| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform removals from Arnd Bergmann:
"There are a lot of platforms that have not seen any interesting code
changes in the past five years or more.
I made a list and asked around which ones are no longer in use, and
received confirmation about six ARM platforms and the TI C6x
architecture that have all reached the end of their life upstream,
with no known users remaining:
- efm32 - added in 2011, first Cortex-M, no notable changes after 2013
- picoxcell - added in 2011, abandoned after 2012 acquisition
- prima2 - added in 20111, no notable changes since 2015
- tango - added in 2015, sporadic changes until 2017, but abandoned
- u300 - added in 2009, no notable changes since 2013
- zx - added in 2015 for both 32, 2017 for 64 bit, no notable changes
- arch/c6x - added in 2011, but work stalled soon after that
A number of other platforms on the original list turned out to still
have users. In some cases there are out-of-tree patches and users that
plan to contribute them in the future, in other cases the code is
complete and works reliably"
Link: https://lore.kernel.org/lkml/CAK8P3a2DZ8xQp7R=H=wewHnT2=a_=M53QsZOueMVEf7tOZLKNg@mail.gmail.com/
* tag 'arm-platform-removal-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: remove u300 platform
ARM: remove tango platform
ARM: remove zte zx platform
ARM: remove sirf prima2/atlas platforms
c6x: remove architecture
MAINTAINERS: Remove deleted platform efm32
ARM: drop efm32 platform
ARM: Remove PicoXcell platform support
ARM: dts: Remove PicoXcell platforms
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"There are only two left-over remaining non-urgent ARM SoC bug fixes:
- A build fix for the Atmel SAM9 platform to allow building with the
clang integrated assembler
- A DT fix for ethernet on Intel SoCFPGA, this has been broken since
it was added in v5.4"
* tag 'arm-fixes-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: at91: use proper asm syntax in pm_suspend
arm64: dts: agilex: fix phy interface bit shift for gmac1 and gmac2
|
|
Pull networking updates from David Miller:
"Here is what we have this merge window:
1) Support SW steering for mlx5 Connect-X6Dx, from Yevgeny Kliteynik.
2) Add RSS multi group support to octeontx2-pf driver, from Geetha
Sowjanya.
3) Add support for KS8851 PHY. From Marek Vasut.
4) Add support for GarfieldPeak bluetooth controller from Kiran K.
5) Add support for half-duplex tcan4x5x can controllers.
6) Add batch skb rx processing to bcrm63xx_enet, from Sieng Piaw
Liew.
7) Rework RX port offload infrastructure, particularly wrt, UDP
tunneling, from Jakub Kicinski.
8) Add BCM72116 PHY support, from Florian Fainelli.
9) Remove Dsa specific notifiers, they are unnecessary. From Vladimir
Oltean.
10) Add support for picosecond rx delay in dwmac-meson8b chips. From
Martin Blumenstingl.
11) Support TSO on xfrm interfaces from Eyal Birger.
12) Add support for MP_PRIO to mptcp stack, from Geliang Tang.
13) Support BCM4908 integrated switch, from Rafał Miłecki.
14) Support for directly accessing kernel module variables via module
BTF info, from Andrii Naryiko.
15) Add DASH (esktop and mobile Architecture for System Hardware)
support to r8169 driver, from Heiner Kallweit.
16) Add rx vlan filtering to dpaa2-eth, from Ionut-robert Aron.
17) Add support for 100 base0x SFP devices, from Bjarni Jonasson.
18) Support link aggregation in DSA, from Tobias Waldekranz.
19) Support for bitwidse atomics in bpf, from Brendan Jackman.
20) SmartEEE support in at803x driver, from Russell King.
21) Add support for flow based tunneling to GTP, from Pravin B Shelar.
22) Allow arbitrary number of interconnrcts in ipa, from Alex Elder.
23) TLS RX offload for bonding, from Tariq Toukan.
24) RX decap offklload support in mac80211, from Felix Fietkou.
25) devlink health saupport in octeontx2-af, from George Cherian.
