diff options
| -rw-r--r-- | drivers/staging/comedi/drivers/adl_pci9118.c | 109 |
1 files changed, 55 insertions, 54 deletions
diff --git a/drivers/staging/comedi/drivers/adl_pci9118.c b/drivers/staging/comedi/drivers/adl_pci9118.c index da3fecd93275..f30b84e1987b 100644 --- a/drivers/staging/comedi/drivers/adl_pci9118.c +++ b/drivers/staging/comedi/drivers/adl_pci9118.c @@ -7,61 +7,62 @@ * * Author: Michal Dobes <dobes@tesnet.cz> * -*/ + */ + /* -Driver: adl_pci9118 -Description: Adlink PCI-9118DG, PCI-9118HG, PCI-9118HR -Author: Michal Dobes <dobes@tesnet.cz> -Devices: [ADLink] PCI-9118DG (pci9118dg), PCI-9118HG (pci9118hg), - PCI-9118HR (pci9118hr) -Status: works - -This driver supports AI, AO, DI and DO subdevices. -AI subdevice supports cmd and insn interface, -other subdevices support only insn interface. -For AI: -- If cmd->scan_begin_src=TRIG_EXT then trigger input is TGIN (pin 46). -- If cmd->convert_src=TRIG_EXT then trigger input is EXTTRG (pin 44). -- If cmd->start_src/stop_src=TRIG_EXT then trigger input is TGIN (pin 46). -- It is not necessary to have cmd.scan_end_arg=cmd.chanlist_len but - cmd.scan_end_arg modulo cmd.chanlist_len must by 0. -- If return value of cmdtest is 5 then you've bad channel list - (it isn't possible mixture S.E. and DIFF inputs or bipolar and unipolar - ranges). - -There are some hardware limitations: -a) You cann't use mixture of unipolar/bipoar ranges or differencial/single - ended inputs. -b) DMA transfers must have the length aligned to two samples (32 bit), - so there is some problems if cmd->chanlist_len is odd. This driver tries - bypass this with adding one sample to the end of the every scan and discard - it on output but this cann't be used if cmd->scan_begin_src=TRIG_FOLLOW - and is used flag TRIG_WAKE_EOS, then driver switch to interrupt driven mode - with interrupt after every sample. -c) If isn't used DMA then you can use only mode where - cmd->scan_begin_src=TRIG_FOLLOW. - -Configuration options: - [0] - PCI bus of device (optional) - [1] - PCI slot of device (optional) - If bus/slot is not specified, then first available PCI - card will be used. - [2] - 0= standard 8 DIFF/16 SE channels configuration - n = external multiplexer connected, 1 <= n <= 256 - [3] - 0=autoselect DMA or EOC interrupts operation - 1 = disable DMA mode - 3 = disable DMA and INT, only insn interface will work - [4] - sample&hold signal - card can generate signal for external S&H board - 0 = use SSHO(pin 45) signal is generated in onboard hardware S&H logic - 0 != use ADCHN7(pin 23) signal is generated from driver, number say how - long delay is requested in ns and sign polarity of the hold - (in this case external multiplexor can serve only 128 channels) - [5] - 0=stop measure on all hardware errors - 2 | = ignore ADOR - A/D Overrun status - 8|=ignore Bover - A/D Burst Mode Overrun status - 256|=ignore nFull - A/D FIFO Full status - -*/ + * Driver: adl_pci9118 + * Description: Adlink PCI-9118DG, PCI-9118HG, PCI-9118HR + * Author: Michal Dobes <dobes@tesnet.cz> + * Devices: [ADLink] PCI-9118DG (pci9118dg), PCI-9118HG (pci9118hg), + * PCI-9118HR (pci9118hr) + * Status: works + * + * This driver supports AI, AO, DI and DO subdevices. + * AI subdevice supports cmd and insn interface, + * other subdevices support only insn interface. + * For AI: + * - If cmd->scan_begin_src=TRIG_EXT then trigger input is TGIN (pin 46). + * - If cmd->convert_src=TRIG_EXT then trigger input is EXTTRG (pin 44). + * - If cmd->start_src/stop_src=TRIG_EXT then trigger input is TGIN (pin 46). + * - It is not necessary to have cmd.scan_end_arg=cmd.chanlist_len but + * cmd.scan_end_arg modulo cmd.chanlist_len must by 0. + * - If return value of cmdtest is 5 then you've bad channel list + * (it isn't possible mixture S.E. and DIFF inputs or bipolar and unipolar + * ranges). + * + * There are some hardware limitations: + * a) You cann't use mixture of unipolar/bipoar ranges or differencial/single + * ended inputs. + * b) DMA transfers must have the length aligned to two samples (32 bit), + * so there is some problems if cmd->chanlist_len is odd. This driver tries + * bypass this with adding one sample to the end of the every scan and discard + * it on output but this cann't be used if cmd->scan_begin_src=TRIG_FOLLOW + * and is used flag TRIG_WAKE_EOS, then driver switch to interrupt driven mode + * with interrupt after every sample. + * c) If isn't used DMA then you can use only mode where + * cmd->scan_begin_src=TRIG_FOLLOW. + * + * Configuration options: + * [0] - PCI bus of device (optional) + * [1] - PCI slot of device (optional) + * If bus/slot is not specified, then first available PCI + * card will be used. + * [2] - 0= standard 8 DIFF/16 SE channels configuration + * n = external multiplexer connected, 1 <= n <= 256 + * [3] - 0=autoselect DMA or EOC interrupts operation + * 1 = disable DMA mode + * 3 = disable DMA and INT, only insn interface will work + * [4] - sample&hold signal - card can generate signal for external S&H board + * 0 = use SSHO(pin 45) signal is generated in onboard hardware S&H logic + * 0 != use ADCHN7(pin 23) signal is generated from driver, number say how + * long delay is requested in ns and sign polarity of the hold + * (in this case external multiplexor can serve only 128 channels) + * [5] - 0=stop measure on all hardware errors + * 2 | = ignore ADOR - A/D Overrun status + * 8|=ignore Bover - A/D Burst Mode Overrun status + * 256|=ignore nFull - A/D FIFO Full status + * + */ /* * FIXME |