diff options
Diffstat (limited to 'Documentation')
44 files changed, 972 insertions, 149 deletions
diff --git a/Documentation/ABI/testing/sysfs-class-net-qmi b/Documentation/ABI/testing/sysfs-class-net-qmi index fa5a00bb1143..7122d6264c49 100644 --- a/Documentation/ABI/testing/sysfs-class-net-qmi +++ b/Documentation/ABI/testing/sysfs-class-net-qmi @@ -21,3 +21,30 @@ Description: is responsible for coordination of driver and firmware link framing mode, changing this setting to 'Y' if the firmware is configured for 'raw-ip' mode. + +What: /sys/class/net/<iface>/qmi/add_mux +Date: March 2017 +KernelVersion: 4.11 +Contact: Bjørn Mork <bjorn@mork.no> +Description: + Unsigned integer. + + Write a number ranging from 1 to 127 to add a qmap mux + based network device, supported by recent Qualcomm based + modems. + + The network device will be called qmimux. + + Userspace is in charge of managing the qmux network device + activation and data stream setup on the modem side by + using the proper QMI protocol requests. + +What: /sys/class/net/<iface>/qmi/del_mux +Date: March 2017 +KernelVersion: 4.11 +Contact: Bjørn Mork <bjorn@mork.no> +Description: + Unsigned integer. + + Write a number ranging from 1 to 127 to delete a previously + created qmap mux based network device. diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt index 986e44387dad..facc20a3f962 100644 --- a/Documentation/admin-guide/kernel-parameters.txt +++ b/Documentation/admin-guide/kernel-parameters.txt @@ -653,6 +653,9 @@ cpuidle.off=1 [CPU_IDLE] disable the cpuidle sub-system + cpufreq.off=1 [CPU_FREQ] + disable the cpufreq sub-system + cpu_init_udelay=N [X86] Delay for N microsec between assert and de-assert of APIC INIT to start processors. This delay occurs @@ -1183,6 +1186,12 @@ functions that can be changed at run time by the set_graph_notrace file in the debugfs tracing directory. + ftrace_graph_max_depth=<uint> + [FTRACE] Used with the function graph tracer. This is + the max depth it will trace into a function. This value + can be changed at run time by the max_graph_depth file + in the tracefs tracing directory. default: 0 (no limit) + gamecon.map[2|3]= [HW,JOY] Multisystem joystick and NES/SNES/PSX pad support via parallel port (up to 5 devices per port) @@ -1716,6 +1725,12 @@ kernel and module base offset ASLR (Address Space Layout Randomization). + kasan_multi_shot + [KNL] Enforce KASAN (Kernel Address Sanitizer) to print + report on every invalid memory access. Without this + parameter KASAN will print report only for the first + invalid access. + keepinitrd [HW,ARM] kernelcore= [KNL,X86,IA-64,PPC] diff --git a/Documentation/arm64/silicon-errata.txt b/Documentation/arm64/silicon-errata.txt index a71b8095dbd8..2f66683500b8 100644 --- a/Documentation/arm64/silicon-errata.txt +++ b/Documentation/arm64/silicon-errata.txt @@ -68,3 +68,4 @@ stable kernels. | | | | | | Qualcomm Tech. | Falkor v1 | E1003 | QCOM_FALKOR_ERRATUM_1003 | | Qualcomm Tech. | Falkor v1 | E1009 | QCOM_FALKOR_ERRATUM_1009 | +| Qualcomm Tech. | QDF2400 ITS | E0065 | QCOM_QDF2400_ERRATUM_0065 | diff --git a/Documentation/cgroup-v2.txt b/Documentation/cgroup-v2.txt index 3b8449f8ac7e..49d7c997fa1e 100644 --- a/Documentation/cgroup-v2.txt +++ b/Documentation/cgroup-v2.txt @@ -1142,16 +1142,17 @@ used by the kernel. pids.max - A read-write single value file which exists on non-root cgroups. The - default is "max". + A read-write single value file which exists on non-root + cgroups. The default is "max". - Hard limit of number of processes. + Hard limit of number of processes. pids.current - A read-only single value file which exists on all cgroups. + A read-only single value file which exists on all cgroups. - The number of processes currently in the cgroup and its descendants. + The number of processes currently in the cgroup and its + descendants. Organisational operations are not blocked by cgroup policies, so it is possible to have pids.current > pids.max. This can be done by either diff --git a/Documentation/dev-tools/kcov.rst b/Documentation/dev-tools/kcov.rst index 2c41b713841f..44886c91e112 100644 --- a/Documentation/dev-tools/kcov.rst +++ b/Documentation/dev-tools/kcov.rst @@ -10,7 +10,7 @@ Note that kcov does not aim to collect as much coverage as possible. It aims to collect more or less stable coverage that is function of syscall inputs. To achieve this goal it does not collect coverage in soft/hard interrupts and instrumentation of some inherently non-deterministic parts of kernel is -disbled (e.g. scheduler, locking). +disabled (e.g. scheduler, locking). Usage ----- diff --git a/Documentation/devicetree/bindings/arm/marvell/cp110-system-controller0.txt b/Documentation/devicetree/bindings/arm/marvell/cp110-system-controller0.txt index 30c546900b60..07dbb358182c 100644 --- a/Documentation/devicetree/bindings/arm/marvell/cp110-system-controller0.txt +++ b/Documentation/devicetree/bindings/arm/marvell/cp110-system-controller0.txt @@ -45,7 +45,7 @@ The following clocks are available: - 1 15 SATA - 1 16 SATA USB - 1 17 Main - - 1 18 SD/MMC + - 1 18 SD/MMC/GOP - 1 21 Slow IO (SPI, NOR, BootROM, I2C, UART) - 1 22 USB3H0 - 1 23 USB3H1 @@ -65,7 +65,7 @@ Required properties: "cpm-audio", "cpm-communit", "cpm-nand", "cpm-ppv2", "cpm-sdio", "cpm-mg-domain", "cpm-mg-core", "cpm-xor1", "cpm-xor0", "cpm-gop-dp", "none", "cpm-pcie_x10", "cpm-pcie_x11", "cpm-pcie_x4", "cpm-pcie-xor", "cpm-sata", - "cpm-sata-usb", "cpm-main", "cpm-sd-mmc", "none", "none", "cpm-slow-io", + "cpm-sata-usb", "cpm-main", "cpm-sd-mmc-gop", "none", "none", "cpm-slow-io", "cpm-usb3h0", "cpm-usb3h1", "cpm-usb3dev", "cpm-eip150", "cpm-eip197"; Example: @@ -78,6 +78,6 @@ Example: gate-clock-output-names = "cpm-audio", "cpm-communit", "cpm-nand", "cpm-ppv2", "cpm-sdio", "cpm-mg-domain", "cpm-mg-core", "cpm-xor1", "cpm-xor0", "cpm-gop-dp", "none", "cpm-pcie_x10", "cpm-pcie_x11", "cpm-pcie_x4", "cpm-pcie-xor", "cpm-sata", - "cpm-sata-usb", "cpm-main", "cpm-sd-mmc", "none", "none", "cpm-slow-io", + "cpm-sata-usb", "cpm-main", "cpm-sd-mmc-gop", "none", "none", "cpm-slow-io", "cpm-usb3h0", "cpm-usb3h1", "cpm-usb3dev", "cpm-eip150", "cpm-eip197"; }; diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt index a78265993665..ca5204b3bc21 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt @@ -4,7 +4,6 @@ Required properties: - compatible: value should be one of the following "samsung,exynos3250-mipi-dsi" /* for Exynos3250/3472 SoCs */ "samsung,exynos4210-mipi-dsi" /* for Exynos4 SoCs */ - "samsung,exynos4415-mipi-dsi" /* for Exynos4415 SoC */ "samsung,exynos5410-mipi-dsi" /* for Exynos5410/5420/5440 SoCs */ "samsung,exynos5422-mipi-dsi" /* for Exynos5422/5800 SoCs */ "samsung,exynos5433-mipi-dsi" /* for Exynos5433 SoCs */ diff --git a/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt b/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt index 18645e0228b0..5837402c3ade 100644 --- a/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt +++ b/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt @@ -11,7 +11,6 @@ Required properties: "samsung,s5pv210-fimd"; /* for S5PV210 SoC */ "samsung,exynos3250-fimd"; /* for Exynos3250/3472 SoCs */ "samsung,exynos4210-fimd"; /* for Exynos4 SoCs */ - "samsung,exynos4415-fimd"; /* for Exynos4415 SoC */ "samsung,exynos5250-fimd"; /* for Exynos5250 SoCs */ "samsung,exynos5420-fimd"; /* for Exynos5420/5422/5800 SoCs */ diff --git a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt index ea9c1c9607f6..520d61dad6dd 100644 --- a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt @@ -13,7 +13,7 @@ Required Properties: - "rockchip,rk2928-dw-mshc": for Rockchip RK2928 and following, before RK3288 - "rockchip,rk3288-dw-mshc": for Rockchip RK3288 - - "rockchip,rk1108-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK1108 + - "rockchip,rv1108-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RV1108 - "rockchip,rk3036-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3036 - "rockchip,rk3368-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3368 - "rockchip,rk3399-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3399 diff --git a/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt b/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt index 10587bdadbbe..26c77d985faf 100644 --- a/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt +++ b/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt @@ -2,11 +2,14 @@ Required properties: - compatible: should contain one of "brcm,genet-v1", "brcm,genet-v2", - "brcm,genet-v3", "brcm,genet-v4". + "brcm,genet-v3", "brcm,genet-v4", "brcm,genet-v5". - reg: address and length of the register set for the device -- interrupts: must be two cells, the first cell is the general purpose - interrupt line, while the second cell is the interrupt for the ring - RX and TX queues operating in ring mode +- interrupts and/or interrupts-extended: must be two cells, the first cell + is the general purpose interrupt line, while the second cell is the + interrupt for the ring RX and TX queues operating in ring mode. An + optional third interrupt cell for Wake-on-LAN can be specified. + See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + for information on the property specifics. - phy-mode: see ethernet.txt file in the same directory - #address-cells: should be 1 - #size-cells: should be 1 @@ -29,15 +32,15 @@ Optional properties: Required child nodes: -- mdio bus node: this node should always be present regarless of the PHY +- mdio bus node: this node should always be present regardless of the PHY configuration of the GENET instance MDIO bus node required properties: - compatible: should contain one of "brcm,genet-mdio-v1", "brcm,genet-mdio-v2" - "brcm,genet-mdio-v3", "brcm,genet-mdio-v4", the version has to match the - parent node compatible property (e.g: brcm,genet-v4 pairs with - brcm,genet-mdio-v4) + "brcm,genet-mdio-v3", "brcm,genet-mdio-v4", "brcm,genet-mdio-v5", the version + has to match the parent node compatible property (e.g: brcm,genet-v4 pairs + with brcm,genet-mdio-v4) - reg: address and length relative to the parent node base register address - #address-cells: address cell for MDIO bus addressing, should be 1 - #size-cells: size of the cells for MDIO bus addressing, should be 0 diff --git a/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt b/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt index ab0bb4247d14..4648948f7c3b 100644 --- a/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt +++ b/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt @@ -2,8 +2,9 @@ Required properties: - compatible: should one from "brcm,genet-mdio-v1", "brcm,genet-mdio-v2", - "brcm,genet-mdio-v3", "brcm,genet-mdio-v4" or "brcm,unimac-mdio" -- reg: address and length of the regsiter set for the device, first one is the + "brcm,genet-mdio-v3", "brcm,genet-mdio-v4", "brcm,genet-mdio-v5" or + "brcm,unimac-mdio" +- reg: address and length of the register set for the device, first one is the base register, and the second one is optional and for indirect accesses to larger than 16-bits MDIO transactions - reg-names: name(s) of the register must be "mdio" and optional "mdio_indir_rw" diff --git a/Documentation/devicetree/bindings/net/can/holt_hi311x.txt b/Documentation/devicetree/bindings/net/can/holt_hi311x.txt new file mode 100644 index 000000000000..23aa94eab207 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/holt_hi311x.txt @@ -0,0 +1,24 @@ +* Holt HI-311X stand-alone CAN controller device tree bindings + +Required properties: + - compatible: Should be one of the following: + - "holt,hi3110" for HI-3110 + - reg: SPI chip select. + - clocks: The clock feeding the CAN controller. + - interrupt-parent: The parent interrupt controller. + - interrupts: Should contain IRQ line for the CAN controller. + +Optional properties: + - vdd-supply: Regulator that powers the CAN controller. + - xceiver-supply: Regulator that powers the CAN transceiver. + +Example: + can0: can@1 { + compatible = "holt,hi3110"; + reg = <1>; + clocks = <&clk32m>; + interrupt-parent = <&gpio4>; + interrupts = <13 IRQ_TYPE_EDGE_RISING>; + vdd-supply = <®5v0>; + xceiver-supply = <®5v0>; + }; diff --git a/Documentation/devicetree/bindings/net/can/ti_hecc.txt b/Documentation/devicetree/bindings/net/can/ti_hecc.txt new file mode 100644 index 000000000000..e0f0a7cfe329 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/ti_hecc.txt @@ -0,0 +1,32 @@ +Texas Instruments High End CAN Controller (HECC) +================================================ + +This file provides information, what the device node +for the hecc interface contains. + +Required properties: +- compatible: "ti,am3517-hecc" +- reg: addresses and lengths of the register spaces for 'hecc', 'hecc-ram' + and 'mbx' +- reg-names :"hecc", "hecc-ram", "mbx" +- interrupts: interrupt mapping for the hecc interrupts sources +- clocks: clock phandles (see clock bindings for details) + +Optional properties: +- ti,use-hecc1int: if provided configures HECC to produce all interrupts + on HECC1INT interrupt line. By default HECC0INT interrupt + line will be used. +- xceiver-supply: regulator that powers the CAN transceiver + +Example: + +For am3517evm board: + hecc: can@5c050000 { + compatible = "ti,am3517-hecc"; + reg = <0x5c050000 0x80>, + <0x5c053000 0x180>, + <0x5c052000 0x200>; + reg-names = "hecc", "hecc-ram", "mbx"; + interrupts = <24>; + clocks = <&hecc_ck>; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/lan9303.txt b/Documentation/devicetree/bindings/net/dsa/lan9303.txt new file mode 100644 index 000000000000..04f2965a4467 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/lan9303.txt @@ -0,0 +1,105 @@ +SMSC/MicroChip LAN9303 three port ethernet switch +------------------------------------------------- + +Required properties: + +- compatible: should be + - "smsc,lan9303-i2c" for I2C managed mode + or + - "smsc,lan9303-mdio" for mdio managed mode + +Optional properties: + +- reset-gpios: GPIO to be used to reset the whole device +- reset-duration: reset duration in milliseconds, defaults to 200 ms + +Subnodes: + +The integrated switch subnode should be specified according to the binding +described in dsa/dsa.txt. The CPU port of this switch is always port 0. + +Note: always use 'reg = <0/1/2>;' for the three DSA ports, even if the device is +configured to use 1/2/3 instead. This hardware configuration will be +auto-detected and mapped accordingly. + +Example: + +I2C managed mode: + + master: masterdevice@X { + status = "okay"; + + fixed-link { /* RMII fixed link to LAN9303 */ + speed = <100>; + full-duplex; + }; + }; + + switch: switch@a { + compatible = "smsc,lan9303-i2c"; + reg = <0xa>; + status = "okay"; + reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>; + reset-duration = <200>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { /* RMII fixed link to master */ + reg = <0>; + label = "cpu"; + ethernet = <&master>; + }; + + port@1 { /* external port 1 */ + reg = <1>; + label = "lan1; + }; + + port@2 { /* external port 2 */ + reg = <2>; + label = "lan2"; + }; + }; + }; + +MDIO managed mode: + + master: masterdevice@X { + status = "okay"; + phy-handle = <&switch>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch: switch-phy@0 { + compatible = "smsc,lan9303-mdio"; + reg = <0>; + reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>; + reset-duration = <100>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "cpu"; + ethernet = <&master>; + }; + + port@1 { /* external port 1 */ + reg = <1>; + label = "lan1; + }; + + port@2 { /* external port 2 */ + reg = <2>; + label = "lan2"; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/mt7530.txt b/Documentation/devicetree/bindings/net/dsa/mt7530.txt new file mode 100644 index 000000000000..a9bc27b93ee3 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/mt7530.txt @@ -0,0 +1,92 @@ +Mediatek MT7530 Ethernet switch +================================ + +Required properties: + +- compatible: Must be compatible = "mediatek,mt7530"; +- #address-cells: Must be 1. +- #size-cells: Must be 0. +- mediatek,mcm: Boolean; if defined, indicates that either MT7530 is the part + on multi-chip module belong to MT7623A has or the remotely standalone + chip as the function MT7623N reference board provided for. +- core-supply: Phandle to the regulator node necessary for the core power. +- io-supply: Phandle to the regulator node necessary for the I/O power. + See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt + for details for the regulator setup on these boards. + +If the property mediatek,mcm isn't defined, following property is required + +- reset-gpios: Should be a gpio specifier for a reset line. + +Else, following properties are required + +- resets : Phandle pointing to the system reset controller with + line index for the ethsys. +- reset-names : Should be set to "mcm". + +Required properties for the child nodes within ports container: + +- reg: Port address described must be 6 for CPU port and from 0 to 5 for + user ports. +- phy-mode: String, must be either "trgmii" or "rgmii" for port labeled + "cpu". + +See Documentation/devicetree/bindings/dsa/dsa.txt for a list of additional +required, optional properties and how the integrated switch subnodes must +be specified. + +Example: + + &mdio0 { + switch@0 { + compatible = "mediatek,mt7530"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + core-supply = <&mt6323_vpa_reg>; + io-supply = <&mt6323_vemc3v3_reg>; + reset-gpios = <&pio 33 0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + port@0 { + reg = <0>; + label = "lan0"; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "trgmii"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/ftgmac100.txt b/Documentation/devicetree/bindings/net/ftgmac100.txt new file mode 100644 index 000000000000..c1ce1680246f --- /dev/null +++ b/Documentation/devicetree/bindings/net/ftgmac100.txt @@ -0,0 +1,35 @@ +* Faraday Technology FTGMAC100 gigabit ethernet controller + +Required properties: +- compatible: "faraday,ftgmac100" + + Must also contain one of these if used as part of an Aspeed AST2400 + or 2500 family SoC as they have some subtle tweaks to the + implementation: + + - "aspeed,ast2400-mac" + - "aspeed,ast2500-mac" + +- reg: Address and length of the register set for the device +- interrupts: Should contain ethernet controller interrupt + +Optional properties: +- phy-mode: See ethernet.txt file in the same directory. If the property is + absent, "rgmii" is assumed. Supported values are "rgmii*" and "rmii" for + aspeed parts. Other (unknown) parts will accept any value. +- use-ncsi: Use the NC-SI stack instead of an MDIO PHY. Currently assumes + rmii (100bT) but kept as a separate property in case NC-SI grows support + for a gigabit link. +- no-hw-checksum: Used to disable HW checksum support. Here for backward + compatibility as the driver now should have correct defaults based on + the SoC. + +Example: + + mac0: ethernet@1e660000 { + compatible = "aspeed,ast2500-mac", "faraday,ftgmac100"; + reg = <0x1e660000 0x180>; + interrupts = <2>; + status = "okay"; + use-ncsi; + }; diff --git a/Documentation/devicetree/bindings/net/ieee802154/ca8210.txt b/Documentation/devicetree/bindings/net/ieee802154/ca8210.txt new file mode 100644 index 000000000000..a1046e636fa1 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ieee802154/ca8210.txt @@ -0,0 +1,28 @@ +* CA8210 IEEE 802.15.4 * + +Required properties: + - compatible: Should be "cascoda,ca8210" + - reg: Controlling chip select + - spi-max-frequency: Maximum clock speed, should be *less than* + 4000000 + - spi-cpol: Requires inverted clock polarity + - reset-gpio: GPIO attached to reset + - irq-gpio: GPIO attached to IRQ +Optional properties: + - extclock-enable: Include for the ca8210 to route its 16MHz clock + to an output + - extclock-freq: Frequency in Hz of the external clock + - extclock-gpio: GPIO of the ca8210 to output the clock on + +Example: + ca8210@0 { + compatible = "cascoda,ca8210"; + reg = <0>; + spi-max-frequency = <3000000>; + spi-cpol; + reset-gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>; + irq-gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>; + extclock-enable; + extclock-freq = 16000000; + extclock-gpio = 2; + }; diff --git a/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt b/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt index 9417e54c26c0..ccdabdcc8618 100644 --- a/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt +++ b/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt @@ -7,17 +7,20 @@ interface. Required properties: - compatible: "marvell,orion-mdio" -- reg: address and length of the SMI register +- reg: address and length of the MDIO registers. When an interrupt is + not present, the length is the size of the SMI register (4 bytes) + otherwise it must be 0x84 bytes to cover the interrupt control + registers. Optional properties: - interrupts: interrupt line number for the SMI error/done interrupt -- clocks: Phandle to the clock control device and gate bit +- clocks: phandle for up to three required clocks for the MDIO instance The child nodes of the MDIO driver are the individual PHY devices connected to this MDIO bus. They must have a "reg" property given the PHY address on the MDIO bus. -Example at the SoC level: +Example at the SoC level without an interrupt property: mdio { #address-cells = <1>; @@ -26,6 +29,16 @@ mdio { reg = <0xd0072004 0x4>; }; +Example with an interrupt property: + +mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "marvell,orion-mdio"; + reg = <0xd0072004 0x84>; + interrupts = <30>; +}; + And at the board level: mdio { diff --git a/Documentation/devicetree/bindings/net/marvell-pp2.txt b/Documentation/devicetree/bindings/net/marvell-pp2.txt index 4754364df4c6..6b4956beff8c 100644 --- a/Documentation/devicetree/bindings/net/marvell-pp2.txt +++ b/Documentation/devicetree/bindings/net/marvell-pp2.txt @@ -1,17 +1,28 @@ -* Marvell Armada 375 Ethernet Controller (PPv2) +* Marvell Armada 375 Ethernet Controller (PPv2.1) + Marvell Armada 7K/8K Ethernet Controller (PPv2.2) Required properties: -- compatible: should be "marvell,armada-375-pp2" +- compatible: should be one of: + "marvell,armada-375-pp2" + "marvell,armada-7k-pp2" - reg: addresses and length of the register sets for the device. - Must contain the following register sets: + For "marvell,armada-375-pp2", must contain the following register + sets: - common controller registers - LMS registers - In addition, at least one port register set is required. -- clocks: a pointer to the reference clocks for this device, consequently: - - main controller clock - - GOP clock -- clock-names: names of used clocks, must be "pp_clk" and "gop_clk". + - one register area per Ethernet port + For "marvell,armada-7k-pp2", must contain the following register + sets: + - packet processor registers + - networking interfaces registers + +- clocks: pointers to the reference clocks for this device, consequently: + - main controller clock (for both armada-375-pp2 and armada-7k-pp2) + - GOP clock (for both armada-375-pp2 and armada-7k-pp2) + - MG clock (only for armada-7k-pp2) +- clock-names: names of used clocks, must be "pp_clk", "gop_clk" and + "mg_clk" (the latter only for armada-7k-pp2). The ethernet ports are represented by subnodes. At least one port is required. @@ -19,8 +30,10 @@ required. Required properties (port): - interrupts: interrupt for the port -- port-id: should be '0' or '1' for ethernet ports, and '2' for the - loopback port +- port-id: ID of the port from the MAC point of view +- gop-port-id: only for marvell,armada-7k-pp2, ID of the port from the + GOP (Group Of Ports) point of view. This ID is used to index the + per-port registers in the second register area. - phy-mode: See ethernet.txt