26) Add TTL attr to SCM_TIMESTAMP_OPT_STATS, from Yousuk Seung
27) Delegated actionss support in mptcp, from Paolo Abeni.
28) Support receive timestamping when doin zerocopy tcp receive. From
Arjun Ray.
29) HTB offload support for mlx5, from Maxim Mikityanskiy.
30) UDP GRO forwarding, from Maxim Mikityanskiy.
31) TAPRIO offloading in dsa hellcreek driver, from Kurt Kanzenbach.
32) Weighted random twos choice algorithm for ipvs, from Darby Payne.
33) Fix netdev registration deadlock, from Johannes Berg.
34) Various conversions to new tasklet api, from EmilRenner Berthing.
35) Bulk skb allocations in veth, from Lorenzo Bianconi.
36) New ethtool interface for lane setting, from Danielle Ratson.
37) Offload failiure notifications for routes, from Amit Cohen.
38) BCM4908 support, from Rafał Miłecki.
39) Support several new iwlwifi chips, from Ihab Zhaika.
40) Flow drector support for ipv6 in i40e, from Przemyslaw Patynowski.
41) Support for mhi prrotocols, from Loic Poulain.
42) Optimize bpf program stats.
43) Implement RFC6056, for better port randomization, from Eric
Dumazet.
44) hsr tag offloading support from George McCollister.
45) Netpoll support in qede, from Bhaskar Upadhaya.
46) 2005/400g speed support in bonding 3ad mode, from Nikolay
Aleksandrov.
47) Netlink event support in mptcp, from Florian Westphal.
48) Better skbuff caching, from Alexander Lobakin.
49) MRP (Media Redundancy Protocol) offloading in DSA and a few
drivers, from Horatiu Vultur.
50) mqprio saupport in mvneta, from Maxime Chevallier.
51) Remove of_phy_attach, no longer needed, from Florian Fainelli"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1766 commits)
octeontx2-pf: Fix otx2_get_fecparam()
cteontx2-pf: cn10k: Prevent harmless double shift bugs
net: stmmac: Add PCI bus info to ethtool driver query output
ptp: ptp_clockmatrix: clean-up - parenthesis around a == b are unnecessary
ptp: ptp_clockmatrix: Simplify code - remove unnecessary `err` variable.
ptp: ptp_clockmatrix: Coding style - tighten vertical spacing.
ptp: ptp_clockmatrix: Clean-up dev_*() messages.
ptp: ptp_clockmatrix: Remove unused header declarations.
ptp: ptp_clockmatrix: Add alignment of 1 PPS to idtcm_perout_enable.
ptp: ptp_clockmatrix: Add wait_for_sys_apll_dpll_lock.
net: stmmac: dwmac-sun8i: Add a shutdown callback
net: stmmac: dwmac-sun8i: Minor probe function cleanup
net: stmmac: dwmac-sun8i: Use reset_control_reset
net: stmmac: dwmac-sun8i: Remove unnecessary PHY power check
net: stmmac: dwmac-sun8i: Return void from PHY unpower
r8169: use macro pm_ptr
net: mdio: Remove of_phy_attach()
net: mscc: ocelot: select PACKING in the Kconfig
net: re-solve some conflicts after net -> net-next merge
net: dsa: tag_rtl4_a: Support also egress tags
...
|
|
Static checkers complained about an off by one read overflow in
otx2_get_fecparam() and we applied two conflicting fixes for it.
Correct: b0aae0bde26f ("octeontx2: Fix condition.")
Wrong: 93efb0c65683 ("octeontx2-pf: Fix out-of-bounds read in otx2_get_fecparam()")
Revert the incorrect fix.
Fixes: 93efb0c65683 ("octeontx2-pf: Fix out-of-bounds read in otx2_get_fecparam()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These defines are used with set_bit() and test_bit() which take a bit
number. In other words, the code is doing:
if (BIT(BIT(1)) & pf->hw.cap_flag) {
This was done consistently so it did not cause a problem at runtime but
it's still worth fixing.
Fixes: facede8209ef ("octeontx2-pf: cn10k: Add mbox support for CN10K")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch populates the PCI bus info in the ethtool driver query data.
