1 files changed, 39 insertions, 0 deletions
diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c
index cf74d108953e..a52b560e428b 100644
--- a/drivers/net/phy/at803x.c
+++ b/drivers/net/phy/at803x.c
@@ -42,10 +42,18 @@
 #define AT803X_MMD_ACCESS_CONTROL		0x0D
 #define AT803X_MMD_ACCESS_CONTROL_DATA		0x0E
 #define AT803X_FUNC_DATA			0x4003
+#define AT803X_REG_CHIP_CONFIG			0x1f
+#define AT803X_BT_BX_REG_SEL			0x8000
 
 #define AT803X_DEBUG_ADDR			0x1D
 #define AT803X_DEBUG_DATA			0x1E
 
+#define AT803X_MODE_CFG_MASK			0x0F
+#define AT803X_MODE_CFG_SGMII			0x01
+
+#define AT803X_PSSR			0x11	/*PHY-Specific Status Register*/
+#define AT803X_PSSR_MR_AN_COMPLETE	0x0200
+
 #define AT803X_DEBUG_REG_0			0x00
 #define AT803X_DEBUG_RX_CLK_DLY_EN		BIT(15)
 
@@ -355,6 +363,36 @@ static void at803x_link_change_notify(struct phy_device *phydev)
 	}
 }
 
+static int at803x_aneg_done(struct phy_device *phydev)
+{
+	int ccr;
+
+	int aneg_done = genphy_aneg_done(phydev);
+	if (aneg_done != BMSR_ANEGCOMPLETE)
+		return aneg_done;
+
+	/*
+	 * in SGMII mode, if copper side autoneg is successful,
+	 * also check SGMII side autoneg result
+	 */
+	ccr = phy_read(phydev, AT803X_REG_CHIP_CONFIG);
+	if ((ccr & AT803X_MODE_CFG_MASK) != AT803X_MODE_CFG_SGMII)
+		return aneg_done;
+
+	/* switch to SGMII/fiber page */
+	phy_write(phydev, AT803X_REG_CHIP_CONFIG, ccr & ~AT803X_BT_BX_REG_SEL);
+
+	/* check if the SGMII link is OK. */
+	if (!(phy_read(phydev, AT803X_PSSR) & AT803X_PSSR_MR_AN_COMPLETE)) {
+		pr_warn("803x_aneg_done: SGMII link is not ok\n");
+		aneg_done = 0;
+	}
+	/* switch back to copper page */
+	phy_write(phydev, AT803X_REG_CHIP_CONFIG, ccr | AT803X_BT_BX_REG_SEL);
+
+	return aneg_done;
+}
+
 static struct phy_driver at803x_driver[] = {
 {
 	/* ATHEROS 8035 */
@@ -406,6 +444,7 @@ static struct phy_driver at803x_driver[] = {
 	.flags			= PHY_HAS_INTERRUPT,
 	.config_aneg		= genphy_config_aneg,
 	.read_status		= genphy_read_status,
+	.aneg_done		= at803x_aneg_done,
 	.ack_interrupt		= &at803x_ack_interrupt,
 	.config_intr		= &at803x_config_intr,
 } };