file in the same directory Optional properties (port): @@ -29,7 +42,7 @@ Optional properties (port): - phy: a phandle to a phy node defining the PHY address (as the reg property, a single integer). -Example: +Example for marvell,armada-375-pp2: ethernet@f0000 { compatible = "marvell,armada-375-pp2"; @@ -57,3 +70,30 @@ ethernet@f0000 { phy-mode = "gmii"; }; }; + +Example for marvell,armada-7k-pp2: + +cpm_ethernet: ethernet@0 { + compatible = "marvell,armada-7k-pp22"; + reg = <0x0 0x100000>, <0x129000 0xb000>; + clocks = <&cpm_syscon0 1 3>, <&cpm_syscon0 1 9>, <&cpm_syscon0 1 5>; + clock-names = "pp_clk", "gop_clk", "gp_clk"; + + eth0: eth0 { + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + port-id = <0>; + gop-port-id = <0>; + }; + + eth1: eth1 { + interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; + port-id = <1>; + gop-port-id = <2>; + }; + + eth2: eth2 { + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; + port-id = <2>; + gop-port-id = <3>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nokia-bluetooth.txt b/Documentation/devicetree/bindings/net/nokia-bluetooth.txt new file mode 100644 index 000000000000..42be7dc9a70b --- /dev/null +++ b/Documentation/devicetree/bindings/net/nokia-bluetooth.txt @@ -0,0 +1,51 @@ +Nokia Bluetooth Chips +--------------------- + +Nokia phones often come with UART connected bluetooth chips from different +vendors and modified device API. Those devices speak a protocol named H4+ +(also known as h4p) by Nokia, which is similar to the H4 protocol from the +Bluetooth standard. In addition to the H4 protocol it specifies two more +UART status lines for wakeup of UART transceivers to improve power management +and a few new packet types used to negotiate uart speed. + +Required properties: + + - compatible: should contain "nokia,h4p-bluetooth" as well as one of the following: + * "brcm,bcm2048-nokia" + * "ti,wl1271-bluetooth-nokia" + - reset-gpios: GPIO specifier, used to reset the BT module (active low) + - bluetooth-wakeup-gpios: GPIO specifier, used to wakeup the BT module (active high) + - host-wakeup-gpios: GPIO specifier, used to wakeup the host processor (active high) + - clock-names: should be "sysclk" + - clocks: should contain a clock specifier for every name in clock-names + +Optional properties: + + - None + +Example: + +/ { + /* controlled (enabled/disabled) directly by BT module */ + bluetooth_clk: vctcxo { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <38400000>; + }; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; + + bluetooth { + compatible = "ti,wl1271-bluetooth-nokia", "nokia,h4p-bluetooth"; + + reset-gpios = <&gpio1 26 GPIO_ACTIVE_LOW>; /* gpio26 */ + host-wakeup-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>; /* gpio101 */ + bluetooth-wakeup-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>; /* gpio37 */ + + clocks = <&bluetooth_clk>; + clock-names = "sysclk"; + }; +}; diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt index d3bfc2b30fb5..f652b0c384ce 100644 --- a/Documentation/devicetree/bindings/net/stmmac.txt +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -28,9 +28,9 @@ Optional properties: clocks may be specified in derived bindings. - clock-names: One name for each entry in the clocks property, the first one should be "stmmaceth" and the second one should be "pclk". -- clk_ptp_ref: this is the PTP reference clock; in case of the PTP is - available this clock is used for programming the Timestamp Addend Register. - If not passed then the system clock will be used and this is fine on some +- ptp_ref: this is the PTP reference clock; in case of the PTP is available + this clock is used for programming the Timestamp Addend Register. If not + passed then the system clock will be used and this is fine on some platforms. - tx-fifo-depth: See ethernet.txt file in the same directory - rx-fifo-depth: See ethernet.txt file in the same directory @@ -72,7 +72,45 @@ Optional properties: - snps,mb: mixed-burst - snps,rb: rebuild INCRx Burst - mdio: with compatible = "snps,dwmac-mdio", create and register mdio bus. - +- Multiple RX Queues parameters: below the list of all the parameters to + configure the multiple RX queues: + - snps,rx-queues-to-use: number of RX queues to be used in the driver + - Choose one of these RX scheduling algorithms: + - snps,rx-sched-sp: Strict priority + - snps,rx-sched-wsp: Weighted Strict priority + - For each RX queue + - Choose one of these modes: + - snps,dcb-algorithm: Queue to be enabled as DCB + - snps,avb-algorithm: Queue to be enabled as AVB + - snps,map-to-dma-channel: Channel to map + - Specifiy specific packet routing: + - snps,route-avcp: AV Untagged Control packets + - snps,route-ptp: PTP Packets + - snps,route-dcbcp: DCB Control Packets + - snps,route-up: Untagged Packets + - snps,route-multi-broad: Multicast & Broadcast Packets + - snps,priority: RX queue priority (Range: 0x0 to 0xF) +- Multiple TX Queues parameters: below the list of all the parameters to + configure the multiple TX queues: + - snps,tx-queues-to-use: number of TX queues to be used in the driver + - Choose one of these TX scheduling algorithms: + - snps,tx-sched-wrr: Weighted Round Robin + - snps,tx-sched-wfq: Weighted Fair Queuing + - snps,tx-sched-dwrr: Deficit Weighted Round Robin + - snps,tx-sched-sp: Strict priority + - For each TX queue + - snps,weight: TX queue weight (if using a DCB weight algorithm) + - Choose one of these modes: + - snps,dcb-algorithm: TX queue will be working in DCB + - snps,avb-algorithm: TX queue will be working in AVB + [Attention] Queue 0 is reserved for legacy traffic + and so no AVB is available in this queue. + - Configure Credit Base Shaper (if AVB Mode selected): + - snps,send_slope: enable Low Power Interface + - snps,idle_slope: unlock on WoL + - snps,high_credit: max write outstanding req. limit + - snps,low_credit: max read outstanding req. limit + - snps,priority: TX queue priority (Range: 0x0 to 0xF) Examples: stmmac_axi_setup: stmmac-axi-config { @@ -81,6 +119,35 @@ Examples: snps,blen = <256 128 64 32 0 0 0>; }; + mtl_rx_setup: rx-queues-config { + snps,rx-queues-to-use = <1>; + snps,rx-sched-sp; + queue0 { + snps,dcb-algorithm; + snps,map-to-dma-channel = <0x0>; + snps,priority = <0x0>; + }; + }; + + mtl_tx_setup: tx-queues-config { + snps,tx-queues-to-use = <2>; + snps,tx-sched-wrr; + queue0 { + snps,weight = <0x10>; + snps,dcb-algorithm; + snps,priority = <0x0>; + }; + + queue1 { + snps,avb-algorithm; + snps,send_slope = <0x1000>; + snps,idle_slope = <0x1000>; + snps,high_credit = <0x3E800>; + snps,low_credit = <0xFFC18000>; + snps,priority = <0x1>; + }; + }; + gmac0: ethernet@e0800000 { compatible = "st,spear600-gmac"; reg = <0xe0800000 0x8000>; @@ -104,4 +171,6 @@ Examples: phy1: ethernet-phy@0 { }; }; + snps,mtl-rx-config = <&mtl_rx_setup>; + snps,mtl-tx-config = <&mtl_tx_setup>; }; diff --git a/Documentation/devicetree/bindings/net/ti,wilink-st.txt b/Documentation/devicetree/bindings/net/ti,wilink-st.txt new file mode 100644 index 000000000000..cbad73a84ac4 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ti,wilink-st.txt @@ -0,0 +1,35 @@ +TI WiLink 7/8 (wl12xx/wl18xx) Shared Transport BT/FM/GPS devices + +TI WiLink devices have a UART interface for providing Bluetooth, FM radio, +and GPS over what's called "shared transport". The shared transport is +standard BT HCI protocol with additional channels for the other functions. + +These devices also have a separate WiFi interface as described in +wireless/ti,wlcore.txt. + +This bindings follows the UART slave device binding in +../serial/slave-device.txt. + +Required properties: + - compatible: should be one of the following: + "ti,wl1271-st" + "ti,wl1273-st" + "ti,wl1831-st" + "ti,wl1835-st" + "ti,wl1837-st" + +Optional properties: + - enable-gpios : GPIO signal controlling enabling of BT. Active high. + - vio-supply : Vio input supply (1.8V) + - vbat-supply : Vbat