diff options
Diffstat (limited to 'include/linux/iio/gyro/itg3200.h')
| -rw-r--r-- | include/linux/iio/gyro/itg3200.h | 154 |
1 files changed, 154 insertions, 0 deletions
diff --git a/include/linux/iio/gyro/itg3200.h b/include/linux/iio/gyro/itg3200.h new file mode 100644 index 000000000000..c53f16914b77 --- /dev/null +++ b/include/linux/iio/gyro/itg3200.h @@ -0,0 +1,154 @@ +/* + * itg3200.h -- support InvenSense ITG3200 + * Digital 3-Axis Gyroscope driver + * + * Copyright (c) 2011 Christian Strobel <christian.strobel@iis.fraunhofer.de> + * Copyright (c) 2011 Manuel Stahl <manuel.stahl@iis.fraunhofer.de> + * Copyright (c) 2012 Thorsten Nowak <thorsten.nowak@iis.fraunhofer.de> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef I2C_ITG3200_H_ +#define I2C_ITG3200_H_ + +#include <linux/iio/iio.h> + +/* Register with I2C address (34h) */ +#define ITG3200_REG_ADDRESS 0x00 + +/* Sample rate divider + * Range: 0 to 255 + * Default value: 0x00 */ +#define ITG3200_REG_SAMPLE_RATE_DIV 0x15 + +/* Digital low pass filter settings */ +#define ITG3200_REG_DLPF 0x16 +/* DLPF full scale range */ +#define ITG3200_DLPF_FS_SEL_2000 0x18 +/* Bandwidth (Hz) and internal sample rate + * (kHz) of DLPF */ +#define ITG3200_DLPF_256_8 0x00 +#define ITG3200_DLPF_188_1 0x01 +#define ITG3200_DLPF_98_1 0x02 +#define ITG3200_DLPF_42_1 0x03 +#define ITG3200_DLPF_20_1 0x04 +#define ITG3200_DLPF_10_1 0x05 +#define ITG3200_DLPF_5_1 0x06 + +#define ITG3200_DLPF_CFG_MASK 0x07 + +/* Configuration for interrupt operations */ +#define ITG3200_REG_IRQ_CONFIG 0x17 +/* Logic level */ +#define ITG3200_IRQ_ACTIVE_LOW 0x80 +#define ITG3200_IRQ_ACTIVE_HIGH 0x00 +/* Drive type */ +#define ITG3200_IRQ_OPEN_DRAIN 0x40 +#define ITG3200_IRQ_PUSH_PULL 0x00 +/* Latch mode */ +#define ITG3200_IRQ_LATCH_UNTIL_CLEARED 0x20 +#define ITG3200_IRQ_LATCH_50US_PULSE 0x00 +/* Latch clear method */ +#define ITG3200_IRQ_LATCH_CLEAR_ANY 0x10 +#define ITG3200_IRQ_LATCH_CLEAR_STATUS 0x00 +/* Enable interrupt when device is ready */ +#define ITG3200_IRQ_DEVICE_RDY_ENABLE 0x04 +/* Enable interrupt when data is available */ +#define ITG3200_IRQ_DATA_RDY_ENABLE 0x01 + +/* Determine the status of ITG-3200 interrupts */ +#define ITG3200_REG_IRQ_STATUS 0x1A +/* Status of 'device is ready'-interrupt */ +#define ITG3200_IRQ_DEVICE_RDY_STATUS 0x04 +/* Status of 'data is available'-interrupt */ +#define ITG3200_IRQ_DATA_RDY_STATUS 0x01 + +/* Sensor registers */ +#define ITG3200_REG_TEMP_OUT_H 0x1B +#define ITG3200_REG_TEMP_OUT_L 0x1C +#define ITG3200_REG_GYRO_XOUT_H 0x1D +#define ITG3200_REG_GYRO_XOUT_L 0x1E +#define ITG3200_REG_GYRO_YOUT_H 0x1F +#define ITG3200_REG_GYRO_YOUT_L 0x20 +#define ITG3200_REG_GYRO_ZOUT_H 0x21 +#define ITG3200_REG_GYRO_ZOUT_L 0x22 + +/* Power management */ +#define ITG3200_REG_POWER_MANAGEMENT 0x3E +/* Reset device and internal registers to the + * power-up-default settings */ +#define ITG3200_RESET 0x80 +/* Enable low power sleep mode */ +#define ITG3200_SLEEP 0x40 +/* Put according gyroscope in standby mode */ +#define ITG3200_STANDBY_GYRO_X 0x20 +#define ITG3200_STANDBY_GYRO_Y 0x10 +#define ITG3200_STANDBY_GYRO_Z 0x08 +/* Determine the device clock source */ +#define ITG3200_CLK_INTERNAL 0x00 +#define ITG3200_CLK_GYRO_X 0x01 +#define ITG3200_CLK_GYRO_Y 0x02 +#define ITG3200_CLK_GYRO_Z 0x03 +#define ITG3200_CLK_EXT_32K 0x04 +#define ITG3200_CLK_EXT_19M 0x05 + + +/** + * struct itg3200 - device instance specific data + * @i2c: actual i2c_client + * @trig: data ready trigger from itg3200 pin + **/ +struct itg3200 { + struct i2c_client *i2c; + struct iio_trigger *trig; +}; + +enum ITG3200_SCAN_INDEX { + ITG3200_SCAN_TEMP, + ITG3200_SCAN_GYRO_X, + ITG3200_SCAN_GYRO_Y, + ITG3200_SCAN_GYRO_Z, + ITG3200_SCAN_ELEMENTS, +}; + +int itg3200_write_reg_8(struct iio_dev *indio_dev, + u8 reg_address, u8 val); + +int itg3200_read_reg_8(struct iio_dev *indio_dev, + u8 reg_address, u8 *val); + + +#ifdef CONFIG_IIO_BUFFER + +void itg3200_remove_trigger(struct iio_dev *indio_dev); +int itg3200_probe_trigger(struct iio_dev *indio_dev); + +int itg3200_buffer_configure(struct iio_dev *indio_dev); +void itg3200_buffer_unconfigure(struct iio_dev *indio_dev); + +#else /* CONFIG_IIO_BUFFER */ + +static inline void itg3200_remove_trigger(struct iio_dev *indio_dev) +{ +} + +static inline int itg3200_probe_trigger(struct iio_dev *indio_dev) +{ + return 0; +} + +static inline int itg3200_buffer_configure(struct iio_dev *indio_dev) +{ + return 0; +} + +static inline void itg3200_buffer_unconfigure(struct iio_dev *indio_dev) +{ +} + +#endif /* CONFIG_IIO_RING_BUFFER */ + +#endif /* ITG3200_H_ */ |