aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/atlx/atl1_hw.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/atlx/atl1_hw.c')
-rw-r--r--drivers/net/atlx/atl1_hw.c720
1 files changed, 0 insertions, 720 deletions
diff --git a/drivers/net/atlx/atl1_hw.c b/drivers/net/atlx/atl1_hw.c
deleted file mode 100644
index 9d3bd22e3a82..000000000000
--- a/drivers/net/atlx/atl1_hw.c
+++ /dev/null
@@ -1,720 +0,0 @@
-/*
- * Copyright(c) 2005 - 2006 Attansic Corporation. All rights reserved.
- * Copyright(c) 2006 Chris Snook <csnook@redhat.com>
- * Copyright(c) 2006 Jay Cliburn <jcliburn@gmail.com>
- *
- * Derived from Intel e1000 driver
- * Copyright(c) 1999 - 2005 Intel Corporation. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the Free
- * Software Foundation; either version 2 of the License, or (at your option)
- * any later version.
- *
- * This program is distributed in the hope that it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
- * more details.
- *
- * You should have received a copy of the GNU General Public License along with
- * this program; if not, write to the Free Software Foundation, Inc., 59
- * Temple Place - Suite 330, Boston, MA 02111-1307, USA.
- */
-
-#include <linux/types.h>
-#include <linux/pci.h>
-#include <linux/delay.h>
-#include <linux/if_vlan.h>
-#include <linux/etherdevice.h>
-#include <linux/crc32.h>
-#include <asm/byteorder.h>
-
-#include "atl1.h"
-
-/*
- * Reset the transmit and receive units; mask and clear all interrupts.
- * hw - Struct containing variables accessed by shared code
- * return : ATL1_SUCCESS or idle status (if error)
- */
-s32 atl1_reset_hw(struct atl1_hw *hw)
-{
- struct pci_dev *pdev = hw->back->pdev;
- u32 icr;
- int i;
-
- /*
- * Clear Interrupt mask to stop board from generating
- * interrupts & Clear any pending interrupt events
- */
- /*
- * iowrite32(0, hw->hw_addr + REG_IMR);
- * iowrite32(0xffffffff, hw->hw_addr + REG_ISR);
- */
-
- /*
- * Issue Soft Reset to the MAC. This will reset the chip's
- * transmit, receive, DMA. It will not effect
- * the current PCI configuration. The global reset bit is self-
- * clearing, and should clear within a microsecond.
- */
- iowrite32(MASTER_CTRL_SOFT_RST, hw->hw_addr + REG_MASTER_CTRL);
- ioread32(hw->hw_addr + REG_MASTER_CTRL);
-
- iowrite16(1, hw->hw_addr + REG_GPHY_ENABLE);
- ioread16(hw->hw_addr + REG_GPHY_ENABLE);
-
- msleep(1); /* delay about 1ms */
-
- /* Wait at least 10ms for All module to be Idle */
- for (i = 0; i < 10; i++) {
- icr = ioread32(hw->hw_addr + REG_IDLE_STATUS);
- if (!icr)
- break;
- msleep(1); /* delay 1 ms */
- cpu_relax(); /* FIXME: is this still the right way to do this? */
- }
-
- if (icr) {
