diff options
Diffstat (limited to 'Documentation/devicetree/bindings/usb')
20 files changed, 532 insertions, 133 deletions
diff --git a/Documentation/devicetree/bindings/usb/dwc2.yaml b/Documentation/devicetree/bindings/usb/dwc2.yaml index 481aaa09f3f2..4cebce682d16 100644 --- a/Documentation/devicetree/bindings/usb/dwc2.yaml +++ b/Documentation/devicetree/bindings/usb/dwc2.yaml @@ -41,6 +41,7 @@ properties: - amlogic,meson8b-usb - amlogic,meson-gxbb-usb - amlogic,meson-g12a-usb + - intel,socfpga-agilex-hsotg - const: snps,dwc2 - const: amcc,dwc-otg - const: apm,apm82181-dwc-otg @@ -68,6 +69,13 @@ properties: items: - const: otg + disable-over-current: + type: boolean + description: whether to disable detection of over-current condition. + + iommus: + maxItems: 1 + resets: items: - description: common reset diff --git a/Documentation/devicetree/bindings/usb/dwc3-cavium.txt b/Documentation/devicetree/bindings/usb/dwc3-cavium.txt index 710b782ccf65..171df79360ff 100644 --- a/Documentation/devicetree/bindings/usb/dwc3-cavium.txt +++ b/Documentation/devicetree/bindings/usb/dwc3-cavium.txt @@ -20,7 +20,7 @@ Example device node: refclk-type-hs = "dlmc_ref_clk0"; power = <0x00000002 0x00000002 0x00000001>; xhci@1690000000000 { - compatible = "cavium,octeon-7130-xhci", "synopsys,dwc3"; + compatible = "cavium,octeon-7130-xhci", "snps,dwc3"; reg = <0x00016900 0x00000000 0x00000010 0x00000000>; interrupt-parent = <0x00000010>; interrupts = <0x00000009 0x00000004>; diff --git a/Documentation/devicetree/bindings/usb/exynos-usb.txt b/Documentation/devicetree/bindings/usb/exynos-usb.txt deleted file mode 100644 index f7ae79825d7d..000000000000 --- a/Documentation/devicetree/bindings/usb/exynos-usb.txt +++ /dev/null @@ -1,115 +0,0 @@ -Samsung Exynos SoC USB controller - -The USB devices interface with USB controllers on Exynos SOCs. -The device node has following properties. - -EHCI -Required properties: - - compatible: should be "samsung,exynos4210-ehci" for USB 2.0 - EHCI controller in host mode. - - reg: physical base address of the controller and length of memory mapped - region. - - interrupts: interrupt number to the cpu. - - clocks: from common clock binding: handle to usb clock. - - clock-names: from common clock binding: Shall be "usbhost". - - phys: from the *Generic PHY* bindings; array specifying phy(s) used - by the root port. - - phy-names: from the *Generic PHY* bindings; array of the names for - each phy for the root ports, must be a subset of the following: - "host", "hsic0", "hsic1". - -Optional properties: - - samsung,vbus-gpio: if present, specifies the GPIO that - needs to be pulled up for the bus to be powered. - -Example: - - usb@12110000 { - compatible = "samsung,exynos4210-ehci"; - reg = <0x12110000 0x100>; - interrupts = <0 71 0>; - samsung,vbus-gpio = <&gpx2 6 1 3 3>; - - clocks = <&clock 285>; - clock-names = "usbhost"; - - phys = <&usb2phy 1>; - phy-names = "host"; - }; - -OHCI -Required properties: - - compatible: should be "samsung,exynos4210-ohci" for USB 2.0 - OHCI companion controller in host mode. - - reg: physical base address of the controller and length of memory mapped - region. - - interrupts: interrupt number to the cpu. - - clocks: from common clock binding: handle to usb clock. - - clock-names: from common clock binding: Shall be "usbhost". - - phys: from the *Generic PHY* bindings; array specifying phy(s) used - by the root port. - - phy-names: from the *Generic PHY* bindings; array of the names for - each phy for the root ports, must be a subset of the following: - "host", "hsic0", "hsic1". - -Example: - usb@12120000 { - compatible = "samsung,exynos4210-ohci"; - reg = <0x12120000 0x100>; - interrupts = <0 71 0>; - - clocks = <&clock 285>; - clock-names = "usbhost"; - - phys = <&usb2phy 1>; - phy-names = "host"; - }; - -DWC3 -Required properties: - - compatible: should