diff options
303 files changed, 2996 insertions, 2057 deletions
diff --git a/Documentation/devicetree/bindings/arm/calxeda.txt b/Documentation/devicetree/bindings/arm/calxeda.txt new file mode 100644 index 000000000000..4755caaccba6 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/calxeda.txt @@ -0,0 +1,8 @@ +Calxeda Highbank Platforms Device Tree Bindings +----------------------------------------------- + +Boards with Calxeda Cortex-A9 based Highbank SOC shall have the following +properties. + +Required root node properties: + - compatible = "calxeda,highbank"; diff --git a/Documentation/devicetree/bindings/arm/l2cc.txt b/Documentation/devicetree/bindings/arm/l2cc.txt new file mode 100644 index 000000000000..7ca52161e7ab --- /dev/null +++ b/Documentation/devicetree/bindings/arm/l2cc.txt @@ -0,0 +1,44 @@ +* ARM L2 Cache Controller + +ARM cores often have a separate level 2 cache controller. There are various +implementations of the L2 cache controller with compatible programming models. +The ARM L2 cache representation in the device tree should be done as follows: + +Required properties: + +- compatible : should be one of: + "arm,pl310-cache" + "arm,l220-cache" + "arm,l210-cache" +- cache-unified : Specifies the cache is a unified cache. +- cache-level : Should be set to 2 for a level 2 cache. +- reg : Physical base address and size of cache controller's memory mapped + registers. + +Optional properties: + +- arm,data-latency : Cycles of latency for Data RAM accesses. Specifies 3 cells of + read, write and setup latencies. Minimum valid values are 1. Controllers + without setup latency control should use a value of 0. +- arm,tag-latency : Cycles of latency for Tag RAM accesses. Specifies 3 cells of + read, write and setup latencies. Controllers without setup latency control + should use 0. Controllers without separate read and write Tag RAM latency + values should only use the first cell. +- arm,dirty-latency : Cycles of latency for Dirty RAMs. This is a single cell. +- arm,filter-ranges : <start length> Starting address and length of window to + filter. Addresses in the filter window are directed to the M1 port. Other + addresses will go to the M0 port. +- interrupts : 1 combined interrupt. + +Example: + +L2: cache-controller { + compatible = "arm,pl310-cache"; + reg = <0xfff12000 0x1000>; + arm,data-latency = <1 1 1>; + arm,tag-latency = <2 2 2>; + arm,filter-latency = <0x80000000 0x8000000>; + cache-unified; + cache-level = <2>; + interrupts = <45>; +}; diff --git a/MAINTAINERS b/MAINTAINERS index 6185d0513584..5066335b97de 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -688,6 +688,12 @@ F: drivers/mtd/nand/bcm_umi_nand.c F: drivers/mtd/nand/bcm_umi_bch.c F: drivers/mtd/nand/nand_bcm_umi.h +ARM/CALXEDA HIGHBANK ARCHITECTURE +M: Rob Herring <rob.herring@calxeda.com> +L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers) +S: Maintained +F: arch/arm/mach-highbank/ + ARM/CAVIUM NETWORKS CNS3XXX MACHINE SUPPORT M: Anton Vorontsov <avorontsov@mvista.com> S: Maintained diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index a94a09ba356b..6147d30a832c 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -330,6 +330,20 @@ config ARCH_BCMRING help Support for Broadcom's BCMRing platform. +config ARCH_HIGHBANK + bool "Calxeda Highbank-based" + select ARCH_WANT_OPTIONAL_GPIOLIB + select ARM_AMBA + select ARM_GIC + select ARM_TIMER_SP804 + select CLKDEV_LOOKUP + select CPU_V7 + select GENERIC_CLOCKEVENTS + select HAVE_ARM_SCU + select USE_OF + help + Support for the Calxeda Highbank SoC based boards. + config ARCH_CLPS711X bool "Cirrus Logic CLPS711x/EP721x-based" select CPU_ARM720T @@ -862,6 +876,7 @@ config ARCH_U300 select CLKDEV_LOOKUP select HAVE_MACH_CLKDEV select GENERIC_GPIO + select ARCH_REQUIRE_GPIOLIB select NEED_MACH_MEMORY_H help Support for ST-Ericsson U300 series mobile platforms. @@ -1402,7 +1417,7 @@ config SMP depends on REALVIEW_EB_ARM11MP || REALVIEW_EB_A9MP || \ MACH_REALVIEW_PB11MP || MACH_REALVIEW_PBX || ARCH_OMAP4 || \ ARCH_EXYNOS4 || ARCH_TEGRA || ARCH_U8500 || ARCH_VEXPRESS_CA9X4 || \ - ARCH_MSM_SCORPIONMP || ARCH_SHMOBILE + ARCH_MSM_SCORPIONMP || ARCH_SHMOBILE || ARCH_HIGHBANK select USE_GENERIC_SMP_HELPERS select HAVE_ARM_SCU if !ARCH_MSM_SCORPIONMP help diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug index be3a0f78d915..4bb7eb90f070 100644 --- a/arch/arm/Kconfig.debug +++ b/arch/arm/Kconfig.debug @@ -65,13 +65,78 @@ config DEBUG_USER # These options are only for real kernel hackers who want to get their hands dirty. config DEBUG_LL - bool "Kernel low-level debugging functions" + bool "Kernel low-level debugging functions (read help!)" depends on DEBUG_KERNEL help Say Y here to include definitions of printascii, printch, printhex in the kernel. This is helpful if you are debugging code that executes before the console is initialized. + Note that selecting this option will limit the kernel to a single + UART definition, as specified below. Attempting to boot the kernel + image on a different platform *will not work*, so this option should + not be enabled for kernels that are intended to be portable. + +choice + prompt "Kernel low-level debugging port" + depends on DEBUG_LL + + config DEBUG_LL_UART_NONE + bool "No low-level debugging UART" + help + Say Y here if your platform doesn't provide a UART option + below. This relies on your platform choosing the right UART + definition internally in order for low-level debugging to + work. + + config DEBUG_ICEDCC + bool "Kernel low-level debugging via EmbeddedICE DCC channel" + help + Say Y here if you want the debug print routines to direct + their output to the EmbeddedICE macrocell's DCC channel using + co-processor 14. This is known to work on the ARM9 style ICE + channel and on the XScale with the PEEDI. + + Note that the system will appear to hang during boot if there + is nothing connected to read from the DCC. + + config DEBUG_FOOTBRIDGE_COM1 + bool "Kernel low-level debugging messages via footbridge 8250 at PCI COM1" + depends on FOOTBRIDGE + help + Say Y here if you want the debug print routines to direct + their output to the 8250 at PCI COM1. + + config DEBUG_DC21285_PORT + bool "Kernel low-level debugging messages via footbridge serial port" + depends on FOOTBRIDGE + help + Say Y here if you want the debug print routines to direct + their output to the serial port in the DC21285 (Footbridge). + + config DEBUG_CLPS711X_UART1 + bool "Kernel low-level debugging messages via UART1" + depends on ARCH_CLPS711X + help + Say Y here if you want the debug print routines to direct + their output to the first serial port on these devices. + + config DEBUG_CLPS711X_UART2 + bool "Kernel low-level debugging messages via UART2" + depends on ARCH_CLPS711X + help + Say Y here if you want the debug print routines to direct + their output to the second serial port on these devices. + + config DEBUG_HIGHBANK_UART + bool "Kernel low-level debugging messages via Highbank UART" + depends on ARCH_HIGHBANK + help + Say Y here if you want the debug print routines to direct + their output to the UART on Highbank based devices. + +endchoice + config EARLY_PRINTK bool "Early printk" depends on DEBUG_LL @@ -80,18 +145,6 @@ config EARLY_PRINTK kernel low-level debugging functions. Add earlyprintk to your kernel parameters to enable this console. -config DEBUG_ICEDCC - bool "Kernel low-level debugging via EmbeddedICE DCC channel" - depends on DEBUG_LL - help - Say Y here if you want the debug print routines to direct their - output to the EmbeddedICE macrocell's DCC channel using - co-processor 14. This is known to work on the ARM9 style ICE - channel and on the XScale with the PEEDI. - - It does include a timeout to ensure that the system does not - totally freeze when there is nothing connected to read. - config OC_ETM bool "On-chip ETM and ETB" select ARM_AMBA @@ -100,23 +153,6 @@ config OC_ETM buffer driver that will allow you to collect traces of the kernel code. -config DEBUG_DC21285_PORT - bool "Kernel low-level debugging messages via footbridge serial port" - depends on DEBUG_LL && FOOTBRIDGE - help - Say Y here if you want the debug print routines to direct their - output to the serial port in the DC21285 (Footbridge). Saying N - will cause the debug messages to appear on the first 16550 - serial port. - -config DEBUG_CLPS711X_UART2 - bool "Kernel low-level debugging messages via UART2" - depends on DEBUG_LL && ARCH_CLPS711X - help - Say Y here if you want the debug print routines to direct their - output to the second serial port on these devices. Saying N will - cause the debug messages to appear on the first serial port. - config DEBUG_S3C_UART depends on PLAT_SAMSUNG int "S3C UART to use for low-level debug" diff --git a/arch/arm/Makefile b/arch/arm/Makefile index 8904caa736cb..e8688114ca95 100644 --- a/arch/arm/Makefile +++ b/arch/arm/Makefile @@ -144,6 +144,7 @@ machine-$(CONFIG_ARCH_EBSA110) := ebsa110 machine-$(CONFIG_ARCH_EP93XX) := ep93xx machine-$(CONFIG_ARCH_GEMINI) := gemini machine-$(CONFIG_ARCH_H720X) := h720x +machine-$(CONFIG_ARCH_HIGHBANK) := highbank machine-$(CONFIG_ARCH_INTEGRATOR) := integrator machine-$(CONFIG_ARCH_IOP13XX) := iop13xx machine-$(CONFIG_ARCH_IOP32X) := iop32x diff --git a/arch/arm/boot/dts/highbank.dts b/arch/arm/boot/dts/highbank.dts new file mode 100644 index 000000000000..aeb1a7578fad --- /dev/null +++ b/arch/arm/boot/dts/highbank.dts @@ -0,0 +1,198 @@ +/* + * Copyright 2011 Calxeda, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ + +/dts-v1/; + +/* First 4KB has pen for secondary cores. */ +/memreserve/ 0x00000000 0x0001000; + +/ { + model = "Calxeda Highbank"; + compatible = "calxeda,highbank"; + #address-cells = <1>; + #size-cells = <1>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + compatible = "arm,cortex-a9"; + reg = <0>; + next-level-cache = <&L2>; + }; + + cpu@1 { + compatible = "arm,cortex-a9"; + reg = <1>; + next-level-cache = <&L2>; + }; + + cpu@2 { + compatible = "arm,cortex-a9"; + reg = <2>; + next-level-cache = <&L2>; + }; + + cpu@3 { + compatible = "arm,cortex-a9"; + reg = <3>; + next-level-cache = <&L2>; + }; + }; + + memory { + name = "memory"; + device_type = "memory"; + reg = <0x00000000 0xff900000>; + }; + + chosen { + bootargs = "console=ttyAMA0"; + }; + + soc { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + interrupt-parent = <&intc>; + ranges; + + timer@fff10600 { + compatible = "arm,smp-twd"; + reg = <0xfff10600 0x20>; + interrupts = <1 13 0xf04>; + }; + + watchdog@fff10620 { + compatible = "arm,cortex-a9-wdt"; + reg = <0xfff10620 0x20>; + interrupts = <1 14 0xf04>; + }; + + intc: interrupt-controller@fff11000 { + compatible = "arm,cortex-a9-gic"; + #interrupt-cells = <3>; + #size-cells = <0>; + #address-cells = <1>; + interrupt-controller; + interrupt-parent; + reg = <0xfff11000 0x1000>, + <0xfff10100 0x100>; + }; + + L2: l2-cache { + compatible = "arm,pl310-cache"; + reg = <0xfff12000 0x1000>; + interrupts = <0 70 4>; + cache-unified; + cache-level = <2>; + }; + + pmu { + compatible = "arm,cortex-a9-pmu"; + interrupts = <0 76 4 0 75 4 0 74 4 0 73 4>; + }; + + sata@ffe08000 { + compatible = "calxeda,hb-ahci"; + reg = <0xffe08000 0x10000>; + interrupts = <0 83 4>; + }; + + sdhci@ffe0e000 { + compatible = "calxeda,hb-sdhci"; + reg = <0xffe0e000 0x1000>; + interrupts = <0 90 4>; + }; + + ipc@fff20000 { + compatible = "arm,pl320", "arm,primecell"; + reg = <0xfff20000 0x1000>; + interrupts = <0 7 4>; + }; + + gpioe: gpio@fff30000 { + #gpio-cells = <2>; + compatible = "arm,pl061", "arm,primecell"; + gpio-controller; + reg = <0xfff30000 0x1000>; + interrupts = <0 14 4>; + }; + + gpiof: gpio@fff31000 { + #gpio-cells = <2>; + compatible = "arm,pl061", "arm,primecell"; + gpio-controller; + reg = <0xfff31000 0x1000>; + interrupts = <0 15 4>; + }; + + gpiog: gpio@fff32000 { + #gpio-cells = <2>; + compatible = "arm,pl061", "arm,primecell"; + gpio-controller; + reg = <0xfff32000 0x1000>; + interrupts = <0 16 4>; + }; + + gpioh: gpio@fff33000 { + #gpio-cells = <2>; + compatible = "arm,pl061", "arm,primecell"; + gpio-controller; + reg = <0xfff33000 0x1000>; + interrupts = <0 17 4>; + }; + + timer { + compatible = "arm,sp804", "arm,primecell"; + reg = <0xfff34000 0x1000>; + interrupts = <0 18 4>; + }; + + rtc@fff35000 { + compatible = "arm,pl031", "arm,primecell"; + reg = <0xfff35000 0x1000>; + interrupts = <0 19 4>; + }; + + serial@fff36000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0xfff36000 0x1000>; + interrupts = <0 20 4>; + }; + + smic@fff3a000 { + compatible = "ipmi-smic"; + device_type = "ipmi"; + reg = <0xfff3a000 0x1000>; + interrupts = <0 24 4>; + reg-size = <4>; + reg-spacing = <4>; + }; + + sregs@fff3c000 { + compatible = "calxeda,hb-sregs"; + reg = <0xfff3c000 0x1000>; + }; + + dma@fff3d000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0xfff3d000 0x1000>; + interrupts = <0 92 4>; + }; + }; +}; diff --git a/arch/arm/common/scoop.c b/arch/arm/common/scoop.c index a07b0e763a80..1cde34a080d7 100644 --- a/arch/arm/common/scoop.c +++ b/arch/arm/common/scoop.c @@ -12,11 +12,11 @@ */ #include <linux/device.h> +#include <linux/gpio.h> #include <linux/string.h> #include <linux/slab.h> #include <linux/platform_device.h> #include <linux/io.h> -#include <asm/gpio.h> #include <asm/hardware/scoop.h> /* PCMCIA to Scoop linkage diff --git a/arch/arm/include/asm/ecard.h b/arch/arm/include/asm/ecard.h index 29f2610efc70..eaea14676d57 100644 --- a/arch/arm/include/asm/ecard.h +++ b/arch/arm/include/asm/ecard.h @@ -161,7 +161,6 @@ struct expansion_card { /* Private internal data */ const char *card_desc; /* Card description */ - CONST unsigned int podaddr; /* Base Linux address for card */ CONST loader_t loader; /* loader program */ u64 dma_mask; }; diff --git a/arch/arm/include/asm/gpio.h b/arch/arm/include/asm/gpio.h index 166a7a3e2840..11ad0bfbb0ad 100644 --- a/arch/arm/include/asm/gpio.h +++ b/arch/arm/include/asm/gpio.h @@ -4,4 +4,23 @@ /* not all ARM platforms necessarily support this API ... */ #include <mach/gpio.h> +#ifndef __ARM_GPIOLIB_COMPLEX +/* Note: this may rely upon the value of ARCH_NR_GPIOS set in mach/gpio.h */ +#include <asm-generic/gpio.h> + +/* The trivial gpiolib dispatchers */ +#define gpio_get_value __gpio_get_value +#define gpio_set_value __gpio_set_value +#define gpio_cansleep __gpio_cansleep +#endif + +/* + * Provide a default gpio_to_irq() which should satisfy every case. + * However, some platforms want to do this differently, so allow them + * to override it. + */ +#ifndef gpio_to_irq +#define gpio_to_irq __gpio_to_irq +#endif + #endif /* _ARCH_ARM_GPIO_H */ diff --git a/arch/arm/include/asm/hardware/cache-l2x0.h b/arch/arm/include/asm/hardware/cache-l2x0.h index 99a6ed7e1bfd..1db1143a9483 100644 --- a/arch/arm/include/asm/hardware/cache-l2x0.h +++ b/arch/arm/include/asm/hardware/cache-l2x0.h @@ -52,6 +52,8 @@ #define L2X0_LOCKDOWN_WAY_D_BASE 0x900 #define L2X0_LOCKDOWN_WAY_I_BASE 0x904 #define L2X0_LOCKDOWN_STRIDE 0x08 +#define L2X0_ADDR_FILTER_START 0xC00 +#define L2X0_ADDR_FILTER_END 0xC04 #define L2X0_TEST_OPERATION 0xF00 #define L2X0_LINE_DATA 0xF10 #define L2X0_LINE_TAG 0xF30 @@ -65,8 +67,23 @@ #define L2X0_CACHE_ID_PART_MASK (0xf << 6) #define L2X0_CACHE_ID_PART_L210 (1 << 6) #define L2X0_CACHE_ID_PART_L310 (3 << 6) +#define L2X0_CACHE_ID_RTL_MASK 0x3f +#define L2X0_CACHE_ID_RTL_R0P0 0x0 +#define L2X0_CACHE_ID_RTL_R1P0 0x2 +#define L2X0_CACHE_ID_RTL_R2P0 0x4 +#define L2X0_CACHE_ID_RTL_R3P0 0x5 +#define L2X0_CACHE_ID_RTL_R3P1 0x6 +#define L2X0_CACHE_ID_RTL_R3P2 0x8 #define L2X0_AUX_CTRL_MASK 0xc0000fff +#define L2X0_AUX_CTRL_DATA_RD_LATENCY_SHIFT 0 +#define L2X0_AUX_CTRL_DATA_RD_LATENCY_MASK 0x7 +#define L2X0_AUX_CTRL_DATA_WR_LATENCY_SHIFT 3 +#define L2X0_AUX_CTRL_DATA_WR_LATENCY_MASK (0x7 << 3) +#define L2X0_AUX_CTRL_TAG_LATENCY_SHIFT 6 +#define L2X0_AUX_CTRL_TAG_LATENCY_MASK (0x7 << 6) +#define L2X0_AUX_CTRL_DIRTY_LATENCY_SHIFT 9 +#define L2X0_AUX_CTRL_DIRTY_LATENCY_MASK (0x7 << 9) #define L2X0_AUX_CTRL_ASSOCIATIVITY_SHIFT 16 #define L2X0_AUX_CTRL_WAY_SIZE_SHIFT 17 #define L2X0_AUX_CTRL_WAY_SIZE_MASK (0x7 << 17) @@ -77,8 +94,40 @@ #define L2X0_AUX_CTRL_INSTR_PREFETCH_SHIFT 29 #define L2X0_AUX_CTRL_EARLY_BRESP_SHIFT 30 +#define L2X0_LATENCY_CTRL_SETUP_SHIFT 0 +#define L2X0_LATENCY_CTRL_RD_SHIFT 4 +#define L2X0_LATENCY_CTRL_WR_SHIFT 8 + +#define L2X0_ADDR_FILTER_EN 1 + #ifndef __ASSEMBLY__ extern void __init l2x0_init(void __iomem *base, __u32 aux_val, __u32 aux_mask); +#if defined(CONFIG_CACHE_L2X0) && defined(CONFIG_OF) +extern int l2x0_of_init(__u32 aux_val, __u32 aux_mask); +#else +static inline int l2x0_of_init(__u32 aux_val, __u32 aux_mask) +{ + return -ENODEV; +} #endif +struct l2x0_regs { + unsigned long phy_base; + unsigned long aux_ctrl; + /* + * Whether the following registers need to be saved/restored + * depends on platform + */ + unsigned long tag_latency; + unsigned long data_latency; + unsigned long filter_start; + unsigned long filter_end; + unsigned long prefetch_ctrl; + unsigned long pwr_ctrl; +}; + +extern struct l2x0_regs l2x0_saved_regs; + +#endif /* __ASSEMBLY__ */ + #endif diff --git a/arch/arm/include/asm/hardware/iop3xx-gpio.h b/arch/arm/include/asm/hardware/iop3xx-gpio.h index b69d972b1f7d..9eda7dc92ad8 100644 --- a/arch/arm/include/asm/hardware/iop3xx-gpio.h +++ b/arch/arm/include/asm/hardware/iop3xx-gpio.h @@ -28,6 +28,8 @@ #include <mach/hardware.h> #include <asm-generic/gpio.h> +#define __ARM_GPIOLIB_COMPLEX + #define IOP3XX_N_GPIOS 8 static inline int gpio_get_value(unsigned gpio) diff --git a/arch/arm/include/asm/io.h b/arch/arm/include/asm/io.h index d66605dea55a..ffb089d46a17 100644 --- a/arch/arm/include/asm/io.h +++ b/arch/arm/include/asm/io.h @@ -110,6 +110,27 @@ static inline void __iomem *__typesafe_io(unsigned long addr) #include <mach/io.h> /* + * This is the limit of PC card/PCI/ISA IO space, which is by default + * 64K if we have PC card, PCI or ISA support. Otherwise, default to + * zero to prevent ISA/PCI drivers claiming IO space (and potentially + * oopsing.) + * + * Only set this larger if you really need inb() et.al. to operate over + * a larger address space. Note that SOC_COMMON ioremaps each sockets + * IO space area, and so inb() et.al. must be defined to operate as per + * readb() et.al. on such platforms. + */ +#ifndef IO_SPACE_LIMIT +#if defined(CONFIG_PCMCIA_SOC_COMMON) || defined(CONFIG_PCMCIA_SOC_COMMON_MODULE) +#define IO_SPACE_LIMIT ((resource_size_t)0xffffffff) +#elif defined(CONFIG_PCI) || defined(CONFIG_ISA) || defined(CONFIG_PCCARD) +#define IO_SPACE_LIMIT ((resource_size_t)0xffff) +#else +#define IO_SPACE_LIMIT ((resource_size_t)0) +#endif +#endif + +/* * IO port access primitives * ------------------------- * diff --git a/arch/arm/include/asm/outercache.h b/arch/arm/include/asm/outercache.h index d8387437ec5a..53426c66352a 100644 --- a/arch/arm/include/asm/outercache.h +++ b/arch/arm/include/asm/outercache.h @@ -34,6 +34,7 @@ struct outer_cache_fns { void (*sync)(void); #endif void (*set_debug)(unsigned long); + void (*resume)(void); }; #ifdef CONFIG_OUTER_CACHE @@ -74,6 +75,12 @@ static inline void outer_disable(void) outer_cache.disable(); } +static inline void outer_resume(void) +{ + if (outer_cache.resume) + outer_cache.resume(); +} + #else static inline void outer_inv_range(phys_addr_t start, phys_addr_t end) diff --git a/arch/arm/kernel/asm-offsets.c b/arch/arm/kernel/asm-offsets.c index 16baba2e4369..1429d8989fb9 100644 --- a/arch/arm/kernel/asm-offsets.c +++ b/arch/arm/kernel/asm-offsets.c @@ -20,6 +20,7 @@ #include <asm/thread_info.h> #include <asm/memory.h> #include <asm/procinfo.h> +#include <asm/hardware/cache-l2x0.h> #include <linux/kbuild.h> /* @@ -92,6 +93,17 @@ int main(void) DEFINE(S_OLD_R0, offsetof(struct pt_regs, ARM_ORIG_r0)); DEFINE(S_FRAME_SIZE, sizeof(struct pt_regs)); BLANK(); +#ifdef CONFIG_CACHE_L2X0 + DEFINE(L2X0_R_PHY_BASE, offsetof(struct l2x0_regs, phy_base)); + DEFINE(L2X0_R_AUX_CTRL, offsetof(struct l2x0_regs, aux_ctrl)); + DEFINE(L2X0_R_TAG_LATENCY, offsetof(struct l2x0_regs, tag_latency)); + DEFINE(L2X0_R_DATA_LATENCY, offsetof(struct l2x0_regs, data_latency)); + DEFINE(L2X0_R_FILTER_START, offsetof(struct l2x0_regs, filter_start)); + DEFINE(L2X0_R_FILTER_END, offsetof(struct l2x0_regs, filter_end)); + DEFINE(L2X0_R_PREFETCH_CTRL, offsetof(struct l2x0_regs, prefetch_ctrl)); + DEFINE(L2X0_R_PWR_CTRL, offsetof(struct l2x0_regs, pwr_ctrl)); + BLANK(); +#endif #ifdef CONFIG_CPU_HAS_ASID DEFINE(MM_CONTEXT_ID, offsetof(struct mm_struct, context.id)); BLANK(); diff --git a/arch/arm/kernel/ecard.c b/arch/arm/kernel/ecard.c index d16500110ee9..4dd0edab6a65 100644 --- a/arch/arm/kernel/ecard.c +++ b/arch/arm/kernel/ecard.c @@ -237,7 +237,7 @@ static void ecard_init_pgtables(struct mm_struct *mm) memcpy(dst_pgd, src_pgd, sizeof(pgd_t) * (IO_SIZE / PGDIR_SIZE)); - src_pgd = pgd_offset(mm, EASI_BASE); + src_pgd = pgd_offset(mm, (unsigned long)EASI_BASE); dst_pgd = pgd_offset(mm, EASI_START); memcpy(dst_pgd, src_pgd, sizeof(pgd_t) * (EASI_SIZE / PGDIR_SIZE)); @@ -674,44 +674,37 @@ static int __init ecard_probeirqhw(void) #define ecard_probeirqhw() (0) #endif -#ifndef IO_EC_MEMC8_BASE -#define IO_EC_MEMC8_BASE 0 -#endif - -static unsigned int __ecard_address(ecard_t *ec, card_type_t type, card_speed_t speed) +static void __iomem *__ecard_address(ecard_t *ec, card_type_t type, card_speed_t speed) { - unsigned long address = 0; + void __iomem *address = NULL; int slot = ec->slot_no; if (ec->slot_no == 8) - return IO_EC_MEMC8_BASE; + return ECARD_MEMC8_BASE; ectcr &= ~(1 << slot); switch (type) { case ECARD_MEMC: if (slot < 4) - address = IO_EC_MEMC_BASE + (slot << 12); + address = ECARD_MEMC_BASE + (slot << 14); break; case ECARD_IOC: if (slot < 4) - address = IO_EC_IOC_BASE + (slot << 12); -#ifdef IO_EC_IOC4_BASE + address = ECARD_IOC_BASE + (slot << 14); else - address = IO_EC_IOC4_BASE + ((slot - 4) << 12); -#endif + address = ECARD_IOC4_BASE + ((slot - 4) << 14); if (address) - address += speed << 17; + address += speed << 19; break; -#ifdef IO_EC_EASI_BASE case ECARD_EASI: - address = IO_EC_EASI_BASE + (slot << 22); + address = ECARD_EASI_BASE + (slot << 24); if (speed == ECARD_FAST) ectcr |= 1 << slot; break; -#endif + default: break; } @@ -990,6 +983,7 @@ ecard_probe(int slot, card_type_t type) ecard_t **ecp; ecard_t *ec; struct ex_ecid cid; + void __iomem *addr; int i, rc; ec = ecard_alloc_card(type, slot); @@ -999,7 +993,7 @@ ecard_probe(int slot, card_type_t type) } rc = -ENODEV; - if ((ec->podaddr = __ecard_address(ec, type, ECARD_SYNC)) == 0) + if ((addr = __ecard_address(ec, type, ECARD_SYNC)) == NULL) goto nodev; cid.r_zero = 1; @@ -1019,7 +1013,7 @@ ecard_probe(int slot, card_type_t type) ec->cid.fiqmask = cid.r_fiqmask; ec->cid.fiqoff = ecard_gets24(cid.r_fiqoff); ec->fiqaddr = - ec->irqaddr = (void __iomem *)ioaddr(ec->podaddr); + ec->irqaddr = addr; if (ec->cid.is) { ec->irqmask = ec->cid.irqmask; @@ -1048,10 +1042,8 @@ ecard_probe(int slot, card_type_t type) set_irq_flags(ec->irq, IRQF_VALID); } -#ifdef IO_EC_MEMC8_BASE if (slot == 8) ec->irq = 11; -#endif #ifdef CONFIG_ARCH_RPC /* On RiscPC, only first two slots have DMA capability */ if (slot < 2) @@ -1097,9 +1089,7 @@ static int __init ecard_init(void) ecard_probe(slot, ECARD_IOC); } -#ifdef IO_EC_MEMC8_BASE ecard_probe(8, ECARD_IOC); -#endif irqhw = ecard_probeirqhw(); diff --git a/arch/arm/mach-at91/at91cap9_devices.c b/arch/arm/mach-at91/at91cap9_devices.c index dba0d8d8a4bd..f87f5040e78e 100644 --- a/arch/arm/mach-at91/at91cap9_devices.c +++ b/arch/arm/mach-at91/at91cap9_devices.c @@ -16,6 +16,7 @@ #include <asm/mach/irq.h> #include <linux/dma-mapping.h> +#include <linux/gpio.h> #include <linux/platform_device.h> #include <linux/i2c-gpio.h> @@ -23,7 +24,6 @@ #include <mach/board.h> #include <mach/cpu.h> -#include <mach/gpio.h> #include <mach/at91cap9.h> #include <mach/at91cap9_matrix.h> #include <mach/at91sam9_smc.h> diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c index 7227755ffec6..978be950035a 100644 --- a/arch/arm/mach-at91/at91rm9200_devices.c +++ b/arch/arm/mach-at91/at91rm9200_devices.c @@ -14,11 +14,11 @@ #include <asm/mach/map.h> #include <linux/dma-mapping.h> +#include <linux/gpio.h> #include <linux/platform_device.h> #include <linux/i2c-gpio.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/at91rm9200.h> #include <mach/at91rm9200_mc.h> diff --git a/arch/arm/mach-at91/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c index 39f81f47b4ba..a53b3de9daa2 100644 --- a/arch/arm/mach-at91/at91sam9260_devices.c +++ b/arch/arm/mach-at91/at91sam9260_devices.c @@ -13,11 +13,11 @@ #include <asm/mach/map.h> #include <linux/dma-mapping.h> +#include <linux/gpio.h> #include <linux/platform_device.h> #include <linux/i2c-gpio.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/cpu.h> #include <mach/at91sam9260.h> #include <mach/at91sam9260_matrix.h> diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c index 0f917928eeb7..4e647b653339 100644 --- a/arch/arm/mach-at91/at91sam9261_devices.c +++ b/arch/arm/mach-at91/at91sam9261_devices.c @@ -14,6 +14,7 @@ #include <asm/mach/map.h> #include <linux/dma-mapping.h> +#include <linux/gpio.h> #include <linux/platform_device.h> #include <linux/i2c-gpio.h> @@ -21,7 +22,6 @@ #include <video/atmel_lcdc.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/at91sam9261.h> #include <mach/at91sam9261_matrix.h> #include <mach/at91sam9_smc.h> diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c index a050f41fc860..dd7662bc395f 100644 --- a/arch/arm/mach-at91/at91sam9263_devices.c +++ b/arch/arm/mach-at91/at91sam9263_devices.c @@ -13,6 +13,7 @@ #include <asm/mach/map.h> #include <linux/dma-mapping.h> +#include <linux/gpio.h> #include <linux/platform_device.h> #include <linux/i2c-gpio.h> @@ -20,7 +21,6 @@ #include <video/atmel_lcdc.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/at91sam9263.h> #include <mach/at91sam9263_matrix.h> #include <mach/at91sam9_smc.h> diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c index 600bffb01edb..c3dfb1b3b1e3 100644 --- a/arch/arm/mach-at91/at91sam9g45_devices.c +++ b/arch/arm/mach-at91/at91sam9g45_devices.c @@ -13,6 +13,7 @@ #include <asm/mach/map.h> #include <linux/dma-mapping.h> +#include <linux/gpio.h> #include <linux/platform_device.h> #include <linux/i2c-gpio.h> #include <linux/atmel-mci.h> @@ -21,7 +22,6 @@ #include <video/atmel_lcdc.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/at91sam9g45.h> #include <mach/at91sam9g45_matrix.h> #include <mach/at91sam9_smc.h> diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c index aacb19dc9225..305a851b5bff 100644 --- a/arch/arm/mach-at91/at91sam9rl_devices.c +++ b/arch/arm/mach-at91/at91sam9rl_devices.c @@ -10,6 +10,7 @@ #include <asm/mach/map.h> #include <linux/dma-mapping.h> +#include <linux/gpio.h> #include <linux/platform_device.h> #include <linux/i2c-gpio.h> @@ -17,7 +18,6 @@ #include <video/atmel_lcdc.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/at91sam9rl.h> #include <mach/at91sam9rl_matrix.h> #include <mach/at91sam9_smc.h> diff --git a/arch/arm/mach-at91/board-1arm.c b/arch/arm/mach-at91/board-1arm.c index 5aa58851eb39..367d5cd5e362 100644 --- a/arch/arm/mach-at91/board-1arm.c +++ b/arch/arm/mach-at91/board-1arm.c @@ -19,6 +19,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -34,7 +35,6 @@ #include <asm/mach/irq.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/cpu.h> #include "generic.h" diff --git a/arch/arm/mach-at91/board-afeb-9260v1.c b/arch/arm/mach-at91/board-afeb-9260v1.c index b0c796d42e49..0487ea10c2d6 100644 --- a/arch/arm/mach-at91/board-afeb-9260v1.c +++ b/arch/arm/mach-at91/board-afeb-9260v1.c @@ -25,6 +25,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -43,7 +44,6 @@ #include <asm/mach/irq.h> #include <mach/board.h> -#include <mach/gpio.h> #include "generic.h" diff --git a/arch/arm/mach-at91/board-cam60.c b/arch/arm/mach-at91/board-cam60.c index d1abd5898e85..747b2eaa9737 100644 --- a/arch/arm/mach-at91/board-cam60.c +++ b/arch/arm/mach-at91/board-cam60.c @@ -21,6 +21,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -38,7 +39,6 @@ #include <asm/mach/irq.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/at91sam9_smc.h> #include "sam9_smc.h" diff --git a/arch/arm/mach-at91/board-cap9adk.c b/arch/arm/mach-at91/board-cap9adk.c index 679b0b743e92..062670351a6a 100644 --- a/arch/arm/mach-at91/board-cap9adk.c +++ b/arch/arm/mach-at91/board-cap9adk.c @@ -22,6 +22,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -41,7 +42,6 @@ #include <asm/mach/map.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/at91cap9_matrix.h> #include <mach/at91sam9_smc.h> #include <mach/system_rev.h> diff --git a/arch/arm/mach-at91/board-carmeva.c b/arch/arm/mach-at91/board-carmeva.c index c578c5d90728..774c87fcbd5b 100644 --- a/arch/arm/mach-at91/board-carmeva.c +++ b/arch/arm/mach-at91/board-carmeva.c @@ -20,6 +20,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -35,7 +36,6 @@ #include <mach/hardware.h> #include <mach/board.h> -#include <mach/gpio.h> #include "generic.h" diff --git a/arch/arm/mach-at91/board-cpu9krea.c b/arch/arm/mach-at91/board-cpu9krea.c index f4da8a16d5dc..fc885a4ce243 100644 --- a/arch/arm/mach-at91/board-cpu9krea.c +++ b/arch/arm/mach-at91/board-cpu9krea.c @@ -21,6 +21,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -40,7 +41,6 @@ #include <mach/hardware.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/at91sam9_smc.h> #include <mach/at91sam9260_matrix.h> diff --git a/arch/arm/mach-at91/board-cpuat91.c b/arch/arm/mach-at91/board-cpuat91.c index 2d919f5a4f57..d35e65b08ccd 100644 --- a/arch/arm/mach-at91/board-cpuat91.c +++ b/arch/arm/mach-at91/board-cpuat91.c @@ -19,6 +19,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -36,7 +37,6 @@ #include <asm/mach/irq.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/at91rm9200_mc.h> #include <mach/cpu.h> diff --git a/arch/arm/mach-at91/board-csb337.c b/arch/arm/mach-at91/board-csb337.c index 17654d5e94e6..c3936665e645 100644 --- a/arch/arm/mach-at91/board-csb337.c +++ b/arch/arm/mach-at91/board-csb337.c @@ -19,6 +19,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -38,7 +39,6 @@ #include <mach/hardware.h> #include <mach/board.h> -#include <mach/gpio.h> #include "generic.h" diff --git a/arch/arm/mach-at91/board-csb637.c b/arch/arm/mach-at91/board-csb637.c index 72b55674616c..586100e2acbb 100644 --- a/arch/arm/mach-at91/board-csb637.c +++ b/arch/arm/mach-at91/board-csb637.c @@ -20,6 +20,7 @@ #include <linux/types.h> #include <linux/init.h> +#include <linux/gpio.h> #include <linux/mm.h> #include <linux/module.h> #include <linux/platform_device.h> @@ -35,7 +36,6 @@ #include <mach/hardware.h> #include <mach/board.h> -#include <mach/gpio.h> #include "generic.h" diff --git a/arch/arm/mach-at91/board-eb9200.c b/arch/arm/mach-at91/board-eb9200.c index 01170a2766a8..45db7a3dbef0 100644 --- a/arch/arm/mach-at91/board-eb9200.c +++ b/arch/arm/mach-at91/board-eb9200.c @@ -20,6 +20,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -35,7 +36,6 @@ #include <asm/mach/irq.h> #include <mach/board.h> -#include <mach/gpio.h> #include "generic.h" diff --git a/arch/arm/mach-at91/board-ecbat91.c b/arch/arm/mach-at91/board-ecbat91.c index 7c0313c51f26..2f9c16d29212 100644 --- a/arch/arm/mach-at91/board-ecbat91.c +++ b/arch/arm/mach-at91/board-ecbat91.c @@ -20,6 +20,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -37,7 +38,6 @@ #include <asm/mach/irq.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/cpu.h> #include "generic.h" diff --git a/arch/arm/mach-at91/board-kafa.c b/arch/arm/mach-at91/board-kafa.c index 4a170890b3b1..3bae73e63633 100644 --- a/arch/arm/mach-at91/board-kafa.c +++ b/arch/arm/mach-at91/board-kafa.c @@ -19,6 +19,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -34,7 +35,6 @@ #include <asm/mach/irq.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/cpu.h> #include "generic.h" diff --git a/arch/arm/mach-at91/board-kb9202.c b/arch/arm/mach-at91/board-kb9202.c index 9dc8d496ead1..15a3f1a87ab0 100644 --- a/arch/arm/mach-at91/board-kb9202.c +++ b/arch/arm/mach-at91/board-kb9202.c @@ -20,6 +20,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -35,7 +36,6 @@ #include <asm/mach/irq.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/cpu.h> #include <mach/at91rm9200_mc.h> diff --git a/arch/arm/mach-at91/board-neocore926.c b/arch/arm/mach-at91/board-neocore926.c index 9bc6ab32e0ac..6094496f7edb 100644 --- a/arch/arm/mach-at91/board-neocore926.c +++ b/arch/arm/mach-at91/board-neocore926.c @@ -21,6 +21,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -44,7 +45,6 @@ #include <mach/hardware.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/at91sam9_smc.h> #include "sam9_smc.h" diff --git a/arch/arm/mach-at91/board-picotux200.c b/arch/arm/mach-at91/board-picotux200.c index b7b8390e8a00..0a8fe6a1b7c8 100644 --- a/arch/arm/mach-at91/board-picotux200.c +++ b/arch/arm/mach-at91/board-picotux200.c @@ -20,6 +20,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -37,7 +38,6 @@ #include <asm/mach/irq.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/at91rm9200_mc.h> #include "generic.h" diff --git a/arch/arm/mach-at91/board-qil-a9260.c b/arch/arm/mach-at91/board-qil-a9260.c index 81f911033681..938cc390bea3 100644 --- a/arch/arm/mach-at91/board-qil-a9260.c +++ b/arch/arm/mach-at91/board-qil-a9260.c @@ -21,6 +21,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -40,7 +41,6 @@ #include <mach/hardware.