diff options
Diffstat (limited to 'drivers/spi')
| -rw-r--r-- | drivers/spi/Kconfig | 9 | ||||
| -rw-r--r-- | drivers/spi/Makefile | 1 | ||||
| -rw-r--r-- | drivers/spi/atmel-quadspi.c | 549 | ||||
| -rw-r--r-- | drivers/spi/spi-mem.c | 269 |
4 files changed, 806 insertions, 22 deletions
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index a5b0761c890f..9f89cb134549 100644 --- a/drivers/spi/Kconfig +++ b/drivers/spi/Kconfig @@ -91,6 +91,15 @@ config SPI_AT91_USART This selects a driver for the AT91 USART Controller as SPI Master, present on AT91 and SAMA5 SoC series. +config SPI_ATMEL_QUADSPI + tristate "Atmel Quad SPI Controller" + depends on ARCH_AT91 || (ARM && COMPILE_TEST && !ARCH_EBSA110) + depends on OF && HAS_IOMEM + help + This enables support for the Quad SPI controller in master mode. + This driver does not support generic SPI. The implementation only + supports spi-mem interface. + config SPI_AU1550 tristate "Au1550/Au1200/Au1300 SPI Controller" depends on MIPS_ALCHEMY diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index 0c4b7a8debf8..f29627040dfb 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -16,6 +16,7 @@ obj-$(CONFIG_SPI_LOOPBACK_TEST) += spi-loopback-test.o obj-$(CONFIG_SPI_ALTERA) += spi-altera.o obj-$(CONFIG_SPI_ARMADA_3700) += spi-armada-3700.o obj-$(CONFIG_SPI_ATMEL) += spi-atmel.o +obj-$(CONFIG_SPI_ATMEL_QUADSPI) += atmel-quadspi.o obj-$(CONFIG_SPI_AT91_USART) += spi-at91-usart.o obj-$(CONFIG_SPI_ATH79) += spi-ath79.o obj-$(CONFIG_SPI_AU1550) += spi-au1550.o diff --git a/drivers/spi/atmel-quadspi.c b/drivers/spi/atmel-quadspi.c new file mode 100644 index 000000000000..ddc712410812 --- /dev/null +++ b/drivers/spi/atmel-quadspi.c @@ -0,0 +1,549 @@ +/* + * Driver for Atmel QSPI Controller + * + * Copyright (C) 2015 Atmel Corporation + * Copyright (C) 2018 Cryptera A/S + * + * Author: Cyrille Pitchen <cyrille.pitchen@atmel.com> + * Author: Piotr Bugalski <bugalski.piotr@gmail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + * + * This driver is based on drivers/mtd/spi-nor/fsl-quadspi.c from Freescale. + */ + +#include <linux/kernel.h> +#include <linux/clk.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/delay.h> +#include <linux/err.h> +#include <linux/interrupt.h> +#include <linux/of.h> + +#include <linux/io.h> +#include <linux/spi/spi-mem.h> + +/* QSPI register offsets */ +#define QSPI_CR 0x0000 /* Control Register */ +#define QSPI_MR 0x0004 /* Mode Register */ +#define QSPI_RD 0x0008 /* Receive Data Register */ +#define QSPI_TD 0x000c /* Transmit Data Register */ +#define QSPI_SR 0x0010 /* Status Register */ +#define QSPI_IER 0x0014 /* Interrupt Enable Register */ +#define QSPI_IDR 0x0018 /* Interrupt Disable Register */ +#define QSPI_IMR 0x001c /* Interrupt Mask Register */ +#define QSPI_SCR 0x0020 /* Serial Clock Register */ + +#define QSPI_IAR 0x0030 /* Instruction Address Register */ +#define QSPI_ICR 0x0034 /* Instruction Code Register */ +#define QSPI_IFR 0x0038 /* Instruction Frame Register */ + +#define QSPI_SMR 0x0040 /* Scrambling Mode Register */ +#define QSPI_SKR 0x0044 /* Scrambling Key Register */ + +#define QSPI_WPMR 0x00E4 /* Write Protection Mode Register */ +#define QSPI_WPSR 0x00E8 /* Write Protection Status Register */ + +#define QSPI_VERSION 0x00FC /* Version Register */ + + +/* Bitfields in QSPI_CR (Control Register) */ +#define QSPI_CR_QSPIEN BIT(0) +#define QSPI_CR_QSPIDIS BIT(1) +#define QSPI_CR_SWRST BIT(7) +#define QSPI_CR_LASTXFER BIT(24) + +/* Bitfields in QSPI_MR (Mode Register) */ +#define QSPI_MR_SMM BIT(0) +#define QSPI_MR_LLB BIT(1) +#define QSPI_MR_WDRBT BIT(2) +#define QSPI_MR_SMRM BIT(3) +#define QSPI_MR_CSMODE_MASK GENMASK(5, 4) +#define QSPI_MR_CSMODE_NOT_RELOADED (0 << 4) +#define QSPI_MR_CSMODE_LASTXFER (1 << 4) +#define QSPI_MR_CSMODE_SYSTEMATICALLY (2 << 4) +#define QSPI_MR_NBBITS_MASK GENMASK(11, 8) +#define QSPI_MR_NBBITS(n) ((((n) - 8) << 8) & QSPI_MR_NBBITS_MASK) +#define QSPI_MR_DLYBCT_MASK GENMASK(23, 16) +#define QSPI_MR_DLYBCT(n) (((n) << 16) & QSPI_MR_DLYBCT_MASK) +#define QSPI_MR_DLYCS_MASK GENMASK(31, 24) +#define QSPI_MR_DLYCS(n) (((n) << 24) & QSPI_MR_DLYCS_MASK) + +/* Bitfields in QSPI_SR/QSPI_IER/QSPI_IDR/QSPI_IMR */ +#define QSPI_SR_RDRF BIT(0) +#define QSPI_SR_TDRE BIT(1) +#define QSPI_SR_TXEMPTY BIT(2) +#define QSPI_SR_OVRES BIT(3) +#define QSPI_SR_CSR BIT(8) +#define QSPI_SR_CSS BIT(9) +#define QSPI_SR_INSTRE BIT(10) +#define QSPI_SR_QSPIENS BIT(24) + +#define QSPI_SR_CMD_COMPLETED (QSPI_SR_INSTRE | QSPI_SR_CSR) + +/* Bitfields in QSPI_SCR (Serial Clock Register) */ +#define QSPI_SCR_CPOL BIT(0) +#define QSPI_SCR_CPHA BIT(1) +#define QSPI_SCR_SCBR_MASK GENMASK(15, 8) +#define QSPI_SCR_SCBR(n) (((n) << 8) & QSPI_SCR_SCBR_MASK) +#define QSPI_SCR_DLYBS_MASK GENMASK(23, 16) +#define QSPI_SCR_DLYBS(n) (((n) << 16) & QSPI_SCR_DLYBS_MASK) + +/* Bitfields in QSPI_ICR (Instruction Code Register) */ +#define QSPI_ICR_INST_MASK GENMASK(7, 0) +#define QSPI_ICR_INST(inst) (((inst) << 0) & QSPI_ICR_INST_MASK) +#define QSPI_ICR_OPT_MASK GENMASK(23, 16) +#define QSPI_ICR_OPT(opt) (((opt) << 16) & QSPI_ICR_OPT_MASK) + +/* Bitfields in QSPI_IFR (Instruction Frame Register) */ +#define QSPI_IFR_WIDTH_MASK GENMASK(2, 0) +#define QSPI_IFR_WIDTH_SINGLE_BIT_SPI (0 << 0) +#define QSPI_IFR_WIDTH_DUAL_OUTPUT (1 << 0) +#define QSPI_IFR_WIDTH_QUAD_OUTPUT (2 << 0) +#define QSPI_IFR_WIDTH_DUAL_IO (3 << 0) +#define QSPI_IFR_WIDTH_QUAD_IO (4 << 0) +#define QSPI_IFR_WIDTH_DUAL_CMD (5 << 0) +#define QSPI_IFR_WIDTH_QUAD_CMD (6 << 0) +#define QSPI_IFR_INSTEN BIT(4) +#define QSPI_IFR_ADDREN BIT(5) +#define QSPI_IFR_OPTEN BIT(6) +#define QSPI_IFR_DATAEN BIT(7) +#define QSPI_IFR_OPTL_MASK GENMASK(9, 8) +#define QSPI_IFR_OPTL_1BIT (0 << 8) +#define QSPI_IFR_OPTL_2BIT (1 << 8) +#define QSPI_IFR_OPTL_4BIT (2 << 8) +#define QSPI_IFR_OPTL_8BIT (3 << 8) +#define QSPI_IFR_ADDRL BIT(10) +#define QSPI_IFR_TFRTYP_MASK GENMASK(13, 12) +#define QSPI_IFR_TFRTYP_TRSFR_READ (0 << 12) +#define QSPI_IFR_TFRTYP_TRSFR_READ_MEM (1 << 12) +#define QSPI_IFR_TFRTYP_TRSFR_WRITE (2 << 12) +#define QSPI_IFR_TFRTYP_TRSFR_WRITE_MEM (3 << 13) +#define QSPI_IFR_CRM BIT(14) +#define QSPI_IFR_NBDUM_MASK GENMASK(20, 16) +#define QSPI_IFR_NBDUM(n) (((n) << 