diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mmc')
6 files changed, 38 insertions, 8 deletions
diff --git a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt index 64bcb8be973c..0d93b4b0e0e3 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt @@ -11,9 +11,11 @@ Required properties: - interrupt-parent : interrupt source phandle. - clock-frequency : specifies eSDHC base clock frequency. - sdhci,wp-inverted : (optional) specifies that eSDHC controller - reports inverted write-protect state; + reports inverted write-protect state; New devices should use + the generic "wp-inverted" property. - sdhci,1-bit-only : (optional) specifies that a controller can - only handle 1-bit data transfers. + only handle 1-bit data transfers. New devices should use the + generic "bus-width = <1>" property. - sdhci,auto-cmd12: (optional) specifies that a controller can only handle auto CMD12. diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt index ab22fe6e73ab..c7e404b3ef05 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt @@ -9,7 +9,7 @@ Required properties: - interrupts : Should contain eSDHC interrupt Optional properties: -- fsl,card-wired : Indicate the card is wired to host permanently +- non-removable : Indicate the card is wired to host permanently - fsl,cd-internal : Indicate to use controller internal card detection - fsl,wp-internal : Indicate to use controller internal write protection - cd-gpios : Specify GPIOs for card detection diff --git a/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt index 89a0084df2f7..d64aea5a4203 100644 --- a/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt +++ b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt @@ -10,7 +10,8 @@ Required properties: Optional properties: - gpios : may specify GPIOs in this order: Card-Detect GPIO, - Write-Protect GPIO. + Write-Protect GPIO. Note that this does not follow the + binding from mmc.txt, for historic reasons. - interrupts : the interrupt of a card detect interrupt. - interrupt-parent : the phandle for the interrupt controller that services interrupts for this device. diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt new file mode 100644 index 000000000000..6e70dcde0a71 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -0,0 +1,27 @@ +These properties are common to multiple MMC host controllers. Any host +that requires the respective functionality should implement them using +these definitions. + +Required properties: +- bus-width: Number of data lines, can be <1>, <4>, or <8> + +Optional properties: +- cd-gpios : Specify GPIOs for card detection, see gpio binding +- wp-gpios : Specify GPIOs for write protection, see gpio binding +- cd-inverted: when present, polarity on the wp gpio line is inverted +- wp-inverted: when present, polarity on the wp gpio line is inverted +- non-removable: non-removable slot (like eMMC) +- max-frequency: maximum operating clock frequency + +Example: + +sdhci@ab000000 { + compatible = "sdhci"; + reg = <0xab000000 0x200>; + interrupts = <23>; + bus-width = <4>; + cd-gpios = <&gpio 69 0>; + cd-inverted; + wp-gpios = <&gpio 70 0>; + max-frequency = <50000000>; +} diff --git a/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt b/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt index 7e51154679a6..f77c3031607f 100644 --- a/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt @@ -7,12 +7,12 @@ Required properties: - compatible : Should be "nvidia,<chip>-sdhci" - reg : Should contain SD/MMC registers location and length - interrupts : Should contain SD/MMC interrupt +- bus-width : Number of data lines, can be <1>, <4>, or <8> Optional properties: - cd-gpios : Specify GPIOs for card detection - wp-gpios : Specify GPIOs for write protection - power-gpios : Specify GPIOs for power control -- support-8bit : Boolean, indicates if 8-bit mode should be used. Example: @@ -23,5 +23,5 @@ sdhci@c8000200 { cd-gpios = <&gpio 69 0>; /* gpio PI5 */ wp-gpios = <&gpio 57 0>; /* gpio PH1 */ power-gpios = <&gpio 155 0>; /* gpio PT3 */ - support-8bit; + bus-width = <8>; }; diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt index dbd4368ab8cc..8a53958c9a9f 100644 --- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt +++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt @@ -15,7 +15,7 @@ Optional properties: ti,dual-volt: boolean, supports dual voltage cards <supply-name>-supply: phandle to the regulator device tree node "supply-name" examples are "vmmc", "vmmc_aux" etc -ti,bus-width: Number of data lines, default assumed is 1 if the property is missing. +bus-width: Number of data lines, default assumed is 1 if the property is missing. cd-gpios: GPIOs for card detection wp-gpios: GPIOs for write protection ti,non-removable: non-removable slot (like eMMC) @@ -27,7 +27,7 @@ Example: reg = <0x4809c000 0x400>; ti,hwmods = "mmc1"; ti,dual-volt; - ti,bus-width = <4>; + bus-width = <4>; vmmc-supply = <&vmmc>; /* phandle to regulator node */ ti,non-removable; }; |