- dev_dbg(&pdev->dev, "ICR = 0x%x\n", icr);
- return icr;
- }
-
- return ATL1_SUCCESS;
-}
-
-/* function about EEPROM
- *
- * check_eeprom_exist
- * return 0 if eeprom exist
- */
-static int atl1_check_eeprom_exist(struct atl1_hw *hw)
-{
- u32 value;
- value = ioread32(hw->hw_addr + REG_SPI_FLASH_CTRL);
- if (value & SPI_FLASH_CTRL_EN_VPD) {
- value &= ~SPI_FLASH_CTRL_EN_VPD;
- iowrite32(value, hw->hw_addr + REG_SPI_FLASH_CTRL);
- }
-
- value = ioread16(hw->hw_addr + REG_PCIE_CAP_LIST);
- return ((value & 0xFF00) == 0x6C00) ? 0 : 1;
-}
-
-static bool atl1_read_eeprom(struct atl1_hw *hw, u32 offset, u32 *p_value)
-{
- int i;
- u32 control;
-
- if (offset & 3)
- return false; /* address do not align */
-
- iowrite32(0, hw->hw_addr + REG_VPD_DATA);
- control = (offset & VPD_CAP_VPD_ADDR_MASK) << VPD_CAP_VPD_ADDR_SHIFT;
- iowrite32(control, hw->hw_addr + REG_VPD_CAP);
- ioread32(hw->hw_addr + REG_VPD_CAP);
-
- for (i = 0; i < 10; i++) {
- msleep(2);
- control = ioread32(hw->hw_addr + REG_VPD_CAP);
- if (control & VPD_CAP_VPD_FLAG)
- break;
- }
- if (control & VPD_CAP_VPD_FLAG) {
- *p_value = ioread32(hw->hw_addr + REG_VPD_DATA);
- return true;
- }
- return false; /* timeout */
-}
-
-/*
- * Reads the value from a PHY register
- * hw - Struct containing variables accessed by shared code
- * reg_addr - address of the PHY register to read
- */
-s32 atl1_read_phy_reg(struct atl1_hw *hw, u16 reg_addr, u16 *phy_data)
-{
- u32 val;
- int i;
-
- val = ((u32) (reg_addr & MDIO_REG_ADDR_MASK)) << MDIO_REG_ADDR_SHIFT |
- MDIO_START | MDIO_SUP_PREAMBLE | MDIO_RW | MDIO_CLK_25_4 <<
- MDIO_CLK_SEL_SHIFT;
- iowrite32(val, hw->hw_addr + REG_MDIO_CTRL);
- ioread32(hw->hw_addr + REG_MDIO_CTRL);
-
- for (i = 0; i < MDIO_WAIT_TIMES; i++) {
- udelay(2);
- val = ioread32(hw->hw_addr + REG_MDIO_CTRL);
- if (!(val & (MDIO_START | MDIO_BUSY)))
- break;
- }
- if (!(val & (MDIO_START | MDIO_BUSY))) {
- *phy_data = (u16) val;
- return ATL1_SUCCESS;
- }
- return ATL1_ERR_PHY;
-}
-
-#define CUSTOM_SPI_CS_SETUP 2
-#define CUSTOM_SPI_CLK_HI 2
-#define CUSTOM_SPI_CLK_LO 2
-#define CUSTOM_SPI_CS_HOLD 2
-#define CUSTOM_SPI_CS_HI 3
-
-static bool atl1_spi_read(struct atl1_hw *hw, u32 addr, u32 *buf)
-{
- int i;
- u32 value;
-
- iowrite32(0, hw->hw_addr + REG_SPI_DATA);
- iowrite32(addr, hw->hw_addr + REG_SPI_ADDR);
-
- value = SPI_FLASH_CTRL_WAIT_READY |
- (CUSTOM_SPI_CS_SETUP & SPI_FLASH_CTRL_CS_SETUP_MASK) <<
- SPI_FLASH_CTRL_CS_SETUP_SHIFT | (CUSTOM_SPI_CLK_HI &
- SPI_FLASH_CTRL_CLK_HI_MASK) <<
- SPI_FLASH_CTRL_CLK_HI_SHIFT | (CUSTOM_SPI_CLK_LO &
- SPI_FLASH_CTRL_CLK_LO_MASK) <<
- SPI_FLASH_CTRL_CLK_LO_SHIFT | (CUSTOM_SPI_CS_HOLD &
- SPI_FLASH_CTRL_CS_HOLD_MASK) <<
