aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/e1000e/es2lan.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/e1000e/es2lan.c')
-rw-r--r--drivers/net/e1000e/es2lan.c89
1 files changed, 52 insertions, 37 deletions
diff --git a/drivers/net/e1000e/es2lan.c b/drivers/net/e1000e/es2lan.c
index 88657adf965f..265775447538 100644
--- a/drivers/net/e1000e/es2lan.c
+++ b/drivers/net/e1000e/es2lan.c
@@ -1,7 +1,7 @@
/*******************************************************************************
Intel PRO/1000 Linux driver
- Copyright(c) 1999 - 2007 Intel Corporation.
+ Copyright(c) 1999 - 2008 Intel Corporation.
This program is free software; you can redistribute it and/or modify it
under the terms and conditions of the GNU General Public License,
@@ -92,7 +92,8 @@
/* In-Band Control Register (Page 194, Register 18) */
#define GG82563_ICR_DIS_PADDING 0x0010 /* Disable Padding */
-/* A table for the GG82563 cable length where the range is defined
+/*
+ * A table for the GG82563 cable length where the range is defined
* with a lower bound at "index" and the upper bound at
* "index + 5".
*/
@@ -167,12 +168,13 @@ static s32 e1000_init_nvm_params_80003es2lan(struct e1000_hw *hw)
break;
}
- nvm->type = e1000_nvm_eeprom_spi;
+ nvm->type = e1000_nvm_eeprom_spi;
size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >>
E1000_EECD_SIZE_EX_SHIFT);
- /* Added to a constant, "size" becomes the left-shift value
+ /*
+ * Added to a constant, "size" becomes the left-shift value
* for setting word_size.
*/
size += NVM_WORD_SIZE_BASE_SHIFT;
@@ -208,8 +210,7 @@ static s32 e1000_init_mac_params_80003es2lan(struct e1000_adapter *adapter)
/* Set rar entry count */
mac->rar_entry_count = E1000_RAR_ENTRIES;
/* Set if manageability features are enabled. */
- mac->arc_subsystem_valid =
- (er32(FWSM) & E1000_FWSM_MODE_MASK) ? 1 : 0;
+ mac->arc_subsystem_valid = (er32(FWSM) & E1000_FWSM_MODE_MASK) ? 1 : 0;
/* check for link */
switch (hw->media_type) {
@@ -344,8 +345,10 @@ static s32 e1000_acquire_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask)
if (!(swfw_sync & (fwmask | swmask)))
break;
- /* Firmware currently using resource (fwmask)
- * or other software thread using resource (swmask) */
+ /*
+ * Firmware currently using resource (fwmask)
+ * or other software thread using resource (swmask)
+ */
e1000e_put_hw_semaphore(hw);
mdelay(5);
i++;
@@ -407,7 +410,8 @@ static s32 e1000_read_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw,
if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG)
page_select = GG82563_PHY_PAGE_SELECT;
else
- /* Use Alternative Page Select register to access
+ /*
+ * Use Alternative Page Select register to access
* registers 30 and 31
*/
page_select = GG82563_PHY_PAGE_SELECT_ALT;
@@ -417,7 +421,8 @@ static s32 e1000_read_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw,
if (ret_val)
return ret_val;
- /* The "ready" bit in the MDIC register may be incorrectly set
+ /*
+ * The "ready" bit in the MDIC register may be incorrectly set
* before the device has completed the "Page Select" MDI
* transaction. So we wait 200us after each MDI command...
*/
@@ -462,7 +467,8 @@ static s32 e1000_write_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw,
if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG)
page_select = GG82563_PHY_PAGE_SELECT;
else
- /* Use Alternative Page Select register to access
+ /*
+ * Use Alternative Page Select register to access
* registers 30 and 31
*/
page_select = GG82563_PHY_PAGE_SELECT_ALT;
@@ -473,7 +479,8 @@ static s32 e1000_write_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw,
return ret_val;
- /* The "ready" bit in the MDIC register may be incorrectly set
+ /*
+ * The "ready" bit in the MDIC register may be incorrectly set
* before the device has completed the "Page Select" MDI
* transaction. So we wait 200us after each MDI command...
*/
@@ -554,7 +561,8 @@ static s32 e1000_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw)
u16 phy_data;
bool link;
- /* Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI
+ /*
+ * Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI
* forced whenever speed and duplex are forced.
*/
ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
@@ -593,7 +601,8 @@ static s32 e1000_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw)
return ret_val;
if (!link) {
- /* We didn't get link.
+ /*
+ * We didn't get link.
* Reset the DSP and cross our fingers.
*/
ret_val = e1000e_phy_reset_dsp(hw);
@@ -612,7 +621,8 @@ static s32 e1000_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw)
if (ret_val)
return ret_val;
- /* Resetting the phy means we need to verify the TX_CLK corresponds
+ /*
+ * Resetting the phy means we need to verify the TX_CLK corresponds
* to the link speed. 10Mbps -> 2.5MHz, else 25MHz.
*/
phy_data &= ~GG82563_MSCR_TX_CLK_MASK;
@@ -621,7 +631,8 @@ static s32 e1000_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw)
else
phy_data |= GG82563_MSCR_TX_CLK_100MBPS_25;
- /* In addition, we must re-enable CRS on Tx for both half and full
+ /*
+ * In addition, we must re-enable CRS on Tx for both half and full
* duplex.
