diff options
35 files changed, 1141 insertions, 210 deletions
diff --git a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt new file mode 100644 index 000000000000..12b18f82d441 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt @@ -0,0 +1,70 @@ +Amlogic Meson AXG DWC PCIE SoC controller + +Amlogic Meson PCIe host controller is based on the Synopsys DesignWare PCI core. +It shares common functions with the PCIe DesignWare core driver and +inherits common properties defined in +Documentation/devicetree/bindings/pci/designware-pci.txt. + +Additional properties are described here: + +Required properties: +- compatible: + should contain "amlogic,axg-pcie" to identify the core. +- reg: + should contain the configuration address space. +- reg-names: Must be + - "elbi" External local bus interface registers + - "cfg" Meson specific registers + - "phy" Meson PCIE PHY registers + - "config" PCIe configuration space +- reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal. +- clocks: Must contain an entry for each entry in clock-names. +- clock-names: Must include the following entries: + - "pclk" PCIe GEN 100M PLL clock + - "port" PCIe_x(A or B) RC clock gate + - "general" PCIe Phy clock + - "mipi" PCIe_x(A or B) 100M ref clock gate +- resets: phandle to the reset lines. +- reset-names: must contain "phy" "port" and "apb" + - "phy" Share PHY reset + - "port" Port A or B reset + - "apb" Share APB reset +- device_type: + should be "pci". As specified in designware-pcie.txt + + +Example configuration: + + pcie: pcie@f9800000 { + compatible = "amlogic,axg-pcie", "snps,dw-pcie"; + reg = <0x0 0xf9800000 0x0 0x400000 + 0x0 0xff646000 0x0 0x2000 + 0x0 0xff644000 0x0 0x2000 + 0x0 0xf9f00000 0x0 0x100000>; + reg-names = "elbi", "cfg", "phy", "config"; + reset-gpios = <&gpio GPIOX_19 GPIO_ACTIVE_HIGH>; + interrupts = <GIC_SPI 177 IRQ_TYPE_EDGE_RISING>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 179 IRQ_TYPE_EDGE_RISING>; + bus-range = <0x0 0xff>; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x82000000 0 0 0x0 0xf9c00000 0 0x00300000>; + + clocks = <&clkc CLKID_USB + &clkc CLKID_MIPI_ENABLE + &clkc CLKID_PCIE_A + &clkc CLKID_PCIE_CML_EN0>; + clock-names = "general", + "mipi", + "pclk", + "port"; + resets = <&reset RESET_PCIE_PHY>, + <&reset RESET_PCIE_A>, + <&reset RESET_PCIE_APB>; + reset-names = "phy", + "port", + "apb"; + }; diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt index f37494d5a7be..d514c1f2365f 100644 --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt @@ -41,7 +41,9 @@ Optional properties: Additional required properties for imx6sx-pcie: - clock names: Must include the following additional entries: - "pcie_inbound_axi" -- power-domains: Must be set to a phandle pointing to the PCIE_PHY power domain +- power-domains: Must be set to phandles pointing to the DISPLAY and + PCIE_PHY power domains +- power-domain-names: Must be "pcie", "pcie_phy" Additional required properties for imx7d-pcie: - power-domains: Must be set to a phandle pointing to PCIE_PHY power domain diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt index 20227a875ac8..92437a366e5f 100644 --- a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt +++ b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt @@ -65,7 +65,6 @@ Required properties: explanation. - ranges: Sub-ranges distributed from the PCIe controller node. An empty property is sufficient. -- num-lanes: Number of lanes to use for this port. Examples for MT7623: @@ -118,7 +117,6 @@ Examples for MT7623: interrupt-map-mask = <0 0 0 0>; interrupt-map = <0 0 0 0 &sysirq GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>; ranges; - num-lanes = <1>; }; pcie@1,0 { @@ -129,7 +127,6 @@ Examples for MT7623: interrupt-map-mask = <0 0 0 0>; interrupt-map = <0 0 0 0 &sysirq GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>; ranges; - num-lanes = <1>; }; pcie@2,0 { @@ -140,7 +137,6 @@ Examples for MT7623: interrupt-map-mask = <0 0 0 0>; interrupt-map = <0 0 0 0 &sysirq GIC_SPI 195 IRQ_TYPE_LEVEL_LOW>; ranges; - num-lanes = <1>; }; }; @@ -172,7 +168,6 @@ Examples for MT2712: #size-cells = <2>; #interrupt-cells = <1>; ranges; - num-lanes = <1>; interrupt-map-mask = <0 0 0 7>; interrupt-map = <0 0 0 1 &pcie_intc0 0>, <0 0 0 2 &pcie_intc0 1>, @@ -191,7 +186,6 @@ Examples for MT2712: #size-cells = <2>; #interrupt-cells = <1>; ranges; - num-lanes = <1>; interrupt-map-mask = <0 0 0 7>; interrupt-map = <0 0 0 1 &pcie_intc1 0>, <0 0 0 2 &pcie_intc1 1>, @@ -245,7 +239,6 @@ Examples for MT7622: #size-cells = <2>; #interrupt-cells = <1>; ranges; - num-lanes = <1>; interrupt-map-mask = <0 0 0 7>; interrupt-map = <0 0 0 1 &pcie_intc0 0>, <0 0 0 2 &pcie_intc0 1>, @@ -264,7 +257,6 @@ Examples for MT7622: #size-cells = <2>; #interrupt-cells = <1>; ranges; - num-lanes = <1>; interrupt-map-mask = <0 0 0 7>; interrupt-map = <0 0 0 1 &pcie_intc1 0>, <0 0 0 2 &pcie_intc1 1>, diff --git a/Documentation/driver-api/pci/p2pdma.rst b/Documentation/driver-api/pci/p2pdma.rst index 4c577fa7bef9..6d85b5a2598d 100644 --- a/Documentation/driver-api/pci/p2pdma.rst +++ b/Documentation/driver-api/pci/p2pdma.rst @@ -49,7 +49,7 @@ For example, in the NVMe Target Copy Offload implementation: in that it exposes any CMB (Controller Memory Buffer) as a P2P memory resource (provider), it accepts P2P memory pages as buffers in requests to be used directly (client) and it can also make use of the CMB as - submission queue entries (orchastrator). + submission queue entries (orchestrator). * The RDMA driver is a client in this arrangement so that an RNIC can DMA directly to the memory exposed by the NVMe device. * The NVMe Target driver (nvmet) can orchestrate the data from the RNIC @@ -111,7 +111,7 @@ that's compatible with all clients using :c:func:`pci_p2pmem_find()`. If more than one provider is supported, the one nearest to all the clients will be chosen first. If more than one provider is an equal distance away, the one returned will be chosen at random (it is not an arbitrary but -truely random). This function returns the PCI device to use for the provider +truly random). This function returns the PCI device to use for the provider with a reference taken and therefore when it's no longer needed it should be returned with pci_dev_put(). diff --git a/MAINTAINERS b/MAINTAINERS index f47a64769add..68c5be2633b2 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -11500,6 +11500,7 @@ F: include/uapi/linux/pci* F: lib/pci* F: arch/x86/pci/ F: arch/x86/kernel/quirks.c +F: arch/x86/kernel/early-quirks.c PCI NATIVE HOST BRIDGE AND ENDPOINT DRIVERS M: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> @@ -11509,6 +11510,13 @@ T: git git://git.kernel.org/pub/scm/linux/kernel/git/lpieralisi/pci.git/ S: Supported F: drivers/pci/controller/ +PCIE DRIVER FOR AMLOGIC MESON +M: Yue Wang <yue.wang@Amlogic.com> +L: linux-pci@vger.kernel.org +L: linux-amlogic@lists.infradead.org +S: Maintained +F: drivers/pci/controller/dwc/pci-meson.c + PCIE DRIVER FOR AXIS ARTPEC M: Jesper Nilsson <jesper.nilsson@axis.com> L: linux-arm-kernel@axis.com @@ -11541,7 +11549,6 @@ F: Documentation/devicetree/bindings/pci/kirin-pcie.txt F: drivers/pci/controller/dwc/pcie-kirin.c PCIE DRIVER FOR HISILICON STB -M: Jianguo Sun <sunjianguo1@huawei.com> M: Shawn Guo <shawn.guo@linaro.org> L: linux-pci@vger.kernel.org S: Maintained diff --git a/arch/arm/boot/dts/mt7623.dtsi b/arch/arm/boot/dts/mt7623.dtsi index d01bdee6f2f3..98f115966391 100644 --- a/arch/arm/boot/dts/mt7623.dtsi +++ b/arch/arm/boot/dts/mt7623.dtsi @@ -850,7 +850,6 @@ interrupt-map-mask = <0 0 0 0>; interrupt-map = <0 0 0 0 &sysirq GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>; ranges; - num-lanes = <1>; status = "disabled"; }; @@ -862,7 +861,6 @@ interrupt-map-mask = <0 0 0 0>; interrupt-map = <0 0 0 0 &sysirq GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>; ranges; - num-lanes = <1>; status = "disabled"; }; @@ -874,7 +872,6 @@ interrupt-map-mask = <0 0 0 0>; interrupt-map = <0 0 0 0 &sysirq GIC_SPI 195 IRQ_TYPE_LEVEL_LOW>; ranges; - num-lanes = <1>; status = "disabled"; }; }; diff --git a/arch/arm64/boot/dts/mediatek/mt7622.dtsi b/arch/arm64/boot/dts/mediatek/mt7622.dtsi index fe0c875f1d95..f3cba1f52fde 100644 --- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi @@ -812,7 +812,6 @@ ranges; status = "disabled"; - num-lanes = <1>; interrupt-map-mask = <0 0 0 7>; interrupt-map = <0 0 0 1 &pcie_intc0 0>, <0 0 0 2 &pcie_intc0 1>, @@ -833,7 +832,6 @@ ranges; status = "disabled"; - num-lanes = <1>; interrupt-map-mask = <0 0 0 7>; interrupt-map = <0 0 0 1 &pcie_intc1 0>, <0 0 0 2 &pcie_intc1 1>, diff --git a/arch/s390/pci/pci.c b/arch/s390/pci/pci.c index 9f6f392a4461..4266a4de3160 100644 --- a/arch/s390/pci/pci.c +++ b/arch/s390/pci/pci.c @@ -651,6 +651,9 @@ int pcibios_add_device(struct pci_dev *pdev) struct resource *res; int