16) & QSPI_IFR_NBDUM_MASK) + +/* Bitfields in QSPI_SMR (Scrambling Mode Register) */ +#define QSPI_SMR_SCREN BIT(0) +#define QSPI_SMR_RVDIS BIT(1) + +/* Bitfields in QSPI_WPMR (Write Protection Mode Register) */ +#define QSPI_WPMR_WPEN BIT(0) +#define QSPI_WPMR_WPKEY_MASK GENMASK(31, 8) +#define QSPI_WPMR_WPKEY(wpkey) (((wpkey) << 8) & QSPI_WPMR_WPKEY_MASK) + +/* Bitfields in QSPI_WPSR (Write Protection Status Register) */ +#define QSPI_WPSR_WPVS BIT(0) +#define QSPI_WPSR_WPVSRC_MASK GENMASK(15, 8) +#define QSPI_WPSR_WPVSRC(src) (((src) << 8) & QSPI_WPSR_WPVSRC) + + +struct atmel_qspi { + void __iomem *regs; + void __iomem *mem; + struct clk *clk; + struct platform_device *pdev; + u32 pending; + struct completion cmd_completion; +}; + +struct qspi_mode { + u8 cmd_buswidth; + u8 addr_buswidth; + u8 data_buswidth; + u32 config; +}; + +static const struct qspi_mode sama5d2_qspi_modes[] = { + { 1, 1, 1, QSPI_IFR_WIDTH_SINGLE_BIT_SPI }, + { 1, 1, 2, QSPI_IFR_WIDTH_DUAL_OUTPUT }, + { 1, 1, 4, QSPI_IFR_WIDTH_QUAD_OUTPUT }, + { 1, 2, 2, QSPI_IFR_WIDTH_DUAL_IO }, + { 1, 4, 4, QSPI_IFR_WIDTH_QUAD_IO }, + { 2, 2, 2, QSPI_IFR_WIDTH_DUAL_CMD }, + { 4, 4, 4, QSPI_IFR_WIDTH_QUAD_CMD }, +}; + +/* Register access functions */ +static inline u32 qspi_readl(struct atmel_qspi *aq, u32 reg) +{ + return readl_relaxed(aq->regs + reg); +} + +static inline void qspi_writel(struct atmel_qspi *aq, u32 reg, u32 value) +{ + writel_relaxed(value, aq->regs + reg); +} + +static inline bool is_compatible(const struct spi_mem_op *op, + const struct qspi_mode *mode) +{ + if (op->cmd.buswidth != mode->cmd_buswidth) + return false; + + if (op->addr.nbytes && op->addr.buswidth != mode->addr_buswidth) + return false; + + if (op->data.nbytes && op->data.buswidth != mode->data_buswidth) + return false; + + return true; +} + +static int find_mode(const struct spi_mem_op *op) +{ + u32 i; + + for (i = 0; i < ARRAY_SIZE(sama5d2_qspi_modes); i++) + if (is_compatible(op, &sama5d2_qspi_modes[i])) + return i; + + return -1; +} + +static bool atmel_qspi_supports_op(struct spi_mem *mem, + const struct spi_mem_op *op) +{ + if (find_mode(op) < 0) + return false; + + /* special case not supported by hardware */ + if (op->addr.nbytes == 2 && op->cmd.buswidth != op->addr.buswidth && + op->dummy.nbytes == 0) + return false; + + return true; +} + +static int atmel_qspi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op) +{ + struct atmel_qspi *aq = spi_controller_get_devdata(mem->spi->master); + int mode; + u32 dummy_cycles = 0; + u32 iar, icr, ifr, sr; + int err = 0; + + iar = 0; + icr = QSPI_ICR_INST(op->cmd.opcode); + ifr = QSPI_IFR_INSTEN; + + qspi_writel(aq, QSPI_MR, QSPI_MR_SMM); + + mode = find_mode(op); + if (mode < 0) + return -ENOTSUPP; + + ifr |= sama5d2_qspi_modes[mode].config; + + if (op->dummy.buswidth && op->dummy.nbytes) + dummy_cycles = op->dummy.nbytes * 8 / op->dummy.buswidth; + + if (op->addr.buswidth) { + switch (op->addr.nbytes) { + case 0: + break; + case 1: + ifr |= QSPI_IFR_OPTEN | QSPI_IFR_OPTL_8BIT; + icr |= QSPI_ICR_OPT(op->addr.val & 0xff); + break; + case 2: + if (dummy_cycles < 8 / op->addr.buswidth) { + ifr &= ~QSPI_IFR_INSTEN; + ifr |= QSPI_IFR_ADDREN; + iar = (op->cmd.opcode << 16) | + (op->addr.val & 0xffff); + } else { + ifr |= QSPI_IFR_ADDREN; + iar = (op->addr.val << 8) & 0xffffff; + dummy_cycles -= 8 / op->addr.buswidth; + } + break; + case 3: + ifr |= QSPI_IFR_ADDREN; + iar = op->addr.val & 0xffffff; + break; + case 4: + ifr |= QSPI_IFR_ADDREN | QSPI_IFR_ADDRL; + iar = op->addr.val & 0x7ffffff; + break; + default: + return -ENOTSUPP; + } + } + + /* Set number of dummy cycles */ + if (dummy_cycles) + ifr |= QSPI_IFR_NBDUM(dummy_cycles); + + /* Set data enable */ + if (op->data.nbytes) + ifr |= QSPI_IFR_DATAEN; + + if (op->data.dir == SPI_MEM_DATA_IN && op->data.nbytes) + ifr |= QSPI_IFR_TFRTYP_TRSFR_READ; + else + ifr |= QSPI_IFR_TFRTYP_TRSFR_WRITE; + + /* Clear pending interrupts */ + (void)qspi_readl(aq, QSPI_SR); + + /* Set QSPI Instruction Frame registers */ + qspi_writel(aq, QSPI_IAR, iar); + qspi_writel(aq, QSPI_ICR, icr); + qspi_writel(aq, QSPI_IFR, ifr); + + /* Skip to the final steps if there is no data */ + if (op->data.nbytes) { + /* Dummy read of QSPI_IFR to synchronize APB and AHB accesses */ + (void)qspi_readl(aq, QSPI_IFR); + + /* Send/Receive data */ + if (op->data.dir == SPI_MEM_DATA_IN) + _memcpy_fromio(op->data.buf.in, + aq->mem + iar, op->data.nbytes); + else + _memcpy_toio(aq->mem + iar, + op->data.buf.out, op->data.nbytes); + + /* Release the chip-select */ + qspi_writel(aq, QSPI_CR, QSPI_CR_LASTXFER); + } + + /* Poll INSTRuction End status */ + sr = qspi_readl(aq, QSPI_SR); + if ((sr & QSPI_SR_CMD_COMPLETED) == QSPI_SR_CMD_COMPLETED) + return err; + + /* Wait for INSTRuction End interrupt */ + reinit_completion(&aq->cmd_completion); + aq->pending = sr & QSPI_SR_CMD_COMPLETED; + qspi_writel(aq, QSPI_IER, QSPI_SR_CMD_COMPLETED); + if (!wait_for_completion_timeout(&aq->cmd_completion, + msecs_to_jiffies(1000))) + err = -ETIMEDOUT; + qspi_writel(aq, QSPI_IDR, QSPI_SR_CMD_COMPLETED); + + return err; +} + +const char *atmel_qspi_get_name(struct spi_mem *spimem) +{ + return dev_name(spimem->spi->dev.parent); +} + +static const struct spi_controller_mem_ops atmel_qspi_mem_ops = { + .supports_op = atmel_qspi_supports_op, + .exec_op = atmel_qspi_exec_op, + .get_name = atmel_qspi_get_name +}; + +static int atmel_qspi_setup(struct spi_device *spi) +{ + struct spi_controller *ctrl = spi->master; + struct atmel_qspi *aq = spi_controller_get_devdata(ctrl); + unsigned long src_rate; + u32 scr, scbr; + + if (ctrl->busy) + return -EBUSY; + + if (!spi->max_speed_hz) + return -EINVAL; + + src_rate = clk_get_rate(aq->clk); + if (!src_rate) + return -EINVAL; + + /* Compute the QSPI baudrate */ + scbr = DIV_ROUND_UP(src_rate, spi->max_speed_hz); + if (scbr > 0) + scbr--; + + scr = QSPI_SCR_SCBR(scbr); + qspi_writel(aq, QSPI_SCR, scr); + + return 0; +} + +static int atmel_qspi_init(struct atmel_qspi *aq) +{ + /* Reset the QSPI controller */ + qspi_writel(aq, QSPI_CR, QSPI_CR_SWRST); + + /* Enable the QSPI controller */ + qspi_writel(aq, QSPI_CR, QSPI_CR_QSPIEN); + + return 0; +} + +static irqreturn_t atmel_qspi_interrupt(int irq, void *dev_id) +{ + struct