- SPI_FLASH_CTRL_CS_HOLD_SHIFT | (CUSTOM_SPI_CS_HI &
- SPI_FLASH_CTRL_CS_HI_MASK) <<
- SPI_FLASH_CTRL_CS_HI_SHIFT | (1 & SPI_FLASH_CTRL_INS_MASK) <<
- SPI_FLASH_CTRL_INS_SHIFT;
-
- iowrite32(value, hw->hw_addr + REG_SPI_FLASH_CTRL);
-
- value |= SPI_FLASH_CTRL_START;
- iowrite32(value, hw->hw_addr + REG_SPI_FLASH_CTRL);
- ioread32(hw->hw_addr + REG_SPI_FLASH_CTRL);
-
- for (i = 0; i < 10; i++) {
- msleep(1); /* 1ms */
- value = ioread32(hw->hw_addr + REG_SPI_FLASH_CTRL);
- if (!(value & SPI_FLASH_CTRL_START))
- break;
- }
-
- if (value & SPI_FLASH_CTRL_START)
- return false;
-
- *buf = ioread32(hw->hw_addr + REG_SPI_DATA);
-
- return true;
-}
-
-/*
- * get_permanent_address
- * return 0 if get valid mac address,
- */
-static int atl1_get_permanent_address(struct atl1_hw *hw)
-{
- u32 addr[2];
- u32 i, control;
- u16 reg;
- u8 eth_addr[ETH_ALEN];
- bool key_valid;
-
- if (is_valid_ether_addr(hw->perm_mac_addr))
- return 0;
-
- /* init */
- addr[0] = addr[1] = 0;
-
- if (!atl1_check_eeprom_exist(hw)) { /* eeprom exist */
- reg = 0;
- key_valid = false;
- /* Read out all EEPROM content */
- i = 0;
- while (1) {
- if (atl1_read_eeprom(hw, i + 0x100, &control)) {
- if (key_valid) {
- if (reg == REG_MAC_STA_ADDR)
- addr[0] = control;
- else if (reg == (REG_MAC_STA_ADDR + 4))
- addr[1] = control;
- key_valid = false;
- } else if ((control & 0xff) == 0x5A) {
- key_valid = true;
- reg = (u16) (control >> 16);
- } else
- break; /* assume data end while encount an invalid KEYWORD */
- } else
- break; /* read error */
- i += 4;
- }
-
- *(u32 *) &eth_addr[2] = swab32(addr[0]);
- *(u16 *) &eth_addr[0] = swab16(*(u16 *) &addr[1]);
- if (is_valid_ether_addr(eth_addr)) {
- memcpy(hw->perm_mac_addr, eth_addr, ETH_ALEN);
- return 0;
- }
- return 1;
- }
-
- /* see if SPI FLAGS exist ? */
- addr[0] = addr[1] = 0;
- reg = 0;
- key_valid = false;
- i = 0;
- while (1) {
- if (atl1_spi_read(hw, i + 0x1f000, &control)) {
- if (key_valid) {
- if (reg == REG_MAC_STA_ADDR)
- addr[0] = control;
- else if (reg == (REG_MAC_STA_ADDR + 4))
- addr[1] = control;
- key_valid = false;
- } else if ((control & 0xff) == 0x5A) {
- key_valid = true;
- reg = (u16) (control >> 16);
- } else
- break; /* data end */
- } else
- break; /* read error */
- i += 4;
- }
-
- *(u32 *) &eth_addr[2] = swab32(addr[0]);
- *(u16 *) &eth_addr[0] = swab16(*(u16 *) &addr[1]);
- if (is_valid_ether_addr(eth_addr)) {
- memcpy(hw->perm_mac_addr, eth_addr, ETH_ALEN);
- return 0;
- }
-
- /*
- * On some motherboards, the MAC address is written by the
- * BIOS directly to the MAC register during POST, and is
- * not stored in eeprom. If all else thus far has failed
- * to fetch the permanent MAC address, try reading it directly.