i; + if (pdev->is_physfn) + pdev->no_vf_scan = 1; + pdev->dev.groups = zpci_attr_groups; pdev->dev.dma_ops = &s390_pci_dma_ops; zpci_map_resources(pdev); diff --git a/arch/x86/pci/broadcom_bus.c b/arch/x86/pci/broadcom_bus.c index 526536c81ddc..ca1e8e6dccc8 100644 --- a/arch/x86/pci/broadcom_bus.c +++ b/arch/x86/pci/broadcom_bus.c @@ -50,8 +50,8 @@ static void __init cnb20le_res(u8 bus, u8 slot, u8 func) word1 = read_pci_config_16(bus, slot, func, 0xc0); word2 = read_pci_config_16(bus, slot, func, 0xc2); if (word1 != word2) { - res.start = (word1 << 16) | 0x0000; - res.end = (word2 << 16) | 0xffff; + res.start = ((resource_size_t) word1 << 16) | 0x0000; + res.end = ((resource_size_t) word2 << 16) | 0xffff; res.flags = IORESOURCE_MEM; update_res(info, res.start, res.end, res.flags, 0); } diff --git a/drivers/pci/Kconfig b/drivers/pci/Kconfig index 2dcc30429e8b..ffe7895aa880 100644 --- a/drivers/pci/Kconfig +++ b/drivers/pci/Kconfig @@ -73,9 +73,9 @@ config PCI_PF_STUB depends on PCI_IOV help Say Y or M here if you want to enable support for devices that - require SR-IOV support, while at the same time the PF itself is - not providing any actual services on the host itself such as - storage or networking. + require SR-IOV support, while at the same time the PF (Physical + Function) itself is not providing any actual services on the + host itself such as storage or networking. When in doubt, say N. diff --git a/drivers/pci/controller/dwc/Kconfig b/drivers/pci/controller/dwc/Kconfig index 955068867c35..548c58223868 100644 --- a/drivers/pci/controller/dwc/Kconfig +++ b/drivers/pci/controller/dwc/Kconfig @@ -89,8 +89,8 @@ config PCI_EXYNOS select PCIE_DW_HOST config PCI_IMX6 - bool "Freescale i.MX6 PCIe controller" - depends on SOC_IMX6Q || (ARM && COMPILE_TEST) + bool "Freescale i.MX6/7 PCIe controller" + depends on SOC_IMX6Q || SOC_IMX7D || (ARM && COMPILE_TEST) depends on PCI_MSI_IRQ_DOMAIN select PCIE_DW_HOST @@ -193,6 +193,16 @@ config PCIE_HISI_STB help Say Y here if you want PCIe controller support on HiSilicon STB SoCs +config PCI_MESON + bool "MESON PCIe controller" + depends on PCI_MSI_IRQ_DOMAIN + select PCIE_DW_HOST + help + Say Y here if you want to enable PCI controller support on Amlogic + SoCs. The PCI controller on Amlogic is based on DesignWare hardware + and therefore the driver re-uses the DesignWare core functions to + implement the driver. + config PCIE_UNIPHIER bool "Socionext UniPhier PCIe controllers" depends on ARCH_UNIPHIER || COMPILE_TEST diff --git a/drivers/pci/controller/dwc/Makefile b/drivers/pci/controller/dwc/Makefile index 688a0ec13121..7bcdcdf5024e 100644 --- a/drivers/pci/controller/dwc/Makefile +++ b/drivers/pci/controller/dwc/Makefile @@ -14,6 +14,7 @@ obj-$(CONFIG_PCIE_ARMADA_8K) += pcie-armada8k.o obj-$(CONFIG_PCIE_ARTPEC6) += pcie-artpec6.o obj-$(CONFIG_PCIE_KIRIN) += pcie-kirin.o obj-$(CONFIG_PCIE_HISI_STB) += pcie-histb.o +obj-$(CONFIG_PCI_MESON) += pci-meson.o obj-$(CONFIG_PCIE_UNIPHIER) += pcie-uniphier.o # The following drivers are for devices that use the generic ACPI diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c index 2cbef2d7c207..25a2b7683e55 100644 --- a/drivers/pci/controller/dwc/pci-imx6.c +++ b/drivers/pci/controller/dwc/pci-imx6.c @@ -27,6 +27,8 @@ #include <linux/types.h> #include <linux/interrupt.h> #include <linux/reset.h> +#include <linux/pm_domain.h> +#include <linux/pm_runtime.h> #include "pcie-designware.h" @@ -59,6 +61,11 @@ struct imx6_pcie { u32 tx_swing_low; int link_gen; struct regulator *vpcie; + + /* power domain for pcie */ + struct device *pd_pcie; + /* power domain for pcie phy */ + struct device *pd_pcie_phy; }; /* Parameters for the waiting for PCIe PHY PLL to lock on i.MX7 */ @@ -292,6 +299,43 @@ static int imx6q_pcie_abort_handler(unsigned long addr, return 1; } +static int imx6_pcie_attach_pd(struct device *dev) +{ + struct imx6_pcie *imx6_pcie = dev_get_drvdata(dev); + struct device_link *link; + + /* Do nothing when in a single power domain */ + if (dev->pm_domain) + return 0; + + imx6_pcie->pd_pcie = dev_pm_domain_attach_by_name(dev, "pcie"); + if (IS_ERR(imx6_pcie->pd_pcie)) + return PTR_ERR(imx6_pcie->pd_pcie); + link = device_link_add(dev, imx6_pcie->pd_pcie, + DL_FLAG_STATELESS | + DL_FLAG_PM_RUNTIME | + DL_FLAG_RPM_ACTIVE); + if (!link) { + dev_err(dev, "Failed to add device_link to pcie pd.\n"); + return -EINVAL; + } + + imx6_pcie->pd_pcie_phy = dev_pm_domain_attach_by_name(dev, "pcie_phy"); + if (IS_ERR(imx6_pcie->pd_pcie_phy)) + return PTR_ERR(imx6_pcie->pd_pcie_phy); + + device_link_add(dev, imx6_pcie->pd_pcie_phy, + DL_FLAG_STATELESS | + DL_FLAG_PM_RUNTIME | + DL_FLAG_RPM_ACTIVE); + if (IS_ERR(link)) { + dev_err(dev, "Failed to add device_link to pcie_phy pd: %ld\n", PTR_ERR(link)); + return PTR_ERR(link); + } + + return 0; +} + static void imx6_pcie_assert_core_reset(struct imx6_pcie *imx6_pcie) { struct device *dev = imx6_pcie->pci->dev; @@ -773,8 +817,28 @@ static void imx6_pcie_ltssm_disable(struct device *dev) static void imx6_pcie_pm_turnoff(struct imx6_pcie *imx6_pcie) { - reset_control_assert(imx6_pcie->turnoff_reset); - reset_control_deassert(imx6_pcie->turnoff_reset); + struct device *dev = imx6_pcie->pci->dev; + + /* Some variants have a turnoff reset in DT */ + if (imx6_pcie->turnoff_reset) { + reset_control_assert(imx6_pcie->turnoff_reset); + reset_control_deassert(imx6_pcie->turnoff_reset); + goto pm_turnoff_sleep; + } + + /* Others poke directly at IOMUXC registers */ + switch (imx6_pcie->variant) { + case IMX6SX: + regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12, + IMX6SX_GPR12_PCIE_PM_TURN_OFF, + IMX6SX_GPR12_PCIE_PM_TURN_OFF); + regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12, + IMX6SX_GPR12_PCIE_PM_TURN_OFF, 0); + break; + default: + dev_err(dev, "PME_Turn_Off not implemented\n"); + return; + } /* * Components with an upstream port must respond to @@ -783,6 +847,7 @@ static void imx6_pcie_pm_turnoff(struct imx6_pcie *imx6_pcie) * The standard recommends a 1-10ms timeout after which to * proceed anyway as if acks were received. */ +pm_turnoff_sleep: usleep_range(1000, 10000); } @@ -792,18 +857,31 @@ static void imx6_pcie_clk_disable(struct imx6_pcie *imx6_pcie) clk_disable_unprepare(imx6_pcie->pcie_phy); clk_disable_unprepare(imx6_pcie->pcie_bus); - if (imx6_pcie->variant == IMX7D) { + switch (imx6_pcie->variant) { + case IMX6SX: + clk_disable_unprepare(imx6_pcie->pcie_inbound_axi); + break; + case IMX7D: regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12, IMX7D_GPR12_PCIE_PHY_REFCLK_SEL, IMX7D_GPR12_PCIE_PHY_REFCLK_SEL); + break; + default: + break; } } +static inline bool imx6_pcie_supports_suspend(struct imx6_pcie *imx6_pcie) +{ + return (imx6_pcie->variant == IMX7D || + imx6_pcie->variant == IMX6SX); +} + static int imx6_pcie_suspend_noirq(struct device *dev) { struct imx6_pcie *imx6_pcie = dev_get_drvdata(dev); - if (imx6_pcie->variant != IMX7D) + if (!imx6_pcie_supports_suspend(imx6_pcie)) return 0; imx6_pcie_pm_turnoff(imx6_pcie); @@ -819,7 +897,7 @@ static int imx6_pcie_resume_noirq(struct device *dev) struct imx6_pcie *imx6_pcie = dev_get_drvdata(dev); struct pcie_port *pp = &imx6_pcie->pci->pp; - if (imx6_pcie->variant != IMX7D) + if (!imx6_pcie_supports_suspend(imx6_pcie)) return 0; imx6_pcie_assert_core_reset(imx6_pcie); @@ -985,6 +1063,10 @@ static int imx6_pcie_probe(struct platform_device *pdev) platform_set_drvdata(pdev, imx6_pcie); + ret = imx6_pcie_attach_pd(dev); + if (ret) + return ret; + ret = imx6_add_pcie_port(imx6_pcie, pdev); if (ret < 0) return ret; diff --git a/drivers/pci/controller/dwc/pci-layerscape.c b/drivers/pci/controller/dwc/pci-layerscape.c index 3724d3ef7008..905a0ab0e6fa 100644 --- a/drivers/pci/controller/dwc/pci-layerscape.c +++ b/drivers/pci/controller/dwc/pci-layerscape.c @@ -222,12 +222,12 @@ static const struct dw_pcie_ops dw_ls_pcie_ops = { .link_up = ls_pcie_link_up, }; -static struct ls_pcie_drvdata ls1021_drvdata = { +static const struct ls_pcie_drvdata ls1021_drvdata = { .ops = &ls1021_pcie_host_ops, .dw_pcie_ops = &dw_ls1021_pcie_ops, }; -static struct ls_pcie_drvdata ls1043_drvdata = { +static const struct ls_pcie_drvdata ls1043_drvdata = { .lut_offset = 0x10000, .ltssm_shift = 24, .lut_dbg = 0x7fc, @@ -235,7 +235,7 @@ static struct ls_pcie_drvdata ls1043_drvdata = { .dw_pcie_ops = &dw_ls_pcie_ops, }; -static struct ls_pcie_drvdata ls1046_drvdata = { +static const struct ls_pcie_drvdata ls1046_drvdata = { .lut_offset = 0x80000, .ltssm_shift = 24, .lut_dbg = 0x407fc, @@ -243,7 +243,7 @@ static struct ls_pcie_drvdata ls1046_drvdata = { .dw_pcie_ops = &dw_ls_pcie_ops, }; -static struct ls_pcie_drvdata ls2080_drvdata = { +static const struct ls_pcie_drvdata ls2080_drvdata = { .lut_offset = 0x80000, .ltssm_shift = 0, .lut_dbg = 0x7fc, @@ -251,7 +251,7 @@ static struct ls_pcie_drvdata ls2080_drvdata = { .dw_pcie_ops = &dw_ls_pcie_ops, }; -static struct ls_pcie_drvdata ls2088_drvdata = { +static const struct ls_pcie_drvdata ls2088_drvdata = { .lut_offset = 0x80000, .ltssm_shift = 0, .lut_dbg = 0x407fc, diff --git a/drivers/pci/controller/dwc/pci-meson.c b/drivers/pci/controller/dwc/pci-meson.c new file mode 100644 index 000000000000..241ebe0c4505 --- /dev/null +++ b/drivers/pci/controller/dwc/pci-meson.c @@ -0,0 +1,592 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * PCIe host controller driver for Amlogic MESON SoCs + * + * Copyright (c) 2018 Amlogic, inc. + * Author: Yue Wang <yue.wang@amlogic.com> + */ + +#include <linux/clk.h> +#include <linux/delay.h> +#include <linux/of_device.h> +#include <linux/of_gpio.h> +#include <linux/pci.h> +#include <linux/platform_device.h> +#include <linux/reset.h> +#include <linux/resource.h> +#include <linux/types.h> + +#include "pcie-designware.h" + +#define to_meson_pcie(x) dev_get_drvdata((x)->dev) + +/* External local bus interface registers */ +#define PLR_OFFSET 0x700 +#define PCIE_PORT_LINK_CTRL_OFF (PLR_OFFSET + 0x10) +#define FAST_LINK_MODE BIT(7) +#define LINK_CAPABLE_MASK GENMASK(21, 16) +#define LINK_CAPABLE_X1 BIT(16) + +#define PCIE_GEN2_CTRL_OFF (PLR_OFFSET + 0x10c) +#define NUM_OF_LANES_MASK GENMASK(12, 8) +#define NUM_OF_LANES_X1 BIT(8) +#define DIRECT_SPEED_CHANGE BIT(17) + +#define TYPE1_HDR_OFFSET 0x0 +#define PCIE_STATUS_COMMAND (TYPE1_HDR_OFFSET + 0x04) +#define PCI_IO_EN BIT(0) +#define PCI_MEM_SPACE_EN BIT(1) +#define PCI_BUS_MASTER_EN BIT(2) + +#define PCIE_BASE_ADDR0 (TYPE1_HDR_OFFSET + 0x10) +#define PCIE_BASE_ADDR1 (TYPE1_HDR_OFFSET + 0x14) + +#define PCIE_CAP_OFFSET 0x70 +#define PCIE_DEV_CTRL_DEV_STUS (PCIE_CAP_OFFSET + 0x08) +#define PCIE_CAP_MAX_PAYLOAD_MASK GENMASK(7, 5) +#define PCIE_CAP_MAX_PAYLOAD_SIZE(x) ((x) << 5) +#define PCIE_CAP_MAX_READ_REQ_MASK GENMASK(14, 12) +#define PCIE_CAP_MAX_READ_REQ_SIZE(x) ((x) << 12) + +/* PCIe specific config registers */ +#define PCIE_CFG0 0x0 +#define APP_LTSSM_ENABLE BIT(7) + +#define PCIE_CFG_STATUS12 0x30 +#define IS_SMLH_LINK_UP(x) ((x) & (1 << 6)) +#define IS_RDLH_LINK_UP(x) ((x) & (1 << 16)) +#define IS_LTSSM_UP(x) ((((x) >> 10) & 0x1f) == 0x11) + +#define PCIE_CFG_STATUS17 0x44 +#define PM_CURRENT_STATE(x) (((x) >> 7) & 0x1) + +#define WAIT_LINKUP_TIMEOUT 4000 +#define PORT_CLK_RATE 100000000UL +#define MAX_PAYLOAD_SIZE 256 +#define MAX_READ_REQ_SIZE 256 +#define MESON_PCIE_PHY_POWERUP 0x1c +#define PCIE_RESET_DELAY 500 +#define PCIE_SHARED_RESET 1 +#define PCIE_NORMAL_RESET 0 + +enum pcie_data_rate { + PCIE_GEN1, + PCIE_GEN2, + PCIE_GEN3, + PCIE_GEN4 +}; + +struct meson_pcie_mem_res { + void __iomem *elbi_base; + void __iomem *cfg_base; + void __iomem *phy_base; +}; + +struct meson_pcie_clk_res { + struct clk *clk; + struct clk *mipi_gate; + struct clk *port_clk; + struct clk *general_clk; +}; + +struct meson_pcie_rc_reset { + struct reset_control *phy; + struct reset_control *port; + struct reset_control *apb; +}; + +struct meson_pcie { + struct dw_pcie pci; + struct meson_pcie_mem_res mem_res; + struct meson_pcie_clk_res clk_res; + struct meson_pcie_rc_reset mrst; + struct gpio_desc *reset_gpio; +}; + +static struct reset_control *meson_pcie_get_reset(struct meson_pcie *mp, + const char *id, + u32 reset_type) +{ + struct device *dev = mp->pci.dev; + struct reset_control *reset; + + if (reset_type == PCIE_SHARED_RESET) + reset = devm_reset_control_get_shared(dev, id); + else + reset = devm_reset_control_get(dev, id); + + return reset; +} + +static int meson_pcie_get_resets(struct meson_pcie *mp) +{ + struct meson_pcie_rc_reset *mrst = &mp->mrst; + + mrst->phy = meson_pcie_get_reset(mp, "phy", PCIE_SHARED_RESET); + if (IS_ERR(mrst->phy)) + return PTR_ERR(mrst->phy); + reset_control_deassert(mrst->phy); + + mrst->port = meson_pcie_get_reset(mp, "port", PCIE_NORMAL_RESET); + if (IS_ERR(mrst->port)) + return PTR_ERR(mrst->port); + reset_control_deassert(mrst->port); + + mrst->apb = meson_pcie_get_reset(mp, "apb", PCIE_SHARED_RESET); + if (IS_ERR(mrst->apb)) + return PTR_ERR(mrst->apb); + reset_control_deassert(mrst->apb); + + return 0; +} + +static void __iomem *meson_pcie_get_mem(struct platform_device *pdev, + struct meson_pcie *mp, + const char *id) +{ + struct device *dev = mp->pci.dev; + struct resource *res; + + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, id); + + return devm_ioremap_resource(dev, res); +} + +static void __iomem *meson_pcie_get_mem_shared(struct platform_device *pdev, + struct meson_pcie *mp, + const char *id) +{ + struct device *dev = mp->pci.dev; + struct resource *res; + + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, id); + if (!res) { + dev_err(dev, "No REG resource %s\n", id); + return ERR_PTR(-ENXIO); + } + + return devm_ioremap(dev, res->start, resource_size(res)); +} + +static int meson_pcie_get_mems(struct platform_device *pdev, + struct meson_pcie *mp) +{ + mp->mem_res.elbi_base = meson_pcie_get_mem(pdev, mp, "elbi"); + if (IS_ERR(mp->mem_res.elbi_base)) + return PTR_ERR(mp->mem_res.elbi_base); + + mp->mem_res.cfg_base = meson_pcie_get_mem(pdev, mp, "cfg"); + if (IS_ERR(mp->mem_res.cfg_base)) + return PTR_ERR(mp->mem_res.cfg_base); + + /* Meson SoC has two PCI controllers use same phy register*/ + mp->mem_res.phy_base = meson_pcie_get_mem_shared(pdev, mp, "phy"); + if (IS_ERR(mp->mem_res.phy_base)) + return PTR_ERR(mp->mem_res.phy_base); + + return 0; +} + +static void meson_pcie_power_on(struct meson_pcie *mp) +{ + writel(MESON_PCIE_PHY_POWERUP, mp->mem_res.phy_base); +} + +static void meson_pcie_reset(struct meson_pcie *mp) +{ + struct meson_pcie_rc_reset *mrst = &mp->mrst; + + reset_control_assert(mrst->phy); + udelay(PCIE_RESET_DELAY); + reset_control_deassert(mrst->phy); + udelay(PCIE_RESET_DELAY); + + reset_control_assert(mrst->port); + reset_control_assert(mrst->apb); + udelay(PCIE_RESET_DELAY); + reset_control_deassert(mrst->port); + reset_control_deassert(mrst->apb); + udelay(PCIE_RESET_DELAY); +} + +static inline struct clk *meson_pcie_probe_clock(struct device *dev, + const char *id, u64 rate) +{ + struct clk *clk; + int ret; + + clk = devm_clk_get(dev, id); + if (IS_ERR(clk)) + return clk; + + if (rate) { + ret = clk_set_rate(clk, rate); + if (ret) { + dev_err(dev, "set clk rate failed, ret = %d\n", ret); + return ERR_PTR(ret); + } + } + + ret = clk_prepare_enable(clk); + if (ret) { + dev_err(dev, "couldn't enable clk\n"); + return ERR_PTR(ret); + } + + devm_add_action_or_reset(dev, + (void (*) (void *))clk_disable_unprepare, + clk); + + return clk; +} + +static int meson_pcie_probe_clocks(struct meson_pcie *mp) +{ + struct device *dev = mp->pci.dev; + struct meson_pcie_clk_res *res = &mp->clk_res; + + res->port_clk = meson_pcie_probe_clock(dev, "port", PORT_CLK_RATE); + if (IS_ERR(res->port_clk)) + return PTR_ERR(res->port_clk); + + res->mipi_gate = meson_pcie_probe_clock(dev, "pcie_mipi_en", 0); + if (IS_ERR(res->mipi_gate)) + return PTR_ERR(res->mipi_gate); + + res->general_clk = meson_pcie_probe_clock(dev, "pcie_general", 0); + if (IS_ERR(res->general_clk)) + return PTR_ERR(res->general_clk); + + res->clk = meson_pcie_probe_clock(dev, "pcie", 0); + if (IS_ERR(res->clk)) + return PTR_ERR(res->clk); + + return 0; +} + +static inline void meson_elb_writel(struct meson_pcie *mp, u32 val, u32 reg) +{ + writel(val, mp->mem_res.elbi_base + reg); +} + +static inline u32 meson_elb_readl(struct meson_pcie *mp, u32 reg) +{ + return readl(mp->mem_res.elbi_base + reg); +} + +static inline u32 meson_cfg_readl(struct meson_pcie *mp, u32 reg) +{ + return readl(mp->mem_res.cfg_base + reg); +} + +static inline void meson_cfg_writel(struct meson_pcie *mp, u32 val, u32 reg) +{ + writel(val, mp->mem_res.cfg_base + reg); +} + +static void meson_pcie_assert_reset(struct meson_pcie *mp) +{ + gpiod_set_value_cansleep(mp->reset_gpio, 0); + udelay(500); + gpiod_set_value_cansleep(mp->reset_gpio, 1); +} + +static void meson_pcie_init_dw(struct meson_pcie *mp) +{ + u32 val; + + val = meson_cfg_readl(mp, PCIE_CFG0); + val |= APP_LTSSM_ENABLE; + meson_cfg_writel(mp, val, PCIE_CFG0); + + val = meson_elb_readl(mp, PCIE_PORT_LINK_CTRL_OFF); + val &= ~LINK_CAPABLE_MASK; + meson_elb_writel(mp, val, PCIE_PORT_LINK_CTRL_OFF); + + val = meson_elb_readl(mp, PCIE_PORT_LINK_CTRL_OFF); + val |= LINK_CAPABLE_X1 | FAST_LINK_MODE; + meson_elb_writel(mp, val, PCIE_PORT_LINK_CTRL_OFF); + + val = meson_elb_readl(mp, PCIE_GEN2_CTRL_OFF); + val &= ~NUM_OF_LANES_MASK; + meson_elb_writel(mp, val, PCIE_GEN2_CTRL_OFF); + + val = meson_elb_readl(mp, PCIE_GEN2_CTRL_OFF); + val |= NUM_OF_LANES_X1 | DIRECT_SPEED_CHANGE; + meson_elb_writel(mp, val, PCIE_GEN2_CTRL_OFF); + + meson_elb_writel(mp, 0x0, PCIE_BASE_ADDR0); + meson_elb_writel(mp, 0x0, PCIE_BASE_ADDR1); +} + +static int meson_size_to_payload(struct meson_pcie *mp, int size) +{ + struct device *dev = mp->pci.dev; + + /* + * dwc supports 2^(val+7) payload size, which val is 0~5 default to 1. + * So if input size is not 2^order alignment or less than 2^7 or bigger + * than 2^12, just set to default size 2^(1+7). + */ + if (!is_power_of_2(size) || size < 128 || size > 4096) { + dev_warn(dev, "payload size %d, set to default 256\n", size); + return 1; + } + + return fls(size) - 8; +} + +static void meson_set_max_payload(struct meson_pcie *mp, int size) +{ + u32 val; + int max_payload_size = meson_size_to_payload(mp, size); + + val = meson_elb_readl(mp, PCIE_DEV_CTRL_DEV_STUS); + val &= ~PCIE_CAP_MAX_PAYLOAD_MASK; + meson_elb_writel(mp, val, PCIE_DEV_CTRL_DEV_STUS); + + val = meson_elb_readl(mp, PCIE_DEV_CTRL_DEV_STUS); + val |= PCIE_CAP_MAX_PAYLOAD_SIZE(max_payload_size); + meson_elb_writel(mp, val, PCIE_DEV_CTRL_DEV_STUS); +} + +static void meson_set_max_rd_req_size(struct meson_pcie *mp, int size) +{ + u32 val; + int max_rd_req_size = meson_size_to_payload(mp, size); + + val = meson_elb_readl(mp, PCIE_DEV_CTRL_DEV_STUS); + val &= ~PCIE_CAP_MAX_READ_REQ_MASK; + meson_elb_writel(mp, val, PCIE_DEV_CTRL_DEV_STUS); + + val = meson_elb_readl(mp, PCIE_DEV_CTRL_DEV_STUS); + val |= PCIE_CAP_MAX_READ_REQ_SIZE(max_rd_req_size); + meson_elb_writel(mp, val, PCIE_DEV_CTRL_DEV_STUS); +} + +static inline void meson_enable_memory_space(struct meson_pcie *mp) +{ + /* Set the RC Bus Master, Memory Space and I/O Space enables */ + meson_elb_writel(mp, PCI_IO_EN | PCI_MEM_SPACE_EN | PCI_BUS_MASTER_EN, + PCIE_STATUS_COMMAND); +} + +static int meson_pcie_establish_link(struct meson_pcie *mp) +{ + struct dw_pcie *pci = &mp->pci; + struct pcie_port *pp = &pci->pp; + + meson_pcie_init_dw(mp); + meson_set_max_payload(mp, MAX_PAYLOAD_SIZE); + meson_set_max_rd_req_size(mp, MAX_READ_REQ_SIZE); + + dw_pcie_setup_rc(pp); + meson_enable_memory_space(mp); + + meson_pcie_assert_reset(mp); + + return dw_pcie_wait_for_link(pci); +} + +static void meson_pcie_enable_interrupts(struct meson_pcie *mp) +{ + if (IS_ENABLED(CONFIG_PCI_MSI)) + dw_pcie_msi_init(&mp->pci.pp); +} + +static int meson_pcie_rd_own_conf(struct pcie_port *pp, int where, int size, + u32 *val) +{ + struct dw_pcie *pci = to_dw_pcie_from_pp(pp); + int ret; + + ret = dw_pcie_read(pci->dbi_base + where, size, val); + if (ret != PCIBIOS_SUCCESSFUL) + return ret; + + /* + * There is a bug in the MESON AXG PCIe controller whereby software + * cannot program the PCI_CLASS_DEVICE register, so we must fabricate + * the return value in the config accessors. + */ + if (where == PCI_CLASS_REVISION && size == 4) + *val = (PCI_CLASS_BRIDGE_PCI << 16) | (*val & 0xffff); + else if (where == PCI_CLASS_DEVICE && size == 2) + *val = PCI_CLASS_BRIDGE_PCI; + else if (where == PCI_CLASS_DEVICE && size == 1) + *val = PCI_CLASS_BRIDGE_PCI & 0xff; + else if (where == PCI_CLASS_DEVICE + 1 && size == 1) + *val = (PCI_CLASS_BRIDGE_PCI >> 8) & 0xff; + + return PCIBIOS_SUCCESSFUL; +} + +static int meson_pcie_wr_own_conf(struct pcie_port *pp, int where, + int size, u32 val) +{ + struct dw_pcie *pci = to_dw_pcie_from_pp(pp); + + return dw_pcie_write(pci->dbi_base + where, size, val); +} + +static int meson_pcie_link_up(struct dw_pcie *pci) +{ + struct meson_pcie *mp = to_meson_pcie(pci); + struct device *dev = pci->dev; + u32 speed_okay = 0; + u32 cnt = 0; + u32 state12, state17, smlh_up, ltssm_up, rdlh_up; + + do { + state12 = meson_cfg_readl(mp, PCIE_CFG_STATUS12); + state17 = meson_cfg_readl(mp, PCIE_CFG_STATUS17); + smlh_up = IS_SMLH_LINK_UP(state12); + rdlh_up = IS_RDLH_LINK_UP(state12); + ltssm_up = IS_LTSSM_UP(state12); + + if (PM_CURRENT_STATE(state17) < PCIE_GEN3) + speed_okay = 1; + + if (smlh_up) + dev_dbg(dev, "smlh_link_up is on\n"); + if (rdlh_up) + dev_dbg(dev, "rdlh_link_up is on\n"); + if (ltssm_up) + dev_dbg(dev, "ltssm_up is on\n"); + if (speed_okay) + dev_dbg(dev, "speed_okay\n"); + + if (smlh_up && rdlh_up && ltssm_up && speed_okay) + return 1; + + cnt++; + + udelay(10); + } while (cnt < WAIT_LINKUP_TIMEOUT); + + dev_err(dev, "error: wait linkup timeout\n"); + return 0; +} + +static int meson_pcie_host_init(struct pcie_port *pp) +{ + struct dw_pcie *pci = to_dw_pcie_from_pp(pp); + struct meson_pcie *mp = to_meson_pcie(pci); + int ret; + + ret = meson_pcie_establish_link(mp); + if (ret) + return ret; + + meson_pcie_enable_interrupts(mp); + + return 0; +} + +static const struct dw_pcie_host_ops meson_pcie_host_ops = { + .rd_own_conf = meson_pcie_rd_own_conf, + .wr_own_conf = meson_pcie_wr_own_conf, + .host_init = meson_pcie_host_init, +}; + +static int meson_add_pcie_port(struct meson_pcie *mp, + struct platform_device *pdev) +{ + struct dw_pcie *pci = &mp->pci; + struct pcie_port *pp = &pci->pp; + struct device *dev = &pdev->dev; + int ret; + + if (IS_ENABLED(CONFIG_PCI_MSI)) { + pp->msi_irq = platform_get_irq(pdev, 0); + if (pp->msi_irq < 0) { + dev_err(dev, "failed to get MSI IRQ\n"); + return pp->msi_irq; + } + } + + pp->ops = &meson_pcie_host_ops; + pci->dbi_base = mp->mem_res.elbi_base; + + ret = dw_pcie_host_init(pp); + if (ret) { + dev_err(dev, "failed to initialize host\n"); + return ret; + } + + return 0; +} + +static const struct dw_pcie_ops dw_pcie_ops = { + .link_up = meson_pcie_link_up, +}; + +static int meson_pcie_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct dw_pcie *pci; + struct meson_pcie *mp; + int ret; + + mp = devm_kzalloc(dev, sizeof(*mp), GFP_KERNEL); + if (!mp) + return -ENOMEM; + + pci = &mp->pci; + pci->dev = dev; + pci->ops = &dw_pcie_ops; + + mp->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW); + if (IS_ERR(mp->reset_gpio)) { + dev_err(dev, "get reset gpio failed\n"); + return PTR_ERR(mp->reset_gpio); + } + + ret = meson_pcie_get_resets(mp); + if (ret) { + dev_err(dev, "get reset resource failed, %d\n", ret); + return ret; + } + + ret = meson_pcie_get_mems(pdev, mp); + if (ret) { + dev_err(dev, "get memory resource failed, %d\n", ret); + return ret; + } + + meson_pcie_power_on(mp); + meson_pcie_reset(mp); + + ret = meson_pcie_probe_clocks(mp); + if (ret) { + dev_err(dev, "init clock resources failed, %d\n", ret); + return ret; + } + + platform_set_drvdata(pdev, mp); + + ret = meson_add_pcie_port(mp, pdev); + if (ret < 0) { + dev_err(dev, "Add PCIe port failed, %d\n", ret); + return ret; + } + + return 0; +} + +static const struct of_device_id meson_pcie_of_match[] = { + { + .compatible = "amlogic,axg-pcie", + }, + {}, +}; + +static struct platform_driver meson_pcie_driver = { + .probe = meson_pcie_probe, + .driver = { + .name = "meson-pcie", + .of_match_table = meson_pcie_of_match, + }, +}; + +builtin_platform_driver(meson_pcie_driver); diff --git a/drivers/pci/controller/dwc/pcie-armada8k.c b/drivers/pci/controller/dwc/pcie-armada8k.c index 0c389a30ef5d..b171b6bc15c8 100644 --- a/drivers/pci/controller/dwc/pcie-armada8k.c +++ b/drivers/pci/controller/dwc/pcie-armada8k.c @@ -22,6 +22,7 @@ #include <linux/resource.h> #include <linux/of_pci.h> #include <linux/of_irq.h> +#include <linux/gpio/consumer.h> #include "pcie-designware.h" @@ -29,6 +30,7 @@ struct armada8k_pcie { struct dw_pcie *pci; struct clk *clk; struct clk *clk_reg; + struct gpio_desc *reset_gpio; }; #define PCIE_VENDOR_REGS_OFFSET 0x8000 @@ -137,6 +139,12 @@ static int armada8k_pcie_host_init(struct pcie_port *pp) struct dw_pcie *pci = to_dw_pcie_from_pp(pp); struct armada8k_pcie *pcie = to_armada8k_pcie(pci); + if (pcie->reset_gpio) { + /* assert and then deassert the reset signal */ + gpiod_set_value_cansleep(pcie->reset_gpio, 1); + msleep(100); + gpiod_set_value_cansleep(pcie->reset_gpio, 0); + } dw_pcie_setup_rc(pp); armada8k_pcie_establish_link(pcie); @@ -249,6 +257,14 @@ static int armada8k_pcie_probe(struct platform_device *pdev) goto fail_clkreg; } + /* Get reset gpio signal and hold asserted (logically high) */ + pcie->reset_gpio = devm_gpiod_get_optional(dev, "reset", + GPIOD_OUT_HIGH); + if (IS_ERR(pcie->reset_gpio)) { + ret = PTR_ERR(pcie->reset_gpio); + goto fail_clkreg; + } + platform_set_drvdata(pdev, pcie); ret = armada8k_add_pcie_port(pcie, pdev); diff --git a/drivers/pci/controller/dwc/pcie-designware-ep.c b/drivers/pci/controller/dwc/pcie-designware-ep.c index 1e7b02221eac..880210366e71 100644 --- a/drivers/pci/controller/dwc/pcie-designware-ep.c +++ b/drivers/pci/controller/dwc/pcie-designware-ep.c @@ -504,6 +504,10 @@ int dw_pcie_ep_init(struct dw_pcie_ep *ep) dev_err(dev, "dbi_base/dbi_base2 is not populated\n"); return -EINVAL; } + if (pci->iatu_unroll_enabled && !pci->atu_base) { + dev_err(dev, "atu_base is not populated\n"); + return -EINVAL; + } ret = of_property_read_u32(np, "num-ib-windows", &ep->num_ib_windows); if (ret < 0) { diff --git a/drivers/pci/controller/dwc/pcie-designware-host.c b/drivers/pci/controller/dwc/pcie-designware-host.c index 29a05759a294..721d60a5d9e4 100644 --- a/drivers/pci/controller/dwc/pcie-designware-host.c +++ b/drivers/pci/controller/dwc/pcie-designware-host.c @@ -99,9 +99,6 @@ irqreturn_t dw_handle_msi_irq(struct pcie_port *pp) (i * MAX_MSI_IRQS_PER_CTRL) + pos); generic_handle_irq(irq); - dw_pcie_wr_own_conf(pp, PCIE_MSI_INTR0_STATUS + - (i * MSI_REG_CTRL_BLOCK_SIZE), - 4, 1 << pos); pos++; } } @@ -168,8 +165,8 @@ static void dw_pci_bottom_mask(struct irq_data *data) bit = data->hwirq % MAX_MSI_IRQS_PER_CTRL; pp->irq_status[ctrl] &= ~(1 << bit); - dw_pcie_wr_own_conf(pp, PCIE_MSI_INTR0_ENABLE + res, 4, - pp->irq_status[ctrl]); + dw_pcie_wr_own_conf(pp, PCIE_MSI_INTR0_MASK + res, 4, + ~pp->irq_status[ctrl]); } raw_spin_unlock_irqrestore(&pp->lock, flags); @@ -191,8 +188,8 @@ static void dw_pci_bottom_unmask(struct irq_data *data) bit = data->hwirq % MAX_MSI_IRQS_PER_CTRL; pp->irq_status[ctrl] |= 1 << bit; - dw_pcie_wr_own_conf(pp, PCIE_MSI_INTR0_ENABLE + res, 4, - pp->irq_status[ctrl]); + dw_pcie_wr_own_conf(pp, PCIE_MSI_INTR0_MASK + res, 4, + ~pp->irq_status[ctrl]); } raw_spin_unlock_irqrestore(&pp->lock, flags); @@ -200,13 +197,22 @@ static void dw_pci_bottom_unmask(struct irq_data *data) static void dw_pci_bottom_ack(struct irq_data *d) { - struct msi_desc *msi = irq_data_get_msi_desc(d); - struct pcie_port *pp; + struct pcie_port *pp = irq_data_get_irq_chip_data(d); + unsigned int res, bit, ctrl; + unsigned long flags; + + ctrl = d->hwirq / MAX_MSI_IRQS_PER_CTRL; + res = ctrl * MSI_REG_CTRL_BLOCK_SIZE; + bit = d->hwirq % MAX_MSI_IRQS_PER_CTRL; + + raw_spin_lock_irqsave(&pp->lock, flags); - pp = msi_desc_to_pci_sysdata(msi); + dw_pcie_wr_own_conf(pp, PCIE_MSI_INTR0_STATUS + res, 4, 1 << bit); if (pp->ops->msi_irq_ack) pp->ops->msi_irq_ack(d->hwirq, pp); + + raw_spin_unlock_irqrestore(&pp->lock, flags); } static struct irq_chip dw_pci_msi_bottom_irq_chip = { @@ -658,10 +664,15 @@ void dw_pcie_setup_rc(struct pcie_port *pp) num_ctrls = pp->num_vectors / MAX_MSI_IRQS_PER_CTRL; /* Initialize IRQ Status array */ - for (ctrl = 0; ctrl < num_ctrls; ctrl++) - dw_pcie_rd_own_conf(pp, PCIE_MSI_INTR0_ENABLE + + for (ctrl = 0; ctrl < num_ctrls; ctrl++) { + dw_pcie_wr_own_conf(pp, PCIE_MSI_INTR0_MASK + + (ctrl * MSI_REG_CTRL_BLOCK_SIZE), + 4, ~0); + dw_pcie_wr_own_conf(pp, PCIE_MSI_INTR0_ENABLE + (ctrl * MSI_REG_CTRL_BLOCK_SIZE), - 4, &pp->irq_status[ctrl]); + 4, ~0); + pp->irq_status[ctrl] = 0; + } /* Setup RC BARs */ dw_pcie_writel_dbi(pci, PCI_BASE_ADDRESS_0, 0x00000004); @@ -699,6 +710,9 @@ void dw_pcie_setup_rc(struct pcie_port *pp) dev_dbg(pci->dev, "iATU unroll: %s\n", pci->iatu_unroll_enabled ? "enabled" : "disabled"); + if (pci->iatu_unroll_enabled && !pci->atu_base) + pci->atu_base = pci->dbi_base + DEFAULT_DBI_ATU_OFFSET; + dw_pcie_prog_outbound_atu(pci, PCIE_ATU_REGION_INDEX0, PCIE_ATU_TYPE_MEM, pp->mem_base, pp->mem_bus_addr, pp->mem_size); diff --git a/drivers/pci/controller/dwc/pcie-designware.c b/drivers/pci/controller/dwc/pcie-designware.c index 2153956a0b20..93ef8c31fb39 100644 --- a/drivers/pci/controller/dwc/pcie-designware.c +++ b/drivers/pci/controller/dwc/pcie-designware.c @@ -93,7 +93,7 @@ static u32 dw_pcie_readl_ob_unroll(struct dw_pcie *pci, u32 index, u32 reg) { u32 offset = PCIE_GET_ATU_OUTB_UNR_REG_OFFSET(index); - return dw_pcie_readl_dbi(pci, offset + reg); + return dw_pcie_readl_atu(pci, offset + reg); } static void dw_pcie_writel_ob_unroll(struct dw_pcie *pci, u32 index, u32 reg, @@ -101,7 +101,7 @@ static void dw_pcie_writel_ob_unroll(struct dw_pcie *pci, u32 index, u32 reg, { u32 offset = PCIE_GET_ATU_OUTB_UNR_REG_OFFSET(index); - dw_pcie_writel_dbi(pci, offset + reg, val); + dw_pcie_writel_atu(pci, offset + reg, val); } static void dw_pcie_prog_outbound_atu_unroll(struct dw_pcie *pci, int index, @@ -187,7 +187,7 @@ static u32 dw_pcie_readl_ib_unroll(struct dw_pcie *pci, u32 index, u32 reg) { u32 offset = PCIE_GET_ATU_INB_UNR_REG_OFFSET(index); - return dw_pcie_readl_dbi(pci, offset + reg); + return dw_pcie_readl_atu(pci, offset + reg); } static void dw_pcie_writel_ib_unroll(struct dw_pcie *pci, u32 index, u32 reg, @@ -195,7 +195,7 @@ static void dw_pcie_writel_ib_unroll(struct dw_pcie *pci, u32 index, u32 reg, { u32 offset = PCIE_GET_ATU_INB_UNR_REG_OFFSET(index); - dw_pcie_writel_dbi(pci, offset + reg, val); + dw_pcie_writel_atu(pci, offset + reg, val); } static int dw_pcie_prog_inbound_atu_unroll(struct dw_pcie *pci, int index, diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h index 0989d880ac46..9943d8c68335 100644 --- a/drivers/pci/controller/dwc/pcie-designware.h +++ b/drivers/pci/controller/dwc/pcie-designware.h @@ -92,12 +92,20 @@ #define PCIE_ATU_UNR_LOWER_TARGET 0x14 #define PCIE_ATU_UNR_UPPER_TARGET 0x18 +/* + * The default address offset between dbi_base and atu_base. Root controller + * drivers are not required to initialize atu_base if the offset matches this + * default; the driver core automatically derives atu_base from dbi_base using + * this offset, if atu_base not set. + */ +#define DEFAULT_DBI_ATU_OFFSET (0x3 << 20) + /* Register address builder */ -#define PCIE_GET_ATU_OUTB_UNR_REG_OFFSET(region) \ - ((0x3 << 20) | ((region) << 9)) +#define PCIE_GET_ATU_OUTB_UNR_REG_OFFSET(region) \ + ((region) << 9) -#define PCIE_GET_ATU_INB_UNR_REG_OFFSET(region) \ - ((0x3 << 20) | ((region) << 9) | (0x1 << 8)) +#define PCIE_GET_ATU_INB_UNR_REG_OFFSET(region) \ + (((region) << 9) | (0x1 << 8)) #define MAX_MSI_IRQS 256 #define MAX_MSI_IRQS_PER_CTRL 32 @@ -219,6 +227,8 @@ struct dw_pcie { struct device *dev; void __iomem *dbi_base; void __iomem *dbi_base2; + /* Used when iatu_unroll_enabled is true */ + void __iomem *atu_base; u32 num_viewport; u8 iatu_unroll_enabled; struct pcie_port pp; @@ -289,6 +299,16 @@ static inline u32 dw_pcie_readl_dbi2(struct dw_pcie *pci, u32 reg) return __dw_pcie_read_dbi(pci, pci->dbi_base2, reg, 0x4); } +static inline void dw_pcie_writel_atu(struct dw_pcie *pci, u32 reg, u32 val) +{ + __dw_pcie_write_dbi(pci, pci->atu_base, reg, 0x4, val); +} + +static inline u32 dw_pcie_readl_atu(struct dw_pcie *pci, u32 reg) +{ + return __dw_pcie_read_dbi(pci, pci->atu_base, reg, 0x4); +} + static inline void dw_pcie_dbi_ro_wr_en(struct dw_pcie *pci) { u32 reg; diff --git a/drivers/pci/controller/dwc/pcie-histb.c b/drivers/pci/controller/dwc/pcie-histb.c index 7b32e619b959..954bc2b74bbc 100644 --- a/drivers/pci/controller/dwc/pcie-histb.c +++ b/drivers/pci/controller/dwc/pcie-histb.c @@ -202,7 +202,7 @@ static int histb_pcie_host_init(struct pcie_port *pp) return 0; } -static struct dw_pcie_host_ops histb_pcie_host_ops = { +static const struct dw_pcie_host_ops histb_pcie_host_ops = { .rd_own_conf = histb_pcie_rd_own_conf, .wr_own_conf = histb_pcie_wr_own_conf, .host_init = histb_pcie_host_init, diff --git a/drivers/pci/controller/pcie-mediatek.c b/drivers/pci/controller/pcie-mediatek.c index d069a76cbb95..55e471c18e8d 100644 --- a/drivers/pci/controller/pcie-mediatek.c +++ b/drivers/pci/controller/pcie-mediatek.c @@ -161,7 +161,6 @@ struct mtk_pcie_soc { * @obff_ck: pointer to OBFF functional block operating clock * @pipe_ck: pointer to LTSSM and PHY/MAC layer operating clock * @phy: pointer to PHY control block - * @lane: lane count * @slot: port slot * @irq: GIC irq * @irq_domain: legacy INTx IRQ domain @@ -182,7 +181,6 @@ struct mtk_pcie_port { struct clk *obff_ck; struct clk *pipe_ck; struct phy *phy; - u32 lane; u32 slot; int irq; struct irq_domain *irq_domain; @@ -197,29 +195,20 @@ struct mtk_pcie_port { * @dev: pointer to PCIe device * @base: IO mapped register base * @free_ck: free-run reference clock - * @io: IO resource - * @pio: PIO resource * @mem: non-prefetchable memory resource - * @busn: bus range - * @offset: IO / Memory offset * @ports: pointer to PCIe port information * @soc: pointer to SoC-dependent operations + * @busnr: root bus number */ struct mtk_pcie { struct device *dev; void __iomem *base; struct clk *free_ck; - struct resource io; - struct resource pio; struct resource mem; - struct resource busn; - struct { - resource_size_t mem; - resource_size_t io; - } offset; struct list_head ports; const struct mtk_pcie_soc *soc; + unsigned int busnr; }; static void mtk_pcie_subsys_powerdown(struct mtk_pcie *pcie) @@ -904,12 +893,6 @@ static int mtk_pcie_parse_port(struct mtk_pcie *pcie, if (!port) return -ENOMEM; - err = of_property_read_u32(node, "num-lanes", &port->lane); - if (err) { - dev_err(dev, "missing num-lanes property\n"); - return err; - } - snprintf(name, sizeof(name), "port%d", slot); regs = platform_get_resource_byname(pdev, IORESOURCE_MEM, name); port->base = devm_ioremap_resource(dev, regs); @@ -1045,55 +1028,43 @@ static int mtk_pcie_setup(struct mtk_pcie *pcie) { struct device *dev = pcie->dev; struct device_node *node = dev->of_node, *child; - struct of_pci_range_parser parser; - struct of_pci_range range; - struct resource res; struct mtk_pcie_port *port, *tmp; + struct pci_host_bridge *host = pci_host_bridge_from_priv(pcie); + struct list_head *windows = &host->windows; + struct resource_entry *win, *tmp_win; + resource_size_t io_base; int err; - if (of_pci_range_parser_init(&parser, node)) { - dev_err(dev, "missing \"ranges\" property\n"); - return -EINVAL; - } + err = devm_of_pci_get_host_bridge_resources(dev, 0, 0xff, + windows, &io_base); + if (err) + return err; - for_each_of_pci_range(&parser, &range) { - err = of_pci_range_to_resource(&range, node, &res); - if (err < 0) - return err; + err = devm_request_pci_bus_resources(dev, windows); + if (err < 0) + return err; - switch (res.flags & IORESOURCE_TYPE_BITS) { + /* Get the I/O and memory ranges from DT */ + resource_list_for_each_entry_safe(win, tmp_win, windows) { + switch (resource_type(win->res)) { case IORESOURCE_IO: - pcie->offset.io = res.start - range.pci_addr; - - memcpy(&pcie->pio, &res, sizeof(res)); - pcie->pio.name = node->full_name; - - pcie->io.start = range.cpu_addr; - pcie->io.end = range.cpu_addr + range.size - 1; - pcie->io.flags = IORESOURCE_MEM; - pcie->io.name = "I/O"; - - memcpy(&res, &pcie->io, sizeof(res)); + err = devm_pci_remap_iospace(dev, win->res, io_base); + if (err) { + dev_warn(dev, "error %d: failed to map resource %pR\n", + err, win->res); + resource_list_destroy_entry(win); + } break; - case IORESOURCE_MEM: - pcie->offset.mem = res.start - range.pci_addr; - - memcpy(&pcie->mem, &res, sizeof(res)); + memcpy(&pcie->mem, win->res, sizeof(*win->res)); pcie->mem.name = "non-prefetchable"; break; + case IORESOURCE_BUS: + pcie->busnr = win->res->start; + break; } } - err = of_pci_parse_bus_range(node, &pcie->busn); - if (err < 0) { - dev_err(dev, "failed to parse bus ranges property: %d\n", err); - pcie->busn.name = node->name; - pcie->busn.start = 0; - pcie->busn.end = 0xff; - pcie->busn.flags = IORESOURCE_BUS; - } - for_each_available_child_of_node(node, child) { int slot; @@ -1125,28 +1096,6 @@ static int mtk_pcie_setup(struct mtk_pcie *pcie) return 0; } -static int mtk_pcie_request_resources(struct mtk_pcie *pcie) -{ - struct pci_host_bridge *host = pci_host_bridge_from_priv(pcie); - struct list_head *windows = &host->windows; - struct device *dev = pcie->dev; - int err; - - pci_add_resource_offset(windows, &pcie->pio, pcie->offset.io); - pci_add_resource_offset(windows, &pcie->mem, pcie->offset.mem); - pci_add_resource(windows, &pcie->busn); - - err = devm_request_pci_bus_resources(dev, windows); - if (err < 0) - return err; - - err = devm_pci_remap_iospace(dev, &pcie->pio, pcie->io.start); - if (err) - return err; - - return 0; -} - static int mtk_pcie_probe(struct platform_device *pdev) { struct device *dev = &pdev->dev; @@ -1169,11 +1118,7 @@ static int mtk_pcie_probe(struct platform_device *pdev) if (err) return err; - err = mtk_pcie_request_resources(pcie); - if (err) - goto put_resources; - - host->busnr = pcie->busn.start; + host->busnr = pcie->busnr; host->dev.parent = pcie->dev; host->ops = pcie->soc->ops; host->map_irq = of_irq_parse_and_map_pci; diff --git a/drivers/pci/iov.c b/drivers/pci/iov.c index 9616eca3182f..3aa115ed3a65 100644 --- a/drivers/pci/iov.c +++ b/drivers/pci/iov.c @@ -252,6 +252,27 @@ int __weak pcibios_sriov_disable(struct pci_dev *pdev) return 0; } +static int sriov_add_vfs(struct pci_dev *dev, u16 num_vfs) +{ + unsigned int i; + int rc; + + if (dev->no_vf_scan) + return 0; + + for (i = 0; i < num_vfs; i++) { + rc = pci_iov_add_virtfn(dev, i); + if (rc) + goto failed; + } + return 0; +failed: + while (i--) + pci_iov_remove_virtfn(dev, i); + + return rc; +} + static int sriov_enable(struct pci_dev *dev, int nr_virtfn) { int rc; @@ -337,21 +358,15 @@ static int sriov_enable(struct pci_dev *dev, int nr_virtfn) msleep(100); pci_cfg_access_unlock(dev); - for (i = 0; i < initial; i++) { - rc = pci_iov_add_virtfn(dev, i); - if (rc) - goto failed; - } + rc = sriov_add_vfs(dev, initial); + if (rc) + goto err_pcibios; kobject_uevent(&dev->dev.kobj, KOBJ_CHANGE); iov->num_VFs = nr_virtfn; return 0; -failed: - while (i--) - pci_iov_remove_virtfn(dev, i); - err_pcibios: iov->ctrl &= ~(PCI_SRIOV_CTRL_VFE | PCI_SRIOV_CTRL_MSE); pci_cfg_access_lock(dev); @@ -368,17 +383,26 @@ err_pcibios: return rc; } -static void sriov_disable(struct pci_dev *dev) +static void sriov_del_vfs(struct pci_dev *dev) { - int i; struct pci_sriov *iov = dev->sriov; + int i; - if (!iov->num_VFs) + if (dev->no_vf_scan) return; for (i = 0; i < iov->num_VFs; i++) pci_iov_remove_virtfn(dev, i); +} + +static void sriov_disable(struct pci_dev *dev) +{ + struct pci_sriov *iov = dev->sriov; + + if (!iov->num_VFs) + return; + sriov_del_vfs(dev); iov->ctrl &= ~(PCI_SRIOV_CTRL_VFE | PCI_SRIOV_CTRL_MSE); pci_cfg_access_lock(dev); pci_write_config_word(dev, iov->pos + PCI_SRIOV_CTRL, iov->ctrl); diff --git a/drivers/pci/p2pdma.c b/drivers/pci/p2pdma.c index ae3c5b25dcc7..c25a69fc4fc7 100644 --- a/drivers/pci/p2pdma.c +++ b/drivers/pci/p2pdma.c @@ -422,7 +422,7 @@ static int upstream_bridge_distance_warn(struct pci_dev *provider, * * Returns -1 if any of the clients are not compatible (behind the same * root port as the provider), otherwise returns a positive number where - * a lower number is the preferrable choice. (If there's one client + * a lower number is the preferable choice. (If there's one client * that's the same as the provider it will return 0, which is best choice). * * For now, "compatible" means the provider and the clients are all behind @@ -493,7 +493,7 @@ EXPORT_SYMBOL_GPL(pci_has_p2pmem); * @num_clients: number of client devices in the list * * If multiple devices are behind the same switch, the one "closest" to the - * client devices in use will be chosen first. (So if one of the providers are + * client devices in use will be chosen first. (So if one of the providers is * the same as one of the clients, that provider will be used ahead of any * other providers that are unrelated). If multiple providers are an equal * distance away, one will be chosen at random. @@ -580,7 +580,7 @@ EXPORT_SYMBOL_GPL(pci_alloc_p2pmem); * pci_free_p2pmem - free peer-to-peer DMA memory * @pdev: the device the memory was allocated from * @addr: address of the memory that was allocated - * @size: number of bytes that was allocated + * @size: number of bytes that were allocated */ void pci_free_p2pmem(struct pci_dev *pdev, void *addr, size_t size) { @@ -617,7 +617,7 @@ EXPORT_SYMBOL_GPL(pci_p2pmem_virt_to_bus); * @nents: the number of SG entries in the list * @length: number of bytes to allocate * - * Returns 0 on success + * Return: %NULL on error or &struct scatterlist pointer and @nents on success */ struct scatterlist *pci_p2pmem_alloc_sgl(struct pci_dev *pdev, unsigned int *nents, u32 length) @@ -673,7 +673,7 @@ EXPORT_SYMBOL_GPL(pci_p2pmem_free_sgl); * * Published memory can be used by other PCI device drivers for * peer-2-peer DMA operations. Non-published memory is reserved for - * exlusive use of the device driver that registers the peer-to-peer + * exclusive use of the device driver that registers the peer-to-peer * memory. */ void pci_p2pmem_publish(struct pci_dev *pdev, bool publish) @@ -733,7 +733,7 @@ EXPORT_SYMBOL_GPL(pci_p2pdma_map_sg); * @use_p2pdma: returns whether to enable p2pdma or not * * Parses an attribute value to decide whether to enable p2pdma. - * The value can select a PCI device (using it's full BDF device + * The value can select a PCI device (using its full BDF device * name) or a boolean (in any format strtobool() accepts). A false * value disables p2pdma, a true value expects the caller * to automatically find a compatible device and specifying a PCI device @@ -784,7 +784,7 @@ EXPORT_SYMBOL_GPL(pci_p2pdma_enable_store); * whether p2pdma is enabled * @page: contents of the stored value * @p2p_dev: the selected p2p device (NULL if no device is selected) - * @use_p2pdma: whether p2pdme has been enabled + * @use_p2pdma: whether p2pdma has been enabled * * Attributes that use pci_p2pdma_enable_store() should use this function * to show the value of the attribute. diff --git a/drivers/pci/pci-driver.c b/drivers/pci/pci-driver.c index bef17c3fca67..33f3f475e5c6 100644 --- a/drivers/pci/pci-driver.c +++ b/drivers/pci/pci-driver.c @@ -1251,30 +1251,29 @@ static int pci_pm_runtime_suspend(struct device *dev) return 0; } - if (!pm || !pm->runtime_suspend) - return -ENOSYS; - pci_dev->state_saved = false; - error = pm->runtime_suspend(dev); - if (error) { + if (pm && pm->runtime_suspend) { + error = pm->runtime_suspend(dev); /* * -EBUSY and -EAGAIN is used to request the runtime PM core * to schedule a new suspend, so log the event only with debug * log level. */ - if (error == -EBUSY || error == -EAGAIN) + if (error == -EBUSY || error == -EAGAIN) { dev_dbg(dev, "can't suspend now (%pf returned %d)\n", pm->runtime_suspend, error); - else + return error; + } else if (error) { dev_err(dev, "can't suspend (%pf