct wfx_vif *wvif, struct hif_ind_rx *arg, goto drop; } - if (ieee80211_is_pspoll(frame->frame_control)) - if (wfx_handle_pspoll(wvif, skb)) - goto drop; - hdr->band = NL80211_BAND_2GHZ; hdr->freq = ieee80211_channel_to_frequency(arg->channel_number, hdr->band); @@ -171,20 +123,6 @@ void wfx_rx_cb(struct wfx_vif *wvif, struct hif_ind_rx *arg, !arg->status && wvif->vif && ether_addr_equal(ieee80211_get_SA(frame), wvif->vif->bss_conf.bssid)) { - const u8 *tim_ie; - u8 *ies = mgmt->u.beacon.variable; - size_t ies_len = skb->len - (ies - skb->data); - - tim_ie = cfg80211_find_ie(WLAN_EID_TIM, ies, ies_len); - if (tim_ie) { - struct ieee80211_tim_ie *tim = (struct ieee80211_tim_ie *)&tim_ie[2]; - - if (wvif->dtim_period != tim->dtim_period) { - wvif->dtim_period = tim->dtim_period; - schedule_work(&wvif->set_beacon_wakeup_period_work); - } - } - /* Disable beacon filter once we're associated... */ if (wvif->disable_beacon_filter && (wvif->vif->bss_conf.assoc || @@ -193,18 +131,7 @@ void wfx_rx_cb(struct wfx_vif *wvif, struct hif_ind_rx *arg, schedule_work(&wvif->update_filtering_work); } } - - if (early_data) { - spin_lock_bh(&wvif->ps_state_lock); - /* Double-check status with lock held */ - if (entry->status == WFX_LINK_SOFT) - skb_queue_tail(&entry->rx_queue, skb); - else - ieee80211_rx_irqsafe(wvif->wdev->hw, skb); - spin_unlock_bh(&wvif->ps_state_lock); - } else { - ieee80211_rx_irqsafe(wvif->wdev->hw, skb); - } + ieee80211_rx_irqsafe(wvif->wdev->hw, skb); return; diff --git a/drivers/staging/wfx/data_rx.h b/drivers/staging/wfx/data_rx.h index a50ce352bc5e..61c28bfd2a37 100644 --- a/drivers/staging/wfx/data_rx.h +++ b/drivers/staging/wfx/data_rx.h @@ -13,7 +13,7 @@ struct wfx_vif; struct sk_buff; -void wfx_rx_cb(struct wfx_vif *wvif, struct hif_ind_rx *arg, - struct sk_buff *skb); +void wfx_rx_cb(struct wfx_vif *wvif, + const struct hif_ind_rx *arg, struct sk_buff *skb); #endif /* WFX_DATA_RX_H */ diff --git a/drivers/staging/wfx/data_tx.c b/drivers/staging/wfx/data_tx.c index b13d7341f8bb..20f4740734f2 100644 --- a/drivers/staging/wfx/data_tx.c +++ b/drivers/staging/wfx/data_tx.c @@ -17,7 +17,6 @@ #include "hif_tx_mib.h" #define WFX_INVALID_RATE_ID 15 -#define WFX_LINK_ID_NO_ASSOC 15 #define WFX_LINK_ID_GC_TIMEOUT ((unsigned long)(10 * HZ)) static int wfx_get_hw_rate(struct wfx_dev *wdev, @@ -169,7 +168,8 @@ static int wfx_tx_policy_get(struct wfx_vif *wvif, wfx_tx_policy_build(wvif, &wanted, rates); spin_lock_bh(&cache->lock); - if (WARN_ON(list_empty(&cache->free))) { + if (list_empty(&cache->free)) { + WARN(1, "unable to get a valid Tx policy"); spin_unlock_bh(&cache->lock); return WFX_INVALID_RATE_ID; } @@ -216,38 +216,25 @@ static void wfx_tx_policy_put(struct wfx_vif *wvif, int idx) static int wfx_tx_policy_upload(struct wfx_vif *wvif) { + struct tx_policy *policies = wvif->tx_policy_cache.cache; + u8 tmp_rates[12]; int i; - struct tx_policy_cache *cache = &wvif->tx_policy_cache; - struct hif_mib_set_tx_rate_retry_policy *arg = - kzalloc(struct_size(arg, - tx_rate_retry_policy, - HIF_MIB_NUM_TX_RATE_RETRY_POLICIES), - GFP_KERNEL); - struct hif_mib_tx_rate_retry_policy *dst; - spin_lock_bh(&cache->lock); - /* Upload only modified entries. */ - for (i = 0; i < HIF_MIB_NUM_TX_RATE_RETRY_POLICIES; ++i) { - struct tx_policy *src = &cache->cache[i]; - - if (!src->uploaded && memzcmp(src->rates, sizeof(src->rates))) { - dst = arg->tx_rate_retry_policy + - arg->num_tx_rate_policies; - - dst->policy_index = i; - dst->short_retry_count = 255; - dst->long_retry_count = 255; - dst->first_rate_sel = 1; - dst->terminate = 1; - dst->count_init = 1; - memcpy(&dst->rates, src->rates, sizeof(src->rates)); - src->uploaded = true; - arg->num_tx_rate_policies++; + do { + spin_lock_bh(&wvif->tx_policy_cache.lock); + for (i = 0; i < HIF_MIB_NUM_TX_RATE_RETRY_POLICIES; ++i) + if (!policies[i].uploaded && + memzcmp(policies[i].rates, sizeof(policies[i].rates))) + break; + if (i < HIF_MIB_NUM_TX_RATE_RETRY_POLICIES) { + policies[i].uploaded = 1; + memcpy(tmp_rates, policies[i].rates, sizeof(tmp_rates)); + spin_unlock_bh(&wvif->tx_policy_cache.lock); + hif_set_tx_rate_retry_policy(wvif, i, tmp_rates); + } else { + spin_unlock_bh(&wvif->tx_policy_cache.lock); } - } - spin_unlock_bh(&cache->lock); - hif_set_tx_rate_retry_policy(wvif, arg); - kfree(arg); + } while (i < HIF_MIB_NUM_TX_RATE_RETRY_POLICIES); return 0; } @@ -277,164 +264,6 @@ void wfx_tx_policy_init(struct wfx_vif *wvif) list_add(&cache->cache[i].link, &cache->free); } -/* Link ID related functions */ - -static int wfx_alloc_link_id(struct wfx_vif *wvif, const u8 *mac) -{ - int i, ret = 0; - unsigned long max_inactivity = 0; - unsigned long now = jiffies; - - spin_lock_bh(&wvif->ps_state_lock); - for (i = 0; i < WFX_MAX_STA_IN_AP_MODE; ++i) { - if (!wvif->link_id_db[i].status) { - ret = i + 1; - break; - } else if (wvif->link_id_db[i].status != WFX_LINK_HARD && - !wvif->wdev->tx_queue_stats.link_map_cache[i + 1]) { - unsigned long inactivity = - now - wvif->link_id_db[i].timestamp; - - if (inactivity < max_inactivity) - continue; - max_inactivity = inactivity; - ret = i + 1; - } - } - - if (ret) { - struct wfx_link_entry *entry = &wvif->link_id_db[ret - 1]; - - entry->status = WFX_LINK_RESERVE; - ether_addr_copy(entry->mac, mac); - memset(&entry->buffered, 0, WFX_MAX_TID); - skb_queue_head_init(&entry->rx_queue); - wfx_tx_lock(wvif->wdev); - - if (!schedule_work(&wvif->link_id_work)) - wfx_tx_unlock(wvif->wdev); - } else { - dev_info(wvif->wdev->dev, "no more link-id available\n"); - } - spin_unlock_bh(&wvif->ps_state_lock); - return ret; -} - -int wfx_find_link_id(struct wfx_vif *wvif, const u8 *mac) -{ - int i, ret = 0; - - spin_lock_bh(&wvif->ps_state_lock); - for (i = 0; i < WFX_MAX_STA_IN_AP_MODE; ++i) { - if (ether_addr_equal(mac, wvif->link_id_db[i].mac) && - wvif->link_id_db[i].status) { - wvif->link_id_db[i].timestamp = jiffies; - ret = i + 1; - break; - } - } - spin_unlock_bh(&wvif->ps_state_lock); - return ret; -} - -static int wfx_map_link(struct wfx_vif *wvif, - struct wfx_link_entry *link_entry, int sta_id) -{ - int ret; - - ret = hif_map_link(wvif, link_entry->mac, 0, sta_id); - - if (ret == 0) - /* Save the MAC address currently associated with the peer - * for future unmap request - */ - ether_addr_copy(link_entry->old_mac, link_entry->mac); - - return ret; -} - -int wfx_unmap_link(struct wfx_vif *wvif, int sta_id) -{ - u8 *mac_addr = NULL; - - if (sta_id) - mac_addr = wvif->link_id_db[sta_id - 1].old_mac; - - return hif_map_link(wvif, mac_addr, 1, sta_id); -} - -void wfx_link_id_gc_work(struct work_struct *work) -{ - struct wfx_vif *wvif = - container_of(work, struct wfx_vif, link_id_gc_work.work); - unsigned long now = jiffies; - unsigned long next_gc = -1; - long ttl; - u32 mask; - int i; - - if (wvif->state != WFX_STATE_AP) - return; - - wfx_tx_lock_flush(wvif->wdev); - spin_lock_bh(&wvif->ps_state_lock); - for (i = 0; i < WFX_MAX_STA_IN_AP_MODE; ++i) { - bool need_reset = false; - - mask = BIT(i + 1); - if (wvif->link_id_db[i].status == WFX_LINK_RESERVE || - (wvif->link_id_db[i].status == WFX_LINK_HARD && - !(wvif->link_id_map & mask))) { - if (wvif->link_id_map & mask) { - wvif->sta_asleep_mask &= ~mask; - wvif->pspoll_mask &= ~mask; - need_reset = true; - } - wvif->link_id_map |= mask; - if (wvif->link_id_db[i].status != WFX_LINK_HARD) - wvif->link_id_db[i].status = WFX_LINK_SOFT; - - spin_unlock_bh(&wvif->ps_state_lock); - if (need_reset) - wfx_unmap_link(wvif, i + 1); - wfx_map_link(wvif, &wvif->link_id_db[i], i + 1); - next_gc = min(next_gc, WFX_LINK_ID_GC_TIMEOUT); - spin_lock_bh(&wvif->ps_state_lock); - } else if (wvif->link_id_db[i].status == WFX_LINK_SOFT) { - ttl = wvif->link_id_db[i].timestamp - now + - WFX_LINK_ID_GC_TIMEOUT; - if (ttl <= 0) { - need_reset = true; - wvif->link_id_db[i].status = WFX_LINK_OFF; - wvif->link_id_map &= ~mask; - wvif->sta_asleep_mask &= ~mask; - wvif->pspoll_mask &= ~mask; - spin_unlock_bh(&wvif->ps_state_lock); - wfx_unmap_link(wvif, i + 1); - spin_lock_bh(&wvif->ps_state_lock); - } else { - next_gc = min_t(unsigned long, next_gc, ttl); - } - } - if (need_reset) - skb_queue_purge(&wvif->link_id_db[i].rx_queue); - } - spin_unlock_bh(&wvif->ps_state_lock); - if (next_gc != -1) - schedule_delayed_work(&wvif->link_id_gc_work, next_gc); - wfx_tx_unlock(wvif->wdev); -} - -void wfx_link_id_work(struct work_struct *work) -{ - struct wfx_vif *wvif = - container_of(work, struct wfx_vif, link_id_work); - - wfx_tx_flush(wvif->wdev); - wfx_link_id_gc_work(&wvif->link_id_gc_work.work); - wfx_tx_unlock(wvif->wdev); -} - /* Tx implementation */ static bool ieee80211_is_action_back(struct ieee80211_hdr *hdr) @@ -453,29 +282,21 @@ static void wfx_tx_manage_pm(struct wfx_vif *wvif, struct ieee80211_hdr *hdr, struct ieee80211_sta *sta) { u32 mask = ~BIT(tx_priv->raw_link_id); + struct wfx_sta_priv *sta_priv; + int tid = ieee80211_get_tid(hdr); spin_lock_bh(&wvif->ps_state_lock); - if (ieee80211_is_auth(hdr->frame_control)) { + if (ieee80211_is_auth(hdr->frame_control)) wvif->sta_asleep_mask &= mask; - wvif->pspoll_mask &= mask; - } - - if (tx_priv->link_id == WFX_LINK_ID_AFTER_DTIM && - !wvif->mcast_buffered) { - wvif->mcast_buffered = true; - if (wvif->sta_asleep_mask) - schedule_work(&wvif->mcast_start_work); - } - - if (tx_priv->raw_link_id) { - wvif->link_id_db[tx_priv->raw_link_id - 1].timestamp = jiffies; - if (tx_priv->tid < WFX_MAX_TID) - wvif->link_id_db[tx_priv->raw_link_id - 1].buffered[tx_priv->tid]++; - } spin_unlock_bh(&wvif->ps_state_lock); - if (sta) - ieee80211_sta_set_buffered(sta, tx_priv->tid, true); + if (sta) { + sta_priv = (struct wfx_sta_priv *)&sta->drv_priv; + spin_lock_bh(&sta_priv->lock); + sta_priv->buffered[tid]++; + ieee80211_sta_set_buffered(sta, tid, true); + spin_unlock_bh(&sta_priv->lock); + } } static u8 wfx_tx_get_raw_link_id(struct wfx_vif *wvif, @@ -485,7 +306,6 @@ static u8 wfx_tx_get_raw_link_id(struct wfx_vif *wvif, struct wfx_sta_priv *sta_priv = sta ? (struct wfx_sta_priv *) &sta->drv_priv : NULL; const u8 *da = ieee80211_get_DA(hdr); - int ret; if (sta_priv && sta_priv->link_id) return sta_priv->link_id; @@ -493,14 +313,7 @@ static u8 wfx_tx_get_raw_link_id(struct wfx_vif *wvif, return 0; if (is_multicast_ether_addr(da)) return 0; - ret = wfx_find_link_id(wvif, da); - if (!ret) - ret = wfx_alloc_link_id(wvif, da); - if (!ret) { - dev_err(wvif->wdev->dev, "no more link-id available\n"); - return WFX_LINK_ID_NO_ASSOC; - } - return ret; + return WFX_LINK_ID_NO_ASSOC; } static void wfx_tx_fixup_rates(struct ieee80211_tx_rate *rates) @@ -597,17 +410,6 @@ static struct hif_ht_tx_parameters wfx_tx_get_tx_parms(struct wfx_dev *wdev, str return ret; } -static u8 wfx_tx_get_tid(struct ieee80211_hdr *hdr) -{ - // FIXME: ieee80211_get_tid(hdr) should be sufficient for all cases. - if (!ieee80211_is_data(hdr->frame_control)) - return WFX_MAX_TID; - if (ieee80211_is_data_qos(hdr->frame_control)) - return ieee80211_get_tid(hdr); - else - return 0; -} - static int wfx_tx_get_icv_len(struct ieee80211_key_conf *hw_key) { int mic_space; @@ -639,7 +441,6 @@ static int wfx_tx_inner(struct wfx_vif *wvif, struct ieee80211_sta *sta, memset(tx_info->rate_driver_data, 0, sizeof(struct wfx_tx_priv)); // Fill tx_priv tx_priv = (struct wfx_tx_priv *)tx_info->rate_driver_data; - tx_priv->tid = wfx_tx_get_tid(hdr); tx_priv->raw_link_id = wfx_tx_get_raw_link_id(wvif, sta, hdr); tx_priv->link_id = tx_priv->raw_link_id; if (ieee80211_has_protected(hdr->frame_control)) @@ -668,9 +469,15 @@ static int wfx_tx_inner(struct wfx_vif *wvif, struct ieee80211_sta *sta, // Fill tx request req = (struct hif_req_tx *)hif_msg->body; - req->packet_id = queue_id << 16 | - IEEE80211_SEQ_TO_SN(le16_to_cpu(hdr->seq_ctrl)); + // packet_id just need to be unique on device. 32bits are more than + // necessary for that task, so we tae advantage of it to add some extra + // data for debug. + req->packet_id = queue_id << 28 | + IEEE80211_SEQ_TO_SN(le16_to_cpu(hdr->seq_ctrl)) << 16 | + (atomic_add_return(1, &wvif->wdev->packet_id) & 0xFFFF); req->data_flags.fc_offset = offset; + if (tx_info->flags & IEEE80211_TX_CTL_SEND_AFTER_DTIM) + req->data_flags.after_dtim = 1; req->queue_id.peer_sta_id = tx_priv->raw_link_id; // Queue index are inverted between firmware and Linux req->queue_id.queue_id = 3 - queue_id; @@ -680,6 +487,8 @@ static int wfx_tx_inner(struct wfx_vif *wvif, struct ieee80211_sta *sta, // Auxiliary operations wfx_tx_manage_pm(wvif, hdr, tx_priv, sta); wfx_tx_queue_put(wvif->wdev, &wvif->wdev->tx_queue[queue_id], skb); + if (tx_info->flags & IEEE80211_TX_CTL_SEND_AFTER_DTIM) + schedule_work(&wvif->update_tim_work); wfx_bh_request_tx(wvif->wdev); return 0; } @@ -719,7 +528,7 @@ drop: ieee80211_tx_status_irqsafe(wdev->hw, skb); } -void wfx_tx_confirm_cb(struct wfx_vif *wvif, struct hif_cnf_tx *arg) +void wfx_tx_confirm_cb(struct wfx_vif *wvif, const struct hif_cnf_tx *arg) { int i; int tx_count; @@ -791,14 +600,11 @@ void wfx_tx_confirm_cb(struct wfx_vif *wvif, struct hif_cnf_tx *arg) else tx_info->flags |= IEEE80211_TX_STAT_ACK; } else if (arg->status == HIF_REQUEUE) { - /* "REQUEUE" means "implicit suspend" */ - struct hif_ind_suspend_resume_tx suspend = { - .suspend_resume_flags.resume = 0, - .suspend_resume_flags.bc_mc_only = 1, - }; - WARN(!arg->tx_result_flags.requeue, "incoherent status and result_flags"); - wfx_suspend_resume(wvif, &suspend); + if (tx_info->flags & IEEE80211_TX_CTL_SEND_AFTER_DTIM) { + wvif->after_dtim_tx_allowed = false; // DTIM period elapsed + schedule_work(&wvif->update_tim_work); + } tx_info->flags |= IEEE80211_TX_STAT_TX_FILTERED; } else { if (wvif->bss_loss_state && @@ -808,31 +614,25 @@ void wfx_tx_confirm_cb(struct wfx_vif *wvif, struct hif_cnf_tx *arg) wfx_pending_remove(wvif->wdev, skb); } -static void wfx_notify_buffered_tx(struct wfx_vif *wvif, struct sk_buff *skb, - struct hif_req_tx *req) +static void wfx_notify_buffered_tx(struct wfx_vif *wvif, struct sk_buff *skb) { - struct ieee80211_sta *sta; struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data; - int tid = wfx_tx_get_tid(hdr); - int raw_link_id = req->queue_id.peer_sta_id; - u8 *buffered; - - if (raw_link_id && tid < WFX_MAX_TID) { - buffered = wvif->link_id_db[raw_link_id - 1].buffered; - - spin_lock_bh(&wvif->ps_state_lock); - WARN(!buffered[tid], "inconsistent notification"); - buffered[tid]--; - spin_unlock_bh(&wvif->ps_state_lock); - - if (!buffered[tid]) { - rcu_read_lock(); - sta = ieee80211_find_sta(wvif->vif, hdr->addr1); - if (sta) - ieee80211_sta_set_buffered(sta, tid, false); - rcu_read_unlock(); - } + struct ieee80211_sta *sta; + struct wfx_sta_priv *sta_priv; + int tid = ieee80211_get_tid(hdr); + + rcu_read_lock(); // protect sta + sta = ieee80211_find_sta(wvif->vif, hdr->addr1); + if (sta) { + sta_priv = (struct wfx_sta_priv *)&sta->drv_priv; + spin_lock_bh(&sta_priv->lock); + WARN(!sta_priv->buffered[tid], "inconsistent notification"); + sta_priv->buffered[tid]--; + if (!sta_priv->buffered[tid]) + ieee80211_sta_set_buffered(sta, tid, false); + spin_unlock_bh(&sta_priv->lock); } + rcu_read_unlock(); } void wfx_skb_dtor(struct wfx_dev *wdev, struct sk_buff *skb) @@ -846,7 +646,7 @@ void wfx_skb_dtor(struct wfx_dev *wdev, struct sk_buff *skb) WARN_ON(!wvif); skb_pull(skb, offset); - wfx_notify_buffered_tx(wvif, skb, req); + wfx_notify_buffered_tx(wvif, skb); wfx_tx_policy_put(wvif, req->tx_flags.retry_policy_index); ieee80211_tx_status_irqsafe(wdev->hw, skb); } diff --git a/drivers/staging/wfx/data_tx.h b/drivers/staging/wfx/data_tx.h index 0fc388db62e0..04b2147101b6 100644 --- a/drivers/staging/wfx/data_tx.h +++ b/drivers/staging/wfx/data_tx.h @@ -14,29 +14,10 @@ #include "hif_api_cmd.h" #include "hif_api_mib.h" -// FIXME: use IEEE80211_NUM_TIDS -#define WFX_MAX_TID 8 - struct wfx_tx_priv; struct wfx_dev; struct wfx_vif; -enum wfx_link_status { - WFX_LINK_OFF, - WFX_LINK_RESERVE, - WFX_LINK_SOFT, - WFX_LINK_HARD, -}; - -struct wfx_link_entry { - unsigned long timestamp; - enum wfx_link_status status; - u8 mac[ETH_ALEN]; - u8 old_mac[ETH_ALEN]; - u8 buffered[WFX_MAX_TID]; - struct sk_buff_head rx_queue; -}; - struct tx_policy { struct list_head link; int usage_count; @@ -57,7 +38,6 @@ struct wfx_tx_priv { struct ieee80211_key_conf *hw_key; u8 link_id; u8 raw_link_id; - u8 tid; } __packed; void wfx_tx_policy_init(struct wfx_vif *wvif); @@ -65,14 +45,9 @@ void wfx_tx_policy_upload_work(struct work_struct *work); void wfx_tx(struct ieee80211_hw *hw, struct ieee80211_tx_control *control, struct sk_buff *skb); -void wfx_tx_confirm_cb(struct wfx_vif *wvif, struct hif_cnf_tx *arg); +void wfx_tx_confirm_cb(struct wfx_vif *wvif, const struct hif_cnf_tx *arg); void wfx_skb_dtor(struct wfx_dev *wdev, struct sk_buff *skb); -int wfx_unmap_link(struct wfx_vif *wvif, int link_id); -void wfx_link_id_work(struct work_struct *work); -void wfx_link_id_gc_work(struct work_struct *work); -int wfx_find_link_id(struct wfx_vif *wvif, const u8 *mac); - static inline struct wfx_tx_priv *wfx_skb_tx_priv(struct sk_buff *skb) { struct ieee80211_tx_info *tx_info; diff --git a/drivers/staging/wfx/debug.c b/drivers/staging/wfx/debug.c index d17a75242365..1164aba118a1 100644 --- a/drivers/staging/wfx/debug.c +++ b/drivers/staging/wfx/debug.c @@ -145,7 +145,7 @@ static int wfx_rx_stats_show(struct seq_file *seq, void *v) st->pwr_clk_freq, st->is_ext_pwr_clk ? "yes" : "no"); seq_printf(seq, - "N. of frames: %d, PER (x10e4): %d, Throughput: %dKbps/s\n", + "Num. of frames: %d, PER (x10e4): %d, Throughput: %dKbps/s\n", st->nb_rx_frame, st->per_total, st->throughput); seq_puts(seq, " Num. of PER RSSI SNR CFO\n"); seq_puts(seq, " frames (x10e4) (dBm) (dB) (kHz)\n"); diff --git a/drivers/staging/wfx/fwio.c b/drivers/staging/wfx/fwio.c index dbf8bda71ff7..9d61082c1e6c 100644 --- a/drivers/staging/wfx/fwio.c +++ b/drivers/staging/wfx/fwio.c @@ -61,7 +61,7 @@ #define DCA_TIMEOUT 50 // milliseconds #define WAKEUP_TIMEOUT 200 // milliseconds -static const char * const fwio_error_strings[] = { +static const char * const fwio_errors[] = { [ERR_INVALID_SEC_TYPE] = "Invalid section type or wrong encryption", [ERR_SIG_VERIF_FAILED] = "Signature verification failed", [ERR_AES_CTRL_KEY] = "AES control key not initialized", @@ -220,22 +220,16 @@ static int upload_firmware(struct wfx_dev *wdev, const u8 *data, size_t len) static void print_boot_status(struct wfx_dev *wdev) { - u32 val32; + u32 reg; - sram_reg_read(wdev, WFX_STATUS_INFO, &val32); - if (val32 == 0x12345678) { - dev_info(wdev->dev, "no error reported by secure boot\n"); - } else { - sram_reg_read(wdev, WFX_ERR_INFO, &val32); - if (val32 < ARRAY_SIZE(fwio_error_strings) && - fwio_error_strings[val32]) - dev_info(wdev->dev, "secure boot error: %s\n", - fwio_error_strings[val32]); - else - dev_info(wdev->dev, - "secure boot error: Unknown (0x%02x)\n", - val32); - } + sram_reg_read(wdev, WFX_STATUS_INFO, ®); + if (reg == 0x12345678) + return; + sram_reg_read(wdev, WFX_ERR_INFO, ®); + if (reg < ARRAY_SIZE(fwio_errors) && fwio_errors[reg]) + dev_info(wdev->dev, "secure boot: %s\n", fwio_errors[reg]); + else + dev_info(wdev->dev, "secure boot: Error %#02x\n", reg); } static int load_firmware_secure(struct wfx_dev *wdev) @@ -345,7 +339,7 @@ int wfx_init_device(struct wfx_dev *wdev) ktime_t now, start; u32 reg; - reg = CFG_DIRECT_ACCESS_MODE | CFG_CPU_RESET | CFG_WORD_MODE2; + reg = CFG_DIRECT_ACCESS_MODE | CFG_CPU_RESET | CFG_BYTE_ORDER_ABCD; if (wdev->pdata.use_rising_clk) reg |= CFG_CLK_RISE_EDGE; ret = config_reg_write(wdev, reg); diff --git a/drivers/staging/wfx/hif_api_cmd.h b/drivers/staging/wfx/hif_api_cmd.h index c15831de4ff4..5554d6eddbf3 100644 --- a/drivers/staging/wfx/hif_api_cmd.h +++ b/drivers/staging/wfx/hif_api_cmd.h @@ -137,7 +137,7 @@ struct hif_ie_tlv { struct hif_req_update_ie { struct hif_ie_flags ie_flags; - u16 num_i_es; + u16 num_ies; struct hif_ie_tlv ie[]; } __packed; @@ -180,7 +180,7 @@ struct hif_req_start_scan { struct hif_auto_scan_param auto_scan_param; u8 num_of_probe_requests; u8 probe_delay; - u8 num_of_ssi_ds; + u8 num_of_ssids; u8 num_of_channels; u32 min_channel_time; u32 max_channel_time; @@ -188,7 +188,7 @@ struct hif_req_start_scan { u8 ssid_and_channel_lists[]; } __packed; -struct hif_start_scan_req_cstnbssid_body { +struct hif_req_start_scan_alt { u8 band; struct hif_scan_type scan_type; struct hif_scan_flags scan_flags; @@ -196,7 +196,7 @@ struct hif_start_scan_req_cstnbssid_body { struct hif_auto_scan_param auto_scan_param; u8 num_of_probe_requests; u8 probe_delay; - u8 num_of_ssi_ds; + u8 num_of_ssids; u8 num_of_channels; u32 min_channel_time; u32 max_channel_time; @@ -253,7 +253,8 @@ struct hif_queue { struct hif_data_flags { u8 more:1; u8 fc_offset:3; - u8 reserved:4; + u8 after_dtim:1; + u8 reserved:3; } __packed; struct hif_tx_flags { @@ -377,17 +378,6 @@ struct hif_cnf_edca_queue_params { u32 status; } __packed; -enum hif_ap_mode { - HIF_MODE_IBSS = 0x0, - HIF_MODE_BSS = 0x1 -}; - -enum hif_preamble { - HIF_PREAMBLE_LONG = 0x0, - HIF_PREAMBLE_SHORT = 0x1, - HIF_PREAMBLE_SHORT_LONG12 = 0x2 -}; - struct hif_join_flags { u8 reserved1:2; u8 force_no_beacon:1; @@ -396,14 +386,16 @@ struct hif_join_flags { } __packed; struct hif_req_join { - u8 mode; + u8 infrastructure_bss_mode:1; + u8 reserved1:7; u8 band; u16 channel_number; u8 bssid[ETH_ALEN]; u16 atim_window; - u8 preamble_type; + u8 short_preamble:1; + u8 reserved2:7; u8 probe_for_join; - u8 reserved; + u8 reserved3; struct hif_join_flags join_flags; u32 ssid_length; u8 ssid[HIF_API_SSID_SIZE]; @@ -466,8 +458,9 @@ struct hif_req_start { u32 reserved1; u32 beacon_interval; u8 dtim_period; - u8 preamble_type; - u8 reserved2; + u8 short_preamble:1; + u8 reserved2:7; + u8 reserved3; u8 ssid_length; u8 ssid[HIF_API_SSID_SIZE]; u32 basic_rate_set; diff --git a/drivers/staging/wfx/hif_api_mib.h b/drivers/staging/wfx/hif_api_mib.h index 94b789ceb4ff..0c67cd4c1593 100644 --- a/drivers/staging/wfx/hif_api_mib.h +++ b/drivers/staging/wfx/hif_api_mib.h @@ -181,19 +181,13 @@ struct hif_mib_ipv6_addr_data_frame_condition { u8 i_pv6_address[HIF_API_IPV6_ADDRESS_SIZE]; } __packed; -union hif_addr_type { - u8 value; - struct { - u8 type_unicast:1; - u8 type_multicast:1; - u8 type_broadcast:1; - u8 reserved:5; - } bits; -}; +#define HIF_FILTER_UNICAST 0x1 +#define HIF_FILTER_MULTICAST 0x2 +#define HIF_FILTER_BROADCAST 0x4 struct hif_mib_uc_mc_bc_data_frame_condition { u8 condition_idx; - union hif_addr_type param; + u8 allowed_frames; u8 reserved[2]; } __packed; @@ -212,9 +206,11 @@ struct hif_mib_config_data_filter { } __packed; struct hif_mib_set_data_filtering { - u8 default_filter; - u8 enable; - u8 reserved[2]; + u8 invert_matching:1; + u8 reserved1:7; + u8 enable:1; + u8 reserved2:7; + u8 reserved3[2]; } __packed; enum hif_arp_ns_frame_treatment { @@ -395,11 +391,6 @@ struct hif_mib_non_erp_protection { u8 reserved2[3]; } __packed; -enum hif_tx_mode { - HIF_TX_MODE_MIXED = 0x0, - HIF_TX_MODE_GREENFIELD = 0x1 -}; - enum hif_tmplt { HIF_TMPLT_PRBREQ = 0x0, HIF_TMPLT_BCN = 0x1, @@ -471,9 +462,11 @@ struct hif_mib_set_association_mode { u8 mode:1; u8 rateset:1; u8 spacing:1; - u8 reserved:4; - u8 preamble_type; - u8 mixed_or_greenfield_type; + u8 reserved1:4; + u8 short_preamble:1; + u8 reserved2:7; + u8 greenfield:1; + u8 reserved3:7; u8 mpdu_start_spacing; u32 basic_rate_set; } __packed; diff --git a/drivers/staging/wfx/hif_rx.c b/drivers/staging/wfx/hif_rx.c index 820de216be0c..33c22c5d629d 100644 --- a/drivers/staging/wfx/hif_rx.c +++ b/drivers/staging/wfx/hif_rx.c @@ -18,8 +18,8 @@ #include "secure_link.h" #include "hif_api_cmd.h" -static int hif_generic_confirm(struct wfx_dev *wdev, struct hif_msg *hif, - void *buf) +static int hif_generic_confirm(struct wfx_dev *wdev, + const struct hif_msg *hif, const void *buf) { // All confirm messages start with status int status = le32_to_cpu(*((__le32 *) buf)); @@ -59,9 +59,10 @@ static int hif_generic_confirm(struct wfx_dev *wdev, struct hif_msg *hif, return status; } -static int hif_tx_confirm(struct wfx_dev *wdev, struct hif_msg *hif, void *buf) +static int hif_tx_confirm(struct wfx_dev *wdev, + const struct hif_msg *hif, const void *buf) { - struct hif_cnf_tx *body = buf; + const struct hif_cnf_tx *body = buf; struct wfx_vif *wvif = wdev_to_wvif(wdev, hif->interface); WARN_ON(!wvif); @@ -72,31 +73,27 @@ static int hif_tx_confirm(struct wfx_dev *wdev, struct hif_msg *hif, void *buf) return 0; } -static int hif_multi_tx_confirm(struct wfx_dev *wdev, struct hif_msg *hif, - void *buf) +static int hif_multi_tx_confirm(struct wfx_dev *wdev, + const struct hif_msg *hif, const void *buf) { - struct hif_cnf_multi_transmit *body = buf; - struct hif_cnf_tx *buf_loc = (struct hif_cnf_tx *) &body->tx_conf_payload; + const struct hif_cnf_multi_transmit *body = buf; struct wfx_vif *wvif = wdev_to_wvif(wdev, hif->interface); - int count = body->num_tx_confs; int i; - WARN(count <= 0, "corrupted message"); + WARN(body->num_tx_confs <= 0, "corrupted message"); WARN_ON(!wvif); if (!wvif) return -EFAULT; - for (i = 0; i < count; ++i) { - wfx_tx_confirm_cb(wvif, buf_loc); - buf_loc++; - } + for (i = 0; i < body->num_tx_confs; i++) + wfx_tx_confirm_cb(wvif, &body->tx_conf_payload[i]); return 0; } -static int hif_startup_indication(struct wfx_dev *wdev, struct hif_msg *hif, - void *buf) +static int hif_startup_indication(struct wfx_dev *wdev, + const struct hif_msg *hif, const void *buf) { - struct hif_ind_startup *body = buf; + const struct hif_ind_startup *body = buf; if (body->status || body->firmware_type > 4) { dev_err(wdev->dev, "received invalid startup indication"); @@ -112,8 +109,8 @@ static int hif_startup_indication(struct wfx_dev *wdev, struct hif_msg *hif, return 0; } -static int hif_wakeup_indication(struct wfx_dev *wdev, struct hif_msg *hif, - void *buf) +static int hif_wakeup_indication(struct wfx_dev *wdev, + const struct hif_msg *hif, const void *buf) { if (!wdev->pdata.gpio_wakeup || !gpiod_get_value(wdev->pdata.gpio_wakeup)) { @@ -123,25 +120,27 @@ static int hif_wakeup_indication(struct wfx_dev *wdev, struct hif_msg *hif, return 0; } -static int hif_keys_indication(struct wfx_dev *wdev, struct hif_msg *hif, - void *buf) +static int hif_keys_indication(struct wfx_dev *wdev, + const struct hif_msg *hif, const void *buf) { - struct hif_ind_sl_exchange_pub_keys *body = buf; + const struct hif_ind_sl_exchange_pub_keys *body = buf; + u8 pubkey[API_NCP_PUB_KEY_SIZE]; - // Compatibility with legacy secure link - if (body->status == SL_PUB_KEY_EXCHANGE_STATUS_SUCCESS) - body->status = 0; - if (body->status) + // SL_PUB_KEY_EXCHANGE_STATUS_SUCCESS is used by legacy secure link + if (body->status && body->status != SL_PUB_KEY_EXCHANGE_STATUS_SUCCESS) dev_warn(wdev->dev, "secure link negociation error\n"); - wfx_sl_check_pubkey(wdev, body->ncp_pub_key, body->ncp_pub_key_mac); + memcpy(pubkey, body->ncp_pub_key, sizeof(pubkey)); + memreverse(pubkey, sizeof(pubkey)); + wfx_sl_check_pubkey(wdev, pubkey, body->ncp_pub_key_mac); return 0; } -static int hif_receive_indication(struct wfx_dev *wdev, struct hif_msg *hif, - void *buf, struct sk_buff *skb) +static int hif_receive_indication(struct wfx_dev *wdev, + const struct hif_msg *hif, + const void *buf, struct sk_buff *skb) { struct wfx_vif *wvif = wdev_to_wvif(wdev, hif->interface); - struct hif_ind_rx *body = buf; + const struct hif_ind_rx *body = buf; if (!wvif) { dev_warn(wdev->dev, "ignore rx data for non-existent vif %d\n", @@ -154,11 +153,11 @@ static int hif_receive_indication(struct wfx_dev *wdev, struct hif_msg *hif, return 0; } -static int hif_event_indication(struct wfx_dev *wdev, struct hif_msg *hif, - void *buf) +static int