be one of the following - - "samsung,exynos5250-dwusb3": for USB 3.0 DWC3 controller on - Exynos5250/5420. - "samsung,exynos5433-dwusb3": for USB 3.0 DWC3 controller on - Exynos5433. - "samsung,exynos7-dwusb3": for USB 3.0 DWC3 controller on Exynos7. - - #address-cells, #size-cells : should be '1' if the device has sub-nodes - with 'reg' property. - - ranges: allows valid 1:1 translation between child's address space and - parent's address space - - clocks: Clock IDs array as required by the controller. - - clock-names: Names of clocks corresponding to IDs in the clock property. - Following clock names shall be provided for different - compatibles: - - samsung,exynos5250-dwusb3: "usbdrd30", - - samsung,exynos5433-dwusb3: "aclk", "susp_clk", "pipe_pclk", - "phyclk", - - samsung,exynos7-dwusb3: "usbdrd30", "usbdrd30_susp_clk", - "usbdrd30_axius_clk" - - vdd10-supply: 1.0V powr supply - - vdd33-supply: 3.0V/3.3V power supply - -Sub-nodes: -The dwc3 core should be added as subnode to Exynos dwc3 glue. -- dwc3 : - The binding details of dwc3 can be found in: - Documentation/devicetree/bindings/usb/snps,dwc3.yaml - -Example: - usb@12000000 { - compatible = "samsung,exynos5250-dwusb3"; - clocks = <&clock 286>; - clock-names = "usbdrd30"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - vdd10-supply = <&ldo11_reg>; - vdd33-supply = <&ldo9_reg>; - - dwc3 { - compatible = "synopsys,dwc3"; - reg = <0x12000000 0x10000>; - interrupts = <0 72 0>; - usb-phy = <&usb2_phy &usb3_phy>; - }; - }; diff --git a/Documentation/devicetree/bindings/usb/fsl,imx8mp-dwc3.yaml b/Documentation/devicetree/bindings/usb/fsl,imx8mp-dwc3.yaml index 974032b1fda0..01ab0f922ae8 100644 --- a/Documentation/devicetree/bindings/usb/fsl,imx8mp-dwc3.yaml +++ b/Documentation/devicetree/bindings/usb/fsl,imx8mp-dwc3.yaml @@ -15,9 +15,9 @@ properties: const: fsl,imx8mp-dwc3 reg: - maxItems: 1 - description: Address and length of the register set for the wrapper of - dwc3 core on the SOC. + items: + - description: Address and length of the register set for HSIO Block Control + - description: Address and length of the register set for the wrapper of dwc3 core on the SOC. "#address-cells": enum: [ 1, 2 ] @@ -49,6 +49,28 @@ properties: - const: hsio - const: suspend + fsl,permanently-attached: + type: boolean + description: + Indicates if the device atached to a downstream port is + permanently attached. + + fsl,disable-port-power-control: + type: boolean + description: + Indicates whether the host controller implementation includes port + power control. Defines Bit 3 in capability register (HCCPARAMS). + + fsl,over-current-active-low: + type: boolean + description: + Over current signal polarity is active low. + + fsl,power-active-low: + type: boolean + description: + Power pad (PWR) polarity is active low. + # Required child node: patternProperties: @@ -74,7 +96,8 @@ examples: #include <dt-bindings/interrupt-controller/arm-gic.h> usb3_0: usb@32f10100 { compatible = "fsl,imx8mp-dwc3"; - reg = <0x32f10100 0x8>; + reg = <0x32f10100 0x8>, + <0x381f0000 0x20>; clocks = <&clk IMX8MP_CLK_HSIO_ROOT>, <&clk IMX8MP_CLK_USB_ROOT>; clock-names = "hsio", "suspend"; diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml index 11f7bacd4e2b..084d7135b2d9 100644 --- a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml +++ b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml @@ -30,6 +30,7 @@ properties: - mediatek,mt7629-xhci - mediatek,mt8173-xhci - mediatek,mt8183-xhci + - mediatek,mt8186-xhci - mediatek,mt8192-xhci - mediatek,mt8195-xhci - const: mediatek,mtk-xhci @@ -146,7 +147,11 @@ properties: 2 - used by mt2712 etc, revision 2 following IPM rule; 101 - used by mt8183, specific 1.01; 102 - used by mt8192, specific 1.02; - enum: [1, 2, 101, 102] + 103 - used by mt8195, IP0, specific 1.03; + 104 - used by mt8195, IP1, specific 1.04; + 105 - used