returned %d)\n", pm->runtime_suspend, error); - - return error; + return error; + } } pci_fixup_device(pci_fixup_suspend, pci_dev); - if (!pci_dev->state_saved && pci_dev->current_state != PCI_D0 + if (pm && pm->runtime_suspend + && !pci_dev->state_saved && pci_dev->current_state != PCI_D0 && pci_dev->current_state != PCI_UNKNOWN) { WARN_ONCE(pci_dev->current_state != prev, "PCI PM: State of device not saved by %pF\n", @@ -1292,7 +1291,7 @@ static int pci_pm_runtime_suspend(struct device *dev) static int pci_pm_runtime_resume(struct device *dev) { - int rc; + int rc = 0; struct pci_dev *pci_dev = to_pci_dev(dev); const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL; @@ -1306,14 +1305,12 @@ static int pci_pm_runtime_resume(struct device *dev) if (!pci_dev->driver) return 0; - if (!pm || !pm->runtime_resume) - return -ENOSYS; - pci_fixup_device(pci_fixup_resume_early, pci_dev); pci_enable_wake(pci_dev, PCI_D0, false); pci_fixup_device(pci_fixup_resume, pci_dev); - rc = pm->runtime_resume(dev); + if (pm && pm->runtime_resume) + rc = pm->runtime_resume(dev); pci_dev->runtime_d3cold = false; diff --git a/drivers/pci/pci.h b/drivers/pci/pci.h index 662b7457db23..224d88634115 100644 --- a/drivers/pci/pci.h +++ b/drivers/pci/pci.h @@ -2,6 +2,8 @@ #ifndef DRIVERS_PCI_H #define DRIVERS_PCI_H +#include <linux/pci.h> + #define PCI_FIND_CAP_TTL 48 #define PCI_VSEC_ID_INTEL_TBT 0x1234 /* Thunderbolt */ diff --git a/drivers/pci/pcie/aspm.c b/drivers/pci/pcie/aspm.c index dcb29cb76dc6..2330ebf6df72 100644 --- a/drivers/pci/pcie/aspm.c +++ b/drivers/pci/pcie/aspm.c @@ -53,8 +53,6 @@ struct pcie_link_state { struct pcie_link_state *root; /* pointer to the root port link */ struct pcie_link_state *parent; /* pointer to the parent Link state */ struct list_head sibling; /* node in link_list */ - struct list_head children; /* list of child link states */ - struct list_head link; /* node in parent's children list */ /* ASPM state */ u32 aspm_support:7; /* Supported ASPM state */ @@ -850,8 +848,6 @@ static struct pcie_link_state *alloc_pcie_link_state(struct pci_dev *pdev) return NULL; INIT_LIST_HEAD(&link->sibling); - INIT_LIST_HEAD(&link->children); - INIT_LIST_HEAD(&link->link); link->pdev = pdev; link->downstream = pci_function_0(pdev->subordinate); @@ -877,7 +873,6 @@ static struct pcie_link_state *alloc_pcie_link_state(struct pci_dev *pdev) link->parent = parent; link->root = link->parent->root; - list_add(&link->link, &parent->children); } list_add(&link->sibling, &link_list); @@ -1001,7 +996,6 @@ void pcie_aspm_exit_link_state(struct pci_dev *pdev) /* All functions are removed, so just disable ASPM for the link */ pcie_config_aspm_link(link, 0); list_del(&link->sibling); - list_del(&link->link); /* Clock PM is for endpoint device */ free_link_state(link); diff --git a/drivers/pci/pcie/portdrv.h b/drivers/pci/pcie/portdrv.h index e495f04394d0..fbbf00b0992e 100644 --- a/drivers/pci/pcie/portdrv.h +++ b/drivers/pci/pcie/portdrv.h @@ -71,19 +71,19 @@ static inline void *get_service_data(struct pcie_device *dev) struct pcie_port_service_driver { const char *name; - int (*probe) (struct pcie_device *dev); - void (*remove) (struct pcie_device *dev); - int (*suspend) (struct pcie_device *dev); - int (*resume_noirq) (struct pcie_device *dev); - int (*resume) (struct pcie_device *dev); - int (*runtime_suspend) (struct pcie_device *dev); - int (*runtime_resume) (struct pcie_device *dev); + int (*probe)(struct pcie_device *dev); + void (*remove)(struct pcie_device *dev); + int (*suspend)(struct pcie_device *dev); + int (*resume_noirq)(struct pcie_device *dev); + int (*resume)(struct pcie_device *dev); + int (*runtime_suspend)(struct pcie_device *dev); + int (*runtime_resume)(struct pcie_device *dev); /* Device driver may resume normal operations */ void (*error_resume)(struct pci_dev *dev); /* Link Reset Capability - AER service driver specific */ - pci_ers_result_t (*reset_link) (struct pci_dev *dev); + pci_ers_result_t (*reset_link)(struct pci_dev *dev); int port_type; /* Type of the port this driver can handle */ u32 service; /* Port service this device represents */ diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c index 4700d24e5d55..b0a413f3f7ca 100644 --- a/drivers/pci/quirks.c +++ b/drivers/pci/quirks.c @@ -619,6 +619,30 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_NL_USB, quirk_amd_nl_class); /* + * Synopsys USB 3.x host HAPS platform has a class code of + * PCI_CLASS_SERIAL_USB_XHCI, and xhci driver can claim it. However, these + * devices should use dwc3-haps driver. Change these devices' class code to + * PCI_CLASS_SERIAL_USB_DEVICE to prevent the xhci-pci driver from claiming + * them. + */ +static void quirk_synopsys_haps(struct pci_dev *pdev) +{ + u32 class = pdev->class; + + switch (pdev->device) { + case PCI_DEVICE_ID_SYNOPSYS_HAPSUSB3: + case PCI_DEVICE_ID_SYNOPSYS_HAPSUSB3_AXI: + case PCI_DEVICE_ID_SYNOPSYS_HAPSUSB31: + pdev->class = PCI_CLASS_SERIAL_USB_DEVICE; + pci_info(pdev, "PCI class overridden (%#08x -> %#08x) so dwc3 driver can claim this instead of xhci\n", + class, pdev->class); + break; + } +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SYNOPSYS, PCI_ANY_ID, + quirk_synopsys_haps); + +/* * Let's make the southbridge information explicit instead of having to * worry about people probing the ACPI areas, for example.. (Yes, it * happens, and if you read the wrong ACPI register it will put the machine diff --git a/drivers/pci/switch/switchtec.c b/drivers/pci/switch/switchtec.c index 54a8b30dda38..6c5536d3d42a 100644 --- a/drivers/pci/switch/switchtec.c +++ b/drivers/pci/switch/switchtec.c @@ -13,7 +13,7 @@ #include <linux/uaccess.h> #include <linux/poll.h> #include <linux/wait.h> - +#include <linux/io-64-nonatomic-lo-hi.h> #include <linux/nospec.h> MODULE_DESCRIPTION("Microsemi Switchtec(tm) PCIe Management Driver"); @@ -25,6 +25,11 @@ static int max_devices = 16; module_param(max_devices, int, 0644); MODULE_PARM_DESC(max_devices, "max number of switchtec device instances"); +static bool use_dma_mrpc = 1; +module_param(use_dma_mrpc, bool, 0644); +MODULE_PARM_DESC(use_dma_mrpc, + "Enable the use of the DMA MRPC feature"); + static dev_t switchtec_devt; static DEFINE_IDA(switchtec_minor_ida); @@ -113,6 +118,19 @@ static void stuser_set_state(struct switchtec_user *stuser, static void mrpc_complete_cmd(struct switchtec_dev *stdev); +static void flush_wc_buf(struct switchtec_dev *stdev) +{ + struct ntb_dbmsg_regs __iomem *mmio_dbmsg; + + /* + * odb (outbound doorbell) register is processed by low latency + * hardware and w/o side effect + */ + mmio_dbmsg = (void __iomem *)stdev->mmio_ntb + + SWITCHTEC_NTB_REG_DBMSG_OFFSET; + ioread32(&mmio_dbmsg->odb); +} + static void mrpc_cmd_submit(struct switchtec_dev *stdev) { /* requires the mrpc_mutex to already be held when called */ @@ -128,16 +146,18 @@ static void mrpc_cmd_submit(struct switchtec_dev *stdev) stuser = list_entry(stdev->mrpc_queue.next, struct switchtec_user, list); + if (stdev->dma_mrpc) { + stdev->dma_mrpc->status = SWITCHTEC_MRPC_STATUS_INPROGRESS; + memset(stdev->dma_mrpc->data, 0xFF, SWITCHTEC_MRPC_PAYLOAD_SIZE); + } + stuser_set_state(stuser, MRPC_RUNNING); stdev->mrpc_busy = 1; memcpy_toio(&stdev->mmio_mrpc->input_data, stuser->data, stuser->data_len); + flush_wc_buf(stdev); iowrite32(stuser->cmd, &stdev->mmio_mrpc->cmd); - stuser->status = ioread32(&stdev->mmio_mrpc->status); - if (stuser->status != SWITCHTEC_MRPC_STATUS_INPROGRESS) - mrpc_complete_cmd(stdev); - schedule_delayed_work(&stdev->mrpc_timeout, msecs_to_jiffies(500)); } @@ -170,7 +190,11 @@ static void mrpc_complete_cmd(struct switchtec_dev *stdev) stuser = list_entry(stdev->mrpc_queue.next, struct switchtec_user, list); - stuser->status = ioread32(&stdev->mmio_mrpc->status); + if (stdev->dma_mrpc) + stuser->status = stdev->dma_mrpc->status; + else + stuser->status = ioread32(&stdev->mmio_mrpc->status); + if (stuser->status == SWITCHTEC_MRPC_STATUS_INPROGRESS) return; @@ -180,13 +204,19 @@ static void mrpc_complete_cmd(struct switchtec_dev *stdev) if (stuser->status != SWITCHTEC_MRPC_STATUS_DONE) goto out; - stuser->return_code = ioread32(&stdev->mmio_mrpc->ret_value); + if (stdev->dma_mrpc) + stuser->return_code = stdev->dma_mrpc->rtn_code; + else + stuser->return_code = ioread32(&stdev->mmio_mrpc->ret_value); if (stuser->return_code != 0) goto out; - memcpy_fromio(stuser->data, &stdev->mmio_mrpc->output_data, - stuser->read_len); - + if (stdev->dma_mrpc) + memcpy(stuser->data, &stdev->dma_mrpc->data, + stuser->read_len); + else + memcpy_fromio(stuser->data, &stdev->mmio_mrpc->output_data, + stuser->read_len); out: complete_all(&stuser->comp); list_del_init(&stuser->list); @@ -221,7 +251,10 @@ static void mrpc_timeout_work(struct work_struct *work) mutex_lock(&stdev->mrpc_mutex); - status = ioread32(&stdev->mmio_mrpc->status); + if (stdev->dma_mrpc) + status = stdev->dma_mrpc->status; + else + status = ioread32(&stdev->mmio_mrpc->status); if (status == SWITCHTEC_MRPC_STATUS_INPROGRESS) { schedule_delayed_work(&stdev->mrpc_timeout, msecs_to_jiffies(500)); @@ -229,7 +262,6 @@ static void mrpc_timeout_work(struct work_struct *work) } mrpc_complete_cmd(stdev); - out: mutex_unlock(&stdev->mrpc_mutex); } @@ -800,6 +832,7 @@ static int ioctl_event_ctl(struct switchtec_dev *stdev, { int ret; int nr_idxs; + unsigned int event_flags; struct switchtec_ioctl_event_ctl ctl; if (copy_from_user(&ctl, uctl, sizeof(ctl))) @@ -821,7 +854,9 @@ static int ioctl_event_ctl(struct switchtec_dev *stdev, else return -EINVAL; + event_flags = ctl.flags; for (ctl.index = 0; ctl.index < nr_idxs; ctl.index++) { + ctl.flags = event_flags; ret = event_ctl(stdev, &ctl); if (ret < 0) return ret; @@ -1017,10 +1052,24 @@ static void enable_link_state_events(struct switchtec_dev *stdev) } } +static void enable_dma_mrpc(struct switchtec_dev *stdev) +{ + writeq(stdev->dma_mrpc_dma_addr, &stdev->mmio_mrpc->dma_addr); + flush_wc_buf(stdev); + iowrite32(SWITCHTEC_DMA_MRPC_EN, &stdev->mmio_mrpc->dma_en); +} + static void stdev_release(struct device *dev) { struct switchtec_dev *stdev = to_stdev(dev); + if (stdev->dma_mrpc) { + iowrite32(0, &stdev->mmio_mrpc->dma_en); + flush_wc_buf(stdev); + writeq(0, &stdev->mmio_mrpc->dma_addr); + dma_free_coherent(&stdev->pdev->dev, sizeof(*stdev->dma_mrpc), + stdev->dma_mrpc, stdev->dma_mrpc_dma_addr); + } kfree(stdev); } @@ -1176,10 +1225,27 @@ static irqreturn_t switchtec_event_isr(int irq, void *dev) return ret; } + +static irqreturn_t switchtec_dma_mrpc_isr(int irq, void *dev) +{ + struct switchtec_dev *stdev = dev; + irqreturn_t ret = IRQ_NONE; + + iowrite32(SWITCHTEC_EVENT_CLEAR | + SWITCHTEC_EVENT_EN_IRQ, + &stdev->mmio_part_cfg->mrpc_comp_hdr); + schedule_work(&stdev->mrpc_work); + + ret = IRQ_HANDLED; + return ret; +} + static int switchtec_init_isr(struct switchtec_dev *stdev) { int nvecs; int event_irq; + int dma_mrpc_irq; + int rc; nvecs = pci_alloc_irq_vectors(stdev->pdev, 1, 4, PCI_IRQ_MSIX | PCI_IRQ_MSI); @@ -1194,9 +1260,29 @@ static int switchtec_init_isr(struct switchtec_dev *stdev) if (event_irq < 0) return event_irq; - return devm_request_irq(&stdev->pdev->dev, event_irq, + rc = devm_request_irq(&stdev->pdev->dev, event_irq, switchtec_event_isr, 0, KBUILD_MODNAME, stdev); + + if (rc) + return rc; + + if (!stdev->dma_mrpc) + return rc; + + dma_mrpc_irq = ioread32(&stdev->mmio_mrpc->dma_vector); + if (dma_mrpc_irq < 0 || dma_mrpc_irq >= nvecs) + return -EFAULT; + + dma_mrpc_irq = pci_irq_vector(stdev->pdev, dma_mrpc_irq); + if (dma_mrpc_irq < 0) + return dma_mrpc_irq; + + rc = devm_request_irq(&stdev->pdev->dev, dma_mrpc_irq, + switchtec_dma_mrpc_isr, 0, + KBUILD_MODNAME, stdev); + + return rc; } static void init_pff(struct switchtec_dev *stdev) @@ -1232,19 +1318,38 @@ static int switchtec_init_pci(struct switchtec_dev *stdev, struct pci_dev *pdev) { int rc; + void __iomem *map; + unsigned long res_start, res_len; rc = pcim_enable_device(pdev); if (rc) return rc; - rc = pcim_iomap_regions(pdev, 0x1, KBUILD_MODNAME); + rc = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64)); if (rc) return rc; pci_set_master(pdev); - stdev->mmio = pcim_iomap_table(pdev)[0]; - stdev->mmio_mrpc = stdev->mmio + SWITCHTEC_GAS_MRPC_OFFSET; + res_start = pci_resource_start(pdev, 0); + res_len = pci_resource_len(pdev, 0); + + if (!devm_request_mem_region(&pdev->dev, res_start, + res_len, KBUILD_MODNAME)) + return -EBUSY; + + stdev->mmio_mrpc = devm_ioremap_wc(&pdev->dev, res_start, + SWITCHTEC_GAS_TOP_CFG_OFFSET); + if (!stdev->mmio_mrpc) + return -ENOMEM; + + map = devm_ioremap(&pdev->dev, + res_start + SWITCHTEC_GAS_TOP_CFG_OFFSET, + res_len - SWITCHTEC_GAS_TOP_CFG_OFFSET); + if (!map) + return -ENOMEM; + + stdev->mmio = map - SWITCHTEC_GAS_TOP_CFG_OFFSET; stdev->mmio_sw_event = stdev->mmio + SWITCHTEC_GAS_SW_EVENT_OFFSET; stdev->mmio_sys_info = stdev->mmio + SWITCHTEC_GAS_SYS_INFO_OFFSET; stdev->mmio_flash_info = stdev->mmio + SWITCHTEC_GAS_FLASH_INFO_OFFSET; @@ -1262,6 +1367,19 @@ static int switchtec_init_pci(struct switchtec_dev *stdev, pci_set_drvdata(pdev, stdev); + if (!use_dma_mrpc) + return 0; + + if (ioread32(&stdev->mmio_mrpc->dma_ver) == 0) + return 0; + + stdev->dma_mrpc = dma_zalloc_coherent(&stdev->pdev->dev, + sizeof(*stdev->dma_mrpc), + &stdev->dma_mrpc_dma_addr, + GFP_KERNEL); + if (stdev->dma_mrpc == NULL) + return -ENOMEM; + return 0; } @@ -1293,6 +1411,9 @@ static int switchtec_pci_probe(struct pci_dev *pdev, &stdev->mmio_part_cfg->mrpc_comp_hdr); enable_link_state_events(stdev); + if (stdev->dma_mrpc) + enable_dma_mrpc(stdev); + rc = cdev_device_add(&stdev->cdev, &stdev->dev); if (rc) goto err_devadd; @@ -1318,7 +1439,6 @@ static void switchtec_pci_remove(struct pci_dev *pdev) cdev_device_del(&stdev->cdev, &stdev->dev); ida_simple_remove(&switchtec_minor_ida, MINOR(stdev->dev.devt)); dev_info(&stdev->dev, "unregistered.\n"); - stdev_kill(stdev); put_device(&stdev->dev); } diff --git a/drivers/usb/dwc3/dwc3-haps.c b/drivers/usb/dwc3/dwc3-haps.c index c9cc33881bef..02d57d98ef9b 100644 --- a/drivers/usb/dwc3/dwc3-haps.c +++ b/drivers/usb/dwc3/dwc3-haps.c @@ -15,10 +15,6 @@ #include <linux/platform_device.h> #include <linux/property.h> -#define PCI_DEVICE_ID_SYNOPSYS_HAPSUSB3 0xabcd -#define PCI_DEVICE_ID_SYNOPSYS_HAPSUSB3_AXI 0xabce -#define PCI_DEVICE_ID_SYNOPSYS_HAPSUSB31 0xabcf - /** * struct dwc3_haps - Driver private structure * @dwc3: child dwc3 platform_device diff --git a/include/linux/mfd/syscon/imx6q-iomuxc-gpr.h b/include/linux/mfd/syscon/imx6q-iomuxc-gpr.h index 6c1ad160ed87..c1b25f5e386d 100644 --- a/include/linux/mfd/syscon/imx6q-iomuxc-gpr.h +++ b/include/linux/mfd/syscon/imx6q-iomuxc-gpr.h @@ -440,6 +440,7 @@ #define IMX6SX_GPR5_DISP_MUX_DCIC1_MASK (0x1 << 1) #define IMX6SX_GPR12_PCIE_TEST_POWERDOWN BIT(30) +#define IMX6SX_GPR12_PCIE_PM_TURN_OFF BIT(16) #define IMX6SX_GPR12_PCIE_RX_EQ_MASK (0x7 << 0) #define IMX6SX_GPR12_PCIE_RX_EQ_2 (0x2 << 0) diff --git a/include/linux/pci.h b/include/linux/pci.h index 11c71c4ecf75..8e3c646bc15c 100644 --- a/include/linux/pci.h +++ b/include/linux/pci.h @@ -405,6 +405,7 @@ struct pci_dev { unsigned int non_compliant_bars:1; /* Broken BARs; ignore them */ unsigned int is_probed:1; /* Device probing in progress */ unsigned int link_active_reporting:1;/* Device capable of reporting link active */ + unsigned int no_vf_scan:1; /* Don't scan for VFs after IOV enablement */ pci_dev_flags_t dev_flags; atomic_t enable_cnt; /* pci_enable_device has been called */ @@ -764,9 +765,9 @@ struct pci_driver { int (*suspend)(struct pci_dev *dev, pm_message_t state); /* Device suspended */ int (*suspend_late)(struct pci_dev *dev, pm_message_t state); int (*resume_early)(struct pci_dev *dev); - int (*resume) (struct pci_dev *dev); /* Device woken up */ - void (*shutdown) (struct pci_dev *dev); - int (*sriov_configure) (struct pci_dev *dev, int num_vfs); /* On PF */ + int (*resume)(struct pci_dev *dev); /* Device woken up */ + void (*shutdown)(struct pci_dev *dev); + int (*sriov_configure)(struct pci_dev *dev, int num_vfs); /* On PF */ const struct pci_error_handlers *err_handler; const struct attribute_group **groups; struct device_driver driver; diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h index 69f0abe1ba1a..25db0c1586ea 100644 --- a/include/linux/pci_ids.h +++ b/include/linux/pci_ids.h @@ -2358,6 +2358,9 @@ #define PCI_DEVICE_ID_CENATEK_IDE 0x0001 #define PCI_VENDOR_ID_SYNOPSYS 0x16c3 +#define PCI_DEVICE_ID_SYNOPSYS_HAPSUSB3 0xabcd +#define PCI_DEVICE_ID_SYNOPSYS_HAPSUSB3_AXI 0xabce +#define PCI_DEVICE_ID_SYNOPSYS_HAPSUSB31 0xabcf #define PCI_VENDOR_ID_VITESSE 0x1725 #define PCI_DEVICE_ID_VITESSE_VSC7174 0x7174 diff --git a/include/linux/switchtec.h b/include/linux/switchtec.h index ab400af6f0ce..eee0412bdf4b 100644 --- a/include/linux/switchtec.h +++ b/include/linux/switchtec.h @@ -29,6 +29,7 @@ #define SWITCHTEC_EVENT_EN_IRQ BIT(3) #define SWITCHTEC_EVENT_FATAL BIT(4) +#define SWITCHTEC_DMA_MRPC_EN BIT(0) enum { SWITCHTEC_GAS_MRPC_OFFSET = 0x0000, SWITCHTEC_GAS_TOP_CFG_OFFSET = 0x1000, @@ -46,6 +47,10 @@ struct mrpc_regs { u32 cmd; u32 status; u32 ret_value; + u32 dma_en; + u64 dma_addr; + u32 dma_vector; + u32 dma_ver; } __packed; enum mrpc_status { @@ -342,6 +347,14 @@ struct pff_csr_regs { struct switchtec_ntb; +struct dma_mrpc_output { + u32 status; + u32 cmd_id; + u32 rtn_code; + u32 output_size; + u8 data[SWITCHTEC_MRPC_PAYLOAD_SIZE]; +}; + struct switchtec_dev { struct pci_dev *pdev; struct device dev; @@ -381,6 +394,9 @@ struct switchtec_dev { u8 link_event_count[SWITCHTEC_MAX_PFF_CSR]; struct switchtec_ntb *sndev; + + struct dma_mrpc_output *dma_mrpc; + dma_addr_t dma_mrpc_dma_addr; }; static inline struct switchtec_dev *to_stdev(struct device *dev) |