hif_event_indication(struct wfx_dev *wdev, + const struct hif_msg *hif, const void *buf) { struct wfx_vif *wvif = wdev_to_wvif(wdev, hif->interface); - struct hif_ind_event *body = buf; + const struct hif_ind_event *body = buf; struct wfx_hif_event *event; int first; @@ -183,7 +182,8 @@ static int hif_event_indication(struct wfx_dev *wdev, struct hif_msg *hif, } static int hif_pm_mode_complete_indication(struct wfx_dev *wdev, - struct hif_msg *hif, void *buf) + const struct hif_msg *hif, + const void *buf) { struct wfx_vif *wvif = wdev_to_wvif(wdev, hif->interface); @@ -194,19 +194,20 @@ static int hif_pm_mode_complete_indication(struct wfx_dev *wdev, } static int hif_scan_complete_indication(struct wfx_dev *wdev, - struct hif_msg *hif, void *buf) + const struct hif_msg *hif, + const void *buf) { struct wfx_vif *wvif = wdev_to_wvif(wdev, hif->interface); - struct hif_ind_scan_cmpl *body = buf; WARN_ON(!wvif); - wfx_scan_complete_cb(wvif, body); + wfx_scan_complete(wvif); return 0; } static int hif_join_complete_indication(struct wfx_dev *wdev, - struct hif_msg *hif, void *buf) + const struct hif_msg *hif, + const void *buf) { struct wfx_vif *wvif = wdev_to_wvif(wdev, hif->interface); @@ -217,21 +218,26 @@ static int hif_join_complete_indication(struct wfx_dev *wdev, } static int hif_suspend_resume_indication(struct wfx_dev *wdev, - struct hif_msg *hif, void *buf) + const struct hif_msg *hif, + const void *buf) { struct wfx_vif *wvif = wdev_to_wvif(wdev, hif->interface); - struct hif_ind_suspend_resume_tx *body = buf; + const struct hif_ind_suspend_resume_tx *body = buf; WARN_ON(!wvif); - wfx_suspend_resume(wvif, body); + WARN(!body->suspend_resume_flags.bc_mc_only, "unsupported suspend/resume notification"); + if (body->suspend_resume_flags.resume) + wfx_suspend_resume_mc(wvif, STA_NOTIFY_AWAKE); + else + wfx_suspend_resume_mc(wvif, STA_NOTIFY_SLEEP); return 0; } -static int hif_error_indication(struct wfx_dev *wdev, struct hif_msg *hif, - void *buf) +static int hif_error_indication(struct wfx_dev *wdev, + const struct hif_msg *hif, const void *buf) { - struct hif_ind_error *body = buf; + const struct hif_ind_error *body = buf; u8 *pRollback = (u8 *) body->data; u32 *pStatus = (u32 *) body->data; @@ -268,10 +274,10 @@ static int hif_error_indication(struct wfx_dev *wdev, struct hif_msg *hif, return 0; } -static int hif_generic_indication(struct wfx_dev *wdev, struct hif_msg *hif, - void *buf) +static int hif_generic_indication(struct wfx_dev *wdev, + const struct hif_msg *hif, const void *buf) { - struct hif_ind_generic *body = buf; + const struct hif_ind_generic *body = buf; switch (body->indication_type) { case HIF_GENERIC_INDICATION_TYPE_RAW: @@ -299,9 +305,10 @@ static int hif_generic_indication(struct wfx_dev *wdev, struct hif_msg *hif, } static int hif_exception_indication(struct wfx_dev *wdev, - struct hif_msg *hif, void *buf) + const struct hif_msg *hif, const void *buf) { size_t len = hif->len - 4; // drop header + dev_err(wdev->dev, "firmware exception\n"); print_hex_dump_bytes("Dump: ", DUMP_PREFIX_NONE, buf, len); wdev->chip_frozen = 1; @@ -311,7 +318,8 @@ static int hif_exception_indication(struct wfx_dev *wdev, static const struct { int msg_id; - int (*handler)(struct wfx_dev *wdev, struct hif_msg *hif, void *buf); + int (*handler)(struct wfx_dev *wdev, + const struct hif_msg *hif, const void *buf); } hif_handlers[] = { /* Confirmations */ { HIF_CNF_ID_TX, hif_tx_confirm }, @@ -335,7 +343,7 @@ static const struct { void wfx_handle_rx(struct wfx_dev *wdev, struct sk_buff *skb) { int i; - struct hif_msg *hif = (struct hif_msg *) skb->data; + const struct hif_msg *hif = (const struct hif_msg *)skb->data; int hif_id = hif->id; if (hif_id == HIF_IND_ID_RX) { @@ -358,7 +366,12 @@ void wfx_handle_rx(struct wfx_dev *wdev, struct sk_buff *skb) goto free; } } - dev_err(wdev->dev, "unsupported HIF ID %02x\n", hif_id); + if (hif_id & 0x80) + dev_err(wdev->dev, "unsupported HIF indication: ID %02x\n", + hif_id); + else + dev_err(wdev->dev, "unexpected HIF confirmation: ID %02x\n", + hif_id); free: dev_kfree_skb(skb); } diff --git a/drivers/staging/wfx/hif_tx.c b/drivers/staging/wfx/hif_tx.c index cb7cddcb9815..2428363371fa 100644 --- a/drivers/staging/wfx/hif_tx.c +++ b/drivers/staging/wfx/hif_tx.c @@ -6,7 +6,6 @@ * Copyright (c) 2017-2019, Silicon Laboratories, Inc. * Copyright (c) 2010, ST-Ericsson */ -#include <linux/skbuff.h> #include <linux/etherdevice.h> #include "hif_tx.h" @@ -221,41 +220,59 @@ int hif_write_mib(struct wfx_dev *wdev, int vif_id, u16 mib_id, void *val, return ret; } -int hif_scan(struct wfx_vif *wvif, const struct wfx_scan_params *arg) +int hif_scan(struct wfx_vif *wvif, struct cfg80211_scan_request *req, + int chan_start_idx, int chan_num) { int ret, i; struct hif_msg *hif; - struct hif_ssid_def *ssids; - size_t buf_len = sizeof(struct hif_req_start_scan) + - arg->scan_req.num_of_channels * sizeof(u8) + - arg->scan_req.num_of_ssi_ds * sizeof(struct hif_ssid_def); - struct hif_req_start_scan *body = wfx_alloc_hif(buf_len, &hif); - u8 *ptr = (u8 *) body + sizeof(*body); - - WARN(arg->scan_req.num_of_channels > HIF_API_MAX_NB_CHANNELS, "invalid params"); - WARN(arg->scan_req.num_of_ssi_ds > 2, "invalid params"); - WARN(arg->scan_req.band > 1, "invalid params"); - - // FIXME: This API is unnecessary complex, fixing NumOfChannels and - // adding a member SsidDef at end of struct hif_req_start_scan would - // simplify that a lot. - memcpy(body, &arg->scan_req, sizeof(*body)); - cpu_to_le32s(&body->min_channel_time); - cpu_to_le32s(&body->max_channel_time); - cpu_to_le32s(&body->tx_power_level); - memcpy(ptr, arg->ssids, - arg->scan_req.num_of_ssi_ds * sizeof(struct hif_ssid_def)); - ssids = (struct hif_ssid_def *) ptr; - for (i = 0; i < body->num_of_ssi_ds; ++i) - cpu_to_le32s(&ssids[i].ssid_length); - ptr += arg->scan_req.num_of_ssi_ds * sizeof(struct hif_ssid_def); - memcpy(ptr, arg->ch, arg->scan_req.num_of_channels * sizeof(u8)); - ptr += arg->scan_req.num_of_channels * sizeof(u8); - WARN(buf_len != ptr - (u8 *) body, "allocation size mismatch"); + size_t buf_len = + sizeof(struct hif_req_start_scan_alt) + chan_num * sizeof(u8); + struct hif_req_start_scan_alt *body = wfx_alloc_hif(buf_len, &hif); + int tmo_chan_fg, tmo_chan_bg, tmo; + + WARN(chan_num > HIF_API_MAX_NB_CHANNELS, "invalid params"); + WARN(req->n_ssids > HIF_API_MAX_NB_SSIDS, "invalid params"); + + compiletime_assert(IEEE80211_MAX_SSID_LEN == HIF_API_SSID_SIZE, + "API inconsistency"); + for (i = 0; i < req->n_ssids; i++) { + memcpy(body->ssid_def[i].ssid, req->ssids[i].ssid, + IEEE80211_MAX_SSID_LEN); + body->ssid_def[i].ssid_length = + cpu_to_le32(req->ssids[i].ssid_len); + } + body->num_of_ssids = HIF_API_MAX_NB_SSIDS; + // Background scan is always a good idea + body->scan_type.type = 1; + body->scan_flags.fbg = 1; + body->tx_power_level = + cpu_to_le32(req->channels[chan_start_idx]->max_power); + body->num_of_channels = chan_num; + for (i = 0; i < chan_num; i++) + body->channel_list[i] = + req->channels[i + chan_start_idx]->hw_value; + if (req->no_cck) + body->max_transmit_rate = API_RATE_INDEX_G_6MBPS; + else + body->max_transmit_rate = API_RATE_INDEX_B_1MBPS; + if (req->channels[chan_start_idx]->flags & IEEE80211_CHAN_NO_IR) { + body->min_channel_time = cpu_to_le32(50); + body->max_channel_time = cpu_to_le32(150); + } else { + body->min_channel_time = cpu_to_le32(10); + body->max_channel_time = cpu_to_le32(50); + body->num_of_probe_requests = 2; + body->probe_delay = 100; + } + tmo_chan_bg = le32_to_cpu(body->max_channel_time) * USEC_PER_TU; + tmo_chan_fg = 512 * USEC_PER_TU + body->probe_delay; + tmo_chan_fg *= body->num_of_probe_requests; + tmo = chan_num * max(tmo_chan_bg, tmo_chan_fg); + wfx_fill_header(hif, wvif->id, HIF_REQ_ID_START_SCAN, buf_len); ret = wfx_cmd_send(wvif->wdev, hif, NULL, 0, false); kfree(hif); - return ret; + return ret ? ret : usecs_to_jiffies(tmo); } int hif_stop_scan(struct wfx_vif *wvif) @@ -271,18 +288,29 @@ int hif_stop_scan(struct wfx_vif *wvif) return ret; } -int hif_join(struct wfx_vif *wvif, const struct hif_req_join *arg) +int hif_join(struct wfx_vif *wvif, const struct ieee80211_bss_conf *conf, + const struct ieee80211_channel *channel, const u8 *ssidie) { int ret; struct hif_msg *hif; struct hif_req_join *body = wfx_alloc_hif(sizeof(*body), &hif); - memcpy(body, arg, sizeof(struct hif_req_join)); - cpu_to_le16s(&body->channel_number); - cpu_to_le16s(&body->atim_window); - cpu_to_le32s(&body->ssid_length); - cpu_to_le32s(&body->beacon_interval); - cpu_to_le32s(&body->basic_rate_set); + WARN_ON(!conf->basic_rates); + body->infrastructure_bss_mode = !conf->ibss_joined; + body->short_preamble = conf->use_short_preamble; + if (channel && channel->flags & IEEE80211_CHAN_NO_IR) + body->probe_for_join = 0; + else + body->probe_for_join = 1; + body->channel_number = cpu_to_le16(channel->hw_value); + body->beacon_interval = cpu_to_le32(conf->beacon_int); + body->basic_rate_set = + cpu_to_le32(wfx_rate_mask_to_hw(wvif->wdev, conf->basic_rates)); + memcpy(body->bssid, conf->bssid, sizeof(body->bssid)); + if (!conf->ibss_joined && ssidie) { + body->ssid_length = cpu_to_le32(ssidie[1]); + memcpy(body->ssid, &ssidie[2], ssidie[1]); + } wfx_fill_header(hif, wvif->id, HIF_REQ_ID_JOIN, sizeof(*body)); ret = wfx_cmd_send(wvif->wdev, hif, NULL, 0, false); kfree(hif); @@ -341,19 +369,28 @@ int hif_remove_key(struct wfx_dev *wdev, int idx) return ret; } -int hif_set_edca_queue_params(struct wfx_vif *wvif, - const struct hif_req_edca_queue_params *arg) +int hif_set_edca_queue_params(struct wfx_vif *wvif, u16 queue, + const struct ieee80211_tx_queue_params *arg) { int ret; struct hif_msg *hif; struct hif_req_edca_queue_params *body = wfx_alloc_hif(sizeof(*body), &hif); - // NOTE: queues numerotation are not the same between WFx and Linux - memcpy(body, arg, sizeof(*body)); - cpu_to_le16s(&body->cw_min); - cpu_to_le16s(&body->cw_max); - cpu_to_le16s(&body->tx_op_limit); + if (!body) + return -ENOMEM; + + WARN_ON(arg->aifs > 255); + body->aifsn = arg->aifs; + body->cw_min = cpu_to_le16(arg->cw_min); + body->cw_max = cpu_to_le16(arg->cw_max); + body->tx_op_limit = cpu_to_le16(arg->txop * USEC_PER_TXOP); + body->queue_id = 3 - queue; + // API 2.0 has changed queue IDs values + if (wfx_api_older_than(wvif->wdev, 2, 0) && queue == IEEE80211_AC_BE) + body->queue_id = HIF_QUEUE_ID_BACKGROUND; + if (wfx_api_older_than(wvif->wdev, 2, 0) && queue == IEEE80211_AC_BK) + body->queue_id = HIF_QUEUE_ID_BESTEFFORT; wfx_fill_header(hif, wvif->id, HIF_REQ_ID_EDCA_QUEUE_PARAMS, sizeof(*body)); ret = wfx_cmd_send(wvif->wdev, hif, NULL, 0, false); @@ -361,43 +398,57 @@ int hif_set_edca_queue_params(struct wfx_vif *wvif, return ret; } -int hif_set_pm(struct wfx_vif *wvif, const struct hif_req_set_pm_mode *arg) +int hif_set_pm(struct wfx_vif *wvif, bool ps, int dynamic_ps_timeout) { int ret; struct hif_msg *hif; struct hif_req_set_pm_mode *body = wfx_alloc_hif(sizeof(*body), &hif); - memcpy(body, arg, sizeof(*body)); + if (!body) + return -ENOMEM; + + if (ps) { + body->pm_mode.enter_psm = 1; + // Firmware does not support more than 128ms + body->fast_psm_idle_period = min(dynamic_ps_timeout * 2, 255); + if (body->fast_psm_idle_period) + body->pm_mode.fast_psm = 1; + } wfx_fill_header(hif, wvif->id, HIF_REQ_ID_SET_PM_MODE, sizeof(*body)); ret = wfx_cmd_send(wvif->wdev, hif, NULL, 0, false); kfree(hif); return ret; } -int hif_start(struct wfx_vif *wvif, const struct hif_req_start *arg) +int hif_start(struct wfx_vif *wvif, const struct ieee80211_bss_conf *conf, + const struct ieee80211_channel *channel) { int ret; struct hif_msg *hif; struct hif_req_start *body = wfx_alloc_hif(sizeof(*body), &hif); - memcpy(body, arg, sizeof(*body)); - cpu_to_le16s(&body->channel_number); - cpu_to_le32s(&body->beacon_interval); - cpu_to_le32s(&body->basic_rate_set); + body->dtim_period = conf->dtim_period, + body->short_preamble = conf->use_short_preamble, + body->channel_number = cpu_to_le16(channel->hw_value), + body->beacon_interval = cpu_to_le32(conf->beacon_int); + body->basic_rate_set = + cpu_to_le32(wfx_rate_mask_to_hw(wvif->wdev, conf->basic_rates)); + body->ssid_length = conf->ssid_len; + memcpy(body->ssid, conf->ssid, conf->ssid_len); wfx_fill_header(hif, wvif->id, HIF_REQ_ID_START, sizeof(*body)); ret = wfx_cmd_send(wvif->wdev, hif, NULL, 0, false); kfree(hif); return ret; } -int hif_beacon_transmit(struct wfx_vif *wvif, bool enable_beaconing) +int hif_beacon_transmit(struct wfx_vif *wvif, bool enable) { int ret; struct hif_msg *hif; struct hif_req_beacon_transmit *body = wfx_alloc_hif(sizeof(*body), &hif); - body->enable_beaconing = enable_beaconing ? 1 : 0; + body->enable_beaconing = enable ? 1 : 0; wfx_fill_header(hif, wvif->id, HIF_REQ_ID_BEACON_TRANSMIT, sizeof(*body)); ret = wfx_cmd_send(wvif->wdev, hif, NULL, 0, false); @@ -421,16 +472,15 @@ int hif_map_link(struct wfx_vif *wvif, u8 *mac_addr, int flags, int sta_id) return ret; } -int hif_update_ie(struct wfx_vif *wvif, const struct hif_ie_flags *target_frame, - const u8 *ies, size_t ies_len) +int hif_update_ie_beacon(struct wfx_vif *wvif, const u8 *ies, size_t ies_len) { int ret; struct hif_msg *hif; int buf_len = sizeof(struct hif_req_update_ie) + ies_len; struct hif_req_update_ie *body = wfx_alloc_hif(buf_len, &hif); - memcpy(&body->ie_flags, target_frame, sizeof(struct hif_ie_flags)); - body->num_i_es = cpu_to_le16(1); + body->ie_flags.beacon = 1; + body->num_ies = cpu_to_le16(1); memcpy(body->ie, ies, ies_len); wfx_fill_header(hif, wvif->id, HIF_REQ_ID_UPDATE_IE, buf_len); ret = wfx_cmd_send(wvif->wdev, hif, NULL, 0, false); diff --git a/drivers/staging/wfx/hif_tx.h b/drivers/staging/wfx/hif_tx.h index f61ae7b0d41c..20977e461718 100644 --- a/drivers/staging/wfx/hif_tx.h +++ b/drivers/staging/wfx/hif_tx.h @@ -12,15 +12,13 @@ #include "hif_api_cmd.h" +struct ieee80211_channel; +struct ieee80211_bss_conf; +struct ieee80211_tx_queue_params; +struct cfg80211_scan_request; struct wfx_dev; struct wfx_vif; -struct wfx_scan_params { - struct hif_req_start_scan scan_req; - struct hif_ssid_def *ssids; - u8 *ch; -}; - struct wfx_hif_cmd { struct mutex lock; struct mutex key_renew_lock; @@ -44,21 +42,23 @@ int hif_read_mib(struct wfx_dev *wdev, int vif_id, u16 mib_id, void *buf, size_t buf_size); int hif_write_mib(struct wfx_dev *wdev, int vif_id, u16 mib_id, void *buf, size_t buf_size); -int hif_scan(struct wfx_vif *wvif, const struct wfx_scan_params *arg); +int hif_scan(struct wfx_vif *wvif, struct cfg80211_scan_request *req80211, + int chan_start, int chan_num); int hif_stop_scan(struct wfx_vif *wvif); -int hif_join(struct wfx_vif *wvif, const struct hif_req_join *arg); -int hif_set_pm(struct wfx_vif *wvif, const struct hif_req_set_pm_mode *arg); +int hif_join(struct wfx_vif *wvif, const struct ieee80211_bss_conf *conf, + const struct ieee80211_channel *channel, const u8 *ssidie); +int hif_set_pm(struct wfx_vif *wvif, bool ps, int dynamic_ps_timeout); int hif_set_bss_params(struct wfx_vif *wvif, const struct hif_req_set_bss_params *arg); int hif_add_key(struct wfx_dev *wdev, const struct hif_req_add_key *arg); int hif_remove_key(struct wfx_dev *wdev, int idx); -int hif_set_edca_queue_params(struct wfx_vif *wvif, - const struct hif_req_edca_queue_params *arg); -int hif_start(struct wfx_vif *wvif, const struct hif_req_start *arg); +int hif_set_edca_queue_params(struct wfx_vif *wvif, u16 queue, + const struct ieee80211_tx_queue_params *arg); +int hif_start(struct wfx_vif *wvif, const struct ieee80211_bss_conf *conf, + const struct ieee80211_channel *channel); int hif_beacon_transmit(struct wfx_vif *wvif, bool enable); int hif_map_link(struct wfx_vif *wvif, u8 *mac_addr, int flags, int sta_id); -int hif_update_ie(struct wfx_vif *wvif, const struct hif_ie_flags *target_frame, - const u8 *ies, size_t ies_len); +int hif_update_ie_beacon(struct wfx_vif *wvif, const u8 *ies, size_t ies_len); int hif_sl_set_mac_key(struct wfx_dev *wdev, const u8 *slk_key, int destination); int hif_sl_config(struct wfx_dev *wdev, const unsigned long *bitmap); diff --git a/drivers/staging/wfx/hif_tx_mib.h b/drivers/staging/wfx/hif_tx_mib.h index 9be74881c56c..bf3769c2a9b6 100644 --- a/drivers/staging/wfx/hif_tx_mib.h +++ b/drivers/staging/wfx/hif_tx_mib.h @@ -15,13 +15,15 @@ #include "hif_tx.h" #include "hif_api_mib.h" -static inline int hif_set_output_power(struct wfx_vif *wvif, int power_level) +static inline int hif_set_output_power(struct wfx_vif *wvif, int val) { - __le32 val = cpu_to_le32(power_level); + struct hif_mib_current_tx_power_level arg = { + .power_level = cpu_to_le32(val * 10), + }; return hif_write_mib(wvif->wdev, wvif->id, HIF_MIB_ID_CURRENT_TX_POWER_LEVEL, - &val, sizeof(val)); + &arg, sizeof(arg)); } static inline int hif_set_beacon_wakeup_period(struct wfx_vif *wvif, @@ -42,10 +44,25 @@ static inline int hif_set_beacon_wakeup_period(struct wfx_vif *wvif, } static inline int hif_set_rcpi_rssi_threshold(struct wfx_vif *wvif, - struct hif_mib_rcpi_rssi_threshold *arg) + int rssi_thold, int rssi_hyst) { + struct hif_mib_rcpi_rssi_threshold arg = { + .rolling_average_count = 8, + .detection = 1, + }; + + if (!rssi_thold && !rssi_hyst) { + arg.upperthresh = 1; + arg.lowerthresh = 1; + } else { + arg.upper_threshold = rssi_thold + rssi_hyst; + arg.upper_threshold = (arg.upper_threshold + 110) * 2; + arg.lower_threshold = rssi_thold; + arg.lower_threshold = (arg.lower_threshold + 110) * 2; + } + return hif_write_mib(wvif->wdev, wvif->id, - HIF_MIB_ID_RCPI_RSSI_THRESHOLD, arg, sizeof(*arg)); + HIF_MIB_ID_RCPI_RSSI_THRESHOLD, &arg, sizeof(arg)); } static inline int hif_get_counters_table(struct wfx_dev *wdev, @@ -130,8 +147,17 @@ static inline int hif_set_operational_mode(struct wfx_dev *wdev, } static inline int hif_set_template_frame(struct wfx_vif *wvif, - struct hif_mib_template_frame *arg) + struct sk_buff *skb, + u8 frame_type, int init_rate) { + struct hif_mib_template_frame *arg; + + skb_push(skb, 4); + arg = (struct hif_mib_template_frame *)skb->data; + skb_pull(skb, 4); + arg->init_rate = init_rate; + arg->frame_type = frame_type; + arg->frame_length = cpu_to_le16(skb->len); return hif_write_mib(wvif->wdev, wvif->id, HIF_MIB_ID_TEMPLATE_FRAME, arg, sizeof(*arg)); } @@ -165,50 +191,105 @@ static inline int hif_set_block_ack_policy(struct wfx_vif *wvif, } static inline int hif_set_association_mode(struct wfx_vif *wvif, - struct hif_mib_set_association_mode *arg) + struct ieee80211_bss_conf *info, + struct ieee80211_sta_ht_cap *ht_cap) { + int basic_rates = wfx_rate_mask_to_hw(wvif->wdev, info->basic_rates); + struct hif_mib_set_association_mode val = { + .preambtype_use = 1, + .mode = 1, + .rateset = 1, + .spacing = 1, + .short_preamble = info->use_short_preamble, + .basic_rate_set = cpu_to_le32(basic_rates) + }; + + // FIXME: it is strange to not retrieve all information from bss_info + if (ht_cap && ht_cap->ht_supported) { + val.mpdu_start_spacing = ht_cap->ampdu_density; + if (!(info->ht_operation_mode & IEEE80211_HT_OP_MODE_NON_GF_STA_PRSNT)) + val.greenfield = !!(ht_cap->cap & IEEE80211_HT_CAP_GRN_FLD); + } + return hif_write_mib(wvif->wdev, wvif->id, - HIF_MIB_ID_SET_ASSOCIATION_MODE, arg, sizeof(*arg)); + HIF_MIB_ID_SET_ASSOCIATION_MODE, &val, sizeof(val)); } static inline int hif_set_tx_rate_retry_policy(struct wfx_vif *wvif, - struct hif_mib_set_tx_rate_retry_policy *arg) + int policy_index, uint8_t *rates) { - size_t size = struct_size(arg, tx_rate_retry_policy, - arg->num_tx_rate_policies); + struct hif_mib_set_tx_rate_retry_policy *arg; + size_t size = struct_size(arg, tx_rate_retry_policy, 1); + int ret; - return hif_write_mib(wvif->wdev, wvif->id, - HIF_MIB_ID_SET_TX_RATE_RETRY_POLICY, arg, size); + arg = kzalloc(size, GFP_KERNEL); + arg->num_tx_rate_policies = 1; + arg->tx_rate_retry_policy[0].policy_index = policy_index; + arg->tx_rate_retry_policy[0].short_retry_count = 255; + arg->tx_rate_retry_policy[0].long_retry_count = 255; + arg->tx_rate_retry_policy[0].first_rate_sel = 1; + arg->tx_rate_retry_policy[0].terminate = 1; + arg->tx_rate_retry_policy[0].count_init = 1; + memcpy(&arg->tx_rate_retry_policy[0].rates, rates, + sizeof(arg->tx_rate_retry_policy[0].rates)); + ret = hif_write_mib(wvif->wdev, wvif->id, + HIF_MIB_ID_SET_TX_RATE_RETRY_POLICY, arg, size); + kfree(arg); + return ret; } static inline int hif_set_mac_addr_condition(struct wfx_vif *wvif, - struct hif_mib_mac_addr_data_frame_condition *arg) + int idx, const u8 *mac_addr) { + struct hif_mib_mac_addr_data_frame_condition val = { + .condition_idx = idx, + .address_type = HIF_MAC_ADDR_A1, + }; + + ether_addr_copy(val.mac_address, mac_addr); return hif_write_mib(wvif->wdev, wvif->id, HIF_MIB_ID_MAC_ADDR_DATAFRAME_CONDITION, - arg, sizeof(*arg)); + &val, sizeof(val)); } static inline int hif_set_uc_mc_bc_condition(struct wfx_vif *wvif, - struct hif_mib_uc_mc_bc_data_frame_condition *arg) + int idx, u8 allowed_frames) { + struct hif_mib_uc_mc_bc_data_frame_condition val = { + .condition_idx = idx, + .allowed_frames = allowed_frames, + }; + return hif_write_mib(wvif->wdev, wvif->id, HIF_MIB_ID_UC_MC_BC_DATAFRAME_CONDITION, - arg, sizeof(*arg)); + &val, sizeof(val)); } -static inline int hif_set_config_data_filter(struct wfx_vif *wvif, - struct hif_mib_config_data_filter *arg) +static inline int hif_set_config_data_filter(struct wfx_vif *wvif, bool enable, + int idx, int mac_filters, + int frames_types_filters) { + struct hif_mib_config_data_filter val = { + .enable = enable, + .filter_idx = idx, + .mac_cond = mac_filters, + .uc_mc_bc_cond = frames_types_filters, + }; + return hif_write_mib(wvif->wdev, wvif->id, - HIF_MIB_ID_CONFIG_DATA_FILTER, arg, sizeof(*arg)); + HIF_MIB_ID_CONFIG_DATA_FILTER, &val, sizeof(val)); } static inline int hif_set_data_filtering(struct wfx_vif *wvif, - struct hif_mib_set_data_filtering *arg) + bool enable, bool invert) { + struct hif_mib_set_data_filtering val = { + .enable = enable, + .invert_matching = invert, + }; + return hif_write_mib(wvif->wdev, wvif->id, - HIF_MIB_ID_SET_DATA_FILTERING, arg, sizeof(*arg)); + HIF_MIB_ID_SET_DATA_FILTERING, &val, sizeof(val)); } static inline int hif_keep_alive_period(struct wfx_vif *wvif, int period) @@ -221,34 +302,56 @@ static inline int hif_keep_alive_period(struct wfx_vif *wvif, int period) &arg, sizeof(arg)); }; -static inline int hif_set_arp_ipv4_filter(struct wfx_vif *wvif, - struct hif_mib_arp_ip_addr_table *fp) +static inline int hif_set_arp_ipv4_filter(struct wfx_vif *wvif, int idx, + __be32 *addr) { + struct hif_mib_arp_ip_addr_table arg = { + .condition_idx = idx, + .arp_enable = HIF_ARP_NS_FILTERING_DISABLE, + }; + + if (addr) { + // Caution: type of addr is __be32 + memcpy(arg.ipv4_address, addr, sizeof(arg.ipv4_address)); + arg.arp_enable = HIF_ARP_NS_FILTERING_ENABLE; + } return hif_write_mib(wvif->wdev, wvif->id, HIF_MIB_ID_ARP_IP_ADDRESSES_TABLE, - fp, sizeof(*fp)); + &arg, sizeof(arg)); } -static inline int hif_use_multi_tx_conf(struct wfx_dev *wdev, - bool enabled) +static inline int hif_use_multi_tx_conf(struct wfx_dev *wdev, bool enable) { - __le32 arg = enabled ? cpu_to_le32(1) : 0; + struct hif_mib_gl_set_multi_msg arg = { + .enable_multi_tx_conf = enable, + }; return hif_write_mib(wdev, -1, HIF_MIB_ID_GL_SET_MULTI_MSG, &arg, sizeof(arg)); } -static inline int hif_set_uapsd_info(struct wfx_vif *wvif, - struct hif_mib_set_uapsd_information *arg) +static inline int hif_set_uapsd_info(struct wfx_vif *wvif, unsigned long val) { + struct hif_mib_set_uapsd_information arg = { }; + + if (val & BIT(IEEE80211_AC_VO)) + arg.trig_voice = 1; + if (val & BIT(IEEE80211_AC_VI)) + arg.trig_video = 1; + if (val & BIT(IEEE80211_AC_BE)) + arg.trig_be = 1; + if (val & BIT(IEEE80211_AC_BK)) + arg.trig_bckgrnd = 1; return hif_write_mib(wvif->wdev, wvif->id, HIF_MIB_ID_SET_UAPSD_INFORMATION, - arg, sizeof(*arg)); + &arg, sizeof(arg)); } static inline int hif_erp_use_protection(struct wfx_vif *wvif, bool enable) { - __le32 arg = enable ? cpu_to_le32(1) : 0; + struct hif_mib_non_erp_protection arg = { + .use_cts_to_self = enable, + }; return hif_write_mib(wvif->wdev, wvif->id, HIF_MIB_ID_NON_ERP_PROTECTION, &arg, sizeof(arg)); @@ -256,16 +359,18 @@ static inline int hif_erp_use_protection(struct wfx_vif *wvif, bool enable) static inline int hif_slot_time(struct wfx_vif *wvif, int val) { - __le32 arg = cpu_to_le32(val); + struct hif_mib_slot_time arg = { + .slot_time = cpu_to_le32(val), + }; return hif_write_mib(wvif->wdev, wvif->id, HIF_MIB_ID_SLOT_TIME, &arg, sizeof(arg)); } -static inline int hif_dual_cts_protection(struct wfx_vif *wvif, bool val) +static inline int hif_dual_cts_protection(struct wfx_vif *wvif, bool enable) { struct hif_mib_set_ht_protection arg = { - .dual_cts_prot = val, + .dual_cts_prot = enable, }; return hif_write_mib(wvif->wdev, wvif->id, HIF_MIB_ID_SET_HT_PROTECTION, @@ -274,7 +379,9 @@ static inline int hif_dual_cts_protection(struct wfx_vif *wvif, bool val) static inline int hif_wep_default_key_id(struct wfx_vif *wvif, int val) { - __le32 arg = cpu_to_le32(val); + struct hif_mib_wep_default_key_id arg = { + .wep_default_key_id = val, + }; return hif_write_mib(wvif->wdev, wvif->id, HIF_MIB_ID_DOT11_WEP_DEFAULT_KEY_ID, @@ -283,7 +390,9 @@ static inline int hif_wep_default_key_id(struct wfx_vif *wvif, int val) static inline int hif_rts_threshold(struct wfx_vif *wvif, int val) { - __le32 arg = cpu_to_le32(val > 0 ? val : 0xFFFF); + struct hif_mib_dot11_rts_threshold arg = { + .threshold = cpu_to_le32(val >= 0 ? val : 0xFFFF), + }; return hif_write_mib(wvif->wdev, wvif->id, HIF_MIB_ID_DOT11_RTS_THRESHOLD, &arg, sizeof(arg)); diff --git a/drivers/staging/wfx/hwio.h b/drivers/staging/wfx/hwio.h index b2c1a66de963..4b6ef061b40b 100644 --- a/drivers/staging/wfx/hwio.h +++ b/drivers/staging/wfx/hwio.h @@ -37,16 +37,11 @@ int ahb_reg_write(struct wfx_dev *wdev, u32 addr, u32 val); #define CFG_ERR_HOST_NO_IN_QUEUE 0x00000040 #define CFG_ERR_HOST_CRC_MISS 0x00000080 // only with SDIO #define CFG_SPI_IGNORE_CS 0x00000080 // only with SPI -/* Bytes ordering (only writable in SPI): */ -#define CFG_WORD_MODE_MASK 0x00000300 -/* - * B1,B0,B3,B2 (In SPI, register address and - * CONFIG data always use this mode) - */ -#define CFG_WORD_MODE0 0x00000000 -#define CFG_WORD_MODE1 0x00000100 // B3,B2,B1,B0 -#define CFG_WORD_MODE2 0x00000200 // B0,B1,B2,B3 (SDIO) -#define CFG_DIRECT_ACCESS_MODE 0x00000400 // Direct or queue access mode +#define CFG_BYTE_ORDER_MASK 0x00000300 // only writable with SPI +#define CFG_BYTE_ORDER_BADC 0x00000000 +#define CFG_BYTE_ORDER_DCBA 0x00000100 +#define CFG_BYTE_ORDER_ABCD 0x00000200 // SDIO always use this value +#define CFG_DIRECT_ACCESS_MODE 0x00000400 #define CFG_PREFETCH_AHB 0x00000800 #define CFG_DISABLE_CPU_CLK 0x00001000 #define CFG_PREFETCH_SRAM 0x00002000 diff --git a/drivers/staging/wfx/main.c b/drivers/staging/wfx/main.c index 3b47b6c21ea1..84adad64fc30 100644 --- a/drivers/staging/wfx/main.c +++ b/drivers/staging/wfx/main.c @@ -131,10 +131,11 @@ static const struct ieee80211_ops wfx_ops = { .stop = wfx_stop, .add_interface = wfx_add_interface, .remove_interface = wfx_remove_interface, - .config = wfx_config, + .config = wfx_config, .tx = wfx_tx, .conf_tx = wfx_conf_tx, .hw_scan = wfx_hw_scan, + .cancel_hw_scan = wfx_cancel_hw_scan, .sta_add = wfx_sta_add, .sta_remove = wfx_sta_remove, .sta_notify = wfx_sta_notify, @@ -182,7 +183,7 @@ struct gpio_desc *wfx_get_gpio(struct device *dev, int override, } else { ret = devm_gpiod_get(dev, label, GPIOD_OUT_LOW); } - if (IS_ERR(ret) || !ret) { + if (IS_ERR_OR_NULL(ret)) { if (!ret || PTR_ERR(ret) == -ENOENT) dev_warn(dev, "gpio %s is not defined\n", label); else @@ -297,6 +298,11 @@ struct wfx_dev *wfx_init_common(struct device *dev, hw->wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION) | BIT(NL80211_IFTYPE_ADHOC) | BIT(NL80211_IFTYPE_AP); + hw->wiphy->probe_resp_offload = NL80211_PROBE_RESP_OFFLOAD_SUPPORT_WPS | + NL80211_PROBE_RESP_OFFLOAD_SUPPORT_WPS2 | + NL80211_PROBE_RESP_OFFLOAD_SUPPORT_P2P | + NL80211_PROBE_RESP_OFFLOAD_SUPPORT_80211U; + hw->wiphy->flags |= WIPHY_FLAG_AP_PROBE_RESP_OFFLOAD; hw->wiphy->flags |= WIPHY_FLAG_AP_UAPSD; hw->wiphy->flags &= ~WIPHY_FLAG_PS_ON_BY_DEFAULT; hw->wiphy->max_ap_assoc_sta = WFX_MAX_STA_IN_AP_MODE; diff --git a/drivers/staging/wfx/queue.c b/drivers/staging/wfx/queue.c index 680fed31cefb..0bcc61feee1d 100644 --- a/drivers/staging/wfx/queue.c +++ b/drivers/staging/wfx/queue.c @@ -31,8 +31,6 @@ void wfx_tx_flush(struct wfx_dev *wdev) { int ret; - WARN(!atomic_read(&wdev->tx_lock), "tx_lock is not locked"); - // Do not wait for any reply if chip is frozen if (wdev->chip_frozen) return; @@ -177,11 +175,9 @@ void wfx_tx_queues_deinit(struct wfx_dev *wdev) wfx_tx_queues_clear(wdev); } -size_t wfx_tx_queue_get_num_queued(struct wfx_queue *queue, - u32 link_id_map) +int wfx_tx_queue_get_num_queued(struct wfx_queue *queue, u32 link_id_map) { - size_t ret; - int i, bit; + int ret, i; if (!link_id_map) return 0; @@ -191,11 +187,9 @@ size_t wfx_tx_queue_get_num_queued(struct wfx_queue *queue, ret = skb_queue_len(&queue->queue); } else { ret = 0; - for (i = 0, bit = 1; i < ARRAY_SIZE(queue->link_map_cache); - ++i, bit <<= 1) { - if (link_id_map & bit) + for (i = 0; i < ARRAY_SIZE(queue->link_map_cache); i++) + if (link_id_map & BIT(i)) ret += queue->link_map_cache[i]; - } } spin_unlock_bh(&queue->queue.lock); return ret; @@ -237,7 +231,6 @@ static struct sk_buff *wfx_tx_queue_get(struct wfx_dev *wdev, break; } } - WARN_ON(!skb); if (skb) { tx_priv = wfx_skb_tx_priv(skb); tx_priv->xmit_timestamp = ktime_get(); @@ -362,80 +355,38 @@ bool wfx_tx_queues_is_empty(struct wfx_dev *wdev) static bool hif_handle_tx_data(struct wfx_vif *wvif, struct sk_buff *skb, struct wfx_queue *queue) { - bool handled = false; - struct wfx_tx_priv *tx_priv = wfx_skb_tx_priv(skb); struct hif_req_tx *req = wfx_skb_txreq(skb); - struct ieee80211_hdr *frame = (struct ieee80211_hdr *) (req->frame + req->data_flags.fc_offset); - - enum { - do_probe, - do_drop, - do_wep, - do_tx, - } action = do_tx; - - switch (wvif->vif->type) { - case NL80211_IFTYPE_STATION: - if (wvif->state < WFX_STATE_PRE_STA) - action = do_drop; - break; - case NL80211_IFTYPE_AP: - if (!wvif->state) { - action = do_drop; - } else if (!