1 files changed, 82 insertions, 0 deletions
diff --git a/arch/arm/mach-cns3xxx/include/mach/entry-macro.S b/arch/arm/mach-cns3xxx/include/mach/entry-macro.S
new file mode 100644
index 000000000000..5e1c5545680f
--- /dev/null
+++ b/arch/arm/mach-cns3xxx/include/mach/entry-macro.S
@@ -0,0 +1,82 @@
+/*
+ * Low-level IRQ helper macros for Cavium Networks platforms
+ *
+ * Copyright 2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ */
+
+#include <mach/hardware.h>
+#include <asm/hardware/gic.h>
+
+		.macro	disable_fiq
+		.endm
+
+		.macro  get_irqnr_preamble, base, tmp
+		ldr	\base, =gic_cpu_base_addr
+		ldr	\base, [\base]
+		.endm
+
+		.macro  arch_ret_to_user, tmp1, tmp2
+		.endm
+
+		/*
+		 * The interrupt numbering scheme is defined in the
+		 * interrupt controller spec.  To wit:
+		 *
+		 * Interrupts 0-15 are IPI
+		 * 16-28 are reserved
+		 * 29-31 are local.  We allow 30 to be used for the watchdog.
+		 * 32-1020 are global
+		 * 1021-1022 are reserved
+		 * 1023 is "spurious" (no interrupt)
+		 *
+		 * For now, we ignore all local interrupts so only return an interrupt if it's
+		 * between 30 and 1020.  The test_for_ipi routine below will pick up on IPIs.
+		 *
+		 * A simple read from the controller will tell us the number of the highest
+                 * priority enabled interrupt.  We then just need to check whether it is in the
+		 * valid range for an IRQ (30-1020 inclusive).
+		 */
+
+		.macro  get_irqnr_and_base, irqnr, irqstat, base, tmp
+
+		ldr     \irqstat, [\base, #GIC_CPU_INTACK] /* bits 12-10 = src CPU, 9-0 = int # */
+
+		ldr	\tmp, =1021
+
+		bic     \irqnr, \irqstat, #0x1c00
+
+		cmp     \irqnr, #29
+		cmpcc	\irqnr, \irqnr
+		cmpne	\irqnr, \tmp
+		cmpcs	\irqnr, \irqnr
+
+		.endm
+
+		/* We assume that irqstat (the raw value of the IRQ acknowledge
+		 * register) is preserved from the macro above.
+		 * If there is an IPI, we immediately signal end of interrupt on the
+		 * controller, since this requires the original irqstat value which
+		 * we won't easily be able to recreate later.
+		 */
+
+		.macro test_for_ipi, irqnr, irqstat, base, tmp
+		bic	\irqnr, \irqstat, #0x1c00
+		cmp	\irqnr, #16
+		strcc	\irqstat, [\base, #GIC_CPU_EOI]
+		cmpcs	\irqnr, \irqnr
+		.endm
+
+		/* As above, this assumes that irqstat and base are preserved.. */
+
+		.macro test_for_ltirq, irqnr, irqstat, base, tmp
+		bic	\irqnr, \irqstat, #0x1c00
+		mov 	\tmp, #0
+		cmp	\irqnr, #29
+		moveq	\tmp, #1
+		streq	\irqstat, [\base, #GIC_CPU_EOI]
+		cmp	\tmp, #0
+		.endm