diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
6 files changed, 376 insertions, 145 deletions
diff --git a/Documentation/devicetree/bindings/mtd/nand-controller.yaml b/Documentation/devicetree/bindings/mtd/nand-controller.yaml index d0e422f4b3e0..678b39952502 100644 --- a/Documentation/devicetree/bindings/mtd/nand-controller.yaml +++ b/Documentation/devicetree/bindings/mtd/nand-controller.yaml @@ -143,6 +143,13 @@ patternProperties: Ready/Busy pins. Active state refers to the NAND ready state and should be set to GPIOD_ACTIVE_HIGH unless the signal is inverted. + secure-regions: + $ref: /schemas/types.yaml#/definitions/uint64-matrix + description: + Regions in the NAND chip which are protected using a secure element + like Trustzone. This property contains the start address and size of + the secure regions present. + required: - reg diff --git a/Documentation/devicetree/bindings/mtd/partitions/linksys,ns-partitions.yaml b/Documentation/devicetree/bindings/mtd/partitions/linksys,ns-partitions.yaml new file mode 100644 index 000000000000..99249cdfbfb3 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/partitions/linksys,ns-partitions.yaml @@ -0,0 +1,74 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/partitions/linksys,ns-partitions.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Linksys Northstar partitioning + +description: | + Linksys devices based on Broadcom Northstar architecture often use two + firmware partitions. One is used for regular booting, the other is treated as + fallback. + + This binding allows defining all fixed partitions and marking those containing + firmware. System can use that information e.g. for booting or flashing + purposes. + +maintainers: + - Rafał Miłecki <rafal@milecki.pl> + +properties: + compatible: + const: linksys,ns-partitions + + "#address-cells": + enum: [ 1, 2 ] + + "#size-cells": + enum: [ 1, 2 ] + +patternProperties: + "^partition@[0-9a-f]+$": + $ref: "partition.yaml#" + properties: + compatible: + items: + - const: linksys,ns-firmware + - const: brcm,trx + unevaluatedProperties: false + +required: + - "#address-cells" + - "#size-cells" + +additionalProperties: false + +examples: + - | + partitions { + compatible = "linksys,ns-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "boot"; + reg = <0x0 0x100000>; + read-only; + }; + + partition@100000 { + label = "nvram"; + reg = <0x100000 0x100000>; + }; + + partition@200000 { + compatible = "linksys,ns-firmware", "brcm,trx"; + reg = <0x200000 0xf00000>; + }; + + partition@1100000 { + compatible = "linksys,ns-firmware", "brcm,trx"; + reg = <0x1100000 0xf00000>; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/partitions/nvmem-cells.yaml b/Documentation/devicetree/bindings/mtd/partitions/nvmem-cells.yaml new file mode 100644 index 000000000000..5cdd2efa9132 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/partitions/nvmem-cells.yaml @@ -0,0 +1,99 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/partitions/nvmem-cells.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Nvmem cells + +description: | + Any partition containing the compatible "nvmem-cells" will register as a + nvmem provider. + Each direct subnodes represents a nvmem cell following the nvmem binding. + Nvmem binding to declare nvmem-cells can be found in: + Documentation/devicetree/bindings/nvmem/nvmem.yaml + +maintainers: + - Ansuel Smith <ansuelsmth@gmail.com> + +allOf: + - $ref: /schemas/nvmem/nvmem.yaml# + +properties: + compatible: + const: nvmem-cells + +required: + - compatible + +additionalProperties: true + +examples: + - | + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + /* ... */ + + }; + art: art@1200000 { + compatible = "nvmem-cells"; + reg = <0x1200000 0x0140000>; + label = "art"; + read-only; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_gmac1: macaddr_gmac1@0 { + reg = <0x0 0x6>; + }; + + macaddr_gmac2: macaddr_gmac2@6 { + reg = <0x6 0x6>; + }; + + pre_cal_24g: pre_cal_24g@1000 { + reg = <0x1000 0x2f20>; + }; + + pre_cal_5g: pre_cal_5g@5000{ + reg = <0x5000 0x2f20>; + }; + }; + - | + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "bootloader"; + reg = <0x000000 0x100000>; + read-only; + }; + + firmware@100000 { + compatible = "brcm,trx"; + label = "firmware"; + reg = <0x100000 0xe00000>; + }; + + calibration@f00000 { + compatible = "nvmem-cells"; + label = "calibration"; + reg = <0xf00000 0x100000>; + ranges = <0 0xf00000 0x100000>; + #address-cells = <1>; + #size-cells = <1>; + + wifi0@0 { + reg = <0x000000 0x080000>; + }; + + wifi1@80000 { + reg = <0x080000 0x080000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/qcom,nandc.yaml b/Documentation/devicetree/bindings/mtd/qcom,nandc.yaml new file mode 100644 index 000000000000..84ad7ff30121 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/qcom,nandc.yaml @@ -0,0 +1,196 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/qcom,nandc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm NAND controller + +maintainers: + - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + +properties: + compatible: + enum: + - qcom,ipq806x-nand + - qcom,ipq4019-nand + - qcom,ipq6018-nand + - qcom,ipq8074-nand + - qcom,sdx55-nand + + reg: + maxItems: 1 + + clocks: + items: + - description: Core Clock + - description: Always ON Clock + + clock-names: + items: + - const: core + - const: aon + + "#address-cells": true + "#size-cells": true + +patternProperties: + "^nand@[a-f0-9]$": + type: object + properties: + nand-bus-width: + const: 8 + + nand-ecc-strength: + enum: [1, 4, 8] + + nand-ecc-step-size: + enum: + - 512 + +allOf: + - $ref: "nand-controller.yaml#" + + - if: + properties: + compatible: + contains: + const: qcom,ipq806x-nand + then: + properties: + dmas: + items: + - description: rxtx DMA channel + + dma-names: + items: + - const: rxtx + + qcom,cmd-crci: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Must contain the ADM command type CRCI block instance number + specified for the NAND controller on the given platform + + qcom,data-crci: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Must contain the ADM data type CRCI block instance number + specified for the NAND controller on the given platform + + - if: + properties: + compatible: + contains: + enum: + - qcom,ipq4019-nand + - qcom,ipq6018-nand + - qcom,ipq8074-nand + - qcom,sdx55-nand + + then: + properties: + dmas: + items: + - description: tx DMA channel + - description: rx DMA channel + - description: cmd DMA channel + + dma-names: + items: + - const: tx + - const: rx + - const: cmd + +required: + - compatible + - reg + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,gcc-ipq806x.h> + nand-controller@1ac00000 { + compatible = "qcom,ipq806x-nand"; + reg = <0x1ac00000 0x800>; + + clocks = <&gcc EBI2_CLK>, + <&gcc EBI2_AON_CLK>; + clock-names = "core", "aon"; + + dmas = <&adm_dma 3>; + dma-names = "rxtx"; + qcom,cmd-crci = <15>; + qcom,data-crci = <3>; + + #address-cells = <1>; + #size-cells = <0>; + + nand@0 { + reg = <0>; + + nand-ecc-strength = <4>; + nand-bus-width = <8>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "boot-nand"; + reg = <0 0x58a0000>; + }; + + partition@58a0000 { + label = "fs-nand"; + reg = <0x58a0000 0x4000000>; + }; + }; + }; + }; + + #include <dt-bindings/clock/qcom,gcc-ipq4019.h> + nand-controller@79b0000 { + compatible = "qcom,ipq4019-nand"; + reg = <0x79b0000 0x1000>; + + clocks = <&gcc GCC_QPIC_CLK>, + <&gcc GCC_QPIC_AHB_CLK>; + clock-names = "core", "aon"; + + dmas = <&qpicbam 0>, + <&qpicbam 1>, + <&qpicbam 2>; + dma-names = "tx", "rx", "cmd"; + + #address-cells = <1>; + #size-cells = <0>; + + nand@0 { + reg = <0>; + nand-ecc-strength = <4>; + nand-bus-width = <8>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "boot-nand"; + reg = <0 0x58a0000>; + }; + + partition@58a0000 { + label = "fs-nand"; + reg = <0x58a0000 0x4000000>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt deleted file mode 100644 index 5647913d8837..000000000000 --- a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt +++ /dev/null @@ -1,142 +0,0 @@ -* Qualcomm NAND controller - -Required properties: -- compatible: must be one of the following: - * "qcom,ipq806x-nand" - for EBI2 NAND controller being used in IPQ806x - SoC and it uses ADM DMA - * "qcom,ipq4019-nand" - for QPIC NAND controller v1.4.0 being used in - IPQ4019 SoC and it uses BAM DMA - * "qcom,ipq6018-nand" - for QPIC NAND controller v1.5.0 being used in - IPQ6018 SoC and it uses BAM DMA - * "qcom,ipq8074-nand" - for QPIC NAND controller v1.5.0 being used in - IPQ8074 SoC and it uses BAM DMA - * "qcom,sdx55-nand" - for QPIC NAND controller v2.0.0 being used in - SDX55 SoC and it uses BAM DMA - -- reg: MMIO address range -- clocks: must contain core clock and always on clock -- clock-names: must contain "core" for the core clock and "aon" for the - always on clock - -EBI2 specific properties: -- dmas: DMA specifier, consisting of a phandle to the ADM DMA - controller node and the channel number to be used for - NAND. Refer to dma.txt and qcom_adm.txt for more details -- dma-names: must be "rxtx" -- qcom,cmd-crci: must contain the ADM command type CRCI block instance - number specified for the NAND controller on the given - platform -- qcom,data-crci: must contain the ADM data type CRCI block instance - number specified for the NAND controller on the given - platform - -QPIC specific properties: -- dmas: DMA specifier, consisting of a phandle to the BAM DMA - and the channel number to be used for NAND. Refer to - dma.txt, qcom_bam_dma.txt for more details -- dma-names: must contain all 3 channel names : "tx", "rx", "cmd" -- #address-cells: <1> - subnodes give the chip-select number -- #size-cells: <0> - -* NAND chip-select - -Each controller may contain one or more subnodes to represent enabled -chip-selects which (may) contain NAND flash chips. Their properties are as -follows. - -Required properties: -- reg: a single integer representing the chip-select - number (e.g., 0, 1, 2, etc.) -- #address-cells: see partition.txt -- #size-cells: see partition.txt - -Optional properties: -- nand-bus-width: see nand-controller.yaml -- nand-ecc-strength: see nand-controller.yaml. If not specified, then ECC strength will - be used according to chip requirement and available - OOB size. - -Each nandcs device node may optionally contain a 'partitions' sub-node, which -further contains sub-nodes describing the flash partition mapping. See -partition.txt for more detail. - -Example: - -nand-controller@1ac00000 { - compatible = "qcom,ipq806x-nand"; - reg = <0x1ac00000 0x800>; - - clocks = <&gcc EBI2_CLK>, - <&gcc EBI2_AON_CLK>; - clock-names = "core", "aon"; - - dmas = <&adm_dma 3>; - dma-names = "rxtx"; - qcom,cmd-crci = <15>; - qcom,data-crci = <3>; - - #address-cells = <1>; - #size-cells = <0>; - - nand@0 { - reg = <0>; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "boot-nand"; - reg = <0 0x58a0000>; - }; - - partition@58a0000 { - label = "fs-nand"; - reg = <0x58a0000 0x4000000>; - }; - }; - }; -}; - -nand-controller@79b0000 { - compatible = "qcom,ipq4019-nand"; - reg = <0x79b0000 0x1000>; - - clocks = <&gcc GCC_QPIC_CLK>, - <&gcc GCC_QPIC_AHB_CLK>; - clock-names = "core", "aon"; - - dmas = <&qpicbam 0>, - <&qpicbam 1>, - <&qpicbam 2>; - dma-names = "tx", "rx", "cmd"; - - #address-cells = <1>; - #size-cells = <0>; - - nand@0 { - reg = <0>; - nand-ecc-strength = <4>; - nand-bus-width = <8>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "boot-nand"; - reg = <0 0x58a0000>; - }; - - partition@58a0000 { - label = "fs-nand"; - reg = <0x58a0000 0x4000000>; - }; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/nvmem/nvmem.yaml b/Documentation/devicetree/bindings/nvmem/nvmem.yaml index 7481a9e48f19..b8dc3d2b6e92 100644 --- a/Documentation/devicetree/bindings/nvmem/nvmem.yaml +++ b/Documentation/devicetree/bindings/nvmem/nvmem.yaml @@ -20,9 +20,6 @@ description: | storage device. properties: - $nodename: - pattern: "^(eeprom|efuse|nvram)(@.*|-[0-9a-f])*$" - "#address-cells": const: 1 |