(BIT(tx_priv->raw_link_id) & - (BIT(0) | wvif->link_id_map))) { - dev_warn(wvif->wdev->dev, "a frame with expired link-id is dropped\n"); - action = do_drop; - } - break; - case NL80211_IFTYPE_ADHOC: - if (wvif->state != WFX_STATE_IBSS) - action = do_drop; - break; - case NL80211_IFTYPE_MONITOR: - default: - action = do_drop; - break; - } - - if (action == do_tx) { - if (ieee80211_is_nullfunc(frame->frame_control)) { - mutex_lock(&wvif->bss_loss_lock); - if (wvif->bss_loss_state) { - wvif->bss_loss_confirm_id = req->packet_id; - req->queue_id.queue_id = HIF_QUEUE_ID_VOICE; - } - mutex_unlock(&wvif->bss_loss_lock); - } else if (ieee80211_has_protected(frame->frame_control) && - tx_priv->hw_key && - tx_priv->hw_key->keyidx != wvif->wep_default_key_id && - (tx_priv->hw_key->cipher == WLAN_CIPHER_SUITE_WEP40 || - tx_priv->hw_key->cipher == WLAN_CIPHER_SUITE_WEP104)) { - action = do_wep; + struct ieee80211_key_conf *hw_key = wfx_skb_tx_priv(skb)->hw_key; + struct ieee80211_hdr *frame = + (struct ieee80211_hdr *)(req->frame + req->data_flags.fc_offset); + + // FIXME: mac80211 is smart enough to handle BSS loss. Driver should not + // try to do anything about that. + if (ieee80211_is_nullfunc(frame->frame_control)) { + mutex_lock(&wvif->bss_loss_lock); + if (wvif->bss_loss_state) { + wvif->bss_loss_confirm_id = req->packet_id; + req->queue_id.queue_id = HIF_QUEUE_ID_VOICE; } + mutex_unlock(&wvif->bss_loss_lock); } - switch (action) { - case do_drop: - wfx_pending_remove(wvif->wdev, skb); - handled = true; - break; - case do_wep: + // FIXME: identify the exact scenario matched by this condition. Does it + // happen yet? + if (ieee80211_has_protected(frame->frame_control) && + hw_key && hw_key->keyidx != wvif->wep_default_key_id && + (hw_key->cipher == WLAN_CIPHER_SUITE_WEP40 || + hw_key->cipher == WLAN_CIPHER_SUITE_WEP104)) { wfx_tx_lock(wvif->wdev); WARN_ON(wvif->wep_pending_skb); - wvif->wep_default_key_id = tx_priv->hw_key->keyidx; + wvif->wep_default_key_id = hw_key->keyidx; wvif->wep_pending_skb = skb; if (!schedule_work(&wvif->wep_key_work)) wfx_tx_unlock(wvif->wdev); - handled = true; - break; - case do_tx: - break; - default: - /* Do nothing */ - break; + return true; + } else { + return false; } - return handled; } static int wfx_get_prio_queue(struct wfx_vif *wvif, @@ -443,7 +394,7 @@ static int wfx_get_prio_queue(struct wfx_vif *wvif, { static const int urgent = BIT(WFX_LINK_ID_AFTER_DTIM) | BIT(WFX_LINK_ID_UAPSD); - struct hif_req_edca_queue_params *edca; + const struct ieee80211_tx_queue_params *edca; unsigned int score, best = -1; int winner = -1; int i; @@ -452,13 +403,13 @@ static int wfx_get_prio_queue(struct wfx_vif *wvif, for (i = 0; i < IEEE80211_NUM_ACS; ++i) { int queued; - edca = &wvif->edca.params[i]; + edca = &wvif->edca_params[i]; queued = wfx_tx_queue_get_num_queued(&wvif->wdev->tx_queue[i], tx_allowed_mask); if (!queued) continue; *total += queued; - score = ((edca->aifsn + edca->cw_min) << 16) + + score = ((edca->aifs + edca->cw_min) << 16) + ((edca->cw_max - edca->cw_min) * (get_random_int() & 0xFFFF)); if (score < best && (winner < 0 || i != 3)) { @@ -480,94 +431,100 @@ static int wfx_get_prio_queue(struct wfx_vif *wvif, static int wfx_tx_queue_mask_get(struct wfx_vif *wvif, struct wfx_queue **queue_p, - u32 *tx_allowed_mask_p, - bool *more) + u32 *tx_allowed_mask_p) { int idx; u32 tx_allowed_mask; int total = 0; - /* Search for a queue with multicast frames buffered */ - if (wvif->mcast_tx) { - tx_allowed_mask = BIT(WFX_LINK_ID_AFTER_DTIM); - idx = wfx_get_prio_queue(wvif, tx_allowed_mask, &total); - if (idx >= 0) { - *more = total > 1; - goto found; - } - } - /* Search for unicast traffic */ tx_allowed_mask = ~wvif->sta_asleep_mask; tx_allowed_mask |= BIT(WFX_LINK_ID_UAPSD); - if (wvif->sta_asleep_mask) { - tx_allowed_mask |= wvif->pspoll_mask; + if (wvif->sta_asleep_mask) tx_allowed_mask &= ~BIT(WFX_LINK_ID_AFTER_DTIM); - } else { + else tx_allowed_mask |= BIT(WFX_LINK_ID_AFTER_DTIM); - } idx = wfx_get_prio_queue(wvif, tx_allowed_mask, &total); if (idx < 0) return -ENOENT; -found: *queue_p = &wvif->wdev->tx_queue[idx]; *tx_allowed_mask_p = tx_allowed_mask; return 0; } +struct hif_msg *wfx_tx_queues_get_after_dtim(struct wfx_vif *wvif) +{ + struct wfx_dev *wdev = wvif->wdev; + struct ieee80211_tx_info *tx_info; + struct hif_msg *hif; + struct sk_buff *skb; + int i; + + for (i = 0; i < IEEE80211_NUM_ACS; ++i) { + skb_queue_walk(&wdev->tx_queue[i].queue, skb) { + tx_info = IEEE80211_SKB_CB(skb); + hif = (struct hif_msg *)skb->data; + if ((tx_info->flags & IEEE80211_TX_CTL_SEND_AFTER_DTIM) && + (hif->interface == wvif->id)) + return (struct hif_msg *)skb->data; + } + } + return NULL; +} + struct hif_msg *wfx_tx_queues_get(struct wfx_dev *wdev) { struct sk_buff *skb; struct hif_msg *hif = NULL; - struct hif_req_tx *req = NULL; struct wfx_queue *queue = NULL; struct wfx_queue *vif_queue = NULL; u32 tx_allowed_mask = 0; u32 vif_tx_allowed_mask = 0; const struct wfx_tx_priv *tx_priv = NULL; struct wfx_vif *wvif; - /* More is used only for broadcasts. */ - bool more = false; - bool vif_more = false; int not_found; int burst; + int i; + + if (atomic_read(&wdev->tx_lock)) + return NULL; + + wvif = NULL; + while ((wvif = wvif_iterate(wdev, wvif)) != NULL) { + if (wvif->after_dtim_tx_allowed) { + for (i = 0; i < IEEE80211_NUM_ACS; ++i) { + skb = wfx_tx_queue_get(wvif->wdev, + &wdev->tx_queue[i], + BIT(WFX_LINK_ID_AFTER_DTIM)); + if (skb) { + hif = (struct hif_msg *)skb->data; + // Cannot happen since only one vif can + // be AP at time + WARN_ON(wvif->id != hif->interface); + return hif; + } + } + // No more multicast to sent + wvif->after_dtim_tx_allowed = false; + schedule_work(&wvif->update_tim_work); + } + } for (;;) { int ret = -ENOENT; int queue_num; - struct ieee80211_hdr *hdr; - - if (atomic_read(&wdev->tx_lock)) - return NULL; wvif = NULL; while ((wvif = wvif_iterate(wdev, wvif)) != NULL) { spin_lock_bh(&wvif->ps_state_lock); not_found = wfx_tx_queue_mask_get(wvif, &vif_queue, - &vif_tx_allowed_mask, - &vif_more); - - if (wvif->mcast_buffered && (not_found || !vif_more) && - (wvif->mcast_tx || - !wvif->sta_asleep_mask)) { - wvif->mcast_buffered = false; - if (wvif->mcast_tx) { - wvif->mcast_tx = false; - schedule_work(&wvif->mcast_stop_work); - } - } + &vif_tx_allowed_mask); spin_unlock_bh(&wvif->ps_state_lock); - if (vif_more) { - more = true; - tx_allowed_mask = vif_tx_allowed_mask; - queue = vif_queue; - ret = 0; - break; - } else if (!not_found) { + if (!not_found) { if (queue && queue != vif_queue) dev_info(wdev->dev, "vifs disagree about queue priority\n"); tx_allowed_mask |= vif_tx_allowed_mask; @@ -592,11 +549,9 @@ struct hif_msg *wfx_tx_queues_get(struct wfx_dev *wdev) if (hif_handle_tx_data(wvif, skb, queue)) continue; /* Handled by WSM */ - wvif->pspoll_mask &= ~BIT(tx_priv->raw_link_id); - /* allow bursting if txop is set */ - if (wvif->edca.params[queue_num].tx_op_limit) - burst = (int)wfx_tx_queue_get_num_queued(queue, tx_allowed_mask) + 1; + if (wvif->edca_params[queue_num].txop) + burst = wfx_tx_queue_get_num_queued(queue, tx_allowed_mask) + 1; else burst = 1; @@ -606,15 +561,6 @@ struct hif_msg *wfx_tx_queues_get(struct wfx_dev *wdev) else wdev->tx_burst_idx = -1; - /* more buffered multicast/broadcast frames - * ==> set MoreData flag in IEEE 802.11 header - * to inform PS STAs - */ - if (more) { - req = (struct hif_req_tx *) hif->body; - hdr = (struct ieee80211_hdr *) (req->frame + req->data_flags.fc_offset); - hdr->frame_control |= cpu_to_le16(IEEE80211_FCTL_MOREDATA); - } return hif; } } diff --git a/drivers/staging/wfx/queue.h b/drivers/staging/wfx/queue.h index 21566e48b2c2..90bb060d1204 100644 --- a/drivers/staging/wfx/queue.h +++ b/drivers/staging/wfx/queue.h @@ -13,9 +13,10 @@ #include "hif_api_cmd.h" #define WFX_MAX_STA_IN_AP_MODE 14 -#define WFX_LINK_ID_AFTER_DTIM (WFX_MAX_STA_IN_AP_MODE + 1) -#define WFX_LINK_ID_UAPSD (WFX_MAX_STA_IN_AP_MODE + 2) -#define WFX_LINK_ID_MAX (WFX_MAX_STA_IN_AP_MODE + 3) +#define WFX_LINK_ID_NO_ASSOC 15 +#define WFX_LINK_ID_AFTER_DTIM (WFX_LINK_ID_NO_ASSOC + 1) +#define WFX_LINK_ID_UAPSD (WFX_LINK_ID_NO_ASSOC + 2) +#define WFX_LINK_ID_MAX (WFX_LINK_ID_NO_ASSOC + 3) struct wfx_dev; struct wfx_vif; @@ -46,10 +47,11 @@ void wfx_tx_queues_clear(struct wfx_dev *wdev); bool wfx_tx_queues_is_empty(struct wfx_dev *wdev); void wfx_tx_queues_wait_empty_vif(struct wfx_vif *wvif); struct hif_msg *wfx_tx_queues_get(struct wfx_dev *wdev); +struct hif_msg *wfx_tx_queues_get_after_dtim(struct wfx_vif *wvif); void wfx_tx_queue_put(struct wfx_dev *wdev, struct wfx_queue *queue, struct sk_buff *skb); -size_t wfx_tx_queue_get_num_queued(struct wfx_queue *queue, u32 link_id_map); +int wfx_tx_queue_get_num_queued(struct wfx_queue *queue, u32 link_id_map); struct sk_buff *wfx_pending_get(struct wfx_dev *wdev, u32 packet_id); int wfx_pending_remove(struct wfx_dev *wdev, struct sk_buff *skb); diff --git a/drivers/staging/wfx/scan.c b/drivers/staging/wfx/scan.c index 35fcf9119f96..6e1e50048651 100644 --- a/drivers/staging/wfx/scan.c +++ b/drivers/staging/wfx/scan.c @@ -16,279 +16,118 @@ static void __ieee80211_scan_completed_compat(struct ieee80211_hw *hw, bool aborted) { struct cfg80211_scan_info info = { - .aborted = aborted ? 1 : 0, + .aborted = aborted, }; ieee80211_scan_completed(hw, &info); } -static void wfx_scan_restart_delayed(struct wfx_vif *wvif) +static int update_probe_tmpl(struct wfx_vif *wvif, + struct cfg80211_scan_request *req) { - if (wvif->delayed_unjoin) { - wvif->delayed_unjoin = false; - if (!schedule_work(&wvif->unjoin_work)) - wfx_tx_unlock(wvif->wdev); - } else if (wvif->delayed_link_loss) { - wvif->delayed_link_loss = 0; - wfx_cqm_bssloss_sm(wvif, 1, 0, 0); - } -} - -static int wfx_scan_start(struct wfx_vif *wvif, struct wfx_scan_params *scan) -{ - int ret; - int tmo = 500; - - if (wvif->state == WFX_STATE_PRE_STA) - return -EBUSY; - - tmo += scan->scan_req.num_of_channels * - ((20 * (scan->scan_req.max_channel_time)) + 10); - atomic_set(&wvif->scan.in_progress, 1); - atomic_set(&wvif->wdev->scan_in_progress, 1); - - schedule_delayed_work(&wvif->scan.timeout, msecs_to_jiffies(tmo)); - ret = hif_scan(wvif, scan); - if (ret) { - wfx_scan_failed_cb(wvif); - atomic_set(&wvif->scan.in_progress, 0); - atomic_set(&wvif->wdev->scan_in_progress, 0); - cancel_delayed_work_sync(&wvif->scan.timeout); - wfx_scan_restart_delayed(wvif); - } - return ret; -} - -int wfx_hw_scan(struct ieee80211_hw *hw, - struct ieee80211_vif *vif, - struct ieee80211_scan_request *hw_req) -{ - struct wfx_dev *wdev = hw->priv; - struct wfx_vif *wvif = (struct wfx_vif *) vif->drv_priv; - struct cfg80211_scan_request *req = &hw_req->req; struct sk_buff *skb; - int i, ret; - struct hif_mib_template_frame *p; - - if (!wvif) - return -EINVAL; - - if (wvif->state == WFX_STATE_AP) - return -EOPNOTSUPP; - - if (req->n_ssids == 1 && !req->ssids[0].ssid_len) - req->n_ssids = 0; - if (req->n_ssids > HIF_API_MAX_NB_SSIDS) - return -EINVAL; - - skb = ieee80211_probereq_get(hw, wvif->vif->addr, NULL, 0, req->ie_len); + skb = ieee80211_probereq_get(wvif->wdev->hw, wvif->vif->addr, + NULL, 0, req->ie_len); if (!skb) return -ENOMEM; - if (req->ie_len) - memcpy(skb_put(skb, req->ie_len), req->ie, req->ie_len); - - mutex_lock(&wdev->conf_mutex); - - p = (struct hif_mib_template_frame *)skb_push(skb, 4); - p->frame_type = HIF_TMPLT_PRBREQ; - p->frame_length = cpu_to_le16(skb->len - 4); - ret = hif_set_template_frame(wvif, p); - skb_pull(skb, 4); - - if (!ret) - /* Host want to be the probe responder. */ - ret = wfx_fwd_probe_req(wvif, true); - if (ret) { - mutex_unlock(&wdev->conf_mutex); - dev_kfree_skb(skb); - return ret; - } - - wfx_tx_lock_flush(wdev); - - WARN(wvif->scan.req, "unexpected concurrent scan"); - wvif->scan.req = req; - wvif->scan.n_ssids = 0; - wvif->scan.status = 0; - wvif->scan.begin = &req->channels[0]; - wvif->scan.curr = wvif->scan.begin; - wvif->scan.end = &req->channels[req->n_channels]; - wvif->scan.output_power = wdev->output_power; - - for (i = 0; i < req->n_ssids; ++i) { - struct hif_ssid_def *dst = &wvif->scan.ssids[wvif->scan.n_ssids]; - - memcpy(&dst->ssid[0], req->ssids[i].ssid, sizeof(dst->ssid)); - dst->ssid_length = req->ssids[i].ssid_len; - ++wvif->scan.n_ssids; - } - - mutex_unlock(&wdev->conf_mutex); - - if (skb) - dev_kfree_skb(skb); - schedule_work(&wvif->scan.work); + skb_put_data(skb, req->ie, req->ie_len); + hif_set_template_frame(wvif, skb, HIF_TMPLT_PRBREQ, 0); + dev_kfree_skb(skb); return 0; } -void wfx_scan_work(struct work_struct *work) +static int send_scan_req(struct wfx_vif *wvif, + struct cfg80211_scan_request *req, int start_idx) { - struct wfx_vif *wvif = container_of(work, struct wfx_vif, scan.work); - struct ieee80211_channel **it; - struct wfx_scan_params scan = { - .scan_req.scan_type.type = 0, /* Foreground */ - }; - struct ieee80211_channel *first; - bool first_run = (wvif->scan.begin == wvif->scan.curr && - wvif->scan.begin != wvif->scan.end); - int i; - - down(&wvif->scan.lock); - mutex_lock(&wvif->wdev->conf_mutex); - - if (first_run) { - if (wvif->state == WFX_STATE_STA && - !(wvif->powersave_mode.pm_mode.enter_psm)) { - struct hif_req_set_pm_mode pm = wvif->powersave_mode; - - pm.pm_mode.enter_psm = 1; - wfx_set_pm(wvif, &pm); - } - } - - if (!wvif->scan.req || wvif->scan.curr == wvif->scan.end) { - if (wvif->scan.output_power != wvif->wdev->output_power) - hif_set_output_power(wvif, - wvif->wdev->output_power * 10); - - if (wvif->scan.status < 0) - dev_warn(wvif->wdev->dev, "scan failed\n"); - else if (wvif->scan.req) - dev_dbg(wvif->wdev->dev, "scan completed\n"); - else - dev_dbg(wvif->wdev->dev, "scan canceled\n"); - - wvif->scan.req = NULL; - wfx_scan_restart_delayed(wvif); - wfx_tx_unlock(wvif->wdev); - mutex_unlock(&wvif->wdev->conf_mutex); - __ieee80211_scan_completed_compat(wvif->wdev->hw, - wvif->scan.status ? 1 : 0); - up(&wvif->scan.lock); - if (wvif->state == WFX_STATE_STA && - !(wvif->powersave_mode.pm_mode.enter_psm)) - wfx_set_pm(wvif, &wvif->powersave_mode); - return; - } - first = *wvif->scan.curr; - - for (it = wvif->scan.curr + 1, i = 1; - it != wvif->scan.end && i < HIF_API_MAX_NB_CHANNELS; - ++it, ++i) { - if ((*it)->band != first->band) - break; - if (((*it)->flags ^ first->flags) & - IEEE80211_CHAN_NO_IR) + int i, ret, timeout; + struct ieee80211_channel *ch_start, *ch_cur; + + for (i = start_idx; i < req->n_channels; i++) { + ch_start = req->channels[start_idx]; + ch_cur = req->channels[i]; + WARN(ch_cur->band != NL80211_BAND_2GHZ, "band not supported"); + if (ch_cur->max_power != ch_start->max_power) break; - if (!(first->flags & IEEE80211_CHAN_NO_IR) && - (*it)->max_power != first->max_power) + if ((ch_cur->flags ^ ch_start->flags) & IEEE80211_CHAN_NO_IR) break; } - scan.scan_req.band = first->band; - - if (wvif->scan.req->no_cck) - scan.scan_req.max_transmit_rate = API_RATE_INDEX_G_6MBPS; - else - scan.scan_req.max_transmit_rate = API_RATE_INDEX_B_1MBPS; - scan.scan_req.num_of_probe_requests = - (first->flags & IEEE80211_CHAN_NO_IR) ? 0 : 2; - scan.scan_req.num_of_ssi_ds = wvif->scan.n_ssids; - scan.ssids = &wvif->scan.ssids[0]; - scan.scan_req.num_of_channels = it - wvif->scan.curr; - scan.scan_req.probe_delay = 100; - // FIXME: Check if FW can do active scan while joined. - if (wvif->state == WFX_STATE_STA) { - scan.scan_req.scan_type.type = 1; - scan.scan_req.scan_flags.fbg = 1; + wfx_tx_lock_flush(wvif->wdev); + wvif->scan_abort = false; + reinit_completion(&wvif->scan_complete); + timeout = hif_scan(wvif, req, start_idx, i - start_idx); + if (timeout < 0) + return timeout; + ret = wait_for_completion_timeout(&wvif->scan_complete, timeout); + if (req->channels[start_idx]->max_power != wvif->vif->bss_conf.txpower) + hif_set_output_power(wvif, wvif->vif->bss_conf.txpower); + wfx_tx_unlock(wvif->wdev); + if (!ret) { + dev_notice(wvif->wdev->dev, "scan timeout\n"); + hif_stop_scan(wvif); + return -ETIMEDOUT; } - - scan.ch = kcalloc(scan.scan_req.num_of_channels, - sizeof(u8), GFP_KERNEL); - - if (!scan.ch) { - wvif->scan.status = -ENOMEM; - goto fail; + if (wvif->scan_abort) { + dev_notice(wvif->wdev->dev, "scan abort\n"); + return -ECONNABORTED; } - for (i = 0; i < scan.scan_req.num_of_channels; ++i) - scan.ch[i] = wvif->scan.curr[i]->hw_value; + return i - start_idx; +} - if (wvif->scan.curr[0]->flags & IEEE80211_CHAN_NO_IR) { - scan.scan_req.min_channel_time = 50; - scan.scan_req.max_channel_time = 150; - } else { - scan.scan_req.min_channel_time = 10; - scan.scan_req.max_channel_time = 50; - } - if (!(first->flags & IEEE80211_CHAN_NO_IR) && - wvif->scan.output_power != first->max_power) { - wvif->scan.output_power = first->max_power; - hif_set_output_power(wvif, wvif->scan.output_power * 10); - } - wvif->scan.status = wfx_scan_start(wvif, &scan); - kfree(scan.ch); - if (wvif->scan.status) - goto fail; - wvif->scan.curr = it; - mutex_unlock(&wvif->wdev->conf_mutex); - return; +/* + * It is not really necessary to run scan request asynchronously. However, + * there is a bug in "iw scan" when ieee80211_scan_completed() is called before + * wfx_hw_scan() return + */ +void wfx_hw_scan_work(struct work_struct *work) +{ + struct wfx_vif *wvif = container_of(work, struct wfx_vif, scan_work); + struct ieee80211_scan_request *hw_req = wvif->scan_req; + int chan_cur, ret; -fail: - wvif->scan.curr = wvif->scan.end; + mutex_lock(&wvif->scan_lock); + mutex_lock(&wvif->wdev->conf_mutex); + update_probe_tmpl(wvif, &hw_req->req); + wfx_fwd_probe_req(wvif, true); + chan_cur = 0; + do { + ret = send_scan_req(wvif, &hw_req->req, chan_cur); + if (ret > 0) + chan_cur += ret; + } while (ret > 0 && chan_cur < hw_req->req.n_channels); mutex_unlock(&wvif->wdev->conf_mutex); - up(&wvif->scan.lock); - schedule_work(&wvif->scan.work); + mutex_unlock(&wvif->scan_lock); + __ieee80211_scan_completed_compat(wvif->wdev->hw, ret < 0); } -static void wfx_scan_complete(struct wfx_vif *wvif) +int wfx_hw_scan(struct ieee80211_hw *hw, struct ieee80211_vif *vif, + struct ieee80211_scan_request *hw_req) { - up(&wvif->scan.lock); - atomic_set(&wvif->wdev->scan_in_progress, 0); + struct wfx_vif *wvif = (struct wfx_vif *)vif->drv_priv; - wfx_scan_work(&wvif->scan.work); -} + WARN_ON(hw_req->req.n_channels > HIF_API_MAX_NB_CHANNELS); -void wfx_scan_failed_cb(struct wfx_vif *wvif) -{ - if (cancel_delayed_work_sync(&wvif->scan.timeout) > 0) { - wvif->scan.status = -EIO; - schedule_work(&wvif->scan.timeout.work); - } + if (vif->type == NL80211_IFTYPE_AP) + return -EOPNOTSUPP; + + if (wvif->state == WFX_STATE_PRE_STA) + return -EBUSY; + + wvif->scan_req = hw_req; + schedule_work(&wvif->scan_work); + return 0; } -void wfx_scan_complete_cb(struct wfx_vif *wvif, struct hif_ind_scan_cmpl *arg) +void wfx_cancel_hw_scan(struct ieee80211_hw *hw, struct ieee80211_vif *vif) { - if (cancel_delayed_work_sync(&wvif->scan.timeout) > 0) { - wvif->scan.status = 1; - schedule_work(&wvif->scan.timeout.work); - } + struct wfx_vif *wvif = (struct wfx_vif *)vif->drv_priv; + + wvif->scan_abort = true; + hif_stop_scan(wvif); } -void wfx_scan_timeout(struct work_struct *work) +void wfx_scan_complete(struct wfx_vif *wvif) { - struct wfx_vif *wvif = container_of(work, struct wfx_vif, - scan.timeout.work); - - if (atomic_xchg(&wvif->scan.in_progress, 0)) { - if (wvif->scan.status > 0) { - wvif->scan.status = 0; - } else if (!wvif->scan.status) { - dev_warn(wvif->wdev->dev, "timeout waiting for scan complete notification\n"); - wvif->scan.status = -ETIMEDOUT; - wvif->scan.curr = wvif->scan.end; - hif_stop_scan(wvif); - } - wfx_scan_complete(wvif); - } + complete(&wvif->scan_complete); } diff --git a/drivers/staging/wfx/scan.h b/drivers/staging/wfx/scan.h index b4ddd0771a9b..2eb786c9572c 100644 --- a/drivers/staging/wfx/scan.h +++ b/drivers/staging/wfx/scan.h @@ -8,35 +8,15 @@ #ifndef WFX_SCAN_H #define WFX_SCAN_H -#include <linux/semaphore.h> -#include <linux/workqueue.h> #include <net/mac80211.h> -#include "hif_api_cmd.h" - struct wfx_dev; struct wfx_vif; -struct wfx_scan { - struct semaphore lock; - struct work_struct work; - struct delayed_work timeout; - struct cfg80211_scan_request *req; - struct ieee80211_channel **begin; - struct ieee80211_channel **curr; - struct ieee80211_channel **end; - struct hif_ssid_def ssids[HIF_API_MAX_NB_SSIDS]; - int output_power; - int n_ssids; - int status; - atomic_t in_progress; -}; - +void wfx_hw_scan_work(struct work_struct *work); int wfx_hw_scan(struct ieee80211_hw *hw, struct ieee80211_vif *vif, struct ieee80211_scan_request *req); -void wfx_scan_work(struct work_struct *work); -void wfx_scan_timeout(struct work_struct *work); -void wfx_scan_complete_cb(struct wfx_vif *wvif, struct hif_ind_scan_cmpl *arg); -void wfx_scan_failed_cb(struct wfx_vif *wvif); +void wfx_cancel_hw_scan(struct ieee80211_hw *hw, struct ieee80211_vif *vif); +void wfx_scan_complete(struct wfx_vif *wvif); #endif /* WFX_SCAN_H */ diff --git a/drivers/staging/wfx/secure_link.h b/drivers/staging/wfx/secure_link.h index 666b26e5308d..c3d055b2f8b1 100644 --- a/drivers/staging/wfx/secure_link.h +++ b/drivers/staging/wfx/secure_link.h @@ -25,14 +25,16 @@ static inline int wfx_sl_decode(struct wfx_dev *wdev, struct hif_sl_msg *m) return -EIO; } -static inline int wfx_sl_encode(struct wfx_dev *wdev, struct hif_msg *input, +static inline int wfx_sl_encode(struct wfx_dev *wdev, + const struct hif_msg *input, struct hif_sl_msg *output) { return -EIO; } -static inline int wfx_sl_check_pubkey(struct wfx_dev *wdev, u8 *ncp_pubkey, - u8 *ncp_pubmac) +static inline int wfx_sl_check_pubkey(struct wfx_dev *wdev, + const u8 *ncp_pubkey, + const u8 *ncp_pubmac) { return -EIO; } diff --git a/drivers/staging/wfx/sta.c b/drivers/staging/wfx/sta.c index 471dd15b227f..03d0f224ffdb 100644 --- a/drivers/staging/wfx/sta.c +++ b/drivers/staging/wfx/sta.c @@ -17,10 +17,9 @@ #include "hif_tx.h" #include "hif_tx_mib.h" -#define TXOP_UNIT 32 #define HIF_MAX_ARP_IP_ADDRTABLE_ENTRIES 2 -static u32 wfx_rate_mask_to_hw(struct wfx_dev *wdev, u32 rates) +u32 wfx_rate_mask_to_hw(struct wfx_dev *wdev, u32 rates) { int i; u32 ret = 0; @@ -64,13 +63,8 @@ void wfx_cqm_bssloss_sm(struct wfx_vif *wvif, int init, int good, int bad) int tx = 0; mutex_lock(&wvif->bss_loss_lock); - wvif->delayed_link_loss = 0; cancel_work_sync(&wvif->bss_params_work); - /* If we have a pending unjoin */ - if (wvif->delayed_unjoin) - goto end; - if (init) { schedule_delayed_work(&wvif->bss_loss_work, HZ); wvif->bss_loss_state = 0; @@ -94,62 +88,30 @@ void wfx_cqm_bssloss_sm(struct wfx_vif *wvif, int init, int good, int bad) // FIXME: call ieee80211_beacon_loss/ieee80211_connection_loss instead if (tx) { struct sk_buff *skb; + struct ieee80211_hdr *hdr; + struct ieee80211_tx_control control = { }; wvif->bss_loss_state++; skb = ieee80211_nullfunc_get(wvif->wdev->hw, wvif->vif, false); if (!skb) goto end; + hdr = (struct ieee80211_hdr *)skb->data; memset(IEEE80211_SKB_CB(skb), 0, sizeof(*IEEE80211_SKB_CB(skb))); IEEE80211_SKB_CB(skb)->control.vif = wvif->vif; IEEE80211_SKB_CB(skb)->driver_rates[0].idx = 0; IEEE80211_SKB_CB(skb)->driver_rates[0].count = 1; IEEE80211_SKB_CB(skb)->driver_rates[1].idx = -1; - wfx_tx(wvif->wdev->hw, NULL, skb); + rcu_read_lock(); // protect control.sta + control.sta = ieee80211_find_sta(wvif->vif, hdr->addr1); + wfx_tx(wvif->wdev->hw, &control, skb); + rcu_read_unlock(); } end: mutex_unlock(&wvif->bss_loss_lock); } -static int wfx_set_uapsd_param(struct wfx_vif *wvif, - const struct wfx_edca_params *arg) -{ - /* Here's the mapping AC [queue, bit] - * VO [0,3], VI [1, 2], BE [2, 1], BK [3, 0] - */ - - if (arg->uapsd_enable[IEEE80211_AC_VO]) - wvif->uapsd_info.trig_voice = 1; - else - wvif->uapsd_info.trig_voice = 0; - - if (arg->uapsd_enable[IEEE80211_AC_VI]) - wvif->uapsd_info.trig_video = 1; - else - wvif->uapsd_info.trig_video = 0; - - if (arg->uapsd_enable[IEEE80211_AC_BE]) - wvif->uapsd_info.trig_be = 1; - else - wvif->uapsd_info.trig_be = 0; - - if (arg->uapsd_enable[IEEE80211_AC_BK]) - wvif->uapsd_info.trig_bckgrnd = 1; - else - wvif->uapsd_info.trig_bckgrnd = 0; - - /* Currently pseudo U-APSD operation is not supported, so setting - * MinAutoTriggerInterval, MaxAutoTriggerInterval and - * AutoTriggerStep to 0 - */ - wvif->uapsd_info.min_auto_trigger_interval = 0; - wvif->uapsd_info.max_auto_trigger_interval = 0; - wvif->uapsd_info.auto_trigger_step = 0; - - return hif_set_uapsd_info(wvif, &wvif->uapsd_info); -} - int wfx_fwd_probe_req(struct wfx_vif *wvif, bool enable) { wvif->fwd_probe_req = enable; @@ -160,63 +122,31 @@ int wfx_fwd_probe_req(struct wfx_vif *wvif, bool enable) static int wfx_set_mcast_filter(struct wfx_vif *wvif, struct wfx_grp_addr_table *fp) { - int i, ret; - struct hif_mib_config_data_filter config = { }; - struct hif_mib_set_data_filtering filter_data = { }; - struct hif_mib_mac_addr_data_frame_condition filter_addr_val = { }; - struct hif_mib_uc_mc_bc_data_frame_condition filter_addr_type = { }; + int i; // Temporary workaround for filters - return hif_set_data_filtering(wvif, &filter_data); - - if (!fp->enable) { - filter_data.enable = 0; - return hif_set_data_filtering(wvif, &filter_data); - } - - // A1 Address match on list - for (i = 0; i < fp->num_addresses; i++) { - filter_addr_val.condition_idx = i; - filter_addr_val.address_type = HIF_MAC_ADDR_A1; - ether_addr_copy(filter_addr_val.mac_address, - fp->address_list[i]); - ret = hif_set_mac_addr_condition(wvif, - &filter_addr_val); - if (ret) - return ret; - config.mac_cond |= 1 << i; - } - - // Accept unicast and broadcast - filter_addr_type.condition_idx = 0; - filter_addr_type.param.bits.type_unicast = 1; - filter_addr_type.param.bits.type_broadcast = 1; - ret = hif_set_uc_mc_bc_condition(wvif, &filter_addr_type); - if (ret) - return ret; + return hif_set_data_filtering(wvif, false, true); - config.uc_mc_bc_cond = 1; - config.filter_idx = 0; // TODO #define MULTICAST_FILTERING 0 - config.enable = 1; - ret = hif_set_config_data_filter(wvif, &config); - if (ret) - return ret; + if (!fp->enable) + return hif_set_data_filtering(wvif, false, true); - // discard all data frames except match filter - filter_data.enable = 1; - filter_data.default_filter = 1; // discard all - ret = hif_set_data_filtering(wvif, &filter_data); + for (i = 0; i < fp->num_addresses; i++) + hif_set_mac_addr_condition(wvif, i, fp->address_list[i]); + hif_set_uc_mc_bc_condition(wvif, 0, + HIF_FILTER_UNICAST | HIF_FILTER_BROADCAST); + hif_set_config_data_filter(wvif, true, 0, BIT(1), + BIT(fp->num_addresses) - 1); + hif_set_data_filtering(wvif, true, true); - return ret; + return 0; } void wfx_update_filtering(struct wfx_vif *wvif) { int ret; - bool is_sta = wvif->vif && NL80211_IFTYPE_STATION == wvif->vif->type; - bool filter_bssid = wvif->filter_bssid; - bool fwd_probe_req = wvif->fwd_probe_req; - struct hif_mib_bcn_filter_enable bf_ctrl; + int bf_enable; + int bf_count; + int n_filter_ies; struct hif_ie_table_entry filter_ies[] = { { .ie_id = WLAN_EID_VENDOR_SPECIFIC, @@ -236,33 +166,29 @@ void wfx_update_filtering(struct wfx_vif *wvif) .has_appeared = 1, } }; - int n_filter_ies; if (wvif->state == WFX_STATE_PASSIVE) return; if (wvif->disable_beacon_filter) { - bf_ctrl.enable = 0; - bf_ctrl.bcn_count = 1; + bf_enable = 0; + bf_count = 1; n_filter_ies = 0; - } else if (!is_sta) { - bf_ctrl.enable = HIF_BEACON_FILTER_ENABLE | - HIF_BEACON_FILTER_AUTO_ERP; - bf_ctrl.bcn_count = 0; + } else if (wvif->vif->type != NL80211_IFTYPE_STATION) { + bf_enable = HIF_BEACON_FILTER_ENABLE | HIF_BEACON_FILTER_AUTO_ERP; + bf_count = 0; n_filter_ies = 2; } else { - bf_ctrl.enable = HIF_BEACON_FILTER_ENABLE; - bf_ctrl.bcn_count = 0; + bf_enable = HIF_BEACON_FILTER_ENABLE; + bf_count = 0; n_filter_ies = 3; } - ret = hif_set_rx_filter(wvif, filter_bssid, fwd_probe_req); + ret = hif_set_rx_filter(wvif, wvif->filter_bssid, wvif->fwd_probe_req); if (!ret) - ret = hif_set_beacon_filter_table(wvif, n_filter_ies, - filter_ies); + ret = hif_set_beacon_filter_table(wvif, n_filter_ies, filter_ies); if (!ret) - ret = hif_beacon_filter_control(wvif, bf_ctrl.enable, - bf_ctrl.bcn_count); + ret = hif_beacon_filter_control(wvif, bf_enable, bf_count); if (!ret) ret = wfx_set_mcast_filter(wvif, &wvif->mcast_filter); if (ret) @@ -316,90 +242,71 @@ void wfx_configure_filter(struct ieee80211_hw *hw, *total_flags &= FIF_OTHER_BSS | FIF_FCSFAIL | FIF_PROBE_REQ; while ((wvif = wvif_iterate(wdev, wvif)) != NULL) { - down(&wvif->scan.lock); + mutex_lock(&wvif->scan_lock); wvif->filter_bssid = (*total_flags & (FIF_OTHER_BSS | FIF_PROBE_REQ)) ? 