*/
phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX;
@@ -704,7 +715,8 @@ static s32 e1000_reset_hw_80003es2lan(struct e1000_hw *hw)
u32 icr;
s32 ret_val;
- /* Prevent the PCI-E bus from sticking if there is no TLP connection
+ /*
+ * Prevent the PCI-E bus from sticking if there is no TLP connection
* on the last TLP read/write transaction when MAC is reset.
*/
ret_val = e1000e_disable_pcie_master(hw);
@@ -808,7 +820,8 @@ static s32 e1000_init_hw_80003es2lan(struct e1000_hw *hw)
reg_data &= ~0x00100000;
E1000_WRITE_REG_ARRAY(hw, E1000_FFLT, 0x0001, reg_data);
- /* Clear all of the statistics registers (clear on read). It is
+ /*
+ * Clear all of the statistics registers (clear on read). It is
* important that we do this after we have tried to establish link
* because the symbol error count will increment wildly if there
* is no link.
@@ -881,7 +894,8 @@ static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw)
if (ret_val)
return ret_val;
- /* Options:
+ /*
+ * Options:
* MDI/MDI-X = 0 (default)
* 0 - Auto for all speeds
* 1 - MDI mode
@@ -907,7 +921,8 @@ static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw)
break;
}
- /* Options:
+ /*
+ * Options:
* disable_polarity_correction = 0 (default)
* Automatic Correction for Reversed Cable Polarity
* 0 - Disabled
@@ -928,10 +943,9 @@ static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw)
return ret_val;
}
- /* Bypass RX and TX FIFO's */
- ret_val = e1000e_write_kmrn_reg(hw,
- E1000_KMRNCTRLSTA_OFFSET_FIFO_CTRL,
- E1000_KMRNCTRLSTA_FIFO_CTRL_RX_BYPASS |
+ /* Bypass Rx and Tx FIFO's */
+ ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_OFFSET_FIFO_CTRL,
+ E1000_KMRNCTRLSTA_FIFO_CTRL_RX_BYPASS |
E1000_KMRNCTRLSTA_FIFO_CTRL_TX_BYPASS);
if (ret_val)
return ret_val;
@@ -953,7 +967,8 @@ static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw)
if (ret_val)
return ret_val;
- /* Do not init these registers when the HW is in IAMT mode, since the
+ /*
+ * Do not init these registers when the HW is in IAMT mode, since the
* firmware will have already initialized them. We only initialize
* them if the HW is not in IAMT mode.
*/
@@ -974,7 +989,8 @@ static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw)
return ret_val;
}
- /* Workaround: Disable padding in Kumeran interface in the MAC
+ /*
+ * Workaround: Disable padding in Kumeran interface in the MAC
* and in the PHY to avoid CRC errors.
*/
ret_val = e1e_rphy(hw, GG82563_PHY_INBAND_CTRL, &data);
@@ -1007,9 +1023,11 @@ static s32 e1000_setup_copper_link_80003es2lan(struct e1000_hw *hw)
ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
ew32(CTRL, ctrl);
- /* Set the mac to wait the maximum time between each
+ /*
+ * Set the mac to wait the maximum time between each
* iteration and increase the max iterations when
- * polling the phy; this fixes erroneous timeouts at 10Mbps. */
+ * polling the phy; this fixes erroneous timeouts at 10Mbps.
+ */
ret_val = e1000e_write_kmrn_reg(hw, GG82563_REG(0x34, 4), 0xFFFF);
if (ret_val)
return ret_val;
@@ -1026,9 +1044,8 @@ static s32 e1000_setup_copper_link_80003es2lan(struct e1000_hw *hw)
if (ret_val)
return ret_val;
reg_data |= E1000_KMRNCTRLSTA_INB_CTRL_DIS_PADDING;
- ret_val = e1000e_write_kmrn_reg(hw,
- E1000_KMRNCTRLSTA_OFFSET_INB_CTRL,
- reg_data);
+ ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_OFFSET_INB_CTRL,
+ reg_data);
if (ret_val)
return ret_val;
@@ -1056,9 +1073,8 @@ static s32 e1000_cfg_kmrn_10_100_80003es2lan(struct e1000_hw *hw, u16 duplex)
u16 reg_data;
reg_data = E1000_KMRNCTRLSTA_HD_CTRL_10_100_DEFAULT;
- ret_val = e1000e_write_kmrn_reg(hw,
- E1000_KMRNCTRLSTA_OFFSET_HD_CTRL,
- reg_data);
+ ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_OFFSET_HD_CTRL,
+ reg_data);
if (ret_val)
return ret_val;
@@ -1096,9 +1112,8 @@ static s32 e1000_cfg_kmrn_1000_80003es2lan(struct e1000_hw *hw)
u32 tipg;
reg_data = E1000_KMRNCTRLSTA_HD_CTRL_1000_DEFAULT;
- ret_val = e1000e_write_kmrn_reg(hw,
- E1000_KMRNCTRLSTA_OFFSET_HD_CTRL,
- reg_data);
+ ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_OFFSET_HD_CTRL,
+ reg_data);
if (ret_val)
return ret_val;
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-20 18:17:38 +0000