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/at91sam9_smc.h> #include <mach/at91_shdwc.h> diff --git a/arch/arm/mach-at91/board-rm9200dk.c b/arch/arm/mach-at91/board-rm9200dk.c index 6f08faadb474..b4ac30e38a9e 100644 --- a/arch/arm/mach-at91/board-rm9200dk.c +++ b/arch/arm/mach-at91/board-rm9200dk.c @@ -22,6 +22,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -39,7 +40,6 @@ #include <mach/hardware.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/at91rm9200_mc.h> #include "generic.h" diff --git a/arch/arm/mach-at91/board-rm9200ek.c b/arch/arm/mach-at91/board-rm9200ek.c index 85bcccd7b9e4..99fd7f8aee0e 100644 --- a/arch/arm/mach-at91/board-rm9200ek.c +++ b/arch/arm/mach-at91/board-rm9200ek.c @@ -22,6 +22,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -39,7 +40,6 @@ #include <mach/hardware.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/at91rm9200_mc.h> #include "generic.h" diff --git a/arch/arm/mach-at91/board-sam9-l9260.c b/arch/arm/mach-at91/board-sam9-l9260.c index 4d3a02f1289e..2a21e790250e 100644 --- a/arch/arm/mach-at91/board-sam9-l9260.c +++ b/arch/arm/mach-at91/board-sam9-l9260.c @@ -21,6 +21,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -37,7 +38,6 @@ #include <asm/mach/irq.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/at91sam9_smc.h> #include "sam9_smc.h" diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c index 8a50c3e67186..89c8b579bfda 100644 --- a/arch/arm/mach-at91/board-sam9260ek.c +++ b/arch/arm/mach-at91/board-sam9260ek.c @@ -20,6 +20,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -41,7 +42,6 @@ #include <mach/hardware.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/at91sam9_smc.h> #include <mach/at91_shdwc.h> #include <mach/system_rev.h> diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c index 5096a0ec50c1..3741f43cdae9 100644 --- a/arch/arm/mach-at91/board-sam9261ek.c +++ b/arch/arm/mach-at91/board-sam9261ek.c @@ -20,6 +20,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -45,7 +46,6 @@ #include <mach/hardware.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/at91sam9_smc.h> #include <mach/at91_shdwc.h> #include <mach/system_rev.h> diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c index ea8f185d3b9d..a580dd451a41 100644 --- a/arch/arm/mach-at91/board-sam9263ek.c +++ b/arch/arm/mach-at91/board-sam9263ek.c @@ -20,6 +20,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -44,7 +45,6 @@ #include <mach/hardware.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/at91sam9_smc.h> #include <mach/at91_shdwc.h> #include <mach/system_rev.h> diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c index 817f59d7251b..8d77c2ff96b2 100644 --- a/arch/arm/mach-at91/board-sam9g20ek.c +++ b/arch/arm/mach-at91/board-sam9g20ek.c @@ -18,6 +18,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -41,7 +42,6 @@ #include <asm/mach/irq.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/at91sam9_smc.h> #include <mach/system_rev.h> diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c index ad234ccbf57e..2d6203ac1a42 100644 --- a/arch/arm/mach-at91/board-sam9m10g45ek.c +++ b/arch/arm/mach-at91/board-sam9m10g45ek.c @@ -14,6 +14,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -38,7 +39,6 @@ #include <asm/mach/irq.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/at91sam9_smc.h> #include <mach/at91_shdwc.h> #include <mach/system_rev.h> diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c index 4f14b54b93a8..39a28effc3df 100644 --- a/arch/arm/mach-at91/board-sam9rlek.c +++ b/arch/arm/mach-at91/board-sam9rlek.c @@ -8,6 +8,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -30,7 +31,6 @@ #include <mach/hardware.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/at91sam9_smc.h> #include <mach/at91_shdwc.h> diff --git a/arch/arm/mach-at91/board-usb-a9260.c b/arch/arm/mach-at91/board-usb-a9260.c index 8c4c1a02c4be..bac9b65cf551 100644 --- a/arch/arm/mach-at91/board-usb-a9260.c +++ b/arch/arm/mach-at91/board-usb-a9260.c @@ -21,6 +21,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -40,7 +41,6 @@ #include <mach/hardware.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/at91sam9_smc.h> #include <mach/at91_shdwc.h> diff --git a/arch/arm/mach-at91/board-usb-a9263.c b/arch/arm/mach-at91/board-usb-a9263.c index 25e793782a4e..5bd735787d6d 100644 --- a/arch/arm/mach-at91/board-usb-a9263.c +++ b/arch/arm/mach-at91/board-usb-a9263.c @@ -21,6 +21,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -39,7 +40,6 @@ #include <mach/hardware.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/at91sam9_smc.h> #include <mach/at91_shdwc.h> diff --git a/arch/arm/mach-at91/board-yl-9200.c b/arch/arm/mach-at91/board-yl-9200.c index 95edcbd2aec6..3c288b396fc4 100644 --- a/arch/arm/mach-at91/board-yl-9200.c +++ b/arch/arm/mach-at91/board-yl-9200.c @@ -22,6 +22,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -43,7 +44,6 @@ #include <mach/hardware.h> #include <mach/board.h> -#include <mach/gpio.h> #include <mach/at91rm9200_mc.h> #include <mach/cpu.h> diff --git a/arch/arm/mach-at91/gpio.c b/arch/arm/mach-at91/gpio.c index 4615528205c8..224e9e2f8674 100644 --- a/arch/arm/mach-at91/gpio.c +++ b/arch/arm/mach-at91/gpio.c @@ -11,6 +11,7 @@ #include <linux/clk.h> #include <linux/errno.h> +#include <linux/gpio.h> #include <linux/interrupt.h> #include <linux/irq.h> #include <linux/debugfs.h> @@ -22,9 +23,6 @@ #include <mach/hardware.h> #include <mach/at91_pio.h> -#include <mach/gpio.h> - -#include <asm/gpio.h> #include "generic.h" diff --git a/arch/arm/mach-at91/include/mach/gpio.h b/arch/arm/mach-at91/include/mach/gpio.h index 056dc6674b6b..2b9a1f51210f 100644 --- a/arch/arm/mach-at91/include/mach/gpio.h +++ b/arch/arm/mach-at91/include/mach/gpio.h @@ -214,11 +214,6 @@ extern void at91_gpio_resume(void); */ #include <asm/errno.h> -#include <asm-generic/gpio.h> /* cansleep wrappers */ - -#define gpio_get_value __gpio_get_value -#define gpio_set_value __gpio_set_value -#define gpio_cansleep __gpio_cansleep #define gpio_to_irq(gpio) (gpio) #define irq_to_gpio(irq) (irq) diff --git a/arch/arm/mach-at91/leds.c b/arch/arm/mach-at91/leds.c index 0415a839e1ad..8dfafe76ffe6 100644 --- a/arch/arm/mach-at91/leds.c +++ b/arch/arm/mach-at91/leds.c @@ -9,13 +9,13 @@ * 2 of the License, or (at your option) any later version. */ +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/module.h> #include <linux/init.h> #include <linux/platform_device.h> #include <mach/board.h> -#include <mach/gpio.h> /* ------------------------------------------------------------------------- */ diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c index 4159eca78945..7046158109d7 100644 --- a/arch/arm/mach-at91/pm.c +++ b/arch/arm/mach-at91/pm.c @@ -10,6 +10,7 @@ * (at your option) any later version. */ +#include <linux/gpio.h> #include <linux/suspend.h> #include <linux/sched.h> #include <linux/proc_fs.h> @@ -25,7 +26,6 @@ #include <asm/mach/irq.h> #include <mach/at91_pmc.h> -#include <mach/gpio.h> #include <mach/cpu.h> #include "generic.h" diff --git a/arch/arm/mach-davinci/Makefile b/arch/arm/mach-davinci/Makefile index 0b87a1ca2bb3..495e31306fc0 100644 --- a/arch/arm/mach-davinci/Makefile +++ b/arch/arm/mach-davinci/Makefile @@ -5,7 +5,7 @@ # Common objects obj-y := time.o clock.o serial.o io.o psc.o \ - gpio.o dma.o usb.o common.o sram.o aemif.o + dma.o usb.o common.o sram.o aemif.o obj-$(CONFIG_DAVINCI_MUX) += mux.o @@ -17,7 +17,6 @@ obj-$(CONFIG_ARCH_DAVINCI_DM365) += dm365.o devices.o obj-$(CONFIG_ARCH_DAVINCI_DA830) += da830.o devices-da8xx.o obj-$(CONFIG_ARCH_DAVINCI_DA850) += da850.o devices-da8xx.o obj-$(CONFIG_ARCH_DAVINCI_TNETV107X) += tnetv107x.o devices-tnetv107x.o -obj-$(CONFIG_ARCH_DAVINCI_TNETV107X) += gpio-tnetv107x.o obj-$(CONFIG_AINTC) += irq.o obj-$(CONFIG_CP_INTC) += cp_intc.o diff --git a/arch/arm/mach-davinci/da830.c b/arch/arm/mach-davinci/da830.c index 2ed2f822fc40..a6bf5dcaef13 100644 --- a/arch/arm/mach-davinci/da830.c +++ b/arch/arm/mach-davinci/da830.c @@ -8,6 +8,7 @@ * is licensed "as is" without any warranty of any kind, whether express * or implied. */ +#include <linux/gpio.h> #include <linux/init.h> #include <linux/clk.h> @@ -19,7 +20,7 @@ #include <mach/common.h> #include <mach/time.h> #include <mach/da8xx.h> -#include <mach/gpio.h> +#include <mach/gpio-davinci.h> #include "clock.h" #include "mux.h" diff --git a/arch/arm/mach-davinci/da850.c b/arch/arm/mach-davinci/da850.c index 935dbed5c541..4aae01576aab 100644 --- a/arch/arm/mach-davinci/da850.c +++ b/arch/arm/mach-davinci/da850.c @@ -11,6 +11,7 @@ * is licensed "as is" without any warranty of any kind, whether express * or implied. */ +#include <linux/gpio.h> #include <linux/init.h> #include <linux/clk.h> #include <linux/platform_device.h> @@ -27,7 +28,7 @@ #include <mach/da8xx.h> #include <mach/cpufreq.h> #include <mach/pm.h> -#include <mach/gpio.h> +#include <mach/gpio-davinci.h> #include "clock.h" #include "mux.h" diff --git a/arch/arm/mach-davinci/dm355.c b/arch/arm/mach-davinci/dm355.c index a3a94e9c9378..c143f43addcc 100644 --- a/arch/arm/mach-davinci/dm355.c +++ b/arch/arm/mach-davinci/dm355.c @@ -13,7 +13,6 @@ #include <linux/serial_8250.h> #include <linux/platform_device.h> #include <linux/dma-mapping.h> -#include <linux/gpio.h> #include <linux/spi/spi.h> @@ -30,6 +29,7 @@ #include <mach/common.h> #include <mach/asp.h> #include <mach/spi.h> +#include <mach/gpio-davinci.h> #include "clock.h" #include "mux.h" diff --git a/arch/arm/mach-davinci/dm365.c b/arch/arm/mach-davinci/dm365.c index 4604e72d7d99..679e168dce34 100644 --- a/arch/arm/mach-davinci/dm365.c +++ b/arch/arm/mach-davinci/dm365.c @@ -17,7 +17,6 @@ #include <linux/serial_8250.h> #include <linux/platform_device.h> #include <linux/dma-mapping.h> -#include <linux/gpio.h> #include <linux/spi/spi.h> #include <asm/mach/map.h> @@ -34,7 +33,7 @@ #include <mach/asp.h> #include <mach/keyscan.h> #include <mach/spi.h> - +#include <mach/gpio-davinci.h> #include "clock.h" #include "mux.h" diff --git a/arch/arm/mach-davinci/dm644x.c b/arch/arm/mach-davinci/dm644x.c index 4c82c2716293..9a274665edc5 100644 --- a/arch/arm/mach-davinci/dm644x.c +++ b/arch/arm/mach-davinci/dm644x.c @@ -12,7 +12,6 @@ #include <linux/clk.h> #include <linux/serial_8250.h> #include <linux/platform_device.h> -#include <linux/gpio.h> #include <asm/mach/map.h> @@ -26,6 +25,7 @@ #include <mach/serial.h> #include <mach/common.h> #include <mach/asp.h> +#include <mach/gpio-davinci.h> #include "clock.h" #include "mux.h" diff --git a/arch/arm/mach-davinci/dm646x.c b/arch/arm/mach-davinci/dm646x.c index 1802e711a2b8..03e5f4931b42 100644 --- a/arch/arm/mach-davinci/dm646x.c +++ b/arch/arm/mach-davinci/dm646x.c @@ -13,7 +13,6 @@ #include <linux/clk.h> #include <linux/serial_8250.h> #include <linux/platform_device.h> -#include <linux/gpio.h> #include <asm/mach/map.h> @@ -27,6 +26,7 @@ #include <mach/serial.h> #include <mach/common.h> #include <mach/asp.h> +#include <mach/gpio-davinci.h> #include "clock.h" #include "mux.h" diff --git a/arch/arm/mach-davinci/include/mach/gpio-davinci.h b/arch/arm/mach-davinci/include/mach/gpio-davinci.h new file mode 100644 index 000000000000..1fdd1fd35448 --- /dev/null +++ b/arch/arm/mach-davinci/include/mach/gpio-davinci.h @@ -0,0 +1,91 @@ +/* + * TI DaVinci GPIO Support + * + * Copyright (c) 2006 David Brownell + * Copyright (c) 2007, MontaVista Software, Inc. <source@mvista.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef __DAVINCI_DAVINCI_GPIO_H +#define __DAVINCI_DAVINCI_GPIO_H + +#include <linux/io.h> +#include <linux/spinlock.h> + +#include <asm-generic/gpio.h> + +#include <mach/irqs.h> +#include <mach/common.h> + +#define DAVINCI_GPIO_BASE 0x01C67000 + +enum davinci_gpio_type { + GPIO_TYPE_DAVINCI = 0, + GPIO_TYPE_TNETV107X, +}; + +/* + * basic gpio routines + * + * board-specific init should be done by arch/.../.../board-XXX.c (maybe + * initializing banks together) rather than boot loaders; kexec() won't + * go through boot loaders. + * + * the gpio clock will be turned on when gpios are used, and you may also + * need to pay attention to PINMUX registers to be sure those pins are + * used as gpios, not with other peripherals. + * + * On-chip GPIOs are numbered 0..(DAVINCI_N_GPIO-1). For documentation, + * and maybe for later updates, code may write GPIO(N). These may be + * all 1.8V signals, all 3.3V ones, or a mix of the two. A given chip + * may not support all the GPIOs in that range. + * + * GPIOs can also be on external chips, numbered after the ones built-in + * to the DaVinci chip. For now, they won't be usable as IRQ sources. + */ +#define GPIO(X) (X) /* 0 <= X <= (DAVINCI_N_GPIO - 1) */ + +/* Convert GPIO signal to GPIO pin number */ +#define GPIO_TO_PIN(bank, gpio) (16 * (bank) + (gpio)) + +struct davinci_gpio_controller { + struct gpio_chip chip; + int irq_base; + spinlock_t lock; + void __iomem *regs; + void __iomem *set_data; + void __iomem *clr_data; + void __iomem *in_data; +}; + +/* The __gpio_to_controller() and __gpio_mask() functions inline to constants + * with constant parameters; or in outlined code they execute at runtime. + * + * You'd access the controller directly when reading or writing more than + * one gpio value at a time, and to support wired logic where the value + * being driven by the cpu need not match the value read back. + * + * These are NOT part of the cross-platform GPIO interface + */ +static inline struct davinci_gpio_controller * +__gpio_to_controller(unsigned gpio) +{ + struct davinci_gpio_controller *ctlrs = davinci_soc_info.gpio_ctlrs; + int index = gpio / 32; + + if (!ctlrs || index >= davinci_soc_info.gpio_ctlrs_num) + return NULL; + + return ctlrs + index; +} + +static inline u32 __gpio_mask(unsigned gpio) +{ + return 1 << (gpio % 32); +} + +#endif /* __DAVINCI_DAVINCI_GPIO_H */ diff --git a/arch/arm/mach-davinci/include/mach/gpio.h b/arch/arm/mach-davinci/include/mach/gpio.h index fbece126c2bf..fbaae4772b91 100644 --- a/arch/arm/mach-davinci/include/mach/gpio.h +++ b/arch/arm/mach-davinci/include/mach/gpio.h @@ -13,80 +13,10 @@ #ifndef __DAVINCI_GPIO_H #define __DAVINCI_GPIO_H -#include <linux/io.h> -#include <linux/spinlock.h> - #include <asm-generic/gpio.h> -#include <mach/irqs.h> -#include <mach/common.h> - -#define DAVINCI_GPIO_BASE 0x01C67000 - -enum davinci_gpio_type { - GPIO_TYPE_DAVINCI = 0, - GPIO_TYPE_TNETV107X, -}; - -/* - * basic gpio routines - * - * board-specific init should be done by arch/.../.../board-XXX.c (maybe - * initializing banks together) rather than boot loaders; kexec() won't - * go through boot loaders. - * - * the gpio clock will be turned on when gpios are used, and you may also - * need to pay attention to PINMUX registers to be sure those pins are - * used as gpios, not with other peripherals. - * - * On-chip GPIOs are numbered 0..(DAVINCI_N_GPIO-1). For documentation, - * and maybe for later updates, code may write GPIO(N). These may be - * all 1.8V signals, all 3.3V ones, or a mix of the two. A given chip - * may not support all the GPIOs in that range. - * - * GPIOs can also be on external chips, numbered after the ones built-in - * to the DaVinci chip. For now, they won't be usable as IRQ sources. - */ -#define GPIO(X) (X) /* 0 <= X <= (DAVINCI_N_GPIO - 1) */ - -/* Convert GPIO signal to GPIO pin number */ -#define GPIO_TO_PIN(bank, gpio) (16 * (bank) + (gpio)) - -struct davinci_gpio_controller { - struct gpio_chip chip; - int irq_base; - spinlock_t lock; - void __iomem *regs; - void __iomem *set_data; - void __iomem *clr_data; - void __iomem *in_data; -}; - -/* The __gpio_to_controller() and __gpio_mask() functions inline to constants - * with constant parameters; or in outlined code they execute at runtime. - * - * You'd access the controller directly when reading or writing more than - * one gpio value at a time, and to support wired logic where the value - * being driven by the cpu need not match the value read back. - * - * These are NOT part of the cross-platform GPIO interface - */ -static inline struct davinci_gpio_controller * -__gpio_to_controller(unsigned gpio) -{ - struct davinci_gpio_controller *ctlrs = davinci_soc_info.gpio_ctlrs; - int index = gpio / 32; - - if (!ctlrs || index >= davinci_soc_info.gpio_ctlrs_num) - return NULL; - - return ctlrs + index; -} - -static inline u32 __gpio_mask(unsigned gpio) -{ - return 1 << (gpio % 32); -} +/* The inline versions use the static inlines in the driver header */ +#include "gpio-davinci.h" /* * The get/set/clear functions will inline when called with constant @@ -147,11 +77,6 @@ static inline int gpio_cansleep(unsigned gpio) return __gpio_cansleep(gpio); } -static inline int gpio_to_irq(unsigned gpio) -{ - return __gpio_to_irq(gpio); -} - static inline int irq_to_gpio(unsigned irq) { /* don't support the reverse mapping */ diff --git a/arch/arm/mach-davinci/tnetv107x.c b/arch/arm/mach-davinci/tnetv107x.c index 1b28fdd892a6..409bb869c7c7 100644 --- a/arch/arm/mach-davinci/tnetv107x.c +++ b/arch/arm/mach-davinci/tnetv107x.c @@ -12,6 +12,7 @@ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. */ +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/clk.h> @@ -27,9 +28,9 @@ #include <mach/psc.h> #include <mach/cp_intc.h> #include <mach/irqs.h> -#include <mach/gpio.h> #include <mach/hardware.h> #include <mach/tnetv107x.h> +#include <mach/gpio-davinci.h> #include "clock.h" #include "mux.h" diff --git a/arch/arm/mach-ebsa110/include/mach/io.h b/arch/arm/mach-ebsa110/include/mach/io.h index f68daa632af0..44679db672fb 100644 --- a/arch/arm/mach-ebsa110/include/mach/io.h +++ b/arch/arm/mach-ebsa110/include/mach/io.h @@ -13,8 +13,6 @@ #ifndef __ASM_ARM_ARCH_IO_H #define __ASM_ARM_ARCH_IO_H -#define IO_SPACE_LIMIT 0xffff - u8 __inb8(unsigned int port); void __outb8(u8 val, unsigned int port); diff --git a/arch/arm/mach-ep93xx/core.c b/arch/arm/mach-ep93xx/core.c index c60f081e930b..94c78bc66275 100644 --- a/arch/arm/mach-ep93xx/core.c +++ b/arch/arm/mach-ep93xx/core.c @@ -38,6 +38,7 @@ #include <mach/fb.h> #include <mach/ep93xx_keypad.h> #include <mach/ep93xx_spi.h> +#include <mach/gpio-ep93xx.h> #include <asm/mach/map.h> #include <asm/mach/time.h> diff --git a/arch/arm/mach-ep93xx/edb93xx.c b/arch/arm/mach-ep93xx/edb93xx.c index 257175edc575..c63a5ec1a8e3 100644 --- a/arch/arm/mach-ep93xx/edb93xx.c +++ b/arch/arm/mach-ep93xx/edb93xx.c @@ -37,6 +37,7 @@ #include <mach/hardware.h> #include <mach/fb.h> #include <mach/ep93xx_spi.h> +#include <mach/gpio-ep93xx.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> diff --git a/arch/arm/mach-ep93xx/include/mach/gpio.h b/arch/arm/mach-ep93xx/include/mach/gpio-ep93xx.h index c57152c231f1..8aff2ea35877 100644 --- a/arch/arm/mach-ep93xx/include/mach/gpio.h +++ b/arch/arm/mach-ep93xx/include/mach/gpio-ep93xx.h @@ -1,9 +1,7 @@ -/* - * arch/arm/mach-ep93xx/include/mach/gpio.h - */ +/* Include file for the EP93XX GPIO controller machine specifics */ -#ifndef __ASM_ARCH_GPIO_H -#define __ASM_ARCH_GPIO_H +#ifndef __GPIO_EP93XX_H +#define __GPIO_EP93XX_H /* GPIO port A. */ #define EP93XX_GPIO_LINE_A(x) ((x) + 0) @@ -99,22 +97,4 @@ /* maximum value for irq capable line identifiers */ #define EP93XX_GPIO_LINE_MAX_IRQ EP93XX_GPIO_LINE_F(7) -/* new generic GPIO API - see Documentation/gpio.txt */ - -#include <asm-generic/gpio.h> - -#define gpio_get_value __gpio_get_value -#define gpio_set_value __gpio_set_value -#define gpio_cansleep __gpio_cansleep - -/* - * Map GPIO A0..A7 (0..7) to irq 64..71, - * B0..B7 (7..15) to irq 72..79, and - * F0..F7 (16..24) to irq 80..87. - */ -#define gpio_to_irq(gpio) \ - (((gpio) <= EP93XX_GPIO_LINE_MAX_IRQ) ? (64 + (gpio)) : -EINVAL) - -#define irq_to_gpio(irq) ((irq) - gpio_to_irq(0)) - -#endif +#endif /* __GPIO_EP93XX_H */ diff --git a/arch/arm/mach-ep93xx/simone.c b/arch/arm/mach-ep93xx/simone.c index 238bc603da86..d6f286b4db9c 100644 --- a/arch/arm/mach-ep93xx/simone.c +++ b/arch/arm/mach-ep93xx/simone.c @@ -18,12 +18,12 @@ #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> -#include <linux/gpio.h> #include <linux/i2c.h> #include <linux/i2c-gpio.h> #include <mach/hardware.h> #include <mach/fb.h> +#include <mach/gpio-ep93xx.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> diff --git a/arch/arm/mach-ep93xx/snappercl15.c b/arch/arm/mach-ep93xx/snappercl15.c index 3bdf3a2e5ad0..2b4d4b0201df 100644 --- a/arch/arm/mach-ep93xx/snappercl15.c +++ b/arch/arm/mach-ep93xx/snappercl15.c @@ -20,7 +20,6 @@ #include <linux/kernel.h> #include <linux/init.h> #include <linux/io.h> -#include <linux/gpio.h> #include <linux/i2c.h> #include <linux/i2c-gpio.h> #include <linux/fb.h> @@ -30,6 +29,7 @@ #include <mach/hardware.h> #include <mach/fb.h> +#include <mach/gpio-ep93xx.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> diff --git a/arch/arm/mach-exynos4/include/mach/gpio.h b/arch/arm/mach-exynos4/include/mach/gpio.h index be9266b10fdb..80523ca9bb49 100644 --- a/arch/arm/mach-exynos4/include/mach/gpio.h +++ b/arch/arm/mach-exynos4/include/mach/gpio.h @@ -13,11 +13,6 @@ #ifndef __ASM_ARCH_GPIO_H #define __ASM_ARCH_GPIO_H __FILE__ -#define gpio_get_value __gpio_get_value -#define gpio_set_value __gpio_set_value -#define gpio_cansleep __gpio_cansleep -#define gpio_to_irq __gpio_to_irq - /* Practically, GPIO banks up to GPZ are the configurable gpio banks */ /* GPIO bank sizes */ @@ -151,6 +146,4 @@ enum s5p_gpio_number { #define ARCH_NR_GPIOS (EXYNOS4_GPZ(EXYNOS4_GPIO_Z_NR) + \ CONFIG_SAMSUNG_GPIO_EXTRA + 1) -#include <asm-generic/gpio.h> - #endif /* __ASM_ARCH_GPIO_H */ diff --git a/arch/arm/mach-footbridge/include/mach/io.h b/arch/arm/mach-footbridge/include/mach/io.h index 32e4cc397c28..15a70396c27d 100644 --- a/arch/arm/mach-footbridge/include/mach/io.h +++ b/arch/arm/mach-footbridge/include/mach/io.h @@ -23,8 +23,6 @@ #define PCIO_SIZE 0x00100000 #define PCIO_BASE MMU_IO(0xff000000, 0x7c000000) -#define IO_SPACE_LIMIT 0xffff - /* * Translation of various region addresses to virtual addresses */ diff --git a/arch/arm/mach-gemini/include/mach/gpio.h b/arch/arm/mach-gemini/include/mach/gpio.h index 3bc2c70f2989..40a0527bada7 100644 --- a/arch/arm/mach-gemini/include/mach/gpio.h +++ b/arch/arm/mach-gemini/include/mach/gpio.h @@ -13,11 +13,6 @@ #define __MACH_GPIO_H__ #include <mach/irqs.h> -#include <asm-generic/gpio.h> - -#define gpio_get_value __gpio_get_value -#define gpio_set_value __gpio_set_value -#define gpio_cansleep __gpio_cansleep #define gpio_to_irq(x) ((x) + GPIO_IRQ_BASE) #define irq_to_gpio(x) ((x) - GPIO_IRQ_BASE) diff --git a/arch/arm/mach-highbank/Makefile b/arch/arm/mach-highbank/Makefile new file mode 100644 index 000000000000..986958a5a720 --- /dev/null +++ b/arch/arm/mach-highbank/Makefile @@ -0,0 +1,6 @@ +obj-y := clock.o highbank.o system.o +obj-$(CONFIG_DEBUG_HIGHBANK_UART) += lluart.o +obj-$(CONFIG_SMP) += platsmp.o +obj-$(CONFIG_LOCAL_TIMERS) += localtimer.o +obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o +obj-$(CONFIG_PM_SLEEP) += pm.o diff --git a/arch/arm/mach-highbank/Makefile.boot b/arch/arm/mach-highbank/Makefile.boot new file mode 100644 index 000000000000..dae9661a7689 --- /dev/null +++ b/arch/arm/mach-highbank/Makefile.boot @@ -0,0 +1 @@ +zreladdr-y := 0x00008000 diff --git a/arch/arm/mach-highbank/clock.c b/arch/arm/mach-highbank/clock.c new file mode 100644 index 000000000000..c25a2ae4fde1 --- /dev/null +++ b/arch/arm/mach-highbank/clock.c @@ -0,0 +1,62 @@ +/* + * Copyright 2011 Calxeda, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/errno.h> +#include <linux/clk.h> +#include <linux/clkdev.h> + +struct clk { + unsigned long rate; +}; + +int clk_enable(struct clk *clk) +{ + return 0; +} + +void clk_disable(struct clk *clk) +{} + +unsigned long clk_get_rate(struct clk *clk) +{ + return clk->rate; +} + +long clk_round_rate(struct clk *clk, unsigned long rate) +{ + return clk->rate; +} + +int clk_set_rate(struct clk *clk, unsigned long rate) +{ + return 0; +} + +static struct clk eclk = { .rate = 200000000 }; +static struct clk pclk = { .rate = 150000000 }; + +static struct clk_lookup lookups[] = { + { .clk = &pclk, .con_id = "apb_pclk", }, + { .clk = &pclk, .dev_id = "sp804", }, + { .clk = &eclk, .dev_id = "ffe0e000.sdhci", }, + { .clk = &pclk, .dev_id = "fff36000.serial", }, +}; + +void __init highbank_clocks_init(void) +{ + clkdev_add_table(lookups, ARRAY_SIZE(lookups)); +} diff --git a/arch/arm/mach-highbank/core.h b/arch/arm/mach-highbank/core.h new file mode 100644 index 000000000000..7e33fc94cd1e --- /dev/null +++ b/arch/arm/mach-highbank/core.h @@ -0,0 +1,9 @@ +extern void highbank_set_cpu_jump(int cpu, void *jump_addr); +extern void highbank_clocks_init(void); +extern void __iomem *scu_base_addr; +#ifdef CONFIG_DEBUG_HIGHBANK_UART +extern void highbank_lluart_map_io(void); +#else +static inline void highbank_lluart_map_io(void) {} +#endif + diff --git a/arch/arm/mach-highbank/highbank.c b/arch/arm/mach-highbank/highbank.c new file mode 100644 index 000000000000..b82dcf08e747 --- /dev/null +++ b/arch/arm/mach-highbank/highbank.c @@ -0,0 +1,145 @@ +/* + * Copyright 2010-2011 Calxeda, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include <linux/clk.h> +#include <linux/clkdev.h> +#include <linux/io.h> +#include <linux/irq.h> +#include <linux/irqdomain.h> +#include <linux/of.h> +#include <linux/of_irq.h> +#include <linux/of_platform.h> +#include <linux/of_address.h> + +#include <asm/cacheflush.h> +#include <asm/unified.h> +#include <asm/smp_scu.h> +#include <asm/hardware/arm_timer.h> +#include <asm/hardware/timer-sp.h> +#include <asm/hardware/gic.h> +#include <asm/hardware/cache-l2x0.h> +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/time.h> +#include <mach/irqs.h> + +#include "core.h" +#include "sysregs.h" + +void __iomem *sregs_base; + +#define HB_SCU_VIRT_BASE 0xfee00000 +void __iomem *scu_base_addr = ((void __iomem *)(HB_SCU_VIRT_BASE)); + +static struct map_desc scu_io_desc __initdata = { + .virtual = HB_SCU_VIRT_BASE, + .pfn = 0, /* run-time */ + .length = SZ_4K, + .type = MT_DEVICE, +}; + +static void __init highbank_scu_map_io(void) +{ + unsigned long base; + + /* Get SCU base */ + asm("mrc p15, 4, %0, c15, c0, 0" : "=r" (base)); + + scu_io_desc.pfn = __phys_to_pfn(base); + iotable_init(&scu_io_desc, 1); +} + +static void __init highbank_map_io(void) +{ + highbank_scu_map_io(); + highbank_lluart_map_io(); +} + +#define HB_JUMP_TABLE_PHYS(cpu) (0x40 + (0x10 * (cpu))) +#define HB_JUMP_TABLE_VIRT(cpu) phys_to_virt(HB_JUMP_TABLE_PHYS(cpu)) + +void highbank_set_cpu_jump(int cpu, void *jump_addr) +{ + writel(BSYM(virt_to_phys(jump_addr)), HB_JUMP_TABLE_VIRT(cpu)); + __cpuc_flush_dcache_area(HB_JUMP_TABLE_VIRT(cpu), 16); + outer_clean_range(HB_JUMP_TABLE_PHYS(cpu), + HB_JUMP_TABLE_PHYS(cpu) + 15); +} + +const static struct of_device_id irq_match[] = { + { .compatible = "arm,cortex-a9-gic", .data = gic_of_init, }, + {} +}; + +static void __init highbank_init_irq(void) +{ + of_irq_init(irq_match); + l2x0_of_init(0, ~0UL); +} + +static void __init highbank_timer_init(void) +{ + int irq; + struct device_node *np; + void __iomem *timer_base; + + /* Map system registers */ + np = of_find_compatible_node(NULL, NULL, "calxeda,hb-sregs"); + sregs_base = of_iomap(np, 0); + WARN_ON(!sregs_base); + + np = of_find_compatible_node(NULL, NULL, "arm,sp804"); + timer_base = of_iomap(np, 0); + WARN_ON(!timer_base); + irq = irq_of_parse_and_map(np, 0); + + highbank_clocks_init(); + + sp804_clocksource_init(timer_base + 0x20, "timer1"); + sp804_clockevents_init(timer_base, irq, "timer0"); +} + +static struct sys_timer highbank_timer = { + .init = highbank_timer_init, +}; + +static void highbank_power_off(void) +{ + hignbank_set_pwr_shutdown(); + scu_power_mode(scu_base_addr, SCU_PM_POWEROFF); + + while (1) + cpu_do_idle(); +} + +static void __init highbank_init(void) +{ + pm_power_off = highbank_power_off; + + of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL); +} + +static const char *highbank_match[] __initconst = { + "calxeda,highbank", + NULL, +}; + +DT_MACHINE_START(HIGHBANK, "Highbank") + .map_io = highbank_map_io, + .init_irq = highbank_init_irq, + .timer = &highbank_timer, + .init_machine = highbank_init, + .dt_compat = highbank_match, +MACHINE_END diff --git a/arch/arm/mach-highbank/hotplug.c b/arch/arm/mach-highbank/hotplug.c new file mode 100644 index 000000000000..977cebbea580 --- /dev/null +++ b/arch/arm/mach-highbank/hotplug.c @@ -0,0 +1,56 @@ +/* + * Copyright 2011 Calxeda, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include <linux/kernel.h> +#include <linux/errno.h> +#include <linux/smp.h> + +#include <asm/smp_scu.h> +#include <asm/cacheflush.h> + +#include "core.h" + +extern void secondary_startup(void); + +int platform_cpu_kill(unsigned int cpu) +{ + return 1; +} + +/* + * platform-specific code to shutdown a CPU + * + */ +void platform_cpu_die(unsigned int cpu) +{ + flush_cache_all(); + + highbank_set_cpu_jump(cpu, secondary_startup); + scu_power_mode(scu_base_addr, SCU_PM_POWEROFF); + + cpu_do_idle(); + + /* We should never return from idle */ + panic("highbank: cpu %d unexpectedly exit from shutdown\n", cpu); +} + +int platform_cpu_disable(unsigned int cpu) +{ + /* + * CPU0 should not be shut down via hotplug. cpu_idle can WFI + * or a proper shutdown or hibernate should be used. + */ + return cpu == 0 ? -EPERM : 0; +} diff --git a/arch/arm/mach-highbank/include/mach/debug-macro.S b/arch/arm/mach-highbank/include/mach/debug-macro.S new file mode 100644 index 000000000000..cb57fe5bcd04 --- /dev/null +++ b/arch/arm/mach-highbank/include/mach/debug-macro.S @@ -0,0 +1,19 @@ +/* + * Debugging macro include header + * + * Copyright (C) 1994-1999 Russell King + * Moved from linux/arch/arm/kernel/debug.S by Ben Dooks + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + + .macro addruart,rp,rv,tmp + movw \rv, #0x6000 + movt \rv, #0xfee3 + movw \rp, #0x6000 + movt \rp, #0xfff3 + .endm + +#include <asm/hardware/debug-pl01x.S> diff --git a/arch/arm/mach-highbank/include/mach/entry-macro.S b/arch/arm/mach-highbank/include/mach/entry-macro.S new file mode 100644 index 000000000000..73c11297509e --- /dev/null +++ b/arch/arm/mach-highbank/include/mach/entry-macro.S @@ -0,0 +1,7 @@ +#include <asm/hardware/entry-macro-gic.S> + + .macro disable_fiq + .endm + + .macro arch_ret_to_user, tmp1, tmp2 + .endm diff --git a/arch/arm/mach-highbank/include/mach/gpio.h b/arch/arm/mach-highbank/include/mach/gpio.h new file mode 100644 index 000000000000..40a8c178f10d --- /dev/null +++ b/arch/arm/mach-highbank/include/mach/gpio.h @@ -0,0 +1 @@ +/* empty */ diff --git a/arch/arm/mach-highbank/include/mach/io.h b/arch/arm/mach-highbank/include/mach/io.h new file mode 100644 index 000000000000..70cfa3ba7697 --- /dev/null +++ b/arch/arm/mach-highbank/include/mach/io.h @@ -0,0 +1,7 @@ +#ifndef __MACH_IO_H +#define __MACH_IO_H + +#define __io(a) ({ (void)(a); __typesafe_io(0); }) +#define __mem_pci(a) (a) + +#endif diff --git a/arch/arm/mach-highbank/include/mach/irqs.h b/arch/arm/mach-highbank/include/mach/irqs.h new file mode 100644 index 000000000000..9746aab14e9a --- /dev/null +++ b/arch/arm/mach-highbank/include/mach/irqs.h @@ -0,0 +1,6 @@ +#ifndef __MACH_IRQS_H +#define __MACH_IRQS_H + +#define NR_IRQS 192 + +#endif diff --git a/arch/arm/mach-highbank/include/mach/memory.h b/arch/arm/mach-highbank/include/mach/memory.h new file mode 100644 index 000000000000..40a8c178f10d --- /dev/null +++ b/arch/arm/mach-highbank/include/mach/memory.h @@ -0,0 +1 @@ +/* empty */ diff --git a/arch/arm/mach-highbank/include/mach/system.h b/arch/arm/mach-highbank/include/mach/system.h new file mode 100644 index 000000000000..7e8192296cae --- /dev/null +++ b/arch/arm/mach-highbank/include/mach/system.h @@ -0,0 +1,26 @@ +/* + * Copyright 2010-2011 Calxeda, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ +#ifndef __MACH_SYSTEM_H +#define __MACH_SYSTEM_H + +static inline void arch_idle(void) +{ + cpu_do_idle(); +} + +extern void arch_reset(char mode, const char *cmd); + +#endif diff --git a/arch/arm/mach-highbank/include/mach/timex.h b/arch/arm/mach-highbank/include/mach/timex.h new file mode 100644 index 000000000000..88dac7a55a97 --- /dev/null +++ b/arch/arm/mach-highbank/include/mach/timex.h @@ -0,0 +1,6 @@ +#ifndef __MACH_TIMEX_H +#define __MACH_TIMEX_H + +#define CLOCK_TICK_RATE 1000000 + +#endif diff --git a/arch/arm/mach-highbank/include/mach/uncompress.h b/arch/arm/mach-highbank/include/mach/uncompress.h new file mode 100644 index 000000000000..bbe20e696325 --- /dev/null +++ b/arch/arm/mach-highbank/include/mach/uncompress.h @@ -0,0 +1,9 @@ +#ifndef __MACH_UNCOMPRESS_H +#define __MACH_UNCOMPRESS_H + +#define putc(c) +#define flush() +#define arch_decomp_setup() +#define arch_decomp_wdog() + +#endif diff --git a/arch/arm/mach-highbank/include/mach/vmalloc.h b/arch/arm/mach-highbank/include/mach/vmalloc.h new file mode 100644 index 000000000000..1969e954277a --- /dev/null +++ b/arch/arm/mach-highbank/include/mach/vmalloc.h @@ -0,0 +1 @@ +#define VMALLOC_END 0xFEE00000UL diff --git a/arch/arm/mach-highbank/lluart.c b/arch/arm/mach-highbank/lluart.c new file mode 100644 index 000000000000..371575019f33 --- /dev/null +++ b/arch/arm/mach-highbank/lluart.c @@ -0,0 +1,34 @@ +/* + * Copyright 2011 Calxeda, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include <linux/init.h> +#include <asm/page.h> +#include <asm/sizes.h> +#include <asm/mach/map.h> + +#define HB_DEBUG_LL_PHYS_BASE 0xfff36000 +#define HB_DEBUG_LL_VIRT_BASE 0xfee36000 + +static struct map_desc lluart_io_desc __initdata = { + .virtual = HB_DEBUG_LL_VIRT_BASE, + .pfn = __phys_to_pfn(HB_DEBUG_LL_PHYS_BASE), + .length = SZ_4K, + .type = MT_DEVICE, +}; + +void __init highbank_lluart_map_io(void) +{ + iotable_init(&lluart_io_desc, 1); +} diff --git a/arch/arm/mach-highbank/localtimer.c b/arch/arm/mach-highbank/localtimer.c new file mode 100644 index 000000000000..5a00e7945fdf --- /dev/null +++ b/arch/arm/mach-highbank/localtimer.c @@ -0,0 +1,40 @@ +/* + * Copyright 2010-2011 Calxeda, Inc. + * Based on localtimer.c, Copyright (C) 2002 ARM Ltd. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include <linux/init.h> +#include <linux/clockchips.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_irq.h> + +#include <asm/smp_twd.h> + +/* + * Setup the local clock events for a CPU. + */ +int __cpuinit local_timer_setup(struct clock_event_device *evt) +{ + struct device_node *np; + + np = of_find_compatible_node(NULL, NULL, "arm,smp-twd"); + if (!twd_base) { + twd_base = of_iomap(np, 0); + WARN_ON(!twd_base); + } + evt->irq = irq_of_parse_and_map(np, 0); + twd_timer_setup(evt); + return 0; +} diff --git a/arch/arm/mach-highbank/platsmp.c b/arch/arm/mach-highbank/platsmp.c new file mode 100644 index 000000000000..d01364c72b45 --- /dev/null +++ b/arch/arm/mach-highbank/platsmp.c @@ -0,0 +1,78 @@ +/* + * Copyright 2010-2011 Calxeda, Inc. + * Based on platsmp.c, Copyright (C) 2002 ARM Ltd. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include <linux/init.h> +#include <linux/smp.h> +#include <linux/io.h> + +#include <asm/smp_scu.h> +#include <asm/hardware/gic.h> + +#include "core.h" + +extern void secondary_startup(void); + +void __cpuinit platform_secondary_init(unsigned int cpu) +{ + gic_secondary_init(0); +} + +int __cpuinit boot_secondary(unsigned int cpu, struct task_struct *idle) +{ + gic_raise_softirq(cpumask_of(cpu), 0); + return 0; +} + +/* + * Initialise the CPU possible map early - this describes the CPUs + * which may be present or become present in the system. + */ +void __init smp_init_cpus(void) +{ + unsigned int i, ncores; + + ncores = scu_get_core_count(scu_base_addr); + + /* sanity check */ + if (ncores > NR_CPUS) { + printk(KERN_WARNING + "highbank: no. of cores (%d) greater than configured " + "maximum of %d - clipping\n", + ncores, NR_CPUS); + ncores = NR_CPUS; + } + + for (i = 0; i < ncores; i++) + set_cpu_possible(i, true); + + set_smp_cross_call(gic_raise_softirq); +} + +void __init platform_smp_prepare_cpus(unsigned int max_cpus) +{ + int i; + + scu_enable(scu_base_addr); + + /* + * Write the address of secondary startup into the jump table + * The cores are in wfi and wait until they receive a soft interrupt + * and a non-zero value to jump to. Then the secondary CPU branches + * to this address. + */ + for (i = 1; i < max_cpus; i++) + highbank_set_cpu_jump(i, secondary_startup); +} diff --git a/arch/arm/mach-highbank/pm.c b/arch/arm/mach-highbank/pm.c new file mode 100644 index 000000000000..33b3beb89982 --- /dev/null +++ b/arch/arm/mach-highbank/pm.c @@ -0,0 +1,55 @@ +/* + * Copyright 2011 Calxeda, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include <linux/init.h> +#include <linux/io.h> +#include <linux/suspend.h> + +#include <asm/proc-fns.h> +#include <asm/smp_scu.h> +#include <asm/suspend.h> + +#include "core.h" +#include "sysregs.h" + +static int highbank_suspend_finish(unsigned long val) +{ + cpu_do_idle(); + return 0; +} + +static int highbank_pm_enter(suspend_state_t state) +{ + hignbank_set_pwr_suspend(); + highbank_set_cpu_jump(0, cpu_resume); + + scu_power_mode(scu_base_addr, SCU_PM_POWEROFF); + cpu_suspend(0, highbank_suspend_finish); + + return 0; +} + +static const struct platform_suspend_ops highbank_pm_ops = { + .enter = highbank_pm_enter, + .valid = suspend_valid_only_mem, +}; + +static int __init highbank_pm_init(void) +{ + suspend_set_ops(&highbank_pm_ops); + return 0; +} +module_init(highbank_pm_init); diff --git a/arch/arm/mach-highbank/sysregs.h b/arch/arm/mach-highbank/sysregs.h new file mode 100644 index 000000000000..0e913389f445 --- /dev/null +++ b/arch/arm/mach-highbank/sysregs.h @@ -0,0 +1,52 @@ +/* + * Copyright 2011 Calxeda, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ +#ifndef _MACH_HIGHBANK__SYSREGS_H_ +#define _MACH_HIGHBANK__SYSREGS_H_ + +#include <linux/io.h> + +extern void __iomem *sregs_base; + +#define HB_SREG_A9_PWR_REQ 0xf00 +#define HB_SREG_A9_BOOT_STAT 0xf04 +#define HB_SREG_A9_BOOT_DATA 0xf08 + +#define HB_PWR_SUSPEND 0 +#define HB_PWR_SOFT_RESET 1 +#define HB_PWR_HARD_RESET 2 +#define HB_PWR_SHUTDOWN 3 + +static inline void hignbank_set_pwr_suspend(void) +{ + writel(HB_PWR_SUSPEND, sregs_base + HB_SREG_A9_PWR_REQ); +} + +static inline void hignbank_set_pwr_shutdown(void) +{ + writel(HB_PWR_SHUTDOWN, sregs_base + HB_SREG_A9_PWR_REQ); +} + +static inline void hignbank_set_pwr_soft_reset(void) +{ + writel(HB_PWR_SOFT_RESET, sregs_base + HB_SREG_A9_PWR_REQ); +} + +static inline void hignbank_set_pwr_hard_reset(void) +{ + writel(HB_PWR_HARD_RESET, sregs_base + HB_SREG_A9_PWR_REQ); +} + +#endif diff --git a/arch/arm/mach-highbank/system.c b/arch/arm/mach-highbank/system.c new file mode 100644 index 000000000000..53f0c4c5ef1c --- /dev/null +++ b/arch/arm/mach-highbank/system.c @@ -0,0 +1,33 @@ +/* + * Copyright 2011 Calxeda, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include <linux/io.h> +#include <asm/smp_scu.h> +#include <asm/proc-fns.h> + +#include "core.h" +#include "sysregs.h" + +void arch_reset(char mode, const char *cmd) +{ + if (mode == 'h') + hignbank_set_pwr_hard_reset(); + else + hignbank_set_pwr_soft_reset(); + + scu_power_mode(scu_base_addr, SCU_PM_POWEROFF); + cpu_do_idle(); +} + diff --git a/arch/arm/mach-imx/iomux-imx31.c b/arch/arm/mach-imx/iomux-imx31.c index cf8f8099ebd7..82bd4403b450 100644 --- a/arch/arm/mach-imx/iomux-imx31.c +++ b/arch/arm/mach-imx/iomux-imx31.c @@ -17,13 +17,12 @@ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, * MA 02110-1301, USA. */ - +#include <linux/gpio.h> #include <linux/module.h> #include <linux/spinlock.h> #include <linux/io.h> #include <linux/kernel.h> #include <mach/hardware.h> -#include <mach/gpio.h> #include <mach/iomux-mx3.h> /* diff --git a/arch/arm/mach-imx/mach-mx27ads.c b/arch/arm/mach-imx/mach-mx27ads.c index e75f39147845..74dd5731eb61 100644 --- a/arch/arm/mach-imx/mach-mx27ads.c +++ b/arch/arm/mach-imx/mach-mx27ads.c @@ -13,7 +13,7 @@ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. */ - +#include <linux/gpio.h> #include <linux/platform_device.h> #include <linux/mtd/mtd.h> #include <linux/mtd/map.h> @@ -27,7 +27,6 @@ #include <asm/mach/arch.h> #include <asm/mach/time.h> #include <asm/mach/map.h> -#include <mach/gpio.h> #include <mach/iomux-mx27.h> #include "devices-imx27.h" diff --git a/arch/arm/mach-integrator/include/mach/io.h b/arch/arm/mach-integrator/include/mach/io.h index f21bb5493dd9..37beed3fa3ed 100644 --- a/arch/arm/mach-integrator/include/mach/io.h +++ b/arch/arm/mach-integrator/include/mach/io.h @@ -20,8 +20,6 @@ #ifndef __ASM_ARM_ARCH_IO_H #define __ASM_ARM_ARCH_IO_H -#define IO_SPACE_LIMIT 0xffff - /* * WARNING: this has to mirror definitions in platform.h */ diff --git a/arch/arm/mach-ixp2000/core.c b/arch/arm/mach-ixp2000/core.c index 4068166c8993..59a512672bb9 100644 --- a/arch/arm/mach-ixp2000/core.c +++ b/arch/arm/mach-ixp2000/core.c @@ -13,7 +13,7 @@ * License version 2. This program is licensed "as is" without any * warranty of any kind, whether express or implied. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/spinlock.h> @@ -39,7 +39,7 @@ #include <asm/mach/time.h> #include <asm/mach/irq.h> -#include <mach/gpio.h> +#include <mach/gpio-ixp2000.h> static DEFINE_SPINLOCK(ixp2000_slowport_lock); static unsigned long ixp2000_slowport_irq_flags; diff --git a/arch/arm/mach-ixp2000/include/mach/gpio.h b/arch/arm/mach-ixp2000/include/mach/gpio-ixp2000.h index 4a88d2c33dac..af836c76c3f1 100644 --- a/arch/arm/mach-ixp2000/include/mach/gpio.h +++ b/arch/arm/mach-ixp2000/include/mach/gpio-ixp2000.h @@ -3,7 +3,7 @@ * * Copyright (C) 2002 Intel Corporation. * - * This program is free software, you can redistribute it and/or modify + * This program is free software, you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ @@ -11,7 +11,7 @@ /* * IXP2000 GPIO in/out, edge/level detection for IRQs: * IRQs are generated on Falling-edge, Rising-Edge, Level-low, Level-High - * or both Falling-edge and Rising-edge. + * or both Falling-edge and Rising-edge. * This must be called *before* the corresponding IRQ is registerd. * Use this instead of directly setting the GPIO registers. * GPIOs may also be used as GPIOs (e.g. for emulating i2c/smb) diff --git a/arch/arm/mach-ixp2000/ixdp2x00.c b/arch/arm/mach-ixp2000/ixdp2x00.c index 235638f800e5..634b6c852f68 100644 --- a/arch/arm/mach-ixp2000/ixdp2x00.c +++ b/arch/arm/mach-ixp2000/ixdp2x00.c @@ -14,6 +14,7 @@ * Free Software Foundation; either version 2 of the License, or (at your * option) any later version. */ +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/mm.h> @@ -40,8 +41,7 @@ #include <asm/mach/flash.h> #include <asm/mach/arch.h> -#include <mach/gpio.h> - +#include <mach/gpio-ixp2000.h> /************************************************************************* * IXDP2x00 IRQ Initialization diff --git a/arch/arm/mach-ixp4xx/dsmg600-setup.c b/arch/arm/mach-ixp4xx/dsmg600-setup.c index 71607a7ecc7e..8837fbca27ce 100644 --- a/arch/arm/mach-ixp4xx/dsmg600-setup.c +++ b/arch/arm/mach-ixp4xx/dsmg600-setup.c @@ -16,7 +16,7 @@ * Author: Rod Whitby <rod@whitby.id.au> * Maintainers: http://www.nslu2-linux.org/ */ - +#include <linux/gpio.h> #include <linux/irq.h> #include <linux/jiffies.h> #include <linux/timer.h> @@ -31,7 +31,6 @@ #include <asm/mach/arch.h> #include <asm/mach/flash.h> #include <asm/mach/time.h> -#include <asm/gpio.h> #define DSMG600_SDA_PIN 5 #define DSMG600_SCL_PIN 4 diff --git a/arch/arm/mach-ixp4xx/fsg-setup.c b/arch/arm/mach-ixp4xx/fsg-setup.c index a9540cd90375..2887c3578c17 100644 --- a/arch/arm/mach-ixp4xx/fsg-setup.c +++ b/arch/arm/mach-ixp4xx/fsg-setup.c @@ -14,7 +14,7 @@ * Maintainers: http://www.nslu2-linux.org/ * */ - +#include <linux/gpio.h> #include <linux/if_ether.h> #include <linux/irq.h> #include <linux/serial.h> @@ -27,7 +27,6 @@ #include <asm/mach-types.h> #include <asm/mach/arch.h> #include <asm/mach/flash.h> -#include <asm/gpio.h> #define FSG_SDA_PIN 12 #define FSG_SCL_PIN 13 diff --git a/arch/arm/mach-ixp4xx/include/mach/gpio.h b/arch/arm/mach-ixp4xx/include/mach/gpio.h index a5f87ded2f28..83d6b4ed60bb 100644 --- a/arch/arm/mach-ixp4xx/include/mach/gpio.h +++ b/arch/arm/mach-ixp4xx/include/mach/gpio.h @@ -28,6 +28,8 @@ #include <linux/kernel.h> #include <mach/hardware.h> +#define __ARM_GPIOLIB_COMPLEX + static inline int gpio_request(unsigned gpio, const char *label) { return 0; @@ -70,6 +72,7 @@ static inline void gpio_set_value(unsigned gpio, int value) #include <asm-generic/gpio.h> /* cansleep wrappers */ extern int gpio_to_irq(int gpio); +#define gpio_to_irq gpio_to_irq extern int irq_to_gpio(unsigned int irq); #endif diff --git a/arch/arm/mach-ixp4xx/include/mach/io.h b/arch/arm/mach-ixp4xx/include/mach/io.h index 57b5410c31f4..ffb9d6afb89f 100644 --- a/arch/arm/mach-ixp4xx/include/mach/io.h +++ b/arch/arm/mach-ixp4xx/include/mach/io.h @@ -17,8 +17,6 @@ #include <mach/hardware.h> -#define IO_SPACE_LIMIT 0x0000ffff - extern int (*ixp4xx_pci_read)(u32 addr, u32 cmd, u32* data); extern int ixp4xx_pci_write(u32 addr, u32 cmd, u32 data); diff --git a/arch/arm/mach-ixp4xx/nas100d-setup.c b/arch/arm/mach-ixp4xx/nas100d-setup.c index 9f4669260d4c..de716fa1aab6 100644 --- a/arch/arm/mach-ixp4xx/nas100d-setup.c +++ b/arch/arm/mach-ixp4xx/nas100d-setup.c @@ -17,7 +17,7 @@ * Maintainers: http://www.nslu2-linux.org/ * */ - +#include <linux/gpio.h> #include <linux/if_ether.h> #include <linux/irq.h> #include <linux/jiffies.h> @@ -32,7 +32,6 @@ #include <asm/mach-types.h> #include <asm/mach/arch.h> #include <asm/mach/flash.h> -#include <asm/gpio.h> #define NAS100D_SDA_PIN 5 #define NAS100D_SCL_PIN 6 diff --git a/arch/arm/mach-ixp4xx/nslu2-setup.c b/arch/arm/mach-ixp4xx/nslu2-setup.c index 3676fbf6ef9c..ac81ccb26bfe 100644 --- a/arch/arm/mach-ixp4xx/nslu2-setup.c +++ b/arch/arm/mach-ixp4xx/nslu2-setup.c @@ -16,7 +16,7 @@ * Maintainers: http://www.nslu2-linux.org/ * */ - +#include <linux/gpio.h> #include <linux/if_ether.h> #include <linux/irq.h> #include <linux/serial.h> @@ -30,7 +30,6 @@ #include <asm/mach/arch.h> #include <asm/mach/flash.h> #include <asm/mach/time.h> -#include <asm/gpio.h> #define NSLU2_SDA_PIN 7 #define NSLU2_SCL_PIN 6 diff --git a/arch/arm/mach-kirkwood/irq.c b/arch/arm/mach-kirkwood/irq.c index 05d193a25b25..c4c68e5b94f1 100644 --- a/arch/arm/mach-kirkwood/irq.c +++ b/arch/arm/mach-kirkwood/irq.c @@ -7,14 +7,13 @@ * License version 2. This program is licensed "as is" without any * warranty of any kind, whether express or implied. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/irq.h> #include <linux/io.h> #include <mach/bridge-regs.h> #include <plat/irq.h> -#include <asm/gpio.h> #include "common.h" static void gpio_irq_handler(unsigned int irq, struct irq_desc *desc) diff --git a/arch/arm/mach-kirkwood/mpp.c b/arch/arm/mach-kirkwood/mpp.c index b0a7d979a8ed..cc431fa22ccb 100644 --- a/arch/arm/mach-kirkwood/mpp.c +++ b/arch/arm/mach-kirkwood/mpp.c @@ -7,12 +7,11 @@ * License version 2. This program is licensed "as is" without any * warranty of any kind, whether express or implied. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/mbus.h> #include <linux/io.h> -#include <asm/gpio.h> #include <mach/hardware.h> #include <plat/mpp.h> #include "common.h" diff --git a/arch/arm/mach-ks8695/Makefile b/arch/arm/mach-ks8695/Makefile index 7e3e8160ed30..853efd9133c6 100644 --- a/arch/arm/mach-ks8695/Makefile +++ b/arch/arm/mach-ks8695/Makefile @@ -3,7 +3,7 @@ # Makefile for KS8695 architecture support # -obj-y := cpu.o irq.o time.o gpio.o devices.o +obj-y := cpu.o irq.o time.o devices.o obj-m := obj-n := obj- := diff --git a/arch/arm/mach-ks8695/board-acs5k.c b/arch/arm/mach-ks8695/board-acs5k.c index a5fcc7c7fe18..a91f99d265aa 100644 --- a/arch/arm/mach-ks8695/board-acs5k.c +++ b/arch/arm/mach-ks8695/board-acs5k.c @@ -10,7 +10,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/types.h> #include <linux/interrupt.h> @@ -34,7 +34,7 @@ #include <asm/mach/irq.h> #include <mach/devices.h> -#include <mach/gpio.h> +#include <mach/gpio-ks8695.h> #include "generic.h" diff --git a/arch/arm/mach-ks8695/board-dsm320.c b/arch/arm/mach-ks8695/board-dsm320.c index fb91a716a7db..d24bcef2e2dd 100644 --- a/arch/arm/mach-ks8695/board-dsm320.c +++ b/arch/arm/mach-ks8695/board-dsm320.c @@ -10,7 +10,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/types.h> #include <linux/interrupt.h> @@ -29,7 +29,7 @@ #include <asm/mach/irq.h> #include <mach/devices.h> -#include <mach/gpio.h> +#include <mach/gpio-ks8695.h> #include "generic.h" diff --git a/arch/arm/mach-ks8695/board-micrel.c b/arch/arm/mach-ks8695/board-micrel.c index 8f67a750b6c7..16c95657f8fd 100644 --- a/arch/arm/mach-ks8695/board-micrel.c +++ b/arch/arm/mach-ks8695/board-micrel.c @@ -5,7 +5,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/types.h> #include <linux/interrupt.h> @@ -18,7 +18,7 @@ #include <asm/mach/map.h> #include <asm/mach/irq.h> -#include <mach/gpio.h> +#include <mach/gpio-ks8695.h> #include <mach/devices.h> #include "generic.h" diff --git a/arch/arm/mach-ks8695/devices.c b/arch/arm/mach-ks8695/devices.c index b89fb6d46ccc..73bd63812878 100644 --- a/arch/arm/mach-ks8695/devices.c +++ b/arch/arm/mach-ks8695/devices.c @@ -20,6 +20,7 @@ #include <asm/mach/arch.h> #include <asm/mach/map.h> +#include <linux/gpio.h> #include <linux/platform_device.h> #include <mach/irqs.h> diff --git a/arch/arm/mach-ks8695/include/mach/gpio-ks8695.h b/arch/arm/mach-ks8695/include/mach/gpio-ks8695.h new file mode 100644 index 000000000000..6eb034d60325 --- /dev/null +++ b/arch/arm/mach-ks8695/include/mach/gpio-ks8695.h @@ -0,0 +1,39 @@ +/* + * Copyright (C) 2006 Andrew Victor + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __MACH_KS8659_GPIO_H +#define __MACH_KS8659_GPIO_H + +#include <linux/kernel.h> + +#define KS8695_GPIO_0 0 +#define KS8695_GPIO_1 1 +#define KS8695_GPIO_2 2 +#define KS8695_GPIO_3 3 +#define KS8695_GPIO_4 4 +#define KS8695_GPIO_5 5 +#define KS8695_GPIO_6 6 +#define KS8695_GPIO_7 7 +#define KS8695_GPIO_8 8 +#define KS8695_GPIO_9 9 +#define KS8695_GPIO_10 10 +#define KS8695_GPIO_11 11 +#define KS8695_GPIO_12 12 +#define KS8695_GPIO_13 13 +#define KS8695_GPIO_14 14 +#define KS8695_GPIO_15 15 + +/* + * Configure GPIO pin as external interrupt source. + */ +extern int ks8695_gpio_interrupt(unsigned int pin, unsigned int type); + +/* Register the GPIOs */ +extern void ks8695_register_gpios(void); + +#endif /* __MACH_KS8659_GPIO_H */ diff --git a/arch/arm/mach-ks8695/include/mach/gpio.h b/arch/arm/mach-ks8695/include/mach/gpio.h index 86312d476bc6..f5fda36e4512 100644 --- a/arch/arm/mach-ks8695/include/mach/gpio.h +++ b/arch/arm/mach-ks8695/include/mach/gpio.h @@ -11,47 +11,9 @@ #ifndef __ASM_ARCH_GPIO_H_ #define __ASM_ARCH_GPIO_H_ -#include <linux/kernel.h> - -#define KS8695_GPIO_0 0 -#define KS8695_GPIO_1 1 -#define KS8695_GPIO_2 2 -#define KS8695_GPIO_3 3 -#define KS8695_GPIO_4 4 -#define KS8695_GPIO_5 5 -#define KS8695_GPIO_6 6 -#define KS8695_GPIO_7 7 -#define KS8695_GPIO_8 8 -#define KS8695_GPIO_9 9 -#define KS8695_GPIO_10 10 -#define KS8695_GPIO_11 11 -#define KS8695_GPIO_12 12 -#define KS8695_GPIO_13 13 -#define KS8695_GPIO_14 14 -#define KS8695_GPIO_15 15 - -/* - * Configure GPIO pin as external interrupt source. - */ -extern int ks8695_gpio_interrupt(unsigned int pin, unsigned int type); - /* * Map IRQ number to GPIO line. */ extern int irq_to_gpio(unsigned int irq); -#include <asm-generic/gpio.h> - -/* If it turns out that we need to optimise GPIO access for the - * Micrel's GPIOs, then these can be changed to check their argument - * directly as static inlines. However for now it's probably not - * worthwhile. - */ -#define gpio_get_value __gpio_get_value -#define gpio_set_value __gpio_set_value -#define gpio_to_irq __gpio_to_irq - -/* Register the GPIOs */ -extern void ks8695_register_gpios(void); - #endif diff --git a/arch/arm/mach-ks8695/leds.c b/arch/arm/mach-ks8695/leds.c index 184ef74e4bee..d6f6502ac9b5 100644 --- a/arch/arm/mach-ks8695/leds.c +++ b/arch/arm/mach-ks8695/leds.c @@ -7,14 +7,14 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/module.h> #include <linux/init.h> +#include <linux/gpio.h> #include <asm/leds.h> #include <mach/devices.h> -#include <mach/gpio.h> static inline void ks8695_led_on(unsigned int led) diff --git a/arch/arm/mach-lpc32xx/Makefile b/arch/arm/mach-lpc32xx/Makefile index a5fc5d0eeaeb..f5db805ab958 100644 --- a/arch/arm/mach-lpc32xx/Makefile +++ b/arch/arm/mach-lpc32xx/Makefile @@ -3,6 +3,6 @@ # obj-y := timer.o irq.o common.o serial.o clock.o -obj-y += gpiolib.o pm.o suspend.o +obj-y += pm.o suspend.o obj-y += phy3250.o diff --git a/arch/arm/mach-lpc32xx/include/mach/gpio-lpc32xx.h b/arch/arm/mach-lpc32xx/include/mach/gpio-lpc32xx.h new file mode 100644 index 000000000000..1816e22a3479 --- /dev/null +++ b/arch/arm/mach-lpc32xx/include/mach/gpio-lpc32xx.h @@ -0,0 +1,50 @@ +/* + * Author: Kevin Wells <kevin.wells@nxp.com> + * + * Copyright (C) 2010 NXP Semiconductors + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef __MACH_GPIO_LPC32XX_H +#define __MACH_GPIO_LPC32XX_H + +/* + * Note! + * Muxed GP pins need to be setup to the GP state in the board level + * code prior to using this driver. + * GPI pins : 28xP3 group + * GPO pins : 24xP3 group + * GPIO pins: 8xP0 group, 24xP1 group, 13xP2 group, 6xP3 group + */ + +#define LPC32XX_GPIO_P0_MAX 8 +#define LPC32XX_GPIO_P1_MAX 24 +#define LPC32XX_GPIO_P2_MAX 13 +#define LPC32XX_GPIO_P3_MAX 6 +#define LPC32XX_GPI_P3_MAX 28 +#define LPC32XX_GPO_P3_MAX 24 + +#define LPC32XX_GPIO_P0_GRP 0 +#define LPC32XX_GPIO_P1_GRP (LPC32XX_GPIO_P0_GRP + LPC32XX_GPIO_P0_MAX) +#define LPC32XX_GPIO_P2_GRP (LPC32XX_GPIO_P1_GRP + LPC32XX_GPIO_P1_MAX) +#define LPC32XX_GPIO_P3_GRP (LPC32XX_GPIO_P2_GRP + LPC32XX_GPIO_P2_MAX) +#define LPC32XX_GPI_P3_GRP (LPC32XX_GPIO_P3_GRP + LPC32XX_GPIO_P3_MAX) +#define LPC32XX_GPO_P3_GRP (LPC32XX_GPI_P3_GRP + LPC32XX_GPI_P3_MAX) + +/* + * A specific GPIO can be selected with this macro + * ie, GPIO_05 can be selected with LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 5) + * See the LPC32x0 User's guide for GPIO group numbers + */ +#define LPC32XX_GPIO(x, y) ((x) + (y)) + +#endif /* __MACH_GPIO_LPC32XX_H */ diff --git a/arch/arm/mach-lpc32xx/include/mach/gpio.h b/arch/arm/mach-lpc32xx/include/mach/gpio.h index 67d03da1eee9..e69de29bb2d1 100644 --- a/arch/arm/mach-lpc32xx/include/mach/gpio.h +++ b/arch/arm/mach-lpc32xx/include/mach/gpio.h @@ -1,74 +0,0 @@ -/* - * arch/arm/mach-lpc32xx/include/mach/gpio.h - * - * Author: Kevin Wells <kevin.wells@nxp.com> - * - * Copyright (C) 2010 NXP Semiconductors - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - */ - -#ifndef __ASM_ARCH_GPIO_H -#define __ASM_ARCH_GPIO_H - -#include <asm-generic/gpio.h> - -/* - * Note! - * Muxed GP pins need to be setup to the GP state in the board level - * code prior to using this driver. - * GPI pins : 28xP3 group - * GPO pins : 24xP3 group - * GPIO pins: 8xP0 group, 24xP1 group, 13xP2 group, 6xP3 group - */ - -#define LPC32XX_GPIO_P0_MAX 8 -#define LPC32XX_GPIO_P1_MAX 24 -#define LPC32XX_GPIO_P2_MAX 13 -#define LPC32XX_GPIO_P3_MAX 6 -#define LPC32XX_GPI_P3_MAX 28 -#define LPC32XX_GPO_P3_MAX 24 - -#define LPC32XX_GPIO_P0_GRP 0 -#define LPC32XX_GPIO_P1_GRP (LPC32XX_GPIO_P0_GRP + LPC32XX_GPIO_P0_MAX) -#define LPC32XX_GPIO_P2_GRP (LPC32XX_GPIO_P1_GRP + LPC32XX_GPIO_P1_MAX) -#define LPC32XX_GPIO_P3_GRP (LPC32XX_GPIO_P2_GRP + LPC32XX_GPIO_P2_MAX) -#define LPC32XX_GPI_P3_GRP (LPC32XX_GPIO_P3_GRP + LPC32XX_GPIO_P3_MAX) -#define LPC32XX_GPO_P3_GRP (LPC32XX_GPI_P3_GRP + LPC32XX_GPI_P3_MAX) - -/* - * A specific GPIO can be selected with this macro - * ie, GPIO_05 can be selected with LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 5) - * See the LPC32x0 User's guide for GPIO group numbers - */ -#define LPC32XX_GPIO(x, y) ((x) + (y)) - -static inline int gpio_get_value(unsigned gpio) -{ - return __gpio_get_value(gpio); -} - -static inline void gpio_set_value(unsigned gpio, int value) -{ - __gpio_set_value(gpio, value); -} - -static inline int gpio_cansleep(unsigned gpio) -{ - return __gpio_cansleep(gpio); -} - -static inline int gpio_to_irq(unsigned gpio) -{ - return __gpio_to_irq(gpio); -} - -#endif diff --git a/arch/arm/mach-lpc32xx/phy3250.c b/arch/arm/mach-lpc32xx/phy3250.c index 9b621e14d16a..6d2f0d1b9373 100644 --- a/arch/arm/mach-lpc32xx/phy3250.c +++ b/arch/arm/mach-lpc32xx/phy3250.c @@ -37,6 +37,7 @@ #include <mach/hardware.h> #include <mach/platform.h> +#include <mach/gpio-lpc32xx.h> #include "common.h" /* diff --git a/arch/arm/mach-mmp/aspenite.c b/arch/arm/mach-mmp/aspenite.c index 06b5fa853c93..833c3a2784aa 100644 --- a/arch/arm/mach-mmp/aspenite.c +++ b/arch/arm/mach-mmp/aspenite.c @@ -8,7 +8,7 @@ * it under the terms of the GNU General Public License version 2 as * publishhed by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/init.h> #include <linux/kernel.h> #include <linux/platform_device.h> @@ -17,13 +17,13 @@ #include <linux/mtd/partitions.h> #include <linux/mtd/nand.h> #include <linux/interrupt.h> +#include <linux/gpio.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> #include <mach/addr-map.h> #include <mach/mfp-pxa168.h> #include <mach/pxa168.h> -#include <mach/gpio.h> #include <video/pxa168fb.h> #include <linux/input.h> #include <plat/pxa27x_keypad.h> diff --git a/arch/arm/mach-mmp/brownstone.c b/arch/arm/mach-mmp/brownstone.c index c79162a50f28..e411252e3d39 100644 --- a/arch/arm/mach-mmp/brownstone.c +++ b/arch/arm/mach-mmp/brownstone.c @@ -14,7 +14,6 @@ #include <linux/kernel.h> #include <linux/platform_device.h> #include <linux/io.h> -#include <linux/gpio.h> #include <linux/regulator/machine.h> #include <linux/regulator/max8649.h> #include <linux/regulator/fixed.h> diff --git a/arch/arm/mach-mmp/gplugd.c b/arch/arm/mach-mmp/gplugd.c index 98e25d9aaab6..32776f3739f1 100644 --- a/arch/arm/mach-mmp/gplugd.c +++ b/arch/arm/mach-mmp/gplugd.c @@ -9,11 +9,11 @@ */ #include <linux/init.h> +#include <linux/gpio.h> #include <asm/mach/arch.h> #include <asm/mach-types.h> -#include <mach/gpio.h> #include <mach/pxa168.h> #include <mach/mfp-pxa168.h> diff --git a/arch/arm/mach-mmp/include/mach/gpio-pxa.h b/arch/arm/mach-mmp/include/mach/gpio-pxa.h new file mode 100644 index 000000000000..c017a983eced --- /dev/null +++ b/arch/arm/mach-mmp/include/mach/gpio-pxa.h @@ -0,0 +1,30 @@ +#ifndef __ASM_MACH_GPIO_PXA_H +#define __ASM_MACH_GPIO_PXA_H + +#include <mach/addr-map.h> +#include <mach/irqs.h> + +#define GPIO_REGS_VIRT (APB_VIRT_BASE + 0x19000) + +#define BANK_OFF(n) (((n) < 3) ? (n) << 2 : 0x100 + (((n) - 3) << 2)) +#define GPIO_REG(x) (*((volatile u32 *)(GPIO_REGS_VIRT + (x)))) + +#define NR_BUILTIN_GPIO IRQ_GPIO_NUM + +#define gpio_to_bank(gpio) ((gpio) >> 5) + +/* NOTE: these macros are defined here to make optimization of + * gpio_{get,set}_value() to work when 'gpio' is a constant. + * Usage of these macros otherwise is no longer recommended, + * use generic GPIO API whenever possible. + */ +#define GPIO_bit(gpio) (1 << ((gpio) & 0x1f)) + +#define GPLR(x) GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x00) +#define GPDR(x) GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x0c) +#define GPSR(x) GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x18) +#define GPCR(x) GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x24) + +#include <plat/gpio-pxa.h> + +#endif /* __ASM_MACH_GPIO_PXA_H */ diff --git a/arch/arm/mach-mmp/include/mach/gpio.h b/arch/arm/mach-mmp/include/mach/gpio.h index 7bfb827f3fe3..681262359d1c 100644 --- a/arch/arm/mach-mmp/include/mach/gpio.h +++ b/arch/arm/mach-mmp/include/mach/gpio.h @@ -1,36 +1,13 @@ #ifndef __ASM_MACH_GPIO_H #define __ASM_MACH_GPIO_H -#include <mach/addr-map.h> -#include <mach/irqs.h> #include <asm-generic/gpio.h> -#define GPIO_REGS_VIRT (APB_VIRT_BASE + 0x19000) - -#define BANK_OFF(n) (((n) < 3) ? (n) << 2 : 0x100 + (((n) - 3) << 2)) -#define GPIO_REG(x) (*((volatile u32 *)(GPIO_REGS_VIRT + (x)))) - -#define NR_BUILTIN_GPIO IRQ_GPIO_NUM - -#define gpio_to_bank(gpio) ((gpio) >> 5) #define gpio_to_irq(gpio) (IRQ_GPIO_START + (gpio)) #define irq_to_gpio(irq) ((irq) - IRQ_GPIO_START) - #define __gpio_is_inverted(gpio) (0) #define __gpio_is_occupied(gpio) (0) -/* NOTE: these macros are defined here to make optimization of - * gpio_{get,set}_value() to work when 'gpio' is a constant. - * Usage of these macros otherwise is no longer recommended, - * use generic GPIO API whenever possible. - */ -#define GPIO_bit(gpio) (1 << ((gpio) & 0x1f)) - -#define GPLR(x) GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x00) -#define GPDR(x) GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x0c) -#define GPSR(x) GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x18) -#define GPCR(x) GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x24) - #include <plat/gpio.h> #endif /* __ASM_MACH_GPIO_H */ diff --git a/arch/arm/mach-mmp/jasper.c b/arch/arm/mach-mmp/jasper.c index 5d6421d63254..8bfac6612623 100644 --- a/arch/arm/mach-mmp/jasper.c +++ b/arch/arm/mach-mmp/jasper.c @@ -14,7 +14,6 @@ #include <linux/kernel.h> #include <linux/platform_device.h> #include <linux/io.h> -#include <linux/gpio.h> #include <linux/regulator/machine.h> #include <linux/regulator/max8649.h> #include <linux/mfd/max8925.h> diff --git a/arch/arm/mach-mmp/mmp2.c b/arch/arm/mach-mmp/mmp2.c index 079c18861d5c..65d8689e40c9 100644 --- a/arch/arm/mach-mmp/mmp2.c +++ b/arch/arm/mach-mmp/mmp2.c @@ -9,7 +9,6 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - #include <linux/module.h> #include <linux/kernel.h> #include <linux/init.h> @@ -25,7 +24,7 @@ #include <mach/irqs.h> #include <mach/dma.h> #include <mach/mfp.h> -#include <mach/gpio.h> +#include <mach/gpio-pxa.h> #include <mach/devices.h> #include <mach/mmp2.h> diff --git a/arch/arm/mach-mmp/pxa168.c b/arch/arm/mach-mmp/pxa168.c index 0156f535dae7..50c1763911ff 100644 --- a/arch/arm/mach-mmp/pxa168.c +++ b/arch/arm/mach-mmp/pxa168.c @@ -7,7 +7,6 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - #include <linux/module.h> #include <linux/kernel.h> #include <linux/init.h> @@ -21,7 +20,7 @@ #include <mach/regs-apbc.h> #include <mach/regs-apmu.h> #include <mach/irqs.h> -#include <mach/gpio.h> +#include <mach/gpio-pxa.h> #include <mach/dma.h> #include <mach/devices.h> #include <mach/mfp.h> diff --git a/arch/arm/mach-mmp/pxa910.c b/arch/arm/mach-mmp/pxa910.c index 1464607aa60d..4ebbfbba39fc 100644 --- a/arch/arm/mach-mmp/pxa910.c +++ b/arch/arm/mach-mmp/pxa910.c @@ -7,7 +7,6 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - #include <linux/module.h> #include <linux/kernel.h> #include <linux/init.h> @@ -20,7 +19,7 @@ #include <mach/regs-apmu.h> #include <mach/cputype.h> #include <mach/irqs.h> -#include <mach/gpio.h> +#include <mach/gpio-pxa.h> #include <mach/dma.h> #include <mach/mfp.h> #include <mach/devices.h> diff --git a/arch/arm/mach-mmp/tavorevb.c b/arch/arm/mach-mmp/tavorevb.c index c296b75c4453..eb5be879fd8c 100644 --- a/arch/arm/mach-mmp/tavorevb.c +++ b/arch/arm/mach-mmp/tavorevb.c @@ -7,18 +7,18 @@ * it under the terms of the GNU General Public License version 2 as * publishhed by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/init.h> #include <linux/kernel.h> #include <linux/platform_device.h> #include <linux/smc91x.h> +#include <linux/gpio.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> #include <mach/addr-map.h> #include <mach/mfp-pxa910.h> #include <mach/pxa910.h> -#include <mach/gpio.h> #include "common.h" diff --git a/arch/arm/mach-msm/board-msm7x27.c b/arch/arm/mach-msm/board-msm7x27.c index a80765533f13..6d84ee740df4 100644 --- a/arch/arm/mach-msm/board-msm7x27.c +++ b/arch/arm/mach-msm/board-msm7x27.c @@ -13,7 +13,7 @@ * GNU General Public License for more details. * */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -34,7 +34,6 @@ #include <mach/vreg.h> #include <mach/mpp.h> -#include <mach/gpio.h> #include <mach/board.h> #include <mach/msm_iomap.h> diff --git a/arch/arm/mach-msm/board-msm7x30.c b/arch/arm/mach-msm/board-msm7x30.c index bb72ea0383b7..71de5062c71e 100644 --- a/arch/arm/mach-msm/board-msm7x30.c +++ b/arch/arm/mach-msm/board-msm7x30.c @@ -14,7 +14,7 @@ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA * 02110-1301, USA. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/irq.h> #include <linux/gpio.h> @@ -31,7 +31,6 @@ #include <asm/memory.h> #include <asm/setup.h> -#include <mach/gpio.h> #include <mach/board.h> #include <mach/msm_iomap.h> #include <mach/dma.h> diff --git a/arch/arm/mach-msm/board-qsd8x50.c b/arch/arm/mach-msm/board-qsd8x50.c index 51109b1f4342..7e8909c978c3 100644 --- a/arch/arm/mach-msm/board-qsd8x50.c +++ b/arch/arm/mach-msm/board-qsd8x50.c @@ -14,7 +14,7 @@ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA * 02110-1301, USA. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/irq.h> #include <linux/gpio.h> @@ -32,7 +32,6 @@ #include <mach/board.h> #include <mach/irqs.h> #include <mach/sirc.h> -#include <mach/gpio.h> #include <mach/vreg.h> #include <mach/mmc.h> diff --git a/arch/arm/mach-msm/board-sapphire.c b/arch/arm/mach-msm/board-sapphire.c index dc0bcb5a6b9a..afa9293d5800 100644 --- a/arch/arm/mach-msm/board-sapphire.c +++ b/arch/arm/mach-msm/board-sapphire.c @@ -11,7 +11,7 @@ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -22,7 +22,6 @@ #include <linux/delay.h> -#include <asm/gpio.h> #include <mach/hardware.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> diff --git a/arch/arm/mach-msm/board-trout-mmc.c b/arch/arm/mach-msm/board-trout-mmc.c index f7a9724788b0..8650342b7493 100644 --- a/arch/arm/mach-msm/board-trout-mmc.c +++ b/arch/arm/mach-msm/board-trout-mmc.c @@ -1,7 +1,7 @@ /* linux/arch/arm/mach-msm/board-trout-mmc.c ** Author: Brian Swetland <swetland@google.com> */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -11,7 +11,6 @@ #include <linux/err.h> #include <linux/debugfs.h> -#include <asm/gpio.h> #include <asm/io.h> #include <mach/vreg.h> diff --git a/arch/arm/mach-msm/board-trout-panel.c b/arch/arm/mach-msm/board-trout-panel.c index 729bb49a44ca..25105c1027fe 100644 --- a/arch/arm/mach-msm/board-trout-panel.c +++ b/arch/arm/mach-msm/board-trout-panel.c @@ -1,7 +1,7 @@ /* linux/arch/arm/mach-msm/board-trout-mddi.c ** Author: Brian Swetland <swetland@google.com> */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -11,7 +11,6 @@ #include <linux/err.h> #include <asm/io.h> -#include <asm/gpio.h> #include <asm/mach-types.h> #include <mach/msm_fb.h> diff --git a/arch/arm/mach-msm/include/mach/gpio.h b/arch/arm/mach-msm/include/mach/gpio.h index 36ad50d3bfaa..40a8c178f10d 100644 --- a/arch/arm/mach-msm/include/mach/gpio.h +++ b/arch/arm/mach-msm/include/mach/gpio.h @@ -1,26 +1 @@ -/* - * Copyright (C) 2007 Google, Inc. - * Copyright (c) 2009-2010, Code Aurora Forum. All rights reserved. - * Author: Mike Lockwood <lockwood@android.com> - * - * This software is licensed under the terms of the GNU General Public - * License version 2, as published by the Free Software Foundation, and - * may be copied, distributed, and modified under those terms. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - */ -#ifndef __ASM_ARCH_MSM_GPIO_H -#define __ASM_ARCH_MSM_GPIO_H - -#include <asm-generic/gpio.h> - -#define gpio_get_value __gpio_get_value -#define gpio_set_value __gpio_set_value -#define gpio_cansleep __gpio_cansleep -#define gpio_to_irq __gpio_to_irq - -#endif /* __ASM_ARCH_MSM_GPIO_H */ +/* empty */ diff --git a/arch/arm/mach-mv78xx0/irq.c b/arch/arm/mach-mv78xx0/irq.c index 3e24431bb5ea..e421b701663b 100644 --- a/arch/arm/mach-mv78xx0/irq.c +++ b/arch/arm/mach-mv78xx0/irq.c @@ -7,12 +7,11 @@ * License version 2. This program is licensed "as is" without any * warranty of any kind, whether express or implied. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/pci.h> #include <linux/irq.h> -#include <asm/gpio.h> #include <mach/bridge-regs.h> #include <plat/irq.h> #include "common.h" diff --git a/arch/arm/mach-mv78xx0/mpp.c b/arch/arm/mach-mv78xx0/mpp.c index 59b7686b9209..cf4e494d44bf 100644 --- a/arch/arm/mach-mv78xx0/mpp.c +++ b/arch/arm/mach-mv78xx0/mpp.c @@ -7,13 +7,12 @@ * License version 2. This program is licensed "as is" without any * warranty of any kind, whether express or implied. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/mbus.h> #include <linux/io.h> #include <plat/mpp.h> -#include <asm/gpio.h> #include <mach/hardware.h> #include "common.h" #include "mpp.h" diff --git a/arch/arm/mach-mxs/include/mach/gpio.h b/arch/arm/mach-mxs/include/mach/gpio.h index 56025aa0a639..40a8c178f10d 100644 --- a/arch/arm/mach-mxs/include/mach/gpio.h +++ b/arch/arm/mach-mxs/include/mach/gpio.h @@ -1,31 +1 @@ -/* - * Copyright 2007 Freescale Semiconductor, Inc. All Rights Reserved. - * Copyright 2008 Juergen Beisert, kernel@pengutronix.de - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version 2 - * of the License, or (at your option) any later version. - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, - * MA 02110-1301, USA. - */ - -#ifndef __MACH_MXS_GPIO_H__ -#define __MACH_MXS_GPIO_H__ - -#include <asm-generic/gpio.h> - -/* use gpiolib dispatchers */ -#define gpio_get_value __gpio_get_value -#define gpio_set_value __gpio_set_value -#define gpio_cansleep __gpio_cansleep -#define gpio_to_irq __gpio_to_irq - -#endif /* __MACH_MXS_GPIO_H__ */ +/* empty */ diff --git a/arch/arm/mach-nomadik/board-nhk8815.c b/arch/arm/mach-nomadik/board-nhk8815.c index 398a75f62bee..0cbb74c96ef7 100644 --- a/arch/arm/mach-nomadik/board-nhk8815.c +++ b/arch/arm/mach-nomadik/board-nhk8815.c @@ -27,6 +27,7 @@ #include <asm/mach/irq.h> #include <asm/mach/flash.h> +#include <plat/gpio-nomadik.h> #include <plat/mtu.h> #include <mach/setup.h> diff --git a/arch/arm/mach-nomadik/cpu-8815.c b/arch/arm/mach-nomadik/cpu-8815.c index ac58e3b03b1a..dc67717db6f0 100644 --- a/arch/arm/mach-nomadik/cpu-8815.c +++ b/arch/arm/mach-nomadik/cpu-8815.c @@ -21,8 +21,8 @@ #include <linux/device.h> #include <linux/amba/bus.h> #include <linux/platform_device.h> -#include <linux/gpio.h> +#include <plat/gpio-nomadik.h> #include <mach/hardware.h> #include <mach/irqs.h> #include <asm/mach/map.h> diff --git a/arch/arm/mach-nomadik/i2c-8815nhk.c b/arch/arm/mach-nomadik/i2c-8815nhk.c index abfe25a08d6b..0fc2f6f1cc97 100644 --- a/arch/arm/mach-nomadik/i2c-8815nhk.c +++ b/arch/arm/mach-nomadik/i2c-8815nhk.c @@ -3,8 +3,8 @@ #include <linux/i2c.h> #include <linux/i2c-algo-bit.h> #include <linux/i2c-gpio.h> -#include <linux/gpio.h> #include <linux/platform_device.h> +#include <plat/gpio-nomadik.h> /* * There are two busses in the 8815NHK. diff --git a/arch/arm/mach-nomadik/include/mach/gpio.h b/arch/arm/mach-nomadik/include/mach/gpio.h index 7a81a0420343..efdde0ae0a4f 100644 --- a/arch/arm/mach-nomadik/include/mach/gpio.h +++ b/arch/arm/mach-nomadik/include/mach/gpio.h @@ -1,6 +1,4 @@ #ifndef __ASM_ARCH_GPIO_H #define __ASM_ARCH_GPIO_H -#include <plat/gpio.h> - #endif /* __ASM_ARCH_GPIO_H */ diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c index eb36b25450a0..4ea60e2038ea 100644 --- a/arch/arm/mach-omap1/board-ams-delta.c +++ b/arch/arm/mach-omap1/board-ams-delta.c @@ -11,7 +11,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/input.h> @@ -30,7 +30,6 @@ #include <plat/io.h> #include <plat/board-ams-delta.h> -#include <mach/gpio.h> #include <plat/keypad.h> #include <plat/mux.h> #include <plat/usb.h> diff --git a/arch/arm/mach-omap1/board-fsample.c b/arch/arm/mach-omap1/board-fsample.c index 999789c4811d..31e089b6f03f 100644 --- a/arch/arm/mach-omap1/board-fsample.c +++ b/arch/arm/mach-omap1/board-fsample.c @@ -10,7 +10,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -28,7 +28,6 @@ #include <asm/mach/map.h> #include <plat/tc.h> -#include <mach/gpio.h> #include <plat/mux.h> #include <plat/flash.h> #include <plat/fpga.h> diff --git a/arch/arm/mach-omap1/board-generic.c b/arch/arm/mach-omap1/board-generic.c index 23cc9e4ad50d..05c6e9d858f3 100644 --- a/arch/arm/mach-omap1/board-generic.c +++ b/arch/arm/mach-omap1/board-generic.c @@ -12,7 +12,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -22,7 +22,6 @@ #include <asm/mach/arch.h> #include <asm/mach/map.h> -#include <mach/gpio.h> #include <plat/mux.h> #include <plat/usb.h> #include <plat/board.h> diff --git a/arch/arm/mach-omap1/board-h2-mmc.c b/arch/arm/mach-omap1/board-h2-mmc.c index f2fc43d8382b..da0e37d40823 100644 --- a/arch/arm/mach-omap1/board-h2-mmc.c +++ b/arch/arm/mach-omap1/board-h2-mmc.c @@ -11,13 +11,12 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/platform_device.h> #include <linux/i2c/tps65010.h> #include <plat/mmc.h> -#include <mach/gpio.h> #include "board-h2.h" diff --git a/arch/arm/mach-omap1/board-h2.c b/arch/arm/mach-omap1/board-h2.c index 6c70c28d055c..c2e279173d42 100644 --- a/arch/arm/mach-omap1/board-h2.c +++ b/arch/arm/mach-omap1/board-h2.c @@ -18,7 +18,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/platform_device.h> #include <linux/delay.h> @@ -32,7 +32,6 @@ #include <linux/smc91x.h> #include <mach/hardware.h> -#include <asm/gpio.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> diff --git a/arch/arm/mach-omap1/board-h3-mmc.c b/arch/arm/mach-omap1/board-h3-mmc.c index 2098525e7cc5..f8242aa9b763 100644 --- a/arch/arm/mach-omap1/board-h3-mmc.c +++ b/arch/arm/mach-omap1/board-h3-mmc.c @@ -11,13 +11,12 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/platform_device.h> #include <linux/i2c/tps65010.h> #include <plat/mmc.h> -#include <mach/gpio.h> #include "board-h3.h" diff --git a/arch/arm/mach-omap1/board-h3.c b/arch/arm/mach-omap1/board-h3.c index 8e2b64a46929..8f5b6af7ed59 100644 --- a/arch/arm/mach-omap1/board-h3.c +++ b/arch/arm/mach-omap1/board-h3.c @@ -13,7 +13,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/types.h> #include <linux/init.h> #include <linux/major.h> @@ -34,7 +34,6 @@ #include <asm/setup.h> #include <asm/page.h> #include <mach/hardware.h> -#include <asm/gpio.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> diff --git a/arch/arm/mach-omap1/board-htcherald.c b/arch/arm/mach-omap1/board-htcherald.c index e81ead1c89ea..fcd1a3c31896 100644 --- a/arch/arm/mach-omap1/board-htcherald.c +++ b/arch/arm/mach-omap1/board-htcherald.c @@ -23,7 +23,6 @@ * 02110-1301, USA. * */ - #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> diff --git a/arch/arm/mach-omap1/board-innovator.c b/arch/arm/mach-omap1/board-innovator.c index 8b034594fbc7..c2234caf8a7a 100644 --- a/arch/arm/mach-omap1/board-innovator.c +++ b/arch/arm/mach-omap1/board-innovator.c @@ -15,7 +15,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -34,7 +34,6 @@ #include <plat/mux.h> #include <plat/flash.h> #include <plat/fpga.h> -#include <mach/gpio.h> #include <plat/tc.h> #include <plat/usb.h> #include <plat/keypad.h> diff --git a/arch/arm/mach-omap1/board-nokia770.c b/arch/arm/mach-omap1/board-nokia770.c index 6825635ac681..02789c5d3703 100644 --- a/arch/arm/mach-omap1/board-nokia770.c +++ b/arch/arm/mach-omap1/board-nokia770.c @@ -7,7 +7,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/mutex.h> @@ -26,7 +26,6 @@ #include <asm/mach/arch.h> #include <asm/mach/map.h> -#include <mach/gpio.h> #include <plat/mux.h> #include <plat/usb.h> #include <plat/board.h> diff --git a/arch/arm/mach-omap1/board-osk.c b/arch/arm/mach-omap1/board-osk.c index 44b8e9362bf4..e4dca1deebb4 100644 --- a/arch/arm/mach-omap1/board-osk.c +++ b/arch/arm/mach-omap1/board-osk.c @@ -25,7 +25,7 @@ * with this program; if not, write to the Free Software Foundation, Inc., * 675 Mass Ave, Cambridge, MA 02139, USA. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -42,7 +42,6 @@ #include <linux/i2c/tps65010.h> #include <mach/hardware.h> -#include <asm/gpio.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> diff --git a/arch/arm/mach-omap1/board-palmte.c b/arch/arm/mach-omap1/board-palmte.c index 3d8cd90b1dbb..50c4e398bcc8 100644 --- a/arch/arm/mach-omap1/board-palmte.c +++ b/arch/arm/mach-omap1/board-palmte.c @@ -16,7 +16,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/input.h> @@ -33,7 +33,6 @@ #include <asm/mach/arch.h> #include <asm/mach/map.h> -#include <mach/gpio.h> #include <plat/flash.h> #include <plat/mux.h> #include <plat/usb.h> diff --git a/arch/arm/mach-omap1/board-palmtt.c b/arch/arm/mach-omap1/board-palmtt.c index d0eefe81cd1b..273771cb1b61 100644 --- a/arch/arm/mach-omap1/board-palmtt.c +++ b/arch/arm/mach-omap1/board-palmtt.c @@ -12,6 +12,7 @@ */ #include <linux/delay.h> +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -30,7 +31,6 @@ #include <asm/mach/map.h> #include <plat/led.h> -#include <mach/gpio.h> #include <plat/flash.h> #include <plat/mux.h> #include <plat/usb.h> diff --git a/arch/arm/mach-omap1/board-palmz71.c b/arch/arm/mach-omap1/board-palmz71.c index 98e79bc09213..de36ade38ef7 100644 --- a/arch/arm/mach-omap1/board-palmz71.c +++ b/arch/arm/mach-omap1/board-palmz71.c @@ -15,6 +15,7 @@ */ #include <linux/delay.h> +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -32,7 +33,6 @@ #include <asm/mach/arch.h> #include <asm/mach/map.h> -#include <mach/gpio.h> #include <plat/flash.h> #include <plat/mux.h> #include <plat/usb.h> diff --git a/arch/arm/mach-omap1/board-perseus2.c b/arch/arm/mach-omap1/board-perseus2.c index ad3a1567604e..04b1befaced6 100644 --- a/arch/arm/mach-omap1/board-perseus2.c +++ b/arch/arm/mach-omap1/board-perseus2.c @@ -10,7 +10,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -28,7 +28,6 @@ #include <asm/mach/map.h> #include <plat/tc.h> -#include <mach/gpio.h> #include <plat/mux.h> #include <plat/fpga.h> #include <plat/flash.h> diff --git a/arch/arm/mach-omap1/board-sx1-mmc.c b/arch/arm/mach-omap1/board-sx1-mmc.c index e8ddd86e3fda..b59f78850e69 100644 --- a/arch/arm/mach-omap1/board-sx1-mmc.c +++ b/arch/arm/mach-omap1/board-sx1-mmc.c @@ -12,11 +12,11 @@ * published by the Free Software Foundation. */ +#include <linux/gpio.h> #include <linux/platform_device.h> #include <mach/hardware.h> #include <plat/mmc.h> -#include <mach/gpio.h> #include <plat/board-sx1.h> #if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE) diff --git a/arch/arm/mach-omap1/board-sx1.c b/arch/arm/mach-omap1/board-sx1.c index 602b55c39d3d..2bea941741d5 100644 --- a/arch/arm/mach-omap1/board-sx1.c +++ b/arch/arm/mach-omap1/board-sx1.c @@ -14,7 +14,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/input.h> @@ -32,7 +32,6 @@ #include <asm/mach/arch.h> #include <asm/mach/map.h> -#include <mach/gpio.h> #include <plat/flash.h> #include <plat/mux.h> #include <plat/dma.h> diff --git a/arch/arm/mach-omap1/board-voiceblue.c b/arch/arm/mach-omap1/board-voiceblue.c index 80165154617a..940faed82be2 100644 --- a/arch/arm/mach-omap1/board-voiceblue.c +++ b/arch/arm/mach-omap1/board-voiceblue.c @@ -13,6 +13,7 @@ */ #include <linux/delay.h> +#include <linux/gpio.h> #include <linux/platform_device.h> #include <linux/interrupt.h> #include <linux/irq.h> @@ -33,7 +34,6 @@ #include <plat/board-voiceblue.h> #include <plat/common.h> -#include <mach/gpio.h> #include <plat/flash.h> #include <plat/mux.h> #include <plat/tc.h> diff --git a/arch/arm/mach-omap1/devices.c b/arch/arm/mach-omap1/devices.c index 36f26c3fa25e..7c50ecf68123 100644 --- a/arch/arm/mach-omap1/devices.c +++ b/arch/arm/mach-omap1/devices.c @@ -10,6 +10,7 @@ */ #include <linux/dma-mapping.h> +#include <linux/gpio.h> #include <linux/module.h> #include <linux/kernel.h> #include <linux/init.h> @@ -24,7 +25,6 @@ #include <plat/tc.h> #include <plat/board.h> #include <plat/mux.h> -#include <mach/gpio.h> #include <plat/mmc.h> #include <plat/omap7xx.h> #include <plat/mcbsp.h> diff --git a/arch/arm/mach-omap1/fpga.c b/arch/arm/mach-omap1/fpga.c index cddbf8b089ce..0a17a1a7e00d 100644 --- a/arch/arm/mach-omap1/fpga.c +++ b/arch/arm/mach-omap1/fpga.c @@ -17,6 +17,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/kernel.h> #include <linux/device.h> @@ -28,7 +29,6 @@ #include <asm/mach/irq.h> #include <plat/fpga.h> -#include <mach/gpio.h> static void fpga_mask_irq(struct irq_data *d) { diff --git a/arch/arm/mach-omap1/irq.c b/arch/arm/mach-omap1/irq.c index e2b9c901ab67..e5b104b7fce6 100644 --- a/arch/arm/mach-omap1/irq.c +++ b/arch/arm/mach-omap1/irq.c @@ -35,7 +35,7 @@ * with this program; if not, write to the Free Software Foundation, Inc., * 675 Mass Ave, Cambridge, MA 02139, USA. */ - +#include <linux/gpio.h> #include <linux/init.h> #include <linux/module.h> #include <linux/sched.h> @@ -45,7 +45,6 @@ #include <mach/hardware.h> #include <asm/irq.h> #include <asm/mach/irq.h> -#include <mach/gpio.h> #include <plat/cpu.h> #define IRQ_BANK(irq) ((irq) >> 5) diff --git a/arch/arm/mach-omap1/leds-h2p2-debug.c b/arch/arm/mach-omap1/leds-h2p2-debug.c index b4f9be52e1e8..4b818eb9f911 100644 --- a/arch/arm/mach-omap1/leds-h2p2-debug.c +++ b/arch/arm/mach-omap1/leds-h2p2-debug.c @@ -9,6 +9,7 @@ * The "surfer" expansion board and H2 sample board also have two-color * green+red LEDs (in parallel), used here for timer and idle indicators. */ +#include <linux/gpio.h> #include <linux/init.h> #include <linux/kernel_stat.h> #include <linux/sched.h> @@ -20,7 +21,6 @@ #include <asm/mach-types.h> #include <plat/fpga.h> -#include <mach/gpio.h> #include "leds.h" diff --git a/arch/arm/mach-omap1/leds-osk.c b/arch/arm/mach-omap1/leds-osk.c index 499d7ad8697d..da09f4364979 100644 --- a/arch/arm/mach-omap1/leds-osk.c +++ b/arch/arm/mach-omap1/leds-osk.c @@ -3,14 +3,13 @@ * * LED driver for OSK with optional Mistral QVGA board */ +#include <linux/gpio.h> #include <linux/init.h> #include <mach/hardware.h> #include <asm/leds.h> #include <asm/system.h> -#include <mach/gpio.h> - #include "leds.h" diff --git a/arch/arm/mach-omap1/leds.c b/arch/arm/mach-omap1/leds.c index 22eb11dde9e7..ae6dd93b8ddc 100644 --- a/arch/arm/mach-omap1/leds.c +++ b/arch/arm/mach-omap1/leds.c @@ -3,13 +3,13 @@ * * OMAP LEDs dispatcher */ +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <asm/leds.h> #include <asm/mach-types.h> -#include <mach/gpio.h> #include <plat/mux.h> #include "leds.h" diff --git a/arch/arm/mach-omap1/serial.c b/arch/arm/mach-omap1/serial.c index 550ca9d9991d..93ae8f29727e 100644 --- a/arch/arm/mach-omap1/serial.c +++ b/arch/arm/mach-omap1/serial.c @@ -7,7 +7,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/module.h> #include <linux/kernel.h> #include <linux/init.h> @@ -24,7 +24,6 @@ #include <plat/board.h> #include <plat/mux.h> -#include <mach/gpio.h> #include <plat/fpga.h> #include "pm.h" diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c index 0c427976d62f..67f0a122e18b 100644 --- a/arch/arm/mach-omap2/board-generic.c +++ b/arch/arm/mach-omap2/board-generic.c @@ -11,7 +11,10 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/device.h> #include <linux/io.h> #include <linux/of_platform.h> #include <linux/irqdomain.h> @@ -20,6 +23,7 @@ #include <mach/hardware.h> #include <asm/mach/arch.h> +#include <plat/usb.h> #include <plat/board.h> #include <plat/common.h> #include <mach/omap4-common.h> diff --git a/arch/arm/mach-omap2/board-h4.c b/arch/arm/mach-omap2/board-h4.c index fe75c195f69f..a65effe7e8d5 100644 --- a/arch/arm/mach-omap2/board-h4.c +++ b/arch/arm/mach-omap2/board-h4.c @@ -10,7 +10,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -31,7 +31,6 @@ #include <asm/mach/arch.h> #include <asm/mach/map.h> -#include <mach/gpio.h> #include <plat/usb.h> #include <plat/board.h> #include <plat/common.h> diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-ldp.c index 0fa28be2cfda..57979175cff3 100644 --- a/arch/arm/mach-omap2/board-ldp.c +++ b/arch/arm/mach-omap2/board-ldp.c @@ -10,7 +10,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -34,7 +34,6 @@ #include <asm/mach/map.h> #include <plat/mcspi.h> -#include <mach/gpio.h> #include <plat/board.h> #include <plat/common.h> #include <plat/gpmc.h> diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c index 0f8e0eb18166..37b4ef8b07e8 100644 --- a/arch/arm/mach-omap2/devices.c +++ b/arch/arm/mach-omap2/devices.c @@ -8,7 +8,7 @@ * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -27,7 +27,6 @@ #include <plat/tc.h> #include <plat/board.h> #include <plat/mcbsp.h> -#include <mach/gpio.h> #include <plat/mmc.h> #include <plat/dma.h> #include <plat/omap_hwmod.h> diff --git a/arch/arm/mach-orion5x/db88f5281-setup.c b/arch/arm/mach-orion5x/db88f5281-setup.c index 88432aba972c..4b79a80d5e1f 100644 --- a/arch/arm/mach-orion5x/db88f5281-setup.c +++ b/arch/arm/mach-orion5x/db88f5281-setup.c @@ -9,7 +9,7 @@ * License version 2. This program is licensed "as is" without any * warranty of any kind, whether express or implied. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -21,7 +21,6 @@ #include <linux/mv643xx_eth.h> #include <linux/i2c.h> #include <asm/mach-types.h> -#include <asm/gpio.h> #include <asm/mach/arch.h> #include <asm/mach/pci.h> #include <mach/orion5x.h> diff --git a/arch/arm/mach-orion5x/dns323-setup.c b/arch/arm/mach-orion5x/dns323-setup.c index 9e5c1663fc4f..343f60e9639f 100644 --- a/arch/arm/mach-orion5x/dns323-setup.c +++ b/arch/arm/mach-orion5x/dns323-setup.c @@ -13,7 +13,7 @@ * License, or (at your option) any later version. * */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/delay.h> @@ -30,7 +30,6 @@ #include <linux/phy.h> #include <linux/marvell_phy.h> #include <asm/mach-types.h> -#include <asm/gpio.h> #include <asm/mach/arch.h> #include <asm/mach/pci.h> #include <mach/orion5x.h> diff --git a/arch/arm/mach-orion5x/irq.c b/arch/arm/mach-orion5x/irq.c index 43cf8bc9767b..b1b45fff776e 100644 --- a/arch/arm/mach-orion5x/irq.c +++ b/arch/arm/mach-orion5x/irq.c @@ -9,12 +9,11 @@ * License version 2. This program is licensed "as is" without any * warranty of any kind, whether express or implied. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/irq.h> #include <linux/io.h> -#include <asm/gpio.h> #include <mach/bridge-regs.h> #include <plat/irq.h> #include "common.h" diff --git a/arch/arm/mach-orion5x/kurobox_pro-setup.c b/arch/arm/mach-orion5x/kurobox_pro-setup.c index 9115511dc035..d3cd3f63258a 100644 --- a/arch/arm/mach-orion5x/kurobox_pro-setup.c +++ b/arch/arm/mach-orion5x/kurobox_pro-setup.c @@ -7,7 +7,7 @@ * License version 2. This program is licensed "as is" without any * warranty of any kind, whether express or implied. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -21,7 +21,6 @@ #include <linux/serial_reg.h> #include <linux/ata_platform.h> #include <asm/mach-types.h> -#include <asm/gpio.h> #include <asm/mach/arch.h> #include <asm/mach/pci.h> #include <mach/orion5x.h> diff --git a/arch/arm/mach-orion5x/mv2120-setup.c b/arch/arm/mach-orion5x/mv2120-setup.c index b3356ada64b9..201ae3676289 100644 --- a/arch/arm/mach-orion5x/mv2120-setup.c +++ b/arch/arm/mach-orion5x/mv2120-setup.c @@ -7,7 +7,7 @@ * published by the Free Software Foundation; either version 2 of the * License, or (at your option) any later version. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -20,7 +20,6 @@ #include <linux/i2c.h> #include <linux/ata_platform.h> #include <asm/mach-types.h> -#include <asm/gpio.h> #include <asm/mach/arch.h> #include <mach/orion5x.h> #include "common.h" diff --git a/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c b/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c index 8c876664f494..ebd6767d8e88 100644 --- a/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c +++ b/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c @@ -7,7 +7,7 @@ * License version 2. This program is licensed "as is" without any * warranty of any kind, whether express or implied. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -18,7 +18,6 @@ #include <linux/ethtool.h> #include <net/dsa.h> #include <asm/mach-types.h> -#include <asm/gpio.h> #include <asm/leds.h> #include <asm/mach/arch.h> #include <asm/mach/pci.h> diff --git a/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c b/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c index 994644f59d8d..05db2d336b08 100644 --- a/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c +++ b/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c @@ -7,7 +7,7 @@ * License version 2. This program is licensed "as is" without any * warranty of any kind, whether express or implied. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -19,7 +19,6 @@ #include <linux/i2c.h> #include <net/dsa.h> #include <asm/mach-types.h> -#include <asm/gpio.h> #include <asm/leds.h> #include <asm/mach/arch.h> #include <asm/mach/pci.h> diff --git a/arch/arm/mach-orion5x/rd88f5182-setup.c b/arch/arm/mach-orion5x/rd88f5182-setup.c index 1903d25ecae9..e47fa0578ae3 100644 --- a/arch/arm/mach-orion5x/rd88f5182-setup.c +++ b/arch/arm/mach-orion5x/rd88f5182-setup.c @@ -9,7 +9,7 @@ * License version 2. This program is licensed "as is" without any * warranty of any kind, whether express or implied. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -20,7 +20,6 @@ #include <linux/ata_platform.h> #include <linux/i2c.h> #include <asm/mach-types.h> -#include <asm/gpio.h> #include <asm/leds.h> #include <asm/mach/arch.h> #include <asm/mach/pci.h> diff --git a/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c b/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c index e06fdae77f0a..64317251ec00 100644 --- a/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c +++ b/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c @@ -7,7 +7,7 @@ * License version 2. This program is licensed "as is" without any * warranty of any kind, whether express or implied. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -21,7 +21,6 @@ #include <linux/ethtool.h> #include <net/dsa.h> #include <asm/mach-types.h> -#include <asm/gpio.h> #include <asm/leds.h> #include <asm/mach/arch.h> #include <asm/mach/pci.h> diff --git a/arch/arm/mach-orion5x/terastation_pro2-setup.c b/arch/arm/mach-orion5x/terastation_pro2-setup.c index 306183273eb9..29f1526f7b70 100644 --- a/arch/arm/mach-orion5x/terastation_pro2-setup.c +++ b/arch/arm/mach-orion5x/terastation_pro2-setup.c @@ -8,7 +8,7 @@ * as published by the Free Software Foundation; either version * 2 of the License, or (at your option) any later version. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -20,7 +20,6 @@ #include <linux/i2c.h> #include <linux/serial_reg.h> #include <asm/mach-types.h> -#include <asm/gpio.h> #include <asm/mach/arch.h> #include <asm/mach/pci.h> #include <mach/orion5x.h> diff --git a/arch/arm/mach-orion5x/ts209-setup.c b/arch/arm/mach-orion5x/ts209-setup.c index 3dbcd5ed77ef..31e51f9b4b64 100644 --- a/arch/arm/mach-orion5x/ts209-setup.c +++ b/arch/arm/mach-orion5x/ts209-setup.c @@ -8,7 +8,7 @@ * as published by the Free Software Foundation; either version * 2 of the License, or (at your option) any later version. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -23,7 +23,6 @@ #include <linux/serial_reg.h> #include <linux/ata_platform.h> #include <asm/mach-types.h> -#include <asm/gpio.h> #include <asm/mach/arch.h> #include <asm/mach/pci.h> #include <mach/orion5x.h> diff --git a/arch/arm/mach-orion5x/ts409-setup.c b/arch/arm/mach-orion5x/ts409-setup.c index 23c9e2e5e550..0fbcc14e09d7 100644 --- a/arch/arm/mach-orion5x/ts409-setup.c +++ b/arch/arm/mach-orion5x/ts409-setup.c @@ -11,7 +11,7 @@ * as published by the Free Software Foundation; either version * 2 of the License, or (at your option) any later version. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -25,7 +25,6 @@ #include <linux/i2c.h> #include <linux/serial_reg.h> #include <asm/mach-types.h> -#include <asm/gpio.h> #include <asm/mach/arch.h> #include <asm/mach/pci.h> #include <mach/orion5x.h> diff --git a/arch/arm/mach-orion5x/wnr854t-setup.c b/arch/arm/mach-orion5x/wnr854t-setup.c index 1c63a76f3ca3..b8be7d8d0cf4 100644 --- a/arch/arm/mach-orion5x/wnr854t-setup.c +++ b/arch/arm/mach-orion5x/wnr854t-setup.c @@ -5,7 +5,7 @@ * License version 2. This program is licensed "as is" without any * warranty of any kind, whether express or implied. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -17,7 +17,6 @@ #include <linux/ethtool.h> #include <net/dsa.h> #include <asm/mach-types.h> -#include <asm/gpio.h> #include <asm/mach/arch.h> #include <asm/mach/pci.h> #include <mach/orion5x.h> diff --git a/arch/arm/mach-orion5x/wrt350n-v2-setup.c b/arch/arm/mach-orion5x/wrt350n-v2-setup.c index 4fd9f18c9d5d..faf81a039360 100644 --- a/arch/arm/mach-orion5x/wrt350n-v2-setup.c +++ b/arch/arm/mach-orion5x/wrt350n-v2-setup.c @@ -5,7 +5,7 @@ * License version 2. This program is licensed "as is" without any * warranty of any kind, whether express or implied. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -20,7 +20,6 @@ #include <linux/input.h> #include <net/dsa.h> #include <asm/mach-types.h> -#include <asm/gpio.h> #include <asm/mach/arch.h> #include <asm/mach/pci.h> #include <mach/orion5x.h> diff --git a/arch/arm/mach-pnx4008/gpio.c b/arch/arm/mach-pnx4008/gpio.c index f219914f5b29..d3e71d3847b4 100644 --- a/arch/arm/mach-pnx4008/gpio.c +++ b/arch/arm/mach-pnx4008/gpio.c @@ -13,14 +13,13 @@ * is licensed "as is" without any warranty of any kind, whether express * or implied. */ - #include <linux/types.h> #include <linux/kernel.h> #include <linux/module.h> #include <linux/io.h> #include <mach/hardware.h> #include <mach/platform.h> -#include <mach/gpio.h> +#include <mach/gpio-pnx4008.h> /* register definitions */ #define PIO_VA_BASE IO_ADDRESS(PNX4008_PIO_BASE) diff --git a/arch/arm/mach-pnx4008/include/mach/gpio.h b/arch/arm/mach-pnx4008/include/mach/gpio-pnx4008.h index 9591467eb9ec..41027dd7cf74 100644 --- a/arch/arm/mach-pnx4008/include/mach/gpio.h +++ b/arch/arm/mach-pnx4008/include/mach/gpio-pnx4008.h @@ -1,5 +1,5 @@ /* - * arch/arm/mach-pnx4008/include/mach/gpio.h + * arch/arm/mach-pnx4008/include/mach/gpio-pnx4008.h * * PNX4008 GPIO driver - header file * diff --git a/arch/arm/mach-pnx4008/serial.c b/arch/arm/mach-pnx4008/serial.c index f40961e51914..374c138ac1ac 100644 --- a/arch/arm/mach-pnx4008/serial.c +++ b/arch/arm/mach-pnx4008/serial.c @@ -9,7 +9,6 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - #include <linux/kernel.h> #include <linux/types.h> #include <linux/io.h> @@ -19,8 +18,8 @@ #include <linux/serial_core.h> #include <linux/serial_reg.h> -#include <mach/gpio.h> +#include <mach/gpio-pnx4008.h> #include <mach/clock.h> #define UART_3 0 diff --git a/arch/arm/mach-pxa/cm-x255.c b/arch/arm/mach-pxa/cm-x255.c index 93f59f877fc6..be751470d37b 100644 --- a/arch/arm/mach-pxa/cm-x255.c +++ b/arch/arm/mach-pxa/cm-x255.c @@ -11,7 +11,6 @@ #include <linux/platform_device.h> #include <linux/irq.h> -#include <linux/gpio.h> #include <linux/mtd/partitions.h> #include <linux/mtd/physmap.h> #include <linux/mtd/nand-gpio.h> diff --git a/arch/arm/mach-pxa/generic.c b/arch/arm/mach-pxa/generic.c index f5d91efc2965..5432ecb15def 100644 --- a/arch/arm/mach-pxa/generic.c +++ b/arch/arm/mach-pxa/generic.c @@ -16,6 +16,7 @@ * initialization stuff for PXA machines which can be overridden later if * need be. */ +#include <linux/gpio.h> #include <linux/module.h> #include <linux/kernel.h> #include <linux/init.h> @@ -26,7 +27,6 @@ #include <asm/mach-types.h> #include <mach/reset.h> -#include <mach/gpio.h> #include <mach/smemc.h> #include <mach/pxa3xx-regs.h> diff --git a/arch/arm/mach-pxa/include/mach/gpio-pxa.h b/arch/arm/mach-pxa/include/mach/gpio-pxa.h new file mode 100644 index 000000000000..41b4c93a96c2 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/gpio-pxa.h @@ -0,0 +1,133 @@ +/* + * Written by Philipp Zabel <philipp.zabel@gmail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + */ +#ifndef __MACH_PXA_GPIO_PXA_H +#define __MACH_PXA_GPIO_PXA_H + +#include <mach/irqs.h> +#include <mach/hardware.h> + +#define GPIO_REGS_VIRT io_p2v(0x40E00000) + +#define BANK_OFF(n) (((n) < 3) ? (n) << 2 : 0x100 + (((n) - 3) << 2)) +#define GPIO_REG(x) (*(volatile u32 *)(GPIO_REGS_VIRT + (x))) + +/* GPIO Pin Level Registers */ +#define GPLR0 GPIO_REG(BANK_OFF(0) + 0x00) +#define GPLR1 GPIO_REG(BANK_OFF(1) + 0x00) +#define GPLR2 GPIO_REG(BANK_OFF(2) + 0x00) +#define GPLR3 GPIO_REG(BANK_OFF(3) + 0x00) + +/* GPIO Pin Direction Registers */ +#define GPDR0 GPIO_REG(BANK_OFF(0) + 0x0c) +#define GPDR1 GPIO_REG(BANK_OFF(1) + 0x0c) +#define GPDR2 GPIO_REG(BANK_OFF(2) + 0x0c) +#define GPDR3 GPIO_REG(BANK_OFF(3) + 0x0c) + +/* GPIO Pin Output Set Registers */ +#define GPSR0 GPIO_REG(BANK_OFF(0) + 0x18) +#define GPSR1 GPIO_REG(BANK_OFF(1) + 0x18) +#define GPSR2 GPIO_REG(BANK_OFF(2) + 0x18) +#define GPSR3 GPIO_REG(BANK_OFF(3) + 0x18) + +/* GPIO Pin Output Clear Registers */ +#define GPCR0 GPIO_REG(BANK_OFF(0) + 0x24) +#define GPCR1 GPIO_REG(BANK_OFF(1) + 0x24) +#define GPCR2 GPIO_REG(BANK_OFF(2) + 0x24) +#define GPCR3 GPIO_REG(BANK_OFF(3) + 0x24) + +/* GPIO Rising Edge Detect Registers */ +#define GRER0 GPIO_REG(BANK_OFF(0) + 0x30) +#define GRER1 GPIO_REG(BANK_OFF(1) + 0x30) +#define GRER2 GPIO_REG(BANK_OFF(2) + 0x30) +#define GRER3 GPIO_REG(BANK_OFF(3) + 0x30) + +/* GPIO Falling Edge Detect Registers */ +#define GFER0 GPIO_REG(BANK_OFF(0) + 0x3c) +#define GFER1 GPIO_REG(BANK_OFF(1) + 0x3c) +#define GFER2 GPIO_REG(BANK_OFF(2) + 0x3c) +#define GFER3 GPIO_REG(BANK_OFF(3) + 0x3c) + +/* GPIO Edge Detect Status Registers */ +#define GEDR0 GPIO_REG(BANK_OFF(0) + 0x48) +#define GEDR1 GPIO_REG(BANK_OFF(1) + 0x48) +#define GEDR2 GPIO_REG(BANK_OFF(2) + 0x48) +#define GEDR3 GPIO_REG(BANK_OFF(3) + 0x48) + +/* GPIO Alternate Function Select Registers */ +#define GAFR0_L GPIO_REG(0x0054) +#define GAFR0_U GPIO_REG(0x0058) +#define GAFR1_L GPIO_REG(0x005C) +#define GAFR1_U GPIO_REG(0x0060) +#define GAFR2_L GPIO_REG(0x0064) +#define GAFR2_U GPIO_REG(0x0068) +#define GAFR3_L GPIO_REG(0x006C) +#define GAFR3_U GPIO_REG(0x0070) + +/* More handy macros. The argument is a literal GPIO number. */ + +#define GPIO_bit(x) (1 << ((x) & 0x1f)) + +#define GPLR(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x00) +#define GPDR(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x0c) +#define GPSR(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x18) +#define GPCR(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x24) +#define GRER(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x30) +#define GFER(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x3c) +#define GEDR(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x48) +#define GAFR(x) GPIO_REG(0x54 + (((x) & 0x70) >> 2)) + + +#define NR_BUILTIN_GPIO PXA_GPIO_IRQ_NUM + +#define gpio_to_bank(gpio) ((gpio) >> 5) + +#ifdef CONFIG_CPU_PXA26x +/* GPIO86/87/88/89 on PXA26x have their direction bits in GPDR2 inverted, + * as well as their Alternate Function value being '1' for GPIO in GAFRx. + */ +static inline int __gpio_is_inverted(unsigned gpio) +{ + return cpu_is_pxa25x() && gpio > 85; +} +#else +static inline int __gpio_is_inverted(unsigned gpio) { return 0; } +#endif + +/* + * On PXA25x and PXA27x, GAFRx and GPDRx together decide the alternate + * function of a GPIO, and GPDRx cannot be altered once configured. It + * is attributed as "occupied" here (I know this terminology isn't + * accurate, you are welcome to propose a better one :-) + */ +static inline int __gpio_is_occupied(unsigned gpio) +{ + if (cpu_is_pxa27x() || cpu_is_pxa25x()) { + int af = (GAFR(gpio) >> ((gpio & 0xf) * 2)) & 0x3; + int dir = GPDR(gpio) & GPIO_bit(gpio); + + if (__gpio_is_inverted(gpio)) + return af != 1 || dir == 0; + else + return af != 0 || dir != 0; + } else + return GPDR(gpio) & GPIO_bit(gpio); +} + +#include <plat/gpio-pxa.h> +#endif /* __MACH_PXA_GPIO_PXA_H */ diff --git a/arch/arm/mach-pxa/include/mach/gpio.h b/arch/arm/mach-pxa/include/mach/gpio.h index c4639502efca..004cade7bb13 100644 --- a/arch/arm/mach-pxa/include/mach/gpio.h +++ b/arch/arm/mach-pxa/include/mach/gpio.h @@ -24,84 +24,10 @@ #ifndef __ASM_ARCH_PXA_GPIO_H #define __ASM_ARCH_PXA_GPIO_H -#include <mach/irqs.h> -#include <mach/hardware.h> #include <asm-generic/gpio.h> +/* The defines for the driver are needed for the accelerated accessors */ +#include "gpio-pxa.h" -#define GPIO_REGS_VIRT io_p2v(0x40E00000) - -#define BANK_OFF(n) (((n) < 3) ? (n) << 2 : 0x100 + (((n) - 3) << 2)) -#define GPIO_REG(x) (*(volatile u32 *)(GPIO_REGS_VIRT + (x))) - -/* GPIO Pin Level Registers */ -#define GPLR0 GPIO_REG(BANK_OFF(0) + 0x00) -#define GPLR1 GPIO_REG(BANK_OFF(1) + 0x00) -#define GPLR2 GPIO_REG(BANK_OFF(2) + 0x00) -#define GPLR3 GPIO_REG(BANK_OFF(3) + 0x00) - -/* GPIO Pin Direction Registers */ -#define GPDR0 GPIO_REG(BANK_OFF(0) + 0x0c) -#define GPDR1 GPIO_REG(BANK_OFF(1) + 0x0c) -#define GPDR2 GPIO_REG(BANK_OFF(2) + 0x0c) -#define GPDR3 GPIO_REG(BANK_OFF(3) + 0x0c) - -/* GPIO Pin Output Set Registers */ -#define GPSR0 GPIO_REG(BANK_OFF(0) + 0x18) -#define GPSR1 GPIO_REG(BANK_OFF(1) + 0x18) -#define GPSR2 GPIO_REG(BANK_OFF(2) + 0x18) -#define GPSR3 GPIO_REG(BANK_OFF(3) + 0x18) - -/* GPIO Pin Output Clear Registers */ -#define GPCR0 GPIO_REG(BANK_OFF(0) + 0x24) -#define GPCR1 GPIO_REG(BANK_OFF(1) + 0x24) -#define GPCR2 GPIO_REG(BANK_OFF(2) + 0x24) -#define GPCR3 GPIO_REG(BANK_OFF(3) + 0x24) - -/* GPIO Rising Edge Detect Registers */ -#define GRER0 GPIO_REG(BANK_OFF(0) + 0x30) -#define GRER1 GPIO_REG(BANK_OFF(1) + 0x30) -#define GRER2 GPIO_REG(BANK_OFF(2) + 0x30) -#define GRER3 GPIO_REG(BANK_OFF(3) + 0x30) - -/* GPIO Falling