0 : 1; wvif->disable_beacon_filter = !(*total_flags & FIF_PROBE_REQ); wfx_fwd_probe_req(wvif, true); wfx_update_filtering(wvif); - up(&wvif->scan.lock); + mutex_unlock(&wvif->scan_lock); } } -int wfx_conf_tx(struct ieee80211_hw *hw, struct ieee80211_vif *vif, - u16 queue, const struct ieee80211_tx_queue_params *params) +static int wfx_update_pm(struct wfx_vif *wvif) { - struct wfx_dev *wdev = hw->priv; - struct wfx_vif *wvif = (struct wfx_vif *) vif->drv_priv; - int ret = 0; - /* To prevent re-applying PM request OID again and again*/ - u16 old_uapsd_flags, new_uapsd_flags; - struct hif_req_edca_queue_params *edca; - - mutex_lock(&wdev->conf_mutex); + struct ieee80211_conf *conf = &wvif->wdev->hw->conf; + bool ps = conf->flags & IEEE80211_CONF_PS; + int ps_timeout = conf->dynamic_ps_timeout; + struct ieee80211_channel *chan0 = NULL, *chan1 = NULL; - if (queue < hw->queues) { - old_uapsd_flags = *((u16 *) &wvif->uapsd_info); - edca = &wvif->edca.params[queue]; - - wvif->edca.uapsd_enable[queue] = params->uapsd; - edca->aifsn = params->aifs; - edca->cw_min = params->cw_min; - edca->cw_max = params->cw_max; - edca->tx_op_limit = params->txop * TXOP_UNIT; - edca->allowed_medium_time = 0; - ret = hif_set_edca_queue_params(wvif, edca); - if (ret) { - ret = -EINVAL; - goto out; - } - - if (wvif->vif->type == NL80211_IFTYPE_STATION) { - ret = wfx_set_uapsd_param(wvif, &wvif->edca); - new_uapsd_flags = *((u16 *) &wvif->uapsd_info); - if (!ret && wvif->setbssparams_done && - wvif->state == WFX_STATE_STA && - old_uapsd_flags != new_uapsd_flags) - ret = wfx_set_pm(wvif, &wvif->powersave_mode); - } - } else { - ret = -EINVAL; + WARN_ON(conf->dynamic_ps_timeout < 0); + if (wvif->state != WFX_STATE_STA || !wvif->bss_params.aid) + return 0; + if (!ps) + ps_timeout = 0; + if (wvif->uapsd_mask) + ps_timeout = 0; + + // Kernel disable powersave when an AP is in use. In contrary, it is + // absolutely necessary to enable legacy powersave for WF200 if channels + // are differents. + if (wdev_to_wvif(wvif->wdev, 0)) + chan0 = wdev_to_wvif(wvif->wdev, 0)->vif->bss_conf.chandef.chan; + if (wdev_to_wvif(wvif->wdev, 1)) + chan1 = wdev_to_wvif(wvif->wdev, 1)->vif->bss_conf.chandef.chan; + if (chan0 && chan1 && chan0->hw_value != chan1->hw_value && + wvif->vif->type != NL80211_IFTYPE_AP) { + ps = true; + ps_timeout = 0; } -out: - mutex_unlock(&wdev->conf_mutex); - return ret; + if (!wait_for_completion_timeout(&wvif->set_pm_mode_complete, + TU_TO_JIFFIES(512))) + dev_warn(wvif->wdev->dev, + "timeout while waiting of set_pm_mode_complete\n"); + return hif_set_pm(wvif, ps, ps_timeout); } -int wfx_set_pm(struct wfx_vif *wvif, const struct hif_req_set_pm_mode *arg) +int wfx_conf_tx(struct ieee80211_hw *hw, struct ieee80211_vif *vif, + u16 queue, const struct ieee80211_tx_queue_params *params) { - struct hif_req_set_pm_mode pm = *arg; - u16 uapsd_flags; - int ret; - - if (wvif->state != WFX_STATE_STA || !wvif->bss_params.aid) - return 0; - - memcpy(&uapsd_flags, &wvif->uapsd_info, sizeof(uapsd_flags)); + struct wfx_dev *wdev = hw->priv; + struct wfx_vif *wvif = (struct wfx_vif *) vif->drv_priv; + int old_uapsd = wvif->uapsd_mask; + int ret = 0; - if (uapsd_flags != 0) - pm.pm_mode.fast_psm = 0; + WARN_ON(queue >= hw->queues); - // Kernel disable PowerSave when multiple vifs are in use. In contrary, - // it is absolutly necessary to enable PowerSave for WF200 - if (wvif_count(wvif->wdev) > 1) { - pm.pm_mode.enter_psm = 1; - pm.pm_mode.fast_psm = 0; + mutex_lock(&wdev->conf_mutex); + assign_bit(queue, &wvif->uapsd_mask, params->uapsd); + memcpy(&wvif->edca_params[queue], params, sizeof(*params)); + hif_set_edca_queue_params(wvif, queue, params); + if (wvif->vif->type == NL80211_IFTYPE_STATION && + old_uapsd != wvif->uapsd_mask) { + hif_set_uapsd_info(wvif, wvif->uapsd_mask); + wfx_update_pm(wvif); } - - if (!wait_for_completion_timeout(&wvif->set_pm_mode_complete, - msecs_to_jiffies(300))) - dev_warn(wvif->wdev->dev, - "timeout while waiting of set_pm_mode_complete\n"); - ret = hif_set_pm(wvif, &pm); - // FIXME: why ? - if (-ETIMEDOUT == wvif->scan.status) - wvif->scan.status = 1; + mutex_unlock(&wdev->conf_mutex); return ret; } @@ -413,56 +320,27 @@ int wfx_set_rts_threshold(struct ieee80211_hw *hw, u32 value) return 0; } -/* If successful, LOCKS the TX queue! */ static int __wfx_flush(struct wfx_dev *wdev, bool drop) { - int ret; - for (;;) { - if (drop) { + if (drop) wfx_tx_queues_clear(wdev); - } else { - ret = wait_event_timeout( - wdev->tx_queue_stats.wait_link_id_empty, - wfx_tx_queues_is_empty(wdev), - 2 * HZ); - } - - if (!drop && ret <= 0) { - ret = -ETIMEDOUT; - break; - } - ret = 0; - - wfx_tx_lock_flush(wdev); - if (!wfx_tx_queues_is_empty(wdev)) { - /* Highly unlikely: WSM requeued frames. */ - wfx_tx_unlock(wdev); - continue; - } - break; + if (wait_event_timeout(wdev->tx_queue_stats.wait_link_id_empty, + wfx_tx_queues_is_empty(wdev), + 2 * HZ) <= 0) + return -ETIMEDOUT; + wfx_tx_flush(wdev); + if (wfx_tx_queues_is_empty(wdev)) + return 0; + dev_warn(wdev->dev, "frames queued while flushing tx queues"); } - return ret; } void wfx_flush(struct ieee80211_hw *hw, struct ieee80211_vif *vif, u32 queues, bool drop) { - struct wfx_dev *wdev = hw->priv; - struct wfx_vif *wvif; - - if (vif) { - wvif = (struct wfx_vif *) vif->drv_priv; - if (wvif->vif->type == NL80211_IFTYPE_MONITOR) - drop = true; - if (wvif->vif->type == NL80211_IFTYPE_AP && - !wvif->enable_beacon) - drop = true; - } - - // FIXME: only flush requested vif - if (!__wfx_flush(wdev, drop)) - wfx_tx_unlock(wdev); + // FIXME: only flush requested vif and queues + __wfx_flush(hw->priv, drop); } /* WSM callbacks */ @@ -476,7 +354,7 @@ static void wfx_event_report_rssi(struct wfx_vif *wvif, u8 raw_rcpi_rssi) int cqm_evt; rcpi_rssi = raw_rcpi_rssi / 2 - 110; - if (rcpi_rssi <= wvif->cqm_rssi_thold) + if (rcpi_rssi <= wvif->vif->bss_conf.cqm_rssi_thold) cqm_evt = NL80211_CQM_RSSI_THRESHOLD_EVENT_LOW; else cqm_evt = NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH; @@ -499,18 +377,9 @@ static void wfx_event_handler_work(struct work_struct *work) switch (event->evt.event_id) { case HIF_EVENT_IND_BSSLOST: cancel_work_sync(&wvif->unjoin_work); - if (!down_trylock(&wvif->scan.lock)) { - wfx_cqm_bssloss_sm(wvif, 1, 0, 0); - up(&wvif->scan.lock); - } else { - /* Scan is in progress. Delay reporting. - * Scan complete will trigger bss_loss_work - */ - wvif->delayed_link_loss = 1; - /* Also start a watchdog. */ - schedule_delayed_work(&wvif->bss_loss_work, - 5 * HZ); - } + mutex_lock(&wvif->scan_lock); + wfx_cqm_bssloss_sm(wvif, 1, 0, 0); + mutex_unlock(&wvif->scan_lock); break; case HIF_EVENT_IND_BSSREGAINED: wfx_cqm_bssloss_sm(wvif, 0, 0, 0); @@ -554,30 +423,10 @@ static void wfx_bss_params_work(struct work_struct *work) mutex_unlock(&wvif->wdev->conf_mutex); } -static void wfx_set_beacon_wakeup_period_work(struct work_struct *work) -{ - struct wfx_vif *wvif = container_of(work, struct wfx_vif, - set_beacon_wakeup_period_work); - - hif_set_beacon_wakeup_period(wvif, wvif->dtim_period, - wvif->dtim_period); -} - static void wfx_do_unjoin(struct wfx_vif *wvif) { mutex_lock(&wvif->wdev->conf_mutex); - if (atomic_read(&wvif->scan.in_progress)) { - if (wvif->delayed_unjoin) - dev_dbg(wvif->wdev->dev, - "delayed unjoin is already scheduled\n"); - else - wvif->delayed_unjoin = true; - goto done; - } - - wvif->delayed_link_loss = false; - if (!wvif->state) goto done; @@ -585,7 +434,6 @@ static void wfx_do_unjoin(struct wfx_vif *wvif) goto done; cancel_work_sync(&wvif->update_filtering_work); - cancel_work_sync(&wvif->set_beacon_wakeup_period_work); wvif->state = WFX_STATE_PASSIVE; /* Unjoin is a reset. */ @@ -593,8 +441,6 @@ static void wfx_do_unjoin(struct wfx_vif *wvif) hif_keep_alive_period(wvif, 0); hif_reset(wvif, false); wfx_tx_policy_init(wvif); - hif_set_output_power(wvif, wvif->wdev->output_power * 10); - wvif->dtim_period = 0; hif_set_macaddr(wvif, wvif->vif->addr); wfx_free_event_queue(wvif); cancel_work_sync(&wvif->event_handler_work); @@ -606,8 +452,6 @@ static void wfx_do_unjoin(struct wfx_vif *wvif) wvif->disable_beacon_filter = false; wfx_update_filtering(wvif); memset(&wvif->bss_params, 0, sizeof(wvif->bss_params)); - wvif->setbssparams_done = false; - memset(&wvif->ht_info, 0, sizeof(wvif->ht_info)); done: mutex_unlock(&wvif->wdev->conf_mutex); @@ -644,33 +488,21 @@ static void wfx_set_mfp(struct wfx_vif *wvif, hif_set_mfp(wvif, mfpc, mfpr); } -/* MUST be called with tx_lock held! It will be unlocked for us. */ static void wfx_do_join(struct wfx_vif *wvif) { - const u8 *bssid; + int ret; + const u8 *ssidie; struct ieee80211_bss_conf *conf = &wvif->vif->bss_conf; struct cfg80211_bss *bss = NULL; - struct hif_req_join join = { - .mode = conf->ibss_joined ? HIF_MODE_IBSS : HIF_MODE_BSS, - .preamble_type = conf->use_short_preamble ? HIF_PREAMBLE_SHORT : HIF_PREAMBLE_LONG, - .probe_for_join = 1, - .atim_window = 0, - .basic_rate_set = wfx_rate_mask_to_hw(wvif->wdev, - conf->basic_rates), - }; - if (wvif->channel->flags & IEEE80211_CHAN_NO_IR) - join.probe_for_join = 0; + wfx_tx_lock_flush(wvif->wdev); if (wvif->state) wfx_do_unjoin(wvif); - bssid = wvif->vif->bss_conf.bssid; - bss = cfg80211_get_bss(wvif->wdev->hw->wiphy, wvif->channel, - bssid, NULL, 0, + conf->bssid, NULL, 0, IEEE80211_BSS_TYPE_ANY, IEEE80211_PRIVACY_ANY); - if (!bss && !conf->ibss_joined) { wfx_tx_unlock(wvif->wdev); return; @@ -678,41 +510,15 @@ static void wfx_do_join(struct wfx_vif *wvif) mutex_lock(&wvif->wdev->conf_mutex); - /* Under the conf lock: check scan status and - * bail out if it is in progress. - */ - if (atomic_read(&wvif->scan.in_progress)) { - wfx_tx_unlock(wvif->wdev); - goto done_put; - } - - /* Sanity check basic rates */ - if (!join.basic_rate_set) - join.basic_rate_set = 7; - /* Sanity check beacon interval */ if (!wvif->beacon_int) wvif->beacon_int = 1; - join.beacon_interval = wvif->beacon_int; - - // DTIM period will be set on first Beacon - wvif->dtim_period = 0; - - join.channel_number = wvif->channel->hw_value; - memcpy(join.bssid, bssid, sizeof(join.bssid)); - - if (!conf->ibss_joined) { - const u8 *ssidie; - - rcu_read_lock(); + rcu_read_lock(); + if (!conf->ibss_joined) ssidie = ieee80211_bss_get_ie(bss, WLAN_EID_SSID); - if (ssidie) { - join.ssid_length = ssidie[1]; - memcpy(join.ssid, &ssidie[2], join.ssid_length); - } - rcu_read_unlock(); - } + else + ssidie = NULL; wfx_tx_flush(wvif->wdev); @@ -723,7 +529,9 @@ static void wfx_do_join(struct wfx_vif *wvif) /* Perform actual join */ wvif->wdev->tx_burst_idx = -1; - if (hif_join(wvif, &join)) { + ret = hif_join(wvif, conf, wvif->channel, ssidie); + rcu_read_unlock(); + if (ret) { ieee80211_connection_loss(wvif->vif); wvif->join_complete_status = -1; /* Tx lock still held, unjoin will clear it. */ @@ -749,7 +557,6 @@ static void wfx_do_join(struct wfx_vif *wvif) } wfx_update_filtering(wvif); -done_put: mutex_unlock(&wvif->wdev->conf_mutex); if (bss) cfg80211_put_bss(wvif->wdev->hw->wiphy, bss); @@ -766,30 +573,26 @@ static void wfx_unjoin_work(struct work_struct *work) int wfx_sta_add(struct ieee80211_hw *hw, struct ieee80211_vif *vif, struct ieee80211_sta *sta) { - struct wfx_dev *wdev = hw->priv; struct wfx_vif *wvif = (struct wfx_vif *) vif->drv_priv; struct wfx_sta_priv *sta_priv = (struct wfx_sta_priv *) &sta->drv_priv; - struct wfx_link_entry *entry; - struct sk_buff *skb; - - if (wvif->vif->type != NL80211_IFTYPE_AP) - return 0; + spin_lock_init(&sta_priv->lock); sta_priv->vif_id = wvif->id; - sta_priv->link_id = wfx_find_link_id(wvif, sta->addr); - if (!sta_priv->link_id) { - dev_warn(wdev->dev, "mo more link-id available\n"); - return -ENOENT; - } - entry = &wvif->link_id_db[sta_priv->link_id - 1]; + // FIXME: in station mode, the current API interprets new link-id as a + // tdls peer. + if (vif->type == NL80211_IFTYPE_STATION) + return 0; + sta_priv->link_id = ffz(wvif->link_id_map); + wvif->link_id_map |= BIT(sta_priv->link_id); + WARN_ON(!sta_priv->link_id); + WARN_ON(sta_priv->link_id >= WFX_MAX_STA_IN_AP_MODE); + hif_map_link(wvif, sta->addr, 0, sta_priv->link_id); + spin_lock_bh(&wvif->ps_state_lock); if ((sta->uapsd_queues & IEEE80211_WMM_IE_STA_QOSINFO_AC_MASK) == IEEE80211_WMM_IE_STA_QOSINFO_AC_MASK) wvif->sta_asleep_mask |= BIT(sta_priv->link_id); - entry->status = WFX_LINK_HARD; - while ((skb = skb_dequeue(&entry->rx_queue))) - ieee80211_rx_irqsafe(wdev->hw, skb); spin_unlock_bh(&wvif->ps_state_lock); return 0; } @@ -797,225 +600,116 @@ int wfx_sta_add(struct ieee80211_hw *hw, struct ieee80211_vif *vif, int wfx_sta_remove(struct ieee80211_hw *hw, struct ieee80211_vif *vif, struct ieee80211_sta *sta) { - struct wfx_dev *wdev = hw->priv; struct wfx_vif *wvif = (struct wfx_vif *) vif->drv_priv; struct wfx_sta_priv *sta_priv = (struct wfx_sta_priv *) &sta->drv_priv; - struct wfx_link_entry *entry; + int i; - if (wvif->vif->type != NL80211_IFTYPE_AP || !sta_priv->link_id) + for (i = 0; i < ARRAY_SIZE(sta_priv->buffered); i++) + WARN(sta_priv->buffered[i], "release station while Tx is in progress"); + // FIXME: see note in wfx_sta_add() + if (vif->type == NL80211_IFTYPE_STATION) return 0; - - entry = &wvif->link_id_db[sta_priv->link_id - 1]; - spin_lock_bh(&wvif->ps_state_lock); - entry->status = WFX_LINK_RESERVE; - entry->timestamp = jiffies; - wfx_tx_lock(wdev); - if (!schedule_work(&wvif->link_id_work)) - wfx_tx_unlock(wdev); - spin_unlock_bh(&wvif->ps_state_lock); - flush_work(&wvif->link_id_work); + // FIXME add a mutex? + hif_map_link(wvif, sta->addr, 1, sta_priv->link_id); + wvif->link_id_map &= ~BIT(sta_priv->link_id); return 0; } -static void wfx_set_cts_work(struct work_struct *work) -{ - struct wfx_vif *wvif = container_of(work, struct wfx_vif, set_cts_work); - u8 erp_ie[3] = { WLAN_EID_ERP_INFO, 1, 0 }; - struct hif_ie_flags target_frame = { - .beacon = 1, - }; - - mutex_lock(&wvif->wdev->conf_mutex); - erp_ie[2] = wvif->erp_info; - mutex_unlock(&wvif->wdev->conf_mutex); - - hif_erp_use_protection(wvif, erp_ie[2] & WLAN_ERP_USE_PROTECTION); - - if (wvif->vif->type != NL80211_IFTYPE_STATION) - hif_update_ie(wvif, &target_frame, erp_ie, sizeof(erp_ie)); -} - static int wfx_start_ap(struct wfx_vif *wvif) { int ret; - struct ieee80211_bss_conf *conf = &wvif->vif->bss_conf; - struct hif_req_start start = { - .channel_number = wvif->channel->hw_value, - .beacon_interval = conf->beacon_int, - .dtim_period = conf->dtim_period, - .preamble_type = conf->use_short_preamble ? HIF_PREAMBLE_SHORT : HIF_PREAMBLE_LONG, - .basic_rate_set = wfx_rate_mask_to_hw(wvif->wdev, - conf->basic_rates), - }; - - memset(start.ssid, 0, sizeof(start.ssid)); - if (!conf->hidden_ssid) { - start.ssid_length = conf->ssid_len; - memcpy(start.ssid, conf->ssid, start.ssid_length); - } - - wvif->beacon_int = conf->beacon_int; - wvif->dtim_period = conf->dtim_period; - - memset(&wvif->link_id_db, 0, sizeof(wvif->link_id_db)); + wvif->beacon_int = wvif->vif->bss_conf.beacon_int; wvif->wdev->tx_burst_idx = -1; - ret = hif_start(wvif, &start); - if (!ret) - ret = wfx_upload_keys(wvif); - if (!ret) { - if (wvif_count(wvif->wdev) <= 1) - hif_set_block_ack_policy(wvif, 0xFF, 0xFF); - wvif->state = WFX_STATE_AP; - wfx_update_filtering(wvif); - } - return ret; + ret = hif_start(wvif, &wvif->vif->bss_conf, wvif->channel); + if (ret) + return ret; + ret = wfx_upload_keys(wvif); + if (ret) + return ret; + if (wvif_count(wvif->wdev) <= 1) + hif_set_block_ack_policy(wvif, 0xFF, 0xFF); + wvif->state = WFX_STATE_AP; + wfx_update_filtering(wvif); + return 0; } static int wfx_update_beaconing(struct wfx_vif *wvif) { - struct ieee80211_bss_conf *conf = &wvif->vif->bss_conf; - - if (wvif->vif->type == NL80211_IFTYPE_AP) { - /* TODO: check if changed channel, band */ - if (wvif->state != WFX_STATE_AP || - wvif->beacon_int != conf->beacon_int) { - wfx_tx_lock_flush(wvif->wdev); - if (wvif->state != WFX_STATE_PASSIVE) { - hif_reset(wvif, false); - wfx_tx_policy_init(wvif); - } - wvif->state = WFX_STATE_PASSIVE; - wfx_start_ap(wvif); - wfx_tx_unlock(wvif->wdev); - } else { - } - } + if (wvif->vif->type != NL80211_IFTYPE_AP) + return 0; + if (wvif->state == WFX_STATE_AP && + wvif->beacon_int == wvif->vif->bss_conf.beacon_int) + return 0; + wfx_tx_lock_flush(wvif->wdev); + hif_reset(wvif, false); + wfx_tx_policy_init(wvif); + wvif->state = WFX_STATE_PASSIVE; + wfx_start_ap(wvif); + wfx_tx_unlock(wvif->wdev); return 0; } -static int wfx_upload_beacon(struct wfx_vif *wvif) +static int wfx_upload_ap_templates(struct wfx_vif *wvif) { - int ret = 0; - struct sk_buff *skb = NULL; - struct ieee80211_mgmt *mgmt; - struct hif_mib_template_frame *p; + struct sk_buff *skb; if (wvif->vif->type == NL80211_IFTYPE_STATION || wvif->vif->type == NL80211_IFTYPE_MONITOR || wvif->vif->type == NL80211_IFTYPE_UNSPECIFIED) - goto done; + return 0; skb = ieee80211_beacon_get(wvif->wdev->hw, wvif->vif); - if (!skb) return -ENOMEM; - - p = (struct hif_mib_template_frame *) skb_push(skb, 4); - p->frame_type = HIF_TMPLT_BCN; - p->init_rate = API_RATE_INDEX_B_1MBPS; /* 1Mbps DSSS */ - p->frame_length = cpu_to_le16(skb->len - 4); - - ret = hif_set_template_frame(wvif, p); - - skb_pull(skb, 4); - - if (ret) - goto done; - /* TODO: Distill probe resp; remove TIM and any other beacon-specific - * IEs - */ - mgmt = (void *)skb->data; - mgmt->frame_control = - cpu_to_le16(IEEE80211_FTYPE_MGMT | IEEE80211_STYPE_PROBE_RESP); - - p->frame_type = HIF_TMPLT_PRBRES; - - ret = hif_set_template_frame(wvif, p); - wfx_fwd_probe_req(wvif, false); - -done: + hif_set_template_frame(wvif, skb, HIF_TMPLT_BCN, + API_RATE_INDEX_B_1MBPS); dev_kfree_skb(skb); - return ret; -} - -static int wfx_is_ht(const struct wfx_ht_info *ht_info) -{ - return ht_info->channel_type != NL80211_CHAN_NO_HT; -} - -static int wfx_ht_greenfield(const struct wfx_ht_info *ht_info) -{ - return wfx_is_ht(ht_info) && - (ht_info->ht_cap.cap & IEEE80211_HT_CAP_GRN_FLD) && - !(ht_info->operation_mode & - IEEE80211_HT_OP_MODE_NON_GF_STA_PRSNT); -} -static int wfx_ht_ampdu_density(const struct wfx_ht_info *ht_info) -{ - if (!wfx_is_ht(ht_info)) - return 0; - return ht_info->ht_cap.ampdu_density; + skb = ieee80211_proberesp_get(wvif->wdev->hw, wvif->vif); + if (!skb) + return -ENOMEM; + hif_set_template_frame(wvif, skb, HIF_TMPLT_PRBRES, + API_RATE_INDEX_B_1MBPS); + dev_kfree_skb(skb); + return 0; } static void wfx_join_finalize(struct wfx_vif *wvif, struct ieee80211_bss_conf *info) { struct ieee80211_sta *sta = NULL; - struct hif_mib_set_association_mode association_mode = { }; - if (info->dtim_period) - wvif->dtim_period = info->dtim_period; wvif->beacon_int = info->beacon_int; - - rcu_read_lock(); + rcu_read_lock(); // protect sta if (info->bssid && !info->ibss_joined) sta = ieee80211_find_sta(wvif->vif, info->bssid); - if (sta) { - wvif->ht_info.ht_cap = sta->ht_cap; + if (sta) wvif->bss_params.operational_rate_set = wfx_rate_mask_to_hw(wvif->wdev, sta->supp_rates[wvif->channel->band]); - wvif->ht_info.operation_mode = info->ht_operation_mode; - } else { - memset(&wvif->ht_info, 0, sizeof(wvif->ht_info)); + else wvif->bss_params.operational_rate_set = -1; - } - rcu_read_unlock(); - - /* Non Greenfield stations present */ - if (wvif->ht_info.operation_mode & - IEEE80211_HT_OP_MODE_NON_GF_STA_PRSNT) + if (sta && + info->ht_operation_mode & IEEE80211_HT_OP_MODE_NON_GF_STA_PRSNT) hif_dual_cts_protection(wvif, true); else hif_dual_cts_protection(wvif, false); - association_mode.preambtype_use = 1; - association_mode.mode = 1; - association_mode.rateset = 1; - association_mode.spacing = 1; - association_mode.preamble_type = info->use_short_preamble ? HIF_PREAMBLE_SHORT : HIF_PREAMBLE_LONG; - association_mode.basic_rate_set = cpu_to_le32(wfx_rate_mask_to_hw(wvif->wdev, info->basic_rates)); - association_mode.mixed_or_greenfield_type = wfx_ht_greenfield(&wvif->ht_info); - association_mode.mpdu_start_spacing = wfx_ht_ampdu_density(&wvif->ht_info); - wfx_cqm_bssloss_sm(wvif, 0, 0, 0); cancel_work_sync(&wvif->unjoin_work); wvif->bss_params.beacon_lost_count = 20; wvif->bss_params.aid = info->aid; - if (wvif->dtim_period < 1) - wvif->dtim_period = 1; - - hif_set_association_mode(wvif, &association_mode); + hif_set_association_mode(wvif, info, sta ? &sta->ht_cap : NULL); + rcu_read_unlock(); if (!info->ibss_joined) { hif_keep_alive_period(wvif, 30 /* sec */); hif_set_bss_params(wvif, &wvif->bss_params); - wvif->setbssparams_done = true; - wfx_set_beacon_wakeup_period_work(&wvif->set_beacon_wakeup_period_work); - wfx_set_pm(wvif, &wvif->powersave_mode); + hif_set_beacon_wakeup_period(wvif, info->dtim_period, + info->dtim_period); + wfx_update_pm(wvif); } } @@ -1028,48 +722,40 @@ void wfx_bss_info_changed(struct ieee80211_hw *hw, struct wfx_vif *wvif = (struct wfx_vif *) vif->drv_priv; bool do_join = false; int i; - int nb_arp_addr; mutex_lock(&wdev->conf_mutex); /* TODO: BSS_CHANGED_QOS */ if (changed & BSS_CHANGED_ARP_FILTER) { - struct hif_mib_arp_ip_addr_table filter = { }; - - nb_arp_addr = info->arp_addr_cnt; - if (nb_arp_addr <= 0 || nb_arp_addr > HIF_MAX_ARP_IP_ADDRTABLE_ENTRIES) - nb_arp_addr = 0; - for (i = 0; i < HIF_MAX_ARP_IP_ADDRTABLE_ENTRIES; i++) { - filter.condition_idx = i; - if (i < nb_arp_addr) { - // Caution: type of arp_addr_list[i] is __be32 - memcpy(filter.ipv4_address, - &info->arp_addr_list[i], - sizeof(filter.ipv4_address)); - filter.arp_enable = HIF_ARP_NS_FILTERING_ENABLE; - } else { - filter.arp_enable = HIF_ARP_NS_FILTERING_DISABLE; - } - hif_set_arp_ipv4_filter(wvif, &filter); + __be32 *arp_addr = &info->arp_addr_list[i]; + + if (info->arp_addr_cnt > HIF_MAX_ARP_IP_ADDRTABLE_ENTRIES) + arp_addr = NULL; + if (i >= info->arp_addr_cnt) + arp_addr = NULL; + hif_set_arp_ipv4_filter(wvif, i, arp_addr); } } - if (changed & - (BSS_CHANGED_BEACON | BSS_CHANGED_AP_PROBE_RESP | - BSS_CHANGED_BSSID | BSS_CHANGED_SSID | BSS_CHANGED_IBSS)) { + if (changed & BSS_CHANGED_BEACON || + changed & BSS_CHANGED_AP_PROBE_RESP || + changed & BSS_CHANGED_BSSID || + changed & BSS_CHANGED_SSID || + changed & BSS_CHANGED_IBSS) { wvif->beacon_int = info->beacon_int; wfx_update_beaconing(wvif); - wfx_upload_beacon(wvif); + wfx_upload_ap_templates(wvif); + wfx_fwd_probe_req(wvif, false); } if (changed & BSS_CHANGED_BEACON_ENABLED && - wvif->state != WFX_STATE_IBSS) { - if (wvif->enable_beacon != info->enable_beacon) { - hif_beacon_transmit(wvif, info->enable_beacon); - wvif->enable_beacon = info->enable_beacon; - } - } + wvif->state != WFX_STATE_IBSS) + hif_beacon_transmit(wvif, info->enable_beacon); + + if (changed & BSS_CHANGED_BEACON_INFO) + hif_set_beacon_wakeup_period(wvif, info->dtim_period, + info->dtim_period); /* assoc/disassoc, or maybe AID changed */ if (changed & BSS_CHANGED_ASSOC) { @@ -1095,10 +781,11 @@ void wfx_bss_info_changed(struct ieee80211_hw *hw, if (changed & BSS_CHANGED_BSSID) do_join = true; - if (changed & - (BSS_CHANGED_ASSOC | BSS_CHANGED_BSSID | - BSS_CHANGED_IBSS | BSS_CHANGED_BASIC_RATES | - BSS_CHANGED_HT)) { + if (changed & BSS_CHANGED_ASSOC || + changed & BSS_CHANGED_BSSID || + changed & BSS_CHANGED_IBSS || + changed & BSS_CHANGED_BASIC_RATES || + changed & BSS_CHANGED_HT) { if (info->assoc) { if (wvif->state < WFX_STATE_PRE_STA) { ieee80211_connection_loss(vif); @@ -1119,106 +806,50 @@ void wfx_bss_info_changed(struct ieee80211_hw *hw, } } - /* ERP Protection */ - if (changed & (BSS_CHANGED_ASSOC | - BSS_CHANGED_ERP_CTS_PROT | - BSS_CHANGED_ERP_PREAMBLE)) { - u32 prev_erp_info = wvif->erp_info; + if (changed & BSS_CHANGED_ASSOC || + changed & BSS_CHANGED_ERP_CTS_PROT || + changed & BSS_CHANGED_ERP_PREAMBLE) { + u8 erp_ie[3] = { WLAN_EID_ERP_INFO, 1, 0 }; + hif_erp_use_protection(wvif, info->use_cts_prot); if (info->use_cts_prot) - wvif->erp_info |= WLAN_ERP_USE_PROTECTION; - else if (!(prev_erp_info & WLAN_ERP_NON_ERP_PRESENT)) - wvif->erp_info &= ~WLAN_ERP_USE_PROTECTION; - + erp_ie[2] |= WLAN_ERP_USE_PROTECTION; if (info->use_short_preamble) - wvif->erp_info |= WLAN_ERP_BARKER_PREAMBLE; - else - wvif->erp_info &= ~WLAN_ERP_BARKER_PREAMBLE; - - if (prev_erp_info != wvif->erp_info) - schedule_work(&wvif->set_cts_work); + erp_ie[2] |= WLAN_ERP_BARKER_PREAMBLE; + if (wvif->vif->type != NL80211_IFTYPE_STATION) + hif_update_ie_beacon(wvif, erp_ie, sizeof(erp_ie)); } - if (changed & (BSS_CHANGED_ASSOC | BSS_CHANGED_ERP_SLOT)) + if (changed & BSS_CHANGED_ASSOC || changed & BSS_CHANGED_ERP_SLOT) hif_slot_time(wvif, info->use_short_slot ? 