diff options
Diffstat (limited to 'Documentation/devicetree/bindings/clock')
5 files changed, 286 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt index e71c675ba5da..904ae682ea90 100644 --- a/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt @@ -32,6 +32,7 @@ clock-output-names: - "clkin_i2s" - external I2S clock - optional, - "gmac_clkin" - external GMAC clock - optional - "phy_50m_out" - output clock of the pll in the mac phy + - "hdmi_phy" - output clock of the hdmi phy pll - optional Example: Clock controller node: diff --git a/Documentation/devicetree/bindings/clock/silabs,si544.txt b/Documentation/devicetree/bindings/clock/silabs,si544.txt new file mode 100644 index 000000000000..b86535b80920 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/silabs,si544.txt @@ -0,0 +1,25 @@ +Binding for Silicon Labs 544 programmable I2C clock generator. + +Reference +This binding uses the common clock binding[1]. Details about the device can be +found in the datasheet[2]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Si544 datasheet + https://www.silabs.com/documents/public/data-sheets/si544-datasheet.pdf + +Required properties: + - compatible: One of "silabs,si514a", "silabs,si514b" "silabs,si514c" according + to the speed grade of the chip. + - reg: I2C device address. + - #clock-cells: From common clock bindings: Shall be 0. + +Optional properties: + - clock-output-names: From common clock bindings. Recommended to be "si544". + +Example: + si544: clock-controller@55 { + reg = <0x55>; + #clock-cells = <0>; + compatible = "silabs,si544b"; + }; diff --git a/Documentation/devicetree/bindings/clock/ti/davinci/da8xx-cfgchip.txt b/Documentation/devicetree/bindings/clock/ti/davinci/da8xx-cfgchip.txt new file mode 100644 index 000000000000..1e03dce99a8f --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/davinci/da8xx-cfgchip.txt @@ -0,0 +1,93 @@ +Binding for TI DA8XX/OMAP-L13X/AM17XX/AM18XX CFGCHIP clocks + +TI DA8XX/OMAP-L13X/AM17XX/AM18XX SoCs contain a general purpose set of +registers call CFGCHIPn. Some of these registers function as clock +gates. This document describes the bindings for those clocks. + +All of the clock nodes described below must be child nodes of a CFGCHIP node +(compatible = "ti,da830-cfgchip"). + +USB PHY clocks +-------------- +Required properties: +- compatible: shall be "ti,da830-usb-phy-clocks". +- #clock-cells: from common clock binding; shall be set to 1. +- clocks: phandles to the parent clocks corresponding to clock-names +- clock-names: shall be "fck", "usb_refclkin", "auxclk" + +This node provides two clocks. The clock at index 0 is the USB 2.0 PHY 48MHz +clock and the clock at index 1 is the USB 1.1 PHY 48MHz clock. + +eHRPWM Time Base Clock (TBCLK) +------------------------------ +Required properties: +- compatible: shall be "ti,da830-tbclksync". +- #clock-cells: from common clock binding; shall be set to 0. +- clocks: phandle to the parent clock +- clock-names: shall be "fck" + +PLL DIV4.5 divider +------------------ +Required properties: +- compatible: shall be "ti,da830-div4p5ena". +- #clock-cells: from common clock binding; shall be set to 0. +- clocks: phandle to the parent clock +- clock-names: shall be "pll0_pllout" + +EMIFA clock source (ASYNC1) +--------------------------- +Required properties: +- compatible: shall be "ti,da850-async1-clksrc". +- #clock-cells: from common clock binding; shall be set to 0. +- clocks: phandles to the parent clocks corresponding to clock-names +- clock-names: shall be "pll0_sysclk3", "div4.5" + +ASYNC3 clock source +------------------- +Required properties: +- compatible: shall be "ti,da850-async3-clksrc". +- #clock-cells: from common clock binding; shall be set to 0. +- clocks: phandles to the parent clocks corresponding to clock-names +- clock-names: shall be "pll0_sysclk2", "pll1_sysclk2" + +Examples: + + cfgchip: syscon@1417c { + compatible = "ti,da830-cfgchip", "syscon", "simple-mfd"; + reg = <0x1417c 0x14>; + + usb_phy_clk: usb-phy-clocks { + compatible = "ti,da830-usb-phy-clocks"; + #clock-cells = <1>; + clocks = <&psc1 1>, <&usb_refclkin>, <&pll0_auxclk>; + clock-names = "fck", "usb_refclkin", "auxclk"; + }; + ehrpwm_tbclk: ehrpwm_tbclk { + compatible = "ti,da830-tbclksync"; + #clock-cells = <0>; + clocks = <&psc1 17>; + clock-names = "fck"; + }; + div4p5_clk: div4.5 { + compatible = "ti,da830-div4p5ena"; + #clock-cells = <0>; + clocks = <&pll0_pllout>; + clock-names = "pll0_pllout"; + }; + async1_clk: async1 { + compatible = "ti,da850-async1-clksrc"; + #clock-cells = <0>; + clocks = <&pll0_sysclk 3>, <&div4p5_clk>; + clock-names = "pll0_sysclk3", "div4.5"; + }; + async3_clk: async3 { + compatible = "ti,da850-async3-clksrc"; + #clock-cells = <0>; + clocks = <&pll0_sysclk 2>, <&pll1_sysclk 2>; + clock-names = "pll0_sysclk2", "pll1_sysclk2"; + }; + }; + +Also see: +- Documentation/devicetree/bindings/clock/clock-bindings.txt + diff --git a/Documentation/devicetree/bindings/clock/ti/davinci/pll.txt b/Documentation/devicetree/bindings/clock/ti/davinci/pll.txt new file mode 100644 index 000000000000..36998e184821 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/davinci/pll.txt @@ -0,0 +1,96 @@ +Binding for TI DaVinci PLL Controllers + +The PLL provides clocks to most of the components on the SoC. In addition +to the PLL itself, this controller also contains bypasses, gates, dividers, +an multiplexers for various clock signals. + +Required properties: +- compatible: shall be one of: + - "ti,da850-pll0" for PLL0 on DA850/OMAP-L138/AM18XX + - "ti,da850-pll1" for PLL1 on DA850/OMAP-L138/AM18XX +- reg: physical base address and size of the controller's register area. +- clocks: phandles corresponding to the clock names +- clock-names: names of the clock sources - depends on compatible string + - for "ti,da850-pll0", shall be "clksrc", "extclksrc" + - for "ti,da850-pll1", shall be "clksrc" + +Optional properties: +- ti,clkmode-square-wave: Indicates that the the board is supplying a square + wave input on the OSCIN pin instead of using a crystal oscillator. + This property is only valid when compatible = "ti,da850-pll0". + + +Optional child nodes: + +pllout + Describes the main PLL clock output (before POSTDIV). The node name must + be "pllout". + + Required properties: + - #clock-cells: shall be 0 + +sysclk + Describes the PLLDIVn divider clocks that provide the SYSCLKn clock + domains. The node name must be "sysclk". Consumers of this node should + use "n" in "SYSCLKn" as the index parameter for the clock cell. + + Required properties: + - #clock-cells: shall be 1 + +auxclk + Describes the AUXCLK output of the PLL. The node name must be "auxclk". + This child node is only valid when compatible = "ti,da850-pll0". + + Required properties: + - #clock-cells: shall be 0 + +obsclk + Describes the OBSCLK output of the PLL. The node name must be "obsclk". + + Required properties: + - #clock-cells: shall be 0 + + +Examples: + + pll0: clock-controller@11000 { + compatible = "ti,da850-pll0"; + reg = <0x11000 0x1000>; + clocks = <&ref_clk>, <&pll1_sysclk 3>; + clock-names = "clksrc", "extclksrc"; + ti,clkmode-square-wave; + + pll0_pllout: pllout { + #clock-cells = <0>; + }; + + pll0_sysclk: sysclk { + #clock-cells = <1>; + }; + + pll0_auxclk: auxclk { + #clock-cells = <0>; + }; + + pll0_obsclk: obsclk { + #clock-cells = <0>; + }; + }; + + pll1: clock-controller@21a000 { + compatible = "ti,da850-pll1"; + reg = <0x21a000 0x1000>; + clocks = <&ref_clk>; + clock-names = "clksrc"; + + pll0_sysclk: sysclk { + #clock-cells = <1>; + }; + + pll0_obsclk: obsclk { + #clock-cells = <0>; + }; + }; + +Also see: +- Documentation/devicetree/bindings/clock/clock-bindings.txt diff --git a/Documentation/devicetree/bindings/clock/ti/davinci/psc.txt b/Documentation/devicetree/bindings/clock/ti/davinci/psc.txt new file mode 100644 index 000000000000..dae4ad8e198c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/davinci/psc.txt @@ -0,0 +1,71 @@ +Binding for TI DaVinci Power Sleep Controller (PSC) + +The PSC provides power management, clock gating and reset functionality. It is +primarily used for clocking. + +Required properties: +- compatible: shall be one of: + - "ti,da850-psc0" for PSC0 on DA850/OMAP-L138/AM18XX + - "ti,da850-psc1" for PSC1 on DA850/OMAP-L138/AM18XX +- reg: physical base address and size of the controller's register area +- #clock-cells: from common clock binding; shall be set to 1 +- #power-domain-cells: from generic power domain binding; shall be set to 1. +- clocks: phandles to clocks corresponding to the clock-names property +- clock-names: list of parent clock names - depends on compatible value + - for "ti,da850-psc0", shall be "pll0_sysclk1", "pll0_sysclk2", + "pll0_sysclk4", "pll0_sysclk6", "async1" + - for "ti,da850-psc1", shall be "pll0_sysclk2", "pll0_sysclk4", "async3" + +Optional properties: +- #reset-cells: from reset binding; shall be set to 1 - only applicable when + at least one local domain provides a local reset. + +Consumers: + + Clock, power domain and reset consumers shall use the local power domain + module ID (LPSC) as the index corresponding to the clock cell. Refer to + the device-specific datasheet to find these numbers. NB: Most local + domains only provide a clock/power domain and not a reset. + +Examples: + + psc0: clock-controller@10000 { + compatible = "ti,da850-psc0"; + reg = <0x10000 0x1000>; + #clock-cells = <1>; + #power-domain-cells = <1>; + #reset-cells = <1>; + clocks = <&pll0_sysclk 1>, <&pll0_sysclk 2>, + <&pll0_sysclk 4>, <&pll0_sysclk 6>, <&async1_clk>; + clock_names = "pll0_sysclk1", "pll0_sysclk2", + "pll0_sysclk4", "pll0_sysclk6", "async1"; + }; + psc1: clock-controller@227000 { + compatible = "ti,da850-psc1"; + reg = <0x227000 0x1000>; + #clock-cells = <1>; + #power-domain-cells = <1>; + clocks = <&pll0_sysclk 2>, <&pll0_sysclk 4>, <&async3_clk>; + clock_names = "pll0_sysclk2", "pll0_sysclk4", "async3"; + }; + + /* consumer */ + dsp: dsp@11800000 { + compatible = "ti,da850-dsp"; + reg = <0x11800000 0x40000>, + <0x11e00000 0x8000>, + <0x11f00000 0x8000>, + <0x01c14044 0x4>, + <0x01c14174 0x8>; + reg-names = "l2sram", "l1pram", "l1dram", "host1cfg", "chipsig"; + interrupt-parent = <&intc>; + interrupts = <28>; + clocks = <&psc0 15>; + power-domains = <&psc0 15>; + resets = <&psc0 15>; + }; + +Also see: +- Documentation/devicetree/bindings/clock/clock-bindings.txt +- Documentation/devicetree/bindings/power/power_domain.txt +- Documentation/devicetree/bindings/reset/reset.txt |