Edge Detect Registers */ -#define GFER0 GPIO_REG(BANK_OFF(0) + 0x3c) -#define GFER1 GPIO_REG(BANK_OFF(1) + 0x3c) -#define GFER2 GPIO_REG(BANK_OFF(2) + 0x3c) -#define GFER3 GPIO_REG(BANK_OFF(3) + 0x3c) - -/* GPIO Edge Detect Status Registers */ -#define GEDR0 GPIO_REG(BANK_OFF(0) + 0x48) -#define GEDR1 GPIO_REG(BANK_OFF(1) + 0x48) -#define GEDR2 GPIO_REG(BANK_OFF(2) + 0x48) -#define GEDR3 GPIO_REG(BANK_OFF(3) + 0x48) - -/* GPIO Alternate Function Select Registers */ -#define GAFR0_L GPIO_REG(0x0054) -#define GAFR0_U GPIO_REG(0x0058) -#define GAFR1_L GPIO_REG(0x005C) -#define GAFR1_U GPIO_REG(0x0060) -#define GAFR2_L GPIO_REG(0x0064) -#define GAFR2_U GPIO_REG(0x0068) -#define GAFR3_L GPIO_REG(0x006C) -#define GAFR3_U GPIO_REG(0x0070) - -/* More handy macros. The argument is a literal GPIO number. */ - -#define GPIO_bit(x) (1 << ((x) & 0x1f)) - -#define GPLR(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x00) -#define GPDR(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x0c) -#define GPSR(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x18) -#define GPCR(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x24) -#define GRER(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x30) -#define GFER(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x3c) -#define GEDR(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x48) -#define GAFR(x) GPIO_REG(0x54 + (((x) & 0x70) >> 2)) - - -#define NR_BUILTIN_GPIO PXA_GPIO_IRQ_NUM - -#define gpio_to_bank(gpio) ((gpio) >> 5) #define gpio_to_irq(gpio) IRQ_GPIO(gpio) static inline int irq_to_gpio(unsigned int irq) @@ -118,37 +44,5 @@ static inline int irq_to_gpio(unsigned int irq) return -1; } -#ifdef CONFIG_CPU_PXA26x -/* GPIO86/87/88/89 on PXA26x have their direction bits in GPDR2 inverted, - * as well as their Alternate Function value being '1' for GPIO in GAFRx. - */ -static inline int __gpio_is_inverted(unsigned gpio) -{ - return cpu_is_pxa25x() && gpio > 85; -} -#else -static inline int __gpio_is_inverted(unsigned gpio) { return 0; } -#endif - -/* - * On PXA25x and PXA27x, GAFRx and GPDRx together decide the alternate - * function of a GPIO, and GPDRx cannot be altered once configured. It - * is attributed as "occupied" here (I know this terminology isn't - * accurate, you are welcome to propose a better one :-) - */ -static inline int __gpio_is_occupied(unsigned gpio) -{ - if (cpu_is_pxa27x() || cpu_is_pxa25x()) { - int af = (GAFR(gpio) >> ((gpio & 0xf) * 2)) & 0x3; - int dir = GPDR(gpio) & GPIO_bit(gpio); - - if (__gpio_is_inverted(gpio)) - return af != 1 || dir == 0; - else - return af != 0 || dir != 0; - } else - return GPDR(gpio) & GPIO_bit(gpio); -} - #include <plat/gpio.h> #endif diff --git a/arch/arm/mach-pxa/include/mach/littleton.h b/arch/arm/mach-pxa/include/mach/littleton.h index 2a5726c15e0e..b6238cbd8aea 100644 --- a/arch/arm/mach-pxa/include/mach/littleton.h +++ b/arch/arm/mach-pxa/include/mach/littleton.h @@ -1,7 +1,7 @@ #ifndef __ASM_ARCH_LITTLETON_H #define __ASM_ARCH_LITTLETON_H -#include <mach/gpio.h> +#include <mach/gpio-pxa.h> #define LITTLETON_ETH_PHYS 0x30000000 diff --git a/arch/arm/mach-pxa/irq.c b/arch/arm/mach-pxa/irq.c index ca6075717824..8d9200f92268 100644 --- a/arch/arm/mach-pxa/irq.c +++ b/arch/arm/mach-pxa/irq.c @@ -11,7 +11,6 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - #include <linux/init.h> #include <linux/module.h> #include <linux/interrupt.h> @@ -23,7 +22,7 @@ #include <mach/hardware.h> #include <mach/irqs.h> -#include <mach/gpio.h> +#include <mach/gpio-pxa.h> #include "generic.h" diff --git a/arch/arm/mach-pxa/lpd270.c b/arch/arm/mach-pxa/lpd270.c index 16df0fc0879a..64540d908958 100644 --- a/arch/arm/mach-pxa/lpd270.c +++ b/arch/arm/mach-pxa/lpd270.c @@ -12,7 +12,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/init.h> #include <linux/platform_device.h> #include <linux/syscore_ops.h> @@ -39,7 +39,6 @@ #include <asm/mach/flash.h> #include <mach/pxa27x.h> -#include <mach/gpio.h> #include <mach/lpd270.h> #include <mach/audio.h> #include <mach/pxafb.h> diff --git a/arch/arm/mach-pxa/lubbock.c b/arch/arm/mach-pxa/lubbock.c index a8c696bfc132..c48ce6da9184 100644 --- a/arch/arm/mach-pxa/lubbock.c +++ b/arch/arm/mach-pxa/lubbock.c @@ -11,6 +11,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ +#include <linux/gpio.h> #include <linux/module.h> #include <linux/kernel.h> #include <linux/init.h> @@ -42,7 +43,6 @@ #include <asm/hardware/sa1111.h> #include <mach/pxa25x.h> -#include <mach/gpio.h> #include <mach/audio.h> #include <mach/lubbock.h> #include <mach/udc.h> diff --git a/arch/arm/mach-pxa/mainstone.c b/arch/arm/mach-pxa/mainstone.c index cc6e14f6d114..0567d3965fda 100644 --- a/arch/arm/mach-pxa/mainstone.c +++ b/arch/arm/mach-pxa/mainstone.c @@ -12,7 +12,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/init.h> #include <linux/platform_device.h> #include <linux/syscore_ops.h> @@ -43,7 +43,6 @@ #include <asm/mach/flash.h> #include <mach/pxa27x.h> -#include <mach/gpio.h> #include <mach/mainstone.h> #include <mach/audio.h> #include <mach/pxafb.h> diff --git a/arch/arm/mach-pxa/mfp-pxa2xx.c b/arch/arm/mach-pxa/mfp-pxa2xx.c index b27544bcafcb..43a5f6861ca3 100644 --- a/arch/arm/mach-pxa/mfp-pxa2xx.c +++ b/arch/arm/mach-pxa/mfp-pxa2xx.c @@ -12,15 +12,15 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/module.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/syscore_ops.h> -#include <mach/gpio.h> #include <mach/pxa2xx-regs.h> #include <mach/mfp-pxa2xx.h> +#include <mach/gpio-pxa.h> #include "generic.h" diff --git a/arch/arm/mach-pxa/pcm990-baseboard.c b/arch/arm/mach-pxa/pcm990-baseboard.c index 6d5b7e062124..9a9c539f6c01 100644 --- a/arch/arm/mach-pxa/pcm990-baseboard.c +++ b/arch/arm/mach-pxa/pcm990-baseboard.c @@ -19,7 +19,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/irq.h> #include <linux/platform_device.h> #include <linux/i2c.h> @@ -28,7 +28,6 @@ #include <media/soc_camera.h> -#include <asm/gpio.h> #include <mach/camera.h> #include <asm/mach/map.h> #include <mach/pxa27x.h> diff --git a/arch/arm/mach-pxa/pxa25x.c b/arch/arm/mach-pxa/pxa25x.c index 9c434d21a271..8746e1090b6e 100644 --- a/arch/arm/mach-pxa/pxa25x.c +++ b/arch/arm/mach-pxa/pxa25x.c @@ -16,6 +16,7 @@ * initialization stuff for PXA machines which can be overridden later if * need be. */ +#include <linux/gpio.h> #include <linux/module.h> #include <linux/kernel.h> #include <linux/init.h> @@ -23,12 +24,12 @@ #include <linux/suspend.h> #include <linux/syscore_ops.h> #include <linux/irq.h> +#include <linux/gpio.h> #include <asm/mach/map.h> #include <asm/suspend.h> #include <mach/hardware.h> #include <mach/irqs.h> -#include <mach/gpio.h> #include <mach/pxa25x.h> #include <mach/reset.h> #include <mach/pm.h> diff --git a/arch/arm/mach-pxa/pxa27x.c b/arch/arm/mach-pxa/pxa27x.c index 9d2400b5f503..2bb5cf8ba6ec 100644 --- a/arch/arm/mach-pxa/pxa27x.c +++ b/arch/arm/mach-pxa/pxa27x.c @@ -11,6 +11,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ +#include <linux/gpio.h> #include <linux/module.h> #include <linux/kernel.h> #include <linux/init.h> @@ -20,13 +21,13 @@ #include <linux/io.h> #include <linux/irq.h> #include <linux/i2c/pxa-i2c.h> +#include <linux/gpio.h> #include <asm/mach/map.h> #include <mach/hardware.h> #include <asm/irq.h> #include <asm/suspend.h> #include <mach/irqs.h> -#include <mach/gpio.h> #include <mach/pxa27x.h> #include <mach/reset.h> #include <mach/ohci.h> diff --git a/arch/arm/mach-pxa/pxa3xx.c b/arch/arm/mach-pxa/pxa3xx.c index b5cd9e5aba31..f940a1345531 100644 --- a/arch/arm/mach-pxa/pxa3xx.c +++ b/arch/arm/mach-pxa/pxa3xx.c @@ -12,7 +12,6 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - #include <linux/module.h> #include <linux/kernel.h> #include <linux/init.h> @@ -26,7 +25,7 @@ #include <asm/mach/map.h> #include <asm/suspend.h> #include <mach/hardware.h> -#include <mach/gpio.h> +#include <mach/gpio-pxa.h> #include <mach/pxa3xx-regs.h> #include <mach/reset.h> #include <mach/ohci.h> diff --git a/arch/arm/mach-pxa/pxa95x.c b/arch/arm/mach-pxa/pxa95x.c index 0ee166b61f81..51371b39d2a3 100644 --- a/arch/arm/mach-pxa/pxa95x.c +++ b/arch/arm/mach-pxa/pxa95x.c @@ -9,7 +9,6 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - #include <linux/module.h> #include <linux/kernel.h> #include <linux/init.h> @@ -21,7 +20,7 @@ #include <linux/syscore_ops.h> #include <mach/hardware.h> -#include <mach/gpio.h> +#include <mach/gpio-pxa.h> #include <mach/pxa3xx-regs.h> #include <mach/pxa930.h> #include <mach/reset.h> diff --git a/arch/arm/mach-pxa/saarb.c b/arch/arm/mach-pxa/saarb.c index 5ce340320ab9..3c988b6f718f 100644 --- a/arch/arm/mach-pxa/saarb.c +++ b/arch/arm/mach-pxa/saarb.c @@ -9,12 +9,13 @@ * it under the terms of the GNU General Public License version 2 as * publishhed by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/init.h> #include <linux/kernel.h> #include <linux/i2c.h> #include <linux/i2c/pxa-i2c.h> #include <linux/mfd/88pm860x.h> +#include <linux/gpio.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> @@ -23,7 +24,6 @@ #include <mach/hardware.h> #include <mach/mfp.h> #include <mach/mfp-pxa930.h> -#include <mach/gpio.h> #include "generic.h" diff --git a/arch/arm/mach-realview/include/mach/gpio.h b/arch/arm/mach-realview/include/mach/gpio.h index 94ff27678a46..40a8c178f10d 100644 --- a/arch/arm/mach-realview/include/mach/gpio.h +++ b/arch/arm/mach-realview/include/mach/gpio.h @@ -1,6 +1 @@ -#include <asm-generic/gpio.h> - -#define gpio_get_value __gpio_get_value -#define gpio_set_value __gpio_set_value -#define gpio_cansleep __gpio_cansleep -#define gpio_to_irq __gpio_to_irq +/* empty */ diff --git a/arch/arm/mach-rpc/include/mach/hardware.h b/arch/arm/mach-rpc/include/mach/hardware.h index dde6b3c0e299..050d63c74cc1 100644 --- a/arch/arm/mach-rpc/include/mach/hardware.h +++ b/arch/arm/mach-rpc/include/mach/hardware.h @@ -36,7 +36,7 @@ #define EASI_SIZE 0x08000000 /* EASI I/O */ #define EASI_START 0x08000000 -#define EASI_BASE 0xe5000000 +#define EASI_BASE IOMEM(0xe5000000) #define IO_START 0x03000000 /* I/O */ #define IO_SIZE 0x01000000 @@ -51,21 +51,20 @@ /* * IO Addresses */ -#define VIDC_BASE IOMEM(0xe0400000) -#define EXPMASK_BASE 0xe0360000 -#define IOMD_BASE IOMEM(0xe0200000) -#define IOC_BASE IOMEM(0xe0200000) -#define PCIO_BASE IOMEM(0xe0010000) -#define FLOPPYDMA_BASE IOMEM(0xe002a000) +#define ECARD_EASI_BASE (EASI_BASE) +#define VIDC_BASE (IO_BASE + 0x00400000) +#define EXPMASK_BASE (IO_BASE + 0x00360000) +#define ECARD_IOC4_BASE (IO_BASE + 0x00270000) +#define ECARD_IOC_BASE (IO_BASE + 0x00240000) +#define IOMD_BASE (IO_BASE + 0x00200000) +#define IOC_BASE (IO_BASE + 0x00200000) +#define ECARD_MEMC8_BASE (IO_BASE + 0x0002b000) +#define FLOPPYDMA_BASE (IO_BASE + 0x0002a000) +#define PCIO_BASE (IO_BASE + 0x00010000) +#define ECARD_MEMC_BASE (IO_BASE + 0x00000000) #define vidc_writel(val) __raw_writel(val, VIDC_BASE) -#define IO_EC_EASI_BASE 0x81400000 -#define IO_EC_IOC4_BASE 0x8009c000 -#define IO_EC_IOC_BASE 0x80090000 -#define IO_EC_MEMC8_BASE 0x8000ac00 -#define IO_EC_MEMC_BASE 0x80000000 - #define NETSLOT_BASE 0x0302b000 #define NETSLOT_SIZE 0x00001000 diff --git a/arch/arm/mach-rpc/include/mach/io.h b/arch/arm/mach-rpc/include/mach/io.h index 20da7f486e51..695f4ed2e11b 100644 --- a/arch/arm/mach-rpc/include/mach/io.h +++ b/arch/arm/mach-rpc/include/mach/io.h @@ -15,195 +15,18 @@ #include <mach/hardware.h> -#define IO_SPACE_LIMIT 0xffffffff +#define IO_SPACE_LIMIT 0xffff /* - * We use two different types of addressing - PC style addresses, and ARM - * addresses. PC style accesses the PC hardware with the normal PC IO - * addresses, eg 0x3f8 for serial#1. ARM addresses are 0x80000000+ - * and are translated to the start of IO. Note that all addresses are - * shifted left! - */ -#define __PORT_PCIO(x) (!((x) & 0x80000000)) - -/* - * Dynamic IO functions. - */ -static inline void __outb (unsigned int value, unsigned int port) -{ - unsigned long temp; - __asm__ __volatile__( - "tst %2, #0x80000000\n\t" - "mov %0, %4\n\t" - "addeq %0, %0, %3\n\t" - "strb %1, [%0, %2, lsl #2] @ outb" - : "=&r" (temp) - : "r" (value), "r" (port), "Ir" (PCIO_BASE - IO_BASE), "Ir" (IO_BASE) - : "cc"); -} - -static inline void __outw (unsigned int value, unsigned int port) -{ - unsigned long temp; - __asm__ __volatile__( - "tst %2, #0x80000000\n\t" - "mov %0, %4\n\t" - "addeq %0, %0, %3\n\t" - "str %1, [%0, %2, lsl #2] @ outw" - : "=&r" (temp) - : "r" (value|value<<16), "r" (port), "Ir" (PCIO_BASE - IO_BASE), "Ir" (IO_BASE) - : "cc"); -} - -static inline void __outl (unsigned int value, unsigned int port) -{ - unsigned long temp; - __asm__ __volatile__( - "tst %2, #0x80000000\n\t" - "mov %0, %4\n\t" - "addeq %0, %0, %3\n\t" - "str %1, [%0, %2, lsl #2] @ outl" - : "=&r" (temp) - : "r" (value), "r" (port), "Ir" (PCIO_BASE - IO_BASE), "Ir" (IO_BASE) - : "cc"); -} - -#define DECLARE_DYN_IN(sz,fnsuffix,instr) \ -static inline unsigned sz __in##fnsuffix (unsigned int port) \ -{ \ - unsigned long temp, value; \ - __asm__ __volatile__( \ - "tst %2, #0x80000000\n\t" \ - "mov %0, %4\n\t" \ - "addeq %0, %0, %3\n\t" \ - "ldr" instr " %1, [%0, %2, lsl #2] @ in" #fnsuffix \ - : "=&r" (temp), "=r" (value) \ - : "r" (port), "Ir" (PCIO_BASE - IO_BASE), "Ir" (IO_BASE) \ - : "cc"); \ - return (unsigned sz)value; \ -} - -static inline void __iomem *__deprecated __ioaddr(unsigned int port) -{ - void __iomem *ret; - if (__PORT_PCIO(port)) - ret = PCIO_BASE; - else - ret = IO_BASE; - return ret + (port << 2); -} - -#define DECLARE_IO(sz,fnsuffix,instr) \ - DECLARE_DYN_IN(sz,fnsuffix,instr) - -DECLARE_IO(char,b,"b") -DECLARE_IO(short,w,"") -DECLARE_IO(int,l,"") - -#undef DECLARE_IO -#undef DECLARE_DYN_IN - -/* - * Constant address IO functions + * We need PC style IO addressing for: + * - floppy (at 0x3f2,0x3f4,0x3f5,0x3f7) + * - parport (at 0x278-0x27a, 0x27b-0x27f, 0x778-0x77a) + * - 8250 serial (only for compile) * - * These have to be macros for the 'J' constraint to work - - * +/-4096 immediate operand. + * These peripherals are found in an area of MMIO which looks very much + * like an ISA bus, but with registers at the low byte of each word. */ -#define __outbc(value,port) \ -({ \ - if (__PORT_PCIO((port))) \ - __asm__ __volatile__( \ - "strb %0, [%1, %2] @ outbc" \ - : : "r" (value), "r" (PCIO_BASE), "Jr" ((port) << 2)); \ - else \ - __asm__ __volatile__( \ - "strb %0, [%1, %2] @ outbc" \ - : : "r" (value), "r" (IO_BASE), "r" ((port) << 2)); \ -}) - -#define __inbc(port) \ -({ \ - unsigned char result; \ - if (__PORT_PCIO((port))) \ - __asm__ __volatile__( \ - "ldrb %0, [%1, %2] @ inbc" \ - : "=r" (result) : "r" (PCIO_BASE), "Jr" ((port) << 2)); \ - else \ - __asm__ __volatile__( \ - "ldrb %0, [%1, %2] @ inbc" \ - : "=r" (result) : "r" (IO_BASE), "r" ((port) << 2)); \ - result; \ -}) - -#define __outwc(value,port) \ -({ \ - unsigned long __v = value; \ - if (__PORT_PCIO((port))) \ - __asm__ __volatile__( \ - "str %0, [%1, %2] @ outwc" \ - : : "r" (__v|__v<<16), "r" (PCIO_BASE), "Jr" ((port) << 2)); \ - else \ - __asm__ __volatile__( \ - "str %0, [%1, %2] @ outwc" \ - : : "r" (__v|__v<<16), "r" (IO_BASE), "r" ((port) << 2)); \ -}) - -#define __inwc(port) \ -({ \ - unsigned short result; \ - if (__PORT_PCIO((port))) \ - __asm__ __volatile__( \ - "ldr %0, [%1, %2] @ inwc" \ - : "=r" (result) : "r" (PCIO_BASE), "Jr" ((port) << 2)); \ - else \ - __asm__ __volatile__( \ - "ldr %0, [%1, %2] @ inwc" \ - : "=r" (result) : "r" (IO_BASE), "r" ((port) << 2)); \ - result & 0xffff; \ -}) - -#define __outlc(value,port) \ -({ \ - unsigned long __v = value; \ - if (__PORT_PCIO((port))) \ - __asm__ __volatile__( \ - "str %0, [%1, %2] @ outlc" \ - : : "r" (__v), "r" (PCIO_BASE), "Jr" ((port) << 2)); \ - else \ - __asm__ __volatile__( \ - "str %0, [%1, %2] @ outlc" \ - : : "r" (__v), "r" (IO_BASE), "r" ((port) << 2)); \ -}) - -#define __inlc(port) \ -({ \ - unsigned long result; \ - if (__PORT_PCIO((port))) \ - __asm__ __volatile__( \ - "ldr %0, [%1, %2] @ inlc" \ - : "=r" (result) : "r" (PCIO_BASE), "Jr" ((port) << 2)); \ - else \ - __asm__ __volatile__( \ - "ldr %0, [%1, %2] @ inlc" \ - : "=r" (result) : "r" (IO_BASE), "r" ((port) << 2)); \ - result; \ -}) - -#define inb(p) (__builtin_constant_p((p)) ? __inbc(p) : __inb(p)) -#define inw(p) (__builtin_constant_p((p)) ? __inwc(p) : __inw(p)) -#define inl(p) (__builtin_constant_p((p)) ? __inlc(p) : __inl(p)) -#define outb(v,p) (__builtin_constant_p((p)) ? __outbc(v,p) : __outb(v,p)) -#define outw(v,p) (__builtin_constant_p((p)) ? __outwc(v,p) : __outw(v,p)) -#define outl(v,p) (__builtin_constant_p((p)) ? __outlc(v,p) : __outl(v,p)) - -/* the following macro is deprecated */ -#define ioaddr(port) ((unsigned long)__ioaddr((port))) - -#define insb(p,d,l) __raw_readsb(__ioaddr(p),d,l) -#define insw(p,d,l) __raw_readsw(__ioaddr(p),d,l) - -#define outsb(p,d,l) __raw_writesb(__ioaddr(p),d,l) -#define outsw(p,d,l) __raw_writesw(__ioaddr(p),d,l) +#define __io(a) (PCIO_BASE + ((a) << 2)) /* * 1:1 mapping for ioremapped regions. diff --git a/arch/arm/mach-rpc/riscpc.c b/arch/arm/mach-rpc/riscpc.c index a9241eb87724..8559598ab767 100644 --- a/arch/arm/mach-rpc/riscpc.c +++ b/arch/arm/mach-rpc/riscpc.c @@ -74,7 +74,7 @@ static struct map_desc rpc_io_desc[] __initdata = { .length = IO_SIZE , .type = MT_DEVICE }, { /* EASI space */ - .virtual = EASI_BASE, + .virtual = (unsigned long)EASI_BASE, .pfn = __phys_to_pfn(EASI_START), .length = EASI_SIZE, .type = MT_DEVICE diff --git a/arch/arm/mach-s3c2410/include/mach/gpio.h b/arch/arm/mach-s3c2410/include/mach/gpio.h index f7f6b07df30e..6fac70f3484e 100644 --- a/arch/arm/mach-s3c2410/include/mach/gpio.h +++ b/arch/arm/mach-s3c2410/include/mach/gpio.h @@ -11,11 +11,6 @@ * published by the Free Software Foundation. */ -#define gpio_get_value __gpio_get_value -#define gpio_set_value __gpio_set_value -#define gpio_cansleep __gpio_cansleep -#define gpio_to_irq __gpio_to_irq - /* some boards require extra gpio capacity to support external * devices that need GPIO. */ @@ -28,7 +23,6 @@ #define ARCH_NR_GPIOS (256 + CONFIG_S3C24XX_GPIO_EXTRA) #endif -#include <asm-generic/gpio.h> #include <mach/gpio-nrs.h> #include <mach/gpio-fns.h> diff --git a/arch/arm/mach-s3c2410/include/mach/h1940-latch.h b/arch/arm/mach-s3c2410/include/mach/h1940-latch.h index 97e42bfce81e..fc897d3a056c 100644 --- a/arch/arm/mach-s3c2410/include/mach/h1940-latch.h +++ b/arch/arm/mach-s3c2410/include/mach/h1940-latch.h @@ -14,7 +14,7 @@ #ifndef __ASM_ARCH_H1940_LATCH_H #define __ASM_ARCH_H1940_LATCH_H -#include <mach/gpio.h> +#include <asm/gpio.h> #define H1940_LATCH_GPIO(x) (S3C_GPIO_END + (x)) diff --git a/arch/arm/mach-s3c2410/include/mach/io.h b/arch/arm/mach-s3c2410/include/mach/io.h index 9813dbf2ae4f..118749f37c4c 100644 --- a/arch/arm/mach-s3c2410/include/mach/io.h +++ b/arch/arm/mach-s3c2410/include/mach/io.h @@ -199,8 +199,6 @@ DECLARE_IO(int,l,"") #define outw(v,p) (__builtin_constant_p((p)) ? __outwc(v,p) : __outw(v,p)) #define outl(v,p) (__builtin_constant_p((p)) ? __outlc(v,p) : __outl(v,p)) #define __ioaddr(p) (__builtin_constant_p((p)) ? __ioaddr(p) : __ioaddrc(p)) -/* the following macro is deprecated */ -#define ioaddr(port) __ioaddr((port)) #define insb(p,d,l) __raw_readsb(__ioaddr(p),d,l) #define insw(p,d,l) __raw_readsw(__ioaddr(p),d,l) diff --git a/arch/arm/mach-s3c64xx/include/mach/gpio.h b/arch/arm/mach-s3c64xx/include/mach/gpio.h index 0d46e994048a..6e34c2f6e670 100644 --- a/arch/arm/mach-s3c64xx/include/mach/gpio.h +++ b/arch/arm/mach-s3c64xx/include/mach/gpio.h @@ -12,11 +12,6 @@ * published by the Free Software Foundation. */ -#define gpio_get_value __gpio_get_value -#define gpio_set_value __gpio_set_value -#define gpio_cansleep __gpio_cansleep -#define gpio_to_irq __gpio_to_irq - /* GPIO bank sizes */ #define S3C64XX_GPIO_A_NR (8) #define S3C64XX_GPIO_B_NR (7) @@ -96,5 +91,3 @@ enum s3c_gpio_number { #define BOARD_NR_GPIOS 16 #define ARCH_NR_GPIOS (GPIO_BOARD_START + BOARD_NR_GPIOS) - -#include <asm-generic/gpio.h> diff --git a/arch/arm/mach-s5p64x0/include/mach/gpio.h b/arch/arm/mach-s5p64x0/include/mach/gpio.h index adb5f298ead8..06cd3c9b16ac 100644 --- a/arch/arm/mach-s5p64x0/include/mach/gpio.h +++ b/arch/arm/mach-s5p64x0/include/mach/gpio.h @@ -13,11 +13,6 @@ #ifndef __ASM_ARCH_GPIO_H #define __ASM_ARCH_GPIO_H __FILE__ -#define gpio_get_value __gpio_get_value -#define gpio_set_value __gpio_set_value -#define gpio_cansleep __gpio_cansleep -#define gpio_to_irq __gpio_to_irq - /* GPIO bank sizes */ #define S5P6440_GPIO_A_NR (6) @@ -134,6 +129,4 @@ enum s5p6450_gpio_number { #define ARCH_NR_GPIOS (S5P64X0_GPIO_END + CONFIG_SAMSUNG_GPIO_EXTRA) -#include <asm-generic/gpio.h> - #endif /* __ASM_ARCH_GPIO_H */ diff --git a/arch/arm/mach-s5pc100/include/mach/gpio.h b/arch/arm/mach-s5pc100/include/mach/gpio.h index 29a8a12d9b4f..5e1a924b595f 100644 --- a/arch/arm/mach-s5pc100/include/mach/gpio.h +++ b/arch/arm/mach-s5pc100/include/mach/gpio.h @@ -15,11 +15,6 @@ #ifndef __ASM_ARCH_GPIO_H #define __ASM_ARCH_GPIO_H __FILE__ -#define gpio_get_value __gpio_get_value -#define gpio_set_value __gpio_set_value -#define gpio_cansleep __gpio_cansleep -#define gpio_to_irq __gpio_to_irq - /* GPIO bank sizes */ #define S5PC100_GPIO_A0_NR (8) #define S5PC100_GPIO_A1_NR (5) @@ -146,6 +141,4 @@ enum s5p_gpio_number { /* define the number of gpios we need to the one after the MP04() range */ #define ARCH_NR_GPIOS (S5PC100_GPIO_END + 1) -#include <asm-generic/gpio.h> - #endif /* __ASM_ARCH_GPIO_H */ diff --git a/arch/arm/mach-s5pv210/include/mach/gpio.h b/arch/arm/mach-s5pv210/include/mach/gpio.h index a5a1e331f8ed..6c8b903c02e4 100644 --- a/arch/arm/mach-s5pv210/include/mach/gpio.h +++ b/arch/arm/mach-s5pv210/include/mach/gpio.h @@ -13,11 +13,6 @@ #ifndef __ASM_ARCH_GPIO_H #define __ASM_ARCH_GPIO_H __FILE__ -#define gpio_get_value __gpio_get_value -#define gpio_set_value __gpio_set_value -#define gpio_cansleep __gpio_cansleep -#define gpio_to_irq __gpio_to_irq - /* Practically, GPIO banks up to MP03 are the configurable gpio banks */ /* GPIO bank sizes */ @@ -142,6 +137,4 @@ enum s5p_gpio_number { #define ARCH_NR_GPIOS (S5PV210_MP05(S5PV210_GPIO_MP05_NR) + \ CONFIG_SAMSUNG_GPIO_EXTRA + 1) -#include <asm-generic/gpio.h> - #endif /* __ASM_ARCH_GPIO_H */ diff --git a/arch/arm/mach-sa1100/Makefile b/arch/arm/mach-sa1100/Makefile index 41252d22e659..73a5c6431792 100644 --- a/arch/arm/mach-sa1100/Makefile +++ b/arch/arm/mach-sa1100/Makefile @@ -3,7 +3,7 @@ # # Common support -obj-y := clock.o generic.o gpio.o irq.o dma.o time.o #nmi-oopser.o +obj-y := clock.o generic.o irq.o dma.o time.o #nmi-oopser.o obj-m := obj-n := obj- := diff --git a/arch/arm/mach-sa1100/generic.c b/arch/arm/mach-sa1100/generic.c index e21f3470eece..5fa5ae1f39e1 100644 --- a/arch/arm/mach-sa1100/generic.c +++ b/arch/arm/mach-sa1100/generic.c @@ -9,6 +9,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ +#include <linux/gpio.h> #include <linux/module.h> #include <linux/kernel.h> #include <linux/init.h> @@ -24,7 +25,6 @@ #include <asm/mach/map.h> #include <asm/mach/flash.h> #include <asm/irq.h> -#include <asm/gpio.h> #include "generic.h" diff --git a/arch/arm/mach-sa1100/include/mach/gpio.h b/arch/arm/mach-sa1100/include/mach/gpio.h index 7befc104e9a9..703631887c94 100644 --- a/arch/arm/mach-sa1100/include/mach/gpio.h +++ b/arch/arm/mach-sa1100/include/mach/gpio.h @@ -28,6 +28,8 @@ #include <asm/irq.h> #include <asm-generic/gpio.h> +#define __ARM_GPIOLIB_COMPLEX + static inline int gpio_get_value(unsigned gpio) { if (__builtin_constant_p(gpio) && (gpio <= GPIO_MAX)) @@ -51,7 +53,5 @@ static inline void gpio_set_value(unsigned gpio, int value) #define gpio_to_irq(gpio) ((gpio < 11) ? (IRQ_GPIO0 + gpio) : \ (IRQ_GPIO11 - 11 + gpio)) -#define irq_to_gpio(irq) ((irq < IRQ_GPIO11_27) ? (irq - IRQ_GPIO0) : \ - (irq - IRQ_GPIO11 + 11)) #endif diff --git a/arch/arm/mach-sa1100/include/mach/io.h b/arch/arm/mach-sa1100/include/mach/io.h index d8b43f3dcd2d..dfc27ff08344 100644 --- a/arch/arm/mach-sa1100/include/mach/io.h +++ b/arch/arm/mach-sa1100/include/mach/io.h @@ -10,11 +10,9 @@ #ifndef __ASM_ARM_ARCH_IO_H #define __ASM_ARM_ARCH_IO_H -#define IO_SPACE_LIMIT 0xffffffff - /* - * We don't actually have real ISA nor PCI buses, but there is so many - * drivers out there that might just work if we fake them... + * __io() is required to be an equivalent mapping to __mem_pci() for + * SOC_COMMON to work. */ #define __io(a) __typesafe_io(a) #define __mem_pci(a) (a) diff --git a/arch/arm/mach-shmobile/include/mach/gpio.h b/arch/arm/mach-shmobile/include/mach/gpio.h index 2b1bb9e43dda..7bf0890e16ba 100644 --- a/arch/arm/mach-shmobile/include/mach/gpio.h +++ b/arch/arm/mach-shmobile/include/mach/gpio.h @@ -18,31 +18,15 @@ #ifdef CONFIG_GPIOLIB -static inline int gpio_get_value(unsigned gpio) -{ - return __gpio_get_value(gpio); -} - -static inline void gpio_set_value(unsigned gpio, int value) -{ - __gpio_set_value(gpio, value); -} - -static inline int gpio_cansleep(unsigned gpio) -{ - return __gpio_cansleep(gpio); -} - -static inline int gpio_to_irq(unsigned gpio) -{ - return __gpio_to_irq(gpio); -} - static inline int irq_to_gpio(unsigned int irq) { return -ENOSYS; } +#else + +#define __ARM_GPIOLIB_COMPLEX + #endif /* CONFIG_GPIOLIB */ #endif /* __ASM_ARCH_GPIO_H */ diff --git a/arch/arm/mach-tegra/board-harmony-pcie.c b/arch/arm/mach-tegra/board-harmony-pcie.c index 9c27b95b8d86..6db7d699ef1c 100644 --- a/arch/arm/mach-tegra/board-harmony-pcie.c +++ b/arch/arm/mach-tegra/board-harmony-pcie.c @@ -24,12 +24,10 @@ #include <mach/pinmux.h> #include "board.h" +#include "board-harmony.h" #ifdef CONFIG_TEGRA_PCI -/* GPIO 3 of the PMIC */ -#define EN_VDD_1V05_GPIO (TEGRA_NR_GPIOS + 2) - static int __init harmony_pcie_init(void) { struct regulator *regulator = NULL; @@ -38,11 +36,11 @@ static int __init harmony_pcie_init(void) if (!machine_is_harmony()) return 0; - err = gpio_request(EN_VDD_1V05_GPIO, "EN_VDD_1V05"); + err = gpio_request(TEGRA_GPIO_EN_VDD_1V05_GPIO, "EN_VDD_1V05"); if (err) return err; - gpio_direction_output(EN_VDD_1V05_GPIO, 1); + gpio_direction_output(TEGRA_GPIO_EN_VDD_1V05_GPIO, 1); regulator = regulator_get(NULL, "pex_clk"); if (IS_ERR_OR_NULL(regulator)) @@ -68,7 +66,7 @@ err_pcie: regulator_disable(regulator); regulator_put(regulator); err_reg: - gpio_free(EN_VDD_1V05_GPIO); + gpio_free(TEGRA_GPIO_EN_VDD_1V05_GPIO); return err; } diff --git a/arch/arm/mach-tegra/board-harmony.h b/arch/arm/mach-tegra/board-harmony.h index d85142edaf6b..139d96c93843 100644 --- a/arch/arm/mach-tegra/board-harmony.h +++ b/arch/arm/mach-tegra/board-harmony.h @@ -17,6 +17,8 @@ #ifndef _MACH_TEGRA_BOARD_HARMONY_H #define _MACH_TEGRA_BOARD_HARMONY_H +#include <mach/gpio-tegra.h> + #define HARMONY_GPIO_TPS6586X(_x_) (TEGRA_NR_GPIOS + (_x_)) #define HARMONY_GPIO_WM8903(_x_) (HARMONY_GPIO_TPS6586X(4) + (_x_)) @@ -31,6 +33,7 @@ #define TEGRA_GPIO_HP_DET TEGRA_GPIO_PW2 #define TEGRA_GPIO_INT_MIC_EN TEGRA_GPIO_PX0 #define TEGRA_GPIO_EXT_MIC_EN TEGRA_GPIO_PX1 +#define TEGRA_GPIO_EN_VDD_1V05_GPIO HARMONY_GPIO_TPS6586X(2) void harmony_pinmux_init(void); int harmony_regulator_init(void); diff --git a/arch/arm/mach-tegra/board-paz00.h b/arch/arm/mach-tegra/board-paz00.h index d4ff39ddaeb3..42ce8639b90c 100644 --- a/arch/arm/mach-tegra/board-paz00.h +++ b/arch/arm/mach-tegra/board-paz00.h @@ -17,6 +17,8 @@ #ifndef _MACH_TEGRA_BOARD_PAZ00_H #define _MACH_TEGRA_BOARD_PAZ00_H +#include <mach/gpio-tegra.h> + #define TEGRA_GPIO_SD1_CD TEGRA_GPIO_PV5 #define TEGRA_GPIO_SD1_WP TEGRA_GPIO_PH1 #define TEGRA_GPIO_SD1_POWER TEGRA_GPIO_PT3 diff --git a/arch/arm/mach-tegra/board-seaboard.h b/arch/arm/mach-tegra/board-seaboard.h index d8415e1a8434..15b6c57361be 100644 --- a/arch/arm/mach-tegra/board-seaboard.h +++ b/arch/arm/mach-tegra/board-seaboard.h @@ -17,6 +17,8 @@ #ifndef _MACH_TEGRA_BOARD_SEABOARD_H #define _MACH_TEGRA_BOARD_SEABOARD_H +#include <mach/gpio-tegra.h> + #define TEGRA_GPIO_SD2_CD TEGRA_GPIO_PI5 #define TEGRA_GPIO_SD2_WP TEGRA_GPIO_PH1 #define TEGRA_GPIO_SD2_POWER TEGRA_GPIO_PI6 diff --git a/arch/arm/mach-tegra/board-trimslice-pinmux.c b/arch/arm/mach-tegra/board-trimslice-pinmux.c index 47c596cdbf32..bcb1916e68b9 100644 --- a/arch/arm/mach-tegra/board-trimslice-pinmux.c +++ b/arch/arm/mach-tegra/board-trimslice-pinmux.c @@ -13,12 +13,11 @@ * GNU General Public License for more details. * */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <mach/pinmux.h> -#include <mach/gpio.h> #include "gpio-names.h" #include "board-trimslice.h" diff --git a/arch/arm/mach-tegra/board-trimslice.h b/arch/arm/mach-tegra/board-trimslice.h index 7a7dee86b4da..50f128d87779 100644 --- a/arch/arm/mach-tegra/board-trimslice.h +++ b/arch/arm/mach-tegra/board-trimslice.h @@ -17,6 +17,8 @@ #ifndef _MACH_TEGRA_BOARD_TRIMSLICE_H #define _MACH_TEGRA_BOARD_TRIMSLICE_H +#include <mach/gpio-tegra.h> + #define TRIMSLICE_GPIO_SD4_CD TEGRA_GPIO_PP1 /* mmc4 cd */ #define TRIMSLICE_GPIO_SD4_WP TEGRA_GPIO_PP2 /* mmc4 wp */ diff --git a/arch/arm/mach-tegra/include/mach/gpio-tegra.h b/arch/arm/mach-tegra/include/mach/gpio-tegra.h new file mode 100644 index 000000000000..87d37fdf5084 --- /dev/null +++ b/arch/arm/mach-tegra/include/mach/gpio-tegra.h @@ -0,0 +1,39 @@ +/* + * arch/arm/mach-tegra/include/mach/gpio.h + * + * Copyright (C) 2010 Google, Inc. + * + * Author: + * Erik Gilling <konkers@google.com> + * + * This software is licensed under the terms of the GNU General Public + * License version 2, as published by the Free Software Foundation, and + * may be copied, distributed, and modified under those terms. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#ifndef __MACH_TEGRA_GPIO_TEGRA_H +#define __MACH_TEGRA_GPIO_TEGRA_H + +#include <linux/types.h> +#include <mach/irqs.h> + +#define TEGRA_NR_GPIOS INT_GPIO_NR + +#define TEGRA_GPIO_TO_IRQ(gpio) (INT_GPIO_BASE + (gpio)) + +struct tegra_gpio_table { + int gpio; /* GPIO number */ + bool enable; /* Enable for GPIO at init? */ +}; + +void tegra_gpio_config(struct tegra_gpio_table *table, int num); +void tegra_gpio_enable(int gpio); +void tegra_gpio_disable(int gpio); + +#endif diff --git a/arch/arm/mach-tegra/include/mach/gpio.h b/arch/arm/mach-tegra/include/mach/gpio.h index 196f114dc241..e69de29bb2d1 100644 --- a/arch/arm/mach-tegra/include/mach/gpio.h +++ b/arch/arm/mach-tegra/include/mach/gpio.h @@ -1,60 +0,0 @@ -/* - * arch/arm/mach-tegra/include/mach/gpio.h - * - * Copyright (C) 2010 Google, Inc. - * - * Author: - * Erik Gilling <konkers@google.com> - * - * This software is licensed under the terms of the GNU General Public - * License version 2, as published by the Free Software Foundation, and - * may be copied, distributed, and modified under those terms. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - */ - -#ifndef __MACH_TEGRA_GPIO_H -#define __MACH_TEGRA_GPIO_H - -#include <linux/init.h> -#include <mach/irqs.h> - -#define TEGRA_NR_GPIOS INT_GPIO_NR - -#include <asm-generic/gpio.h> - -#define gpio_get_value __gpio_get_value -#define gpio_set_value __gpio_set_value -#define gpio_cansleep __gpio_cansleep - -#define TEGRA_GPIO_TO_IRQ(gpio) (INT_GPIO_BASE + (gpio)) -#define TEGRA_IRQ_TO_GPIO(irq) ((irq) - INT_GPIO_BASE) - -static inline int gpio_to_irq(unsigned int gpio) -{ - if (gpio < TEGRA_NR_GPIOS) - return INT_GPIO_BASE + gpio; - return -EINVAL; -} - -static inline int irq_to_gpio(unsigned int irq) -{ - if ((irq >= INT_GPIO_BASE) && (irq < INT_GPIO_BASE + INT_GPIO_NR)) - return irq - INT_GPIO_BASE; - return -EINVAL; -} - -struct tegra_gpio_table { - int gpio; /* GPIO number */ - bool enable; /* Enable for GPIO at init? */ -}; - -void tegra_gpio_config(struct tegra_gpio_table *table, int num); -void tegra_gpio_enable(int gpio); -void tegra_gpio_disable(int gpio); - -#endif diff --git a/arch/arm/mach-tegra/usb_phy.c b/arch/arm/mach-tegra/usb_phy.c index 88081bb3ec52..37576a721aeb 100644 --- a/arch/arm/mach-tegra/usb_phy.c +++ b/arch/arm/mach-tegra/usb_phy.c @@ -28,6 +28,7 @@ #include <linux/usb/otg.h> #include <linux/usb/ulpi.h> #include <asm/mach-types.h> +#include <mach/gpio-tegra.h> #include <mach/usb_phy.h> #include <mach/iomap.h> diff --git a/arch/arm/mach-u300/Kconfig b/arch/arm/mach-u300/Kconfig index 32a7b0f7e9f7..7b5c229dc7ea 100644 --- a/arch/arm/mach-u300/Kconfig +++ b/arch/arm/mach-u300/Kconfig @@ -6,6 +6,7 @@ comment "ST-Ericsson Mobile Platform Products" config MACH_U300 bool "U300" + select GPIO_U300 comment "ST-Ericsson U300/U330/U335/U365 Feature Selections" diff --git a/arch/arm/mach-u300/core.c b/arch/arm/mach-u300/core.c index 376b6dfdfae9..22c5ab79a74c 100644 --- a/arch/arm/mach-u300/core.c +++ b/arch/arm/mach-u300/core.c @@ -38,6 +38,7 @@ #include <mach/hardware.h> #include <mach/syscon.h> #include <mach/dma_channels.h> +#include <mach/gpio-u300.h> #include "clock.h" #include "mmc.h" @@ -242,7 +243,7 @@ static struct resource gpio_resources[] = { .end = IRQ_U300_GPIO_PORT2, .flags = IORESOURCE_IRQ, }, -#ifdef U300_COH901571_3 +#if defined(CONFIG_MACH_U300_BS365) || defined(CONFIG_MACH_U300_BS335) { .name = "gpio3", .start = IRQ_U300_GPIO_PORT3, @@ -255,6 +256,7 @@ static struct resource gpio_resources[] = { .end = IRQ_U300_GPIO_PORT4, .flags = IORESOURCE_IRQ, }, +#endif #ifdef CONFIG_MACH_U300_BS335 { .name = "gpio5", @@ -269,7 +271,6 @@ static struct resource gpio_resources[] = { .flags = IORESOURCE_IRQ, }, #endif /* CONFIG_MACH_U300_BS335 */ -#endif /* U300_COH901571_3 */ }; static struct resource keypad_resources[] = { @@ -1559,11 +1560,35 @@ static struct platform_device i2c1_device = { .resource = i2c1_resources, }; +/* + * The different variants have a few different versions of the + * GPIO block, with different number of ports. + */ +static struct u300_gpio_platform u300_gpio_plat = { +#if defined(CONFIG_MACH_U300_BS2X) || defined(CONFIG_MACH_U300_BS330) + .variant = U300_GPIO_COH901335, + .ports = 3, +#endif +#ifdef CONFIG_MACH_U300_BS335 + .variant = U300_GPIO_COH901571_3_BS335, + .ports = 7, +#endif +#ifdef CONFIG_MACH_U300_BS365 + .variant = U300_GPIO_COH901571_3_BS365, + .ports = 5, +#endif + .gpio_base = 0, + .gpio_irq_base = IRQ_U300_GPIO_BASE, +}; + static struct platform_device gpio_device = { .name = "u300-gpio", .id = -1, .num_resources = ARRAY_SIZE(gpio_resources), .resource = gpio_resources, + .dev = { + .platform_data = &u300_gpio_plat, + }, }; static struct platform_device keypad_device = { @@ -1669,7 +1694,7 @@ void __init u300_init_irq(void) BUG_ON(IS_ERR(clk)); clk_enable(clk); - for (i = 0; i < NR_IRQS; i++) + for (i = 0; i < U300_VIC_IRQS_END; i++) set_bit(i, (unsigned long *) &mask[0]); vic_init((void __iomem *) U300_INTCON0_VBASE, 0, mask[0], mask[0]); vic_init((void __iomem *) U300_INTCON1_VBASE, 32, mask[1], mask[1]); diff --git a/arch/arm/mach-u300/include/mach/gpio-u300.h b/arch/arm/mach-u300/include/mach/gpio-u300.h new file mode 100644 index 000000000000..0c2b2021951a --- /dev/null +++ b/arch/arm/mach-u300/include/mach/gpio-u300.h @@ -0,0 +1,150 @@ +/* + * Copyright (C) 2007-2011 ST-Ericsson AB + * License terms: GNU General Public License (GPL) version 2 + * GPIO block resgister definitions and inline macros for + * U300 GPIO COH 901 335 or COH 901 571/3 + * Author: Linus Walleij <linus.walleij@stericsson.com> + */ + +#ifndef __MACH_U300_GPIO_U300_H +#define __MACH_U300_GPIO_U300_H + +/* + * Individual pin assignments for the B26/S26. Notice that the + * actual usage of these pins depends on the PAD MUX settings, that + * is why the same number can potentially appear several times. + * In the reference design each pin is only used for one purpose. + * These were determined by inspecting the B26/S26 schematic: + * 2/1911-ROA 128 1603 + */ +#ifdef CONFIG_MACH_U300_BS2X +#define U300_GPIO_PIN_UART_RX 0 +#define U300_GPIO_PIN_UART_TX 1 +#define U300_GPIO_PIN_GPIO02 2 /* Unrouted */ +#define U300_GPIO_PIN_GPIO03 3 /* Unrouted */ +#define U300_GPIO_PIN_CAM_SLEEP 4 +#define U300_GPIO_PIN_CAM_REG_EN 5 +#define U300_GPIO_PIN_GPIO06 6 /* Unrouted */ +#define U300_GPIO_PIN_GPIO07 7 /* Unrouted */ + +#define U300_GPIO_PIN_GPIO08 8 /* Service point SP2321 */ +#define U300_GPIO_PIN_GPIO09 9 /* Service point SP2322 */ +#define U300_GPIO_PIN_PHFSENSE 10 /* Headphone jack sensing */ +#define U300_GPIO_PIN_MMC_CLKRET 11 /* Clock return from MMC/SD card */ +#define U300_GPIO_PIN_MMC_CD 12 /* MMC Card insertion detection */ +#define U300_GPIO_PIN_FLIPSENSE 13 /* Mechanical flip sensing */ +#define U300_GPIO_PIN_GPIO14 14 /* DSP JTAG Port RTCK */ +#define U300_GPIO_PIN_GPIO15 15 /* Unrouted */ + +#define U300_GPIO_PIN_GPIO16 16 /* Unrouted */ +#define U300_GPIO_PIN_GPIO17 17 /* Unrouted */ +#define U300_GPIO_PIN_GPIO18 18 /* Unrouted */ +#define U300_GPIO_PIN_GPIO19 19 /* Unrouted */ +#define U300_GPIO_PIN_GPIO20 20 /* Unrouted */ +#define U300_GPIO_PIN_GPIO21 21 /* Unrouted */ +#define U300_GPIO_PIN_GPIO22 22 /* Unrouted */ +#define U300_GPIO_PIN_GPIO23 23 /* Unrouted */ +#endif + +/* + * Individual pin assignments for the B330/S330 and B365/S365. + * Notice that the actual usage of these pins depends on the + * PAD MUX settings, that is why the same number can potentially + * appear several times. In the reference design each pin is only + * used for one purpose. These were determined by inspecting the + * S365 schematic. + */ +#if defined(CONFIG_MACH_U300_BS330) || defined(CONFIG_MACH_U300_BS365) || \ + defined(CONFIG_MACH_U300_BS335) +#define U300_GPIO_PIN_UART_RX 0 +#define U300_GPIO_PIN_UART_TX 1 +#define U300_GPIO_PIN_UART_CTS 2 +#define U300_GPIO_PIN_UART_RTS 3 +#define U300_GPIO_PIN_CAM_MAIN_STANDBY 4 /* Camera MAIN standby */ +#define U300_GPIO_PIN_GPIO05 5 /* Unrouted */ +#define U300_GPIO_PIN_MS_CD 6 /* Memory Stick Card insertion */ +#define U300_GPIO_PIN_GPIO07 7 /* Test point TP2430 */ + +#define U300_GPIO_PIN_GPIO08 8 /* Test point TP2437 */ +#define U300_GPIO_PIN_GPIO09 9 /* Test point TP2431 */ +#define U300_GPIO_PIN_GPIO10 10 /* Test point TP2432 */ +#define U300_GPIO_PIN_MMC_CLKRET 11 /* Clock return from MMC/SD card */ +#define U300_GPIO_PIN_MMC_CD 12 /* MMC Card insertion detection */ +#define U300_GPIO_PIN_CAM_SUB_STANDBY 13 /* Camera SUB standby */ +#define U300_GPIO_PIN_GPIO14 14 /* Test point TP2436 */ +#define U300_GPIO_PIN_GPIO15 15 /* Unrouted */ + +#define U300_GPIO_PIN_GPIO16 16 /* Test point TP2438 */ +#define U300_GPIO_PIN_PHFSENSE 17 /* Headphone jack sensing */ +#define U300_GPIO_PIN_GPIO18 18 /* Test point TP2439 */ +#define U300_GPIO_PIN_GPIO19 19 /* Routed somewhere */ +#define U300_GPIO_PIN_GPIO20 20 /* Unrouted */ +#define U300_GPIO_PIN_GPIO21 21 /* Unrouted */ +#define U300_GPIO_PIN_GPIO22 22 /* Unrouted */ +#define U300_GPIO_PIN_GPIO23 23 /* Unrouted */ + +#define U300_GPIO_PIN_GPIO24 24 /* Unrouted */ +#define U300_GPIO_PIN_GPIO25 25 /* Unrouted */ +#define U300_GPIO_PIN_GPIO26 26 /* Unrouted */ +#define U300_GPIO_PIN_GPIO27 27 /* Unrouted */ +#define U300_GPIO_PIN_GPIO28 28 /* Unrouted */ +#define U300_GPIO_PIN_GPIO29 29 /* Unrouted */ +#define U300_GPIO_PIN_GPIO30 30 /* Unrouted */ +#define U300_GPIO_PIN_GPIO31 31 /* Unrouted */ + +#define U300_GPIO_PIN_GPIO32 32 /* Unrouted */ +#define U300_GPIO_PIN_GPIO33 33 /* Unrouted */ +#define U300_GPIO_PIN_GPIO34 34 /* Unrouted */ +#define U300_GPIO_PIN_GPIO35 35 /* Unrouted */ +#define U300_GPIO_PIN_GPIO36 36 /* Unrouted */ +#define U300_GPIO_PIN_GPIO37 37 /* Unrouted */ +#define U300_GPIO_PIN_GPIO38 38 /* Unrouted */ +#define U300_GPIO_PIN_GPIO39 39 /* Unrouted */ + +#ifdef CONFIG_MACH_U300_BS335 + +#define U300_GPIO_PIN_GPIO40 40 /* Unrouted */ +#define U300_GPIO_PIN_GPIO41 41 /* Unrouted */ +#define U300_GPIO_PIN_GPIO42 42 /* Unrouted */ +#define U300_GPIO_PIN_GPIO43 43 /* Unrouted */ +#define U300_GPIO_PIN_GPIO44 44 /* Unrouted */ +#define U300_GPIO_PIN_GPIO45 45 /* Unrouted */ +#define U300_GPIO_PIN_GPIO46 46 /* Unrouted */ +#define U300_GPIO_PIN_GPIO47 47 /* Unrouted */ + +#define U300_GPIO_PIN_GPIO48 48 /* Unrouted */ +#define U300_GPIO_PIN_GPIO49 49 /* Unrouted */ +#define U300_GPIO_PIN_GPIO50 50 /* Unrouted */ +#define U300_GPIO_PIN_GPIO51 51 /* Unrouted */ +#define U300_GPIO_PIN_GPIO52 52 /* Unrouted */ +#define U300_GPIO_PIN_GPIO53 53 /* Unrouted */ +#define U300_GPIO_PIN_GPIO54 54 /* Unrouted */ +#define U300_GPIO_PIN_GPIO55 55 /* Unrouted */ +#endif + +#endif + +/** + * enum u300_gpio_variant - the type of U300 GPIO employed + */ +enum u300_gpio_variant { + U300_GPIO_COH901335, + U300_GPIO_COH901571_3_BS335, + U300_GPIO_COH901571_3_BS365, +}; + +/** + * struct u300_gpio_platform - U300 GPIO platform data + * @variant: IP block variant + * @ports: number of GPIO block ports + * @gpio_base: first GPIO number for this block (use a free range) + * @gpio_irq_base: first GPIO IRQ number for this block (use a free range) + */ +struct u300_gpio_platform { + enum u300_gpio_variant variant; + u8 ports; + int gpio_base; + int gpio_irq_base; +}; + +#endif /* __MACH_U300_GPIO_U300_H */ diff --git a/arch/arm/mach-u300/include/mach/gpio.h b/arch/arm/mach-u300/include/mach/gpio.h index d5a71abcbaea..e69de29bb2d1 100644 --- a/arch/arm/mach-u300/include/mach/gpio.h +++ b/arch/arm/mach-u300/include/mach/gpio.h @@ -1,294 +0,0 @@ -/* - * - * arch/arm/mach-u300/include/mach/gpio.h - * - * - * Copyright (C) 2007-2009 ST-Ericsson AB - * License terms: GNU General Public License (GPL) version 2 - * GPIO block resgister definitions and inline macros for - * U300 GPIO COH 901 335 or COH 901 571/3 - * Author: Linus Walleij <linus.walleij@stericsson.com> - */ - -#ifndef __MACH_U300_GPIO_H -#define __MACH_U300_GPIO_H - -#include <linux/kernel.h> -#include <linux/io.h> -#include <mach/hardware.h> -#include <asm/irq.h> - -/* Switch type depending on platform/chip variant */ -#if defined(CONFIG_MACH_U300_BS2X) || defined(CONFIG_MACH_U300_BS330) -#define U300_COH901335 -#endif -#if defined(CONFIG_MACH_U300_BS365) || defined(CONFIG_MACH_U300_BS335) -#define U300_COH901571_3 -#endif - -/* Get base address for regs here */ -#include "u300-regs.h" -/* IRQ numbers */ -#include "irqs.h" - -/* - * This is the GPIO block definitions. GPIO (General Purpose I/O) can be - * used for anything, and often is. The event/enable etc figures are for - * the lowermost pin (pin 0 on each port), shift this left to match your - * pin if you're gonna use these values. - */ -#ifdef U300_COH901335 -#define U300_GPIO_PORTX_SPACING (0x1C) -/* Port X Pin Data Register 32bit, this is both input and output (R/W) */ -#define U300_GPIO_PXPDIR (0x00) -#define U300_GPIO_PXPDOR (0x00) -/* Port X Pin Config Register 32bit (R/W) */ -#define U300_GPIO_PXPCR (0x04) -#define U300_GPIO_PXPCR_ALL_PINS_MODE_MASK (0x0000FFFFUL) -#define U300_GPIO_PXPCR_PIN_MODE_MASK (0x00000003UL) -#define U300_GPIO_PXPCR_PIN_MODE_SHIFT (0x00000002UL) -#define U300_GPIO_PXPCR_PIN_MODE_INPUT (0x00000000UL) -#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL (0x00000001UL) -#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN (0x00000002UL) -#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE (0x00000003UL) -/* Port X Interrupt Event Register 32bit (R/W) */ -#define U300_GPIO_PXIEV (0x08) -#define U300_GPIO_PXIEV_ALL_IRQ_EVENT_MASK (0x000000FFUL) -#define U300_GPIO_PXIEV_IRQ_EVENT (0x00000001UL) -/* Port X Interrupt Enable Register 32bit (R/W) */ -#define U300_GPIO_PXIEN (0x0C) -#define U300_GPIO_PXIEN_ALL_IRQ_ENABLE_MASK (0x000000FFUL) -#define U300_GPIO_PXIEN_IRQ_ENABLE (0x00000001UL) -/* Port X Interrupt Force Register 32bit (R/W) */ -#define U300_GPIO_PXIFR (0x10) -#define U300_GPIO_PXIFR_ALL_IRQ_FORCE_MASK (0x000000FFUL) -#define U300_GPIO_PXIFR_IRQ_FORCE (0x00000001UL) -/* Port X Interrupt Config Register 32bit (R/W) */ -#define U300_GPIO_PXICR (0x14) -#define U300_GPIO_PXICR_ALL_IRQ_CONFIG_MASK (0x000000FFUL) -#define U300_GPIO_PXICR_IRQ_CONFIG_MASK (0x00000001UL) -#define U300_GPIO_PXICR_IRQ_CONFIG_FALLING_EDGE (0x00000000UL) -#define U300_GPIO_PXICR_IRQ_CONFIG_RISING_EDGE (0x00000001UL) -/* Port X Pull-up Enable Register 32bit (R/W) */ -#define U300_GPIO_PXPER (0x18) -#define U300_GPIO_PXPER_ALL_PULL_UP_DISABLE_MASK (0x000000FFUL) -#define U300_GPIO_PXPER_PULL_UP_DISABLE (0x00000001UL) -/* Control Register 32bit (R/W) */ -#define U300_GPIO_CR (0x54) -#define U300_GPIO_CR_BLOCK_CLOCK_ENABLE (0x00000001UL) -/* three ports of 8 bits each = GPIO pins 0..23 */ -#define U300_GPIO_NUM_PORTS 3 -#define U300_GPIO_PINS_PER_PORT 8 -#define U300_GPIO_MAX (U300_GPIO_PINS_PER_PORT * U300_GPIO_NUM_PORTS - 1) -#endif - -#ifdef U300_COH901571_3 -/* - * Control Register 32bit (R/W) - * bit 15-9 (mask 0x0000FE00) contains the number of cores. 8*cores - * gives the number of GPIO pins. - * bit 8-2 (mask 0x000001FC) contains the core version ID. - */ -#define U300_GPIO_CR (0x00) -#define U300_GPIO_CR_SYNC_SEL_ENABLE (0x00000002UL) -#define U300_GPIO_CR_BLOCK_CLKRQ_ENABLE (0x00000001UL) -#define U300_GPIO_PORTX_SPACING (0x30) -/* Port X Pin Data INPUT Register 32bit (R/W) */ -#define U300_GPIO_PXPDIR (0x04) -/* Port X Pin Data OUTPUT Register 32bit (R/W) */ -#define U300_GPIO_PXPDOR (0x08) -/* Port X Pin Config Register 32bit (R/W) */ -#define U300_GPIO_PXPCR (0x0C) -#define U300_GPIO_PXPCR_ALL_PINS_MODE_MASK (0x0000FFFFUL) -#define U300_GPIO_PXPCR_PIN_MODE_MASK (0x00000003UL) -#define U300_GPIO_PXPCR_PIN_MODE_SHIFT (0x00000002UL) -#define U300_GPIO_PXPCR_PIN_MODE_INPUT (0x00000000UL) -#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL (0x00000001UL) -#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN (0x00000002UL) -#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE (0x00000003UL) -/* Port X Pull-up Enable Register 32bit (R/W) */ -#define U300_GPIO_PXPER (0x10) -#define U300_GPIO_PXPER_ALL_PULL_UP_DISABLE_MASK (0x000000FFUL) -#define U300_GPIO_PXPER_PULL_UP_DISABLE (0x00000001UL) -/* Port X Interrupt Event Register 32bit (R/W) */ -#define U300_GPIO_PXIEV (0x14) -#define U300_GPIO_PXIEV_ALL_IRQ_EVENT_MASK (0x000000FFUL) -#define U300_GPIO_PXIEV_IRQ_EVENT (0x00000001UL) -/* Port X Interrupt Enable Register 32bit (R/W) */ -#define U300_GPIO_PXIEN (0x18) -#define U300_GPIO_PXIEN_ALL_IRQ_ENABLE_MASK (0x000000FFUL) -#define U300_GPIO_PXIEN_IRQ_ENABLE (0x00000001UL) -/* Port X Interrupt Force Register 32bit (R/W) */ -#define U300_GPIO_PXIFR (0x1C) -#define U300_GPIO_PXIFR_ALL_IRQ_FORCE_MASK (0x000000FFUL) -#define U300_GPIO_PXIFR_IRQ_FORCE (0x00000001UL) -/* Port X Interrupt Config Register 32bit (R/W) */ -#define U300_GPIO_PXICR (0x20) -#define U300_GPIO_PXICR_ALL_IRQ_CONFIG_MASK (0x000000FFUL) -#define U300_GPIO_PXICR_IRQ_CONFIG_MASK (0x00000001UL) -#define U300_GPIO_PXICR_IRQ_CONFIG_FALLING_EDGE (0x00000000UL) -#define U300_GPIO_PXICR_IRQ_CONFIG_RISING_EDGE (0x00000001UL) -#ifdef CONFIG_MACH_U300_BS335 -/* seven ports of 8 bits each = GPIO pins 0..55 */ -#define U300_GPIO_NUM_PORTS 7 -#else -/* five ports of 8 bits each = GPIO pins 0..39 */ -#define U300_GPIO_NUM_PORTS 5 -#endif -#define U300_GPIO_PINS_PER_PORT 8 -#define U300_GPIO_MAX (U300_GPIO_PINS_PER_PORT * U300_GPIO_NUM_PORTS - 1) -#endif - -/* - * Individual pin assignments for the B26/S26. Notice that the - * actual usage of these pins depends on the PAD MUX settings, that - * is why the same number can potentially appear several times. - * In the reference design each pin is only used for one purpose. - * These were determined by inspecting the B26/S26 schematic: - * 2/1911-ROA 128 1603 - */ -#ifdef CONFIG_MACH_U300_BS2X -#define U300_GPIO_PIN_UART_RX 0 -#define U300_GPIO_PIN_UART_TX 1 -#define U300_GPIO_PIN_GPIO02 2 /* Unrouted */ -#define U300_GPIO_PIN_GPIO03 3 /* Unrouted */ -#define U300_GPIO_PIN_CAM_SLEEP 4 -#define U300_GPIO_PIN_CAM_REG_EN 5 -#define U300_GPIO_PIN_GPIO06 6 /* Unrouted */ -#define U300_GPIO_PIN_GPIO07 7 /* Unrouted */ - -#define U300_GPIO_PIN_GPIO08 8 /* Service point SP2321 */ -#define U300_GPIO_PIN_GPIO09 9 /* Service point SP2322 */ -#define U300_GPIO_PIN_PHFSENSE 10 /* Headphone jack sensing */ -#define U300_GPIO_PIN_MMC_CLKRET 11 /* Clock return from MMC/SD card */ -#define U300_GPIO_PIN_MMC_CD 12 /* MMC Card insertion detection */ -#define U300_GPIO_PIN_FLIPSENSE 13 /* Mechanical flip sensing */ -#define U300_GPIO_PIN_GPIO14 14 /* DSP JTAG Port RTCK */ -#define U300_GPIO_PIN_GPIO15 15 /* Unrouted */ - -#define U300_GPIO_PIN_GPIO16 16 /* Unrouted */ -#define U300_GPIO_PIN_GPIO17 17 /* Unrouted */ -#define U300_GPIO_PIN_GPIO18 18 /* Unrouted */ -#define U300_GPIO_PIN_GPIO19 19 /* Unrouted */ -#define U300_GPIO_PIN_GPIO20 20 /* Unrouted */ -#define U300_GPIO_PIN_GPIO21 21 /* Unrouted */ -#define U300_GPIO_PIN_GPIO22 22 /* Unrouted */ -#define U300_GPIO_PIN_GPIO23 23 /* Unrouted */ -#endif - -/* - * Individual pin assignments for the B330/S330 and B365/S365. - * Notice that the actual usage of these pins depends on the - * PAD MUX settings, that is why the same number can potentially - * appear several times. In the reference design each pin is only - * used for one purpose. These were determined by inspecting the - * S365 schematic. - */ -#if defined(CONFIG_MACH_U300_BS330) || defined(CONFIG_MACH_U300_BS365) || \ - defined(CONFIG_MACH_U300_BS335) -#define U300_GPIO_PIN_UART_RX 0 -#define U300_GPIO_PIN_UART_TX 1 -#define U300_GPIO_PIN_UART_CTS 2 -#define U300_GPIO_PIN_UART_RTS 3 -#define U300_GPIO_PIN_CAM_MAIN_STANDBY 4 /* Camera MAIN standby */ -#define U300_GPIO_PIN_GPIO05 5 /* Unrouted */ -#define U300_GPIO_PIN_MS_CD 6 /* Memory Stick Card insertion */ -#define U300_GPIO_PIN_GPIO07 7 /* Test point TP2430 */ - -#define U300_GPIO_PIN_GPIO08 8 /* Test point TP2437 */ -#define U300_GPIO_PIN_GPIO09 9 /* Test point TP2431 */ -#define U300_GPIO_PIN_GPIO10 10 /* Test point TP2432 */ -#define U300_GPIO_PIN_MMC_CLKRET 11 /* Clock return from MMC/SD card */ -#define U300_GPIO_PIN_MMC_CD 12 /* MMC Card insertion detection */ -#define U300_GPIO_PIN_CAM_SUB_STANDBY 13 /* Camera SUB standby */ -#define U300_GPIO_PIN_GPIO14 14 /* Test point TP2436 */ -#define U300_GPIO_PIN_GPIO15 15 /* Unrouted */ - -#define U300_GPIO_PIN_GPIO16 16 /* Test point TP2438 */ -#define U300_GPIO_PIN_PHFSENSE 17 /* Headphone jack sensing */ -#define U300_GPIO_PIN_GPIO18 18 /* Test point TP2439 */ -#define U300_GPIO_PIN_GPIO19 19 /* Routed somewhere */ -#define U300_GPIO_PIN_GPIO20 20 /* Unrouted */ -#define U300_GPIO_PIN_GPIO21 21 /* Unrouted */ -#define U300_GPIO_PIN_GPIO22 22 /* Unrouted */ -#define U300_GPIO_PIN_GPIO23 23 /* Unrouted */ - -#define U300_GPIO_PIN_GPIO24 24 /* Unrouted */ -#define U300_GPIO_PIN_GPIO25 25 /* Unrouted */ -#define U300_GPIO_PIN_GPIO26 26 /* Unrouted */ -#define U300_GPIO_PIN_GPIO27 27 /* Unrouted */ -#define U300_GPIO_PIN_GPIO28 28 /* Unrouted */ -#define U300_GPIO_PIN_GPIO29 29 /* Unrouted */ -#define U300_GPIO_PIN_GPIO30 30 /* Unrouted */ -#define U300_GPIO_PIN_GPIO31 31 /* Unrouted */ - -#define U300_GPIO_PIN_GPIO32 32 /* Unrouted */ -#define U300_GPIO_PIN_GPIO33 33 /* Unrouted */ -#define U300_GPIO_PIN_GPIO34 34 /* Unrouted */ -#define U300_GPIO_PIN_GPIO35 35 /* Unrouted */ -#define U300_GPIO_PIN_GPIO36 36 /* Unrouted */ -#define U300_GPIO_PIN_GPIO37 37 /* Unrouted */ -#define U300_GPIO_PIN_GPIO38 38 /* Unrouted */ -#define U300_GPIO_PIN_GPIO39 39 /* Unrouted */ - -#ifdef CONFIG_MACH_U300_BS335 - -#define U300_GPIO_PIN_GPIO40 40 /* Unrouted */ -#define U300_GPIO_PIN_GPIO41 41 /* Unrouted */ -#define U300_GPIO_PIN_GPIO42 42 /* Unrouted */ -#define U300_GPIO_PIN_GPIO43 43 /* Unrouted */ -#define U300_GPIO_PIN_GPIO44 44 /* Unrouted */ -#define U300_GPIO_PIN_GPIO45 45 /* Unrouted */ -#define U300_GPIO_PIN_GPIO46 46 /* Unrouted */ -#define U300_GPIO_PIN_GPIO47 47 /* Unrouted */ - -#define U300_GPIO_PIN_GPIO48 48 /* Unrouted */ -#define U300_GPIO_PIN_GPIO49 49 /* Unrouted */ -#define U300_GPIO_PIN_GPIO50 50 /* Unrouted */ -#define U300_GPIO_PIN_GPIO51 51 /* Unrouted */ -#define U300_GPIO_PIN_GPIO52 52 /* Unrouted */ -#define U300_GPIO_PIN_GPIO53 53 /* Unrouted */ -#define U300_GPIO_PIN_GPIO54 54 /* Unrouted */ -#define U300_GPIO_PIN_GPIO55 55 /* Unrouted */ -#endif - -#endif - -/* translates a pin number to a port number */ -#define PIN_TO_PORT(val) (val >> 3) - -/* These can be found in arch/arm/mach-u300/gpio.c */ -extern int gpio_is_valid(int number); -extern int gpio_request(unsigned gpio, const char *label); -extern void gpio_free(unsigned gpio); -extern int gpio_direction_input(unsigned gpio); -extern int gpio_direction_output(unsigned gpio, int value); -extern int gpio_register_callback(unsigned gpio, - int (*func)(void *arg), - void *); -extern int gpio_unregister_callback(unsigned gpio); -extern void enable_irq_on_gpio_pin(unsigned gpio, int edge); -extern void disable_irq_on_gpio_pin(unsigned gpio); -extern void gpio_pullup(unsigned gpio, int value); -extern int gpio_get_value(unsigned gpio); -extern void gpio_set_value(unsigned gpio, int value); - -#define gpio_get_value_cansleep gpio_get_value -#define gpio_set_value_cansleep gpio_set_value - -/* wrappers to sleep-enable the previous two functions */ -static inline unsigned gpio_to_irq(unsigned gpio) -{ - return PIN_TO_PORT(gpio) + IRQ_U300_GPIO_PORT0; -} - -static inline unsigned irq_to_gpio(unsigned irq) -{ - /* - * FIXME: This is no 1-1 mapping at all, it points to the - * whole block of 8 pins. - */ - return (irq - IRQ_U300_GPIO_PORT0) << 3; -} - -#endif diff --git a/arch/arm/mach-u300/include/mach/irqs.h b/arch/arm/mach-u300/include/mach/irqs.h index 09b1b28fa8fd..d270fea32926 100644 --- a/arch/arm/mach-u300/include/mach/irqs.h +++ b/arch/arm/mach-u300/include/mach/irqs.h @@ -72,7 +72,7 @@ /* DB3150 and DB3200 have only 45 IRQs */ #if defined(CONFIG_MACH_U300_BS2X) || defined(CONFIG_MACH_U300_BS330) -#define U300_NR_IRQS 45 +#define U300_VIC_IRQS_END 45 #endif /* The DB3350-specific interrupt lines */ @@ -88,7 +88,7 @@ #define IRQ_U300_GPIO_PORT4 53 #define IRQ_U300_GPIO_PORT5 54 #define IRQ_U300_GPIO_PORT6 55 -#define U300_NR_IRQS 56 +#define U300_VIC_IRQS_END 56 #endif /* The DB3210-specific interrupt lines */ @@ -106,16 +106,25 @@ #define IRQ_U300_NFIF 45 #define IRQ_U300_NFIF2 46 #define IRQ_U300_SYSCON_PLL_LOCK 47 -#define U300_NR_IRQS 48 +#define U300_VIC_IRQS_END 48 #endif -#ifdef CONFIG_AB3550_CORE -#define IRQ_AB3550_BASE (U300_NR_IRQS) -#define IRQ_AB3550_END (IRQ_AB3550_BASE + 37) +/* Maximum 8*7 GPIO lines */ +#ifdef CONFIG_GPIO_U300 +#define IRQ_U300_GPIO_BASE (U300_VIC_IRQS_END) +#define IRQ_U300_GPIO_END (IRQ_U300_GPIO_BASE + 56) +#else +#define IRQ_U300_GPIO_END (U300_VIC_IRQS_END) +#endif -#define NR_IRQS (IRQ_AB3550_END + 1) +/* Optional AB3550 mixsig chip */ +#ifdef CONFIG_AB3550_CORE +#define IRQ_AB3550_BASE (IRQ_U300_GPIO_END) +#define IRQ_AB3550_END (IRQ_AB3550_BASE + 38) #else -#define NR_IRQS U300_NR_IRQS +#define IRQ_AB3550_END (IRQ_U300_GPIO_END) #endif +#define NR_IRQS (IRQ_AB3550_END) + #endif diff --git a/arch/arm/mach-u300/mmc.c b/arch/arm/mach-u300/mmc.c index 677ccef5cd32..d9a5c92db74a 100644 --- a/arch/arm/mach-u300/mmc.c +++ b/arch/arm/mach-u300/mmc.c @@ -13,12 +13,12 @@ #include <linux/device.h> #include <linux/amba/bus.h> #include <linux/mmc/host.h> -#include <linux/gpio.h> #include <linux/dmaengine.h> #include <linux/amba/mmci.h> #include <linux/slab.h> #include <mach/coh901318.h> #include <mach/dma_channels.h> +#include <mach/gpio-u300.h> #include "mmc.h" #include "padmux.h" diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c index f26fd76f72b4..15b23e4bd488 100644 --- a/arch/arm/mach-ux500/board-mop500-pins.c +++ b/arch/arm/mach-ux500/board-mop500-pins.c @@ -6,10 +6,10 @@ #include <linux/kernel.h> #include <linux/init.h> -#include <linux/gpio.h> #include <asm/mach-types.h> #include <plat/pincfg.h> +#include <plat/gpio-nomadik.h> #include <mach/hardware.h> #include "pins-db8500.h" diff --git a/arch/arm/mach-ux500/board-mop500-u8500uib.c b/arch/arm/mach-ux500/board-mop500-u8500uib.c index 8ce46c0fdfd5..feb5744d98b7 100644 --- a/arch/arm/mach-ux500/board-mop500-u8500uib.c +++ b/arch/arm/mach-ux500/board-mop500-u8500uib.c @@ -4,7 +4,7 @@ * Board data for the U8500 UIB, also known as the New UIB * License terms: GNU General Public License (GPL), version 2 */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/i2c.h> @@ -13,7 +13,6 @@ #include <linux/mfd/tc3589x.h> #include <linux/input/matrix_keypad.h> -#include <mach/gpio.h> #include <mach/irqs.h> #include "board-mop500.h" diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c index 2cc4876db212..f67b83dd9010 100644 --- a/arch/arm/mach-ux500/board-mop500.c +++ b/arch/arm/mach-ux500/board-mop500.c @@ -37,6 +37,7 @@ #include <plat/i2c.h> #include <plat/ste_dma40.h> #include <plat/pincfg.h> +#include <plat/gpio-nomadik.h> #include <mach/hardware.h> #include <mach/setup.h> diff --git a/arch/arm/mach-ux500/board-u5500-sdi.c b/arch/arm/mach-ux500/board-u5500-sdi.c index 739fb4c5b160..63c3f8058ffc 100644 --- a/arch/arm/mach-ux500/board-u5500-sdi.c +++ b/arch/arm/mach-ux500/board-u5500-sdi.c @@ -7,9 +7,9 @@ #include <linux/amba/mmci.h> #include <linux/mmc/host.h> -#include <linux/gpio.h> #include <plat/pincfg.h> +#include <plat/gpio-nomadik.h> #include <mach/db5500-regs.h> #include <plat/ste_dma40.h> diff --git a/arch/arm/mach-ux500/board-u5500.c b/arch/arm/mach-ux500/board-u5500.c index 166d47a5f4f3..e014aa749b03 100644 --- a/arch/arm/mach-ux500/board-u5500.c +++ b/arch/arm/mach-ux500/board-u5500.c @@ -8,7 +8,6 @@ #include <linux/init.h> #include <linux/platform_device.h> #include <linux/amba/bus.h> -#include <linux/gpio.h> #include <linux/irq.h> #include <linux/i2c.h> @@ -17,6 +16,7 @@ #include <plat/pincfg.h> #include <plat/i2c.h> +#include <plat/gpio-nomadik.h> #include <mach/hardware.h> #include <mach/devices.h> diff --git a/arch/arm/mach-ux500/cpu-db5500.c b/arch/arm/mach-ux500/cpu-db5500.c index 22705d246fc7..9de1af008094 100644 --- a/arch/arm/mach-ux500/cpu-db5500.c +++ b/arch/arm/mach-ux500/cpu-db5500.c @@ -13,7 +13,7 @@ #include <asm/mach/map.h> #include <asm/pmu.h> -#include <plat/gpio.h> +#include <plat/gpio-nomadik.h> #include <mach/hardware.h> #include <mach/devices.h> diff --git a/arch/arm/mach-ux500/cpu-db8500.c b/arch/arm/mach-ux500/cpu-db8500.c index 4598b06c8c55..13e8890a8b8a 100644 --- a/arch/arm/mach-ux500/cpu-db8500.c +++ b/arch/arm/mach-ux500/cpu-db8500.c @@ -14,12 +14,12 @@ #include <linux/amba/bus.h> #include <linux/interrupt.h> #include <linux/irq.h> -#include <linux/gpio.h> #include <linux/platform_device.h> #include <linux/io.h> #include <asm/mach/map.h> #include <asm/pmu.h> +#include <plat/gpio-nomadik.h> #include <mach/hardware.h> #include <mach/setup.h> #include <mach/devices.h> diff --git a/arch/arm/mach-ux500/devices-common.c b/arch/arm/mach-ux500/devices-common.c index 13a4ce046ae5..c563e5418d80 100644 --- a/arch/arm/mach-ux500/devices-common.c +++ b/arch/arm/mach-ux500/devices-common.c @@ -13,7 +13,7 @@ #include <linux/platform_device.h> #include <linux/amba/bus.h> -#include <plat/gpio.h> +#include <plat/gpio-nomadik.h> #include <mach/hardware.h> diff --git a/arch/arm/mach-ux500/include/mach/gpio.h b/arch/arm/mach-ux500/include/mach/gpio.h index 3c4cd31ad9f7..7389df911b1a 100644 --- a/arch/arm/mach-ux500/include/mach/gpio.h +++ b/arch/arm/mach-ux500/include/mach/gpio.h @@ -7,6 +7,4 @@ */ #define ARCH_NR_GPIOS 350 -#include <plat/gpio.h> - #endif /* __ASM_ARCH_GPIO_H */ diff --git a/arch/arm/mach-versatile/include/mach/gpio.h b/arch/arm/mach-versatile/include/mach/gpio.h index 94ff27678a46..40a8c178f10d 100644 --- a/arch/arm/mach-versatile/include/mach/gpio.h +++ b/arch/arm/mach-versatile/include/mach/gpio.h @@ -1,6 +1 @@ -#include <asm-generic/gpio.h> - -#define gpio_get_value __gpio_get_value -#define gpio_set_value __gpio_set_value -#define gpio_cansleep __gpio_cansleep -#define gpio_to_irq __gpio_to_irq +/* empty */ diff --git a/arch/arm/mach-vexpress/include/mach/io.h b/arch/arm/mach-vexpress/include/mach/io.h index 748bb524ee71..13522d86685e 100644 --- a/arch/arm/mach-vexpress/include/mach/io.h +++ b/arch/arm/mach-vexpress/include/mach/io.h @@ -20,8 +20,6 @@ #ifndef __ASM_ARM_ARCH_IO_H #define __ASM_ARM_ARCH_IO_H -#define IO_SPACE_LIMIT 0xffffffff - #define __io(a) __typesafe_io(a) #define __mem_pci(a) (a) diff --git a/arch/arm/mach-vt8500/include/mach/gpio.h b/arch/arm/mach-vt8500/include/mach/gpio.h index 94ff27678a46..40a8c178f10d 100644 --- a/arch/arm/mach-vt8500/include/mach/gpio.h +++ b/arch/arm/mach-vt8500/include/mach/gpio.h @@ -1,6 +1 @@ -#include <asm-generic/gpio.h> - -#define gpio_get_value __gpio_get_value -#define gpio_set_value __gpio_set_value -#define gpio_cansleep __gpio_cansleep -#define gpio_to_irq __gpio_to_irq +/* empty */ diff --git a/arch/arm/mach-vt8500/include/mach/io.h b/arch/arm/mach-vt8500/include/mach/io.h index 9077239f78c9..46181eecf273 100644 --- a/arch/arm/mach-vt8500/include/mach/io.h +++ b/arch/arm/mach-vt8500/include/mach/io.h @@ -20,8 +20,6 @@ #ifndef __ASM_ARM_ARCH_IO_H #define __ASM_ARM_ARCH_IO_H -#define IO_SPACE_LIMIT 0xffff - #define __io(a) __typesafe_io((a) + 0xf0000000) #define __mem_pci(a) (a) diff --git a/arch/arm/mach-w90x900/include/mach/gpio.h b/arch/arm/mach-w90x900/include/mach/gpio.h index 034da3e390c9..5385a4203277 100644 --- a/arch/arm/mach-w90x900/include/mach/gpio.h +++ b/arch/arm/mach-w90x900/include/mach/gpio.h @@ -15,16 +15,12 @@ #include <mach/hardware.h> #include <asm/irq.h> -#include <asm-generic/gpio.h> - -#define gpio_get_value __gpio_get_value -#define gpio_set_value __gpio_set_value -#define gpio_cansleep __gpio_cansleep static inline int gpio_to_irq(unsigned gpio) { return gpio; } +#define gpio_to_irq gpio_to_irq static inline int irq_to_gpio(unsigned irq) { diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig index 88633fe01a5d..7d5fff7b3632 100644 --- a/arch/arm/mm/Kconfig +++ b/arch/arm/mm/Kconfig @@ -822,7 +822,7 @@ config CACHE_L2X0 REALVIEW_EB_A9MP || SOC_IMX35 || SOC_IMX31 || MACH_REALVIEW_PBX || \ ARCH_NOMADIK || ARCH_OMAP4 || ARCH_EXYNOS4 || ARCH_TEGRA || \ ARCH_U8500 || ARCH_VEXPRESS_CA9X4 || ARCH_SHMOBILE || \ - ARCH_PRIMA2 || ARCH_ZYNQ || ARCH_CNS3XXX + ARCH_PRIMA2 || ARCH_ZYNQ || ARCH_CNS3XXX || ARCH_HIGHBANK default y select OUTER_CACHE select OUTER_CACHE_SYNC diff --git a/arch/arm/mm/cache-l2x0.c b/arch/arm/mm/cache-l2x0.c index 9ecfdb511951..3f9b9980478e 100644 --- a/arch/arm/mm/cache-l2x0.c +++ b/arch/arm/mm/cache-l2x0.c @@ -16,9 +16,12 @@ * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ +#include <linux/err.h> #include <linux/init.h> #include <linux/spinlock.h> #include <linux/io.h> +#include <linux/of.h> +#include <linux/of_address.h> #include <asm/cacheflush.h> #include <asm/hardware/cache-l2x0.h> @@ -30,11 +33,19 @@ static DEFINE_SPINLOCK(l2x0_lock); static uint32_t l2x0_way_mask; /* Bitmask of active ways */ static uint32_t l2x0_size; +struct l2x0_regs l2x0_saved_regs; + +struct l2x0_of_data { + void (*setup)(const struct device_node *, __u32 *, __u32 *); + void (*save)(void); + void (*resume)(void); +}; + static inline void cache_wait_way(void __iomem *reg, unsigned long mask) { /* wait for cache operation by line or way to complete */ while (readl_relaxed(reg) & mask) - ; + cpu_relax(); } #ifdef CONFIG_CACHE_PL310 @@ -277,7 +288,7 @@ static void l2x0_disable(void) spin_unlock_irqrestore(&l2x0_lock, flags); } -static void __init l2x0_unlock(__u32 cache_id) +static void l2x0_unlock(__u32 cache_id) { int lockregs; int i; @@ -353,6 +364,8 @@ void __init l2x0_init(void __iomem *base, __u32 aux_val, __u32 aux_mask) /* l2x0 controller is disabled */ writel_relaxed(aux, l2x0_base + L2X0_AUX_CTRL); + l2x0_saved_regs.aux_ctrl = aux; + l2x0_inv_all(); /* enable L2X0 */ @@ -372,3 +385,202 @@ void __init l2x0_init(void __iomem *base, __u32 aux_val, __u32 aux_mask) printk(KERN_INFO "l2x0: %d ways, CACHE_ID 0x%08x, AUX_CTRL 0x%08x, Cache size: %d B\n", ways, cache_id, aux, l2x0_size); } + +#ifdef CONFIG_OF +static void __init l2x0_of_setup(const struct device_node *np, + __u32 *aux_val, __u32 *aux_mask) +{ + u32 data[2] = { 0, 0 }; + u32 tag = 0; + u32 dirty = 0; + u32 val = 0, mask = 0; + + of_property_read_u32(np, "arm,tag-latency", &tag); + if (tag) { + mask |= L2X0_AUX_CTRL_TAG_LATENCY_MASK; + val |= (tag - 1) << L2X0_AUX_CTRL_TAG_LATENCY_SHIFT; + } + + of_property_read_u32_array(np, "arm,data-latency", + data, ARRAY_SIZE(data)); + if (data[0] && data[1]) { + mask |= L2X0_AUX_CTRL_DATA_RD_LATENCY_MASK | + L2X0_AUX_CTRL_DATA_WR_LATENCY_MASK; + val |= ((data[0] - 1) << L2X0_AUX_CTRL_DATA_RD_LATENCY_SHIFT) | + ((data[1] - 1) << L2X0_AUX_CTRL_DATA_WR_LATENCY_SHIFT); + } + + of_property_read_u32(np, "arm,dirty-latency", &dirty); + if (dirty) { + mask |= L2X0_AUX_CTRL_DIRTY_LATENCY_MASK; + val |= (dirty - 1) << L2X0_AUX_CTRL_DIRTY_LATENCY_SHIFT; + } + + *aux_val &= ~mask; + *aux_val |= val; + *aux_mask &= ~mask; +} + +static void __init pl310_of_setup(const struct device_node *np, + __u32 *aux_val, __u32 *aux_mask) +{ + u32 data[3] = { 0, 0, 0 }; + u32 tag[3] = { 0, 0, 0 }; + u32 filter[2] = { 0, 0 }; + + of_property_read_u32_array(np, "arm,tag-latency", tag, ARRAY_SIZE(tag)); + if (tag[0] && tag[1] && tag[2]) + writel_relaxed( + ((tag[0] - 1) << L2X0_LATENCY_CTRL_RD_SHIFT) | + ((tag[1] - 1) << L2X0_LATENCY_CTRL_WR_SHIFT) | + ((tag[2] - 1) << L2X0_LATENCY_CTRL_SETUP_SHIFT), + l2x0_base + L2X0_TAG_LATENCY_CTRL); + + of_property_read_u32_array(np, "arm,data-latency", + data, ARRAY_SIZE(data)); + if (data[0] && data[1] && data[2]) + writel_relaxed( + ((data[0] - 1) << L2X0_LATENCY_CTRL_RD_SHIFT) | + ((data[1] - 1) << L2X0_LATENCY_CTRL_WR_SHIFT) | + ((data[2] - 1) << L2X0_LATENCY_CTRL_SETUP_SHIFT), + l2x0_base + L2X0_DATA_LATENCY_CTRL); + + of_property_read_u32_array(np, "arm,filter-ranges", + filter, ARRAY_SIZE(filter)); + if (filter[1]) { + writel_relaxed(ALIGN(filter[0] + filter[1], SZ_1M), + l2x0_base + L2X0_ADDR_FILTER_END); + writel_relaxed((filter[0] & ~(SZ_1M - 1)) | L2X0_ADDR_FILTER_EN, + l2x0_base + L2X0_ADDR_FILTER_START); + } +} + +static void __init pl310_save(void) +{ + u32 l2x0_revision = readl_relaxed(l2x0_base + L2X0_CACHE_ID) & + L2X0_CACHE_ID_RTL_MASK; + + l2x0_saved_regs.tag_latency = readl_relaxed(l2x0_base + + L2X0_TAG_LATENCY_CTRL); + l2x0_saved_regs.data_latency = readl_relaxed(l2x0_base + + L2X0_DATA_LATENCY_CTRL); + l2x0_saved_regs.filter_end = readl_relaxed(l2x0_base + + L2X0_ADDR_FILTER_END); + l2x0_saved_regs.filter_start = readl_relaxed(l2x0_base + + L2X0_ADDR_FILTER_START); + + if (l2x0_revision >= L2X0_CACHE_ID_RTL_R2P0) { + /* + * From r2p0, there is Prefetch offset/control register + */ + l2x0_saved_regs.prefetch_ctrl = readl_relaxed(l2x0_base + + L2X0_PREFETCH_CTRL); + /* + * From r3p0, there is Power control register + */ + if (l2x0_revision >= L2X0_CACHE_ID_RTL_R3P0) + l2x0_saved_regs.pwr_ctrl = readl_relaxed(l2x0_base + + L2X0_POWER_CTRL); + } +} + +static void l2x0_resume(void) +{ + if (!(readl_relaxed(l2x0_base + L2X0_CTRL) & 1)) { + /* restore aux ctrl and enable l2 */ + l2x0_unlock(readl_relaxed(l2x0_base + L2X0_CACHE_ID)); + + writel_relaxed(l2x0_saved_regs.aux_ctrl, l2x0_base + + L2X0_AUX_CTRL); + + l2x0_inv_all(); + + writel_relaxed(1, l2x0_base + L2X0_CTRL); + } +} + +static void pl310_resume(void) +{ + u32 l2x0_revision; + + if (!