diff options
Diffstat (limited to 'arch/arm/boot/dts/omap5-uevm.dts')
| -rw-r--r-- | arch/arm/boot/dts/omap5-uevm.dts | 84 |
1 files changed, 38 insertions, 46 deletions
diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts index 65d7b601651c..002fa70180a5 100644 --- a/arch/arm/boot/dts/omap5-uevm.dts +++ b/arch/arm/boot/dts/omap5-uevm.dts @@ -27,21 +27,10 @@ regulator-max-microvolt = <3000000>; }; - /* HS USB Port 2 RESET */ - hsusb2_reset: hsusb2_reset_reg { - compatible = "regulator-fixed"; - regulator-name = "hsusb2_reset"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&gpio3 16 GPIO_ACTIVE_HIGH>; /* gpio3_80 HUB_NRESET */ - startup-delay-us = <70000>; - enable-active-high; - }; - /* HS USB Host PHY on PORT 2 */ hsusb2_phy: hsusb2_phy { compatible = "usb-nop-xceiv"; - reset-supply = <&hsusb2_reset>; + reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */ /** * FIXME * Put the right clock phandle here when available @@ -51,21 +40,10 @@ clock-frequency = <19200000>; }; - /* HS USB Port 3 RESET */ - hsusb3_reset: hsusb3_reset_reg { - compatible = "regulator-fixed"; - regulator-name = "hsusb3_reset"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>; /* gpio3_79 ETH_NRESET */ - startup-delay-us = <70000>; - enable-active-high; - }; - /* HS USB Host PHY on PORT 3 */ hsusb3_phy: hsusb3_phy { compatible = "usb-nop-xceiv"; - reset-supply = <&hsusb3_reset>; + reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; /* gpio3_79 ETH_NRESET */ }; leds { @@ -84,7 +62,6 @@ pinctrl-0 = < &twl6040_pins &mcpdm_pins - &dmic_pins &mcbsp1_pins &mcbsp2_pins &usbhost_pins @@ -93,7 +70,7 @@ twl6040_pins: pinmux_twl6040_pins { pinctrl-single,pins = < - 0x18a (PIN_OUTPUT | MUX_MODE6) /* perslimbus2_clock.gpio5_145 */ + 0x17e (PIN_OUTPUT | MUX_MODE6) /* mcspi1_somi.gpio5_141 */ >; }; @@ -107,15 +84,6 @@ >; }; - dmic_pins: pinmux_dmic_pins { - pinctrl-single,pins = < - 0x144 (PIN_INPUT | MUX_MODE0) /* abedmic_din1.abedmic_din1 */ - 0x146 (PIN_INPUT | MUX_MODE0) /* abedmic_din2.abedmic_din2 */ - 0x148 (PIN_INPUT | MUX_MODE0) /* abedmic_din3.abedmic_din3 */ - 0x14a (PIN_OUTPUT | MUX_MODE0) /* abedmic_clk1.abedmic_clk1 */ - >; - }; - mcbsp1_pins: pinmux_mcbsp1_pins { pinctrl-single,pins = < 0x14c (PIN_INPUT | MUX_MODE1) /* abedmic_clk2.abemcbsp1_fsx */ @@ -153,25 +121,25 @@ 0xbc (PIN_INPUT | MUX_MODE0) /* mcspi2_clk */ 0xbe (PIN_INPUT | MUX_MODE0) /* mcspi2_simo */ 0xc0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi2_somi */ - 0xc2 (PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs */ + 0xc2 (PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs0 */ >; }; mcspi3_pins: pinmux_mcspi3_pins { pinctrl-single,pins = < - 0x78 (PIN_INPUT | MUX_MODE1) /* mcspi2_somi */ - 0x7a (PIN_INPUT | MUX_MODE1) /* mcspi2_cs */ - 0x7c (PIN_INPUT | MUX_MODE1) /* mcspi2_simo */ - 0x7e (PIN_INPUT | MUX_MODE1) /* mcspi2_clk */ + 0x78 (PIN_INPUT | MUX_MODE1) /* mcspi3_somi */ + 0x7a (PIN_INPUT | MUX_MODE1) /* mcspi3_cs0 */ + 0x7c (PIN_INPUT | MUX_MODE1) /* mcspi3_simo */ + 0x7e (PIN_INPUT | MUX_MODE1) /* mcspi3_clk */ >; }; mcspi4_pins: pinmux_mcspi4_pins { pinctrl-single,pins = < - 0x164 (PIN_INPUT | MUX_MODE1) /* mcspi2_clk */ - 0x168 (PIN_INPUT | MUX_MODE1) /* mcspi2_simo */ - 0x16a (PIN_INPUT | MUX_MODE1) /* mcspi2_somi */ - 0x16c (PIN_INPUT | MUX_MODE1) /* mcspi2_cs */ + 0x164 (PIN_INPUT | MUX_MODE1) /* mcspi4_clk */ + 0x168 (PIN_INPUT | MUX_MODE1) /* mcspi4_simo */ + 0x16a (PIN_INPUT | MUX_MODE1) /* mcspi4_somi */ + 0x16c (PIN_INPUT | MUX_MODE1) /* mcspi4_cs0 */ >; }; @@ -271,6 +239,14 @@ reg = <0x48>; interrupt-controller; #interrupt-cells = <2>; + ti,system-power-controller; + + extcon_usb3: palmas_usb { + compatible = "ti,palmas-usb-vid"; + ti,enable-vbus-detection; + ti,enable-id-detection; + ti,wakeup; + }; palmas_pmic { compatible = "ti,palmas-pmic"; @@ -334,15 +310,22 @@ ti,smps-range = <0x80>; }; - smps10_reg: smps10 { + smps10_out2_reg: smps10_out2 { /* VBUS_5V_OTG */ - regulator-name = "smps10"; + regulator-name = "smps10_out2"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; regulator-always-on; regulator-boot-on; }; + smps10_out1_reg: smps10_out1 { + /* VBUS_5V_OTG */ + regulator-name = "smps10_out1"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + ldo1_reg: ldo1 { /* VDDAPHY_CAM: vdda_csiport */ regulator-name = "ldo1"; @@ -470,6 +453,11 @@ phys = <0 &hsusb2_phy &hsusb3_phy>; }; +&usb3 { + extcon = <&extcon_usb3>; + vbus-supply = <&smps10_out1_reg>; +}; + &mcspi1 { }; @@ -503,3 +491,7 @@ pinctrl-names = "default"; pinctrl-0 = <&uart5_pins>; }; + +&cpu0 { + cpu0-supply = <&smps123_reg>; +}; |