Users will be able to view PCI bus info using 'ethtool -i <interface>'.
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vincent Cheng says:
====================
ptp: ptp_clockmatrix: Fix output 1 PPS alignment.
This series fixes a race condition that may result in the output clock
not aligned to internal 1 PPS clock.
Part of device initialization is to align the rising edge of output
clocks to the internal rising edge of the 1 PPS clock. If the system
APLL and DPLL are not locked when this alignment occurs, the alignment
fails and a fixed offset between the internal 1 PPS clock and the
output clock occurs.
If a clock is dynamically enabled after power-up, the output clock
also needs to be aligned to the internal 1 PPS clock.
v3:
Suggested by: Jakub Kicinski <kuba@kernel.org>
- Remove unnecessary 'err' variable
- Increase msleep()/loop accuracy by using jiffies in while()
- No empty lines between variables
- No empty lines between call and the if
- parenthesis around a == b are unnecessary
- Inconsistent \n usage in dev_()
- Remove unnecessary empty line
- Leave string format in place so static code checkers can
validate arguments
v2:
Suggested by: Richard Cochran <richardcochran@gmail.com>
- Added const to "char * fmt"
- Break unrelated header change into separate patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Code clean-up.
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Code clean-up.
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Code clean-up.
* Remove blank line between variable declarations.
* Remove blank line between:
err = blah(...)
if (err)
...
* Remove unnecessary blank line before/after loop constructs.
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Code clean-up.
* Remove unnecessary \n termination from dev_*() messages.
* Remove 'char *fmt' to define strings to stay within 80 column
limit. Not needed since coding guidelines increased to
100 columns limit.
Keeping format in place allows static code checkers to
validate the arguments.
* Tighten up vertical spacing.
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Removed unused header declarations.
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When enabling output using PTP_CLK_REQ_PEROUT, need to align the output
clock to the internal 1 PPS clock.
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Part of the device initialization aligns the rising edge of the output
clock to the internal 1 PPS clock. If the system APLL and DPLL is not
locked, then the alignment will fail and there will be a fixed offset
between the internal 1 PPS clock and the output clock.
After loading the device firmware, poll the system APLL and DPLL for
locked state prior to initialization, timing out after 2 seconds.
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Samuel Holland says:
====================
dwmac-sun8i cleanup and shutdown hook
These patches clean up some things I noticed while fixing suspend/resume
behavior. The first four are minor code improvements. The last one adds
a shutdown hook to minimize power consumption on boards without a PMIC.
Changes v1 to v2:
- Note the assumption of exclusive reset controller access in patch 3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Ethernet MAC and PHY are usually major consumers of power on boards
which may not be able to fully power off (those with no PMIC). Powering
down the MAC and internal PHY saves power while these boards are "off".
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adjust the spacing and use an explicit "return 0" in the success path
to make the function easier to parse.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the appropriate function instead of reimplementing it,
and update the error message to match the code.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sun8i_dwmac_unpower_internal_phy already checks if the PHY is powered,
so there is no need to do it again here.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a deinitialization function that always returned zero, and that
return value was always ignored. Have it return void instead.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use macro pm_ptr(), this helps to avoid some ifdeffery.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Add two helper functions to release one table and hooks from
the netns and netlink event path.
2) Add table ownership infrastructure, this new infrastructure allows
users to bind a table (and its content) to a process through the
netlink socket.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have no in-tree users, also update the sfp-phylink.rst documentation
to indicate that phy_attach_direct() is used instead of of_phy_attach().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ocelot now uses include/linux/dsa/ocelot.h which makes use of
CONFIG_PACKING to pack/unpack bits into the Injection/Extraction Frame
Headers. So it needs to explicitly select it, otherwise there might be
build errors due to the missing dependency.
Fixes: 40d3f295b5fe ("net: mscc: ocelot: use common tag parsing code with DSA")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
|
|
Support also transmitting frames using the custom "8899 A"
4 byte tag.
Qingfang came up with the solution: we need to pad the
ethernet frame to 60 bytes using eth_skb_pad(), then the
switch will happily accept frames with custom tags.
