diff options
Diffstat (limited to 'arch/arm/mach-at91/include/mach/board.h')
| -rw-r--r-- | arch/arm/mach-at91/include/mach/board.h | 55 |
1 files changed, 0 insertions, 55 deletions
diff --git a/arch/arm/mach-at91/include/mach/board.h b/arch/arm/mach-at91/include/mach/board.h index c55a4364ffb4..662451d85fc9 100644 --- a/arch/arm/mach-at91/include/mach/board.h +++ b/arch/arm/mach-at91/include/mach/board.h @@ -31,42 +31,15 @@ #ifndef __ASM_ARCH_BOARD_H #define __ASM_ARCH_BOARD_H -#include <linux/mtd/partitions.h> -#include <linux/device.h> -#include <linux/i2c.h> -#include <linux/leds.h> -#include <linux/spi/spi.h> -#include <linux/usb/atmel_usba_udc.h> -#include <linux/atmel-mci.h> -#include <sound/atmel-ac97c.h> -#include <linux/serial.h> -#include <linux/platform_data/macb.h> #include <linux/platform_data/atmel.h> /* USB Device */ -struct at91_udc_data { - int vbus_pin; /* high == host powering us */ - u8 vbus_active_low; /* vbus polarity */ - u8 vbus_polled; /* Use polling, not interrupt */ - int pullup_pin; /* active == D+ pulled up */ - u8 pullup_active_low; /* true == pullup_pin is active low */ -}; extern void __init at91_add_device_udc(struct at91_udc_data *data); /* USB High Speed Device */ extern void __init at91_add_device_usba(struct usba_platform_data *data); /* Compact Flash */ -struct at91_cf_data { - int irq_pin; /* I/O IRQ */ - int det_pin; /* Card detect */ - int vcc_pin; /* power switching */ - int rst_pin; /* card reset */ - u8 chipselect; /* EBI Chip Select number */ - u8 flags; -#define AT91_CF_TRUE_IDE 0x01 -#define AT91_IDE_SWAP_A0_A2 0x02 -}; extern void __init at91_add_device_cf(struct at91_cf_data *data); /* MMC / SD */ @@ -86,16 +59,6 @@ extern void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *d extern void __init at91_add_device_eth(struct macb_platform_data *data); /* USB Host */ -#define AT91_MAX_USBH_PORTS 3 -struct at91_usbh_data { - int vbus_pin[AT91_MAX_USBH_PORTS]; /* port power-control pin */ - int overcurrent_pin[AT91_MAX_USBH_PORTS]; - u8 ports; /* number of ports on root hub */ - u8 overcurrent_supported; - u8 vbus_pin_active_low[AT91_MAX_USBH_PORTS]; - u8 overcurrent_status[AT91_MAX_USBH_PORTS]; - u8 overcurrent_changed[AT91_MAX_USBH_PORTS]; -}; extern void __init at91_add_device_usbh(struct at91_usbh_data *data); extern void __init at91_add_device_usbh_ohci(struct at91_usbh_data *data); extern void __init at91_add_device_usbh_ehci(struct at91_usbh_data *data); @@ -124,13 +87,6 @@ extern void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pin extern struct platform_device *atmel_default_console_device; -struct atmel_uart_data { - int num; /* port num */ - short use_dma_tx; /* use transmit DMA? */ - short use_dma_rx; /* use receive DMA? */ - void __iomem *regs; /* virt. base address, if any */ - struct serial_rs485 rs485; /* rs485 settings */ -}; extern void __init at91_add_device_serial(void); /* @@ -173,24 +129,13 @@ extern void __init at91_add_device_isi(struct isi_platform_data *data, bool use_pck_as_mck); /* Touchscreen Controller */ -struct at91_tsadcc_data { - unsigned int adc_clock; - u8 pendet_debounce; - u8 ts_sample_hold_time; -}; extern void __init at91_add_device_tsadcc(struct at91_tsadcc_data *data); /* CAN */ -struct at91_can_data { - void (*transceiver_switch)(int on); -}; extern void __init at91_add_device_can(struct at91_can_data *data); /* LEDs */ extern void __init at91_gpio_leds(struct gpio_led *leds, int nr); extern void __init at91_pwm_leds(struct gpio_led *leds, int nr); -/* FIXME: this needs a better location, but gets stuff building again */ -extern int at91_suspend_entering_slow_clock(void); - #endif |