(readl_relaxed(l2x0_base + L2X0_CTRL) & 1)) { + /* restore pl310 setup */ + writel_relaxed(l2x0_saved_regs.tag_latency, + l2x0_base + L2X0_TAG_LATENCY_CTRL); + writel_relaxed(l2x0_saved_regs.data_latency, + l2x0_base + L2X0_DATA_LATENCY_CTRL); + writel_relaxed(l2x0_saved_regs.filter_end, + l2x0_base + L2X0_ADDR_FILTER_END); + writel_relaxed(l2x0_saved_regs.filter_start, + l2x0_base + L2X0_ADDR_FILTER_START); + + l2x0_revision = readl_relaxed(l2x0_base + L2X0_CACHE_ID) & + L2X0_CACHE_ID_RTL_MASK; + + if (l2x0_revision >= L2X0_CACHE_ID_RTL_R2P0) { + writel_relaxed(l2x0_saved_regs.prefetch_ctrl, + l2x0_base + L2X0_PREFETCH_CTRL); + if (l2x0_revision >= L2X0_CACHE_ID_RTL_R3P0) + writel_relaxed(l2x0_saved_regs.pwr_ctrl, + l2x0_base + L2X0_POWER_CTRL); + } + } + + l2x0_resume(); +} + +static const struct l2x0_of_data pl310_data = { + pl310_of_setup, + pl310_save, + pl310_resume, +}; + +static const struct l2x0_of_data l2x0_data = { + l2x0_of_setup, + NULL, + l2x0_resume, +}; + +static const struct of_device_id l2x0_ids[] __initconst = { + { .compatible = "arm,pl310-cache", .data = (void *)&pl310_data }, + { .compatible = "arm,l220-cache", .data = (void *)&l2x0_data }, + { .compatible = "arm,l210-cache", .data = (void *)&l2x0_data }, + {} +}; + +int __init l2x0_of_init(__u32 aux_val, __u32 aux_mask) +{ + struct device_node *np; + struct l2x0_of_data *data; + struct resource res; + + np = of_find_matching_node(NULL, l2x0_ids); + if (!np) + return -ENODEV; + + if (of_address_to_resource(np, 0, &res)) + return -ENODEV; + + l2x0_base = ioremap(res.start, resource_size(&res)); + if (!l2x0_base) + return -ENOMEM; + + l2x0_saved_regs.phy_base = res.start; + + data = of_match_node(l2x0_ids, np)->data; + + /* L2 configuration can only be changed if the cache is disabled */ + if (!(readl_relaxed(l2x0_base + L2X0_CTRL) & 1)) { + if (data->setup) + data->setup(np, &aux_val, &aux_mask); + } + + if (data->save) + data->save(); + + l2x0_init(l2x0_base, aux_val, aux_mask); + + outer_cache.resume = data->resume; + return 0; +} +#endif diff --git a/arch/arm/plat-mxc/include/mach/gpio.h b/arch/arm/plat-mxc/include/mach/gpio.h index 44af0064ba1a..40a8c178f10d 100644 --- a/arch/arm/plat-mxc/include/mach/gpio.h +++ b/arch/arm/plat-mxc/include/mach/gpio.h @@ -1,32 +1 @@ -/* - * Copyright 2007 Freescale Semiconductor, Inc. All Rights Reserved. - * Copyright 2008 Juergen Beisert, kernel@pengutronix.de - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version 2 - * of the License, or (at your option) any later version. - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA. - */ - -#ifndef __ASM_ARCH_MXC_GPIO_H__ -#define __ASM_ARCH_MXC_GPIO_H__ - -#include <linux/spinlock.h> -#include <mach/hardware.h> -#include <asm-generic/gpio.h> - -/* use gpiolib dispatchers */ -#define gpio_get_value __gpio_get_value -#define gpio_set_value __gpio_set_value -#define gpio_cansleep __gpio_cansleep -#define gpio_to_irq __gpio_to_irq - -#endif +/* empty */ diff --git a/arch/arm/plat-nomadik/include/plat/gpio.h b/arch/arm/plat-nomadik/include/plat/gpio-nomadik.h index d5d7e651269c..3ba4d8f8073b 100644 --- a/arch/arm/plat-nomadik/include/plat/gpio.h +++ b/arch/arm/plat-nomadik/include/plat/gpio-nomadik.h @@ -9,20 +9,9 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ -#ifndef __ASM_PLAT_GPIO_H -#define __ASM_PLAT_GPIO_H -#include <asm-generic/gpio.h> - -/* - * These currently cause a function call to happen, they may be optimized - * if needed by adding cpu-specific defines to identify blocks - * (see mach-pxa/include/mach/gpio.h as an example using GPLR etc) - */ -#define gpio_get_value __gpio_get_value -#define gpio_set_value __gpio_set_value -#define gpio_cansleep __gpio_cansleep -#define gpio_to_irq __gpio_to_irq +#ifndef __PLAT_NOMADIK_GPIO +#define __PLAT_NOMADIK_GPIO /* * "nmk_gpio" and "NMK_GPIO" stand for "Nomadik GPIO", leaving @@ -93,4 +82,4 @@ struct nmk_gpio_platform_data { bool supports_sleepmode; }; -#endif /* __ASM_PLAT_GPIO_H */ +#endif /* __PLAT_NOMADIK_GPIO */ diff --git a/arch/arm/plat-omap/debug-devices.c b/arch/arm/plat-omap/debug-devices.c index 923c9621096b..caa1f7b6cc21 100644 --- a/arch/arm/plat-omap/debug-devices.c +++ b/arch/arm/plat-omap/debug-devices.c @@ -8,7 +8,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -18,7 +18,6 @@ #include <mach/hardware.h> #include <plat/board.h> -#include <mach/gpio.h> /* Many OMAP development platforms reuse the same "debug board"; these diff --git a/arch/arm/plat-omap/debug-leds.c b/arch/arm/plat-omap/debug-leds.c index fc05b1022602..61a1ec2a6af4 100644 --- a/arch/arm/plat-omap/debug-leds.c +++ b/arch/arm/plat-omap/debug-leds.c @@ -7,7 +7,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/init.h> #include <linux/platform_device.h> #include <linux/leds.h> @@ -19,7 +19,6 @@ #include <asm/mach-types.h> #include <plat/fpga.h> -#include <mach/gpio.h> /* Many OMAP development platforms reuse the same "debug board"; these diff --git a/arch/arm/plat-omap/devices.c b/arch/arm/plat-omap/devices.c index bd9a06b3ee89..acd132c29647 100644 --- a/arch/arm/plat-omap/devices.c +++ b/arch/arm/plat-omap/devices.c @@ -8,7 +8,7 @@ * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. */ - +#include <linux/gpio.h> #include <linux/module.h> #include <linux/kernel.h> #include <linux/init.h> @@ -24,7 +24,6 @@ #include <plat/tc.h> #include <plat/board.h> #include <plat/mmc.h> -#include <mach/gpio.h> #include <plat/menelaus.h> #include <plat/omap44xx.h> diff --git a/arch/arm/plat-omap/include/plat/gpio.h b/arch/arm/plat-omap/include/plat/gpio.h index 91e8de3db085..9e86ee0aed0a 100644 --- a/arch/arm/plat-omap/include/plat/gpio.h +++ b/arch/arm/plat-omap/include/plat/gpio.h @@ -222,26 +222,6 @@ extern void omap_gpio_restore_context(void); #include <linux/errno.h> #include <asm-generic/gpio.h> -static inline int gpio_get_value(unsigned gpio) -{ - return __gpio_get_value(gpio); -} - -static inline void gpio_set_value(unsigned gpio, int value) -{ - __gpio_set_value(gpio, value); -} - -static inline int gpio_cansleep(unsigned gpio) -{ - return __gpio_cansleep(gpio); -} - -static inline int gpio_to_irq(unsigned gpio) -{ - return __gpio_to_irq(gpio); -} - static inline int irq_to_gpio(unsigned irq) { int tmp; diff --git a/arch/arm/plat-orion/include/plat/gpio.h b/arch/arm/plat-orion/include/plat/gpio.h index 3075b9fdde83..3abf30428bee 100644 --- a/arch/arm/plat-orion/include/plat/gpio.h +++ b/arch/arm/plat-orion/include/plat/gpio.h @@ -12,15 +12,7 @@ #define __PLAT_GPIO_H #include <linux/init.h> -#include <asm-generic/gpio.h> - -/* - * GENERIC_GPIO primitives. - */ -#define gpio_get_value __gpio_get_value -#define gpio_set_value __gpio_set_value -#define gpio_cansleep __gpio_cansleep -#define gpio_to_irq __gpio_to_irq +#include <linux/types.h> /* * Orion-specific GPIO API extensions. diff --git a/arch/arm/plat-pxa/Makefile b/arch/arm/plat-pxa/Makefile index 3aca5ba0f876..f302d048392d 100644 --- a/arch/arm/plat-pxa/Makefile +++ b/arch/arm/plat-pxa/Makefile @@ -4,7 +4,6 @@ obj-y := dma.o -obj-$(CONFIG_GENERIC_GPIO) += gpio.o obj-$(CONFIG_PXA3xx) += mfp.o obj-$(CONFIG_PXA95x) += mfp.o obj-$(CONFIG_ARCH_MMP) += mfp.o diff --git a/arch/arm/plat-pxa/include/plat/gpio-pxa.h b/arch/arm/plat-pxa/include/plat/gpio-pxa.h new file mode 100644 index 000000000000..b6390beff323 --- /dev/null +++ b/arch/arm/plat-pxa/include/plat/gpio-pxa.h @@ -0,0 +1,44 @@ +#ifndef __PLAT_PXA_GPIO_H +#define __PLAT_PXA_GPIO_H + +struct irq_data; + +/* + * We handle the GPIOs by banks, each bank covers up to 32 GPIOs with + * one set of registers. The register offsets are organized below: + * + * GPLR GPDR GPSR GPCR GRER GFER GEDR + * BANK 0 - 0x0000 0x000C 0x0018 0x0024 0x0030 0x003C 0x0048 + * BANK 1 - 0x0004 0x0010 0x001C 0x0028 0x0034 0x0040 0x004C + * BANK 2 - 0x0008 0x0014 0x0020 0x002C 0x0038 0x0044 0x0050 + * + * BANK 3 - 0x0100 0x010C 0x0118 0x0124 0x0130 0x013C 0x0148 + * BANK 4 - 0x0104 0x0110 0x011C 0x0128 0x0134 0x0140 0x014C + * BANK 5 - 0x0108 0x0114 0x0120 0x012C 0x0138 0x0144 0x0150 + * + * NOTE: + * BANK 3 is only available on PXA27x and later processors. + * BANK 4 and 5 are only available on PXA935 + */ + +#define GPIO_BANK(n) (GPIO_REGS_VIRT + BANK_OFF(n)) + +#define GPLR_OFFSET 0x00 +#define GPDR_OFFSET 0x0C +#define GPSR_OFFSET 0x18 +#define GPCR_OFFSET 0x24 +#define GRER_OFFSET 0x30 +#define GFER_OFFSET 0x3C +#define GEDR_OFFSET 0x48 + +/* NOTE: some PXAs have fewer on-chip GPIOs (like PXA255, with 85). + * Those cases currently cause holes in the GPIO number space, the + * actual number of the last GPIO is recorded by 'pxa_last_gpio'. + */ +extern int pxa_last_gpio; + +typedef int (*set_wake_t)(struct irq_data *d, unsigned int on); + +extern void pxa_init_gpio(int mux_irq, int start, int end, set_wake_t fn); + +#endif /* __PLAT_PXA_GPIO_H */ diff --git a/arch/arm/plat-pxa/include/plat/gpio.h b/arch/arm/plat-pxa/include/plat/gpio.h index 1ddd2b97a729..258f77210b02 100644 --- a/arch/arm/plat-pxa/include/plat/gpio.h +++ b/arch/arm/plat-pxa/include/plat/gpio.h @@ -1,35 +1,10 @@ #ifndef __PLAT_GPIO_H #define __PLAT_GPIO_H -struct irq_data; +#define __ARM_GPIOLIB_COMPLEX -/* - * We handle the GPIOs by banks, each bank covers up to 32 GPIOs with - * one set of registers. The register offsets are organized below: - * - * GPLR GPDR GPSR GPCR GRER GFER GEDR - * BANK 0 - 0x0000 0x000C 0x0018 0x0024 0x0030 0x003C 0x0048 - * BANK 1 - 0x0004 0x0010 0x001C 0x0028 0x0034 0x0040 0x004C - * BANK 2 - 0x0008 0x0014 0x0020 0x002C 0x0038 0x0044 0x0050 - * - * BANK 3 - 0x0100 0x010C 0x0118 0x0124 0x0130 0x013C 0x0148 - * BANK 4 - 0x0104 0x0110 0x011C 0x0128 0x0134 0x0140 0x014C - * BANK 5 - 0x0108 0x0114 0x0120 0x012C 0x0138 0x0144 0x0150 - * - * NOTE: - * BANK 3 is only available on PXA27x and later processors. - * BANK 4 and 5 are only available on PXA935 - */ - -#define GPIO_BANK(n) (GPIO_REGS_VIRT + BANK_OFF(n)) - -#define GPLR_OFFSET 0x00 -#define GPDR_OFFSET 0x0C -#define GPSR_OFFSET 0x18 -#define GPCR_OFFSET 0x24 -#define GRER_OFFSET 0x30 -#define GFER_OFFSET 0x3C -#define GEDR_OFFSET 0x48 +/* The individual machine provides register offsets and NR_BUILTIN_GPIO */ +#include <mach/gpio-pxa.h> static inline int gpio_get_value(unsigned gpio) { @@ -52,13 +27,4 @@ static inline void gpio_set_value(unsigned gpio, int value) #define gpio_cansleep __gpio_cansleep -/* NOTE: some PXAs have fewer on-chip GPIOs (like PXA255, with 85). - * Those cases currently cause holes in the GPIO number space, the - * actual number of the last GPIO is recorded by 'pxa_last_gpio'. - */ -extern int pxa_last_gpio; - -typedef int (*set_wake_t)(struct irq_data *d, unsigned int on); - -extern void pxa_init_gpio(int mux_irq, int start, int end, set_wake_t fn); #endif /* __PLAT_GPIO_H */ diff --git a/arch/arm/plat-spear/include/plat/gpio.h b/arch/arm/plat-spear/include/plat/gpio.h index b857c91257dd..40a8c178f10d 100644 --- a/arch/arm/plat-spear/include/plat/gpio.h +++ b/arch/arm/plat-spear/include/plat/gpio.h @@ -1,24 +1 @@ -/* - * arch/arm/plat-spear/include/plat/gpio.h - * - * GPIO macros for SPEAr platform - * - * Copyright (C) 2009 ST Microelectronics - * Viresh Kumar<viresh.kumar@st.com> - * - * This file is licensed under the terms of the GNU General Public - * License version 2. This program is licensed "as is" without any - * warranty of any kind, whether express or implied. - */ - -#ifndef __PLAT_GPIO_H -#define __PLAT_GPIO_H - -#include <asm-generic/gpio.h> - -#define gpio_get_value __gpio_get_value -#define gpio_set_value __gpio_set_value -#define gpio_cansleep __gpio_cansleep -#define gpio_to_irq __gpio_to_irq - -#endif /* __PLAT_GPIO_H */ +/* empty */ diff --git a/drivers/ata/pata_at91.c b/drivers/ata/pata_at91.c index 960c72571395..3f4c2613b3df 100644 --- a/drivers/ata/pata_at91.c +++ b/drivers/ata/pata_at91.c @@ -30,7 +30,7 @@ #include <mach/at91sam9_smc.h> #include <mach/board.h> -#include <mach/gpio.h> +#include <asm/gpio.h> #define DRV_NAME "pata_at91" #define DRV_VERSION "0.3" diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig index d539efd96d4b..4caa3d37bbde 100644 --- a/drivers/gpio/Kconfig +++ b/drivers/gpio/Kconfig @@ -178,6 +178,15 @@ config GPIO_SCH The Intel Tunnel Creek processor has 5 GPIOs powered by the core power rail and 9 from suspend power supply. +config GPIO_U300 + bool "ST-Ericsson U300 COH 901 335/571 GPIO" + depends on GPIOLIB && ARCH_U300 + help + Say yes here to support GPIO interface on ST-Ericsson U300. + The names of the two IP block variants supported are + COH 901 335 and COH 901 571/3. They contain 3, 5 or 7 + ports of 8 GPIO pins each. + config GPIO_VX855 tristate "VIA VX855/VX875 GPIO" depends on MFD_SUPPORT && PCI diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile index 9588948c96f0..19c5d27b6d2e 100644 --- a/drivers/gpio/Makefile +++ b/drivers/gpio/Makefile @@ -14,11 +14,14 @@ obj-$(CONFIG_GPIO_ADP5588) += gpio-adp5588.o obj-$(CONFIG_GPIO_BT8XX) += gpio-bt8xx.o obj-$(CONFIG_GPIO_CS5535) += gpio-cs5535.o obj-$(CONFIG_GPIO_DA9052) += gpio-da9052.o +obj-$(CONFIG_ARCH_DAVINCI) += gpio-davinci.o obj-$(CONFIG_GPIO_EP93XX) += gpio-ep93xx.o obj-$(CONFIG_GPIO_EXYNOS4) += gpio-exynos4.o obj-$(CONFIG_GPIO_IT8761E) += gpio-it8761e.o obj-$(CONFIG_GPIO_JANZ_TTL) += gpio-janz-ttl.o +obj-$(CONFIG_MACH_KS8695) += gpio-ks8695.o obj-$(CONFIG_GPIO_LANGWELL) += gpio-langwell.o +obj-$(CONFIG_ARCH_LPC32XX) += gpio-lpc32xx.o obj-$(CONFIG_GPIO_MAX730X) += gpio-max730x.o obj-$(CONFIG_GPIO_MAX7300) += gpio-max7300.o obj-$(CONFIG_GPIO_MAX7301) += gpio-max7301.o @@ -37,18 +40,20 @@ obj-$(CONFIG_GPIO_PCA953X) += gpio-pca953x.o obj-$(CONFIG_GPIO_PCF857X) += gpio-pcf857x.o obj-$(CONFIG_GPIO_PCH) += gpio-pch.o obj-$(CONFIG_GPIO_PL061) += gpio-pl061.o +obj-$(CONFIG_PLAT_PXA) += gpio-pxa.o obj-$(CONFIG_GPIO_RDC321X) += gpio-rdc321x.o obj-$(CONFIG_GPIO_PLAT_SAMSUNG) += gpio-plat-samsung.o obj-$(CONFIG_GPIO_S5PC100) += gpio-s5pc100.o obj-$(CONFIG_GPIO_S5PV210) += gpio-s5pv210.o - +obj-$(CONFIG_ARCH_SA1100) += gpio-sa1100.o obj-$(CONFIG_GPIO_SCH) += gpio-sch.o obj-$(CONFIG_GPIO_STMPE) += gpio-stmpe.o obj-$(CONFIG_GPIO_SX150X) += gpio-sx150x.o obj-$(CONFIG_GPIO_TC3589X) += gpio-tc3589x.o obj-$(CONFIG_ARCH_TEGRA) += gpio-tegra.o obj-$(CONFIG_GPIO_TIMBERDALE) += gpio-timberdale.o +obj-$(CONFIG_ARCH_DAVINCI_TNETV107X) += gpio-tnetv107x.o obj-$(CONFIG_GPIO_TPS65910) += gpio-tps65910.o obj-$(CONFIG_GPIO_TPS65912) += gpio-tps65912.o obj-$(CONFIG_GPIO_TWL4030) += gpio-twl4030.o diff --git a/arch/arm/mach-davinci/gpio.c b/drivers/gpio/gpio-davinci.c index cafbe13a82a5..df0d59570a84 100644 --- a/arch/arm/mach-davinci/gpio.c +++ b/drivers/gpio/gpio-davinci.c @@ -9,15 +9,13 @@ * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. */ - +#include <linux/gpio.h> #include <linux/errno.h> #include <linux/kernel.h> #include <linux/clk.h> #include <linux/err.h> #include <linux/io.h> -#include <mach/gpio.h> - #include <asm/mach/irq.h> struct davinci_gpio_regs { @@ -232,9 +230,6 @@ static void gpio_irq_enable(struct irq_data *d) static int gpio_irq_type(struct irq_data *d, unsigned trigger) { - struct davinci_gpio_regs __iomem *g = irq2regs(d->irq); - u32 mask = (u32) irq_data_get_irq_handler_data(d); - if (trigger & ~(IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_EDGE_RISING)) return -EINVAL; diff --git a/drivers/gpio/gpio-ep93xx.c b/drivers/gpio/gpio-ep93xx.c index 72fb9c665320..7aafbb437339 100644 --- a/drivers/gpio/gpio-ep93xx.c +++ b/drivers/gpio/gpio-ep93xx.c @@ -23,6 +23,9 @@ #include <linux/basic_mmio_gpio.h> #include <mach/hardware.h> +#include <mach/gpio-ep93xx.h> + +#define irq_to_gpio(irq) ((irq) - gpio_to_irq(0)) struct ep93xx_gpio { void __iomem *mmio_base; @@ -307,6 +310,21 @@ static int ep93xx_gpio_set_debounce(struct gpio_chip *chip, return 0; } +/* + * Map GPIO A0..A7 (0..7) to irq 64..71, + * B0..B7 (7..15) to irq 72..79, and + * F0..F7 (16..24) to irq 80..87. + */ +static int ep93xx_gpio_to_irq(struct gpio_chip *chip, unsigned offset) +{ + int gpio = chip->base + offset; + + if (gpio > EP93XX_GPIO_LINE_MAX_IRQ) + return -EINVAL; + + return 64 + gpio; +} + static int ep93xx_gpio_add_bank(struct bgpio_chip *bgc, struct device *dev, void __iomem *mmio_base, struct ep93xx_gpio_bank *bank) { @@ -321,8 +339,10 @@ static int ep93xx_gpio_add_bank(struct bgpio_chip *bgc, struct device *dev, bgc->gc.label = bank->label; bgc->gc.base = bank->base; - if (bank->has_debounce) + if (bank->has_debounce) { bgc->gc.set_debounce = ep93xx_gpio_set_debounce; + bgc->gc.to_irq = ep93xx_gpio_to_irq; + } return gpiochip_add(&bgc->gc); } diff --git a/arch/arm/mach-ks8695/gpio.c b/drivers/gpio/gpio-ks8695.c index 31e456508a6f..a3ac66ea364b 100644 --- a/arch/arm/mach-ks8695/gpio.c +++ b/drivers/gpio/gpio-ks8695.c @@ -18,7 +18,7 @@ * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/mm.h> #include <linux/init.h> @@ -31,7 +31,7 @@ #include <asm/mach/irq.h> #include <mach/regs-gpio.h> -#include <mach/gpio.h> +#include <mach/gpio-ks8695.h> /* * Configure a GPIO line for either GPIO function, or its internal diff --git a/arch/arm/mach-lpc32xx/gpiolib.c b/drivers/gpio/gpio-lpc32xx.c index 69061ea8997a..5b6948081f8f 100644 --- a/arch/arm/mach-lpc32xx/gpiolib.c +++ b/drivers/gpio/gpio-lpc32xx.c @@ -24,7 +24,7 @@ #include <mach/hardware.h> #include <mach/platform.h> -#include "common.h" +#include <mach/gpio-lpc32xx.h> #define LPC32XX_GPIO_P3_INP_STATE _GPREG(0x000) #define LPC32XX_GPIO_P3_OUTP_SET _GPREG(0x004) diff --git a/drivers/gpio/gpio-nomadik.c b/drivers/gpio/gpio-nomadik.c index 2c212c732d76..740caed2b278 100644 --- a/drivers/gpio/gpio-nomadik.c +++ b/drivers/gpio/gpio-nomadik.c @@ -27,8 +27,9 @@ #include <asm/mach/irq.h> #include <plat/pincfg.h> +#include <plat/gpio-nomadik.h> #include <mach/hardware.h> -#include <mach/gpio.h> +#include <asm/gpio.h> /* * The GPIO module in the Nomadik family of Systems-on-Chip is an diff --git a/drivers/gpio/gpio-omap.c b/drivers/gpio/gpio-omap.c index 118ec12d2d5f..0e49d87f6c60 100644 --- a/drivers/gpio/gpio-omap.c +++ b/drivers/gpio/gpio-omap.c @@ -25,7 +25,7 @@ #include <mach/hardware.h> #include <asm/irq.h> #include <mach/irqs.h> -#include <mach/gpio.h> +#include <asm/gpio.h> #include <asm/mach/irq.h> struct gpio_bank { diff --git a/arch/arm/plat-pxa/gpio.c b/drivers/gpio/gpio-pxa.c index a11dc3670505..9052925c6fa2 100644 --- a/arch/arm/plat-pxa/gpio.c +++ b/drivers/gpio/gpio-pxa.c @@ -11,14 +11,14 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/init.h> #include <linux/irq.h> #include <linux/io.h> #include <linux/syscore_ops.h> #include <linux/slab.h> -#include <mach/gpio.h> +#include <mach/gpio-pxa.h> int pxa_last_gpio; diff --git a/arch/arm/mach-sa1100/gpio.c b/drivers/gpio/gpio-sa1100.c index 0d3829a8c2c1..b6c1f6d80649 100644 --- a/arch/arm/mach-sa1100/gpio.c +++ b/drivers/gpio/gpio-sa1100.c @@ -7,13 +7,11 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ - +#include <linux/gpio.h> #include <linux/init.h> #include <linux/module.h> -#include <asm/gpio.h> #include <mach/hardware.h> -#include "generic.h" static int sa1100_gpio_get(struct gpio_chip *chip, unsigned offset) { diff --git a/drivers/gpio/gpio-tegra.c b/drivers/gpio/gpio-tegra.c index 747eb40e8afe..6b65207c8106 100644 --- a/drivers/gpio/gpio-tegra.c +++ b/drivers/gpio/gpio-tegra.c @@ -27,6 +27,7 @@ #include <asm/mach/irq.h> +#include <mach/gpio-tegra.h> #include <mach/iomap.h> #include <mach/suspend.h> @@ -134,7 +135,10 @@ static int tegra_gpio_direction_output(struct gpio_chip *chip, unsigned offset, return 0; } - +static int tegra_gpio_to_irq(struct gpio_chip *chip, unsigned offset) +{ + return TEGRA_GPIO_TO_IRQ(offset); +} static struct gpio_chip tegra_gpio_chip = { .label = "tegra-gpio", @@ -142,6 +146,7 @@ static struct gpio_chip tegra_gpio_chip = { .get = tegra_gpio_get, .direction_output = tegra_gpio_direction_output, .set = tegra_gpio_set, + .to_irq = tegra_gpio_to_irq, .base = 0, .ngpio = TEGRA_NR_GPIOS, }; @@ -331,6 +336,7 @@ static struct lock_class_key gpio_lock_class; static int __init tegra_gpio_init(void) { struct tegra_gpio_bank *bank; + int gpio; int i; int j; @@ -352,14 +358,17 @@ static int __init tegra_gpio_init(void) gpiochip_add(&tegra_gpio_chip); - for (i = INT_GPIO_BASE; i < (INT_GPIO_BASE + TEGRA_NR_GPIOS); i++) { - bank = &tegra_gpio_banks[GPIO_BANK(irq_to_gpio(i))]; + for (gpio = 0; gpio < TEGRA_NR_GPIOS; gpio++) { + int irq = TEGRA_GPIO_TO_IRQ(gpio); + /* No validity check; all Tegra GPIOs are valid IRQs */ + + bank = &tegra_gpio_banks[GPIO_BANK(gpio)]; - irq_set_lockdep_class(i, &gpio_lock_class); - irq_set_chip_data(i, bank); - irq_set_chip_and_handler(i, &tegra_gpio_irq_chip, + irq_set_lockdep_class(irq, &gpio_lock_class); + irq_set_chip_data(irq, bank); + irq_set_chip_and_handler(irq, &tegra_gpio_irq_chip, handle_simple_irq); - set_irq_flags(i, IRQF_VALID); + set_irq_flags(irq, IRQF_VALID); } for (i = 0; i < ARRAY_SIZE(tegra_gpio_banks); i++) { diff --git a/arch/arm/mach-davinci/gpio-tnetv107x.c b/drivers/gpio/gpio-tnetv107x.c index 3fa3e2867e19..3fa3e2867e19 100644 --- a/arch/arm/mach-davinci/gpio-tnetv107x.c +++ b/drivers/gpio/gpio-tnetv107x.c diff --git a/drivers/gpio/gpio-u300.c b/drivers/gpio/gpio-u300.c index 53e8255cb0ba..4035778852b0 100644 --- a/drivers/gpio/gpio-u300.c +++ b/drivers/gpio/gpio-u300.c @@ -1,18 +1,17 @@ /* * U300 GPIO module. * - * Copyright (C) 2007-2009 ST-Ericsson AB + * Copyright (C) 2007-2011 ST-Ericsson AB * License terms: GNU General Public License (GPL) version 2 * This can driver either of the two basic GPIO cores * available in the U300 platforms: * COH 901 335 - Used in DB3150 (U300 1.0) and DB3200 (U330 1.0) * COH 901 571/3 - Used in DB3210 (U365 2.0) and DB3350 (U335 1.0) - * Notice that you also have inline macros in <asm-arch/gpio.h> - * Author: Linus Walleij <linus.walleij@stericsson.com> + * Author: Linus Walleij <linus.walleij@linaro.org> * Author: Jonas Aaberg <jonas.aberg@stericsson.com> - * */ #include <linux/module.h> +#include <linux/irq.h> #include <linux/interrupt.h> #include <linux/delay.h> #include <linux/errno.h> @@ -21,677 +20,898 @@ #include <linux/err.h> #include <linux/platform_device.h> #include <linux/gpio.h> +#include <linux/list.h> +#include <linux/slab.h> +#include <mach/gpio-u300.h> -/* Reference to GPIO block clock */ -static struct clk *clk; +/* + * Bias modes for U300 GPIOs + * + * GPIO_U300_CONFIG_BIAS_UNKNOWN: this bias mode is not known to us + * GPIO_U300_CONFIG_BIAS_FLOAT: no specific bias, the GPIO will float or state + * is not controlled by software + * GPIO_U300_CONFIG_BIAS_PULL_UP: the GPIO will be pulled up (usually with high + * impedance to VDD) + */ +#define GPIO_U300_CONFIG_BIAS_UNKNOWN 0x1000 +#define GPIO_U300_CONFIG_BIAS_FLOAT 0x1001 +#define GPIO_U300_CONFIG_BIAS_PULL_UP 0x1002 -/* Memory resource */ -static struct resource *memres; -static void __iomem *virtbase; -static struct device *gpiodev; +/* + * Drive modes for U300 GPIOs (output) + * + * GPIO_U300_CONFIG_DRIVE_PUSH_PULL: the GPIO will be driven actively high and + * low, this is the most typical case and is typically achieved with two + * active transistors on the output + * GPIO_U300_CONFIG_DRIVE_OPEN_DRAIN: the GPIO will be driven with open drain + * (open collector) which means it is usually wired with other output + * ports which are then pulled up with an external resistor + * GPIO_U300_CONFIG_DRIVE_OPEN_SOURCE: the GPIO will be driven with open drain + * (open emitter) which is the same as open drain mutatis mutandis but + * pulled to ground + */ +#define GPIO_U300_CONFIG_DRIVE_PUSH_PULL 0x2000 +#define GPIO_U300_CONFIG_DRIVE_OPEN_DRAIN 0x2001 +#define GPIO_U300_CONFIG_DRIVE_OPEN_SOURCE 0x2002 + +/* + * Register definitions for COH 901 335 variant + */ +#define U300_335_PORT_STRIDE (0x1C) +/* Port X Pin Data Register 32bit, this is both input and output (R/W) */ +#define U300_335_PXPDIR (0x00) +#define U300_335_PXPDOR (0x00) +/* Port X Pin Config Register 32bit (R/W) */ +#define U300_335_PXPCR (0x04) +/* This register layout is the same in both blocks */ +#define U300_GPIO_PXPCR_ALL_PINS_MODE_MASK (0x0000FFFFUL) +#define U300_GPIO_PXPCR_PIN_MODE_MASK (0x00000003UL) +#define U300_GPIO_PXPCR_PIN_MODE_SHIFT (0x00000002UL) +#define U300_GPIO_PXPCR_PIN_MODE_INPUT (0x00000000UL) +#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL (0x00000001UL) +#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN (0x00000002UL) +#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE (0x00000003UL) +/* Port X Interrupt Event Register 32bit (R/W) */ +#define U300_335_PXIEV (0x08) +/* Port X Interrupt Enable Register 32bit (R/W) */ +#define U300_335_PXIEN (0x0C) +/* Port X Interrupt Force Register 32bit (R/W) */ +#define U300_335_PXIFR (0x10) +/* Port X Interrupt Config Register 32bit (R/W) */ +#define U300_335_PXICR (0x14) +/* This register layout is the same in both blocks */ +#define U300_GPIO_PXICR_ALL_IRQ_CONFIG_MASK (0x000000FFUL) +#define U300_GPIO_PXICR_IRQ_CONFIG_MASK (0x00000001UL) +#define U300_GPIO_PXICR_IRQ_CONFIG_FALLING_EDGE (0x00000000UL) +#define U300_GPIO_PXICR_IRQ_CONFIG_RISING_EDGE (0x00000001UL) +/* Port X Pull-up Enable Register 32bit (R/W) */ +#define U300_335_PXPER (0x18) +/* This register layout is the same in both blocks */ +#define U300_GPIO_PXPER_ALL_PULL_UP_DISABLE_MASK (0x000000FFUL) +#define U300_GPIO_PXPER_PULL_UP_DISABLE (0x00000001UL) +/* Control Register 32bit (R/W) */ +#define U300_335_CR (0x54) +#define U300_335_CR_BLOCK_CLOCK_ENABLE (0x00000001UL) + +/* + * Register definitions for COH 901 571 / 3 variant + */ +#define U300_571_PORT_STRIDE (0x30) +/* + * Control Register 32bit (R/W) + * bit 15-9 (mask 0x0000FE00) contains the number of cores. 8*cores + * gives the number of GPIO pins. + * bit 8-2 (mask 0x000001FC) contains the core version ID. + */ +#define U300_571_CR (0x00) +#define U300_571_CR_SYNC_SEL_ENABLE (0x00000002UL) +#define U300_571_CR_BLOCK_CLKRQ_ENABLE (0x00000001UL) +/* + * These registers have the same layout and function as the corresponding + * COH 901 335 registers, just at different offset. + */ +#define U300_571_PXPDIR (0x04) +#define U300_571_PXPDOR (0x08) +#define U300_571_PXPCR (0x0C) +#define U300_571_PXPER (0x10) +#define U300_571_PXIEV (0x14) +#define U300_571_PXIEN (0x18) +#define U300_571_PXIFR (0x1C) +#define U300_571_PXICR (0x20) + +/* 8 bits per port, no version has more than 7 ports */ +#define U300_GPIO_PINS_PER_PORT 8 +#define U300_GPIO_MAX (U300_GPIO_PINS_PER_PORT * 7) + +struct u300_gpio { + struct gpio_chip chip; + struct list_head port_list; + struct clk *clk; + struct resource *memres; + void __iomem *base; + struct device *dev; + int irq_base; + u32 stride; + /* Register offsets */ + u32 pcr; + u32 dor; + u32 dir; + u32 per; + u32 icr; + u32 ien; + u32 iev; +}; struct u300_gpio_port { - const char *name; + struct list_head node; + struct u300_gpio *gpio; + char name[8]; int irq; int number; + u8 toggle_edge_mode; }; +/* + * Macro to expand to read a specific register found in the "gpio" + * struct. It requires the struct u300_gpio *gpio variable to exist in + * its context. It calculates the port offset from the given pin + * offset, muliplies by the port stride and adds the register offset + * so it provides a pointer to the desired register. + */ +#define U300_PIN_REG(pin, reg) \ + (gpio->base + (pin >> 3) * gpio->stride + gpio->reg) -static struct u300_gpio_port gpio_ports[] = { - { - .name = "gpio0", - .number = 0, - }, - { - .name = "gpio1", - .number = 1, - }, - { - .name = "gpio2", - .number = 2, - }, -#ifdef U300_COH901571_3 - { - .name = "gpio3", - .number = 3, - }, - { - .name = "gpio4", - .number = 4, - }, -#ifdef CONFIG_MACH_U300_BS335 - { - .name = "gpio5", - .number = 5, - }, - { - .name = "gpio6", - .number = 6, - }, -#endif -#endif +/* + * Provides a bitmask for a specific gpio pin inside an 8-bit GPIO + * register. + */ +#define U300_PIN_BIT(pin) \ + (1 << (pin & 0x07)) +struct u300_gpio_confdata { + u16 bias_mode; + bool output; + int outval; }; +/* BS335 has seven ports of 8 bits each = GPIO pins 0..55 */ +#define BS335_GPIO_NUM_PORTS 7 +/* BS365 has five ports of 8 bits each = GPIO pins 0..39 */ +#define BS365_GPIO_NUM_PORTS 5 -#ifdef U300_COH901571_3 +#define U300_FLOATING_INPUT { \ + .bias_mode = GPIO_U300_CONFIG_BIAS_FLOAT, \ + .output = false, \ +} -/* Default input value */ -#define DEFAULT_OUTPUT_LOW 0 -#define DEFAULT_OUTPUT_HIGH 1 +#define U300_PULL_UP_INPUT { \ + .bias_mode = GPIO_U300_CONFIG_BIAS_PULL_UP, \ + .output = false, \ +} -/* GPIO Pull-Up status */ -#define DISABLE_PULL_UP 0 -#define ENABLE_PULL_UP 1 +#define U300_OUTPUT_LOW { \ + .output = true, \ + .outval = 0, \ +} -#define GPIO_NOT_USED 0 -#define GPIO_IN 1 -#define GPIO_OUT 2 +#define U300_OUTPUT_HIGH { \ + .output = true, \ + .outval = 1, \ +} -struct u300_gpio_configuration_data { - unsigned char pin_usage; - unsigned char default_output_value; - unsigned char pull_up; -}; /* Initial configuration */ -const struct u300_gpio_configuration_data -u300_gpio_config[U300_GPIO_NUM_PORTS][U300_GPIO_PINS_PER_PORT] = { -#ifdef CONFIG_MACH_U300_BS335 +static const struct __initdata u300_gpio_confdata +bs335_gpio_config[BS335_GPIO_NUM_PORTS][U300_GPIO_PINS_PER_PORT] = { /* Port 0, pins 0-7 */ { - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_OUT, DEFAULT_OUTPUT_HIGH, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP} + U300_FLOATING_INPUT, + U300_OUTPUT_HIGH, + U300_FLOATING_INPUT, + U300_OUTPUT_LOW, + U300_OUTPUT_LOW, + U300_OUTPUT_LOW, + U300_OUTPUT_LOW, + U300_OUTPUT_LOW, }, /* Port 1, pins 0-7 */ { - {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_OUT, DEFAULT_OUTPUT_HIGH, DISABLE_PULL_UP}, - {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP} + U300_OUTPUT_LOW, + U300_OUTPUT_LOW, + U300_OUTPUT_LOW, + U300_PULL_UP_INPUT, + U300_FLOATING_INPUT, + U300_OUTPUT_HIGH, + U300_OUTPUT_LOW, + U300_OUTPUT_LOW, }, /* Port 2, pins 0-7 */ { - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP}, - {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP} + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, + U300_OUTPUT_LOW, + U300_PULL_UP_INPUT, + U300_OUTPUT_LOW, + U300_PULL_UP_INPUT, }, /* Port 3, pins 0-7 */ { - {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP}, - {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP} + U300_PULL_UP_INPUT, + U300_OUTPUT_LOW, + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, }, /* Port 4, pins 0-7 */ { - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP} + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, }, /* Port 5, pins 0-7 */ { - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP} + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, }, /* Port 6, pind 0-7 */ { - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP} + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, } -#endif +}; -#ifdef CONFIG_MACH_U300_BS365 +static const struct __initdata u300_gpio_confdata +bs365_gpio_config[BS365_GPIO_NUM_PORTS][U300_GPIO_PINS_PER_PORT] = { /* Port 0, pins 0-7 */ { - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP} + U300_FLOATING_INPUT, + U300_OUTPUT_LOW, + U300_FLOATING_INPUT, + U300_OUTPUT_LOW, + U300_OUTPUT_LOW, + U300_OUTPUT_LOW, + U300_PULL_UP_INPUT, + U300_FLOATING_INPUT, }, /* Port 1, pins 0-7 */ { - {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_OUT, DEFAULT_OUTPUT_HIGH, DISABLE_PULL_UP}, - {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP} + U300_OUTPUT_LOW, + U300_FLOATING_INPUT, + U300_OUTPUT_LOW, + U300_FLOATING_INPUT, + U300_FLOATING_INPUT, + U300_OUTPUT_HIGH, + U300_OUTPUT_LOW, + U300_OUTPUT_LOW, }, /* Port 2, pins 0-7 */ { - {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP}, - {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP} + U300_FLOATING_INPUT, + U300_PULL_UP_INPUT, + U300_OUTPUT_LOW, + U300_OUTPUT_LOW, + U300_PULL_UP_INPUT, + U300_PULL_UP_INPUT, + U300_PULL_UP_INPUT, + U300_PULL_UP_INPUT, }, /* Port 3, pins 0-7 */ { - {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP} + U300_PULL_UP_INPUT, + U300_PULL_UP_INPUT, + U300_PULL_UP_INPUT, + U300_PULL_UP_INPUT, + U300_PULL_UP_INPUT, + U300_PULL_UP_INPUT, + U300_PULL_UP_INPUT, + U300_PULL_UP_INPUT, }, /* Port 4, pins 0-7 */ { - {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP}, - {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP}, + U300_PULL_UP_INPUT, + U300_PULL_UP_INPUT, + U300_PULL_UP_INPUT, + U300_PULL_UP_INPUT, /* These 4 pins doesn't exist on DB3210 */ - {GPIO_OUT, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP}, - {GPIO_OUT, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP}, - {GPIO_OUT, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP}, - {GPIO_OUT, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP} + U300_OUTPUT_LOW, + U300_OUTPUT_LOW, + U300_OUTPUT_LOW, + U300_OUTPUT_LOW, } -#endif }; -#endif - -/* No users == we can power down GPIO */ -static int gpio_users; - -struct gpio_struct { - int (*callback)(void *); - void *data; - int users; -}; - -static struct gpio_struct gpio_pin[U300_GPIO_MAX]; - -/* - * Let drivers register callback in order to get notified when there is - * an interrupt on the gpio pin +/** + * to_u300_gpio() - get the pointer to u300_gpio + * @chip: the gpio chip member of the structure u300_gpio */ -int gpio_register_callback(unsigned gpio, int (*func)(void *arg), void *data) +static inline struct u300_gpio *to_u300_gpio(struct gpio_chip *chip) { - if (gpio_pin[gpio].callback) - dev_warn(gpiodev, "%s: WARNING: callback already " - "registered for gpio pin#%d\n", __func__, gpio); - gpio_pin[gpio].callback = func; - gpio_pin[gpio].data = data; - - return 0; + return container_of(chip, struct u300_gpio, chip); } -EXPORT_SYMBOL(gpio_register_callback); -int gpio_unregister_callback(unsigned gpio) +static int u300_gpio_get(struct gpio_chip *chip, unsigned offset) { - if (!gpio_pin[gpio].callback) - dev_warn(gpiodev, "%s: WARNING: callback already " - "unregistered for gpio pin#%d\n", __func__, gpio); - gpio_pin[gpio].callback = NULL; - gpio_pin[gpio].data = NULL; + struct u300_gpio *gpio = to_u300_gpio(chip); - return 0; + return readl(U300_PIN_REG(offset, dir)) & U300_PIN_BIT(offset); } -EXPORT_SYMBOL(gpio_unregister_callback); -/* Non-zero means valid */ -int gpio_is_valid(int number) +static void u300_gpio_set(struct gpio_chip *chip, unsigned offset, int value) { - if (number >= 0 && - number < (U300_GPIO_NUM_PORTS * U300_GPIO_PINS_PER_PORT)) - return 1; - return 0; -} -EXPORT_SYMBOL(gpio_is_valid); + struct u300_gpio *gpio = to_u300_gpio(chip); + unsigned long flags; + u32 val; -int gpio_request(unsigned gpio, const char *label) -{ - if (gpio_pin[gpio].users) - return -EINVAL; - else - gpio_pin[gpio].users++; + local_irq_save(flags); - gpio_users++; + val = readl(U300_PIN_REG(offset, dor)); + if (value) + writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, dor)); + else + writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, dor)); - return 0; + local_irq_restore(flags); } -EXPORT_SYMBOL(gpio_request); -void gpio_free(unsigned gpio) +static int u300_gpio_direction_input(struct gpio_chip *chip, unsigned offset) { - gpio_users--; - gpio_pin[gpio].users--; - if (unlikely(gpio_pin[gpio].users < 0)) { - dev_warn(gpiodev, "warning: gpio#%d release mismatch\n", - gpio); - gpio_pin[gpio].users = 0; - } - - return; -} -EXPORT_SYMBOL(gpio_free); + struct u300_gpio *gpio = to_u300_gpio(chip); + unsigned long flags; + u32 val; -/* This returns zero or nonzero */ -int gpio_get_value(unsigned gpio) -{ - return readl(virtbase + U300_GPIO_PXPDIR + - PIN_TO_PORT(gpio) * U300_GPIO_PORTX_SPACING) & (1 << (gpio & 0x07)); + local_irq_save(flags); + val = readl(U300_PIN_REG(offset, pcr)); + /* Mask out this pin, note 2 bits per setting */ + val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK << ((offset & 0x07) << 1)); + writel(val, U300_PIN_REG(offset, pcr)); + local_irq_restore(flags); + return 0; } -EXPORT_SYMBOL(gpio_get_value); -/* - * We hope that the compiler will optimize away the unused branch - * in case "value" is a constant - */ -void gpio_set_value(unsigned gpio, int value) +static int u300_gpio_direction_output(struct gpio_chip *chip, unsigned offset, + int value) { - u32 val; + struct u300_gpio *gpio = to_u300_gpio(chip); unsigned long flags; + u32 oldmode; + u32 val; local_irq_save(flags); - if (value) { - /* set */ - val = readl(virtbase + U300_GPIO_PXPDOR + - PIN_TO_PORT(gpio) * U300_GPIO_PORTX_SPACING) - & (1 << (gpio & 0x07)); - writel(val | (1 << (gpio & 0x07)), virtbase + - U300_GPIO_PXPDOR + - PIN_TO_PORT(gpio) * U300_GPIO_PORTX_SPACING); - } else { - /* clear */ - val = readl(virtbase + U300_GPIO_PXPDOR + - PIN_TO_PORT(gpio) * U300_GPIO_PORTX_SPACING) - & (1 << (gpio & 0x07)); - writel(val & ~(1 << (gpio & 0x07)), virtbase + - U300_GPIO_PXPDOR + - PIN_TO_PORT(gpio) * U300_GPIO_PORTX_SPACING); + val = readl(U300_PIN_REG(offset, pcr)); + /* + * Drive mode must be set by the special mode set function, set + * push/pull mode by default if no mode has been selected. + */ + oldmode = val & (U300_GPIO_PXPCR_PIN_MODE_MASK << + ((offset & 0x07) << 1)); + /* mode = 0 means input, else some mode is already set */ + if (oldmode == 0) { + val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK << + ((offset & 0x07) << 1)); + val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL + << ((offset & 0x07) << 1)); + writel(val, U300_PIN_REG(offset, pcr)); } + u300_gpio_set(chip, offset, value); local_irq_restore(flags); + return 0; } -EXPORT_SYMBOL(gpio_set_value); -int gpio_direction_input(unsigned gpio) +static int u300_gpio_to_irq(struct gpio_chip *chip, unsigned offset) { + struct u300_gpio *gpio = to_u300_gpio(chip); + int retirq = gpio->irq_base + offset; + + dev_dbg(gpio->dev, "request IRQ for GPIO %d, return %d\n", offset, + retirq); + return retirq; +} + +static int u300_gpio_config(struct gpio_chip *chip, unsigned offset, + u16 param, unsigned long *data) +{ + struct u300_gpio *gpio = to_u300_gpio(chip); unsigned long flags; u32 val; - if (gpio > U300_GPIO_MAX) - return -EINVAL; - local_irq_save(flags); - val = readl(virtbase + U300_GPIO_PXPCR + PIN_TO_PORT(gpio) * - U300_GPIO_PORTX_SPACING); - /* Mask out this pin*/ - val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK << ((gpio & 0x07) << 1)); - /* This is not needed since it sets the bits to zero.