9 : 20); - if (changed & (BSS_CHANGED_ASSOC | BSS_CHANGED_CQM)) { - struct hif_mib_rcpi_rssi_threshold th = { - .rolling_average_count = 8, - .detection = 1, - }; - - wvif->cqm_rssi_thold = info->cqm_rssi_thold; - - if (!info->cqm_rssi_thold && !info->cqm_rssi_hyst) { - th.upperthresh = 1; - th.lowerthresh = 1; - } else { - /* FIXME It's not a correct way of setting threshold. - * Upper and lower must be set equal here and adjusted - * in callback. However current implementation is much - * more reliable and stable. - */ - /* RSSI: signed Q8.0, RCPI: unsigned Q7.1 - * RSSI = RCPI / 2 - 110 - */ - th.upper_threshold = info->cqm_rssi_thold + info->cqm_rssi_hyst; - th.upper_threshold = (th.upper_threshold + 110) * 2; - th.lower_threshold = info->cqm_rssi_thold; - th.lower_threshold = (th.lower_threshold + 110) * 2; - } - hif_set_rcpi_rssi_threshold(wvif, &th); - } + if (changed & BSS_CHANGED_ASSOC || changed & BSS_CHANGED_CQM) + hif_set_rcpi_rssi_threshold(wvif, info->cqm_rssi_thold, + info->cqm_rssi_hyst); + + if (changed & BSS_CHANGED_TXPOWER) + hif_set_output_power(wvif, info->txpower); + + if (changed & BSS_CHANGED_PS) + wfx_update_pm(wvif); - if (changed & BSS_CHANGED_TXPOWER && - info->txpower != wdev->output_power) { - wdev->output_power = info->txpower; - hif_set_output_power(wvif, wdev->output_power * 10); - } mutex_unlock(&wdev->conf_mutex); - if (do_join) { - wfx_tx_lock_flush(wdev); - wfx_do_join(wvif); /* Will unlock it for us */ - } + if (do_join) + wfx_do_join(wvif); } -static void wfx_ps_notify(struct wfx_vif *wvif, enum sta_notify_cmd notify_cmd, - int link_id) +static void wfx_ps_notify_sta(struct wfx_vif *wvif, + enum sta_notify_cmd notify_cmd, int link_id) { - u32 bit, prev; - spin_lock_bh(&wvif->ps_state_lock); - /* Zero link id means "for all link IDs" */ - if (link_id) { - bit = BIT(link_id); - } else if (notify_cmd != STA_NOTIFY_AWAKE) { - dev_warn(wvif->wdev->dev, "unsupported notify command\n"); - bit = 0; - } else { - bit = wvif->link_id_map; - } - prev = wvif->sta_asleep_mask & bit; - - switch (notify_cmd) { - case STA_NOTIFY_SLEEP: - if (!prev) { - if (wvif->mcast_buffered && !wvif->sta_asleep_mask) - schedule_work(&wvif->mcast_start_work); - wvif->sta_asleep_mask |= bit; - } - break; - case STA_NOTIFY_AWAKE: - if (prev) { - wvif->sta_asleep_mask &= ~bit; - wvif->pspoll_mask &= ~bit; - if (link_id && !wvif->sta_asleep_mask) - schedule_work(&wvif->mcast_stop_work); - wfx_bh_request_tx(wvif->wdev); - } - break; - } + if (notify_cmd == STA_NOTIFY_SLEEP) + wvif->sta_asleep_mask |= BIT(link_id); + else // notify_cmd == STA_NOTIFY_AWAKE + wvif->sta_asleep_mask &= ~BIT(link_id); spin_unlock_bh(&wvif->ps_state_lock); + if (notify_cmd == STA_NOTIFY_AWAKE) + wfx_bh_request_tx(wvif->wdev); } void wfx_sta_notify(struct ieee80211_hw *hw, struct ieee80211_vif *vif, @@ -1227,23 +858,19 @@ void wfx_sta_notify(struct ieee80211_hw *hw, struct ieee80211_vif *vif, struct wfx_vif *wvif = (struct wfx_vif *) vif->drv_priv; struct wfx_sta_priv *sta_priv = (struct wfx_sta_priv *) &sta->drv_priv; - wfx_ps_notify(wvif, notify_cmd, sta_priv->link_id); + wfx_ps_notify_sta(wvif, notify_cmd, sta_priv->link_id); } -static int wfx_set_tim_impl(struct wfx_vif *wvif, bool aid0_bit_set) +static int wfx_update_tim(struct wfx_vif *wvif) { struct sk_buff *skb; - struct hif_ie_flags target_frame = { - .beacon = 1, - }; u16 tim_offset, tim_length; u8 *tim_ptr; skb = ieee80211_beacon_get_tim(wvif->wdev->hw, wvif->vif, &tim_offset, &tim_length); if (!skb) { - if (!__wfx_flush(wvif->wdev, true)) - wfx_tx_unlock(wvif->wdev); + __wfx_flush(wvif->wdev, true); return -ENOENT; } tim_ptr = skb->data + tim_offset; @@ -1255,23 +882,23 @@ static int wfx_set_tim_impl(struct wfx_vif *wvif, bool aid0_bit_set) tim_ptr[2] = 0; /* Set/reset aid0 bit */ - if (aid0_bit_set) + if (wfx_tx_queues_get_after_dtim(wvif)) tim_ptr[4] |= 1; else tim_ptr[4] &= ~1; } - hif_update_ie(wvif, &target_frame, tim_ptr, tim_length); + hif_update_ie_beacon(wvif, tim_ptr, tim_length); dev_kfree_skb(skb); return 0; } -static void wfx_set_tim_work(struct work_struct *work) +static void wfx_update_tim_work(struct work_struct *work) { - struct wfx_vif *wvif = container_of(work, struct wfx_vif, set_tim_work); + struct wfx_vif *wvif = container_of(work, struct wfx_vif, update_tim_work); - wfx_set_tim_impl(wvif, wvif->aid0_bit_set); + wfx_update_tim(wvif); } int wfx_set_tim(struct ieee80211_hw *hw, struct ieee80211_sta *sta, bool set) @@ -1280,50 +907,16 @@ int wfx_set_tim(struct ieee80211_hw *hw, struct ieee80211_sta *sta, bool set) struct wfx_sta_priv *sta_dev = (struct wfx_sta_priv *) &sta->drv_priv; struct wfx_vif *wvif = wdev_to_wvif(wdev, sta_dev->vif_id); - schedule_work(&wvif->set_tim_work); + schedule_work(&wvif->update_tim_work); return 0; } -static void wfx_mcast_start_work(struct work_struct *work) +void wfx_suspend_resume_mc(struct wfx_vif *wvif, enum sta_notify_cmd notify_cmd) { - struct wfx_vif *wvif = container_of(work, struct wfx_vif, - mcast_start_work); - long tmo = wvif->dtim_period * TU_TO_JIFFIES(wvif->beacon_int + 20); - - cancel_work_sync(&wvif->mcast_stop_work); - if (!wvif->aid0_bit_set) { - wfx_tx_lock_flush(wvif->wdev); - wfx_set_tim_impl(wvif, true); - wvif->aid0_bit_set = true; - mod_timer(&wvif->mcast_timeout, jiffies + tmo); - wfx_tx_unlock(wvif->wdev); - } -} - -static void wfx_mcast_stop_work(struct work_struct *work) -{ - struct wfx_vif *wvif = container_of(work, struct wfx_vif, - mcast_stop_work); - - if (wvif->aid0_bit_set) { - del_timer_sync(&wvif->mcast_timeout); - wfx_tx_lock_flush(wvif->wdev); - wvif->aid0_bit_set = false; - wfx_set_tim_impl(wvif, false); - wfx_tx_unlock(wvif->wdev); - } -} - -static void wfx_mcast_timeout(struct timer_list *t) -{ - struct wfx_vif *wvif = from_timer(wvif, t, mcast_timeout); - - dev_warn(wvif->wdev->dev, "multicast delivery timeout\n"); - spin_lock_bh(&wvif->ps_state_lock); - wvif->mcast_tx = wvif->aid0_bit_set && wvif->mcast_buffered; - if (wvif->mcast_tx) - wfx_bh_request_tx(wvif->wdev); - spin_unlock_bh(&wvif->ps_state_lock); + WARN(!wfx_tx_queues_get_after_dtim(wvif), "incorrect sequence"); + WARN(wvif->after_dtim_tx_allowed, "incorrect sequence"); + wvif->after_dtim_tx_allowed = true; + wfx_bh_request_tx(wvif->wdev); } int wfx_ampdu_action(struct ieee80211_hw *hw, @@ -1341,35 +934,6 @@ int wfx_ampdu_action(struct ieee80211_hw *hw, return -ENOTSUPP; } -void wfx_suspend_resume(struct wfx_vif *wvif, - struct hif_ind_suspend_resume_tx *arg) -{ - if (arg->suspend_resume_flags.bc_mc_only) { - bool cancel_tmo = false; - - spin_lock_bh(&wvif->ps_state_lock); - if (!arg->suspend_resume_flags.resume) - wvif->mcast_tx = false; - else - wvif->mcast_tx = wvif->aid0_bit_set && - wvif->mcast_buffered; - if (wvif->mcast_tx) { - cancel_tmo = true; - wfx_bh_request_tx(wvif->wdev); - } - spin_unlock_bh(&wvif->ps_state_lock); - if (cancel_tmo) - del_timer_sync(&wvif->mcast_timeout); - } else if (arg->suspend_resume_flags.resume) { - // FIXME: should change each station status independently - wfx_ps_notify(wvif, STA_NOTIFY_AWAKE, 0); - wfx_bh_request_tx(wvif->wdev); - } else { - // FIXME: should change each station status independently - wfx_ps_notify(wvif, STA_NOTIFY_SLEEP, 0); - } -} - int wfx_add_chanctx(struct ieee80211_hw *hw, struct ieee80211_chanctx_conf *conf) { @@ -1395,7 +959,6 @@ int wfx_assign_vif_chanctx(struct ieee80211_hw *hw, struct ieee80211_vif *vif, WARN(wvif->channel, "channel overwrite"); wvif->channel = ch; - wvif->ht_info.channel_type = cfg80211_get_chandef_type(&conf->def); return 0; } @@ -1413,97 +976,14 @@ void wfx_unassign_vif_chanctx(struct ieee80211_hw *hw, int wfx_config(struct ieee80211_hw *hw, u32 changed) { - int ret = 0; - struct wfx_dev *wdev = hw->priv; - struct ieee80211_conf *conf = &hw->conf; - struct wfx_vif *wvif; - - // FIXME: Interface id should not been hardcoded - wvif = wdev_to_wvif(wdev, 0); - if (!wvif) { - WARN(1, "interface 0 does not exist anymore"); - return 0; - } - - down(&wvif->scan.lock); - mutex_lock(&wdev->conf_mutex); - if (changed & IEEE80211_CONF_CHANGE_POWER) { - wdev->output_power = conf->power_level; - hif_set_output_power(wvif, wdev->output_power * 10); - } - - if (changed & IEEE80211_CONF_CHANGE_PS) { - wvif = NULL; - while ((wvif = wvif_iterate(wdev, wvif)) != NULL) { - memset(&wvif->powersave_mode, 0, - sizeof(wvif->powersave_mode)); - if (conf->flags & IEEE80211_CONF_PS) { - wvif->powersave_mode.pm_mode.enter_psm = 1; - if (conf->dynamic_ps_timeout > 0) { - wvif->powersave_mode.pm_mode.fast_psm = 1; - /* - * Firmware does not support more than - * 128ms - */ - wvif->powersave_mode.fast_psm_idle_period = - min(conf->dynamic_ps_timeout * - 2, 255); - } - } - if (wvif->state == WFX_STATE_STA && wvif->bss_params.aid) - wfx_set_pm(wvif, &wvif->powersave_mode); - } - wvif = wdev_to_wvif(wdev, 0); - } - - mutex_unlock(&wdev->conf_mutex); - up(&wvif->scan.lock); - return ret; + return 0; } int wfx_add_interface(struct ieee80211_hw *hw, struct ieee80211_vif *vif) { - int i; + int i, ret = 0; struct wfx_dev *wdev = hw->priv; struct wfx_vif *wvif = (struct wfx_vif *) vif->drv_priv; - // FIXME: parameters are set by kernel juste after interface_add. - // Keep struct hif_req_edca_queue_params blank? - struct hif_req_edca_queue_params default_edca_params[] = { - [IEEE80211_AC_VO] = { - .queue_id = HIF_QUEUE_ID_VOICE, - .aifsn = 2, - .cw_min = 3, - .cw_max = 7, - .tx_op_limit = TXOP_UNIT * 47, - }, - [IEEE80211_AC_VI] = { - .queue_id = HIF_QUEUE_ID_VIDEO, - .aifsn = 2, - .cw_min = 7, - .cw_max = 15, - .tx_op_limit = TXOP_UNIT * 94, - }, - [IEEE80211_AC_BE] = { - .queue_id = HIF_QUEUE_ID_BESTEFFORT, - .aifsn = 3, - .cw_min = 15, - .cw_max = 1023, - .tx_op_limit = TXOP_UNIT * 0, - }, - [IEEE80211_AC_BK] = { - .queue_id = HIF_QUEUE_ID_BACKGROUND, - .aifsn = 7, - .cw_min = 15, - .cw_max = 1023, - .tx_op_limit = TXOP_UNIT * 0, - }, - }; - - BUILD_BUG_ON(ARRAY_SIZE(default_edca_params) != ARRAY_SIZE(wvif->edca.params)); - if (wfx_api_older_than(wdev, 2, 0)) { - default_edca_params[IEEE80211_AC_BE].queue_id = HIF_QUEUE_ID_BACKGROUND; - default_edca_params[IEEE80211_AC_BK].queue_id = HIF_QUEUE_ID_BESTEFFORT; - } vif->driver_flags |= IEEE80211_VIF_BEACON_FILTER | IEEE80211_VIF_SUPPORTS_UAPSD | @@ -1536,51 +1016,37 @@ int wfx_add_interface(struct ieee80211_hw *hw, struct ieee80211_vif *vif) wvif->vif = vif; wvif->wdev = wdev; - INIT_WORK(&wvif->link_id_work, wfx_link_id_work); - INIT_DELAYED_WORK(&wvif->link_id_gc_work, wfx_link_id_gc_work); - + wvif->link_id_map = 1; // link-id 0 is reserved for multicast spin_lock_init(&wvif->ps_state_lock); - INIT_WORK(&wvif->set_tim_work, wfx_set_tim_work); + INIT_WORK(&wvif->update_tim_work, wfx_update_tim_work); - INIT_WORK(&wvif->mcast_start_work, wfx_mcast_start_work); - INIT_WORK(&wvif->mcast_stop_work, wfx_mcast_stop_work); - timer_setup(&wvif->mcast_timeout, wfx_mcast_timeout, 0); + memset(&wvif->bss_params, 0, sizeof(wvif->bss_params)); - wvif->setbssparams_done = false; mutex_init(&wvif->bss_loss_lock); INIT_DELAYED_WORK(&wvif->bss_loss_work, wfx_bss_loss_work); wvif->wep_default_key_id = -1; INIT_WORK(&wvif->wep_key_work, wfx_wep_key_work); - sema_init(&wvif->scan.lock, 1); - INIT_WORK(&wvif->scan.work, wfx_scan_work); - INIT_DELAYED_WORK(&wvif->scan.timeout, wfx_scan_timeout); - spin_lock_init(&wvif->event_queue_lock); INIT_LIST_HEAD(&wvif->event_queue); INIT_WORK(&wvif->event_handler_work, wfx_event_handler_work); init_completion(&wvif->set_pm_mode_complete); complete(&wvif->set_pm_mode_complete); - INIT_WORK(&wvif->set_beacon_wakeup_period_work, - wfx_set_beacon_wakeup_period_work); INIT_WORK(&wvif->update_filtering_work, wfx_update_filtering_work); INIT_WORK(&wvif->bss_params_work, wfx_bss_params_work); - INIT_WORK(&wvif->set_cts_work, wfx_set_cts_work); INIT_WORK(&wvif->unjoin_work, wfx_unjoin_work); + INIT_WORK(&wvif->tx_policy_upload_work, wfx_tx_policy_upload_work); + + mutex_init(&wvif->scan_lock); + init_completion(&wvif->scan_complete); + INIT_WORK(&wvif->scan_work, wfx_hw_scan_work); INIT_WORK(&wvif->tx_policy_upload_work, wfx_tx_policy_upload_work); mutex_unlock(&wdev->conf_mutex); hif_set_macaddr(wvif, vif->addr); - for (i = 0; i < IEEE80211_NUM_ACS; i++) { - memcpy(&wvif->edca.params[i], &default_edca_params[i], - sizeof(default_edca_params[i])); - wvif->edca.uapsd_enable[i] = false; - hif_set_edca_queue_params(wvif, &wvif->edca.params[i]); - } - wfx_set_uapsd_param(wvif, &wvif->edca); wfx_tx_policy_init(wvif); wvif = NULL; @@ -1591,9 +1057,9 @@ int wfx_add_interface(struct ieee80211_hw *hw, struct ieee80211_vif *vif) else hif_set_block_ack_policy(wvif, 0x00, 0x00); // Combo force powersave mode. We can re-enable it now - wfx_set_pm(wvif, &wvif->powersave_mode); + ret = wfx_update_pm(wvif); } - return 0; + return ret; } void wfx_remove_interface(struct ieee80211_hw *hw, @@ -1601,15 +1067,11 @@ void wfx_remove_interface(struct ieee80211_hw *hw, { struct wfx_dev *wdev = hw->priv; struct wfx_vif *wvif = (struct wfx_vif *) vif->drv_priv; - int i; - // If scan is in progress, stop it - while (down_trylock(&wvif->scan.lock)) - schedule(); - up(&wvif->scan.lock); wait_for_completion_timeout(&wvif->set_pm_mode_complete, msecs_to_jiffies(300)); mutex_lock(&wdev->conf_mutex); + WARN(wvif->link_id_map != 1, "corrupted state"); switch (wvif->state) { case WFX_STATE_PRE_STA: case WFX_STATE_STA: @@ -1619,19 +1081,7 @@ void wfx_remove_interface(struct ieee80211_hw *hw, wfx_tx_unlock(wdev); break; case WFX_STATE_AP: - for (i = 0; wvif->link_id_map; ++i) { - if (wvif->link_id_map & BIT(i)) { - wfx_unmap_link(wvif, i); - wvif->link_id_map &= ~BIT(i); - } - } - memset(wvif->link_id_db, 0, sizeof(wvif->link_id_db)); wvif->sta_asleep_mask = 0; - wvif->enable_beacon = false; - wvif->mcast_tx = false; - wvif->aid0_bit_set = false; - wvif->mcast_buffered = false; - wvif->pspoll_mask = 0; /* reset.link_id = 0; */ hif_reset(wvif, false); break; @@ -1646,12 +1096,8 @@ void wfx_remove_interface(struct ieee80211_hw *hw, /* FIXME: In add to reset MAC address, try to reset interface */ hif_set_macaddr(wvif, NULL); - cancel_delayed_work_sync(&wvif->scan.timeout); - wfx_cqm_bssloss_sm(wvif, 0, 0, 0); cancel_work_sync(&wvif->unjoin_work); - cancel_delayed_work_sync(&wvif->link_id_gc_work); - del_timer_sync(&wvif->mcast_timeout); wfx_free_event_queue(wvif); wdev->vif[wvif->id] = NULL; @@ -1666,7 +1112,7 @@ void wfx_remove_interface(struct ieee80211_hw *hw, else hif_set_block_ack_policy(wvif, 0x00, 0x00); // Combo force powersave mode. We can re-enable it now - wfx_set_pm(wvif, &wvif->powersave_mode); + wfx_update_pm(wvif); } } diff --git a/drivers/staging/wfx/sta.h b/drivers/staging/wfx/sta.h index 4ccf1b17632b..cf99a8a74a81 100644 --- a/drivers/staging/wfx/sta.h +++ b/drivers/staging/wfx/sta.h @@ -23,23 +23,11 @@ enum wfx_state { WFX_STATE_AP, }; -struct wfx_ht_info { - struct ieee80211_sta_ht_cap ht_cap; - enum nl80211_channel_type channel_type; - u16 operation_mode; -}; - struct wfx_hif_event { struct list_head link; struct hif_ind_event evt; }; -struct wfx_edca_params { - /* NOTE: index is a linux queue id. */ - struct hif_req_edca_queue_params params[IEEE80211_NUM_ACS]; - bool uapsd_enable[IEEE80211_NUM_ACS]; -}; - struct wfx_grp_addr_table { bool enable; int num_addresses; @@ -49,6 +37,9 @@ struct wfx_grp_addr_table { struct wfx_sta_priv { int link_id; int vif_id; + u8 buffered[IEEE80211_NUM_TIDS]; + // Ensure atomicity of "buffered" and calls to ieee80211_sta_set_buffered() + spinlock_t lock; }; // mac80211 interface @@ -91,13 +82,12 @@ void wfx_unassign_vif_chanctx(struct ieee80211_hw *hw, struct ieee80211_chanctx_conf *conf); // WSM Callbacks -void wfx_suspend_resume(struct wfx_vif *wvif, - struct hif_ind_suspend_resume_tx *arg); +void wfx_suspend_resume_mc(struct wfx_vif *wvif, enum sta_notify_cmd cmd); // Other Helpers void wfx_cqm_bssloss_sm(struct wfx_vif *wvif, int init, int good, int bad); void wfx_update_filtering(struct wfx_vif *wvif); -int wfx_set_pm(struct wfx_vif *wvif, const struct hif_req_set_pm_mode *arg); int wfx_fwd_probe_req(struct wfx_vif *wvif, bool enable); +u32 wfx_rate_mask_to_hw(struct wfx_dev *wdev, u32 rates); #endif /* WFX_STA_H */ diff --git a/drivers/staging/wfx/traces.h b/drivers/staging/wfx/traces.h index 3f6198ab2235..30c6a13f0e22 100644 --- a/drivers/staging/wfx/traces.h +++ b/drivers/staging/wfx/traces.h @@ -153,7 +153,7 @@ hif_mib_list_enum #define hif_mib_list hif_mib_list_enum { -1, NULL } DECLARE_EVENT_CLASS(hif_data, - TP_PROTO(struct hif_msg *hif, int tx_fill_level, bool is_recv), + TP_PROTO(const struct hif_msg *hif, int tx_fill_level, bool is_recv), TP_ARGS(hif, tx_fill_level, is_recv), TP_STRUCT__entry( __field(int, tx_fill_level) @@ -203,12 +203,12 @@ DECLARE_EVENT_CLASS(hif_data, ) ); DEFINE_EVENT(hif_data, hif_send, - TP_PROTO(struct hif_msg *hif, int tx_fill_level, bool is_recv), + TP_PROTO(const struct hif_msg *hif, int tx_fill_level, bool is_recv), TP_ARGS(hif, tx_fill_level, is_recv)); #define _trace_hif_send(hif, tx_fill_level)\ trace_hif_send(hif, tx_fill_level, false) DEFINE_EVENT(hif_data, hif_recv, - TP_PROTO(struct hif_msg *hif, int tx_fill_level, bool is_recv), + TP_PROTO(const struct hif_msg *hif, int tx_fill_level, bool is_recv), TP_ARGS(hif, tx_fill_level, is_recv)); #define _trace_hif_recv(hif, tx_fill_level)\ trace_hif_recv(hif, tx_fill_level, true) @@ -359,7 +359,8 @@ TRACE_EVENT(bh_stats, trace_bh_stats(ind, req, cnf, busy, release) TRACE_EVENT(tx_stats, - TP_PROTO(struct hif_cnf_tx *tx_cnf, struct sk_buff *skb, int delay), + TP_PROTO(const struct hif_cnf_tx *tx_cnf, const struct sk_buff *skb, + int delay), TP_ARGS(tx_cnf, skb, delay), TP_STRUCT__entry( __field(int, pkt_id) @@ -375,8 +376,9 @@ TRACE_EVENT(tx_stats, // Keep sync with wfx_rates definition in main.c static const int hw_rate[] = { 0, 1, 2, 3, 6, 7, 8, 9, 10, 11, 12, 13 }; - struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(skb); - struct ieee80211_tx_rate *rates = tx_info->driver_rates; + const struct ieee80211_tx_info *tx_info = + (const struct ieee80211_tx_info *)skb->cb; + const struct ieee80211_tx_rate *rates = tx_info->driver_rates; int i; __entry->pkt_id = tx_cnf->packet_id; diff --git a/drivers/staging/wfx/wfx.h b/drivers/staging/wfx/wfx.h index 781a8c8ba982..8b85bb1abb9c 100644 --- a/drivers/staging/wfx/wfx.h +++ b/drivers/staging/wfx/wfx.h @@ -26,6 +26,9 @@ #include "hif_tx.h" #include "hif_api_general.h" +#define USEC_PER_TXOP 32 // see struct ieee80211_tx_queue_params +#define USEC_PER_TU 1024 + struct hwbus_ops; struct wfx_dev { @@ -51,14 +54,12 @@ struct wfx_dev { int tx_burst_idx; atomic_t tx_lock; + atomic_t packet_id; u32 key_map; struct hif_req_add_key keys[MAX_KEY_ENTRIES]; struct hif_rx_stats rx_stats; struct mutex rx_stats_lock; - - int output_power; - atomic_t scan_in_progress; }; struct wfx_vif { @@ -68,24 +69,15 @@ struct wfx_vif { int id; enum wfx_state state; - int delayed_link_loss; int bss_loss_state; u32 bss_loss_confirm_id; struct mutex bss_loss_lock; struct delayed_work bss_loss_work; u32 link_id_map; - struct wfx_link_entry link_id_db[WFX_MAX_STA_IN_AP_MODE]; - struct delayed_work link_id_gc_work; - struct work_struct link_id_work; - bool aid0_bit_set; - bool mcast_tx; - bool mcast_buffered; + bool after_dtim_tx_allowed; struct wfx_grp_addr_table mcast_filter; - struct timer_list mcast_timeout; - struct work_struct mcast_start_work; - struct work_struct mcast_stop_work; s8 wep_default_key_id; struct sk_buff *wep_pending_skb; @@ -95,37 +87,30 @@ struct wfx_vif { struct work_struct tx_policy_upload_work; u32 sta_asleep_mask; - u32 pspoll_mask; spinlock_t ps_state_lock; - struct work_struct set_tim_work; + struct work_struct update_tim_work; - int dtim_period; int beacon_int; - bool enable_beacon; - struct work_struct set_beacon_wakeup_period_work; - bool filter_bssid; bool fwd_probe_req; bool disable_beacon_filter; struct work_struct update_filtering_work; - u32 erp_info; - int cqm_rssi_thold; - bool setbssparams_done; - struct wfx_ht_info ht_info; - struct wfx_edca_params edca; - struct hif_mib_set_uapsd_information uapsd_info; + unsigned long uapsd_mask; + struct ieee80211_tx_queue_params edca_params[IEEE80211_NUM_ACS]; struct hif_req_set_bss_params bss_params; struct work_struct bss_params_work; - struct work_struct set_cts_work; int join_complete_status; - bool delayed_unjoin; struct work_struct unjoin_work; - struct wfx_scan scan; + /* avoid some operations in parallel with scan */ + struct mutex scan_lock; + struct work_struct scan_work; + struct completion scan_complete; + bool scan_abort; + struct ieee80211_scan_request *scan_req; - struct hif_req_set_pm_mode powersave_mode; struct completion set_pm_mode_complete; struct list_head event_queue; diff --git a/drivers/staging/wilc1000/fw.h b/drivers/staging/wilc1000/fw.h new file mode 100644 index 000000000000..a76e1dea4345 --- /dev/null +++ b/drivers/staging/wilc1000/fw.h @@ -0,0 +1,119 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (c) 2012 - 2018 Microchip Technology Inc., and its subsidiaries. + * All rights reserved. + */ + +#ifndef WILC_FW_H +#define WILC_FW_H + +#include <linux/ieee80211.h> + +#define WILC_MAX_NUM_STA 9 +#define WILC_MAX_RATES_SUPPORTED 12 +#define WILC_MAX_NUM_PMKIDS 16 +#define WILC_MAX_NUM_SCANNED_CH 14 + +struct wilc_assoc_resp { + __le16 capab_info; + __le16 status_code; + __le16 aid; +} __packed; + +struct wilc_pmkid { + u8 bssid[ETH_ALEN]; + u8 pmkid[WLAN_PMKID_LEN]; +} __packed; + +struct wilc_pmkid_attr { + u8 numpmkid; + struct wilc_pmkid pmkidlist[WILC_MAX_NUM_PMKIDS]; +} __packed; + +struct wilc_reg_frame { + u8 reg; + u8 reg_id; + __le16 frame_type; +} __packed; + +struct wilc_drv_handler { + __le32 handler; + u8 mode; +} __packed; + +struct wilc_wep_key { + u8 index; + u8 key_len; + u8 key[0]; +} __packed; + +struct wilc_sta_wpa_ptk { + u8 mac_addr[ETH_ALEN]; + u8 key_len; + u8 key[0]; +} __packed; + +struct wilc_ap_wpa_ptk { + u8 mac_addr[ETH_ALEN]; + u8 index; + u8 key_len; + u8 key[0]; +} __packed; + +struct wilc_gtk_key { + u8 mac_addr[ETH_ALEN]; + u8 rsc[8]; + u8 index; + u8 key_len; + u8 key[0]; +} __packed; + +struct wilc_op_mode { + __le32 mode; +} __packed; + +struct wilc_noa_opp_enable { + u8 ct_window; + u8 cnt; + __le32 duration; + __le32 interval; + __le32 start_time; +} __packed; + +struct wilc_noa_opp_disable { + u8 cnt; + __le32 duration; + __le32 interval; + __le32 start_time; +} __packed; + +struct wilc_join_bss_param { + char ssid[IEEE80211_MAX_SSID_LEN]; + u8 ssid_terminator; + u8 bss_type; + u8 ch; + __le16 cap_info; + u8 sa[ETH_ALEN]; + u8 bssid[ETH_ALEN]; + __le16 beacon_period; + u8 dtim_period; + u8 supp_rates[WILC_MAX_RATES_SUPPORTED + 1]; + u8 wmm_cap; + u8 uapsd_cap; + u8 ht_capable; + u8 rsn_found; + u8 rsn_grp_policy; + u8 mode_802_11i; + u8 p_suites[3]; + u8 akm_suites[3]; + u8 rsn_cap[2]; + u8 noa_enabled; + __le32 tsf_lo; + u8 idx; + u8 opp_enabled; + union { + struct wilc_noa_opp_disable opp_dis; + struct wilc_noa_opp_enable opp_en; + }; +} __packed; +#endif diff --git a/drivers/staging/wilc1000/hif.c b/drivers/staging/wilc1000/hif.c index 349e45d58ec9..658790bd465b 100644 --- a/drivers/staging/wilc1000/hif.c +++ b/drivers/staging/wilc1000/hif.c @@ -10,7 +10,6 @@ #define WILC_HIF_CONNECT_TIMEOUT_MS 9500 #define WILC_FALSE_FRMWR_CHANNEL 100 -#define WILC_MAX_RATES_SUPPORTED 12 struct wilc_rcvd_mac_info { u8 status; @@ -27,48 +26,6 @@ struct wilc_del_all_sta { u8 mac[WILC_MAX_NUM_STA][ETH_ALEN]; }; -struct wilc_op_mode { - __le32 mode; -}; - -struct wilc_reg_frame { - u8 reg; - u8 reg_id; - __le16 frame_type; -} __packed; - -struct wilc_drv_handler { - __le32 handler; - u8 mode; -} __packed; - -struct wilc_wep_key { - u8 index; - u8 key_len; - u8 key[0]; -} __packed; - -struct wilc_sta_wpa_ptk { - u8 mac_addr[ETH_ALEN]; - u8 key_len; - u8 key[0]; -} __packed; - -struct wilc_ap_wpa_ptk { - u8 mac_addr[ETH_ALEN]; - u8 index; - u8 key_len; - u8 key[0]; -} __packed; - -struct wilc_gtk_key { - u8 mac_addr[ETH_ALEN]; - u8 rsc[8]; - u8 index; - u8 key_len; - u8 key[0]; -} __packed; - union wilc_message_body { struct wilc_rcvd_net_info net_info; struct wilc_rcvd_mac_info mac_info; @@ -86,51 +43,6 @@ struct host_if_msg { bool is_sync; }; -struct wilc_noa_opp_enable { - u8 ct_window; - u8 cnt; - __le32 duration; - __le32 interval; - __le32 start_time; -} __packed; - -struct wilc_noa_opp_disable { - u8 cnt; - __le32 duration; - __le32 interval; - __le32 start_time; -} __packed; - -struct wilc_join_bss_param { - char ssid[IEEE80211_MAX_SSID_LEN]; - u8 ssid_terminator; - u8 bss_type; - u8 ch; - __le16 cap_info; - u8 sa[ETH_ALEN]; - u8 bssid[ETH_ALEN]; - __le16 beacon_period; - u8 dtim_period; - u8 supp_rates[WILC_MAX_RATES_SUPPORTED + 1]; - u8 wmm_cap; - u8 uapsd_cap; - u8 ht_capable; - u8 rsn_found; - u8 rsn_grp_policy; - u8 mode_802_11i; - u8 p_suites[3]; - u8 akm_suites[3]; - u8 rsn_cap[2]; - u8 noa_enabled; - __le32 tsf_lo; - u8 idx; - u8 opp_enabled; - union { - struct wilc_noa_opp_disable opp_dis; - struct wilc_noa_opp_enable opp_en; - }; -} __packed; - /* 'msg' should be free by the caller for syc */ static struct host_if_msg* wilc_alloc_work(struct wilc_vif *vif, void (*work_fun)(struct work_struct *), @@ -640,7 +552,7 @@ static s32 wilc_parse_assoc_resp_info(u8 *buffer, u32 buffer_len, { u8 *ies; u16 ies_len; - struct assoc_resp *res = (struct assoc_resp *)buffer; + struct wilc_assoc_resp *res = (struct wilc_assoc_resp *)buffer; ret_conn_info->status = le16_to_cpu(res->status_code); if (ret_conn_info->status == WLAN_STATUS_SUCCESS) { diff --git a/drivers/staging/wilc1000/hif.h b/drivers/staging/wilc1000/hif.h index 22ee6fffd599..db9179171f05 100644 --- a/drivers/staging/wilc1000/hif.h +++ b/drivers/staging/wilc1000/hif.h @@ -17,14 +17,11 @@ enum { WILC_CLIENT_MODE = 0x4 }; -#define WILC_MAX_NUM_STA 9 -#define WILC_MAX_NUM_SCANNED_CH 14 #define WILC_MAX_NUM_PROBED_SSID 10 #define WILC_TX_MIC_KEY_LEN 8 #define WILC_RX_MIC_KEY_LEN 8 -#define WILC_MAX_NUM_PMKIDS 16 #define WILC_ADD_STA_LENGTH 40 #define WILC_NUM_CONCURRENT_IFC 2 @@ -35,12 +32,6 @@ enum { #define WILC_MAX_ASSOC_RESP_FRAME_SIZE 256 -struct assoc_resp { - __le16 capab_info; - __le16 status_code; - __le16 aid; -} __packed; - struct rf_info { u8 link_speed; s8 rssi; @@ -59,16 +50,6 @@ enum host_if_state { HOST_IF_FORCE_32BIT = 0xFFFFFFFF }; -struct wilc_pmkid { - u8 bssid[ETH_ALEN]; - u8 pmkid[WLAN_PMKID_LEN]; -} __packed; - -struct wilc_pmkid_attr { - u8 numpmkid; - struct wilc_pmkid pmkidlist[WILC_MAX_NUM_PMKIDS]; -} __packed; - struct cfg_param_attr { u32 flag; u16 short_retry_limit; diff --git a/drivers/staging/wilc1000/netdev.c b/drivers/staging/wilc1000/netdev.c index d2c0b0f7cf63..fce5bf2d82fa 100644 --- a/drivers/staging/wilc1000/netdev.c +++ b/drivers/staging/wilc1000/netdev.c @@ -96,21 +96,18 @@ void wilc_mac_indicate(struct wilc *wilc) static struct net_device *get_if_handler(struct wilc *wilc, u8 *mac_header) { - u8 *bssid, *bssid1; struct net_device *ndev = NULL; struct wilc_vif *vif; - - bssid = mac_header + 10; - bssid1 = mac_header + 4; + struct ieee80211_hdr *h = (struct ieee80211_hdr *)mac_header; list_for_each_entry_rcu(vif, &wilc->vif_list, list) { if (vif->mode == WILC_STATION_MODE) - if (ether_addr_equal_unaligned(bssid, vif->bssid)) { + if (ether_addr_equal_unaligned(h->addr2, vif->bssid)) { ndev = vif->ndev; goto out; } if (vif->mode == WILC_AP_MODE) - if (ether_addr_equal_unaligned(bssid1, vif->bssid)) { + if (ether_addr_equal_unaligned(h->addr1, vif->bssid)) { ndev = vif->ndev; goto out; } @@ -177,7 +174,7 @@ static int wilc_txq_task(void *vp) } srcu_read_unlock(&wl->srcu, srcu_idx); } - } while (ret == -ENOBUFS && !wl->close); + } while (ret == WILC_VMM_ENTRY_FULL_RETRY && !wl->close); } return 0; } @@ -186,7 +183,7 @@ static int wilc_wlan_get_firmware(struct net_device *dev) { struct wilc_vif *vif = netdev_priv(dev); struct wilc *wilc = vif->wilc; - int chip_id, ret = 0; + int chip_id; const struct firmware *wilc_firmware; char *firmware; @@ -201,14 +198,11 @@ static int wilc_wlan_get_firmware(struct net_device *dev) if (request_firmware(&wilc_firmware, firmware, wilc->dev) != 0) { netdev_err(dev, "%s - firmware not available\n", firmware); - ret = -1; - goto fail; + return -EINVAL; } wilc->firmware = wilc_firmware; -fail: - - return ret; + return 0; } static int wilc_start_firmware(struct net_device *dev) @@ -218,7 +212,7 @@ static int wilc_start_firmware(struct net_device *dev) int ret = 0; ret = wilc_wlan_start(wilc); - if (ret < 0) + if (ret) return ret; if (!wait_for_completion_timeout(&wilc->sync_event, @@ -241,7 +235,7 @@ static int wilc1000_firmware_download(struct net_device *dev) ret = wilc_wlan_firmware_download(wilc, wilc->firmware->data, wilc->firmware->size); - if (ret < 0) + if (ret) return ret; release_firmware(wilc->firmware); @@ -420,7 +414,7 @@ static int wilc_init_fw_config(struct net_device *dev, struct wilc_vif *vif) return 0; fail: - return -1; + return -EINVAL; } static void wlan_deinitialize_threads(struct net_device *dev) @@ -500,14 +494,12 @@ static int wilc_wlan_initialize(struct net_device *dev, struct wilc_vif *vif) wl->close = 0; ret = wilc_wlan_init(dev); - if (ret < 0) - return -EIO; + if (ret) + return ret; ret = wlan_initialize_threads(dev); - if (ret < 0) { - ret = -EIO; + if (ret) goto fail_wilc_wlan; - } if (wl->gpio_irq && init_irq(dev)) { ret = -EIO; @@ -521,22 +513,17 @@ static int wilc_wlan_initialize(struct net_device *dev, struct wilc_vif *vif) goto fail_irq_init; } - if (wilc_wlan_get_firmware(dev)) { - ret = -EIO; + ret = wilc_wlan_get_firmware(dev); + if (ret) goto fail_irq_enable; - } ret = wilc1000_firmware_download(dev); - if (ret < 0) { - ret = -EIO; + if (ret) goto fail_irq_enable; - } ret = wilc_start_firmware(dev); - if (ret < 0) { - ret = -EIO; + if (ret) goto fail_irq_enable; - } if (wilc_wlan_cfg_get(vif, 1, WID_FIRMWARE_VERSION, 1, 0)) { int size; @@ -548,11 +535,10 @@ static int wilc_wlan_initialize(struct net_device *dev, struct wilc_vif *vif) firmware_ver[size] = '\0'; netdev_dbg(dev, "Firmware Ver = %s\n", firmware_ver); } - ret = wilc_init_fw_config(dev, vif); - if (ret < 0) { + ret = wilc_init_fw_config(dev, vif); + if (ret) { netdev_err(dev, "Failed to configure firmware\n"); - ret = -EIO; goto fail_fw_start; } wl->initialized = true; @@ -603,11 +589,11 @@ static int wilc_mac_open(struct net_device *ndev) netdev_dbg(ndev, "MAC OPEN[%p]\n", ndev); ret = wilc_init_host_int(ndev); - if (ret < 0) + if (ret) return ret; ret = wilc_wlan_initialize(ndev, vif); - if (ret < 0) { + if (ret) { wilc_deinit_host_int(ndev); return ret; } @@ -840,7 +826,7 @@ static const struct net_device_ops wilc_netdev_ops = { void wilc_netdev_cleanup(struct wilc *wilc) { struct wilc_vif *vif; - int srcu_idx; + int srcu_idx, ifc_cnt = 0; if (!wilc) return; @@ -861,7 +847,7 @@ void wilc_netdev_cleanup(struct wilc *wilc) flush_workqueue(wilc->hif_workqueue); destroy_workqueue(wilc->hif_workqueue); - do { + while (ifc_cnt < WILC_NUM_CONCURRENT_IFC) { mutex_lock(&wilc->vif_mutex); if (wilc->vif_num <= 0) { mutex_unlock(&wilc->vif_mutex); @@ -874,7 +860,8 @@ void wilc_netdev_cleanup(struct wilc *wilc) wilc->vif_num--; mutex_unlock(&wilc->vif_mutex); synchronize_srcu(&wilc->srcu); - } while (1); + ifc_cnt++; + } wilc_wlan_cfg_deinit(wilc); wlan_deinit_locks(wilc); diff --git a/drivers/staging/wilc1000/netdev.h b/drivers/staging/wilc1000/netdev.h index cd8f0d72caaa..d5f7a6037fbc 100644 --- a/drivers/staging/wilc1000/netdev.h +++ b/drivers/staging/wilc1000/netdev.h @@ -21,7 +21,6 @@ #define FLOW_CONTROL_LOWER_THRESHOLD 128 #define FLOW_CONTROL_UPPER_THRESHOLD 256 -#define WILC_MAX_NUM_PMKIDS 16 #define PMKID_FOUND 1 #define NUM_STA_ASSOCIATED 8 diff --git a/drivers/staging/wilc1000/sdio.c b/drivers/staging/wilc1000/sdio.c index 319e039380b0..ca99335687c4 100644 --- a/drivers/staging/wilc1000/sdio.c +++ b/drivers/staging/wilc1000/sdio.c @@ -273,7 +273,7 @@ static int wilc_sdio_set_func0_csa_address(struct wilc *wilc, u32 adr) ret = wilc_sdio_cmd52(wilc, &cmd); if (ret) { dev_err(&func->dev, "Failed cmd52, set 0x10c data...\n"); - goto fail; + return ret; } cmd.address = 0x10d; @@ -281,7 +281,7 @@ static int wilc_sdio_set_func0_csa_address(struct wilc *wilc, u32 adr) ret = wilc_sdio_cmd52(wilc, &cmd); if (ret) { dev_err(&func->dev, "Failed cmd52, set 0x10d data...\n"); - goto fail; + return ret; } cmd.address = 0x10e; @@ -289,11 +289,9 @@ static int wilc_sdio_set_func0_csa_address(struct wilc *wilc, u32 adr) ret = wilc_sdio_cmd52(wilc, &cmd); if (ret) { dev_err(&func->dev, "Failed cmd52, set 0x10e data...\n"); - goto fail; + return ret; } - return 1; -fail: return 0; } @@ -311,7 +309,7 @@ static int wilc_sdio_set_func0_block_size(struct wilc *wilc, u32 block_size) ret = wilc_sdio_cmd52(wilc, &cmd); if (ret) { dev_err(&func->dev, "Failed cmd52, set 0x10 data...\n"); - goto fail; + return ret; } cmd.address = 0x11; @@ -319,11 +317,9 @@ static int wilc_sdio_set_func0_block_size(struct wilc *wilc, u32 block_size) ret = wilc_sdio_cmd52(wilc, &cmd); if (ret) { dev_err(&func->dev, "Failed cmd52, set 0x11 data...\n"); - goto fail; + return ret; } - return 1; -fail: return 0; } @@ -347,18 +343,16 @@ static int wilc_sdio_set_func1_block_size(struct wilc *wilc, u32 block_size) ret = wilc_sdio_cmd52(wilc, &cmd); if (ret) { dev_err(&func->dev, "Failed cmd52, set 0x110 data...\n"); - goto fail; + return ret; } cmd.address = 0x111; cmd.data = (u8)(block_size >> 8); ret = wilc_sdio_cmd52(wilc, &cmd); if (ret) { dev_err(&func->dev, "Failed cmd52, set 0x111 data...\n"); - goto fail; + return ret; } - return 1; -fail: return 0; } @@ -384,19 +378,18 @@ static int wilc_sdio_write_reg(struct wilc *wilc, u32 addr, u32 data) cmd.address = addr; cmd.data = data; ret = wilc_sdio_cmd52(wilc, &cmd); - if (ret) { + if (ret) dev_err(&func->dev, "Failed cmd 52, read reg (%08x) ...\n", addr); - goto fail; - } } else { struct sdio_cmd53 cmd; /** * set the AHB address **/ - if (!wilc_sdio_set_func0_csa_address(wilc, addr)) - goto fail; + ret = wilc_sdio_set_func0_csa_address(wilc, addr); + if (ret) + return ret; cmd.read_write = 1; cmd.function = 0; @@ -407,18 +400,12 @@ static int wilc_sdio_write_reg(struct wilc *wilc, u32 addr, u32 data) cmd.buffer = (u8 *)&data; cmd.block_size = sdio_priv->block_size; ret = wilc_sdio_cmd53(wilc, &cmd); - if (ret) { + if (ret) dev_err(&func->dev, "Failed cmd53, write reg (%08x)...\n", addr); - goto fail; - } } - return 1; - -fail: - - return 0; + return ret; } static int wilc_sdio_write(struct wilc *wilc, u32 addr, u8 *buf, u32 size) @@ -470,14 +457,15 @@ static int wilc_sdio_write(struct wilc *wilc, u32 addr, u8 *buf, u32 size) cmd.buffer = buf; cmd.block_size = block_size; if (addr > 0) { - if (!wilc_sdio_set_func0_csa_address(wilc, addr)) - goto fail; + ret = wilc_sdio_set_func0_csa_address(wilc, addr); + if (ret) + return ret; } ret = wilc_sdio_cmd53(wilc, &cmd); if (ret) { dev_err(&func->dev, "Failed cmd53 [%x], block send...\n", addr); - goto fail; + return ret; } if (addr > 0) addr += nblk * block_size; @@ -493,21 +481,18 @@ static int wilc_sdio_write(struct wilc *wilc, u32 addr, u8 *buf, u32 size) cmd.block_size = block_size; if (addr > 0) { - if (!wilc_sdio_set_func0_csa_address(wilc, addr)) - goto fail; + ret = wilc_sdio_set_func0_csa_address(wilc, addr); + if (ret) + return ret; } ret = wilc_sdio_cmd53(wilc, &cmd); if (ret) { dev_err(&func->dev, "Failed cmd53 [%x], bytes send...\n", addr); - goto fail; + return ret; } } - return 1; - -fail: - return 0; } @@ -528,14 +513,15 @@ static int wilc_sdio_read_reg(struct wilc *wilc, u32 addr, u32 *data) if (ret) { dev_err(&func->dev, "Failed cmd 52, read reg (%08x) ...\n", addr); - goto fail; + return ret; } *data = cmd.data; } else { struct sdio_cmd53 cmd; - if (!wilc_sdio_set_func0_csa_address(wilc, addr)) - goto fail; + ret = wilc_sdio_set_func0_csa_address(wilc, addr); + if (ret) + return ret; cmd.read_write = 0; cmd.function = 0; @@ -550,16 +536,11 @@ static int wilc_sdio_read_reg(struct wilc *wilc, u32 addr, u32 *data) if (ret) { dev_err(&func->dev, "Failed cmd53, read reg (%08x)...\n", addr); - goto fail; + return ret; } } le32_to_cpus(data); - - return 1; - -fail: - return 0; } @@ -612,14 +593,15 @@ static int wilc_sdio_read(struct wilc *wilc, u32 addr, u8 *buf, u32 size) cmd.buffer = buf; cmd.block_size = block_size; if (addr > 0) { - if (!wilc_sdio_set_func0_csa_address(wilc, addr)) - goto fail; + ret = wilc_sdio_set_func0_csa_address(wilc, addr); + if (ret) + return ret; } ret = wilc_sdio_cmd53(wilc, &cmd); if (ret) { dev_err(&func->dev, "Failed cmd53 [%x], block read...\n", addr); - goto fail; + return ret; } if (addr > 0) addr += nblk * block_size; @@ -635,21 +617,18 @@ static int wilc_sdio_read(struct wilc *wilc, u32 addr, u8 *buf, u32 size) cmd.block_size = block_size; if (addr > 0) { - if (!wilc_sdio_set_func0_csa_address(wilc, addr)) - goto fail; + ret = wilc_sdio_set_func0_csa_address(wilc, addr); + if (ret) + return ret; } ret = wilc_sdio_cmd53(wilc, &cmd); if (ret) { dev_err(&func->dev, "Failed cmd53 [%x], bytes read...\n", addr); - goto fail; + return ret; } } - return 1; - -fail: - return 0; } @@ -661,7 +640,7 @@ fail: static int wilc_sdio_deinit(struct wilc *wilc) { - return 1; + return 0; } static int wilc_sdio_init(struct wilc *wilc, bool resume) @@ -686,15 +665,16 @@ static int wilc_sdio_init(struct wilc *wilc, bool resume) ret = wilc_sdio_cmd52(wilc, &cmd); if (ret) { dev_err(&func->dev, "Fail cmd 52, enable csa...\n"); - goto fail; + return ret; } /** * function 0 block size **/ - if (!wilc_sdio_set_func0_block_size(wilc, WILC_SDIO_BLOCK_SIZE)) { + ret = wilc_sdio_set_func0_block_size(wilc, WILC_SDIO_BLOCK_SIZE); + if (ret) { dev_err(&func->dev, "Fail cmd 52, set func 0 block size...\n"); - goto fail; + return ret; } sdio_priv->block_size = WILC_SDIO_BLOCK_SIZE; @@ -710,7 +690,7 @@ static int wilc_sdio_init(struct wilc *wilc, bool resume) if (ret) { dev_err(&func->dev, "Fail cmd 52, set IOE register...\n"); - goto fail; + return ret; } /** @@ -727,7 +707,7 @@ static int wilc_sdio_init(struct wilc *wilc, bool resume) if (ret) { dev_err(&func->dev, "Fail cmd 52, get IOR register...\n"); - goto fail; + return ret; } if (cmd.data == 0x2) break; @@ -735,15 +715,16 @@ static int wilc_sdio_init(struct wilc *wilc, bool resume) if (loop <= 0) { dev_err(&func->dev, "Fail func 1 is not ready...\n"); - goto fail; + return -EINVAL; } /** * func 1 is ready, set func 1 block size **/ - if (!wilc_sdio_set_func1_block_size(wilc, WILC_SDIO_BLOCK_SIZE)) { + ret = wilc_sdio_set_func1_block_size(wilc, WILC_SDIO_BLOCK_SIZE); + if (ret) { dev_err(&func->dev, "Fail set func 1 block size...\n"); - goto fail; + return ret; } /** @@ -757,16 +738,17 @@ static int wilc_sdio_init(struct wilc *wilc, bool resume) ret = wilc_sdio_cmd52(wilc, &cmd); if (ret) { dev_err(&func->dev, "Fail cmd 52, set IEN register...\n"); - goto fail; + return ret; } /** * make sure can read back chip id correctly **/ if (!resume) { - if (!wilc_sdio_read_reg(wilc, 0x1000, &chipid)) { + ret = wilc_sdio_read_reg(wilc, 0x1000, &chipid); + if (ret) { dev_err(&func->dev, "Fail cmd read chip id...\n"); - goto fail; + return ret; } dev_err(&func->dev, "chipid (%08x)\n", chipid); if ((chipid & 0xfff) > 0x2a0) @@ -777,10 +759,6 @@ static int wilc_sdio_init(struct wilc *wilc, bool resume) sdio_priv->has_thrpt_enh3); } - return 1; - -fail: - return 0; } @@ -806,7 +784,7 @@ static int wilc_sdio_read_size(struct wilc *wilc, u32 *size) tmp |= (cmd.data << 8); *size = tmp; - return 1; + return 0; } static int wilc_sdio_read_int(struct wilc *wilc, u32 *int_status) @@ -865,7 +843,7 @@ static int wilc_sdio_read_int(struct wilc *wilc, u32 *int_status) *int_status = tmp; - return 1; + return 0; } static int wilc_sdio_clear_int_ext(struct wilc *wilc, u32 val) @@ -909,10 +887,10 @@ static int wilc_sdio_clear_int_ext(struct wilc *wilc, u32 val) dev_err(&func->dev, "Failed cmd52, set 0xf8 data (%d) ...\n", __LINE__); - goto fail; + return ret; } } - return 1; + return 0; } if (sdio_priv->irq_gpio) { /* has_thrpt_enh2 uses register 0xf8 to clear interrupts. */ @@ -926,7 +904,6 @@ static int wilc_sdio_clear_int_ext(struct wilc *wilc, u32 val) if (flags) { int i; - ret = 1; for (i = 0; i < sdio_priv->nint; i++) { if (flags & 1) { struct sdio_cmd52 cmd; @@ -942,15 +919,12 @@ static int wilc_sdio_clear_int_ext(struct wilc *wilc, u32 val) dev_err(&func->dev, "Failed cmd52, set 0xf8 data (%d) ...\n", __LINE__); - goto fail; + return ret; } } - if (!ret) - break; flags >>= 1; } - if (!ret) - goto fail; + for (i = sdio_priv->nint; i < MAX_NUM_INT; i++) { if (flags & 1) dev_err(&func->dev, @@ -985,11 +959,9 @@ static int wilc_sdio_clear_int_ext(struct wilc *wilc, u32 val) dev_err(&func->dev, "Failed cmd52, set 0xf6 data (%d) ...\n", __LINE__); - goto fail; + return ret; } } - return 1; -fail: return 0; } @@ -1001,12 +973,12 @@ static int wilc_sdio_sync_ext(struct wilc *wilc, int nint) if (nint > MAX_NUM_INT) { dev_err(&func->dev, "Too many interrupts (%d)...\n", nint); - return 0; + return -EINVAL; } if (nint > MAX_NUN_INT_THRPT_ENH2) { dev_err(&func->dev, "Cannot support more than 5 interrupts when has_thrpt_enh2=1.\n"); - return 0; + return -EINVAL; } sdio_priv->nint = nint; @@ -1014,15 +986,15 @@ static int wilc_sdio_sync_ext(struct wilc *wilc, int nint) /** * Disable power sequencer **/ - if (!wilc_sdio_read_reg(wilc, WILC_MISC, ®)) { + if (wilc_sdio_read_reg(wilc, WILC_MISC, ®)) { dev_err(&func->dev, "Failed read misc reg...\n"); - return 0; + return -EINVAL; } reg &= ~BIT(8); - if (!wilc_sdio_write_reg(wilc, WILC_MISC, reg)) { + if (wilc_sdio_write_reg(wilc, WILC_MISC, reg)) { dev_err(&func->dev, "Failed write misc reg...\n"); - return 0; + return -EINVAL; } if (sdio_priv->irq_gpio) { @@ -1033,59 +1005,59 @@ static int wilc_sdio_sync_ext(struct wilc *wilc, int nint) * interrupt pin mux select **/ ret = wilc_sdio_read_reg(wilc, WILC_PIN_MUX_0, ®); - if (!ret) { + if (ret) { dev_err(&func->dev, "Failed read reg (%08x)...\n", WILC_PIN_MUX_0); - return 0; + return ret; } reg |= BIT(8); ret = wilc_sdio_write_reg(wilc, WILC_PIN_MUX_0, reg); - if (!ret) { + if (ret) { dev_err(&func->dev, "Failed write reg (%08x)...\n", WILC_PIN_MUX_0); - return 0; + return ret; } /** * interrupt enable **/ ret = wilc_sdio_read_reg(wilc, WILC_INTR_ENABLE, ®); - if (!ret) { + if (ret) { dev_err(&func->dev, "Failed read reg (%08x)...\n", WILC_INTR_ENABLE); - return 0; + return ret; } for (i = 0; (i < 5) && (nint > 0); i++, nint--) reg |= BIT((27 + i)); ret = wilc_sdio_write_reg(wilc, WILC_INTR_ENABLE, reg); - if (!ret) { + if (ret) { dev_err(&func->dev, "Failed write reg (%08x)...\n", WILC_INTR_ENABLE); - return 0; + return ret; } if (nint) { ret = wilc_sdio_read_reg(wilc, WILC_INTR2_ENABLE, ®); - if (!ret) { + if (ret) { dev_err(&func->dev, "Failed read reg (%08x)...\n", WILC_INTR2_ENABLE); - return 0; + return ret; } for (i = 0; (i < 3) && (nint > 0); i++, nint--) reg |= BIT(i); ret = wilc_sdio_read_reg(wilc, WILC_INTR2_ENABLE, ®); - if (!ret) { + if (ret) { dev_err(&func->dev, "Failed write reg (%08x)...\n", WILC_INTR2_ENABLE); - return 0; + return ret; } } } - return 1; + return 0; } /* Global sdio HIF function table */ diff --git a/drivers/staging/wilc1000/spi.c b/drivers/staging/wilc1000/spi.c index 55f8757325f0..3ffc7b4fddf6 100644 --- a/drivers/staging/wilc1000/spi.c +++ b/drivers/staging/wilc1000/spi.c @@ -13,7 +13,6 @@ struct wilc_spi { int crc_off; int nint; - int has_thrpt_enh; }; static const struct wilc_hif_func wilc_hif_spi; @@ -89,11 +88,6 @@ static u8 crc7(u8 crc, const u8 *buffer, u32 len) #define CMD_SINGLE_READ 0xca #define CMD_RESET 0xcf -#define N_OK 1 -#define N_FAIL 0 -#define N_RESET -1 -#define N_RETRY -2 - #define DATA_PKT_SZ_256 256 #define DATA_PKT_SZ_512 512 #define DATA_PKT_SZ_1K 1024 @@ -300,7 +294,7 @@ static int spi_cmd_complete(struct wilc *wilc, u8 cmd, u32 adr, u8 *b, u32 sz, u32 len2; u8 rsp; int len = 0; - int result = N_OK; + int result = 0; int retry; u8 crc[2]; @@ -388,11 +382,11 @@ static int spi_cmd_complete(struct wilc *wilc, u8 cmd, u32 adr, u8 *b, u32 sz, break; default: - result = N_FAIL; + result = -EINVAL; break; } - if (result != N_OK) + if (result) return result; if (!spi_priv->crc_off) @@ -425,7 +419,7 @@ static int spi_cmd_complete(struct wilc *wilc, u8 cmd, u32 adr, u8 *b, u32 sz, if (len2 > ARRAY_SIZE(wb)) { dev_err(&spi->dev, "spi buffer size too small (%d) (%zu)\n", len2, ARRAY_SIZE(wb)); - return N_FAIL; + return -EINVAL; } /* zero spi write buffers. */ for (wix = len; wix < len2; wix++) @@ -434,7 +428,7 @@ static int spi_cmd_complete(struct wilc *wilc, u8 cmd, u32 adr, u8 *b, u32 sz, if (wilc_spi_tx_rx(wilc, wb, rb, len2)) { dev_err(&spi->dev, "Failed cmd write, bus error...\n"); - return N_FAIL; + return -EINVAL; } /* @@ -449,7 +443,7 @@ static int spi_cmd_complete(struct wilc *wilc, u8 cmd, u32 adr, u8 *b, u32 sz, dev_err(&spi->dev, "Failed cmd response, cmd (%02x), resp (%02x)\n", cmd, rsp); - return N_FAIL; + return -EINVAL; } /* @@ -459,7 +453,7 @@ static int spi_cmd_complete(struct wilc *wilc, u8 cmd, u32 adr, u8 *b, u32 sz, if (rsp != 0x00) { dev_err(&spi->dev, "Failed cmd state response state (%02x)\n", rsp); - return N_FAIL; + return -EINVAL; } if (cmd == CMD_INTERNAL_READ || cmd == CMD_SINGLE_READ || @@ -486,7 +480,7 @@ static int spi_cmd_complete(struct wilc *wilc, u8 cmd, u32 adr, u8 *b, u32 sz, if (retry <= 0) { dev_err(&spi->dev, "Error, data read response (%02x)\n", rsp); - return N_RESET; + return -EAGAIN; } } @@ -502,7 +496,7 @@ static int spi_cmd_complete(struct wilc *wilc, u8 cmd, u32 adr, u8 *b, u32 sz, } else { dev_err(&spi->dev, "buffer overrun when reading data.\n"); - return N_FAIL; + return -EINVAL; } if (!spi_priv->crc_off) { @@ -515,7 +509,7 @@ static int spi_cmd_complete(struct wilc *wilc, u8 cmd, u32 adr, u8 *b, u32 sz, } else { dev_err(&spi->dev, "buffer overrun when reading crc.\n"); - return N_FAIL; + return -EINVAL; } } } else if ((cmd == CMD_DMA_READ) || (cmd == CMD_DMA_EXT_READ)) { @@ -541,7 +535,7 @@ static int spi_cmd_complete(struct wilc *wilc, u8 cmd, u32 adr, u8 *b, u32 sz, if (wilc_spi_rx(wilc, &b[ix], nbytes)) { dev_err(&spi->dev, "Failed block read, bus err\n"); - return N_FAIL; + return -EINVAL; } /* @@ -550,7 +544,7 @@ static int spi_cmd_complete(struct wilc *wilc, u8 cmd, u32 adr, u8 *b, u32 sz, if (!spi_priv->crc_off && wilc_spi_rx(wilc, crc, 2)) { dev_err(&spi->dev, "Failed block crc read, bus err\n"); - return N_FAIL; + return -EINVAL; } ix += nbytes; @@ -582,14 +576,14 @@ static int spi_cmd_complete(struct wilc *wilc, u8 cmd, u32 adr, u8 *b, u32 sz, if (wilc_spi_rx(wilc, &rsp, 1)) { dev_err(&spi->dev, "Failed resp read, bus err\n"); - result = N_FAIL; + result = -EINVAL; break; } if (((rsp >> 4) & 0xf) == 0xf) break; } while (retry--); - if (result == N_FAIL) + if (result) break; /* @@ -598,7 +592,7 @@ static int spi_cmd_complete(struct wilc *wilc, u8 cmd, u32 adr, u8 *b, u32 sz, if (wilc_spi_rx(wilc, &b[ix], nbytes)) { dev_err(&spi->dev, "Failed block read, bus err\n"); - result = N_FAIL; + result = -EINVAL; break; } @@ -608,7 +602,7 @@ static int spi_cmd_complete(struct wilc *wilc, u8 cmd, u32 adr, u8 *b, u32 sz, if (!spi_priv->crc_off && wilc_spi_rx(wilc, crc, 2)) { dev_err(&spi->dev, "Failed block crc read, bus err\n"); - result = N_FAIL; + result = -EINVAL; break; } @@ -624,7 +618,7 @@ static int spi_data_write(struct wilc *wilc, u8 *b, u32 sz) struct spi_device *spi = to_spi_device(wilc->dev); struct wilc_spi *spi_priv = wilc->bus_data; int ix, nbytes; - int result = 1; + int result = 0; u8 cmd, order, crc[2] = {0}; /* @@ -652,7 +646,7 @@ static int spi_data_write(struct wilc *wilc, u8 *b, u32 sz) if (wilc_spi_tx(wilc, &cmd, 1)) { dev_err(&spi->dev, "Failed data block cmd write, bus error...\n"); - result = N_FAIL; + result = -EINVAL; break; } @@ -662,7 +656,7 @@ static int spi_data_write(struct wilc *wilc, u8 *b, u32 sz) if (wilc_spi_tx(wilc, &b[ix], nbytes)) { dev_err(&spi->dev, "Failed data block write, bus error...\n"); - result = N_FAIL; + result = -EINVAL; break; } @@ -672,7 +666,7 @@ static int spi_data_write(struct wilc *wilc, u8 *b, u32 sz) if (!spi_priv->crc_off) { if (wilc_spi_tx(wilc, crc, 2)) { dev_err(&spi->dev, "Failed data block crc write, bus error...\n"); - result = N_FAIL; + result = -EINVAL; break; } } @@ -701,7 +695,7 @@ static int spi_internal_write(struct wilc *wilc, u32 adr, u32 dat) cpu_to_le32s(&dat); result = spi_cmd_complete(wilc, CMD_INTERNAL_WRITE, adr, (u8 *)&dat, 4, 0); - if (result != N_OK) + if (result) dev_err(&spi->dev, "Failed internal write cmd...\n"); return result; @@ -714,14 +708,14 @@ static int spi_internal_read(struct wilc *wilc, u32 adr, u32 *data) result = spi_cmd_complete(wilc, CMD_INTERNAL_READ, adr, (u8 *)data, 4, 0); - if (result != N_OK) { + if (result) { dev_err(&spi->dev, "Failed internal read cmd...\n"); - return 0; + return result; } le32_to_cpus(data); - return 1; + return result; } /******************************************** @@ -733,7 +727,7 @@ static int spi_internal_read(struct wilc *wilc, u32 adr, u32 *data) static int wilc_spi_write_reg(struct wilc *wilc, u32 addr, u32 data) { struct spi_device *spi = to_spi_device(wilc->dev); - int result = N_OK; + int result; u8 cmd = CMD_SINGLE_WRITE; u8 clockless = 0; @@ -745,7 +739,7 @@ static int wilc_spi_write_reg(struct wilc *wilc, u32 addr, u32 data) } result = spi_cmd_complete(wilc, cmd, addr, (u8 *)&data, 4, clockless); - if (result != N_OK) + if (result) dev_err(&spi->dev, "Failed cmd, write reg (%08x)...\n", addr); return result; @@ -760,29 +754,29 @@ static int wilc_spi_write(struct wilc *wilc, u32 addr, u8 *buf, u32 size) * has to be greated than 4 */ if (size <= 4) - return 0; + return -EINVAL; result = spi_cmd_complete(wilc, CMD_DMA_EXT_WRITE, addr, NULL, size, 0); - if (result != N_OK) { + if (result) { dev_err(&spi->dev, "Failed cmd, write block (%08x)...\n", addr); - return 0; + return result; } /* * Data */ result = spi_data_write(wilc, buf, size); - if (result != N_OK) + if (result) dev_err(&spi->dev, "Failed block data write...\n"); - return 1; + return result; } static int wilc_spi_read_reg(struct wilc *wilc, u32 addr, u32 *data) { struct spi_device *spi = to_spi_device(wilc->dev); - int result = N_OK; + int result; u8 cmd = CMD_SINGLE_READ; u8 clockless = 0; @@ -793,14 +787,14 @@ static int wilc_spi_read_reg(struct wilc *wilc, u32 addr, u32 *data) } result = spi_cmd_complete(wilc, cmd, addr, (u8 *)data, 4, clockless); - if (result != N_OK) { + if (result) { dev_err(&spi->dev, "Failed cmd, read reg (%08x)...\n", addr); - return 0; + return result; } le32_to_cpus(data); - return 1; + return 0; } static int wilc_spi_read(struct wilc *wilc, u32 addr, u8 *buf, u32 size) @@ -809,15 +803,13 @@ static int wilc_spi_read(struct wilc *wilc, u32 addr, u8 *buf, u32 size) int result; if (size <= 4) - return 0; + return -EINVAL; result = spi_cmd_complete(wilc, CMD_DMA_EXT_READ, addr, buf, size, 0); - if (result != N_OK) { + if (result) dev_err(&spi->dev, "Failed cmd, read block (%08x)...\n", addr); - return 0; - } - return 1; + return result; } /******************************************** @@ -831,7 +823,7 @@ static int wilc_spi_deinit(struct wilc *wilc) /* * TODO: */ - return 1; + return 0; } static int wilc_spi_init(struct wilc *wilc, bool resume) @@ -841,13 +833,14 @@ static int wilc_spi_init(struct wilc *wilc, bool resume) u32 reg; u32 chipid; static int isinit; + int ret; if (isinit) { - if (!wilc_spi_read_reg(wilc, 0x1000, &chipid)) { + ret = wilc_spi_read_reg(wilc, 0x1000, &chipid); + if (ret) dev_err(&spi->dev, "Fail cmd read chip id...\n"); - return 0; - } - return 1; + + return ret; } /* @@ -859,7 +852,8 @@ static int wilc_spi_init(struct wilc *wilc, bool resume) * way to reset */ /* the SPI to it's initial value. */ - if (!spi_internal_read(wilc, WILC_SPI_PROTOCOL_OFFSET, ®)) { + ret = spi_internal_read(wilc, WILC_SPI_PROTOCOL_OFFSET, ®); + if (ret) { /* * Read failed. Try with CRC off. This might happen when module * is removed but chip isn't reset @@ -867,24 +861,26 @@ static int wilc_spi_init(struct wilc *wilc, bool resume) spi_priv->crc_off = 1; dev_err(&spi->dev, "Failed read with CRC on, retrying with CRC off\n"); - if (!spi_internal_read(wilc, WILC_SPI_PROTOCOL_OFFSET, ®)) { + ret = spi_internal_read(wilc, WILC_SPI_PROTOCOL_OFFSET, ®); + if (ret) { /* * Read failed with both CRC on and off, * something went bad */ dev_err(&spi->dev, "Failed internal read protocol\n"); - return 0; + return ret; } } if (spi_priv->crc_off == 0) { reg &= ~0xc; /* disable crc checking */ reg &= ~0x70; reg |= (0x5 << 4); - if (!spi_internal_write(wilc, WILC_SPI_PROTOCOL_OFFSET, reg)) { + ret = spi_internal_write(wilc, WILC_SPI_PROTOCOL_OFFSET, reg); + if (ret) { dev_err(&spi->dev, "[wilc spi %d]: Failed internal write reg\n", __LINE__); - return 0; + return ret; } spi_priv->crc_off = 1; } @@ -892,168 +888,35 @@ static int wilc_spi_init(struct wilc *wilc, bool resume) /* * make sure can read back chip id correctly */ - if (!wilc_spi_read_reg(wilc, 0x1000, &chipid)) { + ret = wilc_spi_read_reg(wilc, 0x1000, &chipid); + if (ret) { dev_err(&spi->dev, "Fail cmd read chip id...\n"); - return 0; + return ret; } - spi_priv->has_thrpt_enh = 1; - isinit = 1; - return 1; + return 0; } static int wilc_spi_read_size(struct wilc *wilc, u32 *size) { - struct spi_device *spi = to_spi_device(wilc->dev); - struct wilc_spi *spi_priv = wilc->bus_data; int ret; - if (spi_priv->has_thrpt_enh) { - ret = spi_internal_read(wilc, 0xe840 - WILC_SPI_REG_BASE, - size); - *size = *size & IRQ_DMA_WD_CNT_MASK; - } else { - u32 tmp; - u32 byte_cnt; - - ret = wilc_spi_read_reg(wilc, WILC_VMM_TO_HOST_SIZE, - &byte_cnt); - if (!ret) { - dev_err(&spi->dev, - "Failed read WILC_VMM_TO_HOST_SIZE ...\n"); - return ret; - } - tmp = (byte_cnt >> 2) & IRQ_DMA_WD_CNT_MASK; - *size = tmp; - } + ret = spi_internal_read(wilc, 0xe840 - WILC_SPI_REG_BASE, size); + *size = *size & IRQ_DMA_WD_CNT_MASK; return ret; } static int wilc_spi_read_int(struct wilc *wilc, u32 *int_status) { - struct spi_device *spi = to_spi_device(wilc->dev); - struct wilc_spi *spi_priv = wilc->bus_data; - int ret; - u32 tmp; - u32 byte_cnt; - bool unexpected_irq; - int j; - u32 unknown_mask; - u32 irq_flags; - int k = IRG_FLAGS_OFFSET + 5; - - if (spi_priv->has_thrpt_enh) - return spi_internal_read(wilc, 0xe840 - WILC_SPI_REG_BASE, - int_status); - ret = wilc_spi_read_reg(wilc, WILC_VMM_TO_HOST_SIZE, &byte_cnt); - if (!ret) { - dev_err(&spi->dev, - "Failed read WILC_VMM_TO_HOST_SIZE ...