by mt8195, IP2, specific 1.05; + 106 - used by mt8195, IP3, specific 1.06; + enum: [1, 2, 101, 102, 103, 104, 105, 106] mediatek,u3p-dis-msk: $ref: /schemas/types.yaml#/definitions/uint32 diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml index 77db1233516e..df766f8de872 100644 --- a/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml +++ b/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml @@ -132,7 +132,7 @@ properties: default: host connector: - $ref: /connector/usb-connector.yaml# + $ref: /schemas/connector/usb-connector.yaml# description: Connector for dual role switch, especially for "gpio-usb-b-connector" type: object @@ -191,7 +191,7 @@ properties: patternProperties: "^usb@[0-9a-f]+$": type: object - $ref: /usb/mediatek,mtk-xhci.yaml# + $ref: /schemas/usb/mediatek,mtk-xhci.yaml# description: The xhci should be added as subnode to mtu3 as shown in the following example if the host mode is enabled. diff --git a/Documentation/devicetree/bindings/usb/mediatek,musb.yaml b/Documentation/devicetree/bindings/usb/mediatek,musb.yaml index 03d62d60ce5f..11a33f9b1f17 100644 --- a/Documentation/devicetree/bindings/usb/mediatek,musb.yaml +++ b/Documentation/devicetree/bindings/usb/mediatek,musb.yaml @@ -63,7 +63,7 @@ properties: maxItems: 1 connector: - $ref: /connector/usb-connector.yaml# + $ref: /schemas/connector/usb-connector.yaml# description: Connector for dual role switch type: object diff --git a/Documentation/devicetree/bindings/usb/microchip,mpfs-musb.yaml b/Documentation/devicetree/bindings/usb/microchip,mpfs-musb.yaml new file mode 100644 index 000000000000..48c458c65848 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/microchip,mpfs-musb.yaml @@ -0,0 +1,59 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/usb/microchip,mpfs-musb.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip MPFS USB Controller Device Tree Bindings + +allOf: + - $ref: usb-drd.yaml# + +maintainers: + - Conor Dooley <conor.dooley@microchip.com> + +properties: + compatible: + enum: + - microchip,mpfs-musb + + dr_mode: true + + reg: + maxItems: 1 + + interrupts: + minItems: 2 + maxItems: 2 + + interrupt-names: + items: + - const: dma + - const: mc + + clocks: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - interrupt-names + - clocks + +additionalProperties: false + +examples: + - | + #include "dt-bindings/clock/microchip,mpfs-clock.h" + usb@20201000 { + compatible = "microchip,mpfs-musb"; + reg = <0x20201000 0x1000>; + clocks = <&clkcfg CLK_USB>; + interrupt-parent = <&plic>; + interrupts = <86>, <87>; + interrupt-names = "dma", "mc"; + dr_mode = "host"; + }; + +... diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra-xudc.yaml b/Documentation/devicetree/bindings/usb/nvidia,tegra-xudc.yaml index a39c76b89484..fd6e7c81426e 100644 --- a/Documentation/devicetree/bindings/usb/nvidia,tegra-xudc.yaml +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra-xudc.yaml @@ -83,7 +83,7 @@ properties: - const: ss nvidia,xusb-padctl: - $ref: /schemas/types.yaml#/definitions/phandle-array + $ref: /schemas/types.yaml#/definitions/phandle description: phandle to the XUSB pad controller that is used to configure the USB pads used by the XUDC controller. diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml b/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml index 2d23a4ff702f..ce252db2aab3 100644 --- a/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml +++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml @@ -16,6 +16,7 @@ properties: - qcom,ipq4019-dwc3 - qcom,ipq6018-dwc3 - qcom,ipq8064-dwc3 + - qcom,msm8953-dwc3 - qcom,msm8996-dwc3 - qcom,msm8998-dwc3 - qcom,sc7180-dwc3 diff --git a/Documentation/devicetree/bindings/usb/renesas,usbhs.yaml b/Documentation/devicetree/bindings/usb/renesas,usbhs.yaml index 012fe80a7611..0bb841b28003 100644 --- a/Documentation/devicetree/bindings/usb/renesas,usbhs.yaml +++ b/Documentation/devicetree/bindings/usb/renesas,usbhs.yaml @@ -20,6 +20,7 @@ properties: - enum: - renesas,usbhs-r7s9210 # RZ/A2 - renesas,usbhs-r9a07g044 # RZ/G2{L,LC} + - renesas,usbhs-r9a07g054 # RZ/V2L - const: renesas,rza2-usbhs - items: @@ -116,7 +117,9 @@ allOf: properties: compatible: contains: - const: renesas,usbhs-r9a07g044 + enum: + - renesas,usbhs-r9a07g044 + - renesas,usbhs-r9a07g054 then: properties: interrupts: diff --git a/Documentation/devicetree/bindings/usb/richtek,rt1719.yaml b/Documentation/devicetree/bindings/usb/richtek,rt1719.yaml new file mode 100644 index 000000000000..65a93f7738d5 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/richtek,rt1719.yaml @@ -0,0 +1,85 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/usb/richtek,rt1719.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Richtek RT1719 sink-only Type-C PD controller bindings + +maintainers: + - ChiYuan Huang <cy_huang@richtek.com> + +description: | + The RT1719 is a sink-only USB Type-C contoller that complies with the latest + USB Type-C and PD standards. It does the USB Type-C detection including attach + and orientation. It integrates the physical layer of the USB BMC power + delivery protocol to allow up to 100W of power. The BMC PD block enables full + support for alternative interfaces of the Type-C specification. + +properties: + compatible: + enum: + - richtek,rt1719 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + wakeup-source: + description: enable IRQ remote wakeup, see power/wakeup-source.txt + type: boolean + + connector: + type: object + $ref: ../connector/usb-connector.yaml# + description: + Properties for usb c connector. + +additionalProperties: false + +required: + - compatible + - reg + - connector + - interrupts + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + rt1719@43 { + compatible = "richtek,rt1719"; + reg = <0x43>; + interrupts-extended = <&gpio26 2 IRQ_TYPE_LEVEL_LOW>; + wakeup-source; + + connector { + compatible = "usb-c-connector"; + label = "USB-C"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + endpoint { + remote-endpoint = <&usb_hs>; + }; + }; + port@1 { + reg = <1>; + endpoint { + remote-endpoint = <&usb_ss>; + }; + }; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml b/Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml index 04077f2d7faf..b3798d94d2fd 100644 --- a/Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml +++ b/Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml @@ -30,6 +30,7 @@ select: enum: - rockchip,rk3328-dwc3 - rockchip,rk3399-dwc3 + - rockchip,rk3568-dwc3 required: - compatible @@ -39,6 +40,7 @@ properties: - enum: - rockchip,rk3328-dwc3 - rockchip,rk3399-dwc3 + - rockchip,rk3568-dwc3 - const: snps,dwc3 reg: diff --git a/Documentation/devicetree/bindings/usb/samsung,exynos-dwc3.yaml b/Documentation/devicetree/bindings/usb/samsung,exynos-dwc3.yaml new file mode 100644 index 000000000000..22b91a27d776 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/samsung,exynos-dwc3.yaml @@ -0,0 +1,129 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/usb/samsung,exynos-dwc3.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung Exynos SoC USB 3.0 DWC3 Controller + +maintainers: + - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> + +properties: + compatible: + enum: + - samsung,exynos5250-dwusb3 + - samsung,exynos5433-dwusb3 + - samsung,exynos7-dwusb3 + + '#address-cells': + const: 1 + + clocks: + minItems: 1 + maxItems: 4 + + clock-names: + minItems: 1 + maxItems: 4 + + ranges: true + + '#size-cells': + const: 1 + + vdd10-supply: + description: 1.0V power supply + + vdd33-supply: + description: 3.0V/3.3V power supply + +patternProperties: + "^usb@[0-9a-f]+$": + $ref: snps,dwc3.yaml# + description: Required child node + +required: + - compatible + - '#address-cells' + - clocks + - clock-names + - ranges + - '#size-cells' + - vdd10-supply + - vdd33-supply + +allOf: + - if: + properties: + compatible: + contains: + const: samsung,exynos5250-dwusb3 + then: + properties: + clocks: + minItems: 1 + maxItems: 1 + clock-names: + items: + - const: usbdrd30 + + - if: + properties: + compatible: + contains: + const: samsung,exynos54333-dwusb3 + then: + properties: + clocks: + minItems: 4 + maxItems: 4 + clock-names: + items: + - const: aclk + - const: susp_clk + - const: pipe_pclk + - const: phyclk + + - if: + properties: + compatible: + contains: + const: samsung,exynos7-dwusb3 + then: + properties: + clocks: + minItems: 3 + maxItems: 3 + clock-names: + items: + - const: usbdrd30 + - const: usbdrd30_susp_clk + - const: usbdrd30_axius_clk + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/exynos5420.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + usb { + compatible = "samsung,exynos5250-dwusb3"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + clocks = <&clock CLK_USBD300>; + clock-names = "usbdrd30"; + vdd33-supply = <&ldo9_reg>; + vdd10-supply = <&ldo11_reg>; + + usb@12000000 { + compatible = "snps,dwc3"; + reg = <0x12000000 0x10000>; + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; + phys = <&usbdrd_phy0 0>, <&usbdrd_phy0 1>; + phy-names = "usb2-phy", "usb3-phy"; + snps,dis_u3_susphy_quirk; + }; + }; diff --git a/Documentation/devicetree/bindings/usb/samsung,exynos-usb2.yaml b/Documentation/devicetree/bindings/usb/samsung,exynos-usb2.yaml new file mode 100644 index 000000000000..fbf07d6e707a --- /dev/null +++ b/Documentation/devicetree/bindings/usb/samsung,exynos-usb2.yaml @@ -0,0 +1,117 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/usb/samsung,exynos-usb2.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung Exynos SoC USB 2.0 EHCI/OHCI Controller + +maintainers: + - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> + +properties: + compatible: + enum: + - samsung,exynos4210-ehci + - samsung,exynos4210-ohci + + '#address-cells': + const: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: usbhost + + interrupts: + maxItems: 1 + + phys: + minItems: 1 + maxItems: 3 + + phy-names: + items: + enum: [host, hsic0, hsic1] + minItems: 1 + maxItems: 3 + + reg: + maxItems: 1 + + samsung,vbus-gpio: + description: + Only for controller in EHCI mode, if present, specifies the GPIO that + needs to be pulled up for the bus to be powered. + + '#size-cells': + const: 0 + +patternProperties: + "^.*@[0-9a-f]{1,2}$": + description: The hard wired USB devices + type: object + $ref: /usb/usb-device.yaml + +required: + - compatible + - clocks + - clock-names + - interrupts + - phys + - phy-names + +allOf: + - if: + properties: + compatible: + contains: + const: samsung,exynos4210-ohci + then: + properties: + samsung,vbus-gpio: false + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/exynos5420.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + usb@12110000 { + compatible = "samsung,exynos4210-ehci"; + reg = <0x12110000 0x100>; + interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clock CLK_USBH20>; + clock-names = "usbhost"; + phys = <&usb2_phy 0>; + phy-names = "host"; + + #address-cells = <1>; + #size-cells = <0>; + + hub@1 { + compatible = "usb0424,9514"; + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + usbether@1 { + compatible = "usb0424,ec00"; + reg = <1>; + local-mac-address = [00 00 00 00 00 00]; + }; + }; + }; + + usb@12120000 { + compatible = "samsung,exynos4210-ohci"; + reg = <0x12120000 0x100>; + interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clock CLK_USBH20>; + clock-names = "usbhost"; + phys = <&usb2_phy 0>; + phy-names = "host"; + }; diff --git a/Documentation/devicetree/bindings/usb/snps,dwc3.yaml b/Documentation/devicetree/bindings/usb/snps,dwc3.yaml index d29ffcd27472..f4471f8bdbef 100644 --- a/Documentation/devicetree/bindings/usb/snps,dwc3.yaml +++ b/Documentation/devicetree/bindings/usb/snps,dwc3.yaml @@ -263,8 +263,11 @@ properties: Value for REFCLKPER field of GUCTL register for reference clock period in nanoseconds, when the hardware set default does not match the actual clock. - minimum: 1 - maximum: 0x3ff + + This binding is deprecated. Instead, provide an appropriate reference clock. + minimum: 8 + maximum: 62 + deprecated: true snps,rx-thr-num-pkt-prd: description: @@ -332,6 +335,12 @@ properties: items: enum: [1, 4, 8, 16, 32, 64, 128, 256] + port: + $ref: /schemas/graph.yaml#/properties/port + description: + This port is used with the 'usb-role-switch' property to connect the + dwc3 to type C connector. + unevaluatedProperties: false required: diff --git a/Documentation/devicetree/bindings/usb/st,stusb160x.yaml b/Documentation/devicetree/bindings/usb/st,stusb160x.yaml index ead1571e0e43..b5a8c9814dd3 100644 --- a/Documentation/devicetree/bindings/usb/st,stusb160x.yaml +++ b/Documentation/devicetree/bindings/usb/st,stusb160x.yaml @@ -32,9 +32,7 @@ properties: connector: type: object - - allOf: - - $ref: ../connector/usb-connector.yaml + $ref: /schemas/connector/usb-connector.yaml# properties: compatible: diff --git a/Documentation/devicetree/bindings/usb/ti,keystone-dwc3.yaml b/Documentation/devicetree/bindings/usb/ti,keystone-dwc3.yaml index 4f7a212fddd3..c1f0194ad0d5 100644 --- a/Documentation/devicetree/bindings/usb/ti,keystone-dwc3.yaml +++ b/Documentation/devicetree/bindings/usb/ti,keystone-dwc3.yaml @@ -92,7 +92,7 @@ examples: ranges; usb@2690000 { - compatible = "synopsys,dwc3"; + compatible = "snps,dwc3"; reg = <0x2690000 0x70000>; interrupts = <GIC_SPI 393 IRQ_TYPE_EDGE_RISING>; usb-phy = <&usb_phy>, <&usb_phy>; diff --git a/Documentation/devicetree/bindings/usb/usb-hcd.yaml b/Documentation/devicetree/bindings/usb/usb-hcd.yaml index 56853c17af66..1dc3d5d7b44f 100644 --- a/Documentation/devicetree/bindings/usb/usb-hcd.yaml +++ b/Documentation/devicetree/bindings/usb/usb-hcd.yaml @@ -33,7 +33,7 @@ patternProperties: "^.*@[0-9a-f]{1,2}$": description: The hard wired USB devices type: object - $ref: /usb/usb-device.yaml + $ref: /schemas/usb/usb-device.yaml additionalProperties: true diff --git a/Documentation/devicetree/bindings/usb/willsemi,wusb3801.yaml b/Documentation/devicetree/bindings/usb/willsemi,wusb3801.yaml new file mode 100644 index 000000000000..c2b2243c7892 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/willsemi,wusb3801.yaml @@ -0,0 +1,75 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/usb/willsemi,wusb3801.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: WUSB3801 Type-C port controller DT bindings + +description: + The Will Semiconductor WUSB3801 is a USB Type-C port controller which + supports role and plug orientation detection using the CC pins. It is + compatible with the USB Type-C Cable and Connector Specification v1.2. + +maintainers: + - Samuel Holland <samuel@sholland.org> + +properties: + compatible: + enum: + - willsemi,wusb3801 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + connector: + type: object + $ref: ../connector/usb-connector.yaml# + description: + The managed USB Type-C connector. Since WUSB3801 does not support + Power Delivery, the node should have the "pd-disable" property. + + properties: + compatible: + const: usb-c-connector + + required: + - pd-disable + +required: + - compatible + - reg + - interrupts + - connector + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + tcpc@60 { + compatible = "willsemi,wusb3801"; + reg = <0x60>; + interrupt-parent = <&gpio0>; + interrupts = <4 IRQ_TYPE_LEVEL_LOW>; + + connector { + compatible = "usb-c-connector"; + label = "USB-C"; + vbus-supply = <&otg_switch>; + power-role = "dual"; + try-power-role = "sink"; + data-role = "dual"; + typec-power-opmode = "default"; + pd-disable; + }; + }; + }; |