atmel_qspi *aq = (struct atmel_qspi *)dev_id; + u32 status, mask, pending; + + status = qspi_readl(aq, QSPI_SR); + mask = qspi_readl(aq, QSPI_IMR); + pending = status & mask; + + if (!pending) + return IRQ_NONE; + + aq->pending |= pending; + if ((aq->pending & QSPI_SR_CMD_COMPLETED) == QSPI_SR_CMD_COMPLETED) + complete(&aq->cmd_completion); + + return IRQ_HANDLED; +} + +static int atmel_qspi_probe(struct platform_device *pdev) +{ + struct spi_controller *ctrl; + struct atmel_qspi *aq; + struct resource *res; + int irq, err = 0; + + ctrl = spi_alloc_master(&pdev->dev, sizeof(*aq)); + if (!ctrl) + return -ENOMEM; + + ctrl->mode_bits = SPI_RX_DUAL | SPI_RX_QUAD | SPI_TX_DUAL | SPI_TX_QUAD; + ctrl->setup = atmel_qspi_setup; + ctrl->bus_num = -1; + ctrl->mem_ops = &atmel_qspi_mem_ops; + ctrl->num_chipselect = 1; + ctrl->dev.of_node = pdev->dev.of_node; + platform_set_drvdata(pdev, ctrl); + + aq = spi_controller_get_devdata(ctrl); + + init_completion(&aq->cmd_completion); + aq->pdev = pdev; + + /* Map the registers */ + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "qspi_base"); + aq->regs = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(aq->regs)) { + dev_err(&pdev->dev, "missing registers\n"); + err = PTR_ERR(aq->regs); + goto exit; + } + + /* Map the AHB memory */ + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "qspi_mmap"); + aq->mem = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(aq->mem)) { + dev_err(&pdev->dev, "missing AHB memory\n"); + err = PTR_ERR(aq->mem); + goto exit; + } + + /* Get the peripheral clock */ + aq->clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(aq->clk)) { + dev_err(&pdev->dev, "missing peripheral clock\n"); + err = PTR_ERR(aq->clk); + goto exit; + } + + /* Enable the peripheral clock */ + err = clk_prepare_enable(aq->clk); + if (err) { + dev_err(&pdev->dev, "failed to enable the peripheral clock\n"); + goto exit; + } + + /* Request the IRQ */ + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + dev_err(&pdev->dev, "missing IRQ\n"); + err = irq; + goto disable_clk; + } + err = devm_request_irq(&pdev->dev, irq, atmel_qspi_interrupt, + 0, dev_name(&pdev->dev), aq); + if (err) + goto disable_clk; + + err = atmel_qspi_init(aq); + if (err) + goto disable_clk; + + err = spi_register_controller(ctrl); + if (err) + goto disable_clk; + + return 0; + +disable_clk: + clk_disable_unprepare(aq->clk); +exit: + spi_controller_put(ctrl); + + return err; +} + +static int atmel_qspi_remove(struct platform_device *pdev) +{ + struct spi_controller *ctrl = platform_get_drvdata(pdev); + struct atmel_qspi *aq = spi_controller_get_devdata(ctrl); + + spi_unregister_controller(ctrl); + qspi_writel(aq, QSPI_CR, QSPI_CR_QSPIDIS); + clk_disable_unprepare(aq->clk); + return 0; +} + +static int __maybe_unused atmel_qspi_suspend(struct device *dev) +{ + struct atmel_qspi *aq = dev_get_drvdata(dev); + + clk_disable_unprepare(aq->clk); + + return 0; +} + +static int __maybe_unused atmel_qspi_resume(struct device *dev) +{ + struct atmel_qspi *aq = dev_get_drvdata(dev); + + clk_prepare_enable(aq->clk); + + return atmel_qspi_init(aq); +} + +static