\n"); - return ret; - } - tmp = (byte_cnt >> 2) & IRQ_DMA_WD_CNT_MASK; - - j = 0; - do { - wilc_spi_read_reg(wilc, 0x1a90, &irq_flags); - tmp |= ((irq_flags >> 27) << IRG_FLAGS_OFFSET); - - if (spi_priv->nint > 5) { - wilc_spi_read_reg(wilc, 0x1a94, &irq_flags); - tmp |= (((irq_flags >> 0) & 0x7) << k); - } - - unknown_mask = ~((1ul << spi_priv->nint) - 1); - - unexpected_irq = (tmp >> IRG_FLAGS_OFFSET) & unknown_mask; - if (unexpected_irq) { - dev_err(&spi->dev, - "Unexpected interrupt(2):j=%d,tmp=%x,mask=%x\n", - j, tmp, unknown_mask); - } - - j++; - } while (unexpected_irq); - - *int_status = tmp; - - return ret; + return spi_internal_read(wilc, 0xe840 - WILC_SPI_REG_BASE, int_status); } static int wilc_spi_clear_int_ext(struct wilc *wilc, u32 val) { - struct spi_device *spi = to_spi_device(wilc->dev); - struct wilc_spi *spi_priv = wilc->bus_data; - int ret; - u32 flags; - u32 tbl_ctl; - - if (spi_priv->has_thrpt_enh) { - return spi_internal_write(wilc, 0xe844 - WILC_SPI_REG_BASE, - val); - } - - flags = val & (BIT(MAX_NUM_INT) - 1); - if (flags) { - int i; - - ret = 1; - for (i = 0; i < spi_priv->nint; i++) { - /* - * No matter what you write 1 or 0, - * it will clear interrupt. - */ - if (flags & 1) - ret = wilc_spi_write_reg(wilc, - 0x10c8 + i * 4, 1); - if (!ret) - break; - flags >>= 1; - } - if (!ret) { - dev_err(&spi->dev, - "Failed wilc_spi_write_reg, set reg %x ...\n", - 0x10c8 + i * 4); - return ret; - } - for (i = spi_priv->nint; i < MAX_NUM_INT; i++) { - if (flags & 1) - dev_err(&spi->dev, - "Unexpected interrupt cleared %d...\n", - i); - flags >>= 1; - } - } - - tbl_ctl = 0; - /* select VMM table 0 */ - if (val & SEL_VMM_TBL0) - tbl_ctl |= BIT(0); - /* select VMM table 1 */ - if (val & SEL_VMM_TBL1) - tbl_ctl |= BIT(1); - - ret = wilc_spi_write_reg(wilc, WILC_VMM_TBL_CTL, tbl_ctl); - if (!ret) { - dev_err(&spi->dev, "fail write reg vmm_tbl_ctl...\n"); - return ret; - } - - if (val & EN_VMM) { - /* - * enable vmm transfer. - */ - ret = wilc_spi_write_reg(wilc, WILC_VMM_CORE_CTL, 1); - if (!ret) { - dev_err(&spi->dev, "fail write reg vmm_core_ctl...\n"); - return ret; - } - } - - return ret; + return spi_internal_write(wilc, 0xe844 - WILC_SPI_REG_BASE, val); } static int wilc_spi_sync_ext(struct wilc *wilc, int nint) @@ -1065,7 +928,7 @@ static int wilc_spi_sync_ext(struct wilc *wilc, int nint) if (nint > MAX_NUM_INT) { dev_err(&spi->dev, "Too many interrupts (%d)...\n", nint); - return 0; + return -EINVAL; } spi_priv->nint = nint; @@ -1074,58 +937,58 @@ static int wilc_spi_sync_ext(struct wilc *wilc, int nint) * interrupt pin mux select */ ret = wilc_spi_read_reg(wilc, WILC_PIN_MUX_0, ®); - if (!ret) { + if (ret) { dev_err(&spi->dev, "Failed read reg (%08x)...\n", WILC_PIN_MUX_0); - return 0; + return ret; } reg |= BIT(8); ret = wilc_spi_write_reg(wilc, WILC_PIN_MUX_0, reg); - if (!ret) { + if (ret) { dev_err(&spi->dev, "Failed write reg (%08x)...\n", WILC_PIN_MUX_0); - return 0; + return ret; } /* * interrupt enable */ ret = wilc_spi_read_reg(wilc, WILC_INTR_ENABLE, ®); - if (!ret) { + if (ret) { dev_err(&spi->dev, "Failed read reg (%08x)...\n", WILC_INTR_ENABLE); - return 0; + return ret; } for (i = 0; (i < 5) && (nint > 0); i++, nint--) reg |= (BIT((27 + i))); ret = wilc_spi_write_reg(wilc, WILC_INTR_ENABLE, reg); - if (!ret) { + if (ret) { dev_err(&spi->dev, "Failed write reg (%08x)...\n", WILC_INTR_ENABLE); - return 0; + return ret; } if (nint) { ret = wilc_spi_read_reg(wilc, WILC_INTR2_ENABLE, ®); - if (!ret) { + if (ret) { dev_err(&spi->dev, "Failed read reg (%08x)...\n", WILC_INTR2_ENABLE); - return 0; + return ret; } for (i = 0; (i < 3) && (nint > 0); i++, nint--) reg |= BIT(i); ret = wilc_spi_read_reg(wilc, WILC_INTR2_ENABLE, ®); - if (!ret) { + if (ret) { dev_err(&spi->dev, "Failed write reg (%08x)...\n", WILC_INTR2_ENABLE); - return 0; + return ret; } } - return 1; + return 0; } /* Global spi HIF function table */ diff --git a/drivers/staging/wilc1000/wlan.c b/drivers/staging/wilc1000/wlan.c index d3de76126b78..601e4d1345d2 100644 --- a/drivers/staging/wilc1000/wlan.c +++ b/drivers/staging/wilc1000/wlan.c @@ -489,50 +489,44 @@ int wilc_wlan_handle_txq(struct wilc *wilc, u32 *txq_count) struct wilc_vif *vif; if (wilc->quit) - goto out; + goto out_update_cnt; mutex_lock(&wilc->txq_add_to_head_cs); tqe = wilc_wlan_txq_get_first(wilc); if (!tqe) - goto out; + goto out_unlock; dev = tqe->vif->ndev; wilc_wlan_txq_filter_dup_tcp_ack(dev); i = 0; sum = 0; - do { - if (tqe && (i < (WILC_VMM_TBL_SIZE - 1))) { - if (tqe->type == WILC_CFG_PKT) - vmm_sz = ETH_CONFIG_PKT_HDR_OFFSET; - - else if (tqe->type == WILC_NET_PKT) - vmm_sz = ETH_ETHERNET_HDR_OFFSET; - - else - vmm_sz = HOST_HDR_OFFSET; + while (tqe && (i < (WILC_VMM_TBL_SIZE - 1))) { + if (tqe->type == WILC_CFG_PKT) + vmm_sz = ETH_CONFIG_PKT_HDR_OFFSET; + else if (tqe->type == WILC_NET_PKT) + vmm_sz = ETH_ETHERNET_HDR_OFFSET; + else + vmm_sz = HOST_HDR_OFFSET; - vmm_sz += tqe->buffer_size; + vmm_sz += tqe->buffer_size; - if (vmm_sz & 0x3) - vmm_sz = (vmm_sz + 4) & ~0x3; + if (vmm_sz & 0x3) + vmm_sz = (vmm_sz + 4) & ~0x3; - if ((sum + vmm_sz) > WILC_TX_BUFF_SIZE) - break; + if ((sum + vmm_sz) > WILC_TX_BUFF_SIZE) + break; - vmm_table[i] = vmm_sz / 4; - if (tqe->type == WILC_CFG_PKT) - vmm_table[i] |= BIT(10); - cpu_to_le32s(&vmm_table[i]); + vmm_table[i] = vmm_sz / 4; + if (tqe->type == WILC_CFG_PKT) + vmm_table[i] |= BIT(10); + cpu_to_le32s(&vmm_table[i]); - i++; - sum += vmm_sz; - tqe = wilc_wlan_txq_get_next(wilc, tqe); - } else { - break; - } - } while (1); + i++; + sum += vmm_sz; + tqe = wilc_wlan_txq_get_next(wilc, tqe); + } if (i == 0) - goto out; + goto out_unlock; vmm_table[i] = 0x0; acquire_bus(wilc, WILC_BUS_ACQUIRE_AND_WAKEUP); @@ -540,7 +534,7 @@ int wilc_wlan_handle_txq(struct wilc *wilc, u32 *txq_count) func = wilc->hif_func; do { ret = func->hif_read_reg(wilc, WILC_HOST_TX_CTRL, ®); - if (!ret) + if (ret) break; if ((reg & 0x1) == 0) @@ -554,7 +548,7 @@ int wilc_wlan_handle_txq(struct wilc *wilc, u32 *txq_count) } } while (!wilc->quit); - if (!ret) + if (ret) goto out_release_bus; timeout = 200; @@ -563,16 +557,16 @@ int wilc_wlan_handle_txq(struct wilc *wilc, u32 *txq_count) WILC_VMM_TBL_RX_SHADOW_BASE, (u8 *)vmm_table, ((i + 1) * 4)); - if (!ret) + if (ret) break; ret = func->hif_write_reg(wilc, WILC_HOST_VMM_CTL, 0x2); - if (!ret) + if (ret) break; do { ret = func->hif_read_reg(wilc, WILC_HOST_VMM_CTL, ®); - if (!ret) + if (ret) break; if ((reg >> 2) & 0x1) { entries = ((reg >> 3) & 0x3f); @@ -585,27 +579,27 @@ int wilc_wlan_handle_txq(struct wilc *wilc, u32 *txq_count) break; } - if (!ret) + if (ret) break; if (entries == 0) { ret = func->hif_read_reg(wilc, WILC_HOST_TX_CTRL, ®); - if (!ret) + if (ret) break; reg &= ~BIT(0); ret = func->hif_write_reg(wilc, WILC_HOST_TX_CTRL, reg); - if (!ret) - break; - break; } - break; - } while (1); + } while (0); - if (!ret) + if (ret) goto out_release_bus; if (entries == 0) { - ret = -ENOBUFS; + /* + * No VMM space available in firmware so retry to transmit + * the packet from tx queue. + */ + ret = WILC_VMM_ENTRY_FULL_RETRY; goto out_release_bus; } @@ -664,7 +658,7 @@ int wilc_wlan_handle_txq(struct wilc *wilc, u32 *txq_count) acquire_bus(wilc, WILC_BUS_ACQUIRE_AND_WAKEUP); ret = func->hif_clear_int_ext(wilc, ENABLE_TX_VMM); - if (!ret) + if (ret) goto out_release_bus; ret = func->hif_block_tx_ext(wilc, 0, txb, offset); @@ -672,9 +666,10 @@ int wilc_wlan_handle_txq(struct wilc *wilc, u32 *txq_count) out_release_bus: release_bus(wilc, WILC_BUS_RELEASE_ALLOW_SLEEP); -out: +out_unlock: mutex_unlock(&wilc->txq_add_to_head_cs); +out_update_cnt: *txq_count = wilc->txq_entries; return ret; } @@ -725,9 +720,7 @@ static void wilc_wlan_handle_rx_buff(struct wilc *wilc, u8 *buffer, int size) } } offset += tp_len; - if (offset >= size) - break; - } while (1); + } while (offset < size); } static void wilc_wlan_handle_rxq(struct wilc *wilc) @@ -736,11 +729,7 @@ static void wilc_wlan_handle_rxq(struct wilc *wilc) u8 *buffer; struct rxq_entry_t *rqe; - do { - if (wilc->quit) { - complete(&wilc->cfg_event); - break; - } + while (!wilc->quit) { rqe = wilc_wlan_rxq_remove(wilc); if (!rqe) break; @@ -750,7 +739,9 @@ static void wilc_wlan_handle_rxq(struct wilc *wilc) wilc_wlan_handle_rx_buff(wilc, buffer, size); kfree(rqe); - } while (1); + } + if (wilc->quit) + complete(&wilc->cfg_event); } static void wilc_unknown_isr_ext(struct wilc *wilc) @@ -785,7 +776,7 @@ static void wilc_wlan_handle_isr_ext(struct wilc *wilc, u32 int_status) wilc->hif_func->hif_clear_int_ext(wilc, DATA_INT_CLR | ENABLE_RX_VMM); ret = wilc->hif_func->hif_block_rx_ext(wilc, 0, buffer, size); - if (!ret) + if (ret) return; offset += size; @@ -846,7 +837,7 @@ int wilc_wlan_firmware_download(struct wilc *wilc, const u8 *buffer, memcpy(dma_buffer, &buffer[offset], size2); ret = wilc->hif_func->hif_block_tx(wilc, addr, dma_buffer, size2); - if (!ret) + if (ret) break; addr += size2; @@ -855,17 +846,15 @@ int wilc_wlan_firmware_download(struct wilc *wilc, const u8 *buffer, } release_bus(wilc, WILC_BUS_RELEASE_ONLY); - if (!ret) { - ret = -EIO; + if (ret) goto fail; - } } while (offset < buffer_size); fail: kfree(dma_buffer); - return (ret < 0) ? ret : 0; + return ret; } int wilc_wlan_start(struct wilc *wilc) @@ -882,49 +871,26 @@ int wilc_wlan_start(struct wilc *wilc) } acquire_bus(wilc, WILC_BUS_ACQUIRE_ONLY); ret = wilc->hif_func->hif_write_reg(wilc, WILC_VMM_CORE_CFG, reg); - if (!ret) { + if (ret) { release_bus(wilc, WILC_BUS_RELEASE_ONLY); - return -EIO; + return ret; } reg = 0; if (wilc->io_type == WILC_HIF_SDIO && wilc->dev_irq_num) reg |= WILC_HAVE_SDIO_IRQ_GPIO; -#ifdef WILC_DISABLE_PMU -#else - reg |= WILC_HAVE_USE_PMU; -#endif - -#ifdef WILC_SLEEP_CLK_SRC_XO - reg |= WILC_HAVE_SLEEP_CLK_SRC_XO; -#elif defined WILC_SLEEP_CLK_SRC_RTC - reg |= WILC_HAVE_SLEEP_CLK_SRC_RTC; -#endif - -#ifdef WILC_EXT_PA_INV_TX_RX - reg |= WILC_HAVE_EXT_PA_INV_TX_RX; -#endif - reg |= WILC_HAVE_USE_IRQ_AS_HOST_WAKE; - reg |= WILC_HAVE_LEGACY_RF_SETTINGS; -#ifdef XTAL_24 - reg |= WILC_HAVE_XTAL_24; -#endif -#ifdef DISABLE_WILC_UART - reg |= WILC_HAVE_DISABLE_WILC_UART; -#endif - ret = wilc->hif_func->hif_write_reg(wilc, WILC_GP_REG_1, reg); - if (!ret) { + if (ret) { release_bus(wilc, WILC_BUS_RELEASE_ONLY); - return -EIO; + return ret; } wilc->hif_func->hif_sync_ext(wilc, NUM_INT_EXT); ret = wilc->hif_func->hif_read_reg(wilc, 0x1000, &chipid); - if (!ret) { + if (ret) { release_bus(wilc, WILC_BUS_RELEASE_ONLY); - return -EIO; + return ret; } wilc->hif_func->hif_read_reg(wilc, WILC_GLB_RESET_0, ®); @@ -939,7 +905,7 @@ int wilc_wlan_start(struct wilc *wilc) wilc->hif_func->hif_read_reg(wilc, WILC_GLB_RESET_0, ®); release_bus(wilc, WILC_BUS_RELEASE_ONLY); - return (ret < 0) ? ret : 0; + return ret; } int wilc_wlan_stop(struct wilc *wilc, struct wilc_vif *vif) @@ -950,33 +916,33 @@ int wilc_wlan_stop(struct wilc *wilc, struct wilc_vif *vif) acquire_bus(wilc, WILC_BUS_ACQUIRE_AND_WAKEUP); ret = wilc->hif_func->hif_read_reg(wilc, WILC_GP_REG_0, ®); - if (!ret) { + if (ret) { netdev_err(vif->ndev, "Error while reading reg\n"); release_bus(wilc, WILC_BUS_RELEASE_ALLOW_SLEEP); - return -EIO; + return ret; } ret = wilc->hif_func->hif_write_reg(wilc, WILC_GP_REG_0, (reg | WILC_ABORT_REQ_BIT)); - if (!ret) { + if (ret) { netdev_err(vif->ndev, "Error while writing reg\n"); release_bus(wilc, WILC_BUS_RELEASE_ALLOW_SLEEP); - return -EIO; + return ret; } ret = wilc->hif_func->hif_read_reg(wilc, WILC_FW_HOST_COMM, ®); - if (!ret) { + if (ret) { netdev_err(vif->ndev, "Error while reading reg\n"); release_bus(wilc, WILC_BUS_RELEASE_ALLOW_SLEEP); - return -EIO; + return ret; } reg = BIT(0); ret = wilc->hif_func->hif_write_reg(wilc, WILC_FW_HOST_COMM, reg); - if (!ret) { + if (ret) { netdev_err(vif->ndev, "Error while writing reg\n"); release_bus(wilc, WILC_BUS_RELEASE_ALLOW_SLEEP); - return -EIO; + return ret; } release_bus(wilc, WILC_BUS_RELEASE_ALLOW_SLEEP); @@ -992,21 +958,14 @@ void wilc_wlan_cleanup(struct net_device *dev) struct wilc *wilc = vif->wilc; wilc->quit = 1; - do { - tqe = wilc_wlan_txq_remove_from_head(dev); - if (!tqe) - break; + while ((tqe = wilc_wlan_txq_remove_from_head(dev))) { if (tqe->tx_complete_func) tqe->tx_complete_func(tqe->priv, 0); kfree(tqe); - } while (1); + } - do { - rqe = wilc_wlan_rxq_remove(wilc); - if (!rqe) - break; + while ((rqe = wilc_wlan_rxq_remove(wilc))) kfree(rqe); - } while (1); kfree(wilc->rx_buffer); wilc->rx_buffer = NULL; @@ -1156,10 +1115,11 @@ int wilc_send_config_pkt(struct wilc_vif *vif, u8 mode, struct wid *wids, return ret; } -static u32 init_chip(struct net_device *dev) +static int init_chip(struct net_device *dev) { u32 chipid; - u32 reg, ret = 0; + u32 reg; + int ret = 0; struct wilc_vif *vif = netdev_priv(dev); struct wilc *wilc = vif->wilc; @@ -1169,18 +1129,18 @@ static u32 init_chip(struct net_device *dev) if ((chipid & 0xfff) != 0xa0) { ret = wilc->hif_func->hif_read_reg(wilc, 0x1118, ®); - if (!ret) { + if (ret) { netdev_err(dev, "fail read reg 0x1118\n"); goto release; } reg |= BIT(0); ret = wilc->hif_func->hif_write_reg(wilc, 0x1118, reg); - if (!ret) { + if (ret) { netdev_err(dev, "fail write reg 0x1118\n"); goto release; } ret = wilc->hif_func->hif_write_reg(wilc, 0xc0000, 0x71); - if (!ret) { + if (ret) { netdev_err(dev, "fail write reg 0xc0000\n"); goto release; } @@ -1230,7 +1190,7 @@ int wilc_wlan_init(struct net_device *dev) wilc->quit = 0; - if (!wilc->hif_func->hif_init(wilc, false)) { + if (wilc->hif_func->hif_init(wilc, false)) { ret = -EIO; goto fail; } @@ -1251,12 +1211,12 @@ int wilc_wlan_init(struct net_device *dev) goto fail; } - if (!init_chip(dev)) { + if (init_chip(dev)) { ret = -EIO; goto fail; } - return 1; + return 0; fail: diff --git a/drivers/staging/wilc1000/wlan.h b/drivers/staging/wilc1000/wlan.h index 1f6957cf2e9c..8c4634262adb 100644 --- a/drivers/staging/wilc1000/wlan.h +++ b/drivers/staging/wilc1000/wlan.h @@ -197,6 +197,8 @@ #define IS_MANAGMEMENT_CALLBACK 0x080 #define IS_MGMT_STATUS_SUCCES 0x040 +#define WILC_WID_TYPE GENMASK(15, 12) +#define WILC_VMM_ENTRY_FULL_RETRY 1 /******************************************** * * Tx/Rx Queue Structure diff --git a/drivers/staging/wilc1000/wlan_cfg.c b/drivers/staging/wilc1000/wlan_cfg.c index 6f6b286788d1..fe2a7ed8e5cd 100644 --- a/drivers/staging/wilc1000/wlan_cfg.c +++ b/drivers/staging/wilc1000/wlan_cfg.c @@ -4,6 +4,7 @@ * All rights reserved. */ +#include <linux/bitfield.h> #include "wlan_if.h" #include "wlan.h" #include "wlan_cfg.h" @@ -132,75 +133,54 @@ static int wilc_wlan_cfg_set_bin(u8 *frame, u32 offset, u16 id, u8 *b, u32 size) * ********************************************/ -#define GET_WID_TYPE(wid) (((wid) >> 12) & 0x7) static void wilc_wlan_parse_response_frame(struct wilc *wl, u8 *info, int size) { u16 wid; u32 len = 0, i = 0; + struct wilc_cfg *cfg = &wl->cfg; while (size > 0) { i = 0; wid = get_unaligned_le16(info); - switch (GET_WID_TYPE(wid)) { + switch (FIELD_GET(WILC_WID_TYPE, wid)) { case WID_CHAR: - do { - if (wl->cfg.b[i].id == WID_NIL) - break; - - if (wl->cfg.b[i].id == wid) { - wl->cfg.b[i].val = info[4]; - break; - } + while (cfg->b[i].id != WID_NIL && cfg->b[i].id != wid) i++; - } while (1); + + if (cfg->b[i].id == wid) + cfg->b[i].val = info[4]; + len = 3; break; case WID_SHORT: - do { - struct wilc_cfg_hword *hw = &wl->cfg.hw[i]; + while (cfg->hw[i].id != WID_NIL && cfg->hw[i].id != wid) + i++; - if (hw->id == WID_NIL) - break; + if (cfg->hw[i].id == wid) + cfg->hw[i].val = get_unaligned_le16(&info[4]); - if (hw->id == wid) { - hw->val = get_unaligned_le16(&info[4]); - break; - } - i++; - } while (1); len = 4; break; case WID_INT: - do { - struct wilc_cfg_word *w = &wl->cfg.w[i]; + while (cfg->w[i].id != WID_NIL && cfg->w[i].id != wid) + i++; - if (w->id == WID_NIL) - break; + if (cfg->w[i].id == wid) + cfg->w[i].val = get_unaligned_le32(&info[4]); - if (w->id == wid) { - w->val = get_unaligned_le32(&info[4]); - break; - } - i++; - } while (1); len = 6; break; case WID_STR: - do { - if (wl->cfg.s[i].id == WID_NIL) - break; - - if (wl->cfg.s[i].id == wid) { - memcpy(wl->cfg.s[i].str, &info[2], - (info[2] + 2)); - break; - } + while (cfg->s[i].id != WID_NIL && cfg->s[i].id != wid) i++; - } while (1); + + if (cfg->s[i].id == wid) + memcpy(cfg->s[i].str, &info[2], info[2] + 2); + len = 2 + info[2]; break; @@ -223,16 +203,12 @@ static void wilc_wlan_parse_info_frame(struct wilc *wl, u8 *info) if (len == 1 && wid == WID_STATUS) { int i = 0; - do { - if (wl->cfg.b[i].id == WID_NIL) - break; - - if (wl->cfg.b[i].id == wid) { - wl->cfg.b[i].val = info[3]; - break; - } + while (wl->cfg.b[i].id != WID_NIL && + wl->cfg.b[i].id != wid) i++; - } while (1); + + if (wl->cfg.b[i].id == wid) + wl->cfg.b[i].val = info[3]; } } @@ -244,7 +220,7 @@ static void wilc_wlan_parse_info_frame(struct wilc *wl, u8 *info) int wilc_wlan_cfg_set_wid(u8 *frame, u32 offset, u16 id, u8 *buf, int size) { - u8 type = (id >> 12) & 0xf; + u8 type = FIELD_GET(WILC_WID_TYPE, id); int ret = 0; switch (type) { @@ -290,65 +266,47 @@ int wilc_wlan_cfg_get_wid(u8 *frame, u32 offset, u16 id) int wilc_wlan_cfg_get_val(struct wilc *wl, u16 wid, u8 *buffer, u32 buffer_size) { - u32 type = (wid >> 12) & 0xf; + u8 type = FIELD_GET(WILC_WID_TYPE, wid); int i, ret = 0; + struct wilc_cfg *cfg = &wl->cfg; i = 0; if (type == CFG_BYTE_CMD) { - do { - if (wl->cfg.b[i].id == WID_NIL) - break; - - if (wl->cfg.b[i].id == wid) { - memcpy(buffer, &wl->cfg.b[i].val, 1); - ret = 1; - break; - } + while (cfg->b[i].id != WID_NIL && cfg->b[i].id != wid) i++; - } while (1); + + if (cfg->b[i].id == wid) { + memcpy(buffer, &cfg->b[i].val, 1); + ret = 1; + } } else if (type == CFG_HWORD_CMD) { - do { - if (wl->cfg.hw[i].id == WID_NIL) - break; - - if (wl->cfg.hw[i].id == wid) { - memcpy(buffer, &wl->cfg.hw[i].val, 2); - ret = 2; - break; - } + while (cfg->hw[i].id != WID_NIL && cfg->hw[i].id != wid) i++; - } while (1); + + if (cfg->hw[i].id == wid) { + memcpy(buffer, &cfg->hw[i].val, 2); + ret = 2; + } } else if (type == CFG_WORD_CMD) { - do { - if (wl->cfg.w[i].id == WID_NIL) - break; - - if (wl->cfg.w[i].id == wid) { - memcpy(buffer, &wl->cfg.w[i].val, 4); - ret = 4; - break; - } + while (cfg->w[i].id != WID_NIL && cfg->w[i].id != wid) i++; - } while (1); - } else if (type == CFG_STR_CMD) { - do { - u32 id = wl->cfg.s[i].id; - if (id == WID_NIL) - break; + if (cfg->w[i].id == wid) { + memcpy(buffer, &cfg->w[i].val, 4); + ret = 4; + } + } else if (type == CFG_STR_CMD) { + while (cfg->s[i].id != WID_NIL && cfg->s[i].id != wid) + i++; - if (id == wid) { - u16 size = get_unaligned_le16(wl->cfg.s[i].str); + if (cfg->s[i].id == wid) { + u16 size = get_unaligned_le16(cfg->s[i].str); - if (buffer_size >= size) { - memcpy(buffer, &wl->cfg.s[i].str[2], - size); - ret = size; - } - break; + if (buffer_size >= size) { + memcpy(buffer, &cfg->s[i].str[2], size); + ret = size; } - i++; - } while (1); + } } return ret; } diff --git a/drivers/staging/wilc1000/wlan_if.h b/drivers/staging/wilc1000/wlan_if.h index 7c7ee66c35f5..f85fd575136d 100644 --- a/drivers/staging/wilc1000/wlan_if.h +++ b/drivers/staging/wilc1000/wlan_if.h @@ -8,6 +8,7 @@ #define WILC_WLAN_IF_H #include <linux/netdevice.h> +#include "fw.h" /******************************************** * diff --git a/drivers/staging/wlan-ng/prism2mgmt.c b/drivers/staging/wlan-ng/prism2mgmt.c index 7350fe5d96a3..a8860d2aee68 100644 --- a/drivers/staging/wlan-ng/prism2mgmt.c +++ b/drivers/staging/wlan-ng/prism2mgmt.c @@ -959,7 +959,7 @@ int prism2mgmt_flashdl_state(struct wlandevice *wlandev, void *msgp) } } - return 0; + return result; } /*---------------------------------------------------------------- diff --git a/include/linux/b1pcmcia.h b/include/linux/b1pcmcia.h deleted file mode 100644 index 12a867c6061e..000000000000 --- a/include/linux/b1pcmcia.h +++ /dev/null @@ -1,21 +0,0 @@ -/* $Id: b1pcmcia.h,v 1.1.8.2 2001/09/23 22:25:05 kai Exp $ - * - * Exported functions of module b1pcmcia to be called by - * avm_cs card services module. - * - * Copyright 1999 by Carsten Paeth (calle@calle.in-berlin.de) - * - * This software may be used and distributed according to the terms - * of the GNU General Public License, incorporated herein by reference. - * - */ - -#ifndef _B1PCMCIA_H_ -#define _B1PCMCIA_H_ - -int b1pcmcia_addcard_b1(unsigned int port, unsigned irq); -int b1pcmcia_addcard_m1(unsigned int port, unsigned irq); -int b1pcmcia_addcard_m2(unsigned int port, unsigned irq); -int b1pcmcia_delcard(unsigned int port, unsigned irq); - -#endif /* _B1PCMCIA_H_ */ diff --git a/include/linux/iio/accel/kxcjk_1013.h b/include/linux/iio/accel/kxcjk_1013.h index 8c3c78bc9f91..ea0ecb774371 100644 --- a/include/linux/iio/accel/kxcjk_1013.h +++ b/include/linux/iio/accel/kxcjk_1013.h @@ -7,8 +7,11 @@ #ifndef __IIO_KXCJK_1013_H__ #define __IIO_KXCJK_1013_H__ +#include <linux/iio/iio.h> + struct kxcjk_1013_platform_data { bool active_high_intr; + struct iio_mount_matrix orientation; }; #endif diff --git a/include/linux/iio/adc/ad_sigma_delta.h b/include/linux/iio/adc/ad_sigma_delta.h index 8a4e25a7080c..5a127c0ed200 100644 --- a/include/linux/iio/adc/ad_sigma_delta.h +++ b/include/linux/iio/adc/ad_sigma_delta.h @@ -40,6 +40,7 @@ struct iio_dev; * @read_mask: Mask for the communications register having the read bit set. * @data_reg: Address of the data register, if 0 the default address of 0x3 will * be used. + * @irq_flags: flags for the interrupt used by the triggered buffer */ struct ad_sigma_delta_info { int (*set_channel)(struct ad_sigma_delta *, unsigned int channel); @@ -49,6 +50,7 @@ struct ad_sigma_delta_info { unsigned int addr_shift; unsigned int read_mask; unsigned int data_reg; + unsigned long irq_flags; }; /** diff --git a/include/linux/iio/buffer_impl.h b/include/linux/iio/buffer_impl.h index d1171db23742..a4d2d8061ef6 100644 --- a/include/linux/iio/buffer_impl.h +++ b/include/linux/iio/buffer_impl.h @@ -18,7 +18,7 @@ struct iio_buffer; /** * struct iio_buffer_access_funcs - access functions for buffers. * @store_to: actually store stuff to the buffer - * @read_first_n: try to get a specified number of bytes (must exist) + * @read: try to get a specified number of bytes (must exist) * @data_available: indicates how much data is available for reading from * the buffer. * @request_update: if a parameter change has been marked, update underlying @@ -45,9 +45,7 @@ struct iio_buffer; **/ struct iio_buffer_access_funcs { int (*store_to)(struct iio_buffer *buffer, const void *data); - int (*read_first_n)(struct iio_buffer *buffer, - size_t n, - char __user *buf); + int (*read)(struct iio_buffer *buffer, size_t n, char __user *buf); size_t (*data_available)(struct iio_buffer *buffer); int (*request_update)(struct iio_buffer *buffer); diff --git a/include/linux/iio/common/st_sensors.h b/include/linux/iio/common/st_sensors.h index 686be532f4cb..33e939977444 100644 --- a/include/linux/iio/common/st_sensors.h +++ b/include/linux/iio/common/st_sensors.h @@ -315,16 +315,6 @@ ssize_t st_sensors_sysfs_sampling_frequency_avail(struct device *dev, ssize_t st_sensors_sysfs_scale_avail(struct device *dev, struct device_attribute *attr, char *buf); -#ifdef CONFIG_OF -void st_sensors_of_name_probe(struct device *dev, - const struct of_device_id *match, - char *name, int len); -#else -static inline void st_sensors_of_name_probe(struct device *dev, - const struct of_device_id *match, - char *name, int len) -{ -} -#endif +void st_sensors_dev_name_probe(struct device *dev, char *name, int len); #endif /* ST_SENSORS_H */ diff --git a/include/linux/iio/common/st_sensors_i2c.h b/include/linux/iio/common/st_sensors_i2c.h index 01e424e2af4f..5f15cf01036c 100644 --- a/include/linux/iio/common/st_sensors_i2c.h +++ b/include/linux/iio/common/st_sensors_i2c.h @@ -12,18 +12,8 @@ #include <linux/i2c.h> #include <linux/iio/common/st_sensors.h> -#include <linux/of.h> int st_sensors_i2c_configure(struct iio_dev *indio_dev, struct i2c_client *client); -#ifdef CONFIG_ACPI -int st_sensors_match_acpi_device(struct device *dev); -#else -static inline int st_sensors_match_acpi_device(struct device *dev) -{ - return -ENODEV; -} -#endif - #endif /* ST_SENSORS_I2C_H */ diff --git a/include/linux/iio/frequency/adf4350.h b/include/linux/iio/frequency/adf4350.h index ce9490bfeb89..de45cf2ee1e4 100644 --- a/include/linux/iio/frequency/adf4350.h +++ b/include/linux/iio/frequency/adf4350.h @@ -103,9 +103,6 @@ * @r2_user_settings: User defined settings for ADF4350/1 REGISTER_2. * @r3_user_settings: User defined settings for ADF4350/1 REGISTER_3. * @r4_user_settings: User defined settings for ADF4350/1 REGISTER_4. - * @gpio_lock_detect: Optional, if set with a valid GPIO number, - * pll lock state is tested upon read. - * If not used - set to -1. */ struct adf4350_platform_data { @@ -121,7 +118,6 @@ struct adf4350_platform_data { unsigned r2_user_settings; unsigned r3_user_settings; unsigned r4_user_settings; - int gpio_lock_detect; }; #endif /* IIO_PLL_ADF4350_H_ */ diff --git a/include/linux/iio/imu/adis.h b/include/linux/iio/imu/adis.h index 92aae14593bf..d2fcf45b4cef 100644 --- a/include/linux/iio/imu/adis.h +++ b/include/linux/iio/imu/adis.h @@ -23,6 +23,17 @@ struct adis; struct adis_burst; /** + * struct adis_timeouts - ADIS chip variant timeouts + * @reset_ms - Wait time after rst pin goes inactive + * @sw_reset_ms - Wait time after sw reset command + * @self_test_ms - Wait time after self test command + */ +struct adis_timeout { + u16 reset_ms; + u16 sw_reset_ms; + u16 self_test_ms; +}; +/** * struct adis_data - ADIS chip variant specific data * @read_delay: SPI delay for read operations in us * @write_delay: SPI delay for write operations in us @@ -32,6 +43,7 @@ struct adis_burst; * @diag_stat_reg: Register address of the DIAG_STAT register * @status_error_msgs: Array of error messgaes * @status_error_mask: + * @timeouts: Chip specific delays */ struct adis_data { unsigned int read_delay; @@ -44,7 +56,7 @@ struct adis_data { unsigned int self_test_mask; bool self_test_no_autoclear; - unsigned int startup_delay; + const struct adis_timeout *timeouts; const char * const *status_error_msgs; unsigned int status_error_mask; @@ -61,7 +73,7 @@ struct adis { const struct adis_data *data; struct adis_burst *burst; - struct mutex txrx_lock; + struct mutex state_lock; struct spi_message msg; struct spi_transfer *xfer; unsigned int current_page; @@ -73,14 +85,143 @@ struct adis { int adis_init(struct adis *adis, struct iio_dev *indio_dev, struct spi_device *spi, const struct adis_data *data); -int adis_reset(struct adis *adis); +int __adis_reset(struct adis *adis); + +/** + * adis_reset() - Reset the device + * @adis: The adis device + * + * Returns 0 on success, a negative error code otherwise + */ +static inline int adis_reset(struct adis *adis) +{ + int ret; + + mutex_lock(&adis->state_lock); + ret = __adis_reset(adis); + mutex_unlock(&adis->state_lock); + + return ret; +} -int adis_write_reg(struct adis *adis, unsigned int reg, +int __adis_write_reg(struct adis *adis, unsigned int reg, unsigned int val, unsigned int size); -int adis_read_reg(struct adis *adis, unsigned int reg, +int __adis_read_reg(struct adis *adis, unsigned int reg, unsigned int *val, unsigned int size); /** + * __adis_write_reg_8() - Write single byte to a register (unlocked) + * @adis: The adis device + * @reg: The address of the register to be written + * @value: The value to write + */ +static inline int __adis_write_reg_8(struct adis *adis, unsigned int reg, + uint8_t val) +{ + return __adis_write_reg(adis, reg, val, 1); +} + +/** + * __adis_write_reg_16() - Write 2 bytes to a pair of registers (unlocked) + * @adis: The adis device + * @reg: The address of the lower of the two registers + * @value: Value to be written + */ +static inline int __adis_write_reg_16(struct adis *adis, unsigned int reg, + uint16_t val) +{ + return __adis_write_reg(adis, reg, val, 2); +} + +/** + * __adis_write_reg_32() - write 4 bytes to four registers (unlocked) + * @adis: The adis device + * @reg: The address of the lower of the four register + * @value: Value to be written + */ +static inline int __adis_write_reg_32(struct adis *adis, unsigned int reg, + uint32_t val) +{ + return __adis_write_reg(adis, reg, val, 4); +} + +/** + * __adis_read_reg_16() - read 2 bytes