Cc: Mauri Sandberg <sandberg@mailfence.com>
Reported-by: DENG Qingfang <dqfext@gmail.com>
Fixes: efd7fe68f0c6 ("net: dsa: tag_rtl4_a: Implement Realtek 4 byte A tag")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Robert Hancock says:
====================
Broadcom PHY driver updates
Updates to the Broadcom PHY driver related to use with copper SFP modules.
Changed since v3:
-fixed kerneldoc error
Changed since v2:
-Create flag for PHY on SFP module and use that rather than accessing
attached_dev directly in PHY driver
Changed since v1:
-Reversed conditional to reduce indentation
-Added missing setting of MII_BCM54XX_AUXCTL_MISC_WREN in
MII_BCM54XX_AUXCTL_SHDWSEL_MISC register
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bcm54xx_config_init was modifying the PHY LED configuration to enable link
and activity indications. However, some SFP modules (such as Bel-Fuse
SFP-1GBT-06) have no LEDs but use the LED outputs to control the SFP LOS
signal, and modifying the LED settings will cause the LOS output to
malfunction. Skip this configuration for PHYs which are bound to an SFP
bus.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a flag and helper function to indicate that a PHY device is part of
an SFP module, which is set on attach. This can be used by PHY drivers
to handle SFP-specific quirks or behavior.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The default configuration for the BCM54616S PHY may not match the desired
mode when using 1000BaseX or SGMII interface modes, such as when it is on
an SFP module. Add code to explicitly set the correct mode using
programming sequences provided by Bel-Fuse:
https://www.belfuse.com/resources/datasheets/powersolutions/ds-bps-sfp-1gbt-05-series.pdf
https://www.belfuse.com/resources/datasheets/powersolutions/ds-bps-sfp-1gbt-06-series.pdf
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On cpu architectures w/o dma cache snooping, dma_unmap() is a
is a very expensive operation, because its resulting sync
needs to invalidate cpu caches.
Increase efficiency/performance by syncing only those sections
of the lan743x's rx ring buffers that are actually in use.
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Reviewed-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The buffers in the lan743x driver's receive ring are always 9K,
even when the largest packet that can be received (the mtu) is
much smaller. This performs particularly badly on cpu archs
without dma cache snooping (such as ARM): each received packet
results in a 9K dma_{map|unmap} operation, which is very expensive
because cpu caches need to be invalidated.
Careful measurement of the driver rx path on armv7 reveals that
the cpu spends the majority of its time waiting for cache
invalidation.
Optimize by keeping the rx ring buffer size as close as possible
to the mtu. This limits the amount of cache that requires
invalidation.
This optimization would normally force us to re-allocate all
ring buffers when the mtu is changed - a disruptive event,
because it can only happen when the network interface is down.
Remove the need to re-allocate all ring buffers by adding support
for multi-buffer frames. Now any combination of mtu and ring
buffer size will work. When the mtu changes from mtu1 to mtu2,
consumed buffers of size mtu1 are lazily replaced by newly
allocated buffers of size mtu2.
These optimizations double the rx performance on armv7.
Third parties report 3x rx speedup on armv8.
Tested with iperf3 on a freescale imx6qp + lan7430, both sides
set to mtu 1500 bytes, measure rx performance:
Before:
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-20.00 sec 550 MBytes 231 Mbits/sec 0
After:
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-20.00 sec 1.33 GBytes 570 Mbits/sec 0
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Reviewed-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The following call path suggests that calling unregister_netdev on an
interface that is up will first bring it down.
enetc_pf_remove
-> unregister_netdev
-> unregister_netdevice_queue
-> unregister_netdevice_many
-> dev_close_many
-> __dev_close_many
-> enetc_close
-> enetc_stop
-> phylink_stop
However, enetc first destroys the phylink instance, then calls
unregister_netdev. This is already dissimilar to the setup (and error
path teardown path) from enetc_pf_probe, but more than that, it is buggy
because it is invalid to call phylink_stop after phylink_destroy.