- */
- addr[0] = ioread32(hw->hw_addr + REG_MAC_STA_ADDR);
- addr[1] = ioread16(hw->hw_addr + (REG_MAC_STA_ADDR + 4));
- *(u32 *) &eth_addr[2] = swab32(addr[0]);
- *(u16 *) &eth_addr[0] = swab16(*(u16 *) &addr[1]);
- if (is_valid_ether_addr(eth_addr)) {
- memcpy(hw->perm_mac_addr, eth_addr, ETH_ALEN);
- return 0;
- }
-
- return 1;
-}
-
-/*
- * Reads the adapter's MAC address from the EEPROM
- * hw - Struct containing variables accessed by shared code
- */
-s32 atl1_read_mac_addr(struct atl1_hw *hw)
-{
- u16 i;
-
- if (atl1_get_permanent_address(hw))
- random_ether_addr(hw->perm_mac_addr);
-
- for (i = 0; i < ETH_ALEN; i++)
- hw->mac_addr[i] = hw->perm_mac_addr[i];
- return ATL1_SUCCESS;
-}
-
-/*
- * Hashes an address to determine its location in the multicast table
- * hw - Struct containing variables accessed by shared code
- * mc_addr - the multicast address to hash
- *
- * atl1_hash_mc_addr
- * purpose
- * set hash value for a multicast address
- * hash calcu processing :
- * 1. calcu 32bit CRC for multicast address
- * 2. reverse crc with MSB to LSB
- */
-u32 atl1_hash_mc_addr(struct atl1_hw *hw, u8 *mc_addr)
-{
- u32 crc32, value = 0;
- int i;
-
- crc32 = ether_crc_le(6, mc_addr);
- for (i = 0; i < 32; i++)
- value |= (((crc32 >> i) & 1) << (31 - i));
-
- return value;
-}
-
-/*
- * Sets the bit in the multicast table corresponding to the hash value.
- * hw - Struct containing variables accessed by shared code
- * hash_value - Multicast address hash value
- */
-void atl1_hash_set(struct atl1_hw *hw, u32 hash_value)
-{
- u32 hash_bit, hash_reg;
- u32 mta;
-
- /*
- * The HASH Table is a register array of 2 32-bit registers.
- * It is treated like an array of 64 bits. We want to set
- * bit BitArray[hash_value]. So we figure out what register
- * the bit is in, read it, OR in the new bit, then write
- * back the new value. The register is determined by the
- * upper 7 bits of the hash value and the bit within that
- * register are determined by the lower 5 bits of the value.
- */
- hash_reg = (hash_value >> 31) & 0x1;
- hash_bit = (hash_value >> 26) & 0x1F;
- mta = ioread32((hw->hw_addr + REG_RX_HASH_TABLE) + (hash_reg << 2));
- mta |= (1 << hash_bit);
- iowrite32(mta, (hw->hw_addr + REG_RX_HASH_TABLE) + (hash_reg << 2));
-}
-
-/*
- * Writes a value to a PHY register
- * hw - Struct containing variables accessed by shared code
- * reg_addr - address of the PHY register to write
- * data - data to write to the PHY
- */
-s32 atl1_write_phy_reg(struct atl1_hw *hw, u32 reg_addr, u16 phy_data)
-{
- int i;
- u32 val;
-
- val = ((u32) (phy_data & MDIO_DATA_MASK)) << MDIO_DATA_SHIFT |
- (reg_addr & MDIO_REG_ADDR_MASK) << MDIO_REG_ADDR_SHIFT |
- MDIO_SUP_PREAMBLE |
- MDIO_START | MDIO_CLK_25_4 << MDIO_CLK_SEL_SHIFT;
- iowrite32(val, hw->hw_addr + REG_MDIO_CTRL);
- ioread32(hw->hw_addr + REG_MDIO_CTRL);
-
- for (i = 0; i < MDIO_WAIT_TIMES; i++) {
- udelay(2);
- val = ioread32(hw->hw_addr + REG_MDIO_CTRL);
- if (!(val & (MDIO_START | MDIO_BUSY)))
- break;
- }
-
- if (!(val & (MDIO_START | MDIO_BUSY)))
- return ATL1_SUCCESS;
-
- return ATL1_ERR_PHY;
-}
-
-/*
- * Make L001's PHY out of Power Saving State (bug)
- * hw - Struct containing variables accessed by shared code
- * when power on, L001's PHY always on Power saving State
- * (Gigabit Link forbidden)
- */
-static s32 atl1_phy_leave_power_saving(struct atl1_hw *hw)
-{
- s32 ret;
- ret = atl1_write_phy_reg(hw, 29, 0x0029);
- if (ret)
- return ret;
- return atl1_write_phy_reg(hw, 30, 0);
-}
-
-/*
- *TODO: do something or get rid of this
- */
-s32 atl1_phy_enter_power_saving(struct atl1_hw *hw)
-{
-/* s32 ret_val;
- * u16 phy_data;
- */
-
-/*
- ret_val = atl1_write_phy_reg(hw, ...);
- ret_val = atl1_write_phy_reg(hw, ...);
- ....