input supply (2.9-4.8V) + +Example: + +&serial0 { + compatible = "ns16550a"; + ... + bluetooth { + compatible = "ti,wl1835-st"; + enable-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/brcm,nsp-usb3-phy.txt b/Documentation/devicetree/bindings/phy/brcm,nsp-usb3-phy.txt deleted file mode 100644 index e68ae5dec9c9..000000000000 --- a/Documentation/devicetree/bindings/phy/brcm,nsp-usb3-phy.txt +++ /dev/null @@ -1,39 +0,0 @@ -Broadcom USB3 phy binding for northstar plus SoC -The USB3 phy is internal to the SoC and is accessed using mdio interface. - -Required mdio bus properties: -- reg: Should be 0x0 for SoC internal USB3 phy -- #address-cells: must be 1 -- #size-cells: must be 0 - -Required USB3 PHY properties: -- compatible: should be "brcm,nsp-usb3-phy" -- reg: USB3 Phy address on SoC internal MDIO bus and it should be 0x10. -- usb3-ctrl-syscon: handler of syscon node defining physical address - of usb3 control register. -- #phy-cells: must be 0 - -Required usb3 control properties: -- compatible: should be "brcm,nsp-usb3-ctrl" -- reg: offset and length of the control registers - -Example: - - mdio@0 { - reg = <0x0>; - #address-cells = <1>; - #size-cells = <0>; - - usb3_phy: usb-phy@10 { - compatible = "brcm,nsp-usb3-phy"; - reg = <0x10>; - usb3-ctrl-syscon = <&usb3_ctrl>; - #phy-cells = <0>; - status = "disabled"; - }; - }; - - usb3_ctrl: syscon@104408 { - compatible = "brcm,nsp-usb3-ctrl", "syscon"; - reg = <0x104408 0x3fc>; - }; diff --git a/Documentation/devicetree/bindings/powerpc/4xx/emac.txt b/Documentation/devicetree/bindings/powerpc/4xx/emac.txt index 712baf6c3e24..44b842b6ca15 100644 --- a/Documentation/devicetree/bindings/powerpc/4xx/emac.txt +++ b/Documentation/devicetree/bindings/powerpc/4xx/emac.txt @@ -71,6 +71,9 @@ For Axon it can be absent, though my current driver doesn't handle phy-address yet so for now, keep 0x00ffffff in it. + - phy-handle : Used to describe configurations where a external PHY + is used. Please refer to: + Documentation/devicetree/bindings/net/ethernet.txt - rx-fifo-size-gige : 1 cell, Rx fifo size in bytes for 1000 Mb/sec operations (if absent the value is the same as rx-fifo-size). For Axon, either absent or 2048. @@ -81,8 +84,22 @@ offload, phandle of the TAH device node. - tah-channel : 1 cell, optional. If appropriate, channel used on the TAH engine. + - fixed-link : Fixed-link subnode describing a link to a non-MDIO + managed entity. See + Documentation/devicetree/bindings/net/fixed-link.txt + for details. + - mdio subnode : When the EMAC has a phy connected to its local + mdio, which us supported by the kernel's network + PHY library in drivers/net/phy, there must be device + tree subnode with the following required properties: + - #address-cells: Must be <1>. + - #size-cells: Must be <0>. - Example: + For PHY definitions: Please refer to + Documentation/devicetree/bindings/net/phy.txt and + Documentation/devicetree/bindings/net/ethernet.txt + + Examples: EMAC0: ethernet@40000800 { device_type = "network"; @@ -104,6 +121,48 @@ zmii-channel = <0>; }; + EMAC1: ethernet@ef600c00 { + device_type = "network"; + compatible = "ibm,emac-apm821xx", "ibm,emac4sync"; + interrupt-parent = <&EMAC1>; + interrupts = <0 1>; + #interrupt-cells = <1>; + #address-cells = <0>; + #size-cells = <0>; + interrupt-map = <0 &UIC2 0x10 IRQ_TYPE_LEVEL_HIGH /* Status */ + 1 &UIC2 0x14 IRQ_TYPE_LEVEL_HIGH /* Wake */>; + reg = <0xef600c00 0x000000c4>; + local-mac-address = [000000000000]; /* Filled in by U-Boot */ + mal-device = <&MAL0>; + mal-tx-channel = <0>; + mal-rx-channel = <0>; + cell-index = <0>; + max-frame-size = <9000>; + rx-fifo-size = <16384>; + tx-fifo-size = <2048>; + fifo-entry-size = <10>; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + phy-map = <0x00000000>; + rgmii-device = <&RGMII0>; + rgmii-channel = <0>; + tah-device = <&TAH0>; + tah-channel = <0>; + has-inverted-stacr-oc; + has-new-stacr-staopc; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; + }; + }; + + ii) McMAL node Required properties: @@ -145,4 +204,3 @@ - revision : as provided by the RGMII new version register if available. For Axon: 0x0000012a - diff --git a/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt b/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt index c3f6546ebac7..6a23ad9ac53a 100644 --- a/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt @@ -45,7 +45,7 @@ Required Properties: Optional Properties: - reg-names: In addition to the required properties, the following are optional - "efuse-address" - Contains efuse base address used to pick up ABB info. - - "ldo-address" - Contains address of ABB LDO overide register address. + - "ldo-address" - Contains address of ABB LDO override register. "efuse-address" is required for this. - ti,ldovbb-vset-mask - Required if ldo-address is set, mask for LDO override register to provide override vset value. diff --git a/Documentation/devicetree/bindings/rng/omap_rng.txt b/Documentation/devicetree/bindings/rng/omap_rng.txt index 471477299ece..9cf7876ab434 100644 --- a/Documentation/devicetree/bindings/rng/omap_rng.txt +++ b/Documentation/devicetree/bindings/rng/omap_rng.txt @@ -12,7 +12,8 @@ Required properties: - reg : Offset and length of the register set for the module - interrupts : the interrupt number for the RNG module. Used for "ti,omap4-rng" and "inside-secure,safexcel-eip76" -- clocks: the trng clock source +- clocks: the trng clock source. Only mandatory for the + "inside-secure,safexcel-eip76" compatible. Example: /* AM335x */ diff --git a/Documentation/devicetree/bindings/usb/usb251xb.txt b/Documentation/devicetree/bindings/usb/usb251xb.txt index 0c065f77658f..3957d4edaa74 100644 --- a/Documentation/devicetree/bindings/usb/usb251xb.txt +++ b/Documentation/devicetree/bindings/usb/usb251xb.txt @@ -7,18 +7,18 @@ Required properties : - compatible : Should be "microchip,usb251xb" or one of the specific types: "microchip,usb2512b", "microchip,usb2512bi", "microchip,usb2513b", "microchip,usb2513bi", "microchip,usb2514b", "microchip,usb2514bi" - - hub-reset-gpios : Should specify the gpio for hub reset + - reset-gpios : Should specify the gpio for hub reset + - reg : I2C address on the selected bus (default is <0x2C>) Optional properties : - - reg : I2C address on the selected bus (default is <0x2C>) - skip-config : Skip Hub configuration, but only send the USB-Attach command - - vendor-id : USB Vendor ID of the hub (16 bit, default is 0x0424) - - product-id : USB Product ID of the hub (16 bit, default depends on type) - - device-id : USB Device ID of the hub (16 bit, default is 0x0bb3) - - language-id : USB Language ID (16 bit, default is 0x0000) - - manufacturer : USB Manufacturer string (max 31 characters long) - - product : USB Product string (max 31 characters long) - - serial : USB Serial string (max 31 characters long) + - vendor-id : Set USB Vendor ID of the hub (16 bit, default is 0x0424) + - product-id : Set USB Product ID of the hub (16 bit, default depends on type) + - device-id : Set USB Device ID of the hub (16 bit, default is 0x0bb3) + - language-id : Set USB Language ID (16 bit, default is 0x0000) + - manufacturer : Set USB Manufacturer string (max 31 characters long) + - product : Set USB Product string (max 31 characters long) + - serial : Set USB Serial string (max 31 characters long) - {bus,self}-powered : selects between self- and bus-powered operation (default is self-powered) - disable-hi-speed : disable USB Hi-Speed support @@ -31,8 +31,10 @@ Optional properties : (default is individual) - dynamic-power-switching : enable auto-switching from self- to bus-powered operation if the local power source is removed or unavailable - - oc-delay-{100us,4ms,8ms,16ms} : set over current timer delay (default is 8ms) - - compound-device : indicated the hub is part of a compound device + - oc-delay-us : Delay time (in microseconds) for filtering the over-current + sense inputs. Valid values are 