So let's first unregister the netdev (and let the .ndo_stop events
consume themselves), then destroy the phylink instance, then free the
netdev.
Fixes: 71b77a7a27a3 ("enetc: Migrate to PHYLINK and PCS_LYNX")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Maxime Chevallier says:
====================
net: mvneta: implement basic MQPrio support
This is V2 for the MQPrio support in mvneta.
This small series adds basic support for mqprio offloading, by having
the rx queueing mirroring the TCs based on VLAN prio fields.
This was tested on Armada 3700, and proves useful to make sure
high-priority traffic has a better chance not getting dropped when
there's lots of packets incoming.
The first patch of the series deals with the per-cpu interrupts on the
armada 3700. Since they don't work, there were already some patches
applied to keep all queue mappings to CPU0, but there still were some
remaining mappings left to be dealt with.
The second patch implements the MQPrio offloading for the receive path.
Changes in V2 :
- Add a Fixes tag for the first patch
- Fix some warnings and the xmas tree in the second patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement a basic MQPrio support, inserting rules in RX that translate
the TC to prio mapping into vlan prio to queues.
The TX logic stays the same as when we don't offload the qdisc.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to Errata #23 "The per-CPU GbE interrupt is limited to Core
0", we can't use the per-cpu interrupt mechanism on the Armada 3700
familly.
This is correctly checked for RSS configuration, but the initial queue
mapping is still done by having the queues spread across all the CPUs in
the system, both in the init path and in the cpu_hotplug path.
Fixes: 2636ac3cc2b4 ("net: mvneta: Add network support for Armada 3700 SoC")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When police action is created by cls API tcf_exts_validate() first
conditional that calls tcf_action_init_1() directly, the action idr is not
updated according to latest changes in action API that require caller to
commit newly created action to idr with tcf_idr_insert_many(). This results
such action not being accessible through act API and causes crash reported
by syzbot:
==================================================================
BUG: KASAN: null-ptr-deref in instrument_atomic_read include/linux/instrumented.h:71 [inline]
BUG: KASAN: null-ptr-deref in atomic_read include/asm-generic/atomic-instrumented.h:27 [inline]
BUG: KASAN: null-ptr-deref in __tcf_idr_release net/sched/act_api.c:178 [inline]
BUG: KASAN: null-ptr-deref in tcf_idrinfo_destroy+0x129/0x1d0 net/sched/act_api.c:598
Read of size 4 at addr 0000000000000010 by task kworker/u4:5/204
CPU: 0 PID: 204 Comm: kworker/u4:5 Not tainted 5.11.0-rc7-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: netns cleanup_net
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x107/0x163 lib/dump_stack.c:120
__kasan_report mm/kasan/report.c:400 [inline]
kasan_report.cold+0x5f/0xd5 mm/kasan/report.c:413
check_memory_region_inline mm/kasan/generic.c:179 [inline]
check_memory_region+0x13d/0x180 mm/kasan/generic.c:185
instrument_atomic_read include/linux/instrumented.h:71 [inline]
atomic_read include/asm-generic/atomic-instrumented.h:27 [inline]
__tcf_idr_release net/sched/act_api.c:178 [inline]
tcf_idrinfo_destroy+0x129/0x1d0 net/sched/act_api.c:598
tc_action_net_exit include/net/act_api.h:151 [inline]
police_exit_net+0x168/0x360 net/sched/act_police.c:390
ops_exit_list+0x10d/0x160 net/core/net_namespace.c:190
cleanup_net+0x4ea/0xb10 net/core/net_namespace.c:604
process_one_work+0x98d/0x15f0 kernel/workqueue.c:2275
worker_thread+0x64c/0x1120 kernel/workqueue.c:2421
kthread+0x3b1/0x4a0 kernel/kthread.c:292
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:296
==================================================================
Kernel panic - not syncing: panic_on_warn set ...
