diff options
Diffstat (limited to 'arch/arm/boot/dts/omap3-overo-base.dtsi')
| -rw-r--r-- | arch/arm/boot/dts/omap3-overo-base.dtsi | 44 |
1 files changed, 44 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/omap3-overo-base.dtsi b/arch/arm/boot/dts/omap3-overo-base.dtsi index edac70e9204c..13d1ad215494 100644 --- a/arch/arm/boot/dts/omap3-overo-base.dtsi +++ b/arch/arm/boot/dts/omap3-overo-base.dtsi @@ -30,6 +30,24 @@ ti,codec = <&twl_audio>; }; + /* HS USB Port 2 Power */ + hsusb2_power: hsusb2_power_reg { + compatible = "regulator-fixed"; + regulator-name = "hsusb2_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio6 8 0>; /* gpio_168: vbus enable */ + startup-delay-us = <70000>; + enable-active-high; + }; + + /* HS USB Host PHY on PORT 2 */ + hsusb2_phy: hsusb2_phy { + compatible = "usb-nop-xceiv"; + reset-gpios = <&gpio6 23 GPIO_ACTIVE_LOW>; /* gpio_183 */ + vcc-supply = <&hsusb2_power>; + }; + /* Regulator to trigger the nPoweron signal of the Wifi module */ w3cbw003c_npoweron: regulator-w3cbw003c-npoweron { compatible = "regulator-fixed"; @@ -64,6 +82,11 @@ }; &omap3_pmx_core { + pinctrl-names = "default"; + pinctrl-0 = < + &hsusb2_pins + >; + uart2_pins: pinmux_uart2_pins { pinctrl-single,pins = < OMAP3_CORE1_IOPAD(0x216c, PIN_INPUT | MUX_MODE1) /* mcbsp3_dx.uart2_cts */ @@ -116,6 +139,19 @@ OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE4) /* uart3_rts_sd.gpio_164 */ >; }; + + hsusb2_pins: pinmux_hsusb2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */ + OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */ + OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */ + OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */ + OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */ + OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */ + OMAP3_CORE1_IOPAD(0x21be, PIN_OUTPUT | MUX_MODE4) /* i2c2_scl.gpio_168 */ + OMAP3_CORE1_IOPAD(0x21c0, PIN_OUTPUT | MUX_MODE4) /* i2c2_sda.gpio_183 */ + >; + }; }; &i2c1 { @@ -177,6 +213,14 @@ power = <50>; }; +&usbhshost { + port2-mode = "ehci-phy"; +}; + +&usbhsehci { + phys = <0 &hsusb2_phy>; +}; + &uart2 { pinctrl-names = "default"; pinctrl-0 = <&uart2_pins>; |