100, 4000, 8000 (default) and 16000. If + an invalid value is given, the default is used instead. + - compound-device : indicate the hub is part of a compound device - port-mapping-mode : enable port mapping mode - string-support : enable string descriptor support (required for manufacturer, product and serial string configuration) @@ -40,34 +42,15 @@ Optional properties : device connected. - sp-disabled-ports : Specifies the ports which will be self-power disabled - bp-disabled-ports : Specifies the ports which will be bus-power disabled - - max-sp-power : Specifies the maximum current the hub consumes from an - upstream port when operating as self-powered hub including the power - consumption of a permanently attached peripheral if the hub is - configured as a compound device. The value is given in mA in a 0 - 500 - range (default is 2). - - max-bp-power : Specifies the maximum current the hub consumes from an - upstream port when operating as bus-powered hub including the power - consumption of a permanently attached peripheral if the hub is - configured as a compound device. The value is given in mA in a 0 - 500 - range (default is 100). - - max-sp-current : Specifies the maximum current the hub consumes from an - upstream port when operating as self-powered hub EXCLUDING the power - consumption of a permanently attached peripheral if the hub is - configured as a compound device. The value is given in mA in a 0 - 500 - range (default is 2). - - max-bp-current : Specifies the maximum current the hub consumes from an - upstream port when operating as bus-powered hub EXCLUDING the power - consumption of a permanently attached peripheral if the hub is - configured as a compound device. The value is given in mA in a 0 - 500 - range (default is 100). - - power-on-time : Specifies the time it takes from the time the host initiates - the power-on sequence to a port until the port has adequate power. The - value is given in ms in a 0 - 510 range (default is 100ms). + - power-on-time-ms : Specifies the time it takes from the time the host + initiates the power-on sequence to a port until the port has adequate + power. The value is given in ms in a 0 - 510 range (default is 100ms). Examples: usb2512b@2c { compatible = "microchip,usb2512b"; - hub-reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; + reg = <0x2c>; + reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; }; usb2514b@2c { diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index ec0bfb9bbebd..36b4d8a3fe6c 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -51,6 +51,7 @@ brcm Broadcom Corporation buffalo Buffalo, Inc. calxeda Calxeda capella Capella Microsystems, Inc +cascoda Cascoda, Ltd. cavium Cavium, Inc. cdns Cadence Design Systems Inc. ceva Ceva, Inc. diff --git a/Documentation/extcon/intel-int3496.txt b/Documentation/extcon/intel-int3496.txt index af0b366c25b7..8155dbc7fad3 100644 --- a/Documentation/extcon/intel-int3496.txt +++ b/Documentation/extcon/intel-int3496.txt @@ -20,3 +20,8 @@ Index 1: The output gpio for enabling Vbus output from the device to the otg Index 2: The output gpio for muxing of the data pins between the USB host and the USB peripheral controller, write 1 to mux to the peripheral controller + +There is a mapping between indices and GPIO connection IDs as follows + id index 0 + vbus index 1 + mux index 2 diff --git a/Documentation/filesystems/Locking b/Documentation/filesystems/Locking index fdcfdd79682a..fe25787ff6d4 100644 --- a/Documentation/filesystems/Locking +++ b/Documentation/filesystems/Locking @@ -58,8 +58,7 @@ prototypes: int (*permission) (struct inode *, int, unsigned int); int (*get_acl)(struct inode *, int); int (*setattr) (struct dentry *, struct iattr *); - int (*getattr) (const struct path *, struct dentry *, struct kstat *, - u32, unsigned int); + int (*getattr) (const struct path *, struct kstat *, u32, unsigned int); ssize_t (*listxattr) (struct dentry *, char *, size_t); int (*fiemap)(struct inode *, struct fiemap_extent_info *, u64 start, u64 len); void (*update_time)(struct inode *, struct timespec *, int); diff --git a/Documentation/filesystems/porting b/Documentation/filesystems/porting index 95280079c0b3..5fb17f49f7a2 100644 --- a/Documentation/filesystems/porting +++ b/Documentation/filesystems/porting @@ -600,3 +600,9 @@ in your dentry operations instead. [recommended] ->readlink is optional for symlinks. Don't set, unless filesystem needs to fake something for readlink(2). +-- +[mandatory] + ->getattr() is now passed a struct path rather than a vfsmount and + dentry separately, and it now has request_mask and query_flags arguments + to specify the fields and sync type requested by statx. Filesystems not + supporting any statx-specific features may ignore the new arguments. diff --git a/Documentation/filesystems/vfs.txt b/Documentation/filesystems/vfs.txt index 569211703721..94dd27ef4a76 100644 --- a/Documentation/filesystems/vfs.txt +++ b/Documentation/filesystems/vfs.txt @@ -382,8 +382,7 @@ struct inode_operations { int (*permission) (struct inode *, int); int (*get_acl)(struct inode *, int); int (*setattr) (struct dentry *, struct iattr *); - int (*getattr) (const struct path *, struct dentry *, struct kstat *, - u32, unsigned int); + int (*getattr) (const struct path *, struct kstat *, u32, unsigned int); ssize_t (*listxattr) (struct dentry *, char *, size_t); void (*update_time)(struct inode *, struct timespec *, int); int (*atomic_open)(struct inode *, struct dentry *, struct file *, diff --git a/Documentation/gcc-plugins.txt b/Documentation/gcc-plugins.txt index 891c69464434..433eaefb4aa1 100644 --- a/Documentation/gcc-plugins.txt +++ b/Documentation/gcc-plugins.txt @@ -18,8 +18,8 @@ because gcc versions 4.5 and 4.6 are compiled by a C compiler, gcc-4.7 can be compiled by a C or a C++ compiler, and versions 4.8+ can only be compiled by a C++ compiler. -Currently the GCC plugin infrastructure supports only the x86, arm and arm64 -architectures. +Currently the GCC plugin infrastructure supports only the x86, arm, arm64 and +powerpc architectures. This infrastructure was ported from grsecurity [6] and PaX [7]. diff --git a/Documentation/networking/i40e.txt b/Documentation/networking/i40e.txt index a251bf4fe9c9..57e616ed10b0 100644 --- a/Documentation/networking/i40e.txt +++ b/Documentation/networking/i40e.txt @@ -63,6 +63,78 @@ Additional Configurations The latest release of ethtool can be found from https://www.kernel.org/pub/software/network/ethtool + + Flow Director n-ntuple traffic filters (FDir) + --------------------------------------------- + The driver utilizes the ethtool interface for configuring ntuple filters, + via "ethtool -N <device> <filter>". + + The sctp4, ip4, udp4, and tcp4 flow types are supported with the standard + fields including src-ip, dst-ip, src-port and dst-port. The driver only + supports fully enabling or fully masking the fields, so use of the mask + fields for partial matches is not supported. + + Additionally, the driver supports using the action to specify filters for a + Virtual Function. You can specify the action as a 64bit value, where the + lower 32 bits represents the queue number, while the next 8 bits represent + which VF. Note that 0 is the PF, so the VF identifier is offset by 1. For + example: + + ... action 0x800000002 ... + + Would indicate to direct traffic for Virtual Function 7 (8 minus 1) on queue + 2 of that VF. + + The driver also supports using the user-defined field to specify 2 bytes of + arbitrary data to match within the packet payload in addition to the regular + fields. The data is specified in the lower 32bits of the user-def field in + the following way: + + +----------------------------+---------------------------+ + | 31 28 24 20 16 | 15 12 8 4 0| + +----------------------------+---------------------------+ + | offset into packet payload | 2 bytes of flexible data | + +----------------------------+---------------------------+ + + As an example, + + ... user-def 0x4FFFF .... + + means to match the value 0xFFFF 4 bytes into the packet payload. Note that + the offset is based on the beginning of the payload, and not the beginning + of the packet. Thus + + flow-type tcp4 ... user-def 0x8BEAF .... + + would match TCP/IPv4 packets which have the value 0xBEAF 8bytes into the + TCP/IPv4 payload. + + For ICMP, the hardware parses the ICMP header as 4 bytes of header and 4 + bytes of payload, so if you want to match an ICMP frames payload you may need + to add 4 to the offset in order to match the data. + + Furthermore, the offset can only be up to a value of 64, as the hardware + will only read up to 64 bytes of data from the payload. It must also be even + as the flexible data is 2 bytes long and must be aligned to byte 0 of the + packet payload. + + When programming filters, the hardware is limited to using a single input + set for each flow type. This means that it is an error to program two + different filters with the same type that don't match on the same fields. + Thus the second of the following two commands will fail: + + ethtool -N <device> flow-type tcp4 src-ip 192.168.0.7 action 5 + ethtool -N <device> flow-type tcp4 dst-ip 192.168.15.18 action 1 + + This is because the first filter will be accepted and reprogram the input + set for TCPv4 filters, but the second filter will be unable to reprogram the + input set until all the conflicting TCPv4 filters are first removed. + + Note that the user-defined flexible offset is also considered part of the + input set and cannot be programmed separately for multiple filters of the + same type. However, the flexible data is not part of the input set and + multiple filters may use the same offset but match against different data. + Data Center Bridging (DCB) -------------------------- DCB configuration is not currently supported. diff --git a/Documentation/networking/ip-sysctl.txt b/Documentation/networking/ip-sysctl.txt index fc73eeb7b3b8..b1c6500e7a8d 100644 --- a/Documentation/networking/ip-sysctl.txt +++ b/Documentation/networking/ip-sysctl.txt @@ -73,6 +73,14 @@ fib_multipath_use_neigh - BOOLEAN 0 - disabled 1 - enabled +fib_multipath_hash_policy - INTEGER + Controls which hash policy to use for multipath routes. Only valid + for kernels built with CONFIG_IP_ROUTE_MULTIPATH enabled. + Default: 0 (Layer 3) + Possible values: + 0 - Layer 3 + 1 - Layer 4 + route/max_size - INTEGER Maximum number of routes allowed in the kernel. Increase this when using large numbers of interfaces and/or routes. @@ -640,11 +648,6 @@ tcp_tso_win_divisor - INTEGER building larger TSO frames. Default: 3 -tcp_tw_recycle - BOOLEAN - Enable fast recycling TIME-WAIT sockets. Default value is 0. - It should not be changed without advice/request of technical - experts. - tcp_tw_reuse - BOOLEAN Allow to reuse TIME-WAIT sockets for new connections when it is safe from protocol viewpoint. Default value is 0. @@ -853,12 +856,21 @@ ip_dynaddr - BOOLEAN ip_early_demux - BOOLEAN Optimize input packet processing down to one demux for certain kinds of local sockets. Currently we only do this - for established TCP sockets. + for established TCP and connected UDP sockets. It may add an additional cost for pure routing workloads that reduces overall throughput, in such case you should disable it. Default: 1 +tcp_early_demux - BOOLEAN + Enable early demux for established TCP sockets. + Default: 1 + +udp_early_demux - BOOLEAN + Enable early demux for connected UDP sockets. Disable this if + your system could experience more unconnected load. + Default: 1 + icmp_echo_ignore_all - BOOLEAN If set non-zero, then the kernel will ignore all ICMP ECHO requests sent to it. @@ -1006,7 +1018,8 @@ accept_redirects - BOOLEAN FALSE (router) forwarding - BOOLEAN - Enable IP forwarding on this interface. + Enable IP forwarding on this interface. This controls whether packets + received _on_ this interface can be forwarded. mc_forwarding - BOOLEAN Do multicast routing. The kernel needs to be compiled with CONFIG_MROUTE @@ -1457,11 +1470,20 @@ accept_ra_pinfo - BOOLEAN Functional default: enabled if accept_ra is enabled. disabled if accept_ra is disabled. +accept_ra_rt_info_min_plen - INTEGER + Minimum prefix length of Route Information in RA. + + Route Information w/ prefix smaller than this variable shall + be ignored. + + Functional default: 0 if accept_ra_rtr_pref is enabled. + -1 if accept_ra_rtr_pref is disabled. + accept_ra_rt_info_max_plen - INTEGER Maximum prefix length of Route Information in RA. - Route Information w/ prefix larger than or equal to this - variable shall be ignored. + Route Information w/ prefix larger than this variable shall + be ignored. Functional default: 0 if accept_ra_rtr_pref is enabled. -1 if accept_ra_rtr_pref is disabled. diff --git a/Documentation/networking/ipvs-sysctl.txt b/Documentation/networking/ipvs-sysctl.txt index e6b1c025fdd8..056898685d40 100644 --- a/Documentation/networking/ipvs-sysctl.txt +++ b/Documentation/networking/ipvs-sysctl.txt @@ -175,6 +175,14 @@ nat_icmp_send - BOOLEAN for VS/NAT when the load balancer receives packets from real servers but the connection entries don't exist. +pmtu_disc - BOOLEAN + 0 - disabled + not 0 - enabled (default) + + By default, reject with FRAG_NEEDED all DF packets that exceed + the PMTU, irrespective of the forwarding method. For TUN method + the flag can be disabled to fragment such packets. + secure_tcp - INTEGER 0 - disabled (default) @@ -185,15 +193,59 @@ secure_tcp - INTEGER The value definition is the same as that of drop_entry and drop_packet. -sync_threshold - INTEGER - default 3 +sync_threshold - vector of 2 INTEGERs: sync_threshold, sync_period + default 3 50 + + It sets synchronization threshold, which is the minimum number + of incoming packets that a connection needs to receive before + the connection will be synchronized. A connection will be + synchronized, every time the number of its incoming packets + modulus sync_period equals the threshold. The range of the + threshold is from 0 to sync_period. + + When sync_period and sync_refresh_period are 0, send sync only + for state changes or only once when pkts matches sync_threshold + +sync_refresh_period - UNSIGNED INTEGER + default 0 + + In seconds, difference in reported connection timer that triggers + new sync message. It can be used to avoid sync messages for the + specified period (or half of the connection timeout if it is lower) + if connection state is not changed since last sync. + + This is useful for normal connections with high traffic to reduce + sync rate. Additionally, retry sync_retries times with period of + sync_refresh_period/8. + +sync_retries - INTEGER + default 0 + + Defines sync retries with period of sync_refresh_period/8. Useful + to protect against loss of sync messages. The range of the + sync_retries is from 0 to 3. + +sync_qlen_max - UNSIGNED LONG + + Hard limit for queued sync messages that are not sent yet. It + defaults to 1/32 of the memory pages but actually represents + number of messages. It will protect us from allocating large + parts of memory when the sending rate is lower than the queuing + rate. + +sync_sock_size - INTEGER + default 0 + + Configuration of SNDBUF (master) or RCVBUF (slave) socket limit. + Default value is 0 (preserve system defaults). + +sync_ports - INTEGER + default 1 - It sets synchronization threshold, which is the minimum number - of incoming packets that a connection needs to receive before - the connection will be synchronized. A connection will be - synchronized, every time the number of its incoming packets - modulus 50 equals the threshold. The range of the threshold is - from 0 to 49. + The number of threads that master and backup servers can use for + sync traffic. Every thread will use single UDP port, thread 0 will + use the default port 8848 while last thread will