CPU: 0 PID: 204 Comm: kworker/u4:5 Tainted: G B 5.11.0-rc7-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: netns cleanup_net
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x107/0x163 lib/dump_stack.c:120
panic+0x306/0x73d kernel/panic.c:231
end_report+0x58/0x5e mm/kasan/report.c:100
__kasan_report mm/kasan/report.c:403 [inline]
kasan_report.cold+0x67/0xd5 mm/kasan/report.c:413
check_memory_region_inline mm/kasan/generic.c:179 [inline]
check_memory_region+0x13d/0x180 mm/kasan/generic.c:185
instrument_atomic_read include/linux/instrumented.h:71 [inline]
atomic_read include/asm-generic/atomic-instrumented.h:27 [inline]
__tcf_idr_release net/sched/act_api.c:178 [inline]
tcf_idrinfo_destroy+0x129/0x1d0 net/sched/act_api.c:598
tc_action_net_exit include/net/act_api.h:151 [inline]
police_exit_net+0x168/0x360 net/sched/act_police.c:390
ops_exit_list+0x10d/0x160 net/core/net_namespace.c:190
cleanup_net+0x4ea/0xb10 net/core/net_namespace.c:604
process_one_work+0x98d/0x15f0 kernel/workqueue.c:2275
worker_thread+0x64c/0x1120 kernel/workqueue.c:2421
kthread+0x3b1/0x4a0 kernel/kthread.c:292
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:296
Kernel Offset: disabled
Fix the issue by calling tcf_idr_insert_many() after successful action
initialization.
Fixes: 0fedc63fadf0 ("net_sched: commit action insertions together")
Reported-by: syzbot+151e3e714d34ae4ce7e8@syzkaller.appspotmail.com
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
pull-request: mlx5-next 2021-02-16
The patches in this pr are already submitted and reviewed through the
netdev and rdma mailing lists.
The series includes mlx5 HW bits and definitions for mlx5 real time clock
translation and handling in the mlx5 driver clock module to enable and
support such mode [1]
[1] https://patchwork.kernel.org/project/netdevbpf/patch/20210212223042.449816-7-saeed@kernel.org/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The changes made in eccd540 is enough for xilinx_emaclite to run
without problem on 64-bit systems. I have tested it on a Xilinx
FPGA with RV64 softcore. The architecture limitation in Kconfig
seems no longer necessary.
A small change is included to print address with %lx instead of
casting to int and print with %x.
Signed-off-by: Gary Guo <gary@garyguo.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Horatiu Vulturv says:
====================
bridge: mrp: Extend br_mrp_switchdev_*
This patch series extends MRP switchdev to allow the SW to have a better
understanding if the HW can implement the MRP functionality or it needs
to help the HW to run it. There are 3 cases:
- when HW can't implement at all the functionality.
- when HW can implement a part of the functionality but needs the SW
implement the rest. For example if it can't detect when it stops
receiving MRP Test frames but it can copy the MRP frames to CPU to
allow the SW to determine this. Another example is generating the MRP
Test frames. If HW can't do that then the SW is used as backup.
- when HW can implement completely the functionality.
So, initially the SW tries to offload the entire functionality in HW, if
that fails it tries offload parts of the functionality in HW and use the
SW as helper and if also this fails then MRP can't run on this HW.
Based on these new calls, implement the switchdev for Ocelot driver. This
is an example where the HW can't run completely the functionality but it
can help the SW to run it, by trapping all MRP frames to CPU.
Also this patch series adds MRP support to DSA and implements the Felix
driver which just reuse the Ocelot functions. This part was just compiled
tested because I don't have any HW on which to do the actual tests.
v4:
- remove ifdef MRP from include/net/switchdev.h
- move MRP implementation for Ocelot in a different file such that
Felix driver can use it.
- extend DSA with MRP support
- implement MRP support for Felix.
v3:
- implement the switchdev calls needed by Ocelot driver.
v2:
- fix typos in comments and in commit messages
- remove some of the comments
- move repeated code in helper function
- fix issue when deleting a node when sw_backup was true
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement functions 'port_mrp_add', 'port_mrp_del',
'port_mrp_add_ring_role' and 'port_mrp_del_ring_role' to call the mrp
functions from ocelot.
