diff options
Diffstat (limited to 'drivers/usb')
| -rw-r--r-- | drivers/usb/dwc3/gadget.c | 29 |
1 files changed, 19 insertions, 10 deletions
diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c index 2b53194081ba..679c12e14522 100644 --- a/drivers/usb/dwc3/gadget.c +++ b/drivers/usb/dwc3/gadget.c @@ -270,27 +270,36 @@ int dwc3_send_gadget_ep_cmd(struct dwc3_ep *dep, unsigned cmd, const struct usb_endpoint_descriptor *desc = dep->endpoint.desc; struct dwc3 *dwc = dep->dwc; u32 timeout = 1000; + u32 saved_config = 0; u32 reg; int cmd_status = 0; - int susphy = false; int ret = -EINVAL; /* - * Synopsys Databook 2.60a states, on section 6.3.2.5.[1-8], that if - * we're issuing an endpoint command, we must check if - * GUSB2PHYCFG.SUSPHY bit is set. If it is, then we need to clear it. + * When operating in USB 2.0 speeds (HS/FS), if GUSB2PHYCFG.ENBLSLPM or + * GUSB2PHYCFG.SUSPHY is set, it must be cleared before issuing an + * endpoint command. * - * We will also set SUSPHY bit to what it was before returning as stated - * by the same section on Synopsys databook. + * Save and clear both GUSB2PHYCFG.ENBLSLPM and GUSB2PHYCFG.SUSPHY + * settings. Restore them after the command is completed. + * + * DWC_usb3 3.30a and DWC_usb31 1.90a programming guide section 3.2.2 */ if (dwc->gadget.speed <= USB_SPEED_HIGH) { reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0)); if (unlikely(reg & DWC3_GUSB2PHYCFG_SUSPHY)) { - susphy = true; + saved_config |= DWC3_GUSB2PHYCFG_SUSPHY; reg &= ~DWC3_GUSB2PHYCFG_SUSPHY; - dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg); } + + if (reg & DWC3_GUSB2PHYCFG_ENBLSLPM) { + saved_config |= DWC3_GUSB2PHYCFG_ENBLSLPM; + reg &= ~DWC3_GUSB2PHYCFG_ENBLSLPM; + } + + if (saved_config) + dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg); } if (DWC3_DEPCMD_CMD(cmd) == DWC3_DEPCMD_STARTTRANSFER) { @@ -389,9 +398,9 @@ int dwc3_send_gadget_ep_cmd(struct dwc3_ep *dep, unsigned cmd, } } - if (unlikely(susphy)) { + if (saved_config) { reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0)); - reg |= DWC3_GUSB2PHYCFG_SUSPHY; + reg |= saved_config; dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg); } |