use port + 8848+sync_ports-1. snat_reroute - BOOLEAN 0 - disabled diff --git a/Documentation/networking/mpls-sysctl.txt b/Documentation/networking/mpls-sysctl.txt index 15d8d16934fd..2f24a1912a48 100644 --- a/Documentation/networking/mpls-sysctl.txt +++ b/Documentation/networking/mpls-sysctl.txt @@ -19,6 +19,25 @@ platform_labels - INTEGER Possible values: 0 - 1048575 Default: 0 +ip_ttl_propagate - BOOL + Control whether TTL is propagated from the IPv4/IPv6 header to + the MPLS header on imposing labels and propagated from the + MPLS header to the IPv4/IPv6 header on popping the last label. + + If disabled, the MPLS transport network will appear as a + single hop to transit traffic. + + 0 - disabled / RFC 3443 [Short] Pipe Model + 1 - enabled / RFC 3443 Uniform Model (default) + +default_ttl - BOOL + Default TTL value to use for MPLS packets where it cannot be + propagated from an IP header, either because one isn't present + or ip_ttl_propagate has been disabled. + + Possible values: 1 - 255 + Default: 255 + conf/<interface>/input - BOOL Control whether packets can be input on this interface. diff --git a/Documentation/pinctrl.txt b/Documentation/pinctrl.txt index 54bd5faa8782..f2af35f6d6b2 100644 --- a/Documentation/pinctrl.txt +++ b/Documentation/pinctrl.txt @@ -77,9 +77,15 @@ static struct pinctrl_desc foo_desc = { int __init foo_probe(void) { + int error; + struct pinctrl_dev *pctl; - return pinctrl_register_and_init(&foo_desc, <PARENT>, NULL, &pctl); + error = pinctrl_register_and_init(&foo_desc, <PARENT>, NULL, &pctl); + if (error) + return error; + + return pinctrl_enable(pctl); } To enable the pinctrl subsystem and the subgroups for PINMUX and PINCONF and diff --git a/Documentation/process/stable-kernel-rules.rst b/Documentation/process/stable-kernel-rules.rst index 11ec2d93a5e0..61e9c78bd6d1 100644 --- a/Documentation/process/stable-kernel-rules.rst +++ b/Documentation/process/stable-kernel-rules.rst @@ -124,7 +124,7 @@ specified in the following format in the sign-off area: .. code-block:: none - Cc: <stable@vger.kernel.org> # 3.3.x- + Cc: <stable@vger.kernel.org> # 3.3.x The tag has the meaning of: diff --git a/Documentation/trace/kprobetrace.txt b/Documentation/trace/kprobetrace.txt index e4991fb1eedc..41ef9d8efe95 100644 --- a/Documentation/trace/kprobetrace.txt +++ b/Documentation/trace/kprobetrace.txt @@ -12,7 +12,7 @@ kprobes can probe (this means, all functions body except for __kprobes functions). Unlike the Tracepoint based event, this can be added and removed dynamically, on the fly. -To enable this feature, build your kernel with CONFIG_KPROBE_EVENT=y. +To enable this feature, build your kernel with CONFIG_KPROBE_EVENTS=y. Similar to the events tracer, this doesn't need to be activated via current_tracer. Instead of that, add probe points via diff --git a/Documentation/trace/uprobetracer.txt b/Documentation/trace/uprobetracer.txt index fa7b680ee8a0..bf526a7c5559 100644 --- a/Documentation/trace/uprobetracer.txt +++ b/Documentation/trace/uprobetracer.txt @@ -7,7 +7,7 @@ Overview -------- Uprobe based trace events are similar to kprobe based trace events. -To enable this feature, build your kernel with CONFIG_UPROBE_EVENT=y. +To enable this feature, build your kernel with CONFIG_UPROBE_EVENTS=y. Similar to the kprobe-event tracer, this doesn't need to be activated via current_tracer. Instead of that, add probe points via diff --git a/Documentation/virtual/kvm/api.txt b/Documentation/virtual/kvm/api.txt index 069450938b79..fd106899afd1 100644 --- a/Documentation/virtual/kvm/api.txt +++ b/Documentation/virtual/kvm/api.txt @@ -951,6 +951,10 @@ This ioctl allows the user to create or modify a guest physical memory slot. When changing an existing slot, it may be moved in the guest physical memory space, or its flags may be modified. It may not be resized. Slots may not overlap in guest physical address space. +Bits 0-15 of "slot" specifies the slot id and this value should be +less than the maximum number of user memory slots supported per VM. +The maximum allowed slots can be queried using KVM_CAP_NR_MEMSLOTS, +if this capability is supported by the architecture. If KVM_CAP_MULTI_ADDRESS_SPACE is available, bits 16-31 of "slot" specifies the address space which is being modified. They must be @@ -3373,6 +3377,69 @@ struct kvm_ppc_resize_hpt { __u32 pad; }; +4.104 KVM_X86_GET_MCE_CAP_SUPPORTED + +Capability: KVM_CAP_MCE +Architectures: x86 +Type: system ioctl +Parameters: u64 mce_cap (out) +Returns: 0 on success, -1 on error + +Returns supported MCE capabilities. The u64 mce_cap parameter +has the same format as the MSR_IA32_MCG_CAP register. Supported +capabilities will have the corresponding bits set. + +4.105 KVM_X86_SETUP_MCE + +Capability: KVM_CAP_MCE +Architectures: x86 +Type: vcpu ioctl +Parameters: u64 mcg_cap (in) +Returns: 0 on success, + -EFAULT if u64 mcg_cap cannot be read, + -EINVAL if the requested number of banks is invalid, + -EINVAL if requested MCE capability is not supported. + +Initializes MCE support for use. The u64 mcg_cap parameter +has the same format as the MSR_IA32_MCG_CAP register and +specifies which capabilities should be enabled. The maximum +supported number of error-reporting banks can be retrieved when +checking for KVM_CAP_MCE. The supported capabilities can be +retrieved with KVM_X86_GET_MCE_CAP_SUPPORTED. + +4.106 KVM_X86_SET_MCE + +Capability: KVM_CAP_MCE +Architectures: x86 +Type: vcpu ioctl +Parameters: struct kvm_x86_mce (in) +Returns: 0 on success, + -EFAULT if struct kvm_x86_mce cannot be read, + -EINVAL if the bank number is invalid, + -EINVAL if VAL bit is not set in status field. + +Inject a machine check error (MCE) into the guest. The input +parameter is: + +struct kvm_x86_mce { + __u64 status; + __u64 addr; + __u64 misc; + __u64 mcg_status; + __u8 bank; + __u8 pad1[7]; + __u64 pad2[3]; +}; + +If the MCE being reported is an uncorrected error, KVM will +inject it as an MCE exception into the guest. If the guest +MCG_STATUS register reports that an MCE is in progress, KVM +causes an KVM_EXIT_SHUTDOWN vmexit. + +Otherwise, if the MCE is a corrected error, KVM will just +store it in the corresponding bank (provided this bank is +not holding a previously reported uncorrected error). + 5. The kvm_run structure ------------------------ diff --git a/Documentation/virtual/kvm/devices/arm-vgic.txt b/Documentation/virtual/kvm/devices/arm-vgic.txt index 76e61c883347..b2f60ca8b60c 100644 --- a/Documentation/virtual/kvm/devices/arm-vgic.txt +++ b/Documentation/virtual/kvm/devices/arm-vgic.txt @@ -83,6 +83,12 @@ Groups: Bits for undefined preemption levels are RAZ/WI. + For historical reasons and to provide ABI compatibility with userspace we + export the GICC_PMR register in the format of the GICH_VMCR.VMPriMask + field in the lower 5 bits of a word, meaning that userspace must always + use the lower 5 bits to communicate with the KVM device and must shift the + value left by 3 places to obtain the actual priority mask level. + Limitations: - Priorities are not implemented, and registers are RAZ/WI - Currently only implemented for KVM_DEV_TYPE_ARM_VGIC_V2. diff --git a/Documentation/vm/userfaultfd.txt b/Documentation/vm/userfaultfd.txt index 0e5543a920e5..bb2f945f87ab 100644 --- a/Documentation/vm/userfaultfd.txt +++ b/Documentation/vm/userfaultfd.txt @@ -172,10 +172,6 @@ the same read(2) protocol as for the page fault notifications. The manager has to explicitly enable these events by setting appropriate bits in uffdio_api.features passed to UFFDIO_API ioctl: -UFFD_FEATURE_EVENT_EXIT - enable notification about exit() of the -non-cooperative process. When the monitored process exits, the uffd -manager will get UFFD_EVENT_EXIT. - UFFD_FEATURE_EVENT_FORK - enable userfaultfd hooks for fork(). When this feature is enabled, the userfaultfd context of the parent process is duplicated into the newly created process. The manager receives |