diff options
Diffstat (limited to 'drivers/usb/storage/scsiglue.c')
| -rw-r--r-- | drivers/usb/storage/scsiglue.c | 53 |
1 files changed, 28 insertions, 25 deletions
diff --git a/drivers/usb/storage/scsiglue.c b/drivers/usb/storage/scsiglue.c index 3fcde9f0fa5f..09779f6a8179 100644 --- a/drivers/usb/storage/scsiglue.c +++ b/drivers/usb/storage/scsiglue.c @@ -1,8 +1,6 @@ /* Driver for USB Mass Storage compliant devices * SCSI layer glue code * - * $Id: scsiglue.c,v 1.26 2002/04/22 03:39:43 mdharm Exp $ - * * Current development and maintenance by: * (c) 1999-2002 Matthew Dharm (mdharm-usb@one-eyed-alien.net) * @@ -73,7 +71,6 @@ static const char* host_info(struct Scsi_Host *host) static int slave_alloc (struct scsi_device *sdev) { struct us_data *us = host_to_us(sdev->host); - struct usb_host_endpoint *bulk_in_ep; /* * Set the INQUIRY transfer length to 36. We don't use any of @@ -82,16 +79,22 @@ static int slave_alloc (struct scsi_device *sdev) */ sdev->inquiry_len = 36; - /* Scatter-gather buffers (all but the last) must have a length - * divisible by the bulk maxpacket size. Otherwise a data packet - * would end up being short, causing a premature end to the data - * transfer. We'll use the maxpacket value of the bulk-IN pipe - * to set the SCSI device queue's DMA alignment mask. + /* USB has unusual DMA-alignment requirements: Although the + * starting address of each scatter-gather element doesn't matter, + * the length of each element except the last must be divisible + * by the Bulk maxpacket value. There's currently no way to + * express this by block-layer constraints, so we'll cop out + * and simply require addresses to be aligned at 512-byte + * boundaries. This is okay since most block I/O involves + * hardware sectors that are multiples of 512 bytes in length, + * and since host controllers up through USB 2.0 have maxpacket + * values no larger than 512. + * + * But it doesn't suffice for Wireless USB, where Bulk maxpacket + * values can be as large as 2048. To make that work properly + * will require changes to the block layer. */ - bulk_in_ep = us->pusb_dev->ep_in[usb_pipeendpoint(us->recv_bulk_pipe)]; - blk_queue_update_dma_alignment(sdev->request_queue, - le16_to_cpu(bulk_in_ep->desc.wMaxPacketSize) - 1); - /* wMaxPacketSize must be a power of 2 */ + blk_queue_update_dma_alignment(sdev->request_queue, (512 - 1)); /* * The UFI spec treates the Peripheral Qualifier bits in an @@ -116,10 +119,10 @@ static int slave_configure(struct scsi_device *sdev) * while others have trouble with more than 64K. At this time we * are limiting both to 32K (64 sectores). */ - if (us->flags & (US_FL_MAX_SECTORS_64 | US_FL_MAX_SECTORS_MIN)) { + if (us->fflags & (US_FL_MAX_SECTORS_64 | US_FL_MAX_SECTORS_MIN)) { unsigned int max_sectors = 64; - if (us->flags & US_FL_MAX_SECTORS_MIN) + if (us->fflags & US_FL_MAX_SECTORS_MIN) max_sectors = PAGE_CACHE_SIZE >> 9; if (sdev->request_queue->max_sectors > max_sectors) blk_queue_max_sectors(sdev->request_queue, @@ -148,7 +151,7 @@ static int slave_configure(struct scsi_device *sdev) * majority of devices work fine, but a few still can't * handle it. The sd driver will simply assume those * devices are write-enabled. */ - if (us->flags & US_FL_NO_WP_DETECT) + if (us->fflags & US_FL_NO_WP_DETECT) sdev->skip_ms_page_3f = 1; /* A number of devices have problems with MODE SENSE for @@ -158,13 +161,13 @@ static int slave_configure(struct scsi_device *sdev) /* Some disks return the total number of blocks in response * to READ CAPACITY rather than the highest block number. * If this device makes that mistake, tell the sd driver. */ - if (us->flags & US_FL_FIX_CAPACITY) + if (us->fflags & US_FL_FIX_CAPACITY) sdev->fix_capacity = 1; /* A few disks have two indistinguishable version, one of * which reports the correct capacity and the other does not. * The sd driver has to guess which is the case. */ - if (us->flags & US_FL_CAPACITY_HEURISTICS) + if (us->fflags & US_FL_CAPACITY_HEURISTICS) sdev->guess_capacity = 1; /* Some devices report a SCSI revision level above 2 but are @@ -213,7 +216,7 @@ static int slave_configure(struct scsi_device *sdev) /* Some devices choke when they receive a PREVENT-ALLOW MEDIUM * REMOVAL command, so suppress those commands. */ - if (us->flags & US_FL_NOT_LOCKABLE) + if (us->fflags & US_FL_NOT_LOCKABLE) sdev->lockable = 0; /* this is to satisfy the compiler, tho I don't think the @@ -238,7 +241,7 @@ static int queuecommand(struct scsi_cmnd *srb, } /* fail the command if we are disconnecting */ - if (test_bit(US_FLIDX_DISCONNECTING, &us->flags)) { + if (test_bit(US_FLIDX_DISCONNECTING, &us->dflags)) { US_DEBUGP("Fail command during disconnect\n"); srb->result = DID_NO_CONNECT << 16; done(srb); @@ -248,7 +251,7 @@ static int queuecommand(struct scsi_cmnd *srb, /* enqueue the command and wake up the control thread */ srb->scsi_done = done; us->srb = srb; - up(&(us->sema)); + complete(&us->cmnd_ready); return 0; } @@ -280,9 +283,9 @@ static int command_abort(struct scsi_cmnd *srb) * with the reset). Note that we must retain the host lock while * calling usb_stor_stop_transport(); otherwise it might interfere * with an auto-reset that begins as soon as we release the lock. */ - set_bit(US_FLIDX_TIMED_OUT, &us->flags); - if (!test_bit(US_FLIDX_RESETTING, &us->flags)) { - set_bit(US_FLIDX_ABORTING, &us->flags); + set_bit(US_FLIDX_TIMED_OUT, &us->dflags); + if (!test_bit(US_FLIDX_RESETTING, &us->dflags)) { + set_bit(US_FLIDX_ABORTING, &us->dflags); usb_stor_stop_transport(us); } scsi_unlock(us_to_host(us)); @@ -329,7 +332,7 @@ void usb_stor_report_device_reset(struct us_data *us) struct Scsi_Host *host = us_to_host(us); scsi_report_device_reset(host, 0, 0); - if (us->flags & US_FL_SCM_MULT_TARG) { + if (us->fflags & US_FL_SCM_MULT_TARG) { for (i = 1; i < host->max_id; ++i) scsi_report_device_reset(host, 0, i); } @@ -400,7 +403,7 @@ static int proc_info (struct Scsi_Host *host, char *buffer, pos += sprintf(pos, " Quirks:"); #define US_FLAG(name, value) \ - if (us->flags & value) pos += sprintf(pos, " " #name); + if (us->fflags & value) pos += sprintf(pos, " " #name); US_DO_ALL_FLAGS #undef US_FLAG |