Also all MRP frames that arrive to CPU on queue number OCELOT_MRP_CPUQ
will be forward by the SW.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for offloading MRP in HW. Currently implement the switchdev
calls 'SWITCHDEV_OBJ_ID_MRP', 'SWITCHDEV_OBJ_ID_RING_ROLE_MRP',
to allow to create MRP instances and to set the role of these instances.
Add DSA_NOTIFIER_MRP_ADD/DEL and DSA_NOTIFIER_MRP_ADD/DEL_RING_ROLE
which calls to .port_mrp_add/del and .port_mrp_add/del_ring_role in the
DSA driver for the switch.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add basic support for MRP. The HW will just trap all MRP frames on the
ring ports to CPU and allow the SW to process them. In this way it is
possible to for this node to behave both as MRM and MRC.
Current limitations are:
- it doesn't support Interconnect roles.
- it supports only a single ring.
- the HW should be able to do forwarding of MRP Test frames so the SW
will not need to do this. So it would be able to have the role MRC
without SW support.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check the return values of the br_mrp_switchdev function.
In case of:
- BR_MRP_NONE, return the error to userspace,
- BR_MRP_SW, continue with SW implementation,
- BR_MRP_HW, continue without SW implementation,
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch extends the br_mrp_switchdev functions to be able to have a
better understanding what cause the issue and if the SW needs to be used
as a backup.
There are the following cases:
- when the code is compiled without CONFIG_NET_SWITCHDEV. In this case
return success so the SW can continue with the protocol. Depending
on the function, it returns 0 or BR_MRP_SW.
- when code is compiled with CONFIG_NET_SWITCHDEV and the driver doesn't
implement any MRP callbacks. In this case the HW can't run MRP so it
just returns -EOPNOTSUPP. So the SW will stop further to configure the
node.
- when code is compiled with CONFIG_NET_SWITCHDEV and the driver fully
supports any MRP functionality. In this case the SW doesn't need to do
anything. The functions will return 0 or BR_MRP_HW.
- when code is compiled with CONFIG_NET_SWITCHDEV and the HW can't run
completely the protocol but it can help the SW to run it. For
example, the HW can't support completely MRM role(can't detect when it
stops receiving MRP Test frames) but it can redirect these frames to
CPU. In this case it is possible to have a SW fallback. The SW will
try initially to call the driver with sw_backup set to false, meaning
that the HW should implement completely the role. If the driver returns
-EOPNOTSUPP, the SW will try again with sw_backup set to false,
meaning that the SW will detect when it stops receiving the frames but
it needs HW support to redirect the frames to CPU. In case the driver
returns 0 then the SW will continue to configure the node accordingly.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the enum br_mrp_hw_support that is used by the br_mrp_switchdev
functions to allow the SW to detect the cases where HW can't implement
the functionality or when SW is used as a backup.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the member sw_backup to the structures switchdev_obj_ring_role_mrp
and switchdev_obj_in_role_mrp. In this way the SW can call the driver in
2 ways, once when sw_backup is set to false, meaning that the driver
should implement this completely in HW. And if that is not supported the
SW will call again but with sw_backup set to true, meaning that the
HW should help or allow the SW to run the protocol.
For example when role is MRM, if the HW can't detect when it stops
receiving MRP Test frames but it can trap these frames to CPU, then it
needs to return -EOPNOTSUPP when sw_backup is false and return 0 when
sw_backup is true.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove #IS_ENABLED(CONFIG_BRIDGE_MRP) from switchdev.h. This will
simplify the code implements MRP callbacks and will be similar with the
vlan filtering.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When 88E1111 is operating in SGMII mode, auto-negotiation should be enabled
on the SGMII side so that the link will come up properly with PCSes which
normally have auto-negotiation enabled. This is normally the case when the
PHY defaults to SGMII mode at power-up, however if we switched it from some
other mode like 1000Base-X, as may happen in some SFP module situations,
it may not be, particularly for modules which have 1000Base-X
auto-negotiation defaulting to disabled.
Call genphy_check_and_restart_aneg on the fiber page to ensure that auto-
negotiation is properly enabled on the SGMII interface.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
