diff options
Diffstat (limited to 'Documentation/admin-guide/kernel-parameters.txt')
| -rw-r--r-- | Documentation/admin-guide/kernel-parameters.txt | 76 |
1 files changed, 66 insertions, 10 deletions
diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt index ade4e6ec23e0..dbc22d684627 100644 --- a/Documentation/admin-guide/kernel-parameters.txt +++ b/Documentation/admin-guide/kernel-parameters.txt @@ -437,6 +437,12 @@ no delay (0). Format: integer + bootconfig [KNL] + Extended command line options can be added to an initrd + and this will cause the kernel to look for it. + + See Documentation/admin-guide/bootconfig.rst + bert_disable [ACPI] Disable BERT OS support on buggy BIOSes. @@ -511,7 +517,7 @@ 1 -- check protection requested by application. Default value is set via a kernel config option. Value can be changed at runtime via - /selinux/checkreqprot. + /sys/fs/selinux/checkreqprot. cio_ignore= [S390] See Documentation/s390/common_io.rst for details. @@ -834,6 +840,18 @@ dump out devices still on the deferred probe list after retrying. + dfltcc= [HW,S390] + Format: { on | off | def_only | inf_only | always } + on: s390 zlib hardware support for compression on + level 1 and decompression (default) + off: No s390 zlib hardware support + def_only: s390 zlib hardware support for deflate + only (compression on level 1) + inf_only: s390 zlib hardware support for inflate + only (decompression) + always: Same as 'on' but ignores the selected compression + level always using hardware support (used for debugging) + dhash_entries= [KNL] Set number of hash buckets for dentry cache. @@ -1165,10 +1183,10 @@ efi= [EFI] Format: { "old_map", "nochunk", "noruntime", "debug", - "nosoftreserve" } + "nosoftreserve", "disable_early_pci_dma", + "no_disable_early_pci_dma" } old_map [X86-64]: switch to the old ioremap-based EFI - runtime services mapping. 32-bit still uses this one by - default. + runtime services mapping. [Needs CONFIG_X86_UV=y] nochunk: disable reading files in "chunks" in the EFI boot stub, as chunking can cause problems with some firmware implementations. @@ -1180,6 +1198,10 @@ claim. Specify efi=nosoftreserve to disable this reservation and treat the memory by its base type (i.e. EFI_CONVENTIONAL_MEMORY / "System RAM"). + disable_early_pci_dma: Disable the busmaster bit on all + PCI bridges while in the EFI boot stub + no_disable_early_pci_dma: Leave the busmaster bit set + on all PCI bridges while in the EFI boot stub efi_no_storage_paranoia [EFI; X86] Using this parameter you can use more than 50% of @@ -1245,7 +1267,8 @@ 0 -- permissive (log only, no denials). 1 -- enforcing (deny and log). Default value is 0. - Value can be changed at runtime via /selinux/enforce. + Value can be changed at runtime via + /sys/fs/selinux/enforce. erst_disable [ACPI] Disable Error Record Serialization Table (ERST) @@ -1933,9 +1956,31 @@ <cpu number> begins at 0 and the maximum value is "number of CPUs in system - 1". - The format of <cpu-list> is described above. - + managed_irq + + Isolate from being targeted by managed interrupts + which have an interrupt mask containing isolated + CPUs. The affinity of managed interrupts is + handled by the kernel and cannot be changed via + the /proc/irq/* interfaces. + + This isolation is best effort and only effective + if the automatically assigned interrupt mask of a + device queue contains isolated and housekeeping + CPUs. If housekeeping CPUs are online then such + interrupts are directed to the housekeeping CPU + so that IO submitted on the housekeeping CPU + cannot disturb the isolated CPU. + + If a queue's affinity mask contains only isolated + CPUs then this parameter has no effect on the + interrupt routing decision, though interrupts are + only delivered when tasks running on those + isolated CPUs submit IO. IO submitted on + housekeeping CPUs has no influence on those + queues. + The format of <cpu-list> is described above. iucv= [HW,NET] @@ -3978,6 +4023,19 @@ test until boot completes in order to avoid interference. + rcuperf.kfree_rcu_test= [KNL] + Set to measure performance of kfree_rcu() flooding. + + rcuperf.kfree_nthreads= [KNL] + The number of threads running loops of kfree_rcu(). + + rcuperf.kfree_alloc_num= [KNL] + Number of allocations and frees done in an iteration. + + rcuperf.kfree_loops= [KNL] + Number of loops doing rcuperf.kfree_alloc_num number + of allocations and frees. + rcuperf.nreaders= [KNL] Set number of RCU readers. The value -1 selects N, where N is the number of CPUs. A value @@ -4348,9 +4406,7 @@ See security/selinux/Kconfig help text. 0 -- disable. 1 -- enable. - Default value is set via kernel config option. - If enabled at boot time, /selinux/disable can be used - later to disable prior to initial policy load. + Default value is 1. apparmor= [APPARMOR] Disable or enable AppArmor at boot time Format: { "0" | "1" } |