from a 16-bit register (unlocked) + * @adis: The adis device + * @reg: The address of the lower of the two registers + * @val: The value read back from the device + */ +static inline int __adis_read_reg_16(struct adis *adis, unsigned int reg, + uint16_t *val) +{ + unsigned int tmp; + int ret; + + ret = __adis_read_reg(adis, reg, &tmp, 2); + if (ret == 0) + *val = tmp; + + return ret; +} + +/** + * __adis_read_reg_32() - read 4 bytes from a 32-bit register (unlocked) + * @adis: The adis device + * @reg: The address of the lower of the two registers + * @val: The value read back from the device + */ +static inline int __adis_read_reg_32(struct adis *adis, unsigned int reg, + uint32_t *val) +{ + unsigned int tmp; + int ret; + + ret = __adis_read_reg(adis, reg, &tmp, 4); + if (ret == 0) + *val = tmp; + + return ret; +} + +/** + * adis_write_reg() - write N bytes to register + * @adis: The adis device + * @reg: The address of the lower of the two registers + * @value: The value to write to device (up to 4 bytes) + * @size: The size of the @value (in bytes) + */ +static inline int adis_write_reg(struct adis *adis, unsigned int reg, + unsigned int val, unsigned int size) +{ + int ret; + + mutex_lock(&adis->state_lock); + ret = __adis_write_reg(adis, reg, val, size); + mutex_unlock(&adis->state_lock); + + return ret; +} + +/** + * adis_read_reg() - read N bytes from register + * @adis: The adis device + * @reg: The address of the lower of the two registers + * @val: The value read back from the device + * @size: The size of the @val buffer + */ +static int adis_read_reg(struct adis *adis, unsigned int reg, + unsigned int *val, unsigned int size) +{ + int ret; + + mutex_lock(&adis->state_lock); + ret = __adis_read_reg(adis, reg, val, size); + mutex_unlock(&adis->state_lock); + + return ret; +} + +/** * adis_write_reg_8() - Write single byte to a register * @adis: The adis device * @reg: The address of the register to be written @@ -155,7 +296,18 @@ static inline int adis_read_reg_32(struct adis *adis, unsigned int reg, } int adis_enable_irq(struct adis *adis, bool enable); -int adis_check_status(struct adis *adis); +int __adis_check_status(struct adis *adis); + +static inline int adis_check_status(struct adis *adis) +{ + int ret; + + mutex_lock(&adis->state_lock); + ret = __adis_check_status(adis); + mutex_unlock(&adis->state_lock); + + return ret; +} int adis_initial_startup(struct adis *adis); diff --git a/include/linux/iio/magnetometer/ak8975.h b/include/linux/iio/magnetometer/ak8975.h deleted file mode 100644 index ac9366f807cb..000000000000 --- a/include/linux/iio/magnetometer/ak8975.h +++ /dev/null @@ -1,17 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0 */ -#ifndef __IIO_MAGNETOMETER_AK8975_H__ -#define __IIO_MAGNETOMETER_AK8975_H__ - -#include <linux/iio/iio.h> - -/** - * struct ak8975_platform_data - AK8975 magnetometer driver platform data - * @eoc_gpio: data ready event gpio - * @orientation: mounting matrix relative to main hardware - */ -struct ak8975_platform_data { - int eoc_gpio; - struct iio_mount_matrix orientation; -}; - -#endif diff --git a/include/linux/iio/types.h b/include/linux/iio/types.h index fa824e160f35..e6fd3645963c 100644 --- a/include/linux/iio/types.h +++ b/include/linux/iio/types.h @@ -25,6 +25,7 @@ enum iio_event_info { #define IIO_VAL_INT_MULTIPLE 5 #define IIO_VAL_FRACTIONAL 10 #define IIO_VAL_FRACTIONAL_LOG2 11 +#define IIO_VAL_CHAR 12 enum iio_available_type { IIO_AVAIL_LIST, @@ -57,6 +58,7 @@ enum iio_chan_info_enum { IIO_CHAN_INFO_DEBOUNCE_TIME, IIO_CHAN_INFO_CALIBEMISSIVITY, IIO_CHAN_INFO_OVERSAMPLING_RATIO, + IIO_CHAN_INFO_THERMOCOUPLE_TYPE, }; #endif /* _IIO_TYPES_H_ */ diff --git a/include/linux/isdn/capilli.h b/include/linux/isdn/capilli.h index d75e1ad72964..12be09b6883b 100644 --- a/include/linux/isdn/capilli.h +++ b/include/linux/isdn/capilli.h @@ -69,7 +69,6 @@ struct capi_ctr { unsigned short state; /* controller state */ int blocked; /* output blocked */ int traceflag; /* capi trace */ - wait_queue_head_t state_wait_queue; struct proc_dir_entry *procent; char procfn[128]; @@ -80,8 +79,6 @@ int detach_capi_ctr(struct capi_ctr *); void capi_ctr_ready(struct capi_ctr * card); void capi_ctr_down(struct capi_ctr * card); -void capi_ctr_suspend_output(struct capi_ctr * card); -void capi_ctr_resume_output(struct capi_ctr * card); void capi_ctr_handle_message(struct capi_ctr * card, u16 appl, struct sk_buff *skb); // --------------------------------------------------------------------------- @@ -91,23 +88,8 @@ struct capi_driver { char name[32]; /* driver name */ char revision[32]; - int (*add_card)(struct capi_driver *driver, capicardparams *data); - /* management information for kcapi */ struct list_head list; }; -void register_capi_driver(struct capi_driver *driver); -void unregister_capi_driver(struct capi_driver *driver); - -// --------------------------------------------------------------------------- -// library functions for use by hardware controller drivers - -void capilib_new_ncci(struct list_head *head, u16 applid, u32 ncci, u32 winsize); -void capilib_free_ncci(struct list_head *head, u16 applid, u32 ncci); -void capilib_release_appl(struct list_head *head, u16 applid); -void capilib_release(struct list_head *head); -void capilib_data_b3_conf(struct list_head *head, u16 applid, u32 ncci, u16 msgid); -u16 capilib_data_b3_req(struct list_head *head, u16 applid, u32 ncci, u16 msgid); - #endif /* __CAPILLI_H__ */ diff --git a/include/linux/isdn/capiutil.h b/include/linux/isdn/capiutil.h index 44bd6046e6e2..953fd500dff7 100644 --- a/include/linux/isdn/capiutil.h +++ b/include/linux/isdn/capiutil.h @@ -57,460 +57,4 @@ static inline void capimsg_setu32(void *m, int off, __u32 val) #define CAPIMSG_SETCONTROL(m, contr) capimsg_setu32(m, 8, contr) #define CAPIMSG_SETDATALEN(m, len) capimsg_setu16(m, 16, len) -/*----- basic-type definitions -----*/ - -typedef __u8 *_cstruct; - -typedef enum { - CAPI_COMPOSE, - CAPI_DEFAULT -} _cmstruct; - -/* - The _cmsg structure contains all possible CAPI 2.0 parameter. - All parameters are stored here first. The function CAPI_CMSG_2_MESSAGE - assembles the parameter and builds CAPI2.0 conform messages. - CAPI_MESSAGE_2_CMSG disassembles CAPI 2.0 messages and stores the - parameter in the _cmsg structure - */ - -typedef struct { - /* Header */ - __u16 ApplId; - __u8 Command; - __u8 Subcommand; - __u16 Messagenumber; - - /* Parameter */ - union { - __u32 adrController; - __u32 adrPLCI; - __u32 adrNCCI; - } adr; - - _cmstruct AdditionalInfo; - _cstruct B1configuration; - __u16 B1protocol; - _cstruct B2configuration; - __u16 B2protocol; - _cstruct B3configuration; - __u16 B3protocol; - _cstruct BC; - _cstruct BChannelinformation; - _cmstruct BProtocol; - _cstruct CalledPartyNumber; - _cstruct CalledPartySubaddress; - _cstruct CallingPartyNumber; - _cstruct CallingPartySubaddress; - __u32 CIPmask; - __u32 CIPmask2; - __u16 CIPValue; - __u32 Class; - _cstruct ConnectedNumber; - _cstruct ConnectedSubaddress; - __u32 Data; - __u16 DataHandle; - __u16 DataLength; - _cstruct FacilityConfirmationParameter; - _cstruct Facilitydataarray; - _cstruct FacilityIndicationParameter; - _cstruct FacilityRequestParameter; - __u16 FacilitySelector; - __u16 Flags; - __u32 Function; - _cstruct HLC; - __u16 Info; - _cstruct InfoElement; - __u32 InfoMask; - __u16 InfoNumber; - _cstruct Keypadfacility; - _cstruct LLC; - _cstruct ManuData; - __u32 ManuID; - _cstruct NCPI; - __u16 Reason; - __u16 Reason_B3; - __u16 Reject; - _cstruct Useruserdata; - - /* intern */ - unsigned l, p; - unsigned char *par; - __u8 *m; - - /* buffer to construct message */ - __u8 buf[180]; - -} _cmsg; - -/* - * capi_cmsg2message() assembles the parameter from _cmsg to a CAPI 2.0 - * conform message - */ -unsigned capi_cmsg2message(_cmsg * cmsg, __u8 * msg); - -/* - * capi_message2cmsg disassembles a CAPI message an writes the parameter - * into _cmsg for easy access - */ -unsigned capi_message2cmsg(_cmsg * cmsg, __u8 * msg); - -/* - * capi_cmsg_header() fills the _cmsg structure with default values, so only - * parameter with non default values must be changed before sending the - * message. - */ -unsigned capi_cmsg_header(_cmsg * cmsg, __u16 _ApplId, - __u8 _Command, __u8 _Subcommand, - __u16 _Messagenumber, __u32 _Controller); - -/*-----------------------------------------------------------------------*/ - -/* - * Debugging / Tracing functions - */ - -char *capi_cmd2str(__u8 cmd, __u8 subcmd); - -typedef struct { - u_char *buf; - u_char *p; - size_t size; - size_t pos; -} _cdebbuf; - -#define CDEBUG_SIZE 1024 -#define CDEBUG_GSIZE 4096 - -void cdebbuf_free(_cdebbuf *cdb); -int cdebug_init(void); -void cdebug_exit(void); - -_cdebbuf *capi_cmsg2str(_cmsg *cmsg); -_cdebbuf *capi_message2str(__u8 *msg); - -/*-----------------------------------------------------------------------*/ - -static inline void capi_cmsg_answer(_cmsg * cmsg) -{ - cmsg->Subcommand |= 0x01; -} - -/*-----------------------------------------------------------------------*/ - -static inline void capi_fill_CONNECT_B3_REQ(_cmsg * cmsg, __u16 ApplId, __u16 Messagenumber, - __u32 adr, - _cstruct NCPI) -{ - capi_cmsg_header(cmsg, ApplId, 0x82, 0x80, Messagenumber, adr); - cmsg->NCPI = NCPI; -} - -static inline void capi_fill_FACILITY_REQ(_cmsg * cmsg, __u16 ApplId, __u16 Messagenumber, - __u32 adr, - __u16 FacilitySelector, - _cstruct FacilityRequestParameter) -{ - capi_cmsg_header(cmsg, ApplId, 0x80, 0x80, Messagenumber, adr); - cmsg->FacilitySelector = FacilitySelector; - cmsg->FacilityRequestParameter = FacilityRequestParameter; -} - -static inline void capi_fill_INFO_REQ(_cmsg * cmsg, __u16 ApplId, __u16 Messagenumber, - __u32 adr, - _cstruct CalledPartyNumber, - _cstruct BChannelinformation, - _cstruct Keypadfacility, - _cstruct Useruserdata, - _cstruct Facilitydataarray) -{ - capi_cmsg_header(cmsg, ApplId, 0x08, 0x80, Messagenumber, adr); - cmsg->CalledPartyNumber = CalledPartyNumber; - cmsg->BChannelinformation = BChannelinformation; - cmsg->Keypadfacility = Keypadfacility; - cmsg->Useruserdata = Useruserdata; - cmsg->Facilitydataarray = Facilitydataarray; -} - -static inline void capi_fill_LISTEN_REQ(_cmsg * cmsg, __u16 ApplId, __u16 Messagenumber, - __u32 adr, - __u32 InfoMask, - __u32 CIPmask, - __u32 CIPmask2, - _cstruct CallingPartyNumber, - _cstruct CallingPartySubaddress) -{ - capi_cmsg_header(cmsg, ApplId, 0x05, 0x80, Messagenumber, adr); - cmsg->InfoMask = InfoMask; - cmsg->CIPmask = CIPmask; - cmsg->CIPmask2 = CIPmask2; - cmsg->CallingPartyNumber = CallingPartyNumber; - cmsg->CallingPartySubaddress = CallingPartySubaddress; -} - -static inline void capi_fill_ALERT_REQ(_cmsg * cmsg, __u16 ApplId, __u16 Messagenumber, - __u32 adr, - _cstruct BChannelinformation, - _cstruct Keypadfacility, - _cstruct Useruserdata, - _cstruct Facilitydataarray) -{ - capi_cmsg_header(cmsg, ApplId, 0x01, 0x80, Messagenumber, adr); - cmsg->BChannelinformation = BChannelinformation; - cmsg->Keypadfacility = Keypadfacility; - cmsg->Useruserdata = Useruserdata; - cmsg->Facilitydataarray = Facilitydataarray; -} - -static inline void capi_fill_CONNECT_REQ(_cmsg * cmsg, __u16 ApplId, __u16 Messagenumber, - __u32 adr, - __u16 CIPValue, - _cstruct CalledPartyNumber, - _cstruct CallingPartyNumber, - _cstruct CalledPartySubaddress, - _cstruct CallingPartySubaddress, - __u16 B1protocol, - __u16 B2protocol, - __u16 B3protocol, - _cstruct B1configuration, - _cstruct B2configuration, - _cstruct B3configuration, - _cstruct BC, - _cstruct LLC, - _cstruct HLC, - _cstruct BChannelinformation, - _cstruct Keypadfacility, - _cstruct Useruserdata, - _cstruct Facilitydataarray) -{ - - capi_cmsg_header(cmsg, ApplId, 0x02, 0x80, Messagenumber, adr); - cmsg->CIPValue = CIPValue; - cmsg->CalledPartyNumber = CalledPartyNumber; - cmsg->CallingPartyNumber = CallingPartyNumber; - cmsg->CalledPartySubaddress = CalledPartySubaddress; - cmsg->CallingPartySubaddress = CallingPartySubaddress; - cmsg->B1protocol = B1protocol; - cmsg->B2protocol = B2protocol; - cmsg->B3protocol = B3protocol; - cmsg->B1configuration = B1configuration; - cmsg->B2configuration = B2configuration; - cmsg->B3configuration = B3configuration; - cmsg->BC = BC; - cmsg->LLC = LLC; - cmsg->HLC = HLC; - cmsg->BChannelinformation = BChannelinformation; - cmsg->Keypadfacility = Keypadfacility; - cmsg->Useruserdata = Useruserdata; - cmsg->Facilitydataarray = Facilitydataarray; -} - -static inline void capi_fill_DATA_B3_REQ(_cmsg * cmsg, __u16 ApplId, __u16 Messagenumber, - __u32 adr, - __u32 Data, - __u16 DataLength, - __u16 DataHandle, - __u16 Flags) -{ - - capi_cmsg_header(cmsg, ApplId, 0x86, 0x80, Messagenumber, adr); - cmsg->Data = Data; - cmsg->DataLength = DataLength; - cmsg->DataHandle = DataHandle; - cmsg->Flags = Flags; -} - -static inline void capi_fill_DISCONNECT_REQ(_cmsg * cmsg, __u16 ApplId, __u16 Messagenumber, - __u32 adr, - _cstruct BChannelinformation, - _cstruct Keypadfacility, - _cstruct Useruserdata, - _cstruct Facilitydataarray) -{ - - capi_cmsg_header(cmsg, ApplId, 0x04, 0x80, Messagenumber, adr); - cmsg->BChannelinformation = BChannelinformation; - cmsg->Keypadfacility = Keypadfacility; - cmsg->Useruserdata = Useruserdata; - cmsg->Facilitydataarray = Facilitydataarray; -} - -static inline void capi_fill_DISCONNECT_B3_REQ(_cmsg * cmsg, __u16 ApplId, __u16 Messagenumber, - __u32 adr, - _cstruct NCPI) -{ - - capi_cmsg_header(cmsg, ApplId, 0x84, 0x80, Messagenumber, adr); - cmsg->NCPI = NCPI; -} - -static inline void capi_fill_MANUFACTURER_REQ(_cmsg * cmsg, __u16 ApplId, __u16 Messagenumber, - __u32 adr, - __u32 ManuID, - __u32 Class, - __u32 Function, - _cstruct ManuData) -{ - - capi_cmsg_header(cmsg, ApplId, 0xff, 0x80, Messagenumber, adr); - cmsg->ManuID = ManuID; - cmsg->Class = Class; - cmsg->Function = Function; - cmsg->ManuData = ManuData; -} - -static inline void capi_fill_RESET_B3_REQ(_cmsg * cmsg, __u16 ApplId, __u16 Messagenumber, - __u32 adr, - _cstruct NCPI) -{ - - capi_cmsg_header(cmsg, ApplId, 0x87, 0x80, Messagenumber, adr); - cmsg->NCPI = NCPI; -} - -static inline void capi_fill_SELECT_B_PROTOCOL_REQ(_cmsg * cmsg, __u16 ApplId, __u16 Messagenumber, - __u32 adr, - __u16 B1protocol, - __u16 B2protocol, - __u16 B3protocol, - _cstruct B1configuration, - _cstruct B2configuration, - _cstruct B3configuration) -{ - - capi_cmsg_header(cmsg, ApplId, 0x41, 0x80, Messagenumber, adr); - cmsg->B1protocol = B1protocol; - cmsg->B2protocol = B2protocol; - cmsg->B3protocol = B3protocol; - cmsg->B1configuration = B1configuration; - cmsg->B2configuration = B2configuration; - cmsg->B3configuration = B3configuration; -} - -static inline void capi_fill_CONNECT_RESP(_cmsg * cmsg, __u16 ApplId, __u16 Messagenumber, - __u32 adr, - __u16 Reject, - __u16 B1protocol, - __u16 B2protocol, - __u16 B3protocol, - _cstruct B1configuration, - _cstruct B2configuration, - _cstruct B3configuration, - _cstruct ConnectedNumber, - _cstruct ConnectedSubaddress, - _cstruct LLC, - _cstruct BChannelinformation, - _cstruct Keypadfacility, - _cstruct Useruserdata, - _cstruct Facilitydataarray) -{ - capi_cmsg_header(cmsg, ApplId, 0x02, 0x83, Messagenumber, adr); - cmsg->Reject = Reject; - cmsg->B1protocol = B1protocol; - cmsg->B2protocol = B2protocol; - cmsg->B3protocol = B3protocol; - cmsg->B1configuration = B1configuration; - cmsg->B2configuration = B2configuration; - cmsg->B3configuration = B3configuration; - cmsg->ConnectedNumber = ConnectedNumber; - cmsg->ConnectedSubaddress = ConnectedSubaddress; - cmsg->LLC = LLC; - cmsg->BChannelinformation = BChannelinformation; - cmsg->Keypadfacility = Keypadfacility; - cmsg->Useruserdata = Useruserdata; - cmsg->Facilitydataarray = Facilitydataarray; -} - -static inline void capi_fill_CONNECT_ACTIVE_RESP(_cmsg * cmsg, __u16 ApplId, __u16 Messagenumber, - __u32 adr) -{ - - capi_cmsg_header(cmsg, ApplId, 0x03, 0x83, Messagenumber, adr); -} - -static inline void capi_fill_CONNECT_B3_ACTIVE_RESP(_cmsg * cmsg, __u16 ApplId, __u16 Messagenumber, - __u32 adr) -{ - - capi_cmsg_header(cmsg, ApplId, 0x83, 0x83, Messagenumber, adr); -} - -static inline void capi_fill_CONNECT_B3_RESP(_cmsg * cmsg, __u16 ApplId, __u16 Messagenumber, - __u32 adr, - __u16 Reject, - _cstruct NCPI) -{ - capi_cmsg_header(cmsg, ApplId, 0x82, 0x83, Messagenumber, adr); - cmsg->Reject = Reject; - cmsg->NCPI = NCPI; -} - -static inline void capi_fill_CONNECT_B3_T90_ACTIVE_RESP(_cmsg * cmsg, __u16 ApplId, __u16 Messagenumber, - __u32 adr) -{ - - capi_cmsg_header(cmsg, ApplId, 0x88, 0x83, Messagenumber, adr); -} - -static inline void capi_fill_DATA_B3_RESP(_cmsg * cmsg, __u16 ApplId, __u16 Messagenumber, - __u32 adr, - __u16 DataHandle) -{ - - capi_cmsg_header(cmsg, ApplId, 0x86, 0x83, Messagenumber, adr); - cmsg->DataHandle = DataHandle; -} - -static inline void capi_fill_DISCONNECT_B3_RESP(_cmsg * cmsg, __u16 ApplId, __u16 Messagenumber, - __u32 adr) -{ - - capi_cmsg_header(cmsg, ApplId, 0x84, 0x83, Messagenumber, adr); -} - -static inline void capi_fill_DISCONNECT_RESP(_cmsg * cmsg, __u16 ApplId, __u16 Messagenumber, - __u32 adr) -{ - - capi_cmsg_header(cmsg, ApplId, 0x04, 0x83, Messagenumber, adr); -} - -static inline void capi_fill_FACILITY_RESP(_cmsg * cmsg, __u16 ApplId, __u16 Messagenumber, - __u32 adr, - __u16 FacilitySelector) -{ - - capi_cmsg_header(cmsg, ApplId, 0x80, 0x83, Messagenumber, adr); - cmsg->FacilitySelector = FacilitySelector; -} - -static inline void capi_fill_INFO_RESP(_cmsg * cmsg, __u16 ApplId, __u16 Messagenumber, - __u32 adr) -{ - - capi_cmsg_header(cmsg, ApplId, 0x08, 0x83, Messagenumber, adr); -} - -static inline void capi_fill_MANUFACTURER_RESP(_cmsg * cmsg, __u16 ApplId, __u16 Messagenumber, - __u32 adr, - __u32 ManuID, - __u32 Class, - __u32 Function, - _cstruct ManuData) -{ - - capi_cmsg_header(cmsg, ApplId, 0xff, 0x83, Messagenumber, adr); - cmsg->ManuID = ManuID; - cmsg->Class = Class; - cmsg->Function = Function; - cmsg->ManuData = ManuData; -} - -static inline void capi_fill_RESET_B3_RESP(_cmsg * cmsg, __u16 ApplId, __u16 Messagenumber, - __u32 adr) -{ - - capi_cmsg_header(cmsg, ApplId, 0x87, 0x83, Messagenumber, adr); -} - #endif /* __CAPIUTIL_H__ */ diff --git a/include/linux/kernelcapi.h b/include/linux/kernelcapi.h index 075fab5f92e1..94ba42bf9da1 100644 --- a/include/linux/kernelcapi.h +++ b/include/linux/kernelcapi.h @@ -10,46 +10,12 @@ #ifndef __KERNELCAPI_H__ #define __KERNELCAPI_H__ - #include <linux/list.h> #include <linux/skbuff.h> #include <linux/workqueue.h> #include <linux/notifier.h> #include <uapi/linux/kernelcapi.h> -struct capi20_appl { - u16 applid; - capi_register_params rparam; - void (*recv_message)(struct capi20_appl *ap, struct sk_buff *skb); - void *private; - - /* internal to kernelcapi.o */ - unsigned long nrecvctlpkt; - unsigned long nrecvdatapkt; - unsigned long nsentctlpkt; - unsigned long nsentdatapkt; - struct mutex recv_mtx; - struct sk_buff_head recv_queue; - struct work_struct recv_work; - int release_in_progress; -}; - -u16 capi20_isinstalled(void); -u16 capi20_register(struct capi20_appl *ap); -u16 capi20_release(struct capi20_appl *ap); -u16 capi20_put_message(struct capi20_appl *ap, struct sk_buff *skb); -u16 capi20_get_manufacturer(u32 contr, u8 buf[CAPI_MANUFACTURER_LEN]); -u16 capi20_get_version(u32 contr, struct capi_version *verp); -u16 capi20_get_serial(u32 contr, u8 serial[CAPI_SERIAL_LEN]); -u16 capi20_get_profile(u32 contr, struct capi_profile *profp); -int capi20_manufacturer(unsigned long cmd, void __user *data); - -#define CAPICTR_UP 0 -#define CAPICTR_DOWN 1 - -int register_capictr_notifier(struct notifier_block *nb); -int unregister_capictr_notifier(struct notifier_block *nb); - #define CAPI_NOERROR 0x0000 #define CAPI_TOOMANYAPPLS 0x1001 @@ -76,45 +42,4 @@ int unregister_capictr_notifier(struct notifier_block *nb); #define CAPI_MSGCTRLERNOTSUPPORTEXTEQUIP 0x110a #define CAPI_MSGCTRLERONLYSUPPORTEXTEQUIP 0x110b -typedef enum { - CapiMessageNotSupportedInCurrentState = 0x2001, - CapiIllContrPlciNcci = 0x2002, - CapiNoPlciAvailable = 0x2003, - CapiNoNcciAvailable = 0x2004, - CapiNoListenResourcesAvailable = 0x2005, - CapiNoFaxResourcesAvailable = 0x2006, - CapiIllMessageParmCoding = 0x2007, -} RESOURCE_CODING_PROBLEM; - -typedef enum { - CapiB1ProtocolNotSupported = 0x3001, - CapiB2ProtocolNotSupported = 0x3002, - CapiB3ProtocolNotSupported = 0x3003, - CapiB1ProtocolParameterNotSupported = 0x3004, - CapiB2ProtocolParameterNotSupported = 0x3005, - CapiB3ProtocolParameterNotSupported = 0x3006, - CapiBProtocolCombinationNotSupported = 0x3007, - CapiNcpiNotSupported = 0x3008, - CapiCipValueUnknown = 0x3009, - CapiFlagsNotSupported = 0x300a, - CapiFacilityNotSupported = 0x300b, - CapiDataLengthNotSupportedByCurrentProtocol = 0x300c, - CapiResetProcedureNotSupportedByCurrentProtocol = 0x300d, - CapiTeiAssignmentFailed = 0x300e, -} REQUESTED_SERVICES_PROBLEM; - -typedef enum { - CapiSuccess = 0x0000, - CapiSupplementaryServiceNotSupported = 0x300e, - CapiRequestNotAllowedInThisState = 0x3010, -} SUPPLEMENTARY_SERVICE_INFO; - -typedef enum { - CapiProtocolErrorLayer1 = 0x3301, - CapiProtocolErrorLayer2 = 0x3302, - CapiProtocolErrorLayer3 = 0x3303, - CapiTimeOut = 0x3303, // SuppServiceReason - CapiCallGivenToOtherApplication = 0x3304, -} CAPI_REASON; - #endif /* __KERNELCAPI_H__ */ diff --git a/include/linux/platform_data/ad7266.h b/include/linux/platform_data/ad7266.h index 7de6c16122df..f0652567afba 100644 --- a/include/linux/platform_data/ad7266.h +++ b/include/linux/platform_data/ad7266.h @@ -40,14 +40,11 @@ enum ad7266_mode { * @range: Reference voltage range the device is configured for * @mode: Sample mode the device is configured for * @fixed_addr: Whether the address pins are hard-wired - * @addr_gpios: GPIOs used for controlling the address pins, only used if - * fixed_addr is set to false. */ struct ad7266_platform_data { enum ad7266_range range; enum ad7266_mode mode; bool fixed_addr; - unsigned int addr_gpios[3]; }; #endif diff --git a/include/linux/platform_data/ads1015.h b/include/linux/platform_data/ads1015.h deleted file mode 100644 index 4cc9ffcafcbf..000000000000 --- a/include/linux/platform_data/ads1015.h +++ /dev/null @@ -1,23 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0-or-later */ -/* - * Platform Data for ADS1015 12-bit 4-input ADC - * (C) Copyright 2010 - * Dirk Eibach, Guntermann & Drunck GmbH <eibach@gdsys.de> - */ - -#ifndef LINUX_ADS1015_H -#define LINUX_ADS1015_H - -#define ADS1015_CHANNELS 8 - -struct ads1015_channel_data { - bool enabled; - unsigned int pga; - unsigned int data_rate; -}; - -struct ads1015_platform_data { - struct ads1015_channel_data channel_data[ADS1015_CHANNELS]; -}; - -#endif /* LINUX_ADS1015_H */ diff --git a/include/uapi/linux/b1lli.h b/include/uapi/linux/b1lli.h deleted file mode 100644 index 4ae6ac9950df..000000000000 --- a/include/uapi/linux/b1lli.h +++ /dev/null @@ -1,74 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */ -/* $Id: b1lli.h,v 1.8.8.3 2001/09/23 22:25:05 kai Exp $ - * - * ISDN lowlevel-module for AVM B1-card. - * - * Copyright 1996 by Carsten Paeth (calle@calle.in-berlin.de) - * - * This software may be used and distributed according to the terms - * of the GNU General Public License, incorporated herein by reference. - * - */ - -#ifndef _B1LLI_H_ -#define _B1LLI_H_ -/* - * struct for loading t4 file - */ -typedef struct avmb1_t4file { - int len; - unsigned char *data; -} avmb1_t4file; - -typedef struct avmb1_loaddef { - int contr; - avmb1_t4file t4file; -} avmb1_loaddef; - -typedef struct avmb1_loadandconfigdef { - int contr; - avmb1_t4file t4file; - avmb1_t4file t4config; -} avmb1_loadandconfigdef; - -typedef struct avmb1_resetdef { - int contr; -} avmb1_resetdef; - -typedef struct avmb1_getdef { - int contr; - int cardtype; - int cardstate; -} avmb1_getdef; - -/* - * struct for adding new cards - */ -typedef struct avmb1_carddef { - int port; - int irq; -} avmb1_carddef; - -#define AVM_CARDTYPE_B1 0 -#define AVM_CARDTYPE_T1 1 -#define AVM_CARDTYPE_M1 2 -#define AVM_CARDTYPE_M2 3 - -typedef struct avmb1_extcarddef { - int port; - int irq; - int cardtype; - int cardnr; /* for HEMA/T1 */ -} avmb1_extcarddef; - -#define AVMB1_LOAD 0 /* load image to card */ -#define AVMB1_ADDCARD 1 /* add a new card - OBSOLETE */ -#define AVMB1_RESETCARD 2 /* reset a card */ -#define AVMB1_LOAD_AND_CONFIG 3 /* load image and config to card */ -#define AVMB1_ADDCARD_WITH_TYPE 4 /* add a new card, with cardtype */ -#define AVMB1_GET_CARDINFO 5 /* get cardtype */ -#define AVMB1_REMOVECARD 6 /* remove a card - OBSOLETE */ - -#define AVMB1_REGISTERCARD_IS_OBSOLETE - -#endif /* _B1LLI_H_ */ diff --git a/include/uapi/linux/gigaset_dev.h b/include/uapi/linux/gigaset_dev.h deleted file mode 100644 index 279551af8ebf..000000000000 --- a/include/uapi/linux/gigaset_dev.h +++ /dev/null @@ -1,39 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ WITH Linux-syscall-note */ -/* - * interface to user space for the gigaset driver - * - * Copyright (c) 2004 by Hansjoerg Lipp <hjlipp@web.de> - * - * ===================================================================== - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * ===================================================================== - */ - -#ifndef GIGASET_INTERFACE_H -#define GIGASET_INTERFACE_H - -#include <linux/ioctl.h> - -/* The magic IOCTL value for this interface. */ -#define GIGASET_IOCTL 0x47 - -/* enable/disable device control via character device (lock out ISDN subsys) */ -#define GIGASET_REDIR _IOWR(GIGASET_IOCTL, 0, int) - -/* enable adapter configuration mode (M10x only) */ -#define GIGASET_CONFIG _IOWR(GIGASET_IOCTL, 1, int) - -/* set break characters (M105 only) */ -#define GIGASET_BRKCHARS _IOW(GIGASET_IOCTL, 2, unsigned char[6]) - -/* get version information selected by arg[0] */ -#define GIGASET_VERSION _IOWR(GIGASET_IOCTL, 3, unsigned[4]) -/* values for GIGASET_VERSION arg[0] */ -#define GIGVER_DRIVER 0 /* get driver version */ -#define GIGVER_COMPAT 1 /* get interface compatibility version */ -#define GIGVER_FWBASE 2 /* get base station firmware version */ - -#endif diff --git a/include/uapi/linux/hysdn_if.h b/include/uapi/linux/hysdn_if.h deleted file mode 100644 index 99f77c517e6d..000000000000 --- a/include/uapi/linux/hysdn_if.h +++ /dev/null @@ -1,34 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */ -/* $Id: hysdn_if.h,v 1.1.8.3 2001/09/23 22:25:05 kai Exp $ - * - * Linux driver for HYSDN cards - * ioctl definitions shared by hynetmgr and driver. - * - * Author Werner Cornelius (werner@titro.de) for Hypercope GmbH - * Copyright 1999 by Werner Cornelius (werner@titro.de) - * - * This software may be used and distributed according to the terms - * of the GNU General Public License, incorporated herein by reference. - * - */ - -/****************/ -/* error values */ -/****************/ -#define ERR_NONE 0 /* no error occurred */ -#define ERR_ALREADY_BOOT 1000 /* we are already booting */ -#define EPOF_BAD_MAGIC 1001 /* bad magic in POF header */ -#define ERR_BOARD_DPRAM 1002 /* board DPRAM failed */ -#define EPOF_INTERNAL 1003 /* internal POF handler error */ -#define EPOF_BAD_IMG_SIZE 1004 /* POF boot image size invalid */ -#define ERR_BOOTIMG_FAIL 1005 /* 1. stage boot image did not start */ -#define ERR_BOOTSEQ_FAIL 1006 /* 2. stage boot seq handshake timeout */ -#define ERR_POF_TIMEOUT 1007 /* timeout waiting for card pof ready */ -#define ERR_NOT_BOOTED 1008 /* operation only allowed when booted */ -#define ERR_CONF_LONG 1009 /* conf line is too long */ -#define ERR_INV_CHAN 1010 /* invalid channel number */ -#define ERR_ASYNC_TIME 1011 /* timeout sending async data */ - - - - |