*/ - /* val |= (U300_GPIO_PXPCR_PIN_MODE_INPUT << (gpio*2)); */ - writel(val, virtbase + U300_GPIO_PXPCR + PIN_TO_PORT(gpio) * - U300_GPIO_PORTX_SPACING); + switch (param) { + case GPIO_U300_CONFIG_BIAS_UNKNOWN: + case GPIO_U300_CONFIG_BIAS_FLOAT: + val = readl(U300_PIN_REG(offset, per)); + writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, per)); + break; + case GPIO_U300_CONFIG_BIAS_PULL_UP: + val = readl(U300_PIN_REG(offset, per)); + writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, per)); + break; + case GPIO_U300_CONFIG_DRIVE_PUSH_PULL: + val = readl(U300_PIN_REG(offset, pcr)); + val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK + << ((offset & 0x07) << 1)); + val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL + << ((offset & 0x07) << 1)); + writel(val, U300_PIN_REG(offset, pcr)); + break; + case GPIO_U300_CONFIG_DRIVE_OPEN_DRAIN: + val = readl(U300_PIN_REG(offset, pcr)); + val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK + << ((offset & 0x07) << 1)); + val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN + << ((offset & 0x07) << 1)); + writel(val, U300_PIN_REG(offset, pcr)); + break; + case GPIO_U300_CONFIG_DRIVE_OPEN_SOURCE: + val = readl(U300_PIN_REG(offset, pcr)); + val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK + << ((offset & 0x07) << 1)); + val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE + << ((offset & 0x07) << 1)); + writel(val, U300_PIN_REG(offset, pcr)); + break; + default: + local_irq_restore(flags); + dev_err(gpio->dev, "illegal configuration requested\n"); + return -EINVAL; + } local_irq_restore(flags); return 0; } -EXPORT_SYMBOL(gpio_direction_input); -int gpio_direction_output(unsigned gpio, int value) +static struct gpio_chip u300_gpio_chip = { + .label = "u300-gpio-chip", + .owner = THIS_MODULE, + .get = u300_gpio_get, + .set = u300_gpio_set, + .direction_input = u300_gpio_direction_input, + .direction_output = u300_gpio_direction_output, + .to_irq = u300_gpio_to_irq, +}; + +static void u300_toggle_trigger(struct u300_gpio *gpio, unsigned offset) { - unsigned long flags; u32 val; - if (gpio > U300_GPIO_MAX) - return -EINVAL; - - local_irq_save(flags); - val = readl(virtbase + U300_GPIO_PXPCR + PIN_TO_PORT(gpio) * - U300_GPIO_PORTX_SPACING); - /* Mask out this pin */ - val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK << ((gpio & 0x07) << 1)); - /* - * FIXME: configure for push/pull, open drain or open source per pin - * in setup. The current driver will only support push/pull. - */ - val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL - << ((gpio & 0x07) << 1)); - writel(val, virtbase + U300_GPIO_PXPCR + PIN_TO_PORT(gpio) * - U300_GPIO_PORTX_SPACING); - gpio_set_value(gpio, value); - local_irq_restore(flags); - return 0; + val = readl(U300_PIN_REG(offset, icr)); + /* Set mode depending on state */ + if (u300_gpio_get(&gpio->chip, offset)) { + /* High now, let's trigger on falling edge next then */ + writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, icr)); + dev_dbg(gpio->dev, "next IRQ on falling edge on pin %d\n", + offset); + } else { + /* Low now, let's trigger on rising edge next then */ + writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, icr)); + dev_dbg(gpio->dev, "next IRQ on rising edge on pin %d\n", + offset); + } } -EXPORT_SYMBOL(gpio_direction_output); -/* - * Enable an IRQ, edge is rising edge (!= 0) or falling edge (==0). - */ -void enable_irq_on_gpio_pin(unsigned gpio, int edge) +static int u300_gpio_irq_type(struct irq_data *d, unsigned trigger) { + struct u300_gpio_port *port = irq_data_get_irq_chip_data(d); + struct u300_gpio *gpio = port->gpio; + int offset = d->irq - gpio->irq_base; u32 val; - unsigned long flags; - local_irq_save(flags); - val = readl(virtbase + U300_GPIO_PXIEN + PIN_TO_PORT(gpio) * - U300_GPIO_PORTX_SPACING); - val |= (1 << (gpio & 0x07)); - writel(val, virtbase + U300_GPIO_PXIEN + PIN_TO_PORT(gpio) * - U300_GPIO_PORTX_SPACING); - val = readl(virtbase + U300_GPIO_PXICR + PIN_TO_PORT(gpio) * - U300_GPIO_PORTX_SPACING); - if (edge) - val |= (1 << (gpio & 0x07)); - else - val &= ~(1 << (gpio & 0x07)); - writel(val, virtbase + U300_GPIO_PXICR + PIN_TO_PORT(gpio) * - U300_GPIO_PORTX_SPACING); - local_irq_restore(flags); + if ((trigger & IRQF_TRIGGER_RISING) && + (trigger & IRQF_TRIGGER_FALLING)) { + /* + * The GPIO block can only trigger on falling OR rising edges, + * not both. So we need to toggle the mode whenever the pin + * goes from one state to the other with a special state flag + */ + dev_dbg(gpio->dev, + "trigger on both rising and falling edge on pin %d\n", + offset); + port->toggle_edge_mode |= U300_PIN_BIT(offset); + u300_toggle_trigger(gpio, offset); + } else if (trigger & IRQF_TRIGGER_RISING) { + dev_dbg(gpio->dev, "trigger on rising edge on pin %d\n", + offset); + val = readl(U300_PIN_REG(offset, icr)); + writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, icr)); + port->toggle_edge_mode &= ~U300_PIN_BIT(offset); + } else if (trigger & IRQF_TRIGGER_FALLING) { + dev_dbg(gpio->dev, "trigger on falling edge on pin %d\n", + offset); + val = readl(U300_PIN_REG(offset, icr)); + writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, icr)); + port->toggle_edge_mode &= ~U300_PIN_BIT(offset); + } + + return 0; } -EXPORT_SYMBOL(enable_irq_on_gpio_pin); -void disable_irq_on_gpio_pin(unsigned gpio) +static void u300_gpio_irq_enable(struct irq_data *d) { + struct u300_gpio_port *port = irq_data_get_irq_chip_data(d); + struct u300_gpio *gpio = port->gpio; + int offset = d->irq - gpio->irq_base; u32 val; unsigned long flags; local_irq_save(flags); - val = readl(virtbase + U300_GPIO_PXIEN + PIN_TO_PORT(gpio) * - U300_GPIO_PORTX_SPACING); - val &= ~(1 << (gpio & 0x07)); - writel(val, virtbase + U300_GPIO_PXIEN + PIN_TO_PORT(gpio) * - U300_GPIO_PORTX_SPACING); + val = readl(U300_PIN_REG(offset, ien)); + writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, ien)); local_irq_restore(flags); } -EXPORT_SYMBOL(disable_irq_on_gpio_pin); -/* Enable (value == 0) or disable (value == 1) internal pullup */ -void gpio_pullup(unsigned gpio, int value) +static void u300_gpio_irq_disable(struct irq_data *d) { + struct u300_gpio_port *port = irq_data_get_irq_chip_data(d); + struct u300_gpio *gpio = port->gpio; + int offset = d->irq - gpio->irq_base; u32 val; unsigned long flags; local_irq_save(flags); - if (value) { - val = readl(virtbase + U300_GPIO_PXPER + PIN_TO_PORT(gpio) * - U300_GPIO_PORTX_SPACING); - writel(val | (1 << (gpio & 0x07)), virtbase + U300_GPIO_PXPER + - PIN_TO_PORT(gpio) * U300_GPIO_PORTX_SPACING); - } else { - val = readl(virtbase + U300_GPIO_PXPER + PIN_TO_PORT(gpio) * - U300_GPIO_PORTX_SPACING); - writel(val & ~(1 << (gpio & 0x07)), virtbase + U300_GPIO_PXPER + - PIN_TO_PORT(gpio) * U300_GPIO_PORTX_SPACING); - } + val = readl(U300_PIN_REG(offset, ien)); + writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, ien)); local_irq_restore(flags); } -EXPORT_SYMBOL(gpio_pullup); -static irqreturn_t gpio_irq_handler(int irq, void *dev_id) +static struct irq_chip u300_gpio_irqchip = { + .name = "u300-gpio-irqchip", + .irq_enable = u300_gpio_irq_enable, + .irq_disable = u300_gpio_irq_disable, + .irq_set_type = u300_gpio_irq_type, + +}; + +static void u300_gpio_irq_handler(unsigned irq, struct irq_desc *desc) { - struct u300_gpio_port *port = dev_id; - u32 val; - int pin; + struct u300_gpio_port *port = irq_get_handler_data(irq); + struct u300_gpio *gpio = port->gpio; + int pinoffset = port->number << 3; /* get the right stride */ + unsigned long val; + desc->irq_data.chip->irq_ack(&desc->irq_data); /* Read event register */ - val = readl(virtbase + U300_GPIO_PXIEV + port->number * - U300_GPIO_PORTX_SPACING); - /* Mask with enable register */ - val &= readl(virtbase + U300_GPIO_PXIEV + port->number * - U300_GPIO_PORTX_SPACING); + val = readl(U300_PIN_REG(pinoffset, iev)); /* Mask relevant bits */ - val &= U300_GPIO_PXIEV_ALL_IRQ_EVENT_MASK; + val &= 0xFFU; /* 8 bits per port */ /* ACK IRQ (clear event) */ - writel(val, virtbase + U300_GPIO_PXIEV + port->number * - U300_GPIO_PORTX_SPACING); - /* Print message */ - while (val != 0) { - unsigned gpio; - - pin = __ffs(val); - /* mask off this pin */ - val &= ~(1 << pin); - gpio = (port->number << 3) + pin; - - if (gpio_pin[gpio].callback) - (void)gpio_pin[gpio].callback(gpio_pin[gpio].data); - else - dev_dbg(gpiodev, "stray GPIO IRQ on line %d\n", - gpio); + writel(val, U300_PIN_REG(pinoffset, iev)); + + /* Call IRQ handler */ + if (val != 0) { + int irqoffset; + + for_each_set_bit(irqoffset, &val, U300_GPIO_PINS_PER_PORT) { + int pin_irq = gpio->irq_base + (port->number << 3) + + irqoffset; + int offset = pinoffset + irqoffset; + + dev_dbg(gpio->dev, "GPIO IRQ %d on pin %d\n", + pin_irq, offset); + generic_handle_irq(pin_irq); + /* + * Triggering IRQ on both rising and falling edge + * needs mockery + */ + if (port->toggle_edge_mode & U300_PIN_BIT(offset)) + u300_toggle_trigger(gpio, offset); + } } - return IRQ_HANDLED; + + desc->irq_data.chip->irq_unmask(&desc->irq_data); } -static void gpio_set_initial_values(void) +static void __init u300_gpio_init_pin(struct u300_gpio *gpio, + int offset, + const struct u300_gpio_confdata *conf) { -#ifdef U300_COH901571_3 - int i, j; - unsigned long flags; - u32 val; + /* Set mode: input or output */ + if (conf->output) { + u300_gpio_direction_output(&gpio->chip, offset, conf->outval); - /* Write default values to all pins */ - for (i = 0; i < U300_GPIO_NUM_PORTS; i++) { - val = 0; - for (j = 0; j < 8; j++) - val |= (u32) (u300_gpio_config[i][j].default_output_value != DEFAULT_OUTPUT_LOW) << j; - local_irq_save(flags); - writel(val, virtbase + U300_GPIO_PXPDOR + i * U300_GPIO_PORTX_SPACING); - local_irq_restore(flags); + /* Deactivate bias mode for output */ + u300_gpio_config(&gpio->chip, offset, + GPIO_U300_CONFIG_BIAS_FLOAT, + NULL); + + /* Set drive mode for output */ + u300_gpio_config(&gpio->chip, offset, + GPIO_U300_CONFIG_DRIVE_PUSH_PULL, NULL); + + dev_dbg(gpio->dev, "set up pin %d as output, value: %d\n", + offset, conf->outval); + } else { + u300_gpio_direction_input(&gpio->chip, offset); + + /* Always set output low on input pins */ + u300_gpio_set(&gpio->chip, offset, 0); + + /* Set bias mode for input */ + u300_gpio_config(&gpio->chip, offset, conf->bias_mode, NULL); + + dev_dbg(gpio->dev, "set up pin %d as input, bias: %04x\n", + offset, conf->bias_mode); } +} - /* - * Put all pins that are set to either 'GPIO_OUT' or 'GPIO_NOT_USED' - * to output and 'GPIO_IN' to input for each port. And initialize - * default value on outputs. - */ - for (i = 0; i < U300_GPIO_NUM_PORTS; i++) { - for (j = 0; j < U300_GPIO_PINS_PER_PORT; j++) { - local_irq_save(flags); - val = readl(virtbase + U300_GPIO_PXPCR + - i * U300_GPIO_PORTX_SPACING); - /* Mask out this pin */ - val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK << (j << 1)); - - if (u300_gpio_config[i][j].pin_usage != GPIO_IN) - val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL << (j << 1)); - writel(val, virtbase + U300_GPIO_PXPCR + - i * U300_GPIO_PORTX_SPACING); - local_irq_restore(flags); +static void __init u300_gpio_init_coh901571(struct u300_gpio *gpio, + struct u300_gpio_platform *plat) +{ + int i, j; + + /* Write default config and values to all pins */ + for (i = 0; i < plat->ports; i++) { + for (j = 0; j < 8; j++) { + const struct u300_gpio_confdata *conf; + int offset = (i*8) + j; + + if (plat->variant == U300_GPIO_COH901571_3_BS335) + conf = &bs335_gpio_config[i][j]; + else if (plat->variant == U300_GPIO_COH901571_3_BS365) + conf = &bs365_gpio_config[i][j]; + else + break; + + u300_gpio_init_pin(gpio, offset, conf); } } +} - /* Enable or disable the internal pull-ups in the GPIO ASIC block */ - for (i = 0; i < U300_GPIO_MAX; i++) { - val = 0; - for (j = 0; j < 8; j++) - val |= (u32)((u300_gpio_config[i][j].pull_up == DISABLE_PULL_UP) << j); - local_irq_save(flags); - writel(val, virtbase + U300_GPIO_PXPER + i * U300_GPIO_PORTX_SPACING); - local_irq_restore(flags); +static inline void u300_gpio_free_ports(struct u300_gpio *gpio) +{ + struct u300_gpio_port *port; + struct list_head *p, *n; + + list_for_each_safe(p, n, &gpio->port_list) { + port = list_entry(p, struct u300_gpio_port, node); + list_del(&port->node); + free_irq(port->irq, port); + kfree(port); } -#endif } -static int __init gpio_probe(struct platform_device *pdev) +static int __init u300_gpio_probe(struct platform_device *pdev) { - u32 val; + struct u300_gpio_platform *plat = dev_get_platdata(&pdev->dev); + struct u300_gpio *gpio; int err = 0; + int portno; + u32 val; + u32 ifr; int i; - int num_irqs; - gpiodev = &pdev->dev; - memset(gpio_pin, 0, sizeof(gpio_pin)); + gpio = kzalloc(sizeof(struct u300_gpio), GFP_KERNEL); + if (gpio == NULL) { + dev_err(&pdev->dev, "failed to allocate memory\n"); + return -ENOMEM; + } + + gpio->chip = u300_gpio_chip; + gpio->chip.ngpio = plat->ports * U300_GPIO_PINS_PER_PORT; + gpio->irq_base = plat->gpio_irq_base; + gpio->chip.dev = &pdev->dev; + gpio->chip.base = plat->gpio_base; + gpio->dev = &pdev->dev; /* Get GPIO clock */ - clk = clk_get(&pdev->dev, NULL); - if (IS_ERR(clk)) { - err = PTR_ERR(clk); - dev_err(gpiodev, "could not get GPIO clock\n"); + gpio->clk = clk_get(gpio->dev, NULL); + if (IS_ERR(gpio->clk)) { + err = PTR_ERR(gpio->clk); + dev_err(gpio->dev, "could not get GPIO clock\n"); goto err_no_clk; } - err = clk_enable(clk); + err = clk_enable(gpio->clk); if (err) { - dev_err(gpiodev, "could not enable GPIO clock\n"); + dev_err(gpio->dev, "could not enable GPIO clock\n"); goto err_no_clk_enable; } - memres = platform_get_resource(pdev, IORESOURCE_MEM, 0); - if (!memres) + gpio->memres = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!gpio->memres) { + dev_err(gpio->dev, "could not get GPIO memory resource\n"); + err = -ENODEV; goto err_no_resource; + } - if (!request_mem_region(memres->start, resource_size(memres), + if (!request_mem_region(gpio->memres->start, + resource_size(gpio->memres), "GPIO Controller")) { err = -ENODEV; goto err_no_ioregion; } - virtbase = ioremap(memres->start, resource_size(memres)); - if (!virtbase) { + gpio->base = ioremap(gpio->memres->start, resource_size(gpio->memres)); + if (!gpio->base) { err = -ENOMEM; goto err_no_ioremap; } - dev_info(gpiodev, "remapped 0x%08x to %p\n", - memres->start, virtbase); - -#ifdef U300_COH901335 - dev_info(gpiodev, "initializing GPIO Controller COH 901 335\n"); - /* Turn on the GPIO block */ - writel(U300_GPIO_CR_BLOCK_CLOCK_ENABLE, virtbase + U300_GPIO_CR); -#endif - -#ifdef U300_COH901571_3 - dev_info(gpiodev, "initializing GPIO Controller COH 901 571/3\n"); - val = readl(virtbase + U300_GPIO_CR); - dev_info(gpiodev, "COH901571/3 block version: %d, " \ - "number of cores: %d\n", - ((val & 0x0000FE00) >> 9), - ((val & 0x000001FC) >> 2)); - writel(U300_GPIO_CR_BLOCK_CLKRQ_ENABLE, virtbase + U300_GPIO_CR); -#endif - - gpio_set_initial_values(); - - for (num_irqs = 0 ; num_irqs < U300_GPIO_NUM_PORTS; num_irqs++) { - - gpio_ports[num_irqs].irq = - platform_get_irq_byname(pdev, - gpio_ports[num_irqs].name); - - err = request_irq(gpio_ports[num_irqs].irq, - gpio_irq_handler, IRQF_DISABLED, - gpio_ports[num_irqs].name, - &gpio_ports[num_irqs]); - if (err) { - dev_err(gpiodev, "cannot allocate IRQ for %s!\n", - gpio_ports[num_irqs].name); - goto err_no_irq; + + if (plat->variant == U300_GPIO_COH901335) { + dev_info(gpio->dev, + "initializing GPIO Controller COH 901 335\n"); + gpio->stride = U300_335_PORT_STRIDE; + gpio->pcr = U300_335_PXPCR; + gpio->dor = U300_335_PXPDOR; + gpio->dir = U300_335_PXPDIR; + gpio->per = U300_335_PXPER; + gpio->icr = U300_335_PXICR; + gpio->ien = U300_335_PXIEN; + gpio->iev = U300_335_PXIEV; + ifr = U300_335_PXIFR; + + /* Turn on the GPIO block */ + writel(U300_335_CR_BLOCK_CLOCK_ENABLE, + gpio->base + U300_335_CR); + } else if (plat->variant == U300_GPIO_COH901571_3_BS335 || + plat->variant == U300_GPIO_COH901571_3_BS365) { + dev_info(gpio->dev, + "initializing GPIO Controller COH 901 571/3\n"); + gpio->stride = U300_571_PORT_STRIDE; + gpio->pcr = U300_571_PXPCR; + gpio->dor = U300_571_PXPDOR; + gpio->dir = U300_571_PXPDIR; + gpio->per = U300_571_PXPER; + gpio->icr = U300_571_PXICR; + gpio->ien = U300_571_PXIEN; + gpio->iev = U300_571_PXIEV; + ifr = U300_571_PXIFR; + + val = readl(gpio->base + U300_571_CR); + dev_info(gpio->dev, "COH901571/3 block version: %d, " \ + "number of cores: %d totalling %d pins\n", + ((val & 0x000001FC) >> 2), + ((val & 0x0000FE00) >> 9), + ((val & 0x0000FE00) >> 9) * 8); + writel(U300_571_CR_BLOCK_CLKRQ_ENABLE, + gpio->base + U300_571_CR); + u300_gpio_init_coh901571(gpio, plat); + } else { + dev_err(gpio->dev, "unknown block variant\n"); + err = -ENODEV; + goto err_unknown_variant; + } + + /* Add each port with its IRQ separately */ + INIT_LIST_HEAD(&gpio->port_list); + for (portno = 0 ; portno < plat->ports; portno++) { + struct u300_gpio_port *port = + kmalloc(sizeof(struct u300_gpio_port), GFP_KERNEL); + + if (!port) { + dev_err(gpio->dev, "out of memory\n"); + err = -ENOMEM; + goto err_no_port; } - /* Turns off PortX_irq_force */ - writel(0x0, virtbase + U300_GPIO_PXIFR + - num_irqs * U300_GPIO_PORTX_SPACING); + + snprintf(port->name, 8, "gpio%d", portno); + port->number = portno; + port->gpio = gpio; + + port->irq = platform_get_irq_byname(pdev, + port->name); + + dev_dbg(gpio->dev, "register IRQ %d for %s\n", port->irq, + port->name); + + irq_set_chained_handler(port->irq, u300_gpio_irq_handler); + irq_set_handler_data(port->irq, port); + + /* For each GPIO pin set the unique IRQ handler */ + for (i = 0; i < U300_GPIO_PINS_PER_PORT; i++) { + int irqno = gpio->irq_base + (portno << 3) + i; + + dev_dbg(gpio->dev, "handler for IRQ %d on %s\n", + irqno, port->name); + irq_set_chip_and_handler(irqno, &u300_gpio_irqchip, + handle_simple_irq); + set_irq_flags(irqno, IRQF_VALID); + irq_set_chip_data(irqno, port); + } + + /* Turns off irq force (test register) for this port */ + writel(0x0, gpio->base + portno * gpio->stride + ifr); + + list_add_tail(&port->node, &gpio->port_list); } + dev_dbg(gpio->dev, "initialized %d GPIO ports\n", portno); + + err = gpiochip_add(&gpio->chip); + if (err) { + dev_err(gpio->dev, "unable to add gpiochip: %d\n", err); + goto err_no_chip; + } + + platform_set_drvdata(pdev, gpio); return 0; - err_no_irq: - for (i = 0; i < num_irqs; i++) - free_irq(gpio_ports[i].irq, &gpio_ports[i]); - iounmap(virtbase); - err_no_ioremap: - release_mem_region(memres->start, resource_size(memres)); - err_no_ioregion: - err_no_resource: - clk_disable(clk); - err_no_clk_enable: - clk_put(clk); - err_no_clk: - dev_info(gpiodev, "module ERROR:%d\n", err); +err_no_chip: +err_no_port: + u300_gpio_free_ports(gpio); +err_unknown_variant: + iounmap(gpio->base); +err_no_ioremap: + release_mem_region(gpio->memres->start, resource_size(gpio->memres)); +err_no_ioregion: +err_no_resource: + clk_disable(gpio->clk); +err_no_clk_enable: + clk_put(gpio->clk); +err_no_clk: + kfree(gpio); + dev_info(&pdev->dev, "module ERROR:%d\n", err); return err; } -static int __exit gpio_remove(struct platform_device *pdev) +static int __exit u300_gpio_remove(struct platform_device *pdev) { - int i; + struct u300_gpio_platform *plat = dev_get_platdata(&pdev->dev); + struct u300_gpio *gpio = platform_get_drvdata(pdev); + int err; /* Turn off the GPIO block */ - writel(0x00000000U, virtbase + U300_GPIO_CR); - for (i = 0 ; i < U300_GPIO_NUM_PORTS; i++) - free_irq(gpio_ports[i].irq, &gpio_ports[i]); - iounmap(virtbase); - release_mem_region(memres->start, resource_size(memres)); - clk_disable(clk); - clk_put(clk); + if (plat->variant == U300_GPIO_COH901335) + writel(0x00000000U, gpio->base + U300_335_CR); + if (plat->variant == U300_GPIO_COH901571_3_BS335 || + plat->variant == U300_GPIO_COH901571_3_BS365) + writel(0x00000000U, gpio->base + U300_571_CR); + + err = gpiochip_remove(&gpio->chip); + if (err < 0) { + dev_err(gpio->dev, "unable to remove gpiochip: %d\n", err); + return err; + } + u300_gpio_free_ports(gpio); + iounmap(gpio->base); + release_mem_region(gpio->memres->start, + resource_size(gpio->memres)); + clk_disable(gpio->clk); + clk_put(gpio->clk); + platform_set_drvdata(pdev, NULL); + kfree(gpio); return 0; } -static struct platform_driver gpio_driver = { +static struct platform_driver u300_gpio_driver = { .driver = { .name = "u300-gpio", }, - .remove = __exit_p(gpio_remove), + .remove = __exit_p(u300_gpio_remove), }; static int __init u300_gpio_init(void) { - return platform_driver_probe(&gpio_driver, gpio_probe); + return platform_driver_probe(&u300_gpio_driver, u300_gpio_probe); } static void __exit u300_gpio_exit(void) { - platform_driver_unregister(&gpio_driver); + platform_driver_unregister(&u300_gpio_driver); } arch_initcall(u300_gpio_init); module_exit(u300_gpio_exit); MODULE_AUTHOR("Linus Walleij <linus.walleij@stericsson.com>"); - -#ifdef U300_COH901571_3 -MODULE_DESCRIPTION("ST-Ericsson AB COH 901 571/3 GPIO driver"); -#endif - -#ifdef U300_COH901335 -MODULE_DESCRIPTION("ST-Ericsson AB COH 901 335 GPIO driver"); -#endif - +MODULE_DESCRIPTION("ST-Ericsson AB COH 901 335/COH 901 571/3 GPIO driver"); MODULE_LICENSE("GPL"); diff --git a/drivers/i2c/busses/i2c-ixp2000.c b/drivers/i2c/busses/i2c-ixp2000.c index 5d8aed5ec21b..c01e9519f6c1 100644 --- a/drivers/i2c/busses/i2c-ixp2000.c +++ b/drivers/i2c/busses/i2c-ixp2000.c @@ -35,7 +35,7 @@ #include <linux/slab.h> #include <mach/hardware.h> /* Pick up IXP2000-specific bits */ -#include <mach/gpio.h> +#include <mach/gpio-ixp2000.h> static inline int ixp2000_scl_pin(void *data) { diff --git a/drivers/ide/at91_ide.c b/drivers/ide/at91_ide.c index 000a78e5246c..6dede8f366c5 100644 --- a/drivers/ide/at91_ide.c +++ b/drivers/ide/at91_ide.c @@ -28,7 +28,7 @@ #include <linux/platform_device.h> #include <mach/board.h> -#include <mach/gpio.h> +#include <asm/gpio.h> #include <mach/at91sam9_smc.h> #define DRV_NAME "at91_ide" diff --git a/drivers/input/keyboard/omap-keypad.c b/drivers/input/keyboard/omap-keypad.c index 33d0bdc837c0..323bcdfff248 100644 --- a/drivers/input/keyboard/omap-keypad.c +++ b/drivers/input/keyboard/omap-keypad.c @@ -35,7 +35,7 @@ #include <linux/mutex.h> #include <linux/errno.h> #include <linux/slab.h> -#include <mach/gpio.h> +#include <asm/gpio.h> #include <plat/keypad.h> #include <plat/menelaus.h> #include <asm/irq.h> diff --git a/drivers/mfd/menelaus.c b/drivers/mfd/menelaus.c index 9cee8e7f0bcb..af5d9d061371 100644 --- a/drivers/mfd/menelaus.c +++ b/drivers/mfd/menelaus.c @@ -44,7 +44,7 @@ #include <asm/mach/irq.h> -#include <mach/gpio.h> +#include <asm/gpio.h> #include <plat/menelaus.h> #define DRIVER_NAME "menelaus" diff --git a/drivers/mmc/host/omap.c b/drivers/mmc/host/omap.c index a6c329040140..2dba999caf2c 100644 --- a/drivers/mmc/host/omap.c +++ b/drivers/mmc/host/omap.c @@ -33,7 +33,7 @@ #include <plat/board.h> #include <plat/mmc.h> -#include <mach/gpio.h> +#include <asm/gpio.h> #include <plat/dma.h> #include <plat/mux.h> #include <plat/fpga.h> diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c index 18b0bd31de78..21b00cefae63 100644 --- a/drivers/mmc/host/sdhci-tegra.c +++ b/drivers/mmc/host/sdhci-tegra.c @@ -21,7 +21,9 @@ #include <linux/mmc/card.h> #include <linux/mmc/host.h> -#include <mach/gpio.h> +#include <asm/gpio.h> + +#include <mach/gpio-tegra.h> #include <mach/sdhci.h> #include "sdhci-pltfm.h" diff --git a/drivers/mtd/nand/ams-delta.c b/drivers/mtd/nand/ams-delta.c index 78017eb9318e..9e6b498c9beb 100644 --- a/drivers/mtd/nand/ams-delta.c +++ b/drivers/mtd/nand/ams-delta.c @@ -26,7 +26,7 @@ #include <asm/io.h> #include <mach/hardware.h> #include <asm/sizes.h> -#include <mach/gpio.h> +#include <asm/gpio.h> #include <plat/board-ams-delta.h> /* diff --git a/drivers/mtd/onenand/omap2.c b/drivers/mtd/onenand/omap2.c index a916dec29215..6a1d6d9a2df9 100644 --- a/drivers/mtd/onenand/omap2.c +++ b/drivers/mtd/onenand/omap2.c @@ -40,7 +40,7 @@ #include <asm/mach/flash.h> #include <plat/gpmc.h> #include <plat/onenand.h> -#include <mach/gpio.h> +#include <asm/gpio.h> #include <plat/dma.h> diff --git a/drivers/net/arm/at91_ether.c b/drivers/net/arm/at91_ether.c index 29dc43523cec..48b4ec121f7f 100644 --- a/drivers/net/arm/at91_ether.c +++ b/drivers/net/arm/at91_ether.c @@ -35,7 +35,7 @@ #include <asm/mach-types.h> #include <mach/at91rm9200_emac.h> -#include <mach/gpio.h> +#include <asm/gpio.h> #include <mach/board.h> #include "at91_ether.h" diff --git a/drivers/pcmcia/pxa2xx_vpac270.c b/drivers/pcmcia/pxa2xx_vpac270.c index e956f659089a..66ab92cf3105 100644 --- a/drivers/pcmcia/pxa2xx_vpac270.c +++ b/drivers/pcmcia/pxa2xx_vpac270.c @@ -17,7 +17,7 @@ #include <asm/mach-types.h> -#include <mach/gpio.h> +#include <asm/gpio.h> #include <mach/vpac270.h> #include "soc_common.h" diff --git a/drivers/spi/spi-atmel.c b/drivers/spi/spi-atmel.c index 82dee9a6c0de..d3bff424286f 100644 --- a/drivers/spi/spi-atmel.c +++ b/drivers/spi/spi-atmel.c @@ -22,7 +22,7 @@ #include <asm/io.h> #include <mach/board.h> -#include <mach/gpio.h> +#include <asm/gpio.h> #include <mach/cpu.h> /* SPI register offsets */ diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c index b922f5d2e61e..caba6730a943 100644 --- a/drivers/tty/serial/atmel_serial.c +++ b/drivers/tty/serial/atmel_serial.c @@ -46,7 +46,7 @@ #ifdef CONFIG_ARM #include <mach/cpu.h> -#include <mach/gpio.h> +#include <asm/gpio.h> #endif #define PDC_BUFFER_SIZE 512 diff --git a/drivers/usb/host/ohci-pnx4008.c b/drivers/usb/host/ohci-pnx4008.c index 653d6a60edb5..d1b41933199e 100644 --- a/drivers/usb/host/ohci-pnx4008.c +++ b/drivers/usb/host/ohci-pnx4008.c @@ -26,7 +26,7 @@ #include <mach/platform.h> #include <mach/irqs.h> -#include <mach/gpio.h> +#include <asm/gpio.h> #define USB_CTRL IO_ADDRESS(PNX4008_PWRMAN_BASE + 0x64) diff --git a/drivers/usb/musb/davinci.c b/drivers/usb/musb/davinci.c index 8bdf25a8b023..f9a3f62a83b5 100644 --- a/drivers/usb/musb/davinci.c +++ b/drivers/usb/musb/davinci.c @@ -35,7 +35,7 @@ #include <mach/hardware.h> #include <mach/memory.h> -#include <mach/gpio.h> +#include <asm/gpio.h> #include <mach/cputype.h> #include <asm/mach-types.h> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c index 817ab60f7537..dda920623c6a 100644 --- a/drivers/video/atmel_lcdfb.c +++ b/drivers/video/atmel_lcdfb.c @@ -21,7 +21,7 @@ #include <mach/board.h> #include <mach/cpu.h> -#include <mach/gpio.h> +#include <asm/gpio.h> #include <video/atmel_lcdc.h> diff --git a/drivers/video/omap/lcd_apollon.c b/drivers/video/omap/lcd_apollon.c index 10459d8bd9a0..4b24f549f9b9 100644 --- a/drivers/video/omap/lcd_apollon.c +++ b/drivers/video/omap/lcd_apollon.c @@ -24,7 +24,7 @@ #include <linux/module.h> #include <linux/platform_device.h> -#include <mach/gpio.h> +#include <asm/gpio.h> #include "omapfb.h" diff --git a/drivers/video/omap/lcd_h3.c b/drivers/video/omap/lcd_h3.c index 8df688748b5a..622ad839fd9d 100644 --- a/drivers/video/omap/lcd_h3.c +++ b/drivers/video/omap/lcd_h3.c @@ -23,7 +23,7 @@ #include <linux/platform_device.h> #include <linux/i2c/tps65010.h> -#include <mach/gpio.h> +#include <asm/gpio.h> #include "omapfb.h" #define MODULE_NAME "omapfb-lcd_h3" diff --git a/drivers/video/omap/lcd_inn1610.c b/drivers/video/omap/lcd_inn1610.c index 9fff86f67bde..12cc52a70f96 100644 --- a/drivers/video/omap/lcd_inn1610.c +++ b/drivers/video/omap/lcd_inn1610.c @@ -22,7 +22,7 @@ #include <linux/module.h> #include <linux/platform_device.h> -#include <mach/gpio.h> +#include <asm/gpio.h> #include "omapfb.h" #define MODULE_NAME "omapfb-lcd_h3" diff --git a/drivers/video/omap/lcd_ldp.c b/drivers/video/omap/lcd_ldp.c index 0f5952cae85e..062466402c0e 100644 --- a/drivers/video/omap/lcd_ldp.c +++ b/drivers/video/omap/lcd_ldp.c @@ -26,7 +26,7 @@ #include <linux/delay.h> #include <linux/i2c/twl.h> -#include <mach/gpio.h> +#include <asm/gpio.h> #include <plat/mux.h> #include <asm/mach-types.h> diff --git a/drivers/video/omap/lcd_osk.c b/drivers/video/omap/lcd_osk.c index b87e8b83f29c..6f8d13c41202 100644 --- a/drivers/video/omap/lcd_osk.c +++ b/drivers/video/omap/lcd_osk.c @@ -23,7 +23,7 @@ #include <linux/module.h> #include <linux/platform_device.h> -#include <mach/gpio.h> +#include <asm/gpio.h> #include <plat/mux.h> #include "omapfb.h" diff --git a/drivers/video/omap/lcd_overo.c b/drivers/video/omap/lcd_overo.c index 564933ffac6e..b8fd5b2ec29c 100644 --- a/drivers/video/omap/lcd_overo.c +++ b/drivers/video/omap/lcd_overo.c @@ -23,7 +23,7 @@ #include <linux/platform_device.h> #include <linux/i2c/twl.h> -#include <mach/gpio.h> +#include <asm/gpio.h> #include <plat/mux.h> #include <asm/mach-types.h> diff --git a/drivers/video/omap/lcd_palmtt.c b/drivers/video/omap/lcd_palmtt.c index ff0e6d7ab3a2..b51b332e5a2b 100644 --- a/drivers/video/omap/lcd_palmtt.c +++ b/drivers/video/omap/lcd_palmtt.c @@ -29,7 +29,7 @@ GPIO13 - screen blanking #include <linux/module.h> #include <linux/io.h> -#include <mach/gpio.h> +#include <asm/gpio.h> #include "omapfb.h" static int palmtt_panel_init(struct lcd_panel *panel, diff --git a/drivers/video/pnx4008/sdum.c b/drivers/video/pnx4008/sdum.c index 5ec4f2d439c9..50e00395240f 100644 --- a/drivers/video/pnx4008/sdum.c +++ b/drivers/video/pnx4008/sdum.c @@ -30,7 +30,7 @@ #include <linux/clk.h> #include <linux/gfp.h> #include <asm/uaccess.h> -#include <mach/gpio.h> +#include <asm/gpio.h> #include "sdum.h" #include "fbcommon.h" |