SIMPLE_DEV_PM_OPS(atmel_qspi_pm_ops, atmel_qspi_suspend, + atmel_qspi_resume); + +static const struct of_device_id atmel_qspi_dt_ids[] = { + { .compatible = "atmel,sama5d2-qspi" }, + { /* sentinel */ } +}; + +MODULE_DEVICE_TABLE(of, atmel_qspi_dt_ids); + +static struct platform_driver atmel_qspi_driver = { + .driver = { + .name = "atmel_qspi", + .of_match_table = atmel_qspi_dt_ids, + .pm = &atmel_qspi_pm_ops, + }, + .probe = atmel_qspi_probe, + .remove = atmel_qspi_remove, +}; +module_platform_driver(atmel_qspi_driver); + +MODULE_AUTHOR("Cyrille Pitchen <cyrille.pitchen@atmel.com>"); +MODULE_AUTHOR("Piotr Bugalski <bugalski.piotr@gmail.com"); +MODULE_DESCRIPTION("Atmel QSPI Controller driver"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/spi/spi-mem.c b/drivers/spi/spi-mem.c index 5e15d62775e9..5217a5628be2 100644 --- a/drivers/spi/spi-mem.c +++ b/drivers/spi/spi-mem.c @@ -149,7 +149,7 @@ static bool spi_mem_default_supports_op(struct spi_mem *mem, spi_check_buswidth_req(mem, op->dummy.buswidth, true)) return false; - if (op->data.nbytes && + if (op->data.dir != SPI_MEM_NO_DATA && spi_check_buswidth_req(mem, op->data.buswidth, op->data.dir == SPI_MEM_DATA_OUT)) return false; @@ -220,6 +220,44 @@ bool spi_mem_supports_op(struct spi_mem *mem, const struct spi_mem_op *op) } EXPORT_SYMBOL_GPL(spi_mem_supports_op); +static int spi_mem_access_start(struct spi_mem *mem) +{ + struct spi_controller *ctlr = mem->spi->controller; + + /* + * Flush the message queue before executing our SPI memory + * operation to prevent preemption of regular SPI transfers. + */ + spi_flush_queue(ctlr); + + if (ctlr->auto_runtime_pm) { + int ret; + + ret = pm_runtime_get_sync(ctlr->dev.parent); + if (ret < 0) { + dev_err(&ctlr->dev, "Failed to power device: %d\n", + ret); + return ret; + } + } + + mutex_lock(&ctlr->bus_lock_mutex); + mutex_lock(&ctlr->io_mutex); + + return 0; +} + +static void spi_mem_access_end(struct spi_mem *mem) +{ + struct spi_controller *ctlr = mem->spi->controller; + + mutex_unlock(&ctlr->io_mutex); + mutex_unlock(&ctlr->bus_lock_mutex); + + if (ctlr->auto_runtime_pm) + pm_runtime_put(ctlr->dev.parent); +} + /** * spi_mem_exec_op() - Execute a memory operation * @mem: the SPI memory @@ -249,30 +287,13 @@ int spi_mem_exec_op(struct spi_mem *mem, const struct spi_mem_op *op) return -ENOTSUPP; if (ctlr->mem_ops) { - /* - * Flush the message queue before executing our SPI memory - * operation to prevent preemption of regular SPI transfers. - */ - spi_flush_queue(ctlr); - - if (ctlr->auto_runtime_pm) { - ret = pm_runtime_get_sync(ctlr->dev.parent); - if (ret < 0) { - dev_err(&ctlr->dev, - "Failed to power device: %d\n", - ret); - return ret; - } - } + ret = spi_mem_access_start(mem); + if (ret) + return ret; - mutex_lock(&ctlr->bus_lock_mutex); - mutex_lock(&ctlr->io_mutex); ret = ctlr->mem_ops->exec_op(mem, op); - mutex_unlock(&ctlr->io_mutex); - mutex_unlock(&ctlr->bus_lock_mutex); - if (ctlr->auto_runtime_pm) - pm_runtime_put(ctlr->dev.parent); + spi_mem_access_end(mem); /* * Some controllers only optimize specific paths (typically the @@ -418,6 +439,210 @@ int spi_mem_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op) } EXPORT_SYMBOL_GPL(spi_mem_adjust_op_size); +static ssize_t spi_mem_no_dirmap_read(struct spi_mem_dirmap_desc *desc, + u64 offs, size_t len, void *buf) +{ + struct spi_mem_op op = desc->info.op_tmpl; + int ret; + + op.addr.val = desc->info.offset + offs; + op.data.buf.in = buf; + op.data.nbytes = len; + ret = spi_mem_adjust_op_size(desc->mem, &op); + if (ret) + return ret; + + ret = spi_mem_exec_op(desc->mem, &op); + if (ret) + return ret; + + return op.data.nbytes; +} + +static ssize_t spi_mem_no_dirmap_write(struct spi_mem_dirmap_desc *desc, + u64 offs, size_t len, const void *buf) +{ + struct spi_mem_op op = desc->info.op_tmpl; + int ret; + + op.addr.val = desc->info.offset + offs; + op.data.buf.out = buf; + op.data.nbytes = len; + ret = spi_mem_adjust_op_size(desc->mem, &op); + if (ret) + return ret; + + ret = spi_mem_exec_op(desc->mem, &op); + if (ret) + return ret; + + return op.data.nbytes; +} + +/** + * spi_mem_dirmap_create() - Create a direct mapping descriptor + * @mem: SPI mem device this direct mapping should be created for + * @info: direct mapping information + * + * This function is creating a direct mapping descriptor which can then be used + * to access the memory using spi_mem_dirmap_read() or spi_mem_dirmap_write(). + * If the SPI controller driver does not support direct mapping, this function + * fallback to an implementation using spi_mem_exec_op(), so that the caller + * doesn't have to bother implementing a fallback on his own. + * + * Return: a valid pointer in case of success, and ERR_PTR() otherwise. + */ +struct spi_mem_dirmap_desc * +spi_mem_dirmap_create(struct spi_mem *mem, + const struct spi_mem_dirmap_info *info) +{ + struct spi_controller *ctlr = mem->spi->controller; + struct spi_mem_dirmap_desc *desc; + int ret = -ENOTSUPP; + + /* Make sure the number of address cycles is between 1 and 8 bytes. */ + if (!info->op_tmpl.addr.nbytes || info->op_tmpl.addr.nbytes > 8) + return ERR_PTR(-EINVAL); + + /* data.dir should either be SPI_MEM_DATA_IN or SPI_MEM_DATA_OUT. */ + if (info->op_tmpl.data.dir == SPI_MEM_NO_DATA) + return ERR_PTR(-EINVAL); + + desc = kzalloc(sizeof(*desc), GFP_KERNEL); + if (!desc) + return ERR_PTR(-ENOMEM); + + desc->mem = mem; + desc->info = *info; + if (ctlr->mem_ops && ctlr->mem_ops->dirmap_create) + ret = ctlr->mem_ops->dirmap_create(desc); + + if (ret) { + desc->nodirmap = true; + if (!spi_mem_supports_op(desc->mem, &desc->info.op_tmpl)) + ret = -ENOTSUPP; + else + ret = 0; + } + + if (ret) { + kfree(desc); + return ERR_PTR(ret); + } + + return desc; +} +EXPORT_SYMBOL_GPL(spi_mem_dirmap_create); + +/** + * spi_mem_dirmap_destroy() - Destroy a direct mapping descriptor + * @desc: the direct mapping descriptor to destroy + * @info: direct mapping information + * + * This function destroys a direct mapping descriptor previously created by + * spi_mem_dirmap_create(). + */ +void spi_mem_dirmap_destroy(struct spi_mem_dirmap_desc *desc) +{ + struct spi_controller *ctlr = desc->mem->spi->controller; + + if (!desc->nodirmap && ctlr->mem_ops && ctlr->mem_ops->dirmap_destroy) + ctlr->mem_ops->dirmap_destroy(desc); +} +EXPORT_SYMBOL_GPL(spi_mem_dirmap_destroy); + +/** + * spi_mem_dirmap_dirmap_read() - Read data through a direct mapping + * @desc: direct mapping descriptor + * @offs: offset to start reading from. Note that this is not an absolute + * offset, but the offset within the direct mapping which already has + * its own offset + * @len: length in bytes + * @buf: destination buffer. This buffer must be DMA-able + * + * This function reads data from a memory device using a direct mapping + * previously instantiated with spi_mem_dirmap_create(). + * + * Return: the amount of data read from the memory device or a negative error + * code. Note that the returned size might be smaller than @len, and the caller + * is responsible for calling spi_mem_dirmap_read() again when that happens. + */ +ssize_t spi_mem_dirmap_read(struct spi_mem_dirmap_desc *desc, + u64 offs, size_t len, void *buf) +{ + struct spi_controller *ctlr = desc->mem->spi->controller; + ssize_t ret; + + if (desc->info.op_tmpl.data.dir != SPI_MEM_DATA_IN) + return -EINVAL; + + if (!len) + return 0; + + if (desc->nodirmap) { + ret = spi_mem_no_dirmap_read(desc, offs, len, buf); + } else if (ctlr->mem_ops && ctlr->mem_ops->dirmap_read) { + ret = spi_mem_access_start(desc->mem); + if (ret) + return ret; + + ret = ctlr->mem_ops->dirmap_read(desc, offs, len, buf); + + spi_mem_access_end(desc->mem); + } else { + ret = -ENOTSUPP; + } + + return ret; +} +EXPORT_SYMBOL_GPL(spi_mem_dirmap_read); + +/** + * spi_mem_dirmap_dirmap_write() - Write data through a direct mapping + * @desc: direct mapping descriptor + * @offs: offset to start writing from. Note that this is not an absolute + * offset, but the offset within the direct mapping which already has + * its own offset + * @len: length in bytes + * @buf: source buffer. This buffer must be DMA-able + * + * This function writes data to a memory device using a direct mapping + * previously instantiated with spi_mem_dirmap_create(). + * + * Return: the amount of data written to the memory device or a negative error + * code. Note that the returned size might be smaller than @len, and the caller + * is responsible for calling spi_mem_dirmap_write() again when that happens. + */ +ssize_t spi_mem_dirmap_write(struct spi_mem_dirmap_desc *desc, + u64 offs, size_t len, const void *buf) +{ + struct spi_controller *ctlr = desc->mem->spi->controller; + ssize_t ret; + + if (desc->info.op_tmpl.data.dir != SPI_MEM_DATA_OUT) + return -EINVAL; + + if (!len) + return 0; + + if (desc->nodirmap) { + ret = spi_mem_no_dirmap_write(desc, offs, len, buf); + } else if (ctlr->mem_ops && ctlr->mem_ops->dirmap_write) { + ret = spi_mem_access_start(desc->mem); + if (ret) + return ret; + + ret = ctlr->mem_ops->dirmap_write(desc, offs, len, buf); + + spi_mem_access_end(desc->mem); + } else { + ret = -ENOTSUPP; + } + + return ret; +} +EXPORT_SYMBOL_GPL(spi_mem_dirmap_write); + static inline struct spi_mem_driver *to_spi_mem_drv(struct device_driver *drv) { return container_of(drv, struct spi_mem_driver, spidrv.driver); |