-*/
- return ATL1_SUCCESS;
-}
-
-/*
- * Resets the PHY and make all config validate
- * hw - Struct containing variables accessed by shared code
- *
- * Sets bit 15 and 12 of the MII Control regiser (for F001 bug)
- */
-static s32 atl1_phy_reset(struct atl1_hw *hw)
-{
- struct pci_dev *pdev = hw->back->pdev;
- s32 ret_val;
- u16 phy_data;
-
- if (hw->media_type == MEDIA_TYPE_AUTO_SENSOR ||
- hw->media_type == MEDIA_TYPE_1000M_FULL)
- phy_data = MII_CR_RESET | MII_CR_AUTO_NEG_EN;
- else {
- switch (hw->media_type) {
- case MEDIA_TYPE_100M_FULL:
- phy_data =
- MII_CR_FULL_DUPLEX | MII_CR_SPEED_100 |
- MII_CR_RESET;
- break;
- case MEDIA_TYPE_100M_HALF:
- phy_data = MII_CR_SPEED_100 | MII_CR_RESET;
- break;
- case MEDIA_TYPE_10M_FULL:
- phy_data =
- MII_CR_FULL_DUPLEX | MII_CR_SPEED_10 | MII_CR_RESET;
- break;
- default: /* MEDIA_TYPE_10M_HALF: */
- phy_data = MII_CR_SPEED_10 | MII_CR_RESET;
- break;
- }
- }
-
- ret_val = atl1_write_phy_reg(hw, MII_BMCR, phy_data);
- if (ret_val) {
- u32 val;
- int i;
- /* pcie serdes link may be down! */
- dev_dbg(&pdev->dev, "pcie phy link down\n");
-
- for (i = 0; i < 25; i++) {
- msleep(1);
- val = ioread32(hw->hw_addr + REG_MDIO_CTRL);
- if (!(val & (MDIO_START | MDIO_BUSY)))
- break;
- }
-
- if ((val & (MDIO_START | MDIO_BUSY)) != 0) {
- dev_warn(&pdev->dev, "pcie link down at least 25ms\n");
- return ret_val;
- }
- }
- return ATL1_SUCCESS;
-}
-
-/*
- * Configures PHY autoneg and flow control advertisement settings
- * hw - Struct containing variables accessed by shared code
- */
-s32 atl1_phy_setup_autoneg_adv(struct atl1_hw *hw)
-{
- s32 ret_val;
- s16 mii_autoneg_adv_reg;
- s16 mii_1000t_ctrl_reg;
-
- /* Read the MII Auto-Neg Advertisement Register (Address 4). */
- mii_autoneg_adv_reg = MII_AR_DEFAULT_CAP_MASK;
-
- /* Read the MII 1000Base-T Control Register (Address 9). */
- mii_1000t_ctrl_reg = MII_AT001_CR_1000T_DEFAULT_CAP_MASK;
-
- /*
- * First we clear all the 10/100 mb speed bits in the Auto-Neg
- * Advertisement Register (Address 4) and the 1000 mb speed bits in
- * the 1000Base-T Control Register (Address 9).
- */
- mii_autoneg_adv_reg &= ~MII_AR_SPEED_MASK;
- mii_1000t_ctrl_reg &= ~MII_AT001_CR_1000T_SPEED_MASK;
-
- /*
- * Need to parse media_type and set up
- * the appropriate PHY registers.
