diff options
| -rw-r--r-- | drivers/misc/ti-st/st_kim.c | 37 |
1 files changed, 36 insertions, 1 deletions
diff --git a/drivers/misc/ti-st/st_kim.c b/drivers/misc/ti-st/st_kim.c index 9ff942a346ed..83269f1d16e3 100644 --- a/drivers/misc/ti-st/st_kim.c +++ b/drivers/misc/ti-st/st_kim.c @@ -468,6 +468,11 @@ long st_kim_start(void *kim_data) if (pdata->chip_enable) pdata->chip_enable(kim_gdata); + /* Configure BT nShutdown to HIGH state */ + gpio_set_value(kim_gdata->nshutdown, GPIO_LOW); + mdelay(5); /* FIXME: a proper toggle */ + gpio_set_value(kim_gdata->nshutdown, GPIO_HIGH); + mdelay(100); /* re-initialize the completion */ INIT_COMPLETION(kim_gdata->ldisc_installed); /* send notification to UIM */ @@ -509,7 +514,8 @@ long st_kim_start(void *kim_data) * (b) upon failure to either install ldisc or download firmware. * The function is responsible to (a) notify UIM about un-installation, * (b) flush UART if the ldisc was installed. - * (c) invoke platform's chip disabling routine. + * (c) reset BT_EN - pull down nshutdown at the end. + * (d) invoke platform's chip disabling routine. */ long st_kim_stop(void *kim_data) { @@ -541,6 +547,13 @@ long st_kim_stop(void *kim_data) err = -ETIMEDOUT; } + /* By default configure BT nShutdown to LOW state */ + gpio_set_value(kim_gdata->nshutdown, GPIO_LOW); + mdelay(1); + gpio_set_value(kim_gdata->nshutdown, GPIO_HIGH); + mdelay(1); + gpio_set_value(kim_gdata->nshutdown, GPIO_LOW); + /* platform specific disable */ if (pdata->chip_disable) pdata->chip_disable(kim_gdata); @@ -733,6 +746,20 @@ static int kim_probe(struct platform_device *pdev) /* refer to itself */ kim_gdata->core_data->kim_data = kim_gdata; + /* Claim the chip enable nShutdown gpio from the system */ + kim_gdata->nshutdown = pdata->nshutdown_gpio; + err = gpio_request(kim_gdata->nshutdown, "kim"); + if (unlikely(err)) { + pr_err(" gpio %ld request failed ", kim_gdata->nshutdown); + return err; + } + + /* Configure nShutdown GPIO as output=0 */ + err = gpio_direction_output(kim_gdata->nshutdown, 0); + if (unlikely(err)) { + pr_err(" unable to configure gpio %ld", kim_gdata->nshutdown); + return err; + } /* get reference of pdev for request_firmware */ kim_gdata->kim_pdev = pdev; @@ -779,10 +806,18 @@ err_core_init: static int kim_remove(struct platform_device *pdev) { + /* free the GPIOs requested */ + struct ti_st_plat_data *pdata = pdev->dev.platform_data; struct kim_data_s *kim_gdata; kim_gdata = dev_get_drvdata(&pdev->dev); + /* Free the Bluetooth/FM/GPIO + * nShutdown gpio from the system + */ + gpio_free(pdata->nshutdown_gpio); + pr_info("nshutdown GPIO Freed"); + debugfs_remove_recursive(kim_debugfs_dir); sysfs_remove_group(&pdev->dev.kobj, &uim_attr_grp); pr_info("sysfs entries removed"); |