1 files changed, 98 insertions, 0 deletions
diff --git a/include/linux/usb/musb.h b/include/linux/usb/musb.h
new file mode 100644
index 000000000000..630962c04ca4
--- /dev/null
+++ b/include/linux/usb/musb.h
@@ -0,0 +1,98 @@
+/*
+ * This is used to for host and peripheral modes of the driver for
+ * Inventra (Multidrop) Highspeed Dual-Role Controllers:  (M)HDRC.
+ *
+ * Board initialization should put one of these into dev->platform_data,
+ * probably on some platform_device named "musb_hdrc".  It encapsulates
+ * key configuration differences between boards.
+ */
+
+/* The USB role is defined by the connector used on the board, so long as
+ * standards are being followed.  (Developer boards sometimes won't.)
+ */
+enum musb_mode {
+	MUSB_UNDEFINED = 0,
+	MUSB_HOST,		/* A or Mini-A connector */
+	MUSB_PERIPHERAL,	/* B or Mini-B connector */
+	MUSB_OTG		/* Mini-AB connector */
+};
+
+struct clk;
+
+struct musb_hdrc_eps_bits {
+	const char	name[16];
+	u8		bits;
+};
+
+struct musb_hdrc_config {
+	/* MUSB configuration-specific details */
+	unsigned	multipoint:1;	/* multipoint device */
+	unsigned	dyn_fifo:1;	/* supports dynamic fifo sizing */
+	unsigned	soft_con:1;	/* soft connect required */
+	unsigned	utm_16:1;	/* utm data witdh is 16 bits */
+	unsigned	big_endian:1;	/* true if CPU uses big-endian */
+	unsigned	mult_bulk_tx:1;	/* Tx ep required for multbulk pkts */
+	unsigned	mult_bulk_rx:1;	/* Rx ep required for multbulk pkts */
+	unsigned	high_iso_tx:1;	/* Tx ep required for HB iso */
+	unsigned	high_iso_rx:1;	/* Rx ep required for HD iso */
+	unsigned	dma:1;		/* supports DMA */
+	unsigned	vendor_req:1;	/* vendor registers required */
+
+	u8		num_eps;	/* number of endpoints _with_ ep0 */
+	u8		dma_channels;	/* number of dma channels */
+	u8		dyn_fifo_size;	/* dynamic size in bytes */
+	u8		vendor_ctrl;	/* vendor control reg width */
+	u8		vendor_stat;	/* vendor status reg witdh */
+	u8		dma_req_chan;	/* bitmask for required dma channels */
+	u8		ram_bits;	/* ram address size */
+
+	struct musb_hdrc_eps_bits *eps_bits;
+};
+
+struct musb_hdrc_platform_data {
+	/* MUSB_HOST, MUSB_PERIPHERAL, or MUSB_OTG */
+	u8		mode;
+
+	/* for clk_get() */
+	const char	*clock;
+
+	/* (HOST or OTG) switch VBUS on/off */
+	int		(*set_vbus)(struct device *dev, int is_on);
+
+	/* (HOST or OTG) mA/2 power supplied on (default = 8mA) */
+	u8		power;
+
+	/* (PERIPHERAL) mA/2 max power consumed (default = 100mA) */
+	u8		min_power;
+
+	/* (HOST or OTG) msec/2 after VBUS on till power good */
+	u8		potpgt;
+
+	/* Power the device on or off */
+	int		(*set_power)(int state);
+
+	/* Turn device clock on or off */
+	int		(*set_clock)(struct clk *clock, int is_on);
+
+	/* MUSB configuration-specific details */
+	struct musb_hdrc_config	*config;
+};
+
+
+/* TUSB 6010 support */
+
+#define	TUSB6010_OSCCLK_60	16667	/* psec/clk @ 60.0 MHz */
+#define	TUSB6010_REFCLK_24	41667	/* psec/clk @ 24.0 MHz XI */
+#define	TUSB6010_REFCLK_19	52083	/* psec/clk @ 19.2 MHz CLKIN */
+
+#ifdef	CONFIG_ARCH_OMAP2
+
+extern int __init tusb6010_setup_interface(
+		struct musb_hdrc_platform_data *data,
+		unsigned ps_refclk, unsigned waitpin,
+		unsigned async_cs, unsigned sync_cs,
+		unsigned irq, unsigned dmachan);
+
+extern int tusb6010_platform_retime(unsigned is_refclk);
+
+#endif	/* OMAP2 */