- */
- switch (hw->media_type) {
- case MEDIA_TYPE_AUTO_SENSOR:
- mii_autoneg_adv_reg |= (MII_AR_10T_HD_CAPS |
- MII_AR_10T_FD_CAPS |
- MII_AR_100TX_HD_CAPS |
- MII_AR_100TX_FD_CAPS);
- mii_1000t_ctrl_reg |= MII_AT001_CR_1000T_FD_CAPS;
- break;
-
- case MEDIA_TYPE_1000M_FULL:
- mii_1000t_ctrl_reg |= MII_AT001_CR_1000T_FD_CAPS;
- break;
-
- case MEDIA_TYPE_100M_FULL:
- mii_autoneg_adv_reg |= MII_AR_100TX_FD_CAPS;
- break;
-
- case MEDIA_TYPE_100M_HALF:
- mii_autoneg_adv_reg |= MII_AR_100TX_HD_CAPS;
- break;
-
- case MEDIA_TYPE_10M_FULL:
- mii_autoneg_adv_reg |= MII_AR_10T_FD_CAPS;
- break;
-
- default:
- mii_autoneg_adv_reg |= MII_AR_10T_HD_CAPS;
- break;
- }
-
- /* flow control fixed to enable all */
- mii_autoneg_adv_reg |= (MII_AR_ASM_DIR | MII_AR_PAUSE);
-
- hw->mii_autoneg_adv_reg = mii_autoneg_adv_reg;
- hw->mii_1000t_ctrl_reg = mii_1000t_ctrl_reg;
-
- ret_val = atl1_write_phy_reg(hw, MII_ADVERTISE, mii_autoneg_adv_reg);
- if (ret_val)
- return ret_val;
-
- ret_val = atl1_write_phy_reg(hw, MII_AT001_CR, mii_1000t_ctrl_reg);
- if (ret_val)
- return ret_val;
-
- return ATL1_SUCCESS;
-}
-
-/*
- * Configures link settings.
- * hw - Struct containing variables accessed by shared code
- * Assumes the hardware has previously been reset and the
- * transmitter and receiver are not enabled.
- */
-static s32 atl1_setup_link(struct atl1_hw *hw)
-{
- struct pci_dev *pdev = hw->back->pdev;
- s32 ret_val;
-
- /*
- * Options:
- * PHY will advertise value(s) parsed from
- * autoneg_advertised and fc
- * no matter what autoneg is , We will not wait link result.
- */
- ret_val = atl1_phy_setup_autoneg_adv(hw);
- if (ret_val) {
- dev_dbg(&pdev->dev, "error setting up autonegotiation\n");
- return ret_val;
- }
- /* SW.Reset , En-Auto-Neg if needed */
- ret_val = atl1_phy_reset(hw);
- if (ret_val) {
- dev_dbg(&pdev->dev, "error resetting phy\n");
- return ret_val;
- }
- hw->phy_configured = true;
- return ret_val;
-}
-
-static struct atl1_spi_flash_dev flash_table[] = {
-/* MFR_NAME WRSR READ PRGM WREN WRDI RDSR RDID SECTOR_ERASE CHIP_ERASE */
- {"Atmel", 0x00, 0x03, 0x02, 0x06, 0x04, 0x05, 0x15, 0x52, 0x62},
- {"SST", 0x01, 0x03, 0x02, 0x06, 0x04, 0x05, 0x90, 0x20, 0x60},
- {"ST", 0x01, 0x03, 0x02, 0x06, 0x04, 0x05, 0xAB, 0xD8, 0xC7},
-};
-
-static void atl1_init_flash_opcode(struct atl1_hw *hw)
-{
- if (hw->flash_vendor >= ARRAY_SIZE(flash_table))
- hw->flash_vendor = 0; /* ATMEL */
-
- /* Init OP table */
- iowrite8(flash_table[hw->flash_vendor].cmd_program,
- hw->hw_addr + REG_SPI_FLASH_OP_PROGRAM);
- iowrite8(flash_table[hw->flash_vendor].cmd_sector_erase,
- hw->hw_addr + REG_SPI_FLASH_OP_SC_ERASE);
- iowrite8(flash_table[hw->flash_vendor].cmd_chip_erase,
- hw->hw_addr + REG_SPI_FLASH_OP_CHIP_ERASE);
- iowrite8(flash_table[hw->flash_vendor].cmd_rdid,
- hw->hw_addr + REG_SPI_FLASH_OP_RDID);
- iowrite8(flash_table[hw->flash_vendor].cmd_wren,
- hw->hw_addr + REG_SPI_FLASH_OP_WREN);
- iowrite8(flash_table[hw->flash_vendor].cmd_rdsr,
- hw->hw_addr + REG_SPI_FLASH_OP_RDSR);
- iowrite8(flash_table[hw->flash_vendor].cmd_wrsr,
- hw->hw_addr + REG_SPI_FLASH_OP_WRSR);
- iowrite8(flash_table[hw->flash_vendor].cmd_read,
- hw->hw_addr + REG_SPI_FLASH_OP_READ);
-}
-
-/*
- * Performs basic configuration of the adapter.
