1 files changed, 153 insertions, 0 deletions
diff --git a/Documentation/sound/oss/CMI8330 b/Documentation/sound/oss/CMI8330
new file mode 100644
index 000000000000..9c439f1a6dba
--- /dev/null
+++ b/Documentation/sound/oss/CMI8330
@@ -0,0 +1,153 @@
+Documentation for CMI 8330 (SoundPRO) 
+-------------------------------------
+Alessandro Zummo <azummo@ita.flashnet.it>
+
+( Be sure to read Documentation/sound/oss/SoundPro too )
+
+
+This adapter is now directly supported by the sb driver.
+
+ The only thing you have to do is to compile the kernel sound
+support as a module and to enable kernel ISAPnP support,
+as shown below.
+
+
+CONFIG_SOUND=m
+CONFIG_SOUND_SB=m
+
+CONFIG_PNP=y
+CONFIG_ISAPNP=y
+
+
+and optionally:
+
+
+CONFIG_SOUND_MPU401=m
+
+ for MPU401 support.
+
+
+(I suggest you to use "make menuconfig" or "make xconfig" 
+ for a more comfortable configuration editing)
+
+
+
+Then you can do
+
+ modprobe sb
+
+and everything will be (hopefully) configured.
+
+You should get something similar in syslog:
+
+sb: CMI8330 detected.
+sb: CMI8330 sb base located at 0x220
+sb: CMI8330 mpu base located at 0x330
+sb: CMI8330 mail reports to Alessandro Zummo <azummo@ita.flashnet.it>
+sb: ISAPnP reports CMI 8330 SoundPRO at i/o 0x220, irq 7, dma 1,5
+
+
+
+
+The old documentation file follows for reference
+purposes.
+
+
+How to enable CMI 8330 (SOUNDPRO) soundchip on Linux
+------------------------------------------
+Stefan Laudat <Stefan.Laudat@asit.ro>
+
+[Note: The CMI 8338 is unrelated and is supported by cmpci.o]
+
+	
+	In order to use CMI8330 under Linux  you just have to use a proper isapnp.conf, a good isapnp and a little bit of patience.  I use isapnp 1.17, but
+you may get a better one I guess at http://www.roestock.demon.co.uk/isapnptools/.
+
+	Of course you will have to compile kernel sound support as module, as shown below:
+
+CONFIG_SOUND=m
+CONFIG_SOUND_OSS=m
+CONFIG_SOUND_SB=m
+CONFIG_SOUND_ADLIB=m
+CONFIG_SOUND_MPU401=m
+# Mikro$chaft sound system (kinda useful here ;))	
+CONFIG_SOUND_MSS=m
+
+	The /etc/isapnp.conf file will be:
+
+<snip below>
+
+
+(READPORT 0x0203)
+(ISOLATE PRESERVE)
+(IDENTIFY *)
+(VERBOSITY 2)
+(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING
+(VERIFYLD N)
+
+
+# WSS 
+
+(CONFIGURE CMI0001/16777472 (LD 0
+(IO 0 (SIZE 8) (BASE 0x0530))
+(IO 1 (SIZE 8) (BASE 0x0388))
+(INT 0 (IRQ 7 (MODE +E)))
+(DMA 0 (CHANNEL 0))
+(NAME "CMI0001/16777472[0]{CMI8330/C3D Audio Adapter}")
+(ACT Y)
+))
+
+# MPU
+
+(CONFIGURE CMI0001/16777472 (LD 1
+(IO 0 (SIZE 2) (BASE 0x0330))
+(INT 0 (IRQ 11 (MODE +E)))
+(NAME "CMI0001/16777472[1]{CMI8330/C3D Audio Adapter}")
+(ACT Y)
+))
+
+# Joystick
+
+(CONFIGURE CMI0001/16777472 (LD 2
+(IO 0 (SIZE 8) (BASE 0x0200))
+(NAME "CMI0001/16777472[2]{CMI8330/C3D Audio Adapter}")
+(ACT Y)
+))
+
+# SoundBlaster 
+ 
+(CONFIGURE CMI0001/16777472 (LD 3
+(IO 0 (SIZE 16) (BASE 0x0220))
+(INT 0 (IRQ 5 (MODE +E)))
+(DMA 0 (CHANNEL 1))
+(DMA 1 (CHANNEL 5))
+(NAME "CMI0001/16777472[3]{CMI8330/C3D Audio Adapter}")
+(ACT Y)
+))
+
+
+(WAITFORKEY)
+
+<end of snip>
+
+	The module sequence is trivial:
+
+/sbin/insmod soundcore
+/sbin/insmod sound
+/sbin/insmod uart401
+# insert this first
+/sbin/insmod ad1848 io=0x530 irq=7 dma=0 soundpro=1
+# The sb module is an alternative to the ad1848 (Microsoft Sound System)
+# Anyhow, this is full duplex and has MIDI
+/sbin/insmod sb io=0x220 dma=1 dma16=5 irq=5 mpu_io=0x330
+
+
+
+Alma Chao <elysian@ethereal.torsion.org> suggests the following /etc/modprobe.conf:
+
+alias sound ad1848
+alias synth0 opl3
+options ad1848 io=0x530 irq=7 dma=0 soundpro=1
+options opl3 io=0x388
+
+