diff options
Diffstat (limited to 'drivers/usb/serial/cp210x.c')
| -rw-r--r-- | drivers/usb/serial/cp210x.c | 82 |
1 files changed, 78 insertions, 4 deletions
diff --git a/drivers/usb/serial/cp210x.c b/drivers/usb/serial/cp210x.c index 336a3c0f9f2c..260c875dd263 100644 --- a/drivers/usb/serial/cp210x.c +++ b/drivers/usb/serial/cp210x.c @@ -443,10 +443,10 @@ struct cp210x_pin_mode { #define CP210X_PIN_MODE_GPIO BIT(0) /* - * CP210X_VENDOR_SPECIFIC, CP210X_GET_PORTCONFIG call reads these 0xf bytes. - * Structure needs padding due to unused/unspecified bytes. + * CP210X_VENDOR_SPECIFIC, CP210X_GET_PORTCONFIG call reads these 0xf bytes + * on a CP2105 chip. Structure needs padding due to unused/unspecified bytes. */ -struct cp210x_config { +struct cp210x_dual_port_config { __le16 gpio_mode; u8 __pad0[2]; __le16 reset_state; @@ -457,6 +457,19 @@ struct cp210x_config { u8 device_cfg; } __packed; +/* + * CP210X_VENDOR_SPECIFIC, CP210X_GET_PORTCONFIG call reads these 0xd bytes + * on a CP2104 chip. Structure needs padding due to unused/unspecified bytes. + */ +struct cp210x_single_port_config { + __le16 gpio_mode; + u8 __pad0[2]; + __le16 reset_state; + u8 __pad1[4]; + __le16 suspend_state; + u8 device_cfg; +} __packed; + /* GPIO modes */ #define CP210X_SCI_GPIO_MODE_OFFSET 9 #define CP210X_SCI_GPIO_MODE_MASK GENMASK(11, 9) @@ -464,11 +477,19 @@ struct cp210x_config { #define CP210X_ECI_GPIO_MODE_OFFSET 2 #define CP210X_ECI_GPIO_MODE_MASK GENMASK(3, 2) +#define CP210X_GPIO_MODE_OFFSET 8 +#define CP210X_GPIO_MODE_MASK GENMASK(11, 8) + /* CP2105 port configuration values */ #define CP2105_GPIO0_TXLED_MODE BIT(0) #define CP2105_GPIO1_RXLED_MODE BIT(1) #define CP2105_GPIO1_RS485_MODE BIT(2) +/* CP2104 port configuration values */ +#define CP2104_GPIO0_TXLED_MODE BIT(0) +#define CP2104_GPIO1_RXLED_MODE BIT(1) +#define CP2104_GPIO2_RS485_MODE BIT(2) + /* CP2102N configuration array indices */ #define CP210X_2NCONFIG_CONFIG_VERSION_IDX 2 #define CP210X_2NCONFIG_GPIO_MODE_IDX 581 @@ -1470,7 +1491,7 @@ static int cp2105_gpioconf_init(struct usb_serial *serial) { struct cp210x_serial_private *priv = usb_get_serial_data(serial); struct cp210x_pin_mode mode; - struct cp210x_config config; + struct cp210x_dual_port_config config; u8 intf_num = cp210x_interface_num(serial); u8 iface_config; int result; @@ -1529,6 +1550,56 @@ static int cp2105_gpioconf_init(struct usb_serial *serial) return 0; } +static int cp2104_gpioconf_init(struct usb_serial *serial) +{ + struct cp210x_serial_private *priv = usb_get_serial_data(serial); + struct cp210x_single_port_config config; + u8 iface_config; + u8 gpio_latch; + int result; + u8 i; + + result = cp210x_read_vendor_block(serial, REQTYPE_DEVICE_TO_HOST, + CP210X_GET_PORTCONFIG, &config, + sizeof(config)); + if (result < 0) + return result; + + priv->gc.ngpio = 4; + + iface_config = config.device_cfg; + priv->gpio_pushpull = (u8)((le16_to_cpu(config.gpio_mode) & + CP210X_GPIO_MODE_MASK) >> + CP210X_GPIO_MODE_OFFSET); + gpio_latch = (u8)((le16_to_cpu(config.reset_state) & + CP210X_GPIO_MODE_MASK) >> + CP210X_GPIO_MODE_OFFSET); + + /* mark all pins which are not in GPIO mode */ + if (iface_config & CP2104_GPIO0_TXLED_MODE) /* GPIO 0 */ + priv->gpio_altfunc |= BIT(0); + if (iface_config & CP2104_GPIO1_RXLED_MODE) /* GPIO 1 */ + priv->gpio_altfunc |= BIT(1); + if (iface_config & CP2104_GPIO2_RS485_MODE) /* GPIO 2 */ + priv->gpio_altfunc |= BIT(2); + + /* + * Like CP2102N, CP2104 has also no strict input and output pin + * modes. + * Do the same input mode emulation as CP2102N. + */ + for (i = 0; i < priv->gc.ngpio; ++i) { + /* + * Set direction to "input" iff pin is open-drain and reset + * value is 1. + */ + if (!(priv->gpio_pushpull & BIT(i)) && (gpio_latch & BIT(i))) + priv->gpio_input |= BIT(i); + } + + return 0; +} + static int cp2102n_gpioconf_init(struct usb_serial *serial) { struct cp210x_serial_private *priv = usb_get_serial_data(serial); @@ -1627,6 +1698,9 @@ static int cp210x_gpio_init(struct usb_serial *serial) int result; switch (priv->partnum) { + case CP210X_PARTNUM_CP2104: + result = cp2104_gpioconf_init(serial); + break; case CP210X_PARTNUM_CP2105: result = cp2105_gpioconf_init(serial); break; |