- * hw - Struct containing variables accessed by shared code
- * Assumes that the controller has previously been reset and is in a
- * post-reset uninitialized state. Initializes multicast table,
- * and Calls routines to setup link
- * Leaves the transmit and receive units disabled and uninitialized.
- */
-s32 atl1_init_hw(struct atl1_hw *hw)
-{
- u32 ret_val = 0;
-
- /* Zero out the Multicast HASH table */
- iowrite32(0, hw->hw_addr + REG_RX_HASH_TABLE);
- /* clear the old settings from the multicast hash table */
- iowrite32(0, (hw->hw_addr + REG_RX_HASH_TABLE) + (1 << 2));
-
- atl1_init_flash_opcode(hw);
-
- if (!hw->phy_configured) {
- /* enable GPHY LinkChange Interrrupt */
- ret_val = atl1_write_phy_reg(hw, 18, 0xC00);
- if (ret_val)
- return ret_val;
- /* make PHY out of power-saving state */
- ret_val = atl1_phy_leave_power_saving(hw);
- if (ret_val)
- return ret_val;
- /* Call a subroutine to configure the link */
- ret_val = atl1_setup_link(hw);
- }
- return ret_val;
-}
-
-/*
- * Detects the current speed and duplex settings of the hardware.
- * hw - Struct containing variables accessed by shared code
- * speed - Speed of the connection
- * duplex - Duplex setting of the connection
- */
-s32 atl1_get_speed_and_duplex(struct atl1_hw *hw, u16 *speed, u16 *duplex)
-{
- struct pci_dev *pdev = hw->back->pdev;
- s32 ret_val;
- u16 phy_data;
-
- /* ; --- Read PHY Specific Status Register (17) */
- ret_val = atl1_read_phy_reg(hw, MII_AT001_PSSR, &phy_data);
- if (ret_val)
- return ret_val;
-
- if (!(phy_data & MII_AT001_PSSR_SPD_DPLX_RESOLVED))
- return ATL1_ERR_PHY_RES;
-
- switch (phy_data & MII_AT001_PSSR_SPEED) {
- case MII_AT001_PSSR_1000MBS:
- *speed = SPEED_1000;
- break;
- case MII_AT001_PSSR_100MBS:
- *speed = SPEED_100;
- break;
- case MII_AT001_PSSR_10MBS:
- *speed = SPEED_10;
- break;
- default:
- dev_dbg(&pdev->dev, "error getting speed\n");
- return ATL1_ERR_PHY_SPEED;
- break;
- }
- if (phy_data & MII_AT001_PSSR_DPLX)
- *duplex = FULL_DUPLEX;
- else
- *duplex = HALF_DUPLEX;
-
- return ATL1_SUCCESS;
-}
-
-void atl1_set_mac_addr(struct atl1_hw *hw)
-{
- u32 value;
- /*
- * 00-0B-6A-F6-00-DC
- * 0: 6AF600DC 1: 000B
- * low dword
- */
- value = (((u32) hw->mac_addr[2]) << 24) |
- (((u32) hw->mac_addr[3]) << 16) |
- (((u32) hw->mac_addr[4]) << 8) | (((u32) hw->mac_addr[5]));
- iowrite32(value, hw->hw_addr + REG_MAC_STA_ADDR);
- /* high dword */
- value = (((u32) hw->mac_addr[0]) << 8) | (((u32) hw->mac_addr[1]));
- iowrite32(value, (hw->hw_addr + REG_MAC_STA_ADDR) + (1 << 2));
-}
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-23 02:37:49 +0000